This paper presented a method for calculating daily load curves by considering charging and discharging locations of electric vehicles to help to understand the impact of loads generated by charging and discharging of electric vehicles on the power grid. Based on the estimated PEVs’ share, the PEVs discharge power was calculated to reflect both the characteristics of the arriving vehicle in the morning and the SMP plan after establishing a assumption that the electric vehicle arrived at work in the morning and the electric vehicle arrived at home in the afternoon for each of the charging/discharging locations, that is, work and home, of electric vehicles in the city. After calculating the daily load curve for each charging/discharging power type for the PEVs charging strategy, which takes into account both the characteristics of the vehicle arriving at home in the afternoon and the TOU fare system and the characteristics of the vehicle arriving at work in the morning and the SMP fare system, it was analyzed by comparing the impact assessment on the grid by adding the existing load. The results of this paper provide an accurate understanding of the impact of PEVs charging and discharging loads on the power grid. The results should help to establish PEVs charging and discharging load management plans to prevent overloading the power grids with appropriate SMP and TOU tariffs while curbing the reinforcement and expansion of power grids as much as possible.

Silencing of the fragile X mental retardation 1 (FMR1) gene and consequently lack of synthesis of FMR protein (FMRP) are associated with fragile X syndrome, which is one of the most prevalent inherited intellectual disabilities. FMRP is a multifunctional protein involved in many cellular functions in nearly all subcellular compartments under normal conditions and under conditions of cellular stress in both neuronal and non-neuronal cell types. This is achieved through its trafficking signals, nuclear localization signal (NLS), nuclear export signal (NES), and nucleolar localization signal (NoLS), as well as its RNA and protein binding domains, and is modulated by various post-translational modifications such as phosphorylation, ubiquitination, sumoylation, and methylation. This review summarizes recent advances in understanding the interaction networks of FMRP with a special focus on FMRP stress-related functions, including stress granule formation, mitochondrion and endoplasmic reticulum plasticity, ribosome biogenesis, cell cycle control, and DNA damage response.

Heart failure is a prevalent cardiovascular condition with significant health implications, necessitating effective diagnostic strategies for timely intervention. This study explores the potential of continuous monitoring of non-invasive signals, specifically integrating Photoplethysmogram (PPG) and Electrocardiogram (ECG), for enhancing early detection and diagnosis of heart failure. Leveraging a dataset from the MIMIC-III database, encompassing 682 heart failure patients and 954 controls. Feature selection techniques were used to systematically select key features which were identified for their clinical relevance and significance in capturing cardiovascular dynamics and to reduce computational complexity and to decrease the chance of overfitting the ML algorithms. These features are then utilized to train and evaluate machine learning algorithms, resulting in a model with an impressive accuracy of 98%, sensitivity of 97.60%, specificity of 96.90%, and precision of 97.20%. The integrated approach outperforms single-signal strategies, showcas-ng its potential for early, precise, and non-invasive heart failure diagnosis. Furthermore, the study underscores the significance of continuous monitoring through wearables, emphasizing the benefits of integrating multiple signals for a comprehensive evaluation of cardiovascular health. The proposed approach holds promise for implementation in hardware systems to enable continuous monitoring, aiding in early detection and prevention of critical health conditions.

The wave-particle description of quantum mechanics is briefly reviewed to set an analogy between the quantum mechanics of particles and fields and quantum cosmology. It is shown that quantum cosmology can be seen as a quantum field theory developed in the space of three metrics (the metrics of the spatial sections of the spacetime), where the classical evolution of the universe corresponds to a definite trajectory and the quantum mechanics of matter fields emerges as the first order quantum correction. Like in a quantum field theory developed in an isotropic background, the universes are created in universe-antiuniverse pairs, which might provide us with an explanation for the matter-antimatter asymmetry observed in our universe without going beyond the standard model. Moreover, the states of the matter and the antimatter fields of the pair of universes are entangled and that makes that their initial states are in a non-vacuum state (presumably in a thermal state). That might open the possibility of looking for observable imprints of the creation of universes in pairs is the astronomical data.

Mouse models are frequently used to study Huntington’s disease (HD). Onset and severity of neuronal and behavioral pathologies vary greatly between HD mouse models, which results from different huntingtin expression levels and different CAG repeat length. HD pathology appears to depend also on strain background of mouse models. Thus, behavioral deficits of HD mice are more severe in the FVB than in the C57BL/6 background. Alterations in medium spiny neuron (MSN) morphology and function has been well documented in young YAC128 mice in the FVB background. We here tested the relevance of strain background for mutant huntingtin (mHTT) toxicity on the cellular level by investigating HD pathologies in YAC128 mice in the C57BL/6 background (YAC128/BL6). Morphology, spine density, synapse function and membrane properties were not or only subtly altered in MSNs of 12-month-old YAC128/BL6 mice. Despite the mild cellular phenotype, YAC128/BL6 mice showed deficits in motor performance. More pronounced alterations in MSN function were found in the HdhQ150 mouse model in the C57BL/6 background (HdhQ150/BL6). Consistent with the differences in HD pathology, the number of inclusion bodies was considerably lower in YAC128/BL6 mice than HdhQ150/BL6 mice. This study highlights the relevance of strain background for mHTT toxicity in HD mouse models.

We examine here characteristics of electromagnetic waves that propagate through an unbounded space filled with a homogeneous isotropic chiral medium. Resulting characters are compared to those of the electromagnetic waves propagating through an achiral free space. To this goal, we form energy conservation laws for key bilinear parameters in a chiral case. Due to a nonzero medium chirality, conservation laws turn out to contain extra terms that are linked to the spin-orbit coupling, which is absent for an achiral case. As an example, we take a plane wave for achiral case to evaluate those bilinear parameters. Resultantly, the conservation laws for a chiral case are found to reveal inconsistencies among several bilinear parameters that constitute the con-servation laws , thereby prompting us to establish partial remedies for formulating proper wave-propagation problems.

Fires are complex multi-physics problems that span wide spatial scale ranges. Capturing this complexity in computationally affordable numerical simulations for process studies and “outer-loop” techniques (e.g., optimization and uncertainty quantification) is a fundamental challenge in reacting flow research. Further complications arise for propagating fires where a priori knowledge of the fire spread rate and direction is typically not available. In such cases, static mesh refinement at all possible fire locations is a computationally inefficient approach to bridging the wide range of spatial scales relevant to fire behavior. In the present study, we address this challenge by incorporating adaptive mesh refinement (AMR) in fireFoam, an OpenFOAM solver for simulations of complex fire phenomena involving pyrolyzing solid surfaces. The AMR functionality in the extended solver, called fireDyMFoam, is load balanced, models gas, solid, and liquid phases, and allows us to dynamically track regions of interest, thus avoiding inefficient over-resolution of areas far from a propagating flame. We demonstrate the AMR capability and computational efficiency for fire spread on vertical panels, showing that the AMR solver reproduces results obtained using much larger statically refined meshes, but at a substantially reduced computational cost. We then leverage the computational efficiency of the AMR solver to demonstrate an optimization framework for fire suppression based on the open-source Dakota toolkit.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

Analysis of land use/land cover (LULC) in the catchment areas is the first action toward safeguarding the freshwater resources. The LULC information in the watershed has gained popularity in the natural science field as it helps water resource managers and environmental health specialists develop natural resource conservation strategies based on available quantitative information. Thus, remote sensing is the cornerstone in addressing environmental-related issues at the catchment level. In this study, the performance of four machine learning algorithms (MLAs), such as Random Forests (RF), Support Vector Machine (SVM), Artificial Neural Networks (ANN), and Naïve Bayes (NB) was investigated to classify the catchment into nine relevant classes of the undulating watershed landscape using Landsat 8 Operational Land Imager (L8-OLI) imagery. The assessment of the MLAs were based on the visual inspection of the analyst and the commonly used assessment metrics, such as user’s accuracy (UA), producers’ accuracy (PA), overall accuracy (OA), and kappa coefficient. The MLAs produced good results, where RF (OA= 97.02%, Kappa= 0.96), SVM (OA= 89.74 %, Kappa= 0.88), ANN (OA= 87%, Kappa= 0.86), and NB (OA= 68.64 Kappa= 0.58). The results show the outstanding performance of the RF model over SVM and ANN with a small margin. While NB yielded satisfactory results, which could be primarily influenced by its sensitivity to limited training samples. In contrast, the robust performance of RF could be due to an ability to classify high-dimensional data with limited training data.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

Remote sensing datasets are increasingly being used to provide spatially explicit large scale evapotranspiration (ET) estimates. The focus of this study was to estimate and thematically map on a pixel-by-pixel basis, the actual evapotranspiration (ET_a) of the Wonji Shoa Sugarcane Estate using the Surface Energy Balance Algorithm for Land (SEBAL), Simplified Surface Energy Balance (SSEB) and Operational Simplified Surface Energy Balance (SSEBop) algorithms. The results obtained revealed that the ranges of the daily ETa estimated on January 25, February 26, September 06 and October 08, 2002 using SEBAL were 0.0 - 6.85, 0.0 – 9.36, 0.0 – 3.61, 0.0 – 6.83 mm/day; using SSEB 0.0 - 6.78, 0.0 – 7.81, 0.0 – 3.65, 0.0 – 6.46 mm/day, and SSEBop were 0.05 - 8.25, 0.0 – 8.82, 0.2 – 4.0, 0.0 – 7.40 mm/day, respectively. The Root Mean Square Error (RMSE) values between SSEB and SEBAL, SSEBop and SEBAL, and SSEB and SSEBop were 0.548, 0.548, and 0.99 for January 25, 2002; 0.739, 0.753, and 0.994 for February 26, 2002;0.847, 0.846, and 0.999 for September 06, 2002; 0.573, 0.573, and 1.00 for October 08, 2002, respectively. The standard deviation of ET_a over the sugarcane estate showed high spatio-temporal variability perhaps due to soil moisture variability and surface cover. The three algorithm results showed that well watered sugarcane fields in the mid-season growing stage of the crop had higher ET_a values compared with the other dry agricultural fields confirming that they consumptively use more water. Generally during the dry season, ET_a is limited to water surplus areas only and in wet season, ET_a was high throughout the entire sugarcane estate. The evaporation fraction (ETrF) results also followed the same pattern as the daily ET_a over the sugarcane estate. The total crop and irrigation water requirement and effective rainfall estimated using the Cropwat model were 2468.8, 2061.6 and 423.8 mm/yr for January 2001 planted and 2281.9, 1851.0 and 437.8 mm/yr for March 2001 planted sugarcanes, respectively. The mean annual ET_a estimated for the whole estate were 107 Mm³, 140 Mm³, and 178 Mm³ using SEBAL, SSEB, and SSEBop, respectively. Even though the algorithms should be validated through field observation, they have potential to be used for effective estimation of ET in the sugarcane estate.

Due to related uncertainties brought by changes in energy consumption and the integration of rooftop photovoltaic systems, the accuracy and availability of load profiling data are difficult to achieve. However, project managers and planners use a precise load profile as a crucial tool when determining whether the feeder must be updated or de-loaded. The paper aims to create a non-intrusive monitoring system that predicts the synthetic load profiles behavior of energy consumption using a Light Gradient Boosted and Support Vector Machine (SVM) machine learning technique. The most effective ML algorithm is chosen, and it has the potential to be assessed and verified using validation curves, residuals model generation, and prediction error metrics based on the following key statistical indicators: Mean Absolute Error, Mean Square Error, Root Mean Square Error, R-Square, Root Mean Squared Logarithmic Error, and Mean Absolute Percentage Error. The most effective ML has the potential to be assessed and verified using validation curves, residual model generation, and prediction error metrics based on the following key statistical indicators. The result shows that the estimation of the Irms avg -based on LightGBM is more accurate than the SVM because of its quick, economical, and difficult to overfit, particularly with high-dimensional data, speed, and efficiency of the MAE (3.0698), MSE (15.2757), RMSE (3.9020), RMSLE (0.1433), and MAPE (0.0049) respectively. Additionally, the machine learning model shows that, when compared to the SVM, the LightGBM model had the highest accurate prediction, with R-Square values of 89.8%, 90.3%, and 88.5% for Irms_A_avg, Irms_B_avg, and Irms_C_avg, respectively for Brakfontein Substation supply region, and best represents a diverse customer base.

Prostaglandin E2 (PGE2) is an important biological mediator involved in the defense against Mycobacterium tuberculosis (Mtb) infection. Currently, there are no reports on the mycobacterial components that regulate PGE2 production. Previously, we have reported that RpfE-treated dendritic cells (DCs) effectively expanded the Th1 and Th17 cell responses simultaneously; however, the mechanism underlying Th1 and Th17 cell differentiation is unclear. Here, we show that PGE2 produced by RpfE-activated DCs via the MAPK and cyclooxygenase 2 signaling pathways induces Th1 and Th17 cell responses mainly via the EP4 receptor. Furthermore, mice administered intranasally with PGE2 displayed RpfE-induced antigen-specific Th1 and Th17 responses with a significant reduction in bacterial load in the lungs. Furthermore, the addition of optimal PGE2 amount to IL-2-IL-6-IL-23p19-IL-1β was essential for promoting differentiation into Th1/Th17 cells with strong bactericidal activity. These results suggest that RpfE-matured DCs produce PGE2 that induces Th1 and Th17 cell differentiation with potent anti-mycobacterial activity.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.

Current cellular facts allow us to follow the link from chemical to biochemical metabolites, from the ancient to the modern world. In this context, the "RNA world" hypothesis proposes that early in the evolution of life, the ribozyme was responsible for the storage and transfer of genetic information and for the catalysis of biochemical reactions. Accordingly, the hammerhead ribozyme (HHR) and the hairpin ribozyme, belong to a family of endonucleolytic RNAs performing self-cleavage that might occur during replication. Furthermore, regarding the ultraconserved occurrence of HHR in several genomes of modern organisms (from mammals to small parasites and elsewhere), these small ribozymes have been regarded as living fossils of a primitive RNA world. They fold into 3D structures that generally require long-range intramolecular interactions to adopt the catalytically active conformation under specific physicochemical conditions. By studying viroids as plausible remains of ancient RNA, we recently demonstrated that they replicate in non-specific hosts, emphasizing their adaptability to different environments, which enhanced their survival probability over the ages. All these results exemplify ubiquitously features of life. Those are the versatility and efficiency of small RNAs, viroids and ribozymes, as well as their diversity and adaptability to various extreme conditions. All these traits must have originated in early life to generate novel RNA populations.

The objective of this case report is to introduce a customized CAD/CAM freeze-dried bone allograft (FDBA) block for its use in Guided Bone Regeneration (GBR) procedures for severely deficient maxillary bones. Additionally, a special newly developed remote incision technique is presented to avoid wound dehiscence. The results show an optimal integration behaviour of the FDBA block after six months and the formation of new vital bone. Thus, the results of the present case report confirm the use of the customized CAD/CAM bone block for augmentation of complex defects in the maxillary aesthetic zone as a successful treatment concept.

Anyon is collective excitation of two dimensional electron gas subjected to strong magnetic field, carrying fractional charges and exotic statistical character beyond fermion and boson. So far, anyons with serial fractional charges only exist in fractional quantum Hall effect. It is still a challenge to find new serial of fractional charges in other physical system and develop an unified mathematical physics theory based on the same root. Here a topological path fusion theory of propagating electrons in magnetic flux lattice is proposed to explore the physical origin of fractional charges based on a generalization of Feynman's path integral theory and Thurston's train track theory. This mathematical physics theory generated the existed serial of fractional charges in fractional quantum Hall effect and predicted new serial of fractional charges. A serial of irrational charges are predicted in one dimensional lattice of magnetic fluxes. Fractionally charged anyons are also generated in two dimensional and three dimensional lattice of train tracks of electric currents, revealing an exact correspondence between knot lattice model and train track model. A new explanation for the modular symmetry of complex Hall conductance and composite fermion in fractional quantum Hall effect is also derived from this topological path fusion theory. Experimental observation of anyon in three dimensions can be realized by constructing three dimensional interlocking magnetic fluxes or mapping magnetic fluxes into forbidden zones in multi-connected space filled by solid state material. A photonic crystal with porous nano-structures is a promising system for detecting fractional charges and paves a new way for topological quantum computation.

The use of cow bones for biomaterial is still limited; accordingly, the cow bones waste has low economic value. Basically, a human’s and a cow’s bones are the same in terms of their forming compound. Aluminum (Al) has the potential to combine with hydroxyapatite (HAp) to make metal matrix composites (MMC) that have the potential for biomaterials. Compatible elements to be combined with Al and HAp are magnesium (Mg), titanium (Ti), and Copper (Cu), used self-high propagating temperatures synthesis (SHS). MMC can be processed to be a useful, solid product. Applying pressure to the SHS reaction and heating process may result in biomaterial composite product consisting of some matrix materials such as Al come from cans materials used in the experiment was HAp that was processed from cow bones calcination, added by can that contained aluminum and wetting agent, namely magnesium. The exothermic temperature was 800-900°C. The compaction process was done to allow materials to be bound. Based on the ASTM F138 standard for element of biomaterials, the porosity value was below 30% and hardness level above 40 HV. Cow bones and can-based composite sample with the composition of HAp-Al-Mg: 85%-10%-5% met the standard since the hardness value was: 73.3 HV with a porosity value of 29.88%.

Osteoporotic vertebral fracture is the most common fracture from osteoporosis, and are largely undiagnosed due to the mostly asymptomatic nature of the condition. It increases the risk of subsequent fractures and contributes to societal burden. Risk factors for osteoporotic fractures are found in the WHO fracture risk assessment model and used as a tool for monitoring bone health. Vertebral fractures are diagnosed from anteroposterior and lateral spine radiographs and are confirmed with an approximate loss of 20% vertebral height as compared to adjacent vertebrae. One of the most used grading for vertebral fractures is the SQ grading. Mild vertebral fractures could easily be misdiagnosed due to some peculiarities of the vertebral column. CT scan is useful for planning surgical intervention while an MRI scan can provide information about the recency of the fracture and rule out cancer-related fractures. Management depends on the severity of the fracture which could range from conservative management to surgical vertebral augmentation and decompression. Bisphosphonates are used to treat osteoporosis in acute and long-term management of fractures. Osteoimmunological therapies such as denosumab and romosozumab are new therapeutic interventions for osteoporosis while there are many other potential treatment options. Precision medicine provides an individualized treatment approach while regenerative medicine utilizes mesenchymal stem cells for fracture repair.

The aim of this study was to analyze the level of specific back-health-related physical activity and exercise knowledge. This is a cross-sectional study. A representative sample of 1500 students were recruited with a confidence level of 95% and an accepted standard error of ±2.53%. Individuals were aged between 13 and 18 years old (mean age= 15.18; SD = ±1.446). Self-reported questionnaires were used to record back-health-related physical activity and exercise knowledge concerning back care in adolescents. The level of specific knowledge of back health education related to physical activity and exercise in adolescents was low (X = 2.05, SD = ±2.264). Only 10.9% of the students passed the specific knowledge test, achieving a grade equal or superior to 5. The boys average score was higher (X = 2.17, SD = ±2.312) than the girls (X = 1.94, SD = ±2.212) with statistically significant differences (p = .048). The level of specific knowledge increased with age (F = 11.531; p < .001). High school students have a low level of specific knowledge. Physical Education teachers should apply the conceptual content properly. Knowledge is the first step towards changing behavioral habits. Back care education in the school curriculum is recommended.

In my paper, a divisibility rule named the Queen function is de- scribed, which has been generalized for every integer and encompasses all pre- viously established divisibility rules. Subsequently, the paper discusses other areas where this function is instrumental. These include simplifying ratios, generating prime numbers, and more. Towards the end of the paper, a set of hypotheses is also presented. Among these, the most significant is the novel approach involving the application of the Queen function for prime number generation.

High in reliability, multi in function, strong in tracking and detecting, active phased array antennas have been widely applied in radar system. Heat dissipation is a major technological barrier preventing the realization of next-generation high-performance phased array antennas. As a result of the advancement of miniaturization and the in-tegration of microelectronics technology, the study and development of embedded di-rect cooling or heat dissipation has significantly enhanced the heat dissipation effect. In this paper, a novel swept-back fishnet embedded microchannel topology (SBFEMCT) is designed, and various microchannel models with different fishnet runner mesh den-sity ratios and different fishnet runner layers are established to characterize the chip Tmax, runner Pmax, and Tmax and analyze the thermal effect of SBFEMCT under these two operating conditions. The Pmax is reduced to 72.37% and 57.12% of the original at mesh density ratios of 0.5, 0.25, and 0.125, respectively. The maximum temperature reduction figures are average with little change in maximum velocity and a small increase in maximum pressure drop for the number of fishing mesh runner layers of 0-4. This paper provides a study of the latest embedded thermal dissipation from the dimension of a single chip to provide a certain degree of new ideas and ref-erences for solving the thermal technology bottleneck of next-generation high-performance phased array antennas.

Cinematic texts provide narrative insights into lived experiences. This paper uses a qualitative, content analysis of New Jack City to explore how conservative partisanship affected the African American diaspora during the Reagan Era. I explore how the characterizations and contexts of marginalized personae reflect social scripts and invoke judicial tropes to convey hegemonic institutions. Given the prevalent conditions respective to sociology and psyche, policy is embodied through micro- and macro-phenomena. While the former relates to individual narratives of personal capacity and agency, the latter concerns historical events and precedents.

Artificial Intelligence is dominated by Artificial Neural Networks (ANNs). Currently, the Batch Gradient Descent (BGD) is the only solution to train ANN weights when dealing with large datasets. In this article, a modification to the BGD is proposed which significantly reduces the training time and improves the convergence. The modification, called Instance Eliminating Back Propagation (IEBP), eliminates correctly-predicted-instances from the Back Propagation. The speedup is due to the elimination of unnecessary matrix multiplication operations from the Back Propagation. The proposed modification does not add any training hyperparameter to the existing ones and reduces the memory consumption during the training.

Lower Back Pain (LBP) is a disease that needs immediate attention. Person with back pain shall go immediately to doctor for treatment. Injury, excessive works and some medical conditions are result of back pain. Back pain is common to any age of human for different reasons. Due to factors such as previous occupation and degenerative disk disease the chance of developing lower back pain increases for older people. It hampers the working condition of people common reason for seeking medical treatment. The result is absence from work and is unable to normal due to pain. It creates uncomfortable and debilitating situations. Hence, detecting this disease at an early stage will assist the medical field experts to suggest counter measures to the patients. Detection of lower back pain is implemented in this paper by applying ensemble machine learning technique. This paper proposes Stacking ensemble classifier as an automated tool that will predict lower back pain tendency of a patient. Experimental result implies that the proposed method reaches an accuracy of 76.34%, f1-score of 0.76 and MSE of 0.34.

The movement direction of propagating convective systems originating from both inland and offshore over the north coast of West Java in Indonesia is determined primarily by the prevailing wind. However, the role of a land-sea contrast and a rugged topography over southern West Java is also expected to affect propagating convective systems by increasing land-sea breezes and enhancing upward motion. These hypotheses are tested using a weather prediction model incorporating convection (up to 3 km height) to simulate the heavy rainfall event during 26–29 January associated with the 2002 Jakarta flood. First, we addressed the influence of land-sea contrast and topography on the local circulation, particularly in the area surrounding Jakarta, by replacing the inland topography over western Indonesia (96°–119°E, 17°S–0°) with a water body with an altitude of 0 m. We then compared the results of model simulations with and without topography. The results show that the main role of the topography here is enhancing the upward motion and generating a deep convective cloud in response to the land-based convective system during 26–27 January 2002, which then continuously and rapidly propagates offshore due to the cold pool mechanism. Furthermore, the land-sea contrast has a significant role in increasing sea breeze under the rapidness of the landward propagation system during 28–29 January 2002, which was strengthened by the gravity waves and resulted in early morning convection over coastal regions.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.

Electric streamer discharges (streamers) in air are a very important stage of lightning, taking place before formation of the leader discharge, and with which an electric discharge starts from conducting objects which enhance the background elecric field, such as airplanes. Despite years of research, it is still not well understood what mechanism determines the values of streamer parameters, such as its radius and propagation velocity. The Streamer Parameter Model (SPM) is aimed to understand this mechanism, as well as to provide a way to efficiently calculate streamer parameters. Previously, we demonstrated that SPM results compared well with a limited set of experimental data. In this Brief Report, we compare SPM predictions to the published hydrodynamic simulation (HDS) results.

Numerous researchers acknowledge that occupational pension protects employees. However, the total occupational pension is shared by employees and employers in China, which is a cost. This study aimed to explore the occupational pension on corporate social responsibility (CSR) and organizational resilience. We drew upon insights from cost-stickiness and resource-based theories to develop a model that illuminates how occupational pension affected firms’ stance toward CSR in the context of the COVID-19 pandemic and how this, in turn, has result organizational resilience. This study categorized CSR into strategic and responsive activities based on cost stickiness. We selected a total of 34,145 observations of Chinese listed companies over the period 2010-2023 as a sample to investigate whether occupational pension changes CSR strategies. The results showed that the cost pressure to contribute to occupational pension drove firms to reduce their responsive CSR and boost their strategic CSR. Moreover, strategic CSR improved organizational resilience, but responsive CSR did not. This relationship between occupational pension and CSR was significantly and negatively moderated by the minimum wage and population aging. Whereas, the relationship between CSR and organizational resilience was significantly and positively moderated by digital transformation and marketing capabilities. This study has implications for decision-making regarding high-quality firm development.

Low back pain is prevalent in equestrian athletes, but prevalence and associated factors are unknown in the Portuguese equestrian population. A questionnaire regarding low back pain and possible associated factors was answered by 347 respondents. Estimated 12-month prevalence was 67.1%. The probability of suffering from low back pain was higher in individuals with higher weekly riding workload, that reported equestrianism as their main occupation and that performed daily stable duties. The Roland Morris disability questionnaire was applied to the respondents that stated having experienced low back pain in the past 12 months, resulting in an average score of 5.39 ± 4.42. 63.1% of respondents stated that low back pain impaired their performance. Individuals that stated equestrianism was their main occupation showed a significant higher risk (OR = 1.759) of exhibiting a score ≥ 4, as measure of dysfunctionality. Age and high body mass index were also associated to a dysfunctional score. Further research is needed to fully understand the impacts of low back pain in Portuguese equestrian athletes.

The beginnings of redox biology are recalled with special emphasis on formation, metabolism and function of reactive oxygen and nitrogen species in mammalian systems. The review covers the early history of heme peroxidases and the metabolism of hydrogen peroxide, the discovery of selenium as integral part of glutathione peroxidases, which expanded the scope of the field to other hydroperoxides including lipid hydroperoxide, the discovery of superoxide dismutases and superoxide radicals in biological systems and their role in host defense, tissue damage, metabolic regulation and signaling, the identification of the endothelial-derived relaxing factor as the nitrogen monoxide radical and its physiological and pathological implications. The article highlights the perception of hydrogen peroxide and other hydroperoxides as signaling molecules, which marks the beginning of the flourishing fields of redox regulation and redox signaling. Final comments describe the development of the redox language. In the 18th and 19th century, it was highly individualized and hard to translate into modern terminology. In the 20th century, the redox language co-developed with the chemical terminology and became clearer. More recently, the introduction and inflationary use of poorly defined terms has unfortunately impaired the understanding of redox events in biological systems.

South America has become the new epicenter of the coronavirus, especially in Brazil where the disease continues to spread exponentially across the country. This text aims to analyze the psychosocial factors of Covid-19 on back to school strategies in Brazil from a bioecological perspective. At the microsystem level, the population is experiencing different levels of stress and fear; at the mesosystem level, changes in routines, separation from family and friends, and closure of schools; and at the macrosystem level, national guidelines to control the pandemic, institutional standards on a national and international scale. Therefore, the main focus for the success of school return must be in the prevention of contagion and with physical and psychological health, and should not only consider the demands of curricula, financial or administrative management. For this reason, it is paramount that greater female representativeness is increased in decision-making levels of the meso and macrosystem, regarding the resumption of school and academic activities in the pandemic period, since the number of female leaders in decision-making, is still insufficient.

Fast Field-Cycling (FFC) Nuclear Magnetic Resonance (NMR) relaxometry is a powerful non-destructive magnetic resonance technique that enables, among other things, the investigation of slow molecular dynamics at low magnetic field intensities. FFC-NMR relaxometry measurements provide insight into molecular motion across various timescales within a single experiment. This study focuses on a \textit{model-free} approach, representing the NMRD profile $R_1$ as a linear combination of Lorentzian functions, thereby addressing the challenges of fitting data within an ill-conditioned linear least-squares framework. Tackling this problem, we present a comprehensive review and experimental validation of three regularization approaches to implement the model-free approach to analysing NMRD profiles. These include: (1) \nameUpe, utilizing locally adapted $L_2$ regularization; (2) \nameL, based on $L_1$ penalties; and (3) a hybrid approach combining locally adapted $L_2$ and global $L_1$ penalties. Each method's regularization parameters are determined automatically, according to the Balancing and Uniform Penalty principles. % Our contributions include the implementation and experimental validation of the \nameUpe{} and \nameUp{} algorithms, and the development of a "dispersion analysis" technique to assess the existence range of the estimated parameters. The objective of this work is to delineate the variance in fit quality and correlation time distribution yielded by each algorithm, thus broadening the set of software tools for the analysis of sample structures in FFC-NMR studies. The findings underline the efficacy and applicability of these algorithms in the analysis of NMRD profiles from samples representing different potential scenarios. 1

Factorization reduces computational complexity and is therefore an important tool in statistical machine learning of high dimensional systems. Conventional molecular modeling, including molecular dynamics and Monte Carlo simulations of molecular systems, is a large research field based on approximate factorization of molecular interactions. Recently, the local distribution theory was proposed to factorize global joint distribution of a given molecular system into trainable local distributions. Belief propagation algorithms are a family of exact factorization algorithms for trees and are extended to approximate loopy belief propagation algorithms for graphs with loops. Despite the fact that factorization of probability distribution is their common foundation, computational research in molecular systems and machine learning studies utilizing belief propagation algorithms have been carried out independently with respective track of algorithm development. The connection and differences among these factorization algorithms are briefly presented in this perspective, with the hope to intrigue further development in factorization algorithms for physical modeling of complex molecular systems.

The properties of iterative splitting methods with serial versions have been analyzed since recent years, see [1] and [3]. We extend the iterative splitting methods to a class of parallel versions, which allow to reduce the computational time and keep the bene t of the higher accuracy with each iterative step. Parallel splitting methods are nowadays important to solve large problems, which can be splitted in subproblems and computed independently with the dierent processors. We present a novel parallel iterative splitting method, which is based on the multi-splitting methods, see [2], [10] and [15]. Such a exibilisation with multisplitting methods allow to decompose large iterative splitting methods and recover the bene t of their underlying waveform-relaxation (WR) methods. We discuss the convergence results of the parallel iterative splitting methods, while we could reformulate such an error to a summation of the individual WR methods. We discuss the numerical convergence of the serial and parallel iterative splitting methods and present dierent numerical applications to validate the bene t of the parallel versions.

Background: Chronic Back Pain due to Facet Joint Syndrome is a common and debilitating con-dition. Advances in regenerative medicine have shown that Autologous Unmodified Adipose Tissue-Derived Regenerative Cells (ADRC) provide several beneficial effects [1,2]. These regen-erative cells can differentiate into various tissues [3] and exhibit a strong anti-inflammatory po-tential. ADRCs can be obtained from a small amount of fatty tissue derived from the patient´s abdominal fat. Methods: We report long-term results of 37 patients (age 31-78 years, mean 62.5) suffering from “Facet Joint Syndrome” The pathology was confirmed by clinical, radiological examinations and fluoroscopically guided test injections. Then liposuction was performed. 50-100 cc of fat were harvested. To recover stem cells from adipose tissue, we use the CE-certified Transpose RT™ system from InGeneron GmbH. The cells were then injected under fluoroscopic control in the periarticular fat. Follow-up examinations were performed at one week 1 and 5 years. Results: Every patient reported improved VAS pain at any follow-up (1 week, 1, and 5 years) with ADRCs compared to the baseline. Conclusion: Our observational data indicate that facet joint syndrome patients treated with unmodified adipose tissue-derived regenerative cells experience improved quality of life in the long term.

This paper discusses a MEMS switch that can be fabricated using low temperature (<100^oC) deposition and patterning techniques suitable for the back-end-of-the-line integration with CMOS. The resulting cross-bar switches can be used for electrostatic discharge protection, FPGA implementation, chip security assessment and lock-down, and circuit block power management. We discuss platinum and iron switch with turn-on voltages of ~ 1.8 V. In the case of the iron switches, we also show that they can be magnetized to have “memory” and stay on when turned on. Platinum switch cycling of up to 1000 times did not show any changes in their turn-on voltage and their contact resistance was unchanged. The 10-100 nm switch airgaps were formed using low temperature sputtered sacrificial polysilicon and XeF₂ etching. XeF₂ does not attack any of the metals used in CMOS enabling fabrication of cross-bar switches with any of these metals. Once activated, it takes ∿ 6 to mechanically turn on the switch that can be decreased to ~1 ns by optimizing the device structure. Interestingly, the nm-scale gaps can be used as spark gap as a fast plasma switch to discharge first followed by the activation of the MEMS switch.

Deep learning (DL) algorithms used for DOTATATE PET lesion detection typically require large, well-annotated training datasets. These are difficult to obtain due to low incidence of gastroenteopancreatic neuroendocrine tumors (GEP-NETs), and the high cost of manual annotation. Furthermore, networks trained and tested with data acquired from site specific PET/CT instrumentation, acquisition and processing protocols have reduced performance when tested with offsite data. This lack of generalizability requires even larger, more diverse training datasets. The objective of this study is to investigate the feasibility of improving DL algorithm performance by better matching the background noise in training datasets to higher noise, out-of-domain testing datasets. 68Ga-DOTATATE PET/CT datasets were obtained from two scanners: Scanner1, a state-of-the-art digital PET/CT (GE DMI PET/CT; n=83 subjects), and Scanner2, an older-generation analog PET/CT (GE STE; n=123 subjects). Set1, the data set from Scanner1 was reconstructed with standard clinical parameters (5 minutes; Q.Clear) and list-mode reconstructions (VPFXS 2, 3, 4, and 5-minutes). Set2, data from Scanner2, representing out-of-domain clinical scans, used standard iterative reconstruction (5 minutes; OSEM). Reconstructed datasets were divided into training, validation, and testing datasets in a 60%, 20%, 20% proportion, and a deep neural network was trained with each: Network1 for Scanner1 and Network2 for Scanner2. DL performance (Network1) was tested with out-of-domain test data (Set2). To evaluate the effect of training sample size, we tested DL model performance using a fraction (25%, 50%, and 75%) of Set1 for training. Scanner1, list-mode 2-minute reconstructed data demonstrated the most similar noise level compared that of Set2, resulting in the best performance (F1=0.713). This was not significantly different compared to the highest performance, upper-bound limit using in-domain training for Network2 (F1=0.755; p-value=0.103). Regarding sample size, the F1 score significantly increased from 25% training data (F1=0.478) to 100% training data (F1=0.713; p&lt;0.001). List-mode data from modern PET scanners can be reconstructed to better match the noise properties of older scanners. Using existing data and their associated annotations dramatically reduces the cost and effort in generating these datasets, and significantly improves the performance of existing DL algorithms. List-mode reconstructions can provide an efficient, low-cost method to improve DL algorithm generalizability.

ABSTRACT Underwater mines may destroy friendly submarines and marine habitats, compromising nonmilitary security. Finding credible information is vital to avoiding scams and spotting hazards. This article employs Supervised Machine literacy models to appropriately categorize subsea items like mines or gems based on Sonar sounds. Python constructs three double classifier models using Gorman and Sejnowski (1988) training data. Through the extraction of key aspects from the Sonar signals, such as spectral components and intensity, the models are able to match newly obtained data with the gemstone order or mine. Delicacy decreases the chance of misidentifications in nonmilitary activities. Machine literacy offers full validation that accommodates real-world Sonar data noise and unpredictability. Based on test results, the highest performing algorithm will deliver the required ratio of accuracy to perceptivity for the bracket task. Central keywords: vaticination model, bracket algorithms, supervised machine literacy, SONAR, and aquatic mining emphasize particular foundations. Improved sophistication in spotting undersea Mines let nonmilitary defence systems respond to proven threats only, preventing friendly submarines or sea life from unnecessary damage owing to false duplicity. This work is a promising start to real-world mine detection devices. Further developments may incorporate greater training data sets, real-time testing on subsea platforms equipped with integrated sonar, and optimization for the discovery of new mine-types. Overall, machine learning and Sonar vision decrease signal fluctuation and noise, making it easier to determine accurate boundaries for non-military applications and environmental protection. The recommended automated discovery technique must balance computational efficiency, generalizability, and delicacy. Prior a real crime, new quality control and verification procedures could boost trust even further.

Data Extraction is a technique is called as clustering which is used to retrieve data either from the files or data bases or both. This paper focuses on the performance evaluation parameters of the clustering algorithms based on different parameters or conditions or constraints and parameters which are used to perform the clustering process to get the clusters on the data sets. Therefore best clusters are retrieved when best parameters or conditions or constraints or preferences which are applied on the data sources for the clustering process. These parameters or conditions or constraints are opted by the user called as user preferences.

There is increasing interest in automating train operations of mainline services, e.g. to increase network capacity. Automatic train operation (ATO) is already achieved by several pilot projects, but not implemented on a large scale. Before the general introduction of new or adapted technologies can have a transformative effect on the operation of such a complex system as train operation on mainlines, they have to pass functional, interoperability and performance tests. A virtual preliminary analysis is one way to ensure a smooth as well as safe introduction and implementation. This paper aims to present an approach that applies to the performance testing of ATO systems. Therefore, methods and test standards for technologies enabling automatic operation in other transport sectors are reviewed. The main findings have been adapted, transformed and combined to be used as a general strategy for virtual performance testing in the railway sector. Specifically, universal performance indicators, namely punctuality, accuracy, energy consumption, safety and comfort, are presented. A layer model for scenario description is adapted from the automotive sector, as well as the definition of different scenario types. Lastly, factors that can influence the performance of an ATO algorithm are identified. To demonstrate the developed approach, a straightforward investigation of a case study is conducted using a microscopic train simulator in combination with an ATO algorithm.

Clustering, or otherwise known as cluster analysis, is a learning problem that takes place without any human supervision. This technique has often been utilized, much efficiently, in data analysis, and serves for observing and identifying interesting, useful, or desired patterns in the said data. The clustering technique functions by performing a structured division of the data involved, in similar objects based on the characteristics that it identifies. This process results in the formation of groups, and each group that is formed, is called a cluster. A single said cluster consists of objects from the data, that have similarities among other objects found in the same cluster, and resemble differences when compared to objects identified from the data that now exist in other clusters. The process of clustering is very significant in various aspects of data analysis, as it determines and presents the intrinsic grouping of objects present in the data, based on their attributes, in a batch of unlabeled raw data. A textbook or otherwise said, good criteria, does not exist in this method of cluster analysis. That is because this process is so different and so customizable for every user, that needs it in his/her various and different needs. There is no outright best clustering algorithm, as it massively depends on the user’s scenario and needs. This paper is intended to compare and study two different clustering algorithms. The algorithms under investigation are k-mean and mean shift. These algorithms are compared according to the following factors: time complexity, training, prediction performance and accuracy of the clustering algorithms.

In the current age of the Fourth Industrial Revolution ($4IR$ or Industry $4.0$), the digital world has a wealth of data, such as Internet of Things (IoT) data, cybersecurity data, mobile data, business data, social media data, health data, etc. To intelligently analyze these data and develop the corresponding real-world applications, the knowledge of artificial intelligence (AI), particularly, machine learning (ML) is the key. Various types of machine learning algorithms such as supervised, unsupervised, semi-supervised, and reinforcement learning exist in the area. Besides, the deep learning, which is part of a broader family of machine learning methods, can intelligently analyze the data on a large scale. In this paper, we present a comprehensive view on these machine learning algorithms that can be applied to enhance the intelligence and the capabilities of an application. Thus, this study's key contribution is explaining the principles of different machine learning techniques and their applicability in various real-world applications areas, such as cybersecurity, smart cities, healthcare, business, agriculture, and many more. We also highlight the challenges and potential research directions based on our study. Overall, this paper aims to serve as a reference point for not only the application developers but also the decision-makers and researchers in various real-world application areas, particularly from the technical point of view.

The research methods were used to investigate the following questions: Does a mobility training intervention change tissue stiffness, joint range of motion, and compensate for possible imbalances? Do the interventions influence the pressure pain threshold and the overall well-being?

To systematically assess the effect size of different methods for patients with low back pain. PubMed, Cochrane Library, Web of Science, and Google Scholar. databases were searched in January 2023. This study has been developed in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) Statement. The key search terms were: “Low back pain”, “Back pain”, “SF-36”, “VAS”, “VASP”, “Roland-Morris”, “Oswestry Disability Index”, and “conservative treatment”. The risk of bias was determined for each randomized trial using the Cochrane Risk of Bias Tool, and the methodological index for non-randomized studies (MINORS). The outcomes included SF-36 Mental, SF-36 Physical, VAS, Roland-Morris, and Oswestry Disability Index. R 4.0.5 software was used, and standardized mean difference (SMD) and 95% confidence intervals (CI) were calculated for continuous outcomes, random model. Twenty-five studies were included. Depending on the outcome being measured, the effect size of different methods in treating low back pain varies from small to large as follows: SF-36 Mental (SMD = 0.39, p &lt; 0.0001), SF-36 Physical (SMD = 0.55, p &lt; 0.0001), VAS (SMD = -0.84, p &lt; 0.0001), Roland-Morris (SMD = -0.45, p &lt; 0.0001), and Oswestry Disability Index (SMD = -0.61, p &lt; 0.0001). Our meta-analysis indicates the positive effects of applying different methods in the treatment of low back pain. PROSPERO registration number: CRD42022371282

This work proposes a metaheuristic-based approach for hyperparameter selection in a multilayer perceptron to classify electromyographic signals. The main goal of the study is to improve the performance of the model by optimizing four important hyperparameters: the number of neurons, the learning rate, the epochs, and the training batches. The approach proposed in this work shows that hyperparameter optimization using particle swarm optimization and gray wolf optimizer significantly improves the performance of a multilayer perceptron for classifying EMG motion signals. The final model achieved an average classification rate of 93% for the validation phases. The results obtained are promising and suggest that the proposed approach may be helpful for the optimization of deep learning models in other signal processing applications.

With increasing research focus on industrial anomaly detection, numerous methods have emerged in this domain. Notably, memory bank-based approaches, coupled with kNN distance metrics, have demonstrated remarkable performance in anomaly detection (AD) and anomaly segmentation (AS). However, upon examination of the Back to the Feature (BTF) method applied to the Mvtec-3D AD dataset, it was observed that while it exhibited exceptional segmentation performance, its detection performance was lacking. To address this discrepancy, this study base improves the implementation of BTF, especially the improvement of the anomaly score metric. It posits that different "clusters" necessitate distinct k values in kNN distance metrics. For simplify, this assumption is distilled into the proposition that AD and AS tasks impose differing requirements on the k value in kNN distance metrics. Consequently, the paper introduces the BTM method, which utilizes distinct distance metrics for AD and AS tasks. This innovative approach yields superior AD and AS performance (I-AUROC 93.0%, AURPO 96.9%, P-AUROC 99.5%), representing a substantial enhancement over the BTF method (I-AUROC 5.7% ↑, AURPO 0.5% ↑, P-AUROC 0.2% ↑).

Before the emergence of SARS-CoV-1, MERS-CoV, and most recently SARS-CoV-2, al-ready four other coronaviruses have been circulating in the human population. The alpha coronaviruses NL63 and 229E and the beta coronaviruses OC34 and HKU1. These circulating coronaviruses all cause mild respiratory illness during the winter seasons and most people are already infected in early life. Could antibodies and/or T cells, es-pecially against the beta coronaviruses have offered some form of protection against SARS-CoV-2? Related is the question whether survivors of SARS-CoV-1 or MERS-CoV would be relatively protected against SARS-CoV-2. More importantly, would humoral and cellular immunological memory, generated during the SARS-CoV-2 pandemic, ei-ther by infection or vaccination offer protection against future coronaviruses? Or rather than protection, could antibody dependent enhancement have taken place, a mecha-nism by which circulating corona antibodies enhance the severity of COVID-19? An-other related phenomenon, the original antigen sin, would also predict that the effec-tivity of the immune response to future coronaviruses would be impaired because of reactivation of memory against irrelevant epitopes. Current available evidence indicates that latter scenarios are highly unlikely and that especially cytotoxic memory T cells directed against conserved epitopes of human coronaviruses could at least offer partial protection against future coronaviruses.

The notion of free will seems so intuitive to us that it would be hard, even impossible, to imagine that we live in a world without ever exerting any willpower. This view of reality is not only hindrance to inspiration, it poses a serious threat to our moral and social responsibilities. Nonetheless, many scientific and philosophical schools of thought such as determinism purport free will as a mere illusion. As an attempt to rescue free will put forward by libertarianism, compatibilism or physical indeterminism that either exempts our mind from the universal rules of cause and effect by offering our minds a metaphysical status or substitute free will with random will rooted in the laws of quantum mechanics. This manuscript offers an alternative perspective under a new paradigm of consciousness called physical libertarianism that explicates true free will through the unwavering laws of cause and effect. Based on this paradigm, consciousness is the result of interaction of awareness and decision-making process. By applying awareness to the process of decision-making awareness-based choice selection or true free will is conceived. In return, by assigning the power of decision making to the process of awareness discretionary selection of information for attention or intentional attention is emerged. Through integration of these two mental functions, an independent entity called “I” is formed that differentiates natural intelligence from artificial intelligence. While determinism can aptly describe the world of inanimate objects and artificial intelligence, because of “I,” determinism has no jurisdiction over the realm of natural intelligence.

In this study, a motion control problem for the vessels towed by tugboats or towing ships on the sea is considered. The towed vessels including barge ships are need to have assistance of tugboats. Combining two vessels, some work purposes in the sea or harbor area can be completed. In this study, the authors give newly developed mathematical model and control system strategy. Especially, the system model fully presenting the physical characteristics of two vessels are derived. For controlling the system effectively, it is considered that the towed vessel has no power propulsion system but the rudder is activated to improve the maneuverability. Considering the strong nonlinearities included in the vessel dynamics, the modelled system is presented by nonlinear system without linearization of nonlinear parameters. Thus, the control system for the towed vessel is designed based on the nonlinear control scheme. Exactly, the back-stepping control method is applied to its motion control. Also, the PID control method is applied for comparing with the proposed control strategy.

Low back pain (LBP) is a pandemic and costly musculoskeletal condition in the United States. Patients with LBP may endure surgery, injections, and expensive visits to emergency departments. Some suggest that using physical therapy or chiropractic in the earlier stage of LBP reduces the utilization of expensive health services and lowers the treatment costs. Nevertheless, there is no consistent evidence to declare which one of these methods is a cost-effective treatment within a short (less than a year) period of time. The purpose of this study was to investigate the cost-effectiveness of chiropractic versus physical therapy in the United States. A decision tree analytic model was used for estimating the economic outcomes. The findings showed that in the chiropractic group, the total average cost was $48.56 lower than the physical therapy group, and daily adjusted life years (DALY) was 0.0043 higher than the physical therapy group. Chiropractic care was shown to be a cost-effective alternative compared with physical therapy for adults with at least three weeks of low back pain over six months.

This study investigated whether biogas reactor performance, including microbial community development, in response to a change in substrate composition is influenced by initial inoculum source. Test reactors were first started with two different inocula and operated with the same grass-manure mixture for more than 120 days. These reactors initially showed great differences depending on inoculum source, but eventually showed similar performance and overall microbial community structure. At the start of the present experiment, the substrate was complemented with milled feed wheat, added all at once or divided into two portions. The starting hypothesis was that process performance depends on initial inoculum source and microbial diversity, and thus that reactor performance is influenced by the feeding regime. In response to the substrate change, all reactors showed increases and decreases in volumetric and specific methane production, respectively. However, specific methane yield and development of the microbial community showed differences related to initial inoculum source, confirming the hypothesis. The different feeding strategies had however only minor effects on process performance and overall community structure, but still induced differences in the cellulose-degrading community and in cellulose degradation.

This paper focuses on the integrated guidance and autopilot design with control input saturation in the end-game phase of hypersonic flight. Firstly, uncertain nonlinear integrated guidance and autopilot model is developed with third actuator dynamics, where the control surface deflection has magnitude constraint. Secondly, neural network is implemented in extended state observer (ESO) design, which is used to estimate the complex model uncertainty, nonlinearity and state coupling. Thirdly, a command filtered back-stepping controller is designed with hybrid sliding surfaces to improve the terminal performance. In the process, different command filters are implemented to avoid the influences of disturbances and repetitive derivation, meanwhile solve the problem of unknown control direction caused by saturation. The stability of closed-loop system is proved by Lyapunov theory, and the principles abided by the controller parameters are concluded through the proof. Finally, series of 6-DOF numerical simulations are presented to show the feasibility and validity of the proposed controller.

Machine learning applications often need large amounts of training data to perform well. Whereas unlabeled data can be easily gathered, the labeling process is difficult, time-consuming, or expensive in most applications. Active learning can help solve this problem by querying labels for those data points that will improve the performance the most. Thereby, the goal is that the learning algorithm performs sufficiently well with fewer labels. We provide a library called scikit-activeml that covers the most relevant query strategies and implements tools to work with partially labeled data. It is programmed in Python and builds on top of scikit-learn.

The Stochastic Optimisation Software (SOS) is a Java platform facilitating the algorithmic design process and the evaluation of metaheuristic optimisation algorithms. It reduces the burden of coding miscellaneous methods for dealing with several bothersome and time-demanding tasks such as parameter tuning, implementation of comparison algorithms and testbed problems, collecting and processing data to display results, measuring algorithmic overhead, etc. SOS provides numerous off-the-shelf methods including 1) customised implementations of statistical tests, such as the Wilcoxon Rank-Sum test and the Holm-Bonferroni procedure, for comparing performances of optimisation algorithms and automatically generate result tables in PDF and LaTeX formats; 2) the implementation of an original advanced statistical routine for accurately comparing couples of stochastic optimisation algorithms; 3) the implementation of a novel testbed suite for continuous optimisation, derived from the IEEE CEC 2014 benchmark, allowing for controlled activation of the rotation operator. each testbed function. Moreover, this article comments on the current state of the literature in stochastic optimisation and highlights similarities shared by modern metaheuristics inspired by nature. It is argued that the vast majority of these algorithms are simply a reformulation of the same methods and that metaheuristics for optimisation should be simply treated as stochastic processes with less emphasis on the inspiring metaphor behind them.

The prevalence of back pain (BP) among children and adolescents has increased over recent years. Some authors advocate promoting back-health education in the school setting. It is therefore important to adopt a uniform suite of assessment instruments to measure the various constructs. The present study aimed to perform a cultural adaptation of a validated measurement instrument (BackPEI), beginning with a translation and cultural adaptation phase, followed by a second phase to test reliability using a test-retest design. The translation and cross-cultural adaptation were performed based on the guidelines. Reliability was tested by applying the questionnaire to 224 secondary school students, at two different times with a 7-day interval between the tests. In general, the Spanish version presented adequate agreement for questions 1–20, with only question 9 achieving a low Kappa range of .312 [-.152- .189]. The question about pain intensity did not show differences between the averages for the test (4.72 ± 2.33) and re-test (4.58 ± 2.37) (p = .333), and the responses for these two tests were highly correlated (ICC= .951 [.928- .966]; p= .0001). Psychometric testing indicated that the Spanish version of the BackPEI is well-adapted and reliable, based on the test-retest design, providing similar results to the original Brazilian version.

The prolonged static sitting at the workplace is considered as one of the main risks for development of musculoskeletal disorders (MSDs) and adverse health effects. Factors such as poor posture and extended sitting are perceived to be a reason for conditions such as lumbar hyperlordosis and lower back pain (LBP), even though the scientific explanation of this relationship is still unclear and raises disputes in the scientific community. This publication proposes the low back pain assessment (LBPA) dataset collected through experiment with 100 participants and consisting of photogrammetric images with intentionally placed body markers, calculated postural angles and tags correct and incorrect posture assessed by habilitated rehabilitator, as well as questionnaire-based self-reports regarding the occurrence of LBP and similar symptoms among the participants. Machine learning models trained with this data are employed for recognizing incorrect body postures. Two scenarios have been elaborated for modeling purposes: scenario 1, based on natural body posture tagged as correct and incorrect, and scenario 2, based on incorrect body postures, corrected additionally by the rehabilitator. The achieved accuracies of respectively 75.3% and 85% for both scenarios reveal the potential for future research in enhancing awareness and actively managing posture-related issues that elevate the likelihood of developing lower back pain symptoms.

It is well known that low back pain (LBP) prevalence is high during the course of school age children’s lives. However, literature concerning the initial onset of back pain between ages of 3 and 11 years remains scarce. The present study aimed to analyze the prevalence of LBP in kindergarten and primary school students. 278 (9.9±2.1 years old; 52.2% girls) students from two public kindergarten and primary schools in Valencia, Spain participated in this cross-sectional study. The Nordic questionnaire on LBP was used to ask questions related to the duration of LBP symptoms over time. The lifetime prevalence of LBP was 47.5% (n = 132), a last year prevalence of 44.2% (n = 123), and a last week prevalence of 18.8% (n = 50) was reported. Boys and girls reached lifetime prevalence of 52.3% (n = 64) and 47.7% (n = 82) (χ2 = 1.978, p = .099), respectively. By age group, lifetime episodes of LBP also showed a higher prevalence with increasing age (χ2 = 32.637; p &lt; .001). In summary, our findings suggest that LBP increases with age. In addition, our results further strengthen the evidence that LBP onset could start as young as 10-years-old.

Granulomatosis with polyangiitis (GPA) is an autoimmune disease which is a type of anti-neutrophil cytoplasmic antibody (ANCA)-associated vasculitis that frequently affects the lungs and kidneys. However, GPA limited to a single organ has also been reported. A 73-year-old man was admitted for back pain and fever. We detected elevated levels of inflammatory markers and myeloperoxidase-ANCA. Magnetic resonance imaging indicated diffuse inflammation of the back and psoas muscles. Histology showed degenerated muscle fibers and granulomatosis vasculitis with mixed lymphoplasma cell infiltration. High-dose methylprednisolone therapy improved his symptoms. A final diagnosis of GPA limited to the muscles was made.

Cellular Technology came into existence in Japan in 1979. From that time, we have seen many advances in technology. Currently, most of the person uses either 4G or 5G, among which 5G is a newer technology. 4G network was the first network to use LTE. LTE stands for Long Term Evaluation. Most people get confused between 4G and LTE, they assume both to be the same. In reality, LTE has evolved on the 4G technology. It was first introduced in 2008 to provide higher efficiency and data rates to the cellular network. It was designed to evolve the performance of the networks which includes the evolution of hardware components, optimization of software, power and cost efficiency. This work presents a study on LTE, LTE-A and VoLTE technology. We also discussed about the several packet scheduling algorithms that are being used for transmission of packets. It brings out new opportunities for the researchers to work on increasing the efficiency of those algorithms by modifications.

Convolutional neural networks (CNNs) have proven to be a very efficient class of machine learning (ML) architectures for handling multidimensional data by maintaining data locality, especially in the field of computer vision. Data pooling, a major component of CNNs, plays a crucial role for extracting important features of the input data and downsampling its dimensionality. Multidimensional pooling, however, is not efficiently implemented in existing ML algorithms. In particular, quantum machine learning (QML) algorithms have a tendency to ignore data locality for higher dimensions by representing/flattening multidimensional data as simple one-dimensional data. In this work, we propose using the quantum Haar transform (QHT) and quantum partial measurement for performing generalized pooling operations on multidimensional data. We present the corresponding decoherence-optimized quantum circuits for the proposed techniques along with their theoretical circuit depth analysis. Our experimental work was conducted using multidimensional data, ranging from 1-D audio data, to 2-D image data, to 3-D hyperspectral data, to demonstrate the scalability of the proposed methods. In our experiments, we utilized both noisy and noise-free quantum simulations on a state-of-the-art quantum simulator from IBM Quantum. We also show the efficiency of our proposed techniques for multidimensional data by reporting the fidelity of results.

Moving object detection plays a crucial role in various applications, particularly in traffic surveillance and collision warning systems. However, the high cost of training and slow detection pose significant challenges to the practicality and real-time performance of existing methods. These challenges hinder the practicality and real-time performance of existing methods. The need for a reliable and efficient moving object detection system prompts the search for cost-effective strategies. Enhancing detection speed without sacrificing accuracy is crucial for real-time applications. Overcoming these challenges is essential to advance the field of moving object detection and improve its applicability in various domains. This paper presents a comprehensive review of the literature on moving object detection, proposes novel strategies to overcome the challenges of high training costs and slow detection. The study emphasizes the importance of reliable speed monitoring systems and advancements in control systems to enhance driver assistance on urban highways. Each frame in the dataset undergoes YOLOv6 processing to detect and classify objects, generating bounding box predictions and class probabilities. Optical flow, specifically the Lucas-Kanade method, is then utilized to compute motion vectors between consecutive frames. These motion vectors facilitate object tracking across frames, enabling refined bounding box positions and improving overall object tracking accuracy. The results demonstrate the effectiveness of the proposed technique in reducing training costs, improving detection speed, and maintaining a high level of accuracy when compared to existing methods. The paper concludes by summarizing the findings and highlighting the potential of the proposed strategy for precise and reliable moving object recognition in real-world traffic scenarios

This research investigates the potential benefits of integrating machine learning algorithms and IoT sensors in modern agriculture. The focus is on optimizing crop production and reducing waste through informed decisions about planting, watering, and harvesting crops. The paper discusses the current state of machine learning and IoT in agriculture, highlighting key challenges and opportunities. It also presents experimental results that demonstrate the impact of changing labels on the accuracy of data analysis algorithms. The findings recommend that by analyzing wide-ranging data collected from farms, including real-time data from IoT sensors, farmers can make more informed verdicts about factors that affect crop growth. Eventually, the integration of these technologies can transform modern agriculture by increasing crop yields while minimizing waste. In our studies, we achieve a classification accuracy of 99.59% using the Bayes Net algorithm and 99. 46% using Naïve Bayes Classifier, and Hoeffding Tree algorithms. Our results indicate that we achieved high accuracy results in our experiments in order to increase crop growth.

Weather forecast has a big impact on the global economy, accurate and timely weather forecast is required by all, it affects many aspects of human livelihood and lifestyle, it also plays a critical role in decision making for severe weather management and for primary and secondary sectors like agriculture, transportation, tourism, and industry as they rely on good weather conditions for production and operations. The erratic and uncertain complex nature of the weather makes traditional weather forecasting tedious and a challenging task, traditional weather forecast involves applying technology and scientific knowledge on numerical weather prediction (NWP), and weather radar to solve complex mathematical equations to obtain forecasts based on current weather conditions. These traditional processes utilize expensive, complex physical and computational power to produce forecasts, which can be inaccurate and have various catastrophic impacts on society. In this research, a machine learning-based weather forecasting model was proposed, the model was implemented using 4 classifier algorithms which include Random Forest classifier, Decision Tree Algorithm, Gaussian Naïve Bayes model, and Gradient Boosting Classifier, these algorithms were trained using a publicly available dataset from Kaggle for the city of Seattle for the period 2012 to 2015. The model’s performance was evaluated; the Gaussian Naive Bayes algorithm proved to be the best performing algorithm with a predictive accuracy of 84.153 %.

Hyperspectral image (HSI) classification is a mechanism of analyzing differentiated land cover in remotely sensed hyperspectral images. In the last two decades, a number of different types of classification algorithms have been proposed for classifying hyperspectral data. These algorithms include supervised as well as unsupervised methods. Each of these algorithms has its own limitations. In this research, three different types of unsupervised classification methods are used to classify different datasets i-e Pavia Center, Pavia University, Cuprite, Moffett Field. The main objective is to assess the performance of all three classifiers K-Means, Spectral Matching, and Abundance Mapping, and observing their applicability on different datasets. This research also includes spectral feature extraction for hyperspectral datasets.

As the embedded device and internet of things (IoTs) concept prevalent in today's world, there is an increasing demand for the security and performance requirements on deploying these devices to private and public sectors. The crucial part of it is to protect privacy, confidentiality and integrity, meanwhile, maintain an adequate level of performance during transmission, storage and access of critical information. While the conventional cryptography methods, such as the Advanced Encryption Standard (AES), SHA$-$2 hashing method and RSA and Diffie Hellman for message authentication and identification, work well on systems which have reasonable processing power and memory capabilities. These do not scale well into a world with embedded systems and sensor networks, in conjunction with their nature of smaller size and lower cost. Thus, in the context of resource constrained device, lightweight cryptography methods are proposed to overcome many of the problems of conventional cryptography possessed. This includes constraints related to physical size, processing requirement, memory limitation, energy drain and production cost. This paper provides a survey of the architectures that are defined as replacements for conventional ciphers within an IoTs space and discuss some trends in the design of future lightweight algorithms. The performance metrics are carefully chosen to reflect and assess the suitability for embedded devices. The aim of this research is to identify the various performance metrics applied on different types of symmetric block ciphers especially lightweight ciphers and compare the results on versatile platforms with stream ciphers and public key methods. The comparative analysis on efficient LW cipher will be tested against other similar block ciphers on both MacBook Pro with Intel core and resource constrained device Raspberry Pi with ARM processor.

In the field of stochastic optimisation, the so-called structural bias constitutes an undesired behaviour of an algorithm that is unable to explore the search space to a uniform extent. In this paper, we investigate whether algorithms from a subclass of estimation of distribution algorithms, the compact algorithms, exhibit structural bias. Our approach, justified in our earlier publications, is based on conducting experiments on a test function whose values are uniformly distributed in its domain. For the experiment, 81 combinations of compact algorithms and strategies of dealing with infeasible solutions have been selected as test cases. We have applied two approaches for determining the presence and severity of structural bias, namely a visual and a statistical (Anderson-Darling) tests. Our results suggest that compact algorithms are more immune to structural bias than their counterparts maintaining explicit populations. Both tests indicate that strong structural bias is found only in one of the algorithms (cBFO) regardless of the choice of strategy of dealing with infeasible solutions and cPSO mirror. For other test cases, statistical and visual tests disagree on some cases classified as having mild or strong structural bias: the former one tends to make harsher decisions, thus needing further investigation.

Quantum computers are machines that are designed to use quantum mechanics in order to improve upon classical computers by running quantum algorithms. One of the main applications of quantum computing is solving optimization problems. For addressing optimization problems we can use linear programming. Linear programming is a method to obtain the best possible outcome in a special case of mathematical programming. Application areas of this problem consist of resource allocation, production scheduling, parameter estimation, etc. In our study, we looked at the duality of resource allocation problems. First, we chose a real world optimization problem and looked at its solution with linear programming. Then, we restudied this problem with a quantum algorithm in order to understand whether if there is a speedup of the solution. The improvement in computation is analysed and some interesting results are reported.

This study assessed the potential of back extensor strength as an alternative marker of frailty. A total of 560 farmers were included. Computed tomography scans measured fat and muscle mass volumes at the mid-L4 vertebral level. Back extensor strength was measured in a seated posture. Multivariate linear regression analyzed the associations between back extensor strength and trunk muscle/fat compositions. The participants were divided into two groups based on back extensor strength. Propensity score matching, multivariate logistic regression, and Extreme Gradient Boosting (XGBoost) were employed to evaluate the relationship between Fried's frailty criteria and back extensor strength. Back extensor strength exhibited positive associations with abdominal muscle volume (r = 1.12) as well as back muscle volume (r = 0.89) (p < 0.05). Lower back extensor strength was linked to more frail status, such as reduced grip strength, walking speed, and fre-quent self-reported exhaustion. Multivariate logistic regression indicated a significant association between lower back extensor strength and higher Fried frailty score (OR, 0.990; p<0.05). XGBoost analysis identified back extensor strength as the most important predictor (gain = 0.502) for frailty, surpassing the significance of age (gain = 0.325). These findings suggested the potential of back extensor strength as an alternative frailty marker.

Abstract: Spatially explicit, fine-grained datasets describing historical urban extents are rarely available prior to the era of operational remote sensing. However, such data are necessary to better understand long-term urbanization and land development processes and for the assessment of coupled nature-human systems, e.g., the dynamics of the wildland-urban interface. Herein, we propose a framework that jointly uses remote sensing derived human settlement data (i.e., the Global Human Settlement Layer, GHSL) and scanned, georeferenced historical maps to automatically generate historical urban extents for the early 20th century. By applying unsupervised color segmentation to the historical maps, spatially constrained to the urban extents derived from the GHSL, our approach generates historical settlement extents for seamless integration with the multi-temporal GHSL. We apply our method to study areas in countries across four continents, and evaluate our approach for two U.S. study sites against historical settlement extents derived from the Historical Settlement Data Compilation for the US, HISDAC-US, achieving Area-under-the-Curve values >0.9. Our results are largely in agreement with model-based urban areas from the HYDE database, and demonstrate that the integration of remote sensing derived observations and historical cartographic data sources opens up new, promising avenues for assessing urbanization, and long-term land cover change in countries where historical maps are available.

Back pain is a common symptom that affects all age groups across the globe, when left untreated may eventually lead to disability. A convenient sample selection method was used in this study due to the global Covid-19 pandemic lockdown which was effective in Turkey during the investigation period. Thus, virtual data collection and health education including some health risks were employed. A total population of two hundred adult women was involved in the study but one hundred and twenty-one responses were collected. Findings show that, for socio-demographic characteristics, the pain was found highest in women between the ages of 41-50 and obese/overweight individuals. Although, there was no significant difference recorded in the marital status category. Moreover, statistical mean differences were detected between the scales for ODI (4.18) and BPFS (6.09). Also, p<0.05, paired sample t-test was 0.001 ODI and 0.001 BPFS after the training exercise. This suggests that exercise training is inversely correlated with pain severity which implies that training has a significant influence on pain intensity. Thus, it could be concluded that there is a relationship between the training exercise and ODI/BPFS.

Central nervous system (CNS) uses vision, vestibular, and somatosensory information to maintain body stability. Research has shown that there is more lumbar proprioception error among low back pain (LBP) individuals as compared to healthy people. In this study, two groups of 20 healthy people and 20 non-specific low back pain participants (LBP) took part in this investigation. This investigation focused on somatosensory sensors and in order to alter proprioception, a vibrator (frequency of 70Hz, amplitude of 0.5 mm) was placed on the soleus muscle area of each leg and two vibrators were placed bilaterally across the lower back muscles. Individuals, whose vision was occluded, were placed on two surfaces (foam and rigid) on force plate, and trunk angles were recorded simultaneously. Tests were performed in 8 separate trials; the independent variables were vibration (4 levels) and surface (2 levels) for within subjects and 2 groups (healthy and LBP) for between subjects (4×2×2). MANOVA and multi-factor ANOVA tests were done. Linear parameters for center of pressure (COP) (deviation of amplitude, deviation of velocity, phase plane portrait (PPP), and overall mean velocity) and nonlinear parameters for COP and trunk angle ((recurrence quantification analysis) RQA and Lyapunov exponents) were chosen as dependent variables. Results indicated that NSLBP individuals relied more on ankle proprioception for postural stability. Similarly, RQA parameters for the COP on both sides and for the trunk sagittal angle indicated more repeated patterns of movement among the LBP cohort. Analysis of short and long Lyapunov exponents showed that people with LBP caused no use of all joints in their bodies (non-flexible), are less stable than healthy subjects.

An attractive option for realizing applications in radiation environments is to employ All-Programmable System-on-Chips (APSoCs) thanks to their high-performance computing and power efficiency merits. Despite APSoC's advantages, like any other electronic device, they are prone to radiation effects. Processors found in APSoCs must, therefore, be adequately hardened against ionizing-radiation to become a viable alternative for harsh environments. This paper proposes a novel triple-core lockstep (TCLS) approach to secure the Xilinx Zynq-7000 APSoC dual-core ARM Cortex-A9 processor against radiation-induced soft errors by coupling it with a MicroBlaze TMR subsystem in Zynq's programmable logic (PL) layer. The proposed strategy uses software-level checkpointing principles along with roll-back and roll-forward mechanisms (i.e. software redundancy), and hardware-level processor replication as well as checker circuits (i.e. hardware redundancy). Results of fault injection experiments show that the proposed solution achieved high soft error security by mitigating about 99% of bit-flips injected into both ARM cores' register data.

Soil texture is key information in agriculture for improving soil knowledge and crop performance, so the accurate mapping of this crucial feature is imperative for rationally planning cultivations and for targeting interventions. We studied the relationship between radioelements and soil texture in the Mezzano Lowland (Italy), a 189 km² agricultural plain investigated through a dedicated airborne gamma-ray spectroscopy survey. The K and Th abundances were used to retrieve the clay and sand content by means of a multi-approach method. Linear (simple and multiple) and non-linear (machine learning algorithms with deep neural networks) predictive models were trained and tested adopting a 1:50,000 scale soil texture map. The comparison of these approaches highlighted that the non-linear model introduces significant improvements in the prediction of soil texture fractions. The predicted maps of the clay and of the sand content were compared with the regional soil maps. Although the macro-structures were equally present, the airborne gamma-ray data permits us shedding light on finer features. Map areas with higher clay content were coincident with paleo-channels crossing the Mezzano Lowland in Etruscan and Roman periods, confirmed by the hydrographic setting of historical maps and by the geo-morphological features of the study area.

Abstract: In network science and big data, the concept of finding meaningful infrastructures in networks has emerged as a method of finding groups of entities with similar properties within very complex systems. The whole concept is generally based on finding subnetworks which have more properties (links) amongst nodes belonging to the same cluster than nodes in other groups (A concept presented by Girvan and Newman, 2002). Today meaningful infrastructure identification is applied in all types of networks from computer networks, to social networks to biological networks. In this article we will look at how meaningful infrastructure identification is applied in biological networks. This concept is important in biological networks as it helps scientist discover patterns in proteins or drugs which helps in solving many medical mysteries. This article will encompass the different algorithms that are used for meaningful infrastructure identification in biological networks. These include Genetic Algorithm, Differential Evolution, Water Cycle Algorithm (WCA), Walktrap Algorithm, Connect Intensity Iteration Algorithm (CIIA), Firefly algorithms and Overlapping Multiple Label Propagation Algorithm. These al-gorithms are compared with using performance measurement parameters such as the Mod-ularity, Normalized Mutual Information, Functional Enrichment, Recall and Precision, Re-dundancy, Purity and Surprise, which we will also discuss here.

The architecture, organization and functioning of biocatalytic reaction networks, which are coded in the cell specific genome and which work together in the small space of biological cells, are a fascinating feature of life evolved over more than 3 billion years. The knowledge about the diversity of biocatalytic functions and metabolic pathways sustaining life on our planet is highly important, especially as the currently occurring loss of biodiversity is considered a planetary boundary which is at high risk, and knowledge about the life of current biological organisms should be gained before they become extinct. In addition to the well-known enzymatic reactions involved in biochemical pathways, the enzyme universe offers numerous opportunities for discovering novel functions and pathways. Maintaining thousands of molecules and reactions functioning properly within biological cells, which may be exposed to various kinds of external hazards, environmental stress, enzymatic side reactions or non-enzymatic chemical reactions, is key for keeping cellular life healthy. This review aims at outlining advances in assigning enzyme functions to protein sequences and the discovery of novel biocatalytic functions and pathways.

Low back pain (LBP) is a leading cause of disability. It significantly impacts the patient’s quality of life, limits their daily living activities, and reduces work productivity. To reduce the burden of LBP, several pharmacological and non-pharmacological treatment options are available. This review summarizes the role of heat therapy in the management of LBP. First, we outline the common causes of LBP, then discuss the general mechanisms of heat therapy on (LB)P, and finally review the published evidence regarding the impact of heat therapy in patients with acute or chronic non-specific LBP. This review demonstrates that continuous, low-level heat therapy provides pain relief, improves muscular strength, and increases flexibility. Therefore, this effective, safe, easy-to-use, and cost-effective non-pharmacological pain relief option is still relevant in modern clinical practice.

We study the effect of polymer coating, pressure, temperature and light on the electrical characteristics of monolayer WSe₂ back-gated transistors with quasi-ohmic Ni/Au contacts. We prove that the removal of a layer of poly(methyl methacrylate) or a decrease of the pressure change the device conductivity from p to n-type. We demonstrate a gate-tunable Schottky barrier at the contacts and measure a barrier height of ~70 meV in flat-band condition. We report and discuss a temperature-driven change in the mobility and the subthreshold slope which we use to estimate the trap density at the WSe₂/SiO₂ interface. We study the spectral photoresponse of the device, that can be used as a photodetector with a responsivity of ~0.5 AW^-1 at 700 nm wavelength and 0.37 mW/cm² optical power.

In the radar system, detection represents a basic and important stage in the receiver side. The detection process is based on the thresholding criteria; two philosophies of this criteria, constant and adaptive threshold. The constant threshold is simple in design, but it has a mis-detection and does not control the false alarm rate. As for the adaptive threshold, it is powerful in target detection, and better control of the false alarm rate, where it is called Constant False Alarm Rate (CFAR). Lots of research in the CFAR design, but the gap in the previous works is that there is no CFAR algorithm can be working with all or most environmental fields and all or most target situations.In this paper, The CFAR, which can work with the most environment and most of the target situations, has been presented. The producing the design and implementation of the new practical CFAR processor is presented. Where, the new CFAR is a combination of the properties of three different CFAR algorithm (CA, OSGO, and OSSO), and from two different families; averaging and statistical. Where it has overperformed of it's is 97.25% for simulation and 96.25% for the implementable version for different target situations. The simulation analysis is made by using Matlab 2015, while the implementation is done by using Xilinx Spartan 700 3a.

Opioid use disorder has increased in the world in recent years and Iran ranks first in terms of opium smoking in the world. In fact, opium smoking by traditional methods, in addition to dependence on morphine, is a behavioral addiction in Iran. The body position during opium smoking is usually non-standard and non-ergonomic. Over time, changes in muscle tissue, tendons and ligaments, and the connective tissue go from elasticity to neuromuscular plasticity. This study aims to compare sway back posture and musculoskeletal problems between opium smokers and non-drug users. In this comparative and cross-sectional study, 80 opium smokers were compared with 74 non-drug users in terms of sway angle (sway back posture), and musculoskeletal complaints (NORDIC questionnaire) and the association of possible risk factors was investigated. Data were analyzed by Kolmogorov-Smirnov, Correlation Coefficient and paired-t tests using SPSS version 23. There were significant differences between two groups in terms of sway back posture (P=0.007), and neck (<0.001), upper back (<0.001) and lower back (0.006) musculoskeletal complaints. Homelessness, the lifetime duration of opium smoking (in months), and the duration of daily opium smoking (in minutes) had significant correlation with sway back posture and musculoskeletal complaints. Homelessness was the strongest predictor and had strongest correlation. Overall, an increase in the duration of sitting in non-ergonomic positions could lead to increase in sway angle and sway back posture and increase in musculoskeletal complaints of neck, upper back and lower back due to the non-neutral posture of opium smoking. It seems that plasticity and structural and functional adaptations of the posture occurs due to opium smoking and further studies are recommended.

In recent years, it has become common for individuals to juggle employment and unpaid care work. This is just as true for the England-based academic workforce, our focus in this article. We discuss how, in the context of English HE, support for carers is enacted and negotiated through policies and practices of care. Our focus on academics with a diverse range of caring responsibilities is unusual insofar as the literature on care in academia is overwhelmingly concerned with parents, usually mothers. The article is informed primarily by critical and post-structuralist feminist perspectives. We draw on a corpus of 47 interviews conducted with academics representing a broad range of caring responsibilities, subjects, and positions. A thematic analysis reveals how carers’ relationship with the provision and policies of care support at institutional level is characterised by ambiguity. On the one hand, participants approve of societal and institutional policy support for carers. On the other hand, they are often reluctant to position themselves as the beneficiary of such policies, expressing instead a general preference for support from outside the workplace or for workplace-based inter-individual and informal care arrangements. This resistance is particularly noticeable in the case of participants with caring responsibilities other than the parenting of healthy, able-bodied children and of those whose gender, class, racial, or sexual identity do not conform with the figure of the ‘ideal academic’, contributing to their othering in the academic realm. These findings have significant implications for policies supporting carers, pointing to the need for greater visibility and recognition of caring responsibilities in academia, especially in terms of their diverse identities.

The development of reliable predictive algorithm for house price as the housing market is a stand-out among the most involved regarding valuing the price and continues to fluctuate, is constantly a need for socio-economic advancement and welfare of citizen. In this paper, we develop machine learning algorithms for forecasting UK housing Price, and find an optimal algorithm that forecasts housing price accurately on the premises of the presence of many features or covariates. After applying correlation analysis to remove correlated variables in order to avoid multicollinearity, thereby increasing the statistical power, a novel method of using regression analysis to first of all understand and select statistically significant features for the various regions in England based on North South divide is adopted. These features are then used in the machine learning algorithm to further increase the statistical power of the algorithm, increase the level of accuracy for each of them and ultimately increase the predictive values for the algorithms. The model construction involves 3 stages: 1- correlation analysis to identify and remove correlated variables thereby avoiding multicollinearity and increasing the statistical power of the linear regression, 2 - using linear regression to determine variables that are statistically significant and 3 - building the machine learning algorithms based on the variables that are statistically significant from the linear regression. A comprehensive dataset of UK Paid housing Price from 2010 to 2019 was linked to a number of other datasets to generate a total 21 variables or features used for the models. Catboost, Gradient Boosting, Bagging, Random Forest, Extra Tree all achieved the excellent models performance result in all the regions considered. The comparison of the seven models showed that Extra Tree algorithm consistently achieved the best performance in term of level of accuracy in all the regions. K-Nearest Neighbours (KNN) is the only algorithm with less than 50% level of accuracy. Noticeably, the regions considered had varying or differing insignificant variables, implying that although many variables are common (statistically significant) to all the regions, there are regional differences and impact when modelling or predicting housing prices. This study validates the practicability of developing a machine learning methodology for the prediction of housing price. This research offers a reference for future house price prediction based on machine learning.

This work proposes a physics-based identification technique based on genetic algorithms. The main objective is to obtain a parametric matrix A that describes the time-invariant linear model of the longitudinal dynamics of an aircraft. This is achieved by proposing a fitness function based on the properties of the transition matrix and taking advantage of some of the capabilities of the genetic algorithm, mainly those of restricting the search ranges of the unknowns. In this case, such unknowns are related to the type of aircraft and flight conditions that are considered during the identification process. The proposed identification method is validated with a reliable nonlinear model that can be found in the literature, as well as with the calculation of the trim condition and linearization generally used in aircraft dynamics. In summary, this study suggests the genetic algorithm provided with the adequate fitness function, could be an appealing alternative for aircraft model identification, even when only a limited amount of data is available. Furthermore, in some cases, linearization using genetic algorithm can be more efficient than classical methods.

This study addressed algorithmic bias in predictive policing, focusing on the Chicago Police Department's Strategic Subject List (SSL) dataset. We specifically focused on identifying and mitigating age-related biases, a notably underexplored area in prior research. Our research introduced Conditional Score Recalibration as a bias mitigation strategy alongside the well-established Class Balancing technique. Conditional Score Recalibration involved reassessing and adjusting risk scores for individuals initially assigned moderately high-risk scores in the dataset. This recalibration marked such individuals as low risk if they met three conditions, namely: no prior arrests for violent offenses, no previous arrests for narcotic offenses, and having never been involved in shooting incidents. These fairness strategies were implemented on the Random Forest model, and the fairness metrics employed included Equality of Opportunity Difference, Average Odds Difference, and Demographic Parity. The results showed a significant improvement in model fairness, particularly for age biases, without compromising the model's accuracy. These findings challenged the often-assumed trade-off between fairness and accuracy, underscoring the feasibility of achieving fairness without compromising accuracy.

This Article demonstrates how an eigendecomposition problem is inputted into a quantum circuit, how gates are applied in the quantum circuit, and how the output measurements are the correct eigenvalues. This process is known as quantum phase estimation (QPE). A quantum harmonic oscillator example, a foundational quantum physical chemistry problem, is demonstrated within the context of QPE. A particle in a box example, another quantum physical chemistry problem, may be solved by QPE with a caveat. These examples are of the limiting cases of diagonal matrices. Future advances in taking matrix inverses for solving linear sets of equations or finding ground state energies in the Schrödinger equation will use the principles implemented in this Article.

Creating self-learning algorithms, developing deep neural networks and improving other methods that "learn" for various areas of human activity is the main goal of the theory of machine learning. It helps to replace the human with a machine, aiming to increase the quality of production. The theory of artificial neural networks, which already have replaced the humans in problems of detection of moving objects, recognition of images or sounds, time series prediction, big data analysis and numerical methods remains the most dispersed branch of the theory of machine learning. Certainly, for each area of human activity it is necessary to select appropriate neural network architectures, methods of data processing and some novel tools from applied mathematics. But the universal problem for all these neural networks with specific data is the achieving the highest accuracy in short time. Such problem can be resolved by increasing sizes of architectures and improving data preprocessing, where the accuracy rises with the training time. But there is a possibility to increase the accuracy without time growing, applying optimization methods. In this survey we demonstrate existing optimization algorithms of all types, which can be used in neural networks. There are presented modifications of basic optimization algorithms, such as stochastic gradient descent, adaptive moment estimation, Newton and quasi-Newton optimization methods. But the most recent optimization algorithms are related to information geometry, for Fisher-Rao and Bregman metrics. This approach in optimization extended the theory of classic neural networks to quantum and complex-valued neural networks, due to geometric and probabilistic tools. There are provided applications of all introduced optimization algorithms, what delighted many kinds of neural networks, which can be improved by including any advanced approaches in minimization of the loss function. Afterwards, we demonstrated ways of developing optimization algorithms in further researches, engaging neural networks with progressive architectures. Classical gradient based optimizers can be replaced by fractional order, bilevel and, even, gradient free optimization methods. There is a possibility to add such analogues in graph, spiking, complex-valued, quantum and wavelet neural networks. Besides the usual problems of image recognition, time series prediction, object detection, there are many are other tasks for modern theory of machine learning, such as solving problem of quantum computations, partial differential and integro-differential equations, stochastic processes and Brownian motion, making decisions and computer algebra.

Renewable Energy Communities (RECs) are emerging as an effective concept and model to empower the active participation of citizens on the energy transition, not only as energy consumers, but also as promoters of environmentally friendly energy generation solutions. This paper aims to contribute to the management and optimization of individual and community Distributed Energy Resources (DER). The solution follows a price and source-based REC management program, in which consumers day-ahead flexible loads (Flex Offers) are shifted according to electricity generation availability, prices and personal preferences, to balance the grid and incentivize user participation. The heuristic approach used in the proposed algorithms allows the optimization of energy resources in a distributed edge and fog approach with a low computational overhead. The simulations performed using real world energy consumption and flexibility data of a REC with 50 dwellings show an average cost reduction of 10.6% and an average increase of 11.4% in individual self-consumption. Additionally, the case-study demonstrates promising results regarding grid load balancing and the introduction of intra-community energy trading.

Metabolic pathways provide key information to achieve a better understanding of life and all its processes; this is useful information for the improvement of medicine, agronomy, pharmacy, and other similar areas. The main analysis tool used to study these pathways is based on the idea of pathway comparison, using graph data structures. Metabolic pathway comparison has been defined as a computationally complex task \cite{ay2011submap,abaka2013campways}. In previous work from 2017, two different approaches that simplify the problem of comparing pathways represented as graphs were introduced. The first algorithm consists of the transformation of a two-dimensional graph structure, representing a metabolic pathway, to a one-dimensional structure and thus aligning the corresponding data using a reduced 1 dimension string. The second algorithm consists of performing a paired analysis between reactions in pathways and thus eliminating all similarities, finally, showing these differences to the user. The suggestion is to use the information provided by these algorithms as a previous analysis to a deeper, more expensive, comparison tool use. Here we provide an extension of this work with more data and deeper analysis. These methods have shown to be an effective way to treat the problem of metabolic pathway comparison as listed in the discussion and results section. Our results show evidence of a quick, simple and effective way to resolve the described problem.

The main purpose of this paper is to propose a novel optimization model with a new machine learning approach in the first section to achieve the best results in financial institutions in the second section. Since the constancy of efficacy derived from parametric and non-parametric is not significant, this paper provides a scientific assessment at the optimization section and proposes a novel combined parametric and non-parametric model which will be a new experiment in literature perception. A scientific assessment of banks based on a combination of the efficiency measurement method of CCR(Charnes, Cooper and Rhodes model) or CRS(Constant Return to Scale) BCC(Banker, Charnes, and Cooper model) or VRS (Variable Return to Scale) in Data Envelopment Analysis (DEA), as well as Stochastic Frontier Approach (SFA) for 65 banks during Feb to July 2020, are introduced. For analyzing the performance of the parametric and non-parametric approaches we have considered the linear regression and Unreplicated Linear Functional Relationship (ULFR). At the machine learning section, a novel four-layers data mining filtering pre-processes for selected supervised classification as well as unsupervised clustering algorithms to increase the accuracy and to remove unrelated attributes and data are applied. For the four kinds of preprocessing approaches of unsupervised attributes, supervised attributes, supervised instances, and unsupervised instances, we have chosen discretization, attribute selection, stratified remove folds, and resample filters respectively. Based on the nature of the suggested financial institution's dataset and attributes, the most appropriate preprocessing filter in each layer to achieve the highest performance is suggested. Finally, the superior bank, best performance model, and the most accurate algorithm are introduced. The results indicate that the bank number 56 is the superior bank. Among the proposed techniques, the novel recommended CVS compared with CCR-BCC and SFA models, has a more positive correlation with profit risk, and show a higher coefficient of determination values. Sequential Minimal Optimization(SMO) algorithm receives the highest accuracy in all four suggested filtering layers.

Typical modern information systems are required to process copious data. Conventional manual approaches can no longer effectively analyze such massive amounts of data, and thus humans resort to smart techniques and tools to complement human effort. Currently, network security events occur frequently, and generate abundant log and alert files. Processing such vast quantities of data particularly requires smart techniques. This study reviewed several crucial developments of existent data mining algorithms, including those that compile alerts generated by heterogeneous IDSs into scenarios and employ various HMMs to detect complex network attacks. Moreover, sequential pattern mining algorithms were examined to develop multi-step intrusion detection. These studies can focus on applying these algorithms in practical settings to effectively reduce the occurrence of false alerts. This article researched the application of data mining algorithms in network security. The academic community has recently generated numerous studies on this topic.

Music acoustics is an interdisciplinary field and mathematics is the basis in the music art form. Music and mathematics correlation exist since the inception of music. Various philosophers, scientists, mathematicians and musicians have expressed their views about this relationship. This paper attempts to explore this association with focus on melodic pattern identification. Mathematics in Indian Classical music with raga as the basis and just intonation tuning system is discussed. Indian vocal music clips are used for different pitch estimation algorithms in the experimentation. Harmonic product spectrum and auto-correlation algorithms are tested for accurate pitch estimation. Enhanced auto-correlation function using audio segmentation is compared with other approaches for effective pitch extraction. Results indicate pitch extraction with enhanced auto-correlation function provides accurate results as compared with other approaches tested.

In this paper we develop a forecasting algorithm for recurrent patterns in consumer demand. We study this problem in two different settings: pull and push models. We discuss several features of the algorithm concerning sampling, periodic approximation, denoising and forecasting.

Intelligent Transportation Systems (ITS) encompasses technologies, services, and applications facilitating communication between vehicles (V2V) and between vehicles and fixed infrastructure (V2I and I2V). This mutual interaction constitutes a Vehicular Ad-Hoc Network (VANET) which supports a plethora of applications targeting critical transportation aspects, such as safety, mo-bility, and environmental considerations. Dedicated Short Range Communications (DSRC), op-erating on the 5.9 GHz band, is pivotal for such exchanges. We introduced an innovative algorithm designed to identify jamming attacks and transition the Safety Application to a secure fail-safe mode. This algorithm leverages a dual-metric strategy, incorporating both distance and PDR measurements. Field tests confirm that our algorithm adeptly recognizes the activities of deceptive jammers, ensuring a prompt shift of the safety application into its fail-safe state. This paper delves into these countermeasures, evaluating their efficiency via mathematical modelling, simulations, and on-ground testing. Findings acknowledge that these strategies bolster the reliability of safety applications in jamming scenarios. Furthermore, the approaches propounded align with ongoing standardization endeavours by relevant authorities, ensuring communication mediums remain unhindered.

We developed a novel hybrid approach for solving global optimization, computer science, bio-medical and engineering real life applications that is based on the coupling of the Whale Optimizer and Sine Cosine Algorithms via a surrogate model. We relate the whale optimizer algorithm to balance between the exploitation and the exploration process in the proposed method. There exist confirmed techniques for searching approximate best optimal solutions, but our algorithm will further guarantee that such numerical and statistical solutions satisfy physical bounds of the standard and real life functions. Our experiments with the benchmark, bio-medical, computer science and engineering real life problems have illustrated the advantages of using a newly hybrid approach based on mixing Whale Optimizer and Sine Cosine algorithms. It holds considerable potential for reducing execution time for solving standard and real life problems and at the same time improving the quality of the solution.

Machine learning plays a key role in present day crime detection, analysis and prediction. The goal of this work is to propose methods for predicting crimes classified into different categories of severity. We implemented visualization and analysis of crime data statistics in recent years in the city of Boston. We then carried out a comparative study between two supervised learning algorithms, which are decision tree and random forest based on the accuracy and processing time of the models to make predictions using geographical and temporal information provided by splitting the data into training and test sets. The result shows that random forest as expected gives a better result by 1.54% more accuracy in comparison to decision tree, although this comes at a cost of at least 4.37 times the time consumed in processing. The study opens doors to application of similar supervised methods in crime data analytics and other fields of data science

The need to increase the energy efficiency of buildings as well as the use of local renewable heat sources has caused that heat meters are used not only to calculate the consumed energy but also for the active management of central heating systems. Increasing the reading frequency and the use of measurement data to control the heating system expands the requirements for the reliability of heat meters. The aim of the research is to analyse a large set of meters in the real network and predict their faults to avoid inaccurate readings, incorrect billing, heating system disruption and unnecessary maintenance. The reliability analysis of heat metres, based on historical data collected over several years, shows some regularities which cannot be easily described by physics-based models. The failure rate is almost constant and does depend on the past but is a non-linear combination of state variables. To predict meters' failures in the next settlement period, three independent machine learning models are implemented and compared with selected metrics because even the high performance of a single model (87\% True Positive for Neural Network) may be insufficient to make a maintenance decision. Additionally, performing hyperparameters optimisation boosts models' performance by a few percent. Finally, three improved models are used to build an ensemble classifier which outperforms the individual models. The proposed procedure ensures the high efficiency of fault detection (>95\%), while maintaining overfitting at the minimum level. The methodology is universal and can be utilised to study the reliability and predict faults of other types of meters and different objects with the constant failure rate.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

Sport has the potential to support psychosocial development in young people. However, extant studies have tended to evaluate purpose-built interventions, leaving regular organised sport relatively overlooked. Moreover, previous work has tended to concentrated on a narrow range of outcomes. To address these gaps, we conducted a season-long ethnography of a youth performance sport club based on a novel Realist Evaluation approach [1]. We construed the club as a social intervention within a complex system of agents and structures. In this - Part 1 - account we detail the perceptions of former and current club parents, players and coaches, using them to build a set of programme theories. The resulting network of outcomes (i.e. self, emotional, social, moral and cognitive) and generative mechanisms (i.e., the attention factory, the greenhouse for growth, the personal boost, and the real-life simulator) spanning across multiple contextual layers provides a nuanced understanding of stakeholders’ views and experiences. This textured perspective of the multi-faceted process of development provides new insights for administrators, coaches and parents to maximise the developmental properties of youth sport, and signposts new avenues for research in this area.

Groundwater represents a pivotal asset in conserving natural water reservoirs for potable consumption, irrigation, and diverse industrial uses. Nevertheless, human activities intertwined with industry and agriculture contribute significantly to groundwater contamination, highlighting the critical necessity to appraise water quality for safe drinking and effective irrigation. This research primarily focused on employing the Water Quality Index (WQI) to gauge water's appropriateness for these purposes. However, the generation of an accurate WQI can prove time-intensive owing to potential errors in sub-index calculations. In response to this challenge, an artificial intelligence (AI) forecasting model was devised, aiming to streamline the process while mitigating errors. The study collected 422 data samples from Mirpurkash, a city nestled in the province of Sindh, for a comprehensive exploration of the region's WQI attributes. Furthermore, the study probed into unraveling the interdependencies amidst variables in the physiochemical analysis of water. Diverse machine learning classifiers were employed for WQI prediction, with findings revealing that random forest and gradient boosting eclipsed other algorithms, achieving an accuracy rate of 99%. In close pursuit were SVM and XGBoost, registering accuracy scores of approximately 95% and 93%, respectively, while KNN and Decision Trees garnered accuracy rates of 88% and 87%, respectively. In addition to WQI prediction, the study conducted an uncertainty analysis of the models using the R-factor, providing insights into the reliability and consistency of predictions. This dual approach, combining accurate WQI prediction with uncertainty assessment, contributes to a more comprehensive understanding of water quality in Mirpurkash and enhances the reliability of decision-making processes related to groundwater utilization

The texture properties of cooked rice are a dominant property which can indicate the eating quality. Evaluation of back extrusion (BE) test precision and sensitivity for cooked germinated brown rice (GBR) texture in production process was investigated in this study. BE test on texture properties of cooked GBR rice show high precision of measurement of hardness, toughness and stickiness tests which indicated by the repeatability and reproductivity test but the sensitivity indicated by coefficient of variation of the texture properties. The findings of the study of the effect of different soaking and aging duration in the production of Khao Dawk Mali 105 (KDML 105) GBR on cooked GBR texture measured by BE test confirmed the developed protocol for evaluation of high precision and sensitivity of the texture measurement method. Repeatability and reproducibility of reliable measurements have a low standard deviation of the farthest different between replicates, which is considered high precision. High coefficient of variation where the relative wide variation of the absolute value of the property can be detected indicate high sensitivity which even small resolution can be detected or vice versa. But the correlation coefficient among the texture properties by BE were not related to the precision or sensitivity of the test. By these results, the original protocol for determination of precision and sensitivity of food texture measurement was successfully verified as the usable evaluation protocol for GBR texture measurement.