Bamboo engineering materials are green, high-strength, tough, durable, and structurally safe, and have promising application prospects in various modern green and low-carbon buildings. To invest the vibration behavior of new bamboo bundle veneer -laminated lumber (BLVL) for use in floor slabs, this study designed two kinds of full-scale vibration tests under a pedestrian load: an extraction hammer impact test, and a static concentrated load test, it is expected to provide theoretical and data support for the application of bamboo bundle veneer laminated composite materials in the construction field. The results showed that the self-oscillation frequency and mid-span deflection of the BLVL composite met the requirements of multiple relevant regulations when used as the structural material of floor slabs. The BLVL floor slab had a higher flexural stiffness and better vibration-damping performance than the OSB floor slab. The first-order self-oscillation frequency of the BLVL composite floor slab was 13.769 Hz, the damping ratio of the first three orders of modalities was 1.262–2.728%, and the maximum static deflection in the span of the joist was 0.932 mm under a 1 kN concentrated load. The 1 kN static deflection of the BLVL was reduced by 22.33%, and the root mean square (RMS) acceleration of the walking load response was significantly lower than that of the OSB floor slab. The preparation of BLVL composite materials by homogeneous lamination of bamboo bundle veneer and wood veneer may help improve the vibration behavior of bamboo-wood structures such as floor slabs and walls.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Imitation learning, also known as programming by demonstration, has been shown to be a promising paradigm for intuitive robot programming by non-expert users. However, the classical kinesthetic approach with physical hand guidance suffers from generalizability across different robot types and is impractical for demonstrating tasks with long horizons. Visual imitation learning enables the recording of multi-step tasks as a single continuous video, allowing non-experts to demonstrate tasks naturally. Existing approaches typically require a large amount of data to develop end-to-end deep learning models that map raw pixels to robot actions. This paper explores the application of visual imitation learning from one-shot demonstration, significantly reducing the data requirements and simplifying the programming process. To achieve this target, a framework is proposed to map hand trajectories to the robot end-effector, consisting of four essential components: hand detection; object detection; segmentation of the trajectories into elemental skills; and learning the skills. Methods are developed for each component and evaluated on recorded videos to demonstrate the effectiveness of the proposed framework.

Ming-style round-backed armchairs as a classic Chinese chair design are renowned for the blend of ergonomics, practicality, and elegance. Although the Chinese armchair furniture industry has made strides in sustainability, there is still a need for further improvements in material selection, manufacturing processes, and supply chain management to fully support the development of sustainable furniture. Laminated bamboo lumber as new sustainable materials are becoming a popular option for furniture designers in the era of "sustainable design". This research aims to investigate the feasibility and application of laminated bamboo lumber in the design of Chinese armchair furniture and proposes innovative ideas for optimizing the armchair's design. First, an empirical study was conducted to comprehensively understand the classification of Ming-style round-backed armchairs’ structure to develop a 3D model. Secondly, an experimental research method was then employed to explore the parameters of laminated bamboo lumber for future studies. Additionally, a validation experiment was conducted to compare real-world scenarios with simulations using finite element analysis in Ansys. Finally, finite element analysis was used to test the feasibility and application of laminated bamboo lumber in furniture design, focusing on the material’s mechanical properties. Results indicated that laminated bamboo lumber has excellent mechanical properties as furniture design materials, subsequently, using the optimized results, the use of 0.6319 kg of steel was successfully reduced by 23.68% to ensure the armchair’s stability. This provides a reference for the future compter-assist and standardized innovative design of Chinese armchair. By incorporating compter-assist design and lightweight optimization, it is possible to save materials and make more efficient use of resources, thereby contributing to sustainable development goals in the field of furniture design.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

This paper investigates the effect of innovative cross-sectional configurations on Low-Cost Bamboo Composite (LCBC) structural members. The study employs both experimental and numerical methods with different resin matrices and bamboo species. In this study, LCBC short columns are designed with different innovative cross-sectional configurations in an attempt to overcome the costly production processes of engineered bamboo. This approach uses bundles of bamboo, both in culm and strip forms. A compatible, environmentally responsible, and economically justifiable resin matrix is used to fabricate an LCBC member. The production of LCBC members does not necessitate highly advanced technology. This capability enables the production of LCBC members in custom-designed cross-sectional shapes and lengths. This study introduces the Russian doll (RD), Big Russian doll (BRD), Hawser (HAW), and Scrimber (SCR) cross-sectional configurations. Extra-large, large, medium, and small sizes of bamboo are employed. Synthetic Epoxy (EXP), a Bio-based Experimental soft filler (BE1), Bio-Epoxy (BE2), Furan-based (PF1) matrices are applied. Furthermore, Moso, Guadua, Madake, and Tali bamboo species are incorporated. The results of this study reveal that the most efficient cross-sectional configuration for compressive strength is the HAW configuration, closely followed by SCR configuration. LCBC members with bio-resins have shown excellent promise in competing in strength with those made with their synthetic counterparts. The theoretical and numerical modeling of the LCBC members showed excellent correlation with the experimental results which provides the capacity to design LCBC for engineering projects. The LCBC design can be further developed with more bamboo and less resin content.

The aroused quest to reduce the delay at interconnect level is the main urge of this paper to come across a configuration of Carbon Nanotube (CNT) bundle namely squarely packed bundle of composite CNTs. The approach, demonstrated in this paper, adapts the composite bundle to adopt for high speed Very Large Scale Integration (VLSI) interconnect with technology sizing down. To reduce the delay of the proposed configuration of composite CNT bundle, the behavioral change of Resistance (R), Inductance (L) and Capacitance (C) has been observed with respect to both width of the bundle and diameter of the CNTs in the bundle. Consequently, the performance of the modified bundle configuration is compared with previously developed configuration namely squarely packed bundle of dimorphic MWCNTs in terms of propagation delay and crosstalk delay at local, semiglobal and global level interconnect. The proposed bundle configuration is ultimately enacted as better one for 32nmand 16nmtechnology node and suitable for 7nmas well.

Nanocellulose (CNC) seems to be a promising surfactant, which, together with expandable graphite (EG), forms the essence of an effective natural-based fire retardant wood coating. In our research, the most suitable composition of the mixture was tested concerning good solubility, dispersion, and consistency. Favorable results were achieved with the formulation composed of a 4% CNC alkaline solution with 80 wt.% of selected EG. Subsequently, six different EG were used to prepare these wood fire retardant coatings. The effectiveness of treatments was verified using a test with a radiant heat source, where the test samples' relative weight loss, relative burning rate, and surface temperature during 600 sec were evaluated. All prepared formulations can be characterized as more or less equally effective. However, the best results were obtained with EG of GG 200 – 100 N, where the mass loss of the sample was 8.10 ± 1.24%. Very good results were also achieved by graphite 25 E + 180 HPH (8.70 ± 0.89%), which is similar to the previous one, even according to the microscopic assessment of the coating as well as the expanded layer. Graphite type 25 K + 180 (8.86 ± 0.65 %) shows the expanded layer's best cohesion, coating uniformity, and ease of application. The results of this work confirmed that the CNC coating itself has significant retardation effects.

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

This paper investigates, experimentally and numerically, the buckling behavior of innovative sustainable Low-Cost Bamboo Composite (LCBC) structural columns under compressive loading. The LCBC columns are manufactured from bamboo culms in combination with bio-based resins to form composite structural columns. Different LCBC cross-sectional configurations are investigated in this study including the Russian doll (RD), Big Russian doll (BRD), Hawser (HAW), and Scrimber (SCR). Extra-large, large, medium, and small sizes of bamboo are employed to form the proposed configurations. Two bio-based resins including one bio-epoxy and one furan-based resin, in addition to a soft bio-based filler and a synthetic epoxy resin are applied. The bamboo species used as the cast-in-place giant bamboo for all configurations include Moso, Guadua, and Tali. In addition to experimental testing of the slender LCBC short columns, finite element analysis (FEA) software ABAQUS is applied to model the composite columns and predict their behavior. A buckling analysis using static Riks method is carried out to determine the LBCB’s response to axial compressive loading. A model is calibrated using test results with various imperfections, accounting for the variable behavior of each bamboo specimen, to accurately predict the behavior of LCBC columns with different resin contents. Slender LCBC columns showed maximum stress at buckling up to 60 MPa, highlighting the potential of bio-based resins for structural applications. The study found that the samples with bio-epoxy resin (BE2) exhibited enhanced material stiffness when compared to with synthetic epoxy (EPX) and furan-based resin (PF1), while PF1 specimens demonstrated increased ductility. The BE2 samples showed strain hardening in their stress-strain behavior, and the PF1 samples exhibited a long plateau phase before reaching the maximum load. Among the specimens with Moso bamboo and BE2 resin, those with SCR and HAW configurations achieved the highest compressive strengths.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

Shape memory alloys (SMA) are becoming a more important factor in actuation technology. Due to their unique features, they bring the potential to safe weight, installation space and reduce energy consumption. The system integration of the generally small diameter NiTi wires is an important cornerstone for the emerging technology. Crimping, a common method for the mechanical and electrical connection of SMA wires, has several drawbacks when it comes to miniaturization and high force outputs. For high force applications for example, multiple SMA wires in parallel are needed to keep actuation frequencies high, while scaling up the actuation force. To meet these challenges, the proposed study deals with the development of a resistance welding process for manufacturing NiTi wire bundles. The wires are welded to sheet metal substrate, resulting in promising functional properties and high joint strengths. The welding process benefits from low cost, easy to control parameters and good automation potential. A method for evaluating the resistance welding process parameters is presented. With these parameters in place, a manufacturing process for bundled wire actuators is discussed and implemented. The welded joints are examined by peel tests, microscopy, and fatigue experiments. The performance of the manufactured bundle actuators is demonstrated by comparison to a single wire with the same accumulated cross-sectional area.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Estimating Forest growing stock volume (GSV) is crucial for forest growth and resource management, as it reflects forest productivity. National measurements are laborious and costly, however integrating satellite data such as optical, Synthetic Aperture Radar (SAR), and Airborne Laser Scanning (ALS) with National Forest Inventory (NFI) data and machine learning (ML) methods has transformed forest management. In this study, Random Forest (RF), Support Vector Regression (SVR), and Extreme Gradient Boosting (XGBoost) were used to predict GSV using Estonian NFI data, Sentinel-2 imagery, and ALS point cloud data. Four variable combinations were tested: CO1 (vegetation indices and LiDAR), CO2 (vegetation indices and individual band reflectance), CO3 (LiDAR and individual band reflectance), and CO4 (a combination of vegetation indices, individual band reflectance, and LiDAR). Across Estonia's geographical regions, RF consistently delivered the best performance. In the northwest (NW), RF achieved an R² of 0.63 and an RMSE of 125.39 m³/plot. In the southwest (SW), it achieved an R² of 0.73 and an RMSE of 128.86 m³/plot. In the northeast (NE), RF achieved an R² of 0.64 and an RMSE of 133.77 m³/plot, and an R² of 0.70 and an RMSE of 120.72 m³/plot was achieved in the southeast (SE). These results underscore RF's precision in predicting GSV across diverse environments, though refining variable selection and improving tree species data could further enhance accuracy.

The research focuses on the production of particleboards from the biomass of energetic willow (Salix viminalis L.) and energetic poplar (Populus spp.), aiming to explore their feasibility as sustainable materials for various applications. Energetic willow and energetic poplar are known for their rapid growth and suitability for energy production. They present an intriguing alternative as raw materials with added value for particleboard manufacturing. The study investigates the selected mechanical and physical properties of the produced particleboards, considering parameters such as density profile, bending strength, modulus of elasticity, water absorption, thickness swelling, and screw withdrawal resistance. During the research, the results were also compared between different mass shares of willow and poplar particles in the particleboards. The findings underscore the promising potential of willow and poplar-based particleboards as eco-friendly alternatives in the construction and furniture industries, contributing to resource efficiency and carbon emission reduction efforts.

The aim of the study was to identify limiting factors for reusing wood through the recycling of window frames by conducting research under fully controlled conditions. The research involved manufacturing new window frames, seasoning them, and then shredding them into wood particles to prepare a three-layer particleboard. The proportion of wood particles in recycling was 0, 5, 10, 25, 50, and 100 parts by weight of the manufactured particleboard. Mechanical property tests were conducted: modulus of elasticity (MOE) and modulus of rupture (MOR), internal bond (IB), screw withdrawal resistance (SWR), and physical properties: density profile (DP), thickness swelling (TS) after water immersion, water absorption (WA), as well as formaldehyde emission and total volatile organic compounds (TVOC) tests. The conducted research indicates a significant potential for utilising wood from this sector of the wood industry, particularly considering variants with a higher proportion of recycled wood. MOR and MOE results are most promising for variants above 50 parts by weight of recycled wood. Based on the results obtained, it is clear that the production process should be improved or the raw material modified to enhance the internal bonding of particleboard, as these results were the weakest. Thus, recycled wood from window joinery has the potential to be reincarnated as particleboard, which continues to be widely used in their production.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

This study investigates the compressive strength and workability of concrete incorporating coconut shells and bamboo strips as alternative aggregates. The research compares traditional concrete to concrete mixtures with varying percentages of coconut shells and bamboo strips. Specifically, the study examines the effects of adding 10% coconut shell, 10% bamboo strip, and a combination of 5% coconut shell and 5% bamboo strip by volume to the concrete mix, tested in both C20 and C30 grades. To prepare the materials, coconut shells and bamboo strips were first crushed and then sieved. The sieving process retained particles that passed through a 10mm sieve but were retained on a 4.7mm sieve. The primary focus of the experimental tests was on measuring the compressive strength of the resulting concrete mixtures. The findings indicate that concrete incorporating coconut shells showed moderate workability. In contrast, concrete with bamboo strips exhibited lower workability. Regarding compressive strength, the concrete mix containing a combination of 5% coconut shell and 5% bamboo strips demonstrated a reduction in strength compared to the control group of normal concrete. This research highlights the potential of using coconut shells and bamboo strips as sustainable alternatives in concrete construction. While the workability varies between the different materials, the results provide valuable insights into their suitability for specific applications. This encourages further exploration of eco-conscious building practices and the development of sustainable construction materials.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

Enormous quantities of softwood and hardwood tree bark are generated yearly in the pulp and woodworking industry. Chemical compounds which can be found in bark extracts have important biological properties and therefore a high potential for using in the production of special formulations. In the present study, extraction of Picea abies bark with organosolv solvents was investigated to achieve a high yield of desirable compounds. For the extraction four different solvent ratios of ethanol and water were applied. The temperature range of extraction was set between 40 and 100 °C and stirring velocity of 400 rpm. Extractions were performed with a solid/liquid ratio of 1:20. Yields of phenolics, flavonoids and tannins were determined using gallic acid for total phenolic content (TPC), quercetin for total flavonoid content (TFC) and tannic acid for total tannins content (TTC) as calibration compounds. Qualitative analysis of phenolic constituents was performed after their derivatization, by gas chromatography coupled with mass spectrometry identification. The total yield of bark extract of 14.75 wt.% was achieved by using an ethanol/water ratio of 50% (v/v) and a temperature of 100 °C. Gas chromatography results show 9 aromatic carboxylic acids as phenolic acids and quercetin and (+)-catechin as flavonoid compounds. Highest concentrations of TPC = 3.21 mg gallic acid equivalent/g, TCF = 0.62 mg quercetin equivalent/g and TTC = 0.84 tannic acid equivalent/g were determined at the same process conditions by photometric method. This study determined the conditions for organosolv extraction of useful compounds and suggests that some of extractives, e.g., taxifolin and rhamnetin presented in the spruce bark extracts, have antiviral (SARS-CoV-2) effects. Therefore, this warrants further evaluation of the antiviral properties of spruce bark constituents.

High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

The silver fir (Abies alba Mill.) is among the most valuable conifers in Europe for ecological and economic reasons. In the course of history, primarily in the 20th century, its share in stands has been declining due to ill-suited management practices, especially clear-cut management, air pollution, and wildlife-induced damage. Based on recent knowledge of fir ecology and population dynamics, small-scale shelterwood and selection management have been introduced in fir stands, which have also stabilized them. Fir is an essential species for maintaining high stability and biodiversity, especially on planosols and in waterlogged habitats. Due to its shade tolerance and environmental flexibility, particularly at higher altitudes, it can coexist very well with many tree species in mixtures, which can increase the productive potential of stands. It can form stands of heterogeneous structure, ranging from single to multi-layer to selection. For its successful natural regeneration, it is essential to reduce cloven-hoofed game and thus prevent bud browsing damage. On the other hand, fir is a species relatively resistant to bark stripping and the spread of secondary rot compared to Norway spruce (Picea abies [L.] Karst.). During global climate change, fir is expected to shift to higher elevations with sufficient precipitation, while in the southern part of its natural range or at lower elevations, outside water-influenced habitats, it is likely to decline. This paper essentially reviews the description and distribution of the species, its ecological requirements, threats and diseases, habitat and stand conditions, and close-to-nature forest management practices with emphasis on ongoing climate change.

This article challenges the assumption that journals and peer review are essential for developing, evaluating and disseminating scientific and other academic knowledge. It suggests a more flexible ecosystem, and examines some of the possibilities this might facilitate. The market for academic outputs should be opened up by encouraging the separation of the dissemination service from the evaluation service. Publishing research in subject-specific journals encourages compartmentalising research into rigid categories. The dissemination of knowledge would be better served by an open access, web-based repository system encompassing all disciplines. There would then be a role for organisations to assess the items in this repository to help users find relevant, high-quality work. There could be a variety of such organisations which could enable reviews from peers to be supplemented with evaluation by non-peers from a variety of different perspectives: user reviews, statistical reviews, reviews from the perspective of different disciplines, and so on. This should reduce the inevitably conservative influence of relying on two or three peers, and make the evaluation system more critical, multi-dimensional and responsive to the requirements of different audience groups, changing circumstances, and new ideas. Non-peer review might make it easier to challenge dominant paradigms, and expanding the potential audience beyond a narrow group of peers might encourage the criterion of simplicity to be taken more seriously - which is essential if human knowledge is to continue to progress.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

Upholstery nonwoven fabric is a waste product mainly generated during upholstered furniture production. The polyester composition makes it problematic to recycle and reuse this product. This study examined the manufacturing process of nonwoven fabric-reinforced plywood composites and their selected mechanical and physical properties. Nonwoven fabric was integrated between veneers bound with urea-formaldehyde resin to improve standard layered composites' mechanical and physical properties. Several board variants were produced, differing in the position of the nonwoven layers in the composite structure. The composites were evaluated for modulus of rupture (MOR), modulus of elasticity (MOE), and screw withdrawal resistance, among others. The results showed that the addition of nonwoven fabric significantly improved some properties. Variants with strategically placed nonwoven layers showed the highest performance increases. The results underscore the potential of nonwoven fabric as an effective reinforcing material, offering a path to developing high-performance plywood composites suitable for demanding applications. Another, environmental profit is that the nonwoven fabric waste, that was used in tested plywood production, has not been subjected burning nor landfilling, but, by incorporation to plywood structure, have positively contributed to Carbon Capture and Storage (CCS) policy. The findings advocate for a circular economy approach, where industrial waste is effectively repurposed, contributing to the development of green materials in the wood-based composite industry.

Recycling upholstery textiles is challenging due to the complexity of materials, which often include a mix of fabrics, foams, and adhesives that are difficult to separate. The intricate designs and layers in upholstered furniture make it labor-intensive and costly to dismantle for recycling. Additionally, contaminants like stains, finishes, and flame retardants complicate recycling. Despite these difficulties, recycling upholstery textiles is crucial to reducing landfill waste and conserving resources by reusing valuable materials. It also helps mitigate environmental pollution and carbon emissions associated with producing new textiles from virgin resources. The presented research aimed to establish the feasibility of incorporating textile fibers from waste artificial leather fibers from the upholstery furniture industry into the structure of high-density fiberboards. This approach positively contributes to carbon capture and storage (CCS) policy and mitigates the problem of such waste being sent to landfills. The research shows that while selected mechanical and physical parameters of the panels decrease with a rising content of recycled textile fibers, it is possible to meet proper European standard requirements by adjusting technological parameters such as nominal density.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

Synaptopodin 2-like protein (SYNPO2L) is localized in the sarcomere of cardiomyocytes and is involved in heart morphogenesis. However, the molecular function of SYNPO2L in the heart is not fully understood. We investigated the interaction of SYNPO2L with sarcomeric alpha-actinin and actin filaments in cultured mouse cardiomyocytes. Immunofluorescence studies showed that SYNPO2L colocalized with alpha-actinin and actin filaments at the Z-discs of the sarcomere. Recombinant SYNPO2La or SYNPO2Lb caused bundling of actin filaments in the absence of alpha-actinin and enhanced alpha-actinin-dependent formation of actin bundles. In addition, high-speed atomic force microscopy revealed that SYNPO2La directly bound to alpha-actinin via its globular ends. The interaction between alpha-actinin and SYNPO2La stabilized the two proteins on actin filaments. These results strongly suggest that SYNPO2L cooperates with alpha-actinin during actin bundle formation to facilitate sarcomere formation and maintenance.

Recently, the concept of participatory democracy developed in the early 1970s has come back into fashion to revitalize the public involvement in political decision-making processes. Public par-ticipation in forest policy has been fully conceptualized by the scientific community in the late 1990s and early 2000s, but in many contexts the practical application remains unfulfilled. The aim of this study is to identify and analyze the participatory techniques used in literature to increase knowledge and facilitate its transferability into forest policies and strategies. A literature review was carried out to offer an overview of the participatory techniques adopted in the deci-sion-making process. At the end of literature review, 25 participatory techniques were identified based on over 2,000 publications. Afterwards, the participatory techniques were assessed using seven indicators (degree of participation, type and number of participants, time scale, cost, po-tential influence on policy). The results showed that the type of actors involved in the participa-tory technique is a key variable for the complexity and usefulness of the process, while the number of participants influences how information is disseminated. The Principal Component Analysis highlighted that the participatory techniques can be divided in three groups: the first group includes those techniques with a high degree of participation and a contextual high po-tential influence on policies, the second one includes techniques with a costs in terms of re-sources, while the third one consists of those with a large number of participants and reduced time requirements.

Autonomous weapons systems (AWS), sometimes referred to as “killer robots”, are receiving evermore attention, both in public discourse as well as by scholars and policymakers. Much of this interest is connected with emerging ethical and legal problems linked to increasing autonomy in weapons systems, but there is a general underappreciation for the ways in which existing law might impact on these new technologies. In this paper, we argue that as AWS become more sophisticated and increasingly more capable than flesh-and-blood soldiers, it will increasingly be the case that such soldiers are “in the power” of those AWS which fight against them. This implies that such soldiers ought to be considered hors de combat, and not targeted. In arguing for this point, we draw out a broader conclusion regarding hors de combat status, namely that it must be viewed contextually, with close reference to the capabilities of combatants on both sides of any discreet engagement. Given this point, and the fact that AWS may come in many shapes and sizes, and can be made for many different missions, we argue that each particular AWS will likely need its own standard for when enemy soldiers are deemed hors de combat. We conclude by examining how these nuanced views of hors de combat status might impact on meaningful human control of AWS.

The peptide hormone kisspeptin attenuates liver steatosis, metabolic dysfunction-associated stea-tohepatitis (MASH) and fibrosis in mouse models, by signaling via the kisspeptin 1 receptor (KISS1R). However, whether kisspeptin impacts fibrogenesis in the human liver is not known. We investigated the impact of a potent kisspeptin analog (KPA) on fibrogenesis using human precision cut liver slices (hPCLS) from fibrotic livers from male patients, in human hepatic stellate cells (HSCs), LX-2 and in primary mouse HSCs. In hPCLS, 48 h and 72 h of KPA (3 nM, 100 nM) treatment decreased collagen secretion, and lowered expression of fibrogenic and inflammatory markers. Immunohistochemical studies revealed that KISS1R is expressed and localized to HSCs in MASH/fibrotic livers. In HSCs, KPA treatment reduced transforming growth factor beta (TGFb)-induced expression of fibrogenic and inflammatory markers, in addition to decreasing TGFb induced collagen secretion, cell migration, proliferation and colony formation. Mechanistically, KISS1R signaling downregulated TGFb signaling by decreasing SMAD2/3 phosphorylation, via activation of protein-phosphatases PP2A, that dehosphorylates SMAD 2/3. This study revealed for the first time that kisspeptin reverses human hepatic fibrogenesis thus identifying it as a new therapeutic target to treat hepatic fibrosis.

Finishing coatings in the wood-based composites industry not only influence the final appearance of the product but also serve to protect against fungi, and molds, and reduce the release of harmful substances, particularly formaldehyde and volatile organic compounds (VOCs). Carbon-rich materials, such as those derived from birch bark extraction, specifically suberin acids, can fulfil this role. Previous research has demonstrated that adding suberin acid residues (SAR) at 20% and 50% by weight significantly enhances the gas barrier properties of surface finishing materials based on poly(lactide) (PLA) and polycaprolactone (PCL), particularly in terms of Total VOC (TVOC) and formaldehyde emissions. This study aims to explore whether these properties can be further improved through the incorporation of nano-zinc oxide (nano-ZnO). Previous research has shown that these nanoparticles possess strong resistance to biological factors and can positively affect the characteristics of nanofilms applied as surface protection. The study employed PLA and PCL finishing layers blended with SAR powder at 10% w/w and included 2% and 4% nano-zinc oxide nanoparticles. The resulting blends were milled to create a powder, which was subsequently pressed into 1 mm thick films. These films were then applied to raw particleboard surfaces. TVOC and formaldehyde emission tests were conducted. Additionally, the fungal resistance of the coated surfaces was assessed. The results showed that PLA/SAR and PCL/SAR composites with the addition of nano-zinc oxide nanoparticles exhibited significantly improved barrier properties, offering a promising avenue for developing biodegradable, formaldehyde-free coatings in the furniture industry with enhanced features. Furthermore, by utilizing SAR as a post-extraction residue, this project aligns perfectly with the concept of upcycling.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Sterile alpha motif domain-containing protein 9 (SAMD9) is a regulatory protein centrally involved in cell proliferation and apoptosis. Mapped to 7p21.1, variants in SAMD9 have been reported in <50 pediatric cases worldwide, typically with early lethality. Germline gain-of-function SAMD9 variants are associated with MIRAGE Syndrome (myelodysplasia, infection, restricted growth, adrenal hypoplasia, genital anomalies, and enteropathy). Spalt like transcription factor 1 (SALL1) is a zinc finger transcriptional repressor located at 16q12.1 where only two transcript variants in SALL1 are known. RUNX2 (6p21.1) encodes a nuclear protein with a Runt DNA-binding domain critical for osteoblastic differentiation, skeletal morphogenesis, and serves as a scaffold for nucleic acids and regulatory factors involved in skeletal gene expression. RUNX2 and SALL1 are thus both ‘master regulators’ of tissue organization and embryo development. Here, we describe exome sequencing and copy number variants in two previously unknown mutations—R824Q in SAMD9, and Q253H in SALL1. A new multiexon 3’ terminal duplication in RUNX2 is also reported. This is the first known phenotype characterization for the intersection of all three variants in a healthy 46,XX adult. Focusing on developmental progress, ultrastructural renal anatomy, and selected reproductive aspects, we describe this unique genotype diagnosed incidentally during Covid-19 illness. Individual disruption in SAMD9, RUNX2, or SALL1 would be expected to give a bleak prognosis. However, the convergence discovered here appears to dampen severe pathology, perhaps by cross-gene silencing of effects normally deleterious when such changes occur alone.

The first published description of intraovarian platelet-rich plasma (PRP) appeared in mid-2016, when a new experimental technique was successfully used in adult human ovaries to correct the reduced fertility potential accompanying advanced maternal age. Considering the potential therapeutic scope of intraovarian activated PRP and/or condensed platelet cytokines would likely cover both menopause treatment and infertility, the mainstream response has ranged from skeptical disbelief to welcome astonishment. Indeed, reports of restored menses in menopause (as an alternative to conventional hormone replacement therapy) and healthy term livebirths for infertility patients (either with IVF or as unassisted conceptions) after intraovarian PRP injection continue to draw notice. Yet any proper criticism of ovarian PRP applications will be difficult to rebut given the heterogenous patient screening, varied sample preparations, wide differences in platelet incubation and activation protocols, surgical/anesthesia techniques, and delivery methods. Notwithstanding these features, no adverse events have been reported thus far and ovarian PRP appears well tolerated by patients. Here, early research guiding the transition of ‘ovarian rejuvenation’ from experimental to clinical is outlined. Likely mechanisms are presented to explain results observed in both veterinary and human ovarian PRP research. Current and future challenges for intraovarian cytokine treatment are also discussed.

Bundle recommendation is provided to users by combining related items into a bundle, enhancing the user's shopping experience and increase the merchant's sales revenue. Despite the success of existing solutions based on Graph Neural Networks(GNN), there are still some significant challenges: (1)It is demanding to explicitly model multiple complex associations using standard graph neural networks. (2)Numerous additional nodes and edges are introduced to approximate higher-order associations. (3)The user-bundle historical interaction data is highly sparse. In this work, we propose a Global Structural Hypergraph Convolution model for Bundle Recommendation (SHCBR) to address the above problems. Specifically, we jointly incorporate multiple complex interactions between users, items, and bundles(three entities) into a relational hypergraph without introducing additional nodes and edges. Higher-order associations are already involved in the hypergraph structure which alleviate the training burden of neural networks and the dilemma of scarce data. In addition, we design a special matrix propagation rule that captures non-pairwise complex relationships between entities. Using item nodes as links, hypergraph convolution propagation between user and bundle nodes generates the learned representations. Experimental results on two real-world datasets demonstrate that SHCBR outperforms the state-of-the-art baselines by 11.07%-25.66\% on Recall and 16.81%-33.53% on NDCG. We publicly release the codes and datasets at https://github.com/Lxtdzh/SHCBR-master/.

The statistical bundle is the set of couples $(Q,W)$ of a probability density Q and a random variable W such that $\mathbb{E}$_Q [W] = 0. On a finite state space, we assume Q to be a probability density with respect to the uniform probability and give an affine atlas of charts such that the resulting manifold is a model for Information Geometry. Velocity and accelleration of a one-dimensional statistical model are computed in this set up. The Euler-Lagrange equations are derived from the Lagrange action integral. An example of Lagrangian using minus the entropy as potential energy is briefly discussed.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Involving local people in natural area management is very important to address the complexity of environmental management issues for sustainable use of local resources. Participatory methods require the contribution of local stakeholders in decision making. Mapping the environmental views of local communities allows for detecting aspects that could facilitate management efforts. This research – in the frame of the Skyros LIFE project and the PAMNATURA project - measures local acceptability of the conservation actions proposed by the LIFE project in Skyros Island (Greece) in relation with recording local people’s environmental orientation using the 15-item revised New Ecological Paradigm (NEP) scale. The research was carried out by means of questionnaires. The LIFE project proposed actions were grouped into three categories according to their theme, i.e. promoting (a) Nature protection, (b) Agro-pastoralism and (c) Ecotourism. The sample seems to largely agree with the LIFE project proposals, while the results showed high scores for most of the NEP scale items, implying pro-environmental beliefs, though there appears disagreement or neutrality regarding a few items. Local acceptability of the proposed actions was found to correlate to local people’s environmental concern measured through the NEP scale. Drawing on the results, implementation of actions related directly or indirectly to economic activities, preservation of traditional activities, as well as environmental education, interactive informing and consultation could enhance local participation. Skyros island seems to offer an appropriate social background for applying participatory and adaptive management and implementing conservation programs.

Understanding maturation stress and wood properties of poplar tension wood are critical for improving lumber yields and utilization ratio. In this study, Released Longitudinal Maturation Strains (RLMS), anatomical features, physical and mechanical properties, and nano-mechanical properties of the cell wall were analyzed at different peripheral positions and heights in nine inclined, 12-year-old poplar (Populus×euramericana ‘Zhonglin46’) trees. The correlations between RLMS and wood properties were determined. The results showed that there were mixed effects of artificial inclination on wood quality and properties. The upper sides of inclined stems had higher RLMS, proportion of G-layer, bending modulus of elasticity, and elastic modulus of cell wall but lower microfibril angle than the lower sides. At heights between 0.7 m and 2.2 m, only the double wall thickness increased with height, RLMS and other wood properties such as fiber length and basic density fluctuated or changed little with height. RLMS was a good indicator of wood properties in the tension wood area and at heights between 0.7 m and 1.5 m. The results of this study present opportunities to identify and select better quality wood in poplar trees.

Objectives: The promising specific growth regulators are employed tissue culture of the bamboo species. The specific natural hardening mixture supports the acclimatization and adaptation of the protected cultivation. The bamboo species contribute to the carbon sequestration and stabilization of the environment. Findings: The growth regulator 2, 4-D encourages callus induction and growth regulators NAA + TDZ, BAP + Kinetin + Gelrite, BAP + Kinetin + Coconut water + myo-inositol, NAA and TDZ impose plant regeneration in the Bambusa species. The growth regulator of 2,4-D, 2,4-D + Kinetin, 2,4-D + BA, 2,4-D + BAP and 2,4-D + NAA + BAP produces callus induction in the Dendrocalamus species. The growth regulator of TDZ, BA and IBA + Coumarin + Putrescine, BAP + GA3, NAA + Kinetin, BA + IBA, BA + Kinetin + NAA, NAA + Kinetin, Kinetin + IAA has facilitated shoot regeneration in the Dendrocalamus species with the specific period. The growth regulator of BA and TDZ; BAP + TDZ, IBA + Coumarin + Putrescine, BAP + GA3, NAA + Kinetin, BA + IBA, BA + Kinetin + NAA, NAA + Kinetin, Kinetin + IAA develops root regeneration with unambiguous time in the Dendrocalamus species. The growth regulator of BAP and Kinetin + BAP imposes shoot regeneration and IBA and IBA + Coumarin + sucrose conducts root regeneration in the edible bamboo. The natural hardening materials of cocopeat, vermicompost, perlite, cow dung, FYM, compost, soil & garden soil and humus soil, perlite, and FYM recommend in the acclimatization and adaptation of the Bambusa species and Dendrocalamus species respectively. Novelty: The standard growth regulators and hardening mixtures impose tissue culture, acclimatization and adaptation in the bamboo species. The bamboo species involves in managing carbon sequestration, biogeochemical cycle and the environment.

A composite is a material formed from the combination of two or more constituent materials through a non-homogeneous mixture. This research aims to determine the effect of volume fraction and fiber orientation angle of the hybrid polyester-ulin wood powder (Eusideroxylon zwageri)-wire mesh composite on bending strength. The bending test was conducted using ASTM D-790 standard with a three-point bending test method. The composite was made using the hand lay-up method with various compositions of particles and polyester. The results showed that the composition with less ulin wood powder and finer mesh size with a 45° wire mesh angle orientation had the highest bending strength and high deformation capability. The addition of wire mesh did not significantly increase the bending strength but could reduce the effect of decreased deformation capability.

Covid-19 has caused infections and deaths worldwide. While research in the field of Data Science has contributed good predictions of positive Covid-19 case numbers, this study's review of literature shows there is little research in the use of variants of the virus in predictions. We set out to define and evaluate novel variant features. We find that features relating to variant trends, thresholds and amino acid substitutions are especially powerful in two tasks. In the first task, predicting Covid-19 case numbers, accuracy improved from 71.53% without variant features to 82.12% with variant features. In the second task, predicting transmission severity of variants between two classes, we created a method to build some variable ensembles through selecting appropriate models that are generated with variant features. The test results showed that our ensembles are more accurate and reliable. One particular ensemble of 14 models correctly classified 90.91% of variants, outperforming other models including the popular Random Forest ensemble. In addition, as the variant features have represented more underlying information about Covid-19 pathophysiology, our ensemble methods use only a few data samples to achieve an accurate prediction. The ensemble of 14 models uses only 50 cases of each variant, an ability that could be exploited for early detection of highly infectious variants. These research findings may benefit public health professionals, policy makers, and the research community in the collective efforts to overcome this disease.

Powder Bed Fusion (PBF) is a type of Additive Manufacturing (AM) technology that builds parts in a layer-by-layer fashion out of a bed of metal powder via the selective melting action of a laser or electron beam heat source. The technology has become widespread, however the demand is growing for closed loop process monitoring and control in PBF systems to replace the open loop architectures that exist today. This paper demonstrates the simulated efficacy of applying closed-loop state estimation to the problem of monitoring temperature fields within parts during the PBF build process. A simplified LTI model of PBF thermal physics with the properties of stability, controllability and observability is presented. An Ensemble Kalman Filter is applied to the model. The accuracy of this filters’ predictions are assessed in simulation studies of the temperature evolution of various test parts when subjected to simulated laser heat input. The significant result of this study is that the filter supplied predictions that were about 2.5x more accurate than the open loop model in these simulation studies.

There are various types of charged particles in the space environment, which can cause different types of radiation damage to materials and devices, leading to on-orbit failures and even accidents of spacecraft. Developing lightweight and efficient radiation shielding materials is an effective approach to improve the inherent protection of spacecraft. The protective performance of different materials against proton and electron spectra in the Earth’s radiation belts is evaluated by Geant4 simulation. Based on the simulation results, suitable hardening components are selected to design composite materials, and B4C/PEEK composites with different B4C content were successfully prepared. Experimental results demonstrate that the simulated and experimental results for the electron, proton and neutron shielding performance of B4C/PEEK composites are consistent. These composites exhibit excellent radiation shielding capabilities against electrons, protons and neutrons, and the radiation protection performance improves with increasing B4C content in the B4C/PEEK composite materials.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

The Kenya Forestry Service permits rental of low-density national forest areas for use as common farmland, but public access to such areas is restricted to prevent deforestation against a background of rising demand for fuel wood. This study was conducted to clarify characteristics relating to the production of indigenous bamboo (a useful wood resource) by the approximately 23% of locals who work on common farmland in central Kenya’s Kamae forest management area, with estimation to determine above-ground biomass. The results showed that bamboo still represents 60% of such biomass, indicating sustainability in the industry.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

Fusarium species are agriculturally important fungi with a broad host range and can be found as endophytic, pathogenic, or opportunistic parasites in many crop plants. This study aimed to identify Fusarium species in bare-rooted, dormant plants in Turkish grapevine nurseries using molecular identification methods and assess their pathogenicity. Asymptomatic dormant plants were sampled from grapevine nurseries (43) in different regions of the country, and fungi were isolated from plant roots and internal basal tissues. The Fusarium isolates were identified by performing gene sequencing (TEF1-α, RPB2) and phylogenetic analyses. Pathogenicity tests were carried out by inoculating mycelial agar pieces of isolates onto the stem or conidial suspensions into the rhizosphere of vines (1103 Paulsen rootstock). Laboratory tests revealed that Fusarium species were highly prevalent in Turkish grapevine nurseries (41 out of 43). Gene sequencing and phylogenetic analyses unraveled that 12 Fusarium species (F. annulatum, F. brachygibbosum, F. clavum, F. curvatum, F. falciforme, F. fredkrugeri, F. glycines, F. nanum, F. nematophilum, F. nirenbergiae, F. solani, and Fusarium spp.) existed in the ready-to-sale plants. Some of these species (F. annulatum, F. curvatum and F. nirenbergiae) consistently caused wood necrosis of seedling stems, rotting of the basal zone and roots, and reduced root biomass. Although the other nine species also caused some root rot and root reduction, their virulence was not as severe as the pathogenic ones, and they were considered opportunistic parasites or endophytic species. This study is the first detailed investigation of Fusarium species in grapevine nurseries in Türkiye and emphasizes the need to consider pathogenic species in producing healthy grapevine seedlings.

Nanomaterials have shown significant promise for enhancing the performance of composite materials and increasing their functionality for various industrial applications. This review explores the unique properties of nanomaterials, particularly carbon-based nanomaterials, and provides key findings in utilizing them to enhance composite performance. It highlights specific nano-based composite materials and their significant potential in advancing the field of nanocomposites. Challenges associated with nanocomposite production and utilization are also discussed, along with possible solutions to address them. Finally, the study provides recommendations for continued research and innovation in nanocomposites to fully unlock the benefits of these advanced materials for broader future applications.

In this paper, a novel microwave catalyst Ni@SiC/CNFs (NSC), C/Ni (NC), and C/SiC (SC) were successfully synthesized by electrostatic spinning method, and proved to degrade methylene blue with high efficiency under microwave irradiation. The results imply that the catalyst Ni@SiC/CNFs with double shell structure gave a 99.99 % removal rate in 90 s for the degradation of methylene blue under microwave irradiation, outperformed the C/Ni and C/SiC and most other reported catalysts in similar studies. On the one hand, the possible mechanism of the methylene blue degradation should be ascribed to that double shell structure increases the polarization source of the material, resulting in excellent microwave absorption properties; and on the other, the in-situ generation of active species OH• and O2 - under microwave radiation and the synergistic coupling effect of metal plasma greatly improved the degradation efficiency of methylene blue. The findings of this study could provide a valuable reference for the green degradation of industrial dye wastewater and its sustainable development process.

Passive microwave measurements have been available on satellites dating back to the 1970s on research satellites flown by the National Aeronautics and Space Administration (NASA). Since then, several other sensors have been flown to retrieve hydrological products for both operational weather applications (e.g., the Special Sensor Microwave/Imager–SSM/I; the Advanced Microwave Sounding Unit–AMSU) and climate applications (e.g., the Advanced Microwave Scanning Radiometer–AMSR; the Tropical Rainfall Measurement Mission Microwave Imager–TMI; the Global Precipitation Mission Microwave Imager–GMI). Here the focus is on measurements from the AMSU-A, AMSU-B and Microwave Humidity Sounder (MHS). These sensors have been in operation since 1998 with the launch of NOAA-15, and are also on board NOAA-16, -17, -18, -19 and the MetOp-A and -B satellites. A data set called the “Hydrological Bundle” is a Climate Data Record (CDR) that utilizes brightness temperatures from Fundamental CDRs to generate Thematic CDRs (TCDR). The TCDR’s include: Total Precipitable Water (TPW), Cloud Liquid Water (CLW), Sea-Ice concentration (SIC), Land surface temperature (LST), Land surface emissivity (LSE) for 23, 31, 50 GHz, rain rate (RR), snow cover (SC), ice water path (IWP), and snow water equivalent (SWE). The TCDR’s are shown to be in general good agreement with similar products from other sources such as the Global Precipitation Climatology Project (GPCP) and the Modern-Era Retrospective Analysis for Research and Applications (MERRA-2). Because of the careful intercalibration of the FCDR’s, little bias is found among the different TCDR’s produced from individual NOAA and MetOp satellites, except for normal diurnal cycle differences.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

The increasing demand for large-scale, high-frequency environmental monitoring has driven the adoption of satellite-based technologies for effective forest management, especially in the context of climate change. This study explores the potential of SAR for estimating the mass of harvesting residues, a significant component of forest ecosystems that impacts nutrient cycling, fire risk, and bioenergy production. The research hypothesizes that while the spatial distribution of residues remains stable, changes in moisture content—reflected in variations in the dielectric properties of the woody material—can be detected through SAR techniques. Two models, generalized linear model (GLM) and random forest (RF), were used to predict the mass of residues using interfer-ometric variables (phase, amplitude and coherence) as well as the backscatter signal from several acquisition pairs. The models provided encouraging results (R2 of 0.48 for GLM and 0.13 for RF), with acceptable bias and RMSE. We concluded that SAR data are feasible to predict the mass of harvesting residues and the findings could lead to improved monitoring and management of forest residues, contributing to sustainable forestry practices and enhanced bioenergy resource utilization.

Shape Memory Polymer (SMP) actuators are smart materials that adapt and switch shape in response to environmental conditions, allowing controlled and dynamic building systems. The integrated SMP strip enabled the adaptive facade shading system to operate independently and with flexibility under certain thermoresponsive conditions to regulate building performance. This study aims to improve adaptive façade performance in a hot-humid climate by determining optimal thermal activation factors for the shape memory polymer. This was achieved by comprehensively examining and analysing the impact of various SMP activation parameters on energy efficiency, thermal comfort, and visual comfort. In addition, dynamic IES-VE building energy simulation was used to evaluate the thermal performance of the adaptable facade. The results were validated using a multicriteria approach to compare with the existing glass façade of a high-rise apartment. The results showed that the coactivation technique, which combines solar radiation and air temperature triggers, proved to be the most efficient strategy to improve the performance of the adaptive façade. This strategy minimised heat gain, lowered indoor temperatures, reduced glare, and enhanced daylight comfort, resulting in notable energy savings through reduced cooling consumption. The study concluded that the utilisation of SMP actuators with fine-tuning activation parameters significantly optimised adaptive façade performance, promoting functionality, efficiency, and sustainability in buildings.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

CO2 emission activity of xylotrophic fungi response to an increase in temperature in the range of 10-30 °C on the example of pure dikaryotic cultures of Fomes fomentarius s. str., F. inzengae, Fomitopsis betulina, F. pinicola, Phellinus igniarius was analyzed. Emission activity was assessed by the difference in CO2 concentration in 0.5-liter exposure chambers with Petri dishes with mycelium growing on agar at the beginning of exposure and an hour later using a Gasmet DX-4030 FTIR spectrometer (Gasmet Technologies Oy, Finland), error measurements ±50 ppm. Specific (μg CO2/cm2/h) and total (μg CO2/h) emission activity and its relationship with temperature and size (area) of the mycelium were assessed. It has been shown that in the range of 10-30 °C, the specific and total CO2 emission activity of the mycelium is closely and positively related to temperature. Specific emission, which is an indicator of the respiratory activity of the mycelium, does not depend on its size; its only driver is temperature, the relationship with which is linear: an increase in temperature by 10 °C causes an increase in the specific emission activity of the mycelium by 1.7 times. The total CO2 emission activity, which is an indicator of the total amount of CO2 emitted, is directly proportional to the specific emission activity and the size of the mycelium. In the range of 10-30 °C, an increase in temperature causes an almost equal increase in both the specific emission activity of the mycelium (Q10 1.7) and its growth (Q10 1.5) and causes an exponential increase in the total emission of CO2. This must be taken into account when predicting CO2 emissions from woody debris under climate change, as it could potentially contribute to accelerating climate change.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

The electrokinetics methods have a great potential to characterize hydrogeological processes in geological media, especially in complex hydrosystems such as fractured formations. In this work, we conceptualize fractured media as a bunch of parallel capillary fractures following the fractal size distribution. This conceptualization permits to obtain analytical models for both the electrical conductivity and the electrokinetic coupling in water saturated fractured media. We explore two different approaches to express the electrokinetic coupling. First, we express the streaming potential coupling coefficient as a function of the zeta potential and then we obtain the effective charge density in terms of macroscopic hydraulic and electrokinetic parameters of porous media. We show that when the surface electrical conductivity is negligible, the proposed models reduces to the previously proposed one based on a bundle of cylindrical capillaries. This model opens up a wide range of applications to monitor the water flow in fractured media.

Based on the perspective of complex directed weighted network analysis, this paper constructs a static resilience evaluation framework for trade networks from two dimensions: structural resilience and node resilience. It studies the evolution of static resilience in the upstream, midstream, downstream, and recycling trade networks of global wood forest products from 2002 to 2021. The study finds that the total trade volume of global wood forest products has increased by 58.0%, 77.3%, 71.2%, and 77.2% in the upstream, midstream, downstream, and recycling sectors, respectively. The downstream trade network exhibits efficient information transmission and resource mobility capabilities. All four types of trade networks exhibit scale-free characteristics, with core countries such as China, the United States, and Germany playing a dominant role in the network and playing a crucial role in network robustness, but also increasing network vulnerability. In terms of unweighted assortativity, all four networks exhibit the characteristic of "small countries relying on hubs," while the weighted assortativity of the downstream network is positive, indicating enhanced network resilience. In terms of node resilience, countries exhibit significant differences and dynamic changes. China demonstrates strong resilience and adaptability, while the United States maintains its core position. China's influence in the downstream network has significantly increased, and India has rapidly emerged in the recycling network. To enhance network resilience, it is necessary to increase diversity and redundancy, establish effective emergency response mechanisms, and promote the diversification and green transformation of the supply chain.

This brief review highlights some current issues in Galactic stellar nucleosynthesis, and some recent laboratory studies by the Wisconsin atomic physics group that have direct application to stellar spectroscopy, in order to advance our understanding of the chemical evolution of our Galaxy. The relevant publication history of the lab studies are summarized, and investigations into the abundances of neutron-capture and iron-peak elements in low metallicity stars are described. Finally, new initatives in near-infrared spectroscopy are briefly explored.

This study aims to investigate the effects of cement kiln dust (CKD) on the hydration reactions and mechanical properties of cement and to evaluate its potential for use as a supplementary cementitious material (SCM). The key variables are the CKD type and incorporation rate. Cement paste and mortar specimens containing CKD were prepared to examine their effects on the cement hydration and mechanical properties. The impact on hydration was assessed using setting time measurements, heat of hydration tests, and thermogravimetric analysis (TG). In addition, compressive strength tests were conducted to evaluate the effect of CKD on the mechanical properties of the cement. The results indicated that CKD promoted early cement hydration and enhanced the early age mechanical properties. However, owing to its lack of pozzolanic reactivity, it did not significantly affect long-term hydration. Given that the effects of CKD vary slightly depending on its chemical composition, careful consideration of CKD's properties suggests that its potential use as a SCM is promising.

While bamboo's sustainability and impressive mechanical properties make it suitable for structural use, its application is hindered by challenges in connection systems. Bamboo's hollow, thin-walled nature, dimensional variations, and anisotropic properties complicate connection design. Despite numerous studies and proposed connection types, a consensus on preferred bamboo connections remains elusive. Ideal connections for raw bamboo structures should be robust, economical, practical, simple, and easy to assemble. This paper reviews 62 scientific papers from the Scopus database published between 2003 and 2024, along with additional relevant references. It identifies research gaps, recommending further studies on bamboo connections considering factors like species, harvest age, treatment type, and node location. Analysis of failure modes and long-term behavior is essential to anticipate and mitigate risks associated with bamboo connections, ensuring durability, and minimizing maintenance needs. Lastly, developing universally accepted standards and codes for bamboo and bamboo connections is crucial for widespread adoption in the construction industry.

Bamboo is the building material of the past and future. It offers numerous properties that make it versatile for various applications, including construction. Its impressive strength-to-weight ratio enables it to bear substantial loads and stresses, while its good elasticity allows efficient energy absorption. However, its mechanical properties can vary based on factors such as species, age, locations, methods, and treatment. Treating bamboo is essential to enhance its properties and durability. The literature provides various natural and chemical treatments which enhanced some of the properties but also reported a drawbacks on higher temperature, content and duration. This paper reviewed 57 articles from Scopus database, specifically focusing on article-document type publications from the years 2003 to 2023. Additional references were also incorporated to address concerns in properties, treatment and standards to provide systematic understanding. MATLAB was utilized for data text analytics. With extensive assessment on the articles, the following gaps and concerns were observed and recommends for further study and assessment such as for bamboo properties, the development of centralized guidelines and procedures for the preparation and processing; exploration of alternative materials to reinforce bamboo without compromising its ductility; development of joint connections, and testing of mechanical properties considering seismic, wind and vibration. For treatment methods, the standardization of procedures using natural, chemical or combination. Lastly, for bamboo codes and standards, assessment of existing codes and standards for testing the mechanical properties of bamboo highlighting the potential limitations and areas, uniformity, differences with all existing similar standards. By filling these gaps, it can support the reliability and robustness of bamboo as a sustainable material, fostering its promotion and adoption in construction industry.

Bamboo plastic composites have become a hot research topic and a key focus of research. However, the many strong, polar, hydrophilic hydroxyl groups in bamboo flour (BF) results in poor interfacial compatibility between BF and hydrophobic polymers. Maleic anhydride-esterified (MAH-e-BF) and lactic acid-esterified bamboo flour (LA-e-BF) were prepared using an in situ solid-phase esterification method with BF as the raw material and maleic anhydride or lactic acid as the esterifying agent. Fourier transform infrared spectroscopy results confirmed that BF esterification with maleic anhydride and lactic acid was successful, with the esterification degrees of MAH-e-BF and LA-e-BF at 21.04 and 14.36%%, respectively. Esterified BF was characterized by scanning electron microscopy, contact angle testing, X-ray diffractometry, and thermogravimetric analysis. The results demonstrated that esterified BF surfaces were covered with graft polymer and the surface roughness and bonding degree of MAH-e-BF clearly larger than those of LA-e-BF. The hydrophobicity of esterified BF was significantly higher than BF and the hydrophobicity of MAH-e-BF better than LA-e-BF. The crystalline structure of esterified BF showed some damage, with MAH-e-BF exhibiting a greater decrease in crystallinity than LA-e-BF. Overall, the esterification reaction improved BF thermoplasticity, with the thermoplasticity of MAH-e-BF appearing better than LA-e-BF.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

Variable-Angle Tow (VAT) laminates can improve straight fiber composites mechanical properties thanks to the application of curvilinear fibers. This characteristic allows to achieve ambitious objectives for design and performance purposes. Nevertheless, the wider design space and the higher number of parameters result in a more complex structural problem. Among the various approaches that have been used for VATs study, Carrera’s Unified Formulation (CUF) allows to obtain multiple theories within the same framework, guaranteeing a good compromise between the results accuracy and the computational cost. In this article, the linear buckling behavior of VAT laminates is analyzed through the extension of CUF 2D plate models within the Reissner’s Mixed Variational Theorem (RMVT). Results show that RMVT can better approximate the prebuckling non-uniform stress field of the plate when compared to standard approaches, thus improving the prediction of the linear buckling loads of VAT composites.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

In previous work (Z. Angew. Math. Phys. 68(2), 2017), Apalara considered a one dimensional thermoelastic laminated beam under Cattaneo’s law of heat conduction and proved the exponential and polynomial decay results depend on the stability number χ_T . In this paper, we continue to study the same system and show that the solution of the concerned system lacks of exponential decay result in the case χ_T ≠ 0 which solves the open problem proposed by Apalara (Z. Angew. Math. Phys. 68(2), 2017).

Soft pneumatic actuators/robotics have received significant interest in the medical and health fields, due to their intrinsic elasticity and simple control strategies enabling desired interaction. However, current soft hand pneumatic exoskeletons often exhibit uniform deformation, mismatch the profile of the interacted objects, and seldom quantify the assistive effects during activities of daily life (ADL), such as extension angle and joint stiffness predicted. The lack of quantification poses challenges to the effective and sustainable advancement of rehabilitation technology. This paper introduces the design, modeling, and testing of pneumatic bioinspired Segmented Composite Proprioceptive Bending Actuators (SCPBAs) for hand rehabilitation in ADL tasks. The actuator’s soft-joint/rigid-bone segmented structure, inspired by the human finger anatomy, provides a superior fit compared to traditional continuous structures. A quasi-static model is established to predict the bending angles based on geometrical parameters. The SCPBAs also include a quantitative evaluation of joint stiffness and extension angle utilizing proprioceptive bending information. Additionally, a soft under-actuated hand exoskeleton equipped with SCPBAs demonstrates its potential in ADL rehabilitation scenarios.

Japanese plum tree (Prunus salicina Lindl.) is mainly cultivated in temperate areas of China and some European countries. Certain amounts of wood (from pruning works) are generated every year from this crop of worldwide commercial significance. The main objective of this work was to value this agricultural woody residue, for which the chemical composition of pruning wood extracts from six Japanese plum cultivars was investigated, and the antiproliferative activity of extracts and pure phenolics present in those extracts was measured. For the chemical characterization, total phenolic content and DPPH radical-scavenging assays and HPLC‒DAD/ESI‒MS analyses were performed, the procyanidin (‒)-ent-epicatechin-(2α→O→7,4α→8)-epicatechin (5) and the propelargonidin (+)-epiafzelechin-(2β→O→7,4β→8)-epicatechin (7) being the major components of the wood extracts. Some quantitative differences were found among plum cultivars, and the content of proanthocyanidins ranged from 1.50 (cv. ‘Fortune’) to 4.44 (cv. ‘Showtime’) mg/g of dry wood. Regarding the antitumoral activiy, eight wood extracts and four phenolic compounds were evaluated in MCF-7 cells after 48 h of induction, showing the wood extract from cv. ‘Songold’ and (‒)-annphenone (3) the best antiproliferative activity (IC50: 424 ppm and 405 ppm, respectively).

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

With the increasing of China's international status and the acceleration of the process of global economic integration, the internationalization strategy of Chinese enterprises is getting deeper and deeper. This paper analyzes the problems and challenges faced by the international supply chain management of Chinese bamboo weaving and creative products, and puts forward a set of supply chain management model that ADAPTS to the international development. Firstly, the concept, connotation and types of supply chain management are sorted out through literature review. Secondly, this paper analyzes the current situation of international supply chain management of bamboo editing and creative products, and points out the existing problems. Thirdly, based on the theory and practice of international supply chain management, this paper puts forward a set of supply chain management model suitable for the international development of bamboo editing and creative products. Finally, taking a bamboo weaving and creative products enterprise as an example, the application effect of the supply chain management model is empirically analyzed. The results show that the supply chain management model can effectively reduce the cost and improve the efficiency, and is conducive to the international development of bamboo editing and creative products.

In this study, 3-trimethoxy-silylpropane-1-thiol (MPTMS) was used as a surface modifier for Al2O3 powder to systematically analyze the effects of MPTMS concentration on the rheological properties, photocuring characteristics, and 3D printing performance of photocurable composite slurries. MPTMS concentration significantly influenced the rheological behavior of the slurry. Slurries containing 2 wt.% and 5 wt.% MPTMS exhibited a wide linear viscoelastic range (LVR). However, at concentrations of 10 wt.% and 20 wt.%, the LVR range narrowed, which led to reduced dispersion stability. In dispersion stability tests, the slurry with 2 wt.% MPTMS showed the most stable dispersion, while the 5 wt.% MPTMS concentration exhibited the highest photocuring rate. In 3D printing experiments, the 5 wt.% MPTMS concentration resulted in the most stable printed structures, whereas printing failures occurred with the 2 wt.% concentration. At 10 wt.% and 20 wt.%, internal cracking was observed, leading to structural defects. In conclusion, MPTMS forms silane bonds on the Al2O3 surface, significantly impacting the stability, rheological properties, and printing quality of Al2O3-acrylate composite slurries. An MPTMS concentration of 5 wt.% was found to be optimal, contributing to the formation of stable and robust structures.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

The concept of intelligence has many applications, such as coatings and cyber security. Smart coatings have the ability to sense and/or response to external stimuli and generally interact with their environment. Self-healing coatings represent a significant advance in improving material durability and performance using microcapsules and nanocontainers loaded with self-healing agents, catalysts, corrosion inhibitors, and water-repellents. These smart coatings can repair damage on their own and restore mechanical properties without external intervention and are inspired by biological systems. Properties that are affected by either momentary or continuous external stimuli in smart coatings can be related to corrosion, fouling, fungal, self-healing, pie-zoelectric, microbiological, etc. These coating properties can be obtained via combinations of either organic or inorganic polymer phases, additives and pigments. In this article, a review on the advancements of micro/nanocapsules for self-healing coatings is reported from the aspect of ex-trinsic self-healing ability. The concept of extrinsic self-healing coatings is based on the use of capsules or multichannel vascular systems loaded with healing agents/inhibitors. The outcome is that self-healing coatings exhibit improved properties compared to traditional coatings. It is mentioned that self-healing anticorrosive coating not only has enhanced passive barrier function, but also realizes active defense. As a result, there is a significant improvement of the service life and overall performance of the coating. Future research should be devoted to refining self-healing mechanisms and developing cost-effective solutions for a wide range of industrial applications.

Lucky bamboo (Dracaena sanderiana hort. ex Mast. = Dracaena braunii) is a domestic species widely cultivated for ornamental purposes in China. In March 2022, a severe occurrence of anthracnose disease was observed on the stems of lucky bamboo plants in a greenery retail store located in Nanjing, Jiangsu Province, China. The morphological characteristics of isolates obtained from diseased stem tissues were identical with those described for Colletotrichum species. Based on multilocus phylogenetic analysis with the internal transcribed spacer (ITS), actin (ACT) gene, and glyceraldehyde-3-phosphate dehydrogenase (GAPDH) gene, the pathogen was identified as Colleto-trichum gloeosporioides (Penz.) Penz. & Sacc. Pathogenicity was verified by mycelial plug-inoculating stem cuttings of one-year-old lucky bamboo plants and spray-inoculating whole one-year-old lucky bamboo plants, respectively. Koch’s postulates were fulfilled by the re-isolation of C. gloeosporioides from symptomatic tissues. To the best of our knowledge, this report describes the first time that C. gloeosporioides was observed to cause anthracnose on lucky bamboo in China.

Polyurethane (PU) foam adhesives were prepared from castor oil as a polyol with isocyanate poly (4,4′-methylene diphenyl isocyanate) (PMDI) using a solvent-free process. The NCO/OH molar ratio used for the preparation of PU foams was 1.5. Water, organosiloxane and dibutyltin dilaurate were blowing agent, surfactant and catalyst, respectively. Effects of the ratio of blowing agent and catalyst were adjusted to optimize the properties. The results show that 4 wt% of castor oil of catalyst and blowing agent minimizes water absorption and maximizes volume expansion in the PU foams. FT-IR analysis shows that urethane bond was formed by hydroxyl group of castor oil and –NCO group of isocyanate PMDI. More blowing agent and catalyst could improve the volume expansion ratio and reduce water retention of PU foams. It was found that Moso bamboo charcoal (Phyllostachys pubescens) or/and China fir wood particle (Cunninghamia lanceolate) composites with setting densities of 500 and 600 kg/m³ can be prepared from optimized castor oil-based PU foam adhesive at 100 °C for 5 min under a pressure of 1.5 MPa. Increasing the amount of bamboo charcoal decreases the equilibrium moisture content, water absorption and internal bonding strength of the composite. Notably, bamboo charcoal composite exhibits excellent dimensional stability. The optimized density and bamboo charcoal percentages of the composite were 500 kg/m³ and 50 to 100%. The castor oil-based PU composites containing bamboo charcoal fulfilled the CNS 2215 standards for particleboard. This dimensionally stable, low-density bamboo charcoal composite has high potential to replace current indoor building materials.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

A novel method of investigating the temperature dependent variation of aspects of the complex refractive index n* in samples in the THz range using continuous, non-polarised, synchrotron radiation is presented. The method relies on the use of ATR apparatus, and retains the advantage of minimal sample preparation, which is a feature of ATR techniques. The method demonstrates the viability of rapidly monitoring temperature reflectance whilst continuously heating or cooling samples by using a temperature variable Thermal Sample Stage. The method remains useful when the refractive index of the sample precludes attenuated total reflection study. This is demonstrated with the water reflectance experiments. The temperature dependent ATR reflectance of tissue-representative fats (lard and Lurpak® butter) was investigated with the novel approach. Both are within the ATR range of the diamond crystal in a “true” ATR mode. Lard showed no clear temperature variation between -15 0C and 24 0C at 0.7 to 1.15 THz or 1.70 to 2.25 THz. Lard can be regarded as having invariable, constant, dielectric properties within mixtures when biological substances are being assessed for temperature dependent dielectric variation within the stated THz ranges. Lurpak® butter (water content 14.7%) displayed temperature dependent reflectance features with a steady decline in reflectivity with increasing temperature. This is in line with the temperature-dependent behaviour of liquid water. There is no rapid change in reflectance, even at -20 0C, suggesting that emulsified water retains liquid-water-like THz properties at freezing temperatures.

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

Polyamide 11 (PA11) is a plant-based nylon made from castor beans. Powder bed fusion laser sintering (PBF-LS) is an additive manufacturing process used for PA11 which allows the reuse of the unsintered powder. The unsintered powder is mixed with virgin powders at different refresh rates which has been studied extensively for most semi-crystalline polyamides. However, there is lack of information on the effect of using 100% reused PA11 powder and the number of times it is reused on its own during powder bed fusion laser sintering. This paper investigates the effect of reusing PA11 powder in PBF-LS and number of times it is reused on the dimensional accuracy, density, thermal and tensile properties. From 100% virgin powder to 3rd use of the powder, there is a decrease in powder wastage, decrease in crystallinity and tensile strength. These was associated with the polymerisation and cross-linking process of polymer chains, upon exposure to high temperature. This results in a higher molecular weight and hence density. From the 4th use to 10th reuse, the opposite was observed which was associated to an increase in high-viscosity and un-molten particles which resulted in defects in the PBF-LS parts.

The continuous and precise mapping of glacier calving fronts is essential for monitoring and understanding rapid glacier changes in Antarctica and Greenland, which have the potential for significant sea level rise within the current century. This effort has been mostly restricted to the slow and painstaking manual digitalization of the calving front positions in thousands of satellite imagery products. Here, we have developed a machine learning toolkit to robustly and automatically detect glacier calving front margins in satellite imagery. The toolkit is based on semantic image segmentation using Convolutional Neural Networks (CNN) with a modified U-Net architecture to isolate the calving fronts from satellite images after having been trained with a dataset of images and their corresponding manually-determined calving fronts. As a case study we train our neural network on a varied set Landsat images with lowered resolutions from Jakobshavn, Sverdrup, and Kangerlussuaq glaciers, Greenland and test the results on novel images from Helheim glacier, Greenland to evaluate the performance of the approach. The neural network is able to identify the calving front in new images with a mean deviation of 96.3 m from the true fronts, equivalent to 1.97 pixels on average, while the corresponding error for manually-determined fronts on the same resolution images is 92.5 m. We find that the trained neural network significantly outperforms common edge detection techniques, and can be used to continuously map out calving-ice fronts with a variety of data products.

In this paper, we investigate the stabilization of a one-dimensional thermoelastic laminated beam with structural damping, coupled to a heat equation modeling an expectedly dissipative effect through heat conduction governed by Gurtin-Pipkin thermal law. Under some assumptions on the relaxation function g, we establish the well-posedness for the problem. Furthermore, we prove the exponential stability and lack of exponential stability for the problem. To achieve our goals, we make use of the semigroup method, the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem.

The automotive industry is increasingly adopting laminated glass in side and rear windows to comply with safety standards aimed at reducing ejection injuries. However, this trend may have unintended consequences for occupant rescue and escape in submerged vehicle incidents. As more vehicles incorporate laminated glass, concerns arise that they could become "glass coffins" in water, making it more difficult for occupants to exit or be rescued. The use of laminated glass is driven by Federal Motor Vehicle Safety Standard 226 (FMVSS 226) for ejection mitigation, but it does not address the risk of vehicle submersion and occupant drowning. Drowning accounts for a substantial portion of vehicle-related fatalities. As the adoption of laminated glass grows, there is a need for drowning prevention measures, such as automatic window opening systems, to mitigate the risk of vehicles becoming "glass coffins" in water. A comprehensive approach addressing both ejection and submersion dangers is necessary to maximize occupant protection and save lives.