We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Any quantization maps linearly functions on a phase space to symmetric operators in a Hilbert space. Covariant integral quantization combines operator-valued measure with symmetry group of the phase space. Covariant means that the quantization map intertwines classical (geometric operation) and quantum (unitary transformations) symmetries. Integral means that we use all ressources of integral calculus, in order to implement the method when we apply it to singular functions, or distributions, for which the integral calculus is an essential ingredient. In this paper we emphasize the deep connection between Fourier transform and covariant integral quantization when the Weyl-Heisenberg and affine groups are involved. We show with our generalisations of the Wigner-Weyl transform that many properties of the Weyl integral quantization, commonly viewed as optimal, are actually shared by a large family of integral quantizations.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

A century-old scientific conundrum is solved in this paper. The Prandtl mixing length modelled plane boundary turbulent flow is described by: $\frac{du^+}{d{y^+} }+\kappa^2{y^+} ^2\left( \frac{du^+}{d{y^+} }\right)^2=1$, together with boundary condition $ {y^+} =0:\, u^+=0$. Only an approximate solution to this nonlinear ordinary differential equation (ODE) has been sought so far, however, the exact solution to this ODE has not been obtained. By introducing a transformation, $2\kappa y^+=\sinh \xi$, I successfully find the exact solution of the ODE as follows: $u^+=\frac{1}{\kappa}\ln(2\kappa {y^+} +\sqrt{1+4\kappa^2{y^+} ^2})-\frac{2{y^+} }{1+\sqrt{1+4\kappa^2{y^+} ^2}}$.

We propose a method for creating parallel Bessel-like vortical optical needles with an arbitrary axial intensity distribution via superposition of different cone-angle Bessel vortices. We analyze the interplay between the separation of individual optical vortical needles and their respective lengths and introduce a super-Gaussian function as their axial profile. We also analyze the physical limitations to observe well-separated optic needles, as they are influenced by mutual interference of the individual beams. To verify our theoretical and numerical results, we generate controllable spatial arrays of individual Bessel beams with various numbers and spatial separations by altering the spectrum of the incoming laser beam via the spatial light modulator. We demonstrate experimentally how to implement such beams using a diffractive mask. The presented method facilitates the creation of diverse spatial intensity distributions in three dimensions, potentially finding applications in specific microfabrication tasks or other contexts. These beams may have benefits in laser material processing applications such as nanochannel machining, glass via production, modification of glass refractive indices, and glass dicing.

Purpose: To simplify the application of optical coherence tomography (OCT) for examination of subsurface morphology in the oral cavity and reduce barriers towards adoption of OCT as a biopsy guidance device. The aim of this work was to develop automated software tools for simplified analysis of the large volume of data collected during OCT. Methods: Imaging and corresponding histopathology were acquired in-clinic using a wide-field endoscopic OCT system. An annotated dataset (n = 294 images) from 60 patients (34 male, 26 female) was assembled to train four unique neural networks. A deep learning pipeline was built using convolutional and modified u-net models to detect the imaging field of view (network 1), detect artifacts (network 2), identify the tissue surface (network 3), and identify the presence and location of the basement membrane (network 4). Results: The area under the curve of the image and artifact detection networks was 1.00 and 0.94 respectively. The Dice similarity score for the surface and basement membrane segmentation networks was 0.98 and 0.83 respectively. Conclusion: Deep Learning (DL) techniques can identify the location and variations in the epithelial surface and basement membrane in OCT images of the oral mucosa. Segmentation results can be synthesized into accessible en face maps to allow easier visualization of changes.

There are given algebraic and integral identities for a pair or a triple of plane solenoidal fields. As applications, we obtain sufficient potentiality conditions for a plane vector field. The integral identities are also important for exact a priori estimates.

According to the standard cold dark matter (CDM) cosmology, the structure of dark halos including those of galaxy clusters reflects their mass accretion history. Older clusters tend to be more concentrated than younger clusters. Their structure, represented by the characteristic radius $r_s$ and mass $M_s$ of the Navarro-Frenk-White (NFW) density profile, is related to their formation time. In this study, we show that $r_s$, $M_s$, and the X-ray temperature of the intracluster medium (ICM), $T_X$, form a thin plane in the space of $(\log r_s, \log M_s, \log T_X)$. This tight correlation indicates that the ICM temperature is also determined by the formation time of individual clusters. Numerical simulations show that clusters move along the fundamental plane as they evolve. The plane and the cluster evolution within the plane can be explained by a similarity solution of structure formation of the universe. The angle of the plane shows that clusters have not achieved “virial equilibrium” in the sense that mass/size growth and pressure at the boundaries cannot be ignored. The distribution of clusters on the plane is related to the intrinsic scatter in the halo concentration--mass relation, which is originated from the variety of cluster ages. The well-known mass--temperature relation of clusters ($M_\Delta\propto T_X^{3/2}$) can be explained by the fundamental plane and the mass dependence of the halo concentration without the assumption of virial equilibrium. The fundamental plane can also be used for calibration of cluster masses.

The cytoskeleton is a master organizer of cell cortex, organelles positioning and membrane trafficking. Therefore, playing a decisive role in establishment of apico-basal polarity. Septins are critical cytoskeleton components which function in apico-basal polarity remain weakly investigated. Here, using 3D culture system, we demonstrate that septin9 localizes at basolateral membrane (BM). Its depletion induces an inverted polarity phenotype, decreasing -catenin at BM and increasing the expression of the transforming growth factor (TGF) and the epithelial-to-mesenchymal transition (EMT) markers. Similar effects were observed upon deleting its two polybasic domains, and the mutant become cytoplasmic and apical. The cysts with an inverted polarity phenotype display an invasive phenotype, with src and cortactin accumulating at the peripheric membrane. Inhibition of TGF-receptor and RhoA rescues the polarized phenotype. Although the cysts from overexpressed-septin 9, overgrowth and present a filled lumen. Both phenotypes correspond to tumor features. This suggests that septin 9 expression and assembly through the two PB domains are essential for establishing and maintaining apico-basal polarity against tumor development through a mechanism involving TGF-dependent EMT and RhoA activity.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

(1) Background: Breast cancer is a frequent heterogeneous disorder diagnosed in woman and is a high cause of mortality of them in reason to rapid metastasis and disease recurrence. Ferroptosis can inhibit breast cancer cell growth, improve the sensitivity of chemotherapy and radiotherapy and inhibit distant metastases so potentially acts on tumor micro-environment; (2) Methods: Ferroptosis/Extracellular matrix remodeling literature text-mining results were integrated in breast cancer transcriptome cohort according their distant relapse free survival (DRFS) under adjuvant therapy (anthracyclin+taxanes) and also in MDA-MB-231 transcriptome functional experiments with ferroptosis activations (GSE173905); (3) Results: Ferroptosis/Extracellular matrix remodeling text-mining identified 910 associated genes in at list 10 articles. Univariate Cox analyses censored on breast cancer (GSE25066) selected 252 individual significant genes and 171 of them found with an adverse expression. Functional enrichment of these 171 adverse genes predicted basal breast cancer signatures. By text-mining some ferroptosis significant adverse selected genes shared citations in domain of ECM remodeling such as: TNF, IL6, SET, CDKN2A, EGFR, HMGB1, KRAS, MET, LCN2, HIF1A, TLR4. A molecular score based on expression the eleven genes was found predictive of worst prognosis breast cancer at univariate level: basal subtype, short DRFS, high grade values 3 and 4, estrogen and progesterone receptors negative and nodal stages 2 and 3. This eleven gene signature was validated as regulated by ferroptosis inductors (erastin and RSL3) in triple negative breast cancer cellular model MDA-MB-231.; (4) Conclusions: Crosstalk between ECM remodeling-Ferroptosis functionalities allowed to define a molecular score which have been characterized as an independent adverse parameter in prognosis of breast cancer patients. Gene signature of this molecular score have been validated to be regulated by erastin/RSL3 ferroptosis activators. This molecular score could be promising to evaluate ECM impact of ferroptosis target therapies in breast cancer.

We present a high-throughput nanoindentation study of in-situ bending effects on incipient plastic deformation behavior of polycrystalline and single-crystalline pure aluminum and pure copper at ultra-nano depths (<200nm). We find that hardness displays a statistically inverse dependence on in-plane stress for indentation depths smaller than 10nm, and the dependence disappears for larger indentation depths. In addition, plastic noise in the nanoindentation force and displacement displays statistically robust noise features, independently of applied stresses. Our experimental results suggest the existence of a regime in FCC crystals where ultra-nano hardness is sensitive to residual applied stresses, but plasticity pop-in noise is insensitive to it.

Continuum robots play the role of end-effector in various surgical robots and endoscopic devices. The robots may be categorized as rigid or soft continuum robots (SCRs). While the SCRs have proven advantages such as safety and compliance, more research and development are required to enhance their capability for specific medical scenarios. This research aims at designing a soft robot considering concepts of geometric and kinematic similarities. The chosen application is a semi-invasive medical application known as Transesophageal Echocardiography (TEE), but the methodology can be implemented in other similar applications. Since established rigid carrier construction make use of principles we find as well embodied in vertebral spines, the paragon for soft robot solution can be the phylogenetic precursor of the spine, the Chorda dorsalis. The feasibility of fabrication of a soft endoscopic device derived from that paragon within a robotics laboratory was shown empirically by producing a three-segment pneumatic SCR. The kinematic model was proposed based on the method of transformation matrices, and an algorithm based on a self-organizing map (SOM) was proposed and applied to realize kinematic similarity. The simulation results indicate that the algorithm acting as an open-loop controller forces the soft robot tip to follow the desired path which in this case is the path of the rigid probe. It is concluded that the solution provides a soft robot that can surrogate and succeed the traditional rigid counterpart owing to size, workspace, and kinematics.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

To have a better protection, strong toughness and good flexibility, all lives and plants must have skins, similarly, all books should have covers. In this paper, considering interlayer friction as a perturbation, we formulate a hardcover-book-like laminated plates with internal friction. For a quasi-static problem, detail analysis on the bending response and energy dissipation are carried out for a three-point-supported plates. Our numerical investigations show that the hardcover is more essential than the core layers in terms of bending response, and the energy dissipation within per loading-unloading cycle can be made to vary by a considerable amount. The central goal of studying is not only to predict the bending deformation of the book-like-plates, but also as a representative case to help finding some clue on the universal behaviours of multilayered architectures with internal friction.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

Fusarium species are agriculturally important fungi with a broad host range and can be found as endophytic, pathogenic, or opportunistic parasites in many crop plants. This study aimed to identify Fusarium species in bare-rooted, dormant plants in Turkish grapevine nurseries using molecular identification methods and assess their pathogenicity. Asymptomatic dormant plants were sampled from grapevine nurseries (43) in different regions of the country, and fungi were isolated from plant roots and internal basal tissues. The Fusarium isolates were identified by performing gene sequencing (TEF1-α, RPB2) and phylogenetic analyses. Pathogenicity tests were carried out by inoculating mycelial agar pieces of isolates onto the stem or conidial suspensions into the rhizosphere of vines (1103 Paulsen rootstock). Laboratory tests revealed that Fusarium species were highly prevalent in Turkish grapevine nurseries (41 out of 43). Gene sequencing and phylogenetic analyses unraveled that 12 Fusarium species (F. annulatum, F. brachygibbosum, F. clavum, F. curvatum, F. falciforme, F. fredkrugeri, F. glycines, F. nanum, F. nematophilum, F. nirenbergiae, F. solani, and Fusarium spp.) existed in the ready-to-sale plants. Some of these species (F. annulatum, F. curvatum and F. nirenbergiae) consistently caused wood necrosis of seedling stems, rotting of the basal zone and roots, and reduced root biomass. Although the other nine species also caused some root rot and root reduction, their virulence was not as severe as the pathogenic ones, and they were considered opportunistic parasites or endophytic species. This study is the first detailed investigation of Fusarium species in grapevine nurseries in Türkiye and emphasizes the need to consider pathogenic species in producing healthy grapevine seedlings.

Inflammation is considered an important target for stroke therapy because it induces secondary brain damage after the initial ischemic insult. Peripheral monocytes migrate to the brain parenchyma after a central insult. They then differentiate to macrophages in a positive feedback fashion contributing to damage instead of ischemic resolution and inflammation control. A cyclic diterpenoid, (1S,2E,4R,6R,7E,11E)-cembra-2,7,11-triene-4,6-diol (4R), decreases neurodegeneration after ischemia with central anti-inflammatory activity. This study aims to determine whether the central anti-inflammatory effect of 4R is effective against peripheral inflammation triggered by brain ischemia. To investigate the anti-inflammatory effect of 4R, we treated macrophages with lipopolysaccharide (LPS) as an inflammatory model, followed by treatment with 4R. Microarray transcriptome analysis of over 30,000 genes identified the differential expression of 393 genes. Genes related to inflammation, cell adhesion, and transcription were validated with qPCR, and reduced expression was determined. Quantification of NF-kB phosphorylation served as a marker for the modulation of inflammation through gene transcription. Our results show that 4R was associated with a reduction in NFKB1 and ITGB5 gene expression, increased phosphorylation of NF-kB, and a decrease in macrophage adhesion in a blood-brain barrier model. These results indicate that 4R can partially modulate the peripheral immune response, making 4R a potential drug against post-ischemic inflammation.

The vertebrate basal ganglia are thought to play an important role in action selection—the resolution of conflicts between alternative motor programs. The effective operation of basal ganglia circuitry is also known to rely on appropriate levels of tonic dopamine transmission. We show that when the tonic level of simulated dopamine in a robotic model of the basal ganglia is significantly reduced or increased, relative to an effective operating baseline, a variety of behavioral outcomes are observed that provide interesting comparisons with the results of human and animal studies. The main findings were that progressive reductions in the levels of simulated dopamine caused a slowing of the robot’s movements and eventually an inability to initiate movement. These states were partially relieved at increased salience levels (stronger sensory/motivational input). Conversely, increased levels of simulated dopamine could cause distortion of the robot’s motor acts through partially-expressed motor activity relating to losing actions; this could also lead to increased frequency of switching between behaviors. Levels of simulated dopamine that were either significantly lower or higher than baseline could cause changes to the timing of behavior switching that could cause a loss of behavioral integration, sometimes leaving the robot in a ‘behavioral trap’. That some analogous traits are observed in animals and humans affected by dopamine dysregulation suggests that embodied (robotic) models could prove useful in understanding the role of dopamine neurotransmission in basal ganglia function and dysfunction. That the effects of simulated dopamine on robot action selection were partially, but not fully, predictable from the selection properties of the non-embodied basal ganglia model, also points to the added value of using robotic models to explore the relationship between brain activity and behavior.

Efficient management of basal cell carcinoma (BCC) requires reliable assessments of both tumors and post-treatment scars. We aimed to estimate image similarity metrics that account for BCC's perceptual color and texture deviation from perilesional skin. 176 clinical photographs of BCC were assessed by six physicians using a visual deviation scale. Internal consistency and inter-rater agreement were estimated using Cronbach's α, weighted Gwet's AC2, and quadratic Cohen's Kappa. The mean visual scores were used to validate a range of similarity metrics employing different color spaces, distances, and image embeddings from pre-trained VGG16 neural network. The calculated similarities were transformed into discrete values using ordinal logistic regression models. The Bray-Curtis distance in the YIQ color model and rectified embeddings from the 'fc6' layer minimized the mean squared error and demonstrated strong performance in representing perceptual similarities. Box plot analysis and Wilcoxon rank-sum test were used to visualize and compare the levels of agreement, conducted on a random validation round between the two groups: ‘Human-System’ and ‘Human-Human’. The proposed metrics were comparable in terms of internal consistency and agreement with human raters. The findings suggest that the proposed metrics offer a robust, and cost-effective approach to monitoring BCC treatment outcomes in clinical settings.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

Variable cross-section arch is widely used in practical engineering because of its beautiful arc and excellent mechanical properties. However, there is still no systematic and comprehensive study on the out-plane buckling of variable cross-section arch. In view of this, this paper is concentrated on an elastic analytical research of out-plane buckling of arches with variable cross-section under a uniformly distributed radial local load. The pre-buckling and out-plane buckling behaviour of a variable cross-sectional arch under an external load is quite different from that of an arch with uniform cross-section. The Castigliano's second theorem is used to establish pre-buckling force method equilibrium equations for variable cross-sectional arches under a uniformly distributed radial local load, and corresponding analytical solutions of normal stress, axial compression and the bending moment are obtained. Based on the energy method and the Ritz method, analytical solutions of the critical load for the elastic out-plane buckling of arches with variable cross-section are derived. Comparisons with ANSYS results indicated that the analytical solutions are able to accurately predict the pre-buckling internal forces and critical out-plane buckling load of variable cross-section arches subjected to a uniformly distributed radial local load. It is found that the internal forces and the out-plane buckling load of an arch are significantly affected by the variation of cross-sectional height. With the ratio of cross-sectional height of the top to the end increase, the bending moment decreases and the axial force and critical out-plane buckling load increase. Analytical solutions of pre-buckling internal force and critical out-plane buckling load problems for arches with variable cross-section have a wider significance, since they can provide an effective explicit analytic method for the optimal design of arch structure.

Probability is an open question in the ontological interpretation of quantum mechanics. It has been discussed in some trajectory interpretations such as Bohmian mechanics and stochastic mechanics. New questions arise when the domain of probability extends to the complex space, including the generation of complex trajectories, the definition of the complex probability, the relation of the complex probability to the real quantum probability, and so on. The complex treatment proposed here applies the optimal quantum guidance law to derive the stochastic differential (SD) equation governing the particle’s random motions in the complex plane. The ensemble of the complex quantum random trajectories (CQRTs) solved from the complex SD equation is used to construct the probability distribution ρc(t,x,y) of the particle’s position over the complex plane z=x+iy. The correctness of the obtained complex probability is confirmed by the solution of the complex Fokker-Planck equation. The significant contribution of the complex probability is that it can be used to reconstruct both quantum probability and classical probability, and to clarify their relationship. Although quantum probability and classical probability are both defined on the real axis, they are obtained by projecting complex probability onto the real axis in different ways. This difference explains why the quantum probability cannot exactly converge to the classical probability when the quantum number is large.

A focal plane array (FPA) detector was used for hyperspectral imaging in the infrared (IR) spectral region using thermal and synchrotron light sources. FPA Fourier-transform IR (FTIR) imaging microspectroscopy will be able to monitor real time changes at specific absorption bands when combined with high brightness synchrotron source. In this study, several types of samples with unique structural motifs were selected and used for assessing the capability of the FPA-FTIR imaging technique. It was shown that the time required for polariscopy at IR wavelengths can be substantially reduced by the FPA-FTIR imaging approach. By using natural and laser fabricated polymers with sub-wavelength features, alignment of absorbing molecular dipoles was revealed as well as higher order patterns (laser fabricated structures). Micro-spectroscopy of absorber orientation reveals alignment patterns even when they are not spatially resolved.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

This paper presents an exact solution to the Timoshenko beam theory (TBT) for first-order analysis, second-order analysis, and stability. The TBT covers cases associated with small deflections based on shear deformation considerations, whereas the Euler–Bernoulli beam theory (EBBT) neglects shear deformations. Thus, the Euler–Bernoulli beam is a special case of the Timoshenko beam. The moment-curvature relationship is one of the governing equations of the EBBT, and closed-form expressions of efforts and deformations are available in the literature. However, neither an equivalent to the moment-curvature relationship of EBBT nor closed-form expressions of efforts and deformations can be found in the TBT. In this paper, a moment-shear force-curvature relationship, the equivalent in TBT of the moment-curvature relationship of EBBT, was presented. Based on this relationship, first-order and second-order analyses were conducted, and closed-form expressions of efforts and deformations were derived for various load cases. Furthermore, beam stability was analyzed and buckling loads were calculated. Finally, first-order and second-order element stiffness matrices were determined.

The object of study is a transversely bent triangular plate made of orthotropic material fixed along the edges of the plate under the action of a uniformly distributed load. Fourth-order differential equilibrium equations with variable orthotropy parameters were used. The equations were approximated by finite differences for a grid of scalene triangles. This type of mesh accurately describes the boundary contour of the triangular-shaped plates. The boundary conditions for the mesh consider the orthotropy of the plate material. Seven standard finite-difference equations have been developed considering the boundary conditions along the three edges of the plate and the presence of three angles of an irregularly shaped triangle. A finite difference matrix is obtained. The matrix structure makes calculating a triangular plate at different base angles possible. The boundary conditions were varied in the form of rigid or hinged support of triangular plates. The calculation method considers the orthotropic parameters of the material in two mutually perpendicular planes. The adaptation of the numerical method to the calculation of orthotropic plates of arbitrary shape is described. Relationships are given for determining the rigidity characteristics of orthotropic materials. An algorithm for simple engineering calculation of triangular orthotropic plates is proposed, which makes it possible to perform accurate calculations in variant design.

This article aims to systematically review the available evidence concerning the relationship between basal metabolism (BM), body composition (BC), and physical activity (PA) with central obesity. The search strategy was carried out using Web of Science, PubMed, Google Scholar, and SciELO following the PRISMA guidelines. The STROBE checklist and the Jadad scale for quality assessment were also used. A total of 1382 studies were initially identified being 25 publications eligible for systematic data extraction. Individual studies showed that adults with waist circumference (WC) above 88 cm in women and above 102 in men had a higher risk of metabolic alterations related to high absolute energy expenditure and less maximum oxygen consumption (VO2 max). Participants with central obesity presented a high percentage of body fat (BF%) between 30.6% and 41.6%. Most of the PA intervention studies reported reductions in WC between 1.3 and 5.8 cm. In conclusion, there is a direct relationship between the components of BM with central obesity and a direct association between central obesity and BF%. PA is a protective factor that needs to be promoted to reduce WC and control central obesity as a public health problem. PROSPERO ID registration: CRD42021232917.

In humans, finely tuned gamma synchronization (60-90 Hz) rapidly appears at movement onset in a motor control network involving primary motor cortex, the basals ganglia and motor thalamus. Yet the functional consequences of brief movement-related synchronization are still unclear. Distinct synchronization phenomena have also been linked to different forms of motor inhibition, including relaxing antagonist muscles, rapid movement interruption and stabilizing network dynamics for sustained contractions. Here I will introduce detailed hypotheses about how intra- and inter-site synchronization could interact with firing rate changes in different parts of the network to enable flexible action control. The here proposed cause-and-effect relationships shine a spotlight on potential key mechanisms of cortico-basal ganglia-thalamo-cortical communication. Confirming or revising these hypotheses will be critical in understanding the neuronal basis of flexible movement initiation, invigoration and inhibition. Ultimately, the study of more complex cognitive phenomena will also become more tractable once we understand the neuronal mechanisms underlying behavioural readouts.

The basal ganglia (BG) are a central component of the brain, crucial to the initiation, execution and learning of adaptive actions. The BG are the major site of the action of dopamine. An important aspect of the BG architecture is the existence of two paths, direct and indirect, having different projection targets and dopamine receptor expression. To understand the BG, dopamine, and related disorders, it is imperative to understand the two paths. The standard account used in neuroscience research for decades posits that the role of the direct path is to support movements, while that of the indirect path is to suppress unselected or completed movements. This account is contradicted by converging evidence. Here, we explain why the arguments supporting the standard account are flawed, and present a new account, in which the role of the indirect path is completely opposite: to support automated execution. During acute events, the direct path allows coarse responses. These are refined by competition, and the resulting focused response is executed and learned by the indirect path, assisted by cholinergic interneurons and the subthalamic nucleus (STN). The new account allows a novel understanding of the symptoms of Parkinson's disease, in particular tremor and rigidity, and of its treatment by STN deep brain stimulation.

Abstract-Digital Phase Plane is presented in this paper. For constant input second order digital systems with arbitrary initial conditions for arbitrary quantizaters, this digital phase plane shows, in plot form, the state trajectory and the asymptotic stability, including the existence and the position of arbitrary period limit cycles.

In-plane electro-optical switching (IPS) is a natural feature of a conventional planar aligned display cell based on deformed helix ferroelectric liquid crystal effect (DHFLC-effect) with sub-wavelength helix pitch if the tilt angle close to 40 degrees.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

It is well known that the photon trajectories follow a curved path in a gravitational field. We explore here the gravitational bending of electric field lines. It seems that the electric field lines of a charge, supported in a gravitational field, follow exactly the trajectories of photons emitted isotropically from a source situated at the charge location. From a detailed examination of the electrostatic field of a charge accelerated uniformly in the instantaneous rest frame, exploiting the strong principle of equivalence, one can determine the bending of the electric field lines of a charge in a gravitational field. The fraction of electric field lines crossing a surface, stationary above or below the charge in the gravitational field, is shown to be exactly similar to the fraction of photon trajectories, emitted from a source placed at the charge location, intersecting that surface. On the other hand, for a freely falling charge in the gravitational field there is no such bending of electric field lines. The field lines continue to extend in radial straight lines from the instantaneous 'present' position of the charge, as do the trajectories of photons streaming away from the instantaneous position of a freely falling source in the gravitational field. The electric field configuration of a freely falling charge in the gravitational field is shown to be exactly the same as that of a charge moving uniformly in an inertial frame with velocity equal to the instantaneous ``present'' velocity of the freely falling charge.

Bending pipe is a common component of long distance pipeline. Accurately understanding the flow law of hydrate particles in elbow pipe is of great significance for optimizing pipeline design, improving production efficiency of gas transmission pipeline and ensuring pipeline safety. Taking the flow of hydrate particles in a Bending pipe as the object of study, the spiral flow attenuation and hydrate particle deposition under different bending pipe angles, different rate of bending pipe to diameter, different Reynolds number and different torsion were studied by numerical simulation method. The results show that the larger the swirl number, the higher the spiral flow intensity. When the fluid enters the bending pipe, the Angle of the bending pipe is larger, the torsional rate is smaller, and the Reynolds number is larger, the swirl number is larger, the intensity of the swirl flow is stronger, and the swirl number is larger at the same position. However, the larger the bending pipe to diameter ratio, the greater the change of the total swirl number and the weaker the strength at outflow, but the slower the change of swirl number, indicating that the spiral flow attenuation is slower. The larger the bending pipe Angle, the larger the bending pipe diameter rate, the smaller the torsion rate and the larger the Reynolds number, the smaller the deposition rate of the particles after flowing through the pipe. The results show that the spiral flow strength can be maintained in a proper way to reduce the deposition and ensure the safety of the conveying process.

In rice, symbiotic N fixation via nodule bacteroids does not take place naturally. Although N fixation by endophytic and associative diazotrophs has been reported in rice, main organs and seasonal regulation for the N fixation have not been elucidated. In this study, therefore, seasonal changes of nitrogenase (acetylene reduction) activity and carbohydrate contents in culm internode (IN), basal nodes (BN), and crown root (CR) were investigated in manure compost (MC)- and chemical fertilizer-applied rice. Nitrogenase activity increased after rooting, and reached the highest activity in BN of MC-applied rice at panicle initiation. In BN of MC-applied rice, the sucrose content was low whereas the higher glucose content was detected at panicle initiation. Although bacterial and diazotrophic bacterial populations were most abundant in CR, the nitrogenase activity seemed to be restricted by its trace sucrose and glucose contents. In addition, alpha-Proteobacteria and Clostridia phyla were abundant in BN-specific bacterial microbiota at panicle initiation. These results suggest that the increased N fixation in BN at panicle initiation might be sustained both by the non-structural carbohydrate supply from photosynthetic apparatus and BN-specific bacterial microbiota including diazotrophs.

In the paper, the author finds bounds of the sine and cosine along a circle on the complex plane in terms of two double inequalities for the norms of the sine and cosine along a circle on the complex plane.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

This article explores matter collineations (MCs) of static plane-symmetric spacetimes, considering the stress-energy tensor in its contravariant and mixed forms. We solve the MC equations in two cases: when the energy-momentum tensor is nondegenerate and degenerate. For the case of degenerate energy-momentum tensor, we employ a direct integration technique to solve the MC equations, which leads to an infinite-dimensional Lie algebra. On the other hand, when considering the nondegenerate energy-momentum tensor, the contravariant form results in a finite-dimensional Lie algebra with dimensions of either 4 or 10. However, in the case of the mixed form of the energy-momentum tensor, the dimension of the Lie algebra is infinite. Moreover, the obtained MCs are compared with those already found for covariant stress-energy.

In recent years, drones have been used in a wide range of fields such as agriculture, transportation of goods, and security. Drones equipped with communication facilities are expected to play an active role as base stations in areas where ground base stations are unavailable, such as disaster areas. In addition, asynchronous operation is being considered for local 5G in order to support all kinds of use cases. In asynchronous operation, cross-link interference between base stations is an issue. This paper attempts to reduce the interference caused by the drone network by introducing circularly polarized antennas. Numerical analyses are conducted to validate the effectiveness of the proposed system, where SIRs (Signal-to-Interference Ratio) are shown to be improved significantly as the numerical evaluation results.

Stress relaxation tests in cantilever bending were performed on the C7025 and C7035 alloys at 298K and 393K，respectively. The effect of stress-relief treatments on stress relaxation properties was investigated. The structural changes associated with the stress relaxation process were examined using transmission electron microscope. The stress relaxation curve fits well to empirical formula σ*=[Kˊln(t+α₀)+C]^-n for stress relaxation. The curves can be split into two stages. The stress relax quickly in the first stage, slows down in the second stage, and tends to be a certain limit value after a long time. The curve and microstructure reveals that the C7035 alloy has a lower rate of stress relaxation and a higher anti-stress relaxation capacity than the C7025. The first reason is that the movement of vacancies required by spinodal decomposition is inhibited, and the quantity of cobalt -containing vacancies decreases dramatically in the C7035 alloy. The other reason is that the precipitated phases became uniformly diffused in the C7035 alloy. The precipitate phase uniformly distributes in the grain boundaries and the matrix, during the relaxed condition, and thus the dislocations moving is blocked by the precipitates.

It is well known that X-ray crystallography is based on X-ray diffraction (XRD) by atoms and molecules. The diffraction pattern arises as a result of scattering of incident radiation, which makes it possible to determine the structure of the scattering substance. With the advent of ultrashort radiation sources, the theory and interpretation of X-ray diffraction analysis remained the same. This work shows that when an attosecond laser pulse is scattered on a DNA molecule, including during its nicking and bending, the pulse duration is an important characteristic of the scattering. In this case, the diffraction pattern changes significantly compared to the previously known scattering theory. The results obtained must be used in XRD theory to study DNA structures, their mutations and damage, since the previously known theory can produce large errors and, therefore, the DNA structure can be “deciphered” incorrectly.

Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a lot of structures in Europe and North America are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extent their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile reinforced mortar (CTRM) to bridge deck slabs and the webs of prestressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM-layer is a combination of a corrosion resistant carbon fibre reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

Rebar quantity estimation is pivotal for determining the cost of construction projects and essential for bidding purposes. A bar bending schedule plays a crucial role by providing rebar information and bending instructions, facilitating efficient procurement. Traditional methods of bar bending schedules, which involve manual extraction from 2D (two-dimensional) drawings, are error-prone and hinder construction productivity. This study proposes a Building Information Modeling (BIM)-based algorithm that automates the generation of a Bar Bending Schedule (BBS) directly from the 3D (three-dimensional) BIM models, ensuring accuracy and eliminating manual errors. The effectiveness of the algorithm was verified by comparing the rebar quantities generated by the model against those derived from optimization calculations. The results demonstrated a mean absolute error of 0.017 and a mean absolute percentage error of 1.13%, validating the algorithm’s precision. Additionally, it achieved a remarkable 33.33% reduction in the manpower required for preparing BBSs, highlighting its potential to revolutionize construction workflow efficiency and accuracy.

Many ethical issues arise when robots are introduced into elder-care settings. When ethically charged situations occur, robots ought to be able to handle them appropriately. Some experimental approaches use (top-down) moral generalist approaches, like Deontology and Utilitarianism, to implement ethical decision-making. Others have advocated the use of bottom-up approaches, such as learning algorithms, to learn ethical patterns from human behaviour. Both approaches have their shortcomings when it comes to real-world implementations. Human beings have been observed to use a hybrid form of ethical reasoning called Pro-Social Rule Bending, where top-down rules and constraints broadly apply, but in particular situations, certain rules are temporarily bent. This paper reports on implementing such a hybrid ethical reasoning approach in elder-care robots. We show through simulation studies that it leads to better upholding of human values such as autonomy, whilst not sacrificing beneficence.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

Efficient thermal management of modern electronics requires the use of thin films with highly anisotropic thermal conductivity. Such films enable the effective dissipation of excess heat along one direction while simultaneously providing thermal insulation along the perpendicular direction. In this study, we investigate the thermal conductivity of bilayer graphene (BLG) sheets using non-equilibrium molecular dynamics, examining both in-plane and cross-plane thermal conductivities. The in-plane thermal conductivity of 10 nm × 10 nm BLG with zigzag and armchair edges at room temperature is found to be around 204 W/m.K and 124 W/m.K, respectively. The in-plane thermal conductivity of BLG increases with sheet length. For all sizes, BLG with a zigzag edge exhibits higher thermal conductivity than that of the armchair edge, with this difference becoming more pronounced as the lengths of the sheets increase. In addition, increasing temperature from 300 K to 600 K decreases the in-plane thermal conductivity of a 10 nm× 10 nm zigzag BLG by about 34%. Similarly, the application of a 12.5% tensile strain induces a 51% reduction in its thermal conductivity compared to the strain-free values. Armchair configurations exhibit similar responses to variations in temperature and strain, but with less sensitivity. Furthermore, the cross-plane thermal conductivity of BLG at 300 K is estimated to be 0.05 W/m·K, significantly lower than the in-plane results by approximately four orders of magnitude. The cross-plane thermal conductance of BLG decreases with increasing temperatures, specifically, at 600 K, its value is almost 16% of that observed at 300 K.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

Primocane-fruiting (PF) blackberries are adaptable to different production systems. To increase yields in PF blackberries, their primocanes are typically tipped or topped in summer to encourage branch formation from axillary buds below the cut. In this study, we determined in PF ‘Prime-Ark Traveler’ whether early emerging primocanes were more productive than those that emerged later in the season and the effect of primocane bending and defoliation on flowering. The primocanes that emerged in April produced 64% more flower shoots than those that emerged after May. Also, these findings indicate the alternative primocane management practices of selecting the early emerging primocanes and bending to orient primocanes horizontally and leaf removal increase budbreak and flower shoot emergence. The present work contributes toward a better understanding of primocane emergence time and orientation-flowering relations and how they mediate crop performance in PF blackberry.

Victor Vasarely’s (1906-1997) important legacy to the study of human perception is brought to the forefront and discussed. A large part of his impressive work conveys the appearance of striking three-dimensional shapes and structures in a large-scale pictorial plane. Current perception science explains such effects by invoking brain mechanisms for the processing of monocular (2D) depth cues. Here in this study, we illustrate and explain the local effects of 2D color and contrast cues on the perceptual organization in terms of figure-ground assignments, i.e. which local surfaces are likely to be seen as “nearer” or “bigger” in the image plane. Paired configurations are embedded in a larger, structurally ambivalent pictorial context inspired by some of Vasarely’s creations. The figure-ground effects these configurations produce reveal a significant correlation between perceptual solutions for “nearer” and “bigger” when no other monocular depth cues are given in the image. In consistency with previous findings on similar, albeit simpler visual displays, a specific color may compete with luminance contrast in resolving the planar ambiguity of a complex pattern context. Vasarely intuitively understood, and successfully exploited, this kind of subtle context effect in his art, well before empirical investigations had set out to study and explain their genesis in terms of information processing by the visual brain.

Hypotrochoidal profile contours have been produced in industrial applications in recent years using twin-spindle processes, and they are considered effective high-quality solutions for positive shaft–hub connections. This study mainly concerns analytical approaches to determine the bending stresses in hypotrochoidal profile shafts. The formulation was developed according to bending principles using the mathematical theory of elasticity and conformal mappings. The loading was further used to investigate the rotating bending behaviour. The stress factors for the classical calculation of maximum bending stresses were also determined for all those profiles presented and compiled in the German standard DIN3689-1 for practical applications. The results were also compared with the corresponding numerical and experimental results, and very good agreement was observed. Additionally, based on previous work, the stress factor was determined for the case of torsional loading to calculate the maximum torsional stresses in the standardised profiles, and the results are listed in a table. This study contributes to the further refinement of the current DIN3689 standard.

This research aims to investigate the carbon fiber reinforced polymer (CFRP) when subjected to tensile, bending, and compression. Half of the specimens are also subjected to water to find out how water influences. The CFRP is created using a combination of carbon fiber layers and epoxy resin Bisphenol A Epichlorohydrin with hardener and is formed using the vacuum infusion method. From the water absorption test, it was found that the average weight gain of the specimens was 2.9% and the lowest value was at 0.6%, it was concluded that the increase in wet specimen weight was not too significant and water absorption tended to be slow. Mechanical testing ob-tained the highest average tensile stress, bending stress, compressive stress, and modulus of elasticity of 195 MPa, 295 MPa, 96 MPa, and 8914 MPa were from dry specimens while the lowest average values were 146 MPa, 286 MPa, 81 MPa, and 6160 MPa from wet specimens. The results of micro-photo observations on the tensile test fracture show that the specimen has a XGM fracture character with delamination and splitting fractures happening in multiple areas. In the bending test, the specimens experienced buckling fracture due to the fiber breaking and the inability of the matrix to withstand the additional stress. Shear fracture happened during the compressive test. In conclusion, water absorption has a bad impact towards the composite strength.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries have been tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance have been determined. Results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with previous studies results, to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

Carbon fiber reinforced polymers (CFRP) are extensively employed in the aerospace industry due to their excellent properties. Delamination damage occurring at critical locations in CFRP can seriously reduce the safety of in-service components. The detection and localization of delamination damage using Lamb waves hold significant potential for widespread application in non-destructive testing. However, the choice of damage localization algorithm may produce different delamination damage localization results. This research presented an IRAPID (improved reconstruction algorithm for probabilistic inspection of defects) method derived from the ORAPID (original reconstruction algorithm for probabilistic inspection of defects) method, aiming to improve the accuracy and reliability of delamination damage localization. Three CFRP bending plates, including a healthy bending plate and two bending plates with delamination damage sizes of Φ20 mm and Φ40 mm, were prepared in the experiment, respectively. The detection experiment of the CFRP bending plate using lead zirconate titanate (PZT) as a transducer to excite and receive Lamb waves was conducted, and the influence of excitation signal frequency on the performance of the proposed method was discussed. Under the condition of excitation signal frequency of 220 ~ 320 kHz and step size of 10 kHz, the accuracy of the delamination damage localization method proposed in this paper was compared with that of the existing methods. The experimental results indicate that the IRAPID algorithm exhibits good stability in the localization of delamination damage across the frequency variations range considered. The localization error of the IRAPID algorithm for delamination damage is significantly lower than that of the DaS (delay-and-sum) algorithm and the ORAPID algorithm. As the size of the delamination damage increases, so does the localization error. The accuracy of delamination damage localization is lower in the X-axis direction than in the Y-axis direction. By averaging the localization results across various frequencies, we can mitigate the potential localization errors associated with single-frequency detection to a certain extent. For the localization of delamination damage, Lamb waves at multiple frequencies can be employed for detection, and the detection results at each frequency are averaged to enhance the reliability of localization.

In this paper, thin plate theory and moderately thick plate theory are proposed for analyzing the bending problem of rectangular plates with stepped thickness resting on elastic half-space foundation. The ground reaction is considered as an unknown coefficient and the hypothesis of Winkler foundation model and two-parameter ground model is eliminated in this method, so as to obtain the law of internal force distribution of the plate and the distribution law of contact reaction force between the stepped rectangular plate and foundation. The stepped rectangular plate is divided into upper and lower plates, and thin plate theory and moderately thick plate theory are used to obtain the analytical solution. The obtained analytical solutions in this paper are compared with results reported in other publications to verify the accuracy of this method. The effects of the elastic modulus and dimensions of the plate, and theory of plate are also considered. The analytical solutions show that it is feasible to decompose the stepped rectangular plate into two plates for analyzing the bending properties of stepped rectangular plate, and this method provide a reference for the study of multilayer stepped rectangular plates.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

Single-layer core corrugated sandwich panels generally consist of a corrugated core and two layers of panels, while multi-layer core corrugated sandwich panels are formed by stacking multiple layers of panels with multiple layers of core layers. In this study, integrated multilayer core corrugated sandwich panels with different shapes of corrugated cores (triangular, trapezoidal, and rectangular) and the different number of core layers were fabricated using 3D printing technology, and the mechanical behavior of such multilayer core corrugated sandwich panels under quasi-static three-point bending was investigated using experiments and numerical simulations. The effects of core shape and number of core layers on the bending deformation process, damage mode, load carrying capacity, and bending energy dissipation capacity of multilayer core sandwich panels are discussed. Parametric design of multilayer triangular core corrugated sandwich panels was also carried out by finite element software ABAQUS. It was found that a new multilayer corrugated sandwich panel with a multi-layer core is better than the single core shape multilayer corrugated sandwich panel in terms of bending load capacity, energy dissipation capacity and deformation capacity can be obtained through the combination design of different core shapes.

Despite their limited spatial extent, freshwater ecosystems host remarkable biodiversity, including one third of all vertebrate species. This biodiversity is declining dramatically: globally, wetlands are vanishing three times faster than forests and freshwater vertebrate populations have fallen more than twice as steeply as terrestrial or marine populations. Threats to freshwater biodiversity are well- documented but co-ordinated action to reverse this decline is lacking. We present an Emergency Recovery Plan to “bend the curve” of freshwater biodiversity loss. Priorities for action include: 1) accelerating implementation of environmental flows, 2) improving water quality, 3) protecting and restoring critical habitats, 4) managing exploitation of freshwater species and riverine aggregates, 5) preventing and controlling non-native species invasions, and 6) safeguarding and restoring river connectivity. We recommend revised targets and indicators for the Convention on Biological Diversity and the Sustainable Development Goals, and investment in enabling conditions at national, river basin and local scales.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

This paper presents an analytical method for determining the bending stresses and deformations in prismatic noncircular profile shafts with trochoidal cross sections. The so-called higher trochoids can be used as form-fit shaft–hub connections. Hybrid (mixed) higher trochoids (M-profiles) were proposed in [1] and adapted to a practical industrial application in [2]. M-profiles combine the advantages of standardised polygon (DIN 32711 [3]) and spline (DIN 5486 [4]) contours used as shaft–hub connections for the transmission of torsional loads. In this study, the geometric and mechanical properties of the higher hybrid trochoids were investigated using complex functions to simplify the calculations. The pure bending stress and shaft deflection were determined for M-profiles using the bending theory formulated by Muskhelishvili [5]. The loading cases consisted of static and rotating bends. Analytical, numerical, and experimental results agreed well.

Partially stabilized zirconia (PSZ) is a promising material with superior combination properties in a wide range of industries. In this study, the effect of grain size on the mechanical properties such as hardness, bending strength and fracture toughness (named as ‘indentation toughness’ in this study) was investigated. The multi-doped zirconia ceramics were prepared by powder processing and pressure-less sintered following four sintering schedules. The measured mechanical properties results show that the polymorph structure sintered at a higher temperature has a lower bending strength and hardness. But 300% more indentation toughness (30.54 Kg/mm) of samples sintered at 1600 °C +1150 °C relative to others was estimated due to the grain size effect by our suggested equation. By contrast, the fracture toughness was calculated with an existing method. The results showed that similar trends were obtained. It appeared to be a novel method for evaluating the toughness of partially stabilized zirconia ceramics with micron grains based on the size effect.

Hybrid fiber reinforced composites can be controlled by price, weight and various mechanical properties depending on fiber ratio and lamination method. Despite these excellent hybrid properties, there is a disadvantage that inter-laminar fracture due to external impact, which is the biggest weakness of fiber reinforced composite materials, is weak. The test specimens were prepared by using a vacuum bag method, which is manufactured by using an autoclave device. The pre-preg is manufactured in the form of a B-stage. In the process of fabricating the nanoparticle pre-preg, the homogeneizer using an ultrasonic wave was used to disperse the epoxy subject without the curing agent into nanoparticles. The dispersion of the nanoparticles was dispersed by the weight of the epoxy resin. This is to take into account the cohesion of HNT and to understand the range of cohesion of HNT in a matrix with viscosity and its phenomenon. According to the Comparison of the interlayer interfacial properties and mechanical properties of Aramid / Basalt fiber hybrid composites by HNT addition, the fracture toughness, ILSS and bending strength of specimens with HNT content of more than a certain level were decreased because of the aggregation of HNT.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

Background: We previously found that QNBC tumors are more frequent in African Americans compared to TNBC tumors. To characterize this subtype further, we sought to determine the miRNA-mRNA profile in QNBC patients based on race. Methods: Both miRNA and mRNA expression data were analyzed from TCGA and validated using datasets from the METABRIC, TCGA proteomic, and survival analysis by KMPLOT. Results: miRNA-mRNAs which include FOXA1 and MYC (mir-17/20a targets); GATA3 and CCNG2 (mir-135b targets); CDKN2A, CDK6, and B7-H3 (mir-29c targets); and RUNX3, KLF5, IL1-β, and CTNNB1 (mir-375 targets) were correlated with basal-like and immune subtypes in QNBC patients and associated with a worse survival. Conclusion: Thus, QNBC tumors have an altered gene signature implicated in racial disparity and poor survival.

The Hertzian contact theory, as well as most of the other classical theories of normal and tangential contact, provides displacements and the distribution of normal and tangential stress components directly in the contact surface. However, other components of the full stress tensor in the material may essentially influence the material behaviour in contact. Of particular interest are principal stresses and the equivalent von Mises stress, as well as the gradient of the hydrostatic pressure. For many engineering and biomechanical problems, it would be important to find these stress characteristics at least in the contact plane. In the present paper, we show that the complete stress state in the contact plane can be easily found for axially symmetric contacts under very general assumptions. We provide simple explicit equations for all stress components and the normal component of the gradient of hydrostatic pressure in the form of one-dimensional integrals.

Introduction Cone Beam Computed Tomography (CBCT) scans should be digitally oriented using a reference plane before being evaluated for patient growth and treatment outcome. Current orientation planes are usually dependent on the Porion points. Using more reliable landmarks than the Porion, we introduce the Acta plane and investigate its reliability as an alternative reference plane for cases in which the Porion point is inaccessible. Methods To test its reliability, a dental student and an orthodontist located sixteen skeletal and dental landmarks in sixteen CBCT scans, before and after reorientation. Also, four measurements were calculated based on these landmarks’ coordinates. The reorientation of these CBCT scans with the Acta plane was done by another dental student. Intraclass Correlation Coefficient (ICC) was calculated before and after orientation, intra- and inter-examiner. The data were tested for significance through the Shapiro Wilk test with a threshold set at 0.05. Through the ICC variation of the points’ coordinates, this article also evaluated the reliability of this plane with the t-paired and exact-sign tests. Results: The identification of landmarks was more reliable in the reoriented CBCT images than in the original images, with a significant increase of 0.012 in the median of the ICC. Linear and angular measures showed no significant differences between groups. Conclusion This plane is a reliable alternative for the orientation of CBCT images. The design of the Acta plane might allow the use of a smaller field of view and, consequently, a reduction in the radiation dose.

The present studies were undertaken to address the role of fetuin-A in the growth and invasion potential in a triple negative breast cancer (TNBC) cell line, MDA-MB-468. Basal like TNBC that express high levels of ectopic fetuin-A have poorer prognosis for the patients compared to those that express low levels of the protein. We overexpressed fetuin-A in MDA-MB-468 and then determined the invasive potential of fetuin-A overexpressing cells vs controls transfected with empty vector. We also determined the adhesion and growth potential of the cells in the presence of only fetuin-A in serum free medium and also in complete medium. Our data suggest that fetuin-A overexpression significantly enhances the invasive potential of the cells and also the expression of Toll like receptor 4 (TLR4) on these cells. More importantly, the cells rely on fetuin-A-TLR4 signaling network for growth and invasion because the specific TLR4 inhibitor CLI-095 (resatorvid) abrogates fetuin-A mediated growth and invasion. Taken together, the data suggest that fetuin-A-TLR4 signaling network plays a significant role in the growth and invasion potential of TNBC.

The three-point bending behavior of a single Au nanowire deformed with an atomic force microscope was monitored by coherent X-ray diffraction using a sub-micrometer sized hard X-ray beam. While three-dimensional reciprocal-space maps were recorded before and after deformation by standard rocking curves, they were measured by scanning the energy of the incident X-ray beam during deformation at different loading stages. The mechanical behavior of the nanowire is visualized in reciprocal space and a complex deformation mechanism is described. In addition to the expected bending of the nanowire, torsion is detected. Bending and torsion angles are quantified from the high resolution diffraction data.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

Cellular locomotion is required for survival, fertility, proper embryonic development, regeneration, and wound healing. Cell migration is a major component of metastasis, which accounts for two-thirds of all solid tumor deaths. While many studies have demonstrated increased energy requirements, metabolic rates, and migration of cancer cells compared to normal cells, few have systematically compared normal and cancer cell migration as well as energy requirements side by side. Thus, we investigated how non-malignant and malignant cells migrate utilizing several cell lines from the breast and lung. Initial screening was done in an unbiased high-throughput manner for the ability to migrate/invade on collagen and/or Matrigel. We unexpectedly observed that all the non-malignant lung cells moved significantly faster than cells derived from lung tumors regardless of growth media used. Given the paradigm-shifting nature of our discovery, we pursued possible mechanisms responsible. Neither mass, cell doubling, nor volume, accounted for the individual speed and track length of the normal cells. Non-malignant cells had higher levels of ATP at premigratory-wound induction stages. Meanwhile, cancer cells also increased ATP at premigratory-wound induction – but not to the levels of the normal cells, indicating the possibility for further therapeutic investigation.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

Thin-wall heat pipe is an efficient heat transfer component, which has been widely used in the field of heat dissipation of high-power electronic equipment in recent years. In this study, the orange peel morphology defect of thin-wall heat pipes after bending deformation was analyzed both for the macro 3D profile and for the micro-formation mechanism. The results show that after high temperature sintering treatment, the matrix grains of heat pipe are coarsened seriously and formed a strong Goss texture, while a certain annealing twins with the unique Copper orientation are retained. The distribution of Schmid factor value subjected to the uniaxial stress indicate the inhomogeneity of intergranular deformation exist among the annealing twins and matrix grains. The annealing twin exhibit a “hard-oriented” component during the deformation; thus, it plays a role as barrier and hinder the slipping of dislocation. As the strain accumulates, part of the annealing twins may protrude from the surface of heat pipe, forming a large-scale fluctuation of the surface as the so called the “orange peel” morphology. The 3D profile shows the bulged twins mostly perpendicular to the drawing direction, with about 200-300μm in width and 10-20μm in height.

This paper investigates the classical but yet intriguing question of modeling orthotropic RC floor systems endowed with lightening elements, by means of a uniform orthotropic slab, in order to describe accurately the building response under seismic loads. The simplified method, commonly adopted by engineers, based on the equivalence between the transverse stiffness of the RC elements of the real floor and those of the orthotropic slab is presented. A case study in which this simplified method is used is also provided. Then, an advanced finite elements (FE) based method to determine the elastic properties of the equivalent homogenized orthotropic slab is proposed. Based on the results obtained from the application of this method to a case study, a discussion on the adequacy of the simplified method is also provided.

To further understand the role of phosphorylation in ISGF3- and STAT2/IRF9-mediated constitutive and long-term IFN-I-stimulated transcriptional responses, we performed RNA-Seq and ChIP-Seq, in combination with phosphorylation inhibition and anti-viral experiments. First, we identified a group of ISRE-containing ISGs that were commonly regulated in IFNα treated WT and STAT1-KO cells. Thus, in 2fTGH and Huh7.5 WT cells IFNα-inducible transcription and anti-viral activity relied on the recruitment of the ISGF3 components STAT1, STAT2 and IRF9 in a phosphorylation- and time-dependent manner. Likewise, in ST2-U3C and Huh-STAT1KO cells lacking STAT1, ISG expression correlated with DNA-binding of phosphorylated STAT2/IRF9. This pointed to a dominant role of classical ISGF3 and STAT2/IRF9, and not U-ISGF3 or U-STAT2/IRF9, in the regulation of early and prolonged ISG expression and viral protection, in WT and STAT1-KO cells. In addition, comparative experiments in U3C (STAT1-KO) cells overexpressing all ISGF3 components (ST1-ST2-IRF9-U3C), revealed a threshold-dependent role of U-ISFG3, and potentially U-STAT2/IRF9, in the regulation of constitutive and possibly long-term IFNα-treated ISG expression and anti-viral activity.

Additive manufacturing (AM) are used in several industries such as automotive, aerospace, and medical sciences. One of the most common devices used in additive manufacturing is fused deposition modeling (FDM) 3D printers. This fabrication method has different inputs that affect the quality of the parts. In this research, the bending fatigue properties of polylactic acid (PLA) biomaterial made with a 3D printer are investigated. To demonstrate the influence of printing parameters on fatigue lifetime, standard specimens with nozzle diameters of 0.2-0.6 mm, extruder temperature of 180-240°C, and print speed of 5-15 mm/s were printed. After performing fully-reversed bending fatigue tests, it was found that printed specimens at 180°C have the best fatigue lifetime in most cases. Accordingly, fatigue behavior improved by reducing the nozzle diameter. Printing at lower temperatures also improved fatigue lifetime. The printing speed affected the slope of the S-N diagram, known as the fatigue strength exponent.

Agroforestry systems with multipurpose tree species, for the double production of timber and fruit, along with the intercropping with herbaceous crops, can be fundamental land use systems for multiple ecosystems services. Research was conducted in Italy, for one growing season, in 18 years old agroforestry experimental plots with common walnut (Juglans regia L.) trees, according to the previous agroforestry management (AFM) since tree planting. The aim is i) estimating trees growth and herbaceous yield in relation to increasing tree size, especially referring to the trees basal area (G); ii) evaluating the role of nut production as additional product to timber and food crops. Observations were run on tree growth and leaf phenology, total light transmittance (TTL) below tree canopy and hay yield with and without walnut intercropping. Nut yield was estimated from available literature and associated to G. At the end of the study year, representing two third of trees rotation, their height varied between 10 and 11 m, with much larger variation for tree diameter between 17 and 22 cm, according to the previous AFM, including tree mulching with plastic film. Hay yield varied between 4.5 and 3 Mg ha year-1 outside and under tree canopy, respectively. Negative regression were determined for G and TTL, and G and hay yield, with an annual reduction of 5% per G unit. Simulations were run on hay and nut yield, using G as main input parameter. The work points out the following key findings: i) the usefulness of plastic mulching, at tree planting, to increase the long-term timber productivity of the trees intercropped with herbaceous crops; ii) the negative linear relationship between hay productivity and walnut trees G; iii) G influences, in positive way, more markedly nut than hay yield. Suggestions are given on the optimum tree planting spacing and AFM for balancing timber, nut and hay yields.

Pancreatic ductal adenocarcinoma (PDAC) is a fatal disease due to early metastatic spread, late diagnosis and the lack of efficient therapies. A major driver of cancer progression and hurdle to successful treatment is the desmoplastic reaction of the tumor stroma, the formation of which is orchestrated by transforming growth factor (TGF)-β. Recent data from pancreatic cancer mouse models have shown that the TGF-β pathway is controlled by transcriptionally active p73 (TAp73) through secretion of biglycan (Bgn) via intermittent expression of the TGF-β signaling intermediates, Smad3 and Smad4. Genetic knockout of TP73, and, as a consequence, deficient induction of Smad3/Dpc4 and secretion of Bgn led to activation of TGF-β signaling through a (Smad-independent) ERK pathway, favoring epithelial-mesenchymal transition (EMT) and cell motility. Except for BGN, these functions of TAp73 have recently been shown to also operate in human PDAC cells and are reminiscent of what we previously observed for the small GTPase, RAC1b. This prompted us to hypothesize that TAp73 and RAC1b are part of the same tumor-suppressive pathway in human PDAC cells. The two objectives of this study, therefore, were to reveal i) if the regulatory interactions between TAp73 and Bgn previously discovered in murine PDAC-derived cells also operate in their human counterparts, and ii) if RAC1b collaborates with TAp73 in these tumor-suppressive activities in human PDAC cells. Using a variety of experimental approaches, including mutual rescue experiments, we were able to show that the previously proposed tumor-suppressive TAp73-Smad4-Bgn signaling also operates in human cells and that RAC1b is as an upstream activator of this pathway. Our findings highlight the complex role of TGF-β in pancreatic tumorigenesis and might have implications for therapeutic approaches targeting this growth factor for inhibition.

Mapping building roof plane structures is an active research direction in urban-related studies, as understanding roof structure provides essential information for generating highly detailed 3D building models. Traditional deep learning models have been the main focus of most recent research endeavours aiming to extract pixel-based building roof plane areas from remote sensing imagery. However, significant challenges arise, such as delineating complex roof boundaries and invisible boundaries. Additionally, challenges during the post-processing phase, where pix-el-based building roof plane maps are vectorized, often result in polygons with irregular shapes. In order to address this issue, this study explores a state-of-the-art method for planar graph reconstruction applied to building roof plane extraction. We propose a framework for reconstructing regularized building roof plane structures using aerial imagery and cadastral information. Our framework employs a holistic edge classification architecture based on an attention-based neural network to detect corners and edges between them from aerial imagery. Our experiments focused on three distinct study areas characterized by different roof structure topologies: Stadsveld – 't Zwering neighbourhood and Oude Markt area, located in Enschede, The Netherlands, and the Lozenets district in Sofia, Bulgaria. The outcomes of our experiments revealed that a model trained with a combined dataset of two different study areas demonstrated superior performance, capable of delineating edges obscured by shadows or canopy. Our experiment in the Oude Markt area resulted in building roof plane delineation with an F-score value of 0.43 when the model trained on the combined dataset was used. In comparison, the model trained only on the Stadsveld – 't Zwering dataset achieved an F-score value of 0.37, and the model trained only on the Lozenets dataset achieved an F-score value of 0.32. The results from the developed approach are promising and can be used for 3D city modelling in different urban settings.

With the increased use of simulation based training using animal models for the education of surgical and anaesthetic techniques, an increased understanding of the anatomy of such models and how they compare to humans is required. The transversus abdominis plane block is a regional anaesthetic technique that requires an understanding of the abdominal wall anatomy along with proficient ultrasound use. The current review aims to compare the anatomy of the abdominal wall across species, particularly focussing on the pertinent differences within the class of mammals, and secondarily, it aims to address the implications of these differences for simulation based training of the transversus abdominis plane block. To achieve this, the PubMed, Web of Science and Google Scholar databases were searched for relevant literature. The mammalian abdominal wall differs in its musculature, vasculature or innervation from that of amphibians, birds or reptiles, however, among species of mammals, the structure of the abdominal wall follows a similar framework. Particular differences among mammals include the additional muscular layer of the panniculus carnosus found in most mammals other than humans, the variable arterial origins and dominant vascular supply of the abdominal wall and the number of thoracolumbar nerves innervating the abdominal wall. When using animal models for simulation based training, the pig is recommended for the transversus abdominis plane block given its closely homologous abdominal wall structure, availability and larger comparative size.

In the study of materials and macromolecules by first-principle methods, the bond order is a useful tool to represent molecules, bulk materials and interfaces in terms of simple chemical concepts. Despite the availability of several methods to compute the bond order, most applications have been limited to small systems because a high spatial resolution of the wave function and an all-electron representation of the electron density are typically required. Both limitations are critical for large-scale atomistic calculations, even within approximate density-functional theory (DFT) approaches. In this work we describe our methodology to quickly compute delocalization indices for all atomic pairs, while keeping the same representation of the wave function used in most compute-intensive DFT calculations on high-performance computing equipments. We describe our implementation into a post-processing tool, designed to work with Quantum ESPRESSO, a popular open-source DFT package. In this way we recover a description in terms of covalent bonds from a representation of wave function containing no explicit information about atomic types and positions.

We study the resonant dipole-dipole interaction energy between two uniformly accelerated identical atoms, one excited and the other in the ground state, prepared in a correlated Bell-type state, and interacting with the scalar field or the electromagnetic field nearby a perfectly reflecting plate. We suppose the two atoms moving with the same uniform acceleration, parallel to the plane boundary, and that their separation is constant during the motion. We separate the contributions of vacuum fluctuations and radiation reaction field to the resonance energy shift of the two-atom system, and show that Unruh thermal fluctuations do not affect the resonance interaction, which is exclusively related to the radiation reaction field. However, nonthermal effects of acceleration in the radiation-reaction contribution, beyond the Unruh acceleration-temperature equivalence, affect the resonance interaction energy. By considering specific geometric configurations of the two-atom system relative to the plate, we show that the presence of the mirror significantly modifies the resonance interaction energy between the two accelerated atoms. In particular, we find that new and different features appear with respect to the case of atoms in the free space, related to the presence of the boundary and to the peculiar structure of the quantum electromagnetic field vacuum in the locally inertial frame. Our results suggest the possibility to exploit the resonance interaction between accelerated atoms, as a probe for detecting the elusive effects of atomic acceleration on radiative processes.

Monocarboxylate transporter 8 (MCT8) and organic anion-transporting polypeptide 1C1 (OATP1C1) are thyroid hormones (TH) transmembrane transporters relevant for the availability of TH in neural cells, crucial for their proper development and function. Mutations in MCT8 or OATP1C1 result in severe disorders with dramatic movement disability related to alterations in basal ganglia motor circuits. Mapping the expression of MCT8/OATP1C1 in those circuits is necessary to explain their involvement in motor control. We studied the distribution of both transporters in the neuronal subpopulations that configure the direct and indirect basal ganglia motor circuits using immunohistochemistry and double/multiple labeling immunofluorescence for TH transporters and neuronal biomarkers. We found their expression in the medium-sized spiny neurons of the striatum (the receptor neurons of the corticostriatal pathway), and in various types of its local microcircuitry interneurons, including the cholinergic. We also demonstrate the presence of both transporters in projection neurons of intrinsic and output nuclei of the basal ganglia, motor thalamus and nucleus basalis of Meynert, suggesting an important role of MCT8/OATP1C1 for modulating the motor system. Our findings suggest that a lack of function of these transporters in the basal ganglia circuits would significantly impact motor system modulation, leading to clinically severe movement impairment.

Carbon fiber reinforced polymer (CFRP) bending structure is widely used in the aviation field. The occurrence and propagation of delamination damage will reduce the safety of in-service bending structures. As a detection tool with high damage sensitivity, Lamb wave can effectively identify delamination damage. In this study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0 and S0 mode lamb waves to delamination damage. The simulation results show that compared with the S0 mode Lamb wave, the A0 mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0 mode and S0 mode Lamb wave to identify delamination damage of different sizes. The A0 mode Lamb wave was excited by the developed one-dimensional linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with fitting expression is not larger than 0.8 mm, and the percentage error is not more than 8%.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyzer. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/μϵ (1 μϵ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 μN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

The paper presents section models for analysis of the resistance of RC members subjected to bending moment with or without axial force. To determine the section resistance the nonlinear stress-strain relationship for concrete in compression is assumed, taking into account the concrete softening. It adequately describes the behavior of RC members up to failure. For the reinforcing steel linear elastic-ideal plastic model is applied. For the ring cross-section subjected to bending with axial force the normalized resistances are derived in the analytical form by integrating the cross-sectional equilibrium equations. They are presented in the form of interaction diagrams and compared with the results obtained by testing conducted on RC columns under eccentric compression. Furthermore, the ultimate normalized bending moment has been derived for the rectangular cross-section subjected to bending without axial force. It was applied in the cross-sectional analysis of steel and concrete composite beams, named BH beams, consisting of the RC rectangular core placed inside a reversed TT welded profile. The comparisons made indicated good agreements between the proposed section models and experimental results.

As is well known, the main contribution of the FRP strips to the strength of load-bearing walls is an improvement in the in-plane strength. This paper deals with the possibility of applying the FRP strips in way to modify the strengthening mechanism of the FRP reinforcing system, from an in-plane to an out-of-plane strengthening mechanism. In order to achieve this goal, a second reinforcement system – derived from the CAM system (Active Confinement of Masonry) – provides connections between the FRP strips placed on the opposite sides of the wall. This new strengthening technique – called the straps/strips technique – establishes a stiffness constraint that forces the opposing FRP strips to behave like two flanges of an FRP I-beam embedded in the wall. Consequently, the use of FRP strips also improves the flexural strength of the wall. The present paper briefly summarizes the results obtained in previous works with the straps/strips technique and proposes an improvement of this strengthening technique, based on some weak-points emerged in the early experimentations. The paper also shows the results of a further experimental test, performed with the improved straps/strips technique. Finally, the similarity between FRP strips with transversal connection and concrete wythes of a sandwich panel with flexible connectors leads to interpret the behavior of the ideal I-beam in terms of composite action established between the FRP strips. This paves the way for analytical modeling of the straps/strips technique.

The study of neurodegenerative diseases using pluripotent stem cells requires new methods to assess neurodevelopment and neurodegeneration of specific neuronal subtypes. The cholinergic system, characterized by its use of the neurotransmitter acetylcholine, is one of the first to degenerate in Alzheimer’s disease and is also affected in frontotemporal dementia. We developed a differentiation protocol to generate basal forebrain cholinergic neurons (BFCNs) from induced pluripotent stem cells (iPSCs) aided by the use of small molecule inhibitors and growth factors. Ten iPSC lines were successfully differentiated into BFCNs using this protocol. The neuronal cultures were characterised through RNA and protein expression, and functional analysis of neurons was confirmed by whole-cell patch clamp. We have developed a reliable protocol using only small molecule inhibitors and growth factors, while avoiding transfection or cell sorting methods, to achieve a BFCN culture that expresses the characteristic markers of cholinergic neurons.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

The object of this paper is the bending analysis of isotropic rectangular Kirchhoff plates subjected to non-uniform heating (NUH) using the Fourier transform method. The bottom and top surfaces of the plate are assumed to have different changes in temperature, whereas the change in temperature of the mid-surface is zero. According to classical plate theory, the governing equation of the plate contains second derivatives of the NUH; these derivatives are zero by constant value of the NUH, which leads to its absence in the governing equation. This paper presented an approach by which Fourier sine transform was utilized to describe the NUH, while the double trigonometric series of Navier and the simple trigonometric series of Lévy were utilized to describe the deflection curve. Thus, the NUH appeared in the governing equation, which simplified the analysis. Rectangular plates simply supported along all edges were analyzed, bending moments, twisting moments, and deflections being determined. In addition, rectangular plates simply supported along two opposite edges were analyzed; the other edges having various support conditions (free, simply supported, and fixed).

Thermal stresses belong to the leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature properties of asphalt mixtures, three point bending and uniaxial tensile creep tests were applied and the master curves of stiffness modulus were analyzed. On the basis of creep test results, rheological parameters describing elastic and viscous properties of the asphalt mixtures were determined. Thermal stresses were calculated and compared to tensile strength of the material to obtain the failure temperature of the analyzed asphalt mixtures. It was noted that lower strain values of creep curves were obtained for the Tensile Creep Test (TCT) than for the Bending Beam Creep Test (BBCT), especially at lower temperatures. Results of thermal stress calculations indicated that higher reliability was obtained for the viscoelastic Monismith method based on the TCT results than for the simple quasi-elastic solution of Hills and Brien. The highest agreement with the TSRST results was also obtained for the Monismith method based on the TCT results. No clear relationships were noted between the predicted failure temperature and different methods of thermal stress calculations.

The diamagnetic levitation technique can be applied to non-destructive testing for identifying cracks and defects in magnetic materials. Pyrolytic graphite is a material that can be leveraged in micromachines due to its no-power diamagnetic levitation on a permanent magnet (PM) array. However, the damping force applied to pyrolytic graphite prevents it from maintaining con-tinuous motion along the PM array. This paper investigates the in-plane motion and damping characteristics of pyrolytic graphite sheets on the PM array. The centroid of pyrolytic graphite will maintain a stable levitation when positioned on the intersecting point of the PM array. Fur-thermore, the in-plane motion of two different pyrolytic graphite sizes - PG10 (10×10×0.5mm3) and PG20 (20×20×0.5mm3) - has revealed that the in-plane forces applied to them are approximately 61.4μN and 28.2μN, respectively. The smaller sheet has a shorter oscillation time while oscillating before it stabilizes. The damping ratio of the oscillation was between 0.1-0.2. The in-plane force and the stable time of pyrolytic graphite are related to its size ratio in comparison with the PM. This relationship is believed to promote stability, as the force acting on the graphite sheet will be distributed over a larger area when the sheet size increases. During the fixed-axis rotation process, the study found that the friction coefficient and friction force decreased as the rotational speed decreased. The diamagnetic levitation of pyrolytic diamagnetic levitation is also unable to maintain long-term axial rotation. Finally, friction force was tested using PG10 during fixed-axis rotation above a circular PM array. The results showed that the order of the friction coefficient is 10-3, and the friction force is about 0.8μN, decreasing with graphite rotation speed. We hope this technique will be used in crack detection, magnetic detection and other micromachine.

This study discusses the experimental assessment of the in-plane mechanical behavior of a multi-leaf stone masonry wall built from cut stone and reinforced with metal connectors (cramps and dowels). The wall, inspired by conventional multi-leaf stone walls, is meant for use in modern stone masonry buildings. The wall is constructed from two parallel load-bearing walls with a cavity between them, which aims to conceal the installation and insulation needed in modern buildings. The load-bearing walls are connected with cramps and dowels at certain intervals so that the wall works as a single section against horizontal and vertical loads. To characterize the in-plane behavior of the proposed wall, compressive, triplet, and diagonal compression tests were conducted to investigate the compressive strength, shear strength, modulus of elasticity, stiffness, ductility, and energy absorption of the wall. Compared with dry and mortar joint walls, the use of dowels increased the initial shear capacity of the wall by 11 and 19 times, respectively. The application of cramps without curving channels inside the individual stone elements decreased the compressive strength by 18%. The energy absorption of the designed walls with metal connectors was substantially increased to that of the specimens representing conventional stone walls. The results obtained show the applicability of the wall due to its higher shear strength and minimal drop in compressive strength, which is within acceptable limits.