To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

In this paper, we dive into the exciting world of wireless communication, focusing on how millimeter-wave technology and Multiple-Input Multiple-Output phased array antennas are shaping the future of 5G and the upcoming 6G technologies. We cover the latest advancements in millimeter-wave and beam-forming technologies, emphasizing their role in enhancing network security and efficiency in automotive vehicles through dual radar communication. Our discussion spans the benefits, applications, challenges, and solutions of these technologies individually from millimeter-wave to beam-forming technology and joint radar communications, alongside a look at their theoretical and practical implementations. We emphasize the integration of beam-forming technology in joint radar communications for future automotive vehicles and its impact on automotive systems, smart cities, and the Internet of Things (IoT). Looking ahead, we discuss the potential of these technologies to transform future tech landscapes, while also addressing the security implications of merging communication and radar capabilities. This paper aims to provide a clear view of the advancements and prospects of millimeter-wave, beam-forming, and dual radar communication technologies.

This paper presents the experimental and numerical study on a ductile beam-column connection between a composite reinforced concrete truss (CRCT) beam and Concrete Filled Tube (CFT) column subjected to bending and shear loads. Two experimental models with different beam-column joint testing schemes, extracted from the same prototype three-dimensional structure designed according to the rules of the capacity design provided by seismic code, were subjected to quasi-static cyclic tests by applying gravitational loads and the horizontal seismic force. The main objective of this paper is to verify the experimental ductile behavior of both specimens and to simulate the experimental global and local response by nonlinear static analysis considering different modelling approaches. The comparison between the experimental and numerical results highlights, for both models considered, the ductile and dissipative capacity of the connection system, designed following the criterion of the hierarchy of resistances proposed by the current Italian code. Different experimental setup showed similar results demonstrating the repeatability of the test and its reproducibility through the nonlinear numerical analysis.

The behaviour of steel frame buildings under progressive collapse conditions depends on a combination of several parameters including the interplay between different collapse resistance mechanisms mobilized in different structural components. Previous studies have shown that the extent to which these mechanisms may contribute to progressive collapse resistance depends on the ability of the beam-column connections to undergo large inelastic deformations prior to reaching their deformation capacity limits. For this reason, and due to the important role of their flexural strength and tying capacity in the development of essential collapse resistance mechanisms, the response of beam-column connections is one of the most important features of progressive collapse performance. Based on the knowledge gained through previous studies on the mechanics of the problem, the role of the connections is critically reviewed by examining the results of several experimental studies conducted during the past decade. The factors that may adversely affect progressive collapse resistance – such as failure modes of certain connection types – are evaluated, and novel approaches of limiting these factors which are currently under development are reviewed. The assessment of these parameters leads to useful conclusions of practical significance, while highlighting the aspects of the problem that need further study and understanding.

Due to the inherent limitations of a single viewpoint, reconstructing 3D human meshes 1 from a single image has long been a challenging task. While deep learning networks enable us to 2 approximate the shape of unseen sides, capturing the texture details of the non-visible side remains 3 difficult with just one image. Traditional methods utilize Generative Adversarial Networks (GANs) 4 to predict the normal maps of the non-visible side, thereby inferring detailed textures and wrinkles 5 on the model’s surface. However, we have identified challenges with existing normal prediction 6 networks when dealing with complex scenes, such as a lack of focus on local features and insufficient 7 modeling of spatial relationships.To address these challenges, we introduce EMAR—Enhanced 8 Multi-scale Attention-driven Single Image 3D Human Reconstruction. This approach incorporates 9 a novel Enhanced Multi-Scale Attention (EMSA) mechanism, which excels at capturing intricate 10 features and global relationships in complex scenes. EMSA surpasses traditional single-scale attention 11 mechanisms by adaptively adjusting the weights between features, enabling the network to more 12 effectively leverage information across various scales.Furthermore, we have improved the feature 13 fusion method to better integrate representations from different scales. This enhanced feature fusion 14 allows the network to more comprehensively understand both fine details and global structures 15 within the image. Finally, we have designed a hybrid loss function tailored to the introduced attention 16 mechanism and feature fusion method, optimizing the network’s training process and enhancing the 17 quality of reconstruction results.Our network demonstrates significant improvements in performance 18 for 3D human model reconstruction. Experimental results show that our method exhibits greater 19 robustness to challenging poses compared to traditional single-scale approaches.

The use of friction-based Beam-to-Column Connections (BCC)s for earthquake-resistant Moment Resistant Frames (MRFs), aiming at eliminating damage to beam end sections due to the development of plastic hinges, has taken hold since the early eighties. Different technical solutions were proposed for steel structures, some were also designed for timber structures, while few more recent studies concern friction joints employed in reinforced concrete structures. Research aimed at characterizing the behavior of joints has focused on the evaluation of the tribological properties of the friction materials, coefficient of friction, shape and stability of the hysteresis cycles, influence of the temperature, speed of load application, effects of the application method, stability of preload, the influence of seismic excitation characteristics on the structural response, statistical characterization of amplitude and frequency of the slip excursion during seismic excitation. Studies aimed at identifying the design parameters capable of optimizing performance have focused attention mainly on the slip threshold, device stiffness, and deformation capacity. This review compiles the main and most recent solutions developed for MRFs. Furthermore, the pros and cons for each solution are highlighted, focusing on the dissipative capacity, shape and stability of hysteresis loops. In addition, the common issues affecting all friction connections, namely characteristics of friction shims and the role of bolt preload, are discussed. Based on the above considerations, a guideline can be outlined, which can help to choose the appropriate solutions for beam-to-column connections for MRFs.

PURPOSE: To investigate the oxylipin profiles in aqueous humor of primary open angle glaucoma (POAG) patients. METHODS: Aqueous humor samples were collected from 17 POAG patients and 15 cataract subjects and subjected to the liquid chromatography-mass spectrometry (LC-MS) analysis to detect the oxylipins. The prediction potential of the differential abundant oxylipins was assessed by the receiver operating characteristic (ROC) curves. Pathway and correlation analyses on the oxylipins and clinical and biochemical parameters were also conducted. RESULTS: The LC-MS analysis detected a total of 76 oxylipins, of which 29 oxylipins reached the detection limit. The multivariate analysis identified 5 differential abundant oxylipins, 15-keto-prostaglandin F2 alpha (15-kPGF2α), Leukotriene B4 (LTB4), 12,13-Epoxyoctadecenoic acid (12,13-Epome), 15-Hydroxyeicosatetraenoic acid (15-HETE) and 11-Hydroxyeicosatetraenoic acid (11-HETE). The 5 oxylipins are enriched in the arachidonic acid metabolism and linoleic acid metabolism pathways. Pearson correlation analysis showed that 11-HETE was positively correlated with intraocular pressure and central corneal thickness and negatively with cup/disk ratio in the POAG patients. In addition, 15-kPGF2α was positively correlated with visual field defect, and LTB4 was negatively correlated with macular thickness.  CONCLUSIONS: This study revealed the oxylipin profile in the aqueous humor of POAG patients. Oxylipins involved in arachidonic acid metabolism pathway could play a role in POAG and anti-inflammatory therapies could be potential treatment strategies for POAG.

The emergence of drug-resistant mycobacteria has rendered many clinical drugs and regimens ineffective, imposing significant economic and healthcare burden on individuals and society. Repurposing drugs intended for treating other diseases is a time-saving, cost-effective, and efficient approach for identifying excellent anti-mycobacterial candidates or lead compounds. This study is the first to demonstrate that rupatadine (RTD), a drug used to treat allergic rhinitis, possesses excellent activity against mycobacteria without detectable resistance, particularly Mycobacterium tuberculosis and Mycobacterium marinum, with a minimal inhibitory concentration as low as 3.13 µg/mL. Furthermore, RTD exhibited moderate activity against nonreplicating M. tuberculosis with the minimal inhibitory concentrations lower than drugs targeting the cell wall, suggesting that RTD has the great potential to be modified and used for the treatment of nonreplicating M. tuberculosis. Additionally, RTD exhibits partial synergistic effects when combined with clofazimine, pretomanid, and TB47 against M. tuberculosis, providing the theoretical foundation for the development of treatment regimens. Transcriptomic profiling leads us to speculate that eight essential genes may be the targets of RTD or may be closely associated with the mycobacterial resistance to RTD. In summary, RTD may be a promising hit for further anti-mycobacterial drug or regimen optimization, especially in case of nonreplicating mycobacteria.

Secondary microplastic (MPL) and nanoplastic (NPL) particles exhibit different physiochemical characteristics that attenuate their toxicities in different ways: some particle types being well documented (primary) while other (secondary), are more unknown. Fourier Transform Infrared Spectroscopy (FTIR), Raman, Proton Nuclear Magnetic Resonance (H-NMR), Curie Point-Gas Chromatography-Mass Spectrometry (CP-gc-MS), Induced Coupled Plasma-Mass Spectrometry (ICP-MS), Nanoparticle Tracking Analysis (NTA), Field Flow Fractionation-Multiple Angle Light Scattering (FFF-MALS), Differential Scanning Calorimetry (DSC), Thermogravimetry (TGA), Differential Mobility Particle [Sizing] (DMPS), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), and Scanning Transmission X-ray Microspectroscopy (STXM) are re-viewed as part of a suite of characterization methods for physiochemical ascertainment and distinguishment. Organizations, like the water treatment or waste management industry, and those in groups that bring awareness to this issue, which are in direct contact with the hydrosphere, can utilize these techniques in order to sense and remediate this plastic polymer pollution. The primary goal of this review paper is to highlight the extent of plastic pollution in the environment as well as introduce its effect on the biodiversity of the planet while underscoring current characterization techniques in this field of research. The secondary goal involves illustrating current and theoretical avenues in which future research needs to address and optimize MPL/NPL remediation, utilizing nanotechnology, before this sleeping giant of a problem awakens.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

With increasing power and speed of laser welding, in-process monitoring has become even more crucial to ensure process stability and weld quality. Due to its low cost and installation flexibility, acoustic process monitoring is a promising method and has demonstrated its effectiveness. Since its feasibility has been the focus of existing studies, the temporal resolution of acoustic emissions (AE) has not yet been addressed despite its utmost importance for realizing real-time systems. Aiming to provide a benchmark for further development, this study investigates the relationship between duration and informativeness of AE signals during high power (3.5kW) and high speed (12m/min) laser beam butt welding. Specifically, the informativeness of AE signals is evaluated based on the accuracy of detecting and quantifying joint gaps for various time windows of signals, yielding numerical comparison. The obtained results show that signals can be shortened up to a certain point without sacrificing their informativeness, encouraging to optimize the signal duration. Our results also suggest that large gaps (> 0.3mm) induce unique signal characteristics in AE, which are clearly identifiable from 1 ms signal segments, equivalent to 0.2mm weld seam.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

Chronic joint inflammatory disorders such as osteoarthritis and rheumatoid arthritis have in common an upsurge of inflammation, and oxidative stress, resulting in progressive histological alterations and disabling symptoms. Currently used conventional medication (ranging from pain-killers to biological agents) is potent, but frequently associated with serious, even life-threatening side effects. Used for millennia in traditional herbalism, medicinal plants are a promising alternative, with lower rate of adverse events and an efficiency frequently comparable with that of conventional drugs. Nevertheless, their mechanism of action is in many cases elusive and/or uncertain. Even many of them have been proved effective in studies done in vitro or on animal models, there is a scarcity of human clinical evidence. The purpose of this review is to summarise the available scientific information on these joint-friendly medicinal plants, which have been already tested in human studies: Arnica montana, Boswelliaspp., Curcuma spp., Equisetum arvense, Harpagophytumprocumbens, Salix spp., Sesamumindicum, Symphytumofficinalis, Zingiberofficinalis, Panaxnotoginseng, Whitaniasomnifera.

This study aimed to explore the feasibility of using airborne acoustic emission in laser beam butt welding for the development of an automated classification system based on neural networks. The focus was on monitoring the formation of joint gaps during the welding process. To simulate various sizes of butt joint gaps, controlled welding experiments were conducted, and the emitted acoustic signals were captured using audible to ultrasonic microphones. To implement an automated monitoring system, a method based on short-time Fourier transformation was developed to extract audio features, and a convolutional neural network architecture with data augmentation was utilized. The results demonstrated that this non-destructive and non-invasive approach was highly effective in detecting joint gap formations, achieving an accuracy of 98%. Furthermore, the system exhibited promising potential for low latency monitoring of the welding process. The classification accuracy for various gap sizes reached up to 90%, providing valuable insights for characterizing and categorizing joint gaps accurately. Additionally, increasing the quantity of training data with quality annotations could potentially improve the classifier model's performance further. This suggests that there is room for future enhancements in the study.

This paper deals with the design and kinematic analysis of a novel mechanism for the elbow joint of an upper-limb exoskeleton, with the aim of helping operators, in terms of effort and physical resistance, in carrying out heavy operations. In particular, the proposed eight-bar el-bow joint exoskeleton mechanism consists of a motorized Watt I six-bar linkage and a suitable RP dyad, which connects mechanically the external parts of the human arm with the corre-sponding forearm by hook and loop velcro and thus, helping their closing relative motion for lifting objects during repetitive and heavy operations. This relative motion is not a pure rotation and thus, the upper part of the exoskeleton is fastened to the arm, while the lower part is not rigidly connected to the forearm, but through a prismatic pair which allows both rotation and sliding along the forearm axis. Instead, the human arm is sketched by means of a crossed four-bar linkage, which coupler link is considered as attached to the glyph of the prismatic pair, that is fastened to the forearm. Therefore, the kinematic analysis of the whole ten-bar mecha-nism, which is obtained by joining the Watt I six-bar linkage and the RP dyad to the crossed four-bar linkage, is formulated to investigate the main kinematic performance and for design purposes. The proposed algorithm has given several numerical and graphical results. Finally, a double-parallelogram linkage, as particular case of the Watt I six-bar linkage, was considered in combination with the RP dyad and the crossed four-bar linkage, by giving a first mechanical de-sign and a 3D printed prototype.

Protected and conserved areas are a key area-based strategy to address the biodiversity and climate change crises. Fundamental to understand their performance over time are indicators. The Digital Observatory for Protected Areas (DOPA) was born in 2013 as a set of open access web services and applications to be used to assess, monitor, and report on protected and conserved areas. For over a decade it has delivered over 50 indicators to support policy processes, national and regional governments, and practitioners. DOPA has also developed a versatile and efficient back-end approach that is widely applicable in other area-based conservation contexts. Here, we describe the methods and workflows behind DOPA´s back end and provide examples of policy relevant questions it can answer. We discuss key advantages and limitations of this systematic and replicable approach and explore the use of this back-end architecture to inform progress in area-based conservation targets for the following decades. This approach, embedded in multiple services provided by the Knowledge Centre for Biodiversity of the European Commission (KCBD), can also support the implementation and monitoring of area-based targets of the Kunming Montreal Global Biodiversity Framework at international, regional, and national levels.

Background. Escalating global plastic production, expected to reach 34,000 million tons by 2050, poses a significant threat to human and environmental well-being, particularly in aquatic ecosystems. Microplastics (MP) and nanoplastics (NP), which originate from the degradation of plastics, are of concern due to their potential bioaccumulation and uptake of pollutants. This study addresses identification methods and focuses on insect meal, a raw material for aquaculture feed. Methods. By using different techniques, the study was able to detect MP and NP in insect meal samples. Chemical digestion with KOH at 60°C efficiently removed organic matter without affecting the synthetic polymer polyethylene (PE). Filtration, confocal Raman microscopy, SEM and TEM were used for comprehensive analysis and integrity tests on PE films were performed using Raman and FTIR spectroscopy. The results showed the presence of PE microplastic particles in the insect meal, which was confirmed by correlative Raman and SEM mapping on a positively charged surface. In addition, the increased resolution of the Raman microscope identified submicrometric PE NP (800 nm). Transmission electron microscopy (TEM) with energy dispersive X-ray spectroscopy (EDX) confirmed plastic-like structures in the insect meal, highlighting the presence of PE plastics characterized by irregular shapes and some agglomeration. The higher carbon concentration in the EDX analysis supported the plastic nature, which was also confirmed by Raman spectroscopy. Conclusions. The study provides a robust method for the detection of MP and NP in insect meal and provides valuable insight into the possible presence of plastics in insect-based aquafeeds. The combination of different analytical methods increases the reliability of the results and sets the stage for future investigations that could focus on the quantification of NP and the assessment of their potential environmental impact.

The effect of wave forces on the structural safety of fixed oscillating water-column (OWC) devices is critical. In this study, a three-dimensional numerical model of an oscillating water column (OWC) device is constructed using the computational fluid dynamics software OpenFOAM. Subsequently, the hydrodynamic performance of the numerical model is comprehensively validated. Finally, the hydrodynamic performance data are analyzed in detail to obtain meaningful conclusions. The results indicate that the horizontal wave force on the OWC device is approximately 6.6 to 7.9 times greater than the vertical wave force, whereas the lateral wave force is relatively small. Both the horizontal and vertical wave forces decrease as the relative water depth increases under a constant wave period and height. The horizontal wave force increases linearly with the wave height, whereas the vertical wave force increases with the square of the wave height. In addition, the highest dynamic water pressure is observed at the interface between the water surface and device, both within and outside the front wall of the gas chamber. The dynamic water pressure at different locations on the front chamber increases and subsequently decreases as the wave frequency increases.

African swine fever virus (ASFV) continues to spread globally causing severe economic losses to the pig farmers. Vietnam licensed two live attenuated vaccines based on the ASFV strains ASFV-G-ΔI177L and ASFV-G-ΔMGF, to control the ongoing ASF outbreaks. In 2023, newly emerging highly virulent recombinant ASFV viruses containing genetic elements from both ASFV p72 genotype I and II (rASFV I/II) strains were reported from Northern Vietnam. This study evaluated if the two vaccine strains were able to protect the pigs against the emerging rASFV I/II strain VNUA/rASFV/TN1/23. Pigs vaccinated with ASFV-G-ΔMGF or ASFV-G-ΔI177L, when challenged with rASFV I/II, succumbed to the infection, or developed signs of chronic ASF. The findings from this study show that both vaccine strains that are licensed and used in Vietnam, are unlikely to protect pigs from the emerging highly virulent rASFV I/II strains. This complicates the ongoing efforts to control ASF in Asia and globally and emphasizes the urgent need for a novel vaccine that can effectively protect pigs from the rASFV I/II strains.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Acetamiprid is a broad-spectrum neonicotinoid insecticide used in agriculture to control aphids. While recent studies have documented resistance to acetamiprid in several aphid species, the underlying mechanisms are still not fully understood. In this study, we analyzed the transcriptome and metatranscriptome of a laboratory strain of the pea aphid, Acyrthosiphon pisum (Harris, 1776), with reduced susceptibility to acetamiprid after nine generations of exposure to identify candidate genes and the microbiome involved in the adaptation process. Sequencing of the transcriptome of both selected (RS) and non-selected (SS) strains allowed the identification of 14858 genes and 4938 new transcripts. Most of the differentially expressed genes were associated with catalytic activities and metabolic pathways involving carbon and fatty acids. Specifically, the alcohol-forming fatty acyl-CoA reductase (FAR) and acyl-CoA synthetase (ACSF2), both involved in the synthesis of epidermal wax layer components, were significantly upregulated in RS, suggesting that adaptation to acetamiprid involves the synthesis of a thicker protective layer. Metatranscriptomic analysis revealed subtle shifts in the microbiome of RS. These results contribute to a deeper understanding of acetamiprid adaptation by the pea aphid and provide new insights for aphid control strategies.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In the paper, we prove a joint limit theorem in terms of weak convergence of probability measures on $\mathbb{C}^2$ defined by means of the Epstein ζ(s;Q) and Hurwitz ζ(s,α) zeta-functions. The limit measure in the theorem is explicitly given. For this, some restrictions on the matrix Q and parameter α are required. The theorem obtained extends and generalizes Bohr-Jessen’s results characterising asymptotic behaviour of the Riemann zeta-function.

Background and Objectives: Fibrillinopathies have different phenotypic expression: Marfan- like skeleton features, MLSF; mitral valve prolapse syndrome, MVPS; MASS phenotype, M= mitral valve prolapse, MVP, A= aortic root dilation, S= skeletal features, and the second S= (cutaneous) striae; Marfan syndrome, MS. These are inherited connective tissue diseases, provoked by a mutation of the encoding gene for a protein(fibrillin 1, FBN1) which has major importance in the formation of elastic fibers.The study had the following main objectives: the correlation between disc displacement, DD( a major sign for temporomandibular joint dysfunction, TMD) on magnetic resonance imaging, MRI, and aortic Z score(a major sign for aortic root dilation) on echocardiography; the predictive value of DD towards aortic Z score. DD had 2 types of severity: DD with reduction(the mild type, DDwR) , and DD without reduction( the severe type, DDwoR). Materials and Methods: The type of fibrillinopathy was precised by clinical exam( systemic score), ophthalmic exam(for ectopia lentis), and echocardiography(aortic Z score, MVP). Medical treatment consisted in betablockers, BB(for patients with tachycardia), or angiotensin II receptor blockers, ARB. Surgical treatment was addressed to aortic root aneurysm, and severe MR. DD benefited by dental conservatory treatment, or surgical restoration.Results: DD- Z score had a powerful correlation in MASS(Rho= 0.787, p< 0.01), and in MS patients(Rho=0.819, p< 0.01). For the entire sample, both DDwR- Z score, and DDwoR- Z score had a moderate correlation(Rho= 0.469, and respectively 0.669). Muchmore, DD was an important predictor for Z score. DDwoR had a double power of prediction for Z score, comparative with DDwR(B coefficient= 1.661 for DDwR, and 3.281 for DDwoR). Conclusions: TMD had a powerful correlation with aortic root dilation, in MASS, and MS patients from the sample. Likewise, TMD was a major predictor for aortic root dilation, in the entire sample. We can utilize in clinical practice, an extracardiac finding, TMD, obtained by a non-invasive technique, MRI, for cardiac severity stratification of fibrillinopathies.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

Weight-bearing computed tomography (WBCT) enables acquisition of three dimensional bony structure images in a physiological weight-bearing position, which is fundamental in under-standing the pathologic lesions and deformities of the ankle joint. Over the past decade, re-searchers focused on validating and developing WBCT measurements, which has significantly enhanced our knowledge of common foot and ankle disease. Consequently, understanding the application of WBCT in clinical practice is becoming more important to produce improved out-comes in the treatment of disease around the ankle joint. This review will describe an overview of what is currently being evaluated in the foot and ankle surgery using WBCT and where the course of research will be heading in the future.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

This study presents a detailed investigation of the application of superquadrics in small-angle scattering (SAS), a technique essential in materials science, biology, and physics for investigating structural properties at the nanoscale and microscale. Superquadrics, a family of geometric shapes known for their versatility in representing a wide range of forms, are employed to model complex structures in SAS studies. We examine the parametric nature of superquadrics and their ability to efficiently describe shapes from simple balls to intricate star-like forms. We demonstrate the application of superquadrics through a rigorous analysis of SAS simulated data, including scattering intensity patterns and pair-distance distribution functions. This allows us to reveal insights into key structural characteristics of various materials, such as the size and shape. We also demonstrate the efficacy of superquadrics in accurately modeling experimental small-angle X-ray scattering data from a chimeric protein complex, showcasing their potential in biological systems analysis. The findings offer a robust framework for future research and application in diverse fields, including materials science, nanotechnology, and bioengineering.

Microwave technology has a potential application in the extraction of zinc from sulphide ores, knowledge of the dielectric properties of these ores plays a major role in the microwave design and simulation for any process. The dielectric properties of zinc sulfide concentrate for two different apparent densities—1.54 and 1.63 g/cm³—have been measured by using the resonance cavity perturbation technique at 915 and 2450 MHz during the roasting process for the temperature ranging from room temperature to 850 °C. The variations of dielectric constant, the dielectric loss factor, the dielectric loss tangent and the penetration depth with the temperature, frequency and apparent density have been investigated numerically. The results indicate that the dielectric constant increases as the temperature increases and temperature has a pivotal effect on the dielectric constant, while the dielectric loss factor has a complicated change and all of the temperature, frequency and apparent density have a significant impact to dielectric loss factor. Zinc sulfide concentrate is high loss material from 450 to 800 °C on the basis of theoretical analyses of dielectric loss tangent and penetration depth, its ability of absorbing microwave energy would be enhanced by increasing the apparent density as well. The experimental results also have proved that zinc sulfide concentrate is easy to be heated by microwave energy from 450 to 800 °C. In addition, the experimental date of dielectric constant and loss factor can be fitted perfectly by Boltzmann model and Gauss model, respectively.

In the last decades, numerous studies indicated the substantial role semiconductors could play in photocatalytic processes for environmental applications. Materials that contain a semi-conductor as a photo-catalyst have a semi-permanent capacity for removing harmful gases from the ambient air. In the present work, the focus is on TiO2. Heterogeneous photo-catalysis using TiO2 leads to the degradation of NO/NO2, benzene, toluene, and other priority air pollutants once in contact with the semiconductor surface. Preliminary evidence indicates that TiO2 containing construction materials and paints efficiently destroy the ozone precursors NO and NO2 up to 80% and 30%, respectively. Therefore, the development of innovative coatings containing TiO2 as a photo-catalyst was in the foreground of research activities with the aim to be used as building and construction materials mainly outdoors, e.g. on building facades in high traffic roads for the degradation of priority air pollutants (NOx and volatile organic compounds) in the polluted urban atmosphere. Though the advantages connected with the application of TiO2 due to its band gap of 3.2 eV are limited. TiO2 is effective only in the UV-region (ca. 5%) of the solar spectrum with wavelengths λ

Vibration problems have become one of the most important factors affecting robot performance. To this end, a terminal residual vibration suppression method based on joint trajectory optimization is proposed to improve the accuracy and stability of robot motion. Firstly, based on the characteristics of the friction nonlinearity due to joint coupling and physical feasibility of dynamic parameters, a semidefinite programming method is used to identify dynamic parameters with actual physical meaning, thereby obtaining an accurate dynamic model. Then, based on the result of the residual vibration time domain analysis, a joint trajectory optimization model with the goal of minimizing joint tracking error is established. The Chebyshev collocation method is used to discretize the optimization model. The dynamic model is used as the optimization constraint, and barycentric interpolation is used to obtain the optimized joint motion trajectory. Finally, industrial robot experiments prove that the vibration suppression method proposed in this article can reduce the maximum acceleration amplitude of residual vibration by 62% and the vibration duration by 71%. Compared with the input shaping method, the method proposed in this paper can reduce the terminal residual vibration more effectively and ensure the consistency of running time and trajectory.

During choriogenesis in insects, chorion (eggshell) is formed by surrounding follicular epithelial cells in ovarioles. However, the regulatory endocrine factor(s) activating choriogenesis and the chemical components on eggshell deserve further exploration. In two representative Coleopterans, a Coccinellid Henosepilachna vigintioctopunctata and a Chrysomelid Leptinotarsa decemlineata, genes encoding the 20-hydroxyecdysone (20E) receptor heterodimer, ecdysone receptor (EcR) and ultraspiracle (USP), and two chitin biosynthesis enzymes UDP-N-acetylglucosamine pyrophosphorylase (UAP) and chitin synthase (ChS1), were highly expressed in ovaries of the young females. RNA interference (RNAi)-aided knockdown of either HvEcR or Hvusp in H. vigintioctopunctata inhibited oviposition, suppressed the expression of HvChS1, and lessened the positive signal of Calcofluor staining on the chorions, which suggests the reduction of a chitin-like substance (CLS) deposited on eggshells. Similarly, RNAi of LdEcR or Ldusp in L. decemlineata constrained oviposition, decreased the expression of LdUAP1 and LdChS1, and declined CLS contents in the resultant ovaries. Knockdown of LdUAP1 or LdChS1 caused similar defective phenotypes, i.e., reduced oviposition and CLS contents in the L. decemlineata ovaries. These results, for the first time, indicate that 20E signaling activates choriogenesis in two Coleopteran species. Moreover, our findings propose the deposition of a CLS on the chorions.

Asymmetric lithium salts, such as Lithium (difluoromethanesulfonyl)(trifluoromethanesulfonyl)imide (LiDFTFSI), have been demonstrated to surpass traditional symmetric lithium salts with improved Li+ conductivity and the capacity to generate stable solid electrolyte interphase (SEI) while maintaining compatibility with aluminum (Al0) current collector. However, the intrinsic reductive mechanism through which LiDFTFSI influences battery performance remains unclear and under debate. Herein, the detailed SEI reactions of LiDFTFSI-based electrolytes were investigated by combining density functional theory and molecular dynamics, aiming to clarify the formation process and atomic structure of SEI. Our results show that asymmetric DFTFSI– weakens the interaction between carbonate solvents and Li+, and substantially alter the solvation structure, exhibiting a well-balanced coordination capacity to bis(trifluoromethanesulfonyl)imide (TFSI–). Nanoseconds hybrid molecular dynamics simulation further reveals that the preferential decomposition of LiDFTFSI produces sufficient LiF and Li2O to facilitate a robust SEI. Moreover, the abundant F– generated from LiDFTFSI decomposition accumulates on the Al surface and subsequently combines with Al3+ from the current collector to form AlF3, potentially inhibiting corrosion of the current collector. Overall, these findings elucidate how LiDFTFSI regulates the solvation sheath and SEI structure, advancing the development of high-performance electrolytes compatible with current collector.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

A printed Vivaldi antenna that is optically transparent, ultra-wideband (UWB), and reconfigurable has been developed, fabricated, and tested at millimeter wave frequencies. It covers a broad frequency range of 20-30 GHz by using three PIN diodes. The diodes control the current flow to direct the beam of the antenna. The results of numerical simulations and measurements match at millimeter wave frequencies. The design of this antenna is unique as it allows for a reduction in size and ease of integration while also providing the ability to change the radiation pattern by up to 300 degrees, making it suitable for 5G and 6G communications. Additionally, this antenna can also be useful for RF applications that require dynamic switching of radiation patterns and cognitive radio.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

(1) Background: The significant progress observed over last two decades in coherent beam combining (CBC) technology has mainly focused on its applications in high-energy physics and laser weapons. This work provides insight into the basic principles of CBC and the search for an alternative, namely optical angular momentum (OAM) generation using CBC; (2) Methods: The semi-analytical model based on the paraxial wave equation explored generating OAM-CBC beams by manipulating the tilts and phases of CBC (T&P-CBC) of hexagonal architecture; (3) Results: The specially arranged T&P-CBC shows typical properties of OAM, such as annular profiles for the zero diffraction order and 1-st order replicas in the far field and correlation coefficients of 1% between different OAM-CBC fields; (4) Conclusions: The differences between classical OAM beams and OAM-CBC are substantial due to hexagonal lattice properties. Moreover, applications in free space optical communications are feasible as T&P CBC fulfills the main conditions and requirements for OAM generation.

The catastrophic failure of two dams in Libya in the night of 10th and 11th September 2023, resulted in a significant amount of water and debris destroying a large part of the city of Derna, which is located downstream of the two dams. The flood caused more than 6000 fatalities and the dis-placement of thousands of people from the city. The dams failed due to heavy rainfall caused by the Medicane Daniel, resulting in intense precipitation and the dams overspilling after reaching full capacity. This paper analyses the consequences of the dam breach by modelling the flow discharge and the flooding of the city of Derna. The analysis compares the computed quantities with the findings of the post-event satellite image analysis from UNOSAT and Copernicus, the field reports, and information gathered from the social media through AI detection. The results allows to better understand the dynamics of the dam breach, its initial parameters and an assessment of the accu-racy of the results.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

The tumor necrosis factor receptor associated factor 1 (TRAF1) plays a key role in promoting lymphocyte survival, proliferation, and cytokine production. Recent evidence showed that TRAF1 plays opposing roles in monocytes and macrophages where it controls NF-B activation and limits pro-inflammatory cytokine production as well as inflammasome-dependent IL-1 secretion. Importantly, TRAF1 polymorphisms have been strongly linked to an increased risk of rheumatoid arthritis (RA). However, whether and how TRAF1 contributes to RA pathogenesis is not fully understood. Moreover, investigating the role of TRAF1 in driving RA pathogenesis is complicated by its multifaceted and opposing roles in various immune cells. In this study, we show that intraarticular injection of TRAF1 deficient macrophages into knee joints of wildtype (WT) mice subjected to the collagen antibody induced arthritis (CAIA) model of RA significantly exacerbated joint inflammation, immune cell infiltration and tissue damage compared to mice injected with WT macrophages. This study may lay the groundwork for novel therapies for RA that target TRAF1 in macrophages.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

The next generation network requires not only ultra high data rate, global coverage and connectivity, but also reducing network deployment costs and energy consumption. The emergence of reconfigurable intelligent surface (RIS) technology provides an effective way to improve efficiency and reduce cost, while the passive elements bring new challenges of channel estimation (CE) and beam tracking. For a RIS-aided multiple-input and single-output (MISO) system, in this paper, to achieve the channel state information (CSI), we propose a principle component analysis (PCA) based staged channel estimation method. Based on the estimated channel, we propose a deep learning (DL) based beam tracking scheme to realize low-complexity RIS reflection coefficient design, which effectively improves the signal-to-noise ratio (SNR) at the user side. Simulation results verify our proposed channel estimation scheme based on PCA and beam tracking scheme based on DNN for the semi-active RIS-aided MISO systems can obtain approximate performances with much lower computational complexity.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Oritavancin is a novel long-acting lipoglycopeptide with in vitro activity against methicillin-resistant (MR) Gram-positive pathogens and a good bactericidal activity even in presence of biofilm forming bacteria. It has been approved for acute bacterial skin and skin structure infections (ABSSSI), but recent reports have demonstrated possible off-label uses, as for prosthetic joint infections (PJI), which, in more than half of cases, are caused by MR Gram positive organisms. We reported a case of a man in his eighties with a late shoulder PJI caused by methicillin resistant Staphyloccus epidermidis (MRSE) with contraindications for surgical replacement and few oral therapeutic options for a long term suppressive antibiotic therapy. The prosthesis was retained, and the patient received ten outpatient sequential doses of 1200 mg of oritavancin during 28 weeks, based on therapeutic drug monitoring (TDM) as a guide for correct timing of administration of each dose. During oritavancin administration, the patient achieved clinical cure, with disappearance of the pain and regaining pre-infection joint mobility, with no side effects reported and no further surgery or hospitalization needed. The treatment is ongoing as a long-lasting suppressive antimicrobial therapy. Oritavancin could represent an excellent solution for treating PJI caused by MR organism, especially in patients who need a long-term suppressive therapy.

Evaluation ecosystem service value (ESV) is critical for “lucid waters and lush mountains are invaluable assets”. However, the ESV estimation and spatial-temporal analysis for mountainous soil erosion area is rare, e.g., Changting county, China. In this study, we developed a remote sensing driven mountainous equivalent factor (RS-MEF) method to estimate the ESV of soil erosion area in subtropical mountain. It is a hybrid of a conventional equivalent factor framework and the remote sensing techniques for mountains, and achieves several highlights of spatial adjustment using carbon sink with vegetation canopy, improvement spatial resolution, and removal topographic effect. Using the RS-MEF method, we estimated that the ESV of Changting county was about 15.80 billion CNY in 2010 and 34.83 billion CNY in 2022. Specifically, the ESV per unit area of major soil erosion area (MSEA) in the county was less than that of non-major soil erosion area (n-MSEA), however, the ESV growth rate of MSEA from 2010 to 2022 was faster than that of n-MSEA. Therefore, the ESV gap between two areas was shortened from 28.99% in 2010 to 15.83% in 2022. Topographic gradient effect analysis illustrates that the area with high elevation and small slope is one control focus in the next step. Our study indicates that the ecological restoration in the county has made great achievements in the ESV perspective, with low ESV area shrank evidently in MSEA; and the achieved knowledge of the ESV growth and inherent factors is valuable and instructive for the next soil and water conservation.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

This study aimed to clarify the relationship between the joint and ligament structures of the subtalar joint and degeneration of the subtalar articular facet. We examined 50 feet from 25 Japanese cadavers. The number of articular facets, joint congruence, and intersecting angle were measured for the joint structure of the subtalar joint, and the footprint areas of the ligament attachments of the cervical ligament, interosseous talocalcaneal ligament (ITCL), and anterior capsular ligament were measured for the ligament structure. Also, subtalar joint facets were classified into Degeneration (+) and (-) groups according to degeneration of the talus and calcaneus. No significant relationship was identified between the joint structure of the subtalar joint and degeneration of the subtalar articular facet. In contrast, footprint area of the ITCL was significantly higher in the Degeneration (+) group than in the Degeneration (-) group for the subtalar joint facet. These results suggest that the joint structure of the subtalar joint may not affect degeneration of the subtalar articular facet. Degeneration of the subtalar articular facet may be related to the size of the ITCL.

At present, diversified and highly concurrent businesses in the Internet industry often require heterogeneous databases formed by multiple databases to meet the needs. This report introduces database kernel SG-ColBase we developed. After achieving read and write concurrency control, data rollback, atomic log writing, and downtime data redo to ensure complete transaction support. The parallelism of database kernel execution is extended through field level locks and snapshot reads. Use the Bloom filter, resource cache pool, memory pool, skip list, non blocking log cache, and asynchronous data writing mechanism to improve the overall execution efficiency of the system. In terms of data storage, column storage, logical key and LSM-tree are introduced. While improving the data compression ratio and reducing data gaps, all disk data operations are written in incremental order. With the characteristics of asynchronous batch operation, the data writing speed is greatly improved. Thanks to the continuous feature of vertical data brought by column storage, the disk scanning brought by vertical traversal is reduced, which is a qualitative leap in efficiency compared with traditional relational databases in the big data analysis scenario. SG-ColBase can reduce the use of heterogeneous databases in business and improve R&D efficiency.

This study addresses the enhancement of material efficiency and reduction of brittleness in timber-to-concrete adhesive connections for beam-type timber and timber-concrete composite panels. The research explores the potential benefits of adding longitudinal timber ribs to Cross-Laminated Timber (CLT) beam-type panels. Three groups of flexure-tested specimens were analysed: (1) timber panels (1400 mm × 400 mm) with two 100 mm thick CLT panels and two 60 mm thick CLT panels reinforced with 150x80 mm timber ribs; (2) eight specimens (600 mm × 100 mm × 150 mm) with CLT members (600 mm × 100 mm × 100 mm) connected to a 50 mm concrete layer using granite chips and Sikadur-31 (AB) epoxy adhesive; (3) six CLT panels (1400 mm × 400 mm × 50 mm) bonded to a 50 mm concrete layer, with two panels containing polypropylene microfibers and two panels incorporating polyethene dowels for mechanical connection. Specimens were subjected to three-point bending tests and analysed using the transformed section method, γ-method, and finite element method with ANSYS 2023R2 software. Results indicated a 53% increase in load-carrying capacity for ribbed CLT panels with no additional material consumption, a 24.8%-41.1% increase for CLT panels strengthened with a concrete layer, and improved ductility and prevention of disintegration in timber-concrete composites with polypropylene microfibers.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Models of subsurface structures are important for successful deposit exploration but are challenged by the need to integrate data from different geophysical methods. In the present study, we evaluated a method of joint inversion in which audio-magnetotelluric (AMT) and dual frequency induced polarization (DFIP) data sets are inverted simultaneously to produce a consistent 2D resistivity model to show a clear image of subsurface structures. To achieve the objectives, we conducted AMT and DFIP surveys first on the same survey line within the Dongjun lead-zinc deposit in inner Mongolia by developing 31 AMT survey sites with an interstation separation of 40 m on a 1440 m survey track and operated in fifty-three frequencies in the range 1–10,400 Hz to record the resistivity distribution of subsurface to depths exceeding 800 m. The same survey setup up was applied to the DFIP method by utilizing the SQ-3C model with a pole-dipole array configuration and conducted measurements at frequencies of 4 Hz and 4/13 Hz. We first separately inverted AMT and DFIP measurements. The two-dimensional (2D) model obtained from AMT data revealed distinct low resistivity anomalies in the middle of the 2D inversion model. In contrast, the DFIP inversion model showed a high resistive body in the same region. In response to the discrepancies observed in the separate 2D inversion models, we implemented a joint inversion for both the AMT and DFIP datasets. The joint inversion resistivity model shows surficial conducting bodies and a high conductive body along the profile with relatively high Percent Frequency Effect (PEF) indicating high chargeability. The final joint inversion resistivity model clearly images the large silica alteration zone and the Pb-Zn mineralization. This study demonstrates the feasibility of a joint inversion methodology and highlights the value of integrating geophysical methods through joint inversion for enhanced characterization and exploration of lead-zinc ores.

With the large-scale application of Internet of Things (IoT) in the medical field, eHealthcare has attracted wide attention. With the help of IoT devices, eHealthcare allows doctors to monitor patients’ health conditions and make recommendations accordingly. The addition of cloud computing greatly saves Healthcare Center’s (HC) computing resources. In order to provide privacy and fine-grained access control, Attribute-b ased encryption (ABE) is widely favored. HC usually operates multiple medical institutions in different regions, and each medical institution can be regarded as a attribute authority. Therefor, multi-authority (MA) ABE is usually concerned to encrypt the patient data. However for existing MA-ABE algorithms, the ciphertext is long and the efficiency of encryption and decryption is low. These problems will greatly increase the computing burden of patients and seriously affect the efficiency of data transmission. Hence we propose a decentralized key-policy MA-ABE in eHealthcare. The proposed algorithm can achieve decentralization, that is, it does not need central authority. Meanwhile, compared with existing MA-ABE algorithms, the length of ciphertext generated by our algorithm is shorter, and the efficiency of encryption and decryption is significantly improved. With the help of Java Pairing Based Cryptography, we carried out the experiments which show that our algorithm can effectively reduce the time required for encryption and decryption.

The joint extraction of entities and relations is a critical task in information extraction, and its performance directly affects the performance of downstream tasks. However, existing joint extraction models based on deep learning exhibit weak processing capabilities for the phenomenon of multiple pronunciations of one character and multiple characters of one pronunciation when processing Chinese texts, resulting in performance loss. To address these issues, this paper introduces part-of-speech (POS) and pinyin features to aid the model in learning semantic features that are more contextually appropriate. A Chinese Joint Entity and Relation Extraction Model based on Progressive Contrastive Learning and Heterogeneous Feature Fusion is proposed (CJE-PCHF). During model training, an interactive fusion network based on progressive contrastive learning is employed to learn the dependencies between pinyin, POS, and semantic features. This guides the model in heterogeneous feature fusion, capturing higher-order semantic associations between heterogeneous features. On the commonly used DuIE evaluation dataset for joint extraction, this model achieved a significant improvement, with the F1 score increasing by 5.4% compared to the benchmark model CasRel.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

In the present paper four passive micromixers designs (G1, G2, G3 and G4) inspired on distillation columns trays were proposed. The devices performance was assessed by numerical simulations. The mixing performance was investigated for a Reynolds number range from 0.01 to 100 and channel height of 200 µm, 500 µm and 1000 µm for oil/ethanol flow. G1 and G4 designs provided high mixing index (> 0.975). The G1 device achieved superior mixing performance with a moderate pressure drop (about 0.5 MPa) due to the induced flow recirculation pattern for a relative high flow rate of 0.21 L/min, highlighting the potential use of such microdevice for scale-up and numbering-up of microdevices in modular chemical plant processing.

Purpose: Investigation for the co-occurrence of two unrelated genetic disorders of muscular dystrophy and Prader-Willi syndrome (PWS) (OMIM # 176270) using joint whole genome sequencing (WGS). Methods: Trio WGS joint analysis was performed to investigate the genetic etiology in a proband with PWS, prolonged muscular hypotonia associated hyperCKemia, and early-onset obesity. The parents were unaffected. Results: Results showed maternal isodisomy uniparental disomy (UPD) in chromosome 15 expanding from 15q11.2 to 15q22.2, including PWS regions at 15q11.2-15q13. Maternal heterodisomy was detected from 15q22.2 to 15q26.3. A pathogenic variant, NM_000070.3(CAPN3):c.550del (p.Thr184fs), was identified at 15q15.1 in a heterozygous state in the mother that was homozygous in the proband due to maternal isodisomy. Conclusion: This is the first study of the concurrent molecular etiology of PWS and calpainopathy (OMIM # 253600) in the same patient. This report highlights the utility of joint analysis and need for the assessment of autosomal recessive disease in regions of isodisomy in patients with complex and unexplained phenotype.

Objective. The present study examined the potential use of computed tomography panoramic mandibular indices on cone beam CT (CBCT) for the assessment of bone density in postmenopausal women with low bone mass. Study design. We enrolled 104 postmenopausal women who performed dual energy X-ray absorptiometry (DXA) using a DXA scanner and mental foramen region CBCT using NewTom VGi EVO Cone Beam 3D system. We assessed the relationship between DXA parameters: lumbar, femoral neck and total hip T score, bone mineral density (BMD), and lumbar trabecular bone score (TBS) and the panoramic mandibular indices: computed tomography mandibular index superior (CTI(S)), computed tomography mandibular index inferior (CTI(I)) and computed tomography mental index (CTMI). Results. We found important correlations between the CTI(I), CTI(S) and CTMI and bone mass, quantitative evaluated as BMD and T-score and also quality using TBS score. Conclusion. CBCT measured indices CTI(S), CTI(I), CTMI are useful in assessing patients with low bone mass.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

Since cART was introduced to treat AIDS, the mortality rate due to AIDS has markedly decreased and the convalescence of HIV-infected individuals has improved drastically. However, HIV-1 sexual transmission has made HIV become a global epidemic. Sacran is a megamolecular poly-saccharide extracted from cyanobacterium Aphanothece sacrum that exhibits numerous desirable characteristics for transdermic applications, such as safety as a biomaterial, a high moisture re-tention effect, the ability to form a film and hydrogel, and an anti-inflammatory effect. In this study, we evaluated the anti-HIV-1 effects of Sacran as a barrier to HIV transmission. Sacran inhibited HIV-1 infection and envelope-dependent cell-to-cell fusion. Moreover, we used a Transwell assay to confirm that sacran inhibited viral diffusion and captured viruses. The synergistic effects of sacran and other anti-HIV infection drugs were also evaluated.HIV-1 infections can be reduced through the synergistic effects of sacran and anti-HIV-1 drugs. Our study suggests the use of sacran gel to protect against HIV-1 transmission.

The velocity distribution of flow in an eccentric cylindrical annulus is determined in an attempt to investigate the vertical capillary rise in the channel. The radii ratio and the eccentricity at which a transition from monotone to oscillatory rise occurs, are determined. The results are shown to converge to the well-known limiting cases of concentric annuli and circular tubes.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

In order to develop novel botanical insecticides, the joint action of Ligusticum chuanxiong oil (LCO) and lemongrass oil (LO) against Aphis citricola van der Goot was determined systematically indoors and outdoors. The chemical profiles of LCO and LO as determined by gas chromatography- mass spectrometry analysis revealed that main compounds from LCO were Z-Ligustilide (44.58%) and Senkyunolide A (26.92%), and that of LO were geranial (42.16%) and neral (32.58%), respectively. The mixture of LCO and LO showed significant synergy against A. citricola, with a common-toxicity coefficient (CTC) value of 221.46 at the optimal ratio of LCO to LO (4: 1, w/w). Based on the results of solvents and emulsifiers screening, L. Chuanxiong oil · Lemongrass oil 20% emulsifiable concentrate (20% LCO · LO EC) was developed, which was confirmed to meet the requirements of a commercial pesticide by quality test. Field trials indicated that the insecticidal activity of the diluted 20% LCO · LO EC (1000 fold dilution) was comparable to conventional pesticide (20% imidacloprid EC) on A. citricola 7 days after application. Thus, the mixture of LCO and LO has the potential to be further developed as a botanical pesticide.

Purpose To investigate the effects of intra-articular glenohumeral joint triamcinolone injection in treating secondary adhesive capsulitis after breast cancer surgery.Methods This study prospectively enrolled 37 participants, 22 of the breast cancer surgery group and 15 of the idiopathic group. All participants received intra-articular glenohumeral joint injection in the affected shoulder joint and received physiotherapy for 12 week. The clinical assessment evaluated before, and 1, 3, and 6 months after the intervention. The primary outcome was the change in the Shoulder Pain and Disability Index (SPADI).Results The total SPADI(%) in both groups showed significant decrease from baseline to 1, 3, and 6 months after the intervention. There was no significant difference in the differences of the total SPADI from baseline to 1, 3, and 6 months between two groups. However, the improvement in the SPADI pain subscale and the PROM of abduction at 3 and 6 months post-injection in the breast cancer group were inferior to the idiopathic group.Conclusion Intra-articular triamcinolone injection for adhesive capsulitis after breast cancer surgery significantly improved in significant improvements of pain, shoulder function and the PROM. The effects were similar to idiopathic adhesive capsulitis, but in the breast cancer surgery group, appropriate pain and ROM management and monitoring are required even 3 months after injection. With a standardized injection protocol, intra-articular triamcinolone injection could be an effective and safe treatment option for secondary adhesive capsulitis after breast cancer surgery.

Background: This study aimed to investigate the association between the internal derangement of the temporomandibular joint (TMJ), in particular the severity of disc displacement (DD), and the presence of generalized joint hypermobility (GJH) in growing patients evaluated on magnetic resonance images (MRI). The study also investigated the relationship between the stages of DD severity and age. Methods: This cross-sectional study has been conducted on a pre-orthodontic population (8-16 years). The GJH was assessed with the Beighton test (cutoff ≥ 4) and the final sample of 56 patients was divided into two groups: a Study Group, 30 subjects with GJH, and a Control Group, 26 subjects without GJH. The disc position was evaluated on MRI and the severity of DD was classified in four stages. Pearson's χ2 Test was performed for the analysis of the statistical correlation. Results: A statistically significant relationship between GJH and disc position was found, in particular a disc displacement with reduction (DDwR) and DD severity. It also emerged a positive association between the severity of DD and age, that increased with increasing age. Conclusions: Growing patients with GJH have a higher risk of developing DD and with more severe stages. The risk of developing DD and the severity increases with increasing age.

Resonance inductive coupling is widely used for wireless power transfer (WPT) in medical applications. In this paper, we analyze the LCL-compensated WPT structure and propose a novel constant voltage transmission system based on gain estimation, without any extra feedback from the receiver. The system is capable for implant neural stimulation where the load impedance and the coupling coefficient are both variable. Compared to existing methods for constant voltage transmission, our approach offers advantages in compact size and the compatibility with the industrial, scientific and medical (ISM) band. We validate the load-independent resonant characteristic and the feasibility of constant voltage transmission using an experimental prototype working at 6.78MHz. Finally, we discuss the structure of the implant stimulator and methods of applying the proposed WPT system.

In this study, the team employed full-scale crash tests to investigate the impact of post-densification technology on the safety performance of separated central median W-beam barriers under low compaction conditions. By precisely simulating the design and construction environment of the central median, the study comprehensively evaluated the barrier's containment, redirection, buffering, and anti-intrusion performances, as well as the deformation of both the barrier and vehicles under various collision scenarios. The results indicate that under low compaction soil conditions, the A-level separated central median barriers reinforced with post-densification technology effectively meet the specified protection requirements. By comparing the influence of soil strength variations on barrier performance under simulated rainfall conditions, it was confirmed that enhancing soil compaction significantly improves soil stability, effectively increases the overall strength and stability of the barriers, reduces deformation, and significantly enhances safety performance. This study not only validates the effectiveness of the reinforcement scheme but also provides new perspectives for the scientific research of safety barriers and offers crucial technical support for the optimal design of road safety protection facilities.

The dorsal column nuclei complex (DCN-complex) includes the dorsal column nuclei (DCN, referring to the gracile and cuneate nuclei collectively), external cuneate, X, and Z nuclei, and the median accessory nucleus. The DCN are organised by both somatotopy and modality, and have a diverse range of afferent inputs and projection targets. The functional organisation and connectivity of the DCN implicate them in a variety of sensorimotor functions, beyond their commonly accepted role in processing and transmitting somatosensory information to the thalamus, yet this is largely underappreciated in the literature. To consolidate insights into their sensorimotor functions, this review examines the morphology, organisation, and connectivity of the DCN and their associated nuclei. First, we briefly discuss the receptors, afferent fibres, and pathways involved in conveying tactile and proprioceptive information to the DCN. Next, we review the modality and somatotopic arrangements of the remaining constituents of the DCN-complex. Finally, we examine and discuss the functional implications of the myriad of DCN-complex projection targets throughout the diencephalon, midbrain, and hindbrain, in addition to their modulatory inputs from the cortex. The organisation and connectivity of the DCN-complex suggest that these nuclei should be considered a complex integration and distribution hub for sensorimotor information.

As new vaccines reduce P. falciparum (Pf) cases, clinicians can focus on rescuing more children with cerebral malaria (CM). Adjunctive “therapeutically-rational exchange transfusion” (T-REX) refers to using special “Pf-resistant” donor red blood cells (RBCs) that secrete nano-sized RBC extracellular vesicles (EVs). Can some RBC EVs rapidly dislodge Pf-infected RBCs (iRBCs) sequestered in blood vessels and reduce inflammation? Does post-exchange “rebound parasitemia” reflect sequestration-reversal? We reviewed case-reports, EV and liposome studies, expert perspectives, and time-sequence data. In the AQUAMAT study, median coma-recovery time was 20 hours for artesunate. In contrast, a CM patient treated with type-O T-REX quickly began speaking (during the procedure). For other rapid-recovery CM patients, donor RBC variables had not been specified. Despite rapid Pf-killing, drugs need 20 hours to substantially reduce iRBC cytoadhesion while EVs can selectively bind distant inflamed tissues within 15 minutes. RBCs stressed by blood-bank storage and Pf infection secrete EVs. Post-exchange “rebound parasitemia” can occur within 60 minutes and may reflect release of sequestered iRBCs. Sequestration-reversal can be assessed by monitoring Pf parasitemia and total Pf biomass. New data suggest clinicians, working with transfusion- and laboratory-medicine physicians, can, and should, assess T-REX options and publish their findings to help clarify how RBC EVs may serve as therapeutic “decoy ligands.”

As screen sizes are becoming larger and larger, which are beyond human’s physical limitation for direct touching interaction, remote controls are inevitable. However, as techniques applied so far, inertial gyroscopes are susceptible to position inaccuracies, and gesture recognition is limited by cameras’ focus depth and viewing angle. Grating antenna light trapping technology will be an ideal candidate providing the ghost point problem for multipoint inputs can be solved. Therefore, we propose a differential amplitude modulation scheme for grating antenna based multi beam optical touch, which can recognize different incidence points. Where, the amplitude of the incident beams was coded with different pulse width at first. Then, after been trapped by the grating antenna and been transferred into currents by the lined detector arrays, the incident points of the individual beams were recognized and differentiated. The scheme was successfully verified on an 18-inch screen, where two-point optical touch with position accuracy error under 3mm and response time less than 7ms under modulation frequency of 10kHz on both incident beams are obtained. This work paves a practical way for remote multi-point touch, which can make digital mouse in consistent to the users pointing direction obeying natural three-point one ling aiming rule instantaneously.

Smith-Magenis syndrome is a complex neurobehavioral genetic disorder. The spectrum of SMS phenotype is broad but commonly includes craniofacial, neurobehavioral, and otolaryngologic features. While the etiology of SMS is commonly attributed to one copy interstitial deletion in the 17p11.2 region (90-95% of cases), variants identified by sequence analysis in RAI1 have also been reported in 5-10% of cases. The phenotypic spectrum of patients with RAI1 sequence alterations is not clear. In this study, we report a 9-year-old male with global cognitive and psychomotor developmental delay, musculoskeletal and cardiovascular abnormalities, and dysmorphic craniofacial features. Whole genome quad analysis of the proband, unaffected parent, and unaffected brother identified a novel de novo RAI1:c.2736delC variant. This is the first report of this variant in the literature. This report also highlights the details of the genome analysis and this patient's phenotypic spectrum.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

We propose a deep-learning approach for the joint MIMO detection and channel decoding problem. Conventional MIMO receivers adopt a model-based approach for MIMO detection and channel decoding in linear or iterative manners. However, due to the complex MIMO signal model, the optimal solution to the joint MIMO detection and channel decoding problem (i.e., the maximum likelihood decoding of the transmitted codewords from the received MIMO signals) is computationally infeasible. As a practical measure, the current model-based MIMO receivers all use suboptimal MIMO decoding methods with affordable computational complexities. This work applies the latest advances in deep learning for the design of MIMO receivers. In particular, we leverage deep neural networks (DNN) with supervised training to solve the joint MIMO detection and channel decoding problem. We show that DNN can be trained to give much better decoding performance than conventional MIMO receivers do. Our simulations show that a DNN implementation consisting of seven hidden layers can outperform conventional model-based linear or iterative receivers. This performance improvement points to a new direction for future MIMO receiver design.

The article evaluates the use of machine learning methods to predict valve plate failures in hydraulic pumps. To conduct this assessment, a laboratory setup was developed that allowed the creation of a training dataset containing both the normal operating state of the pump and the operating state with three different valve plate damages. Five different predictive models were evaluated, including three composite models based on decision trees: Random Forest, Gradient-Boosted Trees, and Rotation Forest, as well as the kNN algorithm and a neural network. The analysis showed that neural networks achieved the highest prediction accuracy, enabling a prediction accuracy level of 89%. The kNN algorithm ranked second, and tree-based algorithms performed 4% worse than the neural network. Additionally, the attribute importance analysis revealed that leak flow, pressure output together with output flow, are the most important parameters for accurate prediction.

Temporomandibular disorders (TMD) affect a high percentage of children and adults worldwide. Surgery may be indicated in severe or recalcitrant case. Several recent advancements in the TMD and temporomanidbular joint (TMJ) surgery have elevated understanding and ability to treat affected patients. We discuss recent advances in TMD epidemiology, juvenile idiopathic arthritis (JIA) of the TMJ, and surgical techniques and technologies. Technical advancements have been identified in TMJ arthroscopy, treatment of TMJ subluxation and dislocation, and extended prosthetic total TMJ reconstruction (eTMJR). Overall, this review provides valuable insights into significant recent advancements of TMJ disorders and their surgical management.

The combination of encryption and digital watermarking technologies is a trend to achieve full lifecycle data protection. Recently, reversible data hiding in encrypted domain (RDHED) has greatly aroused the interests of many scholars. But the fixed order of first encryption and then watermarking makes this kind of algorithms unsuitable to many applications. Commutative encryption and watermarking (CEW) technology realizes the flexible combination of encryption and watermarking, and suits more applications. However, most existing CEW schemes for vector maps are not reversible and unsuitable to high precision maps. To solve this problem, here we propose a commutative encryption and reversible watermarking (CERW) algorithm for vector maps based on virtual coordinates which are uniformly distributed on the number axis. The CERW algorithm consists of virtual interval step based encryption scheme and coordinate difference based reversible watermarking scheme. In the encryption scheme, the map coordinates are moved randomly by multiples of virtual interval step defined as distance between two adjacent virtual coordinates. In the reversible watermarking scheme, difference expansion (DE) technique is used to embed the watermark bit into the coordinate difference computed based on the relative position of a map coordinate in a virtual interval. Since the relative position of a map coordinate in a virtual interval keeps unchanged during the coordinate scrambling encryption process, the watermarking operation and the encryption operation don’t interfere with each other and the commutativity between encryption and watermarking achieves. Results show that: proposed method has high security, high capacity and good invisibility. In addition, the algorithm is not only applicable to polyline and polygon vector data, but also can be applied to sparsely distributed point data which the traditional DE watermarking algorithm often fails to watermark.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

The dynamics of the topological charge of a vortex optical beam propagating in a turbulent air with accounting for the cubic nonlinearity is theoretically considered. On a number of examples, we show that the optical beam self-focusing manifests itself ambiguously depending on optical wave power. At near-critical values of beam power, self-focusing leads to enhanced spatial localization of optical vortices and substantial suppression of vortex walk-off relative to the beam axis caused by air turbulence. However, with increasing of optical intensity the modulation instability imposed by cubic nonlinearity becomes significant and contributes jointly with medium turbulence to faster divergence of vortex beams.

Lipid composition in the cellular membranes plays an important role in maintaining the struc-tural integrity of cells and in regulating cellular signaling that controls functions of both mem-brane-anchored and cytoplasmic proteins. ATP-dependent ABC and P4-ATPase lipid transport-ers, two integral membrane proteins, are known to contribute to lipid translocation across the li-pid bilayers on the cellular membranes. In this review, we will highlight current knowledge about the role of cholesterol and phospholipids of cellular membrane in regulating cell signaling and how lipid transporters participate this process.

Beam dumps are indispensable components for particle accelerator facilities to absorb or dispose beam kinetic energy in a safe way. However, the design of beam dumps based on conventional technology, i.e. the energy deposition via beam-dense matter interaction, makes the beam dump facility complicated and large in size, partly due to nowadays’ high beam intensities and energies achieved. In addition, these high-power beams generate radioactive hazards, which need specific methods to deal with. On the other hand, the EuPRAXIA project can advance the laser-plasma accelerator significantly by achieving 1-5 GeV high quality electron beam in a compact layout. Nevertheless, the beam dump based on conventional technique will still produce radiation hazards and make the overall footprint less compact. Here, we propose to implement a plasma beam dump to absorb the kinetic energy from the EuPRAXIA beam. In doing so, the overall compactness of the EuPRAXIA layout will not be impacted, and the radioactivity generated by the facility can be mitigated. In this paper, results from particle-in-cell (PIC) simulations are presented for plasma beam dumps based on EuPRAXIA beam parameters.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

The objective of this paper was to study the expression pattern of the GLOD4 gene in the testis and its regulatory effect on testicular cells. Currently, the regulated mechanism through are unclear. Here, we explored how GLOD4 functions in goat leydig cells to enhance our understanding of spermatogenesis and improve reproduction in breeding rams. In this study, we demonstrated that the localization of GLOD4 in testicular cells using immunohistochemistry and subcellular localization analyses. Subsequently, we analyzed the GLOD4 expression pattern in 4 age-based groups (0, 6, 12, and 18 months old) using real-time quantitative polymerase chain reaction (qRT‒PCR) and protein blotting. Finally, we performed GLOD4 gene silencing and overexpression studies in testicular cells from goats and explored the effects of GLOD4 on cell proliferation, the cell cycle, steroid hormone secretion and the expression of candidate testosterone hormone-regulated genes. GLOD4 was mainly expressed in testicular leydig cells, and the subcellular localization results showed that the GLOD4 protein was mainly localized in the cytoplasm and nucleus. Silencing of GLOD4 significantly suppressed the mRNA expression levels of the testosterone secretion-related genes CYP11A1, 3β-HSD and CYP17A1 and the mRNA expression levels of cell-cycle related genes CDK6, PCNA, and Cyclin E. Moreover, the cell cycle was blocked at the G2/M phase after GLOD4 silencing, which significantly suppressed testosterone secretion. In contrast, GLOD4 overexpression significantly increased the mRNA expression levels of the testosterone secretion-related genes CYP11A1, 3β-HSD, and CYP17A1 and increased the expression of the cell-cycle related genes CDK6, PCNA, and Cyclin E. Moreover, GLOD4 overexpression promoted the cell cycle from G0/G1 phases to enter the S phase and G2/M phases,promoted the secretion of testosterone. Taken together, our experimental results indicate that GLOD4 may affect the development of cells in Qianbei Ma goats of different ages by influencing the cell cycle, Proliferation and testosterone hormone synthesis. These findings enhance our understanding of the functions of GLOD4 in the cells of goats.

To investigate the bioactivities of fresh garlic and its processed product, black garlic, we conducted comparative analyses of antioxidant, anti-inflammatory, innate immune activation and anti-cancer activities, in addition to chemical composition (sugar, amino acid, polyphenol contents) of these materials. Simultaneous assay using neutrophil-like cells showed that fresh garlic exhibited antioxidant and innate immunostimulatory activities, whereas black garlic displayed a potent anti-inflammatory effect. The antioxidant activity index was correlated with phenol and flavonoid contents, while the innate immunostimulatory activity was correlated with fructan content. Furthermore, some black garlics with low fructose content were found to inhibit the proliferation of UM-UC-3 cancer cells, while other black garlics rich in fructose increased UM-UC-3 cell proliferation. It was shown that the thermal processing steps of fresh garlic could change the composition of sugars, antioxidants, and amino acids, which have different effects on neutrophil-like cells and UM-UC-3 cells, as well as on bioactivities.

In recent years, growing attention has been directed towards the potential of plant extracts as great therapeutic agents in controlling oxidative stress and inflammation. Gymnema inodorum (Lour.) Decne, an indigenous plant locally grown in Northern Thailand, is known for its anti-diabetic activity. This study aims to explore the antioxidant properties and phenolic profile of column chromatographic fractionated G. inodorum leaf extract. The ethanolic-reflux extracts of G. inodorum leaves were subjected to column chromatography for the isolation of bioactive molecules. Total phenolic and flavonoid content were assessed using Folin–Ciocalteu and aluminium chloride colorimetric methods, respectively. Total antioxidant activity was evaluated by employing different antioxidant assays, including 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulfonic)acid (ABTS) scavenging assay and ferric reducing antioxidant power (FRAP) assay. High-Performance Liquid Chromatography (HPLC) with a C18 column was employed to determine the level of gymnemic acid, while Liquid Chromatography Quadrupole Time-of-Flight/Mass Spectrometry (LC-QTOF/MS) was used to identify potential phenolic compounds. The three separated fractions indicating A, B, and C, exhibited remarkable antioxidant activity, with total phenolic content of 0.294 ± 0.056, 0.085 ± 0.039, and 0.227 ± 0.041 mg QE/mL, and total flavonoid content of 0.274 ± 0.050, 0.309 ± 0.110, and 0.384 ± 0.007 mg QE/mL, respectively. Fraction A exhibited the highest DPPH and ABTS scavenging activity, while fraction C demonstrated significantly higher ferric-reducing power. HPLC analysis revealed a highest concentration of gymnemic acid in fraction C (0.393 ± 0.003 mg/g) compared to fraction A (0.159 ± 0.003 mg/g) and fraction B (0.142 ± 0.000 mg/g). The LC-QTOF/MS phenolic screening showed seven potential phenolic compounds in fraction A, seven compounds in fraction B, and four compounds in Fraction C. A significant relationship is found between antioxidant potential and total phenolic content, suggesting that phenolic compounds are the major contributors to the antioxidant activity of G. inodorum.

Scene classification plays an important role in the intelligent processing of high-resolution satellite (HRS) remotely sensed image. In HRS image classification, multiple features, e.g. shape, color, and texture features, are employed to represent scenes from different perspectives. Accordingly, effective integration of multiple features always results in better performance compared to methods based on a single feature in the interpretation of HRS image. In this paper, we introduce a multi-task joint sparse and low-rank representation model to combine the strength of multiple features for HRS image interpretation. Specifically, a multi-task learning formulation is applied to simultaneously consider sparse and low-rank structure across multiple tasks. The proposed model is optimized as a non-smooth convex optimization problem using an accelerated proximal gradient method. Experiments on two public scene classification datasets demonstrate that the proposed method achieves remarkable performance and improves upon the state-of-art methods in respective applications.

Temporomandibular disorders (TMD) is a group of orofacial pain conditions which is the most common non-dental pain complaint in the maxillofacial region. Due to the complexity of the etiology and often cyclical nature of the disease, the diagnosis and management of TMD remain a challenge where consensus is still lacking in many aspects. While clinical examination is considered the most important process in the diagnosis of TMD, imaging may serve as a valuable adjunct in selected cases. Depending on the type of TMD, many treatment modalities have been proposed, ranging from conservative options to open surgical procedures. In this review, the authors discuss the present thinking in the etiology and classification of TMD, followed by the diagnostic approach and the current trend and controversies in management.

There are several well-described molecular mechanisms that influence cell growth and are relat-ed to the development of cancer. Chemokines constitute a fundamental element which are not only involved in local growth but also affect angiogenesis, tumor spread and metastatic disease. Among them, the C-X-C motif chemokine ligand 12 (CXCL12) and its specific receptor the chemo-kine C-X-C motif receptor 4 (CXCR4) have been widely studied. The overexpression in cell mem-branes of CXCR4 has been shown to be associated with the development of different kinds of his-tological malignancies, such as adenocarcinomas, epidermoid carcinomas, mesenchymal tumors or neuroendocrine neoplasms (NENs). The molecular synapsis between CXCL12 and CXCR4 leads to the interaction of G proteins and activation of different intracellular signaling pathways in both gastroenteropancreatic (GEP) and bronchopulmonary (BP) NENs conferring greater ca-pacity for locoregional aggressiveness, epithelial-mesenchymal transition (EMT) and the ap-pearance of metastases. Therefore, it has been hypothesized how to design tools that target this receptor. The aim of this review is to focus on current knowledge of the relationship between CXCR4 and NENs, with a special emphasis on diagnostic and therapeutic molecular targets.

Classifying spinal tumors can be challenging due to nonspecific clinical and radiological qualities, and a precise biopsy is crucial for an accurate diagnosis and treatment planning. This study aimed to enhance the accuracy and efficiency of spinal biopsies integrating Cone Beam Computed Tomography (CBCT) and magnetic resonance imaging (MRI) modalities using an O-arm CT navigation system. Eighteen patients with diverse spinal lesions underwent 18 biopsies following the Stealth Station navigation system Spine 8 protocol. Preoperative MRI scans were merged with intraoperative CT navigation systems for continuous monitoring during the biopsy process. The combined imaging technique accurately identified the diseased lesion type in all biopsies, demonstrating 100% sensitivity and specificity. In conclusion, combining MRI and CT imaging modalities significantly improved spinal biopsy accuracy and efficiency, differentiating between pathological entities. However, large-scale studies are desired to validate these findings and investigate potential benefits in different clinical scenarios. Although this method requires general anesthesia, its potential profits in avoiding misdiagnosed lesions and decreasing the need for further invasive procedures make it a promising approach for improving spinal biopsy accuracy and efficiency.

Liquid manipulation by photoisomerization attracts recent attentions as a new active droplet control method for micro-chemical analysis. Such a non-inverse manipulation can be realized by a use of solution liquid of surfactant that exhibits the \emph{cis}-\emph{trans} isomerization triggered by light irradiation with a specific wavelength such as ultraviolet light. Since the isomerization is accompanied by changes in fluid properties, a light irradiation on one of liquid-air interfaces of a liquid column in a tube would generate differences in the wettability accompanied between the both sides of the finite liquid column. Although this technique has been demonstrated experimentally by Muto et al. (\emph{Euro.~Phys.~J.~Special Topics}, {\bf 226}, 2016, 1199--1205), its dynamics and developments of each isomer distribution are not understood. In order to reveal the liquid-column migration phenomenon, we have performed numerical simulations of air-liquid two-phase flows and its scalar transport of the isomer, using the Volume-of-Fluid method in conjunction with the Continuum-Surface-Force model and Continuous-Species-Transfer method. We validated present results by comparison with experimental result in terms of the migration distance of the liquid column. We confirmed a termination of the liquid-column migration occurs when the \emph{cis} isomer distribution reaches the non-irradiated region. The migration speed was less dependent on the liquid-column length and was proportional to the tube diameter.

This paper focuses on a joint model to analyse longitudinal proportion and survival data. After transforming the longitudinal proportional data by a logit function, we adopt a partially linear mixed-effect model for it, in which nonlinear function of time is fitted via using B-splines technique and a centered Dirichlet Process Mixture Model (CDPMM) is specified for a general distribution of random effects. The survival data is assumed to a Cox proportional hazard model, the sharing random effects joint model is developed for the two types of data. Combining the Gibbs sampler and the Metropolis-Hastings algorithm, we propose a Bayesian Lasso (BLasso) method to simultaneously estimate unknown parameters and select important covariates. Simulation studies are conducted to investigate the finite sample performance of the proposed methods. An example from the MA.5 research experiment is used to illustrate the proposed methodologies.