Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

PURPOSE: To investigate the oxylipin profiles in aqueous humor of primary open angle glaucoma (POAG) patients. METHODS: Aqueous humor samples were collected from 17 POAG patients and 15 cataract subjects and subjected to the liquid chromatography-mass spectrometry (LC-MS) analysis to detect the oxylipins. The prediction potential of the differential abundant oxylipins was assessed by the receiver operating characteristic (ROC) curves. Pathway and correlation analyses on the oxylipins and clinical and biochemical parameters were also conducted. RESULTS: The LC-MS analysis detected a total of 76 oxylipins, of which 29 oxylipins reached the detection limit. The multivariate analysis identified 5 differential abundant oxylipins, 15-keto-prostaglandin F2 alpha (15-kPGF2α), Leukotriene B4 (LTB4), 12,13-Epoxyoctadecenoic acid (12,13-Epome), 15-Hydroxyeicosatetraenoic acid (15-HETE) and 11-Hydroxyeicosatetraenoic acid (11-HETE). The 5 oxylipins are enriched in the arachidonic acid metabolism and linoleic acid metabolism pathways. Pearson correlation analysis showed that 11-HETE was positively correlated with intraocular pressure and central corneal thickness and negatively with cup/disk ratio in the POAG patients. In addition, 15-kPGF2α was positively correlated with visual field defect, and LTB4 was negatively correlated with macular thickness.  CONCLUSIONS: This study revealed the oxylipin profile in the aqueous humor of POAG patients. Oxylipins involved in arachidonic acid metabolism pathway could play a role in POAG and anti-inflammatory therapies could be potential treatment strategies for POAG.

Soft pneumatic actuators/robotics have received significant interest in the medical and health fields, due to their intrinsic elasticity and simple control strategies enabling desired interaction. However, current soft hand pneumatic exoskeletons often exhibit uniform deformation, mismatch the profile of the interacted objects, and seldom quantify the assistive effects during activities of daily life (ADL), such as extension angle and joint stiffness predicted. The lack of quantification poses challenges to the effective and sustainable advancement of rehabilitation technology. This paper introduces the design, modeling, and testing of pneumatic bioinspired Segmented Composite Proprioceptive Bending Actuators (SCPBAs) for hand rehabilitation in ADL tasks. The actuator’s soft-joint/rigid-bone segmented structure, inspired by the human finger anatomy, provides a superior fit compared to traditional continuous structures. A quasi-static model is established to predict the bending angles based on geometrical parameters. The SCPBAs also include a quantitative evaluation of joint stiffness and extension angle utilizing proprioceptive bending information. Additionally, a soft under-actuated hand exoskeleton equipped with SCPBAs demonstrates its potential in ADL rehabilitation scenarios.

This paper explores the geometric impossibility of angle trisection within Euclidean geometry, with a particular focus on the 90° angle. It presents a rigorous proof that highlights the fundamental limitations of various approaches to angle trisection, highlighting their failure to achieve universality. The paper critiques modern proofs that allow for the trisection of certain angles while dismissing others, arguing that such methods are inherently flawed due to their lack of geometric consistency. The paper introduces a new perspective through a new property named “inconsistent property”, a concept derived from geometric operations involving proportional magnitudes. This property reveals contradictions within the framework of Euclidean geometry, paralleling the logical challenges faced in proving the impossibility of trisecting an arbitrary angle. By drawing comparisons between traditional and contemporary proofs, the paper demonstrates that inconsistencies arise not only from specific cases but also from broader geometric principles. The findings reaffirm the robustness of Euclidean geometry in addressing the trisection problem and challenge the validity of alternative proofs that do not adhere to universal geometric principles. This paper contributes to a clearer understanding of the limitations of angle trisection methods and encourages further investigation into the technical implications and broader impact of the angle impossibility proof.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Variable-Angle Tow (VAT) laminates can improve straight fiber composites mechanical properties thanks to the application of curvilinear fibers. This characteristic allows to achieve ambitious objectives for design and performance purposes. Nevertheless, the wider design space and the higher number of parameters result in a more complex structural problem. Among the various approaches that have been used for VATs study, Carrera’s Unified Formulation (CUF) allows to obtain multiple theories within the same framework, guaranteeing a good compromise between the results accuracy and the computational cost. In this article, the linear buckling behavior of VAT laminates is analyzed through the extension of CUF 2D plate models within the Reissner’s Mixed Variational Theorem (RMVT). Results show that RMVT can better approximate the prebuckling non-uniform stress field of the plate when compared to standard approaches, thus improving the prediction of the linear buckling loads of VAT composites.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Background: We compared corneal visualization Scheimpflug technology (CST) parameters between eyes with primary open-angle glaucoma (POAG) and primary angle-closure glaucoma (PACG). Methods: A retrospective analysis was done on data from 89 eyes with POAG and 83 eyes with PACG that had CST examinations. CST parameters were compared between eyes with POAG and those with PACG using a linear mixed model (LMM). Results: No differences were observed in age, central corneal thickness, intraocular pressure, or use of antiglaucoma eye drops between the two groups. Patients with PACG had a significantly shorter axial length (AL), a higher proportion of females, CST parameters, longer applanation 2 (A2) time, deeper A2 deformation amplitude, shorter peak distance (PD), longer whole eye movement, and longer whole eye movement time than patients with POAG. Highest concavity (HC) length and PD showed a significant positive correlation with AL. However, A1 length, A1 deformation amplitude, A2 time, A2 velocity, A2 length, A2 deformation amplitude, HC time, whole eye movement, and whole eye movement time were negatively correlated with AL. Conclusions: Biomechanical properties of the cornea differed between PACG and POAG. In some parts, AL differences between the POAG and PACG groups might contribute to the variation in CST parameters.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

We present a high-throughput nanoindentation study of in-situ bending effects on incipient plastic deformation behavior of polycrystalline and single-crystalline pure aluminum and pure copper at ultra-nano depths (<200nm). We find that hardness displays a statistically inverse dependence on in-plane stress for indentation depths smaller than 10nm, and the dependence disappears for larger indentation depths. In addition, plastic noise in the nanoindentation force and displacement displays statistically robust noise features, independently of applied stresses. Our experimental results suggest the existence of a regime in FCC crystals where ultra-nano hardness is sensitive to residual applied stresses, but plasticity pop-in noise is insensitive to it.

In the paper, the authors view some ordinary differential equations and their solutions from the angle of (the generalized) derivative polynomials and simplify some known identities for the Bernoulli numbers and polynomials, the Frobenius-Euler polynomials, the Euler numbers and polynomials, in terms of the Stirling numbers of the first and second kinds.

To have a better protection, strong toughness and good flexibility, all lives and plants must have skins, similarly, all books should have covers. In this paper, considering interlayer friction as a perturbation, we formulate a hardcover-book-like laminated plates with internal friction. For a quasi-static problem, detail analysis on the bending response and energy dissipation are carried out for a three-point-supported plates. Our numerical investigations show that the hardcover is more essential than the core layers in terms of bending response, and the energy dissipation within per loading-unloading cycle can be made to vary by a considerable amount. The central goal of studying is not only to predict the bending deformation of the book-like-plates, but also as a representative case to help finding some clue on the universal behaviours of multilayered architectures with internal friction.

Demolished concrete and plastic waste are two increasingly aggravating problems. In this study, a novel method was proposed to simultaneously recycle concrete and plastic wastes by compacting concrete and plastic powders together under pressure and temperature. The influence of compression pressure and temperature as well as the mixture proportion on the bending strength of specimens was investigated. The results showed that pressure and temperature had a positive effect on the specimen strength; however, the molding temperature should not exceed the melting temperature of plastic. The proportion of plastic had a minimal effect on the bending strength of the specimen when plastic accounted for 25%–75% of the overall mass of the test piece.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

This paper presents an exact solution to the Timoshenko beam theory (TBT) for first-order analysis, second-order analysis, and stability. The TBT covers cases associated with small deflections based on shear deformation considerations, whereas the Euler–Bernoulli beam theory (EBBT) neglects shear deformations. Thus, the Euler–Bernoulli beam is a special case of the Timoshenko beam. The moment-curvature relationship is one of the governing equations of the EBBT, and closed-form expressions of efforts and deformations are available in the literature. However, neither an equivalent to the moment-curvature relationship of EBBT nor closed-form expressions of efforts and deformations can be found in the TBT. In this paper, a moment-shear force-curvature relationship, the equivalent in TBT of the moment-curvature relationship of EBBT, was presented. Based on this relationship, first-order and second-order analyses were conducted, and closed-form expressions of efforts and deformations were derived for various load cases. Furthermore, beam stability was analyzed and buckling loads were calculated. Finally, first-order and second-order element stiffness matrices were determined.

The object of study is a transversely bent triangular plate made of orthotropic material fixed along the edges of the plate under the action of a uniformly distributed load. Fourth-order differential equilibrium equations with variable orthotropy parameters were used. The equations were approximated by finite differences for a grid of scalene triangles. This type of mesh accurately describes the boundary contour of the triangular-shaped plates. The boundary conditions for the mesh consider the orthotropy of the plate material. Seven standard finite-difference equations have been developed considering the boundary conditions along the three edges of the plate and the presence of three angles of an irregularly shaped triangle. A finite difference matrix is obtained. The matrix structure makes calculating a triangular plate at different base angles possible. The boundary conditions were varied in the form of rigid or hinged support of triangular plates. The calculation method considers the orthotropic parameters of the material in two mutually perpendicular planes. The adaptation of the numerical method to the calculation of orthotropic plates of arbitrary shape is described. Relationships are given for determining the rigidity characteristics of orthotropic materials. An algorithm for simple engineering calculation of triangular orthotropic plates is proposed, which makes it possible to perform accurate calculations in variant design.

We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

Continuum robots play the role of end-effector in various surgical robots and endoscopic devices. The robots may be categorized as rigid or soft continuum robots (SCRs). While the SCRs have proven advantages such as safety and compliance, more research and development are required to enhance their capability for specific medical scenarios. This research aims at designing a soft robot considering concepts of geometric and kinematic similarities. The chosen application is a semi-invasive medical application known as Transesophageal Echocardiography (TEE), but the methodology can be implemented in other similar applications. Since established rigid carrier construction make use of principles we find as well embodied in vertebral spines, the paragon for soft robot solution can be the phylogenetic precursor of the spine, the Chorda dorsalis. The feasibility of fabrication of a soft endoscopic device derived from that paragon within a robotics laboratory was shown empirically by producing a three-segment pneumatic SCR. The kinematic model was proposed based on the method of transformation matrices, and an algorithm based on a self-organizing map (SOM) was proposed and applied to realize kinematic similarity. The simulation results indicate that the algorithm acting as an open-loop controller forces the soft robot tip to follow the desired path which in this case is the path of the rigid probe. It is concluded that the solution provides a soft robot that can surrogate and succeed the traditional rigid counterpart owing to size, workspace, and kinematics.

In light of the current situation where no testing equipment is available for measuring thermal deformation of objects, this paper proposes a novel method for accurate and precise measurement. The method overcomes the limitations of previous approaches that relied on pitch angle. By utilizing the principle of biplane multiple reflections, a bivariate laser spot displacement analysis algorithm is devised to attain highly precise measurements of bivariate angles. Additionally, a temperature gradient comparison algorithm is introduced to calculate the indicator test results under specific temperature conditions. To validate the effectiveness and reliability of this method, a testing system is constructed and utilized. The results demonstrate that the thermal deformation angle change test achieves an impressive accuracy of 0.015″ and a rate of thermal deformation angle change of 0.3247″/°C. These values are in close agreement with the previously simulated analysis result of 0.359″/°C, with only a relative error of 9.55%. Therefore, the test results confirm the efficacy and reliability of this testing method along with the feasibility of the algorithm processing.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

It is well known that the photon trajectories follow a curved path in a gravitational field. We explore here the gravitational bending of electric field lines. It seems that the electric field lines of a charge, supported in a gravitational field, follow exactly the trajectories of photons emitted isotropically from a source situated at the charge location. From a detailed examination of the electrostatic field of a charge accelerated uniformly in the instantaneous rest frame, exploiting the strong principle of equivalence, one can determine the bending of the electric field lines of a charge in a gravitational field. The fraction of electric field lines crossing a surface, stationary above or below the charge in the gravitational field, is shown to be exactly similar to the fraction of photon trajectories, emitted from a source placed at the charge location, intersecting that surface. On the other hand, for a freely falling charge in the gravitational field there is no such bending of electric field lines. The field lines continue to extend in radial straight lines from the instantaneous 'present' position of the charge, as do the trajectories of photons streaming away from the instantaneous position of a freely falling source in the gravitational field. The electric field configuration of a freely falling charge in the gravitational field is shown to be exactly the same as that of a charge moving uniformly in an inertial frame with velocity equal to the instantaneous ``present'' velocity of the freely falling charge.

The Cobb angle is critical in assessing adolescent idiopathic scoliosis (AIS) patients. This study aimed to evaluate the error in selecting the cranial and caudal limit vertebrae on AIS digital X-rays of experienced and novice observers and its correlation with the error in measuring the Cobb angle and determining the length of the scoliotic curves. Using the TraumaMeter v.873 software, eight raters (four experienced and four novices) independently evaluated 68 scoliotic curves on 42 AIS X-rays across three sessions one month apart according to Hopkins’ criteria of absolute reliability. Two spine specialist experts using the Cobb method established the gold standard measurements. The percentage of error in the selection of the cranial vertebrae (the most-tilted vertebra above the apex) is higher than in the caudal vertebrae (the most-tilted vertebrae below the apex) (44.7%, CI95% 41.05-48.3 compared to 35%, CI95% 29.7-40.4). The error in the choice of the most tilted vertebrae, in number of vertebrae per scoliotic curve, was MBE (mean bias error) =0.45, CI95% 0.38-0.52 in the cranial and MBE=0.35, CI% 0.69-0.91 in the caudal. The percentage of errors in the choice of boundary vertebrae is lower for the experienced than for the novices, both in cranial and caudal. The experienced chose at least one boundary vertebrae incorrectly in 52% of the meas-urements and the novices in 65.1%. The error in the Cobb angle did not depend on the number of boundary vertebrae chosen incorrectly (r=0.198, p=0.111). Of the 50% of Cobb angle measurements closest to the actual value, 55.4% (454) were obtained by incorrectly selecting at least one boundary vertebra. There was a positive correlation (r=0.673, p=0.000) between the error in selecting the boundary vertebrae and the error in determining the length of the scoliotic curves. The error in quantifying the length of scoliotic curves was MBE=0.43, CI95% 0.35-0.51 vertebrae per curve. We can conclude that errors in selecting boundary vertebrae are common among experienced and novice observers, with a greater frequency of error in the cranial vertebrae. There is no correlation between the error in selecting the boundary vertebrae and the error in measuring the Cobb angle. Contrary to the consensus, the accuracy of determining the length of the scoliotic curve is limited by the Cobb method’s reliance on the correct selection of boundary vertebrae. Inappropriate choice of boundary vertebrae leads to an estimated error in determining the length of the scoliotic curves of 0.805 vertebrae for each boundary vertebra chosen incorrectly.

Corrugated boards are used for packaging because of their high strength-to-weight ratio, recyclability, and biodegradability. They have an orthotropic sandwich structure with unique characteristics for each direction owing to their flute shape. In this study, the bending behavior was qualitatively analyzed for various variables through an FE-based simulation, and the possibility of an alternative test method for the four-point bending test on a corrugated board was examined through a similarity analysis with the experimental results. The cross-machine direction (CD) bending stiffness through finite element analysis (FEA) simulation was closely related to the thickness of the corrugated board. In AB-flute-double-wall (AB/F-DW), the difference in CD bending stiffness based on the bending direction was approximately 17.2% in the FEA simulation and approximately 10.5% in the experiment. However, the differences in the bending behavior (bending force vs. deflection plot) and bending stiffness based on the phase shift between the two flutes constituting BB-flute-double-wall (BB/F-DW) were insignificant. Overall, the CD bending behavior of the corrugated board was simulated relatively well through FEA simulation. However, it was impossible to simulate the machine-direction (MD) bending behavior through FE-based simulation because of a decrease in convergence and a large error caused by the variability of the contact condition of the modeled test specimen with a non-uniform MD cross-section.

Bending pipe is a common component of long distance pipeline. Accurately understanding the flow law of hydrate particles in elbow pipe is of great significance for optimizing pipeline design, improving production efficiency of gas transmission pipeline and ensuring pipeline safety. Taking the flow of hydrate particles in a Bending pipe as the object of study, the spiral flow attenuation and hydrate particle deposition under different bending pipe angles, different rate of bending pipe to diameter, different Reynolds number and different torsion were studied by numerical simulation method. The results show that the larger the swirl number, the higher the spiral flow intensity. When the fluid enters the bending pipe, the Angle of the bending pipe is larger, the torsional rate is smaller, and the Reynolds number is larger, the swirl number is larger, the intensity of the swirl flow is stronger, and the swirl number is larger at the same position. However, the larger the bending pipe to diameter ratio, the greater the change of the total swirl number and the weaker the strength at outflow, but the slower the change of swirl number, indicating that the spiral flow attenuation is slower. The larger the bending pipe Angle, the larger the bending pipe diameter rate, the smaller the torsion rate and the larger the Reynolds number, the smaller the deposition rate of the particles after flowing through the pipe. The results show that the spiral flow strength can be maintained in a proper way to reduce the deposition and ensure the safety of the conveying process.

Sarcopenia becomes more common with age, being most prevalent among elderly individuals. According to the EWGSOP, muscle mass is one of the criteria for the evaluation of sarcopenia. The main methods for evaluating muscle mass are CT, MRI, and DXA, but these methods are difficult to apply in the field due to equipment costs, radioactivity, and lack of portability. BIVA and PhA are alternative approaches for assessing somatic cell mass and volume and do not require predictive equations. These variables are clinically relevant parameters that indicate cell health, especially cell membrane integrity and cell function. This study in sarcopenic and nonsarcopenic elderly volunteers aimed to determine the BIVA distribution pattern among individual sarcopenia patients; to evaluate the relationship between PhA and muscle strength, muscle quality, and physical function; and to find any correlates of PhA. The sample comprised 134 free-living elderly individuals of both sexes aged 69–91 years. Anthropometric parameters, grip strength, DXA findings, BIA results, and physical performance (the 6-meter walk test) were measured. Impedance vector distributions were evaluated in sarcopenia patients and healthy elderly individuals using BIVA. According to the AWGS criteria, sarcopenia was diagnosed according to DXA findings, grip strength and physical performance test results. Group differences were evaluated using the t test, Mann‒Whitney U test, and Hotelling's T2 test. Correlation analysis was performed to identify variables significantly associated with PhA. Linear regression analysis was performed to determine whether PhA was associated with muscle strength, muscle quality and physical function. BIVA detected a significant difference between the sarcopenia and non-sarcopenia groups (both sexes) due to higher R/H values and lower phase angles in a few individuals, whereas Xc/Ht values did not differ between the two groups. The sarcopenia group had a significantly lower PhA than the non-sarcopenia group among both males (p&lt;0.01) and females (p&lt;0.05). PhA was significantly correlated with age, ASM, HGS, and muscle quality in both sexes and significantly correlated with ASM/Ht2 and physical performance in males. PhA was a significant indicator of muscle strength in both males (β = 2.6; p&lt;0.01) and females (β = 3.4; p&lt;0.01), a significant indicator of muscle quality in both males (β = 0.07; p&lt;0.05) and females (β = 0.17; p&lt;0.01), and a significant indicator of physical performance in males (β = 0.3; p&lt;0.01). BIVA can detect changes in muscle mass in individuals with sarcopenia and is a practical method for the assessment of sarcopenia in the field. PhA is a good indicator of muscle strength, muscle quality and physical performance (in males). These methods can help diagnose sarcopenia in elderly individuals with reduced mobility.

We explore the deflection angle in the framework of improved Schwarzschild Black hole utilizing the most advance geometrical path adopted by Gibbon-Werner. To investigate deflection angle of the photon ray by weak gravitational lensing for this black hole, we derive the optical curvature and perform the application of Gauss-Bonnet theorem on the optical metric. Moreover, we study the impacts of the plasma medium in context of the weak gravitational lensing in relate to this black hole. Further, we also study the graphical analysis of the deflection angle in both the plasma and non-plasma mediums. Also, we find the rigorous bound base upon the greybody factor for improved Schwarzschild black hole. A while later, we contrast our conclusions about deflection angle with the deflection angles of Schwarzschild black hole within plasma and non-plasma mediums.

In this article, we calculate the deflection angle of tidal charged black hole (TCBH) in weak field limits. First we obtain the Gaussian optical curvature and then apply the Gauss-Bonnet theorem on it. With the help of Gibbons-Werner method, we are able to calculate the light's deflection angle by TCBH in weak field limits. After calculating the deflection angle of light, we check the graphical behavior of TCBH. Moreover, we further find the light's deflection angle in the presence of plasma medium and also check the graphical behavior in the presence of plasma medium. Moreover, we investigate the shadow of TCBH.For calculating the shadow, we first find the null geodesics around the TCBH and then find its shadow radius. We also obtain TCBH's shadow in the plasma medium. Hence, we discuss the shadow of the TCBH using the $M87^{*}$ parameters announced by the Event Horizon Telescope.

Stress relaxation tests in cantilever bending were performed on the C7025 and C7035 alloys at 298K and 393K，respectively. The effect of stress-relief treatments on stress relaxation properties was investigated. The structural changes associated with the stress relaxation process were examined using transmission electron microscope. The stress relaxation curve fits well to empirical formula σ*=[Kˊln(t+α₀)+C]^-n for stress relaxation. The curves can be split into two stages. The stress relax quickly in the first stage, slows down in the second stage, and tends to be a certain limit value after a long time. The curve and microstructure reveals that the C7035 alloy has a lower rate of stress relaxation and a higher anti-stress relaxation capacity than the C7025. The first reason is that the movement of vacancies required by spinodal decomposition is inhibited, and the quantity of cobalt -containing vacancies decreases dramatically in the C7035 alloy. The other reason is that the precipitated phases became uniformly diffused in the C7035 alloy. The precipitate phase uniformly distributes in the grain boundaries and the matrix, during the relaxed condition, and thus the dislocations moving is blocked by the precipitates.

It is well known that X-ray crystallography is based on X-ray diffraction (XRD) by atoms and molecules. The diffraction pattern arises as a result of scattering of incident radiation, which makes it possible to determine the structure of the scattering substance. With the advent of ultrashort radiation sources, the theory and interpretation of X-ray diffraction analysis remained the same. This work shows that when an attosecond laser pulse is scattered on a DNA molecule, including during its nicking and bending, the pulse duration is an important characteristic of the scattering. In this case, the diffraction pattern changes significantly compared to the previously known scattering theory. The results obtained must be used in XRD theory to study DNA structures, their mutations and damage, since the previously known theory can produce large errors and, therefore, the DNA structure can be “deciphered” incorrectly.

Increasing traffic loads and changes in code provisions lead to deficits in shear and flexural capacity of many existing highway bridges. Therefore, a lot of structures in Europe and North America are expected to require refurbishment and strengthening in the future. This projection is based on the current condition of many older road bridges. Different strengthening methods for bridges exist to extent their service life, all having specific advantages and disadvantages. By applying a thin layer of carbon textile reinforced mortar (CTRM) to bridge deck slabs and the webs of prestressed concrete bridges, the fatigue and ultimate strength of these members can be increased significantly. The CTRM-layer is a combination of a corrosion resistant carbon fibre reinforced polymer (CFRP) fabric and an efficient mortar. In this paper, the strengthening method and the experimental results obtained at RWTH Aachen University are presented.

Rebar quantity estimation is pivotal for determining the cost of construction projects and essential for bidding purposes. A bar bending schedule plays a crucial role by providing rebar information and bending instructions, facilitating efficient procurement. Traditional methods of bar bending schedules, which involve manual extraction from 2D (two-dimensional) drawings, are error-prone and hinder construction productivity. This study proposes a Building Information Modeling (BIM)-based algorithm that automates the generation of a Bar Bending Schedule (BBS) directly from the 3D (three-dimensional) BIM models, ensuring accuracy and eliminating manual errors. The effectiveness of the algorithm was verified by comparing the rebar quantities generated by the model against those derived from optimization calculations. The results demonstrated a mean absolute error of 0.017 and a mean absolute percentage error of 1.13%, validating the algorithm’s precision. Additionally, it achieved a remarkable 33.33% reduction in the manpower required for preparing BBSs, highlighting its potential to revolutionize construction workflow efficiency and accuracy.

Many ethical issues arise when robots are introduced into elder-care settings. When ethically charged situations occur, robots ought to be able to handle them appropriately. Some experimental approaches use (top-down) moral generalist approaches, like Deontology and Utilitarianism, to implement ethical decision-making. Others have advocated the use of bottom-up approaches, such as learning algorithms, to learn ethical patterns from human behaviour. Both approaches have their shortcomings when it comes to real-world implementations. Human beings have been observed to use a hybrid form of ethical reasoning called Pro-Social Rule Bending, where top-down rules and constraints broadly apply, but in particular situations, certain rules are temporarily bent. This paper reports on implementing such a hybrid ethical reasoning approach in elder-care robots. We show through simulation studies that it leads to better upholding of human values such as autonomy, whilst not sacrificing beneficence.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

Primocane-fruiting (PF) blackberries are adaptable to different production systems. To increase yields in PF blackberries, their primocanes are typically tipped or topped in summer to encourage branch formation from axillary buds below the cut. In this study, we determined in PF ‘Prime-Ark Traveler’ whether early emerging primocanes were more productive than those that emerged later in the season and the effect of primocane bending and defoliation on flowering. The primocanes that emerged in April produced 64% more flower shoots than those that emerged after May. Also, these findings indicate the alternative primocane management practices of selecting the early emerging primocanes and bending to orient primocanes horizontally and leaf removal increase budbreak and flower shoot emergence. The present work contributes toward a better understanding of primocane emergence time and orientation-flowering relations and how they mediate crop performance in PF blackberry.

In this paper, we examine the weak deflection angle and greybody factor of magnetized regular black hole. We implement the Gauss-Bonnet theorem on magnetized regular black hole to get the deflection angle. Moreover, we analyze the influence of plasma and non-plasma mediums on deflection angle of magnetized regular black hole. We observe the graphical behaviour of plasma and non-plasma mediums on deflection angle of magnetized regular black hole. Lastly, we study the rigorous bound phenomenon of the greybody factor of magnetized regular black hole. For this purpose we calculate greybody factor results and analyze the graphical behaviour of greybody bound for the different values of the parameters.

Purpose: To investigate the extent of anterior chamber angle circumference needed to maintain a physiological outflow facility (C). Methods: Twenty anterior segments of porcine eyes were assigned to 5 groups, each with a different degree of cyanoacrylate-mediated angle closure: 90° (n = 4), 180° (n = 4), 270° (n = 4), 360° (n = 4) and four unoccluded control eyes. The outflow facility was measured at baseline, 3, 12, 24, and 36 hours after angle closure. Outflow patterns were evaluated with canalograms and the histomorphology was compared. Results: Baseline outflow facilities of the five groups were similar (F = 0.922, P = 0.477). Complete, circumferential occlusion over 360° induced a significant decrease in facility from baseline at all time-points (P ≤ 0.023 at 3, 12, 24 and 36 hours). However, no difference from baseline was found in any of the partially-occluded (0–270°) groups (F ≥ 0.067, P ≥ 0.296 at 3, 12, 24 and 36 hours). The canalograms confirmed the extent of occlusion with flow through the unblocked regions. Histology revealed no adverse effects of blockage on the TM or aqueous plexus in the unoccluded angle portions. The unoccluded TM appeared normal. Conclusion: Cyanoacrylate-mediated angle occlusion created a reproducible angle closure model. 90° of unoccluded anterior chamber angle circumference was sufficient to maintain physiological outflow. This model may help understand how outflow can be regulated in healthy, nonglaucomatous TM.

Hypotrochoidal profile contours have been produced in industrial applications in recent years using twin-spindle processes, and they are considered effective high-quality solutions for positive shaft–hub connections. This study mainly concerns analytical approaches to determine the bending stresses in hypotrochoidal profile shafts. The formulation was developed according to bending principles using the mathematical theory of elasticity and conformal mappings. The loading was further used to investigate the rotating bending behaviour. The stress factors for the classical calculation of maximum bending stresses were also determined for all those profiles presented and compiled in the German standard DIN3689-1 for practical applications. The results were also compared with the corresponding numerical and experimental results, and very good agreement was observed. Additionally, based on previous work, the stress factor was determined for the case of torsional loading to calculate the maximum torsional stresses in the standardised profiles, and the results are listed in a table. This study contributes to the further refinement of the current DIN3689 standard.

This research aims to investigate the carbon fiber reinforced polymer (CFRP) when subjected to tensile, bending, and compression. Half of the specimens are also subjected to water to find out how water influences. The CFRP is created using a combination of carbon fiber layers and epoxy resin Bisphenol A Epichlorohydrin with hardener and is formed using the vacuum infusion method. From the water absorption test, it was found that the average weight gain of the specimens was 2.9% and the lowest value was at 0.6%, it was concluded that the increase in wet specimen weight was not too significant and water absorption tended to be slow. Mechanical testing ob-tained the highest average tensile stress, bending stress, compressive stress, and modulus of elasticity of 195 MPa, 295 MPa, 96 MPa, and 8914 MPa were from dry specimens while the lowest average values were 146 MPa, 286 MPa, 81 MPa, and 6160 MPa from wet specimens. The results of micro-photo observations on the tensile test fracture show that the specimen has a XGM fracture character with delamination and splitting fractures happening in multiple areas. In the bending test, the specimens experienced buckling fracture due to the fiber breaking and the inability of the matrix to withstand the additional stress. Shear fracture happened during the compressive test. In conclusion, water absorption has a bad impact towards the composite strength.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries have been tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance have been determined. Results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with previous studies results, to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

Protein molecules show varying degrees of flexibility throughout their three-dimensional structures. This flexibility is associated with the fluctuation of the torsion angle in proteins. The protein backbone can be defined mainly by two torsion angles, phi (φ) and psi (ψ). The fluctuation of torsion angles is derived from different NMR models’ variations in backbone torsion angles. The angle fluctuations in the cartesian coordinate space are used to characterize the protein’s structural flexibility. Fluctuation of torsion angle is useful in predicting protein function and structure when the torsion angles are used as restraints. This study aims to develop a machine learning method to predict torsion angle fluctuations directly from protein sequences. It explores various useful features such as disorder probability, position-specific scoring matrix profiles, secondary structure probabilities, monograms, bigram, position-specific estimated energy, half-sphere exposures, etc. Likewise, it explores well-known machine learning methods and proposes an optimized Light Gradient Boosting Machine Regressor (LightGBM) method, named TAFPred, to predict torsion angle fluctuations with the selected features. The proposed method achieves ten-fold cross-validated correlation coefficients of 0.746 and 0.737 and mean absolute errors of 0.114 and 0.123 for the angle fluctuation of φ and ψ, respectively, and attains an improvement of 10.08% in MAE, 24.83% in PCC in the phi angle, and 9.93% in MAE, 22.37% in PCC in psi angle compared to the state-of-the-art method proposed by Zhang et al.

Carbon fiber reinforced polymers (CFRP) are extensively employed in the aerospace industry due to their excellent properties. Delamination damage occurring at critical locations in CFRP can seriously reduce the safety of in-service components. The detection and localization of delamination damage using Lamb waves hold significant potential for widespread application in non-destructive testing. However, the choice of damage localization algorithm may produce different delamination damage localization results. This research presented an IRAPID (improved reconstruction algorithm for probabilistic inspection of defects) method derived from the ORAPID (original reconstruction algorithm for probabilistic inspection of defects) method, aiming to improve the accuracy and reliability of delamination damage localization. Three CFRP bending plates, including a healthy bending plate and two bending plates with delamination damage sizes of Φ20 mm and Φ40 mm, were prepared in the experiment, respectively. The detection experiment of the CFRP bending plate using lead zirconate titanate (PZT) as a transducer to excite and receive Lamb waves was conducted, and the influence of excitation signal frequency on the performance of the proposed method was discussed. Under the condition of excitation signal frequency of 220 ~ 320 kHz and step size of 10 kHz, the accuracy of the delamination damage localization method proposed in this paper was compared with that of the existing methods. The experimental results indicate that the IRAPID algorithm exhibits good stability in the localization of delamination damage across the frequency variations range considered. The localization error of the IRAPID algorithm for delamination damage is significantly lower than that of the DaS (delay-and-sum) algorithm and the ORAPID algorithm. As the size of the delamination damage increases, so does the localization error. The accuracy of delamination damage localization is lower in the X-axis direction than in the Y-axis direction. By averaging the localization results across various frequencies, we can mitigate the potential localization errors associated with single-frequency detection to a certain extent. For the localization of delamination damage, Lamb waves at multiple frequencies can be employed for detection, and the detection results at each frequency are averaged to enhance the reliability of localization.

In this paper, thin plate theory and moderately thick plate theory are proposed for analyzing the bending problem of rectangular plates with stepped thickness resting on elastic half-space foundation. The ground reaction is considered as an unknown coefficient and the hypothesis of Winkler foundation model and two-parameter ground model is eliminated in this method, so as to obtain the law of internal force distribution of the plate and the distribution law of contact reaction force between the stepped rectangular plate and foundation. The stepped rectangular plate is divided into upper and lower plates, and thin plate theory and moderately thick plate theory are used to obtain the analytical solution. The obtained analytical solutions in this paper are compared with results reported in other publications to verify the accuracy of this method. The effects of the elastic modulus and dimensions of the plate, and theory of plate are also considered. The analytical solutions show that it is feasible to decompose the stepped rectangular plate into two plates for analyzing the bending properties of stepped rectangular plate, and this method provide a reference for the study of multilayer stepped rectangular plates.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

Single-layer core corrugated sandwich panels generally consist of a corrugated core and two layers of panels, while multi-layer core corrugated sandwich panels are formed by stacking multiple layers of panels with multiple layers of core layers. In this study, integrated multilayer core corrugated sandwich panels with different shapes of corrugated cores (triangular, trapezoidal, and rectangular) and the different number of core layers were fabricated using 3D printing technology, and the mechanical behavior of such multilayer core corrugated sandwich panels under quasi-static three-point bending was investigated using experiments and numerical simulations. The effects of core shape and number of core layers on the bending deformation process, damage mode, load carrying capacity, and bending energy dissipation capacity of multilayer core sandwich panels are discussed. Parametric design of multilayer triangular core corrugated sandwich panels was also carried out by finite element software ABAQUS. It was found that a new multilayer corrugated sandwich panel with a multi-layer core is better than the single core shape multilayer corrugated sandwich panel in terms of bending load capacity, energy dissipation capacity and deformation capacity can be obtained through the combination design of different core shapes.

Despite their limited spatial extent, freshwater ecosystems host remarkable biodiversity, including one third of all vertebrate species. This biodiversity is declining dramatically: globally, wetlands are vanishing three times faster than forests and freshwater vertebrate populations have fallen more than twice as steeply as terrestrial or marine populations. Threats to freshwater biodiversity are well- documented but co-ordinated action to reverse this decline is lacking. We present an Emergency Recovery Plan to “bend the curve” of freshwater biodiversity loss. Priorities for action include: 1) accelerating implementation of environmental flows, 2) improving water quality, 3) protecting and restoring critical habitats, 4) managing exploitation of freshwater species and riverine aggregates, 5) preventing and controlling non-native species invasions, and 6) safeguarding and restoring river connectivity. We recommend revised targets and indicators for the Convention on Biological Diversity and the Sustainable Development Goals, and investment in enabling conditions at national, river basin and local scales.

This paper presents an analytical method for determining the bending stresses and deformations in prismatic noncircular profile shafts with trochoidal cross sections. The so-called higher trochoids can be used as form-fit shaft–hub connections. Hybrid (mixed) higher trochoids (M-profiles) were proposed in [1] and adapted to a practical industrial application in [2]. M-profiles combine the advantages of standardised polygon (DIN 32711 [3]) and spline (DIN 5486 [4]) contours used as shaft–hub connections for the transmission of torsional loads. In this study, the geometric and mechanical properties of the higher hybrid trochoids were investigated using complex functions to simplify the calculations. The pure bending stress and shaft deflection were determined for M-profiles using the bending theory formulated by Muskhelishvili [5]. The loading cases consisted of static and rotating bends. Analytical, numerical, and experimental results agreed well.

Partially stabilized zirconia (PSZ) is a promising material with superior combination properties in a wide range of industries. In this study, the effect of grain size on the mechanical properties such as hardness, bending strength and fracture toughness (named as ‘indentation toughness’ in this study) was investigated. The multi-doped zirconia ceramics were prepared by powder processing and pressure-less sintered following four sintering schedules. The measured mechanical properties results show that the polymorph structure sintered at a higher temperature has a lower bending strength and hardness. But 300% more indentation toughness (30.54 Kg/mm) of samples sintered at 1600 °C +1150 °C relative to others was estimated due to the grain size effect by our suggested equation. By contrast, the fracture toughness was calculated with an existing method. The results showed that similar trends were obtained. It appeared to be a novel method for evaluating the toughness of partially stabilized zirconia ceramics with micron grains based on the size effect.

Hybrid fiber reinforced composites can be controlled by price, weight and various mechanical properties depending on fiber ratio and lamination method. Despite these excellent hybrid properties, there is a disadvantage that inter-laminar fracture due to external impact, which is the biggest weakness of fiber reinforced composite materials, is weak. The test specimens were prepared by using a vacuum bag method, which is manufactured by using an autoclave device. The pre-preg is manufactured in the form of a B-stage. In the process of fabricating the nanoparticle pre-preg, the homogeneizer using an ultrasonic wave was used to disperse the epoxy subject without the curing agent into nanoparticles. The dispersion of the nanoparticles was dispersed by the weight of the epoxy resin. This is to take into account the cohesion of HNT and to understand the range of cohesion of HNT in a matrix with viscosity and its phenomenon. According to the Comparison of the interlayer interfacial properties and mechanical properties of Aramid / Basalt fiber hybrid composites by HNT addition, the fracture toughness, ILSS and bending strength of specimens with HNT content of more than a certain level were decreased because of the aggregation of HNT.

On the basis of the golden ratio and the compasseses, every angle was divided into three equal parts. In general, it has been proven that the problem of triangulation of an angle cannot be solved on the basis of the golden ratio and the expanding of the angle. The relationship of golden relativity with Pi number and Euler's number has not been investigated to solve impossible problems. According to the investigation of events in six-dimensional space-time, with the simultaneous movement of two arms of the compasses based on the golden ratio, every angle was divided into three equal parts. The growth rate based on the golden ratio is the key to solving the most intractable mathematical and physical problems.

This paper is devoted to study the gravitational lensing for Curvature-coupled antisymmetric wormhole solution to compute the bending angle of light by utilizing the Gibbons and Werner technique. To achieve this, we find the Gaussian optical curvature and then apply Gauss-Bonnet theorem in the weak field limits. We also study the effects of plasma as well as dark matter mediums on the bending angle. Moreover, we analyze the graphical behaviour of the deflection angle $\alpha$ with respect to the impact parameter $\sigma$ and minimal radius $r_{0}$ in non-plasma and plasma mediums. We examine that deflection angle shows direct relation with $r_{0}$ such that large values of $r_{0}$ gives large deflection angle and small values of $r_{0}$ gives small deflection angle. For impact parameter $\sigma$, deflection angle $\alpha$ shows inverse relation. Additionally, we derive the deflection angle of light by using Keeton and Petters method and compare with the previous results.

Our earlier work has tentatively shown that the hierarchy of fermion masses and mixing angles follows from the universal behavior of nonlinear dynamics. In this brief sequel we survey a similar scenario in which the Cabibbo angle arises from the nonlinear dynamics of charged-current interactions.

Background A body composition monitor (BCM) has a role not only in determining over-hydration (OH) but also as an aid to nutritional assessment. For dialysis patient-specific clinical applications of BCM, it is necessary to clarify the relationship between body composition parameters and OH in healthy Chinese individuals. Methods This cross-sectional study involved 314 healthy individuals with a mean age of 45.7±13.1 years. BCM measurements were performed while the subjects were fasting. Results The mean OH level was 0.379±0.81 L. Lean tissue index (LTI) and Lean tissue mass (LTM) were significantly higher in males (p<0.001), while fat tissue index (FTI) was significantly higher in females (p<0.001). In univariate correlation analysis, FTI, Fat, and ATM had a negative correlation with OH in females and all subjects (p<0.05), while LTM and BCM had a positive correlation in all subjects (p<0.05). There was a significant negative correlation between phase angle (PhA) and OH in males, females, and all subjects (r=-0.634, p<0.001; r=-0.666, p<0.001; r=-0.484, p<0.001, respectively). In multivariate linear regression analysis, PhA (b=-1.266, p<0.001), LTM (b=0.987, p<0.001), age (b=-0.307, p<0.001) were independent predictors of OH. Conclusions This study demonstrated that age, LTM and especially PhA, had important roles in predicting OH in healthy Chinese individuals. In the future, PhA may aid in clinical assessment by helping to titrate dry weight among hemodialysis patients with malnutrition.

The use of motion capture has increased from last decade in a varied spectrum of applications like film special effects, controlling games and robots, rehabilitation system, animations etc. The current human motion capture techniques use markers, structured environment, and high resolution cameras in a dedicated environment. Because of rapid movement, elbow angle estimation is observed as the most difficult problem in human motion capture system. In this paper, we take elbow angle estimation as our research subject and propose a novel, markerless and cost-effective solution that uses RGB camera for estimating elbow angle in real time using part affinity field. We have recruited five (5) participants of (height, 168 ± 8 cm; mass, 61 ± 17 kg) to perform cup to mouth movement and at the same time measured the angle by both RGB camera and Microsoft Kinect. The experimental results illustrate that markerless and cost-effective RGB camera has a median RMS errors of 3.06° and 0.95° in sagittal and coronal plane respectively as compared to Microsoft Kinect.

Star image registration is the most important step in the application of astronomical image differencing, stacking and mosaicking, which requires high robustness, accuracy and real--time of the algorithm, but there is no high--performance registration algorithm in this field. In this paper, we propose a star image registration algorithm that relies only on radial module features (RMF) and rotation angle features (RAF), which has excellent robustness, high accuracy, and good real--time performance. The test results on a large amount of simulated and real data show that the comprehensive performance of the proposed algorithm is significantly better than the four classical baseline algorithms in the presence of rotation, insufficient overlapping area, false stars, position deviation, magnitude deviation and complex sky background, which is a more ideal star image registration algorithm.

In this project, our foremost intention is to analyze the angle of deflection of photon by NED black holes with many horizons in the context of non-linear electrodynamics. For the accomplishment of our intention at first we manipulated the optical metric of the desired black holes for the calculation of Gaussian curvature. After that, the angle of deflection in leading orders is attained from the desired black holes in weak field limit by using the famous Gauss-Bonnet theorem. Moreover, we evince the effect of plasma medium on the angle of deflection. At last, the graphical impact of the angle of deflection for NED black holes with many horizons is examined with respect to black hole charge and impact parameter in both the plasma and non plasma medium. In addition, we discuss the rigorous bound for grey body factor of the desired black hole and also observer its graphical behavior.

Ascorbate; Pars Plana Vitrectomy; Open Angle Glaucoma; Oxidative Stress; Vitreous Me-tabolism 0. How to Use This Template

In this paper, we calculate the deflection angle of photon by Casimir wormhole in the weak field limit approximation. First we calculate Gaussian optical curvature with the help of optical spacetime geometry and so we use the Gauss-Bonnet theorem on the Gaussian optical metric. Then we find the deflection angle of photon by Casimir wormhole. Moreover, we calculate the photon's deflection angle in the presence of plasma medium and we also see the graphical nature of deflection angle in both cases. Second, we move towards the shadow of Casimir wormhole. After the observations of Event Horizon Telescope, the study of shadow become very important so that we plot the shapes of shadow of Casimir wormhole, and we calculate the photon geodesic around the Casimir wormhole.

In this paper, we proposed a new model of non-linear electrodynamics with parameter. Firstly, we study the weak limit approximation and by using the Gauss Bonnet theorem, we obtain the deflection angle of photon from magnetized black hole and effect of bnon-linear electrodynamics. In doing so, we find the corresponding optical metric after that we calculate the Gaussian curvature which is used in Gauss Bonnet theorem. Then we show the deflection angle in the leading order terms. We also analyzed that our results reduces into Maxwell's electrodynamics and RN solution with the reduction of parameters. Moreover, we also investigate the graphical behavior of deflection angle w.r.t correction parameter, black hole charge and impact parameter.

This article deals with an analytical approach to determining the stress state in trochoidal profiles under shear bending. The transverse shear stresses cannot be neglected, especially in the case of (space-saving) shafts with a low aspect ratio (l/d). In addition to bending stresses, the transverse shear stresses are a significant component of the principal stresses. The approach is based on a formulation of the elastic behavior of a non-circular-profiled shaft using complex stress functions, according to Muskhelishvili. In order to determine the shear stresses, similar to the torsion load case, a conformal mapping must be found that can completely transform the unit circle in the model plane to the profile area in the real plane. For simple and higher epiotrochoidal profiles, an exact and complete mapping was determined from the contour equation. The method was applied to such profiles as an example. Equations were derived to determine the maximum shear and bending stresses and the bending deformations. For practical applications, additional equations for the main stresses that are decisive in dimensioning were determined. Accompanying numerical investigations were carried out and compared with the analytical results, where a very good agreement was observed.

The three-point bending behavior of a single Au nanowire deformed with an atomic force microscope was monitored by coherent X-ray diffraction using a sub-micrometer sized hard X-ray beam. While three-dimensional reciprocal-space maps were recorded before and after deformation by standard rocking curves, they were measured by scanning the energy of the incident X-ray beam during deformation at different loading stages. The mechanical behavior of the nanowire is visualized in reciprocal space and a complex deformation mechanism is described. In addition to the expected bending of the nanowire, torsion is detected. Bending and torsion angles are quantified from the high resolution diffraction data.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

Thin-wall heat pipe is an efficient heat transfer component, which has been widely used in the field of heat dissipation of high-power electronic equipment in recent years. In this study, the orange peel morphology defect of thin-wall heat pipes after bending deformation was analyzed both for the macro 3D profile and for the micro-formation mechanism. The results show that after high temperature sintering treatment, the matrix grains of heat pipe are coarsened seriously and formed a strong Goss texture, while a certain annealing twins with the unique Copper orientation are retained. The distribution of Schmid factor value subjected to the uniaxial stress indicate the inhomogeneity of intergranular deformation exist among the annealing twins and matrix grains. The annealing twin exhibit a “hard-oriented” component during the deformation; thus, it plays a role as barrier and hinder the slipping of dislocation. As the strain accumulates, part of the annealing twins may protrude from the surface of heat pipe, forming a large-scale fluctuation of the surface as the so called the “orange peel” morphology. The 3D profile shows the bulged twins mostly perpendicular to the drawing direction, with about 200-300μm in width and 10-20μm in height.

Keywords: SAR; interferometry; bistatic

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

The apparent shape of the black hole shadow provides a full description of the spin, the inclination angle and the charge of a Kerr black hole, without any astrophysical process or underlying theory in the astrophysical process.

Traditional winglets are designed as fixed devices attached at the tips of the wings. The primary purpose of the winglets is to reduce the lift-induced drag, therefore improving aircraft performance and fuel efficiency. However, because winglets are fixed surfaces, they cannot be used to control lift-induced drag reductions or to obtain the largest lift-induced drag reductions at different flight conditions (take-off, climb, cruise, loitering, descent, approach, landing, and so on). In this work, we propose the use of variable cant angle winglets which could potentially allow aircraft to get the best all-around performance (in terms of lift-induced drag reduction), at different flight phases. By using computational fluid dynamics, we study the influence of the winglet cant angle and sweep angle on the performance of a benchmark wing at Mach numbers of 0.3 and 0.8395. The results obtained demonstrate that by adjusting the cant angle, the aerodynamic performance can be improved at different flight conditions.

Centimeter-level localization and rotation angle estimation of flatbed trucks are major problems in unmanned forklift automated loading scenes. To solve it, this study proposes a method for high-precision positioning and rotation angle estimation of flatbed trucks based on BeiDou and vision. First, an unmanned forklift equipped with a ToF camera and double antenna mobile receiver for BeiDou positioning collects depth images and localization data near the front and rear endpoints of the flatbed. Then DDRNet-23-slim was used to segment the flatbed from the depth image and extract the straight lines at the edges of the flatbed using the Hough transform and compute the set of intersection points of the lines. A neighborhood feature vector was designed to locate the endpoint of a flatbed from a set of intersection points by feature screening. Finally, the relative coordinates of the endpoints were converted to a customized forklift navigation coordinate system by BeiDou positioning, and rotation angle estimation was performed by the front and rear endpoints. Experiments showed that the endpoint positioning error was less than 3 cm and the rotation angle estimation error was less than 0.1°. The precision of the method meets the demand for automated flatbed truck loading by unmanned forklifts.

This paper is devoted to compute the weak deflection angle for Kalb-Ramond traversable wormhole solution in plasma and dark matter mediums by using the method of Gibbons and Werner. To acquire our results, we evaluate Gaussian optical curvature by utilizing the Gauss-Bonnet theorem in the weak field limits. We also investigate the graphical influence of deflection angle $\tilde{\alpha}$ with respect to the impact parameter $\sigma$ and minimal radius $r_0$ in plasma medium. Moreover, we derive the deflection angle by using different method known as Keeton and Petters method. We also examine that if we remove the effects of plasma and dark matter, the results become identical to that of non-plasma case.

Study of perihelion shift of Mercury and deflection angle are important aspects for the verification of general relativity. For Schwarzschild geometry both the perihelion shift and weak deflection angle were independent of charge whereas for ReissnerNordstrom space-time charge should effect on both the perihelion shift and deflection angle. This paper shows the perihelion shift decreases with the increases of charge. Effect of other parameters like angular momentum, mass parameter, distance of closest approach on perihelion precession and deflection angle has also discussed. This paper also includes the graphical behavior which verifes our theoretical calculations.

In this paper, we use a new asymptotically flat and spherically symmetric solution in the generalized Einstein-Cartan-Kibble-Sciama (ECKS) theory of gravity to study the weak gravitational lensing and its shadow cast. To this end, we first compute the weak deflection angle of generalized ECKS black hole using the Gauss–Bonnet theorem in plasma medium and in vacuum. Next by using the Newman-Janis algorithm without complexification, we derive the rotating generalized ECKS black hole and in the sequel study its shadow. Then, we discuss the effect of the ECKS parameter on the shadow of the black hole and weak deflection angle. In short, the goal of this paper is to give contribution to the ECKS theory and look for evidences to understand how the ECKS parameter effects the gravitational lensing.

Additive manufacturing (AM) are used in several industries such as automotive, aerospace, and medical sciences. One of the most common devices used in additive manufacturing is fused deposition modeling (FDM) 3D printers. This fabrication method has different inputs that affect the quality of the parts. In this research, the bending fatigue properties of polylactic acid (PLA) biomaterial made with a 3D printer are investigated. To demonstrate the influence of printing parameters on fatigue lifetime, standard specimens with nozzle diameters of 0.2-0.6 mm, extruder temperature of 180-240°C, and print speed of 5-15 mm/s were printed. After performing fully-reversed bending fatigue tests, it was found that printed specimens at 180°C have the best fatigue lifetime in most cases. Accordingly, fatigue behavior improved by reducing the nozzle diameter. Printing at lower temperatures also improved fatigue lifetime. The printing speed affected the slope of the S-N diagram, known as the fatigue strength exponent.

In this paper, we study the weak deflection angle using Gauss-Bonnet theorem and bounding greybody factor for electric and magnetic black holes in the background of nonlinear electrodynamics. Using Gibbons and Werner's approach, first we acquire the Gaussian optical curvature to use in Gauss-Bonnet theorem and calculate the bending angle for spherically symmetric electric and magnetic black holes in both non-plasma and plasma mediums in the weak field limits. Later, we calculate the rigorous bounds of the greybody factor for the given black holes. Furthermore, we look into the graphical behaviour of bending angles and greybody bounds at some specific values of multiple parameters as well as black holes charges. It is to be mention here that all the results for the electric and magnetic charged black holes solutions reduce into the Schwarzschild black hole solution in the absence of the black holes charges.

BACKGROUND: Scoliosis is a widespread musculoskeletal disorder of bending and twisting of spine. In this medical ailment, spine curves to the side and even in severe cases it can twist and can take several bends. For the diagnosis and treatment of scoliotic patients, the Cobb’s angle is a critical marker of the body’s curvature. OBJECTIVE: There are many researches that have been conducted to automate the manual measurement of the angle and every investigation has their own limita- tions. METHODS: This paper presents a method for precisely measuring the Cobb’s an- gle using deep learning based techniques. Mainly it comprises of feature enhance- ment of augmented dataset, a bespoke code for landmark estimation on the spine, segmentation model based on the U-Net architecture and a custom code for Cobb’s angle measurement. These measured angles are then compared to the given angles for the segmentation on biomedical (X-ray) images. RESULTS: The findings demonstrate that the proposed technique offers an auto- mated and impartial way for precisely measuring this angle with an overall accu- racy of 97% and Root Mean Square Error (RMSE) of 4.99, which can lower the variability, facilitate early detection, accurate diagnosis, and monitoring of scolio- sis progression. Additionally, it aids in the treatment planning and evaluating treat- ment outcomes. CONTRIBUTION: By leveraging the applications of Cobb’s angle measurement, healthcare professionals can enhance the quality of care and can improve long-term outcomes for individuals with scoliosis.

This study presents a detailed investigation of the application of superquadrics in small-angle scattering (SAS), a technique essential in materials science, biology, and physics for investigating structural properties at the nanoscale and microscale. Superquadrics, a family of geometric shapes known for their versatility in representing a wide range of forms, are employed to model complex structures in SAS studies. We examine the parametric nature of superquadrics and their ability to efficiently describe shapes from simple balls to intricate star-like forms. We demonstrate the application of superquadrics through a rigorous analysis of SAS simulated data, including scattering intensity patterns and pair-distance distribution functions. This allows us to reveal insights into key structural characteristics of various materials, such as the size and shape. We also demonstrate the efficacy of superquadrics in accurately modeling experimental small-angle X-ray scattering data from a chimeric protein complex, showcasing their potential in biological systems analysis. The findings offer a robust framework for future research and application in diverse fields, including materials science, nanotechnology, and bioengineering.

Infrared sensors are applied more and more widely in industrial production applications. Based on the theory of thermal radiation, this paper discusses the system design principle, temperature calibration method and thermal image analysis method in detail. The system has passed the measurement unit certification, showing that the field of view is 180°, the number of scanning points is 2048, the linear velocity is 10-100Hz, the spatial resolution is 2.5mrad, and the precision is ±1℃. On-line monitoring test has been done in the steelmaking plant of Bao Steel. The results show that the system has strong anti-interference ability, stability and reliability, and meets the application requirements of online monitoring.

In this paper, we study light rays in a Kazakov-Solodukhin black hole. To this end, we use the optical geometry of the Kazakov-Solodukhin black hole within the Gauss-bonnet theorem. We first show the effect of the deformation parameter $a$ on the Gaussian optical curvature, and then we use the modern method popularized by Gibbons and Werner to calculate the weak deflection angle of light. Our calculations of deflection angle show how gravitational lensing is affected by the deformation parameter $a$. Moreover, we demonstrate the effect of a plasma medium on weak gravitational lensing by the Kazakov-Solodukhin black hole. We discuss that the increasing the deformation parameter $a$, will increase the weak deflection angle of the black hole. Our analysis also uncloak how one may find a observational evidence for a deformation parameter on the deflection angle.

In this work, a tool for estimating the contact angle from the molecular dynamics simulations is developed and presented. The tool (Achilles) can detect water droplet on hydrophobic and hydrophilic surfaces. The tool can reconstruct the droplets broken across the periodic boundaries. Further a neighbor density based accurate filter is used to find the droplet liquid vapor interface and a circle is fitted using it after removing the dense layers of water next to solid surface. This fitted circle is solved for contact angle and results are outputted in the form of graphical images and text. The entire content of the internal computations of the tool is broken down into 4 phases and users can monitor the outcomes at every phase through output images. The tool is tested using sample molecular dynamics results of water droplet on hydrophobic and hydrophilic surfaces. We believe this tool can be a good addition to the molecular dynamics simulation community who work on the interfacial physics, droplet evaporation, super hydrophobic surfaces, and wettability etc.

We study the light rays in a static and spherically symmetric gravitational field of null aether theory (NAT). To this end, we employ the Gauss-Bonnet theorem to compute the deflection angle by a NAT black hole in the weak limit approximation. Using the optical metrics of the NAT black hole, we first obtain the Gaussian curvature and then calculate the leading terms of the deflection angle. Our calculations show how gravitational lensing is affected by the NAT field. We also show once again that the bending of light stems from a global and topological effect.

Abstract: Characterization the 3-D structure of clouds is needed for a more complete understanding of the Earth's radiative and latent heat fluxes. Here we develop and explore a “ray casting” algorithm applied to the Multi-angle Imaging SpectroRadiometer (MISR) on board the Terra satellite, to reconstruct 3-D cloud volumes for observed clouds. The ray casting algorithm is first applied to geometrically simple synthetic clouds to show that, under the assumption of perfect, clear-conservative cloud masks, the reconstruction method yields overestimation whose magnitude depends on the cloud geometry and the resolution of the reconstruction grid relative to the image pixel resolution. The method is then applied to two select MISR scenes, fully accounting for MISR’s viewing geometry for reconstructions over the Earth’s ellipsoidal surface. The MISR Radiometric Camera-by-camera Cloud Masks at 1.1 km resolution and custom cloud masks at 275 m resolution independently derived from MISR RGB channels are used as input cloud masks. A wind correction method, termed “cloud spreading”, is devised and applied to the cloud masks to offset potential cloud movements over short time intervals (around 7 minutes at maximum) between the cameras. The MISR cloud top height product is used as a constraint to reduce the overestimation at the cloud top. The reconstruction results show that their uncertainty is significant when the wind correction is applied, and that they have more refined structures when the input cloud mask has a higher resolution. Recommendations for improving the presented cloud volume reconstructions as well as for future passive remote sensing satellite missions are discussed.

Toshiba devised the bladeless fan (or Air Multiplier) concept in 1981. Researchers like James Dyson and Jafari et al. further developed it. Bladeless fans are more energy-efficient, safer due to the hidden blades, easier to clean, and more adjustable than conventional fans. From a performance point of view, bladeless fans are better because they multiply mass flow rate, eliminate buffeting, consume less power, and are quieter. This paper investigates the influence of the airfoil’s outlet slit thickness on the discharge ratio by varying the outlet slit thickness of an Eppler 473 airfoil from 1.2 mm to 2 mm in intervals of 0.2 mm. Results indicated that smaller slits showed higher discharge ratios. The airfoil with a 1.2 mm slit thickness showed a discharge ratio of 18.78, a 24% increase from the discharge ratio of the 2 mm slit. The effect of outlet angle on the pressure drop across the airfoil was also studied. Outlet angles were varied from 16∘ to 26∘ by an interval of 2∘. The airfoil profile with a 24∘ outlet angle showed a maximum pressure difference of 965 Pa between the slit and leading edge. In contrast, the 16∘ outlet angle showed the least pressure difference of 355 Pa. Parameters such as average velocity, turbulent kinetic energy, the standard deviation of velocity and outlet velocity magnitude was used to assess the performance of airfoil profiles used in bladeless fan.

Given the high number of vehicle-crash victims, it has been established as a priority to reduce this figure in the transportation sector. For this reason, many of the recent researches are focused on including control systems in existing vehicles, to improve their stability, comfort and handling. These systems need to know in every moment the behavior of the vehicle (state variables), among others, when the different maneuvers are performed, to actuate by means of the systems in the vehicle (brakes, steering, suspension) and, in this way, to achieve a good behavior. The main problem arises from the lack of ability to directly capture several required dynamic vehicle variables, such as roll angle, from low-cost sensors. Previous studies demonstrate that low-cost sensors can provide data in real-time with the required precision and reliability. Even more, other research works indicate that neural networks are efficient mechanisms to estimate roll angle. Nevertheless, it is necessary to assess that the fusion of data coming from low-cost devices and estimations provided by neural networks can fulfill the reliability and appropriateness requirements for using these technologies to improve overall safety in production vehicles. Because of the increasing of computing power, the reduction of consumption and electric devices size, along with the high variety of communication technologies and networking protocols using Internet have yield to Internet of Things (IoT) development. In order to address this issue, this study has two main goals: 1) Determine the appropriateness and performance of neural networks embedded in low-cost sensors kits to estimate roll angle required to evaluate rollover risk situations. 2) Compare the low-cost control unit devices (Intel Edison and Raspberry Pi 3 Model B), to provide the roll angle estimation with this artificial neural network-based approach. To fulfil these objectives an experimental environment has been set up composed of a van with two set of low-cost kits, one including a Raspberry Pi 3 Model B, low cost Inertial Measurement Unit (BNO055 - 37€) and GPS (Mtk3339 - 53€) and the other having an Intel Edison System on Chip linked to a SparkFun 9 Degrees of Freedom module. This experimental environment will be tested in different maneuvers for comparison purposes. Neural networks embedded in low-cost sensor kits provide roll angle estimations very approximated to real values. Even more, Intel Edison and Raspberry Pi 3 Model B have enough computing capabilities to successfully run roll angle estimation based on neural networks to determine rollover risks situation fulfilling real-time operation restrictions stated for this problem.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

Carbon fiber reinforced polymer (CFRP) bending structure is widely used in the aviation field. The occurrence and propagation of delamination damage will reduce the safety of in-service bending structures. As a detection tool with high damage sensitivity, Lamb wave can effectively identify delamination damage. In this study, the signal difference coefficient (SDC) was introduced to quantify delamination damage and evaluate the sensitivity of A0 and S0 mode lamb waves to delamination damage. The simulation results show that compared with the S0 mode Lamb wave, the A0 mode Lamb wave exhibits higher delamination damage sensitivity. The delamination damage can be quantified based on the strong correlation between the SDC and the delamination damage size. The control effect of the linear array PZT phase time-delay method on Lamb wave mode was investigated by simulation. The phase time-delay method realizes the generation of a single-mode Lamb wave, which can separately excite the A0 mode and S0 mode Lamb wave to identify delamination damage of different sizes. The A0 mode Lamb wave was excited by the developed one-dimensional linear comb transducer (LCT), which was used to conduct the detection experiment on the CFRP bending plate with delamination damage sizes of Φ6.0 mm, Φ10.0 mm, and Φ15.0 mm. The experimental results verify the correctness of the simulation. According to the Hermite interpolation results of the finite-element simulation data, the relationship between the delamination damage size and the SDC was fitted by the Gaussian function, which can accurately quantify the delamination damage. The absolute error of the delamination damage quantification with fitting expression is not larger than 0.8 mm, and the percentage error is not more than 8%.

Fused silica glass is a material with outstanding mechanical, thermal and optical properties. Being a brittle material, it is challenging to shape. In the last decade, the manufacturing of monolithic flexible mechanisms in fused silica has evolved with the femtosecond laser-assisted etching process. However, instrumenting those structures is demanding. To address this obstacle, this article proposes to inscribe a Bragg Grating sensor inside a flexure and interface it with an optical fibre to record the strain using a spectrum analyzer. The strain sensitivity of this Bragg Grating sensor is characterized at 1.2 pm/μϵ (1 μϵ = 1 microstrain). Among other applications, deformation sensing can be used to record a force. Its use as a micro-force sensor is estimated. The sensor resolution is limited by our recording equipment to 30 μN over a measurement range above 10 mN. This technology can offer opportunities for surgery applications or others where precision and stability in harsh environments are required.

The paper presents section models for analysis of the resistance of RC members subjected to bending moment with or without axial force. To determine the section resistance the nonlinear stress-strain relationship for concrete in compression is assumed, taking into account the concrete softening. It adequately describes the behavior of RC members up to failure. For the reinforcing steel linear elastic-ideal plastic model is applied. For the ring cross-section subjected to bending with axial force the normalized resistances are derived in the analytical form by integrating the cross-sectional equilibrium equations. They are presented in the form of interaction diagrams and compared with the results obtained by testing conducted on RC columns under eccentric compression. Furthermore, the ultimate normalized bending moment has been derived for the rectangular cross-section subjected to bending without axial force. It was applied in the cross-sectional analysis of steel and concrete composite beams, named BH beams, consisting of the RC rectangular core placed inside a reversed TT welded profile. The comparisons made indicated good agreements between the proposed section models and experimental results.

Gold nanohole arrays are periodic metastructures gathering huge interest for biosensing applica-tions. The grating-like structure defines their plasmonic mode features and their angular disper-sion can be used to highlight efficiently their interaction with the fluorescence emission of a properly tuned fluorophore. Resorting to a properly tuned/engineered/optimised plasmonic na-nohole array and a commercial organic dye, we performed an accurate resolved angle-resolved optical characterization. The plasmonic fingerprints was consequently identified as a modification of the dye photoluminescence signal in terms of both spectral redistribution and enhancement. Interestingly, by analyzing the results, an advantageous measurement configuration can be iden-tified to better engineer a suitable platform for efficiency maximization in plasmon-enhanced flu-orescence-based applications. Therefore, the coupling mechanism with the plasmonic modes, and nanostructure properties can be carefully co-optimized.

In the full load operating range, wind turbines typically use pitch control to maintain rotor speed and output power at their rated values to guarantee the whole system’s safety. Blade pitch actuators are subject to physical limitations and safety requirements, which imposes strict constraints on pitch angle’s amplitude and rate of change. These constraints will bring windup problem to the integral part of the pitch controller. It leads to deterioration of the pitch control system’s performance or even the instability problem, especially for large-scale turbines operating in extreme uncertain wind conditions or suffering from cyber attacks. This paper designs an anti-windup robust pitch angle control strategy to deal with pitch rate constraint issue to enhance the security of control system. First, to facilitate controller design, a filtered tracking error technique is employed to transform the nonaffine form into an affine one. Subsequently, a feedback robust controller based on UDE is developed to handle the model’s uncertainty and external disturbances. To address the issue of integral saturation in the pitch system and guarantee its safety, an elliptical bounded constraint is integrated into the designed UDE strategy. This bounded UDE controller can improve the stability of power generation quality, reduces the mechanical loads on components and enhance the whole system’s safety. Finally, the effectiveness of the proposed scheme is verified on the Wind Turbine Blockset platform in Matlab/Simulink. It can achieve better performance than the traditional method.

Background: The variability of the obtained results of manual tests assessing the angle of strabismus depends on the experience, skills, and training of the examiner. The authors hope that the new measuring device will provide a more sensitive and repeatable method for detecting small strabismus angles compared to the gold standard – PCT. The purpose of this article is to present an innovative strabismus angle demonstration device, called Strabiscan, to present automated measurements of eye deviation, and to compare the obtained results of these measurements to the traditional manual method. Methods: In patients with the manifest strabismic disease (n = 30) and a group of healthy subjects (n = 30), a detailed history was taken and routine ophthalmologic examinations were performed, including best-corrected distance visual acuity, assessment of refractive error using an autorefractometer after cycloplegia, biomicroscopic evaluation of the anterior segment of the eye, and evaluation of the eye fundus by indirect ophthalmoscopy. Subsequently, each patient and healthy subjects were subjected to a prismatic cover-uncover test using a manual method, and then the presence of strabismus was detected and its angle assessed using demonstration Strabiscan device. Results: In the control group, using the Strabiscan demonstration device, small-angle latent strabismus ≤3DP was diagnosed in 83% of patients, and >3DP in 13%. In contrast, using the prismatic cover-uncover test, latent strabismus ≤3DP was diagnosed in only 13% of patients, and latent strabismus with an angle >3DP in 13% of patients. No statistically significant differences were noted in the measurements of strabismus angles made by the different methods. Conclusions: The Strabiscan demonstration device allows quick and accurate assessment of the strabismus angle. Compared to the prismatic cover-uncover test, it has a higher sensitivity for detecting low-angle latent strabismus. Measurements with the Strabiscan do not require the presence of additional co-assistants for the test.

In this paper a new approximate procedure is developed for calculating the inclination angle of the end points of statically determinate beams. The method is based on the topology comparison of simple (hinge-roller combination) supported beam and a resemblant cantilever beam. Assuming that the support reactions of the beam are active forces, the virtual displacements at the points of the reaction forces are calculated. Based on these values the inclination angle is calculated. Several examples are considered and the suggested in this paper, while the procedure is applied for various types of structures and loadings. The results, obtained by the suggested numerical procedure, are compared with analytical ones, and they are in good agreement.

Gesture recognition technology has been quickly developed in the field of human-computer interaction. The multiple-input multiple-output (MIMO) radar has been widely adopted in gesture recognition because of its notable spatial resolution. In this work, a highly accurate MIMO radar-based hand gesture recognition algorithm with very low complexity is proposed. To make the proposed system applicable in the industry and work well even when the size of the training data is limited, we applied several low-complexity adaptive signal processing methods to extract features and reduce the noise effect. First, spectrum analysis is applied to range-Doppler maps (RDMs) and a cell-averaging constant false alarm rate (CA-CFAR) with mirror filters is applied to improve the robustness to noise. Afterward, the features related to the distance, speed, direction, and the elevation angle of the moving object are determined by the proposed adaptive signal analysis techniques and the random forest is applied for classification. The proposed system has the capability to precisely distinguish and identify eight motions, including waving, moving to the left or right, patting, pushing, pulling, and rotating clockwise or anticlockwise, with an accuracy of 95%. Experiments demonstrate the capability of the proposed hand gesture recognition system to classify different movements precisely.

In this paper, an ultracompact combined sensor for displacement and angle synchronous measurement is proposed based on self-imaging effect of optical microgratings. Using a two-grating structure, linear and angular displacement can be measured by detecting the change of phase and amplitude of the optical transmission respectively within one single structure in meantime. The optical transmitted properties of the two-grating structure are investigated in both theory and simulation. Simulated results indicate that, the optical transmission changes in a sinusoidal relationship to the input linear displacement. Meanwhile, the amplitude of the curve decreases with an input pitch angle, indicating the ability for synchronous measurement within one single compact structure. The synchronous measurement of the linear displacement and the angle is also demonstrated experimentally. The results show a resolution down to 4nm for linear displacement measurement, and a sensitivity of 0.26mV/arcsec within a range of ±1° for angle measurement. Benefitting from a simple common-path structure without using optical components including reflectors and polarizers, the sensor shows an ultrahigh compactness for multiple-degrees-of-freedom measuring, indicating the great potential for this sensor in the fields such as integrated mechanical positioning and semiconductor fabrication.

We have recently introduced the possibility of performing operando small-angle X-ray scattering measurements using a novel industrially relevant injection moulding system for plastics. We show that useful time-resolving measurements can be performed with a time-cycle of 1s and we highlight the possible steps to reduce this to 0.5s. We show how we can use the transmission measurements to provide a time-marker when plastic first enters the mould cavity in the region probed by the incident X-ray beam. We show the opportunities provided by this experimental stage mounted on the NCD-SWEET beamline at ALBA to probe the reproducibility of the injection moulding system on different scales. The design of the equipment allows the development of the structure and the morphology to be evaluated in different parts of mould cavity and we evaluate any differences in a rectangular mould cavity. We identify future prospects for this equipment in terms of novel mould heating and cooling systems and the opportunities for quantitatively evaluating radical approaches to injection moulding technology.

The logarithmic correction to Bekenshtein$-$Hawking entropy in the framework of 4D Einstein - Gauss - Bonnet gravity coupled with nonlinear electrodynamics is obtained. We explore the black hole solution with the spherically symmetric metric. The logarithmic term in the entropy has a structure similar to the entropy correction in the semi-classical Einstein equations which mimics the quantum correction to the area low. The energy emission rate of black holes and energy conditions are studied. The quasinormal modes of a test scalar field are investigated. The gravitational lensing of light around BHs was studied. We calculated the deflection angle for some model parameters.

Running on a non-motorized, curved-deck treadmill is thought to improve gait mechanics. It is not known, though, if the change in gait carries over to running on a motorized treadmill or level ground. To determine the effect of running on a curved non-motorized treadmill (CNT) on gait characteristics measured during a subsequent bout of running on a traditional motorized treadmill (TMT). Sixteen healthy college-aged participants, age (mean±SD) 20.4±1.6 years volunteered to have their gait analyzed while running on a TMT and CNT. After familiarization and warm-up on both treadmills, each subject completed five, 4-minute bouts of running alternating between traditional motorized and curved non-motorized treadmills: TMT-1, CNT-1, TMT-2, CNT-2, and TMT-3. Variables of interest included step length (m), stride length (m), imbalance score (%), and step angle (°) and were measured using Optogait gait analysis equipment. Differences in gait char acteristics among TMT-1, TMT-2, and TMT-3 can be attributed to running on the CNT. The results show that running on a CNT resulted in significant changes in gait characteristics. These findings suggest that running on a CNT can significantly alter gait characteristics may result in improvements in running gait that persist to subsequent running on a TMT.

This paper presents a complete control strategy of the active return-to-center (RTC) control for electric power steering (EPS) systems. We first establish the mathematical model of the EPS system and analyze the source and influence of the self-aligning torque (SAT). Second, based on the feedback signals of steering column torque and steering wheel angle, we give the trigger conditions of a state switch between the steering assist state and the RTC state. In order to avoid the sudden change of the output torque for the driving motor when the state switches frequently between the steering assist state and the RTC state, we design an undisturbed state switching logic algorithm. This state switching logic algorithm ensures that the output value of the RTC controller is set to an initial value and increases in given steps up to a maximum value after entering the RTC state, and the output value of the RTC controller will reduce in given steps down to zero when exiting the RTC state. This therefore ensures smooth switch control between the two states and improves the driver’s steering feeling. Third, we design the RTC controller, which depends upon the feedback signals of the steering wheel angle and the angular velocity. In addition, the controller increases the auxiliary control function of the RTC torque based on vehicle speed. The experimental results show that the active RTC control method does not affect the basic assist characteristics, which effectively reduces the residual angle of the steering wheel at low vehicle speed and improves the RTC performance of the vehicle.