As the control brain of the petrochemical plant, blast resistant performance requirements of the petrochemical control room should be guaranteed when the vapor cloud explosion occurs in the petrochemical production process. 3D-Kagome truss core sandwich structure is a kind of blast resistant material with high energy absorption. Considering the influence factors of the radius of the truss core rod and thickness of the upper and lower panels, in this paper, blast resistant performance of a real steel petrochemical control room with 3D-Kagome truss core sandwich wall is analyzed. With the optimization goal of plastic deformation energy and panel displacement, the optimal wall thickness and radius of the truss core rode are obtained. The optimized blast resistant wall is assembled, and the dynamic response of the steel petrochemical control room with the 3D-Kagome truss core sandwich blast resistant wall is analyzed. The simulation results show that the truss core layer does not dissipate the blast energy effectively when the radius ratio of the truss core rod is larger than 2.7% of the total thickness of the wall; with the increase of the thickness of the upper and lower panels, the proportion of plastic deformation energy of the truss core layer increases gradually and then tends to be a stable proportion value, that is about 90%; When the thickness ratio of the panel is 6.7% of the total one of the wall and the radius ratio of the truss core rod is 2.7% of the total thickness of the wall, the optimal blast resistant 3D-Kagome sandwich wall is determined.

In the recent concrete industry, high fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high fluidity concrete that using mass of fly ash as alternative materials of cement. The high fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high fluidity concrete containing high volume fly ash was evaluated that fluidity, compressive strength, heat of hydration and drying shrinkage of concrete.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Rice blast and brown planthopper (BPH) are two of the most destructive diseases and pests in rice (Oryza sativa L.) production in China. The development of multi-resistant varieties is widely recognized as the most efficient and environmentally friendly approach to controlling crop diseases and pests. Functional molecular markers (FMMs) have been developed from functional variants in the genic region associated with trait variation, greatly enhancing the efficiency of identifying and pyramiding valuable genes in crop breeding. In this study, two FMMs and a multiplex PCR amplification system were developed for two major broad-spectrum BPH resistance genes, Bph6 and Bph9. By assistance of FMMs in multi-resistant rice restorer line development pipeline, two lines (Huahui7713 and Huahui3006) with blast and BPH resistance were developed by pyramiding three resistance genes Pigm, Bph6 and Bph9. Huahui7713 and Huahui3006 as male lines, two new hybrid rice varieties (WeiLiangYou7713 and Xuanliangyou3006) were certificated and commercial released in China. WeiLiangYou7713 and Xuanliangyou3006 showed improved blast and BPH resistance, and no penalty on yield and grain-quality. Annual promotion area of WeiLiangYou7713 has exceeded 53.3 thousand hectares, indicating its widespread adoption and success in the market. Huahui7713 and Huahui3006 could have great potential for utilization in blast and BPH resistance rice breeding.

In chronic myeloid leukemia (CML), a clonal proliferative disorder of granulocytic lineage, the 90%‐95% of cases are characterized by t(9;22) (q34.1;q11.2) translocation, leading to the Philadelphia chromosome (1). Rarely, CML patients directly present a blast crisis, mostly of myeloid origin (2, 3). Herein, we describe one rare CML case, showing an unusual early T lymphoid blastic crisis.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

The performance of OpenFOAM in strong scaling tests on HPC systems with AMD EPYC processors exhibits a pronounced superlinear speedup. Simple test cases show superlinear speedups of over 300%, which significantly impacts the efficient use of computing resources. With the last generation of HPC architectures, a superlinear speedup of about 10% to 20% was well expected and accepted by CFD users. The measured superlinear speedup is much more pronounced and withstands the communication overhead to even larger scales. A detailed performance analysis of OpenFOAM follows, employing various High-Performance Computing (HPC) architectures, including AMD, ARM and Intel systems. The performance metric FVOPS (Finite VOlumes solved Per Second) is introduced to compare the performance of Computational Fluid Dynamics (CFD) applications when varying the grid size, as occurs in a strong scaling test. The achievable FVOPS depends on various factors, including the simulation type, boundary conditions, and especially the grid size of a use case. Analysing FVOPS on a single node level with varying grid size shows a significant difference in performance and cache utilization, which explains the large superlinear speedups seen in the strong scaling tests. Furthermore, FVOPS can be used as a simple benchmark to determine the optimal number of grid elements per rank to simulate a given use case at peak efficiency on a given platform, resulting in time, energy, and cost savings. The FVOPS metric also facilitates the direct comparison between different HPC architectures. The tests using AMD, ARM, and Intel processors show a peak in performance when employing around 10,000 grid elements per core. The presence of a large L3 cache on AMD processors is particularly advantageous, as indicated by L3 cache miss rates observed on AMD EPYC processors. Our results suggest that future HPC architectures with larger caches and higher memory bandwidth would benefit the CFD community.

Fires constitute a significant threat due to the pollutants emitted and the destruction they cause. People who take part in fire-fighting operations must be equipped with appropriate tools, including special clothing that will allow them to work and guarantee safety. One of the threats are compounds from the PAH group, which are characterized by high toxicity and carcinogenicity. Therefore, it is important that the materials used constitute a barrier to contamination. Various materials from which individual elements of special firefighter's clothing are made were tested. Additionally, the importance of height on the possibility of sorption of PAH compounds on a given type of material was analyzed. Based on the results obtained, it was found that the type of material and the zone in which the clothing items are used are important in the sorption processes of pollutants. Data in this area may be important for taking further actions regarding the modification of materials used in special fire brigade clothing and in their cleaning processes.

As a representative of Exponential Organizations, MI went from obscurity to the Fortune 500 in just ten years. Mi's success is inextricably linked to its outstanding business model. This paper summarizes the elements of MI's business model from four perspectives: value proposition, value creation, value delivery, and value capture, as well as its measures for developing into an exponential organization. Expecting to provide theoretical references for the transformation and upgrading of manufacturing organizations.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

(1) Background: The aim of the research was to present and emphasize the importance of magnetic resonance imaging (MRI) in diagnosing Achilles tendon (AT) ruptures by presenting case reports. (2) Materials and Methods: The sample of respondents included 7 patients (4 males and 3 females, 2 athletes and 5 non-athletes), aged 25 to 58 years, with AT injuries, who were examined and treated at the Institute for Treatment and Rehabilitation "Niška Banja", Niš, Serbia. Ankle examinations with MRI were conducted using the Esaote O-scan 0.3 T machine. The examinations were performed without the application of a paramagnetic contrast agent and without the use of anesthesia. Results: The MRI method's sensitivity and overall diagnostic accuracy were excellent, with 100% true positives. In our study, the method accurately detected the presence, location, and severity of AT injuries in all cases. MRI is an important and reliable method for detecting AT injuries, classifying them, monitoring the course of recovery, and assessing the effects of therapy. Conclusions: An unrecognized or delayed diagnosis of an AT injury can lead to chronic changes. Timely diagnosis (clinical examination, ultrasonography, magnetic resonance imaging) and appropriate treatment (conservative or operative) enable patients to return to normal activities, including sports. Unfortunately, the use of MRI is limited by restricted access and the cost of the examination.

Ice and snow on roads in winter endanger traffic safety. The existing methods of snow and ice removal have various drawbacks, which need further research. Aiming at solving limitations about high labor intensity, low efficiency, serious environmental pollution of traditional snow and ice removal methods, the anti-icing coating technology of high-voltage conductors is used for reference, and in view of the characteristics of asphalt pavement deicing, an ice-suppressing material that can effectively reduce the adhesion between snow, ice and pavement is successfully developed. As there is no perfect evaluation index and method for ice-suppressing materials at present, this paper further evaluates the performance of ice-suppressing materials from the aspects of deicing performance, durability, adhesion and the impact of ice-suppressing materials on pavement performance. The test results show that the ice-suppressing material can effectively reduce the adhesion between the ice layer and the specimen, making it easier to remove. The ice-suppression material has good slow-release performance, and the specimens still have good deicing performance after 7 cycles of tests.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

Methicillin-resistant Staphylococcus aureus (MRSA) infections, in particular biofilm-organized bacteria, remain a clinical challenge and a serious health problem. Rifabutin (RFB), an antibiotic of the rifamycins class, has shown in previous work excellent anti-staphylococcal activity. Here, we proposed to load RFB in liposomes aiming to promote the accumulation of RFB at infected sites and consequently enhancing the therapeutic potency. Two clinical isolates of MRSA, MRSA-C1 and MRSA-C2, were used to test the developed formulations, as well as the positive control, vancomycin (VCM). RFB in free and liposomal forms displayed high antibacterial activity, with minimal inhibitory concentrations (MIC) ranging from 0.009-0.013 μg/mL and MBIC50 values ranging from 0.008-0.012 μg/mL, in planktonic and biofilm bacteria, respectively. Confocal microscopy studies demonstrated the rapid internalization of unloaded and RFB-loaded liposomes in the bacterial biofilm matrix. In murine models of systemic MRSA-C1 infection, Balb/c mice were treated with RFB formulations and VCM at 20 and 40 mg/kg of body weight, respectively. Obtained data proved the superior therapeutic effectiveness of RFB formulations compared to Control and VCM groups even using a two-fold lower therapeutic dose as demonstrated by significantly reduced bacterial burden and growth index values in major organs. In addition, RFB formulations were the only formulations associated with 100% survival. Globally, this study emphasizes the potential of RFB nanoformulations as an effective and safe approach against MRSA infections.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

Long span cable-stayed bridge is the main bridge type with a span of more than 400 meters. It is generally designed as a double tower long-span structure with good spanning capacity and economic performance. Wind resistance safety performance is the main index to control the long-span cable-stayed bridge structure. During the operation of long-span cable-stayed bridge structure, because the service life of the cable is far less than the design life of the structure, the wind resistance performance of the structure will inevitably deteriorate significantly, which will seriously affect the structural service performance of symmetric cable-stayed bridge. Based on symmetric reliability theory, this paper takes flutter and static wind stability of long-span cable-stayed bridge structure as the main design control index, uses positive reliability theory to calculate the reliability index of symmetric cable-stayed bridge structure, uses inverse reliability theory to calculate the safety factor of symmetric cable-stayed bridge structure, and evaluates the wind resistant time-varying performance of long-span cable-stayed bridge structure by comprehensively considering the reliability index and safety factor. Taking a practical project of a long-span cable-stayed bridge as a specific case, the wind resistant time-varying reliability of the bridge during its operation for more than 30 years is analyzed, and the parameter sensitivity is analyzed. The results show that the wind resistance performance of the cable-stayed bridge structure is obviously affected by the cable, and the degradation of the cable performance will have an important impact on the wind resistance time-varying performance of the structure, especially the critical wind speed of the structure has obvious time-varying characteristics. The safety factor and reliability index can objectively evaluate the wind resistance time-varying performance of the long-span cable-stayed bridge structure.

Correlations among estrus cycle, pyometra, and canine diabetes mellitus (CDM) have been described since the late 1950s, and substantial progress in understanding mechanisms beyond was achieved nowadays. Progesterone-related diabetes mellitus (PRDM) in dogs is known for its particular potential for diabetes remission. Thus, a deep understanding of the physiopathological aspects involved is crucial to postulate treatment guidelines to improve the PRDM remission rate, as well as to inform preventive measures. This narrative review aims to provide relevant detailed information on 1) canine estrus cycle and its impact on CDM etiology and management, 2) the role of pyometra as a further cause of insulin resistance, and 3) useful individual therapeutic and preventive strategies. Pharmacological annulment of progesterone effects, as well as inflammatory and progesterone-related conditions resolution in association with adequate exogenous insulin therapy, and residual beta cell function, are key aspects to achieve remission, or at least to improve diabetic clinical control. In this way, spaying should be considered mandatory in most PRDM cases. Preventive measures against CDM can include spaying recommendations; however, individual-based recommendations should be considered since castration may be associated with some long-term health issues.

Despite available global efforts and funding, Tuberculosis (TB) continues to affect a considerable number of patients worldwide. Policy makers and stakeholders set clear goals to reduce TB incidence and mortality, but the emergence of multidrug-resistant TB (MDR-TB) and extensively drug-resistant TB (XDR-TB) complicate the reach of these goals. Drug-resistance TB needs to be diagnosed rapidly and accurately to effectively treat patients, prevent the transmission of MDR-TB, minimise mortality, reduce treatment costs and avoid unnecessary hospitalisations. In this narrative review, we provide a comprehensive overview of laboratory methods for detecting drug resistance in MTB, focusing on phenotypic, molecular and other drug susceptibility testing (DST) techniques. We found a large variety of methods used, with the BACTEC MGIT 960 being the most common phenotypic DST and the Xpert MTB/RIF being the most common molecular DST. We emphasise the importance of integrating phenotypic and molecular DST to address issues like resistance to new drugs, heteroresistance, mixed infections and low-level resistance mutations. Notably, most of the analysed studies adhered to the outdated definition of XDR-TB and did not consider the pre-XDR definition, thus posing challenges in aligning diagnostic methods with the current landscape of TB resistance.

In order to enhance understanding of RNA-binding proteins in rice, a comprehensive investigation was conducted on the RRM1 gene family of rice, encompassing genome-wide identification and exploration of its role in rice blast resistance. Physical and chemical properties of the OsRRM1 gene family in rice was analyzed, including conserved domain, motif, location information, gene structure, phylogenetic tree, collinearity analysis, cis-acting elements, GO, and KEGG. Furthermore, the expression patterns of the OsRRM1 gene were examined at different time intervals following rice blast treatment. Furthermore, the alterations in expression patterns of selected OsRRM1 genes were assessed using quantitative real-time PCR(qRT-PCR). A total of 212 members of the OsRRM1 gene family were identified, which were dispersed across 12 chromosomes. Many of these genes exhibit multiple exons and introns, all of which encompass the conserved RRM1 domain and share analogous motifs. This observation suggests a high degree of conservation within the encoded sequence domain of these genes. Phylogenetic analysis revealed the existence of five subfamilies within the OsRRM1 gene family. Furthermore, the investigation of the promoter region identified homeopathic elements that are involved in nucleic acid binding and interaction with multiple transcription factors. By employing GO and KEGG analysis, four RRM1 genes were tentatively identified as crucial contributors to plant immunity, while the RRM1 gene family was also found to have a significant involvement in the complex of alternative splicing. Additionally, gene expression analysis indicated that the majority of OsRRM1 genes exhibited constitutive expression. The results of the qRT-PCR analysis revealed distinct temporal changes in the expression pattern of the OsRRM1 gene following rice blast treatment. These findings contribute to the existing knowledge of the OsRRM1 gene family, establish a foundation for further investigation into the role of the OsRRM1 gene in response to rice blast infection, and hold theoretical significance for future studies on the functionality of the OsRRM1 gene.

Nearly one third of men will incur biochemical recurrence after treatment for localized prostate cancer. Androgen deprivation therapy (ADT) is the therapeutic mainstay, however almost all patients will eventually transition to a castrate resistant state (castrate resistant prostate cancer, CRPC). Subjects with CRPC generally develop symptomatic metastatic disease (mCRPC) and incur mortality several years later. Prior to metastatic disease, men acquire non-metastatic CRPC (nmCRPC) which lends the unique opportunity for intervention to delay disease progression and symptoms. This review addresses current therapies for nmCRPC, as well as novel therapeutics and pathway strategies targeting men with nmCRPC.

In this study we evaluate performance of two American surveillance systems for monitoring the spread of antimicrobial-resistant (AMR) gonorrhea: the Gonococcal Isolate Surveillance Project (GISP) and the enhanced Gonococcal Isolate Surveillance Project (eGISP) which includes the non-urethral isolates in addition to the urethral ones utilized in the original surveillance system. A continuous-time agent-based model of gonorrhea transmission among the US men who have sex with men (MSM) population was developed and used for this purpose. Our results show that the accuracy of eGISP was nearly 10% higher than the accuracy of GISP (97.8% (95% uncertainty interval: 83.5%, 100%) vs. 87.9% (55%, 100%)). Most of time, GISP detects the moment when the resistance to the first-line antibiotic reaches the switch threshold recommended by the WHO later than when it was actually reached. This leads to the additional spread of AMR gonorrhea. We also found that including the extragenital isolates in the surveillance is more important for the accurate monitoring than increasing the number of isolates. Finally, our results demonstrate that rectum and pharynx can serve as a niche for fostering antimicrobial resistance. These findings provide a scientific basis which can be used to inform the decision made by the policymakers on how many GISP and eGISP sites to establish each year.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

The purpose of this study is to examine the match-related performance (scores and penalties) of the athletes in the Junior EJC (European Judo Championship) and U23 EJC categories before and immediately after the Covid-19 quarantine, according to gender and weight category groups. Our sample was based on the junior and U23, male and females, 2019-2020 Junior European Judo Championships and 2019-2020 U23 European Judo Championships. A total of 1431 matches in these tournaments were analyzed: male (n=812) and female (n=619). The main findings of this study showed that most matches in both the male and female categories resulted in ippon (2019-2020 average: 64,35% for Junior male, 70,55% for U23 male and 69,3% for Junior female, 64,4% for U23 female). No significant differences (p > 0.05) were observed between gender and age groups concerning the match scores. In the formation phase of the technique, considerations of high- and low-intensity actions, and analysis of the speed of athletes during matches in official competitions can help to better understand the dynamics of the variability of movements in judo matches. In addition, suggestions are presented to be applied to athletes in different age categories who are on the way to become Olympic athletes.

With the increased use of laterite nickel ore, the impact of high Al2O3 slag on blast furnace smelting has gradually increased. In this paper, the effects of slag basicity and Al2O3 content on slag viscosity and enthalpy change under constant temperature conditions was investigated. The changes in slag structure were analyzed by activation energy and Fourier Transform Infrared (FT-IR) spectroscopy. The relationship between slag components and slag temperature and viscosity when slag heat is reduced was investigated. The results showed that the viscosity first slightly decreased and then significantly increased with increasing basicity at constant temperature. With the addition of Al2O3 content, the viscosity of the slag increases. The activation energy increases with increasing slag basicity and Al2O3. With increasing basicity, the [SiO4]4- tetrahedral unit trough depth becomes shallow, the [AlO4]5- asymmetric stretching band migrates to lower wave numbers, and the slag structure depolymerizes. With the increase of Al2O3 content, the trough of [SiO4]4- tetrahedra deepens and the center of the symmetric stretching band moves to a higher wave number. The [AlO4]5- asymmetric stretching band becomes obvious, indicating the complexity of the slag structure. When the heat decreases, the slag temperature increases as the basicity increases, and the slag thermal stability is better at the basicity of 0.95-1.05. As the Al2O3 content increases, the thermal stability of the slag becomes worse.

This study demonstrates the orientation and the ‘shape factor’ have pronounced effects on the development of the localized pressure fields inside of the helmet. We used anatomically accurate headform to evaluate four modern combat helmets under blast loading conditions in the shock tube. The Advanced Combat Helmet (ACH) is used to capture the effect of the orientation on pressure under the helmet. The three modern combat helmets: ECH, Ops-Core, and Airframe, were tested in frontal orientation to determine the effect of helmet geometry. Using the unhelmeted headform data as a reference, we characterized pressure distribution inside each helmet and identified pressure focal points. The nature of these localized “hot spots” is different than the elevated pressure in the parietal region of the headform under the helmet widely recognized as the under-wash effect also observed in our tests. It is the first experimental study which indicates that the helmet presence increased the pressure experienced by the eyes (as evidenced by the pressure sensors in the H8 and H9 locations), and the forehead (denoted as H1 location). Pressure fingerprinting using an array of sensors combined with the application of principle component analysis (PCA) helped elucidate the subtle differences between helmets.

The nature of the fracture and fragmentation process of concrete medium under blast loading is the transformation process of the medium from continuum to discontinuity, coupled with the significant rate correlation of concrete medium, its mechanical behavior presents a high degree of complexity. Problems such as grid distortion and even negative volume are often encountered in the finite element method and others when solving this problem, while the material point method can effectively avoid these problems. In addition, the widely used HJC concrete constitutive model does not take into account the segmented characteristics of the calculation function for dynamic increasing factor. Therefore, in this paper, firstly, the calculation function for dynamic increasing factor in the HJC concrete model is modified by SHPB experiment, and the improved HJC concrete model is proposed; secondly, the material point method simulation program is developed, and the improved HJC concrete model is embedded into the simulation program; finally, the simulation program is verified by numerical examples, and the results show that the developed simulation program can better simulate the fracture and fragmentation process of concrete medium under blast loading, especially the pulverization characteristics of the medium in the near zone of the load.

Enterococcus faecalis is a growing cause of nosocomial and antibiotic-resistant infections. Treating drug-resistant E. faecalis requires novel approaches. The use of bacteriophages (phages) against multidrug-resistant (MDR) bacteria has recently garnered global attention. Biofilms play a vital role in E. faecalis pathogenesis as they enhance antibiotic resistance. Phages eliminate biofilms by producing lytic enzymes, including depolymerases. In this study, Enterococcus phage vB_Efs8_KEN04 (ФKEN04), isolated from a sewage treatment plant in Nairobi, Kenya, was tested against clinical strains of MDR Enterococcus faecalis. This phage had a broad host range against 100% (26/26) of MDR E. faecalis clinical isolates and cross-species activity against Enterococcus faecium. It was able to withstand acidic and alkaline conditions, from pH 3 to 11, as well as temperatures between -80ᵒC and 37ᵒC. It could inhibit and disrupt the biofilms of MDR E. faecalis. Its linear double-stranded DNA genome of 142,402 bp contains 238 coding sequences with a G+C content and coding gene density of 36.01% and 91.46%, respectively. Genomic analyses showed that ФKEN04 belongs to the genus Kochikohdavirus in the family Herelleviridae. It lacked antimicrobial resistance, virulence, and lysogeny genes, and its stability, broad host range, and cross-species lysis indicate strong potential for the treatment of Enterococcus infections.

Shigella and Salmonella have been implicated in neonatal sepsis, food poisoning, and bacteremia. Their increasing resistance to antibiotics has undermined treatment options, constituting a public health crisis. Also, the scarcity of new antibiotics in the development pipeline compounds multidrug-resistance (MDR). Hence, there is a need to potentiate antibiotics to mitigate resistance. This study leveraged riboflavin to re-sensitize fluoroquinolones and carbapenems against MDR Shigella and Salmonella spp. Disk diffusion, microbroth-dilution, chequerboard, and time-kill assays were used to determine resistance profiles and riboflavin-antibiotic activity. Biofilm-formation and bacterial viability (after riboflavin-antibiotic challenge) was determined with crystal-violet and Macrophage infection assays, respectively. Strains exhibited >80% resistance to fluoroquinolones and carbapenems, with 160–320 µg MIC ranges and 0.5–2 FIC, indicating no synergy. At 40–80 µg riboflavin, there was two-fold reduction in bacterial survival, with meropenem-riboflavin exhibiting significant reduction and FIC of 0.075 indicating high synergistic activity. Biofilm-formation was altered (from strong to weak phenotype) with 40 µg riboflavin-antibiotic treatment. There was a 40–70% reduction in bacterial survival in THP-1 cells treated with meropenem-riboflavin after 3 hours, and complete clearance between 24-48 hpi. Riboflavin potentiated fluoroquinolones and meropenem, leading to modulation of the host immune response for the clearance of the strains.

Background/objectives: The health benefits of resistant starch are well known, but there have not been many studies available documenting the effect of basmati rice products containg resistant starch upon blood glucose level and lipid profile in vivo efficacy. Methods: Common cooking methods were used to prepare basmati rice products including two boiling methods viz. boiling 1 (boiling by absorption), boiling 2 (boiling in extra amount of water), frying and pressure cooking. The cooked rice were held at various temperatures and times: it was made fresh (T1), kept at room temperature (20–22°C) for 24 h (T2), kept at 4°C for 24 h (T3), and then reheated after being kept at 4°C for 24 h(T4). Next, the products' proximate composition, total dietary fibre (soluble and insoluble), resistant starch (RS), and In vitro starch digestion rate (rapidly and slowly digested starch) were examined. The effect of RS on blood glucose and lipid profile were measured in humans and rats. Histopathological study of liver and pancreas in rats were also observed. Results: The basmati rice prepared by boiling 1 and stored with T3 was found more effective to control blood glucose and lipid profile. Similarly in rats, the blood glucose level, cholesterol, triglycerides and LDL were reduced about 29.7, 37.9, 31.3 and 30.5% respectively, after consumption of basmsti rice prepared by boiling 1 and stored at T3. Conclusion: Rice products stored at 4⁰C have a high amount of resistant starh, insoluble dietary fibre, slowly digestible starch and low glycemic index. Thus helps to inhibit glycogen and lipid synthesis.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Rice blast is the most harmful disease caused by Magnaporthe oryzae, leading to yield loss. The aim of the work is to improve resistance of rice to blast by introducing and pyramiding genes using conventional breeding technique and modern MAS analysis. Pyramiding is the combination of several resistance genes in one genotype, in this case it improves the resistance of rice to pathogens. MAS analysis revealed that 3 out of 4 studied domestic high-yielding rice cultivars (Bakanasski, Aisaule and Aru) contain 1 blast resistance gene (Pi-2). It was discovered 7 pyramidal lines with the introduction of a combination of 2 blast resistance genes (Pi-1 and Pi-ta) into 6 hybrids and 3 genes (Pi-1, Pi-33 and Pi-ta) into 1 line. Phytopathological test of local cultivars and pyramidal lines of rice showed that 3 out of 7 pyramidal lines have moderate resistance: 2 lines (F2 Bakanasski/7667 (var. vulgaris Koern.) and F2 Aisaule/7664 (var. italica Alef.)), containing 2 resistance genes (Pi-1 and Pi-ta) and 1 line – F2 Aisaule/7689 (var. zeravschanica Brsch.), carrying 3 genes (Pi-1, Pi-33 and Pi-ta), while the local cultivars Bakanasski, Aisaule and Aru are susceptible. As a result, the blast resistance of rice was improved by creating pyramidal lines. Pyramided lines can be used for germplasm exchange and in rice breeding programs to improve blast resistance in rice.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

A lead zirconate titanate [PZT;Pb(Zr_0.52Ti_0.48)O₃] layer embedded infrared (IR) detector decorated with wavelength-selective plasmonic crystals has been investigated for high-performance non-dispersive infrared (NDIR) spectroscopy. A plasmonic IR detector with an enhanced IR absorption band has been designed based on numerical simulations, fabricated by conventional microfabrication techniques, and characterized with a broadly tunable quantum cascade laser. The enhanced responsivity of the plasmonic IR detector at specific wavelength band has improved the performance of NDIR spectroscopy and pushed the limit of detection (LOD) by an order of magnitude. In this paper, a 13 fold enhancement in the LOD of a methane gas sensing using NDIR spectroscopy is demonstrated with the plasmonic IR detector.

Precise individual tree or sample-based inventories derived from 3D point cloud data of mobile laser scanning can improve our comprehensive understanding of the structure, function, resilience, biodiversity, and ecosystem services of urban forests. This study assessed the performance of a hand-held laser scanning system for the extraction of tree position, diameter at breast height (DBH) and tree height (H) in an urban area. A total of 2083 trees of 13 species from 34 plots were analyzed. The results showed that the registration of tree positions using ground control points (GCPs) demonstrated high accuracy, with errors consistently below 0.4 m, except for a few instances. The extraction accuracy of DBH for all trees and individual species remained consistently high, with a total root mean square error (RMSE) of 2.06 cm (6.89%) and a bias of 0.62 cm (2.07%). Notably, broad-leaved trees outperformed coniferous trees, with RMSE and bias values of 1.86 cm (6%) and 0.76 cm (2.46%) compared to 2.54 cm (9.46%) and 0.23 cm (0.84%). Tree height extraction accuracy varied significantly among different species, with R2 values ranging from 0.65 to 0.92. Generally, both DBH and height were underestimated. Linear mixed effects models (LME) were applied to evaluate factors affecting the performance of HLS with the plot as a random factor. LME analysis revealed that plant type and terrain significantly influenced the accuracy of DBH and H derived from HLS data. Other fixed factors of plot area, tree density and trajectory length didn’t have significance. With a large sample size, we concluded that the HLS demonstrated sufficient accuracy in extracting individual tree parameters in urban forests.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

Process safety plays a vital role in the modern process industry. To prevent undesired accidents caused by malfunctions or other disturbances in complex industrial processes, considerable attention has been paid to data-driven fault detection techniques. To explore the underlying manifold structure, manifold learning methods including Laplacian eigenmaps, locally linear embedding, and Hessian eigenmaps have been utilized in data-driven fault detection. However, only the partial local structure information is extracted from the aforementioned methods. In this paper, these typical manifold learning methods are synthesized to find the underlying manifold structure from different angles. A more comprehensive local structure is discovered under a unified framework by constructing an objection optimization function for dimension reduction of the process data. The proposed method takes advantage of different manifold learning methods. Based on the proposed dimension reduction method, a new data-driven fault detection method is developed. Hotelling’s T2 and Q statistics are established for the purpose of fault detection. Experiments on an industrial benchmark Tennessee Eastman process and a real blast furnace ironmaking process are carried out to demonstrate the superiority and effectiveness of the proposed method.

Concrete-filled steel columns have been extensively used in the world due to having all suitable characteristics of concrete and steel, more ductility, increasing concrete confinement using steel wall, large energy-absorption capacity and appropriate fire behavior. In present paper, concrete-filled steel square columns have been simulated under the influence of blast load using ABAQUS software. These responses will be compared for scaled distances based on the distance to source and weight of explosive material. As result, it can be seen that although concrete deformation has been restricted using steel tube, but inner layer of concrete has been seriously damaged and column displacement will be decreased by increasing scaled distance. We also concluded that concrete-filled steel columns have high ductility and blast resistance.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Understanding the dynamics of teamwork and communication among healthcare professionals is crucial in the face of evolving healthcare challenges. This study assessed relational coordination among healthcare professionals in the South Tyrolean healthcare system in Italy, focusing on communication and teamwork dynamics in a cross-sectional survey. Using the validated Relational Coordination Survey (RCS) instrument and 525 completed online responses, the questionnaire aimed to understand the implications of different levels of relational coordination ratings by general practitioners, hospital physicians, nurses, and administrative personnel (response rate 26%). The demographics of the participants revealed a predominance of female professionals (64%), with an average age of 50 and 18 years of service. The resulting RCS scores varied significantly across professional groups, with nurses reporting the highest within-group scores, indicating moderate coordination, and administrators reporting the lowest scores, reflecting areas of weak coordination. Between-group relational coordination was generally perceived as weak across professional groups, with the least weakness observed between general practitioners and nurses. German or Italian language and health district affiliation emerged as significant factors influencing relational coordination ratings, highlighting the need for differentiated understanding and strategies in multilingual and diverse regional settings. Assessments of interdisciplinary feedback and referral practices highlight the variation in teamwork and communication weaknesses and underscore the need for targeted interventions to improve relational coordination. This study provides insights into the complexity of relational dynamics in health care settings. It suggests that improving relational coordination through tailored strategies could significantly improve team effectiveness, quality of patient care, and overall system efficiency.

Obsessive–compulsive disorder (OCD) is believed to follow a waxing and waning course, often according to environmental stressors. During the COVID-19 pandemic, pre-existing OCD symptoms were reported to increase and to change from checking to washing behaviors, while new-onset symptoms were predominantly of the hoarding type. In the present study, we followed the evolution of OCD symptoms, anxiety, depression, and insight of illness in forty-six OCD patients throughout the pandemic. Clinical measures were collected at four different time points before and during the COVID-19 pandemic in Italy. Within-subject comparisons were used to compare clinical scale scores across time, and correlations were examined between patients' baseline characteristics and changes in clinical scores. We found that all clinical measures increased during the first Italian lockdown, with respect to the pre-pandemic values. Anxiety decreased during the temporary elimination of restriction provisions, whereas severity of OCD symptoms and insight returned to pre-pandemic values during the second mandatory lockdown. These results were observed only in two sub-groups of patients: those taking benzodiazepines and those with shorter illness duration. Our findings suggest the need of additional clinical attention to these specific sub-groups of OCD patients in case of particularly distressing circumstances, while pointing to a possible adaptive role of their OCD symptoms when the environment requires a higher care of hygiene and extraordinary supply of essential resources.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

The aim of the present trial was to evaluate the growth performance of buffalo calves fed diets characterized by different forage/concentrate ratio with or without the Saccharomyces Cerevisiae supplementation (CBS 493.94, Yea-Sacc®). Twenty-four male buffalo calves (mean age 145.1 ± 16.1 days; mean weight 108.0 ± 18.7) were assigned randomly to 4 groups, homogeneous for age, fed four different diets: diet 1 F:C ratio 50:50; diet 2 F:C ratio 30:70; diet 3 F:C ratio 50:50 + Yea-Sacc® and diet 4 F:C ratio 30:70 + Yea-Sacc®. Buffalo calves were individually weighted before the start of the experiment and the data were used as a covariate, monthly until the end of the trial. Dry matter intake (DMI), daily weight gain (DWG) and feed conversion ratio (FCR) were calculated. The differences in diets’ composition significantly (p

The performance of the presurgical test (preSurg) for temporal lobe epilepsy (TLE) was evaluated via video-electroencephalography (VEEG), electroencephalography (EEG), 99mTc-HmPAO single-photon emission tomography (SPECT) and 1.5 T magnetic resonance imaging (MRI) in a group of 112 men (37.0 ± 1.1 years) and 106 women (39.7 ± 1.1 years) operated on for TLE. The epileptic zone (EZ) was adequately identified to determine whether the patient reached an Engel I grade (EI) at least one year postop. Accuracy was evaluated by the coefficient α, ranging from 3 (when result = EZ) to 2 (result in the same hemisphere as the EZ), 1 (noninformative result) or 0 (EZ in the contralateral hemisphere). The simplicity of diagnosis was defined as the number of preSurg surgeries needed to identify the EZ. EI was obtained in 85.8% of patients even though 42.2% of patients had noninformative MRI results. For preSurg α was (mean ± SEM) = VEEG (2.83 ± 0.04) > MRI (2.14 ± 0.08) > EEG (1.87 ± 0.09) > SPECT (1.71 ± 0.09). The accuracy (combination of sensitivity and specificity) was calculated as follows: VEEG (0.797) > MRI (0.518) > EEG (0.446) > SPECT (0.360). The likelihood positive ratio was greater, and the likelihood negative ratio was lower for VEEG. The most relevant factor for the regression model was VEEG (3.106) > MRI (2.558) > EEG (1.905), and the factors were not significantly related to SPECT. EZs in EI patients with low simplicity were identified mainly by VEEG. A very good postoperative outcome can be obtained even in TLE patients with no lesions on MRI. The VEEG is the most reliable preSurg test and may be the only reliable test for patients with very low simplicity (i.e., difficult).single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

In rock blasting for mining production, stress waves play a major role in rock fracturing along with explosion gases. Better energy distribution improves fragmentation and safety, lowers production costs, increases productivity, and controls ore losses and dilution. Blast outcomes vary significantly with the choice of the explosive and the properties of the rock mass encountered. This study analyzes the effects of rock mass and explosives properties on the blast outcomes through numerical simulation using data from the case study and later validates the simulation results from the field blast fragmentation. The outcomes suggest that, for a given set of rock properties, the choice of explosive has a major influence on the resulting fragmentation. Strong explosives favor large fracture extents in hard rocks, while less strong explosives offer a better distribution of explosive energy and fractures. The presence of rock structures such as rock con-tacts and joints influences the propagation of stress waves and fractures depending on the structures' material properties, intensity and orientations, and the direction and strength of the stress wave. To achieve effective fragmentation, the blast design should mitigate the effect of variability in the rock mass by ensuring adequate energy distribution within the limits of geo-metrical design.

Plant diseases are among the major factors affecting plant productivity. Biological control of plant diseases is preferred over chemical control as it is environment-friendly, cost-effective, and sustainable. Among many microbes capable of providing biological control of plant diseases, probiotic Bacillus species are most promising as they can survive in adverse conditions, provide plants with a wide range of benefits including protection from phytopathogens. Wheat blast caused by Magnaporthe oryzae Triticum pathotype (MoT) has emerged as a potential threat to global wheat production. Due to unreliability of fungicides and limited cultivar resistance, we aimed to screen and identify potential antagonist bacteria collected from internal tissues of rice and wheat seeds to determine their in vitro and in vivo inhibitory effects against MoT. Dual culture and seedling assays were performed to evaluate the efficacy of probiotic bacteria. Out of 170 bacterial isolates, three bacteria (BTS-3, BTS-4, and BTLK6A) were screened as potential antagonists against MoT in vitro. Artificial inoculation at the seedling stage showed that the isolates BTS-4, BTS–3, and BTLK6A reduced 89, 88, and 85% of wheat blast disease severity, respectively, compared to mock-inoculated control. The bacterial isolates were identified as Bacillus subtilis (BTS-3) and B. velezensis (BTS-4 and BTLK6A) through genome phylogeny. The whole genome sequence of these three bacterial strains decoded a number of orthologs to intrinsic genes of antimicrobial peptides, antioxidant defense enzymes, cell wall degrading enzymes, compounds involved in the induction of systemic resistance (ISR) in host plants, and volatile compounds to make them promising biologicals to control MoT in wheat. Combined data of in vitro and in vivo along with genome analysis suggest that Bacillus spp. suppress the destructive wheat blast disease likely through antibiosis and ISR in the host plants. Further field evaluation and characterization of antimicrobial compounds are needed for a better understanding of the mode of action and practical recommendation of these bacteria for wheat blast control in the farmers’ fields.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

The main purpose of the study was to study the effects of a specific rowing ergometer training program on the athletic performance of young adolescents (n=56; 11.73 ± 1.4 years old) com-pared to a workout based on general strength training. Eight-week training program was im-plemented, with four sessions per week and two-hours per session. Sample was divided in two groups: a control group (CG) that performed circuit training with exercises aimed at building general strength and an experimental group (EG) who focused on specifically training on a rowing ergometer (rowing machine). The data obtained in a rowing meter test over the compe-tition distance were analyzed to obtain the average power attained (W) at the beginning of the training, at the middle (4 weeks), at the end of the training (8 weeks) and one year after the ex-perimentation. The results show that, although both forms of training improve the average W obtained in both categories, the EG subjects (+29.94W) obtained better averages in all phases of the study compared to the CG (+5.88W). Furthermore, this increase was greater in male rowers (+ 34.06W) than in female rowers (+24.54W). These results reveal that a specific rower rowing ergometer training program has a significant effect than a general strength program and these effects can even be observed a year after the intervention.

Logistics plays an important role in globalized companies and contributes to the development of foreign trade. A large number of external conditions, such as recession and inflation, affect logistics. Therefore, managers should find ways to improve operational performance, enabling them to increase efficiency while considering environmental sustainability due to the industry’s large scale of energy consumption. Based on data collected from the financial reports of top global logistics companies, this study uses a DEA model to calculate corporate efficiency by implementing a Grey forecasting approach to forecast future sustainability values. Consequently, the study addresses the problem of how to enhance operational performance while accounting for the impact of external conditions. This research can help logistics companies develop operation strategies in the future that will enhance their competitiveness vis-à-vis rivals in a time of global economic volatility.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

Blast charge initiation procedures have a significant impact on both mining safety and production rates. In this study, the inventory benefit of an electric initiation system was investigated to assess its influence on both fragmentation and blast-induced damages. The Wipfrag software's was used to examine the size distribution and productivity of 12 small-scale blasts initiated by both non-electric and electric detonators. All blast rounds was initiated with plain type of electric and NONEL detonators. The average burden, spacing, stemming length, and charge weight were, respectively, 0.85 m, 1.10 m, 0.66m, and 1.1kg. The results showed that the mesh through which 80% of the blast fragments will pass for the electric blast is smaller than the mesh through which the material products from the NONEL blast will pass. The results also demonstrate that the generated blast-induced ground vibration (PPV) from all blast rounds for electric blast varies from 0.4–1.2 mm/s and 80–105dB, while that for non-electric blast ranges from 0.05–0.2mm/s and 72–95dB. As a result, the electric blast initiation technique was found to produce good fragmentation, with a higher percentage of optimum fragment sizes on spec than non-electrically initiated blasts.

This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Application of chemical pesticides to protect agricultural crops from pests and diseases is discouraged due to their harmful effects on human and environment. Therefore, alternative approaches for crop pro-tection through microbial or microbe originated pesticides have been gaining momentum. Wheat blast is a destructive fungal disease caused by Magnaporthe oryzae Triticum (MoT) pathotype, which poses a seri-ous threat to global food security. Screening of secondary metabolites against MoT revealed that antimy-cin A isolated from a marine Streptomyces sp. had significant inhibitory effect on mycelial growth in vitro. This study aimed to investigate the inhibitory effects of antimycin A on some critical life stages of MoT and evaluate the efficacy of wheat blast disease control by this natural product. Bioassay indicated that antimycin A suppressed mycelial growth, conidiogenesis, germination of conidia and formation of ap-pressoria in germinated conidia of MoT in a dose-dependent manner with minimum inhibitory concen-tration 0.005 μg/disk. If germinated, antimycin A induced abnormal germ tubes (4.8%) and suppressed the formation of appressoria. Interestingly, application of antimycin A significantly suppressed wheat blast disease in both seedling and heading stages of wheat supporting the results from invitro study. This is the first report on inhibition of mycelial growth, conidiogenesis, conidia germination, detrimental morphological alterations in germinated conidia, and suppression of wheat blast disease caused by a Triticum pathotype of M. Oryzae. Further study is required to unravel the precise mode of action of this promising natural compound for considering it as a biopesticide to combat wheat blast.

The $k$-means problem is to compute a set of $k$ centers (points) that minimizes the sum of squared distances to a given set of $n$ points in a metric space. Arguably, the most common algorithm to solve it is $k$-means++ which is easy to implement, and provides a provably small approximation factor in time that is linear in $n$. We generalize $k$-means++ to support: (i) non-metric spaces and any pseudo-distance function. In particular, it supports M-estimators functions that handle outliers, e.g. where the distance $\mathrm{dist}(p,x)$ between a pair of points is replaced by $\min {\mathrm{dist}(p,x),1}$. (ii) $k$-means clustering with $m\geq 1$ outliers, i.e., where the $m$ farthest points from the $k$ centers are excluded from the total sum of distances. This is the first algorithm whose running time is linear in $n$ and polynomial in $k$ and $m$.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Capital structure decision plays an imperative role in firm’s performance. Recognizing the importance, there has been many studies inspected the rapport of capital structure with performance of firms and findings of those studies are inconclusive. In addition, there is relative deficiency of empirical studies examining the link of capital structure with performance of banks in Bangladesh. This paper attempted to fill this gap. Using panel data of 22 banks for the period of 2005-2014, this study empirically examined the impacts of capital structure on the performance of Bangladeshi banks assessed by return on equity, return on assets and earnings per share. Results from pooled ordinary least square analysis show that there are inverse impacts of capital structure on bank’s performance. Empirical findings of this study is of greater significance for the developing countries like Bangladesh because it will call upon concentration of the bank management and policy makers to pursue such policies to reduce reliance on debt and to accomplish optimal level capital structure. This research also contributes to empirical literatures by reconfirming (or otherwise) findings of previous studies.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

Despite the recognized influence of maximum or acceleration strength on combat techniques and countermovement jump (CMJ) performance, the relationship between body segment weights and combat techniques remains unexplored. This study aimed to examine the impact of body segment weights, including striking arm weight (SAW), kicking leg weight (KLW), and trunk weight (TW), on the dynamics of direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and CMJ performance. Sixteen male military cadets (22.3±1.8 years, 181.4±7.0 cm, 83.0±8.1 kg) performed combat techniques, with performance measured by using a force plate and body segment weights assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis was applied. Results indicated a strong correlation between KLW and FK impulse (r = 0.64, p ≤ 0.01) and CMJ impact force (r = 0.80, p ≤ 0.01). SAW showed moderate correlations with DP impulse (r = 0.53, p ≤ 0.05) and ES impulse (r = 0.54, p ≤ 0.05). Additionally, FK peak and impact forces were strongly correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01), and FK peak force moderately correlated with CMJ peak velocity (r = 0.63, p ≤ 0.05). These findings suggest targeted arm strength training could enhance striking abilities, while improvements in leg acceleration strength may directly boost kicking performance and vertical jump capabilities, which are crucial in combat scenarios.

The prospects of processing blast furnace and steelmaking sludge using Waelz process in a laboratory rotary kiln is shown. The influence of varying thermal treatment modes, furnace atmosphere and type of reducing agents on the level of zinc reduction from sludges was analyzed. In general, the blast furnace sludge contains a high portion of iron (approx.48 wt. %) and can be reused as a charge after satisfactory zinc reduction. It was found that N- atmosphere and high content of the graphite or coke oven reducing agent in combination with high temperature can reduce the content of Zn in the sludge to 0.08 wt. % at 1200 °C for mixture of steelmaking and blast furnace sludge. A significant reduction in the Zn content to 0.66 wt. % occurs at 1100 °C. The content and type of reducing agent play an important role; graphite has shown a better reducing ability compared to coke oven dust. When nitrogen is used, zinc is reduced even without an additional reducing agent, since the carbon contained in the sludge is made use of for the reduction. In an air atmosphere, without the use of a reducing agent, there was no reduction in the Zn content.

Plant pathogens utilize effectors to subvert host cell biology for facilitating infection. However certain effectors, called as the avirulence proteins, trigger immune responses in the host. AvrPi54 is an avirulence protein from fungus Magnaporthe oryzae which induces the defense reactions in rice cells that contain Pi54 resistance gene. The characterization of such proteins and elucidation of their function facilitate the understanding of the mechanism of disease establishment. In present study, physiochemical properties of AvrPi54 were analysed using computational methods. We found that mature AvrPi54 is a small, hydrophobic and secretary protein with 134 amino acids. It is rich in small amino acids with no significant homology with other proteins in databases. The gene ORF was cloned in pET28a(+) vector and expressed in E. coli BL21(DE3)pLysS. The protein was purified using affinity chromatography. Transient expression of the gene in epidermal cells of onion bulb is a powerful tool to predict the subcellular localization in plant cells. We fused AvrPi54 to eYFP and transformed epidermal cell layer of onion bulb. Fused protein localized to the plasma membrane and nucleus of plant cells. Therefore, AvrPi54 might be functioning in the host cell as transcription factor or chromatin remodelling factor to modify pathogenesis-related processes.

Emerging autologous cellular therapies that utilize platelet-rich plasma (PRP) applications have the potential to play adjunctive roles in a variety of regenerative medicine treatment plans. There is a global unmet need for tissue repair strategies to treat musculoskeletal (MSK) and spinal disorders, osteoarthritis (OA), and patients with chronic complex and recalcitrant wounds. PRP therapy is based on the fact that platelet growth factors (PGFs) support the three phases of wound healing and repair cascade (inflammation, proliferation, remodeling). Many different PRP formulations have been evaluated, originating from human, in vitro, and animal studies. However, recommendations from in vitro and animal research often lead to different clinical outcomes because it is difficult to translate non-clinical study outcomes and methodology recommendations to human clinical treatment protocols. In recent years, progress has been made in understanding PRP technology and the concepts for bioformulation, and new research directives and new indications have been suggested. In this review, we will discuss recent developments regarding PRP preparation and composition regarding platelet dosing, leukocyte activities concerning innate and adaptive immunomodulation, serotonin (5-HT) effects and pain killing. Furthermore, we discuss PRP mechanisms related to inflammation and angiogenesis in tissue repair and regenerative processes. Lastly, we will review the effect of certain drugs on PRP activity, and the combination of PRP and rehabilitation protocols.

Classical Arabic poetry is a form of Arabic literature, and almost every piece of Arabic poetry follows one of the 16 meters. The rhythmic framework of the poems or the verses is called meters. The deep learning (DL) model was implemented using TensorFlow in this work using a large dataset of Arabic poetry. The character level encoding was used to convert text to integers for classifying the full-verse and half-verse data. The study evaluates the data without removing diacritics from the text. The train-test-split method with a 70-15-15 split was employed for classification. 15% of the total data was considered unseen test data for all models. The work was conducted with multiple deep learning models, including the Long Short-Term Memory (LSTM), Gated Recurrent Units (GRU), and Bidirectional LSTM (Bi-LSTM). The Bi-LSTM model shows the best accuracy of all the models specified, with 97.53% for full-verse and 95.23% for half-verse without removing diacritic data.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

Candida glabrata is a yeast of increasing medical relevance, particularly in critically ill patients. It is the second most isolated Candida species associated with invasive candidiasis (IC) behind C. albicans. The attributed higher incidence is primarily due to an increase in the acquired immunodeficiency syndrome (AIDS) population, cancer, and diabetes patients. The elderly population and the frequent use of indwelling medical devices are also predisposing factors. The work aimed to review various virulence factors that facilitate the survival of pathogenic C. glabrata in IC. The available published research articles related to the pathogenicity of C. glabrata were retrieved and reviewed from four credible databases, mainly Google Scholar, ScienceDirect, PubMed, and Scopus. The articles highlighted many virulence factors associated with pathogenicity in C. glabrata, including adherence to a susceptible host surface, evading host defences, and producing hydrolytic enzymes (e.g., phospholipases, proteases, and haemolysins). The factors facilitate infection initiation. Other virulent factors include iron regulation and genetic mutations. Accordingly, biofilm production, tolerance to high-stress environments, and development of resistance to the antifungal drug, notably to fluconazole and other azole derivatives, were reported. The review provided evident pathogenic mechanisms and antifungal resistance associated with C. glabrata in ensuring its sustenance and survival.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

Conobea scoparioides (Plantaginaceae) is an herbaceous plant known as "pataqueira" that grows wild in seasonally wet areas of the Amazon region. It is used for aromatic baths and anti-protozoan remedies by the Brazilian Amazon native people. The main volatile compounds identified in the essential oil of "Pataqueira" were the phenolic monoterpenes thymol and thymol methyl ether and their precursors, the monoterpene hydrocarbons α-phellandrene and p-cymene. A hydrotalcite synthesized from blast-furnace slag exhibited a 3:2 (Mg/Al) molar ratio, and this layered double hydroxide (LDH) was evaluated as a catalyst in converting the main monoterpenes of the "Pataqueira" oil. This action significantly increased thymol content, from 41% to 95%, associated with the percentual reduction of other main components, such as thymol methyl ether, α-phellandrene, and p-cymene. The LDH reaction showed a strong tendency towards producing hydroxylated derivatives, and its behavior was similar to the hypothetical plant biosynthetic pathway, which leads to the production of the monoterpenes of "Pataqueira" oil. Thymol and its derivatives are potent antiseptics applied in pharmaceutical and hygienic products as antibacterial, antifungal, and antioxidant properties, among others. The present work reports a natural source with a high thymol content in aromatic plants from the Amazon, with evident economic value.

Abstract: Chloroplast is a new hotspot in the field of plant transformation system of plant genetic engineering. Initially developed in Chlamydomonas and tobacco, it is now feasible in a broad range of species. They exploit the homologous recombination and segregation pathways acting on chloroplast genomes and are based on direct repeats, transient co-integration or co-transformation and segregation of trait and marker genes. Foreign site-specific recombinases and their target sites provide an alternative and effective method for removing marker genes from plastids.Chloroplast genetic engineering has many advantages over nuclear genetic enginering, especially site-specific introduction of foreign genes ,leading to the absence of gene siliency and positon effect,which providing the available to explore the regulation and mechanism of chloroplast genes`expression in vitro .It also can identify the structure and function of the chloroplast genome , the expression of chloroplast affect the nulear genome. In this paper, the basic methodology of chloroplast transformation, the current techniques and applications, and the future possibilities for Chloroplast genetic engineering was reviewed[1-3].

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

In Chronic Myeloid Leukemia (CML) patients, CD34+/CD38-/CD26+ cell population represents a “CML specific” Leukemia Stem Cell (LSC) compartment. Indeed, preliminary studies showed that the expression of CD26 discriminates bone marrow CML Leukemic Stem Cells (LSCs) from nor-mal Hematopoietic Stem Cells (HSCs) or from LSCs of other myeloid neoplasms. We were first to demonstrate that at diagnosis CD34+/CD38-/CD26+ cells are easily measurable also in Peripheral Blood (PB) and that residual circulating CD26+LSCs persist, with a fluctuating trend, in most pa-tients in optimal response during treatment with Tyrosine Kinase Inhibitors (TKIs) and even after successful TKI discontinuation. These data corroborate and confirm the possibility of using flow-cytometry CD26+ evaluation as an important diagnostic tool that, combined with molecular biology and cytogenetic, could provide a rapid diagnosis of Chronic Phase (CP) CML starting from a simple PB sample. Yet, few data are available regarding the behavior of CD26+LSCs during Accelerated Phase (AP) or Blast Phase (BP) CML and the role, if any, this peculiar staminal cell compartment may play in disease progression. In the present study we compared the presence and phenotypic characteristics of circulating CD26+LSCs in CP CML patients at diagnosis, during AP and in cases of progression to lymphoid BP, inquiring a possible role of these cells during dis-ease evolution.

CO2 emissions resulting from the production of cement is a major issue, but can be limited by the partial substitution of cement by low-carbon-impact additions. The aim of this study was the formulation of a ternary binder based on ordinary Portland cement (OPC), ground granulated blast-furnace slag (GGBS) and flash-calcined sediment (FCS), a dredged waste which was valorized after applying a new heat treatment: flash calcination. The used materials were physically, chemically and mineralogically characterized. The composition of the formulations was optimized using mixture designs. Five formulations, one reference formulation RM (100% OPC), one binary formulation (50% OPC/50% GGBS), and three ternary formulations with a variable FCS rate (10%, 15%, 20%), were selected and characterized fresh and hardened. Results showed that the incorporation of FCS reduced the workability and increased the density. In addition, a decrease in the initial setting time and the heat of hydration peak were observed. In the hardened state, the formulation containing 10% FCS showed 90-day mechanical strengths superior to that of RM. The use of FCS in ternary binders could reduce the environmental impact by reducing greenhouse gas emissions.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

Multidrug resistant extended-spectrum β-lactamase (ESBL)-producing Escherichia coli is considered a serious concern to public health worldwide including Bangladesh, and chicken meat is recognized as an important reservoir of ESBL-Ec dissemination to humans. Therefore, this study aimed to determine the prevalence, and phenotypic and genotypic antimicrobial resistance pattern of ESBL-producing Escherichia coli (ESBL-Ec) in frozen chicken meat. A total of 113 frozen chicken meat samples were purchased from 40 outlets of 9 branded supershops in five megacities in Bangladesh. Isolation and identification of Escherichia coli were done based on cultural, biochemical properties and PCR assay. The resistance pattern was determined by disk diffusion method. ESBL-encoding genes were determined by multiplex PCR. The results showed that 76.1% samples were positive for Escherichia coli, of which 86% were ESBL producers. All the isolates were multidrug-resistant (MDR). Resistance to 9–11 and 12–13 antimicrobial classes was observed in 38.4% and 17.4% isolates, respectively while only 11.6% were resistant to 3–5 classes. The possible extensively drug resistance (pXDR) was found in 2.3% isolates. The high single resistance was observed for oxytetracycline (93%) and amoxicillin (91.9%), followed by ampicillin (89.5%), trimethoprim-sulphamethoxazole and pefloxacin (88.4%), and tetracycline (84.9%). Most importantly, 89.6% of isolates were resistant to carbapenems. All the isolates were positive for blaTEM gene. However, the blaSHV and blaCTX-M-2 genes were identified in two ESBL-non producer isolates. None of the isolates were carried blaCTX-M-1 gene. This study provided evidence of wide dissemination of MDR and existence of pXDR ESBL-Ec in frozen chicken meat in Bangladesh. Our data clearly indicated that frozen chicken meat is, at the present time, the most significant known food source of ESBL-Ec to which peoples are regularly exposed.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Injuries from exposure to blasts are of significant concern in military operational settings, including tactical training, and is associated with self-reported concussion-like symptomology and physiological changes as increased intestinal permeability (IP) investigated herein. Timeseries gene expression and IP biomarker data were generated from “breachers” exposed to controlled, low-level explosive blast during training. Samples from 30 male participants at pre, post, follow-up blast exposure the next day were assayed via RNA-seq and ELISA. A battery of symptom data was also collected at each of these time points that acutely showed elevated symptom reporting related to headache, concentration, dizziness, and slowed thinking, dissipating ~16hrs following blast exposure. Evidence for bacterial translocation into circulation following blast exposure was detected by significant stepwise increase in microbial diversity (measured via alpha-diversity p=0.049). Alterations in levels of IP protein biomarkers (i.e., Zonulin, LBP, Claudin-3, I-FABP) assessed in a subset of these participants (n=23) further evidenced blast exposure associates with IP. The observed symptom profile was consistent with mTBI and was further associated with changes in bacterial translocation and intestinal permeability, suggesting that IP may be linked to a decrease in cognitive performance. These preliminary findings show for the first

Antimicrobial resistance (AMR) is a major global concern; antibiotics and other regular treatment methods have failed to overcome the increasing number of infectious diseases. Bacteriophages (phages) are viruses that specifically target/ kill bacterial hosts without affecting other human microbiome. Phage therapy provides optimism in the current global healthcare scenario with a long history of its applications in humans that has now reached various clinical trials. Phages in clinical trials have specific requirements of being exclusively lytic, free from toxic genes with an enhanced host range that adds an advantage to this requisite. This review explains in detail the various phage engineering methods and their potential applications in therapy. To make phages more efficient, engineering has been attempted using techniques like conventional homologous recombination, Bacteriophage Recombineering of Electroporated DNA (BRED), clustered regularly interspaced short palindromic repeats (CRISPR)-Cas, CRISPY-BRED/Bacteriophage Recombineering with Infectious Particles (BRIP), chemically accelerated viral evolution (CAVE), and phage genome rebooting. Phages are administered in cocktail form in combination with antibiotics, vaccines, and purified proteins, such as endolysins. Thus, phage therapy is proving to be a better alternative for treating life-threatening infections, with more specificity and fewer detrimental consequences.

With the increasing use of genome sequencing as a surveillance tool for molecular epidemiology of antimicrobial resistance (AMR), databases and clear nomenclature for AMR gene families are critical. Due to the convoluted nomenclatural history of the integron-associated trimethoprim-resistant dihydrofolatereductase (dfr) gene family, we decided to conduct a literature review, comparative sequence analysis, and phylogenetic investigation of the dfr family, the results of which are presented here and available at the Comprehensive Antibiotic Resistance Database (CARD). Overall, literature review and phylogenetic analysis resolved gene name synonyms based on sequence. We recommend adoption of phylogenetic methods to help guide AMR gene naming efforts and relegation of misleading names to synonyms.

Beetles are by far one of the most successful and diverse insect species. A part of this success is attributed to their elytra which provide various functions such as protection to their bodies from mechanical forces and the harmful environmental factors. In this study, Stag beetle (Lucanus cervus) elytra were first examined for their overall flexural properties and were observed to have a localized shape retaining snap-through mechanism which could play a crucial role in energy absorption, e.g. during battles and falls from heights. The snap-through mechanism was validated using theoretical calculations and also finite element simulations. Elytra were also characterized to examine their puncture and wear resistance. Our results show that elytra resisted puncture up to a force of 1.8±0.4 N and have puncture resistance compared to that of commercially available puncture resistant gloves. The measured values of modulus and hardness of elytra exocuticle were 10.3±0.8 GPa and 0.7±0.1 GPa. Using the hardness to modulus ratio as an indicator of wear resistance, the estimated value was observed to be in the range of wear resistant biological materials. Thus, our study demonstrates different mechanical properties of the stag beetle elytra which can be explored to design shape retaining bio-inspired composites with enhanced puncture and wear resistance.

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.