This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

The objective of this study is to determine the relationship between body condition score (BCS) and body carcass fat (BCF) of ewes at two key stages of the production cycle. Data were collected from 88 Coopworth ewes including BCS measurements manually evaluated by the farm manager, BCF measurements determined by computerized tomography (CT) and body parameter measurements automatically determined by an image processing application. Artificial neural network (ANN) statistical analysis method was used to develop a relationship between the body parameters and the BCF with an r2=0.96 and RMSE=1.01 using all top and side variables.

While some research supports utilizing plain radiography for measuring biomechanical alignment of the spine for prognosis and treatment, there are contrasting viewpoints regarding both the value and utilization of these procedures in conservative care. Evaluation of both conservative and non-conservative approaches to spinal care revealed vast differences in radiographic utilization and interpretation between orthopedic surgeons, primary care physicians, chiropractic physicians, and physical therapists, which may account for the different viewpoints and rationale in the literature. A research summary is provided regarding the various methods of spinal analysis utilized by these professions to help determine if there is any unique diagnostic or prognostic value associated with radiographic utilization that could assist in advancing conservative spinal assessment and treatment. Understanding any unique value provided through biomechanical assessment utilizing plain radiography of the spine established in the literature may help chiropractic physicians determine the appropriate use of radiographic procedures in clinical practice and how to coordinate efforts with other conservative and non-conservative professions to improve spinal healthcare.

: Background: Overweight and obesity are major risk factors for many chronic diseases, and weight-loss interventions often include systematic exercising and nutritional supplements. The purpose of this study was to determine the independent/synergistic effects of Spirulina maxima supplementation (6-week, 4.5 g/day) and a systematic physical exercise program (6 weeks/ 2 times) on body composition and cardiorespiratory fitness of overweight and obese subjects. Methods: 27 overweight and 25 obese sedentary male subjects were assigned to four interventions through a randomized double-blind, crossover controlled trial: Physical exercise program with (SE) or without (Ex) Spirulina maxima or no-exercise program with (Sm) and without (C) Spirulina maxima. Body composition and cardiorespiratory fitness parameters were taken during a maximal intensity test. Results: As compared to C group, SE, Sm and Ex groups reduced (p < 0.05) their body fat percentage while improving their maximal oxygen uptake (VO₂max; r = −0.40), being obese subjects more benefited. Weight loss, time to reach fatigue and onset of blood lactate accumulation were improved in both Spirulina maxima supplemented groups, regardless the subjects’ body composition. Conclusions: Spirulina maxima supplementation synergistically improves the effects of systematic exercise in body composition and cardiorespiratory fitness parameters in overweight but mostly in obese adults.

The problem of simulating wakes in a stratified oceanic environment with active background turbulence is considered. Anisotropic RANS turbulence models are tested against laboratory and eddy-resolving models of the problem. An important aspect of our work is to acknowledge that the environment is not quiescent; therefore, additional sources are included in the models to provide a non-zero background turbulence. The RANS models are found to reproduce some key features from the eddy-resolving and laboratory descriptions of the problem. Tests using the freestream sources show the intuitive result that background turbulence causes more rapid wake growth and decay.

This study was first time designed to investigate the effect of oxidation on protein digestion and transport properties in boiled sea cucumber body wall (BSCBW) via simulated digestion combine with everted-rat-gut-sac models. Boiling heat treatments led to protein oxidation in SCBW, manifested by increases in free radical intensity, thiobarbituric acid reactive substances, carbonyl groups, disulfide bonds, dityrosine bonds, advanced glycation end products, protein hydrophobicity and aggregation, declines in free sulfhydryl group, and secondary structure transition from α-helix to β-sheet. Boiling for 2 h caused the anti-digestion collagen unfolding, provided the action site for protease, and improved the protein digestion and transport levels. On the contrary, excessive oxidative modification of 4 h-BSCBW resulted in decreased protein digestion and transport levels. From the perspective of texture, digestion and transport properties, boiling for 2 h can obtain sea cucumber products with better edible and digestible properties, which is considered to be a better processing condition.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

The genetic heterogeneity of autism has stymied the search for causes and cures. Whole-genomic studies on large numbers of families have helped identify combinations of inherited and de novo signal. In the present work, we re-analyze DNA microarrays using a novel strategy that takes prior knowledge of genetic relationships into account and that was designed to boost signal important to our understanding of the molecular basis of autism. Our strategy was designed to identify significant genomic variation within a priori defined biological concepts and improves signal detection while lessening the severity of multiple test correction seen in standard analysis of genome-wide association data. Upon application of our approach using 3,244 biological concepts, we detected genomic variation in 68 biological concepts with significant association to autism in comparison to family-based controls. These concepts clustered naturally into a total of 19 classes, principally including cell adhesion, cancer, and immune response. The top-ranking concepts contained high percentages of genes already suspected to play roles in autism or in a related neurological disorder. In addition, many of the sets associated with autism at the DNA level also proved to be predictive of changes in gene expression within a separate population of autistic cases, suggesting that the signature of genomic variation may also be detectable in blood-based transcriptional profiles. This cross-validation with gene expression data from individuals with autism coupled with the enrichment within autism-related neurological disorders supported the possibility that the mutations play important roles in the onset of autism and should be given priority for further study. Our work provides new leads into the genetic underpinnings of autism and highlights the importance of reanalysis of genomic studies of complex disease using prior knowledge of genetic organization.

We presented unusual case of double left ventricular false aneurysm complicating late presentation AMI successfully treated with the combination of urgent surgical drainage of tamponade, staged PCI of non-culprit lesion, preventive implantation of ICD-DR, guideline directed heart failure medical therapy and delayed but effective reconstructive operation.

Aboriginal Australians have a fundamental human right to opportunities that lead to healthy and flourishing lives. While the impact of trauma on Aboriginal Australians is well-documented, a pervasive deficit narrative that focuses on problems and pathology persists in research and policy discourse. This narrative risks further exacerbating Aboriginal disadvantage, through a focus on ‘fixing what is wrong’ with Aboriginal Australians, and the internalising of these narratives by Aboriginal Australians. While a growing body of research adopts strength-based models, limited research has sought to explore Aboriginal flourishing. This conceptual paper seeks to contribute to a burgeoning paradigm shift in Aboriginal research, seeking to understand what can be learned from Aboriginal people who flourish, how we best determine this, and in what contexts this can be impactful. Within, we argue the case for a new approach to exploring Aboriginal wellbeing that integrates salutogenic, positive psychology concepts with complex systems theory to understand and promote Aboriginal wellbeing and flourishing, While deeper work may be required to establish the parameters of a strength-based, culturally aligned Aboriginal conceptualisation of positive psychology, we suggest the integration of Aboriginal and Western methodologies offer unique and potent means of shifting the dial on seemingly intractable problems.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

The microbiome gut brain (MGB) axis involves bidirectional routes of communication and has emerged as a potential therapeutic target for multiple medical specialities including psychiatry. Significant numbers of preclinical trials have taken place with some transitioning to clinical studies in more recent years. Some positive results have been reported secondary to probiotic administration in both healthy populations and specific patient groups. This review aims to summarise the current understanding of the MGB axis and the preclinical and clinical findings relevant to psychiatry. The link between the gut microbiome and irritable bowel syndrome (IBS) is well established. Significant differences have been identified between the microbiome of patients with a diagnosis of depressive disorder and healthy controls. Similar findings have occurred in patients diagnosed with bipolar affective disorder. A probiotic containing Lactobacillus acidophilus, Lactobacillus casei, and Bifidobacterium bifidum produced clinically measurable symptom improvement in patients with depressive disorder. To date some promising results have suggested that probiotics could play a role in the treatment of stress-related psychiatric disease. However, more well-controlled clinical trials are required to determine which clinical conditions are likely to benefit most significantly from this novel approach.

Background: The effect of COVID-19 infection, versus the indirect effect of the pandemic on body composition remains unclear. This study investigates long-term changes in body composition in COVID–19 survivors compared to a contemporary control group. Method: This is a prospective study involving adults who had a pre-pandemic whole-body DXA scan (DXA#1) performed between 2017 and 2019. Participants were asked to return for a repeat whole-body DXA scan (DXA#2) after the pandemic. Detailed data were collected including medical and COVID history. Inflammation markers and fasting lipids were measured. For those participants who had a COVID-19 infection between the 2 DXAs, DXA#2 was acquired at least one year after COVID-19 infection. Results: Overall, 160 adults were enrolled; 32.5% females, 51.8% non-white, with mean age of 43.2 years. Half (n=80) of the participants had documented COVID infection between their 2 DXA scans (COVID+ group), and the other half never had COVID. COVID-negative participants had an increase in annualized trunk fat (g) [922.5 vs. 159.7; P=0.01], total fat (g) [1564.3 vs. 199.9; P=0.2], and LBM (g) [974.9 vs. -64.5; P=0.0002], when compared to COVID+ group. However, among the COVID+ group, no differences were seen in annualized trunk fat, total fat mass, or LBM between those with PASC and without (p>0.05). Conclusion: During the pandemic, both COVID-19-survivors and COVID-negative groups exhibited increases in weight, and total and trunk fat, likely associated with pandemic-linked lifestyle modifications. However, only COVID-19-survivors had a decline in lean body mass over the same period, regardless of PASC symptoms.

Suicide is a public health problem influenced by a variety of biological, psychological, social, and environmental factors. Recognizing the warning signs at each stage is crucial for prevention and helping those at risk. In this context, body awareness, especially interoceptive body awareness, emerges as a potentially relevant and underexplored factor. In this study, binary logistic regression and linear regression analyses were used to examine the relationship between interoceptive body awareness and suicidal orientation in Colombian university students. In addition, the bootstrap technique was used to resample and estimate the distribution of the data. The results support the idea that greater interoceptive awareness may protect against suicidal orientation by improving emotional regulation. An inverse relationship was found between interoceptive awareness and suicidal ideation. These findings are consistent with previous literature on the importance of body awareness for emotional well-being. Further longitudinal research is needed to explore this relationship in depth.

Despite the recognized influence of maximum or acceleration strength on combat techniques and countermovement jump (CMJ) performance, the relationship between body segment weights and combat techniques remains unexplored. This study aimed to examine the impact of body segment weights, including striking arm weight (SAW), kicking leg weight (KLW), and trunk weight (TW), on the dynamics of direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and CMJ performance. Sixteen male military cadets (22.3±1.8 years, 181.4±7.0 cm, 83.0±8.1 kg) performed combat techniques, with performance measured by using a force plate and body segment weights assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis was applied. Results indicated a strong correlation between KLW and FK impulse (r = 0.64, p ≤ 0.01) and CMJ impact force (r = 0.80, p ≤ 0.01). SAW showed moderate correlations with DP impulse (r = 0.53, p ≤ 0.05) and ES impulse (r = 0.54, p ≤ 0.05). Additionally, FK peak and impact forces were strongly correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01), and FK peak force moderately correlated with CMJ peak velocity (r = 0.63, p ≤ 0.05). These findings suggest targeted arm strength training could enhance striking abilities, while improvements in leg acceleration strength may directly boost kicking performance and vertical jump capabilities, which are crucial in combat scenarios.

Vaccines decrease morbidity and mortality. Nevertheless, their benefits depend on public response. During COVID-19, vaccine hesitancy and refusal were rampant, threatening public health. A thorough understand-ing of opponents' arguments is required to address the diffusion of unreliable information on social media and prevent vaccine hesitancy from developing into vaccine refusal. Accordingly, the article examines vac-cine opponents' justifications on social media. Textual content analysis of reader comments on three health-related Israeli Facebook pages was conducted. Data collection encompassed the Israeli COVID-19 vaccination period from October 2020 to May 2022. The comments were analyzed according to the health beliefs model (HBM). We found that vaccine opponents were characterized by low perceptions of the severity of the disease combined with high perceptions of the damages of the vaccine; low perceived benefits of vac-cine compliance; vaccine hesitancy and fear along with public distrust as barriers to change; and call for ac-tion to resist the vaccine and spread related anti-establishment views on the web. As vaccination hesitancy was found to develop into public distrust in the state systems and escalate into conspiracy beliefs and an-ti-vaccination activism, its early detection may prevent future vaccine resistance.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

Major (exo)planetary and satellite bodies seem to concentrate at intermediate areas of the radial 1 distributions of all the objects orbiting in each (sub)system. We show that angular-momentum transport during secular evolution of (exo)planets and satellites necessarily results in the observed intermediate accumulation of the massive objects. We quantify the ‘middle’ as the mean of mean motions (orbital angular velocities) when three or more massive objects are involved. Radial evolution of the orbits is expected to be halted when the survivors settle near mean-motion resonances and angular-momentum transfer between them ceases (gravitational Landau damping). This dynamical behavior is opposite in direction to what has been theorized for viscous and magnetized accretion disks, in which gas spreads out and away from either side of any conceivable intermediate area. We present angular momentum transfer simulations in few-body systems, and we calculate the tidal dissipation timescales and the physical properties of the mean tidal field in planetary and satellite (sub)systems.

The anthropometric features offer an overall image of the nutritional status. The investigated groups were aged 19 and 21. The anthropometric measurements of height and weight were recorded following standard procedures. The objectives of this study were to evaluate the harmonious body development, the nutrition status and the body composition. The evolution of the stature increases until 20 years after which stagnation follows. The body mass index of subjects was found to be normal. The body fat may vary over time in subjects depending on age and gender. Body water and body muscle mass content increased with age. The harmony of body development was assessed by means of the Amar index. Regarding the constitutional index, the women subjects belong to the leptosome type and the male subjects belong to the picnic type. The status of the investigated subjects is within the average stature.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

This review is a first attempt at bringing together various concepts from research on wall- and magnetically-bounded turbulent flows. Brief reviews of both fields are provided: The main similarities identified are coherent (turbulent) structures, flow generation and transport barriers. Examples are provided and discussed.

Relationships between drought and fire danger indices are examined to 1) incorporate fire risk information into the National Integrated Drought Information System California-Nevada Drought Early Warning System and 2) provide a baseline analysis for application of drought indices into a fire risk management framework. We analyzed four drought indices that incorporate precipitation and evaporative demand (E₀) and three fire indices that reflect fuel moisture and potential fire intensity. Seasonally averaged fire danger indices were most strongly correlated to multi-scalar drought indices that use E₀ (the Evaporative Demand Drought Index [EDDI] and Standardized Precipitation Evapotranspiration Index [SPEI]) at approximately annual time scales that reflect buildup of antecedent drought conditions. Results indicate that EDDI and SPEI can inform seasonal fire potential outlooks at the beginning of summer. An E₀ decomposition case study of conditions prior to the Tubbs Fire in Northern California indicate high E₀ (97th percentile) driven predominantly by low humidity signaled increased fire potential several days before the start of the fire. Initial use of EDDI by fire management groups during summer and fall 2018 highlights several value-added applications, including seasonal fire potential outlooks, funding fire severity level requests, and assessing set-up conditions prior to large, explosive fire cases.

Older adults with obesity have an increased risk for cognitive decline and subsequent Alzheimer’s disease. Previous research has focused on the impact of individual nutrients and overall dietary patterns to improve cognitive function. The Brain and Body Health (BB-Health) study aims to demonstrate the feasibility of a multicomponent nutritional supplement (MCNS) and weight loss (WL) intervention for individuals with overweight and obesity who are not consuming a healthy diet. BB-Health is a parallel-group randomized placebo-controlled 2x2 factorial pilot trial comparing the MCNS, WL, and MCNS+WL with a Control group. Eligible participants are 55 to 85 years of age with a body mass index 27.0 to 39.9 kg/m2. Major exclusion criteria include type 2 diabetes, moderate or severe cognitive impairment, and self-reported healthy dietary pattern. The BB-Health feasibility trial is registered as NCT05542199 at clinicaltrials.gov. The BB-Health objectives are to report: 1) recruitment and enrollment, including pace and descriptive statistics of the study sample; 2) adherence to the administered interventions; 3) successful data collection and performance of outcome assessments, including evaluation of change in key outcomes over time that are powered for this pilot study; and 4) summary statistics on outcomes for use in planning a subsequent, larger trial. The outcomes of interest are age-sensitive cognitive assessments, cerebral hemodynamics, and related health parameters. All measurements are collected at baseline, 3-, 6-, and 12-month visits. If the BB-Health protocol demonstrates feasibility, the novel MCNS with and without a parallel WL intervention has potential to be administered in a confirmatory randomized trial to evaluate ability to prevent age-related cognitive decline and improve brain health. The BB-Health Feasibility Study could significantly contribute to our understanding of the influence of diet and weight management on cognitive health

Spacetime torsion is known to be highly suppressed at the end of inflation, called preheating. Of course this fact does not avoid that metric could affect the cosmic dynamos at preheating phase as was showed by Bassett et al, in the general relativity (GR) case. In this paper, is to show that a torsionful magnetogenesis in QED effective lagrangean, drives either a torsion damping or an amplification mechanism or dynamo effect, depending upon torsion chirality. The present extension of Basset et al theory yields a new magnetic field expression $B\sim{a^{(1\pm{\beta})}}$, obtained from dynamo equation in QED. Here a cosmic factor ${\beta}=g_{T}{\eta}k$ is present. In a second example we find Higgs inlationary fields in Einstein-Cartan gravity thick domain walls (DWs). Recently a moodified Einstein-Cartan gravity was given by M Shaposhnikov et al [PRL (2020)] to obtain higgs like inflatons as a portal to dark energy.

This purpose was to compare the ability of body shape index (ABSI) and body roundness index (BRI) with waist circumference (WC), body mass index (BMI), waist-to-hip ratio (WHR), waist-to-height ratio (WHtR) and body adiposity index (BAI) to predict metabolic risk. The cross-sectional study was conducted in 17,360 Chinese subjects (were aged 18-95 years old) who escaped cardiovascular disease (CVD) or diabetes. Biochemical and anthropometric variables were measured by trained staff. Receiver operating characteristic curve (ROC) and optimal cutoff values of obesity indices were recruited to compare the predictive ability for metabolic risk factors. The mean age of subjects was 53.7(13.1) years, 41.6 % were males. Within young group (<60 years), the areas under the curve (AUC) demonstrated that WC, BMI, WHR, WHtR and BRI were able to similarly predict high metabolic risk in males (0.74 vs. 0.74 vs. 0.73 vs. 0.73 vs. 0.73) and in females (0.73 vs. 0.73 vs. 0.71 vs. 0.73 vs. 0.73), while the approximate predictive ability were only acquired in males (0.73 vs. 0.73 vs. 0.70 vs. 0.73 vs. 0.73) within elder group (≥60 years). The optimal cut-off values of BRI for high metabolic risk were calculated in males (<60 y: 3.49 vs. ≥60 y: 3.46) and females (<60 y: 3.47 vs. ≥60 y: 3.60). Meanwhile, BRI displayed a strong prediction to elevated BP and elevated TG in males (AUC = 0.64; AUC = 0.70) and to elevated BP, elevated TG and elevated SUA in females (AUC = 0.67; AUC = 0.69; AUC =0.70). BRI was able to similarly predict high metabolic risk compared to WC, BMI, WHR, WHtR and BAI, while ABSI was not. Moreover, BRI revealed specific predictive ability for elevated BP, elevated TG and elevated SUA.

The Brazilian livestock is predominantly extensive, with approximately 90% of the production being sustained on pasture, which occupies around 20% of the territory. In the current climate change scenario and where cropland is becoming a limited resource, there is a growing need for a more efficient land use and occupation. It is estimated that more than half of the Brazilian pastures have some level of degradation; however there is still no mapping of the quality of pastures on a national scale. In this study, we mapped and evaluated the spatio-temporal dynamics of pasture quality in Brazil, between 2010 and 2018, considering three classes of degradation: Absent (D0), Intermediate (D1), and Severe (D2). There was no variation in the total area occupied by pastures in the evaluated period, in spite of the accentuated spatial dynamics, with a retraction in the center-south and expansion to the north, over areas of ​​native vegetation. The percentage of non-degraded pastures increased ~12%, due to the recovery of degraded areas and the emergence of new pasture areas as a result of the prevailing spatial dynamics. However, about 44 Mha of the pasture area is currently severely degraded. The dynamics in pasture quality were not homogeneous in property size classes. We observed that in the approximately 2.68 million properties with livestock activity, the proportion with quality gains was twice as low in small properties compared to large ones, and the proportion with losses was three times greater, showing an increase in inequality between properties with more and less resources (large and small, respectively). The areas occupied by pastures in Brazil present an unique opportunity to increase livestock production and make available areas for agriculture, without the need for new deforestation in the coming decades.

Farmers are continually looking for new reliable, objective and non-invasive methods for evaluation of ewe condition. Live weight (LW) and body condition score (BCS) are used by farmers as a basis to determine the condition of the animal. Body composition is an important aspect of monitoring animal condition. The body composition is the amount of fat, lean and bone; knowing the amount of each is important because the information can be used for better strategic management interventions. Experiments were conducted to establish the relationship between body composition and body parameters, at key life’s stages (weaning and pre-mating), using measurements automatically determined by an image processing ap-plication at Lincoln University sheep farm for 88 Coopworth ewes. Computerized Tomography technology was used to develop relationship with body parameters and a subset was used to validate the predicted model. Multivariate linear regression (MLR), artificial neural network (ANNs) and regression tree (RT) statistical analysis methods were evaluated to determine their efficacy to predict body fat, lean and bone. The results showed a correlation between fat, lean and bone determined by CT and the fat, lean, bone weight estimated by live weight and body parameters calculated using the image processing application with R2 values of 0.90 for fat, 0.72 for lean and 0.50 for bone using ANNs statistical model. From these results, farmers can utilize accurate measures of fat which will enhance nutritional and management practices.

Controlling the concentration of free radicals in polymerization systems is advantageous for preparing cationic polyacrylamide (CPAM) with high molecular weight and acceptable dissolvability. In this study, a novel ultraviolet (UV)-initiated system characterized with adjustable light intensity and redox-azo complex initiator was used to synthesize a CPAM flocculant named NP. Comparatively, another CPAM flocculant named SP with stable UV light intensity and single initiator was prepared. The chemical structure, morphology, and thermal stability were analyzed through instrumental analysis. Proton nuclear magnetic resonance indicated that NP was successfully prepared, and a small fraction of cationic homopolymer was mixed in the product. Polymerization conditions were optimized, and polymerization mechanism was determined by investigating the effects of various parameters on intrinsic viscosity, conversion, and dissolvability. Results showed that the best performance was obtained at indexes of 0.45 wt‰ redox initiator concentration, 0.2 wt‰ azo initiator concentration, 40.0 wt% of cationic monomer, first- and second-stage light intensities of 8.5 and 13 mW/cm², respectively, and 3 wt% urea. Sludge conditioning performances of NP and SP were comparatively evaluated, and the mechanism was determined by investigating the sedimentation behavior and floc size distribution. High intrinsic viscosity, porous morphology structure, and the mixed cationic homopolymer of NP resulted in better sludge conditioning performance.

The envelope (façade) of a building is the first barrier between the exterior and the interior of the building and withstands the highest variation of temperature and solar radiation. Trombe walls are used to take advantage of that and contribute to the heating of interior air, helping the heating system. In this study, a new Trombe wall design is presented with the aim to contribute significantly to the ventilation of residential buildings. For this an exterior wall equipped with a proposed Trombe system was studied in a numerical simulation analysis. The proposed systems consist of two parts, the air cavities on the exterior of the wall, covered with silica glass, and another layer used for heat transfer, on the interior, comprised of a MPCLBs wall of 115mm. Two cities in Romania were considered to represent the coldest and hottest climate in Romania. Brașov representing the cold climate and Constanța representing the hot climate. In the investigation, both the presence and absence of solar radiation were taken into account. In total 4 cases were established. For all four cases monthly research was made using monthly means temperature, direct and diffuse solar radiation. The results are promising and illustrate that the system works the best during the transitional seasons of spring and autumn. The lower the outdoor temperature the higher the temperature can be increased. Overall, solar radiation accounted for an average of 2 °C increase. The temperature increase varied between 3.4 °C to 15.99 °C for Brașov and between 6.42 °C to 12.07 °C in Constanța.

The incidence of obesity which leads to insulin resistance (IR) and metabolic disorder increases in developing countries including Indonesia. Male adult has higher risk to have abdominal obesity than female which is associated with cardiometabolic disorders. Several anthropometric measurements have been proposed to predict IR. The aim of this study was to investigate whether body mass, body mass index (BMI), waist circumference (WC), body fat percentage (BF) or visceral fat percentage (VF) could become a better predictor of IR in healthy young male adult. Total of 140 healthy young male adults ranging from 18-25 years were recruited in the study. Insulin resistance was measured by calculating Homeostatic Model Assessment for Insulin Resistance (HOMA-IR). Subjects with HOMA-IR value >75th percentile with cut off 3.75 were defined as IR. Anthropometric measurements included body weight, BMI, WC were performed whereas BF and VC were measured by bioelectrical impedance analysis (BIA). IR had significant strong correlation with body weight, BMI, WC, BF and VF. The area under curve of body mass, BF, VF were greater than WC and BMI. Anthropometric measurements correlated strongly with IR but body weight, BF, VF have stronger correlation than WC and BMI in healthy young male adult.

Free-living terrestrial mites (Acari) have persisted through numerous glacial cycles in Antarctica. Very little is known, however, of their genetic diversity and distribution, particularly within the Ross Sea region. To redress this gap, we sampled for mites throughout the Ross Sea region, East Antarctica, including Victoria Land and the Queen Maud Mountains (QMM), covering a latitudinal range of 72-85oS, as well as from Lauft Island near Mt Siple (73oS) in West Antarctica and Macquarie Island (54oS) in the sub-Antarctic. We assessed genetic diversity using mitochondrial cytochrome c oxidase subunit I gene sequences (COI-5P DNA barcode region), and also morphologically identified voucher specimens. We obtained 130 sequences representing four genera: Nanorchestes (n = 30 sequences), Stereotydeus (n = 46), Coccorhagidia (n = 18) and Eupodes (n = 36). Tree-based analyses (maximum likelihood) revealed 13 genetic clusters, representing as many as 23 putative species indicated by Barcode Index Numbers (BINs) from the Barcode of Life Datasystems (BOLD) database. We found evidence for geographically-isolated cryptic species, e.g. within Stereotydeus belli and S. punctatus, as well as unique genetic groups occurring in sympatry (e.g. Nanorchestes spp. in QMM). Collectively, these data confirm high genetic divergence as a consequence of geographic isolation over evolutionary timescales. From a conservation perspective, additional targeted sampling of understudied areas in the Ross Sea region should be prioritised, as further diversity is likely to be found for these short-range endemic mites.

This study aims to investigate the impact of body heat loss on the thermal and aerodynamic conditions in a whole-body cryotherapy chamber. The underlying hypothesis is that the heat generated by the human body alters the thermal and aerodynamic environment inside the cabin. A numerical study was conducted to test this hypothesis to analyze the thermodynamic exchanges between the human body and the cabin during a 3-minute whole-body cryotherapy session. The computational fluid dynamics (CFD) approach was used to study the unsteady heat transfer between the human body and the interior of the cryotherapy cabin. A thermal boundary condition, based on a mathematical model developed from experimental data, was applied to simulate skin cooling kinetics over time. The post-processing of the 3D results, including temperature, velocity fields, and thermal flux maps at the body surface, provided insight into the thermo-convective mechanisms involved in a whole-body cryotherapy session. The study found that body heat loss significantly affects the temperature fields inside the cabin, leading to global modifications of the aeraulic and thermal conditions. These findings suggest that cryotherapy protocols may need to be adjusted or the cabin set temperature optimized to enhance the therapeutic benefits.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

Throughout the eukaryotic tree of life, amoeboid organisms have evolved that aggregate upon starvation and form multicellular fruiting bodies, consisting of a ball of spores atop a stalk. This chapter discusses the remarkable convergent evolution of a stalked fruiting body in these different taxa. It then discusses a well-studied group of aggregative fruiters, the cellular slime molds, in more detail. These organisms exhibit substantial variation in their stalk formation and composition, which allows a better understanding of the evolution, maintenance and possible functions of stalked fruiting bodies, but also points to potential costs and benefits of different types of stalks.

Background and Objective: Although whole body-electromyostimulation (WB-EMS) has been shown to favorably improve body composition in several research studies, it has not been confirmed how it affects adipose tissue-derived biomarkers and circumferences of the abdomen and thighs. Materials and Methods: Twenty participants of obese elderly women were randomly classified into an EMS group (EMSG; n = 10) or a non-EMS group (CON; n = 10). The WB-EMS suits used in this study enabled the simultaneous activation of 8 muscle groups with selectable intensities for each phase. Stimulation frequency was selected at 85 Hz, impulse-width at 350 μ seconds, and impulse-rise as a rectangular application. Impulse duration was 6 seconds with a 4-second break between impulses. The EMS sessions were combined with aerobic dancing 3 times a week for 12 weeks. Both groups received the same program; however, the CON did not receive electrical stimuli. Biomarkers and body composition including circumferences of the abdomen and thighs were measured on Week 0 and Week 12. Results: Compared with the CON, 1) a significant effect of the EMS-intervention concerning decreased body weight (p = 0.032) and increased basal metabolic rate (p = 0.029) were evident. The thigh subcutaneous fat and total fat of EMSG were not significantly changed, but those of CON were significantly increased after 12 weeks. 2) The biomarkers of CON either increased or showed no change, although the interleukin (IL)-6 was significantly (p = 0.028) decreased in EMSG. Specifically, C-reactive protein (CRP; p = 0.005) and alpha-fetoprotein (p = 0.050) of CON were significantly increased after 12 weeks. In addition, the IL-6 (p = 0.034), CRP (p = 0.001), carcinoembryonic antigen (p = 0.017), and low density lipoprotein (p = 0.005) of EMSG were lower than those of CON in the end of experiment. 3) Conclusions: The results indicate that EMS intervention improved body composition and reduced negative biomarkers, thus highlighting its effectiveness.

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.

We delve into the axion-dilaton model within the supergravity framework, with a specific focus on the intricacies of domain wall construction and stability. Employing holographic vitrification, we unravel the dynamics of domain wall formation in gauge theories featuring periodic vacuum structures. Our model, incorporating a QCD-like axion term and a stabilizing dilaton, undergoes scrutiny for conductivity variations under weak disorder. The investigation reveals the model's resilience, manifesting near-perfect conductivity under mild disorder conditions. However, the rigorous mathematical motivation for the holographic setup demands further elucidation. The scattered nature of our results prompts the necessity for a more systematic interpretation of QCD phenomena and conductivity transitions. This study contributes to the mathematical understanding of the axion-dilaton model's behavior, highlighting the imperative for a refined holographic framework and a more coherent interpretation of observed phenomena.

Morphogenesis remains a riddle, wrapped in a mystery, inside an enigma. It remains a formidable problem viewed from many different perspectives of morphology, genetics, and computational modelling. We propose a biochemical reductionist approach that shows how both internal and external physical forces contribute to plant morphogenesis via mechanical stress-strain transduction from the primary cell wall tethered to the plasma membrane by a specific arabinogalactan protein (AGP). The resulting stress vector with direction defined by Hechtian adhesion sites, has a magnitude of a few picoNewtons amplified by a hypothetical Hechtian growth oscillator. This paradigm shift involves stress activated plasma membrane Ca2+channels and auxin-activated H+-ATPase. The proton pump dissociates periplasmic AGP-glycomodules that bind Ca2+. Thus, as the immediate source of cytosolic Ca2+ an AGP-Ca2+ capacitor directs vectorial exocytosis of cell wall precursors and auxin efflux (PIN) proteins. In toto these components comprise the Hechtian Oscillator and also the gravisensor. Thus interdependent auxin and Ca2+ morphogen gradients account for the predominance of AGPs. The size and location of a cell surface AGP-Ca2+ capacitor is essential to differentiation and explains AGP correlation with all stages of morphogenetic patterning from embryogenesis to root and shoot. Finally, evolutionary origins of the Hechtian Oscillator in the unicellular Chlorophycean algae reflect the ubiquitous role of chemiosmotic proton pumps that preceded DNA at the dawn of life.

Crown gall (Agrobacterium tumefaciens), crown/root rot (Phytophthora spp.), root lesion disease (Pratylenchus vulnus), and tree vigor are key traits affecting productivity and quality of walnuts in California. Non-inoculated hybrid rootstocks were analyzed by RNA-seq to examine pre-formed factors affecting these traits. Enrichment analysis of the differentially expressed genes revealed that increased expression of cell wall biogenesis-related genes plays a key role in susceptibility to A. tumefaciens, Phytophthora spp., increased vigor, but not P. vulnus. Analysis of the predicted subcellular loci of the encoded proteins revealed that many gene products associated with vigor and susceptibility were targeted to the plasma membrane and extracellular space, connecting these traits to sustaining barrier function. We observed that RNA processing and splicing, along with predicted nuclear targeting, were associated with resistance to A. tumefaciens, Phytophthora spp., low vigor, but not P. vulnus. Four genes within the J. microcarpa QTL region for resistance to A. tumefaciens and Phytophthora spp. were represented among our transcripts, with two of the genes being differentially expressed in association with resistance to A. tumefaciens and decreased vigor. No differential expression related to Phytophthora spp. or P. vulnus traits was observed in this region. Additionally, the J. microcarpa haplotype expressed more transcripts associated with resistance to A. tumefaciens, Phytophthora spp., and low vigor, but not P. vulnus than the J. regia haplotype. We also report unique and shared hormone and defense responses associated with each trait. This research suggests a link between cell wall biogenesis, vigor, and critical root diseases of walnut.

Background: Obesity among pregnant women is common, and their offspring are predisposed to obesity, insulin resistance, and diabetes. Circulating metabolites that are related to insulin resistance and are associated with this decreased tissue-specific uptake are unknown. Here, we assessed metabolite profiles in elderly women and who were either female offspring from obese mothers (OOM) or offspring of lean mothers (OLM). Metabolic changes were tested for associations with metrics for insulin resistance. Methods: 37 elderly women were separated into an elderly offspring from obese mothers (OOM; n = 17) and elderly offspring from lean/normal weight mothers (OLM; n = 20) groups. We measured plasma metabolites using 1H-NMR and also insulin-dependent tissue specific glucose uptake in skeletal muscle were assessed. Associations were made between metabolites and glucose uptake. Results: Compared to the OLM group, we found that the 22:6 docosahexaenoic acid percentage of the total long chain n-3 fatty acids (DHA/FA) was significantly lower in OOM (P = 0.015). DHA/FA associated significantly to skeletal muscle GU (P = 0.031) and M-value in the OLM group only (P = 0.050). Conclusions: DHA/FA is associated with insulin-dependent skeletal muscle glucose uptake and that this association is significantly weakened in the offspring of obese mothers.

Hemodynamic relevance of differently located stenoses of the internal jugular veins remains undetermined. It particularly concerns nozzle-like strictures in the upper parts of these veins and stenotic jugular valves located at the end of this vein. This study was aimed at understanding flow disturbances caused by such stenoses. Computational fluid dynamics software, Flowsquare+, was used. We constructed 3-dimensional models of venous outflow, comprising two alternative routes: tube representing the internal jugular vein and irregular network representing the vertebral veins. At the beginning of the tube representing the internal jugular vein, differently-shaped and sized short strictures, representing nozzle-like strictures were built in. At the end of this tube, differently-shaped membranes, representing the jugular valve, were built in. With the use of computational fluid dynamics modeling, we studied how these two obstacles influenced the outflow. We found that the most relevant outflow disturbances were evoked by nozzle-like strictures in the upper part of the internal jugular vein that were either small, long or asymmetrically positioned. Very tight stenotic valves and septum-like malformed valve were equally hemodynamically relevant. These findings suggest that both upper and lower strictures of the internal jugular vein can be of clinical significance.

Background Children often suffer the nonspecific musculosceletal pain as reported in literature. Aim To determine relationship between body weights with development of musculoskeletal pain and to determine whether growing in body height is associated with musculoskeletal pain in schoolchildren. Subjects/ Methods A prospective longitudinal study included 1315 school children aged 7-14 years (652 boys and 663 girls) and was performed in 13 elementary schools in B&H. Child body height and body weight were measured. The survey of perception of musculoskeletal pain in different body regions of subjects was conducted by adjusted Nordic Musculosceletal Questionnaire (NMQ). Results The highest prevalence of an overweight and obesity in the 10th year 35.7% and the lowest frequency 17.8% in the 14th year was. In the age 14th obesity was’nt found. Boys have more prevalence of overweight. Using logistic regression model, we found that school children with normal BMI were protected with increased body height of acute lower back pain (β= -0.089, 95%CI, -9.730- -0.023, P< 0.049), and increased body height was protector of obese school children of acute upper back pain (β= -0.356, 95%CI, -14.077- -3.878, P< 0.001) and chronic lower back pain (β= -0.356, 95%CI, -14.077- -3.878, P< 0.001). Conclusion Schoolchildren with normal weight more often have had musculosceletal pain than those with overweight or obesity. This can be associated with intense physical growth period in height, especially. The assumption is that the increase in height changes the relationship between excessive BMI and musculoskeletal pain in children of school age.

Body Expression (BE) has been defined in the past decades as a discipline within Physical Education (PE) with very particular characteristics and a strong emotional component. In this study, a programme of this discipline was applied to university Physical Activity and Sports Sciences (PASS) students from six consecutive academic years: three prior to and three during the pandemic. A pre-post design was used to determine how the BE programme affected the university students' self-concept (SC). To do so, a questionnaire with a multidimensional approach to this construct was administered, whose dimensions were closely related to the BE programme's characteristics. The results revealed significant improvements in the final SC, compared to the initial SC. Men reported lower SC values than women before the programme implementation, but higher at the end. Therefore, the change was larger in men, so the programme may have had an equalising effect between groups. It was also verified that the pandemic had particularly affected women.

In the weak-field approximation of covariant theory of gravitation the problem of 4/3 is formulated for internal and external gravitational fields of a body in the form of a ball. The dependence of the energy and the mass of the moving substance on the energy of field accompanying the substance, as well as the dependence on the characteristic size of the volume occupied by the substance are described. Additives in the energy and the momentum of the body, defined by energy and momentum of the gravitational and electromagnetic fields associated with the body are explicitly calculated. The conclusion is made that the energy and the mass of the body can be described by the energy of ordinary and strong gravitation, and through the energies of electromagnetic fields of particles that compose the body.

We are in amidst of COVID-19 pandemic. Since Dec 2019, severe acute respiratory corona virus (SAR-CoV-2) has infected more than half a billion people killing nearly 7 million people worldwide. Now the BA.5 variant of SARS-CoV-2 is causing mayhem and driving the global surge. Epidemiologist are aware of the fact that this virus is capable of escaping immunity and likely to infect the same person multiple times despite adequate vaccination status. Elderly people of age more than 60 years and those with underlying health conditions are considered as high-risk who are likely to suffer complications and death. While it is tempting to frame complications and mortality from COVID-19 as a simple matter of too much of a virulent virus in too weak of a host, much more is at play here. Framing the pathophysiology of COVID-19 in the context of the Chrousos and Gold model of the central stress response system can shed insight into its complex pathogenesis. Understanding the mechanisms by which pharmacologic modulation of the central stress response system via administration of clonidine and/or dexamethasone may offer an explanation as to why a viral pathogen can be well tolerated and cleared by one host while inflaming and killing another.

It is generally accepted that the human abdominal wall is comprised of skin, subcutaneous tissues, muscles and their aponeuroses, and the parietal peritoneum. Understanding these layers and their mechanical properties provides valuable information to those designing procedural skills trainers, supporting surgical procedures (hernia repair), and engineering-based work (in silico simulation). However, there is little literature available on the mechanical properties of the abdominal wall in layers or as a composite. This work characterizes the tensile properties of the human abdominal wall by layer and as a partial composite. Tissues were collected from fresh-never-frozen and fresh-frozen cadavers and tested in uniaxial tension at a rate of 5 mm/min until failure. Stress-strain curves were created for each sample, and the values for elastic moduli, ultimate tensile strength, and strain at failure were obtained. The experimental outcomes from this study demonstrated variation of tensile properties within and between tissues. The data also suggest that the tensile properties of composite abdominal walls are not additive. Ultimately, this body of work contributes to a deeper comprehension of these mechanical properties and will serve to enhance patient care, refine surgical interventions, and assist with more sophisticated engineering solutions.

The present study provides new insights into the growth of brown algal cell wall by showing that cell wall polysaccharide plays an important role in the process of growth consider- ing the physicochemical characteristic of young and old Cladosiphon okamuranus. To determine its structural variation in detail, the cell wall was sequentially fractionated into five fractions: hot water (HW), ammonium oxalate, hemicellulose-I (HC–I), HC-II, and cellulose, and analyzed physicochemically. Results showed that almost 80% of the total recovery cell wall from both young and old thalli was HW and HC-I contained mainly fucoidan composed of Fuc, GlcA, and sulfate in molar ratios of 1.0: 0.3: 0.6~0.7 and 1.0: 0.3: 0.2~0.3, respectively. Fucoidan in HW was a highly sulfated matrix polysaccharide abundance in young thalli, while fucoidan in HC-I was rich in old thalli and functions as hemicellulose in land plants, crosslink with cellulose and strengthen the cell wall. We found that HW and HC-I were particularly involved in the growth and strength of old thalli appeared to be due to the deposition of HC-I and reducing of water content during the growth process.

In this paper, we present and analyze a compact inner-wall grating slot microring resonator (IG-SMRR) with the footprint of less than 13 μm × 13 μm on the SOI platform for label-free sensing, which comprises a slot microring resonator (SMRR) and inner-wall grating (IG). Its detection range is significantly enhanced without the limitation of the free spectral region (FSR) owing to the combination of SMRR and IG. Structural parameters of IG and SMRR are investigated and optimized for favorable transmission properties. The simulation results shows that the IG-SMRR has an ultra-large quasi-FSR of 84.6 nm, and the concentration sensitivities of sodium chloride solutions and D-glucose solutions are up to 960.61 pm/% and 933.06 pm/%, respectively. The investigation on the combination of SMRR and IG is a valuable exploration of label-free sensing application for ultra-large detection range and ultra-high sensitivity in future.

A labyrinth metamaterial wall with glass coverage is measured in a reverberating chamber and after its installation in a restaurant. Glass is used to meet two aims, namely acoustic absorption and visual design demands. The wall consists of five multiple labyrinth elements of 1.83 m$^2$ each. Glass was taken to make the wall act as a room lightning device where a translucent cover material is needed. Absorption measurements show about four times improved absorption compared to typical glass. Due to the metamaterial behavior, absorption is high in the low-frequency range below 300 Hz where damping is problematic with traditional materials. Especially in this range, the glass metamaterial wall is an excellent compromise between room acoustic and visual design demands, as loud low-frequencies make visitors speak louder and experience less intimacy with additionally reduced speech intelligibility. For mid-frequencies, absorption is shown less effective and improvements are discussed.

Topological states of matter have attracted significant attention due to their intrinsic wave-guiding and localization capabilities robust against disorders and defects in electronic, photonic, and phononic systems. Despite the above topological features phononic crystals share with their electronic and photonic counterparts, finite-frequency topological states in phononic crystals may not always survive. In this work, we discuss the survivability of topological states in Su-Schrieffer-Heeger models with both local and non-local interactions with larger symmetry perturbation. Although such a discussion is still about ideal mass-spring models, the insights from this study set the expectations in continuum phononic crystals, which can further instruct the applications of phononic crystals for practical purposes.

1). BACKGROUND: Cell wall deficient mycobacteria (CWDM) have seldom been isolated in bacterial culture from human subjects. particularly in clinical disease, such as Crohn’s disease. Techniques have focused on the use of polymerase chain reaction (PCR) for the detection of CWDM in association with inflammatory bowel disease. (IBD). This paper is a report of the development of methods to demonstrate the presence of CWDM using the Ziehl-Neelsen (ZN) stain. This is in addition to the detection of the growth of CWDM in fluid media. 2). METHODS: The use of the ZN stain is suitable for the demonstration of CWDM in clinical samples and cultures, when the staining methods that were common prior to the 1970’s, are adopted. Specific culture media are developed and tested in parallel. Alterations in the concentration of basic fuchsin, and changes in the decolourising solutions are necessary. Decolourising solutions such as 20% concentrated sulphuric acid in water are preferable for detection of CWDM in cultures. 3). RESULTS: CWDM can be readily demonstrated using the simple methods outlined in this report. The ability to visualise the presence of CWDM opens the door to the development of specific fluid media for the isolation of CWDM in culture. 4). CONCLUSION: The ZN stain methods optimised for the demonstration of Mycobacterium tuberculosis complex (MTBC) are not suitable for research into infectious causes of inflammatory bowel disease (IBD), as well as for the detection of CWDM in latent tuberculosis. Revisiting the techniques for the detection of CWDM may also refocus attention on inflammatory diseases considered to be idiopathic, but having hallmarks of an infectious process.

This research elucidates the dynamic expression of expansin genes during the wheat grain (Triticum aestivum L.) development process using comprehensive meta-analysis and experimental validation. We leveraged RNA-seq data from multiple public databases, applying stringent criteria for selection, and identified 60,852 differentially expressed genes across developmental stages. From this pool, 28,558 DEGs were found to exhibit significant temporal regulation in at least two different datasets, and were enriched for processes integral to grain development such as carbohydrate metabolism and cell wall organization. Notably, 30% of the 241 known expansin genes showed differential expression during grain growth. Hierarchical clustering and expression level analysis revealed temporal regulation and distinct contributions of expansin subfamilies during the early stages of grain development. Further analysis using co-expression networks underscored the significance of expansin genes, revealing their substantial co-expression with genes involved in cell wall modification. Finally, qPCR validation and grain morphological analysis under field conditions indicated a significant negative correlation between expression of select expansin genes and grain size and weight. This study illuminates the potential role of expansin genes in wheat grain development and provides new avenues for targeted genetic improvements in wheat.

With the objective of studying the influence of elicitors on growth, yield and quality of kalmegh we carried out an investigation for two consecutive years. Nine treatments with three replications were laid out in CRD design. Chitosan, Yeast extract, Jasmonic acid and Salicylic acid were evaluated at different concentrations. CHT 1000 ppm exhibited highest plant height (73.91 cm) and secondary branches (29.07) at the time of harvest. Primary branches and number of leaves per plant were highest in CHT 1000 ppm (26.36; 88.32) which were on par with SA 200 ppm (26.28; 81.51). Plant spread was highest in SA 200 ppm (35.46 cm2) which was on par with CHT 1000 ppm (35.11 cm2). CHT and SA sprays were recorded with on par results for yield parameters but highest fresh (42.34 g) and dry (18.30) herbage yield per plant were exhibited with SA 200 ppm. Highest total chlorophyll (4.459 mg g-1) and total andrographolides (3.494%) content were recorded in SA 200 ppm spray. Significant and positive improvement in growth, yield and quality of kalmegh was noticed with Salicylic acid spray @ 200 ppm at 30 and 60 DAS signifying its use in cultivation of kalmegh for high productivity, quality and better returns for farmers.

Aflatoxins, which have been classified as a group-1 carcinogen are the well-known mycotoxins produced by Aspergillus flavus. Aflatoxins have been linked to liver diseases, acute hepatic necrosis, resulting in cirrhosis or hepatocellular carcinomas due to which it incurs a loss of value in international trade for peanuts contaminated with it. The four main aflatoxins are B1, B2, G1, and G2 of which B1 is predominant. In plants, the cell wall is the primary barrier against pathogen invasion. Cell wall fortifications such as deposition of callose, cellulose, lignin, phenolic compounds and structural proteins help to prevent the pathogen infection. Further, the host cell’s ability to rapidly repair and reinforce its cell walls will result in a reduction of the penetration efficiency of the pathogen. Peanut seed coat acts as a physical and biochemical cell wall barrier against both pre and post-harvest pathogen infection. The structure of seed coat and the presence of polyphenol compounds have been reported to inhibit the growth of A. flavus, however, not successfully employed to develop A. flavus resistance in peanut. A comprehensive understanding of peanut seed coat development and biochemistry will provide information to design efficient strategies for the seed coat mediated A. flavus resistance and Aflatoxin contamination.

Lipofuscin is indigestible garbage that accumulates in the autophagic vesicles and cytosol of post-mitotic cells with age. Drs. Brunk and Terman postulated that lipofuscin accumulation is the main or at least a major driving factor in aging. They even posited that the evolution of memory is the reason why we get lipofuscin at all, as stable synaptic connections must be maintained over time, meaning that the somas of neurons must also remain in the same locale. In other words, they cannot dilute out their garbage over time through cell division. Mechanistically, their position certainly makes sense given that rendering a large percentage of a post-mitotic cell’s lysosomes useless must almost certainly negatively affect that cell and the surrounding microenvironment. Here, I explore the possibility that the accumulation of lipofuscin may to some extent exacerbate every other kind of age-related damage. I do not think that lipofuscin removal will reverse/prevent all forms of aging, just the major component facing us currently. In this piece, I will review what is known about lipofuscin accumulation from evolutionary and mechanistic standpoints and discuss a method of removing it from single cells in vitro.

A body plan is a stable configuration of characters for a major taxonomic group, such as chordates or arthropods. Despite widespread casual reliance on the concept for guiding comparisons within and between groups, the nature of body plans as well as the biological causes underlying their evolution have remained elusive. This paper proposes an abstract mechanistic model of body plan identity. We hypothesize that body plans are an evolutionary phenomenon that only applies to a relatively small subset of major clades, rather than being associated with each and every so-called “phylum.” Body plans arise in evolution by stepwise accretion, and require a level of developmental complexity that is only found in some animal clades. Further, we suggest that, parallel to the developmental mechanisms controlling character identity, there are “body plan identity mechanisms” (BpIMs) that maintain entire configurations of characters while possessing a mechanistic architecture that is itself stable and traceable through evolutionary change. These BpIMs, we suggest, are entrenched intercellular signaling networks operating between transient embryonic structures that are destined to differentiate into distinct individualized characters. The activity of a BpIM results in a transient long-range integration of the embryo that is highly sensitive to genetic and environmental perturbations, and that can be detected morphologically as a conserved phylotypic stage. This model is illustrated with detailed interpretations of the notochord signaling system and the segment polarity network as candidate BpIMs in vertebrates and arthropods, respectively. We conclude by contrasting the proposed developmental-mechanistic conception of body plans with the phylogenetic notion of ground plans, and sketch the general outlines of an empirical research program on body plan evolution.

Recent improvements in deepfake creation have made deepfake videos more realistic. Moreover, open-source software has made deepfake creation more accessible, which reduces the barrier to entry for deepfake creation. This could pose a threat to the people’s privacy. There is a potential danger if the deepfake creation techniques are used by people with an ulterior motive to produce deepfake videos of world leaders to disrupt the order of countries and the world. Therefore, research into the automatic detection of deepfaked media is essential for public security. In this work, we propose a deepfake detection method using upper body language analysis. Specifically, a many-to-one LSTM network was designed and trained as a classification model for deepfake detection. Different models were trained by varying the hyperparameters to build a final model with benchmark accuracy. We achieved 94.39% accuracy on the deepfake test set. The experimental results showed that upper body language can effectively detect deepfakes.

The usual equation for both motions of a single planet around the sun and electrons in the deterministic Rutherford-Bohr atomic model is conservative with a singular potential at the origin. When a dissipation is added, new phenomena appear which were investigated thoroughly by R. Ortega and his co-authors between 2014 and 2017, in particular all solutions are bounded and tend to $0$ for $t$ large, some of them with asymptotically spiraling exponentially fast convergence to the center. We provide explicit estimates for the bounds in the general case that we refine under specific restrictions on the initial state, and we give a formal calculation which could be used to determine practically some special asymptotically spiraling orbits. Besides, a related model with exponentially damped central charge or mass gives some explicit exponentially decaying solutions which might help future investigations. An atomic contraction hypothesis related to the asymptotic dying off of solutions proven for the dissipative model might give a solution to some intriguing phenomena observed in paleontology, familiar electrical devices and high scale cosmology

This review paper investigates the intricate relationship between sexuality and body dysmorphia, emphasizing its profound impact on mental health. Through a critical examination of existing literature, this study illuminates the complex psychological, societal, and cultural dynamics at play within this intersection. Special attention is given to the influence of media representations and societal beauty standards in shaping individual perceptions and experiences. Furthermore, the paper discusses various therapeutic interventions designed to address this interplay, underscoring the necessity for mental health practices that are both sensitive and adaptable to the nuances of these issues. Ultimately, this work enriches the discourse on body image and sexual health, offering critical insights for clinical interventions and highlighting areas for further research.

Three body systems in which one of the bodies is ejected without escaping the binary system have previously been studied in various restricted forms. However, none of these studies dwells on the problem in a general setting. Thus, to study this phenomenon qualitatively, we try to expand this problem's scope to unequal mass systems and generalize them by considering various configurations of fixed initial points with precisely calculated initial velocities, some zero velocity models and some optimized models. We will see the use of terminology similar to the previous studies done in this domain but incorporate different analytical and evaluation methods.

Inspired by amazing result obtained by Semay [1], this study revisits generalised Kepler's third law of an n-body system from the perspective of dimension analysis. To be compatible with Semay's quantum n-body result, this letter reports a conjecture which had not be included in author's early publication [2] but formulated in the author's research memo. The new conjecture for quantum N-body system is proposed as follows: Tq|Eq|^3/2 = πG/√2[(Σ^N_i=1 Σ^N_j=i+1 m_im_j)³/(Σ^N_k=1 m_k)]^1/2. This formulae is, of course, consistent with the Kepler's third law of 2-body system, and exact same as Semay's quantum result for identical bodies.

What drives an individual police officer to activate his body-worn camera (BWC)? Some evidence suggests officer attitudes and resistance to the technology contributes to the equivocal results in studies testing for BWCs effect on use-of-force, complaints, and other outcomes of interest. Leveraging a novel survey and administrative dataset, we investigate the predictors of BWC activation among 147 police officers in a single agency. With a test of three nested models, we find job function covariates offer robust predictive power of how often an officer activates her or his BWC. Neither demographic nor attitudinal measures significantly predict BWC activations, except for a negative relationship with how officers perceive BWC impacts on professional discretion. The study furnishes empirical support for understanding officers as Principled Agents: job function, guided by administrative policy is the most explanatory and parsimonious, while models of attitudes and demographics fail to improve upon the job function model.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

Nanomagnetism and spintronics are currently active areas of research, with one of the main goals being the creation of low-energy-consuming magnetic memories based on nanomagnet switching. These types of devices could also be implemented in neuromorphic computing by crafting artificial neurons (ANs) that emulate the characteristics of biological neurons, through the implementation of neuron models such as the widely used leaky integrate-and-fire (LIF) with a refractory period. In this study, we have carried out numerical simulations of a 120 nm diameter, 250 nm length ferromagnetic nanowire (NW) with the aim of exploring the design of an artificial neuron based on the creation and destruction of a Bloch-point domain wall. To replicate signal integration, we applied pulsed trains of spin-currents to the opposite faces of the ferromagnetic NW. These pulsed currents (previously studied only in the continuous form) are responsible for inducing transitions between the stable single vortex (SV) state to the metastable Bloch point domain wall (BP-DW) state. To ensure the system exhibits the leak and refractory properties, the NW was placed in an homogeneous magnetic field of the order of mT in the axial direction. The suggested configuration fulfills the requirements and characteristics of a biological neuron, potentially leading to the future creation of Artificial Neural Networks (ANNs) based on reversible changes in the topology of magnetic NWs.

Gut microbiota affects progression of rheumatoid arthritis (RA). The present study aims at investigating the protective potential of Bifidobacterium longum cell wall lipoproteins (Lpps) shown to modulate the intestinal microbiome and prevent osteoarthritis. Arthritis was induced by collagen (CIA) or anti-collagen antibodies (CAIA) injection. Intake of 0.5 mg Lpps /L, but not 0.25 and 1mg Lpps/L significantly alleviated RA symptoms in CIA DBA/1OOaHsd mice. Arthritis index (AI) was also reduced in CAIA mice. In CIA protected group, colon Ligilactobacillus murinus, caecal Lactobacillus johnsonii and spleen weight correlated with AI, whereas the reverse was observed with splenic CD11c+ dendritic cells (cDCs). The unprotected CIA Lpps group harbored higher caecal and colon E. coli and lower caecal L.murinus. Lpps administration to CAIA mice after arthritis induction led to lower colon E. plexicaudatum counts. Splenocytes from CIA protected mice triggered by LPS secreted higher Il-10 than control ones. However, higher IL-10 response was not elicited in gnotobiotic RA mice splenocytes with lower cDCs recruitment. Labeled bacteria with Lpps signal were detected in CIA mice bone marrow (BM) cDCs 5 and 16h post-gavage but not in Peyer’s patches and spleen. In vitro uptake of Lpps by primary BM and thymus cells was observed within 24h. FACS analysis detected the Lpps signal in the plasmacytoid cell compartment but not in cDCs. In conclusion, Lpps dosing is critical for preventing arthritis progression and appropriately modulating the microbiome. Our results also highlight the possible triggering of the immune system by Lpps.

Quasistatic nanoindentation is a proven tool that provides information on the micromechanical behavior of wood cell walls. However, quasistatic tests cannot probe the time-dependent mechanical behavior shown by wood. Nanoindentation dynamic mechanical analysis (nanoDMA) can mesaure the viscoelastic properties of wood cell walls. This research aimed to study the quasistatic and viscoelastic properties of individual radiata pine wood (Pinus radiata D. Don) cell wall layers. To minimize variability and retrieve both properties at the same locations, a load function composed of a multiload-quasistatic function followed by dynamic reference frequency segments was developed. Nanoindentations were then performed on the S2 layer and compound corner middle lamella (CCML) of unembedded latewood cells. Because the S2 layer is anisotropic, both transverse and longitudinal-tangential wood planes were studied. In the transverse plane, the average results of the quasistatic elastic moduli (Es) for the S2 layer and CCML were 15.7 GPa and 4.6 GPa, respectively. In the longitudinal-tangential plane, the E_s was 3.9 GPa. In the transverse section, the hardness (H) of the S2 layer and CCML were 331 MPa and 277 MPa, respectively, and in the longitudinal-tangential section H was 244 MPa. To acquire the viscoelastic properties, measurements were made over more than three decades of frequency. An increase of the storage modulus (E'), and a reduction of the loss modulus (E'') and loss factor (tan⁡ δ ) as frequency increased were found in both wood orientations. The quasi-static and dynamic indentations equivalent at 0.1 Hz showed similar values for Es and E’. This study contributes to our knowledge of wood cell wall micromechanical properties.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Domain walls were studied for permalloy wires with different depth trenches (500 nm wide, 30 nm thick, 7.5 µm long, the depth of the trench was 0, 4, 5, 8, 10, 12 and 15nm). Permalloy (Ni80Fe20) wires were fabricated by electron beam lithography and Ar ion milling. When the depth of trench is smaller than 12 nm, the switching field (Hs) is increasing with the deeper trench. However, the depth of trench is bigger than half depth of thickness, the Hs is decreasing with the deeper trench. We believed that Hs increased as the trench depth increased was because the magnetic diploes force increased between the magnetic poles on two sides of the trench. The domains of the wires were divided by the trenches and the domain walls were pinned on the trenches these were confirmed by magnetic force microscopy images.

Watermelon fruits of different ploidy exhibit significant variations in texture. In order to investigate the primary factors influencing texture differences, this study was conducted to investigate the differences in fruit texture development using homozygous autogamous diploid (2X)lines and their autotriploid (3X) and autotetraploid (4X) lines 'Yixuan'. The research encompassed fruit development, flesh texture profile analysis (TPA), flesh cell wall polysaccharide content, and flesh cell microstructure analysis, specifically in 2X, 3X, and 4X watermelon fruits.The results showed that as watermelon fruits matured, several characteristics exhibited an ascending trend, including fruit weight, TSS (total soluble solids) content, rind hardness, flesh cell size, and cell wall polysaccharide contents such as crude fiber, cellulose, hemicellulose, lignin, and protopectin. Conversely, the flesh texture parameters and soluble pectin content of the flesh cell wall gradually declined. Notably, significant differences in fruit flesh texture and flesh cell structure were observed among fruits of different ploidy at the 32d. Specifically, 2X fruits displayed considerably lower rind hardness, reduced flesh texture (Hardness, Fracturability, Chewiness, Gumminess), and cell density compared to 3X and 4X fruits. Additionally, 2X fruits exhibited larger cell sizes than 3X and 4X fruits. However, no significant differences were observed in the content of flesh cell wall polysaccharide contents across various ploidy levels.These findings suggested that the variation in texture among watermelon fruits of different ploidy can be attributed to the size and arrangement of flesh cells. Importantly, this research provided a foundation for further exploration of the intrinsic regulatory factors and molecular mechanisms contributing to texture variation in polyploid watermelon fruits.

Some biologically active compounds isolated from sea cucumbers stimulate the body’s immune response through activating immune cells. Immune function is closed related to the integrity intestinal barrier and balanced gut microbiota. However, it is unknown whether daily administration of holothurian wall hydrolysates (HWH) ameliorated intestinal dysbiosis and barrier injury induced by immunodeficiency. This study aimed to investigate the immunomodulatory effect and the underlying mechanism of HWH in cyclophosphamide (CTX)-induced immunocompromised mice. BALB/c mice received CTX (80 mg/kg, intraperitoneally) once a day for 3 days to induce immunodeficiency, and then oral administration of HWH (80 or 240 mg/kg), levamisole hydrochloride (LH, 40 mg/kg, positive control) respectively once a day for 7 days. We utilized 16S rRNA sequencing for microbial composition alterations, histopathological analysis for splenic and colonic morphology, Western blotting for expressions of tight junction proteins (TJs), and quantitative real-time (qRT-PCR) for measurements of pro-inflammatory cytokines. HWH attenuated the immune organ damage induced by CTX, increased the secretions of interleukin (IL)-6, IL-1β and tumor necrosis factor (TNF)-α, and promoted the recovery of goblet cells and the productions of TJs (claudin-1, occludin, and ZO-1) in the colon of the immunocompromised mice. Moreover, HWH promoted the growth of beneficial microorganisms such as Lactobacillus, Lachnospiraceae, Christensenellaceae, and Bifidobacterium, while suppressed the populations of Ruminococcus, Staphylococcus, and Streptococcus. These results demonstrate that HWH elicits intestinal mucosal immunity, repairs the damage to intestinal mucosal integrity, and normalizes the imbalanced intestinal microbial profiles in immunocompromised mice. It may be helpful to identify the biological activities of HWH, and supports the potential as new prebiotics, immunomodulatory agents, and medical additive for intestinal repair.

The geographic variability of the dorsal pattern (DP) of the Italian wall lizard, Podarcis siculus, across its native range was studied with the aim to understand whether the distributions of this phenotypic trait were more shaped by allopatric differentiation rather than adaptive processes. A total of 1298 georeferenced observations scattered across the Italian peninsula and the main islands (Sicily, Corsica and Sardinia) were obtained from citizen science databases and five DPs were characterized by different shapes of the dark pattern (“reticulated”, “campestris”, “reticulated/campestris” and “striped”) or by absence of it (“concolor”). Frequencies of different DP phenotypes differ between the two main mtDNA lineages settled in central-northern and in southern Italy respectively. This pattern may be indicative of a role of long-term allopatric historical processes in determining the observed pattern. The analysis also identified a putative wide area of secondary contact, in central southern Italy, characterized by high diversity of the DP. Generalized Linear Models (GLMs), used to estimate a possible association between bioclimatic variables and the observed phenotypic variation, showed that each of the five DPs is correlated to different environmental factors and show different distribution of areas with high probability of occurrence. However, for all but one of the DPs, the area with the greatest probability does not correspond exactly to the real distribution of the DP. Conversely, the “concolor” phenotype does not seem related to any particular mtDNA lineage and it shows a preference for areas with high temperature and low rainfall. This is in agreement with the expectation of low amount of melanin of the dorsal pattern that, in the study areas, is characterized by a light uniform coloration which could confer a better thermoregulation ability in high temperatures environments avoiding overheating.

Heart myocardia are critical to the facilitation of heart pumping and blood circulating around the body. The biaxial mechanical testing of the Left Ventricle (RV) is utilised to build the computa-tional model of the whole heart with little importance given to the unique mechanical properties of Right Ventricle (RV) and Mid-wall (MDW). Most of those studies focussed on the LV of the heart, and then apply the obtained characteristics with a few modifications to the right side of the heart. However, that view has been contested over time with the realisation that the right side of the heart possesses its own unique mechanical properties that are widely distinct from that of the left side of the heart. This paper is aimed at reporting and evaluating the passive mechanical property dif-ferences in the three main walls of the rat heart based on biaxial tensile test data. Fifteen mature Wistar rats weighing 225 ± 25 g were euthanised by inhalation of 5 % halothane. The hearts were excised after which all the top chambers comprising the two atria, pulmonary and vena cava trunks, aorta and valves are all dissected out. Then 5 x 5 mm sections from the middle of each wall were carefully dissected with a surgical knife to avoid over-prestraining the specimens. The specimens were subjected tensile test. The elastic moduli, peak stresses in the toe region and stresses at 40 % strain, anisotropy indices as well as the stored strain energy in the toe and linear region up to 40 % strain are used for statistical significance tests. The following are the main findings of this study: (1) LV and MDW tissues have relatively shorter toe regions of 10 - 15 % strain as compared to RV tissue whose toe region extends up to twice as much as that (2) LV tissues have higher strain energy storage in the linear region despite being lower in stiffness than the RV (3) the MDW has the highest strain energy storage along both directions which might be directly related to its high level of anisotropy. These findings, though for a specific animal species at similar age and around the same body mass, emphasize the importance of application of wall specific material parameters to obtain accurate ventricular hyperelastic models. The findings further enhance our understanding of the desired mechanical behaviour of the different ventricle walls.

The usual equation for both motions of a single planet around the sun and electrons in the deterministic Rutherford-Bohr atomic model is conservative with a singular potential at the origin. When a dissipation is added, new phenomena appear. It is shown that whenever the momentum is not zero, the moving particle does not reach the center in finite time and its displacement does not blow-up either, even in the classical context where arbitrarily large velocities are allowed. Moreover we prove that all bounded solutions tend to $0$ for $t$ large, and some formal calculations suggest the existence of special orbits with an asymptotically spiraling exponentially fast convergence to the center.

The aim of the study was to evaluate the influence of transduser design and its elements, and their materials on temperature in deeper layers of tissues measurement results. A digital modeling was performed to evaluate the influence of the properties of transduser design elements. Experimental research was carried out. Revealed that the accuracy, similar to that of an invasive method using needle probes, can be achieved by measuring the temperature in deeper muscle layers using the proposed transducer.

The centrifugal force field in the hydrocyclone was affected by the concave-wall curvature radius R0, the mechanism of droplet deformation was closely related to the mass transfer efficiency. Numerical simulation and experimental data were collected to reveal the deformation characteristics and mechanism of single droplet crossing concave-wall jet. Normalized interfacial energy γ and stretching performance were provided to investigate the droplet deformation process. The results showed that the droplet was stretched along the streamwise and shrank along the spanwise in the concave-wall jet. The droplet interfacial energy and deformation were the largest when the droplet crossed the jet boundary at t = 0.20 s. Maximum γ value increased with the increase of R0 by 57.3% to 71.4%, and the distance between droplet and concave-wall increased with R0. Q-criterion was exported to show the vortex strength increasing as the decrease of R0 in the jet boundary. The pressure distribution inside the droplet showed that the pressure decreased as R0 increased, while the pressure difference increased along the streamwise and wall-normal direction. The study suggested that the droplet breakup was more difficult for the smaller R0, which was beneficial for liquid-liquid heterogeneous separation.

As the control brain of the petrochemical plant, blast resistant performance requirements of the petrochemical control room should be guaranteed when the vapor cloud explosion occurs in the petrochemical production process. 3D-Kagome truss core sandwich structure is a kind of blast resistant material with high energy absorption. Considering the influence factors of the radius of the truss core rod and thickness of the upper and lower panels, in this paper, blast resistant performance of a real steel petrochemical control room with 3D-Kagome truss core sandwich wall is analyzed. With the optimization goal of plastic deformation energy and panel displacement, the optimal wall thickness and radius of the truss core rode are obtained. The optimized blast resistant wall is assembled, and the dynamic response of the steel petrochemical control room with the 3D-Kagome truss core sandwich blast resistant wall is analyzed. The simulation results show that the truss core layer does not dissipate the blast energy effectively when the radius ratio of the truss core rod is larger than 2.7% of the total thickness of the wall; with the increase of the thickness of the upper and lower panels, the proportion of plastic deformation energy of the truss core layer increases gradually and then tends to be a stable proportion value, that is about 90%; When the thickness ratio of the panel is 6.7% of the total one of the wall and the radius ratio of the truss core rod is 2.7% of the total thickness of the wall, the optimal blast resistant 3D-Kagome sandwich wall is determined.

In order to study the collapse failure of shaft wall of high depth inclined ore-pass under ore impact wear behavior, 25 ore-passes in a deep mine in Yunnan, China were investigated. Considering the ore-pass structural characteristics and the impact wear effect of ore on shaft wall, the shaft wall damage model of high depth inclined ore-pass is constructed based on the contact mechanics theory. Furthermore, No. 1#, 2#, 3# and 9# ore-passes of the mine are taken as examples for analysis, and the three results of theoretical analysis, numerical simulation and engineering case are used for comparison and verification. The shaft wall damage degree is predicted, and the damage mechanism between total shaft wall damage volume Qtol and ore-pass depth H, ore-pass dip angle θ, inclined angle of chute α, shaft diameter D and ore block size P is quantitatively investigated. The results show that the rationality of the proposed model is verified by numerical analysis and field engineering situations. Moreover, the deeper ore-pass depth H, the more shaft wall damage volume Qtol with the increase of collision frequency. Qtol increases exponentially with P and increases gradually with D. With the increase of θ or α, Qtol increases generally first and then decreases. Therefore, Qtol can be effectively reduced by selecting the appropriate structure parameters of ore-pass and adopting the technology of drilling straight ore-pass. This work provides technical support for long period safe operation of high depth inclined ore-pass.

Modular high-rise buildings frequently adopt cast-in-place concrete to ensure building integrity. To reduce the material consumption and realize mold-free casting, a 30 mm thick light concrete mold shell wall panel ( MiC wall panel) is set as part of the shear wall. But the concrete casting process is prone to cracking and rising pattern. Its force performance and damage mechanism is not clear. To this end, this paper designs three groups of MiC wall panels with different material component types. The static load test is carried out in a graded partitioned loading mode. The effects of different material components on the mechanical properties of MiC wall panels are systematically investigated and parametrically analyzed by numerical simulation. The results show that the front cracks of the wall slab are mainly distributed under the truss tendons, and the back cracks are mainly distributed in the span position of the adjacent truss tendons. They are both along the span direction of the wall slab. Increasing the strength level of concrete and using steel fiber concrete can improve the mechanical properties of MiC wall panels to different degrees. Among them, increasing the concrete strength has a significant effect on improving the load-bearing capacity of wall panels, while incorporating steel fibers can significantly improve the deformation and crack resistance of wall panels. By building more finite element models, it was verified that the steel fiber admixture has limited effect on the mechanical properties of wall panels as the concrete grade increases. This study aims to summarize the types of wall panels with the best working properties. It provides a practical basis for optimizing the production and fabrication process of MiC wall panels.

This study provides a contribution to the research field of 3D printed earthen buildings, focusing, for the first time, on the load-bearing capacity of these structures. The study involves the entire production and testing process of the earthen elements, from design, to the preparation of the mixture and the 3D printing, up to the uniaxial compression test on a wall segment. The results indicate that 3D printed earthen elements have a compressive strength of 2.32 MPa, comparable to that of rammed earth structures. The experimental data also made it possible to draw conclusions on the action of the infill, which seems to have the function of stopping the propagation of cracks. This has a positive effect on the overall behavior of 3D printed earthen elements, since it avoids the onset of dilative behavior in the final stages of the load test and maintains ultimate load values higher than 50% of the maximum load.

A new lateral force-resisting wall panel is presented for applications in mid-rise prefabricated lightweight steel construction in seismic prone regions. This panelised system is composed of a hot-rolled frame and cold-formed studs and tracks, which works as a lateral force resisting system in lightweight steel framing. The proposed hybrid panel system exhibits proper ductility and energy dissipation behaviour. The hysteretic responses of full-scale panel experiments demonstrate that the system can safely resist high cyclic loads. The hot-rolled steel part, on the other hand, can significantly improve the initial lateral stiffness of the total system that will control the maximum allowable drift of multi-story buildings. Finally, in a case study, by applying the proposed system to the design of a mid-rise building in a high seismic area, the performance of the hybrid panels, are compared with those of fully hot-rolled systems (moment resisting frames) and fully cold formed systems. The findings indicate that applying hybrid panels will result in lower weights and better performance in seismic prone regions.

We report the growth of graphene at a low temperature using the cold wall chemical vapor deposition technique (CWCVD). Few layered (~6-8 layers) graphene were grown on nickel-coated silicon with acetylene as the precursor gas. The advantage of the combination of the acetylene (as a carbon feedstock) and the nickel catalyst was the lowering of the graphene growth temperature. Nickel coated silicon samples were pre-treated (heat treatment in inert atmosphere) before the growth and the effect of the pre-treatment on the catalyst as well as on the grown film was studied. The final samples were characterized with scanning electron microscopy and Raman spectroscopy. In CWCVD route, the heating of only the substrate holder enabled high heating and cooling rates, which, along with the control over partial pressure of the precursor gas had profound effect on the formation of graphene. In the best sample we have achieved almost equal intensity of the G and 2D peaks in Raman spectrum, which implied about ~6-8 layers of Graphene. The defect peak (the D band) was extremely small in the sample and it was attributed to the ripples and the underlying roughness of the nickel film. We analyzed that a proper choice of the thickness of catalyst layer and a higher cooling rate after graphene growth it would be possible to obtain monolayered graphene. Similar samples grown in a normal atmospheric CVD (with some engineered design to promote fast cooling) were also compared with the cold wall CVD grown samples and plasma assisted CWCVD, and cold-wall CVD demonstrated a better control over the quality of graphene film through the fast cooling and a controlled partial pressure of the precursor gas.

Our study focused on investigating the impact of Instagram use on body satisfaction and self-esteem among participants aged 20 to 40 years (N = 95) through a cross-sectional survey design in which the Rosenberg Self-Esteem Scale, the Body Shape Questionnaire (BSQ), and ad hoc designed questions were administered. The results highlight the influence of Instagram on body dissatisfaction (p = .005) but not on self-esteem (p = .211). Gender was not found to be an influential factor (p = .173). However, it was found that greater body satisfaction correlates with higher self-esteem and vice versa (p < .001). Finally, we concluded that the number of hours users in the sample spend on Instagram is related to greater body dissatisfaction but not to lower self-esteem.

To analyze the combined response of ocular cyclotorsion and head tilt during body tilt and to interpret the physiologic role of those movements, each of the three subjects completed six different experiments of body tilt not fixating their head movements using a flight simulator, which consisted of combinations of three tilt angles (30, 45, and 60) and two visual conditions. Head tilt and ocular cyclotorsion of the right eye before, during, and after the tilt maneuver were recorded and analyzed by time sequence. In the active tilting phase, the right eye showed a stepladder pattern of multiple repeats of fast and slow cyclotorsion along with head tilt to obtain maximum visual information. During the stationary tilting phase, there occurred a small amount (mean, 2.3) of ocular cyclotorsion which was reciprocal to that of head tilt. The visual cue of body tilt through the central visual field induced a larger amount of head tilt but affected little ocular cyclotorsion. The maximum degree of ocular cyclotorsion during each experiment was 10.2 on average. In conclusion, the combined response of ocular cyclotorsion and head tilt develops during body tilt and it compromises the conflicting needs between binocular vision and gravitational orientation.

Dietary intake and alcohol consumption might be influenced by genetic variations in taste receptor genes. The objectives of this study were to examine the relationship between polymorphisms in bitter taste receptor genes TAS2R13 (rs1015443) and TAS2R38 (rs1726866, rs10246939, and rs713598) as well as alcohol consumption and body fat percentage in college students. Four hundred and two students with a mean age of 20.2 years participated in this study. An NIH Diet History Questionnaire (DHQ II) was used to collect data on their dietary intake, while AUDIT survey was used to determine their level of alcohol consumption. Bitter taste receptor gene polymorphisms were assessed by TaqMan allelic discrimination assays. Despite significant associations between TAS2R13 (rs101544) and certain aspects of alcohol consumption, including the frequency of alcohol intake, no indeed significant associations were found between TAS2R13 (rs1015443) and alcohol consumption after accounting for confounding variables in the regression model. Neither association was found regarding percent of body fat. In contrast, ethnicity and gender significantly influenced percent of body fat (p < 0.001), while no significant association was observed between TAS2R13 (rs1015443) and percent of body fat. Likewise, TAS2R38 (rs1726866, rs10246939 and rs713598) demonstrated no significant association with alcohol consumption and percent of body fat. These results were controlled for confounding factors, such as ethnicity and gender. Body fat percentage and alcohol consumption may be influenced by ethnicity, gender and age rather than SNPs of TAS2R13 and TAS2R38 genes. Assessing the taste genes’ interactions with diet and body composition might be useful in identifying human disease risk.

TThe passion of bodybuilding athletes for a symmetric, lean, heavily muscled body leads them to carry out exhausting exercise programs and restrictive eating regimens, sometimes resulting in disordered eating behaviors. This study investigates potential exacerbators on the development of disordered eating in bodybuilding and strength athletes. The study involved 103 Cypriot bodybuilding athletes of both sexes, performing at three levels: professional, recreational and strength athletes. The Eating Attitude Test 26 (EAT-26) and The Three Factor Eating Question-naire (TFEQ-R21) were used to evaluate disordered eating and eating behaviors respectively. The current study was performed under the auspices of the Hellenic Center of Education & Treatment of Eating Disorders (KEADD). The degree of deviation between the perceived ideal body weight and the actual body weight was associated with increased risk of eating disorder. Athletes who desired a lower body weight recorded higher scores on EAT-26 overall, (p=0.001), and the subscales of dieting (p=0.01) and bulimia. (p=0.001). Cognitive restraint and emotional eating scales of TFEQ-R21 were more pronounced in the non-professional athletes. (p=0.01). The emotional eating score was higher in women. There is a need for appropriate sport-specific, gender-specific preventive intervention to deescalate the risk of eating disorder, in both profes-sional and non-professional bodybuilding athletes.

The magnetic field of the earth plays an important role in the ecosystem, and the magnetic field of celestial bodies is also important in the formation of cosmic large-scale structures, but the origin and evolution of the celestial magnetic field is still an unresolved mystery. Many hypotheses to explain the origin have been proposed, but there are some insurmountable difficulties for each one. At present, the theory widely accepted in scientific society is the dynamo model, it says that, the movement of magnetofluid inside celestial bodies, which can overcome the Ohmic dissipative effect and generate persistent weak electric current and macroscopic magnetic field. However, this model needs an initial seed magnetic field, and the true values of many physical parameters inside the celestial body are difficult to obtain, and there is no stable solution to the large range of fluid motion. These are all difficulties for the dynamo model. Furthermore, it is difficult for the dynamo to explain the correlation between the dipole magnetic field and angular momentum of a celestial body. In this paper, by calculating the interaction between spin of particles and gravity of celestial body according to Clifford algebra, we find that a rotational celestial body provides a field $\Omega^\alpha$ for spins, which is similar to the magnetic field of a dipole, and the spins of charged particles within the celestial body are arranged along the flux line of $\Omega^\alpha$, then a macroscopic magnetic field is induced. The calculation shows that the strength of $\Omega^\alpha$ is proportional to the angular momentum of the celestial body, which explains the correlation between the magnetic intensity and angular momentum. The results of this paper suggest that further study of the effects of internal variables such as density, velocity, pressure and temperature of a celestial body on $\Omega^\alpha$ may provide some new insights into the origin and evolution of celestial magnetic field.

There are no studies that quantitatively compare life histories among scorpion species. Statistical procedures applied to 94 scorpion species indicate that those with larger bodies do not necessarily have larger litters or longer life cycles, opposite to some theoretical predictions.

The Krudum granite body comprises highly fractionated granitic rocks ranging from medium-F biotite granites to high-F, high-P₂O₅ Li-mica granites. This unique assemblage is an ideal site to continue recent efforts in petrology to characterize the role of zircon, monazite and xenotime as hosts to REEs. The granitic rocks of the Krudum body analysed in this study were found to contain variable concentrations of monazite and zircon, while xenotime was only found in the high-F, high-P₂O₅ Li-mica granites and in the alkali-feldspar syenites of the Vysoký Kámen stock. For analysed monazites of all magmatic suites cheralite substitution was significant. The highest concentration of cheralite was found in monazites from the high-F, Li-mica granites and from the alkali-feldspar syenites. The proportion of YPO₄ in all analysed xenotimes ranges from 71 to 84 mol. %. Some xenotimes were found to be hydrated and the observed water content estimated from analytical data ranged from 5 to 11 wt. % H₂O. Analysed xenotimes were commonly enriched in HREEs (9.3– 19.5 wt. % HREE₂O₃) and thorite-coffinite and cheralite exchange was observed. Analysed zircons from granite suites of the Krudum granite body contained moderate Hf concentrations (1.0–4.7 wt. % HfO₂; 0.010–0.047 apfu Hf). The highest concentrations of HfO₂ were found in zircons from the high-F, high P₂O₅ Li-mica granites (1.2–4.7 wt. % HfO₂) and from the alkali-feldspar syenites (1.3–4.1 wt. % HfO₂). Zircons from the high-F, high-P₂O₅ Li-mica granites were often hydrated and fluorised. The concentrations of F in zircon from partly greisenised high-F, high-P₂O₅ Li-mica granites reached up to 1.2 wt. % (0.26 apfu F). In zircons from the alkali-feldspar syenites enrichment in P, which is not associated with a simultaneous enrichment in Y + REE, was also observed. Analysed zircons from the high-F, high P₂O₅ Li-mica granites were enriched in Y (up to 5.5 wt. % Y₂O₃; 0.10 apfu Y) and Sc (up to 1.17 wt. % Sc₂O₃; 0.03 apfu Sc).

Psychological wellbeing can be impacted substantially by changes in body image during youth, which can be a predictive factor for positive or negative attitudes, such as for self-esteem and satisfaction. In this study, adherence to the thinness model and to healthy behaviours were analysed in terms of the emotional patterns and body management of the young female Italian population (N = 2287). Skinny girls fitting better with the thinness model tended to develop higher positive emotional patterns, but their body management was low. Findings suggest the urgent need for preventive programmes to enhance awareness of healthy behaviours against appearance models.

Introduction: Desmoid tumor (DT) is a rare benign neoplasm rising from muscle aponeurosis, having been associated mostly with trauma or pregnancy. DT has an infiltrative and locally aggressive growth pattern and usually does not metastasize. However, it has a high recurrence and complication rate. When they occur in pregnancy, are all pregnancies and deliveries taken as individual case for optimal management by the physicians and midwifes, who need to be cautious in finding the optimal delivery mode for patients, which depends on tumor size, location, behavior and past history. Study Objectives: We present a case report of a large desmoid tumor of the anterior abdominal wall in a 29-year-old woman in pregnancy, presenting a delivery problem, which resolved in surgical management. Moreover, we are bringing a systematic review of the literature to provide an overview on pathomechanism, symptoms, diagnostics and treatment management of the pregnant women affected by DT. Results: The authors report a case of pregnant women who underwent systemic oncological treatment for abdominal wall desmoid tumor and have been pregnant afterwards. The observational conservative management was chosen with an elective cesarean section at the 38+4 pregnancy week with uncomplicated postpartum follow-up. Conclusion: Pregnancy-associated desmoid tumors are very rare and optimal management of this tumor is not well established, despite some guidelines for non-pregnant patients. The authors reviewed the literature focusing on the actual modern management of desmoid tumors at all, including patients during the pregnancy, as well.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

This article presents raw data of biaxial tensile measurements of rat heart passive myocardium conducted in lab scale environment. The passive myocardium of the rat was divided into three regions, namely: left ventricle, mid-wall and right ventricle. The biaxial dataset of passive rat myocardia is presented as stress vs strain of the passive rat myocardium in various regions. The determination of valid material properties of the heart plays an important role in the development computational models. These computational models are useful in studying various scenarios and mechanisms of heart diseases. In addition, valid and accurate materials are critical in the development of new therapies. The dataset presented here is useful in the area of soft tissue mechanics including studying the mechanisms of heart diseases such as myocardial infarction. Accordingly, the evaluation of stress and strain in left ventricle, mid-wall and right ventricle was performed.

.Functionalization of multi-walled carbon nanotubes (MWNTs) surface with sulfonated poly(ether ether ketone) SPEEK chains using hexane diamine (HAD) as the interlinking molecule was investigated. MWNTs were first oxidized by nitric acid to generate carboxyl groups on their surface. Grafting of SPEEK chains on the MWNTs surface was achieved using hexane diamine as a cross-linking molecule. The attachment took place after the reaction of amine groups with carboxyl groups of oxidized MWNTs and sulfonate groups of SPEEK as confirmed by infrared (FTIR) analysis. Scanning electron microscopy (SEM) showed that MWNTs were packed into a dense and compact structure. Transmission electron microscopy (TEM) showed that the nanotubes were wrapped by polymer chains and arranged in a bundle like structure. These observations reveal that some of MWNTs were interconnected by SPEEK chains.

Colletotrichum higginsianum is a major pathogen causing anthracnose in Chinese flowering cabbage (Brassica parachinensis), posing a significant threat to the Chinese flowering cabbage industry. The conidia of C. higginsianum germinate and form melanized infection structures called appressoria, which enable penetration of the host plant's epidermal cells. However, the molecular mechanism underlying melanin biosynthesis in C. higginsianum remains poorly understood. In this study, we identified two enzymes related to DHN-melanin biosynthesis in C. higginsianum: ChPks and ChThr1. Our results demonstrate that the expression levels of genes ChPKS and ChTHR1 were significantly up-regulated during hyphal and appressorial melanization processes. Furthermore, knockout of the gene ChPKS resulted in a blocked DHN-melanin biosynthetic pathway in hyphae and appressoria, leading to increased sensitivity of the ChpksΔ mutant to cell wall interfering agents as well as decreased turgor pressure and pathogenicity. It should be noted that although the Chthr1Δ mutant still exhibited melanin accumulation in colonies and appressoria, its sensitivity to cell wall interfering agents and turgor pressure decreased compared to wild-type strains; however, complete loss of pathogenicity was not observed. In conclusion, our results indicate that DHN-melanin plays an essential role in both pathogenicity and cell wall integrity in C. higginsianum. Specifically, ChPks is crucial for DHN-melanin biosynthesis while deficiency of ChThr1 does not completely blocked melanin production.

Background: Globally, about 3.5 billion people are affected by intestinal parasitic infections (IPIs). This study aimed to investigate the effects of IPIs on intestinal wall thickness and its potential association with hypertension in different genders. Methods: A total of 108 subjects, including 83 consecutive patients with symptomatic and laboratory-confirmed IPIs (male = 48; female = 35) and 25 healthy controls (male = 10; female = 15), were recruited. B-mode ultrasound grayscale and color images of the duodenum and colon were obtained with and without water contrast. Results: Patients with IPIs had a tendency towards greater duodenal wall thickness (DUOTHICK = 0.88 ± 0.73 cm) compared to controls (0.595 ± 0.089 cm), p = 0.056. Patients with IPIs also had significantly greater ascending colon wall thickness (ASCTHICK = 1.076 ± 0.29 cm) and descending colon wall thickness (DSCTHICK = 1.175 ± 0.366 cm) compared to controls (ASCTHICK = 0.6015 ± 0.1607 cm, DSCTHICK = 0.6223 ± 0.135 cm), p < 0.05. Men over 50 years had greater DSCTHICK (1.25 ± 0.434 cm) than post-menopausal women (0.986 ± 0.389 cm), p < 0.05. DSCTHICK significantly predicted diastolic blood pressure (β = -0.295, p < .05) and blood sodium level (β = -0.300, p < .05). Conclusion: We demonstrated the effects of IPIs on the intestinal microbiome causing intestinal wall cytoskeletal dysfunction, which led to the development of a "leaky gut syndrome."

Background/Objectives: This study looks at how a kinematic chain exercise regimen that targets the lower, core, and upper body affects university shot put participants' shoulder muscle strength and throwing efficiency. This study fills an apparent research void on shot put training approaches by presenting a comprehensive kinematic chain workout program. It was anticipated that this method would improve performance the most, considering the complex biomechanical require-ments of the sport. Methodology: Athletes, seventy in age (19.87 ± 1.31 years), were assigned into two groups at random: experimental (n = 35) and control (n = 35). While the control group carried on with their usual training, the experimental group participated in an 8-week kinematic chain training program, pre- and post-training evaluations were carried out to evaluate shot put throwing ability, shoulder muscle strength, and participant satisfaction with the exercise regimen. Results: demonstrated that, when compared to the control group, the athletes in the kinematic chain program had a significantly improved throwing distance (p = 0.01) and shoulder muscle strength (p = 0.01). Furthermore, there was a significant difference (p = 0.005) in the athletes' satisfaction levels with the workout program among those in the experimental group. This implies that a kinematic chain-focused strategy improves performance and emphasizes the significance this type of training is for shot put athlete performance. Conclusion: As an improvement forward in sports science, the study's finding promotes the inclusion of kinematic chain workouts in shot put training programs and calls for more research on kinematic chain-based approaches in a variety of sports.

Lean body mass (LBM) is correlated with powerlifting performance in athletes competing in different bodyweight classes. However, it remains unknown whether changes in LBM are correlated with performance changes in powerlifters preparing for a competition. Aim of the study was to investigate the changes in LBM and performance in powerlifters preparing for a competition. Eight male powerlifters (age 31.7±9.8years, height 1.77±0.06m, weight 99.2±14.6kg) and three female powerlifters (age 32.7±16.3years, height 1.54±0.06m, weight 66.6±20.9kg), participated in the study. Athletes followed individualized periodized training programs for 12 weeks aiming to maximize their performance for the national championship. Maximum strength (1-RM) in squat, bench press, and deadlift, body composition, grip strength, anaerobic power, quadriceps’ cross sectional area and vastus lateralis muscle architecture were measured before and after the training period. Significant increases were found after the training period in squat (5.8±7.0%, P