Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

In this study, the olive pomace was considered because of its importance in the environment. So, this study carried out to estimate the total nitrogen content and the fatty acids profile of olive pomace. The olive pomace samples were collected from Irbid, Jarash, Ajloun and Mafraq during the harvesting season 2014 to study the biochemical characteristics of fatty acid composition and the total nitrogen (TN) content. The total nitrogen content was determined by standard Kjeldahl method and the fatty acid profile was detected by gas chromatography (GC). The results show that the total nitrogen content ranged from (0.39 ± 0.0) to (0.62 ± 0.02) with statistically significant difference suggesting that the composition of matrices and their percentage may be responsible for composition of amendments. The calculated total protein percentage ranged between (2.43 ± 0.00) to (3.87 ± 0.17). Also, 13 different fatty acids were quantitatively profiled and quantitated. Oleic acid (C 18:1) was found to be the highest percentage of all other fatty acids and ranged between (59.03%) and (63.81%), moreover the C 18:1/C 18:2 (oil quality) was calculated and C.V% showed variation meaning that nutritional implication could affect the oxidative stability of oils. In conclusion, OP by-product could give a sustainable and alternative-cheap source for fertilizers, pharmaceutical industries, cosmetics and other industries.

Background: Condoms have proven to be an effective contraceptive barrier method of family planning and have played a vital role in preventing sexually transmitted diseases including HIV. However, existing evidence shows that utilization of condoms still remains low, especially among youth and adolescents. We aimed to determine the prevalence of condom use and associated factors among the students of Gulu university in Uganda. Methods: A cross-sectional study was conducted among undergraduate students of Gulu University between June and December 2023. The students were accessed from their respective faculties and chosen using a simple random sampling method. Data were collected using a pretested self-administered structured questionnaire. Condom use was defined as use of either male or female condom in the last sexual encounter in the previous six months. Results: A total of 404 participants, with a median age of 23 years (interquartile range (21.5-24) years) were enrolled in the study, 54.2%(n=219) of whom were male. Overall, 81.4%(n=329) of the participants were in senior classes (year 2,3,4, and 5) and 18.6%(n=75) were in their first year of study. The prevalence of condom use was 53.7%(n=217). Prevalence of condom use was 50.2%(n=109) among male and 49.8%(n=108) among female students. Year of study (senior class)(aPR = 1.4, 95% CI = 1.59, 3.54), having a sexual partner (aPR = 2.4, 95% CI = 1.89, 2.94), having a sexual partner within campus (aPR = 2.0, 95% CI = 1.69, 2.45), experience of condom bursting (aPR = 1.3, 95% CI = 1.08, 1.61), having sex in absence of condoms (aPR = 0.6, 95% CI = 0.44, 0.70), alcohol use (aPR = 1.2, 95% CI = 1.01, 1.45) were independently associated with condom use. Conclusion: Just over half of undergraduate students of Gulu university used condoms during sexual encounters. There should be heighten campaigns on condom use to prevent unintended pregnancies and sexually transmitted infections.

Accurate and consistent rainfall observations are vital for climatological studies in support of better planning and decision making. However, estimation of accurate spatial rainfall is limited by sparse rain gauge distributions. Satellite rainfall products can thus potentially play a role in spatial rainfall estimation but their skill and uncertainties need to be under-stood across spatial-time scales. This study aimed at assessing the temporal and spatial performance of seven satellite products (TARCAT (Tropical Applications of Meteorology using SATellite and ground-based observations (TAMSAT) African Rainfall Climatology And Time series), Climate Hazards Group InfraRed Precipitation with Station data (CHIRPS), Tropical Rainfall Measuring Mission (TRMM-3B43), Climate Prediction Center (CPC) Morphing (CMORPH), the Precipitation Estimation from Remotely Sensed Information using Artificial Neural Networks- Climate Data Record (PERSIANN-CDR), CPC Merged Analysis of Precipitation (CMAP) and Global Precipitation Climatology Project (GPCP) using gridded (0.05o) rainfall data over East Africa for 15 years(1998-2012). The products’ error distributions were qualitatively compared with large scale horizontal winds (850 mb) and elevation patterns with respect to corresponding rain gauge data for each month during the ‘long’ (March-May) and ‘short’ (October-December) rainfall seasons. For validation only rainfall means extracted from 284 rain gauge stations were used, from which qualitative analysis using continuous statistics of Root Mean Squared Difference, Standard deviations, Correlations, coefficient of determinations (from scatter plots) were used to evaluate the products’ performance. Results revealed rainfall variability dependence on wind flows and modulated by topographic influences. The products’ errors showed seasonality and dependent on rainfall intensity and topography. Single sensor and coarse resolution products showed lowest performance on high ground areas. All the products showed low skills in retrieving rainfall during ‘short’ rainfall season when orographic processes were dominant. CHIRPS, CMORPH and TRMM performed well, with TRMM showing the best performance in both seasons. There is need to reduce products’ errors before applications.

A thorough analysis and comparison of the fatty acid profiles of stipe and blade from Laminaria hyperborea, a kelp species found in the northern Atlantic, is presented. Lipids were extracted and fractionated into neutral lipids, free fatty acids and polar lipids, then derivatized to fatty acid methyl esters prior to GC-MS analysis. A total of 42 fatty acids were identified and quantified, including the n-3 fatty acids α-linolenic acid, stearidonic acid and eicosapentaenoic acid. An n-6/n-3 ratio of 0.8:1 was found in blade and 3.5:1 in stipe, respectively. The ratios vary between the lipid fractions within stipe and blade, with the lowest ratio in the polar lipid fraction of blade. The fatty acid amounts are higher in blade than in stipe, and the highest amounts of n-3 fatty acids are found within the neutral lipid fractions. The amounts of polyunsaturated fatty acids are 3.4 times higher in blade than stipe. This study highlights the compositional differences between the lipid fractions of stipe and blade from L. hyperborea. The amount of polyunsaturated fatty acids, compared to saturated- and monounsaturated fatty acids, as well as the n-6/n-3-ratio, is known to influence human health. In the pharmaceutical, food, and feed industries this can be of importance for production and sale of different health products. Additionally, lipids are today among the unused by products of alginate production, exploiting this material for commercial interest should give both economical and environmental benefits.

We propose a novel unsupervised semantic segmentation method for fast and accurate flood area detection utilizing color images acquired from Unmanned Aerial Vehicles (UAVs). To the best of our knowledge, this is the first fully unsupervised method for flood area segmentation in color images captured by UAVs, without the need of pre-disaster images. The proposed framework addresses the problem of flood segmentation based on parameter-free calculated masks and unsupervised image analysis techniques. First, a fully unsupervised algorithm gradually excludes areas classified as non-flood utilizing calculated masks over each component of the LAB colorspace, as well an RGB vegetation index and the detected edges of the original image. Unsupervised image analysis techniques, such as distance transform, are then applied, producing a probability map for the location of flooded areas. Finally, flood detection is obtained by applying the hysteresis thresholding segmentation. The proposed method is tested and compared with variations, and other supervised methods in two public datasets, consisting of 953 color images in total, yielding high-performance results, with 87.4% and 80.9% overall accuracy and F1-Score, respectively. The results and computational efficiency of the proposed method show that it is suitable for on board data execution and decision-making during UAVs flight.

The apicomplexan parasite, Sarcocystis neurona causes the degenerative neurological equine protozoal myeloencephalitis (EPM) disease of horses. Due to its host range expansion, S. neurona is an emerging threat that requires close monitoring. In apicomplexans, protein kinases (PKs) have been implicated in a myriad of critical functions such as host cell invasion, cell cycle progression and host immune responses evasion. Here, we used various bioinformatics methods to define the kinome of S. neurona and phylogenetic relatedness of its PKs to other apicomplexans. Further, three-dimensional (3D) homology models for selected S. neurona putative PKs were constructed and evaluated for inhibitor docking. We identified 92 putative PKs clustering within the AGC, CAMK, CK1, CMGC, STE, TKL, aPK and OPK groups. Although containing the universally conserved PKA (AGC group), S. neurona kinome was devoid of PKB and PKC, but contained the six apicomplexan conserved CDPKs (CAMK group). The OPK group was represented by ROPKs 19A, 27, 30, 33, 35 and 37, but was devoid of the virulence-associated ROPKs 5, 6, 18 and 38. Two out of the three S. neurona CK1 enzymes had high sequence similarities to T. gondii TgCK1-α and TgCK1-β and the Plasmodium PfCK1. Docking of four inhibitors onto homology models of putative ROP27 and PKA indicated that inhibition of S. neurona PKs is feasible, but needs to be experimentally tested. The essentiality of apicomplexan PKs makes the elucidation of S. neurona kinome a key milestone for development of novel therapeutics for EPM.

Abstract: Rice is one of the most important food crops in sub-Saharan Africa. Climate change, variability, and economic globalization threaten to disrupt rice value chains across the subcontinent, undermining their important role in economic development, food security, and poverty reduction. This paper maps existing research on the vulnerability of rice value chains, synthesizes the evidence and the risks posed by climate change and economic globalization, and discusses agriculture and rural development policies and their relevance for the vulnerability of rice value chains in sub-Saharan Africa. Important avenues for future research are identified. These include the impacts of multiple, simultaneous pressures on rice value chains, the effects of climate change and variability on parts of the value chain other than production, and the forms and extent to which different development policies hinder or enhance the resilience of rice value chains in the face of climatic and other pressures.

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

The ethics of invertebrate research have largely been ignored compared to the consideration of higher order animals, but more recent focus has questioned this trend. Using biohybrid robotic jellyfish as a case study, we examine the ethical considerations of invertebrate work and provide recommendations for future guidelines. This paper starts with an overview of philosophical views of animal ethics, the current state of knowledge for invertebrate pain and nociception, and current ethical guidelines. Next, we delve into the case study and analogous precedents. Specifically, in prior studies, we developed biohybrid robotic jellyfish, which modified live moon jellyfish with microelectronic swim controllers for future applications in ocean monitoring. Although jellyfish possess no central nervous system, pain receptors, or nociceptors, we closely monitored their stress responses, using the precautionary and minimization principles in consideration of the 4Rs: reduction, replacement, refinement, and reproducibility. We also discuss ethical considerations related to our studies and suggest that public opinion of invertebrate research relies heavily on repugnance, including fears of ‘playing God’ or limiting the ‘free will’ of animals. These issues are also examined for prior bioethics cases, such as the RoboRoach, cyborg beetle, ‘microslavery’ of microbes, biohybrid robots incorporating tissues from sea slugs (which are known to possess nociceptors), and other tissue cutting experiments involving soft-bodied invertebrates. However, biohybrid robotic jellyfish pose further ethical questions of potential ecological consequences as ocean monitoring tools, such as the impact of electronic waste in the ocean. To conclude these evaluations, we recommend that publishers require brief ethical statements for invertebrate research, which can include the following: a scientific justification for the research, discussion of the 4Rs, and cost-benefit analysis. We also delineate the need for more research on pain and nociception in invertebrates, which can then be used to revise or validate current research standards. These actions provide a stronger basis for the ethical study of invertebrate species, with implications for individual, species-wide, and ecological impacts on animals, as well as for interdisciplinary studies in science, engineering, and philosophy.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

The present study aimed at investigating the in vitro and in vivo susceptibility of malaria parasites to crude extracts and fractions from Polyalthia suaveolens, Uvaria angolensis, and Monodora tenuifolia. The ethanolic extracts were prepared by maceration, and were further partitioned using water, dichloromethane, hexane, and methanol. The most promising fraction was subjected to column chromatography and the sub-fractions tested for activity in vitro. The antiplasmodial effect of extracts and fractions was tested against the Chloroquine resistant (PfK1) strain in 96 wells microtiter plate format using SYBR green florescence assay. The promising fraction was further assessed for cytotoxicity and acute toxicity in Swiss albino mice and subsequently against the rodent malaria parasite, P. berghei. Qualitative phytochemical screening was also performed on the promising fraction. The methanol fractions exerted the overall better effect with that of the twigs of P. suaveolens (PStw(Ace)) showing the highest potency with a IC50 value of 3.24 µg/mL followed by the fractions of leaf of M. tenuifolia (MoTel(Ace), IC50= 3.84 µg/ml) and stem bark of P. suaveolens (IC50= 4.90 µg/ml). The phytochemical screening showed the presence of alkaloids, lactones, and phenols in the more active fraction of P. suaveolens (PStw(Ace)). The chromatographic fractionation of this fraction led to 12 sub-fractions with PS8 sub-fraction being the most active (IC50= 4.42 µg/mL). In vivo, oral administration of 2000 mg/kg b.w of fraction PStw(Ace) in mice showed no signs of toxicity. Also, fraction PStw(Ace) at 400 mg/kg b.w exerted the highest suppressive effect against P. berghei strain B throughout the 4 days experiment (% parasitaemia below 5.2%). Overall, the results achieved supported the use of the three plants in the traditional treatment of malaria in Cameroon. More interestingly, the methanolic fraction of the twigs extract from P. suaveolens might be of interest in future development of an antimalarial phytodrug.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

Motivated by a common Mathematical Finance topic, this paper surveys several results concerning windings of 2-dimensional processes, including planar Brownian motion, complex-valued Ornstein-Uhlenbeck processes and planar stable processes. In particular, we present Spitzer's asymptotic Theorem for each case. We also relate this study to the pricing of Asian options.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

The introduction of organic and inorganic substances to the environment is a result of human activities such as agriculture, domestic and industrial wastewater which leads to pollution. Treatment processes of these wastewaters are being conducted globally to eliminate easily settled materials and recover nutrients in an attempt to release clear and apparently clean effluent into natural waters. Lack of removing inorganic nitrogen and phosphorus nutrients is the greatest cause of eutrophication in water bodies which inhibits the life of other organisms as well as pose a threat to human life and loss of the economy. Different technologies have been applied and are being developed to recover nutrients as well as heavy metals from wastewater to meet the permissible limits before discharging effluents. Wastewater treatment using microalgae offers an opportunity to provide tertiary bio-treatment and production of valuable biomass. Microalgae use the available inorganic nitrogen and phosphorus for their growth which are then harvested for various uses. Additionally, they have the ability to remove heavy metals and some toxic compounds. The main specific microalgae species in this study is the Chlorella sorokiniana with the Aequorea victoria jellyfish This paper reviews some of the wastewater treatment processes and focus on the use of microalgae and some of the shortcomings of the technologies and how they can be improved to achieve maximum nutrient recovery economically with low energy demand.

Shigella and Salmonella have been implicated in neonatal sepsis, food poisoning, and bacteremia. Their increasing resistance to antibiotics has undermined treatment options, constituting a public health crisis. Also, the scarcity of new antibiotics in the development pipeline compounds multidrug-resistance (MDR). Hence, there is a need to potentiate antibiotics to mitigate resistance. This study leveraged riboflavin to re-sensitize fluoroquinolones and carbapenems against MDR Shigella and Salmonella spp. Disk diffusion, microbroth-dilution, chequerboard, and time-kill assays were used to determine resistance profiles and riboflavin-antibiotic activity. Biofilm-formation and bacterial viability (after riboflavin-antibiotic challenge) was determined with crystal-violet and Macrophage infection assays, respectively. Strains exhibited >80% resistance to fluoroquinolones and carbapenems, with 160–320 µg MIC ranges and 0.5–2 FIC, indicating no synergy. At 40–80 µg riboflavin, there was two-fold reduction in bacterial survival, with meropenem-riboflavin exhibiting significant reduction and FIC of 0.075 indicating high synergistic activity. Biofilm-formation was altered (from strong to weak phenotype) with 40 µg riboflavin-antibiotic treatment. There was a 40–70% reduction in bacterial survival in THP-1 cells treated with meropenem-riboflavin after 3 hours, and complete clearance between 24-48 hpi. Riboflavin potentiated fluoroquinolones and meropenem, leading to modulation of the host immune response for the clearance of the strains.

This treatise offers a philosophical odyssey into the exigency of conservation within the broader context of an increasingly interconnected world, beset by the perils of globalization, climate change, and the looming specter of global warming. Employing the evocative metaphor of a jellyfish, it endeavors to shed light on the paramount role of humanity as the principal protagonist in the saga of environmental predicaments, thereby accentuating our profound moral responsibility to navigate the labyrinthine pathways toward viable solutions. While this discourse abstains from presenting empirical or case-specific inquiries, it unfurls an incisive analytical vantage point that enriches our cognitive grasp of the intricate interplay between human societies and the pristine realms of the natural order. By expounding upon poignant exemplars of environmental degradation and unveiling the resplendent tapestry of statistical observations, the profound ethical imperatives that undergird the imperative to confront predicaments such as climate change are thrust into the limelight of intellectual inquiry. Consequently, by delving deep into these philosophical bedrocks, this magnum opus augments our erudition concerning the multifaceted nexus that binds humankind to their surroundings, thus affording us a glimpse into the subtle tapestry of a complex relationship that must be diligently nurtured and preserved.

Elevated carbon dioxide (eCO₂) stimulates wheat grain yield, but simultaneously reduces protein (N) concentration. Also other essential nutrients are subject to change. This study is a comprehensive synthesis of wheat experiments with eCO₂, estimating effects on N, minerals (B, Ca, Cd, Fe, K, Mg, Mn, Na, P, S, Zn), and starch. Analysis was made by i) deriving response functions for the relative effect on element concentration in relation to CO₂ concentration, ii) meta-analysis to test the magnitude and significance of observed effects, and iii) relating CO₂ effects on minerals to effects on N and grain yield. Responses range from zero to strong negative effects of eCO₂ on mineral concentration, with largest reductions for the nutritionally important elements N, Fe, S, Zn and Mg. Together with the positive but small and non-significant effect on starch concentration, the large variation in effects suggests that CO₂-induced responses cannot be explained by a simple dilution model. To explain the observed pattern, uptake and transport mechanisms may have to be considered, along with the link of different elements to N uptake. Our study shows that eCO₂ has a significant effect on wheat grain stoichiometry, with implications for human nutrition in a world of rising CO₂.

Despite the successful introduction of oral cholera vaccines, Zambia continues to experience multiple, sporadic, and protracted cholera outbreaks in various parts of the country. While vaccines have been useful in staying the cholera outbreaks, the ideal window for re-vaccinating individual’s resident in cholera hotspot areas remains unclear. Using a prospective cohort study design, 225 individuals were enrolled, re-vaccinated with two doses of Shanchol™ regardless of previous vaccination and followed-up for 90 days. Bloods collected at baseline before re-vaccination, at day 14 prior to second dosing and subsequently on days 28, 60, and 90. Vibriocidal assay was performed on samples collected at all five time points. Our results showed that anti-LPS and vibriocidal antibody titers increased at day 14 after re-vaccination and decreased gradually at 28, 60 and 90 across all the groups. Seroconversion rates were generally comparable in all treatment arms. We therefore conclude that vibriocidal antibody titers generated in response to re-vaccination still wane quickly irrespective of previous vaccination status. However, despite the observed decline, the levels of vibriocidal antibodies remained elevated over baseline values across all groups, an important aspect for Zambia where there is no empirical evidence as to the ideal time for re-vaccination.

The aim of this paper is to investigate the amenability modulo an ideal of Banach algebras with emphasis on applications to homological algebras. In doing so, we show that amenability modulo an ideal of A^** implies amenability modulo an ideal of A. Finally, for a large class of semigroups, we prove that l¹(S)^** is amenable modulo Iσ^** if and only if an appropriate group homomorphic image of S is finite where Iσ is the closed ideal induced by the least group congruence σ.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

Among magnetoelectric (ME) heterostructures, ME laminates of the type Metglas-like / PVDF (magnetostrictive+piezoelectric constituents) have shown the highest induced ME voltages, usually detected at the magnetoelastic resonance of the magnetostrictive constituent. This ME coupling happens because of the high cross-correlation coupling between magnetostrictive and piezoelectric material, and is usually associated with a promising application scenario for sensors or actuators. In this work we detail the basis of the operation of such devices, as well as some arising questions (as size effects) concerning their best performance. Also, some examples of their use as very sensitive magnetic fields sensors or innovative energy harvesting devices will be presented At the end, the challenges, future perspectives and technical difficulties that will determine the success of ME composites for sensor applications are discussed.

Jellyfish search (JS) algorithm impersonates the foraging behavior of jellyfish in the ocean. It is a new developed meta-heuristic algorithm that solves complex and real world optimization problems. The global explore capability and robustness of JS are strong, but JS still has great development space in solving complex optimization problems with high dimensions and multiple local optima. Therefore, an enhanced jellyfish search (EJS) algorithm is developed in this study, and three improvements are made: (i) By adding sine and cosine learning factors, the jellyfish can learn from both random individual and best individual during Type B motion in swarm to enhance the optimization capability and convergence speed; (ii) Adding local escape operator can skip local optimal trap and boost the exploitation ability of JS; (iii) Opposition-based learning operator and quasi-opposition learning operator can increase and strengthen the population distribution more diversified, and better individuals are selected from present and new opposition-solution to participates in the next iteration, which can boost the solution’s quality, meanwhile convergence speed is fasted and its precision is increased. In addition, the performance contrast of the developed EJS and some previous outstanding and advanced methods are evaluated on CEC2017, CEC2019 test suite and six real engineering example of case. It is demonstrated that EJS algorithm escaped the trap of local optimum, enhanced the solution’s quality and the calculation speed. What’s more, the practical engineering applications of EJS algorithm also verify its superiority and effectiveness in solving both constrained and unconstrained optimization problems, and it stretched one’s mind for solving such optimization problems.

Remote sensing datasets are increasingly being used to provide spatially explicit large scale evapotranspiration (ET) estimates. The focus of this study was to estimate and thematically map on a pixel-by-pixel basis, the actual evapotranspiration (ET_a) of the Wonji Shoa Sugarcane Estate using the Surface Energy Balance Algorithm for Land (SEBAL), Simplified Surface Energy Balance (SSEB) and Operational Simplified Surface Energy Balance (SSEBop) algorithms. The results obtained revealed that the ranges of the daily ETa estimated on January 25, February 26, September 06 and October 08, 2002 using SEBAL were 0.0 - 6.85, 0.0 – 9.36, 0.0 – 3.61, 0.0 – 6.83 mm/day; using SSEB 0.0 - 6.78, 0.0 – 7.81, 0.0 – 3.65, 0.0 – 6.46 mm/day, and SSEBop were 0.05 - 8.25, 0.0 – 8.82, 0.2 – 4.0, 0.0 – 7.40 mm/day, respectively. The Root Mean Square Error (RMSE) values between SSEB and SEBAL, SSEBop and SEBAL, and SSEB and SSEBop were 0.548, 0.548, and 0.99 for January 25, 2002; 0.739, 0.753, and 0.994 for February 26, 2002;0.847, 0.846, and 0.999 for September 06, 2002; 0.573, 0.573, and 1.00 for October 08, 2002, respectively. The standard deviation of ET_a over the sugarcane estate showed high spatio-temporal variability perhaps due to soil moisture variability and surface cover. The three algorithm results showed that well watered sugarcane fields in the mid-season growing stage of the crop had higher ET_a values compared with the other dry agricultural fields confirming that they consumptively use more water. Generally during the dry season, ET_a is limited to water surplus areas only and in wet season, ET_a was high throughout the entire sugarcane estate. The evaporation fraction (ETrF) results also followed the same pattern as the daily ET_a over the sugarcane estate. The total crop and irrigation water requirement and effective rainfall estimated using the Cropwat model were 2468.8, 2061.6 and 423.8 mm/yr for January 2001 planted and 2281.9, 1851.0 and 437.8 mm/yr for March 2001 planted sugarcanes, respectively. The mean annual ET_a estimated for the whole estate were 107 Mm³, 140 Mm³, and 178 Mm³ using SEBAL, SSEB, and SSEBop, respectively. Even though the algorithms should be validated through field observation, they have potential to be used for effective estimation of ET in the sugarcane estate.

The Drinking Water Directive (EU) 2020/2184 includes the parameter microcystin-LR, a cyanotoxin, which drinking water producers need to analyze if the water source has potential for cyanobacterial blooms. In light of the increasing occurrences of cyanobacterial blooms worldwide and given that more than 50 percent of the drinking water in Sweden is produced from surface water, both fresh and brackish, the need for improved knowledge about cyanotoxin occurrence and cyanobacterial diversity has increased. In this study a total of 98 cyanobacterial blooms were sampled in 2016-2017 and identified regarding their toxin production and taxonomical compositions. The surface water samples from freshwater lakes throughout Sweden including brackish water from 8 east coast locations along the Baltic Sea were analyzed for their toxin content with LC-MS/MS and taxonomic composition with 16S rRNA amplicon sequencing. Both the extracellular and the total toxin content was analyzed. Microcystin´s prevalence was highest with presence in 82% of blooms, of which as free toxins in 39% of blooms. Saxitoxins were found in 36% of blooms in which the congener decarbamoylsaxitoxin (dcSTX) was detected for the first time in Swedish surface waters at four sampling sites. Anatoxins were most rarely detected, followed by cylindrospermopsin, which were found in 6% and 10% of samples, respectively. As expected, nodularin was detected in samples collected from the Baltic Sea only. The cyanobacterial operational taxonomic unit (OTU) with the highest abundance and prevalence could be annotated to Aphanizomenon NIES-81 and the second most profuse cyanobacterial taxon to Microcystis PCC-7914. In addition, two correlations were found, one between Aphanizomenon NIES-81 and saxitoxins and another between Microcystis PCC-7914 and microcystins. This study is of value to drinking water management and scientists involved in recognizing and controlling toxic cyanobacteria blooms.

The cassava whitefly, Bemisia tabaci, causes direct damage to cassava in the tropics by feeding on the phloem of leaves, inducing leaf chlorosis and abscission which can result in considerable yield loss of up to about 50% on susceptible varieties. The pest is also known to impart its indirect damage through sooty mold formation. Most of the improved cassava varieties in Uganda were developed for CMD resistance and CBSD tolerance and little is known about their reaction to whitefly infestation. A study was conducted to evaluate the reaction of 24 improved cassava varieties which were sourced from 5 different countries in the region (Uganda, Kenya, Tanzania, Malawi, and Mozambique) to whitefly infestation. These varieties were evaluated in three agro-ecological zones of Uganda, namely; North-Western Savannah Grassland, Lake Victoria Crescent and the Kyoga Plains in the second rains of 2016. Monthly data were taken on adult and nymph counts, whitefly and sooty mold damage, CMD and CBSD severities from 2 up-to 9 Months after planting (MAP). Results show that the whitefly population was highly significantly (P

This paper analyzes the causal effect between domestic private investment, public investment, foreign direct investment and economic growth in Tanzania during the 1970-2014 period. The modified neo-classical growth model is used to estimate the ieffect of investment on economic growth. Also, the economic growth models based on Phetsavong and Ichihashi (2012) [1], and Le and Suruga (2005) [2]are used to estimate the crowding out effect of public investment on domestic private investment on one hand and foreign direct investment on the other hand. In the same way, the crowding out effect of foreign direct investment on domestic private investment is estimated. A correlation test is applied to check the correlation among independent variables, and the results show that there is very low correlation suggesting that multicollinearity is not a serious problem. Moreover, the diagnostic tests including RESET regression errors specification test, Breusch-Godfrey serial correlation LM test, Jacque-Bera-normality test and white heteroskedasticity test reveal that the model has no signs of misspecification and that, the residuals are serially uncorrelated, normally distributed and homoskedastic. Broadly, the empirical results show that the domestic private investment and foreign direct investment play an important role in economic growth in Tanzania. Besides, a revealed negative, albeit weak, association between public and private investment suggests that the positive effect of domestic private investment on economic growth becomes smaller when public investment-to-GDP ratio exceeds 8-10 percent. Similarly, foreign direct investment tends to marginally reduce the impact of domestic private investment on growth. These results suggest that public investment and foreign direct investment need to be considered carefully in order to avoid a reduced positive impact of domestic private investment on growth. Domestic saving may be promoted to encourage domestic investment for economic growth.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

Science is addressing global societal challenges and, due to limitations in research financing, scientists are turning to public at large to jointly tackle specific environmental issues. Citizens are therefore increasingly involved in monitoring programs, appointed as citizen scientists with potential to delivering key data at near no cost to address environmental challenges, so fostering scientific knowledge and advise policy- and decision-makers. One of the first and most successful example of marine citizen science in the Mediterranean is represented by the integrative and collaborative implementation of several jellyfish spotting campaigns in Italy, Spain, Malta, Tunisia started in 2009. Altogether, in terms of time coverage, geographic extent, and number of citizen records, these represent the most effective marine citizen science campaign so far implemented in the Mediterranean Sea. Here we analyzed a collective database merging records over the above four Countries, featuring more than 100,000 records containing almost 25,000 observations of jellyfish specimens, collected over a period of 3 to 7 years (from 2009 to 2015) by citizen scientists participating in any of the national citizen science programs included in this analysis. Such a wide citizen science exercise demonstrates to be one of the so far available most valuable and cost-effective tools to understanding ecological drivers of jellyfish proliferations over the Western and Central Mediterranean basins, and a powerful contribute to develop tailored adaptation and management strategies, mitigate jellyfish impacts on human activities in coastal zones, and support implementation of marine spatial planning, Blue Growth and conservation strategies.

Extraction techniques of important bioactive molecules from the major concern of Seafood byproducts are getting emphasis for better valorization. Employing green extraction technologies for efficient and quality production of these bioactive molecules is also strictly required. Hence, understanding the extraction process parameters to effectively design an applicable optimization strategy could make this real. In this review, statistical optimization strategies applied for the extraction process parameters of bioactive molecules from Seafood byproducts are focused. The type of experimental designs, and techniques applied to criticize and validate the effects of independent variables on the extraction output was addressed. Dominant parameters studied were enzyme/substrate ratio, pH, time, temperature and power of extraction instruments. The yield of bioactive compounds, chitin and chitosan, proteins and peptides, enzymes and carotenoids (Astaxanthins) were the most studied responses. Efficiency and/or economic and quality considerations and their selected optimization strategies that favour the production of potential bioactive molecules were also reviewed.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

Relationships between the Farey sequence and the Riemann hypothesis other than the Franel-Landau theorem are discussed. Whether a function similar to Chebyshev’s second function is square-root close to a line having a slope different from 1 is discussed. The nontrivial zeros of the Riemann zeta function can be used to approximate many functions in analytic number theory. For example, it could be said that the nontrival zeta function zeros and the Möbius function generate in essence the same function - the Mertens function. A different approach is to start with a sequence that is analogous to the nontrivial zeros of the zeta function and follow the same procedure with both this sequence and the nontrivial zeros of the zeta function to generate in essence the same function. A procedure for generating such a function is given.

Recent findings support an association between childhood maltreatment and the presence of elevated psychopathic traits in adulthood. Using a community sample recruited online (N = 210), we sought to (1) confirm the relationship between childhood traumas and psychopathic traits, and (2) investigate the role of parenting styles in psychopathic traits. Consistent with our predictions, we found an association between all types of childhood traumas and disinhibition. Age and gender moderated the relations between psychopathic traits and childhood maltreatments. Parental rejection and overprotection were positively correlated with the presence of psychopathic traits, while parental emotional warmth was negative correlated. Although our results converge with previous findings, the strength of the correlations observed was not as compelling as in research on undergraduate students. We discuss the numerous interpretations for our findings, and highlight the limitations of research in the field of psychopathy and childhood trauma in the general population.

Oncolytic virotherapy is a promising immunotherapy approach for cancer treatment, utilizing viruses to preferentially infect and eliminate cancer cells while stimulating immune responses. In this review we synthesize current literature on the molecular circuits of immune sensing and response to oncolytic virotherapy; focusing on viral DNA or RNA sensing by infected cells, cytokine and danger-associated signal sensing by neighboring cells, and subsequent downstream activation of immune pathways. The sequential sense-and-response mechanisms involve the triggering of molecular sensors by viruses or infected cells to activate transcription factors and related genes for a breadth of immune responses. We describe how molecular signals induced in the tumor upon virotherapy can trigger diverse immune signaling pathways, activating both antigen-presenting cell-based innate and T cell-based adaptive immune responses. Insights into these complex mechanisms provide valuable knowledge for enhancing oncolytic virotherapy strategies.

Achieving high economic growth rate while maintaining low inflation rate, has become the main objective of monetary authorities all over the world. Indeed, empirical literature reflects that high inflation rates are detrimental to long run growth and entail welfare costs. To achieve this objective, central banks have availed different options from time to time which include inflation targeting. Monetary authorities in Tanzania have been targeting an inflation level of around 5 percent per annum for economic policy purposes. However, when high inflation is to be controlled, tight monetary policy is put in place which might in turn affect the economic activity. Also, the Tobin effect suggests that inflation causes individuals to substitute out of money and into interest earning assets, which leads to greater capital intensity which in turn promotes economic growth. Against these major points, this paper examines a non linear relationship between inflation and economic growth using both a quadratic and threshold endogenous models and attempts to identify the existence of threshold effects between these variables. The paper uses a data set spanning from 1967 to 2015. The most interesting finding of the estimations is that the estimated coefficient of the linear term of inflation is negative while the estimated coefficient of the square term of inflation is positive, suggesting a U-shaped effect as opposed to inverse or inverted U-shaped relationship found in other countries by previous studies. These results suggest that the Tobin effect may be valid for high inflation, in which people strongly realize the importance of substituting money for interest-bearing assets. This leads to an increase in capital investment, and in turn, an increase in economic growth even with high inflation rate. However, this U-shaped relationship between inflation and economic growth suggests that, the economy is better off at extremely low inflation episodes. The optimal inflation rate that ranges between 3.25 percent and 3.75 percent is obtained by minimizing the residual sum of squares and/or maximizing adjusted R-squared. These findings have some policy implications for the policymakers and development partners. The paper is consistent with policy suggestions by international agencies. Efforts to minimize inflation to a very low level are likely to have a positive effect on economic growth.

In August 4 2011, United Nations Environmental Program (UNEP) submitted an unprecedented, scientific, groundbreaking Environmental Assessment Report (EAR) of Ogoniland, to the Nigerian government. This was the outcome of a 14–month intensive evaluation of the extent of pollution. It was intended that UNEP’s recommendations would be implemented to restore the devastated environment, on the one hand, and on the other, counteract the numerous environmental health issues that have for decades, plagued Ogoniland. However, five years post EAR, and, despite the seriousness of the situation, no significant resolution has occurred, both on the part of the government, and on the part of Shell Petroleum Development Company (SPDC) or Shell. To date, millions of Niger Delta residents, particularly those living in the oil-bearing communities, continue to suffer severe consequences. Although, the assessment was conducted in Ogoniland, other communities in the Niger Delta are also affected. This article explores prevailing issues, using Ogoniland (a microcosm of the Niger Delta) as an example. A multidisciplinary approach for sustainable mitigation of environmental health risks in the Niger Delta is paramount, and Environmental Management tools offer valuable strategies. Adopting UNEP’s recommendations for addressing environmental health problems requires implementing the Environmental Management/Environmental Management System (EM/EMS) model.

Despite identical genetic constitution, a cancer cell population can exhibit phenotypic variations termed as non-genetic/non-mutational heterogeneity. Such heterogeneity – a ubiquitous nature of biological systems – has been implicated in metastasis, therapy resistance and tumour relapse. Here, we review the evidence for existence, sources and implications of non-genetic heterogeneity in multiple cancer types. Stochasticity/ noise in transcription, protein conformation and/or external microenvironment can underlie such heterogeneity. Moreover, the existence of multiple possible cell states (phenotypes) as a consequence of the emergent dynamics of gene regulatory networks may enable reversible cell-state transitions (phenotypic plasticity) that can facilitate adaptive drug resistance and higher metastatic fitness. Finally, we highlight how computational and mathematical models can drive a better understanding of non-genetic heterogeneity and how a systems-level approach integrating mathematical modelling and in vitro/in vivo experiments can map the diverse phenotypic repertoire, and identify therapeutic vulnerabilities of an otherwise clonal cell population.

Given the opportunities offered by foreign investment in energy infrastructure mostly by Chinese firms, the Government of Cambodia is giving high priority to developing hydropower resources for reducing energy poverty and powering economic growth. Using a “Political ecology of the Asian drivers” framework, this paper assesses China’s involvement in the development of large dams’ in Cambodia and its impacts on the access of natural resources such as water and energy by dam builders, local communities and the government. This analysis is based on 61 interviews and 10 focus group discussions with affected communities, institutional actors, Chinese dam builders and financiers in relation to the first large Chinese dam built in Cambodia, the Kamchay dam. Based on the results of the analysis this paper makes recommendations on how to improve the planning, implementation and governance of large dams to ensure that the dams’ benefits are shared more equally.

VSM is a recently introduced method for entering and displaying any type of knowledge, in a form that is both semantically precise for computation and intuitive for human understanding. VSM is the combination of a new semantic model, and the design for a dedicated user interface to support it. Here we present the implementation of this user interface, as a sophisticated HTML-element, <vsm-box>, that can be embedded in any web-based curation app. We show how developers can use it for biocuration projects, customize it to particular end-user needs, and contribute to its growth. Vsm-box is open-source at https://github.com/vsmjs/vsm-box under the AGPL license, as a JavaScript (ES6) Vue.js web-component that runs in all modern web browsers. It is the capstone of the Vsmjs organization at https://github.com/vsmjs that groups its supporting modules. Extensive supplementary material on VSM and vsm-box is available at https://vsmjs.github.io.

Abstract: Hyperuricemia is commonly diagnosed in subjects with abnormal purine metabolism. Prolonged hyperuricemia often associated with gout, which is a vital risk factor for joint dysfunction. The current study was designed to determine the efficacy of vitamin C supplements for treatment of high serum uric acid (UA) among hyperuricemic and gouty patients, and finding-out the effect of supplementation on serum creatinine (Cr) level and glomerular filtration rate (GFR). This intervention study was started in April, 2013, till two months. A convenient sample of 30 adults aged between 24-75 years of both genders was assigned into two study groups: hyperuricemic (n=15) and gouty (n=15) groups. Each participant supplemented with 500 mg/day vitamin C chewable tablets for 2 months. Serum UA, Cr, and GFR were measured before and after treatment. At the end of this study, Cr and GFR enhanced insignificantly in both groups. UA increased insignificantly in gouty group after 2 months by about 0.31 mg/dl. On the other hand, hyperuricemic group showed significant (P ≤0.05) decrease in UA (-0.78 mg/dl) after 2 months duration. In conclusion, supplementation with 500 mg/day vitamin C for 2 months significantly attenuated serum UA for hyperuricemic patients and insignificantly affected serum UA in gouty patients. The uselessness of vitamin C supplements on gouty patients could be associated to a number of possible reasons.

With the increasingly online exposure of urban public spaces, the new concept of "Internet-celebrity cities" has emerged in China. The online internet-famous sites are the main characteristics of "Internet-celebrity cities". To fully understand online users' preferences in such kind of public spaces, this article took 27 typical riverfront internet-famous sites (RIFS) in Changsha city (China), as an example. Through the online images and review comments on social media platform "Xiaohongshu", the study analyzed users’ perception of RIFS specially on visual and emotional preferences. It revealed the following findings:(1) The popularity of RIFS had a significant head effect and there were far more positive emotions than neutral and negative emotions in review comments. (2) According to 5 different categories of RIFS: modern buildings with river views, restaurants with strong visual impact became the main attractions on commercial RIFS. The art exhibition RIFS attracted visitors to experience traditional culture and highlight their aesthetic pursuits. In the historical and cultural RIFS, people preferred to see the historical buildings with surrounding natural environment, as well as river and mountains views. Ecological Recreational RIFS showed the similar results with the uncultivated RIFS, for the main focus was on the ecological environment, a broader vision and the specific atmosphere. Moreover, the uncultivated RIFS showed more diversified attraction points. This study can provide a new perspective on the waterfront vitality and can offer a targeted and attractive manner for waterfront regeneration that are different from traditional methods.

Directed energy deposition (DED) parameters were determined for near-β alloy Ti-55511 by employing statistical design of experiments (DOE) methods. Parameters resulting in fully dense freeform deposits were identified using two sequential DOEs. Single laser tracks were printed with several laser power, traverse rate, and powder feed rate settings in an initial DOE to identify promising build parameters. Capture efficiency and effective deposition rate were used to characterize and rank the single track deposits. The best parameters were then used to print solid cube with various X-Y and Z-overlaps (different hatch spacing, HS, and layer thickness, ZS) in a second DOE. Suitable deposition parameters were selected based on cube density and microstructure and were used to fabricate larger tensile samples for mechanical testing. Multiple parameter sets were found to provide dense Ti-55511 deposits with acceptable mechanical properties and parametric models showed statistical significance.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar (Sound Navigation And Raging) systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviours of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

Majority of the studied MADS box members are linked with flowering and fruit traits. However, higher volumes of studies on the type II of their two types so far suggest that florigenic effect of the gene members could just be tip of the iceberg. In current study we used a systematic approach to have general overview on the MADS box members their cross-trait and multifactor associations as well as their pleiotropic potentials based on local reference database curated for MADS box members. While doing so, we screened for the co-occurrence of the terms of interest within the title or abstract of each reference with threshold of 3 hits. Analysis results showed that our approach can retrieve multi-faceted information on the subject of study (MADS box gene members in current case) which could otherwise have been skewed depending on the authors’ expertise and/or volume of literature reference base. Overall, our study discusses on the roles of MADS box members in association with plant organs and traits-linked factors among plant species. Our assessment showed that plants with majority of the MADS box member studies include tomato, apple, rice etc., after Arabidopsis. Furthermore, based on the degree of their multi-trait associations, FLC, SVP, SOC1, etc. are suggested to have relatively higher pleiotropic potential among others in plant growth, development and flowering process. The approach devised in this study is expected applicable for having basic understanding on any study subject of interest regardless of depth prior knowledge.

We have identified a new human voltage-gated potassium channel (hKv1.3) blocker, NnK-1, in the jellyfish Nemopilema nomurai, based on its genomic information. The gene sequence encoding NnK-1 contains 5,408 base pairs, with five introns and six exons. The coding sequence of the NnK-1 precursor is 894 nucleotides long and encodes 297 amino acids, containing five presumptive ShK-like peptides. An electrophysiological assay demonstrated that the chemically synthesized fifth peptide, NnK-1, is an effective hKv1.3 blocker. A multiple sequence alignment with cnidarian Shk-like peptides, which have Kv1.3-blocking activity, revealed that four residues (3Asp, 25Lys, 33Lys, and 34Thr) of NnK-1, together with six cysteine residues, are conserved. Therefore, we hypothesize that these four residues are crucial for the binding of the toxins to voltage-gated potassium channels.

This document describes the theoretical basis of the algorithms used to determine properties of snow and ice from the measurements of the Ocean and Land Color Instrument (OLCI) onboard Sentinel-3 satellites within the Pre-operational Sentinel-3 snow and ice products (SICE) project: http://snow.geus.dk/. The code used for the SICE retrieval and its documentation can be found at https://github.com/GEUS-SICE/pySICE. The algorithms were developed after the work from Kokhanovsky et al. (2018, 2019, 2020).

Wetland ecosystems in the Qinghai-Tibet Plateau are pivotal for global ecology and regional sustainability, contributing significantly to terrestrial ecosystems by regulating runoff, mitigating floods, and enhancing water quality. This study investigates the dynamic changes in wetland ecosystems within the Chaidamu Basin and their response to drought, aiming to foster sustainable wetland utilization in the Qinghai-Tibet Plateau. Using Landsat TM/ETM/OLI data on the Google Earth Engine platform, we employed a random forest method for annual long-term land cover classification. Meteorological drought conditions were assessed using SPEI3, SPEI6, SPEI9, and SPEI12, derived from monthly precipitation and evapotranspiration data. Pearson correlation analysis examined the relationship between wetland changes and various SPEI scales. The BFASAT method evaluated the impact of SPEI12 trends on wetlands, while cross-wavelet analysis explored teleconnections between SPEI12 and atmospheric circulation factors. Our findings revealed that the land cover dataset of the Chaidamu Basin (1990-2020) exhibited diverse categories with high classification accuracy (OA: 90.27%, Kappa: 88.34%). Wetlands, including lake, glacier, and marsh types, exhibited a noticeable increasing trend. Wetland expansion occurred during specific periods (1990-1997, 1998-2007, 2008-2020), featuring extensive conversions between wetland and other types, notably from other types to wetlands. Spatially, lake and marsh wetlands predominated in the low-latitude basin, while glacier wetlands were situated at higher altitudes. The study identified significant negative correlations between SPEI at various scales and total wetland area and types, with SPEI12 exhibiting the most substantial effect between September and December (r <-0.75) on wetlands. SPEI12 displayed a decreasing trend with non-stationarity and distinct breakpoints in 1996, 2002, and 2011, indicating heightened drought severity. Atmospheric circulation indices (ENSO, NAO, PDO, AO, WP) exhibited varying resonance with SPEI12, with NAO, PDO, AO, and WP demonstrating longer resonance times and pronounced responses.The continuous growth of wetlands amidst increasing aridification emphasizes the need for thoughtful wetland development to establish a sustainable "forest-lake-grass-field-river" ecological community. These findings underscore the significance of comprehending wetland changes and drought dynamics for effective ecological management in the Chaidamu Basin of the Qinghai-Tibet Plateau.

A simple, isocratic and robust RP-HPLC method for the analysis of azithromycin was developed, validated and applied for the analysis of bulk samples, tablets and suspensions. The optimum chromatographic conditions for separation were established as mobile phase comprising of acetonitrile-0.1M KH₂PO₄ pH 6.5-0.1M tetrabutyl ammonium hydroxide pH 6.5-water (25:15:1:59% v/v/v/v) delivered at a flow rate of 1.0 ml/min. The stationary phase consisted of reverse-phase XTerra^® (250 mm× 4.6 mm i.d., 5 µm particle size) maintained at a temperature of 43 °C with a UV detection at 215 nm. The method was found to be linear in the range 50-150% (r²=0.997). The limits of detection and quantification were found to be 0.02% (20 µg) and 0.078% (78 µg) respectively with a 100.7% recovery of azithromycin. Degradation products of azithromycin in acidic and oxidative environments at 37 °C were resolved from the active pharmaceutical ingredient and thus the method is fit for the purpose of drug stability confirmation.

This study aimed at testing the effectiveness of novel combinations of chemical and physical methods to control Prosopis juliflora, an invasive weed in the Moshi and Simanjiro districts of Nothern Tan-zania. Six different treatments including manual uprooting, glyphosate, bark chop with chemical application, two separate chemical mixtures and control were tested in a total of 32 plots, which represented two land use types (grazing land and farmland) found in the two districts. Each plot covered 20m×30m plot area. Two response variables (stem count and tree volume) were recorded to compare weed population density before and after treatment six months later. An analysis of the untreated control plots, showed that the inherent growth potential of P. juliflora was higher in Moshi than in Simanjiro district. The number of stems increased during the experiment for all six treatments showing that the P. juliflora population had not yet reached the local carrying capacity. For the manual control treatment, the increase was reduced compared to the untreated control. For all other treatments, the increase in stem count was on par with that in the untreated control or even higher. Thus, we conclude that only manual uprooting had a controlling effect but not to the extent that it eradicated P. juliflora. Thus, it is for P. juliflora as for weed control in general: weed control must be an ongoing effort.

Hydrologic studies on rainfall-runoff have been extensively conducted in many regions around the globe to fulfill various desirable needs with a purpose of effective and proper planning and managing water resources for present and future uses, whereas such study is not well drawn much attention to river catchments of Tonle Sap Lake Basin in Cambodia, which may prevail to water insecurity. The Stung Sreng catchment, which is one among them considered to be a significant basin for water resources management in Cambodia, is remarkably increasing under intolerable pressures in water resources development. This study was to apply HEC-HMS (Hydrological Engineering Center-Hydrological Model System) model to predict streamflow of Stung Sangker catchment, located in Tonlesap Lake Basin in Cambodia. The result showed that the calibration was good at monthly basis. The model performance was given by Nash-Sutcliffe Efficiency criteria followed by 0.44 for daily and 0.71 for monthly basis, respectively. Moreover, the Percent Bias (PBIAS) for daily and monthly simulation was 4.13% and 3.56%, indicating a satisfactory model fit. The HEC-HMS conceptual model can be used to simulate flow of Stung Sangke catchment on a continuous time scale particularly monthly basis. The result also indicated that there was a clear seasonal variation in monthly water availability, especially during both wet and dry season.

Italian, Spanish, French vs German, Austrian or Norwegian COVID-19 tracks? Antibiotics might have a partial impact on COVID-19 death rates in various countries. Our working hypotheses based on recent publications is that that antibiotics may be a major factor that negatively affects patients’ immune system during viral infections. We are all aware that there is no specific and effective medical treatment for COVID-19 so far. However, we know that our immune system is the only efficient weapon that fights against this syndrome right now. In fact, antibiotics are very often prescribed to prevent secondary infections following an antiviral immune response. Various antibiotic therapies have also been commonly applied to support COVID-19 treatments in China and Italy. Unfortunately, the frequent antibiotic off-site targets include mitochondria that are genetically and evolutionary closely linked to bacteria. Mitochondria are multifunctional organelles responsible for bioenergetics in nearly all our cells, acting as signaling hubs in antiviral and antibacterial immune responses. Several studies have demonstrated that mitochondria are vulnerable to antibacterial treatments, interrupting their physiology. Inhibition of these processes by antibiotics might render the immune system less capable of fighting acute COVID-19 viral infections. Some antibiotics, including those prescribed for COVID-19 in Wuhan, have been shown to inhibit the synthesis of mitochondrial DNA. The question is whether antibiotics support such a treatment or weaken patient immune responses in this case. This hypothesis should be evaluated based on comparative clinical data that seem to be unavailable at the moment. Possibly the COVID-19 risk group should be extended to all patients being treated with antibiotics, including those who finished antibiotic therapies days up to several months before SARS-CoV-2 infection. We therefore urge health service response groups to evaluate the impact of antibiotics on COVID-19 recovery vs death retrospective data. We would like to motivate international, national and local health authorities to share available clinical treatment data, discuss and optimize treatment strategies.

Machine learning (ML) has emerged as a critical tool for making sense of the growing amount of genetic and genomic data available because of its ability to find complex patterns in high dimensional and heterogeneous data. While the complexity of ML models is what makes them powerful, it also makes them difficult to interpret. Fortunately, recent efforts to develop approaches that make the inner workings of ML models understandable to humans have improved our ability to make novel biological insights using ML. Here we discuss the importance of interpretable ML, different strategies for interpreting ML models, and examples of how these strategies have been applied. Finally, we identify challenges and promising future directions for interpretable ML in genetics and genomics.

Culverts are often required under earth embankment to allow for the crossing of a watercourse, like streams, to prevent the road embankment from obstructing the natural waterway. The opening of the culvert is determined based on the waterway required to accommodate the design flood, whereas the thickness of the culvert section is designed based on the loads applied to the culvert. This paper studies some design parameters of box culverts, such as the thickness of the haunch, the coefficient of earth pressure, the thickness of box culvert, and depth of fill on the top slab, to show the effect of haunch on the stresses of the box culvert. The study investigated the variation in stresses and the cost comparison made for different width of the box culvert. The percentage reduction in the cost of culvert based on the presence of haunch is presented.

In this paper, a new millimeter wave 3D imaging radar is proposed. The user just needs to move the radar along a circular track, a high resolution 3D imaging can be generated. The proposed radar uses the movement of itself to synthesize a large aperture in both the azimuth and elevation directions. It can utilize inverse Radon transform to resolve 3D imaging. To improve the sensing result, compressed sensing approach is further investigated. The simulation and experimental result further illustrated the design. Because a single transceiver circuit is needed, a light, affordable and high resolution 3D mmWave imaging radar is illustrated in the paper.

Herein, we examined the effects of weather parameters and individual clinicodemographic risk factors on hemorrhagic stroke (HS) incidence, severity on admission, and disability at discharge in a harsh desert climate. In a retrospective design we studied patients admitted to a stroke unit in Arab Emirates in 2016-2019. With a distributed lag nonlinear model we explored immediate and delayed effects of weather on stroke incidence. Supervised machine learning was used to build models predictive of scores in NIHSS and mRS scales. We assessed model performance by calculating ROC AUC, F1 scores, specificity, and sensitivity. HS risk increased after a significant change in any weather parameter. The risk was reduced below baseline after 1-week adjustment to environmental changes. Climate input from the previous 3 days yielded reliable classification models. Humidex was a better predictor of severity than air temperature, whereas body mass index, age, and time of day at stroke onset were the strongest clinical predictors. Weather parameters before admission were stronger predictors of disease severity than individual clinical factors. We addressed limitations of previous studies by analyzing a full set of climate parameters: ambient temperature, relative humidity, humidex, atmospheric pressure, and wind speed. Predictive models may help to optimize patient management and develop preventative strategies.

The stock beta coefficient literature extensively discusses the proper methods for the estimation of beta as well as its use in asset valuation. However, there are relatively few references with respect to the appropriate time horizon that investors should utilize when evaluating the risk-return relationship of a stock. We examine the appropriate time horizon for beta estimation differentiating our results by sector according to the Industry Classification Benchmark. We employ data from the NYSE and we estimate varying lengths of beta employing data from 30 to 250 trading days. The constructed beta series is then examined for the presence of breaks using the endogenous structural break literature. Results show evidence against the use of betas that employ more than 90 trading days of data provisional to the sector under study.

Drug repurposing, rebranding an existing drug for a new therapeutic indication, is deemed a beneficial approach for a quick and cost-effective drug discovery process by skipping preclinical, Phase 1 trials and pharmacokinetic studies. Several psychotropic drugs including selective serotonin reuptake inhibitors (SSRIs) and tricyclic antide-pressants (TCAs) were studied for their potential application in different diseases es-pecially in cancer therapy. Fluoxetine (FLX) is one of the most prescribed psychotropic agents from SSRIs class for the treatment of several neuropsychiatric disorders with a favourable safety profile. FLX exhibited different oncolytic effects via mechanisms dis-tinct from its main serotonergic activity. Taking advantage of its ability to rapidly pen-etrate the blood-brain barrier, FLX could be particularly useful in brain tumors. This was proved by different in vitro and in vivo experiments using FLX as a monotherapy or combination with temozolomide (TMZ) or radiotherapy. In this review of literature, we summarize the potential pleiotropic oncolytic roles of FLX against different cancers highlighting the multifaceted activities of FLX and its ability to interrupt cancer prolif-eration via several molecular mechanisms and even surmount multidrug resistance (MDR). We elaborated on the successful synergistic combinations such as FXR/temozolomide and FXR/raloxifene for the treatment of glioblastoma and breast cancer, respectively. We showcased beneficial pharmaceutical trials to load FLX on car-riers to enhance its safety and efficacy on cancer cells. This is the first review article ex-tensively summarizing all previous FLX repurposing studies for the management of cancer.

The advent of deep learning (DL) has revolutionized medical imaging, offering unprecedented avenues for accurate disease classification and diagnosis. DL models have shown remarkable promise for classifying brain tumor from Magnetic Resonance Imaging (MRI) scans. However, despite their impressive performance, the opaque nature of DL models poses challenges in understanding their decision-making processes, particularly crucial in medical contexts where interpretability is essential. This paper explores the intersection of medical image analysis and DL interpretability, aiming to elucidate the decision-making rationale of DL models in brain tumor classification. Leveraging state-of-the-art DL frameworks with transfer learning, we conduct a comprehensive evaluation encompassing both classification accuracy and interpretability. Using state-of-the-art DL frameworks with transfer learning, we conduct a thorough evaluation covering both classification accuracy and interpretability. We employ adaptive path-based techniques to understand the underlying decision-making mechanisms of these models. Grad-CAM and Grad-CAM++ highlight critical image regions where the tumors are located.

In this paper, some convexity properties and some inequalities for the (p,k)-analogue of the Gamma function, Г_p,k(x) are given. In particular, a (p,k)-analogue of the celebrated Bohr-Mollerup theorem is given. Furthermore, a (p,k)-analogue of the Riemann zeta function, ζ_p,k(x) is introduced and some associated inequalities are derived. The established results provide the (p,k)-generalizations of some known results concerning the classical Gamma function.

Studies employing Arellano-Bond and Blundell-Bond GMM estimation for single linear dynamic panel data models are growing exponentially in number. However, for researchers it is hard to make a reasoned choice between many different possible implementations of these estimators and associated tests. By simulation the effects are examined of many options regarding: (i) reducing, extending or modifying the set of instruments; (ii) specifying the weighting matrix in relation to the type of heteroskedasticity; (iii) using (robustified) 1-step or (corrected) 2-step variance estimators; (iv) employing 1-step or 2-step residuals in Sargan-Hansen overall or incremental overidentification restrictions tests. This is all done for models in which some regressors may be either strictly exogenous, predetermined or endogenous. Surprisingly, particular asymptotically optimal and relatively robust weighting matrices are found to be superior in finite samples to ostensibly more appropriate versions. Most of the variants of tests for overidentification restrictions show serious deficiencies. A recently developed modification of GMM is found to have great potential when the cross-sectional heteroskedasticity is pronounced and the time-series dimension of the sample not too small. Finally all techniques are employed to actual data and lead to some profound insights.

This review deals with the adaptive mechanisms that plants can implement to cope with the challenge of salt stress. Plants tolerant to NaCl implement a series of adaptations to acclimate to salinity, including morphological, physiological and biochemical changes. These changes include increases in the root/canopy ratio and in the chlorophyll content in addition to changes in the leaf anatomy that ultimately lead to preventing leaf ion toxicity, thus maintaining the water status in order to limit water loss and protect the photosynthesis process. Furthermore, we deal with the effect of salt stress on photosynthesis and chlorophyll fluorescence and some of the mechanisms thought to protect the photosynthetic machinery, including the xanthophyll cycle, photorespiration pathway and water-water cycle. Finally, we also provide an updated discussion on salt-induced oxidative stress at the subcellular level and its effect on the antioxidant machinery in both salt-tolerant and salt-sensitive plants. The aim is to extend our understanding of how salinity may affect the physiological characteristics of plants.

This study aimed to compare the differences in durability and prestress loss between normal-weight concrete (NC) and lightweight aggregate concrete (LWC) prestressed box girders, which were constructed at the same time in the same area, so as to verify the superiority of using synthetic lightweight aggregate (LWA) made from reservoir sediments in prestressed bridges. For the NCs and LWCs used in prestressed box girders, the basic mechanical properties were tested on the one hand, and the durability properties were tested on the other hand. Then, through the prestress monitoring system, the prestress loss of the two groups of the prestressed box girders was tracked. The results of the durability test confirmed that LWC can inhibit the penetration of air, water, and chloride ions by strengthening the interfacial transition zone between the aggregate and the cement paste, thereby improving its durability. Moreover, the magnetic flux prestress loss of the NC prestressed box girder reached 8.1%. In contrast, the magnetic flux prestress losses on both sides of the LWC prestressed box girder were 4.6% and 4.9%, respectively. This verified that, under the same environmental conditions, the use of LWC produced less of a prestress loss than the use of NC.

The Algiers Stock Exchange (ASE) is the only stock exchange in Algeria. It’s one of the newest and smallest emerging stock exchanges in the world. The focus of this paper is to model and forecast monthly returns of the ASE index (DZAIRINDEX) using The Box- Jenkins methodology. The period of this study is from Jun 2010 to July 2019. According to Akaike’s Information Criterion (AIC) estimator, the Seasonal Autoregressive Integrated Moving Average SARIMA(2,0,0)(0,0,1) is chosen as the best model for forecasting the monthly DZAIRINDEX returns. Diagnostic tests confirm that the fitted model is adequate, where the residuals of this model are normally distributed with no autocorrelation and no heteroskedasticity. The forecast of the monthly DZAIRINDEX returns for one year ahead using this model shows a decreasing fluctuations trend. Based on different measures of forecast accuracy such as ME, MAE, RMSE, MASE, we show that the forecast accuracy of SARIMA(2,0,0)(0,0,1) is acceptable and this model performs much better than a naïve model. These results could be used by the financial communities in Algeria to deal with stock exchange risks and to improve their decisions.

Time evolution of the quantum correlation of the hybrid qubit-qutrit system in multilocal and global dephasing under the effect of a classical noises environment is presented. We considered the qutrit in z direction and the qubit x direction. In addition, our system presents two configurations: the different and the common environment and our discussion involves three types of noises: A Static Noise (SN), Random Telegraph Noise (RTN) and Ornstein- Uhlenbeck noise (OU). By using the density matrix approach to determine the evolution of the state of the system, the found that the static noise is fatal for the quantum entanglement, the quantum correlation and for RTN and OU noises the quantum entanglement, the quantum correlation decreases monotonically with a sufficiently long time. Therefore, we can say that, entanglement and the quantum correlation are more robust to the noise precisely those Random telegraph noise and Ornstein-Uhlenbeck noise.

Aims of the paper are the results of a research on a wooden box that holds an important historical document, which is a hand Bible handwritten in the thirteenth century. The tradition connect this Bible to the name of Marco Polo (Venice, 1254 - Venice, 1324), who would be the owner and that it would accompany him on his travels (1262 and 1271) in China. The Bible, of fine workmanship, written on thin parchment, and its container, along with a yellow silk cloth, is preserved in the ancient and prestigious Laurentian Library in Florence. The manuscript was in very poor condition and in the course of the study (2011) was being restored. Aims of survey were to determine the place and period of realization of the box, or rather if it be contemporary or later than the manuscript it contains and whether it was made in the East or in Europe.

A sustainable green one pot procedure for the synthesis of dihydropyrimidinones (DHPMs) derivatives by a three-component reaction of β-ketoester derivatives, aldehyde and urea or thiourea over the alkali-treated H-ZSM-5 zeolite under ball-milling has been developed. The product was isolated by simple washing of the crude reaction residue with ethyl acetate followed by evaporation of solvent. The hierachical zeolite catalyst (MFI27_6) showed high yield (86–96%) of dihydropyrimidinones (DHPMs), in very short time (10-30 min). The catalyst is recycled for subsequent reactions in four runs without appreciable loss of activity and high yields of products provide efficient protocol for Biginelli reactions.

The fitting and modeling of skewed, complex, symmetric, and asymmetric datasets is an exciting research topic in many fields of applied sciences, notably lifetime, medical, and financial sciences. The Heavy tailed Nadarajah Haghighi model is introduced by compounding the heavy tailed family and Nadarajah Haghighi distribution in this paper. The so obtained model has three parameters accounting for the scale and shape of the distribution. The proposed distribution's fundamental characteristics such as probability density, cumulative distribution, hazard rate, and survival functions are provided, and several key statistical properties are established, and several entropy information measures are proposed. The estimation of model parameter is performed via the ML procedure. Further, different simulation experiments are conducted to demonstrate the performance of proposed estimator’s using some measure, like the average estimate, the average bias, and associated mean square error. Finally, we are applied our proposed model to analyze three different real datasets. In our illustration, we are compared the practicality of the recommended model with several well-known competing models.

Alzheimer's disease (AD) remains a significant challenge in the field of neurodegenerative disor-ders, even nearly a century after its discovery, due to the elusive nature of its causes. The develop-ment of drugs that target multiple aspects of the disease has emerged as a promising strategy to address the complexities of AD and related conditions. The immune system's role, particularly in AD, has gained considerable interest, with nanobodies representing a new frontier in biomedical research. Advances in targeting antibodies against amyloid-β (Aβ) and using messenger RNA for genetic translation have revolutionized the production of antibodies and drug development, open-ing new possibilities for treatment. Despite these advancements, conventional treatments for AD, such as Cognex, Exelon, Razadyne, and Aricept, often have limited long-term effectiveness, under-scoring the need for innovative solutions. This necessity has led to the incorporating of advanced technologies like artificial intelligence and machine learning into the drug discovery process for neurodegenerative diseases. These technologies help identify therapeutic targets and optimize lead compounds, offering a more effective approach to addressing the challenges of AD and similar conditions.

Establishing an accurate mathematical model is the foundation of simulating the motion of marine vehicles and structures, and it is the basis of modeling-based control design. System identification from observed input-output data is a practical and powerful method. However, for modeling objects with different characteristics and known information, a single modeling framework can hardly meet the requirements of model establishment. Moreover, there are some challenges in system identification, such as parameter drift and overfitting. In this work, three robust methods are proposed for generating ocean hydrodynamic models based on Bayesian regression. Two Bayesian techniques, semi-conjugate linear regression and noisy input Gaussian process regression, are used for parametric and nonparametric gray-box modeling and black-box modeling. The experimental free-running tests of the KVLCC2 ship model and a multi-freedom wave energy converter (WEC) are used to validate the proposed Bayesian models. The results demonstrate that the proposed schemes for system identification of the ship and WEC have good generalization ability and robustness. Finally, the developed modeling methods are evaluated considering the aspects required conditions, operating characteristics and prediction accuracy.

This study examines how the design of museum archaeological boxes and the overall museum image affect behavioral intention. This research used partial least squares-structural equation modeling, indicating a relationship between aesthetics, symbolism, affective museum image, perceived value, and behavioral intention. This study found that symbolism predicted behavioral intention. Moreover, aesthetics, symbolism, and affective museum image affected perceived value, in turn triggering behavioral intention. This indicates theoretical and practical implications for museum products.

The creation of a Europe-wide electricity market combined with the increased intermittency of supply from renewable sources calls for an investigation into the risk of aggregate peak demand. This paper makes use of a risk model to assess differences in time-use data from residential end-users in five different European electricity markets. Drawing on the Multinational Time-Use Survey database, it assesses risk in relation to the probability of electrical appliance use within households for five European countries. Findings highlight in which countries and for which activities the risk of aggregate peak demand is higher and link smart home solutions (automated load control, dynamic pricing and smart appliances) to different levels of peak demand risk.

In a recent paper, Sarikaya et al. introduced a new analogue of the classical Gamma function which they called, the conformable Gamma function. Motivated by their results, this paper seeks to establish some inequalities for the conformable Gamma and Polygamma functions. Among other analytical tools, the procedure relies on the generalized forms of some classical inequalities.

The greater Wellington region, New Zealand, is highly vulnerable to large earthquakes because it is cut by active faults. Bulk water supply pipelines cross the Wellington Fault at several different locations, and there is considerable concern about severe disruption of the provision of reticulated water supplies to households and businesses in the aftermath of a large earthquake. A number of policy initiatives have been launched encouraging householders to install rainwater tanks to increase post-disaster resilience. However, little attention has been paid to potential health hazards associated with consumption of these supplies. To assess health hazards for householders in emergency situations, six 200-litre emergency water tanks were installed at properties across the Wellington region, with five tanks being allowed to fill with roof-collected rainwater and one tank being filled with municipal tapwater as a control. Such tanks are predominantly set aside for water storage, and once filled, feature limited drawdown and recharge. Sampling from these tanks was carried out fortnightly for one year, and samples analysed for E. coli, pH, conductivity, a range of major and trace elements, and organic compounds, enabling an assessment of the evolution of water chemistry in water storage tanks over time. Key findings were that the overall rate of E.coli detections in the rain-fed tanks was 17.7%, which is low in relation to other studies. We propose that low incidences of E.coli may be due to biocidal effects of high zinc concentrations in tanks, originating from unpainted galvanised steel roof cladding. Lead concentrations were high compared to other studies, with 69% of rain-fed tank samples exceeding the World Health Organisation’s health-based guideline of 0.01 mg/L. Further work is required to determine risks of short-term consumption of this water in emergency situations.

This study aimed to optimize the bioelectricity production process using a vinasse solution through the application of Plackett-Burman and Box-Behnken designs. An electrochemical cell was constructed using Arduino to measure the potential difference between the anode and cathode immersed in the vinasse solution, a byproduct of wine production containing organic compounds and ions that undergo redox reactions. The Plackett-Burman design identified the most influential variables among eight previously selected, including vinasse concentration, agitation, and yeast, which positively affected millivolt production, while temperature showed a negative correlation. Based on these results, the Box-Behnken design was used for process optimization, varying parameters such as concentration, stirring, and sodium chloride. Response surface graphs demonstrated the relationship between these variables and millivolt production. The findings indicate that higher agitation levels, lower concentrations of vinasse, and the addition of sodium chloride can enhance bioelectricity generation. The study provides insights into the bioelectricity production process from vinasse, contributing to the understanding and potential for sustainable energy generation. The methodology involving Arduino-based measurement and the utilization of experimental designs offers a systematic approach to optimize bioelectricity production from vinasse.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

B-cell lymphomas (BCL) is the most frequent hematological cancer in dogs. Treatment typically consists of chemotherapy, with CHOP-based protocols. However, outcome remains generally poor, urging the exploration of new therapeutic strategies with a targeted approach. Myc tran-scription factor plays a crucial role in regulating cellular processes and its dysregulation is im-plicated in numerous human and canine malignancies, including canine BCL (cBCL). This study aims to evaluate the efficacy of indirectly inhibiting Myc in cBCL using BI2536 and MZ1 com-pounds in two in vitro models (CLBL-1 and KLR-1201). Both BI2536 and MZ1, alone and com-bined, affected cell viability in a significant concentration and time-dependent manner. Western Blot revealed an upregulation of PLK1 expression in both cell lines upon treatment with BI2536, in association with a reduction in c-Myc protein levels. Conversely, MZ1 led to a decrease in its primary target, BRD4, along with a reduction in c-Myc. Furthermore, BI2536, both alone and in combination with MZ1, induced larger transcriptomic changes in cells compared to MZ1 alone, primarily affecting MYC target genes and genes involved in cell cycle regulation. These data un-derscore the potential role of Myc as therapeutic target in cBCL, providing a novel approach to indirectly modulate this molecule.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Fowlpox virus (FPV) has been used as a vector for many years. To date, surprisingly, very little data exist on the persistence of fowlpox vaccines in chicken tissues, or what kind of immune cells respond to the vaccination at the site of inoculation. Although both humoral and cellular mediated immunity (CMI) play a part in overall immunity against FPV, little is known regarding the cell-mediated immune responses to FPV infection. The main aim of this paper was to measure persistence of the recombinant fowlpox vaccine in the skin tissues following vaccination. The results showed that the recombinant FPVs do not persist for long, and are cleared by 6 days post-vaccination (dpv). The response of immune cells (macrophages, B cells, CD4+ and CD8+ T cells) that infiltrating the site of vaccination was estimated.

Chronic graft-versus-host disease (cGvHD) occurs in 20-50% of recipients following allogeneic haematopoietic stem cell transplantation (allo-HSCT). Corticosteroids (CS) remain the first line treatment but have suboptimal efficacy and carry the risk of long-term side effects. New agents with a better safety profile and higher efficacy, ideally combining immunomodulatory and antifibrotic properties, are urgently needed. From 2016 to 2020, we conducted a phase 2 clinical trial with ATO in chronic GvHD (ClinicalTrials.gov ID NCT02966301 - GMED16-001). This study aimed to evaluate the efficacy and safety of a first-line combination of arsenic trioxide (ATO) and CS in adult patients with cGvHD who require systemic therapy after a first allo-HSCT for a haematological disease. In this prospective, national, multicenter, single-arm, open-label phase II study, conducted in 5 university hospital centers in France, ATO was initiated within 10 days of starting CS at 1 mg/kg/day. Patients received 11 infusions of ATO per 4-week cycle, at a dose of 0.15 mg/kg per infusion. Patients received 1 or 2 cycles of treatment depending on the clinical response and the assessment of the treating physician. The results were published in July 2022 in a paper entitled "High Response Rate and Corticosteroid Sparing with ATO-Based First-Line Therapy in Chronic Graft-versus-Host Disease after Allogeneic Hematopoietic Stem Cell Transplantation". The GMED16-001 study demonstrated convincing efficacy and safety characteristics of the intravenous drug (Trisenox^®/Arscimed^®): the first-line use of ATO in addition to corticosteroids was associated with a high clinical response rate and correlated with rapid corticosteroid (CS) sparing in moderate to severe cGvHD after allo-HSCT. We performed a post-hoc analysis of the data to determine the best schedule for treating cGvHD patients with ATO. Our post-hoc analysis leads us to the conclusion that two cycles of ATO, at 0.15 mg/kg/day, 5 days per week for 4 weeks each, separated by a 4-week therapy-free interval, appears to be the most promising treatment schedule.

The purpose of this study is to investigate the failure mechanism and preventive strengthening methods of prefabricated full length small box girder (PSBG) under car explosion. After damage analysis during blast loads using the commercial software Autodyn, three strengthening methods are presented to improve the blast mitigation performance. The results show that the failure modes and bearing capacity are significantly different with various strengthening measures. Adhering U-shaped steel plate can effectively enhance the shear performance of PSBG under blast loads. Strengthening the bottom of the upper flange of box girder with steel plate can effectively mitigate the local bending failure, and enhance the overall flexural capacity during car explosion.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

Although total nett CO₂ atmospheric flow can be estimated with reasonable accuracy, the contributing gross fluxes between the atmosphere and the earth's surface are poorly understood. This paper presents a method, driven by the objective of simplicity, by which the global outflow and inflow of CO₂ between atmosphere and a globally equivalent "mixing reservoir" can be estimated, using the isotopes ¹⁴C and ¹³C as tracers. It has been asserted that the isotopic carbon in CO₂ cannot be directly used as a tracer in flow studies because it is not subject to the Revelle factor. Evidence is provided showing that this view is mistaken. The model contains 7 key parameters which are used to create synthetic records of Δ¹⁴C and d¹³C spanning 200 years or more, including during the period of atmospheric weapons testing and its decay known as the "bomb pulse". By optimising the fit between these computed values and the historical records of d¹³C and Δ¹⁴C, all seven key parameters are determined. The effective "mixing reservoir" is thereby determined to have a size around six times that of the atmosphere, with global outflux rising from 39.7 GTC yr-1 in 1750 to 58.9 GTC/yr in 2020, this figure probably not including annually cycled carbon.

Pancreatic cancer (PC) is considered one of the most challenging and formidable malig-nancies to treat because it is usually diagnosed at terminal stage, thus it is characterized with a poor prognosis with 5% of patients living over 5 years. The late diagnosis leads to a lower suc-cess rate of resectability, hence chemotherapy or chemoradiotherapy are the only hopes for most PC patients. However, the available drug combinations for PC treatment did not provide satisfactory clinical outcomes. There is a pressing and urgent need to discover new chemothera-peutics which fight PC with tolerable side effects and less liability for resistance. Pentacyclic triterpenes (PTs) are privileged structures with a multitude of biological activities mitigating several ailments, particularly in neoplasm field. They are characterized by a high therapeutic window and their activity can be highly enhanced through structural modifications. Indeed, several parent PTs such as oleanolic acid, ursolic acid, lupeol, betulinic acid, and celastrol proved effective against different PC phenotypes inhibiting their proliferation, invasion, and metastasis mainly via KRAS modulation. Some PTs worked as adjuvant chemosensitizers in gemcitabine-resistant or TRAIL-resistant cells. Owing to their potential in PC treatment, we pre-sent this review article summarizing PC pathogenesis and the promising role of PTs in the man-agement of PC when used either solely or in combination with other chemotherapies such as gemcitabine and 5-Fluorouracil.

This review examines the relationship between blackhole activity and kinematic gas-star misalignment in brightest group galaxies (BGGs) with different merger rates. The formation history of galaxy groups is assessed through "age-dating" as an indicator of distinct major mergers involving the BGG. BGGs within groups characterized by a higher frequency of major mergers are more likely to host active SMBHs. A consistent correlation is identified between the level of black hole activity, as indicated by the 1.4 GHz and 325 MHz radio emissions, and the degree of kinematic misalignment between the gas and stellar components in BGGs. In dynamically relaxed groups, where blackhole accretion rate is relatively (∼1 dex) lower due to the lack of recent ( ≤1 Gyr) major mergers, there is reduced (∼ 30%) misalignment between the gas and stellar components of BGGs compared to unrelaxed groups. Additionally, the study reveals that BGGs in unrelaxed groups show higher levels of star formation rate and increased occurrence of mergers, contributing to observed color differences. Exploring the properties and dynamics of the gas disc influenced by mechanical AGN feedback through hydrodynamic simulations suggests that AGN wind-induced effects further lead to persistent gas misalignment of the disk around the supermassive blackhole.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

How a species is represented by marketers of animal-based products both reflects and shapes how consumers think about that animal. By examining the explicit statements, and implicit messages encoded in the imagery on supermarket egg boxes, this paper explores how hens are represented by whole egg retailers. Content analysis reveals two prominent messages purveyed through eggbox graphics, namely those pertaining to hen welfare and human health. The later disenfranchises hens from their products by focusing on the nutritional value of eggs, whereas the former reflects a public concern for the welfare of egg-laying hens. Although claims of improvements in welfare practices are undoubtedly exploited as marketing tools, they serve to raise awareness and drive competitors to adopt similar practices. Welfare claims are a direct response to public concerns about the plight of hens, and may positively influence industry welfare standards. However, idyllic depictions displayed on eggboxes also lull consumers into the belief that those eggs are an ethically sound food choice, regardless of the actual standard of living experienced by the hens.

In this paper, we establish some inequalities bounding the ratio Г_p,k(x)/Г_p,k(y), where Г_p,k(.) is the (p,k)-analogue of the Gamma function. Consequently, some previous results are recovered from the obtained results.

Aims/Hypothesis): Type 1 diabetes is an immune-mediated disease with destruction of the pancreatic β-cells, a process that is conditioned by multiple genes and other factors. HLA counts as the major susceptibility gene. Significant variations in HLA genetic susceptibility to type 1 diabetes between Caucasians, African and Asian and other ethnic groups may have led to the variation in incidence of type 1 diabetes globally. Type 1 diabetes is characterized upon HLA identification. In this chapter we discuss global variations in genetic susceptibility of HLA with regard to type 1 diabetes globally with a particular attention to Arab population. Methods): Haplotype configuration of HLA class I A, B, C and Class II –DR/DQ/DP were studied in Caucasians, African and Asian and in Arab population to see if that is responsible for the exponential rise in the rate of type 1 diabetes. Results): Although Arabs have one of the highest global incidence and prevalence rates of type 1 diabetes, unfortunately, there is a dearth amount of information regarding HLA genetic susceptibility to type 1 diabetes in the Arab world. HLA haplotype configurations contribute to its risk value. However, out of an insufficient present study there are examples of misjudgment of HLA risk according to HLA alleles rather than haplotypes. Conclusion): To date HLA outlooks for the characterization of type 1 diabetes. There is an ethnicity difference in HLA characteristics which is responsible for variation in type 1 diabetes. Although Arab population have contributed heavily in the rise of burden of type 1 diabetes, however, there is significantly a dearth amount of studies on HLA in Arab population. Obviously, any future prediction, prevention or cure of the disease will be based on the HLA genetics. There is a dire need for a systematic screening of HLA for Arab population with type 1 diabetes, identification of Arab HLA-risk values and identify those who are prone to get the disease.

This article is a study on the (k,s)-Riemann-Liouville fractional integral, a generalization of the Riemann-Liouville fractional integral. Firstly, we introduce several properties of the extended integral of continuous functions. Furthermore, we make the estimation of the Box dimension of the graph of continuous functions after the extended integral. It presents that the upper Box dimension of the (k,s)-Riemann-Liouville fractional integral for any continuous functions is no more than the upper Box dimension of the functions on the unit interval I=[0,1], which indicates that the upper Box dimension of the integrand f(x) will not be increased by the σ-order (k,s)-Riemann-Liouville fractional integral ksD−σf(x) where σ&gt;0 on I. Additionally, we prove that the fractal dimension of ksD−σf(x) of one-dimensional continuous functions f(x) is still one.

Background: Good clinical practice (GCP) training is the industry standard for ensuring the quality conduct of registrational clinical trials. However, concerns have been raised about whether the current structure and delivery of GCP training sufficiently prepares clinical investigators and their delegates to conduct clinical trials. Methods: We conducted qualitative semi-structured interviews with 13 clinical investigators and 10 research sponsors to 1) examine characteristics of the quality conduct of sponsored clinical trials, including critical tasks and concerns perceived as essential for trial quality, 2) identify key knowledge and skills required to perform critical tasks, and 3) identify gaps and redundancies in GCP training and areas of improvement to ensure the quality conduct of clinical trials. We used applied thematic analysis to analyze the data. Results: The top three tasks identified as critical for the quality conduct of clinical trials were obtaining informed consent, ensuring protocol compliance, and protecting participants’ health and safety. Respondents acknowledged that GCP principles address each of these critical tasks; however, they described many challenges and burdens of GCP training, including high training frequency and repetitive content. Respondents suggested moving beyond GCP training as a mere check-box activity by making it more effective, engaging, and interactive. They also emphasized that applying GCP principles in a real-world, skills-based environment would increase the relevance of GCP training to investigators and their delegates. Conclusion: Our findings indicate that although investigators and sponsors recognize that GCP training addresses critical tasks necessary to the quality conduct of clinical trials, they articulated the need for significant improvement in the design, content, and presentation of GCP training.

This paper uses probability method to evaluate the fire safety performance of prestressed steel-concrete beam bridges based on simulation experimental research. Firstly, fire simulation experimental sample analysis was conducted on actual small box girder bridges to obtain the structural response of prestressed steel-concrete structures under fire, which is in line with engineering practice. Next, construct a reliability analysis model for the fire resistance performance of prestressed steel-concrete beam bridges; Combining reliability theory with finite element method, establish a reliability analysis method for the fire resistance performance of prestressed steel-concrete beam bridges. Subsequently, a safety factor evaluation model for the fire resistance performance of prestressed steel-concrete beam bridges was proposed, and a safety factor evaluation method for the fire resistance performance of prestressed steel-concrete beam bridges based on reliability back analysis was established. Finally, based on the analysis of the structural response after a fire in a specific case of a simply supported to continuous prestressed steel-concrete continuous beam bridge project, a structural resistance sample of the prestressed steel-concrete beam bridge is generated through uniform design method, and statistical analysis is conducted. Subsequently, probability methods are used to evaluate the safety of the prestressed steel-concrete beam bridge after a fire. Through analysis, it can be concluded that the time of fire has a significant impact on the structural performance of prestressed steel-concrete beam bridges, and the randomness of parameters has a significant impact on the safety reserve of prestressed steel-concrete beam bridges after fire. It is necessary to pay attention to it in specific engineering practice and strengthen the monitoring and statistics of structural random characteristics.

The integration of deep learning methods, especially Convolutional Neural Networks (CNN), and Synthetic Aperture Radar Automatic Target Recognition (SAR ATR) has been widely deployed in the field of radar signal processing. Nevertheless, these methods are frequently regarded as black-box models due to the limited visual interpretation of their internal feature representation and parameter organization. In this paper, we propose an innovative approach named C-RISE, which builds upon the RISE algorithm to provide a post-hoc interpretation technique for black-box models used in SAR Images Target Recognition. C-RISE generates saliency maps that effectively visualize the significance of each pixel. Our algorithm outperforms RISE by clustering masks that capture similar fusion features into distinct groups, enabling more appropriate weight distribution and increased focus on the target area. Furthermore, we employ Gaussian blur to process the masked area, preserving the original image structure with optimal consistency and integrity. C-RISE has been extensively evaluated through experiments, and the results demonstrate superior performance over other interpretation methods based on perturbation when applied to neural networks for SAR image target recognition. Furthermore, our approach is highly robust and transferable compared to other interpretable algorithms, including white-box methods.

The important sampling parameters of a headspace solid phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS) procedure, extraction temperature, extraction time and sample volume were optimized to quantify 23 important impact odorants in reduced alcohol red and white wines. A three-factor design of Box-Behnken experiments was used to determine optimized sampling conditions for each analyte, and a global optimized condition at every ethanol concentration of interest determined using a desirability function that accounts for a low signal response for compounds. Shiraz and Chardonnay wines were dealcoholized from 13.7 and 12.2% v/v ethanol respectively, to 8 and 5% v/v, using a commercially available membrane-based technology. A sample set of the reduced alcohol wines were also reconstituted to their natural ethanol level to evaluate the effect of ethanol content reduction on volatile composition. The three-factor Box-Behnken experiment ensured an accurate determination of the headspace concentration of each compound at each ethanol concentration, allowing comparisons between wines at varying ethanol levels to be made. Overall, the results showed that the main effect of extraction temperature was considered the most critical factor when studying the equilibrium of reduced alcohol wine impact odorants. The impact of ethanol reduction upon the concentration of volatile compounds clearly resulted in losses of impact odorants from the wines. The concentration of most analytes decreased with dealcoholization compared to that of the natural samples. Significant differences were also found between the reconstituted volatile composition and 5% v/v reduced alcohol wines, revealing that the dealcoholization effect is the result of a combination between the type of dealcoholization treatment and reduction in wine ethanol content.

The microbial contamination in food packaging have been a major concern that paved the way for the search for natural based new anti-microbial agents, such as modified α-mangostin. In the present work, twelve synthetic analogs were obtained via semi-synthetic modification of α-mangostin by Ritter reaction, reduction by palladium-carbon (Pd-C), alkylation, and acetylation. The evaluation of the anti-microbial potential of the synthetic analogs showed higher therapeutic value than the parent molecule. The anti-microbial studies proved that I E showed higher antibacterial activity whereas I I showed most significant antifungal activity. Due to their microbial properties, modified α-mangostin can be utilized as active anti-microbial agents in food packaging.

We report on the design, characterization and validation of a spherical irradiation system for inactivating SARS-CoV-2, based on UV-C 275 nm LEDs. The system is designed to maximize ir-radiation intensity and uniformity, and can be used for irradiating a volume of 18 liters. To this aim: (i) several commercially available LEDs have been acquired and analyzed; (ii) a complete optical study has been carried out in order to optimize the efficacy of the system. (iii) The re-sulting prototype has been characterized optically, and tested for the inactivation of SARS-CoV-2 for different exposure times, doses and surface types. Results indicate that a 99.9% inactivation can be reached after 1 minute of treatment with a dose of 83.1 J/m2.

For decades, compounds present in foods and beverages have been implicated in the etiology of human cancers. The International Agency for Research on Cancer (IARC) continues to classify such agents regarding their potential carcinogenicity in humans based on new evidence from animal and human studies. Furfuryl alcohol and β-myrcene belong to these potential human carcinogens due to be evaluated. The major source of furfuryl alcohol in foods is thermal processing and ageing of alcoholic beverages while β-myrcene occurs naturally as a constituent of essential oils of plants such as hops, lemongrass and derived products. This study aimed to summarize the occurrence of furfuryl alcohol and β-myrcene in foods and beverages using data from own nuclear magnetic resonance (NMR) analysis and literature review. The highest content of furfuryl alcohol was found in coffee beans (>100 mg/kg) and in some fish products (about 10 mg/kg) while among beverages, wines contained between 1–10 mg/L with 8 mg/L in pineapple juice. The content of β-myrcene was highest in hops. In conclusion, the data about the occurrence of the two agents is either very old or based on single sample analysis, and currently judged as insufficient for exposure and risk assessment. The results of this study point out the food and beverage groups that may be considered for future monitoring of furfuryl alcohol and β-myrcene.