As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

At present, indoor localization is one of the core technologies of location-based services (LBS), and there exist numerous scenario-oriented application solutions. Visual features, as the main semantic information to help people understand the environment and thus occupy the dominant part, many techniques about indoor scene recognition are widely adopted. However, the engineering application problem of cell phone indoor scene recognition and localization has not been well solved due to insufficient semantic constraint information of building map and the immaturity of building map location anchors (MLA) matching positioning technology. To address the above problems, this paper proposes a cell phone indoor scene recognition and localization method with building map semantic constraints. Firstly, we build a library of geocoded entities for building map location anchors (MLA), which can provide users with "immersive" real-world building maps on the one hand and semantic anchor point constraints for cell phone positioning on the other. Secondly, using the improved YOLOv5s deep learning model carried on the mobile terminal, we recognize the universal map location anchors (MLA) elements in building scenes by cell phone camera video in real-time. Lastly, the spatial location of the scene elements obtained from the cell phone video recognition is matched with the building MLA to achieve real-time positioning and navigation. The experimental results show that the model recognition accuracy of this method is above 97.2%, and the maximum localization error is within the range of 0.775 m, and minimized to 0.5 m after applying the BIMPN road network walking node constraint, which can effectively achieve high positioning accuracy in the building scenes with rich MLA element information. In addition, the building map location anchors (MLA) has universal characteristics, and the positioning algorithm based on scene element recognition is compatible with the extension of indoor map data types, so this method has good prospects for engineering applications.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The role of natural factors mainly solar eleven-year cycle variability, and volcanic eruptions on two major modes of climate variability the North Atlantic Oscillation (NAO) and El Niño Southern Oscillation (ENSO) are studied for around last 150 years period. The NAO is the primary factor to regulate Central England Temperature (CET) during winter throughout the period, though NAO is impacted differently by other factors in various time periods. Solar variability indicates a strong positive influence on NAO during 1978-1997, though suggests opposite in earlier period. Solar NAO lag relationship is also shown sensitive to the chosen times of reference and thus points towards the previously proposed mechanism/ relationship related to the sun and NAO. The ENSO is influenced strongly by solar variability and volcanic eruptions in certain periods. This study observes a strong negative association between the sun and ENSO before the 1950s, which is even opposite during the second half of 20th century. The period 1978-1997, when two strong eruptions coincided with active years of strong solar cycles, the ENSO, and volcano suggested a stronger association, and we discussed the important role played by ENSO. That period showed warming in central tropical Pacific while cooling in the North Atlantic with reference to the later period (1999-2017) and also from chosen earlier period. Here we show that the mean atmospheric state is important for understanding the connection between solar variability, the NAO and ENSO and associated mechanism. It presents a critical analysis to improve knowledge about major modes of variability and their role in climate. We also discussed the importance of detecting the robust signal of natural variability, mainly the sun.

A flow chart is presented depicting coupling in ocean-atmosphere system, initiated by solar decadal variability that involves El Niño Southern Oscillation (ENSO). Possible mechanisms for Canonic ENSO, Modoki ENSO and Canonic-Modoki ENSO are proposed considering their relevance to the decadal variation of Hadley, Walker circulation and mid-latitude jets. It also discusses subsequent teleconnections by ENSO on Indian Summer Monsoon (ISM) with a special emphasis on later two decades of the last century. Possible mechanisms relating to a disruption of the usual ENSO-ISM teleconnection for those decades are emphasised; the role of volcanos and the change in the sun- NAO (North Atlantic Oscillation) connection were attended. The regional Hadley circulation, via the NAO in the northern hemisphere and Indian Ocean Dipole in the southern hemisphere, during that period, may have a role in the change in ISM behaviour- which though captured in observation but missed by models. The representation of flow chart helps to improve understanding of various types of ENSO in both temporal as well as spatial scale. The overall study subsequently can benefit the modelling community by not only improved the representation of ENSO in models but also better representation of ISM teleconnection via regional Hadley cell.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

In August 4 2011, United Nations Environmental Program (UNEP) submitted an unprecedented, scientific, groundbreaking Environmental Assessment Report (EAR) of Ogoniland, to the Nigerian government. This was the outcome of a 14–month intensive evaluation of the extent of pollution. It was intended that UNEP’s recommendations would be implemented to restore the devastated environment, on the one hand, and on the other, counteract the numerous environmental health issues that have for decades, plagued Ogoniland. However, five years post EAR, and, despite the seriousness of the situation, no significant resolution has occurred, both on the part of the government, and on the part of Shell Petroleum Development Company (SPDC) or Shell. To date, millions of Niger Delta residents, particularly those living in the oil-bearing communities, continue to suffer severe consequences. Although, the assessment was conducted in Ogoniland, other communities in the Niger Delta are also affected. This article explores prevailing issues, using Ogoniland (a microcosm of the Niger Delta) as an example. A multidisciplinary approach for sustainable mitigation of environmental health risks in the Niger Delta is paramount, and Environmental Management tools offer valuable strategies. Adopting UNEP’s recommendations for addressing environmental health problems requires implementing the Environmental Management/Environmental Management System (EM/EMS) model.

The objective of this research is to establish a better understanding of the current landscape of digital learning research and sustainable development by using CiteSpace. First, we retrieved published publications from the Web of Science (2004–2022). Following that, we examined the primary research strengths and important subjects of digital learning from two perspectives: collaboration networks (including collaborative networks across countries, institutions, and authors) and co-citation networks. We examined the co-citation network from three perspectives: cluster analysis, the most active citers, top references. Furthermore, referenced journals, popular themes, and rising trends were examined. These findings indicate the primary study subjects in the field of digital learning, the most intriguing research literature, and each period's emerging research hotspots. Finally, we proposed further study ideas for future paths.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

The carbohydrate antigen Sda is expressed on cells and secretions of the vast majority of Caucasians. The epitope is formed by a terminal GalNAc residue β4-linked to a α3-sialylated galactose. Different carbohydrate chains N- or O-linked to glycoproteins can be terminated by this epitope. The final step of Sda biosynthesis is catalyzed by the GalNAc transferase B4GALNT2. In this review, we will discuss the multifaceted aspects of B4GALNT2/Sda biology. In particular, we will see its implications in fertility and pregnancy, in susceptibility to infectious diseases, in chronic kidney diseases and in Duchene muscular dystrophy. In particular, we will show its regulation and prognostic implications in cancer.

Cholangiocellular carcinoma (CCA) is the second most common primary liver cancer, with increasing incidence worldwide and inadequate therapeutic options. Intra- and extrahepatic bile ducts have distinctly different embryonic origins and developmental behavior, and accordingly intra- and extrahepatic CCAs (ICC vs. ECC) are molecularly different. A promising strategy in oncotherapy is targeted therapy, targeting proteins that regulate cell survival and proliferation; such as the MAPK/ERK and PI3K/AKT/mTOR signaling pathways. Inhibitors of these pathways have been tested previously in CCA cell lines. However, these cell lines could not be clearly assigned to ICC or ECC, and results indicated apoptosis induction by targeted therapeutics. We tested targeted therapeutics (selumetinib, MK2206) in three defined ICC cell lines (HuH28, RBE, SSP25). We observed cooperative effects of dual inhibition of the two pathways, in accordance with inhibition of phospho-AKT and phospho-ERK1/2 expression. Proliferation was blocked more effectively with dual inhibition than with each single inhibition, but cell numbers did not drop below baseline. Accordingly, we observed G1-phase arrest, but not apoptosis (cleaved caspase-3, AIFM1 regulation, subG1-phase) or necroptosis (phospho-MLKL). We conclude that dual inhibition of MAPK/ERK and PI3K/AKT/mTOR pathways is highly effective to block proliferation of ICC cell lines, but therapy must certainly be supplemented with standard therapies.

Reducing the levels of toxic chemicals that cause adverse health and environmental impacts is a challenge for the international community. There is a need of a global strategy. Indeed, too often the problems associated to the exposure of chemical substances is recognized a posteriori, in the presence of consequences already observed. The prediction of the likely effects of chemical exposure on human health is based on classical tests with animals, which are time and money consuming, may deviate from an accurate prediction towards humans, and arises ethical concerns. Regulations are now considering the adoption of in silico (or computational) methods, which can be used for prioritizing substances according to the probability to be toxic for the biosphere. Several initiatives have prioritized chemicals, typically based according to some criteria, such as chemicals which may be endocrine disruptors, or persistent, bioaccumulative, or toxic (PBT). However, these initiatives focused on a certain range of adverse properties, and covered a certain number of substances only. We applied a set of largely validated and widely used predictive methods to large collections of chemicals: (i) to about 340,000 with a defined function, and (ii) to about 6 millions, which have been synthetized. The aim of this study is to quantify the putative impact of existing and future chemicals on towards human health, ecological and environment properties. The impact on the environment is the cause of major concern. This is the case of pesticides and hazardous, which is quite expected; however, also pharmacologically active candidate compounds of natural origin may have a high level of ecotoxicity. Pesticides and hazardous are also the categories of higher concern for humans, followed by pharmaceuticals. The pesticides and the hazardous are the categories of higher concern also on the environmental point of view. The results of our analysis could be the basis for the identification of new safety rules.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Historical maps constitute unique sources of retrospective geographic information. Recently, several map archives containing map series covering large spatial and temporal extents have been systematically scanned and made available to the public. The geographic information contained in such data archives allows extending geospatial analysis retrospectively beyond the era of digital cartography. However, given the large data volumes of such archives and the low graphical quality of older map sheets, the processes to extract geographic information need to be automated to the highest degree possible. In order to understand the salient characteristics, data quality variation, and potential challenges in large-scale information extraction tasks, preparatory analytical steps are required to efficiently assess spatio-temporal coverage, approximate map content, and spatial accuracy of such georeferenced map archives across different cartographic scales. Such preparatory steps are often neglected or ignored in the map processing literature but represent highly critical phases that lay the foundation for any subsequent computational analysis and recognition. In this contribution we demonstrate how such preparatory analyses can be conducted using classical analytical and cartographic techniques as well as visual-analytical data mining tools originating from machine learning and data science, exemplified for the United States Geological Survey topographic map and Sanborn fire insurance map archives.

Industrial hemp (Cannabis sativa L.) is an attractive candidate for sustainable pest management due to its abundance of bioactive compounds with potential pesticidal properties. Solvent choice has a significant impact on the extraction efficiency of bioactive compounds. Deep Eutectic Solvents (DESs) are gaining popularity in extraction because they are safe and environmentally friendly, making them viable alternatives to organic solvents (OSs). This research first compared the extraction efficiency of OSs on the extraction of phytochemicals from the infloresences of two hemp varieties, Citrus and Cherry Dwarf. Inflorescences were extracted using three OSs, ethanol, ethyl acetate, and hexane. The highest level of cannabidiol (CBD; 0.69%) was extracted from Cherry Dwarf using ethanol while the level of delta-9 tetrahydrocannabinol THC (0.19%) was essentially the same in both. Therefore, Cherry Dwarf was selected to compare the extraction efficiency of DESs to the OSs. The DESs were choline chloride/ethylene glycol, citric acid/ethylene glycol, menthol/lauric acid, choline chloride/urea and choline chloride/glycerol. In the targeted analysis, choline chloride/ethylene glycol extracted the highest amount of CBD (0.87%) followed by choline chloride/urea (0.78%). As some DESs outperformed ethanol, the popular solvent for extracting cannabinoids, DESs are viable candidates to replace organic solvents.

Chronic graft-versus-host disease (cGvHD) occurs in 20-50% of recipients following allogeneic haematopoietic stem cell transplantation (allo-HSCT). Corticosteroids (CS) remain the first line treatment but have suboptimal efficacy and carry the risk of long-term side effects. New agents with a better safety profile and higher efficacy, ideally combining immunomodulatory and antifibrotic properties, are urgently needed. From 2016 to 2020, we conducted a phase 2 clinical trial with ATO in chronic GvHD (ClinicalTrials.gov ID NCT02966301 - GMED16-001). This study aimed to evaluate the efficacy and safety of a first-line combination of arsenic trioxide (ATO) and CS in adult patients with cGvHD who require systemic therapy after a first allo-HSCT for a haematological disease. In this prospective, national, multicenter, single-arm, open-label phase II study, conducted in 5 university hospital centers in France, ATO was initiated within 10 days of starting CS at 1 mg/kg/day. Patients received 11 infusions of ATO per 4-week cycle, at a dose of 0.15 mg/kg per infusion. Patients received 1 or 2 cycles of treatment depending on the clinical response and the assessment of the treating physician. The results were published in July 2022 in a paper entitled "High Response Rate and Corticosteroid Sparing with ATO-Based First-Line Therapy in Chronic Graft-versus-Host Disease after Allogeneic Hematopoietic Stem Cell Transplantation". The GMED16-001 study demonstrated convincing efficacy and safety characteristics of the intravenous drug (Trisenox^®/Arscimed^®): the first-line use of ATO in addition to corticosteroids was associated with a high clinical response rate and correlated with rapid corticosteroid (CS) sparing in moderate to severe cGvHD after allo-HSCT. We performed a post-hoc analysis of the data to determine the best schedule for treating cGvHD patients with ATO. Our post-hoc analysis leads us to the conclusion that two cycles of ATO, at 0.15 mg/kg/day, 5 days per week for 4 weeks each, separated by a 4-week therapy-free interval, appears to be the most promising treatment schedule.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

Recently we have seen a relaxation of the historic restrictions on the use and subsequent research on the Cannabis plants, generally classified as Cannabis sativa and Cannabis indica. What research has been performed to date has centered on chemical analysis of plant flower products, namely cannabinoids and various terpenes that directly contribute to phenotypic characteristics of the female flowers. In addition, we have seen many groups recently completing genetic profiles of various plants of commercial value. To date, no comprehensive attempt has been made to profile the proteomes of these plants. We report herein our progress on constructing a comprehensive draft map of the Cannabis proteome. To date we have identified over 17,000 potential protein sequences. Unfortunately, no annotated genome of Cannabis plants currently exists. We present a method by which “next generation” DNA sequencing output and shotgun proteomics data can be combined to produce annotated FASTA files, bypassing the need for annotated genetic information altogether in traditional proteomics workflows. The resulting material represents the first comprehensive annotated protein FASTA for any Cannabis plant. Using this annotated database as reference we can refine our protein identifications, resulting in the confident identification of 13,000 proteins with putative function. Furthermore, we demonstrate that post-translational modifications play an important role in the proteomes of Cannabis flower, particularly lysine acetylation and protein glycosylation. To facilitate the evolution of analytical investigations into these plant materials, we have created a portal to host resources we have developed from proteomic and metabolomic analysis of Cannabis plant material as well as our results integrating these resources. All data for this project is available to view or download at www.CannabisDraftMap.Org

As new vaccines reduce P. falciparum (Pf) cases, clinicians can focus on rescuing more children with cerebral malaria (CM). Adjunctive “therapeutically-rational exchange transfusion” (T-REX) refers to using special “Pf-resistant” donor red blood cells (RBCs) that secrete nano-sized RBC extracellular vesicles (EVs). Can some RBC EVs rapidly dislodge Pf-infected RBCs (iRBCs) sequestered in blood vessels and reduce inflammation? Does post-exchange “rebound parasitemia” reflect sequestration-reversal? We reviewed case-reports, EV and liposome studies, expert perspectives, and time-sequence data. In the AQUAMAT study, median coma-recovery time was 20 hours for artesunate. In contrast, a CM patient treated with type-O T-REX quickly began speaking (during the procedure). For other rapid-recovery CM patients, donor RBC variables had not been specified. Despite rapid Pf-killing, drugs need 20 hours to substantially reduce iRBC cytoadhesion while EVs can selectively bind distant inflamed tissues within 15 minutes. RBCs stressed by blood-bank storage and Pf infection secrete EVs. Post-exchange “rebound parasitemia” can occur within 60 minutes and may reflect release of sequestered iRBCs. Sequestration-reversal can be assessed by monitoring Pf parasitemia and total Pf biomass. New data suggest clinicians, working with transfusion- and laboratory-medicine physicians, can, and should, assess T-REX options and publish their findings to help clarify how RBC EVs may serve as therapeutic “decoy ligands.”

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

Image encryption based on chaotic maps is an important way to ensure the secure communication of digital multimedia on the Internet. To improve the encryption performance and security of image encryption systems, a new image encryption algorithm is proposed by employing a compound chaotic map and random cyclic shift. Firstly, an improved Hybrid chaotic system is designed by coupling Logistic, ICMIC, Tent, and Chebyshev maps (HLITC). Comparison tests with previous chaotic maps in terms of chaotic trajectory, Lyapunov exponent, and Kolmogorov entropy illustrate the new hybrid chaotic map has better chaotic performance. Then the proposed HLITC chaotic system is used to develop a new chaotic image encryption scheme with the double cyclic shift. The improved HLITC chaotic system is performed to generate key sequences used in the image scrambling and diffusion stage. The spiral transformation controlled by chaotic sequence is used to scramble the pixels of the plaintext image, while the XOR operation based on a chaotic map is used for pixel diffusion. Extensive experiments of statistical analysis, key sensitivity, and keyspace analysis are conducted. Experimental results show the proposed encryption scheme has good robustness against brute force attacks, statistical attacks, and differential attacks, and is more effective than many existing chaotic image encryption algorithms.

Cyberspace map, as one of the important tools to describe cyberspace, gives an image to the unpredictable and illusory cyberspace, and has become a research hotspot in the fields of cartography, cyberspace security. Clarifying the concept of cyberspace map and constructing the conceptual model of cyberspace map can promote people's unified cognition of cyberspace. Based on the view of cartography, this paper compares and analyzes some related concepts of cyberspace map, discusses the characteristics of cyberspace map，and gives its concept. After that, it analyzes people's cognition of cyberspace composition. On this basis, it caters to this cognition mode and proposes the conceptual model of cyberspace map. Then, the connotation of the model is elaborated from three aspects: element-space association dimension, element mapping dimension and the map representation dimension. Finally, the specific composition and symbolization of various elements are analyzed. The model provides the top-level framework and theoretical guidance for the research of cyberspace map. This paper aims to adapt to the development trend of Cartography in ternary space, clarify the basic concept of cyberspace map, promote the development of cyberspace mapping theory, and lay the foundation for subsequent research.

We describe a vision for a national-scale heavy mineral (HM) map generated through automated mineralogical identification and quantification of HMs contained in floodplain sediments from large catchments covering most of Australia. The composition of the sediments reflects the dominant rock types in each catchment, with the generally resistant HMs largely preserving the mineralogical fingerprint of their host protoliths through the weathering-transport-deposition cycle. Heavy mineral presence/absence, absolute and relative abundance, and co-occurrence are metrics useful to map, discover and interpret catchment lithotype(s), geodynamic setting, magmatism, metamorphic grade, alteration or mineralization. Underpinning this vision is a pilot project, focusing on a subset of the national sediment sample archive, which is used to demonstrate the feasibility of the larger, national-scale project. We preview a bespoke, cloud-based mineral network analysis (MNA) tool to visualize, explore and discover relationships between HMs as well as between them and geological setting or mineral deposits. We envisage that the Heavy Mineral Map of Australia and MNA tool will contribute significantly to mineral prospectivity analysis and modeling here, particularly for technology critical elements and their host minerals, which are central to the global economy transitioning to a more sustainable, decarbonized paradigm.

In this paper the D 3 dihedral logistic map of fractional order is introduced. The map 1 presents a dihedral symmetry D 3 . It is numerically shown that the construction and interpretation 2 of the bifurcation diagram versus the fractional order require special attention. The system stability 3 is determined and the problem of hidden attractors is analyzed. Also, analytical and numerical 4 results show that the chaotic attractor of integer order, with D 3 symmetries, looses its symmetry 5 in the fractional-order variant.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

In the past few decades, the transmission of data over an unsecure channel resulted in an increased rate of hacking. Therefore, the requirement to make multimedia data more secure is increasing day by day. Numerous algorithms are developed to improve efficiency and robustness. In this article, a novel and secure image encryption algorithm is presented. It is based on a modified chaotic logistic map (CLM) that provides the advantage of having less computational time to encrypt an input image. The encryption algorithm is based on Shannon’s idea of using substitution-permutation and one-time-pad network to achieve ideal secrecy. The CLM is used for substitution and permutation to improve randomness and increase dependency on the encryption key. Various statistical tests are conducted, such as Key Space Analysis, Complexity Analysis, Sensitivity Analysis, Strict Avalanche Criteria (SAC), Histogram Analysis, Entropy Analysis, Mean of Absolute Deviation (MAD) Analysis, Correlation Analysis, Contrast Analysis, and Homogeneity to give a comparative analysis of the proposed algorithm and verify its security. As a result of various statistical tests, it is evident that the proposed algorithm is more efficient and robust as compared to previous ones.

By constructing a static map, the library robot can navigate and access documents autonomously, which greatly improves efficiency; however, for libraries where shelves can be moved, map changes do not allow for direct navigation, and also sensors such as radar and camera are relatively expensive, so we propose a low-cost navigation algorithm based on real-time ranging data and map matrices, and designed a mobile archive access robot. In order to obtain real-time distance data, nine near/long range sensors were mounted on the chassis and a composite digital filtering algorithm was designed based on different moving area characteristics; then the access task matrix and map matrix were designed based on the archive access task and the location characteristics of the archive shelf placement, the robot can rely on the range data to update the map matrix during the moving process, complete its own positioning, and use the task matrix The robot can use the task matrix to complete autonomous navigation and access to multiple files. Experiments show that the filtered positioning accuracy can reach 1cm, while the robot can move to the target shelf autonomously, which is more practical and less costly.

Quantum tunneling in a two-dimensional integrable map is studied. The orbits of the map are all confined to the curves specified by the one-dimensional Hamiltonian. It is found that the behavior of tunneling splitting for the integrable map and the associated Hamiltonian system is qualitatively the same, with only a slight difference in magnitude. However, the tunneling tails of the wave functions, obtained by superposing the eigenfunctions that form the doublet, exhibit significant difference. To explore the origin of the difference, we observe the classical dynamics in the complex plane and find that the existence of branch points appearing in the potential function of the integrable map could play the role for yielding non-trivial behavior in the tunneling tail. The result highlights the subtlety of quantum tunneling, which cannot be captured in nature only by the dynamics in the real plane.

Many studies in the field of robot navigation have focused on environment representation and localization. The goal of map representation is to summarize spatial information in topological and geometrical abstracts. By providing strong priors, maps improve the performance and reliability of automated robots. Due to the transition to fully automated driving in recent years, there has been a constant effort to design methods and technologies to improve the precision of road participants and the environment's information. Among these efforts is the High Definition (HD) Map concept. Making HD maps requires accuracy, completeness, verifiability, and extensibility. Because of the complexity of HD mapping, it is currently expensive and difficult to implement, particularly in an urban environment. In an urban traffic system, the road model is at least a map with sets of roads, lanes, and lane markers. While more research is being dedicated to mapping and localization, a comprehensive review of the various types of map representation is still required. This paper presents a brief overview of map representation, followed by a detailed literature review of HD Map for automated vehicles. The current state of AV mapping is encouraging, the field has matured to a point where detailed maps of complex environments are built in real-time and have been proved useful. Many existing techniques are robust to noise and can cope with a large range of environments. Nevertheless, there are still open problems for future research. AV mapping will continue to be a highly active research area essential to the goal of achieving full autonomy.

Landscapes evolve due to climatic conditions, tectonic activity, geological features, biological activity, and sedimentary dynamics. These processes link geological processes at depth to surface features. Consequently, the study of landscapes can reveal essential information about the geochemical footprint of ore deposits at depth. Advances in satellite imaging and computing power have enabled the creation of large geospatial datasets, the sheer size of which necessitates automated processing. We describe a methodology to enable the automated mapping of landscape pattern domains using machine learning (ML) algorithms. From a freely available Digital Elevation Model, derived data, and sample landclass boundaries provided by domain experts, our algorithm produces a dense map of the model region in Western Australia. Both random forest and support vector machine classification achieve about 98\% classification accuracy with reasonable runtime of 48 minutes on a single core. We discuss computational resources and study the effect of grid resolution. Larger tiles result in a more contiguous map, while smaller tiles result in a more detailed, and at some point, noisy map. Diversity and distribution of landscapes mapped in this study support previous results. In addition, our results are consistent with the geological trends and main basement features in the region.

Some of the most promising small molecule toxins used to generate antibody drug conjugates (ADCs) include anti-mitotic agents (e.g auristatin and its derivatives) which are designed to attack cancerous cells at their most vulnerable state during mitosis. We were interested to identify a human cystostatic protein eventually showing comparable activities and allowing the generation of corresponding targeted fully human cytolytic fusion proteins. Recently, we identified the human microtubule associated protein tau (MAP tau) which binds specifically to tubulin and modulates the stability of microtubules thereby blocking mitosis and presumably vesicular transport. By binding and stabilizing polymerized microtubule filaments, MAP tau-based fusion proteins skew microtubule dynamics towards cell cycle arrest and apoptosis. This biological activity makes rapidly proliferating cells (e.g cancer and inflammatory cells) an excellent target for MAP tau-based targeted treatments. Their superior selectivity for proliferating cells confers additional selectivity towards upregulated tumor-associated antigens at their surface, thereby preventing off-target related toxicity against normal cells bearing tumor-associated antigens at physiologically normal to low levels. In this review, we highlight recent findings on MAP tau-based targeted cytolytic fusion proteins reported in preclinical immunotherapeutic studies.

Large office buildings are responsible for a substantial portion of energy consumption in urban districts. However, thorough assessments regarding the Nordic countries are still lacking. In this paper we analyse the largest dataset to date for a Nordic office building, by considering a case study located in Stockholm, Sweden, that is occupied by nearly a thousand employees.Distinguishing the lighting and occupants’ appliances energy use from heating and cooling, we can estimate the impact of occupancy without any schedule data. A standard frequentist analysis is compared with Bayesian inference, and the according regression formulas are listed in tables that are easy to implement into building performance simulations (BPS). Monthly as well as seasonal correlations are addressed, showing the critical importance of occupancy.A simple method, grounded on the power drain measurements aimed at generating boundary conditions for the BPS, is also introduced; it shows how, for this type of data and number of occupants, no more complexities are needed in order to obtain reliable predictions. For an average year, we overestimate the measured cumulative consumption by only 4.7%. The model can be easily generalised to a variety of datasets.

This research explores the behaviors of Generation Z consumers in China, particularly focusing on their interaction with companies through social media for the joint creation of value. Adopting a qualitative methodology, the research initially constructs a scale for assessing co-creation of value on social media platforms. Subsequently, it delves into the motivational aspects of users' engagement in these co-creative activities. The study unveils a range of utilitarian and hedonic motivations that drive Generation Z's value co-creation actions on social media. Insights derived from the findings offer both theoretical and practical implications for the field.

The energy efficiency of existing buildings is a crucial factor in addressing Europe’s energy con-sumption challenges, accounting for nearly 40% of the total energy usage. The ongoing energy crisis, driven by the reliance on fossil fuels and increasing prices, has underscored the urgency of adopting sustainable and energy efficient practices especially to the existing building stock. Cyprus is par-ticularly vulnerable due to its heavy dependence on imported fuels for electricity generation and faces significant challenges in transforming its existing building stock into energy-efficient and sustainable structures. Extensive focus has been made by the government on the energy-efficient retrofit of non-residential public buildings. This study examines an existing cultural hall. The case study of the Cultural Hall represents the building stock before 2010 which is lacking thermal in-sulation, double glazing and any energy efficient element. It then offers an ideal case study to ex-plore sustainable solutions which can be easily adopted from the construction industry and from the building owners. The primary objective of this research is twofold: first, to develop a comprehensive retrofit plan to transform the cultural hall into a net-zero energy building; and second, to explore how this transformation can give value back to the local community. After running two simulation scenarios and providing two energy performance certificates, one with at the existing state and one with the intended retrofit measures, it is clear that the building can be a net zero energy consump-tion building. Some interesting results derived, present also how this building can provide value back to the community i.e. through solar carports for EV charging.

Ensuring safe and continuous autonomous navigation in long-term mobile robot applications is still challenging. To ensure a reliable representation of the current environment without the need for periodic re-mapping, updating the map is recommended. However, in case of incorrect estimation of robot pose, updating the map can lead to errors that prevent the robot localisation and jeopardize map accuracy. In this paper, we propose a safe LIDAR-based occupancy grid map updating algorithm for dynamic environments taking into account the uncertainties in the estimation of the robot’s pose. The proposed approach allows robust long-term operations as it can recover the robot’s pose, even when it gets lost, to continue the map update process providing a coherent map. Moreover, the approach is robust also to temporary changes in the map due to the presence of dynamic obstacles such as humans and other robots. Results highlighting map quality, localisation performance, and pose recovery, both in simulation and experiments, are reported.

Since its original publication 1 in 1978, Lozi’s chaotic map has been thoroughly explored and continues to be. Hundreds of publications analyze its particular structure or apply its properties in many fields (electronic devices like memristor, A.I. with swarm intelligence, etc.). Several generalizations have been proposed, transforming the initial two-dimensional map into multidimensional one. However, they do not respect the original constraint that allows this map to be one of the few strictly hyperbolic: a constant Jacobian. In this paper we introduce a three-dimensional piece-wise linear extension respecting this constraint and we explore a special property never highlighted for chaotic mappings: the coexistence of thread-chaotic attractors (i.e., attractors which are formed by collection of lines) and sheet-chaotic attractors (i.e., attractors which are formed by collection of planes). This new 3-dimensional mapping can generate a large variety of chaotic and hyperchaotic attractors. We give five examples of such behavior in this article. In the first three examples, there is coexistence of thread and sheet-chaotic attractors. However, their shape are different and they are constituted by a different number of pieces. In the two last examples, the blow up of the attractors with respect to parameter a and b is highlighted.

Memristors were proposed in the early ’70s of the XXth century by Leon Chua as a new electrical element linking the charge and the flux. Since that first introduction, these devices have positioned themselves to be considered as possibly fundamental for the new generations of electronic devices. It has to be mentioned that actual memristors have only been recognized to exist as physical elements. In this paper, we apply a modeling framework to generate a model describing experimental measurements performed on a ReRAM. We show how to apply the Dynamic Route Map technique in the general case to obtain an approximation to the differential equation that determines the behaviour of the device.

The world tsunami hazard map is developed to understand the pattern of occurrence of tsunami across the globe and for using this database for preparing effective evacuation plan and rescue operations. It has been developed by using Web GIS tools. HTML, CSS, Java Script, JQuery, IIS and Maps API are utilized to develop hazard map. These data can be even used by government authorities as well as by other nodal agencies.

The paper presents an analysis of the latest developments in the field of stereo vision in the low-cost segment, both for prototypes and for industrial designs. We described the theory of stereo vision and presented information about cameras and data transfer protocols and their compatibility with various devices. The theory in the field of image processing for stereo vision processes is considered and the calibration process is described in detail. Ultimately, we presented the developed stereo vision system and provided the main points that need to be considered when developing such systems. The final, we presented software for adjusting stereo vision parameters in real-time in the python language in the Windows operating system.

In today's world it is very much important to maintain the security of information and its risks. The biometric-based techniques are very much useful in these problems. Among the several kinds of biometric-based technique, face detection is much complex and much more important. Due to the age and several other problems, a human face structure changes over time, again a human has lots of expressions. Sometimes due to the lighting condition or the variation of the angle of an input device, the pattern of a human face structure also changed. As a result, the face cannot be detected properly. In this paper, a method is proposed that can detect the human faces both automatically and manually very efficiently. In manual mode, a user can select the input faces referred by the system according to their choice. In automated mode, the system detected all possible face areas using the Kohonen Self-Organizing Feature Map technique. This method reduced the complex color image into a vector quantized image with desired colors. Then a color segmentation technique is used to detect the possible face skin areas from the vector quantized image. Then the Histogram Oriented Gradient technique used to detect the feature from the faces and K-Nearest Neighbour Classifier is used to compare both face images detected by the two modes. The automated method prosed better accuracy than the manual method.

Background: Human papillomavirus (HPV) infection plays a key role in the development of cervical cancer that ranks as the third most common gynecological cancer in China. We attempt to investigate the age and genotype-specific prevalence of HPV DNA in western Chinese females. Methods: A total of 301,880 woman were recruited from 4 different regions of western China. Routine cervical samples were collected and HPV screening was performed using 21 HPV Genotyping test (Hybribio). The overall prevalence, age-specific prevalence, and genotype distribution were analyzed. Results: The overall prevalence of HPV was 18.01%. The high-risk HPV infection rate was 79.14%, the low-risk HPV infection rate was 12.56%, and the mixed HPV infection rate was 8.30%. The most common 4 HR HPV subtypes were HPV-52, 16, 58 and 53, which accounted for 20.49 %, 19.93 %, 14.54 % and 10.01 %. In LR HPV genotype, HPV-6 ranked the highest (28.17 %), followed by HPV-81 (9.09 %), HPV-11 (3.78 %). HPV genotype subgroup analysis also showed that single-type infections had the highest prevalence rate (77.26%) among HPV positive individuals. Among muti-infection genotype, double infection was most common with frequencies of 76.04%. Conclusion: This large report shows that the overall prevalence of HPV was high in China, whose distribution exhibits different patterns across different particular age and regions. Viral genotypes HPV53, 6 were are frequently detected in this population, which is worth of significant clinical attention.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

Efficient fixed crane position analysis is critical in precast buildings construction to maximize lifting efficiency for precast elements. The primary objective is to minimize the travel distances of fixed cranes, thereby enhancing operational efficiency and cost control. This involves strategically reducing the distances between the transport truck parking, where elements are stored, the fixed crane, and the construction installation point. Despite its significance, existing studies often overlook the dynamic movement efficiency of transport trucks, particularly when dealing with multiple transport trucks and various models of fixed cranes, rendering the opti-mization of this scenario a challenging NP-hard problem susceptible to combinatorial explosion. This study presents a novel mathematical model leveraging the Genetic Algorithm (GA). The model aims to solve optimal model and position of fixed cranes, along with identifying ideal positions for transport truck parking. The study's methodology is validated and demonstrated through a project case study. Comparative analyses between the proposed model and the original planning underscore a noteworthy 6% reduction in both duration and costs when lifting elements directly from transport trucks, as opposed to establishing an on-site stock yard. Furthermore, the developed GA exhibits a substantial improvement in final solutions, achieving a remarkable 30% reduction in both operational duration and costs. This research contributes valuable insights into fixed crane position analysis of precast building construction, providing foundation for enhanced operational efficiency and cost-effectiveness in the industry.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Packaged water consumption has grown rapidly in urban areas of many low and middle income countries, but particularly in Ghana. However, the sources of water used by this growing packaged water industry and its implications for water resource management and transport-related environmental impacts have not been described. This study aimed to assess the spatial distribution of regulated packaged water production in Ghana, both in relation to demand and for natural mineral water, to hydrogeological characteristics. 764 addresses for premises licenced to produce packaged water from 2009-2015 were mapped and compared to regional sachet water consumption and beverage import/export data examined. We find evidence to suggest packaged water is transported shorter distances in Ghana than in developed countries. For natural mineral waters, producers should be able to address the most widespread water quality hazards (including high salinity, iron and nitrates) in aquifers used for production through reverse osmosis treatment. The study suggests there is scope to integrate beverage product and groundwater regulatory databases to support groundwater management.

In the last two centuries, land use change (LUC) has been the most important direct changes driver for terrestrial ecosystems. To contrast the consequent ecosystems degradation, forward-looking spatial policies and target landscape and land-use planning processes, promoting a sustainable land use change, are needed. The present paper proposes a framework of action including different landscape planning and ecological approaches: from the spatial modelling to recognize the LUC and build different scenarios, to the ecosystem services (ESs) assessment to evaluate the possible environmental impacts. Three different scenarios were built: Trend, No-Tillage and Energy crops. The Sediment Delivery Ratio and Carbon Storage and Sequestration ESs were assessed and compared for each scenario. The aim of the paper is to support decision-makers and local communities into the landscape planning process. Results show that a regional development in line with past trend could lead to further land degradation. Instead, the two scenarios proposed in compliance with EU policies, could bring benefits only if related to moderate LUCs and respecting the naturally grass-vegetated land. From the local to global scale, a guided and shared LUC management allows implementing sustainable development, basing on a deep knowledge of physical-environmental but also social and economic issues.

Digital twins are gaining in popularity for simulating complex natural and urban environments. In this context, accurate segmentation of objects within 3D urban environments is of crucial importance. The aim of this project is to develop a methodology for extracting buildings from textured 3D meshes. To this end, PicassoNet-II, a semantic segmentation architecture is employed. The methodology also incorporates Markov field-based contextual analysis to assess post-segmentation features. In addition, building instantiation is performed using cluster analysis algorithms. Training this model to fit various datasets requires a large amount of annotated data, both from Quebec City, Canada, and from simulated data. Experimental results show that the use of simulated data improves segmentation accuracy, and the DBScan algorithm proves effective in extracting isolated buildings. This project paves the way for improved applications in 3D urban modeling, offering opportunities in fields ranging from urban planning to resource management. The positive results with simulated data reinforce the impact of this research on improving digital models of our ever-changing urban environments.

This paper provides an open dataset of measured energy use, solar energy production, and building air leakage data from a 328 m² (3,531 ft²) all-electric, zero energy commercial building in Virginia, USA. Over two years of energy use data were collected at 1-hour intervals using circuit-level energy monitors. Over six years of solar energy production data were measured at 1-hour intervals by 56 microinverters. The building air leakage data was measured post-construction per ASTM-E779 Standard Test Method for Determining Air Leakage Rate by Fan Pressurization and the United States Army Corps (USACE) Building Enclosure Testing procedure; both pressurization and depressurization results are provided. The architectural and engineering (AE) documents are provided to aid researchers and practitioners in reliable modelling of building performance. The paper describes the data collection methods, cleaning, and convergence with weather data. This dataset can be employed to predict, benchmark, and calibrate operational outcomes in zero energy commercial buildings.

The laser differential equations are used to transform them into identical coupled maps. Valuable results are deduced during analytical and numerical studies on cavity loss. Phase and spatiotemporal synchronized attractors are observed via quasi-chaos under a certain range of controlling parameters, and symmetry breaking of chaotic attractors due to collision with their basin boundaries, and transpire differently from the previous attractors. During the numerical simulation, it is found that the sequence of repeated strange attractors if the coupling strength further increases, which are orthogonal mirror images (the dynamics of the system is the same at different values of controlling parameters). Moreover, it can help us to predict future problems and their solutions based on current issues, if we develop this model in more general.

A number of studies have been conducted to improve the accessibility of images using touchscreen devices for screen reader users. In this study, we conducted a systematic review of 33 papers to get a holistic understanding of existing approaches and to suggest a research road map given identified gaps. As a result, we identified types of images, visual information, input device and feedback modalities that were studied for improving image accessibility using touchscreen devices. Findings also revealed that little has studied how to automate the generation of image-related information, and that screen reader users play important roles during the evaluation but the design process. Then we introduce two of our recent studies on the accessibility of artwork and comics, AccessArt and AccessComics respectively. Based on the identified key challenges, we suggest a research agenda for improving image accessibility for screen reader users.

A finite-type immersion or smooth map is a nice tool to classify submanifolds of Euclidean space, which comes from eigenvalue problem of immersion. The notion of generalized 1-type is a natural generalization of those of 1-type in the usual sense and pointwise 1-type. We classify ruled surfaces with generalized 1-type Gauss map as part of a plane, a circular cylinder, a cylinder over a base curve of an infinite type, a helicoid, a right cone and a conical surface of $G$-type.

Despite increased protection globally, climate change and other anthropogenic factors have caused a significant decline in seagrass cover. Identifying the specific causes of this decline is paramount if they are to be addressed. Therefore, we identified the causes of long-term change in seagrass/submerged aquatic vegetation (SAV) percentage cover and extent in the Bluefields Bay Special Fish Conservation Area (BBSFCA), a marine protected area on Jamaica’s southern coast. We used two random forest regression (RFr) models that included 2013 hydroacoustic survey SAV percentage cover data (dependent variable), and auxiliary data, reflectance data from level 2 processed 2013 Landsat 7 and 8 images and image band texture statistics maps (mean and variance) as predictors to generate 24 SAV percentage cover maps for the period 1984 – 2021 (37 years) using data from Landsat 4-5, 7 and 8 images., from which benthic features maps (SAV present, absent and coral reef) were created. Rainfall and map data were used to determine if SAV extent/area (km2) and average percentage cover and annual rainfall changed significantly over time and to evaluate the influence of rainfall. Rainfall impact on the overall spatial patterns of SAV loss, gain, and percentage cover change was assessed using a pixel-based regression. Finally, the most important spatial pattern predictors (two rainfall proxies (distance and direction from river mouth), benthic topography, depth, and hurricane exposure (a measure of hurricane disturbance)) of SAV loss, gain, and percentage cover change during 23 successive 1-to-4-year periods were identified using spatial Bayesian INLA generalized linear mixed models. SAV area/extent was largely stable with > 70% mean percentage cover for multiple years. However, Hurricane Ivan (in 2004) caused a significant decline in SAV area/extent (by 1.62 km2, or a 13%) during 2002 – 2006 and a second hurricane (Dean) in 2007 delayed recovery until 2015. Additionally, rainfall declined significantly by >1000 mm since 1901, and mean monthly rainfall positively influenced SAV percentage cover change. The pixel-based regression highlighted areas where mean monthly rainfall had a positive overall effect on SAV cover percentage change (across the entire bay) and gain (closer to the mouth of a river). The most frequently selected important spatial pattern predictors were the two rainfall proxies (areas closer to the river mouth were more likely to experience SAV loss and gain) and depth, with shallow areas generally having a higher probability of SAV loss and gain. Three hurricanes had significant but different impacts depending on their distance from the southern coastline. Hurricane Gilbert, which made landfall in 1988, resulted in higher SAV percentage cover loss in 1987 - 1988. Benthic locations with a northwestern/northern facing aspect (the predominant direction of Ivan’s leading edge wind bands) experienced higher SAV losses during 2002 – 2006. Although some locations impacted by Ivan and not by Dean recovered during 2006 – 2008, exposure to Ivan explained percentage cover loss during 2006 – 2008 and average exposure to (the cumulative impact of) Ivan and Dean (both with tracks close to the southern coastline) explained SAV loss during 2013 – 2015. Therefore, despite historic lows in annual rainfall, overall, higher rainfall was beneficial, multiple hurricanes impacted the site, and despite two hurricanes in three years SAV recovered within a decade. Hurricanes and a further reduction in rainfall may pose a serious threat to SAV persistence in the future.

Mercury has a strong environmental impact since both its organic and inorganic forms are toxic and it represents a pollutant of global concern. Liquid Hg is highly volatile and it can be released during natural and anthropogenic processes in the hydrosphere, biosphere and atmosphere. In this study the distribution of Gaseous Elemental Mercury (GEM) and the total and leached mercury concentrations on paints, plasters, roof tiles, concretes, metals, dust and wood structures were determined in the main buildings and structures of the former Hg-mining area of Abbadia San Salvatore (Siena, Central Italy). The mining complex (divided into 7 units) covers a surface of about 65 ha and contains mining structures and managers and workers buildings. In this work, nine surveys of GEM measurements were carried out from July 2011 to August 2015 for the buildings and structures located in the units 2, 3 and 6. Moreover, detailed measurements were performed in February, April, July, September and December 2016 in the edifices and mining structures of Unit 6. GEM concentrations showed a strong variability in terms of space and time mostly depending on the distance from the building hosting driers, furnaces and condensers and ambient temperature, respectively. In the Unit 2 surveys carried out in the hotter period (from June to September) showed GEM concentrations up to 27,500 ng m⁻³, while in the Unit 6 they were on average much higher and occasionally they saturated the GEM measurement device (>50,000 ng m⁻³). Concentrations of total (in mg kg⁻¹) and leached (in μg L⁻¹) mercury measured in different building materials (up to 46,580 mg kg⁻¹ and 4,470 mg L⁻¹ for total and leached mercury, respectively) showed for the same type of material highly variable values in dependence on the edifice or mining structure from which they were collected. The results obtained in this study are of relevant interest for the operational cleanings to be carried out during the reclamation activities.

The objective was to conduct a scoping review and produce a publicly available database characterizing the design and reporting elements of the literature on dietary added sugars and select health outcomes. Relevant studies published from 1990 – 2021 were identified to create a database containing information on study and population characteristics, reported added sugars source and concentrations, diet energy balance, total energy intake, and outcome measures related to body composition, obesity, cardiovascular disease, and diabetes mellitus. There were 245 publications identified, 22% of which describe interventions and 78% describe observational studies. Publications pertaining to added sugars have risen dramatically since 2010, led by studies primarily assessing body composition (36%) or cardiovascular health (32%), including adults (65%), measuring liquid-only sources of added sugars (56%). Over 65% of studies reported total energy intake, 61% controlled for total energy intake in the design and analysis, and fewer than 5% of studies reported the energy balance of subjects. There has been a significant increase in research on added sugars since 2010, with substantial heterogeneity across all facets of methodology – study designs, exposures and outcomes of interest, terminology, and reporting of dietary intake data – thus limiting the ability to synthesize evidence in this scope of literature. This evidence map highlights gaps and important areas for improvement to strengthen the state of research to better inform future policies and dietary recommendations on added sugars.

In present paper, spatial Minkowski Pythagorean Hodograph (MPH) curves are characterized with Rational Rotation Minimizing Frames (RRMFs). We define Euler-Rodrigues Frame (ERF) for MPH curves and by means of this concept, we reach the definition of MPH curves of type (n, m). Expressing the conditions provided by these curves in the form of Minkowski-Hopf map that we define, it is aimed to establish a connection with the Lorentz force which occurs during the process of Computer Numerical Control (CNC) type sinker Electronic Discharge Machines (EDMs). This approach is reinforced by split quaternion polynomials. Finally, we give conditons satisfied by MPH curves of low degree to be type (n, m) and construct illustrative examples.

The flow behavior of Fe-6.5wt.%Si alloys during hot compression was investigated at temperatures 650–950 °C and strain rates 0.01–10 s^-1. The results showed that the flow stress depended distinctly on the deformation temperatures and strain rates. The flow stress and work hardening rate increased with the decrease of temperature and the increase of strain rate. The activation energy under all the deformation conditions was calculated to be 410 kJ/mol. The constitutive equation with hyperbolic sine function and Zener–Hollomon parameter was developed. The peak stress, critical stress, and steady-state stress could be represented as σ=A+Bln(Z/A). Dynamic recrystallization occurred under the deformation conditions where the values of Z were lower than 10²⁰. Processing maps were established to optimize the processing parameters. The power dissipation efficiency decreased in the high temperature and low strain rate region, increased in the high temperature and high strain rate region, and remained unchanged in other regions with the increase of true strain. Furthermore, the unstable area expanded. The true strain of 0.7 was the optimum reduction according to the processing map. Based on the analysis of surface quality, microstructures, and ordered structures, the optimized processing parameters for the Fe-6.5wt.%Si alloys were the temperature and strain rate of higher than 900 °C and 0.01–10 s^-1, respectively, or 800–900 °C and lower than 0.4 s^-1, respectively.

The Earth's fresh water resources predominantly is groundwater that is pumped out due to rapid urbanization and aggravated by climate change. Groundwater modeling is a crucial tool for understanding aquifer systems, employing 1D, 2D, and 3D numerical models with distinct applications. One-dimensional models focus on vertical dynamics, examining aquifer properties and simulating vertical contaminant transport. Two-dimensional models extend to regional scales, considering horizontal variations and assessing groundwater-surface water interactions, making them valuable for watershed-scale studies. Three-dimensional models provide a comprehensive representation of hydrogeological systems, capturing intricate flow patterns and aiding site-specific assessments. Comparative analysis reveals model strengths and limitations, emphasizing the importance of calibration for reliable results. Case studies showcase practical applications, such as 1D models in flooding analysis and 2D models for simulating debris flows. Three-dimensional modeling proves essential for understanding complex river-aquifer exchange fluxes. Future directions call for a global groundwater platform to address data variability and technical challenges. Despite substantial investments required, the anticipated returns in scientific advancements, societal benefits, and economic gains are expected to outweigh the initial costs. This review aims in highlighting the significance of advancing all three-dimension groundwater modeling for sustainable water resource management and environmental protection.

In this paper, the methodology using Insect Intelligent Building (I^2B) technology for establishing energy consumption monitoring system of public buildings is prevailed. The computing process node and distributed algorithm are utilized to implement the energy consumption collection and data transmission and data pre-processing. Taking a commercial building as a case study, CPNs are applied to set up the building energy consumption monitoring system, with the Spanning Tree Algorithm for generating network topology，and BPNN method for solving abnormal data and recovering missing data. The research results demonstrate the proposed method can effectively improve the performance of plug-and-play and self-identified and self-configuration of energy consumption monitoring system.

A comprehensive evaluation system of rural building energy consumption from a innovative composite perspective is established, which is suitable for southwest China. the brainstorming method and Delphi method were used to establish the indicator system, the ANP method was applied to calculate the weights of the comprehensive evaluation model, the scoring criteria of all evaluation indexes are constructed based on fuzzy evaluation theory, the applicability of the model is verified by an example of the countryside around Chengdu. The results showed that the score of some factors is low, whole or part area, just like the percentage of clean energy use(C24), the thermal performance of external walls(E21), the implementation of energy-saving measures(S22), were key factors affecting the target level, which has greater potential for improvement. The distribution of comprehensive indicators and evaluation factors have certain spatial distribution characteristics, the overall spatial distribution shows the characterwastic of "high in the southeast and low in the northwest". The key factors and spatial distribution characteristics found can be used as an important basis for the improvement of green energy-saving promotion measures, energy-saving retrofit programmes were proposed in terms of additional solar room, energy-saving of external walls and air-conditioning temperature setting guidance.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

The application of machine learning techniques to satellite imagery has been the subject of interest in recent years. The increase in quality and quantity of images, made available by Earth observation programs, such as the Copernicus program, led to the generation of large amounts of data. Among the various applications of this data is the creation of land cover maps. The present work aimed to create machine learning models capable of accurately segment and classify satellite images, to automatically generate a land cover map of the Portuguese territory. Several experiments were carried out with the spectral bands of the Sentinel-2 satellite, with vegetation indices, and with several sets of land cover classes. Three machine learning architectures were evaluated, which adopt two different techniques for image classification. One of the classification techniques follows an object-oriented approach, and in this case the architecture adopted in our models was a U-Net artificial neural network. The other classification technique is pixel-oriented, and the machine learning models tested were random forest and support vector machine. The overall accuracy of the results obtained ranged from 68.6% to 94.75%, depending strongly on the number of classes into which the land cover is classified. The result of 94.75% was obtained when classifying the land cover only into 5 classes. However, a very interesting accuracy of 92.37% was achieved by the model when trained to classify 8 classes. These results are superior to those reported in the related bibliography.

Symmetry in biological and physical systems is a product of self-organization driven by evolutionary processes, or mechanical systems under constraints. Symmetry-based feature extraction or representation by neural networks may unravel the most informative contents in large image databases. Despite significant achievements of artificial intelligence in recognition and classification of regular patterns, the problem of uncertainty remains a major challenge in ambiguous data. In this study, we present an artificial neural network that detects symmetry uncertainty states in human observers. To this end, we exploit a neural network metric in the output of a biologically inspired Self-Organizing Map, the Quantization Error (SOM-QE). Shape pairs with perfect geometric mirror symmetry but a non-homogenous appearance, caused by local variations in hue, saturation, or lightness within and/or across the shapes in a given pair produce, as shown here, longer choice RT for ‘yes’ responses relative to symmetry. These data are consistently mirrored by the variations in the SOM-QE from unsupervised neural network analysis of the same stimulus images. The neural network metric is thus capable of detecting and scaling human symmetry uncertainty in response to patterns. Such capacity is tightly linked to the metric’s proven selectivity to local contrast and color variations in large and highly complex image data.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

Ornamental kale (Brassica oleracea var. acephala) is an attractive ornamental plant with a range of leaf colors and shapes. Breeding new varieties of ornamental kale has proven challenging due to its lengthy breeding cycle and the limited availability of genetic markers. Microspore culture is an effective approach to generate new materials and genetic maps are a prerequisite for quantitative trait loci analysis, MAS, fine gene mapping, and genome sequence assembly. In this study, a F1DH ornamental kale population comprising 300 DH lines was constructed using microspore culture. A high-density genetic map was developed by conducting whole-genome sequencing on 150 individuals from the F1DH population. The genetic map contained 1,696 bin-markers with 982,642 single-nucleotide polymorphisms (SNPs) spanning a total distance of 775.81 cM on all nine chromosomes with an average distance between markers of 0.46 cM. The ornamental kale genetic map contained substantially more SNP markers compared with published genetic maps for other B. oleracea crops. The F1DH progenies provide an excellent resource for germplasm innovation and breeding new varieties of ornamental kale. The high-density genetic map provides crucial insights for gene mapping and unraveling the molecular mechanisms behind important agronomic traits in ornamental kale.

The complexity of the design in high-rise residential projects is a challenge for the construction industry in completing projects that fit the needs of users. Performance-Based Building Design (PBBD) appears as a design concept that can describe these needs into performance requirements. In this case designing a building can be considered as an iterative process of exploration, where desired functional properties can be created, the shapes are suggested, and evaluation processes is used, so as to bring together the shapes and functions of the building. This concept is a container for designers to produce high-performance buildings. This study aimed to identify the performance-based building design factors applied by architect designers and engineers in high-rise residential building in Surabaya. As part of this study, primary data was collected based on surveys conducted through observation and questionnaire distributed to designers who had or were involved in the high-rise residential design process in Surabaya. A total of sixty-eight respondents were included in this study. Descriptive analysis through a mean and standard deviation scatter plot was used to rank the application of PBBD. Meanwhile, factor analysis was used in the analysis of PBBD application factors. From the results of the analysis, four factors were obtained for the application of PBBD in high-rise residential buildings in Surabaya, namely; the interests of occupants, the sustainability of building operations, the design collaboration process, and the risk of loss. Future research is the influence relationships and measure the success model of PBBD at a higher level into BIM (Building Information Modeling) interoperability.

Due to its time effective, joint friendly and highly customizable character whole-body-electromyostimulation (WB-EMS) is regarded as a feasible solution for a large variety of training issues particularly in the area of non-athletic application. To identify gaps in research and summarize prevalent evidence we conducted an evidence map on outcomes addressed by WB-EMS trials in middle-aged to older, non-athletic adults. Based on a comprehensive systematic search in five databases and two study registers according to PRISMA, 54 projects published in 80 articles were included. More than 90% of the studies reported outcomes related to the physical fitness or function domain. Body composition parameters were addressed by two thirds of the projects. Health-related outcomes addressed by WB-EMS included cancer/neoplasm (n=7), endocrine regulation (n=8), glucose metabolism (15), nervous system diseases (n=2), cardiovascular system diseases (n=22), non-specific chronic low back pain (n=4), osteopenia (n=5) and diseases of the renal system (n=12). Outcomes related to inflammation were addressed 18 times. Of importance, no studies reported clinically relevant adverse effects related to the WB-EMS intervention. In summary, while considerable evidence on outcomes related to fitness/function and body composition is prevalent, evidence gaps of WB-EMS research were particular evident for diseases of the nervous and cerebrovascular system.

Insulation systems for the floor, roof and external walls play a prominent role in providing a thermal barrier for the building envelope. Design decisions made for the insulation material type and thickness can alleviate potential impacts on the embodied energy and improve the building thermal performance. This design problem is often addressed using a BIM-integrated optimisation approach. However, one major weakness lies in the current studies is that BIM is merely used as the source for design parameters input. This study proposes a BIM-based envelope insulation optimisation design framework using a common software Revit to find the trade-off between the total embodied energy of the insulation system and the thermal performance of the envelope by considering the material type and thickness. In addition, the framework also permits data visualisation in a BIM environment, and subsequent material library mapping together with instantiating the optimal insulation designs. The framework is tested on a case study based in Sydney, Australia. By analysing sample designs from the Pareto front, it is found that slight improvement in the thermal performance (1.3399 to 1.2112 GJ/m2) would cause the embodied energy to increase by more than 50 times.

There is a need to develop enriched milk drinks with healthy and natural additives. A consumer test was conducted to compare milk (cow and camel) flavored with date syrup (Khlass and Sukkary varieties) at different percentage. The objective of the present work was to study consumers liking patterns for flavored milk drinks from dates syrup (from Khlass and Sukkary dates), at different percentages, added to milk (cow and camel) utilizing preference mapping analysis. A total of sixteen trained panelists took part in the test. The obtained data were used to develop an internal preference map for these samples. Principal component analysis (PCA) and Agglomerative hierarchical clustering (AHC) algorithms were used to construct the preference map. The first component signifies overall acceptance of taste and color, while the second focuses on texture and flavor. Consumers were grouped into five clusters based on preferences. Cluster two favored both components positively, while cluster four leaned negatively on both. A factorial ANOVA was performed and the results showed a significant effect of the main factors as well as the interactions. Panelists preferred cow's milk over Camel’s milk in all aspects. For taste, cow’s milk with 20% Khlass syrup or 10% Sukkary syrup was favored, while in flavor, it was cow’s milk with 5% Khlass syrup and Camel’s milk with 10% Sukkary syrup. Texture-wise, Camel’s milk with 5% Khlass syrup and 15% Sukkary syrup, along with cow’s milk with 10% Khlass syrup, received top marks. In color evaluation, cow’s milk with 15% Sukkary syrup was the preferred choice. Finally, for overall color score, cow’s milk with 10% Sukkary syrup led, followed by cow’s milk with 5% Sukkary syrup. This research suggests that dairy companies may have more impact if they use date syrup as a natural and healthy flavor. The preference map includes two main dimensions; the first represents overall acceptance, taste, and color while the second is related to flavor and texture attributes. The preference map can be used in product optimization and development.

The demand for efficient processes through a comprehensive understanding and optimization of welding conditions continues to grow in the manufacturing industry. This study involves heat-resistant 2.25 Cr-1 Mo V-groove steel welding using the square-waveform alternating cur-rent. Experiments were conducted to build the relationship between input variables—such as current, frequency, electrode negativity ratio, and welding speed—and process performance, such as penetration, bay area, deposition rate, melting efficiency, percentage dilution, flux–wire ratio, and heat input. The process was analyzed in light of the defect-free high-deposition weld groove weld, the sensitivity to process parameters, and the optimization and development of the process map. The study proposes an innovative approach to reducing the cost and time of optimizing the one-pass-each-layer V-groove welding process using bead-on-plate welds. Square waveform welding creates a metallurgical notch in the form of a bay at the fusion boundary that can be minimized by selecting appropriate welding conditions. The square waveform submerged arc welding is more sensitive towards changes in current and welding speed than the frequency and electrode negativity ratio; however, the electrode negativity ratio and frequency are minor but helpful parameters to achieve optimal results. The proximity of the planned and experimental results to within 3% confirms the validity of the proposed approach. The investigation shows that 90% of the maximum deposition rate is possible for one-pass-each-layer V-groove welds within heat input and weld width constraints.

The research on the distribution of rural buildings is one of the fundamental works of urban-rural development in Vietnam. Adopting Mask R-CNN deep learning framework and collecting sub-meter remote sensing images, this research used a remote sensing interpretation model of rural buildings trained based on East Asian characteristics of rural buildings and successfully recognized about 2.87 million rural buildings in 34 Vietnamese provincial administrative districts with a total area of rural buildings of 2,492 million square meters. The reliability of the identification results was verified by manual detection and quantitative statistics, and a multi-scale database of rural buildings in Vietnam based on individual rural buildings was created. Based on the database, this paper analyzes the distribution characteristics of rural buildings and summarizes characteristics of rural buildings distribution at the country, regional, and provincial scales. The identification results lay the foundation for the next study of urban-rural relations in Southeast Asia and the construction of a basic database on villages.

Published data or available literature on sustainable building plan-design, construction, performance, and renovation criteria have covered some stages or some parts of each stage. These data usually have been published partially in many different papers―there have not been any papers that published these data together. Hence, this paper aims to collectively review these data and publish them together. The collection and review of these data were carried out by our twenty-five team members who specialized in sustainable urban, architectural, and civil engineering and construction management. The gathered and reviewed outputs were combined and validated based on a general group consensus. This consensus decision-making proceeded through two major group meetings with several follow-up meetings. The first major meeting was to combine and improve the gathered reviewed sustainable building criteria for Cambodia. The second major meeting was to validate the improved reviewed sustainable building criteria for Cambodia. The several follow-up meetings were to discuss the relevance and importance of the validated data “criteria and their classifications and descriptions” in all stages and more focused on their importance and applicability to Cambodia. The collective reviewed data in this paper would be useful to researchers in the fields. They could also be useful collective knowledge and information for policymakers from governmental agencies and development partners, particularly for sustainable building and construction companies.

Daniel Yergin’s “The New Map: Energy, Climate, and the Clash of Nations” is a remarkable and groundbreaking work that addresses the ever-changing global energy landscape and its profound geopolitical implications. In this modest book review, we aim to offer a fresh perspective by re-examining the core issues from the standpoint of political geography. The aim of this article is twofold: to enrich the existing literature on political geography and to provide valuable insights to students of geography to broaden their knowledge in this field.

This paper offers a novel geometric and visual approach to the renowned Four Color Map Theorem and K5 non-planarity problem while unveiling their profound connection to the "kissing number" problem in 2D. We represent planar graphs through circles and tangents, simplifying complex structures and shedding light on these classic problems. Our proofs by contradiction, rooted in the kissing number concept, reveal that both the Four Color Map Theorem and K5 non-planarity are fundamentally linked, as they pivot around the concept of coloring. This study bridges the realms of geometry and graph theory, providing fresh insights and emphasizing the significance of the kissing number problem in various fields.

Building deep learning models proposed by third parties can become a simple task when specialized libraries are used. However, a great deal of mystery still surrounds the design of new models or the modification of existing ones. These tasks require in-depth knowledge of the different components or building blocks as well as their dimensions. This information is limited and broken up in different literature. In this article, we collect and explain in-depth the building blocks to design deep learning models, starting from the artificial neuron to the concepts involved in building deep neural networks. Furthermore, the implementation of each building block is exemplified using the Keras library.

Considering the increasing rate of energy consumption and its environmental detrimental effects, as well as considering the use of non-renewable energy sources such as fossil fuels, energy management issues have become more important. Given the 40% share of the building industry's total energy consumption, as well as the 80% share of energy consumed during the operation period, attention to the areas of energy management and optimization during the operation period of the buildings can have a major impact on buildings’ energy performance. In this research, through identifying building energy management tools and studying previous studies and assessing the effects of building energy management systems, the economic and environmental impacts of using building energy management systems on the annual energy consumption in an office building in Tehran as a case study has been investigated. The results indicate a 32 percent reduction in energy consumption and a significant reduction in the release of the environmental pollutants in smart mode compared to the base mode. Moreover, considering the social costs associated with the emitted pollutants as well as the return period, it has been attempted to identify the factors contributing to the economic justification of using smart heating and cooling systems. According to the results, the use of smart energy management systems can be considered as an effective step in optimizing and managing energy consumption in the construction sector.

Hashimoto’s thyroiditis (HT) is a common autoimmune disease, with its prevalence rapidly increasing. Both genetic and environmental risk factors contribute to the development of HT. Recently, viral infection has been suggested to act as a trigger of HT by eliciting the host immune response and subsequent autoreactivity. We analyzed features of HT through bioinformatics analysis so as to identify markers of HT development. We accessed public microarray data of HT patients from the Gene Expression Omnibus (GEO) and obtained differentially expressed genes (DEGs) under HT. Gene Ontology (GO) and KEGG pathway enrichment analyses were performed for functional clustering of our protein-protein interaction (PPI) network. Utilizing ranked gene lists, we performed Gene Set Enrichment Analysis (GSEA) using the clusterprofiler R package. By comparing the expression signatures of the huge perturbation database with the queried rank-ordered gene list, connectivity map (CMap) analysis was performed to screen potential therapeutic targets and agents. The gene expression profile of the HT group was in line with general characteristics of HT. Biological processes related to the immune response and viral infection pathways were obtained for the upregulated DEGs. GSEA results revealed activation of autoimmune disease-related pathways and several viral infection pathways. Autoimmune disease and viral infection pathways were highly interconnected by common genes, while the HLA genes which are shared by both were significantly upregulated. CMap analysis suggested that perturbagens, including SRRM1, NLK, and CCDC92, have the potential to reverse the HT expression profile. Several lines of evidence suggested that viral infection and the host immune response are activated during HT. Viral infection is suspected to act as a key trigger of HT by causing autoimmunity. SRRM1, an alternative splicing factor, which responds to viral activity, might serve as potential marker of HT.

A surprising insight from the advent of genomic sequencing was that many genes are deeply conserved during evolution. With a particular focus on genes that interact with light in animals, I explore the metaphor of genetic toolkits, which can be operationalized as lists of genes involved in a trait of interest. A fascinating observation is that genes of a toolkit are often used again and again during convergent evolution, sometimes across vast phylogenetic distances. Such a pattern in the evolution of toolkits requires three different stages: origin, maintenance, and redeployment of the genes. The functional origins of toolkit genes might often be rooted in interactions with external environments. The origins of light interacting genes in particular may be tied to ancient responses to photo-oxidative stress, inspiring questions about the extent to which the evolution of other toolkits were also impacted by stress. Maintenance of genetic toolkits over long evolutionary timescales requires gene multifunctionality to prevent gene loss when a trait of interest is absent. Finally, the deployment of toolkit genes in convergently evolved traits like eyes sometimes involves the repeated use of similar, ancient genes but other times involves different genes specific to each convergent origin. How often a particular gene family is used time and again for the same function may depend on how many possible biological solutions are available. When few solutions exist and are maintained, evolution is constrained to use the same genes over and over. However, when many different solutions are possible, the innovative possibilities of evolution are often on display. Therefore, a focus on genetic toolkits highlights the combination of legacy plus innovation that drives the evolution of biological diversity.

Within microeukaryotes, genetic and functional variation sometimes accumulate more quickly than morphological differences. To understand the evolutionary history and ecology of such lineages, it is key to examine diversity at multiple levels of organization. In the dinoflagellate family Symbiodiniaceae, which can form endosymbioses with cnidarians (e.g., corals, octocorals, sea anemones, jellies), other marine invertebrates (e.g., sponges, molluscs, flatworms), and protists (e.g., foraminifera), molecular data have been used extensively over the past three decades to describe phenotypes and to make evolutionary and ecological inferences. Despite advances in Symbiodiniaceae genomics, a lack of consensus among researchers with respect to interpreting genetic data has slowed progress in the field and acted as a barrier to reconciling observations. Here, we identify key challenges regarding the assessment and interpretation of Symbiodiniaceae genetic diversity across three levels: species, populations, and communities. We summarize areas of agreement and highlight techniques and approaches that are broadly accepted. In areas where debate remains, we identify unresolved issues and discuss technologies and approaches that can help to fill knowledge gaps related to genetic and phenotypic diversity. We also discuss ways to stimulate progress, in particular by fostering a more inclusive and collaborative research community. We hope that this perspective will inspire and accelerate coral reef science by serving as a resource to those designing experiments, publishing research, and applying for funding related to Symbiodiniaceae and their symbiotic partnerships.

This paper investigated building data from multispectral and single-photon Lidar systems. The multispectral datasets from the individual channels and fused channels were explored. The multispectral and single-photon Lidar data were compared across multiple aspects: the data acquisition geometry, number of echoes, intensity, density, resolution, data defects, noise level, and the absolute and relative accuracy. In addition, we explored the performance of the multispectral and single-photon data for roof plane detection for eight complex/stylish buildings to investigate the suitability of these data for 3D building reconstruction. The building data from the single-photon and multispectral Lidar systems were evaluated with respect to the reference building vector data with an accuracy of better than 5 cm. The advantages and disadvantages of both technologies and their applications in the urban building environment are discussed.

There has been a growing awareness of the need to implement environmentally friendly operations in the hotel industry, but most studies focus on guest behaviors. Only a few studies investigate employees’ willingness to comply with hotels’ green practices. This study seeks to further the investigation from the human resource perspective. Using alumni from a tourism and hospitality programs, this study collected 233 responses. The study hypothesizes that the employees’ green ability consisting of environmental awareness, environmental knowledge, and environmental skill creates a positive impact on hotels’ green ability. The results indicate that employees contribute approximately a fifth of hotels’ ability to implement greener practices.

Whole-body electromyostimulation (WB-EMS) can be considered as a time-efficient, joint-friendly and highly customizable training technology that attracts a wide range of users. The present evidence map aimed to provide an overview of different non-athletic cohorts addressed by WB-EMS research. Based on a comprehensive systematic search according to PRISMA, eighty-six eligible longitudinal trials were identified that correspond with our eligibility criteria. In summary, WB-EMS research sufficiently covers all adult age categories in males and females. Most cohorts addressed (58%) were predominately or exclusively overweight/obese and in about 60% of them, diseases or conditions were inclusion criteria for the trials. Cohorts specifically addressed by WB-EMS trials suffer from cancer/neoplasm (n=7), obesity (n=6), diabetes mellitus (n=5), the metabolic syndrome (n=2), nervous system diseases (n=2), chronic heart failure (n=4), stroke (n=1), peripheral arterial diseases (n=2), knee arthrosis (n=1), sarcopenia (n=3), chronic unspecific low back pain (n=4), and osteopenia (n=3). Chronic kidney disease was an eligibility criterion in five WB-EMS trials. Finally, three studies included only critically ill patients, two further studies considered frailty as an inclusion criterion. Of importance, no adverse effects of the WB-EMS intervention were reported. In summary, evidence gaps of WB-EMS research were particular evident for cohorts with diseases of the nervous and cerebrovascular system.

Despite several decades of research, the physics underlying translation – protein synthesis at the ribosome – remains poorly studied. For instance, the mechanism coordinating various events occurring in distant parts of the ribosome is unknown. Very recently, we have suggested that this allosteric mechanism could be based on the transport of electric charges (electron holes) along RNA molecules and localization of these charges in the functionally important areas; this assumption was justified using tRNA as an example. In this study, we turn to the ribosome and show computationally that holes can also efficiently migrate within the whole ribosomal small subunit (SSU). The potential sites of charge localization in SSU are revealed, and it is shown that most of them are located in the functionally important areas of the ribosome – intersubunit bridges, Fe4S4 cluster and the pivot linking the SSU head to the body. As a result, we suppose that hole localization within the SSU can affect intersubunit rotation (ratcheting) and SSU head swiveling, in agreement with the scenario of electronic coordination of ribosome operation. We anticipate that our findings will improve the understanding of the translation process and advance the molecular biology and medicine.

In mitosis, faithful chromosome segregation is orchestrated by the dynamic interactions between the spindle microtubules (MTs) emanating from the opposite poles and the kinetochores of chromosomes. However, the precise mechanism that coordinates the coupling of kinetochore components to dynamic MTs has been a long-standing question. Microtubule (MT) associated proteins (MAPs) regulate MT nucleation, dynamics, MT-mediated transport and MT cross-linking in cells. Especially during mitosis, MAPs play an essential role not only in determining the spindle length, position and orientation but also in facilitating robust kinetochore-microtubule (kMT) attachments by linking the kinetochores to spindle MTs efficiently. MT-stability imparted by the MAPs is critical to ensure accurate chromosome segregation. This review primarily focuses on the specific function of non-motor kinetochore MAPs, their recruitment to kinetochores and their MT-binding properties. We also attempt to synthesize and strengthen our understanding of how these MAPs work in coordination with the kinetochore-bound Ndc80 complex (the key component of the MT-binding interface in metaphase and anaphase) to establish stable kMT attachments and control accurate chromosome segregation during mitosis.

This paper investigates the impact of price and real exchange rate volatility on Foreign Direct Investment (FDI) inflows in a panel of 10 Latin American and Caribbean countries, observed between 1990 and 2012. Both price and exchange rate volatility series are estimated through the Generalized Autoregressive Conditional Heteroscedasticity model (GARCH). Our results, obtained employing the Fixed Effects estimator, confirm the theory of hysteresis and option value, in so far it is found a statistically significant negative effect of exchange rate volatility on FDI. Price volatility, instead, turns out to be positive but insignificant. Moreover, we show that human capital and trade openness are key for attracting foreign capital. From the policy perspective, our analysis suggests the importance of stabilization policies as well as the one of government credibility in promoting trade openness and human capital formation.

Chaotic theory is commonly being researched for application in image encryption scheme (IES). In this paper, a novel two-dimensional cross hyperchaotic Sine-modulation-Logistic map (2D-CHSLM) based on the famous Sine and Logistic maps. The hyperchaotic behaviors of 2D-CHSLM is testified with the help of their bifurcation diagrams, trajectory plots, Lyapunov exponents, sample entropy, C0 complexity, permutation entropy and 0-1 test. A new bit-level IES with traditional encryption structure is proposed utilizing 2D-CHSLM. The 2D-CHSLM-IES performs a 2D-CHSLM-based bit-level confusion using zig-zag transform and a 2D-CHSLM-based cross coupled diffusion operations for generating a highly secure cipher-image. Then the simulations and security analyses are further carried out with the help of key space, key sensitivity, histogram, correlation, information entropy, differential attack, noise and data loss attacks, prove that the security of the proposed 2D-CHSLM-IES

Image encryption is increasingly becoming an important area of research in information security and network communications, as digital images are widely used in various applications and are vulnerable to various types of attacks. In this research work, a color image cryptosystem that is based on a 3-layer permutation-substitution network (PSN) is proposed. For every layer, an encryption key and an S-box are generated and utilized. Those are based on a four-dimensional (4D) dynamical Chen system of a fractional-order, the Mersenne Twister, OpenSLL, Rule 30 Cellular Automata and Intel’s MKL. The sequential application of Shannon’s ideas of diffusion and confusion for 3 times guarantees a total distortion of any input plain image, resulting in a totally encrypted one. Apart from the excellent and comparable performance to counterpart algorithms from the literature, showcasing resistance to visual, statistical, entropy, differential, known plaintext and brute-force attacks, the proposed image cryptosystem provides an exceptionally superior performance in 2 aspects: a vast key space of 2^1658 and an average encryption rate of 3.34 Mbps. Furthermore, the proposed image cryptosystem is shown to successfully pass all the tests of the NIST SP 800 suite.

The diagnosis of Cardio-Vascular diseases (CVD) is highly dependent on analysis of ECG signals. ECG analysis can be helpful in estimating the underlying cause and condition of heart in cardiac abnormality. The effectiveness of ECG signal analysis in detection of CVDs is widely accepted by professional healthcare service provider. Many algorithms have been proposed but almost all of them have some kind of limitations, and these limitations largely influence the effectiveness of ECG analysis. The performed research work is dedicated for design of unique self-organizing maps (SOMs) based neural network for classification of arrhythmia according to a particular ECG signal, the generation of SOMs is based on the certain unique signatures of ECG signals and have potential to classify different cardiac conditions. For extraction of unique features from ECG signals, we have proposed to use Fast Discrete Stockwell Transform (FDST). Since the proposed technique is a result of combining two different techniques hence called as hybrid technology. The purpose of using FDST is to identify unique signatures of ECG signals in a more improved manner than existing one, the term improved is used because it has several advantages over existing techniques such as wavelet and Fourier Transform based methods. Results obtained from the implementation of the technique are capable in visualizing the ECG sinus rhythm and arrhythmia conditions in form of unique SOM for each associated arrhythmia condition. This unique SOM based classification makes them ideal for being used as a diagnostic tool. This ability of arrhythmia classification using FDST and SOMs makes the technique unique and useful providing valuable information about patient condition. Using proposed technology a portable diagnosis tool for monitoring of patient at their site may be facilitated later, that will improve the quality of life of the patient by diagnosing cardiac condition.

Building electric energy is characterized by a significant increase of its uses (e.g. vehicle charging), a rapidly declining cost of all related data collection and a proliferation of smart grid concepts, including diverse and flexible electricity pricing schemes. Not surprisingly, an increased number of approaches have been proposed for its modeling and forecasting. In this work, we place our emphasis on three forecasting related issues. First, on the forecasting explainability, i.e. the ability to understand and explain to the user what shapes the forecast. To this extent we rely on concepts and approaches that are inherently explainable, such as the evolutionary approach of genetic programming (GP) and its associated symbolic expressions, as well as the so-called SHAP (SHapley Additive eXplanations) values, which is a well established model agnostic approach for explainability, especially in terms of feature importance. Second, we investigate the impact of the training timeframe on the forecasting accuracy; this is driven by the realization that a fast training would allow for faster deployment of forecasting in real life solutions. And third, we explore the concept of counterfactual analysis on actionable features, i.e. features that the user can really act upon and which therefore present an inherent advantage when it comes to decision support. We have found that SHAP values can provide important insights into the model explainability. As for GP models, we have found comparable and in some cases superior accuracy when compared to its neural-network and time-series counterparts but a rather questionable potential to produce crisp and insightful symbolic expressions, allowing a better insight into the model performance. We have also found, and report here on an important potential especially for practical, decision support, solutions of counterfactuals built on actionable features and short training timeframes.

This short paper reveals a simple methodology to create local-correlation models suitable for the closed-form pricing of multi-asset financial derivatives. The multivariate models are built to ensure two conditions, first, marginals follow desirable processes, e.g. we choose the Geometric Brownian Motion (GBM), popular for stock prices. Second, the payoff of the derivative should follow a desired one dimensional process. These conditions lead to a specific choice of the dependence structure, in the form of a local-correlation model. Two popular multi-asset options are entertained, a spread option and a basket option.

The good management of the building maintenance should be based on the regular maintenance work. Repair works are often not carried out or there are shifts in time, which causes degradation of the building. The article presents a method of planning renovation works of a MUBAR (maintenance Management in an Un-renovated Building with Abandoning Renovation) based on the consequences in case of their lack. No renovation work on individual elements in a building can cause a threat to the stability of the building structure, risking the lives of users, continuing damage to the building by damaging further elements, or even a building disaster. The method can also be applied to historic buildings. Often, due to abandonment of repairs caused most often by lack of the owner, improper manager or irresponsible users, degradation of these objects occurs. The consequences of neglected renovation of buildings lead to irreversible processes of their destruction. The aim of the article is to present the developed method of planning renovation works based on the consequences of lack of renovation works.

In this research paper we describe the development phase of a low-cost LoRa IoT solution applied to a kindergarten school with three years results. A set of sensors solution was developed in a LoRa communication board, battery powered, providing a simplified setup process. These sensors were used in order to measure temperature, humidity, luminosity, air quality and presence. Also, energy monitor solutions were integrated. The acquired data is transmitted and analysed for knowledge extraction, identifying savings and other related KPIs. From data, automatic saving actions were performed towards heating and cooling systems, lighting and a set of if-then actions were developed for automatic cost-saving actions, based on infrared signals to heating/cooling systems using some procedure of external command devices. This approach avoids the usage of proprietary vendor solutions in a flexible approach that can easily be deployed to any building facility. This is an important achievement since most of the building consumption is based on heating and cooling systems. In a three years test of the solution, the total energy consumption savings surpassed 20%

The present article analyzes the integration of green building policy and practice with the largest low-income housing production program in the US and the innovativeness of its housing agencies. Drawing on policy innovation literature, panel data and regression analysis are employed to quantify associations between state-level characteristics and the adoption of green building criteria into the Low-Income Housing Tax Credit (LIHTC) program. Results show that, on average, housing agencies have increasingly adopted green building criteria, and most have identified co-benefits from energy-efficient buildings and smart growth. Despite overall progress, the rate of adoption of green building criteria has decreased, few states have comprehensive criteria, and many have dropped important criteria, such as on-site renewable energy generation. Results are consistent with hypotheses derived from the literature and suggest the integration of green building with LIHTC developments is significantly associated with government motivation, financial resources, and exogenous characteristics that affect the demand for green building. Future research should explore organization-level factors that affect environmental policy innovation. It is recommended that LIHTC housing agencies require compliance with green building rating systems and periodically reconfigure green building criteria based on planned evolutionary change, data-driven strategies, and life-cycle analyses towards zero net energy consumption.

Hybrid materials of conjugated polymer and titanium(IV) oxide have attracted considerable attention concerning potential benefits, including (i) efficient exploitation of visible light, (ii) high adsorption capacity for organic contaminants, (iii) effective charge carriers separation. The new class of the photocatalysts is promising for the removal of environmental pollutants in both aqueous and gaseous phases. For the first time, in this study, the PANI/TiO₂ hybrid composite was used for the degradation of phenol in water and toluene in the gas phase. Polyaniline-TiO₂ was prepared by in-situ polymerization of aniline on the TiO₂ surface. The obtained hybrid material was characterized by diffuse reflectance spectroscopy (DR/UV-Vis), X-ray diffraction (XRD), fast-Fourier transformation spectroscopy (FTIR), photoluminescence (PL) spectroscopy, microscopy analysis (SEM/TEM) and thermogravimetric analysis (TGA). An insight into the mechanism was shown based on the photodegradation analysis of charge carriers scavengers. Polyaniline is an efficient TiO2 photosensitizer for photodegradation in visible light (λ> 420 nm). The trapping experiments revealed that mainly h+ and ˙OH were reactive oxygen species responsible for phenol degradation. Furthermore, the PANI-TiO₂ hybrid nanocomposite was used in gypsum plaster to study the self-cleaning properties of the obtained building material. The effect of PANI-TiO₂ content on hydrophilic/hydrophobic properties and crystallographic structure of gypsum was studied. The obtained PANI-TiO₂ modified gypsum plaster had improved photocatalytic activity in the reaction of toluene degradation under Vis light.

This paper proposes a Mixed Integer Conic Programming (MICP) model for community microgrids considering the network operational constraints and building thermal dynamics. The proposed multi-objective optimization model optimizes not only the operating cost, including fuel cost, purchasing cost, battery degradation cost, voluntary load shedding cost and the cost associated with customer discomfort due to room temperature deviation from the set point, but also several performance indices, including voltage deviation, network power loss and power factor at the Point of Common Coupling (PCC). In particular, the detailed thermal dynamic model of buildings is integrated into the distribution optimal power flow (D-OPF) model for the optimal operation. The heating, ventilation and air-conditioning (HVAC) systems can be scheduled intelligently to reduce the electricity cost while maintaining the indoor temperature in the comfort range set by customers. Numerical simulation results show the effectiveness of the proposed model and significant savings in electricity cost with network operational constraints satisfied.

An extension of the models used to generate fractal traffic flows is presented by means of the formulation of a model that considers the use of one-dimensional chaotic maps. Based on the disaggregation of the temporal series generated by the model, a valid explanation of behavior of the values of Hurst exponent is proposed and the feasibility of their control from the parameters of the proposed model is shown.