This case report describes evidence of intratubular biomineralization in root canal filled with calcium enriched material after 8 years of clinical maintenance. The schematic findings of dentinal tubules were investigated with scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The root canal obturation material was closely adapted to root dentin surface, suggesting the possibility of chemical bonding between the two interfaces. SEM and EDS observation of dentinal tubules showed intratubular biomineralized crystal structures with Ca/P ratio in a range of 1.30–2.12, suggesting bioactive capacity of calcium enriched cement.

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (>0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

Today, enhancing food preservation and safety in the spirit of the bioeconomy suggests the use of biodegradable polymers such as poly-L-lactic acid (PLA) in food packaging and the replacement of chemical additives with natural antioxidant/antibacterial agents such as essential oils and their derivatives. Herein a novel carvacrol (CV) @ natural zeolite (NZ) nanohybrid was developed by employing a new vacuum adsorption desorption method which results in the adsorption of a high CV amount on NZ equal to 61.7 %wt. This CV@NZ nanohybrid was successfully dispersed in a PLA/triethyl citrate (TEC) matrix via a melt-extrusion process to obtain PLA/TEC/xCV@NZ nanocomposite films with 5, 10 and 15 CV@NZ %wt. content. PLA/TEC/xNZ films were also de-veloped for comparison. The overall study resulted in a biodegradable active film with the fol-lowing properties: 10%wt. CV@NZ content (PLA/TEC/10CV@NZ), self-healable properties, 22% higher tensile strength and 40% higher elongation at break, 45% higher water barrier and 40% higher oxygen barrier than pure PLA/TEC matrix. This film also provides high CV release content, high CV control release rate as well as significant antioxidant activity and antibacterial activity against the food pathogens Staphylococcus aureus and Salmonella enterica spp. enterica serovar Typhimurium. This film not only succeeds in extending the shelf-life of fresh pork minced, as shown by total variable count measurements in four days, but also prevents lipid oxidation of fresh minced pork and maintains the minced meat in higher nutritional conditions, as revealed by the heme iron content determination, and in a much better and acceptable sensory condition than the commercial packaging paper.

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

Shape memory alloys (SMA) are becoming a more important factor in actuation technology. Due to their unique features, they bring the potential to safe weight, installation space and reduce energy consumption. The system integration of the generally small diameter NiTi wires is an important cornerstone for the emerging technology. Crimping, a common method for the mechanical and electrical connection of SMA wires, has several drawbacks when it comes to miniaturization and high force outputs. For high force applications for example, multiple SMA wires in parallel are needed to keep actuation frequencies high, while scaling up the actuation force. To meet these challenges, the proposed study deals with the development of a resistance welding process for manufacturing NiTi wire bundles. The wires are welded to sheet metal substrate, resulting in promising functional properties and high joint strengths. The welding process benefits from low cost, easy to control parameters and good automation potential. A method for evaluating the resistance welding process parameters is presented. With these parameters in place, a manufacturing process for bundled wire actuators is discussed and implemented. The welded joints are examined by peel tests, microscopy, and fatigue experiments. The performance of the manufactured bundle actuators is demonstrated by comparison to a single wire with the same accumulated cross-sectional area.

This study explores the potential of titanium disulfide (TiS2) as an active material for aqueous calcium-ion batteries (CIBs). We investigate the electrochemical redox reactions of calcium ions within TiS2 and assess its suitability for use in aqueous CIBs. Additionally, we examine the im-pact of different electrolyte concentrations on TiS2 electrode reactions. Our findings reveal that TiS2 exhibits distinct charge-discharge behaviors in various aqueous calcium-ion electrolytes. Notably, at higher electrolyte concentrations, TiS2 effectively suppresses the hydrogen genera-tion reaction caused by water decomposition, demonstrating its potential as an active material for aqueous CIBs. In-situ X-ray diffraction analysis confirms the intercalation of Ca2+ ions be-tween TiS2 layers during charging. This confirmation is groundbreaking, as it represents the first experimental evidence of calcium ions being electrochemically inserted between TiS2 layers from aqueous solutions, signifying a previously unreported achievement and strongly suggesting TiS2's applicability in aqueous CIBs. X-ray photoelectron spectroscopy analysis further supports the formation of a solid electrolyte interphase (SEI) on the TiS2 electrode surface, contributing to the suppression of electrolyte decomposition reactions. Furthermore, we investigate the influ-ence of anions in the electrolyte on charge-discharge behavior. Our findings suggest that the choice of anion coordinated with Ca2+ ions affects SEI formation and cycling performance. Un-derstanding the role of anions in SEI formation is crucial for optimizing aqueous CIBs. In con-clusion, this research underscores TiS2's potential as an active material for aqueous calcium-ion batteries and emphasizes the importance of electrolyte composition in influencing SEI formation and battery performance. These findings contribute to the development of more sustainable and efficient energy storage technologies.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

Familial Alzheimer’s disease (FAD) can be caused by mutations in PSEN1 that encodes presenilin-1, a component of the gamma-secretase complex that cleaves amyloid precursor protein. Alterations in calcium (Ca2+) homeostasis and glutamate signaling are implicated in the pathogenesis of FAD, however it has been difficult to assess in humans whether or not these phenotypes are the result of amyloid or tau pathology. This study aimed to assess early calcium and glutamate phenotypes of FAD by measuring the Ca2+ response of induced pluripotent stem cell (iPSC)-derived neurons bearing PSEN1 mutations to glutamate and the ionotropic glutamate receptor agonists NMDA, AMPA and kainate compared to isogenic control and healthy lines. The data shows that in early neurons, even in the absence of amyloid and tau phenotypes, FAD neurons exhibit increased Ca2+ responses to glutamate and AMPA, but not NMDA or kainate. Together this suggests that PSEN1 mutations alter Ca2+ and glutamate signaling as an early phenotype of FAD.

Electronic waste generation has been following a continuously rising trend. With electronics containing a myriad of materials some of which are hazardous, toxic, extremely rare or precious combined with more stringent legislative laws which encourage the reuse and optimised recycling of the materials included in e-waste, the need for a holistic approach is inevitable. Such an approach should not only identify the materials found in the various types of e-waste and their respective quantities but also needs to highlight the possible handling techniques and their respective impacts and associated hazards whether to the environment or human health. Performing such a task manually would be exasperating and costly while requiring extensive resources which might not be met with a justifiable economic gain; thus, the use of the advancement in computational sustainability to draw a complete picture and aid in an informed decision-making process is crucial. The e-waste ontology developed in this paper is one way of addressing the problem since it covers the treatment domain, the hazard and the materials contained within the different types of e-waste. The ontology developed can be used directly from the protégé software or by embedding it into a developed Decision Support System.

To evaluate the used and End-of-Life tyre management chains, both direct observation and interviews with approximately 200 used-tyre dealers were conducted. The study revealed that while the used tyre business is well-organized, End-of-Life tyre treatment is nearly non-existent, often involving dumping, open burning for metal recovery, or use in meat processing, causing environmental and health risks. To address these challenges, an 8 t/hr capacity tyre recycling plant is planned, based on estimated tyre availability and development opportunities for sustainable recycling in Togo.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Milk serves as a crucial source of natural bioactive compounds essential for human nutrition and health. The gastrointestinal digestion of milk proteins releases various biologically active peptides that positively impact human health and enhance physiological performance. With the growing production of cheese, Greek yogurt, and other dairy products, the volume of unutilized acid whey is significantly increasing. Acid whey, containing almost all whey proteins and approximately one-quarter of casein, presents a valuable raw material for generating peptides with potential health benefits. These peptides exhibit properties such as antioxidant, antimicrobial, anti-inflammatory, anticarcinogenic, antihypertensive, antithrombotic, opioid, mineral-binding, and growth-stimulating activities, contributing to improved human immunity and the treatment of chronic diseases. Enzymatic hydrolysis of milk proteins has been developed as a method to produce these peptides, facilitating their use in food fortification. To incorporate whey into functional beverages, it undergoes fermentation by lactic acid bacteria with proteolytic activity. To specifically enrich these beverages with peptides exhibiting targeted bioactivities, it is essential to select lactic acid bacteria strains possessing the requisite protease profiles. Additionally, the sensory properties of the final product can be enhanced using starter cultures with diverse metabolic capabilities, even in the absence of added flavoring agents. Given the imperative to develop waste-free technologies and enhance the profitability of the dairy industry, there is a growing need to efficiently utilize and transform acid whey into a broad spectrum of valuable products and food additives. This approach is justified not only by the nutritional benefits of the bioactive components in whey but also by the commercial potential of safe and health-enhancing products.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Biosolids from stabilized sludge presents a high fertilization potential due to its rich content of nutrients and organic matter. Three formulas of organo-mineral fertilizers based on biosolids were manufactured having at least 2 % N, 2 % P2O5, and 2 % K2O and characterized by classical and advanced methods. The content of N and P in the final formula was measured using specific reactants combined with VIS-nearIR spectroscopy. Additionally, all three formulas were characterized by advanced 1H NMR relaxometry, double-quantum and FT-IR spectroscopy. Structural characterization was performed using SEM, EDX and X-ray diffraction. Four dynamical components were identified in the T2-distribution showing that the rigid component is into a percentage larger than 90 %. In order to evaluate the release properties of organo-mineral fertilizers dynamic measurements of electric conductivity and pH were performed, by placing 0.25 g of formulas (V1, V2 and V3) in 200 ml of distillate water. It was found that V3 present the smallest release velocity, but release the largest amount of fertilizers. Two release mechanisms were also observed.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

We aimed to evaluate the association between daily dietary calcium intake and the risk of cardiovascular disease (CVD) in postmenopausal women using data from the Korean National Health and Nutrition Examination Survey (KNHANES). This cross-sectional study included 12,348 women aged 45–70 years who had reached natural menopause. They were classified into three groups according to daily dietary calcium intake: < 400 mg, 400–800 mg, and >800 mg. The risks of CVD, stroke, angina, and myocardial infarction were assessed in each group. Further, we performed subgroup analysis according to the post-menopause duration (≤10 vs. >10 postmenopausal years). We performed logistic regression analysis with adjustment for age, menopausal age, income, urban area, education, insulin use, body mass index, hypertension, diabetes mellitus, dyslipidemia, high alcohol intake, smoking, exercise, oral contraceptive use, and hormonal therapy use. Calcium intake level was not significantly associated with the risk of CVD in the total population and the ≤10 postmenopausal years subgroup. However, in the >10 postmenopausal years subgroup, daily calcium intake >800 mg was associated with significantly decreased risks of all CVD (odds ratio [OR], 0.27; 95% confidence interval [CI], 0.11–0.64), stroke (OR, 0.06; 95% CI, 0.01–0.42), and myocardial infarction (OR, 0.27; 95% CI, 0.11–0.64). Our findings suggest that a dietary calcium intake of >800 mg/day decreases the risk of CVD events in women who have been menopausal for >10 years.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

There are various types of charged particles in the space environment, which can cause different types of radiation damage to materials and devices, leading to on-orbit failures and even accidents of spacecraft. Developing lightweight and efficient radiation shielding materials is an effective approach to improve the inherent protection of spacecraft. The protective performance of different materials against proton and electron spectra in the Earth’s radiation belts is evaluated by Geant4 simulation. Based on the simulation results, suitable hardening components are selected to design composite materials, and B4C/PEEK composites with different B4C content were successfully prepared. Experimental results demonstrate that the simulated and experimental results for the electron, proton and neutron shielding performance of B4C/PEEK composites are consistent. These composites exhibit excellent radiation shielding capabilities against electrons, protons and neutrons, and the radiation protection performance improves with increasing B4C content in the B4C/PEEK composite materials.

This paper describes a novel concept of producing energy efficient ”Maroon enriched natural gas “ and then Pink hydrogen” from any hydrocarbon base. The key idea is the extraction of hydrogen from water in addition to that from the hydrocarbon in an optimal fashion. This has the benefit of higher water vapor to CO2 exhaust ratio than conventional carbonaceous fuels when generating energy via combustion, a prudent step in achieving Netzero goals in a shorter time, and creating energy independence in most places.. The process of production makes concentrated CO₂ available for use and or sequestration. The process also maximizes use of renewable electricity in hydrogen generation, and maximizes use of existing infrastructure, with a minimum capital cost by energy recycle in the process. The process design applies sound thermodynamic principles which evolved during the nineteenth century, and mimics the geochemical processes going on in some of the natural 'colorless hydrogen'.

Since the mid-1990s probiotics have been proven to support the treatment of several gastrointestinal diseases. Additionally, probiotics have been taken as a common panacea for civilization diseases. To date, the only probiotic yeasts with evidence of health-promoting effects are Saccharomyces cerevisiae var. boulardii. The probiotic properties are strain-dependent, whereby it is crucial to develop methods to verify the probiotic-enriched food authentication including the growing number of dietary supplements with simplified commercialisation procedures. Due to the significant genetic similarity of S. cerevisiae var. boulardii to S. cerevisiae, qPCR-HRM analysis was tested, which has a very high sensitivity for polymorphism detection and enables simultaneous identification of the microorganism in the presence of the reference sample. The effectiveness of interspecies primer pairs and intragenus primer pairs designed to amplify heterogeneous regions was examined. HRM analysis using primers for 18SrRNA and ITS allowed for identification of S. cerevisiae var. boulardii at the species level. S. cerevisiae var. boulardii was efficiently identified at the variety level with amplification of HO and RPB2 in the single- and multi-component DNA extracts. The RPB2 amplicon showed the highest intraspecies differentiation power. The predominance of S. cerevisiae var. boulardii in the mixtures tested was crucial for identification using qPCR-HRM analysis and quantitatively corresponded to the strain content in the probiotic-enriched food matrices.

This paper investigates the energy dissipation level of a nonlinear vehicle suspension system. The suspension system is modelled as a mass-spring-damper system, which is designed using the output frequency response function (OFRF) method. This method enables the derivation of an explicit relationship, between the system output spectrum (or Performance metric) and the system nonlinear parameters of interest. The OFRF polynomial, of the energy dissipation level, was derived in terms of the nonlinear parameters of interest. The results obtained show that the OFRF model, of the energy dissipation level, could be used to estimate the amount of heat dissipated, for a set of design parameters. This has potentials of providing some insights, in the design of vibration-based energy harvesters, as some of the wasted heat energy could be converted to electrical energy.

The imperative to achieve carbon neutrality has driven significant advancements in the construction sector, particularly in the production and utilization of building materials. This paper explores innovative strategies and practices designed to reduce the carbon footprint of construction materials, with a focus on both the production processes and the application of sustainable materials. Key innovations include the development of low-carbon and carbon-negative materials, the integration of renewable energy sources in production, and the implementation of advanced recycling technologies. Case studies of successful projects demonstrate how these strategies can be applied in real-world scenarios, highlighting both the benefits and challenges encountered. The analysis also delves into the technical and economic aspects of these innovations, addressing the barriers to their widespread adoption and proposing solutions to overcome these challenges. Through a comprehensive examination of current practices and future trends, this paper aims to provide a roadmap for the construction industry to achieve carbon neutrality, contributing to broader climate change mitigation efforts and fostering a more sustainable built environment.

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) is a promising chemotherapeutic agent because of its selective apoptotic action on cancer cells. However, resistance to TRAIL-induced apoptosis remains a challenge in many cancers. The gintonin-enriched Panax ginseng extract fraction (GEF) has diverse pharmacological benefits. We explored the combined efficacy of GEF and TRAIL in inducing apoptosis in human renal cell carcinoma (RCC) cells. The effect of GEF treatment on viability, clonogenic potential, wound healing, and TRAIL-induced apoptotic signaling of RCC cells was studied in vitro. Our investigation revealed that GEF pre-treatment sensitized RCC cells to TRAIL-induced apoptosis, as evidenced by DNA fragmentation and cell proliferation, colony formation, and migration inhibition. This sensitization was linked to the upregulation of death receptors 4 and 5 and alterations in apoptotic protein expression; notably, decreased expression of Mu-2-related death-inducing gene, a novel anti-apoptotic protein. Our findings underscore the necessity of caspase activation for GEF/TRAIL-induced apoptosis using the pan-caspase inhibitor Z-VAD-FMK. It demonstrates that GEF sensitizes human RCC cells to TRAIL-induced apoptosis by upregulating DR4/5 and modulating apoptotic protein expression. These findings suggest a promising strategy for overcoming TRAIL resistance in cancer therapy and highlight the potential of GEF as a valuable adjunct to TRAIL-based treatments.

Weight loss solutions are on the rise, and there is growing interest in natural alternatives to the pharmaceuticals in the market, which are not devoid of relevant side effects. To this end, the objective of the current study is to assess the effects of a botanical-based blend comprised of lemon verbena and hibiscus extracts in weight management, body fat, appetite, lipid, and glucose profiles, in an overweight population, for 90 days. As a result, the volunteers presented significant weight loss in absence of diet, which coincided with decreased body fat. Body fat was assessed by anthropometry, electrical bioimpedance and DEXA scan. Cholesterol levels were also significantly decreased. Satiety assessment revealed that the product contributed to increased feeling of fullness and satisfaction after a meal, compared to the placebo group, which could contribute to the weight loss observed. Blood glucose and blood pressure levels remained unchanged, which was expected as the volunteers were normoglycemic and their blood pressure was in the healthy range. In conclusion, daily supplementation of a botanical-based blend contributes to weight loss in overweight individuals, in absence of diet, while not affecting other parameters that are in the healthy range. This product could be a candidate alternative or add-on to other weight loss products, as part of a healthy lifestyle.

Arylmagnesium and -calcium reagents are easily accessible, however, ether degradation processes limit the storability especially of the calcium-based heavy Grignard reagents. Ortho-bound substituents with phosphanyl donor sites usually block available coordination sites and stabilize such complexes. The reaction of bromo-2,6-bis(diphenylphosphanylmethyl)benzene (1a) with magnesium in tetrahydrofuran yields [Mg{C₆H₃-2,6-(CH₂PPh₂)₂}₂] (2) after recrystallization from 1,2-dimethoxyethane. However, the similarly performed reduction of bromo- (1a) and iodo-2,6-bis(diphenylphosphanylmethyl)benzene (1b) with calcium leads to ether cleavage and subsequent degradation products. α-Deprotonation of THF yields 1,3-bis(diphenylphosphanylmethyl)benzene. Furthermore, the insoluble THF adducts of dimeric calcium diphenylphosphinate halides, [(thf)₃Ca(X)(µ-O₂PPh₂)]₂ [X = Br (3a), I (3b)], precipitate verifying ether decomposition and cleavage of P-C bonds. Ether adducts of calcium halides [such as [(dme)₂(thf)CaBr₂] (4)] form supporting the initial Grignard reaction and a subsequent Schlenk-type dismutation reaction.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

To obtain carbon dots (CDs) with narrow full width at half maximum (FWHM) and long-wavelength emission, carbon sources with high conjugate sizes and abundant functional groups can be employed to synthesis CDs. In this study, orange-emissive carbon dots (OCDs) were synthesized with phloroglucinol and rhodamine B as precursors. When the molar ratio of them was 30:1 and ethanol was served as solvent, OCDs with optimized emission wavelength at approximately 580 nm, an FWHM of 30 nm and a quantum yield (QY) of 27.31% were obtained. Subsequently, the OCDs were incorporated into polyvinyl alcohol (PVA) to fabricate solid-state OCDs/PVA fluorescent films, which exhibited an FWHM of 47 nm. The PVA matrix facilitated the dispersion of OCDs, thereby suppressing non-radiative energy transfer among the OCDs and enhancing luminescence efficiency. Consequently, compared with OCDs, the OCDs/PVA film exhibited significant luminescent enhancement, and the QY of the composite film was increased to 84.74%. Moreover, OCDs/PVA film show good transmittance and thermal stability. This research offers a solid theoretical and experimental foundation for the potential applications of CDs in the fields of solid-state lighting.

Several types of guided bone regeneration materials are available with various properties and clinical indications. Among them, dentin-derived matrix from extracted teeth is an excellent alternative to traditional graft materials, such as allografts and xenografts. Different clinical preparation protocols exist: block form versus powder form, demineralized versus non-demineralized form. Out of these methods, demineralization protocols for dentin-derived matrix from extracted teeth have been noted for a wide range of successful clinical outcomes. The purpose of this animal study was to find out the most effective method of demineralizing dentin-derived matrix to result in the highest regenerative ability in the bone graft material in rabbit calvaria. The study conducted a comparative histomorphometric analysis of four groups in distinguished matrix conditions: a control group without graft placement, a non-demineralized dentin-derived matrix graft placement group, a 15-minute demineralized dentin-derived matrix graft placement group, and a 30-minute demineralized dentin-derived matrix graft placement group. Regenerative processes were evaluated three times at 2, 4, and 8 weeks post-graft placement. These groups of rabbits were evaluated randomly in a blinded setting to prevent bias. Among the four groups compared, the group with a 15-minute demineralized dentin-derived matrix graft showed the most efficient bone regeneration in the histomorphometric analysis. Based on this animal study, it was apparent that a 15-minute demineralization of dentin-derived matrix is the preferred preparation protocol to maximize the regenerative potential in the matrix.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Presynaptic Ca²⁺-influx through voltage-gated Ca²⁺ channels (VGCC) is a key signal for synaptic vesicle release. Synaptic neurexins can partially determine the strength of transmission by regulating VGCCs. However, it is unknown whether neurexins modulate Ca²⁺-influx via all VGCC subtypes similarly. Here, we performed live cell imaging of synaptic boutons from primary hippocampal neurons with a Ca²⁺-indicator. We used the expression of inactive and active Cre recombinase to compare control to conditional knockout neurons lacking either all or selected neurexin variants. We found that reduced total presynaptic Ca²⁺-transients caused by the deletion of all neurexins were primarily due to the reduced contribution of P/Q-type VGCCs. The deletion of neurexin1α alone also reduced the total presynaptic Ca²⁺-influx but increased Ca²⁺-influx via N-type VGCCs. Moreover, we tested whether the decrease of Ca²⁺-influx induced by activation of cannabinoid receptor 1 (CB1-receptor) is modulated by neurexins. Unlike earlier observations emphasizing a role for β-neurexins, we found that the decrease of presynaptic Ca²⁺-transients induced by CB1-receptor activation depended more strongly on the presence of α-neurexins in hippocampal neurons. Together, our results suggest that neurexins have unique roles in the modulation of presynaptic Ca²⁺-influx through VGCC subtypes and that different neurexin variants may affect specific VGCCs.

This study assesses the performance of calcium aluminate (CAC) and calcium sulfoaluminate (CSA) cement mortars, particularly when blended with fly ash (FA) and limestone powder (LP). The effects of incorporating 20% FA, 15% LP, and their combination (FA 20% and LP 15%), using a water-binder ratio of 0.40 were explored. The study meticulously evaluates the performance of the mortar mixtures in terms of setting time and mechanical properties, including compressive strength, flexural strength, and direct tensile strength. Additionally, the study investigated the alkali-silica reaction (ASR) and autogenous shrinkage. Advanced analytical methods such as X-ray diffraction (XRD), Thermogravimetric Analysis (TGA), and Scanning Electron Microscopy (SEM) were employed to further understand the microstructural changes. The study reveals a significant correlation between compressive, flexural, and direct tensile strengths of the mortar mixtures. Notably, CSA and CAC mortar mixtures with SCMs showed an ASR value lower than the recommended 0.10%, while the autogenous shrinkage for both CAC and CSA mixtures was less compared to Ordinary Portland Cement (OPC). The influence of SCMs, though not substantial, was clearly observed. TGA results corroborated the phases identified in XRD and those observed in SEM, through the thermal decomposition of the phases present in the mixtures. This study contributes valuable insights into the use of SCMs in improving the performance and sustainability of CAC and CSA cement mortars.

The present study showcases a series of crystallization experiments using a specially designed double diffusion system to grow crystals belonging to the calcium carbonate-phosphate system. The experimental U-shaped device comprised two vertical solution containers, separated by a horizontal column of silica hydrogel. Each container was filled with 0.5 M CaCl2 and 0.5 M Na2CO3 solutions, which diffused through the gel column over time. Na3PO4 solutions, with 50 and 500 ppm concentrations, were incorporated into the gel in different experiments, resulting in a homogeneous distribution of phosphate concentrations within the diffusion column. After 15 and 30 days incubation period post-nucleation, the crystals formed in different sections of the gel were carefully extracted and studied with scanning electron microscopy and electron microprobe. Additionally, Raman spectra were collected from the samples using a confocal Raman microscope, providing further insights into their molecular composition and structural properties. The obtained results show that under the induced experimental conditions (i) phosphate incorporates into calcite´s structure, and (ii) the growth of calcium phosphates in the presence of carbonate ions involves the sequential, heterogeneous nucleation of CO3-bearing OCP/HAP-like phases with Raman spectral characteristics very similar to those of bioapatites.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

The calcium-sensing receptor (CAS), as a chloroplast thylakoid membrane protein, involved in the process of [Ca2+] ext-induced [Ca2+]cyt increase (CICI) in the plant. However, the underlying mechanism regulating this process is lacking. Furthermore, recent evidence suggests that CAS may perform additional roles in the plant. Here, we provide an update covering the multiple roles of CAS in stomatal movement regulation and calcium signaling in the plant. We also analysis the possible phosphorylation mechanism of CAS by light and discuss the role of CAS in abiotic stress (drought, salt stress) and biotic stresses (plant immune signaling). Finally, we provide a perspective for future experiments which are required to fill gaps in our understanding of the biological function of CAS in the plant.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

The study of the tribological behavior of the braking system in auto vehicles requires knowing the characteristics of the material in contact and, in the work process, for the friction pair, brake disc-pads. Materials structural analysis is necessary because the wear process depends on the friction pair chemical composition, and brake disk-pads, respectively on the work process parameters (pressing force, rotational speed, traffic conditions, etc.). The material of the brake discs is generally the same gray cast iron, but the brake pads can be semi-metallic (particles of steel, copper, brass, and graphite, all united with a special resin), organic materials (particles of rubber, glass, and kevlar all joined with the help of a resin), composite materials that contain different constituents and ceramic materials (rarely have small copper particles). Therefore, the purpose of the paper is to know the crystalline structure and the mechanical properties of the brake pad materials, through specific studies and analyses, with important implications on the friction and wear behavior.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

Background: Prostate cancer (PCa) is characterized by significant heterogeneity in its molecular, genomic, and immunologic characteristics. Methods: Whole transcriptome RNAseq data from The Cancer Genome Atlas of prostate adenocarcinomas (n=496) was utilized. The immune microenvironment was characterized using the CIBERSORTX tool to identify immune cell type composition. Unsupervised hierarchical clustering was performed based on immune cell type content. Analyses of progression-free survival (PFS), distant metastases, and overall survival (OS) were performed using Kaplan-Meier estimates and Cox-regression multivariable analyses. Results: Four immune clusters were identified, largely defined by plasma cell, CD4+ Memory Resting T Cells (CD4 MR), M0 and M2 macrophage content (CD4 MRHighPlasma CellHighM0LowM2Low, CD4 MRLowPlasma CellHighM0LowM2Low, CD4 MRHighPlasma CellLowM0HighM2Low, and CD4 MRHighPlasma CellLowM0LowM2High). The two macrophage-enriched/plasma cell non-enriched clusters (3&4) demonstrated worse PFS (HR 2.24, 95% CI 1.46–3.45, p=0.0002) than the clusters 1&2. No metastatic events occurred in the non-macrophage-enriched clusters. Comparing clusters 3 vs 4, in patients treated by surgery alone, cluster 3 had zero progression events (p<0.0001). However, cluster 3 patients had worse outcomes after post-operative radiotherapy (p=0.018). Conclusion: Distinct tumor immune clusters with a macrophage-enriched phenotype and reduced plasma cell enrichment independently characterize an aggressive phenotype in localized prostate cancer that may differentially respond to treatment.

Yttria stabilized zirconia materials are frequently used in mechanical engineering and biomedical applications. Demanding loading conditions require materials combining a high level of strength and fracture toughness. A ready to press alumina doped 2 mol% yttria stabilized zirconia powder was shaped by axial pressing and sintering in air at 1250 - 1500 °C for 2 h. The best combination of strength and toughness value of 7.8 MPa√m. Materials sintered in the middle of the chosen temperature range combine fully density, high transformability and small grain size. Toughness measurements by direct crack length measurements delivered unrealistically high fracture toughness values.

Traditional painting artefacts study and documentation face the limitations of well-known recording tools and methods, such as handwritten or digital descriptions, scaled 2D drawings in situ, measurements with calipers, rulers or tape measures, sketches, tracings, as well as conventional or technical photographs. This paper advocates Close-Range Photogrammetry (SfM-MVS) and Reflectance Transformation Imaging (RTI) for recording vital morphological and 2.5D geometric features of painted surfaces with high accuracy. These digital tools, widely accessible due to increased computing power, enhance art observation, material study and conservation assessment. Despite specialized alternatives like 3D laser scanners, the focus here is on the cost-effective SfM-MVS and RTI, which offer advanced pixel colour accuracy. The ability to reproduce photorealistic textures proves essential for accurate documentation of painted artefacts. The paper showcases promising results from applying these methods to a mural from the Palace of Tiryns, justifying their fundamental role in an integrated scientific art study methodology.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

B chromosomes are supernumerary chromosomes which are found in addition to the normal standard chromosomes (A chromosomes). B chromosomes are well known to accumulate several types of repeats. Although the evolution of B chromosomes has been subject of numerous studies, the mechanisms of accumulation and evolution of repetitive sequences is not fully understood. Recently, new genomic approaches have shed light on the origin and accumulation of different classes of repetitive sequences in the process of B chromosome formation and evolution. Here we discuss the impact of repetitive sequences accumulation on the evolution of plant B chromosomes.

K-band radar waves have high penetration and low attenuation coefficients. However, the wavelength of this radar wave is relatively short; thus, designing and preparing both broadband and wide-angle radar wave absorbers in this band presents considerable challenges. In this study, a resin-based K-band radar wave absorber with a biomimetic lotus leaf structure was designed and formed by UV curing. Here, microscale lotus leaf papillae and antireflection structures were prepared using a DLP 3D printer, and the contact angle between the material and water droplets was increased from 56° to 130°. In addition, the influence of the geometric parameters of the lotus leaf antireflection structure on the electromagnetic absorption performance and mechanical strength was investigated. After simulation optimization, the maximum electromagnetic loss of the lotus leaf structure 3D printed sample was −32.3 dB, and the electromagnetic loss was below −10 dB in the 20.8–26.5 GHz frequency range. When the radar incidence angle was 60°, the maximum electromagnetic loss was still less than −10 dB. The designed lotus leaf structure has a higher mechanical energy absorption per unit volume (337.22 KJ/m3) and per unit mass (0.55 KJ/Kg) than commonly used honeycomb lightweight structures during the elastic deformation stage, and we expect that the designed structure can be used as an effective lightweight material for K-band radar stealth.

Objective: The aim of study is to find key genes and enriched pathways associated with lung cancer. Participants and Methods: Differentially expressed genes (DEGs) data of 54674 genes based on stage, tumor and status of lung cancer was taken from 66 patients of African American (AAs) origin. 2392 DEGs were found based on stage, 13502 DEGs were found based on tumor, 2927 DEGs were found based on status having p value (p<0.05). Results: Total 33 common DEGs were found from stage, tumor and status of lung cancer. Gene ontology (GO) and KEGG pathway enrichment analysis was performed and 49 significant pathways were obtained, out of which 10 pathways were found to be exclusively involved in lung cancer development. Protein-protein interaction (PPI) network analysis found 69 nodes and 324 edges and identified 10 hub genes based on their highest degrees. Module analysis of PPI found that ‘Viral carcinogenesis’, ‘pathways in cancer’, ‘notch signaling pathway’, ‘AMPK signaling pathways’ had a close association with lung cancer. Conclusion: These identified DEGs regulate other genes which play important role in growth of lung cancer. The key genes and enriched pathways identified can thus help in better identification and prediction of lung cancer.

Abstract. Graphene family (GF)-Calcium phosphate (CaP) composites, holds great potential as components of bone regeneration materials. GF nanomaterials can be modified physically as well as chemically, which are to be biomimetic, mechanically to be hard due to their capability to support exceptional mechanical, thermal and electronic properties. These biocompatible GF composites coated on the calcium phosphate can enhance and tolerate stem cell growth and differentiation, proliferation into various lineages or interact with bioorganisms. The development in CF-CaP materials and their physicochemical/biointeractions and strategies towards osteoblasts is a great concern to promote faster healing and reconstructions of large bone imperfections or defects. In this review, we explain the influence of the CF-CaP and summarize recent developments on designing CF-CaP architectures as multifunctional bone regeneration platforms. We have also explored the typical biological applications concerning these CF-CaP based bioactive nanocomposites. Furthermore, the future viewpoints and evolving challenges will also be emphasized. Due to the shortage of full-length reviews in this emerging research field, this review would be caught great attention and encourage various new chances across a wider range of disciplines.

This study evaluated the effect of newly introduced calcium silicate-based temporary intracanal medicament Bio-C Temp and calcium hydroxide-based material UltraCal XS on the release of transforming growth factor β1 (TGF-β1) from root canal dentin. Twenty-two intact and fully developed human premolars from patients aged 15 – 18 were shaped and irrigated according to the current clinical recommendations. The teeth were then gently split in half, and the root canal dentin of paired samples was covered with Bio-C Temp or UltraCal XS. After 3 weeks of incubation, the specimens were conditioned with 17% EDTA and the collected solution was subjected to quantification of released TGF-β1 by performing ELISA. One-way analysis of variance (ANOVA), followed by Tukey’s test, was selected to determine the statistically significant differences between the groups at the 0.95 confidence level. The highest mean value of released TGF-β1 (1993.1 pg/ml) was detected in the control group, where root canal dentin was conditioned with 17% EDTA alone. Regarding experimental groups, Bio-C Temp released a statistically significant higher amount of TGF-β1 (282.14 pg/ml) compared to UltraCal XS (114.28 pg/ml; p = 0.0158). Bio-C Temp affected the release of growth factors from root canal dentin less than UltraCal XS and may therefore serve as an intracanal medicament for regenerative endodontic procedures.

'Cv 'Doña María' table grape is a high-quality table grape variety included in the Protected Designation of Origin (PDO) of the European Union "The bagged grape of the Vinalopó." The PDO stipulates that grape clusters must be protected with paper bags from inclement weather and insects, which helps enhance the final grape quality. However, 'Doña María' is a variety prone to high shattering in the late stages of ripening on the vine and during postharvest. Inorganic calcium treatments are one of the most commonly used tools to reduce this disorder, but the translocation of this mineral from veraison onward has been questioned. In this study, five applications were performed, from veraison to harvest, using sorbitol-chelated calcium (0.7 % + 1.0 %), Ca(NO3)2 (Ca) at 0.7% and sorbitol at 1%. It was observed that bagged grapes (not wetted with the solutions) only increased the concentration of total and bound calcium when treated with Sorbitol-Ca. This resulted in reduced berry drop during cultivation and postharvest and improved fruit firmness. Additionally, it reduced grape metabolism indicators such as respiration rate, weight loss, malic acid degradation, prevented abscisic acid (ABA) and malondialdehyde (MDA) accumulation, and favored the accumulation of secondary metabolites such as total polyphenols, increased antioxidant activity, and sugar content. The application of sorbitol-chelated calcium is an effective and safe tool that enhances fruit quality and prevents losses due to shattering during postharvest.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Microplastics (MPs) are a critical environmental issue, with impacts ranging from ecosystem contamination to health risks through bioaccumulation. This review addresses the inefficacy of traditional water treatments in removing MPs and proposes photodegradation, particularly via nanomaterial-enhanced photocatalysts, as a solution. Utilizing their unique properties like large surface area and tunable bandgap, nanomaterials significantly improve degradation efficiency. Different strategies for photocatalysts modification to improve photocatalytic performance are thoroughly summarized, with the particular emphasis on element doping and heterojunction construction. Furthermore, this review thoroughly summarizes the possible fundamental mechanisms driving photodegradation of microplastics facilitated by nanomaterials, with a focus on processes like free radical formation and singlet oxygen oxidation. By clearly elucidating these strategies and mechanisms, this review aims to provide valuable insights and inspire further progress in microplastic photodegradation.

Powders with phase composition including syngenite K2Ca(SO4)2·H2O and/or calcium sulfate di-hydrate (gypsum) CaSO4·2H2O were synthesized from powder of calcium carbonate CaCO3 and water solutions of potassium hydrosulfate KHSO4 of various (0.5M, 1M and 2M) concentrations. Molar ratio of starting salt KHSO4/CaCO3=2 were used to provide formation of syngenite K2Ca(SO4)2·H2O. But when using 0.5M water solution of potassium hydrosulfate KHSO4 the phase composition of synthesized powder was presented by calcium sulfate dihydrate (gypsum) CaSO4·2H2O. When using 1M and 2M water solution of potassium hydrosulfate KHSO4 the syn-genite K2Ca(SO4)2·H2O was found as predominant phase in synthesized powders. According es-timations made from thermal analysis data when 1.0M and 2.0M water solutions of potassium hydrosulfate KHSO4 were used the content of calcium sulfate dihydrate (gypsum) CaSO4·2H2O in these powders were not higher then as 7.9 and 1.9 % respectively. Phase composition of products isolated from mother liquors via water evaporation consisted of syngenite K2Ca(SO4)2·H2O and potassium sulfate (arcanite) K2SO4. Synthesized powders can be used in preparation of biocom-patible bioresorbable materials with phase composition in the K2O‑CaO‑SO3‑H2O system; as matrix of thermo- or photo-luminescent materials; as components reducing the setting time and increasing strength of sulfate cements; in the fertilizing industry and also as a components of Martian regolith simulant.

Voltage-gated Ca²⁺ (Ca_v) channels play pivotal roles in regulating gene transcription, neuronal excitability, and neurotransmitter release. In order to meet the spatial and temporal demands of visual signaling, Ca_v channels exhibit unusual properties in the retina compared to their counterparts in other areas of the nervous system. Here, we review current concepts regarding the specific subtypes of Ca_v channels expressed in the retina, their intrinsic properties and forms of modulation, and how their dysregulation could lead to retinal disease.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

Calcium sulphate (CS) is currently used as a bioabsorbable, completely synthetic and sterile material in the management of infected tissues and dead spaces (DS) mainly resulting from surgical procedures. Residual DS in the postoperative, may create an environment where hematomas fill up and bacteria can proliferate, leading to a high incidence of postoperative infections. Considering the available reviews in the literature, CS has been mainly studied in orthopedic surgery mostly giving brilliant results and low complication rates. Nowadays, orthopedists avail it in the form of pearls both as a bone void filler and as an “off-label” delivery agent for antibiotics in arthroplasty, chronic osteomyelitis and open fractures, paving the way of its application in many other contexts given its natural dis-position to biodegradation. In the last years, CS beads have been gaining ground in the general, vascular and endocrinological surgical specialties. Despite its clear potential and the increasing number of scientific evidences on the safety and effectiveness of CS application in the prophylaxis and treatment of infections, there are not many studies reporting on its application in fields other than orthopedics, with a substantial paucity in plastic and reconstructive surgery literature. This is some-how surprising, since reconstructive surgery often deals with complex wounds secondary to bone and soft tissue exposure, suture dehiscence, trauma, and surgical site infections. As far as we know this is the first updated systematic review assessing the state of the art, indications and new perspectives on the application of CS beads in plastic and reconstructive surgery.

Hypertension is a frequent risk factor for cardiovascular diseases and the prevalence rate is continuously rising. Multiple pathophysiological mechanisms are responsible for hypertension, necessitating a combination of drugs from different classes for best management. Combination therapy is five times more effective in decreasing blood pressure compared to escalating the dose of a single agent. As per the ACCOMPLISH trial analysis, coupling a renin-angiotensin system inhibitor with a calcium channel blocker is more effective than the combination of a renin-angiotensin system inhibitor with diuretics in reducing major cardiovascular events, cardiovascular-related mortality, and the progression of chronic kidney disease. The renin-angiotensin system can be suppressed by inhibiting the angiotensin-converting enzyme or angiotensin type 1 receptor (AT1R), resulting, in decreased vascular smooth muscle contraction, heart performance, and reduced aldosterone synthesis. Calcium channel blockers work by inhibiting L-type calcium channels, reducing heart performance via negative inotropic, chronotropic, and bathmotropic effects, along with reducing vascular smooth muscle contraction. Diuretics exert their antihypertensive impact by changing body fluid volume and electrolytes. Initially, hypertension treatment commences with a single medication but often, different classes of two or more antihypertensive medications are necessary for achieving the target blood pressure goal. Sometimes, for Resistant hypertension four different classes of antihypertensive medications are necessary to reach the target blood pressure goal.

Behavior analysis is a widely used non-invasive tool in the practical production routine, as the animal acts as a biosensor capable of reflecting its degree of adaptation and discomfort to some environmental challenge. Predominantly, conventional statistics use occurrence data for behavioral evaluation and well-being estimation, disregarding the temporal sequence of events. The Generalized Sequential Pattern (GSP) algorithm is a data mining method that identifies recurrent sequences that exceed a user-specified support threshold, whose potential has not yet been investigated for broiler chickens in enriched environments. Enrichment aims to increase environmental complexity with promising effects on animal welfare, stimulating priority behaviors and potentially reducing the deleterious effects of heat stress. The objective was to validate the application of the GSP algorithm to identify temporal correlations between heat stress and the behavior of broiler chickens in enriched environments through proof of concept. Video image collection was carried out automatically for 48 continuous hours, analyzing a continuous period of seven hours, from 12:00 PM to 6:00 PM, during two consecutive days of tests for chickens housed in enriched and non-enriched environments under comfort and stress temperatures. Chickens at comfort temperature showed high motivation to perform the behaviors of Preening (P), Foraging (F), Lying down (Ld), Eating (E), and Walking (W) whose sequences &lt;{Ld,P}&gt;; &lt;{Ld,F}&gt;; &lt;{P,F,P}&gt;; &lt;{Ld,P,F}&gt; and &lt;{E,W,F}&gt; were the only ones observed in both treatments. All other sequential patterns (comfort and stress) were distinct, suggesting that environmental enrichment alters the behavioral pattern of broiler chickens. Heat stress drastically reduced the sequential patterns found at the 20% threshold level in the tested environments. The behavior of lying laterally "Ll" is a strong indicator of heat stress in broilers and was only frequent in the non-enriched environment, which may suggest that environmental enrichment provides the animal with better opportunities to adapt to stress-inducing challenges, such as heat.

The increasing use of energy resources recovered from the subsurface environments and the resulting carbon imbalance in the environment has motivated the need to develop thermodynamically downhill pathways to convert and store CO₂ as water insoluble calcium or magnesium carbonates. While previous studies extensively explored aqueous routes to produce calcium and magnesium carbonates from CO₂, there has been a limited scientific understanding of the phase evolution and textural changes during the direct gas-solid conversion routes to produce calcium carbonate from calcium hydroxide, which is one of the abundant constituents of alkaline industrial residues. With increasing interest in developing integrated pathways for capturing, converting and storing CO₂ from dilute flue gases, understanding the compositions of the product phases as they evolve is essential for evaluating the efficacy of a given processing route. Therefore, in this study, we investigate the phase evolution and the corresponding textural changes as calcium hydroxide is converted to calcium carbonate under the continuous flow of CO₂ at an ambient pressure of 1 atm and on heating continuously from 30 °C to 500 °C using in-operando wide angle X-ray scattering (WAXS), small angle X-ray scattering (SAXS), and ultra-small angle X-ray scattering (USAXS) measurements.

Ca2+ can boost protein-protein interactions and, if present at an appropriate level, can potentially improve the physicochemical properties of protein gels and films. This study aimed to determine the effect of CaCl2 (0, 0.01 0.025 0.05% w/w) on the optical, water affinity, and mechanical char-acteristics of glycerol (Gly)- and sorbitol (Sor)-plasticized pea protein isolate (PPI) films. The CaCl2 caused darkening and a color shift of the films from yellow to yellow-green. Additionally, de-creased light transmission, particularly in the UV range, and reduced moisture content were observed. The CaCl2 decreased the water vapor permeability (WVP) of the Gly-plasticized film by an average of 20%, with no effect on the Sor-plasticized film. All films were completely soluble in water. The CaCl2 negatively impacted the mechanical integrity of the films, reducing the tensile strength of the Gly- and Sor-plasticized films by ~16% and 14-37%, respectively. Further increases in CaCl2 content (0.1% and 0.2% w/w) led to concentration-dependent cracks, suggesting protein over-crosslinking. In summary, the incorporation of CaCl2 into PPI films did not provide signif-icant benefits and actually worsened key properties such as transparency and mechanical strength. The type of plasticizer influenced how CaCl2 affected some properties of the PPI film.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Ceramic samples based on b-calcium pyrophosphate b-Ca2P2O7 were prepared using firing at 900, 1000, and 1100 oC from powders of g-calcium pyrophosphate g-Ca2P2O7 with preset molar ratios Ca/P=1; 0,975 and 0,95. To prepare powders of g-calcium pyrophosphate g-Ca2P2O7 with preset molar ratio Ca/P=1; 0,975 and 0,95 powder mixtures based on calcium lactate pentahydrate Ca(C3H5O3)2⋅5H2O and, monocalcium phosphate monohydrate Ca(H2PO4)2⋅H2O were treated in an aqua medium in mechanical activation conditions, dried, disaggregated in acetone, and heat-treated at 600 oC. The phase composition of powder mixtures after treatment if planetary mill in aqua medium included both brushite CaHPO4⋅2H2O or monetite CaHPO4, and starting salts. The phase composition of all powder mixtures after disaggregation in acetone in planetary mill included monetite CaHPO4 and starting salts. After heat treatment at 600 oC according to the XRD data phase composition of all powder mixtures was presented by g-calcium pyrophosphate g-Ca2P2O7. The grain size of ceramics increased both with the growth of firing temperature and with decreasing of molar ratio Ca/P of powder mixtures. Calcium polyphosphate (t melt =960–968 oC) formed from monocalcium phosphate monohydrate Ca(H2PO4)2⋅H2O acted like a liquid phase sintering additive. It was confirmed by tests in vitro, that prepared ceramic materials with preset molar ratio Ca/P=1; 0,975 and 0,95 and phase composition presented by b-calcium pyrophosphate b-Ca2P2O7 according to XRD data were biocompatible and could maintain bone cells proliferation.

The etiology of Autism Spectrum Disorder (ASD) has been linked to both genetic and epigenetic factors. Among the epigenetic factors, exposure to valproic acid (VPA), an antiepileptic and mood-modulating drug, has been shown to induce characteristic traits of ASD when exposed during embryogenesis. Conversely, in animal models, Enriched Environment (EE) has demonstrated positive behavioral and neural effects, suggesting its potential as a complementary treatment to pharmacological approaches in central nervous system disorders. In this study, we utilized zebrafish to model ASD characteristics induced by VPA and hypothesized that sensory stimulation through EE could ameliorate the behavioral and neuroanatomical features associated with ASD. To test this hypothesis, we assessed social behavior, cerebellar volume, and Purkinje cell populations via histology and immunohistochemistry after exposing the fish to EE. The results revealed that zebrafish exposed to VPA exhibited social deficits, reduced cerebellar cortex volume, and a decrease in c-Fos-positive cells in the Purkinje layer. In contrast, VPA-exposed fish treated with EE showed increased socialization, augmented cerebellar cortex volume, and an elevation in c-Fos-positive Purkinje cells. These findings suggest that alterations induced by VPA may be ameliorated through EE treatment, highlighting the potential therapeutic impact of sensory stimulation in conditions related to ASD.

Environmental concerns, among other causes, are leading to meat replacement in the diet by healthy, nutritious and tasty foods. Alternative protein sources of plant origin can be an alternative to meat, but their low biological value proteins can be a problem. Novel foods, such as insect meals, can meet currently consumer demands. Therefore, this research has developed innovative prototypes of analogue burgers with animal and vegetable proteins. Concerned about health and allergies, a prototype incorporating soya to satisfy coeliacs was developed. An iterative and heuristic process was carried out to test the product development feasibility. The main raw materials used were insect flour (Tenebrio molitor), seitan and soya. In addition, oat and sodium alginate were used as binders. Shelf-life of the new product was evaluated by physicochemical (pH, aw, moisture, colour, acidity and peroxide index) and sensory analysis (quantitative analysis -QDA-). The production of the burger analogues was feasible. Product characterisation showed significant differences (p < 0.05) among samples for organoleptic properties, highlighting texture changes. Using a multivariate model, it was established “The best before date” at 7 days for all developed prototypes, conditioned by microbial growth. Finally, the spoilage model indicated an important contribution to bacterial growth with a notable modification in the pastiness and hardness of the burger analogues developed.

A useful perioperative nutritional therapy for highly invasive esophageal cancer surgical cases needs to be developed. We clarified the usefulness of amino acid-enriched nutritional therapy using glutamine (Gln)/arginine (Arg)/calcium β-hydroxy-β-methylbutyrate (HMB) products on the short-term postoperative outcomes of minimally invasive esophagectomy for esophageal cancer. Altogether, 114 patients (Gln/Arg/HMB group) received perioperative nutritional therapy with Gln/Arg/HMB products, and we retrospectively investigated the change in nutritional parameters including skeletal muscle mass, occurrence of postoperative complications, and short-term postoperative outcomes in this group. The results were compared between the Gln/Arg/HMB and control groups (79 patients not receiving the Gln/Arg/HMB products). The incidence of all postoperative complications, sputum expectoration disorder, and pleural effusion of grade ≥III was significantly lower in the Gln/Arg/HMB group (62.0% vs. 38.6%, p = 0.001; 44.3% vs. 28.1%, p = 0.020; 27.8% vs. 13.2%, p = 0.011, respectively). The psoas muscle area and postoperative body weight was significantly higher at 1 month and 1 year after surgery in the Gln/Arg/HMB group than in the control group (93.5% vs. 99.9%, p &lt; 0.001; 92.0% vs. 95.4%, p = 0.006). Perioperative amino acid-enriched nutritional therapy may improve the short-term postoperative outcomes, nutritional status, and skeletal muscle mass of esophageal cancer surgical patients.

Recent research efforts in bone tissue engineering have been primarily directed towards manufacture-viable synthesis of biomaterials that can significantly enhance the biocompatibilities and osteogenic capabilities on the new biomaterials. This paper presents a straightforward, cost-effective, optimized, and well-controlled hydrothermal synthesis of Nb-doped potassium titanate nanofibers in high-purity. Characterization data revealed that the Nb-doping potassium titanate maintained the crystal structure, showing great promise for applications in bone tissue engineering.

This work proposes a methodology for the design, development, optimisation, and evaluation of amorphous rosuvastatin calcium tablets (BCS class II drug). The main goal was to ensure rapid disintegration and high dissolution rate of the active ingredient, thus enhancing its bioavailability. The design started from a careful selection of excipients, which due to their characteristics and proportions within the formulation allowed the use of their properties such as fluidity or granulometric distribution. The formulation was characterised using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetry (TGA), Fourier transform infrared spectroscopy (FT-IR) and powder X-ray diffraction (PXRD) methods. The galenic SeDeM methodology was used to establish the profile of the active ingredient-excipient mixture and guarantee its suitability for producing tablets by the direct compression method. The results demonstrate that the amorphous rosuvastatin calcium tablets formulation developed made it possible to obtain cost-effective tablets by direct compression with optimal pharmacotechnical characteristics that showed a remarkable disintegration and dissolution rate. The manufactured tablets complied with the pharmacopoeia guidelines regarding uniformity of weight, tablet hardness, thickness, friability, in vitro disintegration time and dissolution profile.

Tinnitus is a heterogeneous auditory disorder without a pharmacological cure but with several palliative treatments. One of the most applied treatments for tinnitus relief combines counselling with sound therapy. The efficiency of this sound therapy depends on the type of sound stimulus and the exposition time. The fundamentals of a customized sound therapy that stimulates the auditory system with a continuous or sequential sound which compensates for the subject hearing loss are described here. A sample of 137 tinnitus subjects are treated with this sound therapy, named Enriched Acoustic Environment. 90% of these patients achieved a clinically relevant and statistically significant tinnitus-related distress relief quantified as a mean drop of their Tinnitus Handicap Inventory score of 24.3 points. These subjects exposed with sequential stimuli (31%) achieved greater distress relief (5.1 points more in their Tinnitus Handicap Inventory score) than those stimulated with continuous sound (69%). Therefore, this sound constitutes an optimized stimulus for tinnitus treatment.

Transmembrane protein 100 (TMEM100) plays an important role in angiogenesis, vascular morphogenesis, integrity and cardiovascular development. TMEM100 is a downstream target of the BMP9/10 and BMPR2/ALK1 signaling pathways. Our recent study demonstrates TMEM100 is a lung endothelium enriched gene. Endothelial-specific deletion of Tmem100 impairs lung endothelial cells regeneration. Activation of Tmem100 signaling represents a novel strategy for lung vascular repair and regeneration. It is interesting and important to understand the roles of TMEM100 in the physiological and pathological conditions. In this review, we summarized the current knowledge of TMEM100.

36 years after the publication of the important article by Busa and Nuccitelli on the variability of intracellular pH (pH_i) and the interdependence of pH_i and intracellular Ca²⁺ concentration ([Ca²⁺]_i), little research has been carried out on pH_i and calcium signaling. Moreover, the results appear to be contradictory. Some authors claim that the increase in [Ca²⁺]_i is due to a reduction in pH_i, others that it is caused by an increase in pH_i. The reasons for these conflicting results have not yet been discussed and clarified in an exhaustive manner. Variations in pH_i have a significant impact on the increase in [Ca²⁺]_i and hence on some of the basic biochemical mechanisms of calcium signaling. This paper focuses on the possible triggering role of protons, highlighting the mechanisms potentially involved and the open issues that could be clarified by research.

Background: Previous papers have developed a statistical mechanics of neocortical interactions (SMNI) fit to short-term memory and EEG data. Adaptive Simulated Annealing (ASA) has been developed to perform fits to such nonlinear stochastic systems. An N-dimensional path-integral algorithm for quantum systems, qPATHINT, has been developed from classical PATHINT. Both fold short-time propagators (distributions or wave functions) over long times. Previous papers applied qPATHINT to two systems, in neocortical interactions and financial options. Objective: In this paper the quantum path-integral for Calcium ions is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Using fits of this SMNI model to EEG data, including these effects, will help determine if this is a reasonable approach. Method: Methods of mathematical-physics for optimization and for path integrals in classical and quantum spaces are used for this project. Studies using supercomputer resources tested various dimensions for their scaling limits. In this paper the quantum path-integral is used to derive a closed-form analytic solution at arbitrary time that is used to calculate interactions with classical-physics SMNI interactions among scales. Results: The mathematical-physics and computer parts of the study are successful, in that there is modest improvement of cost/objective functions used to fit EEG data using these models. Conclusions: This project points to directions for more detailed calculations using more EEG data and qPATHINT at each time slice to propagate quantum calcium waves, synchronized with PATHINT propagation of classical SMNI.

An undesirable sensory attribute (“floral taint”) has been recently detected in red wines in some winegrowing jurisdictions in North America (e.g. Ontario, British Columbia, Washington), caused by introduction of frost-killed leaves and petioles [materials-other-than-grapes (MOG)] during mechanical harvest and winemaking. It was hypothesized that terpenes, norisoprenoids, and higher alcohols would be the main responsible compounds. Objectives were to investigate causative volatile compounds for floral taint, and explore threshold concentrations for this problem. Commercial wines displaying varying intensities of floral taints were subjected to GC-MS and sensory analysis. Several odor-active compounds were higher in floral-tainted wines, including terpenes (geraniol, citronellol, cis- and trans-rose oxide), norisoprenoids (β-damascenone, β-ionone), five ethyl esters, and three alcohols. Thereafter, fermentations of Cabernet franc (CF) and Cabernet Sauvignon (CS) (2016, 2017) were conducted. MOG treatments were (wt/wt): 0, 0.5%, 1%, 2% and 5% petioles, and 0, 0.25%, 0.5%, 1%, and 2% leaf blades. Terpenes (linalool, geraniol, nerol, nerolidol, citronellol, citral, cis- and trans-rose oxides, eugenol, myrcene), norisoprenoids (α- and β-ionone), and others (e.g. hexanol, octanol, methyl and ethyl salicylate) increased linearly/quadratically with increasing MOG levels in both cultivars. Principal components analysis separated MOG treatments from the controls with 5% petioles and 2% leaves as extremes. Increasing MOG levels in CF wines increased floral aroma intensity, and were primarily associated with terpenes, higher alcohols, and salicylates. Increased leaf levels in CF were associated with higher vegetal and earthy attributes. Increased petioles in CS were not correlated with floral aromas, but increased leaves increased floral, vegetal and herbaceous attributes. Overall, petioles contributed more to floral taint than leaves through increased terpenes and salicylates (floral notes), while leaves contributed norisoprenoids and C6 alcohols (green notes).

Low dietary intake of calcium, vitamin D, vitamin C and magnesium has been associated with increased risk of osteoporosis. The purpose of the study was to evaluate changes in several bone health indicators and metabolic biomarkers in postmenopausal women, with high osteopenia or osteoporosis, followed by a nutritional intervention program. 115 apparently healthy postmenopausal women (52±8 years old) were randomized into four groups: group I (n=40) received daily 1000 mg vitamin C, 100 mcg vitamin D3, 500 mg calcium(Ca) and 300 mg magnesium (Mg); group II (n=42) received daily 100 mcg vitamin D3, 500 mg Ca and 300 mg Mg; group III (n=18) received daily 5 mg bisphosphonates, 100 mcg vitamin D3, 500 mg Ca and 300 mg Mg; and group IV (n=15) received daily about 364 mg polyphenols via an innovative functional food (50 g olive paste enriched with mountain tea extract) along with 100 mcg vitamin D3, 500 mg Ca and 300 mg Mg. Groups I -III received supplementation for a year whereas group IV for 5 months. Changes in bone health indicators and metabolic biomarkers were assessed at the beginning and at the end of the study. Anthropometric indices and whole-body bone mineral density (BMD) were also evaluated at the beginning and at the end of the intervention period. The results revealed improved elevated levels of 25(OH)D3, in groups II, III and IV (+3,71% and +1.45% and +5.62% respectively). Significant positive changes were recorded, for whole-body BMD, in all four study groups. Significant beneficial changes for total cholesterol were observed in group IV (-2.07%, P&lt;0.05) and positive changes in group I for HDL biomarker (+61.62%, P&lt;0.05). Additional larger-scale clinical trials and intervention studies are considered essential, to fully investigate and elucidate associations between dietary components and biochemical indices of bone health.

Nano- and microparticles are increasingly widely used in biomedical research and applications, particularly as specific labels and targeted delivery vehicles. Silica has long been considered the best material for such vehicles, but it has some disadvantages limiting its potential, such as the proneness of silica-based carriers to spontaneous drug release. Calcium carbonate (CaCO3) is an emerging alternative, being easily available, cost-effective, biocompatible material with high porosity and surface reactivity, which makes it an attractive choice for targeted drug delivery. CaCO3 particles are used in this field in the form of either bare CaCO3 microbeads or core/shell microparticles representing polymer-coated CaCO3 cores. In addition, they serve as removable templates for obtaining hollow polymer microcapsules. Each of these types of particles has its specific advantages in terms of biomedical applications. CaCO3 microbeads are primarily used due to their capacity for carrying pharmaceutics, whereas core/shell systems ensure better protection of the drug-loaded core from the environment. Hollow polymer capsules are particularly attractive because they can encapsulate large amounts of pharmaceutical agents and can be so designed as to release their contents in the target site in response to specific stimuli. This review focuses first on the chemistry of the CaCO3 cores, core/shell microbeads, and polymer microcapsules. Then, systems using these structures for the delivery of therapeutic agents, including drugs, proteins, and DNA, are outlined. The results of systematic analysis of available data are presented. They show that the encapsulation of various therapeutic agents in CaCO3-based microbeads or polymer microcapsules is a promising technique of drug delivery, especially in cancer therapy, enhancing drug bioavailability and specific targeting of cancer cells while reducing side effects. To date, research in CaCO3-based microparticles and polymer microcapsules assembled on CaCO3 templates has mainly dealt with their properties in vitro, whereas their in vivo behavior still remains poorly studied. However, an enormous potential of these highly biocompatible carriers for in vivo applications is undoubted. This last issue is addressed in depth in the Conclusion and Outlook sections of the review.

The material properties and structural characteristics of ballistic composites are crucial to their ballistic performance. Investigation for the influence of the material and structural parameters of UHMWPE body armor on anti-fragmentation penetration performance has been made by numerical simulation in this paper, with a numerical modeling simulating the penetration of a 1.1 g FSP into the target plate of UHMWPE body armor, by which the simulation results demonstrate that the failure process of the body armor target plate primarily involves shear damage, interlayer delamination, and tensile damage. Furthermore, the study evaluates the effects of elastic modulus, tensile strength, shear strength, number of layers, and interlayer strength on the ballistic limit velocity of UHMWPE body armor. The findings reveal that the ballistic limit velocity is most sensitive to changes in shear strength, with variation rates ranging from -18.02% to 10.81%, showing an approximate positive correlation, while the elastic modulus has the smallest impact on ballistic limit velocity, with variation rates ranging from -1.8% to 3.6%. Additionally, appropriate interlayer strength can improve the ballistic limit velocity of the body armor to a certain extent. This study provides theoretical methods and recommendations for optimizing anti-penetration performance of UHMWPE body armor.

Mixed plastic packaging waste sorting residues (MPO323) were treated by thermal pyrolysis to utilize pyrolysis oil and char. The pyrolysis oil was found to contain aromatic and aliphatic hydrocarbons. Chlorine and bromine contents were up to 40,000 mg/kg and 200 mg/kg, respectively. Additionally, other elements like sulfur, phosphorous, iron, aluminum, and lead were detected, which can be interpreted as impurities regarding the utilization of the oils by means of chemical recycling. The pyrolysis char showed high contents of potentially active species like silicon, calcium, aluminum, iron, and others. To enhance the content of aromatic hydrocarbons and to reduce the level of contaminants, the pyrolysis oil was reformed with the corresponding pyrolysis char to act as an active material in a fixed bed. The temperature of the reactor and the flow rate of the pyrolysis oil feed were varied to gain insights on cracking and reforming reactions as well as on the performance with regard to decontamination.

Research on piezo-composite actuators has been actively conducted over the past two decades as a response to strong demand for light, compact actuators to replace electro-magnetic motor actuators in micro robots, small flying drones, and compact missile systems. Layered piezo-composite unimorph actuators have been studied to provide active vibration control of thin-walled aerospace structures, control the shapes of aircraft wing airfoils, and control the fins of small missiles, because they require less space and provide better frequency responses than conventional electro-magnetic motor actuator systems. However, based on the limited actuation strains of conventional piezo-composite unimorph actuators with poly-crystalline piezoelectric ceramic layers, they have not been implemented effectively as actuators for small aerospace vehicles. In this study, a lightweight piezo-composite unimorph actuator (LIPCA-S2) was manufactured and analyzed to predict its flexural actuation displacement. It was found that the actuated tip displacement of a piezo-composite cantilever could be predicted accurately using the proposed prediction model based on the nonlinear properties of the piezoelectric strain coefficient and elastic modulus of a piezoelectric single crystal.

The homeostasis of cellular calcium is fundamental for many physiological activities, while calcium levels maintain inhomogeneous within cells. During the onset of asthma, epithelial and inflammatory cells secrete platelet derived growth factor (PDGF), inducing proliferation and migration of airway smooth muscle (ASM) to the epidermal layer, narrowing the airway. The regulation of ASM cells by PDGF is closely related to the conduction of calcium signals. In this work, we generated subcellular-targeted FRET biosensors to investigate calcium regulations at different compartments of ASM cells. PDGF-induced cytoplasmic calcium [Ca2+]C increase was attributed from both extracellular calcium influx and endoplasmic reticulum (ER) calcium [Ca2+]ER release, which was partially regulated by PLC-IP3R pathway. Interestingly, removal of extracellular calcium influx led to inhibited ER calcium release, likely through inhibitory effect on calcium-dependent activation of ER ryanodine receptor. Inhibition of L-type calcium channel on plasma membrane, or SERCA pump on ER resulted in both reduced [Ca2+]C and [Ca2+]ER from PDGF stimulation, while IP3R channel inhibition led to reduced [Ca2+]C only. Inhibited SERCA pump caused immediate [Ca2+]C increase and [Ca2+]ER decrease, indicating an active calcium exchange between cytosol and ER storage in resting cells. PDGF-induced calcium at outer mitochondrial membrane sub-region showed similar regulatory response to cytosolic calcium, not influenced by inhibition of mitochondrial calcium uniporter channel. Therefore, our work identified calcium flow pathways among extracellular medium, cell cytosol, and ER by regulatory calcium channels. Particularly, extracellular calcium flow has an essential function to fully activate ER calcium release.

China faces a persistent deficiency in feed protein resources. Enhancing the utilization efficiency of indigenous feed protein resources emerges as a viable strategy to alleviate the current deficit in protein feed supply. Corn gluten meal (CGM), characterized by high proportion of crude protein and glutamine, is predominantly employed in animal feed. Nonetheless, the water-insolubility of CGM protein hampers its protein bioavailability when utilized as feed material. This study aimed to augment protein bioavailability, liberate glutamine peptides from CGM, and produce gluta-mine-enriched CGM fermented feed. We executed a co-fermentation protocol using Bacillus subtilis A5, Lactobacillus 02002, and acid protease to generate the CGM fermented feed. Subsequent in vivo experiment with broilers were conducted to assess the efficacy of the fermented product. Findings revealed that the soluble protein, glutamine, small peptides, and lactic acid contents in the fer-mented feed increased by 69.1%, 700%, 47.6%, and 125.9%, respectively. Incorporating CGM fermented feed into the diet markedly enhanced the growth performance and intestinal health of broilers, positively modulated the cecal microbiota structure, and augmented the population of beneficial bacteria, specifically Lactobacillus. These results furnish both experimental and theoretical foundations for deploying CGM fermented feed as an alternative protein feed resource.

In an attempt to correct misunderstandings this article brings together the observations on Calcium, Myosin Binding Protein-C and Hypertrophic Cardiomyopathy in the basic function of cardiac muscle. A finding of many years ago is reiterated in a novel enzyme kinetic format with defined rate limiting step which makes CaATP the apparent substrate of the actomyosin cross-bridge. The relationship of these kinetics to recent observations on disruption of myosin binding protein-C is described along with how this bears on the understanding of the related cardiomyopathies.

Psychiatric disorders are mental, behavioral or emotional disorders. These conditions are prevalent, one in four adults suffer from any type of psychiatric disorders world-wide. It has always been observed that psychiatric disorders have a genetic component, however new methods to sequence full genomes of large cohorts have identified with high precision genetic risk loci for these conditions. Psychiatric disorders include, but are not limited to, bipolar disorder, schizophrenia, autism spectrum disorder, anxiety disorders, major depressive disorder, and attention-deficit and hyperactivity disorder. Several risk loci for psychiatric disorders fall within genes that encode for voltage-gated calcium channels (Ca_Vs). Calcium entering through Ca_Vs is key for multiple neuronal processes. In this review, we will summarize recent findings that link Ca_Vs and their auxiliary subunits to psychiatric disorders. First, we will provide a general overview of Ca_Vs structure, classification, function, expression and pharmacology. Next, we will summarize tools and databases to study risk loci associated with psychiatric disorders. We will examine functional studies of risk variations in Ca_V genes when available. We will review pharmacological evidence of the use of Ca_V modulators to treat psychiatric disorders. Our review will be of interest for those studying pathophysiological aspects of Ca_Vs.

This review critically examines the various ways in which the mechanical properties of wood have been understood. Despite the immense global importance of wood in construction, most understanding of its elastic and inelastic properties is based on models developed for other materials. Such models neglect wood’s cellular and fibrous nature. This review thus questions how well models that were originally developed for homogeneous and effectively continuous materials can describe wood’s mechanical properties. For example, the elastic moduli of wood have been found by many authors to depend on the size of the test specimen. Such observations are incompatible with classical elasticity theory. There is also much uncertainty about how well elastic moduli can be defined for wood. An analysis of different models for size effects of various inelastic properties of wood shows that these models only approximate the observed behaviour, and do not predict or explain the scatter in the results. A more complete understanding of wood’s mechanical properties must take account of it being in some sense intermediate between a material and a structure.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.

Background: Lipoprotein lipase (LPL) deficiency is a genetic condition. Affected individuals typically develop symptoms before age 10 with severe hypertriglyceridemia. No pharmacological treatment has lowered triglyceride levels in LPL deficiency patients successfully. The purpose of this study is to report on clinical outcomes of patients with LPL deficiency who responded to dietary therapy with successful reduction of their triglyceride (TG) levels with a long-chain triglyceride (LCT)-restricted, medium-chain triglyceride (MCT)-supplemented diet. Methods: A single-center retrospective case review study of LPL deficiency patients who met the inclusion criteria and were evaluated at the Hospital of Sick Children between January 2000 to December 2022. Data collected include demographic and clinical data, biochemical profiles at diagnosis and after dietary treatment initiation, and molecular results. Results: The study included seven patients with a suspected diagnosis of LPL deficiency (hypertriglyceridemia > 20 mmol/L). Six patients had a confirmed molecular diagnosis of LPL deficiency, and one had a Glycogen storage disease 1a (GSD1a) diagnosis. After presenting with hypertriglyceridemia, an LCT-restricted and MCT-supplemented diet was initiated, resulting in immediate and sustained TG reduction in all LPL deficiency patients that adhered to the diet. Additionally, they all maintained excellent growth and development. LPL deficiency-related complications were not observed under the MCT-enriched diet, except for increased pancreatic enzymes in one patient after dietary error. As expected, the diet failed to treat hypertriglyceridemia in the GSD1 patient. Conclusions: The dietary restriction of LCT in combination with MCT supplementation was feasible and effective in the long-term management of patients with LPL deficiency. In our experience, this treatment eliminated LPL-related complications and led to good clinical outcomes.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

This study investigates the utilization of innovative green composites made from hemp shiv, a waste by-product of hemp cultivation, with the aim of promoting sustainability within the construction industry. The manufacturing method involve the application of pressure in a mold to create the samples. These materials were produced using an environmentally friendly binder consisting of colophony, arabic gum and corn starch, moreover white glue and bioepoxy are also used to compare with the green resins. Three different binder compositions for the specimens. The samples underwent mechanical testing through tensile and bending assessments, and their performance was compared to that of non-green binders to validate the effectiveness of the manufacturing processes. The study revealed that decreasing the moisture content during the curing process is crucial for improving the mechanical properties. The best results were achieved when using arabic gum as a binder, yielding a tensile strength of 2.16 MPa and a bending strength of 5.25 MPa, with a composition of 62.5% hemp shiv and a manufacturing process involving a pressure of 5 MPa.

Management of calcium and phosphate in biofluids is key to maintaining physiological mineral homeostasis (i.e., appropriate mineralization of hard tissues and an absence of mineral deposition in soft tissues). This review describes and contrasts the ways vertebrates manage calcium phosphate in two biological fluids (breast milk and serum) and illustrates the benefits of mineral sequestration by proteins. In milk, phosphoprotein-sequestered calcium magnesium phosphates provide nutritional support, whereas in serum, protein-sequestered calcium phosphates control transport and delivery of calcium and phosphate to tissues for biological function or excretion. In addition, subsets of sequestered phosphates in serum have been identified as culprits underlying ectopic deposition of calcium phosphates and toxicity.

Pore Forming Toxins (PFTs), formed mainly by virulence factors of bacteria, belongs to Pore Forming Protein (PFP) family. Secreted as soluble monomers, they bind specific targets in membranes where their oligomerization and insertion place. Lysenin, a member of the PFTs, forms and oligomer after sphingomyelin binding, the so-called prepore, which become inserted forming a pore after a conformational change triggered by a pH decrease. In crowded conditions, oligomers tends to stay in prepore form because the prepore-to-pore transition is sterically blocked. In this study, we investigate the effect of calcium ions in those crowded conditions, finding that calcium act as a trigger for lysenin insertion. We localize the residues responsible for calcium sensitivity in a small α-helix. Our results are not only one of the few complete structural descriptions of prepore-to-pore transitions but the very first that involves a calcium triggering mechanism. The presence of glutamic or aspartic acids in the insertion domains could be an indication that calcium may be a general trigger for PFTs and more generally PFP.

We simulate elementary calcium release events (sparks) in a single calcium release unit in ventricular myocyte. Previously developed and tested electron-conformational model of the stochastic dynamics of RyR-channels is integrated to the calcium dynamics model in the cardiac cell. This approach allows to observe RyRs opening/closing in details on the macromolecular level during the calcium dynamics course. We simulate calcium diffusion in the dyadic space and “domino-like” RyR’s activation during the so-called “calcium induced-calcium release process”. Ca²⁺ sparks initiation, spread and termination are investigated in the computer experiments. Sparks’ initiation and termination rate dependence on the Ca²⁺ diffusion velocity is observed. We show that sarcoplasmic reticulum lumen local depletion and RyR’s stochastic attrition could be the reasons of Ca²⁺ spark termination.