Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

This paper addresses a method to transmit streaming data via rolling shutter camera-based optical camera communications (OCC). Since the amount of data that can be contained within one frame is limited, and the continuity of received data cannot be guaranteed due to OCC environmental variations, we introduce the concept of dividing the streaming data into several fragmented sets that are transmitted sequentially. We propose a superframe to contain sequential packets of fragmented data and corresponding indexes, so that sequential packets for streaming data can be continuously collected. When redundant frame transmission is considered, any packet lost due to OCC environmental conditions can be recovered. Experimental results show that the proposed method can be successfully used to transmit streaming data, with the number of redundant frames required to acquire all data packets based on image resolution. In addition, we describe how to identify missing packets from a network point of view to reduce the number of redundant frames needed to acquire all the data. This paper presents baseline results of communication performance when sending streaming data via a rolling shutter-based OCC.

Negative thermal quenching (NTQ) denotes that the integral emission spectral intensity of a given phosphor increases continuously with increasing temperature up to a certain elevated temperature. NTQ has been a subject of intensive investigation in recent years and a large number of phosphors were reportedly to have exhibited NTQ. In this paper, a collection of results in the archival literature about NTQ of specific phosphors are discussed from a macroscopic viewpoint in the following three aspects:1) Could NTQ of a given phosphor be reproducible?2) Could the associated data for a given phosphor exhibited NTQ be in line with the law of conservation of energy?3) Could NTQ of a given phosphor be demonstrated in a prototype WLED device? By analyzing typical cases based on common sense, it is hoped to increase the awareness for the issues with the papers reporting NTQ of the specific phosphors based on spectral intensity along with for the importance of keeping stability and consistency of the measurement conditions in temperature-dependent spectral intensity measurement which is a prerequisite for the validity of the measurement results.

Aim: To investigate the effects of intensive physical exercise on retinal microvascular regulation in healthy volunteers by the adaptive optics retinal camera measurement. Methods: We included healthy volunteers (11 men and 14 women) aged 20.6± 0.9. Heart rate (HR) and systolic and diastolic blood pressure (SBP, DBP) were recorded before and after a submaximal physical exertion of continuously riding a training ergometer. The superior temporal retinal artery measurements were captured using the adaptive optics (AO) camera rtx1TM (Imagine Eyes, Orsay, France) without pupil dilatation. We compared measures of vessel diameter (VD), lumen diameter (LD), two walls (Wall 1, 2), wall-to-lumen ratio (WLR), and wall cross-sectional analysis (WCSA) before and immediately after the cessation of exercise. Results: Cardiovascular parameters: After exercise, SBP, DBP and HR changed significantly from 130.2±13.2 to 159.7±15.6 mm Hg, 81.2±6.3 to 77.1±8.2 mm Hg and 80.8±16.1 to 175.0±6.2 bpm, respectively (p < 0.002). Retinal microcirculation analysis: Before the exercise, the mean LD was 96.0±6.8, VD 118.5±8.3, WLR 0.234±0.02, WCSA 3802.8±577.6. The mean LD and Wall 1 did not change significantly after exercise but slightly decreased. The VD, Wall 2, WLR and WCSA decreased significantly (p

Issues of fairness and consistency in Taekwondo poomsae evaluation have emerged owing to the lack of an objective evaluation method. This study proposes a three-dimensional (3D) convolutional neural network (CNN)-based action recognition model for the objective evaluation of Taekwondo poomsae. The model exhibits robust recognition performance regardless of variation in perspective by reducing the discrepancies between training and test images. The model uses 3D skeletons of the poomsae unit action collected using a full-body motion-capture suit to generate synthesized two-dimensional (2D) skeletons from the desired perspective. This approach aids in obtaining 2D skeletons from diverse perspectives as part of the training dataset and ensures consistent recognition performance regardless of the viewpoint. The model was trained using 2D skeletons projected from diverse viewpoints, and its performance was evaluated using various test datasets, including projected 2D skeletons and RGB images captured from various viewpoints. Comparison of the performance of the proposed model with that of previously reported action recognition models demonstrated the superiority of the model, underscoring its effectiveness in recognizing and classifying Taekwondo poomsae actions.

Previous camera self-calibration methods have exhibited certain notable shortcomings. On one hand, they either exclusively emphasized scene cues or solely focused on vehicle-related cues, resulting in a lack of adaptability to diverse scenarios and a limited number of effective features. Furthermore, these methods either solely utilized geometric features within traffic scenes or exclusively extracted semantic information, failing to comprehensively consider both aspects. This limited the comprehensive feature extraction from scenes, ultimately leading to a decrease in calibration accuracy. Additionally, conventional vanishing point-based self-calibration methods often required the design of additional edge-background models and manual parameter tuning, thereby increasing operational complexity and the potential for errors. Given these observed limitations, and in order to address these challenges, we propose an innovative roadside camera self-calibration model based on the Transformer architecture. This model possesses a unique capability to simultaneously learn scene features and vehicle features within traffic scenarios while considering both geometric and semantic information. Through this approach, our model can overcome the constraints of prior methods, enhancing calibration accuracy and robustness while reducing operational complexity and the potential for errors. Our method outperforms existing approaches on both real-world dataset scenarios and publicly available datasets, demonstrating the effectiveness of our approach.

The study of innovation in the public sector has attracted increasing interest in the last decade. Contributions of the literature concerning its possible innovation drivers and inhibitors have primarily had a theoretical or documentary perspective; empirical studies are scarce, as are work-team studies in organizations of this sector. The present study therefore focuses on identifying and understanding those variables or factors that induce or inhibit innovative activity in work teams in public organizations in a developing country. The research focus is qualitative, and 16 directors of 13 public Costa Rican institutions were interviewed for the study. A set of coding methods allowed to identify 19 thematic categories of variables linked to the capacity to generate innovations in these work teams.

Animal research has always been crucial for various medical and scientific breakthroughs, providing information on disease mechanisms, genetic predisposition to diseases, and pharmacological treatment. However, the use of animals in medical research is a source of great controversy and ongoing debate in modern science. To ensure a high level of bioethics, new guidelines have been adopted to replace animal testing wherever possible, reduce the number of animals per experiment, and refine procedures to minimize stress and pain. Supporting these guidelines, this article proposes a novel approach for unobtrusive, continuous, and automated monitoring of the respiratory rate of laboratory rats. It uses the cyclical expansion and contraction of the rats’ thorax/abdominal region to determine this physiological parameter. In contrast to previous work, the focus is on unconstrained animals, which requires the algorithms to be especially robust to motion artifacts. To test the feasibility of the proposed approach, video material of multiple rats was recorded and evaluated. High agreement was obtained between RGB-imaging and the reference method (respiratory rate derived from electrocardiography), which was reflected in a relative error of 5.46%. The current work shows that camera-based technologies are promising and relevant alternatives for monitoring the respiratory rate of unconstrained rats, contributing to the development of new alternatives for continuous and objective assessment of animal welfare and hereby guiding the way to modern and bioethical research.

Primate vision is an active process that constructs a stable internal representation of the 3D world based on 2D sensory inputs that are inherently unstable due to incessant eye movements. We present here a mathematical framework for processing visual information for a biologically-mediated active vision stereo system with asymmetric conformal cameras. This model utilizes the geometric analysis on the Riemann sphere developed in the group-theoretic framework of the conformal camera, thus far only applicable in modeling monocular vision. The asymmetric conformal camera model constructed here includes the fovea’s asymmetric displacement on the retina and the eye’s natural crystalline lens tilt and decentration, as observed in ophthalmological diagnostics. We extend the group-theoretic framework underlying the conformal camera to the stereo system with asymmetric conformal cameras. Our numerical simulation shows that the 1 theoretical horopter curves in this stereo system are conics that well approximate the empirical longitudinal horopters of the primate vision system.

Due to Motor Neurone Diseases, a large population remains disabled worldwide, negatively impacting their independence and quality of life. This typically involves a weakness in the hand and forearm muscles, making it difficult to perform fine motor tasks such as writing, buttoning a shirt, or gripping objects. This project presents a vision-enabled rehabilitation hand exoskeleton to assist disabled persons in their hand movements. The design goal was to create an accessible tool to help with a simple interface requiring no training. This prototype is built on a commercially available glove where a camera and embedded processor were integrated to help open and close the hand, using air pressure, thus grabbing an object. An accelerometer is also implemented to detect the characteristic hand gesture to release the object when desired. This passive vision-based control differs from active EMG-based designs as it does not require individualized training. Continuing the research will reduce the cost, weight, and power consumption to facilitate mass implementation.

The event camera generates an event stream based on changes in brightness, retaining only the characteristics of moving objects, addresses the high power consumption associated with using high-frame-rate cameras for high-speed eye tracking tasks. However, the asynchronous incremental nature of event camera output has not been fully utilized, and there are also issues related to missing event datasets. Combining the temporal information encoding and state-preserving properties of spiking neural network (SNN) with event camera, a near-range eye tracking algorithm is proposed as well as a novel event-based dataset for validation and evaluation. According to experimental results, the proposed solution outperforms artificial neural network (ANN) algorithms, while computational time remains only 12.5\% of that of traditional SNN algorithms. Furthermore, the proposed algorithm allows for self-adjustment of time resolution, with a maximum achievable resolution of 0.081ms, enhancing tracking stability while maintaining accuracy.

What drives an individual police officer to activate his body-worn camera (BWC)? Some evidence suggests officer attitudes and resistance to the technology contributes to the equivocal results in studies testing for BWCs effect on use-of-force, complaints, and other outcomes of interest. Leveraging a novel survey and administrative dataset, we investigate the predictors of BWC activation among 147 police officers in a single agency. With a test of three nested models, we find job function covariates offer robust predictive power of how often an officer activates her or his BWC. Neither demographic nor attitudinal measures significantly predict BWC activations, except for a negative relationship with how officers perceive BWC impacts on professional discretion. The study furnishes empirical support for understanding officers as Principled Agents: job function, guided by administrative policy is the most explanatory and parsimonious, while models of attitudes and demographics fail to improve upon the job function model.

: Since the COVID-19 pandemic, people have become aware that materials (products) can transmit infection and have begun to focus on questions such as how bacteria and germs, the sources of in-fection, maintain their infectivity on material surfaces, and the extent to which materials can or cannot prevent this. and to what extent materials can and cannot prevent it. The SIAA, a non-profit organization of many Japanese companies, had created an entirely separate interna-tional standard for materials' antibacterial, antiviral, and antibiofilm properties (products). The authors have studied the academic basis for the operation of the standards and were deeply in-volved as researchers in establishing one of the standards. This paper describes the interna-tional standards and some representative examples of the authors' actual use of these standards and explains the current status and future problems.

For public safety and physical security, currently more than a billion closed-circuit television (CCTV) cameras are deployed around the world. Proliferation of artificial intelligence (AI) and machine learning (ML) technologies has gained significant applications including crowd surveillance. The state-of-the-art distance and area estimation algorithms either need multiple cameras or a reference scale as a ground truth. It is an open question to obtain an estimation using a single camera without a scale reference. In this paper, we propose a novel solution called E-SEC, which estimates interpersonal distance between a pair of dynamic human objects, area occupied by a dynamic crowd, and density using a single edge camera. The E-SEC framework comprises edge CCTV cameras responsible for capture a crowd on video frames leveraging a customized YOLOv3 model for human detection. E-SEC contributes an interpersonal distance estimation algorithm vital for monitoring the social distancing of a crowd, and an area estimation algorithm for dynamically determining an area occupied by a crowd with changing size and position. A unified output module generates the crowd size, interpersonal distances, social distancing violations, area, and density per every frame. Experimental results validate the accuracy and efficiency of E-SEC with a range of different video datasets.

Low-cost RGB-D cameras are increasingly used in several research fields including human-machine interaction, safety, robotics, biomedical engineering and even Reverse Engineering applications. Among the plethora of commercial devices, the Intel RealSense cameras proved to be among the best suitable devices, providing a good compromise between cost, ease of use, compactness and precision. Released on the market in January 2018, the new Intel model RealSense D415 has a wide acquisition range (i.e. ~160-10000 mm) and a narrow field of view to capture objects in rapid motion. Given the unexplored potential of this new device, especially when used as a 3D scanner, the present work aims to characterize and to provide metrological considerations on the RealSense D415. In particular, tests are carried out to assess the device performances in the near range (i.e. 100-1000 mm). Characterization is performed by integrating the guidelines of the existing standard (i.e. the German VDI/VDE 2634 part 2 normative) with a number of literature-based strategies. Performance analysis is finally compared against latest close-range sensors, thus providing a useful guidance for researchers and practitioners aiming to use RGB-D cameras in Reverse Engineering applications.

Information cascades (tree-like structures formed by posts, comments, likes, replies, etc.) constitute the spine of the public online information environment, reflecting its various trends, evolving with it and, importantly, affecting its development. While users participate in online discussions, they display their views and thus contribute to the growth of cascades. At the same time, users’ opinions are influenced by cascades’ elements. The current paper aims to advance our knowledge regarding this social phenomenon by developing an agent-based model in which agents participate in a discussion around a post on the Internet. Agents display their opinions by writing comments on the post and liking them (i.e., leaving positive assessments). The result of these processes is dual: on the one hand, agents develop an information cascade; on the other hand, they update their views. Our purpose is to understand how agents’ activity, openness to influence, and cognitive constraints (that condition the amount of information individuals are able to proceed with) affect opinion dynamics. We also control for social contagions (when people’ perception of a message may depend not only on the message’s opinion, but also on how other individuals perceive this object, with more positive evaluations increasing the probability of adoption) and ranking algorithms that steer the order in which agents learn new messages. Among other things, we demonstrated that replies to disagreeable opinions are extremely effective for promoting your own position. In contrast, likes have a tiny effect on this issue.

This study emphasizes the necessity of introducing a blockchain-based joint logistics system to strengthen the competency of medical supply chain management (SCM) and tries to develop a healthcare supply chain management (HSCM) competency measurement item through an analytic hierarchy process. The variables needed for using blockchain-based joint logistics are the performance expectations, effort expectations, promotion conditions, and social impact of the UTAUT model, and the HSCM competency results in increased reliability and transparency, enhanced SCM, and enhanced scalability. Word cloud results, analyzing the most important considerations to realize work efficiency among medical industry-related agencies, mentioned numerous words, including sudden situations, delivery, technology trust, information sharing, effectiveness, urgency, etc. This might imply the need to establish a system that can respond immediately to emergency situations during holidays. It could also suggest the importance of real-time information sharing to increase the efficiency of inventory management. Therefore, there is a need of a business model that can increase the visibility of real-time medical SCM through big data analysis. By analyzing the importance of securing reliability based on the blockchain technology in the establishment of a supply chain network for HSCM competency, we reveal that joint logistics can be achieved and synergistic effects can be created by implementing the integrated database to secure HSCM competency. Strengthening partnerships, such as joint logistics, will eventually lead to HSCM competency. In particular, HSCM should seek ways to upgrade its competitive capabilities through big data analysis based on the establishment of a joint logistics system.

Human detection from Unmanned Aerial Vehicles (UAV) is gaining popularity in the field of disaster management, crowd counting, people monitoring. Real time human detection from UAV is a challenging task, because of many constraints involved. This study proposes a system for real time detection of humans on videos captured from UAVs addressing three of these constraints namely, flying height, computation time and scale of viewing. The proposed method integrated an android application with a binary classifier based on Haar-features to automatically detect human / non-human class from UAV images. The video frames were parsed and detected humans from image frames were geo-localized and visualized on Google Earth. The performance was evaluated for geo-localization accuracy, computation time and detection accuracy, considering human coverage – pixel size relationship for various heights and scale factor. Based on flying height - human size relationship and tradeoff between detection accuracy vs computation time, the study came up with optimal parameters for OpenCV’s cv2.cascadeClassifier. detectMultiScale function. This paper establishes a strong ground for further research relating to real time human detection from UAV.

Recent deep learning frameworks draw a strong research interest in the application of ego-motion estimation as they demonstrate a superior result compared to geometric approaches. However, due to the lack of multimodal datasets, most of these studies primarily focused on a single sensor-based estimation. To overcome this challenge, we collect a unique multimodal dataset named LboroAV2, using multiple sensors including camera, Light Detecting And Ranging (LiDAR), ultrasound, e-compass and rotary encoder. We also propose an end-to-end deep learning architecture for fusion of RGB images and LiDAR laser scan data for odometry application. The proposed method contains a convolutional encoder, a compressed representation and a recurrent neural network. Besides feature extraction and outlier rejection, the convolutional encoder produces a compressed representation which is used to visualise the network's learning process and to pass useful sequential information. The recurrent neural network uses this compressed sequential data to learn the relation between consecutive time steps. We use the LboroAV2 and KITTI VO datasets to experiment and evaluate our results. In addition to visualising the network's learning process, our approach gives superior results compared to other similar methods. The code for the proposed architecture is released in GitHub and accessible publicly.

Object-level Simultaneous Localization and Mapping (SLAM) has gained popularity in recent years since it can provide a means for intelligent robot-to-environment interactions. However, most of these methods assume that the distribution of the errors is gaussian. This assumption is not valid under many circumstances. Further, these methods use a delayed initialization of the objects in the map. During this delayed period, the solution relies on the motion model provided by an Inertial Measurement Unit (IMU). Unfortunately, the errors tend to accumulate quickly due to the dead-reckoning nature of these motion models. Finally, the current solutions depend on a set of salient features on the object’s surface and not the object’s shape. This research proposes an accurate object-level solution to the SLAM problem with a 4.1 to 13.1 cm error in the position (0.005 to 0.021 of the total path). The developed solution is based on Rao-blackwellized Particle Filtering (RBPF) that does not assume any predefined error distribution for the parameters. Further, the solution relies on the shape and thus can be used for objects that lack texture on their surface. Finally, the developed tightly coupled IMU/camera solution is based on an undelayed initialization of the objects in the map.

The use of motion capture has increased from last decade in a varied spectrum of applications like film special effects, controlling games and robots, rehabilitation system, animations etc. The current human motion capture techniques use markers, structured environment, and high resolution cameras in a dedicated environment. Because of rapid movement, elbow angle estimation is observed as the most difficult problem in human motion capture system. In this paper, we take elbow angle estimation as our research subject and propose a novel, markerless and cost-effective solution that uses RGB camera for estimating elbow angle in real time using part affinity field. We have recruited five (5) participants of (height, 168 ± 8 cm; mass, 61 ± 17 kg) to perform cup to mouth movement and at the same time measured the angle by both RGB camera and Microsoft Kinect. The experimental results illustrate that markerless and cost-effective RGB camera has a median RMS errors of 3.06° and 0.95° in sagittal and coronal plane respectively as compared to Microsoft Kinect.

Adherence is vital for medicine to have an effect, yet adherence is considered to be low. However, research into adherence tends to focus on quantitative analysis of performance, something which fails to perceive how people are adherent in their many different environments. As a contribution to gaining a deeper understanding, interviews were held with 30 individuals in UK, Egypt, Kazakhstan and 6 countries in sub-Saharan Africa to understand their perceptions on adherence for a range of drugs, and these were compared with an existing well-regarded list. New reasons for non-adherence were discovered, and a new viewpoint on adherence derived which considers adherence to be a single act and therefore as an individual opportunity to be adherent, permitting greater focus on the enablers and inhibitors of adherence at a point in time.

This paper is our attempt on the basis of physical theory to bring more clarification on the question ``What is life?'' formulated in the well-known book of Schr\"odinger in 1944. According to Schr\"odinger, the main distinguishing feature of biosystem's functioning is the ability to preserve its order structure or, in the mathematical terms, to prevent increasing of entropy. Since any biosystem is fundamentally open, it is natural to use open system's theory. However, Schr\"odinger's analysis shows that the classical theory is not able to adequately describe the order-stability in a biosystem. Schr\"odinger should also appeal to the ambiguous notion of negative entropy. We suggest to apply the quantum theory. As is well-known, behaviour of the quantum von Neumann entropy crucially differs from behaviour of the classical entropy. We consider a complex biosystem $S$ composed of many subsystems, say proteins, or cells, or neural networks in the brain, i.e., $S=(S_i).$ We study the following problem: if the composed system $S$ can preserve the ``global order'' in the situation of increase of local disorder and if $S$ can preserve its entropy while some of $S_i$ increase their entropies We show that within quantum information theory the answer is positive. The significant role plays entanglement of the subsystems states. In the absence of entanglement, increasing of local disorder generates disorder increasing in the compound system $S$ (as in the classical regime).

Abstract: In complex revision total hip arthroplasties, careful preoperative planning is crucial for the proper reconstruction of hip biomechanics. With conventional 2D radiographic images and computed tomography (CT) the 3D extension of the defect and the remaining bone stock may not be evaluated properly. 3D printed models can aid the surgeon in planning complex acetabular re-construction. The purpose of this study is to compare the accuracy of bony defect assessment in severe acetabular defects surgery with 3D printing planning as compared to conventional 2D ra-diographic planning and CT. Twenty-five patients with severe acetabular defects (Paprosky IIC and III) undergoing revision surgery were enrolled. Each patient had a 3D printed model of their femur and pelvis created based on CT scans. Clinical and radiographic assessments were conducted before and after surgery, with four key bone landmarks measured and compared between X-ray, CT, 3D models, and surgical reports. The findings revealed discrepancies in defect assessment between different imaging methods. X-rays and CT scans sometimes incorrectly identified affected areas, while the 3D models showed more accurate results. This study suggests that 3D printed models can significantly improve the preoperative evaluation of complex hip arthroplasty revisions, enabling surgeons to better select optimal surgical strategies.

Smartphone-based fundus camera and telemedicine are an opportunity for accessing ocular health inequalities in underresourced areas. The objective of this study is to evaluate the prevalence of retinal findings in a community in the Amazon and propose strategies to enhance ocular health. A cross-sectional study was conducted in a river side community. Retinal photos from the posterior pole and optic disc were captured using a portable fundus camera. All photos and data were analyzed remotely by a retina specialist. The final sample was 107 participants, aged 52±17. Retinal findings were detected in 37.4% (95%CI 28.7–46.8) of the sample, the three main retinal findings were epithelial changes (10.3%, 95%CI 5.6–17.1), chorioretinal scars (8.4%, 95%CI 4.2–14.8), and dry Age-related Macular Degeneration (7.5%, 95%CI 3.6–13.6). This study detected retinal alterations in similar prevalence of other underresourced areas. Telemedicine is an opportunity to address health inequities, especially in ophthalmology, through relatively low-cost portable devices, supporting clinical decisions in areas with low health access, however, maintaining assistance after implementation is a challenge. Enhancing medical education and training local non-specialized health professionals for risk assessment, device handling, and data base use is reasonable to ensure follow-up.

Optical wireless communication is a promising emerging technology that addresses the limitations of radio-frequency-based wireless technologies. This study presents a novel hybrid modulation for optical camera communication (OCC); it integrates two waveforms transmitted from a single transmitter light-emitting diode (LED) and received by two rolling-shutter camera devices. Then, a smart camera with a high-resolution image sensor captures the high-frequency signal, and a low-resolution image sensor from a smartphone camera captures the low-frequency signal. Through this hybrid scheme, two data streams are transmitted from a single LED lamp; this reduces the cost of the indoor OCC device compared to one that transmits two signals from two different LEDs. In proposed scheme, rolling-shutter orthogonal frequency-division multiplexing is used for the high-frequency signals, and M-ary frequency-shift keying is used for the low-frequency signals in the time domain. This proposed scheme is compatible with smart phone camera and USB camera. By controlling the OCC parameters, the hybrid scheme can be implemented with high performance for a communication distance of 10 m.

Given a stream of depth images with a known cuboid reference object present in the scene, we propose a novel approach for accurate camera tracking and volumetric surface reconstruction in real-time. Our contribution in this paper is threefold: (a) utilizing a priori knowledge of the cuboid reference object, we keep drift-free camera tracking without explicit global optimization; (b) we improve the fineness of the volumetric surface representation by proposing a prediction-corrected data fusion strategy rather than simple moving average, which enables accurate reconstruction of high-frequency details such as sharp edges of objects and geometries of high curvature; (c) we introduce a benchmark dataset CU3D containing both synthetic and real-world scanning sequences with ground-truth camera trajectories and surface models for quantitative evaluation of 3D reconstruction algorithms. We test our algorithm on our dataset and demonstrate its accuracy compared with other state-of-the-art algorithms. We release both our dataset and code as opensource1 for other researchers to reproduce and verify our results.

Instead of tissue-based detection, blood-based tumor mutation burden (bTMB) is becoming an alternative promising alternate to predict the response of immune checkpoint inhibitor in cancers, especially non-small-cell lung cancer. Although bTMB is more convenient and less invasive, many evidences identified its limited predictive ability and less accurate discrimination of candidates to receive immunotherapy. Several ways of adjustments have been applied to improve the clinical usefulness of bTMB, such as setting restriction for threshold of allele frequency to exclude some unwanted mutations. But many questions remained to be explored such as the number and the type of mutations that should be incorporated into the bTMB estimation. This viewpoint summarized the current attempts to modify bTMB and provided granular aspects that have implications for further enhancement of bTMB’s predictive capability.

The impact of metals bioaccumulation on marine organisms is under investigation. This study was designed to determine the association of oxidative stress in mussels Mytilus galloprovincialis induced by seawater enriched with trace metals with protein synthesis. Mussels were exposed to 40 μg/L Cu, 30 μg/L Hg, or 100 μg/L Cd for 5 and 15 days, and the pollution effect was evaluated by measuring established oxidative biomarkers. The results showed damage on the protein synthesis machine integrity and specifically, on translation factors and ribosomal proteins expression and modifications. Exposure of mussels to all metals caused oxidative damage that was milder in the cases of Cu and Hg, and more pronounced for Cd. However, after prolonged exposure of mussels to Cd (15 days), the effects receded. These changes that perturb protein biosynthesis can serve as a great tool for elucidating the mechanisms of toxicity and could be integrated in biomonitoring programs.

Although the field of geomatics has seen multiple technological advances in the recent years which enabled new applications and simplified the consolidated ones, some tasks remain challenging, inefficient, and time- and cost-consuming. This is the case of accurate tridimensional surveys of narrow spaces. Static laser scanning is an accurate and reliable approach but impractical for extensive tunnel environments; portable laser scanning is on the other hand time-effective and efficient but not very reliable without ground control constraints. This paper describes the development process of a novel image-based multi-camera system meant to solve this specific problem: delivering accurate, reliable, and efficient results. The development is illustrated from the system conceptualization and initial investigations to the design choices and requirements for accuracy. The resulted working prototype has been put to the test to verify effectiveness of the proposed approach.

In the field of forensic imaging, it is important to be able to extract a “camera fingerprint” from one or a small set of images known to have been taken by the same camera (image sensor). Ideally, that fingerprint would be used to identify an individual source camera. Camera fingerprint is based on certain kind of random noise present in all image sensors that is due to manufacturing imperfections and thus unique and impossible to avoid. PRNU (Photo-Response Non-Uniformity) has become the most widely used method for SCI (Source Camera Identification). In this paper, we design a set of “attacks” to a PRNU based SCI system and we measure the success of each method. We understand an attack method as any processing that alters minimally image quality and that is designed to fool PRNU detectors (or, generalizing, any camera fingerprint detector). The PRNU based SCI system was taken from an outstanding reference that is publicly available.

Fluorescence microscopy provides an unparalleled tool for imaging biological samples. However, producing high-quality volumetric images quickly and without excessive complexity remains a challenge. Here, we demonstrate a simple multi-camera structured illumination microscope (SIM) capable of simultaneously imaging multiple focal planes, allowing for the capture of 3D fluorescent images without any axial movement of the sample. This simple setup allows for the acquisition of many different 3D imaging modes, including 3D time lapses, high-axial-resolution 3D images, and large 3D mosaics.

A lensless camera is an ultra-thin computational-imaging system. Existing lensless cameras are based on the axial arrangement of an image sensor and a coding mask, and therefore, the back side of the image sensor cannot be captured. In this paper, we propose a lensless camera with a novel design that can capture the front and back sides simultaneously. The proposed camera is composed of multiple coded image sensors, which are complementary-metal-oxide-semiconductor~(CMOS) image sensors in which air holes are randomly made at some pixels by drilling processing. When the sensors are placed facing each other, the object-side sensor works as a coding mask and the other works as a sparsified image sensor. The captured image is a sparse coded image, which can be decoded computationally by using compressive-sensing-based image reconstruction. We verified the feasibility of the proposed lensless camera by simulations and experiments. The proposed thin lensless camera realizes super field-of-view imaging without lenses or coding masks, and therefore can be used for rich information sensing in confined spaces. This work also suggests a new direction in the design of CMOS image sensors in the era of computational imaging.

This paper presents an approach to teacher identity heritage as result of the implementation of a research device created through Arts-based Research (ABR) methods, specifically with video elicitation and video essay used as research tools. Two main objectives were raised. The first one, to establish the real relevance of focusing performance on teacher identity. The second one, testing a new methodological proposal specifically designed for this purpose, but still useful in other contexts where heritage identity is as present as in teaching. The device, Body-camera, involves a process that allows new ways to understand the creation of identities using video to encourage the production of new meanings by visual and oral data. The participants were teachers in training during their internship period. Some notions about teachers' identity heritage were revealed, and also preserved, firstly, through personal perspectives by video elicitations and secondly, through collective perspectives by video essays. Both are video structures used in ABR which mix creative experience, memories, life experiences, relationships and links that shape the teachers’ professional identity.

India ranks among the top ten nations in the world for grape production. Fungal pathogens inflict damage to crop plants in turn making cultivators bear huge economical losses. With an output of 1.21 million tons (about 2% of 57.40 million tons produced globally). 1.2% of the nation’s total fruit cropland is covered by grapes. But due to fungal diseases the effect of the yield produced ranges from 5-80% depending on the severity of diseases which will affect the yield of grape vineyard. In precision agriculture, new sensing technologies and artificial intelligence could be used to automatically identify grapevine and disease pest symptoms. Traditional manual disease-monitoring methods are inefficient, labor-intensive, and ineffective. Timely effective and precise evaluation of grape diseases is admitted as a critical step in the field management. In this paper, we are explaining about different optical sensing methods applied for RGB, Multispectral and Thermal cameras. Section-wise we will be describing environmental set up for image-aquation, data-preprocessing, different modelling methods, evaluation matrix, result, and reviewer’s comment.

Traditional camera sensors rely on human eyes for observation. However, the human eye 1 is prone to fatigue when observing targets of different sizes for a long time in complex scenes, and 2 human cognition is limited, which often leads to judgment errors and greatly reduces the efficiency. 3 Target recognition technology is an important technology to judge the target category in camera 4 sensor. In order to solve this problem, a small size target detection algorithm for special scenarios was 5 proposed by this paper. Its advantage is that this algorithm not only has higher precision for small 6 size target detection, but also can ensure that the detection accuracy of each size is not lower than the 7 existing algorithm. In this paper, a new down-sampling method was proposed, which could better 8 preserve the context feature information. The feature fusion network was improved to effectively 9 combine shallow information and deep information. A new network structure was proposed to 10 effectively improve the detection accuracy of the model. In terms of accuracy, it is better than: YOLOX, 11 YOLOXR, YOLOv3, scaled YOLOv5, YOLOv7-Tiny and YOLOv8.Three authoritative public data sets 12 were used in this experiment: a) On Visdron data sets (small size targets), DC-YOLOv8 is 2.5% more 13 accurate than YOLOv8. b) On Tinyperson data sets (minimal size targets), DC-YOLOv8 is 1% more 14 accurate than YOLOv8. c) On PASCAL VOC2007 data sets (Normal size target), DC-YOLOv8 is 0.5% 15 more accurate than YOLOv8.

The determination of crack propagation velocities can provide valuable information for a better understanding of damage processes of concrete. The spatio-temporal analysis of crack patterns developing at a speed of several hundred meters per second is a rather challenging task. In the paper, a photogrammetric procedure for the determination of crack propagation velocities in concrete specimens using high-speed camera image sequences is presented. A cascaded image sequence processing which starts with the computation of displacement vector fields for a dense pattern of points on the specimen’s surface between consecutive time steps of the image sequence chain has been developed. These surface points are triangulated into a mesh, and as representations of cracks, discontinuities in the displacement vector fields are found by a deformation analysis applied to all triangles of the mesh. Connected components of the deformed triangles are computed using region-growing techniques. Then, the crack tips are determined using principal component analysis. The tips are tracked in the image sequence and the velocities between the time stamps of the images are derived. A major advantage of this method as compared to established techniques is in the fact of its allowing for spatio-temporally resolved, full-field measurements rather than point-wise measurements and that information on crack width can be obtained simultaneously. To validate the experimentation, the authors processed image sequences of tests on four compact-tension specimens performed on a split-Hopkinson tension bar. The images were taken by a high-speed camera at a frame rate of 160,000 images per second. By applying to these datasets the image sequence processing procedure as developed, crack propagation velocities of about 800 m/s were determined with a precision in the order of 50 m/s.

Parallax processing and structure preservation has long been important and challenging tasks in image stitching. In this paper, an image stitching method based on sliding camera to eliminate perspective deformation and asymmetric optical flow to solve parallax is proposed. By maintaining the viewpoint of two input images in the mosaic non-overlapping area and creating a virtual camera by interpolation in the overlapping area, the viewpoint is gradually transformed from one to another image view-point so as to complete the smooth transition of the two image viewpoints and reduce perspective deformation. Two coarsely aligned warped images are generated with the help of a global projection plane. After that, the optical flow propagation and gradient descent method are used to quickly calculate the bidirectional asymmetric optical flow between the two warped images, and the optical flow-based method is used to further align the two warped images to reduce parallax. In the image blending, the softmax function and registration error are used to adjust the width of the blending area, further eliminating ghosting and reduce parallax. Finally, the comparative experiments show that our method can effectively eliminate perspective deformation, reduce misalignment, and save running time.

The COVID-19 outbreak demonstrated the viability of various remote working solutions, telepresence robots (TPRs) being one of them. High-quality video transmission is one of the cornerstones of using such solutions, as most of the information about the environment is acquired through vision. This study aims to compare the camera capabilities of four models of popular telepresence robots using compact reduced LogMAR and Snellen optometry charts as well as text displayed on the projector screen. The symbols from the images are extracted using OCR (Optical Character Recognition) software and the results of the recognition are compared with the symbols on the charts. Double 3 TPR provides the best quality images of optometric charts, but the OCR results of measurements of the image on the projector do not show the clear advantage of one single model over the others. The results demonstrated by Temi 2 and Double 3 TPRs are generally better than the others, suggesting that these TPRs are more feasible to be used in teaching and learning scenarios.

This paper presents a novel dynamic camera parameter control method for position and posture estimation of highly miniaturized AR markers (micro AR markers) using a low cost general camera. The proposed method performs iterative calculation of the marker’s position and posture to converge them to specified accuracy with dynamically updating the camera’s zoom, focus and other parameter values based on the detected marker’s depth distances. For a 10 mm square micro AR marker, the proposed system demonstrated recognition accuracy of better than ±1.0% for depth distance and 2.5∘ for posture angle with a maximum recognition range of 1.0 m. In addition, the iterative calculation time was at most 0.7 seconds in an initial detection of the marker. These experimental results suggest that the proposed method and system can be applied to a robotic precise handling of small objects with low cost.

As part of the Earth Climate Observatory space mission concept for the direct observation from space of the Earth Energy Imbalance, we propose an advanced camera suite for the high resolution observation of the Total Outgoing Radiation of the Earth. For the observation of the Reflected Solar Radiation, we propose the use of two multispectral cameras covering the range from 400 to 950 nm, with a nadir resolution of 1.7 km, combined with a high resolution RGB camera, with a nadir resolution of 0.57 km. For the observation of the Outgoing Longwave Radiation, we propose the use of 6 microbolometer cameras, with each a spectral bandwidth of 1 μm in the range from 8 to 14 μm, and with a nadir resolution of 2.2 km.

This paper presents the robotic platform, PiBot, that has been developed and that is aimed at improving the teaching of Robotics with vision to secondary students. Its computational core is the Raspberry Pi 3 controller board, and the greatest novelty of this prototype is the support developed for the powerful camera mounted on board, the PiCamera. An open software infrastructure written in Python language was implemented so that the student may use this camera, or even a WebCam, as the main sensor of this robotic platform. Also, higher level commands have been provided to enhance the learning outcome for beginners. In addition, a PiBot 3D printable model and the counterpart for the Gazebo simulator were also developed and fully supported. They are publicly available so that students and educational centers that do not have the physical robot or can not afford the costs of these, can nevertheless practice and learn or teach Robotics using these open platforms: DIY-PiBot and/or simulated-PiBot.

UV SO₂ cameras have become a common tool to measure and monitor SO₂-emission-rates, mostly from volcanoes but also from anthropogenic sources (e.g. power plants or ships). In the past years, the analysis of UV SO₂ camera data has seen many improvements. As a result, for many of the required analysis steps, several alternatives exist today. This inspired the development of Pyplis, an open-source software toolbox written in Python 2.7, which aims to unify the most prevalent methods from literature within a single, cross-platform analysis framework. Pyplis comprises a vast collection of algorithms relevant for the analysis of UV SO₂ camera data. These include several routines to retrieve plume background radiances as well as routines for cell and DOAS based camera calibration. The latter includes two independent methods to identify the DOAS field-of-view within the camera images. Plume velocities can be retrieved using an optical flow algorithm as well as signal cross-correlation. Furthermore, Pyplis includes a routine to perform a first order correction of the signal dilution effect. All required geometrical calculations are performed within a 3D model environment allowing for distance retrievals to plume and local terrain features on a pixel basis. SO₂-emission-rates can be retrieved simultaneously for an arbitrary number of plume intersections. Pyplis has been extensively and successfully tested using data from several field campaigns. Here, the main features are introduced using a dataset obtained at Mt. Etna, Italy on 16 September 2015.

In this paper, an intelligent blind guide system based on 2D LiDAR and RGB-D camera sensing is proposed, and the system is mounted on the smart cane. The intelligent guide system relies on 2D LiDAR, RGB-D camera, IMU, GPS, Jetson nano B01, STM32 and other hardware. The main advantage of the intelligent guide system proposed by us is that the distance between the smart cane and obstacles can be measured by 2D LiDAR based on Cartographer algorithm, thus achieving Simultaneous localization and mapping (SLAM). At the same time, through the improved yolov5 algorithm, pedestrians, vehicles, pedestrian crosswalks, traffic lights, warning posts, stone piers, tactile paving and other objects in front of the visually impaired can be quickly and effectively identified. Laser SLAM and improved yolov5 obstacle identification tests were carried out inside a teaching building on the campus of Hainan Normal University and on a pedestrian crossing on Longkun South Road in Haikou City, Hainan Province. The results show that the intelligent guide system developed by us can drive the wheels and omnidirectional wheels at the bottom of the smart cane, and give the smart cane a self-leading blind guide function like a "guide dog", which can effectively guide the visually impaired to avoid obstacles and reach the predetermined destination, and can quickly and effectively identify the obstacles on the way out. The laser SLAM speed of this system is 25~31FPS, which can realize the short-distance obstacle avoidance and navigation function both in indoor and outdoor envionments. The improved yolov5 helps to identify 86 types of objects, the recognition rate for pedestrian crosswalks and for vehicles are 84.6% and 71.8%, respectively; the overall recognition rate for 86 types of objects is 61.2%, and the obstacle recognition rate of the intelligent guide system is 25-26FPS.

Aquifer karstic structures, due to their complex nature, present significant challenges in accurately mapping their intricate features. Traditional methods often rely on invasive techniques or sophisticated equipment, limiting accessibility and feasibility. In this paper, we propose a new approach to non-invasive, low-cost 3D reconstruction using a camera that observes the light projection of a simple diving lamp. Our method capitalizes on the principles of structured light, leveraging the projection of light contours onto the karstic surfaces. By capturing the resultant light patterns with a camera, we reconstruct three-dimensional representations of the structures. The simplicity and portability of the equipment required make this method highly versatile, enabling deployment in diverse underwater environments. We validate our approach through extensive field experiments conducted in various aquifer karstic settings. The results demonstrate the efficacy of our method in accurately delineating intricate karstic features with remarkable detail and resolution. Furthermore, the non-destructive nature of this technique minimizes disturbance to delicate aquatic ecosystems while providing valuable insights into the subterranean landscape. This innovative methodology not only offers a cost-effective and non-invasive means of mapping aquifer karstic structures but also opens avenues for comprehensive environmental monitoring and resource management. Its potential applications span hydrogeological studies, environmental conservation efforts, and sustainable water resource management in karstic terrains worldwide.

3D-mapping-aided (3DMA) global navigation satellite system (GNSS) positioning that improves positioning performance in dense urban areas has been under development in the recent years, but it still faces many challenges. This paper details a new algorithm that explores the potential of using building boundary for positioning. Rather than applying complex simulations to analyze and correct signal reflections by buildings, the approach utilizes a convolutional neural network to differentiate between the sky and building in a sky-pointing fisheye image. A new skymask matching algorithm is then proposed to match the segmented fisheye images with skymasks generated from a 3D building model. Each matched skymask holds a latitude and longitude coordinate to determine the precise location of the fisheye image. The results are then compared with the conventional GNSS and advanced 3DMA GNSS positioning methods. The aims of the proposed algorithm are to increase positioning and heading accuracy in a rich urban environment.

In a previous paper (https://dx.doi.org/10.2139/ssrn.3648127 ), an elementary and thoroughly arithmetical proof of Fermat’s last theorem by induction has been demonstrated if the case for “n = 3” is granted as proved only arithmetically (which is a fact a long time ago), furthermore in a way accessible to Fermat himself though without being absolutely and precisely correct. The present paper elucidates the contemporary mathematical background, from which an inductive proof of FLT can be inferred since its proof for the case for “n = 3” has been known for a long time. It needs “Hilbert mathematics”, which is inherently complete unlike the usual “Gödel mathematics”, and based on “Hilbert arithmetic” to generalize Peano arithmetic in a way to unify it with the qubit Hilbert space of quantum information. An “epoché to infinity” (similar to Husserl’s “epoché to reality”) is necessary to map Hilbert arithmetic into Peano arithmetic in order to be relevant to Fermat’s age. Furthermore, the two linked semigroups originating from addition and multiplication and from the Peano axioms in the final analysis can be postulated algebraically as independent of each other in a “Hamilton” modification of arithmetic supposedly equivalent to Peano arithmetic. The inductive proof of FLT can be deduced absolutely precisely in that Hamilton arithmetic and the pransfered as a corollary in the standard Peano arithmetic furthermore in a way accessible in Fermat’s epoch and thus, to himself in principle. A future, second part of the paper is outlined, getting directed to an eventual proof of the case “n=3” based on the qubit Hilbert space and the Kochen-Specker theorem inferable from it.

Ultrasound A-scan is an important tool for quantitative assessment of ocular lesions. However, its usability is limited by difficulty to accurately localize the ultrasound probe to a lesion of interest. In this study, a transparent LiNbO3 single crystal ultrasound transducer was fabricated, and integrated with a widefield fundus camera to guide the ultrasound local position. The novel fundus camera guided ultrasound probe was validated for in vivo measurement of rat eyes. Anterior and posterior segments of the rat eye could be unambiguously differentiated with the fundus photography guided ultrasound measurement. A model eye was also used to verify the clinical potential of the prototype device.

Four-polarisation camera was used to map absorbance of olivine micro-grains before and after high temperature annealing (HTA). It is shown that HTA of olivine xenolith at above 1200∘C in O2 flow makes it magnetised. Different mode of operation of polariscope with polarisation control before and after the sample in transmission and reflection modes was used. The reflection type was assembled for non-transparent samples of olivine after HTA. Sample for optical observation in transmission was placed on an achromatic plastic quarter-wavelength waveplate as a sample holder. Inspection for sample’s birefringence (retardance) as well as absorbance can be made. A best fit of transmitted intensity or transmittance T (hence absorbance A=−log10T) becomes accessible by simple best-fit using only three orientations (from measured four orientations by the camera). When intensity of transmitted light at one of the orientations was very low due to cross-polarised condition (polariser-analyser arrangement), the three-points fit can be used. Three-point fit in transmission and reflection modes was validated for T(θ)=Amp×cos(2θ−2θshift)+offset, where amplitude Amp, offset offset and orientation azimuth θshift are extracted for each pixel via the best fit.

Tropical rock lobsters (Panulirus ornatus) are a highly cannibalistic species with intermoult animals predominantly attacking animals during ecdysis (moulting). Rapid, positive characterisation of pre-ecdysis lobsters may open a pathway to disrupt cannibalism. Ecdysial suture line development is considered for pre-ecdysis recognition with suture line definition compared for lobsters emerged and immerged, using white, near ultraviolet (365 nm), near infrared (850 nm) and spe-cialty Osram SFH 4737 broadband IR LEDs against a reference of intermoult lobsters with no suture line development. An alternative pre-ecdysis recognition strategy used a novel low-cost spectral camera composed of the Sony IMX219, AMS AS7265x spectral sensors and Osram SFH 4737 broadband infrared LEDs. Images and data using the novel low-cost spectral camera was acquired from intermoult, pre-ecdysis, and post-ecdysis lobsters. Compared with the white light appear-ance, suture line definition was enhanced under 850 nm, 365 nm, and SFH 4737 LEDs for immerged lobsters, while the 850 nm LED achieved the best suture line definition of emerged lobsters. The spectral camera was unable to characterise pre-ecdysis. A least squares regression for binary classification decision boundary successfully separated 86.7% of post-moult lobsters. Achieving post-moult characterisation validated the speculative exploratory approach in developing this novel low-cost spectroscopy tool.

A free-fall baited camera lander was launched for the first time on the Cosmonaut Sea shelf of East Antarctica at the depth of 694 m during the 38th Chinese National Antarctic Research Expedition (CHINARE) in 2022. We identified 31 unique taxa (23 of invertebrates and 8 of fishes) belonging to 8 phyla from 2403 pictures and 40 videos. The Antarctic jonasfish (Notolepis coatsi) was the most frequently observed fish taxa. Ten species of vulnerable marine ecosystem (VME) taxa were observed, accounting for 32% of all species. The maximum number (MaxN) of Natatolana meridionalis individuals per image frame was ten, and they were attracted to the bait. The macrobenthic community type was sessile suspension feeders with associated fauna (SSFA), which was shaped by the muddy substrata with scattered rocks. Rocks served as the best habitats for sessile fauna. The study reveals the megafauna community and their habitat by image survey in the Cosmonaut Sea for the first time. It helped us obtain Antarctic biodiversity baselines and monitoring data for future’s ecosystem health assessment and better protection.

NUSES is a pathfinder satellite project hosting two detectors: Terzina dedicated to the study of ultra-high-energy cosmic rays (UHECRs) above 100 PeV and Zirè focused on the study of protons and electrons below 250 MeV and MeV gamma rays. This work concerns mainly the description of the Cherenkov camera, composed of SiPMs, for the Terzina telescope. Cherenkov light produced by extensive air showers induced by Ultra High Energy Cosmic Rays in the atmosphere could be detected from space, thus ensuring huge exposures. The Terzina telescope is being designed to detect such light. It has an effective area of about 0.1 m2 and an equivalent focal length of about 930 mm with a diameter of the circle containing 80% of the photons of less than 1 mm2. The photo-detection plane is composed of 2×5 SiPM arrays with 8×8 channels of 3×3 mm2 pixels each. To increase the data-taking period NUSES orbit will be sun-synchronous (with a height of about 550 km), thus allowing Terzina to point always towards the dark side of the Earth’s limb. The sun-synchronous orbit requires small distances to the poles, and as a consequence the expected dose received by the SiPMs will be 10 Gy during three year of NUSES mission. About 70% of the integral dose is delivered by the electrons and secondary gammas created in the mechanical structure and about 30% from protons. This estimation is done with the Geant4 simulation of the preliminary telescope geometry, without taking into account solar wind protons. We study the SiPM photo sensors under the irradiation received by the 50 MeV protons up to 30 Gy of total integrated dose corresponding to 9 years of the satellite operation.

This paper introduces a novel approach to addressing the challenge of accurately timing short distance runs, a critical aspect in the assessment of athletic performance. Electronic photoelectric barriers, although recognized for their dependability and accuracy, have remained largely inaccessible to non-professional athletes and smaller sport clubs due to their high costs. A comprehensive review of existing timing systems reveals that claimed accuracies beyond 30 milliseconds lack experimental validation across most available systems.To bridge this gap, a mobile, camera-based timing system is proposed, capitalizing on consumer-grade electronics and smartphones to provide an affordable and easily accessible alternative. By leveraging readily available hardware components, the construction of the proposed system is detailed, ensuring its cost-effectiveness and simplicity. Experiments involving track and field athletes demonstrate the proficiency of the proposed system in accurately timing short distance sprints. Comparative assessments against a professional photoelectric cells timing system reveal a remarkable accuracy of 62 milliseconds, firmly establishing the reliability and effectiveness of the proposed system. This finding places the camera-based approach on par with existing commercial systems, thereby offering non-professional athletes and smaller sport clubs an affordable means to achieve accurate timing.In an effort to foster further research and development, open access to the device's schematics and software is provided. This accessibility encourages collaboration and innovation in the pursuit of enhanced performance assessment tools for athletes.

Owing to the advantages of cost-effectiveness, compactness, and the avoidance of complicated camera synchronization, single-camera three-dimensional (3D) digital image correlation (DIC) techniques have gained increasing attention for deformation measurement of materials and structures. In the traditional single-camera 3D-DIC system, the left and right view images can be recorded by a single camera using a diffraction grating, a bi-prism or a set of planar mirrors. To further improve the measurement accuracy of single-camera 3D-DIC, this paper introduces a single-camera four-view imaging technique by installing a pyramidal prism in front of the camera. The 3D reconstruction of the measured points before and after deformation is realized with eight governing equations induced by four views, and the strong geometric constraints of four views can help to improve the measurement accuracy. A static experiment, a rigid body translation experiment and a four-point bending experiment show that the proposed single-camera 3D-DIC method can achieve higher measurement accuracy than the dual-view single-camera 3D-DIC techniques and has advantages in reducing both random error and systematic error.

Tumor necrosis factor (TNF) is a pleiotropic cytokine regulating many physiological and pathological immune-mediated processes. Although initially described as a tumor-cytotoxic agent, over time, it has also been recognized as an essential pro-inflammatory cytokine implicated in the pathogenesis of different autoimmune diseases, such as multiple sclerosis (MS). Several studies have shown an increase in TNF expression both in acute and chronic active MS brain lesions, as well as its involvement in maintaining a chronic inflammatory intrathecal process known as “compartmentalized inflammation”, which contributes to disease progression and disability accumulation in MS, even more than acute inflammatory activity. Indeed, high TNF levels were observed in the serum and cerebrospinal fluid of subjects with MS and correlated to disease severity, promoting axonal damage and, consequently, neurodegeneration. In this review we discuss the current knowledge of TNF and its receptors involvement in MS progression, focusing on disability progression independent of relapse activity (PIRA), meant as the disability accumulation evident in relapsing MS patients not related to acute inflammatory events.

(1) Background: The imaging energy range of a typical Compton camera is limited due to the fact that scattered gamma photons are seldom fully absorbed when the incident energies are above 3 MeV. Further improving the upper energy limit of gamma-ray imaging has important application significance in active interrogation of special nuclear materials and chemical warfare agents, as well as range verification of proton therapy; (2) Methods: To realize gamma-ray imag-ing in a wide energy range of 0.3~7 MeV, a principle prototype, named a portable three-layer Compton camera, was developed using the scintillation detector that consist of an silicon photo-multiplier array coupled with a Gd3Al2Ga3O12:Ce pixelated scintillator array. Implemented in a list-mode maximum likelihood expectation maximization algorithm, a far-field energy-domain imaging method based on two-interaction and three-interaction events was applied to estimate the initial energy and spatial distribution of gamma-ray sources. The simulation model of detec-tors was established based on Monte Carlo simulation toolkit Geant4. The reconstructed images of a 133Ba, a 137Cs and a 60Co point-like sources were successfully obtained with our prototype in laboratory tests and compared with simulation studies; (3) Results: The proportion of effective imaging events accounted for about 2%, which made our prototype realize reconstructing the distribution of a 0.05 μSv/h 137Cs source in 10 seconds. The angular resolution for resolving two 137Cs point-like sources was 15°. Additional simulated imaging of the 6.13 MeV gamma-rays from 14.1 MeV neutron scattering with water preliminarily demonstrated the imaging capability for high incident energy; (4) Conclusions: We concluded that the prototype had good imaging per-formance in a wide energy range (0.3~7 MeV), which showed potential in several MeV gam-ma-ray imaging applications.

This manuscript presents a system that can generate a 2D grid map and a 3D voxel model of an environment by fusing multiple sensors integrated into a robot. The fusion of these sensors is done by utilizing Robot Operating System (ROS) and some of its libraries. The sensors that are fused in the robot are a Light Detection and Ranging (LIDAR), Inertial Measurement Units (IMU), wheel encoders, and a Time-of-Flight camera. With the fusion of the point cloud data information obtained with the Time-of-Flight camera, the laser information of the LIDAR sensor, in addition to the odometry generated with the other sensors, a 2D grid map and a 3D model of two different environments were created, thus testing the performance of the system.

Atopic dermatitis (AD) is a chronic inflammatory disorder presenting a dysregulated immune response and derangement of the epidermal barrier lipids. The Th2-type cytokines interleukin IL-4 and IL-13 play a prominent role in AD by activating the Janus Kinase/Signal Transduction and Activator of Transcription (JAK/STAT) intracellular signal axis. This study aimed to investigate the role of JAK/STAT in the lipid perturbations induced by Th2 signaling in 3D-epidermal equivalents. We used tofacitinib, a low-molecular-mass JAK inhibitor, to screen for the JAK/STAT-mediated deregulation of lipid metabolism. Th2 cytokines decreased the expression of elongases 1, 3, and 4, and serine-palmitoyl-transferase and increased that of sphingolipid delta(4)-desaturase, and carbonic anhydrase 2. Th2 cytokines inhibited the synthesis of palmitate and caused a depletion of triglycerides. This depletion was associated with altered PC profiles and fatty acid (FA) metabolism. Overall, the ceramide profiles were minimally affected. Except for most sphingolipids and very long chain FAs, the effects of Th2 on lipid pathways were reversed by co-treatment with tofacitinib. An increase in the mRNA levels of CPT1A and ACAT1, reduced by tofacitinib, suggests that Th2 cytokines promote FA beta-oxidation. In conclusion, pharmacological inhibition of JAK/STAT activation prevents the lipid disruption caused by halted homeostasis of FA metabolism.

AVs suffer reduced maneuverability and performance due to the degradation in sensor performances in fog. Such degradation causes significant object detection errors essential for AVs' safety-critical conditions. For instance, YOLOv5 performs significantly well under favorable weather but suffers miss detections and false positives due to atmospheric scattering caused by fog particles. Existing deep object detection techniques often exhibit a high degree of accuracy. The drawback is being sluggish at object detection in fog. Object detection methods with fast detection speed have been obtained using deep learning at the expense of accuracy. The problem of the lack of balance between detection speed and accuracy in fog persist. This paper presents an improved YOLOv5-based multi-sensor fusion network that combines radar's object detection with a camera image bounding box. We transformed radar detection by mapping the radar detections into a two-dimensional image coordinate and projected the resultant radar image on the camera image. Using the attention mechanism, we emphasized and improved important feature representation used for object detection while reducing high-level feature information loss. We trained and tested our multi-sensor fusion network on clear and multi-fog weather datasets obtained from the CARLA simulator. Our result shows that the proposed method significantly enhances the detection of distant and small objects. Our small CR-YOLOnet model best strikes a balance between accuracy and speed with an accuracy of 0.849 at 69 fps.

The 3D reconstruction method using RGB-D camera has a good balance in hardware cost, point cloud quality and automation. However, due to the limitation of inherent structure and imaging principle, the acquired point cloud has problems such as a lot of noise and difficult registration. This paper proposes a three-dimensional reconstruction method using Azure Kinect to solve these inherent problems. Shoot color map, depth map and near-infrared image of the target from six perspectives by Azure Kinect sensor. Multiply the 8-bit infrared image binarization with the general RGB-D image alignment result provided by Microsoft to remove ghost images and most of the background noise. In order to filter the floating point and outlier noise of the point cloud, a neighborhood maximum filtering method is proposed to filter out the abrupt points in the depth map. The floating points in the point cloud are removed before generating the point cloud, and then using the through filter filters out outlier noise. Aiming at the shortcomings of the classic ICP algorithm, an improved method is proposed. By continuously reducing the size of the down-sampling grid and the distance threshold between the corresponding points, the point clouds of each view are continuously registered three times, until get the complete color point cloud. A large number of experimental results on rape plants show that the point cloud accuracy obtained by this method is 0.739mm, a complete scan time is 338.4 seconds, and the color reduction is high. Compared with a laser scanner, the proposed method has considerable reconstruction accuracy and a significantly ahead of the reconstruction speed, but the hardware cost is much lower and it is easy to automate the scanning system. This research shows a low-cost, high-precision 3D reconstruction technology, which has the potential to be widely used for non-destructive measurement of crop phenotype.

Previous research has shown that the effectiveness of selecting filter set from a large set of commercial broadband filters by vector analyzing method based on maximum linear independence (MLI). However, the traditional MLI is suboptimal due to predefining the first filter of the selected filter set being the maximum ℓ2 norm among all those of the filters. An exhaustive imaging simulation is conducted to investigate the features of the most competent filter set. In the simulation, every filter in a subset of all the filters is selected serving as the first filter in turn. From the results of the simulation, we found there are remarkable characteristics for the most competent filter set. Besides smaller condition number, the geometric features of the best-performed filter set comprise the distinct peak of the transmittance of the first filter, the generally uniform distributing of the peaks of the transmittance curve of the filters, the substantial overlapping of the transmittance curves with those of the adjacent filer sets. Therefore, the best-performed filter sets can be decided intuitively by simple vector analyzing and just a few experimental verifications. This work would be useful for optimizing spectral sensitivity of broadband multispectral imaging sensors or SFA sensors.

A method of measuring the absolute pose parameters of a moving rigid body using a monocular camera is proposed, aiming at addressing calibration difficulties and inconsistencies of repeated measurements of the rigid-body pose for a camera having a varying focal length. The proposed method does not require calibration beforehand. Using more than six non-coplanar control points symmetrically arranged in the rigid-body and world coordinate systems, the matrices of rotation and translation between the camera and two coordinate systems are obtained and the absolute pose of the rigid body measured. In this paper, formulas of the absolute pose measurement of a moving rigid body are deduced systematically and the complete implementation is presented. Position and attitude measurement experiments carried out on a three-axis precision turntable show that the average absolute error in the attitude angle of a moving rigid body measured by an uncalibrated camera at different positions changes by no more than 0.2 degrees. Analysis of the three-dimensional coordinate errors of the centroid of a moving rigid body shows little deviation in measurements made at three camera positions, with the maximum deviation of the average absolute error being 0.53 cm and the maximum deviation of the standard deviation being 0.66 cm. The proposed method can measure the absolute pose of a rigid body and is insensitive to the position of the camera in the measurement process. This work thus provides guidance for the repeated measurement of the absolute pose of a moving rigid body using a monocular camera.

This study presents a comprehensive ecological evaluation of avian species based on 5,322 photographs obtained through camera-trap sampling. We identified 1,427 independent bird sightings, encompassing 26 families and 49 species. The study focused on temporal activity patterns, nesting behaviors, habitat preferences, and the overlap coefficient of activity patterns among 22 species of Passeriformes. Two species exhibited predominant morning activity, while five species were active in the afternoon, and 15 exhibited cathemeral activity (activity throughout the day). A cross-analysis revealed varying degrees of overlap in the activity patterns of pairs of species with similar behavioral ecology. Our findings indicate that despite exhibiting similar ecological behavior, these species display unique activity patterns, likely influenced by factors such as resource availability, competition avoidance, and thermoregulation strategies. The results highlight the richness and complexity of avian temporal niches and emphasize the need for further research into their correlation with environmental factors. This study contributes to a deeper understanding of niche separation within Passeriformes and expands our knowledge of avian behavioral ecology.

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

This study introduces a multilayer perceptron (MLP) error compensation method for real-time camera orientation estimation, leveraging a single vanishing point and road lane lines within a steady-state framework. The research emphasizes cameras with a roll angle of 0°, predominant in autonomous vehicle contexts. The methodology estimates pitch and yaw angles using a single image and integrates two Kalman filter models with inputs from image points (u, v) and derived angles (pitch, yaw). Performance metrics, including AE, MINE, MAXE, SSE, and STDEV, were utilized, testing the system in both simulator and real-vehicle environments. The outcomes indicate that our method notably enhances the accuracy of camera orientation estimations, consistently outpacing competing techniques across varied scenarios. This method’s potency is evident in its adaptability and precision, holding promise for advanced vehicle systems and real-world applications.

In the tissue regeneration field, stem cell transplantation and the control of their differentiation represent a promising therapeutic strategy. The second aspect can be achieved using electrical stimulation. This study aims to characterize the effect of a microsecond electrical stimulation on MSCs and iNSCs, in the context of the RISEUP FET-OPEN project (n. 964562) that seeks to control these cells differentiation for the spinal cord injury treatments. Here, the effect of a specific microsecond electric pulses stimulation, characterized by bipolar pulses of 100 µs + 100 µs, delivered for 30 minutes at an intensity of 250 V/cm, on i) cell proliferation, ii) cell cycle, iii) gene expression and iv) apoptosis was evaluated. Results show that the stimulation does not affect cell proliferation, cell cycle, and apoptosis, but induced some variations in gene expression, in particular in EGR1, FOS, and POU5F1. These ob-servations led us to deeply investigate the cell proliferation until 72h from the stimulation observing an increase in the iNSCs. The main outcome of this study is that the chosen stimulation protocol is safe and not toxic for MSCs and iNSCs. The observed variations in the gene expression need to be deeply investigated to assess the molecular mechanisms involved.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.