The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

The exceptional performance advantages of the fiber optic gyroscope (FOG) position it as a dominant player in middle and high-end inertial navigation systems. To prevent the loss of sensor precision caused by algorithm design and simplify the complex modeling strategy in traditional methods. We gradually demonstrate the significant role of Convolutional Neural Network (CNN) in the navigation system based on FOG, and utilize the particle swarm optimization algorithm (PSO) to expedite the convergence of the network. The experimental results demonstrate that the initial alignment method based on deep learning is more accurate than the traditional method. The attitude angle error is reduced by 81.25%, 92.54% and 36.53% respectively. The research provides support for the future application of deep learning in optical navigation systems.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

A large core size and bending resistance are very important properties of mid-infrared energy transfer fibers, but large core sizes usually lead to a deterioration of bending properties. A negative-curvature nested node-free anti-resonant hollow-core fiber (AR-HCF) based on quartz is proposed. It was made by adding a nested layer to a previous AR-HCF design to provide an additional anti-resonance region while keeping the gap between adjacent tubes strictly correlated to the core diameter to produce a node-free structure. These features improve the fiber’s bending resistance while achieving a larger core diameter. The simulation results show that the radial air-glass anti-resonant layer is increased by the introduction of the nested anti-resonant tube, and the weak interference overlap between the fiber core and the cladding mode is reduced, so the fiber core’s limiting loss and the sensitivity to bending are effectively reduced. When the capillary wall thickness t of the fiber is 0.71 μm, the core diameter D is 70 μm, the ratio of the inner diameter of the cladding capillary to the core diameter d/D is 0.62, and the diameter of the nested tube is d0=29 μm, the fiber has a lower limiting loss at the wavelength of 2.79 μm, and the limiting loss is 3.28×10-4 dB/m. At the same time, the optimized structure also has good bending resistance. When the bending radius is 30 mm, the bending loss is only 4.72×10-2 dB/m. To our knowledge, this is the first research to achieve an anti-bending low-loss micro-structure hollow fiber with a bending radius of less than 30 mm in the 2.79 μm band. An anti-bending low-loss anti-resonant hollow-core fiber with this structure constitutes a reliable choice for the light guiding system of a 2.79 μm band erbium laser therapy instrument.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

Disposable surgical gowns are usually made from petroleum-based synthetic fibers that do not naturally decompose, impacting the environment. A promising approach to diminish the environmental impact of disposable gowns involves utilizing natural fibers and/or bio-based synthetic fibers. In this study, composite web from polylactic bicomponent fiber and natural fibers, cattail and kapok fiber, were prepared by hot-press method. Only the sheath region of the PLA bicomponent fiber melts, acting as an adhesive that enhanced the strength and reduced the thickness of the composite web compared to its state before hot-pressing. Mechanical and physical properties of composite webs were evaluated. Composite webs created from kapok fiber displayed a creamy yellowish-white color, while those made from cattail fiber showed a yellowish-brown color. Composite webs exhibit hydrophobic properties when adding the natural fiber. The maximum natural fiber content, at a ratio of 30, can be incorporated into composite webs while preserving mechanical properties and proper water vapor permeability. This nonwoven material presents an alternative with the potential to replace petroleum-based surgical gowns.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

This study investigates the unique morphology and mechanical properties of multi-jet electrospun cashew gum (CG) when combined with high molecular weight polyethylene oxide (PEO) and glycerol. Cashew gum (CG) is an inexpensive, non-toxic polysaccharide derived from Anacardium occidentale trees. Initially, the electrospinnability of aqueous solutions of cashew gum alone or in combination with PEO was evaluated. It was found that cashew gum alone was not suitable for electrospinning; thus, adding a small quantity of PEO was needed to create the necessary molecular entanglements for fiber formation. By using a single emitter with a CG:PEO ratio of 85:15, straight and smooth fibers with some defects were obtained. However, additional purification of the cashew gum solution and the incorporation of glycerol as a plasticizer were necessary to produce defect-free straight and smooth fibers. Interestingly, when the optimized formulation was electrospun using multiple simultaneous emitters, thicker aligned fiber bundles were achieved. Moreover, the resulting oriented fiber mats exhibited unexpectedly high elongation at break at ambient conditions. These findings highlight the potential of this bio-polysaccharide-based formulation for non-direct water contact applications requiring elastic properties.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

Road infrastructure is a key public asset because it benefits the social and economic development of any country. It plays an important role for the development of the industrial complex, the production sector and the road surfaces of transport roads should be of high quality, have a long service life. Road infrastructure, as well as all infrastructure, requires preservation, maintenance and repair. There are special requirements for the roadway that must be observed during construction or repair. This article is devoted to a detailed study of the use of fiber optics sensors (FOS) based on the fiber Bragg grating (FBG) for road surface monitoring. Such a fiber sensor consisting of a fiber Bragg grid and a pair of grids can offer the possibility of simultaneous measurement of deformation and temperature for monitoring the pavement. Temperature and deformation measurements were carried out by installing a sensor on the surface of a made asphalt sample. The built-in fiber sensor based on FBG provides important information about how the pavement structure can withstand the load, subsidence of soil, timely implement road safety and stability measures evaluate and predict the service life of the pavement. The results of the study showed that the synchronicity, repeatability and linearity of the characteristics of the fiber sensor are excellent. The difference between the experimental and theoretical results is about 7%. Thus, based on the results of the obtained data, the fiber sensor on the FBG can be used for monitoring, designing road surfaces and in general transport infrastructure.

Five years ago, the concept of addressed fiber Bragg structures (AFBS) was proposed, which simultaneously perform the functions of a two-frequency radiation shaper, the difference frequency of which is the AFBS address, and a sensitive element, since the value of the difference frequency is invariant to measured physical fields, and the set of difference frequencies, moreover, is orthogonal in the array of such sensors, enabling their address multiplexing. In this article, we provide an overview of the theory and technology of AFBS, including the structures with three or more spectral components with various combinations of difference frequencies, symmetrical and asymmetric, performing the functions of the address and converting information signals to the low-frequency range at the same time, along with other functions. The subjects of interrogation of these structures, their fabrication and calibration are discussed as well. We also consider a wide range of applications in which AFBS can be used, covering such areas as oil and gas production, power engineering, transport, medicine, etc. In addition, the prospects of AFBS further development are proposed.

Nutrition is crucial for the management of patients affected by chronic kidney disease (CKD) to slow down disease progression and to correct symptoms. The mainstay of the nutritional approach to renal patients is protein restriction coupled with adequate energy supply to prevent malnutrition. However, other aspects of renal diets, including fiber content, can be beneficial. This paper summarizes the latest literature on the role of different types of dietary fiber in CKD, with special attention to intestinal microbiota and the potential protective role of renal diets. Fibers have been identified based on aqueous solubility, but other features, such as viscosity, fermentability, and bulking effect in the colon should be considered. A proper amount of fiber should be recommended not only in the general population but also in CKD patients, to achieve an adequate composition and metabolism of intestinal microbiota and to reduce the risks connected with obesity, diabetes, and dyslipidemia.

The interest in obtaining new composite materials with diverse properties has created a growing interest in natural fi-bers as reinforcement in polymers, which has generated an impact in sectors such as automotive and construction, dis-placing synthetic fibers. Properties such as low density, low cost, and rene.wable make these fibers an attractive alterna-tive to reduce environmental impact. Their application in polymers, such as polypropylene, polyethylene, and epoxy resins, has allowed the modification of polymeric composite materials' mechanical and physical properties (NFRP). This review focuses on investigating the status of natural fiber-reinforced polymers. It analyzes their worldwide demand, chemical characteristics, physical and mechanical properties, and various applications in different sectors and indus-tries. In addition, the advantages and disadvantages of NFRPs are highlighted, highlighting their potential for new ap-plications.

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Cotton fiber, a crucial and sustainable resource for global textile production, undergoes a complex five-stage developmental process, encompassing initiation, elongation, transition, secondary cell wall biosynthesis, and maturation. These elongated single-cell fibers originate from the outer ovule epidermis. The development of cotton fibers involves intricate changes in gene expression and physiological processes, resulting in a nearly pure cellulose product vital for the global cotton industry. Decoding genes associated with fiber development enhances our understanding of cotton fiber mechanisms and facilitates the cultivation of varieties with enhanced quality. In recent decades, advanced omics approaches, including genomics, transcriptomics, and proteomics, have played a pivotal role in identifying genes and gene products linked to cotton fiber development, including the MYB transcription factor family which coordinates cotton fiber development. Molecular studies have revealed transcription factors like MYB, WRKY, Homeodomain Leucine Zipper (HD-ZIP) and basic Helix-Loop-Helix (bHLH) influencing fiber initiation and elongation. The intricate interplay of phytohormones like auxin, gibberellic acid (GA), brassinosteroid (BR), jasmonic acid (JA), ethylene, abscisic acid (ABA), and cytokinin is explored, providing a comprehensive perspective on shaping cotton fibers. Numerous candidate genes and cellular processes affecting various aspects of fiber development hold promise for genetic engineering or marker-assisted breeding to improve fiber quality. This review presents a comprehensive overview of key achievements in cotton molecular biology, with a specific emphasis on recent advancements in understanding transcription factors and phytohormones involved in cotton fiber initiation and elongation.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.

Mode locked pulse generation has been reported using both active and passive mode locking schemes. Active mode locking technique has been proven to be an effective way to generate high-repetition-rate pulses by incorporating a modulator inside the laser cavity. Compared to actively mode locked lasers, passively mode locked lasers can generate pulse train at ultrashort pulse width but with relatively lower repetition rate. Thus, it is a brilliant idea to build a hybrid mode locked system combining both active and passive mode lockers. In this review, several hybrid mode locked fiber ring laser systems are discussed and summarized. Hybrid mode locking is a promising method to generate high speed ultrashort optical pulses for fiber-optic telecommunication system.

The aim of the study was to assess the effect of the addition of inulin and the replacement of part of inulin with apple fiber on the physicochemical and organoleptic properties. Moreover, the survival of Bifidobacterium animalis ssp. Lactis Bb-12 and Lactobacillus rhamnosus was studied in sheep milk ice cream. There was no effect of apple fiber and the type of bacteria on the number of bacteria of the probiotics after fermentation. As a result of freezing, mixture containing Bifidobacterium animalis ssp. Lactis Bb-12, there was a significant reduction in the bacterial from 0.39 log cfu g −1 to 0.46 log cfu g −1. In all ice cream on the 21st day of storage, it exceeded 10 log cfu g –1, which means that the ice cream retained the status of probiotic products. The Lactobacillus rhamnosus ice cream showed a lower yellow colour compared to the Bifidobacterium Bb-12 ice cream. The overrun of sheep's milk ice cream was within a range from 78.50% to 80.41%. The appearance of sheep's milk ice cream is influenced considerably by the addition of fiber and the type of bacteria and the interaction between the type of bacteria and the addition of fiber and storage time and fiber.

Blending lignin as the second most abundant polymer in nature with nanostructured compounds such as dendritic polymers will not only add value to lignin, but also increase its application in various fields. In this study, softwood Kraft lignin/polyamidoamine dendritic polymer (PAMAM) blends were fabricated by solution electrospinning method to produce bead-free nanofiber mats. The mats were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), zeta potential, and thermogravimetry analysis (TGA). The chemical intermolecular interactions between lignin functional groups and abundant amino groups in PAMAM were investigated by FTIR and viscosity measurement. These interactions enhanced the mechanical and thermal characteristics of lignin/PAMAM mats, providing further potential applications at industry level.

The damage caused by global warming is rapidly increasing, and its adverse effects become more evident with each passing day. Although it is known that the use of alternative binder materials in concrete would decrease this negative effect, reluctance to new composites continues. Waste use plays a vital role in sustainability studies. In this study, pure cement paste was prepared and enriched with carbon fiber. This study investigated the wide range of volume fraction of carbon fiber in cement-based composites. Two different industrial wastes, marble dust, and bottom ash were chosen and mixed with cement and four different (0.3%, 0.75%, 1.5%, and 2.5%) carbon fiber volume fractions. Based on physical, mechanical, and durability tests at 7, 28, and 56-days of curing, the composites were resistant to sulfate and seawater attack. The 0.75% carbon fiber addition seems to be an optimum volume percentage beyond which both physical and mechanical properties were adversely affected. The composites with 0.75% carbon fiber have reached 48.4 MPa and 47.2 MPa at 56-days of curing for marble dust and bottom ash mixture groups, respectively.

The paper presents construction, laboratory tests as well as the first field application of a new fiber-optic rotational seismograph. The system based on fiber-optic gyroscope (FOG) with determined Angle Random Walk of the order of 10-8 rad/Sqrt(s) and a few rad/s maximum detectable amplitude of rotation in the frequency range from DC to 328.12 Hz. It has been designed for rotational seismology area of interest. This work also presents exemplary relevant measurements which were conducted using a set of two devices installed in the geophysical observatory in Książ, Poland.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

The distributed long-range sensing system using the standard telecommunication single-mode optical fiber in a function of a distributed sensor for sensing of mechanical vibrations is described. Various events generating vibrations such as walking or running person, moving cars, trains and others can be detected, localized and classified. The sensor and related sensing system components were designed and constructed and the system was tested both in the laboratory and in the real situation with 88 km telecom optical link, and the results are presented.

Abstract: This paper is focusing on the stabilisation of soil using jute fibre as soil stabilizer. Stabilisation is the process of modifying the properties of a soil to improve its engineering performance and used it for a variety of engineering works. This study examines the potential of soil stabilization with jute fibre when it is cut into roughly 30mm lengths as stabilizer. The varying percentages like 0.5%, 1%, 1.5 and 2% of pieces of jute fibre were used and mixed it with soil. The laboratory tests such as California Bearing Ratio (CBR) test, modified compaction tests and direct shear strength tests have been conducted to observe the change in engineering properties of soil. On the basis of the experiments performed, it can be concluded that the stabilization of soil using 30mm pieces of jute as stabilizer improves the strength characteristics of the soil so that it becomes usable as one of the reinforcing material for the construction of roadways, parking areas, site development projects, airports and many other situations where sub-soils are not suitable for construction.

A number of third order nonlinear processes can occur in single-mode fibres and an understanding of such phenomena is almost a prerequisite for actual lightwave-system designers. In this paper we review the main limitations imposed by several nonlinear effects, namely the self- and cross-phase modulation, four-wave mixing, stimulated Raman scattering and stimulated Brillouin scattering, on the performance of optical fiber communication systems.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

Distributed fiber optic vibration sensors based on Φ-OTDR using Rayleigh backscattering of highly coherent light source pulses are very popular type in the area of sensors due to many attractive features, mainly due to its distributed manner of sensing, i.e. they can operate as thousands of local sensors simultaneously. The paper summarizes and describes several important modifications of the original sensor scheme to enhance its key performance parameters and to extend its application potential. A multi-fiber sensor form was proposed. Single- and two-fiber sensors were designed, constructed and tested both in the laboratory and in a real environment. Variants of two-fiber sensor utilizing optical switches for the sensor flexibility enhancement are proposed and their applications are described.

Electro-spun ultra-fine fibers exhibit two significant properties: a high surface-to-volume ratio and a relatively defect-free molecular structure. Due to the high surface-to-volume ratio, electro-spun materials are well suited for activities requiring increased physical contact, such as providing a site for a chemical reaction or filtration of small-sized physical materials. However, electrospinning has many shortcomings, including difficulties in producing inorganic nanofibers and a limited number or variety of polymers used in the process. The fabrication of nanofiber bundles via electrospinning is explored in this analytical study, as well as the relationship between extrinsic electrospinning parameters and the relative abundance of various fiber morphologies. Numerous variables could impact the fabrication of nanofibers, resulting in a variety of morphologies; therefore, adequate ambient conditions and selecting the appropriate solvent for achieving a homogenous polymer solution and uniform electro-spun materials are examined. Finally, common polymers suitable for electrospinning and the promising applications of ultra-fine fibers achieved via electrospinning are studied in this paper.

The interest in random fiber lasers (RFLs), first demonstrated one decade ago, is still growing and their basic characteristics have been studied by several authors. RFLs are open systems that present instabilities in the intensity fluctuations due to the energy exchange among their non-orthogonal quasi-modes. In this work, we present a review of the recent investigations on the output characteristics of a continuous-wave erbium-doped RFL, with emphasis on the statistical behavior of the emitted intensity fluctuations. A progression from the Gaussian to Lévy and back to the Gaussian statistical regime was observed by increasing the excitation laser power from below to above the RFL threshold. By analyzing the RFL output intensity fluctuations, the probability density function of emission intensities was determined, and its correspondence with the experimental results was identified, enabling a clear demonstration of the analogy between the RFL phenomenon and the spin-glass phase transition. A replica-symmetry-breaking phase above the RFL threshold was characterized and the glassy behavior of the emitted light was established. We also discuss perspectives for future investigations on RFL systems.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Temperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in hazardous working environments (air pollution, chemical or ionizing contamination), and the presence of electromagnetic disturbances. The use of fiber optic temperature sensors in polymer technology can significantly reduce the cost of their production. Moreover, the installation process and usage would be simplified. As a result, these types of sensors would becoming increasingly popular in industrial solutions. This review provides a critical overview of the latest development of fiber optic temperature sensors based on Fabry-Perot interferometer made with polymer technology.

The epidermal cells on the surface of the cotton ovules undergo differentiation to produce fibers, which are single-celled hair-like protrusions resembling the plant trichomes. The initiation of these unicellular fibers from the cotton ovule surface is a complex and tightly regulated process. The initiation step is the cell fate-determining stage, which leads to the commitment of cells that eventually developed into fibers, thus becomes the most crucial phase in fiber development. The in-depth knowledge of molecular regulation is a prerequisite to get a clear view of the fiber initiation process's genetic and epigenetic control. The identification and functional validation of cotton fiber initiation-related genes, few fibreless mutants, transcription factors, microRNAs, epigenetic regulators, as well as the elucidation of the role of phytohormones as signaling molecules, has played a significant role in understanding the cotton fiber initiation process at the molecular level. This review focuses on the comprehensive information regarding the genetic and epigenetic regulation of cotton fiber initiation. Thus, the review will provide readers insight into mechanistic details that operate during cotton fiber initiation.

Extinction of natural resources builds up pressure on governments to invest in research to find more sustainable resources for construction sector. Earlier studies on mortar and concrete show that bottom ash and basalt fiber are independently alternative binder in the concrete sector. This study aims to use bottom ash and basalt fiber blends as alternative novel-based composites in pure cement paste. Strength and durability properties of two different percentages of bottom ash (40% and 50%) and three volume fractions of basalt fiber (0.3%, 0.75%, and 1.5%) were used at three curing periods (7, 28, and 56 days). In order to measure physical properties of the basalt-reinforced bottom ash cement paste composites flowability, dry unit weight, porosity and water absorption measurements at 7, 28, and 56 days of curing were performed. Furthermore, mechanical properties of composites determined by unconfined compressive strength and flexural strength tests. Finally, to assess the durability sulfate-resistance and seawater-resistance tests have been performed on composites at 28 and 56 days of curing. Results showed that addition of basalt fiber improves physical, mechanical and chemical stability properties of paste up to a limiting basalt fiber addition (0.3% volume fraction) where above an adverse effect have been monitored. It is clear that observed results can lead to development of sustainability strategies in the concrete industry by utilizing bottom ash and basalt fiber as an alternative binder.

Polymer-derived SiC-polycrystalline fiber (Tyranno SA) shows excellent heat-resistance up to 2000^oC, and relatively high strength. Up to now, through our research, the relationship between the strength and residual defects of the fiber, which were formed during the production processes (degradation and sintering), has been clarified. In this paper, we addressed the relationship between the production condition and the surface roughness of the obtained SiC-polycrystalline fiber, using three different raw fibers (Elementary ratio: Si₁Al_0.01C_1.5O_0.4~0.5) and three different types of reactor (Open system, Partially-open system, and Closed system). With increase in the oxygen content in the raw fiber, the degradation during the production process easily proceeded. In this case, the degradation reactions (SiO+2C=SiC+CO and SiO₂+3C=SiC+2CO) in the inside of each filament become faster, and then the CO partial pressure on the surface of each filament is considered to be increased. In consequence, according to Le Chatelier’s principle, the surface degradation reaction and grain growth of formed SiC crystals would be considered to become slower. That is to say, using the raw fiber with higher oxygen content and closed system (highest CO content in the reactor), much smoother surface of the SiC-polycrystalline fiber could be achieved.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

The gut microbiota has been suggested as an important factor in the pathogenic mechanisms of amyotrophic lateral sclerosis (ALS). This study aimed to investigate whether the intake of different kinds of dietary fiber was related to the disease progression rate (∆FS) and survival time. In total, 272 sporadic ALS patients diagnosed according to the revised EI Escorial criteria were recruited from March 2011 and were followed-up until the occurrence of events or the end of September 2020. The events included percutaneous endoscopic gastrostomy, tracheostomy, and death. Dietary fiber intake was calculated based on a 24-hour dietary recall and classified according to five major fiber-rich foods: vegetables, fruits, grains, legumes, and nuts/seeds. Among the total participants, the group with ∆FS values lower than the mean ∆FS (0.75) was noted in the highest tertiles of total and vegetable fiber intake. Participants with the highest tertile of vegetable fiber intake showed longer survival in the Kaplan–Meier analysis (p = 0.033). Notably, vegetable fiber intake was negatively correlated with pro-inflammatory cytokine (interleukin [IL]-1β, IL-6, and monocyte chemoattractant protein-1) levels in the cerebrospinal fluid. This study showed that vegetable fiber intake could influence the disease progression rate and survival time. Further clinical trials are needed to confirm whether dietary fiber supplementation improves the prognosis of ALS.

Several biomedical products, like scaffolds, implants, prostheses, and orthoses, require materials having superior physicochemical and biological properties. Polyethylene terephthalate glycol (PETG) is being increasingly used for various biomedical applications. There are a few studies on PETG-based composites, however, natural fibers like silk short fibers reinfored PETG composites have not been attempted. Being a cost-effective widely available material, PETG-Silk combination can be potential biocomposite for several biomedical applications. Here, we report a novel short silk fiber reinforced PETG composite prepared by a wet-mixing route, ensuring homogenous dispersion of the filler. Different ratios (2-10%) of short silk fibers were used to prepare composites with varied compositions. The mechanical, physicochemical, and biological properties of the prepared composites were analyzed. Thermogravimetric analysis showed that such composites are thermally stable up to 390 °C and can be used for thermal extrusion-based manufacturing. The tensile modulus of the samples increased with fiber content; however, the failure strain reduced with fiber content. Furthermore, upon annealing, the tensile modulus increased but, the failure strain of the composites decreased, XRD study revealed that heat treatment has altered the crystalline nature of the composites. Finally, we evaluated the cytocompatibility of the prepared composites to assess their suitability for various biomedical applications.

The aim of this paper is to create a sensor model based on optical crystal fibers (PCF). The aim of this model is to find and identify zinc cadmium. This thesis looked at three different categories of concentrations. For sensor architecture, PCF was generated using single-mode fiber-to-end split fusion (SM-PCF-SM). In this experiment, a specific wavelength spectrum was used to alter the concentration of materials covering the fiber in order to demonstrate the fiber's sensing capability. The 550nm wavelength has been used as the optical source for the fiber. The change in the output power of the external light was monitored and changes were observed for each concentration of the concentrations around the fiber. It has been found that the fiber is sensitive to small changes in concentrations. The absorption of the fiber has been calculated for the incoming capacity, as well as the losses in the capacity outside the fiber.

Flax fiber appears as a suitable feedstock in the endeavor of deploying a sustainable biobased economy. Its environmental performance as reinforcement in composite materials has been studied in previous Life Cycle Assessments (LCAs). However, these studies only present a coarse Life cycle Inventory (LCI) and often fail to detail all processes of the supply chain or to represent the co-products. This paper aims to bridge this gap and provide data for future LCAs on flax fiber production and transformation.The study focuses on the impacts of producing a bio-based reinforcement material (a fabric product for non-aesthetic purposes) with a system expansion perspective. The functional unit is defined as the production of 2400 m² flax-based technical textile per year, this corresponds to one hectare of cultivated land. The geographical scope considers that the production occurs in France and that some manufacturing process are outsourced in China. A Sensitivity Analysis was carried out to assess the influence of the electricity mix in the various countries involved in the manufacturing cycle.A detailed life cycle inventory for flax fiber production and transformation was built and the environmental performance of a flax technical textile was assessed as a cradle-to-gate LCA. The fate of co-products was documented and was shown to contribute to the reduction of the generated environmental impacts. Through a cradle-to-gate LCA, a broader understanding of the environmental performance of a flax-based technical textile was presented by including the valorization of co-products and a wider set of analyzed impact categories, going therefore beyond the existing state-of-the-art. Results show agricultural activities and electricity production to be the biggest contributors to the environmental impacts of flax technical textile; contributions due to land use changes were minor in comparison. Very specifically for this case study, a sensibility analysis showed the influence of an all-French production to be more efficient from an environmental point of view.

The current study aims to develop a methodology for obtaining topology-optimal structures made of short fiber-reinforced polymers, which include the fluid-structure interaction. Accounting for the molding process during the internal iterations of topology optimization makes it possible to enhance the weight efficiency of structures—a crucial aspect, especially in aerospace. Anisotropy is considered through the fiber orientation tensor, which is modeled by solving the plastic molding equations for non-Newtonian fluids, and then introduced as a variable of the stiffness matrix during the structural analysis. The materials used were non-linearly modeled using an exponential-and-linear hardening law. The evaluation of weight efficiency in structures composed of short-reinforced composite materials using a dimensionless criterion is addressed. Experimental verification was performed to confirm the validity of the developed methodology. The evidence illustrates that considering anisotropy leads to stiffer structures and structural elements should be oriented in the direction of maximal stiffness. The load-carrying factor can be expressed in terms of failure criteria. The presented multidisciplinary methodology can be used to improve the quality of the design of structures made of short fiber-reinforced composites (SFRC) where high stiffness, high strength, and minimum mass are the primary required structural characteristics.

Thermoplastic pultrusion is a suitable process for fabricating continuous unidirectional thermoplastics with a uniform cross-section, high mechanical properties due to continuous fiber reinforcement, low cost, and suitability for mass production. In this paper, jute and glass fibers were reinforced with a polypropylene matrix and fabricated using the thermoplastic pultrusion process. The volumetric fraction of the composite was designed by controlling the filling ratio of the reinforcing fiber and matrix. The effects of molding parameters were investigated, such as pulling speed and molding temperature, on the mechanical properties and microstructure of the final rectangular profile composite. The pulling speed and molding temperature were varied from 40 to 140 mm/min and 190 to 220°C, respectively. The results show that an increase in molding temperature initially led to an increase in mechanical properties, up to a certain point. Beyond that point, they started to decrease. The increase in molding temperature also led to an increase in void content. Meanwhile, un-impregnation decreased with the increase in molding temperature, and the jute fiber began to degrade at high temperatures. In the next step, with varying pulling speed, the mechanical properties decreased as the pulling speed increased, with a corresponding increase in void content and un-impregnation. The decrease in mechanical properties was influenced by the increase in void content and un-impregnation, as the jute fiber degraded at higher temperatures.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

Optical fiber sensors based on tapered optical fiber (TOF) structure have attracted a considerable amount of attention from researchers due to the advantages of simple fabrication, high stability, diverse structures, and have great potential for applications in many fields such as physics, chemistry and biology. Compared with ordinary optical fibers, TOF with their unique structural characteristics significantly improve the sensitivity and response speed of fiber-optic sensors and broaden the application range. This review presents an overview of the latest research status and characteristics of fiber-optic sensors and TOF sensors. Then the working principle of TOF sensors, fabrication schemes of TOF structures, novel TOF structures in recent years, and the growing emerging application areas are described. Finally, the development trends and challenges of TOF sensors are prospected. The objective of this review is to convey novel perspectives and strategies for the performance optimization and design of TOF sensors based on fiber-optic sensing technologies.

Fiber aggregation in nanocomposites has an important effect on the macroscopic electrical performance. To quantitatively evaluate its effect, an index to characterize the degree of aggregation is imperative, and ideally it should have three features simultaneously, i.e., single-parametric, dimensionless and physically meaningful, applicable to different aggregation topologies, and one-to-one corresponding to material electrical properties. To this end, a new aggregation degree is proposed, which is defined as the average increased number of fibers that connect with each one when fibers aggregate from a uniformly distributed state. This index is applicable to different aggregation topologies from lump-like aggregating clusters to network-like aggregating clusters. This index is proven to only depend on the local features of aggregating clusters, and can be concisely expressed by the characteristic parameters of local structure, via geometric probability analysis and numerical validations. Further, a one-to-one linear relation between the aggregation degree and percolation threshold is established by Monte Carlo simulations, which is independent of the distribution law of the fibers. This work provides a guide to the property characterization, performance prediction and material design of nanocomposites, and also gives a physical insight into the understanding of systems with similar non-uniform distributions.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

In this paper, we introduced a comprehensive study, based on both numerical and experimental analyses, of side polished (SP) single mode fibers (SMF) to investigate their evanescent field interaction with air and liquid analytes. In particular, the finite element method (FEM) and the beam propagation method (BPM) are employed to predict the optical properties of the SP-SMF. An ad-hoc experimental setup has been designed and built to characterize the side polished single mode fiber when air, water, and isopropanol are set in the side polished region. The sensitivity of the analytes is obtained as 1.207 V/RIU. The performance in terms of effective refractive index and transmittance are reported to show how these SP-SMF can be efficiently used for calculating the liquid refractive index. The simulation and experimental results display the significant performance of the SP-SMF as a sensing element.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

Carbon fibers (CFs) cannot be directly used for the preparation of CF paper because of their chemically inert nature. Herein, the surface of CF was modified via the spontaneous oxidative self-polymerization of dopamine. By taking full advantage of the spontaneous oxidation and self-polymerization properties of PD to maintain the maximum strength of CFs, a polydopamine-modified CF paper (PDA-CFP) with excellent performance was prepared using PD-modified CFs (PDA-CFs), which increased the proportion of hydrophilic functional groups on the surface of carbon fibers, increased the O/C ratio on the CF surface by 6 times, and improved the bond strength between the modified CF and the adhesive by making full use of the interaction force between polydopamine and PVA fibers. In this way, the primary properties of the CF paper was improved. Overall, the results showed that the dispersion of CF was considerably improved by the dopamine modification. In addition, the primary physical properties of PDA-CFP were better than those of virgin CF paper (CFP-0). PDA-CFP exhibited a maximum tensile strength of 2.04 kN/m2, a minimum resistivity of 0.06055 Ω·cm and a minimum porosity of 72.4%. The tightness could be increased by up to 12.1%.

Deformation monitoring is beneficial to ensure the service safety of long tunnel. An three-direction (vertical, transverse and axial) deformation estimation method using long-gauge fiber Bragg grating (FBG) sensing technology is proposed and applied to a long tunnel by integrating mechanical analysis and field monitoring during the service state. The key issues of the proposed method for identifying the three-direction deformation are discussed, such as establishing the separation model of coupling strain on cross section, deriving the theory of deformation identification in three directions, and determining the sensor layout of the long tunnel. A major advantage of the proposed method is that the three-direction deformation of the tunnel can be monitored in real time using distributed long-gauge strain sensors. The numerical analysis and field test results verify the feasibility of the proposed method.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

3D printing with cement-based materials is a promising manufacturing technique for civil engineering applications that already allows for the design and the construction of complex and highly customized structures using a layer-by-layer deposition approach. Usually, in this type of additive manufacturing, a mixture of cement, water, aggregate and additives is extruded through a specific print head and deposited in successive layers to form the desired shape. The extrusion mechanism is one of the most expensive parts of the 3D printer. Also, for low scale 3D printers, based on the shape of the extruder and the geometry limitation of the mixing blade, the 3D mixture is often limited to a narrow range of materials due to the risk of layer splitting or blockage. Therefore, there is a need to develop affordable and feasible alternatives to the current design-fabrication-application approach of 3D printers. In this paper, various new designed mixtures of fiber reinforced mortars that can be 3D printed using only a commercially available screw pump are analyzed based on their fresh properties and mechanical characteristics. The reduced facility requirements in this approach allow 3D-printing to be more available for civil engineering applications. With further innovation in the future, this method and mixtures can be extended for sustainable and economically feasible printing of single-family housing units.

In this study, the influence of graphene oxide nanoparticles on the bond-slip behavior of fiber and fly ash based geopolymer paste was examined. Geopolymer paste incorporating graphene oxide nanoparticles solution was cast in half briquetted specimens and embedded with a fiber. Three types of fibers were used: steel, polypropylene, and basalt. The pullout test was performed at two distinct speeds: 1 mm/second and 3 mm/second. Results showed that the addition of graphene oxide increased the compressive strength of geopolymer by about 7%. The bond-slip responses of fibers embedded in geopolymer mixed with graphene oxide exhibited higher peak stress and toughness as compared to those embedded in normal geopolymer. Each fiber type also showed different mode of failure. Both steel and polypropylene fibers showed full bond-slip responses due to their high ductility. Basalt fiber, on the other hand, because of its brittleness, failed by fiber fracture mode which showed no-slip in pull out responses. Both bond strength and toughness were found to be rate sensitive. The sensitivity was higher in graphene oxide/geopolymer than in conventional geopolymer.

Due to the renewed variation in government and political systems inside and outside countries, and with the high tariffs at borders, the latter have become an outlet for terrorism and smugglers. Therefore, each country seeks to develop its own protection system, and the technologies used in these systems vary according to the severity and the importance of the installations to be protected, it is found that some of them are expensive and unnecessary, but other have good and variable levels of efficiency. Consequently, the idea of designing a surveillance system that can monitor and control access becomes indispensable. In the same context, this work is of crucial strategic and geopolitical importance. It combines pre-existing alarm and monitoring methods and revolutionary Internet of Things (IoT) application products, of which Wireless Sensor Networks (WSN) and Optical Fiber Sensors (OFS) are part of this application. This article presents the distribution of wireless radar nodes accompanying with a Bragg fiber sensor to identify each rolling intruder incoming the zone to be monitored, from the determination of its speed, weight and wheelbase distance.

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.

We present the generation and nonlinear frequency conversion of nanosecond cylindrical vector beams (CVBs) in two-mode fiber (TMF). Based on the polarized dependence vector mode coupling characteristic and the precise wavelength tunability of an acoustically-induced fiber grating (AIFG), the nanosecond cylindrical vector beams (CVBs, 1064 nm, 10 ns) is directly generated in a TMF with convenient switching characteristics between the radial and azimuthal vector beams. Furthermore, the stimulated Raman scattering (SRS) is produced based on the transmission of the nanosecond CVBs in the 100-meters long TMF, and the spatial intensity and polarization distributions characteristics the 1st-order Stokes shifted component is consistent with the nanosecond CVBs pump pulse. This work provides a method for achieving wavelength conversion of the CVBs in optical fiber.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

Fiber optic sensors cannot measure damage; for getting information about damage from strain measurements, additional strategies are needed, and several alternatives have been proposed. This paper discuss two independent concepts: the first one is based on detecting the new strains appearing around a damage spot; the structure does not need to be under loads; the technique is very robust, damage detectability is high, but it requires sensors to be located very close to the damage, so it is a local technique. The second approach offers a wider coverage of the structure, it is based on identifying the changes caused by the damage on the strains field in the whole structure for similar external loads. Damage location does not need to be known a priori, detectability is dependent upon the sensors network density, damage size and the external loads. Examples of application to real structures are given.

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

Cotton is the most important natural fiber cash crop, which has high commodity economic benefits and provides an important material foundation for China's construction. With the improvement of textile technology and living standard, higher requirements are put forward for raw cotton quality. Traditional cotton breeding methods need typing and selection. With the development of biotechnology and the research of genomics, genomic selection has been widely used in cotton breeding. Genomic selection is a new breeding method, which can be selected and bred by constructing a prediction model and using high-density molecular markers covering the whole genome. In this study, the application of various genomic selection models in cotton fiber quality was explored, which provided more reliable information for genetic breeding improvement in the future, thus helping to improve the efficiency of actual cotton breeding.

The dispersion properties of surface plasmon polaritons during propagation on metal wires with a dielectric coating in the terahertz frequency range are investigated theoretically. An analytical expression is obtained for a pulsed electric field from the solution of Maxwell equations taking into account high-order dispersion terms. The effect of the dielectric coating on the distortion of the pulse shape is analyzed. Unlike uncoated wire, the propagation of a surface plasmon pulses along a coated wire is highly dispersive. It is shown that the coating leads to the appearance of a long-chirped signal with a propagation of only a few millimeters, i.e. when a terahertz pulse propagates along a coated wire, it acquires a long oscillatory tail, the frequency of which depends on time.

The processes of soliton generation and interference focus on the complex nonlinear soliton dynamics resembling matter particles. In order to further understand the dynamic process of solitons from a multidimensional perspective, here we report the vectorial solitons nature under two-sets pulse splitting in a single cavity induced by dual-core fiber assisted ultrafast fiber lasers. Owing to the weakly coupled cores in symmetrical dual core fiber (SDCF), two pulse groups interaction are formed in a cavity. By using the dispersive Fourier transformation technique (DFT), it was found that the four-component polarized rotation vector solitons (PRVS) generate. Moreover, gradually increasing the power can obtain the locked soliton bound state in two core space, and the corresponding evolution is similar to that of non-degenerate bright solitons in Bose Einstein condensates (BEC). In addition, by properly controlling the soliton phase offset in SDCF, the soliton rain state of multi pulse evolution can be obtained. The related experimental results would be fruitful to the communities interested in soliton dynamics and frequency comb lasers.

The paper presents the results of a study of the concept of address fiber Bragg structures in the problem of vibration control. The mathematical model of measuring transformation is presented; the experimental study of a vibration diagnostics system based on Address Fiber Bragg Gratings is carried out; the quantitative and qualitative comparative assessment with electronic accelerometers is made; the gain by an order of magnitude in some parameters is shown.

The work presents an approach to instrument the load sensing bearings for automotive applications for estimation of the loads acting on the wheels. The system comprises fiber-optic sensors based on addressed fiber Bragg structures (AFBS) with two symmetrical phase shifts. A mathematical model for load-deformation relation is presented, and the AFBS interrogation principle is described. The simulation includes (i) modeling of vehicle dynamics in a split-mu braking test, during which the longitudinal wheel loads are obtained, (ii) the subsequent estimation of bearing outer ring deformation using a beam model with simply supported boundary conditions, (iii) the conversion of strain into central wavelength shift of AFBS, and (iv) modeling of the beating signal at the photodetector. The simulation results show that the estimation error of the longitudinal wheel force from the strain data acquired from a single measurement point was 5.44% with root-mean-square error of 113.64 N. A prototype load sensing bearing was instrumented with a single AFBS sensor and mounted in a front right wheel hub of an experimental vehicle. The experimental setup demonstrated comparable results with the simulation during the braking test. The proposed system with load-sensing bearings is aimed at estimation of the loads acting on the wheels, which serve as input parameters for active safety systems, such as automatic braking, adaptive cruise control, or fully automated driving, in order to enhance their effectiveness and safety of the vehicle.

We propose a 10-Gb/s 64-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes Reinforcement Learning (RL) SARSA based decision method to indicate an effective decision which mitigates nonlinearity. By utilizing RL-SARSA algorithm, the results demonstrate that significant reduction can be obtained in terms of bit error rate.

Being able to forecast events is of great importance in many fields, from brain behavior to earthquakes or stock markets. Because each dynamical system has intrinsic features, different statistical tools have to be used for each system. Here we study the time series of the output intensity of a fiber laser with an ordinal patterns analysis, and we look for temporal correlations in order to statistically forecast the most intense events. We set two thresholds, a low one and a high one, to distinguish between low intensity versus high intensity events. We find that when the time series is performing events below the low threshold it shows some preferred temporal patterns before performing events above a high threshold.

In this paper, we investigate an animal-human cohabitation problem with the help of machine learning and fiber-wireless (FiWi) access networks integrating cloud and edge (fog) computing. We propose an early warning system which detects wild animals nearby road/rail with the help of wireless sensor networks and alerts passing vehicles of possible animal crossing. Additionally, we show that animals' detection at the earliest and the related processing, if possible, at sensors would reduce the energy consumption of edge devices and the end-to-end delay in notifying vehicles, as compared to the scenarios where raw sensed data needs to be transferred up the base stations or the cloud. At the same time, machine learning helps in classification of captured images at edge devices, and in predicting different time-varying traffic profiles-- distinguished by latency and bandwidth requirements-- at base stations, including animal appearance events at sensors, and allocating bandwidth in FiWi access networks accordingly. We compare three scenarios of processing data at sensor nodes, base stations and a hybrid case of processing sensed data at either sensors or at base stations, and showed that dynamic allocation of bandwidth in FiWi access networks and processing data at its origin leads to lowering the congestion of network traffic at base stations and reducing the average end-to-end delay.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

The review aims to assess fifteen (15) academic literature sources, highlighting the application of machine learning algorithms in the maintenance operations of optical fiber networks. It exhibits the collection of data using PRISMA methodology—Preferred Reporting Item for Systems Review and Meta-Analyses. The application, results, and performance metrics are discussed based on the collected observations, computations, and statistics in the studies, which revealed records of high accuracy degrees ranging from 86% to 98% on average and quality ML models including Neural Networks (NNs), Support Vector Machines (SVMs), and LSTM, as well as deep learning models that disclosed effective results of determining challenges and problems within the optical fiber lines. The review mainly centralized on superior machine learning technologies that surpass traditional techniques in fault detection and localization for improved optical fiber networks’ operations while providing insights into the limitations and challenges encountered in real-world applications of these models, offering a comprehensive perspective on the optical fiber network’s domain.

Fiber coupling efficiency is one of the key technical indicators of atmospheric laser communication, which directly affects the communication system BER. According to the optical fiber coupling efficiency model, the optical fiber coupling model under atmospheric slant link is established, and the relationship between wavelength, zenith angle, receiving aperture, altitude and coupling efficiency is studied through numerical simulation. Based on the principle of adaptive optics turbulence correction, the relationship between fiber coupling efficiency and adaptive optics order is established. A fast method for estimating the coupling efficiency based on Strehl ratio is proposed. According to the principle of laser communication system, the semi-physical simulation experimental system of atmospheric slant-range channel coupling efficiency is constructed, and the coupling efficiency test and analysis are completed.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

In this study, divalent Yb2+-doped silica fiber was fabricated using rod-in-tube technology. The fiber core of Yb2+-doped silica glass was prepared by high-temperature melting technology under vacuum conditions. The spectroscopic properties of the Yb2+-doped glass and fiber were studied. The experiments indicate that divalent Yb2+-doped glass has a high quantum efficiency and superbroadband fluorescence in the visible region with an excitation wavelength of 405 nm. In additionally, the results suggest that Yb2+-doped fiber has a potential for application in visible fiber laser and fiber amplification.

The Pashmina and Barbari are two famous goat breeds found in the wide areas of the Indo-Pak region. Pashmina is famous for its long hair-fiber (Cashmere) production while Barbari is not-selected for this trait. So, the mRNA expression profiling in the skin samples of both breeds would be an attractive and judicious approach for detecting putative genes involved in this valued trait. Here, we performed differential gene expression analysis on publicly available RNA-Seq data from both breeds. Out of 44,617,994 filtered reads of Pashmina and 55,995,999 of Barbari which are 76.48% and 73.69% mapped to the ARS1 reference transcriptome assembly respectively. A pairwise comparison of both breeds resulted in 47,159 normalized expressed transcripts while 8,414 transcripts are differentially expressed above the significant threshold. Among these, 4,788 are upregulated in Pashmina while 3,626 transcripts are upregulated in Barbari. Fifty-nine transcripts harbor 57 genes including 32 LOC genes and 24 are annotated genes which were selected on the basis of TMM counts > 500. Genes with ectopic expressions other than uncharacterized and LOC symbol genes are Keratins (KRT) and Keratin Associated Proteins (KRTAPs), CystatinA&6, TCHH, SPRR4, PPIA, SLC25A4, S100A11, DMKN, LOR, ANXA2, PRR9 and SFN. All of these genes are likely to be involved in keratinocyte differentiation, sulfur matrix proteins, dermal papilla cells, hair follicles proliferation, hair curvature, wool fiber diameter, hair transition, hair shaft differentiation and its keratinization. These differentially expressed reported genes are critically valuable for enhancing the quality and quantity of the pashmina fiber and overall breed improvement. This study will also provide important information on hair follicle differentiation for further enrichment analyses and introducing this valued trait to other goat breeds as well.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

Background: Lithium di-silicate dental ceramics bonding, realized by using different resins, is strictly dependent on micro-mechanical retention and chemical adhesion. The aim of this in vitro study was to investigate the capability of a 1070 nm fiber laser for their surface treatment. Methods: Samples were irradiated by a pulsed fiber laser at 1070 nm with different parameters (Peak Power from 5 kW to 5 kW, RR 20 kHz, speed from 10 to 50 mm/s, total Energy Density from 1.3 to 27 kW/cm²) and the thermal elevation during the experiment was recorded by a Fiber Bragg Grating (FBG) temperature sensor. Subsequently, the surface modifications were analysed by optical microscope, Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Results: With a Peak Power of 5 kW, RR of 20 kHz and speed of 50 mm/s, the microscopic observation of the irradiated surface showed increased roughness with small areas of melting and carbonization. EDS analysis revealed that, with these parameters, there are no evident differences between laser-processed samples and controls. Thermal elevation during laser irradiation ranged between 5 °C and 9 °C. Conclusions: 1070 nm fiber laser can be considered as a good device to increase the adhesion of Lithium di-silicate ceramics.

The use of optical fibers is increasing in modern aircraft because it helps solve challenges of size, weight, communication, and reliability in new aircraft generation. This work describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. It used off-the-shelf devices in the experiments, such as one 15-W semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETU), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver.

In this study, a carbon fiber microelectrode (CF) was applied for the investigation of electrochemical behavior and determination of natural antioxidant, apocynin (APO). Given the limited solubility of APO in water, a mixture of anhydrous acetic acid (AcH) with 20%, v/v acetonitrile (AN) and 0.1 mol L-1 sodium acetate (AcNa) was used. The electrochemical properties of APO were examined through linear sweep voltammetry (LSV), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The anodic oxidation of APO, which is the basis of the method used, proved to be diffusion-controlled and proceeded with a two-electron and one proton exchange. Both radicals and radical cations, arising from the first and second step of electrode reactions, respectively, underwent subsequent chemical transformations to yield more stable final products (EqCiEiCi mechanism). Using optimized DPV conditions, the anodic peak current of APO at potential of 0.925 V vs Ag/AgCl showed a good linear response within the concentration range of 2.7×10-6 – 2.6×10-4 mol L-1. The detection and quantification limits were determined as 8.9×10-7 and 2.7×10-6 mol L-1, respectively. The developed DPV method enabled the successful determination of APO in herbal extracts and in dietary supplements. It should be noted that this is the first method of voltammetric determination of APO.

In this study, different configurations based on linear fiber lasers were proposed and experimentally demonstrated to measure the concentration of paracetamol liquid solutions in a range of 52.61 to 201.33 g/kg. The optical gain was provided by a commercial bidirectional Erbium-Doped Fiber Amplifier (EDFA) and the linear cavity was obtained using two commercial Fiber Bragg Gratings (FBGs). The main difference of each configuration was the coupling ratio of the optical coupler used to extract the system signal. The sensing head corresponded to a Single-Mode Fiber (SMF) tip that worked as an intensity sensor. The results reveal that, despite the optical coupler used (50:50, 60:40, 70:30 or 80:20), all the configurations reached the laser condition, however, the concentration sensing was only possible using a laser drive current near to the threshold value. The configurations using a 70:30 and an 80:20 optical coupler allowed to perform paracetamol concentration measurements with a higher sensitivity of (-3.00±0.24) pW/(g/kg). In terms of resolution, the highest value obtained was 1.75 g/kg, when it was extracted 20% of the output power to the linear cavity fiber laser configuration.