Fiber-cement composites were prepared from cellulosic cotton residue (CCR) arise from sanding process (emerizing). The effect of different concentrations: 0.5% and 1%, and granulometry: thick (retained in a14 mesh sieve) and thin (retained in a 48 mesh sieve) of this residue were evaluated on tensile strength of cement slurries with seven (07) curing days. To characterize the CCR, TGA, FT-IR, SEM and XRD analysis were performed and the residue resistance in an alkaline environment was also evaluated. Splitting tensile strength test, known as Brazilian Test, was used to assess effects of the fibers on the mechanical behavior of cement matrix. Analyzing the results, the CCR proved to be resistant in an alkaline environment, meaning that it can withstand the alkaline environment of cement matrix. The results showed an improvement superior to 17% in tensile strength for 1% of CCR. Therefore, the CCR presents a great application potential in cement pastes used for oil well cementing that requires to increase its tensile strength, once a significant improvement was achieved with a low-residue employee.

Two new coordination compounds of Mn(II) and Cu(II) viz. [Mn(bz)2(Hdmpz)2(H2O)] (1) and [Cu(crot)2(Hdmpz)2] (2) (where, bz = benzoate, crot = crotonate, Hdmpz = 3, 5-dimethyl pyrazole) have been synthesized and characterized using single crystal X-ray diffraction technique, FT-IR, electronic spectroscopy, TGA and elemental analyses. Compounds 1 and 2 crystallize as mono-nuclear coordination compounds of Hdmpz based penta-coordinated Mn(II) and hexa-coordinated Cu(II) respectively containing distorted trigonal bipyramidal and distorted octahedral geome-tries. Crystal structure analysis of compound 1 reveals the presence C‒H⋯π and π-stacking in-teractions along with O‒H⋯O, N‒H⋯O and C‒H⋯O H-bonding interactions which stabilizes the layered assembly of the compound. Similarly, the presence of hydrogen bonding along with π-stacking interactions stabilizes the crystal structure of compound 2. We have carried out theo-retical investigations to analyze π⋯π H-bonding and antiparallel CH···π non-covalent interac-tions observed in the compounds. DFT calculations were performed to evaluate strength of these interactions energetically. Moreover, QTAIM and non-covalent interaction (NCI) plot index computational tool were used to characterize them and evaluate the contribution of the H-bonds.

Herein, we have reported the synthesis and characterization [single crystal X-ray diffraction technique, spectroscopic etc.] of two new Ni(II) and Zn(II) coordination compounds viz. [Ni(2,6-PDC)2]2[Ni(en)2(H2O)2]2[Ni(en)(H2O)4]·4H2O (1) and [Zn(2,6-PDC)(Hdmpz)2] (2) (where, 2,6-PDC = 2,6-pyridinedicarboxylate, en = ethylene-1,2-diamine, Hdmpz = 3,5-dimethyl pyrazole). Compound 1 is found to crystallize as a multicomponent Ni(II) compound with five discrete complex moieties; whereas, compound 2 is a mononuclear compound of Zn(II). Deep analysis of the crystal structure of compound 1 unfolds unusual dual enclathration of guest complex cationic moieties within the supramolecular host cavity stabilized by anion‒π, π-stacking, N‒H⋯O, C‒H⋯O and O‒H⋯O hydrogen bonding interactions. Interestingly, further enclathration of a complex cationic moiety is observed within another supramolecular host cavity formed involving anionic complex moieties and lattice water molecules in 1. Again, the crystal structure of compound 2 is stabilized by the presence of unconventional C‒H⋯π(chelate ring) interactions along with C‒H⋯O, C‒H⋯N hydrogen bonding, π-stacking, C‒H⋯π(pyridyl) interactions. These non-covalent interactions have been further studied theoretically using density functional theory (DFT) calculations, molecular electrostatic potential (MEP) surfaces, non-covalent interaction (NCI) plot index and quantum theory of atoms in molecules (QTAIM) computational tools. The computational study displays that π-stacking or H-bonds greatly tune the directionality of compound 1 although non-directional electrostatic forces dominate energetically. For compound 2, combined QTAIM/NCI plot analysis confirms the presence of unconventional C‒H⋯π(chelate ring) interaction along with other weak interactions obtained from the crystal structure analysis. Further, the individual energy contributions of these weak yet significant non-covalent interactions have also been determined computationally.

Today, there are commercially available high-performance electric wheelchairs, capa-ble of responding to strong limitations. However, despite these advancements, there is a significant portion of the population with severe disabilities who cannot access this mobility solution due to safety reasons. Indeed, either due to motor issues preventing reliable control of the wheelchair's commands, or associated visual or cognitive pathologies, the use of an electric wheelchair by these individuals would put them at risk and could also constitute a danger to those around them. This is why our research team is working on the development of augmented wheelchairs that allow a greater autonomy. We are mainly developing a system compatible with all electric wheel-chairs on the market, capable of making them anti-collision and anti-fall on uneven ground (sidewalks, stairs, etc.). In this article, we present our solution regarding the anti-collision function, in particular the sensors used to do this, as well as the strategy. We will focus on the shortcomings and weaknesses of various types of sensors and demonstrate how, by combining them in a certain way, we can develop a collision avoidance device capable of managing the diversity of everyday life situations. The two types of sensors that will be combined here are an in-house developed special near infrared sensor from the laboratory and a commercially available ultrasonic sensor. We will present the internal operation of the sensors, their limitations, experimental tests involving integration with the wheelchair, and the structure of the complete device.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

Cotton seeds as the main by-product of cotton are not only an important raw material for edible oil and feed but also a source of biofuel. The quality of cotton seeds directly affects cotton planting and is closely related to the yield and fiber quality. However, the molecular mechanism governing cotton seed size remains largely unexplored. This study investigates the regulatory mechanisms of cotton seed size by focusing on two cotton genotypes, N10 and N12, which exhibit notable phenotypic variations across multiple environments. Developing seeds were sampled at various stages (5, 20, 30, and 35 DAP) and subjected to RNA-seq. The temporal pattern clustering and WGCNA on differentially expressed genes identified 413 candidate genes, including these related to sugar metabolism that were significantly enriched in transcriptional regulation. A genetic transformation experiment indicated that the overexpression of the GhUXS5 gene encoding UDP-glucuronate decarboxylase 5 significantly increased seed size, suggesting an important role of GhUXS5 in regulating cotton seed size. This discovery provides crucial insights into the molecular mechanisms controlling cotton seed size, helping to unravel the complex regulatory network and offering new strategies and targets for cotton breeding to enhance the economic value of cotton seeds and overall cotton yield.

Two new Mn(II) and Zn(II) metal-organic compounds of 1,10-phenanthroline and methyl benzoates viz. [Mn(phen)2Cl2]2-ClBzH (1) and [Zn(4-MeBz)2(2-AmPy)2] (2) (where, 4-MeBz = 4-methylbenzoate, 2-AmPy = 2-aminopyridine, phen = 1,10-phenanthroline, 2-ClBzH = 2-chlorobenzoic acid) have been synthesized and characterized using elemental analysis, TGA, spectroscopic (FTIR, electronic) and single crystal X-ray diffraction techniques. Crystal structure analysis of the compounds reveals the presence of various non-covalent interactions which provides stability to the crystal structures. Crystal structure analysis of the compound 1 reveals the formation of supramolecular dimer of 2-ClBzH enclathrated within the hexameric host cavity formed by the neighboring monomeric units. Compound 2 is a mononuclear compound of Zn(II) where flexible binding topologies of 4-CH3Bz is observed with the metal centre. Moreover various non-covalent interactions such as lp(O)-π, lp(Cl)-π, C‒H∙∙∙Cl, π-stacking interactions as well as N‒H∙∙∙O, C‒H∙∙∙O and C‒H∙∙∙π hydrogen bonding interactions are found to be involved in plateauing the molecular self-association of the compounds. The remarkable enclathration of the H-bonded 2-ClBzH dimer into a supramolecular cavity formed by two [Mn(phen)2Cl2] complexes has been further studied theoretically using density functional theory (DFT) calculations, non-covalent interaction (NCI) plot index and quantum theory of atoms in molecules (QTAIM) computational tools. Synergistic effects have been also analysed using molecular electrostatic potential (MEP) surface analysis.

Cotton is the most ubiquitous and profitable fiber with diverse industrial and domestic applications. Grown in over 100 countries, it has a global market value of about $40 billion and employs over 350 million people from fields to textile mills, contributing about 7% of total labor-force recruitment in developing economies. Cotton has an indeterminate growth habit and an extensive tap root system affected by soil physicochemical and environmental conditions. There is a consensus among experts that conventional cotton cultivation still has a long way to attain sustainability, which is essential if cotton will maintain its competitive edge over other natural and synthetic fibers like hemp, polyesters, and rayon. Despite several efforts already committed to growing cotton sustainably, sustainability has eluded cotton cultivation globally because of the intense farm inputs (freshwater, pesticides, and heavy-duty equipment) needs, especially in developing economies. Some of the technological advancements towards achieving the goal of sustainable cotton cultivation include the development of new varieties, improved irrigation and mulching and precision agriculture techniques, application of remote sensing and Unmanned Aerial Systems (UAS) combined with image processing, and the introduction of autonomous and multi-purpose robotic platforms for growing and harvesting cotton. This review attempts to evaluate the successes already achieved by stakeholders in moving cotton towards sustainable production and identify areas where efforts are still needed to reach sustainable production and improved profitability goals for cotton with projections for future research directions.

Climate change has resulted in increased incidences of abiotic stresses, such as heat, drought, salinity, and waterlogging. These stressors have a negative impact on the cotton (Gossypium hirsutum L.) crop and cause significant yield losses. Each stressor induces specific physiological and metabolic alterations interconnected with the complex changes at molecular levels. Understanding the molecular pathways that govern the cotton plant's stress responses is crucial to develop stress-tolerant cotton cultivars that can withstand different stresses. Molecular investigations have mapped the changes in the expression of stress-responsive genes, encompassing heat shock proteins and ion transporters, which play a vital role in facilitating adaptive responses. These approaches have been shown to help identify dynamic gene expression patterns and elucidate intricate regulatory networks using advanced metagenomics and multi-omics techniques. By leveraging genetic diversity and utilizing advanced molecular methods, it would be possible to develop stress-resilient cotton varieties to ensure sustainable cotton production in the face of abiotic stresses. This review provides an overview of the effects of various abiotic stressors on cotton plants, including drought, salt, heat, and waterlogged soil. We also explore the extensive network of stress-responsive genes, proteins, and signaling pathways in cotton by summarizing the studies on gene expression regulation, proteins involved in stress response, and biochemical characteristics.

Online digital mental health communities can contribute to users’ mental health positively and negatively. Yet the measurement of outcomes and impact relating to digital mental health communities is difficult to capture. In this paper we demonstrate the development of an online experience measure for a specific children and young people’s community inside a digital mental health service. The development is informed by three phases: (i) item reduction through Estimate-Talk-Estimate modified Delphi methods, (ii) user testing with participatory action research and (iii) a pilot within the digital service community to explore its use. Rounds of experts talks help to reduce the items. User experience workshops helped to inform the usability and appearance, wording, and purpose of the measure. Finally, the pilot results highlight completion rates, difference in scores for age and community roles and a preference to ‘relate to others’; as a mechanism of support. Outcomes frequently selected in the measure show the importance of certain aspects of the community, such as safety, connection, and non-judgment previously highlighted in the literature. Self-reported helpfulness scales like this one could be used as indicators of meaningful engagement within the community and its content but further research is required to ascertain its acceptability and validity. Phased approaches involving stakeholders and participatory action research enhances the development of digitally enabled measurement tools.

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

This literature review provides an in-depth exploration of the research conducted on the investigation and measurement of residual stress (RS) in Wire Arc Additive Manufacturing (WAAM) products, particularly focusing on how process parameters influence the phenomenon. RS plays a crucial role in determining the mechanical behavior and structural integrity of WAAM components. This review article gives an understanding of the relationship between process parameters and RS to optimize the WAAM processes and ensure the durability of the final products. It also summarizes key findings, measurement techniques, challenges, and future directions in this evolving field. The review also analyzes a measurement of RS in the products of WAAM as a function of process parameters depending on examining various research studies, techniques, and methodologies employed in their studies. Experimental measuring techniques and numerical analysis of RS to determine the impacts of RS in mechanical response in products of WAAM were discussed. By offering a comprehensive overview of current research trends and insights, this review serves as a valuable resource to guide future investigations, fostering the advancement of WAAM as a robust and efficient manufacturing technology.

With the development of deep learning, the Super-Resolution (SR) reconstruction of microscopic images has improved significantly. However, the scarcity of microscopic images for training, the underutilization of hierarchical features in original Low Resolution (LR) images, and the high-frequency noise unrelated with the image structure generated during reconstruction process are still challenges in the Single Image Super-Resolution (SISR) field. Faced with these issues, we first collected sufficient microscopic images through Motic, a company engaged in the design and production of optical and digital microscopes, to establish a dataset. Secondly, we proposed a Residual Dense Attention Generative Adversarial Network (RDAGAN). The network comprises a generator, an image discriminator, and a feature discriminator. The generator includes a Residual Dense Block (RDB) and a Convolutional Block Attention Module (CBAM), focusing on extracting the hierarchical features of the original LR image. Simultaneously, the added feature discriminator enables the network to generate high-frequency features pertinent to the image’s structure. Finally, we conducted experimental analysis and compared our model with six classic models. Compared with the best model, our model improved PSNR and SSIM by about 1.5dB and 0.2, respectively.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Musical instrument recognition is a relatively unexplored area of machine learning due to the need to analyze complex spatial-temporal audio features. Traditional methods using individual spectrograms, like STFT, Log-Mel, and MFCC, often miss the full range of features. We propose a hierarchical residual attention network using a scaled combination of multiple spectrograms, including STFT, Log-Mel, MFCC, and CST features (chroma, spectral contrast, and Tonnetz), to create a comprehensive sound representation. This model enhances focus on relevant spectrogram parts through attention mechanisms. Experimental results with the OpenMIC-2018 dataset show significant improvement in classification accuracy, especially with the "Magnified 1/4 Size" configuration. Future work will optimize CST feature scaling, explore advanced attention mechanisms, and apply the model to other audio tasks to assess its generalizability.

The peculiar physicochemical features of deep eutectic solvents (DESs), in particular their tunability, make them ideal media for various applications. Despite their ability to solubilize metal oxides, their use as rust removers from valuable substrates has not yet been thoroughly investigated. In this study we chosen three known DESs, consisting of choline chloride and acetic, oxalic or citric acid for evaluating their ability to remove corrosion products from a cellulose-based material as linen fabric and two different lithotypes, as travertine and granite. The artificial staining was achieved by placing a rusty iron grid on their surfaces. The DESs were applied by means of cellulose poultice on the linen fabrics, while on the rusted stone surfaces with a cotton swab. Macro- and microscopic observations, colorimetry and SEM/EDS analysis were employed to ascertain the cleaning effectiveness and the absence of side effects on the samples after treatment. Oxalic acid-based DES was capable of removing rust stains from both stone and cellulose-based samples, while choline chloride/citric acid DES was effective only on stone specimens. The results suggest a new practical application of DESs for the elimination of rust from lithic and cellulosic substrates of precious and artistic value.

In recent decade water pollution by micropollutants is an increasing environmental concern. Since 2019, due to COVID-19 pandemic, increased stormwater pollution by chlorine based disinfectants has been determined. Research aimed to treat of chlorine contaminated stormwater after outdoors spaces disinfection are very limited. Runoff from disinfected areas and residual chlorine present in stormwater are transported to surface water bodies. Residual chlorine reacts with dissolved organic compounds in water and results the formation of environmentally toxic disinfection by-products. Studies present event low residual chlorine concentrations may pose a risk to aquatic flora and fauna. In this study the efficiency of different filter materials, including peat, wood chips, sawdust (column tests) and ceramzites Leca, Pollytag, Polski, Ceski (batch tests), in retaining residual chlorine were tested in laboratory scale batch and flow through experiment. The best efficiency to retain chlorine presented sawdust (96 %) and ceramzite Leca (76 %). The plants abilities to reduce pollution by chlorine was analyzed in raised garden bed. Research results will contribute to future studies aimed to retain various micropollutants in stormwater using remediation technologies.

High hopes were associated with the new anti-angiogenic medicament, bevacizumab, which due to the possibility of binding to isoform A of vascular endothelial growth factor (VEGF), inhibited the creation of new blood vessels. However, not only blood vessels are responsible for the tumor cells' spread. During the process of tumor growth, lymphangiogenesis is mediated by other isoforms of the VEGF family, specifically VEGF-C and VEGF-D, which are independent of the bevacizumab action. Therefore, based on the mechanism of bevacizumab action and the processes of angio- and lymphangiogenesis, we formed three hypotheses: 1) if the lymph nodes in the primary ovarian cancers are metastatic, the outcome of bevacizumab treatment is worsened; 2) concerning the second-line treatment, bevacizumab will act in a weakened manner if the recurrence occurs in lymph nodes compared to local recurrences; 3) patients treated by bevacizumab are more likely to have recurrences in lymph nodes. These hypotheses raise the issue of the existing gap of knowledge, which concerns the effect of bevacizumab on the metastatic lymph nodes.

Vibration problems have become one of the most important factors affecting robot performance. To this end, a terminal residual vibration suppression method based on joint trajectory optimization is proposed to improve the accuracy and stability of robot motion. Firstly, based on the characteristics of the friction nonlinearity due to joint coupling and physical feasibility of dynamic parameters, a semidefinite programming method is used to identify dynamic parameters with actual physical meaning, thereby obtaining an accurate dynamic model. Then, based on the result of the residual vibration time domain analysis, a joint trajectory optimization model with the goal of minimizing joint tracking error is established. The Chebyshev collocation method is used to discretize the optimization model. The dynamic model is used as the optimization constraint, and barycentric interpolation is used to obtain the optimized joint motion trajectory. Finally, industrial robot experiments prove that the vibration suppression method proposed in this article can reduce the maximum acceleration amplitude of residual vibration by 62% and the vibration duration by 71%. Compared with the input shaping method, the method proposed in this paper can reduce the terminal residual vibration more effectively and ensure the consistency of running time and trajectory.

Aiming at the problems of high cost of manual pulling, low reliability of existing pulling devices, high breaking rate and high leakage rate in the process of cotton stalk reuse after leaving the field in Xinjiang cotton area, a loosening soil and root-cutting cotton stalk pulling the setting machine has been researched and designed, established the root-cutting force model, calculated and optimized the key parameters of the V-shaped root-cutting knife, and determined the range of slide cutting angle, cutting edge angle and soil entry angle. The shoveling process simulation of V-shaped root-cutting knife and root-soil complex was constructed, and the working mechanism of V-shaped root-cutting knife was clarified. In order to verify the reliability and operation performance of the V-shaped root-cutting knife, the slide cutting angle, cutting edge angle and soil entry angle were used as the test factors, the response surface test of three-factors and three-levels was carried out with root-breaking force and mean value of the cutting resistance as the test index. The test results were analyzed by variance analysis, the significant of influencing factors on the root-breaking force are in a descending order as: slide cutting angle, cutting edge angle, soil entry angle; the degree of influence on the mean value of the cutting resistance are as follows: slide cutting angle, soil entry angle, cutting edge angle. In order to make the V-shaped root-cutting knife achieve the optimal working state, the parameters of the test index were optimized, and the optimal design parameters of the V-shaped root-cutting knife were set as follows: the slide cutting angle was 48.3°, cutting edge angle was 43.4°, and soil entry angle was 26.2°. The field uprooting test showed that the average pass rate of root breakage was 94.8% and the average pull-out rate of the cotton stalk was 93.2%. This study provides theoretical guidance for the development of root breaking mechanism of cotton straw harvester.

In the recent years, tissue engineering researchers have exploited a variety of biomaterials that can potentially mimic extracellular matrix (ECM) for tissue regeneration. Natural cellulose, mainly obtained from bacterial (BC) and plant-based (PC) sources, can serve as a high potential scaffold material for different regenerative purposes. Natural cellulose has drawn the attention of researchers due to its advantage over synthetic cellulose in terms of availability, cost-effectiveness, perfusablility, biocompatibility, negligible toxicity, mild immune response and due to imitating native tissues. In this article, we will review the recent in vivo and in vitro studies aimed to assess the potentials of natural cellulose for the purpose of soft (skin, heart, veins, nerve, among others) and hard (bone and tooth) tissue engineering.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

The adoption of digital health technologies accelerated during Covid-19, with concerns over the equity of access due to digital exclusion. Using data from a text-based online mental health service for children and young people we explore the impact of the pandemic on service access and presenting concerns and whether differences were observed by sociodemographic characteristics in terms of access (gender, ethnicity and deprivation). We used interrupted time-series models to assess whether there was a change in the level and rate of service use during the Covid-19 pandemic (April 2020-April 2021) compared to pre-pandemic trends (June 2019-March 2020). Routinely collected data from 61221 service users were extracted for observation, those represented half of the service population as only those with consent to share their data were used. The majority of users identified as female (74%) and White (80%), with an age range between 13 and 20 years of age,. There was evidence of a sudden increase (13%) in service access at the start of the pandemic (RR 1.13 95% CI 1.02, 1.25), followed by a reduced rate (from 25% to 21%) of engagement during the pandemic compared to pre-pandemic trends (RR 0.97 95% CI 0.95,0.98). There was a sudden increase in almost all presenting issues apart from physical complaints. There was evidence of a step increase in the number of contacts for Black/African/Caribbean/Black British (38% increase; 95% CI: 1%-90%) and White ethnic groups (14% increase; 95% CI: 2%-27%) ), the sudden increase in service use at the start of the pandemic for the most (58% increase; 95% CI: 1%-247%) and least (47% increase; 95% CI: 6%-204%) deprived areas. During the pandemic, contact rates decreased, and referral sources change at the start. Findings on access and service activity align with other studies observing reduced service utilisation. The lack of differences in deprivation levels and ethnicity at lockdown suggests exploring equity of access to the anonymous service. The study provides unique insights into changes in digital mental health use during Covid-19 in the UK.

This study presents the Distilled MixUp Squeeze ResNet (DMSResNet), an optimized variant of the Residual Network architecture designed for high accuracy and computational efficiency. By integrating Squeeze-and-Excitation blocks, MixUp data augmentation, and knowledge distillation, it achieves competitive performance within strict parameter constraints and limited training resources. Evaluated on the CIFAR-10 dataset, the model attains a 96.56% accuracy with only 4.3 million total parameters. The results demonstrate that optimization of established architectures can yield performance comparable to newer models, especially in resource-limited scenarios. This work contributes to the development of efficient deep learning models for applications in constrained computational environments.

We investigate some information properties of consecutive k-out-of-n:G systems in light of fractional generalized cumulative residual entropy. We firstly derive a formula to compute fractional generalized cumulative residual entropy related to the system's lifetime and explore its preservation properties in terms of established stochastic orders. Additionally, we obtain useful bounds. To aid practical applications, we propose two non parametric estimators for the fractional generalized cumulative residual entropy in these systems. The efficiency and performance of these estimators are illustrated using simulated and real datasets.

Crop yield estimation supported by satellite remote sensing data can provide expeditious and strategic information for farmers’ decision-making. Most recent forecasting methods have indicated a promising pathway based on machine learning algorithms. However, validation performances, demand for big data and their inherent inexplicability have not yet consolidated a substantial differential to replace methods based on simpler and more understandable models. This paper proposes an approach based on simple linear models fitted from vegetation indices (VIs) assessed at regular intervals of time series derived from MODIS satellite images, aiming to forecast cotton yields in representative areas of the Brazilian Cerrado. Data from 281 commercial production plots were taken to train (167 plots) and test (114 plots) linear regression models relating seed cotton yield and nine well-known VIs averaged in 15-days intervals. Among the evaluated VIs, EVI (Enhanced Vegetation Index) and TVI (Triangular Vegetation Index) showed the lowest root mean square errors (RMSE) and the highest determination coefficients. The best periods for in-season yield prediction were from the 90-105 to 135-150 days after sowing (DAS), i.e. phenological phases corresponding to boll development, open boll and fiber maturation, with lowest RMSE of about 750 kg ha-1 and R2=0.70. The best forecasts for early crop stages were provided by models at the peaks (maximum value of the VI time-series) for EVI and TVI, which occurred around 80-90 DAS. The proposed approach makes the yield predictability more inferable along the crop time series just by providing sowing dates, contour maps and its respective VIs.

Outliers seriously affect the accuracy in geometric model fitting. Previous works in coping with outliers involve threshold selection and scale estimation. However most scale estimators suppose the inlier distribution as a Gaussian model, which usually poorly meets the cases in geometric model fitting. Outliers, considered as the points with big residuals to all the true models, share common items with big values in quantized residual preferences, thus making the outliers gather away from the inliers in quantized residual preference space. In this paper we make use of this outlier consensus in quantized residual preference space by extending the usage of energy minimization to combine the model error and the spatial smoothness in quantized residual preference space for outlier detection. The energy minimization based outlier detection process follows an alternate sampling and labeling framework. After the outlier detection, an ordinary energy minimization method is employed to optimize the inlier labels, which also follows the framework of alternate sampling and labeling. The experimental results in this study show that the energy minimization based outlier detection method can detect most of the outliers in the data. Furthermore, the proposed energy minimization based inlier segmentation process segments the inliers into different models quite accurately. Overall, the performance of the proposed method is better than most of the state-of-the-art methods.

The graphene based highly conductive and flexible devices has received momentous attraction and growth in recent years for potential multifunctional uses. The development of flexible and washable textile sensors, actuators, energy storage and energy harvesting systems. Textile fabrics coated with graphene and conductive polymers have been used for wearable self-powered e-textiles, such as tribo-electric, piezoelectric, and Thermoelectric. Herein this research, 100% woven cotton fabric is Fictionalized with graphene oxide (GO) using industrial-scale cold pad batch dyeing technique for the development of low-grade body heat into self-powered wearable e-textiles. The conductive polymer PEDOT: PSS was coated using layer by layer approach. The study demonstrates that the resultant textile electrodes showed reduced electrical sheet resistance from 2.5 MΩ to 15KΩ, with a reduced graphene oxide and further reduced to (2.5 -12.5 Ω) for conductive polymer. The sheet resistance was decreased with the number of dyeing cycles (10-15) and increased with 20 washing cycles vice versa. The study demonstrates that the sensor response and performance were improved with increasing the content percent of rGO and PEDOT: PSS. The tensile strength of as coated fabric electrodes was improved from (25.0-85.5 mPa) and fabric thickness was increased to (26-38µm) without compromising or influencing the air permeability. The resultant textile electrodes may potentially be used in smart textiles for self-powered flexible wearable generators, sensors, and energy storage. The study demonstrates that the cold pad batch dyeing method is a suitable and effective method for the fabrication of graphene-based textiles.

Cotton leaf curl Kokhran virus (CLCuKoV) (genus, Begomovirus; family, Geminiviridae) is highly infectious, widespread and the most dangerous pathogen of cotton (Gossypium hirsutum L.) that is responsible to a serious disorder, cotton leaf curl disease (CLCuD). Begomoviruses are spread very efficiently by the whitefly Bemisia tabaci cryptic species, causing economic losses to cotton crop, all over the world. The ‘Lucknow’ strain of CLCuKoV has emerged as a divergent isolate that could cause CLCuD. The monopartite ssDNA genome of CLCuKoV-Lu (2.7 Kb) contains six open reading frames (ORFs) that was shown to encode four major proteins. RNA interference (RNAi)-based antiviral innate immunity is a sequence-specific biological phenomenon and a powerful tool to control plant viruses. The present study aims to determine cotton locus-derived microRNAs (ghr-miRNAs) that are identified for targeting the CLCuKoV-Lu ss-DNA-encoded mRNAs using a predictive approach that involves four computational algorithms, miRanda, RNA22, psRNATarget and RNAhybrid. Mature ghr-miRNA sequences (n=80) from allotetraploid upland cotton (2n = 4x = 52) were selected from the miRBase and were tested for alignment with the CLCuKoV-Lu genome. Among the 80 cotton locus-derived ghr-miRNAs evaluated, only one consensus cotton locus-derived ghr-miRNA (ghr-miR2950) was concluded to have effective ghr-miRNA target site at common nucleotide position 82 in the CLCuKoV-Lu genome respectively, using a stringent criterion, identified by all the algorithms used. The miRNA targeting is reliant on base pairing of miRNA-mRNA target pairings. Conservation of the hybridization binding site of the predicted ghr-miR2950 was validated using multiple sequence alignment within all the strains of CLCuKoV. We constructed a regulatory interaction network of miRNA–mRNA to identify novel targets. The efficacy of the predicted miRNAs against CLCuKoV-Lu was evaluated by RNAi-mediated targeted mRNA cleavage. The current investigated miRNA targets provide evidence for the development of CLCuD-resistant cotton plants.

Composites with HDPE and PLA matrix have been tested to analyse the effect of natural fillers (wood flour, recycled waste paper and a mix of both fillers) and temperature on polymer degradation. Composting tests have been performed in both mesophilic (35°C) and thermophilic (58°C) conditions. Degradation development has been evaluated through mass variation, TGA and DSC. HDPE, as expected, did not display any relevant variation, confirming its stability under our composting conditions. PLA is sensibly influenced by temperature and humidity, with higher reduction of Mw when composting is performed at 58°C. Natural fillers seem to influence degradation process of composites, already at 35°C. In fact, degradation of fillers at 35°C allows a mass reduction during composting of composites, while neat PLA do not display any variation.

Sulfite and kraft pulping are two principal methods of industrial delignification of wood. In recent decades, those have been considered as possibilities to pretreat recalcitrant wood lignocellulosics for enzymatic hydrolysis of polysaccharides and subsequent fermentation of obtained sugars to valuable bioproducts. Current work compares chemistry and technological features of two different cooking processes in the preparation of polysaccharide substrates for deep sacchari-fication with P. verruculosum glycosyl hydrolases. Bleached kraft and sulfite pulps were subjected to hydrolysis with enzyme mixture of high xylanase, cellobiohydrolase and β-glucosidase activities at a dosage of 10 FPU/g of dry pulp and fiber concentration of 2.5, 5 and 10%. HPLC was used to analyze soluble sugars after hydrolysis and additional acid inversion of oligomers to monosaccharides. Kraft pulp demonstrated higher pulp conversion after 48 h (74-99%), mostly resulted from deep xylan hydrolysis. Sulfite-pulp hydrolysates, obtained in similar conditions, due to higher hexose concentration (more than 50 g/L), had higher fermentability for industrial strains producing alcohols, microbial protein or organic acids. Along with saccharification, enzymatic modification of non-hydrolysed residues occurred, which led to decreased degree of polymerization and composition changes in two industrial pulps. As a result, crystallinity of kraft pulp increased by 1.3%, which opens possibilities for obtaining new types of cellulosic products in pulp and paper industry. The high adaptability and controllability of enzymatic and fermentation processes creates prospects for the modernization of existing factories.

Cholesterol homeostasis is pivotal for cellular function. Acyl-coenzyme A:cholesterol acyltransferase 1 (ACAT1), also abbreviated as SOAT1, is an enzyme catalyzing the storage of excess cholesterol to cholesteryl esters. ACAT1 is an emerging target to treat diverse diseases including atherosclerosis, cancer, and neurodegenerative diseases. F12511 is a high affinity ACAT1 inhibitor. Previously, we developed a stealth liposome-based nanoparticle to encapsulate F12511 to enhance its delivery to the brain and showed its efficacy in treating a mouse model for Alzheimer’s disease (AD). In this study, we introduce F26, a close derivative of F12511 metabolite in rats. F26 was encapsulated in the same DSPE-PEG2000/phosphatidylcholine (PC) liposome-based nanoparticle system. We employed various in vitro and in vivo methodologies to assess F26's efficacy and toxicity compared to F12511. Results demonstrate that F26 is more effective and durable than F12511 in inhibiting ACAT1, in both mouse embryonic fibroblasts (MEFs) and in multiple mouse tissues including the brain tissues, without exhibiting any overt systemic or neurotoxic effects. This study demonstrates the superior pharmacokinetic and safety profile of F26 in wild-type mice, and suggests its therapeutic potential against various neurodegenerative diseases including AD.

Cotton fiber is the leading natural textile material, and fiber elongation plays an essential role in the formation of cotton yield and quality. Although a wealth of components in the molecular network controlling cotton fiber elongation have been reported, a lot of players still need to be functionally dissected to understand the regulatory mechanism of fiber elongation comprehensively. In the present study, an R2R3-MYB transcription factor gene, GhMYB201, was characterized and functionally verified via CRISPR/Cas9 mediated gene editing. GhMYB201 was homologous to Arabidopsis AtMYB60, and both coding genes (GhMYB201At and Dt) were preferentially expressed in elongating cotton fibers. Knocking-out of GhMYB201 significantly reduced the rate and duration of fiber elongation, resulting in shorter and coarser mature fibers. It was found that GhMYB201 could bind and activate the transcription of cell wall loosening genes (GhRDLs), and also β-ketoacyl-CoA synthase (GhKCSs) genes to enhance very-long-chain fatty acid (VLCFA) levels in elongating fibers. Taken together, our data demonstrated that the transcription factor GhMYB201s play essential roles in promoting fiber elongation via activating genes related to cell wall loosening and VLCFA biosynthesis.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Cytochrome P450 (CYPs) is a functionally diversified third-largest gene family that exploded in the plant kingdom. Their role in different organ development has been illustrated by the intervention of phytohormone. Cotton is a model organism for cell differentiation and cell elongation. To decipher the participation of CYPs in different cotton fiber developmental stages, we identified and characterized 2460 CYPs in three diploids and two allotetraploid cottons. Furthermore, In-silico expression and cluster analysis of cotton CYPs was conducted to distinguish the fiber stage-specific clusters that have the determining role in different stages of fiber development. The subgenome expression of two conserved Gossypium hirsutum CYPs, namely, GhCYP78A197 and GhCYP78A198 contributed to fiber initiation at an early stage of fiber development, governed by the co-occurrence of TATA and MYB TFs binding sites. Coexpression network partners of these two GhCYP78A annotated as auxin, kinases, chromatin remodeler, epigenetic regulator and cyclin-related genes that possibly induce the endoreduplication and cell proliferation for fiber cell initiation to define the high yield and biomass.

Cotton fiber, a crucial and sustainable resource for global textile production, undergoes a complex five-stage developmental process, encompassing initiation, elongation, transition, secondary cell wall biosynthesis, and maturation. These elongated single-cell fibers originate from the outer ovule epidermis. The development of cotton fibers involves intricate changes in gene expression and physiological processes, resulting in a nearly pure cellulose product vital for the global cotton industry. Decoding genes associated with fiber development enhances our understanding of cotton fiber mechanisms and facilitates the cultivation of varieties with enhanced quality. In recent decades, advanced omics approaches, including genomics, transcriptomics, and proteomics, have played a pivotal role in identifying genes and gene products linked to cotton fiber development, including the MYB transcription factor family which coordinates cotton fiber development. Molecular studies have revealed transcription factors like MYB, WRKY, Homeodomain Leucine Zipper (HD-ZIP) and basic Helix-Loop-Helix (bHLH) influencing fiber initiation and elongation. The intricate interplay of phytohormones like auxin, gibberellic acid (GA), brassinosteroid (BR), jasmonic acid (JA), ethylene, abscisic acid (ABA), and cytokinin is explored, providing a comprehensive perspective on shaping cotton fibers. Numerous candidate genes and cellular processes affecting various aspects of fiber development hold promise for genetic engineering or marker-assisted breeding to improve fiber quality. This review presents a comprehensive overview of key achievements in cotton molecular biology, with a specific emphasis on recent advancements in understanding transcription factors and phytohormones involved in cotton fiber initiation and elongation.

There is a need for versatile in vivo nuclear imaging reporter systems to foster preclinical and clinical research. We explore the applicability of the SNAPTag and novel radiolabeled small-molecule ligands as a versatile reporter gene system for in vivo nuclear imaging. SNAPTag is a high-affinity protein tag used in a variety of biochemical research areas and based on the suicide DNA repair enzyme O6-methylguanine methyl transferase (MGMT). Its ligands are well suited for reporter gene imaging as the benzyl guanine core scaffold can be derivatized with fluorescent or radiolabeled moieties for various applications. Three guanine-based SNAPTag ligands ([18F]FBBG, [18F]pFBG and [18F]mFBG) were synthesized in high yields and were (radio)chemically characterized. HEK293 cells were engineered to express the SNAPTag on the cell surface and served as cell model to assess target affinity by radiotracer uptake assays, Western blotting and SDS-PAGE autoradiography. A subcutaneous HEK293-SNAPTag xenograft model in immunodeficient mice was used for in vivo evaluation of [18F]FBBG amd [18F]pFBG while the biodistribution of [18F]mFBG was characterized in naïve animals. The results were validated by ex vivo biodistribution studies and immunofluorescence staining of the xenografts. All three radiotracers were produced in high radiochemical purity, molar activity and good yields. Western blot analysis revealed successful SNAPTag expression by the transfected HEK293 cells. In vitro testing revealed high target affinity of all three tracers with an up to 191-fold higher signal in the HEK293-SNAPTag cells compared to untransfected cells. This was further supported by a prominent radioactive protein band at the expected size in the SDS-PAGE autoradiograph of cells incubated with [18F]FBBG or [18F]pFBG. The in vivo studies demonstrated high uptake in HEK293-SNAP xenografts compared to HEK293 xenografts with excellent tumor-to-muscle ratios (7.5 ± 4.2 for [18F]FBBG and 10.6 ± 6.2 for [18F]pFBG). In contrast to [18F]pFBG and its chemical analogue [18F]mFBG, [18F]FBBG showed no signs of unspecific bone uptake and defluorination in vivo. Radiolabeled SNAPTag ligands bear great potential for clinical applications such as in vivo tracking of cell populations, antibody fragments and targeted radiotherapy. With excellent target affinity, good stability, and low non-specific binding, [18F]FBBG is a highly promising candidate for further preclinical evaluation.

This paper presents geometric analyses of welded frames after free relaxing and vibratory stress relief (VSR). Respected frames were tested components of a prototype packaging machine. Two types of relaxation were carried out to remove stresses introduced as a result of welding process. One of the frame was subjected to free relaxing, while the other one to accelerated vibration relaxing. Detection of the frame geometry changes was performed using a photogrammetric system. In addition, an evaluation of the geometry change was conducted for fifteen variants of steel frame support. A comparative analysis of the geometric deviations of the frames after free and vibratory stress relief confirmed the assumption that the frame after vibration stress relief better reproduces the nominal dimensions. Nevertheless, it should be emphasized that after vibratory stress relief the frame is not subject to further deformation, which is a desirable effect. In the case of free relaxing, the frame undergoes dimensional changes in a random manner. In summary, carrying out accelerated vibratory stress relief allows control of spontaneous dimensional changes in the designed frame of a packaging machine resulting from spontaneous relaxation of stresses arising from the welding process. The shortening of the relaxation process of the welded frame is also an unquestionable advantage.

Recently, there has been growing interest in alternative measures of uncertainty, including cumulative residual entropy. In this paper, we consider a mixed system consisting of n components, assuming that all components are operational at time t. We use the system signature to calculate the cumulative residual entropy of the mixed system’s remaining lifetime. This measure is a useful criterion for assessing the predictability of a system’s lifetime. We study several results related to the cumulative residual entropy of mixed systems, including expressions, limits, and order properties. These results shed light on the behavior of the measure and provide insights into the predictability of mixed systems. In addition, we propose a criterion for selecting a preferred system based on the relative residual cumulative entropy. This criterion is closely related to the parallel system and provides a practical way to choose the best system configuration. Overall, the present study of cumulative residual entropy and the proposed selection criterion provide valuable insights into the predictability of mixed systems and can be applied in various fields.

Usually, the two-bath dyeing process using disperse dyes and reactive dyes separately was employed for the dyeing of PC blends. The cost of the double bath, dyeing cycle, energy consumption and chemical consumption is quite higher than the one-step or single bath dyeing methods. In this study, the one-bath dyeing process using one kind of dye was investigated. Polyester cotton blends dyed in one-bath one-step dyeing methods with disperse dye after surface modifications of cotton by acetylation methods were studied. Surface modification of cotton was carried out using fibrous acetylation methods. The effect of acetic anhydride and time on percent acetyl content at room temperature was studied. Modified polyester/cotton was carried out in HTHP dyeing machine incorporates with different dye concentrations and dyeing temperature. Surface chemistry, thermal decomposition property and moisture regain of modified polyester/ cotton blend are evaluated. The color strength of the dyed fabrics and their fastness properties to washing, light, and rubbing as well as tear strength and abrasion resistance were evaluated. The effect of dye concentration and temperature color strength, tensile strength warp and weft direction was assessed. The optimum value for surface modification was obtained with a concentration of acetylation agent 16% and time of reaction 2.5 hours, gave percent acetylation of 34. An FTIR spectrum shows acetylation resonance. The experiment result of dyeing showed that the optimum value was obtained with dye concentration above 1% at a temperature of 120oC, warp tensile strength decreased by 12% and weft tensile strength was decreased by 9% from the control half-bleached fabric. Results of this study showed that a one-step one-bath dyed modified polyester/cotton blend with disperse dye fabric presents good fastness property compared with conventional two-bath dyed fabric as well as colour strength values.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

Verticillium wilt is a soil borne disease caused by distinct vegetative compatibility groups (VCG) of the fungus Verticillium dahliae. Two V. dahliae isolates were recovered from symptomatic cot-ton plants in Australian cotton fields and were assigned to two distinct vegetative compatibility groups (VCGs). One corresponding to the defoliating (VCG 1A) and the other non-defoliating (VCG 2A) pathotypes of Verticillium, have been transformed with Red and Green Fluorescent protein genes, respectively. The transformants maintained their ability to infect cotton and both strains were observed to colonise the xylem vessels of cotton plants. Moreover, we observed that the cotton V. dahliae strains could also infect some sampled non-Gossypium species found in the Australian landscape. The fluorescently labelled strains of V. dahliae will allow us to gain a thorough understanding of the infection processes of this important pathogen.

Egyptian cotton is one of the most important commodities to the Egyptian economy and is renowned globally for its quality, which is currently graded by manual inspection. This has several drawbacks including significant labour requirement, low inspection efficiency, and influence from inspection conditions such as light and human subjectivity. This current work uses a low-cost colour vision system, combined with machine learning to predict the cotton lint grade of the cultivars Giza 86, 97, 90, 94 and 96. Unsupervised and supervised machine learning approaches were explored and compared. Three different supervised learning algorithms were evaluated: linear discriminant analysis, decision trees and ensemble modelling. The highest accuracy models (77.3-98.2%) used an ensemble modelling technique to classify samples within the Egyptian cotton grades: Fully Good, Good, Fully Good Fair, Good Fair and Fully Fair. The unsupervised learning technique k-means showed that human error is more likely to occur when classifying lint belonging to the higher quality grades and underlined the need for an intelligent system to replace manual inspection.

The epidermal cells on the surface of the cotton ovules undergo differentiation to produce fibers, which are single-celled hair-like protrusions resembling the plant trichomes. The initiation of these unicellular fibers from the cotton ovule surface is a complex and tightly regulated process. The initiation step is the cell fate-determining stage, which leads to the commitment of cells that eventually developed into fibers, thus becomes the most crucial phase in fiber development. The in-depth knowledge of molecular regulation is a prerequisite to get a clear view of the fiber initiation process's genetic and epigenetic control. The identification and functional validation of cotton fiber initiation-related genes, few fibreless mutants, transcription factors, microRNAs, epigenetic regulators, as well as the elucidation of the role of phytohormones as signaling molecules, has played a significant role in understanding the cotton fiber initiation process at the molecular level. This review focuses on the comprehensive information regarding the genetic and epigenetic regulation of cotton fiber initiation. Thus, the review will provide readers insight into mechanistic details that operate during cotton fiber initiation.

Surface area and pore size distribution of Eucalyptus samples pretreated by different methods were determined by the Brunauer-Emmett-Teller (BET) technique. Three methods were applied to prepare cellulosic biomass samples for BET measurements: air, freeze, and critical point drying (CPD). Air and freeze drying caused severe collapse of biomass pore structures, but CPD effectively preserved biomass morphology. Surface area of CPD prepared Eucalyptus samples was determined to be 58–161 m2/g, whereas air and freeze dried samples were 0.5–1.3 and 1.0–2.4 m2/g, respectively. Average pore diameter of CPD prepared Eucalyptus samples were 61–70Å. CPD preserved Eucalyptus sample morphology by replacing water with a non-polar solvent, CO2 fluid, which prevented hydrogen bond reformation in the cellulose.

Cotton (Gossypium spp.) is the most important fibre crop worldwide. Black root rot and Fusarium wilt are two major diseases of cotton caused by soil-borne Berkeleyomyces rouxiae and Fusarium oxysporum f. sp. vasinfectum (Fov), respectively. Phenotyping plant symptoms caused by soil-borne pathogens has always been a challenge. To increase the uniformity of infection, we adapted a seedling screening method that directly uses liquid cultures to inoculate the plant roots and the soil. Four isolates each of B. rouxiae and Fov were collected from cotton fields in Australia and were characterised for virulence on cotton under controlled plant growth conditions. While the identity of all four B. rouxiae isolates were confirmed by multi-loci sequencing, only two of them were found to be pathogenic on cotton, suggesting variability in the ability of isolates of this species to cause disease. The four Fov isolates were phylogenetically clustered together with the other Australian Fov isolates and displayed both external and internal symptoms characteristic of Fusarium wilt on cotton plants. Furthermore, the isolates appeared to induce varied levels of plant disease severity indicating differences in their virulence on cotton. To contrast the virulence of the Fov isolates, four putatively non-pathogenic Fusarium oxysporum (Fo) isolates collected from cotton seedlings exhibiting atypical wilt symptoms were assessed for their ability to colonise cotton host. Despite the absence of Secreted In Xylem genes (SIX6, SIX11, SIX13 and SIX14) characteristic of Fov, all four Fo isolates retained the ability to colonise cotton and induce wilt symptoms. This suggests that slightly virulent strains of Fo may contribute to the overall occurrence of Fusarium wilt in cotton fields. Findings from this study will allow better distinction to be made between plant pathogens and endophytes and allow fungal effectors underpinning pathogenicity to be explored.

Image stitching is a crucial aspect of image processing. However, factors like perspective and environment often lead to irregular shapes in stitched images. Cropping or completion methods typically result in substantial loss of information. This paper proposes a method for rectifying irregularly images into rectangles using deformable meshes and residual networks. The method utilizes a convolutional neural network to quantify rigid structures of images. Choosing the most suitable mesh structure based on the extraction results, offering options such as triangular, rectangular, and hexagonal. Subsequently, the irregularly image, predefined mesh structure, and predicted mesh structure are input into a wide residual neural network for regression. The loss function comprises local and global, aimed at minimizing the loss of image information within the mesh and global target. This method not only significantly reduces information loss during rectification but also adapting to different images with various rigid structures. Validation on the DIR-D dataset shows this method outperforms state-of-the-art methods in image rectification.

In this work, we introduce a generalized measure of cumulative residual entropy and study its properties. We show that several existing measures of entropy such as cumulative residual entropy, weighted cumulative residual entropy and cumulative residual Tsallis entropy, are all special cases of the generalized cumulative residual entropy. We also propose a measure of generalized cumulative entropy, which includes cumulative entropy, weighted cumulative entropy and cumulative Tsallis entropy as special cases. We discuss generating function approach using which we derive different entropy measures. Finally, using the newly introduced entropy measures, we establish some relationships between entropy and extropy measures.

Corn fiber is a co-product of commercial ethanol dry-grind plants, which is processed into distillers dried grains with solubles (DDGS) and used as animal feed, yet it holds high potential to be used as feedstock for additional ethanol production. Due to the tight structural make-up of corn fiber, a pretreatment step is necessary to make the cellulose and hemicellulose polymers in the solid fibrous matrix more accessible to the hydrolytic enzymes. A pretreatment process was developed in which whole corn kernels were soaked in aqueous solutions of 2.5, 5.0, 7.5 and 10.0 wt% ammonia at 105oC for 24 h. The pretreated corn then was subjected to a conventional mashing procedure and subsequently ethanol fermentation using a commercial strain of natural Saccharomyces cerevisiae with addition of a commercial cellulase. Pretreatment of the corn with 7.5 wt% ammonia solution plus cellulase addition gave highest ethanol production, which improved the yield in fermentation using 25 wt% solid from 334 g ethanol/kg corn obtained in the control (no pretreatment and no cellulase addition) to 379 g ethanol/kg corn (a 14% increase). The process developed can potentially be implemented in existing dry-grind ethanol facilities as a “bolt-on” process for additional ethanol production from corn fiber, and this additional ethanol can then qualify as “cellulosic ethanol” by the EPA’s Renewable Fuels Standard and thereby receive RINS (Renewable Identification Numbers).

Composites of Ag and TiO2 nanoparticles on cotton fabrics were synthetized in-situ by sono-chemical and hydrothermal methods achieving the successive formation of Ag-NPs and Ti-NPs directly on the fabric. The impregnated fabrics were characterized by ATR-FTIR spectroscopy, high resolution microscopy (HREM), scanning electron microscopy coupled with Ener-gy-dispersive X-ray spectroscopy (SEM-EDS), Raman, photoluminescence, UV-vis and DRS spectroscopies and by tension tests. Results showed the successful formation and impregnation of NPs on the cotton fabric, with a negligible leaching of NPs after several washing cycles. The photocatalytic activity of supported NPs was assessed by the degradation of methyl blue dye (MB) under solar and UV irradiation revealing improved photocatalytic activity of the Ag-TiO2/cotton composites due to a synergy of both Ag and TiO2 nanoparticles. This behavior is attributed to a diminished electron-hole recombination effect in the Ag-TiO2 cotton samples. The biocide activity of these composites on the growth inhibition of Staphylococcus aureus (Gram+) and Escherichia coli (Gram-) was confirmed, revealing interesting possibilities for the utilization of the functionalized cotton fabric as protective cloth for medical applications.

Cotton is a potential and excellent candidate to balance both agricultural production and reme-diation of mercury-contained soil, as its main production fiber hardly involve into food chains. However, there is known rarely about the tolerance and response to Hg environments in cotton. In this study, The biochemical and physiological damages, in response to mercury (Hg), were investigated in upland cotton seedlings. The results on cottonseeds germination, indicated the germination rate were suppressed by high Hg levels, as the decrease of percentage was more than 10% at 1000 µM Hg. Shoots and roots’ growth were significantly inhibited above 10 µM Hg. The inhibitor rates (IR) in fresh weight were close between shoots and roots, whereas that in dry weight the root growth was more obviously influenced by Hg. In comparison of organs, the growth inhibition ranked as root > leaf > stem. The declining of translocation factor (TF) op-posed the Hg level even as low to 0.05 at 50 µM Hg. The assimilation of cotton plants was af-fected negatively by Hg toxicity, as evidenced from the performances on photosynthesis pig-ments (chlorophyll a and b) and gas exchange (Intercellular CO2 concentration (Ci), CO2 assimila-tion rate (Pn) and stomatal conductance (Gs)). Sick phenotypes on leaf surface included small white zone, shrinking and necrosis. Membrane lipid peroxidation and leakage were Hg dose-dependent as indicated by malondialdehyde (MDA) content and relative conductivity (RC) values in leaves and roots. More than 10 µM Hg damaged antioxidant enzyme system in both leaves and roots (P<0.05). Concludingly, 10 µM Hg post negative consequences to upland cotton plants in growth, physiology and biochemistry, whereas high phytotoxicity and damage ap-peared at more than 50 µM Hg concentration.

Residual sugars (RS) in wine are the sugars that remain in a wine after fermentation is complete. In some wine styles, such as semi-dry wines, the accurate measurement of the RS concentration is critical for both qualitative and legislative reasons. Brix, measured by a simple refractometer, can give a good estimation of the RS concentration in the must, but during fermentation, the presence of alcohol leads to inaccurate sugar measurements. In order to measure the RS accurately, other more precise techniques are used, most of which are expensive or require professional skills. Therefore, novel approaches for rapid, easy, and practical measurements for estimating the sugar content were suggested over the years. However, most of these methods do not supply an actual measurement of RS but rather give brix values, and those that measure RS involve special equipment, which is less relevant for small wineries. This study suggests a novel model for predicting and controlling the wine's residual sugar. The data the model uses is the initial brix of the must before fermentation and its density during fermentation. The model was created by measuring actual residual sugars during the fermentation of natural and synthetic musts, with various degrees of initial brix levels, while simultaneously measuring their densities and correlating the two measurements. Linear regression between the residual sugar of the wine and its density was obtained for all treatments and repetitions (i.e., different values of must initial brix) with R² values above 0.97. Using the model, one can calculate (before commencing the fermentation) the density values at which the fermentation will reach a particular desired residual sugar value for a specific initial brix level; the model is applicable for the fermentation conditions used in this work, i.e., brix levels of 18-27˚Bx, Saccharomyces cerevisiae strains (fx-33 and fx-10) in common conditions of fermentation regarding temperature and aeration.

Single Image Super Resolution (SSIR) is a problem in computer vision where the goal is 1 to create high-resolution images from low-resolution ones. It has important applications in fields 2 such as medical imaging and security surveillance. While traditional methods such as interpolation 3 and reconstruction-based models have been used in the past, deep learning techniques have recently 4 gained attention due to their superior performance and computational efficiency. This article proposes 5 an Autoencoder based Deep Learning Model for SSIR, in particular, a light model that uses fewer 6 parameters without compromising performance. The down-sampling part of the Autoencoder 7 mainly uses 3 by 3 convolution and has no subsampling layers. The up-sampling part uses transpose 8 convolution and residual connections from the down sampling part. The model is trained using a 9 subset of the VILRC ImageNet database. The model is evaluated using quantitative metrics PSNR, 10 SSIM as well as qualitative measures such as perceptual quality. PSNR and SSIM figures as high as 11 76.06 and 0.93 are reported.

Remote sensing imagery is of great significance for policy decisions, especially for disaster assessment and disaster relief. To ensure the privacy and inviolability of personal buildings, the information containing these buildings must be anonymized during the remote sensing mapping process. Traditional processing methods for these targets in remote sensing mapping are mainly based on manual retrieval and image editing tools, which are inefficient. Deep learning provides a new direction for target hiding. Although the image inpainting method based on deep learning is faster than the manual method, the cost of training calculation is a disadvantage. And the element-wise product operation used in the model increases the risk of vanished or exploded gradients. We propose a Residual Attention Target Hiding (RATH) model for remote sensing target hiding based on deep learning. RATH uses residual attention modules to replace gated convolutions, reducing parameters and mitigating gradient issues. The residual attention module preserves gated convolution performance but provides an adjustable kernel size. RATH retains gated convolutions for dynamic feature selection and balances model depth and width. Furthermore, this paper modifies the contextual attention layer by adjusting the fusion process to enlarge the fusion patch size. Finally, we extend the edge-guided function to preserve the original target information and confound viewers. Ablation studies on an open dataset prove RATH’s efficiency for image inpainting and target hiding. RATH achieves state-of-the-art results with lower complexity. And it has the highest similarity for edge-guided target hiding. RATH enables robust, efficient target hiding for privacy protection in remote sensing imagery while balancing performance and complexity. Experiments show RATH's superiority over existing methods in hiding arbitrary-shaped targets.

Hydrogel wound dressings hold great potential in eliminating bacteria and accelerating the healing process. However, it remains a challenge to fabricate hydrogel wound dressings that simultaneously exhibit excellent mechanical and photothermal antibacterial properties. Here we report the development of polydopamine-functionalized graphene oxide/calcium alginate/Polypyrrole cotton fabric-reinforced hydrogels (abbreviated as rGO@PDA/CA/PPy FHs) for tackling bacterial infections. The mechanical properties of hydrogels were greatly enhanced by cotton fabric reinforcement and an interpenetrating structure, while excellent broad-spectrum photothermal antibacterial properties based on the photothermal effect were obtained by incorporating PPy and rGO@PDA. Results indicated that rGO@PDA/CA/PPy FHs exhibited superior tensile strength in both the warp (289±62.1N) and weft directions (142±23.0N) similar to cotton fabric. By incorporating PPy and rGO@PDA, the swelling ratio was significantly decreased from 673.5% to 236.6%, while photothermal conversion performance was significantly enhanced with a temperature elevated to 45.0 ℃. Due to the synergistic photothermal properties of rGO@PDA and PPy, rGO@PDA/CA/PPy FHs exhibited excellent bacteria-eliminating efficiency for S. aureus (0.57%) and E. coli (3.58%) after exposure to NIR for 20 min. We believe that the design of fabric-reinforced hydrogels could serve as a guideline for developing hydrogel wound dressings with improved mechanical properties and broad-spectrum photothermal antibacterial properties for infected wound treatment.

Insecticidal toxins from Bacillus thuringiensis (Bt) are valuable tools for pest management worldwide, contributing to the management of human disease insect vectors and phytophagous insect pests of agriculture and forestry. Here, we report the effects of dual and triple Bt toxins expressed in transgenic cotton cultivars on the fitness and demographic performance of Helicoverpa zea (Boddie), a noctuid pest known as cotton bollworm and corn earworm. Life-history traits were determined for individuals of three field populations from a region where H. zea overwintering is likely. Triple-gene Bt cotton cultivars expressing Cry and Vip3Aa toxins killed 100% of the larvae in all populations tested. In contrast, dual-gene Bt cotton expressing Cry1Ac+Cry1F and Cry1Ac+Cry2Ab2 allowed population growth with the intrinsic rate of population growth (rm) 38% lower than on non-Bt cotton. The insects feeding on Bt cotton plants expressing Cry1Ac+Cry2Ab2, Cry1Ac+Cry1F, or Cry1Ab+Cry2Ae exhibited reduced larval weight, survival rate, and increased development time. Additionally, fitness parameters varied significantly among the insect populations, even on non-Bt cotton plants, likely because of their different genetic background and/or previous Bt toxin exposure. This is the first report of the comparative fitness of H. zea field populations on dual-gene Bt cotton after the recent reports of field resistance to certain Bt toxins. These results document the population growth rates of H. zea from an agricultural landscape with 100% Bt cotton cultivars. Our results will help to refine models designed to predict resistance evolution and improve insect resistance management for Bt crops.

Polyploidy, a prevalent event in plant evolution, drives phenotypic diversification and speciation. While transcriptional changes and regulation in polyploids have been extensively studied, the translational level impact remains largely unexplored. To address this gap, we conducted a com-parative transcriptomic and translatomic analysis of cotton leaves from allopolyploid species G. hirsutum (AD1) and G. barbadense (AD2) relative to their model A-genome and D-genome diploid progenitors. Our data revealed that while allopolyploidization significantly affects the transcrip-tional landscape, its impact on translation was relatively modest, evidenced by a narrower ex-pression range and fewer expression changes in ribosome-protected fragments than in mRNA levels. Allopolyploid-specific changes commonly identified in both AD1 and AD2 were observed in 7,393 genes at either transcriptional or translational levels. Interestingly, the majority of translational changes exhibited concordant down-regulation in both ribosome-protected fragments and mRNA, particularly associated with terpenoid synthesis and metabolism. Regarding translational efficiency (TE), at least one-fifth of cotton genes exhibit translational level regulation, with a general trend of more down-regulation than up-regulation of TE. The magnitude of translational regulation was slightly reduced in allopolyploids compared to diploids, and allopolyploidy tends to have a more profound impact on genes and functional associations with ultra-low TE. Moreover, we demonstrated a reduced extent of homeolog expression biases during translation compared to transcription. In conclusion, our study provides insights into the regulatory consequences of allopolyploidy post-transcription, contributing to a comprehensive understanding of regulatory mechanisms of duplicated gene expression evolution.

Cotton is the most important natural fiber cash crop, which has high commodity economic benefits and provides an important material foundation for China's construction. With the improvement of textile technology and living standard, higher requirements are put forward for raw cotton quality. Traditional cotton breeding methods need typing and selection. With the development of biotechnology and the research of genomics, genomic selection has been widely used in cotton breeding. Genomic selection is a new breeding method, which can be selected and bred by constructing a prediction model and using high-density molecular markers covering the whole genome. In this study, the application of various genomic selection models in cotton fiber quality was explored, which provided more reliable information for genetic breeding improvement in the future, thus helping to improve the efficiency of actual cotton breeding.

Bollworm poses a significant threat to cotton crops worldwide, including in the Fergana province of Uzbekistan. This study aims to explore innovative approaches to bollworm control and contribute to the global understanding of integrated pest management strategies (IPM). Using an extensive literature review and field observations, the study evaluates the effectiveness of an integrated protection system in reducing reliance on chemical inputs while increasing overall efficiency. The results highlight the multigenerational life cycle of bollworm, its impact on various crops, and the need for artificial biological control methods and targeted insecticide applications. In addition, the study highlights the need to adopt globally accepted IPM practices to ensure sustainable pest management. The findings underscore the importance of collaboration among researchers, farmers, policymakers, and industry representatives in developing and implementing advanced control measures. Through integrated approaches and the incorporation of scientific advances, bollworm infestations can be contained while safeguarding agricultural productivity and minimizing environmental risks.

Aiming at the problems that the parameters of YOLOv5s model are too large and the computing resources of development board memory are limited, a new target detection method based on deep learning YOLOv5 algorithm model is proposed. First, the light-weight module Gz-ShffleNetv2 is used to construct cotton top bud feature extraction unit, which reduces the number of parameters and improves the running speed. It can be better applied in image classification, speed up detection and meet the requirements of mobile end of development board. Secondly, in order to solve the problem of decreasing detection accuracy caused by lightweight, BotNet and C3SE attention mechanism are added to focus on specific areas of cotton terminal bud. Combined with YYG loss function XIOU boundary frame regression loss, more feature information and rich feature MAP were obtained to further improve the accuracy of target detection. Through analysis of research and experimental results, the average accuracy map reached 91.3% under the Windos system NVIDIA Geforce RTX 2060 SUPER detection. While maintaining high precision identification, the number of parameters of YOLOv6 and YOLOv7-tiny network model is reduced by 83% and 53%, respectively, and the detection accuracy is increased by 1.2% and 7.7%, respectively. Compared with YOLOv5 reasoning image, the speed of image is increased by 0.035s, and the detection accuracy of MAP_0.5:0.95 is increased by 1%. At the same time, PyQt5 and YOLOv5 target detection algorithms are used to design a cotton top bud identification system, which makes cotton top bud detection more intuitive and convenient for subsequent hardware development and use.

The limited availability of water resources worldwide presents obstacles, to the progress of ag-riculture. This situation calls for the implementation of water saving technologies to address these challenges effectively. The quest for technologies that conserve water in agriculture, par-ticularly within the context of cotton production, is related to the study of the impact of drought on the growth, leaf surface area, accumulation of dry matter, boll number, and productivity. The benefits of local drip irrigation have been established. Various models and strategies for opti-mizing and improving the efficiency of how we use water for irrigation purposes. In a market driven economy the effective utilization of water assetsis closely linked to the improvement of managing mineral nutrients. To enhance both the quantity and quality of production, nitrogen is the key factor element that plays a role in the process. The formation of highly efficient cotton crops by adapting the growing technology to the specific soil-climatic conditions of the area, in-cluding controlling nitrogen fertilizing and irrigation, is the primary method to achieve con-sistent harvests. The results of irrigation with water deficit and feeding plants with different fer-tilizer rates are presented. This matter is presently significant, in achieving dependable crop harvests supporting the economic growth of farms and safeguarding the well being of agricul-tural environments.

Plastic contamination is a burning issue costing the global cotton and textile industries billions of dollars annually. Any time plastics from different sources end up in a cotton lint bale, the value to the textile mills plummets significantly. Various industry players have therefore made a concerted effort to find lasting solutions to the menace posed by plastic to cotton profitability and sustainability. Nevertheless, until now, there have been no up-to-date comprehensive documents detailing the numerous and ever-growing efforts committed to solving this challenge. Therefore, this article provides a detailed yet compact review of this highly dynamic subject matter. First, it puts into perspective plastic contamination in the cotton and textile industries. Then, the cotton value chain is subdivided into phases from pre-cultivation to textile mills. The root causes of plastic contamination are discussed in each stage, followed by discussions of some already developed and emerging solutions in response to the challenge by the affected industries and researchers. Concluding from the author’s perspective, the paper makes projections for the future directions of plastic mitigation efforts within the cotton and textile industries. This article also infers from the reviewed literature that research on finding alternative materials to plastic as module wrap, the development of new, effective, and all-condition plastic sensing techniques for ginning and spinning equipment, and standardized protocols for UAV in-field surveys of plastic trash are some of the areas that will be beneficial to finding a permanent solution to the challenge.

This study investigates the application of deep residual networks for predicting the dynamics of interacting three-dimensional rigid bodies. We present a framework combining a 3D physics simulator implemented in C++ with a deep learning model constructed using PyTorch. The simulator generates training data encompassing linear and angular motion, elastic collisions, fluid friction, gravitational effects, and damping. Our deep residual network, consisting of an input layer, multiple residual blocks, and an output layer, is designed to handle the complexities of 3D dynamics. We evaluate the network's performance using a dataset of 10,000 simulated scenarios, each involving 3-5 interacting rigid bodies. The model achieves a mean squared error of 0.015 for position predictions and 0.022 for orientation predictions, representing a 25% improvement over baseline methods. Our results demonstrate the network's ability to capture intricate physical interactions, with particular success in predicting elastic collisions and rotational dynamics. This work significantly contributes to physics-informed machine learning by showcasing the immense potential of deep residual networks in modeling complex 3D physical systems. We discuss our approach's limitations and propose future directions for improving generalization to more diverse object shapes and materials.

In this paper, we introduce ResNetMF, a groundbreaking approach that harnesses the power of residual network matrix factorization to revolutionize recommendation systems. ResNetMF integrates residual networks, renowned for their ability to capture intricate patterns and features, with matrix factorization techniques that excel in modelling user-item interactions. This fusion presents a novel solution that surpasses the limitations of traditional recommendation systems. Through comprehensive experimentation and evaluation of diverse datasets, ResNetMF demonstrates remarkable enhancements in recommendation accuracy and efficiency. By effectively capturing both linear and nonlinear relationships in user-item interactions, ResNetMF provides superior recommendation quality. The outcomes from experiments unequivocally highlight the superiority of ResNetMF over existing state-of-the-art recommendation approaches, thereby validating its innovative nature and underscoring its potential to shape the future of recommendation systems. Through the integration of the deep residual network, ResNetMF approach facilitates the training of neural networks, enabling them to explore the underlying data layers more comprehensively. Extensive experimentation and evaluation across various datasets provide compelling evidence for the superiority of ResNetMF. Moreover, the proposed method utilized natural language processing (NLP) techniques for targeted information dissemination in recommendation systems, emphasizing the importance of personalized and relevant recommendations for user satisfaction and engagement.

Poly-DADMAC (PD) is a commonly used organic polymer in water treatment, known for its effectiveness as a coagulant. However, its presence as a residue in water raises concerns related to membrane fouling and the potential formation of carcinogenic compounds. Therefore, fast and simple quantification is necessary to efficiently control and monitor the optimal dose of poly-DADMAC with minimal negative effects. This study introduces a new colorimetric quantification method for poly-DADMAC, based on complexation with a cationic dye (fast green- FG). The method was examined through varying conditions which included different analytical and commercial poly-DADMAC formulations and concentrations. The experiments confirm its effectiveness in quantifying poly-DADMAC with a detection limit of 3.22 µg L^-1 (0.02 µM based on monomers' molecular weight), which is one order of magnitude lower than regulatory requirements (50 µg L^-1). To validate the method, the effect of pH was examined, and implementation demonstrations were conducted on cyanobacteria and cowshed polluted water samples. This research introduces a fast, cost-effective innovative method to accurately quantify poly-DADMAC, enhancing water treatment strategies for high-quality purification and water reuse

The study of cell-free DNA (cfDNA) and other peripheral blood components (known as “liquid biopsies”) is promising and has been investigated especially in solid tumors. Nevertheless, it is increasingly showing greater utility in the diagnosis, prognosis, and response to treatment of hematological malignancies; in the future, it could prevent invasive techniques, such as bone marrow (BM) biopsy. Most of the studies about this topic have been focused on B cell lymphoid malignancies; some of them have shown that cfDNA can be used as a novel way for diagnosis and minimal residual monitoring in B cell lymphomas, using techniques such as next-generation sequencing (NGS). In myelodysplastic syndromes, multiple myeloma, or chronic lymphocytic leukemia, liquid biopsies may allow for an interesting genomic representation of the tumor clones affecting different lesions (spatial heterogeneity). In acute leukemias, it can be helpful in the monitoring of early treatment response and the prediction of treatment failure. In chronic lymphocytic leukemia, the evaluation of cfDNA permits the definition of clonal evolution and drug resistance in real-time. However, there are limitations such as the difficulty in obtaining sufficient circulating tumor DNA for achieving a high sensitivity to assess minimal residual disease or the lack of standardization of the method and clinical studies to confirm its prognostic impact. This review focuses on clinical applications of cfDNA on minimal residual disease in hematological malignancies.

Welded structures are subjected to internal residual stress after manufacturing that may affect the structural strength and normally are associated with an increase on initial geometrical imperfections. This study presents a simplified method to generate an adequate representation of residual stresses on Finite Element models for structural analysis of thin-walled structures and other applications. The results obtained shown that the methodology proposed to introduce residual stresses is simple, accurate and efficient on the modulation of post-welding stresses and their pattern, thus it may be used for simulation of the thermal process.

The production of plants and crops is influenced by environmental stress, which is a serious scientific issue. Cotton is an essential crop for producing natural fibers that are used to make biofuel and edible oils. Salinity is the main element that influences cotton growth during the beginning of germination. The type of salt and the growth stage affects how sensitive a plant is to salt stress. Developing ways to enhance cotton performance in salty circumstances can be aided by an understanding of the response of cotton to salt, its mechanism of resistance, and its management methods. Osmotic and ionic imbalances originate due to the deposition of soluble salts under salinity stress in the plant's root zone. Soil salinity significantly reduces plant growth due to several factors, such as nutritional ion imbalance, which reduces K+, PO4-, and NO- absorption, excessive salt chloride concentrations, and osmotic stress, which hinders water availability. Research has revealed that compared to subsequent stages, the germination, emergence, and seedling phases are more vulnerable to salinity stress, which ultimately affects the seed cotton yield by delaying blooming, reducing fruiting positions, shedding fewer fruits, and reducing boll weight. The morphology, growth of cotton roots, shoots, yield, and fiber quality are all strongly impacted by salinity stress. It slows down plant feeding, cellular metabolism, and photosynthesis. The soil, water, and climate all affect how the plant responds to salinity stress. During salt stress, excessive exclusion of sodium or its compartmentalization is the key adaptation process in cotton. A major adaptive potential to create cotton types that can withstand salt is provided by the up-regulation of both physicochemical and non-enzymatic antioxidant genes. A successful strategy to increase cotton germination in saline soils is seed priming. Moreover, the transgenic strategy might be a viable choice for improving cotton yield in saline environments. Our review focuses on the impacts of salinity on cotton productivity as well as how plants react to salt stress. It also clarifies recent genetic advancements and molecular breeding for cotton's resistance to soil salt. To create salt-tolerant cultivars, a combination of traditional breeding and novel molecular approaches will be useful.

Morphological parameters like cotton height, branches, Leaf Area Index and biomass are mainly affected by the vegetation water content (VWC). Periodical assessment of the VWC and crop parameters is required for timely management of the crop for maximizing yield. The study aimed at using both optical and microwave remotely sensed data to assess cotton crop condition based on the above mentioned traits. Vegetation indices (VI) derived from ground based measurements (5 narrow band and 2 broad band VIs) as well as satellite derived reflectance (2 broad band VIs) were assessed. Regression models were derived for estimating LAI, biomass and plant water content using the ground based indices and applied to the satellite derived spectral index (from LISS-III) map to estimate the respective parameters. HH and HV polarization from RISAT-1 were used to derive Radar Vegetation Index (RVI). The coefficient of determination of the model for estimating LAI, biomass and vegetation water content of cotton with optical vegetation index as input parameter were found to be 0.42, 0.51 and 0.52, respectively. The correlation between RVI and plant height, date of planting in terms of the age of the crop and vegetation water content were found to range between 0.4 to 0.6. The fresh biomass from RVI showed spatial variability from 100 gm-2 to 4000 gm-2 while the dry biomass map derived from NDVI showed spatial variability of 50 to 950 g m-2 for the study area. Plant water content in the district varied from 65 to 85%. The correlation between optical vegetation index and RVI was not significant. Hence a multiple linear regression model using both optical index (NDVI and LSWI) and SAR index (RVI) was developed to assess the LAI, biomass and plant water content. The model showed a R2 of 0.5 for LAI estimation but not significant for biomass and water content. This study show cased the use of combined optical and microwave (C band) remote sensing for cotton condition assessment.

A field study was conducted at the Eastern Mediterranean Agricultural Research Institute, Adana, Turkey, during the 2022/23 cropping seasons to examine the impact of Mepiquat chloride dosage applied at different intervals to optimize growth, yield characteristics enhancement and improve fiber quality attributes of cotton. The study employed a split-split plot design with three replications. The results revealed that differences among treatments were not statistically significant for most parameters investigated. The observed discrepancies indicated that all treatments tested in 2012 delayed cotton development, whereas in 2023, they led to premium fibers. In 2023, the fiber percentage was highest in the control treatment, and in 2022, it was highest at 400 mL·ha-1. Across all years, the Selin variety exhibited the highest fiber percentage when Mepiquat chloride was applied at the bolling stage. The shoot-root ratio was highest at 400 mL·ha-1 during harvest in 2022 and at 0 mL·ha-1 during the reproductive stage in 2023. Overall, the results demonstrated that the application of Mepiquat chloride altered the physiological characteristics of the cotton plants, leading to bottom-up effects on cotton performance. This implies that the effectiveness of Mepiquat chloride in cotton production to alleviate drought stress is influenced by weather-related conditions.

The growing use of drones in precision agriculture highlights the need for enhanced operational efficiency. Despite the ability of computer vision based on deep learning has made remarkable progress in the past ten years, when it comes to segmentation task on UAVs, there is always a conflict between the demand of high precision and low inference latency. Due to such a dilemma, we propose the IRB-YOLO, an efficiency model based on Inverted Residual Block, devoting to provide constructive strategies in real-time detection tasks of UAV camera. The working details of this paper are as follows: (1) This paper innovates with a IR-Block(Inverted Residual Block), integrated into a refined YOLOv8-seg structure to create IRB-YOLO. This model specializes in pixel-level classification of UAV-acquired RGB images, facilitating the creation of exact maps to guide agricultural strategies. (2)When it comes to the experiments on a Vatica dataset with any other light-weight segmentation model, IRB-YOLO achieve at least a 3.3% increase in mAP. Further validation using a diverse species dataset confirms its robust generalization. (3)Without overloading the complex attention mechanism and deeper and deeper network, a stem that incorporates efficient feature extraction components, inverted residual block, can still possess outstanding modeling capabilities. IRB-YOLO builds a bridge between academic research and edge deployment of drones, making it applicable in real-world scenarios.

Verticillium wilt (VW) is a soil borne fungal diseases caused by Verticillium dahliae Kleb, and lead to serious damage to cotton production annually in the world. In our previous study, a transmembrane protein 214 protein (TMEM214) gene associated with VW resistance was map-based cloned from Gossypium barbadense (G. barbadense). TMEM214 proteins are a kind of transmembrane protein, but their function in plants is rarely studied. To reveal the function of TMEM214s in VW resistance, all six TMEM214s were cloned from G. barbadense in this study. These genes were named as GbTMEM214-1, GbTMEM214-4 and GbTMEM214-7 according to their location on the chromosomes, and the encoded proteins are all located on cell membrane. TMEM214 genes were all induced by Verticillium dahliae inoculation and showed significant differences between resistant and susceptible varieties, but the expression patterns of GbTMEM214s under different hormone treatments were significantly different. Virus-induced gene silencing analysis showed the resistance to VW of GbTMEM214s-silenced lines decreased significantly, which further proves the important role of GbTMEM214s in the resistance to Verticillium dahliae. Our study provides an insight into the involvement of GbTMEM214s in VW resistance, which was helpful to better understand the disease resistance mechanism of plants.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

Solution-based inorganic-organic halide perovskites are of great interest to researchers because of their unique optoelectronic properties and easy processing. However, polycrystalline perovskite films often show inhomogeneity due to residual strain induced during the film’s post-processing phase. In turn, these strains can impact both their stability and performances. An exhaustive study of residual strains can provide a better understanding and control of how they affect the performance and stability of perovskite films. In this work, we explore this complex interrelationship between residual strains and electrical properties for methylammonium \chemform{CH_3NH_3PbI_{3-x}Cl_x} films using grazing incident X-ray diffraction (GIXRD). We correlate with their resistiviy and carrier mobility using Hall effect. The sin^2($\psi$) technique is used to optimize the annealing parameters for the perovskite films. We also establish that temperature-induced relaxation can yield significant enhancement of the charge carrier transports in perovskite films. Finally, we also use Raman micro-spectroscopy to assess the degradation of perovskite films as a function of their residual strains.

The paper presents the results of experimental studies and mathematical modeling of the effect of stress accumulation in thermosetting epoxy polymer "hot" curing on anhydride hardener. Stress accumulation occurs under cyclic thermomechanical action in a locked rod, similar effects are observed, for example, in thermoplastic elements subjected to the combined effect of mechanical loads and variable temperatures. Experimental results have shown that under cyclic thermomechanical loading during exploitation it is possible to accumulate residual stresses in the thermosetting polymer. A multi-element structural mathematical model with memory for thermomechanical load, which allows to consider the accumulation of residual thermal stresses, has been proposed. The results of modeling and experiment are compared. Based on the results, corrections are made in the approach to the application of this model to thermosetting polymers such as the epoxy resin under study. Considering the corrections, a good agreement (the difference is from 1 to 6%) with the results of experimental determination of stresses under complex cyclic thermomechanical load was obtained.

In this study, we introduce a novel framework for the estimation of residual renal function (RRF), based on the population compartmental kinetic behavior of Beta 2 Microglobulin (B2M) and its dialytic removal. Using this model, we simulated a large cohort of patients with various levels of RRF receiving either conventional high-flux hemodialysis or on-line hemodiafiltration. These simulations were used to estimate a novel population kinetic (PK) equation for RRF (PK-RRF) that was validated in an external public dataset of real patients. We assessed the performance of the resulting equation(s) against their ability to estimate urea clearance using cross-validation. Our equations derived entirely from computer simulations and advanced statistical modeling, and had extremely high discrimination (AUC 0.808 – 0.909) when applied to a human dataset of measurements of RRF. A clearance-based equation that utilized pre and post dialysis B2M measurements, patient weight, treatment duration and ultrafiltration had higher discrimination than an equation previously derived in humans. Furthermore, the derived equations appeared to have higher clinical usefulness as assessed by Decision Curve Analysis, potentially supporting decisions that for individualizing dialysis frequency in patients with preserved RRF.

Recently, many authors have been interested to introduce fuzzy implications over t-norms and t-conorms. In this paper, we introduce (S,N) and residuum fuzzy implication for Dubois t-norm and Hamacher's t-norm. Also, new concepts so-called (T,N) and residual fuzzy co-implication in dual Heyting Algebra are investigated. Some examples as well as application are discussed as well.

In this paper, we concentrate on the study of the properties of residual Tsallis entropy for order statistics. Order statistics have an important role in reliability structural engineering for example for modelling lifetimes of series and parallel systems. The residual Tsallis entropy of ith order statistic from a continuous distribution function and its deviation from the residual Tsallis entropy of ith order statistics from a uniform distribution is investigated. In a mathematical framework, a method to express the residual Tsallis entropy of the ith order statistic from a continuous distribution in terms of the residual Tsallis entropy of the ith order statistic from a uniform distribution is provided. This approach may provide insight into the behavior and properties of the residual Tsallis entropy for order statistics. Further, we study the monotonicity properties of the residual Tsallis entropy of order statistics under dierent conditions. By studying these properties, deeper understanding of the relationship between the position of order statistics and the resulting residual Tsallis entropy is gained.

Molecular diagnostics in healthcare relies increasingly on genomic and transcriptomic method-ologies and requires appropriate tissue specimens from which nucleic acids (NA) of sufficiently high quality can be obtained. Besides suration of ischemia and fixation type, NA quality depends on a variety of other pre-analytical parameters, like storage conditions and duration. It has been discussed that improper dehydration of tissue during processing influences quality of NAs and shelf-life of fixed tissue. Here we report on establishing a method to determine the amount of residual water in fixed, paraffin-embedded tissue (fixed by neutral buffered formalin, or a non-crosslinking fixative) and its correlation to the performance of NAs in qRT-PCR analyses. The amount of residual water depended primarily on the fixative type and the dehydration pro-tocol and, to a lesser extent on storage conditions and time. Moreover, we found that these pa-rameters were associated with the qRT-PCR performance of extracted NAs. Besides cross-linking of NAs and modification of nucleobases by formalin, hydrolysis of NAs by residual water was found to contribute to reduced qRT-PCR performance. The negative effects of residual water on NA stability are not only important for the design and interpretation of research, but must also be taken into account in clinical diagnostics where reanalysis of archived tissue from a primary tumour may be required, e.g., after disease recurrence. We conclude that improving shelf-life of fixed tissue requires meticulous dehydration and dry storage to minimize the degradative in-fluence of residual water on NAs.

Rapid and accurate prediction of residual stress in metal additive manufacturing processes is of great importance to guarantee the quality of the fabricated part to be used in a mission-critical application in the aerospace and automotive industries. Experimentation and numerical modeling are valuable tools for measuring and predicting the residual stress; however, to-date conducting experimentation and numerical modeling is expensive and time-consuming. Thus, herein, a physics-based thermomechanical analytical model is proposed to predict the residual stress of the additively manufactured part rapidly and accurately. A moving point heat source approach is used to predict the temperature field by considering the effects of scan strategies, heat loss, and energy needed for solid-state phase transformation. Due to the high temperature gradient in this process, part experiences a high amount of thermal stress following solidification which may exceed the yield strength of the material. The thermal stress is obtained using Green’s function of stresses due to the point body load. The Johnson-Cook flow stress model is used to predict the yield surface of the part under repeated heating and cooling. As a result of the cyclic heating and cooling and the fact that the material is yielded, the residual stress build-up is predicted based on incremental plasticity and kinematic hardening behavior of the metal according to the property of volume invariance in plastic deformation in coupling with the equilibrium and compatibility conditions. The computational methodology is realized with the laser powder fusion of maraging steel 350 as a material of example. The validation of the predictive models has been presented in terms of the comparison of predicted and measured scan-direction and build-direction residual stress distributions along depth of build under various process parameter combinations. Moreover, for the first time, the Jonson-Cook parameters of maraging steel 350 are predicted using analytical modeling of machining forces and non-linear optimization techniques.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.

The residual multiparticle entropy (RMPE) of a fluid is defined as the difference, Δs, between the excess entropy per particle (relative to an ideal gas with the same temperature and density), s_ex, and the pair-correlation contribution, s₂. Thus, the RMPE represents the net contribution to s_ex due to spatial correlations involving three, four, or more particles. A heuristic “ordering” criterion identifies the vanishing of the RMPE as an underlying signature of an impending structural or thermodynamic transition of the system from a less ordered to a more spatially organized condition (freezing is a typical example). Regardless of this, the knowledge of the RMPE is important to assess the impact of non-pair multiparticle correlations on the entropy of the fluid. Recently, an accurate and simple proposal for the thermodynamic and structural properties of a hard-sphere fluid in fractional dimension 1 < d < 3 has been proposed [Santos, A.; López de Haro, M. Phys. Rev. E 2016, 93, 062126]. The aim of this work is to use this approach to evaluate the RMPE as a function of both d and the packing fraction ϕ. It is observed that, for any given dimensionality d, the RMPE takes negative values for small densities, reaches a negative minimum Δs_min at a packing fraction ϕ_min, and then rapidly increases, becoming positive beyond a certain packing fraction ϕ₀. Interestingly, while both ϕ_min and ϕ₀ monotonically decrease as dimensionality increases, the value of Δs_min exhibits a nonmonotonic behavior, reaching an absolute minimum at a fractional dimensionality d ≃ 2.38. A plot of the scaled RMPE Δs/|Δs_min| shows a quasiuniversal behavior in the region −0.14 ≲ ϕ − ϕ₀ ≲ 0.02.

Natural dyes offer a bio-based opportunity to support attractive coloration to textile fabrics made from natural fibers like cotton, wool, hemp and many other materials. They can be part of a strategy to realize fully bio-based textile materials and clothing. Following this statement, the actual study investigates the use of wood extracts for dyeing of cotton fabrics. Actually extract powders of Logwood (Haematoxylon campechianum L.), Brazilwood (Caesalpinia spp.), and Quebracho wood (Schinopsis lorentzii) are used. The dyeing process is modified using different mordants based on iron and aluminum salts. These mordants are applied in pre-, meta- or post-mordant procedures. Color and fastness properties of prepared textile samples are determined by spectroscopic measurements, color measurements, washing procedures and Xenotest for measuring the light fastness. Finally, a broad range of different colorations can be realized by different combinations of wood extracts and mordanting procedures. A good wash fastness is reached for some color shades. For reaching good wash fastness, pre- and meta-mordanting procedures are more advantageous compared to post-mordanting. However, the light fastness of realized samples is only moderate to low. In conclusion, it can be stated that dyes from wood extracts are excellent materials to dye natural fibers if they are combined with the right mordanting agent in pre- or meta-mordanting procedures. The actual study is therefore a good proof-of-concept for the realization of fully bio-based colored textile materials.

Three carbon-chain extension genes associated with fatty acid synthesis in cotton, namely GhKAR, GhHAD, and GhENR, play important roles in oil accumulation in cotton seeds. In the present study, these three genes were cloned and characterized. The expression patterns of GhKAR, GhHAD and GhENR in the high seed oil content cultivars 10H1007, 10H1014, and 10H1041 differed somewhat compared with those of 2074B with low seed oil content at different stages of seed development. GhKAR showed all three cultivars showed higher transcript levels than that of 2074B at 10, 40 and 45 DPA. The expression pattern of GhHAD showed a lower transcript level than that of 2074B at both 10 and 30 DPA but higher transcript level than that of 2074B at 40 DPA. GhENR showed a lower transcript level than that of 2074B at both 15 and 30 DPA. The highest transcript levels of GhKAR and GhENR were detected at 15 DPA in 10H1007, 10H1014, and 10H1041 compared with 2074B. From 5 to 45 days post anthesis (DPA) cotton seed, the oil content accumulated continuously in the developing seed. Oil accumulation reached the peak at 40 DPA to 45 DPA and slightly decreased in mature seed. In addition, GhKAR and GhENR showed different expression patterns in fiber and ovule development processes, in which they showed high expression levels at 20 DPA during fiber elongation stage, but their expression level peaked at 15 DPA during ovule development processes. These two genes showed the lowest expression levels at the late seed maturation stage, while GhHAD showed peak at 10 DPA of fiber development. Compared to 2074B, the oil contents of GhKAR and GhENR overexpression lines increased 1.05~1.08 folds. These results indicated that GhHAD, GhENR and GhKAR were involved in both seed oil synthesis and fiber elongation with dual biological functions in cotton.

Variable nitrogen(N) rate fertilization based on remote sensing is challenging for cotton production fields, but active crop canopy sensors (ACS) appear as an alternative to make this practical on farm since they can be used at night as well. The crop spatial variability in inherent in crop production in general, and not on-the-go solutions can be used with this type of active sensing technologies. Thus, the purpose of this study was to investigate the potential of two vegetation indices to identify the N requirement variability for cotton plants and to develop prototype algorithms for topdressing nitrogen variable rate on commercial and experimental areas, using the N-sufficiency methodology based on virtual reference. The concept of virtual reference is to use a histogram to characterize the vegetation index of properly fertilized plants without establishing an N-rich plot as a reference strip. The experiment was conducted in strips with four different N rates (0, 45, 90 and 180 kgN ha^-1) during the 2015, 2016, 2017 and 2018 crop seasons in partnership with large cotton producers in Mato Grosso and also in experimental area of Embrapa Agrosilvopastoral. Two algorithms for variable rate nitrogen fertilization for cotton were developed, namely: 1) N recommendation algorithm for cotton in commercial production system: N rate (kg.N ha^-1) = -234.79 ISN² + 49,879 ISN + 195.15; R² = 0.97; and 2) for cotton grown in experimental area: N dose (kgN ha^-1) = -174.73 ISN² - 107.21 ISN + 306.78; R² = 0.94.

In order to study the hydrothermal behavior of cotton fiber, the carbonization process and structural evolution of discarded cotton fiber (WCF) under hydrothermal conditions were discussed use microcrystalline cellulose (MCC) and glucose as model compounds. The results showed that high temperature was beneficial to the hydrolysis of discarded cotton fiber, and the yield of the sugar was 4.5% which was lower than that of MCC 6.51%. WFC and MCC are carbonized in 240~260 ℃ and 220~240 ℃ respectively, while the carbonation temperature of glucose is lower than 220 ℃. The quality ratio of C/O in WCF and glucose hydrothermal products is 5.79 and 5.85 respectively; three kinds of hydrothermal carbonization products have similar crystal structure and oxygen-containing functional groups, and the WCF carbonization products contain a lot of irregular particles while the main products of glucose carbonization are 0.5 μm carbon microspheres (CMCC). The results show that glucose is an important intermediate product of WCF hydrolysis carbonation, and there are two main paths of cotton fiber hydrothermal carbonization: some cotton fibers are completely hydrolyzed into glucose and the nucleation is formed, and then the carbon microspheres are grown; for the other part, the glucose ring of the polysaccharide oligosaccharide formed by the incomplete hydrolysis of cotton fiber in the hydrothermal environment of high temperature and pressure breaks, then forms the particulate matters.

Somatic embryogenesis-mediated plant regeneration is essential for genetic manipulation of agronomically important traits in upland cotton. Genotype specific recalcitrance to regeneration is a primary challenge in deploying genome editing and incorporating useful transgenes into elite cotton germplasm. In this study, transcriptomes of a semi-recalcitrant cotton (Gossypium hirsutum L.) genotype ‘Coker312’ were analyzed at two critical stages of Somatic Embryogenesis that includes non-embryogenic callus (NEC) and embryogenic callus (EC) cells, and the results compared to a non-recalcitrant genotype ‘Jin668’. We discovered of 305 differentially expressed genes in Coker312, whereas, in Jin668, about 6-fold more genes (2,155) were differentially expressed. A total of 154 differentially expressed genes were common between the two genotypes. Gene enrichment analysis of upregulated genes identified functional categories such as lipid transport, embryo development, regulation of transcription, sugar transport, vitamin biosynthesis, among others. In Coker312 EC cells, five major transcription factors were highly upregulated: LEAFY COTYLEDON 1 (LEC1), WUS-related homeobox 5 (WOX5), ABSCISIC ACID INSENSITIVE3 (ABI3), FUSCA3 (FUS3), and WRKY2. In Jin668, LEC1, BABY BOOM (BBM), FUS3, and AGAMOUS-LIKE15 (AGL15) were highly expressed in EC cells. We also found that gene expression of these embryogenesis genes was typically higher in Jin668 when compared to Coker312. We conclude that significant differences in expression of the above genes between Coker312 and Jin668 may be a critical factor affecting the regenerative ability of these genotypes.

Thermoplastic composites are continuously replacing thermosetting composites in lightweight structures. However, the accomplished work on the fatigue behavior of thermoplastics is quite limited. In the present work, we propose a numerical modeling approach for simulating fatigue delamination growth and predicting the residual tensile strength of quasi-isotropic TC 1225 LM PAEK thermoplastic coupons. The approach is supported and validated by tension and fatigue (non-interrupted and interrupted) tests. Fatigue delamination growth is simulated using a mixed-mode fatigue crack growth model, which is based on the cohesive zone modeling method. All interfaces between the thermoplastic plies were modelled using cohesive elements. Quasi-static tension analyses on pristine and fatigued coupons were performed using a progressive damage model implementing a set of Hashin-type strain-based failure criteria and a damage mechanics-based material property degradation module. Using the fatigue model, delamination growth was predicted as a function of number of cycles at all interfaces. The results agree well with C-scan images taken on fatigued coupons during interruptions of fatigue tests. An unequal and unsymmetric delamination growth was predicted due to the quasi-isotropic lay-up. Moreover, the combined models capture the decrease in the residual tensile strength of the coupons. In the quasi-static tension analysis of the fatigued coupons, the driving failure mechanisms are the fast propagation of the pre-existing delamination and the severe matrix cracking.

Motivated by the importance of entanglement and correlation indicators in the analysis of quantum systems, we study the equilibrium and the residual entropy in a two-species Bose Hubbard dimer when the spatial phase separation of the two species takes place. We consider both the zero and non-zero-temperature regime. We present different kinds of residual entropies (each one associated to a different way of partitioning the system), and we show that they strictly depend on the specific quantum phase characterizing the two species (supermixed, mixed or demixed) even at finite temperature. To provide a deeper physical insight into the zero-temperature scenario, we apply the fully-analytical variational approach based on su(2) coherent states and provide a considerbly good approximation of the entanglement entropy. Finally, we show that the effectiveness of residual entropy as a critical indicator at non-zero temperature is unchanged when considering a restricted combination of energy eigenstates.

Verticillium wilt (VW) is an important and widespread disease of cotton and once established is long lived and difficult to manage. In Australia, the non-defoliating pathotype of Verticillium dahliae is the most common, and extremely virulent. Breeding cotton varieties with increased VW resistance is the most economical and effective method of controlling this disease and is greatly aided by understanding the genetics of resistance. In this study, VW resistance was investigated in 240 F7 recombinant inbred lines (RIL) derived from a cross between MCU-5 that has good resistance and Siokra 1-4 which is susceptible. Using a controlled environment bioassay, we found that resistance based on plant survival or shoot biomass was complex but with major contributions from chromosomes D03 and D09, with genomic prediction analysis estimating a prediction accuracy of 0.73 based on survival scores compared to 0.36 for shoot biomass. Transcriptome analysis of MCU-5 and Siokra 1-4 roots uninfected or infected with V. dahliae revealed that the two cultivars displayed very different root transcriptomes and responded differently to V. dahliae infection. Ninety-nine differentially expressed genes were located in the two mapped resistance regions and so are potential candidates for further identifying the genes responsible for VW resistance.

Cotton (Gossypium L.) is a major source of natural fibre for the world's textile industry and is also an important oil plant. Cotton fibre is the main source of textiles, the seeds are used for oil and the rest of the bagasse is a high-protein animal feed. In addition, more than 50 industries use cotton's so-called short fibre. Breeding studies in cotton are generally based on crosses between the best genotypes in terms of yield and fibre quality. However, the narrow genetic diversity of cultivars has a negative impact on cotton breeding programmes. For this reason, the identification of genetic resources and the disclosure of genetic diversity are important. Herein, high-resolution capillary gel electrophoresis was used to determine the genetic diversity of G. hirsutum and G. barbadense genotypes. Using 19 EST-SSR markers, a total of 47 genotypes were screened. The PIC values of the markers used ranged from 0.268 to 0.889. The mean PIC value was calculated to be 0.603. Concerning the clustering, PCoA and population structure analyses gave similar results, and the genotypes could be divided into 3 main groups. Genetic admixture with G. hirsutum was found in some genotypes of G. barbadense species. We can conclude that i) the EST-SSR markers used in this study are effective in the determination of genetic diversity, ii) The genetic diversity should be increased through the collection of genetic resources iii) genic EST-SSR markers in this study should be considered in breeding programmes by using them in QTL studies.

In order to formulate a reasonable water input model for cotton fields in southern Xinjiang, scientific and rational fertilization, reduce soil carbon leaching, and improve soil carbon sequestration capacity, the undisturbed soil column leaching test was used to simulate the current field management method in the study area. Two methods of drip irrigation and flood irrigation were set up, and three irrigation and three nitrogen fertilizer levels were used to carry out the undisturbed soil column leaching test. The results showed that the amount and mode of water and nitrogen input affected the distribution and leaching loss of organic carbon and inorganic carbon in soil. When the nitrogen application rate increased from 270 kg·hm-2 to 450 kg·hm-2, the leaching loss of soluble organic carbon and soluble inorganic carbon increased significantly. When the water input increased from 6000 m3·hm-2 to 9000 m3·hm-2, the leaching loss of DOC and DIC increased significantly. The carbon leaching loss under drip irrigation was higher than that under flood irrigation. The leaching rates of DOC and DIC were the fastest under the conditions of high water ( 9000 m3·hm-2 ) and high fertilizer ( 450 kg·hm-2 ). It shows that water and nitrogen input and irrigation methods are important factors affecting soil carbon leaching. In the case of excessive water input, long-term high-frequency irrigation is the main factor affecting carbon leaching.

Cotton is one of the most important economic crops in the world, whereas insect attacks is a prime cause of its losses on yield and quality. Despite it is important, little is known about the mechanism of cotton response to insect. In this study, we simulated insect feeding by applying insect oral secretions (OS) to wounds, and combined transcriptome and metabolome analysis to comprehensively investigate how OS from two major pest species (Helicoverpa armigera and Spodoptera litura) affect cotton defense responses. Obvious differences were observed that 12,668 and 13,379 genes differently expressed respectively in cotton after being treated with different OS when compared with wounding along. Upon the addition of OS, JA-signaling pathway were rapidly and strongly induced, however SA-biosynthesis related gens were significantly down-regulated. By constructing the co-expression gene network, we identified a hub gene which encoding a leucine-rich repeat receptor kinase may play important role in recognition and signal transduction at early stage. We also found that OS from different insect species altered abundance of flavonoid related compound with different patterns. Interestingly, Gossypol which is a well-known anti-insect compound was kept a relative low content after OS application relative to wounding which implied the existence of the suppression effects of OS to cotton defense response. This study illustrated the transcriptional and metabolic changes of cotton in responding to OS from two chewing insect species, identified potential key gene during the interaction process and finds the evidence for OS’s inhibition effects on cotton defense response.

The chromatographic conditions were optimized using headspace gas chromatography, and a simple and rapid method was established for the simultaneous determination of five residual solvents in ursodeoxycholic acid raw materials. The corresponding quality standards were revised. The results showed that the concentration of methanol ranged from 0.06mg/ml to 0.3mg/ml, and the concentrations of acetone, tert butanol, ethyl acetate, and triethylamine showed a good linear relationship with the peak area within the range of 0.1mg/ml to 0.5mg/ml (r=0.999); The quantitation limits for methanol, acetone, tert-butanol, ethyl acetate, and triethylamine were 4.2, 0.9, 1.5, 1, and 0.1 μg/ml, respectively, with detection limits of 1.2, 0.25, 0.025, 0.3, and 0.025 μg/ml, respectively. The recovery rates of each solvent ranged from 92.9% to 106.0%, with RSD% (n=9) less than 3.8%; The method exhibited good repeatability, with RSD% (n=6) less than 2.5%. Furthermore, the durability is good. The established method is simple, accurate, specific, and highly sensitive, and can be used for the simultaneous and rapid determination of five residual solvents in ursodeoxycholic acid raw materials.

Residual dizziness after a liberating maneuver is often referred to by patients as a more disabling set of symptoms than the positional vertigo itself. This situation seems to involve more than half of subjects with labyrintholithiasis. The authors examine the hypothesis according to which residual dizziness involves subjects with labyrintholithiasis on the basis of otoconia.

Safety assessment of structures can be obtained employing limit design to overcome uncertainties concerning actual response due to inelastic constitutive behavior and more generally to non-linear structural response and loads’ random variability. The limit analysis is used for evaluating the safety of the structures directly starting from load level without any knowledge of the load history. In the paper, the lower bound calculation is proposed where a new strain-based approach is used that allowed describing the residual stress and displacement in terms of permanent strain. The strategy used the permanent strain as the effective parameters of the procedure so that it was possible to assess the ductility requirements for the complete load program developed till collapse or shakedown. The procedure is compared to experimental results obtained on aluminum beams in shakedown.

Cotton cultivation and sustaining its productivity is challenging in temperate arid regions around the globe. Exploring suitable cotton cultivation areas to improve productivity in such climatic regions is essential. Thus, this study explores the ecologically suitable areas of cotton cultivation using the Maxent model, having 375 distribution points of long-staple cotton and various factors, including 19 climatic factors, 2 terrain factors, and 6 soil factors in Xinjiang. The area under the curve (AUC) of the predicted results was greater than 0.9, indicating that the model's predictions had fairly high accuracy. However, the main environmental factors that affect cotton's growth are the lowest temperature in the coldest month, the hottest month, the precipitation in the driest season, and the monthly average temperature difference. Further, the temperature factors contribute 71%, while the contribution ratio of terrain and soil factors is only 22%. The research shows that the current planting area is consistent with the predicted area in many areas of the study. Still, some areas, such as the Turpan region, northwest of Bayingolin Mongol Autonomous Prefecture, are supposed to be suitable for planting cotton, but it is not planted. The current potential distribution area of long-staple cotton is mainly located in Aksu Prefecture and the northern part of the Kashgar Prefecture region. The climatic prediction shows that the growing area of long-staple cotton may expand to southern Altay, central Aksu, and Bortala Mongol Autonomous Prefecture. This study will be helpful for cotton cultivation suitability areas in Xinjiang and other regions with similar environments.

The use of machine learning techniques to predict yield based on remote sensing is a no-return path and studies conducted on farm aim to help rural producers in decision-making. Thus, commercial fields equipped with technologies in Mato Grosso, Brazil, were monitored by satellite images to predict cotton yield using supervised learning techniques. The objective of this research was to identify how early in the growing season, which vegetation indices and which machine learning algorithms are best to predict cotton yield at the farm level. For that, we went through the following steps: 1) We observed the yield in 398 ha (3 fields) and eight vegetation indices (VI) were calculated on five dates during the growing season. 2) Scenarios were created to facilitate the analysis and interpretation of results: Scenario 1: All Data (8 indices on 5 dates = 40 inputs) and Scenario 2: best variable selected by Stepwise regression (1 input). 3) In the search for the best algorithm, hyperparameter adjustments, calibrations and tests using machine learning were performed to predict yield and performances were evaluated. Scenario 1 had the best metrics in all fields of study, and the Multilayer Perceptron (MLP) and Random Forest (RF) algorithms showed the best performances with adjusted R2 of 47% and RMSE of only 0.24 t ha^-1, however, in this scenario all predictive inputs that were generated throughout the growing season (approx. 180 days) are needed, so we optimized the prediction and tested only the best VI in each field, and found that among the eight VIs, the Simple Ratio (SR), driven by the K-Nearest Neighbor (KNN) algorithm predicts with 0.26 and 0.28 t ha^-1 of RMSE and 5.20% MAPE, anticipating the cotton yield with low error by ±143 days, and with important aspect of requiring less computational demand in the generation of the prediction when compared to MLP and RF, for example, enabling its use as a technique that helps predict cotton yield, resulting in time savings for planning, whether in marketing or in crop management strategies.