The beneficial effects of Lanthanide incorporation into 0.94Na0.5Bi0.5TiO3-0.06BaTiO3 (BNT-BT) matrix on its functional properties were investigated. The conventional solid-state method was used for synthesizing samples. The structural refinement revealed that all samples crystallized in R3c rhombohedral symmetry. Raman spectroscopy study was carried out using green laser excitation and revealed that no clear perceptible variation in frequency is observed. Dielectric measurements unveiled that the introduction of rare earth obstructed the depolarization temperature promoted in BNT-BT with decreasing the diffusive phase transition with increasing the lanthanide size. Only Dysprosium addition showed comparable diffusion constant and dielectric behavior as the unmodified composition. Further, the comparison of the obtained ferroelectric hysteresis and strain-electric field loops revealed that only Dy-phase exhibited interesting properties comparing parent composition. In addition, the incorporation of lanthanides Ln3+ into the BNT-BT matrix led to the development of luminescence characteristics in the visible and near infrared regions, depending on the excitation wavelengths. The simultaneous occurrence of photoluminescence and ferroelectric/piezoelectric properties opens up possibilities for BNT-BT-Ln to exhibit multifunctionality in a wide range of applications.Keywords: Sodium Bismuth Titanate; structural refinement; dielectric properties; ferroelectric properties; piezoelectric properties; Photoluminescence.

This study focuses on the potential medicinal properties of Campsis radicans L. extracts and its aim is to investigate the antioxidant and antiproliferative effects of these extracts on the human colon adenocarcinoma cell line (HT-29). Cytotoxic activity in the HT-29 cell line was evaluated, and the 3-dimensional structures of phenolic compounds were obtained using the GC-MS method. Docking simulations were performed with AutoDock Vina, targeting proteins that are crucial in the apoptotic pathway (Bax, Bcl-2, and Caspase-3). Drug similarities and ADMET estimates of the phenolic compounds were obtained from databases. The highest antioxidant activity of Campsis radicans L. plant was observed in ethanol and water extracts, with notable inhibition capacities. While the total phenolic content was highest in ethanol, water, and ether extracts respectively the total flavonoid content was highest in ethanol, then ether, and water extracts. Certain elements were undetectable in mineral determination, and others exceeded the toxic doses for plants. The water extract exhibited dose-dependent cytotoxic activity in the HT-29 cell line, with an IC50 value of 4.47 mg/mL. Molecular docking results revealed the binding of phenolic molecules to the active sites of apoptotic pathway proteins. The findings suggest that Campsis radicans L. plant possesses cytotoxic properties, significant phenolic and flavonoid content, and a high antioxidant capacity. These properties make it a potential candidate for treatment use, emphasizing its potential therapeutic value in the HT-29 cell line. Further research and exploration on the identified phenolic compounds could contribute to the development of novel therapeutic agents.

Pigmented corn is a gramineae food of great biological, cultural and nutritional importance for many Latin American countries, with more than 250 breeds in the American continent. It confers a large number of health benefits due to its diverse and abundant bioactive compounds. In this narrative review we decided to organize the information on the nutrients, bioactive compounds and phytochemicals present in pigmented corn, as well as their effects on human health. Phenolic compounds and anthocyanins are some of the most studied and representative compounds in these grasses, with a wide range of health properties, mainly the reduction of prooxidant molecules. Carotenoids are a group of molecules belonging to the terpenic compounds, present in a large number of pigmented corn breeds, mainly the yellow ones, whose biological activity incorporates a wide spectrum. Bioactive peptides can be found in abundance in corn, having very diverse biological effects that include analgesic, opioid, antihypertensive, etc. activity. Other compounds with biological activity found in pigmented corn are resistant starches, some fatty acids, phytosterols, policosanols, phospholipids, ferulic acid and phlobaphenes, as well as a great variety of vitamins, elements, and fibers. This review aims to disseminate and integrate the existing knowledge on compounds with biological activity in pigmented corn, in order to promote their research, interest and use by scientists, nutrition professionals, physicians, industries and the general population.

Two types of heterometallic (Fe(III),Na) silsesquioxanes [Ph₅Si₅O₁₀]₂[Ph₁₀Si₁₀O₂₁]Fe₆(O^2‒)₂Na₇(H₃O⁺)(MeOH)₂(MeCN)_4.5.1.25(MeCN), I, and [Ph₅Si₅O₁₀]₂[Ph₄Si₄O₈]₂Fe₆Na₆(O^2‒)₃(MeCN)_8.5(H₂O)_8.44, II, were obtained and characterized. X-Ray studies established distinctive structures of both products, with pair of Fe(III)-O-based triangles surrounded by siloxanolate ligands, giving fascinating cage architectures. Complex II proved to be catalytically active in the formation of amides from alcohols and amines, thus becoming a rare example of metallasilsesquioxanes performing homogeneous catalysis. Benzene, cyclohexane and other alkanes, as well as alcohols, can be oxidized in acetonitrile solution to phenol, the corresponding alkyl hydroperoxides and ketones, respectively, by hydrogen peroxide in air in the presence of catalytic amounts of complex II and trifluoroacetic acid. Thus, the cyclohexane oxidation at 20 °C gave oxygenates in very high for alkanes yield (48% based on alkane). The kinetic behaviour of the system indicates that the mechanism includes the formation of hydroxyl radicals generated from hydrogen peroxide in its interaction with diiron species. The latter are formed via monomerization of starting hexairon complex with further dimerization of the monomers.

Europium is one of the most reactive lanthanides and humans use it in many different applica-tions, but we still know little about its potential toxicity and cellular response to its exposure. Two strains of the eukaryotic microorganism model Tetrahymena thermophila adapted to high concentrations of two Eu(III) compounds (EuCl3 or Eu2O3) were obtained and compared to a control strain and cultures treated with both compounds. In this ciliate, EuCl3 is more toxic than Eu2O3. LC50 values show that this microorganism is more resistant to these Eu(III) compounds than other microorganisms. Oxidative stress originated mainly by Eu2O3 is minimized by overexpression of genes encoding important antioxidant enzymes. The overexpression of metallothionein genes under treatment with Eu(III) compounds supports the possibility that this lanthanide may interact with the -SH groups of the cysteine residues from metallothi-oneins and/or displace essential cations of these proteins during their homeostasis function. Both lipid metabolism (lipid droplets that fuse with europium-containing vacuoles) and au-tophagy are involved in the cellular response to europium stress. Bioaccumulation, together with a possible biomineralization to europium phosphate, seems to be the main mechanism of Eu(III) detoxification in these cells.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

The development of efficient luminescent systems, such as microcavities, solid state lasers, integrated optical amplifiers, optical sensors is the main topic in glass photonics. The building blocks of these systems are glass-ceramics activated by rare earth ions because they exhibit specific morphologic, structural and spectroscopic properties. Among various materials that could be used as nanocrystals to be imbedded in silica matrix, tin dioxide presents some interesting peculiarities, e.g. the presence of tin dioxide nanocrystals allows increase in both solubility and emission of rare earth ions. Here, we focus our attention on Er³⁺ - doped silica – tin dioxide photonic glass-ceramics fabricated by sol-gel route. Although the SiO₂-SnO₂:Er³⁺ could be fabricated in different geometrical systems: thin films, monoliths and planar waveguides we herein limit ourselves to the monoliths. The effective role of tin dioxide as luminescence sensitizer for Er³⁺ ions is confirmed by spectroscopic measurements and detailed fabrication protocols are discussed.

Fungal infections caused by Candida spp. are responsible for high hospital morbidity and mortality rates. Therefore, there is a continuous search for new antifungal medicines, particularly ones with anti-Candida activity. This review analyzed articles published between 2002 and 2023 considering the anti-Candida activity of chemical compounds identified or isolated in plants of the Anacardiaceae family. In addition, the in-silico prediction of the isolated compounds described was performed. The analysis of 35 studies showed that extracts, essential oils, and compounds from the anti-Candida activity were frequently determined in vitro using the minimum inhibitory concentration (MIC). The most commonly tested species were Candida albicans, C. tropicalis, C. parapsilosis, C. glabrata, C. krusei, and C. guilliermondii, respectively. Essential oils were the most used form (37% of the studies). The isolated compounds with antifungal effects include cardanol, estragole, trans-anethole, β-caryophyllene, myrcene, catechin-3-o-rhamnoside, β-sitosterol-3-O-glucoside, 24Z-isomasticadienolic acid, oleanolic acid, and oleanolic aldehyde. The in-silico evaluation of those isolated compounds revealed the compounds' drug-likeness and possible antifungal activity. However, some of them showed high toxicity. In conclusion, compounds from the Anacardiaceae family show promise for developing new therapeutic antifungal drugs, especially in combination with conventional antifungals.

The pharmacological effects of the fruiting body of Ophiocordyceps sinensis (Os) exerted antioxidant, anti-virus, and immunomodulatory, whereas the anti-inflammatory effects and active components of Os mycelial submerged culture (OMSC) are not known. This study aimed to investigate the active compounds in the fermented liquid (FLOS), hot water (WEOS), and 50-95% (EEOS-50, EEOS-95) ethanol extracts of OMSC and their anti-inflammatory effects and potential mechanisms in LPS-stimulated microglial BV2 cells. The results demonstrated that all of the OMSC extracts could inhibit NO production in BV2 cells. EEOS-95 exhibited the strongest inhibitory effects (41 % inhibitory ability at 500 µg/mL), and its ergosterol, GABA, total phenolic, and total flavonoid contents were significantly higher than those of the other extracts (18.60, 18.60, 2.28, and 2.14 mg/g, p < 0.05, respectively). EEOS-95 also has a strong inhibitory ability against IL-6, IL-1β and TNF-α with IC50 of 617, 277 and 507 µg/mL, respectively, which is higher than that of 1 mM melatonin. The anti-inflammatory mechanism of EEOS-95 seems to be associated with up-regulation of PPAR-γ/Nrf-2/HO-1 antioxidant-related expression and down-regulation of NF-κB/COX-2/iNOS pro-inflammatory expression signaling. Therefore, we hypothesized that EEOS-95 can prevent neurodegenerative diseases, but the effect on the application in vivo should be further investigated.

The pharmaceutical industry is one of the largest pollutants and generator of toxic solvent resi-dues for the environment and human beings. In the last decade, there has been a huge evolution in the design and development of new environmentally friendly products and processes, in re-sponse to the global environmental concern and the growing demand for products with quality ingredients and manufacturing processes aimed at achieving sustainability. Consumers are looking for products with the benefits of natural products, with sustainable and environmentally friendly formulations with few synthetic molecules as possible. Thus, based on the origins of the pharmaceutical industry, it is important to return to Nature and enjoy the benefits that natural products bring to us. Deep eutectic solvents appear as an alternative to toxic solvents commonly used to extract bioactive compounds. These solvents are considered green solvents because they are made up of natural compounds such as sugars, amino acids, and carboxylic acids. In addition, they are simple to prepare, with an atomic economy of 100%, with attractive physicochemical properties. This paper is a comprehensive review in which is described the main properties, characteristics, and production methods of deep eutectic solvents as well as its application to extract from natural sources bioactive compounds with pharmaceutical interest.

The present study comprises the second part of our previous work that dealt mainly with the phytochemical and physicochemical characterization of green coffee, clove, cinnamon/clove and nutmeg ethanolic extracts of grape origin. In the present study, we focused on producing a discriminating model concerning green coffee, clove, cinnamon, cinnamon and clove, and nutmeg fine powders based on multivariate analysis of variance and supervised learning on data of volatile compounds analysis, carried out with solid phase dynamic extraction in combination with gas chromatography/mass spectrometry. Results showed that 7 volatile compounds namely ethylene, methanol, 3-methylpentane, ethyl acetate, 9-hexadecen-1-ol, toluene, and methyl acetate could differentiate the investigated samples resulting in a 100% classification rate using the cross-validation method of linear discriminant analysis. Results were further confirmed using partial least squares regression analysis. The study contributes to the typification of green coffee, cinnamon, clove, cinnamon and clove and nutmeg, based on selected volatile compounds, and provides further support to the literature by means of possible adulteration given the statistical models developed.

In our study we investigated the additive manufacturing (AM) of ceramic-based Functionally Graded Materials (FGM) by the direct AM technology Thermoplastic 3D-Printing (T3DP). Zirconia components with a varying microstructure were additively manufactured by using thermoplastic suspensions with different contents of pore forming agents (PFA) and were co-sintered defect-free. Different materials were investigated concerning their suitability as PFA for the T3DP process. Different zirconia-based suspensions were prepared and used for AM of single- and multi-material test components. All samples were sintered defect-free and in the end we could realize a brick wall-like component consisting of dense (<1% porosity) and porous (approx. 5% porosity) zirconia areas to combine different properties in one component. The T3DP opens the door to AM of further ceramic-based 4D-components like multi-color or multi-material, especially multi-functional components.

Lead optimization in drug discovery is a crucial phase where initial hits are refined into compounds with improved pharmacological properties. While traditional methods rely on manual experimentation and modifications, AI-driven techniques have revolutionized this process by leveraging big data and predictive modeling. This review explores how AI-driven approaches accelerate lead optimization, showcasing examples like deep neural networks and reinforcement learning. Integration of multi-omic data and experimental validation further enhances AI-driven strategies. The future lies in refining these AI methods, democratizing tools, and interdisciplinary collaboration to streamline drug discovery and address medical needs efficiently.

There is a growing trend among consumers to seek out natural foods and products with natural ingredients. This shift in consumer preferences had a direct impact on both food and pharmaceutical industries, leading to a focus of scientific research and commercial efforts to meet these new demands. The aim of this work is to review recent available scientific data on foods of interest, such as artichoke, gooseberry, and polygonoideae plants, as well as olive oil and red raspberries. Interestingly, the urgency of solutions to the climate change emergency has brought new attention to by-products of grapevine bunch stem and cane, which have been found to contain bioactive compounds with potential health benefits. There is a pressing need for a faster process of translating scientific knowledge from the laboratory to real-world applications, especially in the face of the increasing societal burden associated to non-communicable diseases (NCDs), environmental crises, the post-pandemic world, and ongoing violent conflicts around the world.

Background and Objectives: In this current state, Type 2 Diabetes Mellitus (T2DM) is more prevalent in the population, and metformin is used as a first-line medication for treating it. There was up surge in the utilization of alternative therapies in the management of diabetes. Especially in diabetes, Herbal medicines are considered safe and reliable by majority of the population. Aim: The purpose of this research is aimed to estimate the safety and efficacy of Polyherbal Metabolite Compounds (PHMC) capsules in adults with T2DM. Materials and Methods: In this study, 60 T2DM patients aged 18-60 years were randomly assigned to Groups A (30) receiving Metformin 500 mg twice a day after food and Group B (30) receiving PHMC capsule 500 mg twice a day after food in a prospective, randomized and open-label clinical study. The in-silico simulation study was performed to selected plants major compounds on target protein Insulin-like Growth Factor-1 (1K3A). Result: The PHMC is found to be safe and effective in the management of T2DM. The FBS, PPBS and HbA1c were significantly lowered (p

From grape cultivation to ripening and harvest timing to processing, each step can be a critical point when it comes to wine quality and phenolic composition. In this study, the influence of winemaking technology on resveratrol and quercetin content, as well as other polyphenolic compounds, was investigated. Resveratrol is a non-flavonoid polyphenolic stilbene synthesized by grape skin when damaged by infectious diseases or ionizing radiation. Quercetin is a phenol found in grape skins and stems and is produced to protect grapes from UV light damage. Trans-resveratrol and quercetin are known to act as antioxidants, reduce the risk of atherosclerosis and type 2 diabetes, inhibit the growth of cancer cells, and prevent the release of allergic and inflammatory molecules. However, the question was whether red wine could be enriched with these phenols using an innovative winemaking technology. The innovative idea was to completely replace the cold maceration process with maceration with the addition of wild yeast (Torulaspora delbrueckii, Td). Maceration with the addition of wild yeast (Td) offers the following advantages over traditional cold maceration: (1) higher concentrations of trans-resveratrol (>35-40%) and quercetin (>35-40%) in the final wine, (2) the new wine has a higher potential for human health, (3) the wine has a better aroma and stability due to the higher mannoprotein content, and (4) the better energy efficiency in the production process. The study of stability during storage and aging also included derivatives of benzoic acid and hydroxycinnamic acid, piceid, catechin, naringenin, rutin, kaempherol, hesperetin, and anthocyanins. The study found that younger wines had higher phenolic content, while storage of the wine resulted in a decrease in total phenolic content, especially monomeric stilbenes and quercetin.

Sr4Al6O12SO4 samples were obtained from the compound mixture formed by a solid–state reaction of Al2O3, SrSO4, and SrCO3. Samples were compacted at 100MPa to form pellets of 1 and 4cm in diameter and were sintered at 1400°C for 4 hours. The compound was analyzed by X–ray diffraction. Static immersion and wettability tests were performed to evaluate corrosion resistance in contact with Al–Si. Corrosion tests were carried out by immersion at 800, 900, and 1000°C for 24, 50, and 100 hours, while wettability was carried out at 900, 1000, and 1100°C for 2 hours. Subsequently, the samples were prepared metallographically. Samples were analyzed by optical microscopy, scanning electron microscopy, and image analysis. In general, reaction products consisting of alumina, spinel, oxides, and sulfates were found. The contact angles obtained were 124° to 135°. It is concluded that ceramic substrate Sr4Al6O12SO4 is resistant to corrosion by Al–Si alloy, since the slight thickness of the reaction products found in the samples (100μm) considering the severe conditions of the experiment: 1000°C and 100 hours of isothermal temperature. Furthermore, it can be said that Sr4Al6O12SO4 is not wettable by Al–Si alloys.

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Nickel-based superalloys are attractive to many industrial sectors (automotive, military, energy, aerospace etc.). However, their physical properties make them difficult to machining using traditional tools. Therefore, the new materials for the machining of Ni-based alloys are required. Ceramic-based composites could act as a tool to replace the current materials. The incentives for this paper are to provide an overview of existing ceramic composites and draw some conclusions that will help in solving the problem of choosing materials for processing of Ni-based superalloys. Despite the diversity of ceramic composites in this work the focus was on the SiAlON ceramic.

Phenolic compounds, present in plants, provide substantial health advantages, such as antioxidant and anti-inflammatory properties, which enhance cardiovascular and cognitive well-being. Australia is enriched with a wide range of plants with phytopharmacological potential, which needs to be fully elucidated. In this context, we analyzed leaves of aniseed myrtle (Syzygium anisatum), lemon myrtle (Backhousia citriodora), and cinnamon myrtle (Backhousia myrtifolia) for their complex phytochemical profile and antioxidant potential. LC-ESI-QTOF-MS/MS was applied for screening and characterizing these Australian myrtles’ phenolic compounds and the structure-function relation of phenolic compounds. This study identified 145 and quantified/semi-quantified 27 phenolic compounds in these Australian myrtles. Furthermore, phenolic contents (total phenolic content (TPC), total condensed tannins (TCT), and total flavonoids (TFC)) and antioxidant potential of phenolic extracts from the leaves of Australian myrtles were quantified. Aniseed myrtle was quantified with the highest TPC (52.49 ± 3.55 mg GAE/g) and total antioxidant potential than other selected myrtles. Catechin, epicatechin, isovitexin, cinnamic acid, and quercetin were quantified as Australian myrtles' most abundant phenolic compounds. Moreover, chemometric analysis further validated the results. This study provides a new insight into the novel potent bioactive phenolic compounds from Australian myrtles that could be potentially useful for functional, nutraceutical, and therapeutic applications.

One of the most concerning global environmental issues is the pollution of agricultural soils by heavy metals (HMs), especially cadmium (Cd), which not only affects human health by taking Cd-containing foods but also impacts the quality of rice. The soil's nitrification and denitrification processes, coupled with the release of volatile organic compounds by plants, raise substantial concerns. The understanding of three aspects of paddy soil under conditions of heavy-metal pollution and water management is currently limited. In this review, we summarized recent literature related to the deleterious effects of Cd on both soil processes related to the N cycle and rice quality, particularly aroma, in different water management practices. Under both continuous flooding (CF) and alternate wetting and drying (AWD) conditions, cadmium (Cd) has been observed to reduce both nitrification and denitrification processes. The adverse effects are more pronounced in continuous flooding (CF) compared to alternate wetting and drying (AWD). Similarly, the alteration in rice aroma is more significant in AWD than in CF. The precise modulation of volatile organic compounds (VOCs) by Cd, remains unclear based on the available literature. Nevertheless, HM accumulation is higher in AWD conditions compared to CF, leading to a detrimental impact on volatile organic compounds (VOCs). The literature concluded that AWD practices should be avoided in Cd contaminated fields to decrease accumulation and maintain the quality of rice. In the future, rhizospheric engineering and plant biotechnology can be used to decrease the transport of HMs from the soil to the plant’s edible parts.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

Low temperature cofired ceramics (LTCC) have conquered a niche segment in biological microelectromechanical systems (BioMEMS) during the last two decades. Since 3-dimensional assembly and rapid prototyping capability are outstanding features of the technology, bioreactors with complex geometry can easily be produced. Particularly needed functions are working electrodes, e.g. for impedance measurements and reference electrodes consisting in platinum or silver-silver chloride. Although the distinct grainy surface of thick film materials influences the double layer properties, data describing the bioelectronic interface and biocompatibility of common thick film materials are rarely published up to now. This works aims to fill this gap by studying the surface properties, composition, electrochemical properties and biocompatibility of commercially available thick film materials. It was found that thick film gold is suitable as electrode material in direct cell contact since an appropriate proliferation of the cell culture was observed. Poly(3,4-ethylenedioxythiophene) coating decreases the absolute value of the zeta potential of thick film gold from 16.55 V to 11.78 mV without any change in vitality of the cells. Thick film platinum layers have a porous structure entailing an enlargement of the effective surface by a factor of 21.6 and can be used as reference instead of silver/silver chloride, which was identified to be incompatible with cell culture. The investigations show that some commercially available cost-effective thick film materials are compatible with cell culture and the here presented data give an orientation for the use of the same in LTCC bioreactors.

The chemical investigation of the anti-yeast methanol extract from the stem bark of Terminalia mantaly led to the isolation of seven compounds: 3-O-methyl-4-O-α-rhamnopyranoside ellagic acid (1), 3-O-mehylellagic acid (2), arjungenin or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid (3), arjunglucoside or 2,3,19,23-tetrahydroxyolean-12-en-28-oïc acid glucopyranoside (4), 2α,3α,24-trihydroxyolean-11,13(18)-dien-28-oïc acid (5), stigmasterol (6), stigmasterol 3-O-β-D-glucopyranoside (7). Their structures were established by means of spectroscopic analysis and comparison with published data. Compounds 1-5 were tested in vitro for activity against three pathogenic yeast isolates, Candida albicans, Candida parapsilosis and Candida krusei. The activity of compounds 1, 2 and 4 were comparable to that of the reference compound fluconazole (MIC values below 32 µg/ml) against the three tested yeast isolates. They were also tested for inhibitory properties against four enzymes of metabolic significance: Glucose-6-Phosphate Deshydrogenase (G6PD), human erythrocyte Carbonic anhydrase I and II (hCA I and hCA II), Glutathione S-transferase (GST). Compound 4 showed highly potent inhibitory property against the four tested enzymes with overall IC₅₀ values below 4 µM and inhibitory constant (Ki) <3 µM.

Herbal Coffee is getting more popular due to its unique flavor and higher concentration of bioactive compounds, mainly polyphenols. Rosemary is a unique herb with potent antioxidant properties. A green technique called ultrasound aids in releasing bioactive substances from the plant cell wall. In this context, ultrasound-assisted herbal coffee prepared and their anti-diabetic, anti-Alzheimer, and antioxidant activities were measured while the LC/MS was used to determine the bioactive components from the herbal coffee infusion. A total of 95 secondary metabolites were putatively reported, including alkaloids, phenolic acids, and flavonoids, which we identified in the herbal coffee infusion. The total phenolic content (61.5 ± 5.1 mg GAE/g), total flavonoid content (19.3 ± 0.9 mg QE/g), and total condensed tannin (7.6 ± 0.7 mg CE/g) of herbal coffee infusion were observed to be highest of the two remaining samples. The herbal coffee extracts were used to determine all samples' antioxidant, anti-diabetic, and anti-Alzheimer activities. Using LC-MS/MS, we semi-quantified 19 phenolic metabolites. The results show numerous bioactive components in herbal coffee infusion with more potent antioxidant, antidiabetic, and anti-Alzheimer potential. Moreover, more studies must be conducted to confirm how the metabolomic profile of herbal coffee affects its flavor profile.

Broadly speaking, binominal and biverbal lexical constructions have been studied independently in different research traditions and frameworks. It is true that the two do not necessarily have overlapping areal distributions, but the fundamental question remains whether Indo-European NN compounds and Transeurasian VV compounds have nothing in common. From a purely theoretical perspective also, the cross-categorial parallelism is worthy of serious investigation because a theory of the process of compounding that inherits the spirit of X-bar theory strives to capture commonalities among various compounding patterns and category-specific constraints observed within and across languages. Against this background, a cross-categorial comparison, not within but across languages, is made of coordinative binominal and biverbal constructions. NN and VV coordinate compounds from English and Japanese are examined in detail using the methodology of contrastive morphology and decompositional lexical semantics. It is shown that dvandva is possible not only in NN but also in VV coordinate compounds and furthermore that the dvandva-appositive distinction in NN coordinate compounds recurs in VV coordinate compounds.

Multi-wire saw machining (MWSM) used for slicing hard-brittle materials in semiconductor, is an important material removal process that uses free abrasives. Cutting model of single-wire saw machining (SWSM) is the basis of MWSM, and the material removal mechanism of SWSM can better understand than MWSM. Mathematical model (includes brittle fracture and plastic deformation) is presented in this paper for SWSM ceramic with abrasives. This paper determines the effect of various machining parameters on the removal of hard-brittle materials. For brittle fracture of SWSM ceramics, the minimum of the strain energy density is used as a fracture criterion. The material removed of SWSM ceramics due to plastic deformation is calculated using the equations of motion. Actual wire-sawing experiments are conducted to verify the results from the developed mathematical model. Theoretical results agree with experimental data and practical experience. The developed mathematical model shows that brittle fracture plays a major concern role in material removed of SWSM ceramics. Wire speed and working load have positively correlated with material removed of SWSM ceramics. The coefficient of friction is low, a lateral crack, which propagates almost parallel to the working surface, leads to more brittle fracture and material removed is increased on SWSM ceramics.

Magnetic ceramic nanoparticles system xTm2O3-(1-x)alpha-Fe2O3 (x=0.1 and 0.5) was synthesized by mechanochemical activation starting from hematite and thulium oxide precursors and characterized by transmission Mӧssbauer spectroscopy. The Mӧssbauer spectra were typically analyzed considering 1-3 sextets, corresponding to hematite (with and without thulium doping) and a doublet, representing thulium iron perovskite (thulium orthoferrite). The magnetic hyperfine fields (BHF) and doublet abundance were studied as function of the ball milling time (BMT) for both molar concentrations employed. The results are consistent with the formation of solid solutions in the investigated system. The mixed-oxide nanoparticle system synthesized may have important applications in displays, sensors and photovoltaics, and is paving the way for emerging utilizations related to mechanically flexible electronics.

The increase in global warming due to NOx, CO2, and CH4 harmfully different ecosystems and significantly prejudice world life. A promising methodology in this sense is the pollutant conversion into valuable chemicals from photocatalytic processes by reusable photocatalyst. In this way, the present work aimed to produce a Nb2O5 photocatalyst nanofibers system to convert CO2 by the electrospinning method. Based on the collected data, the nanofibers calcination at 600°C for 2 h resulted in the best condition to obtain a homogeneous surface with an average diameter of 84 nm. As a result, the Nb2O5 nanofibers converted CO2 mostly into CO and CH4, reaching values around 8.5 μmol g−1 and 0.55 μmol g−1, respectively.

In municipal waterworks large amounts of waste in the form of sludge have to be discarded. This investigation focuses on the processing of ceramic floor tiles incorporated with a municipal waterworks sludge. Four floor tile formulations containing up to 10 wt. % of the municipal waterworks sludge in replacement of kaolin were prepared. The floor tile processing route consisted of dry powder granulation, uniaxial pressing, and firing between 1190 and 1250 °C using a fast-firing cycle (<60 min). The densification behavior and technological properties of the floor tile pieces as function of the sludge addition and firing temperature were determined. The development of the microstructure was followed by XRD and SEM/EDS. The results show that the replacement of kaolin with municipal waterworks sludge, in the range up to 10 wt. %, allows the production of ceramic floor tiles (group BIb and group BIIa, ISO 13006 Standard) at lower firing temperatures. These results suggest a new possibility for valorization of municipal waterworks sludge with many economical and environmental benefits.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

The structure of arylpiperazine moieties as an important pharmacophore could generate wide pharmacological activities．Arylpiperazine derivatives referred in this paper possessed antitumor activity. The title compounds were crystallized by slow evaporation. 2-(4-(2-(4-Phenylpiperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione(1), 2-(4-(2-(4-(4-Bromophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (2) and 2-(4-(2-(4-(4-Chlorophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (3) crystallizes in the triclinic space group P-1 with two molecules in the unit cell. The unit cell parameters for 1 are a = 6.9159(14) Å, b = 9.999(2) Å, c = 16.925(3) Å, α = 88.25(3)°, β = 85.14(3) °, γ = 79.22(3) °. The unit cell parameters for 2 are a = 6.9995(14) Å, b = 9.919(2) Å, c = 17.671(4) Å, α= 97.55(3)°, β = 92.19(3) °, γ = 102.23(3) °. The unit cell parameters for 1 are a = 6.9872(14) Å, b = 9.863(2) Å, c = 17.557(4) Å, α=96.81(3)°, β = 91.89(3) °, γ = 101.74(3) °. Pi-pi interactions were observed between molecules, and compound 2 and 3 showed halogen interactions between molecules nearby, which was different from compound 1.

Two secondary waste materials, municipal incinerator bottom ash (MIBA) and sewage sludge ash (SSA), were mixed with clay for ceramic manufacturing in this study. Specimens with 5 different MIBA replacement amount of 0%, 5%,10%, 15%, and 20%(wt) and 3 different SSA replacement amount of 0%, 10%, and 20%(wt) were prepared and then a series of tests and analysis were conducted to investigate how the two materials affect the quality of the final product and to what extent. It concludes that a mix with up to 20% of SSA and 5% of MIBA could result in quality tiles complying with specifications for interior or exterior flooring applications at certain kiln temperatures.

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

This topical review describes the results of recent research into and development of silicon nitride, a ceramic material with unique properties. The outcome of this ongoing research strongly encourages the use of monolithic silicon nitride and coatings as contemporary and future biomaterial for a variety of medical applications. Crystallographic structure, synthesis and processing of monolithic structures and coatings, and examples of their medical applications are covered that relate to spinal, orthopedic and dental implants, bone grafts and scaffolds, platforms for intelligent synthetic neural circuits, antibacterial and antiviral particles and coatings, optical biosensors, and nano-photonic waveguides for sophisticated medical diagnostic devices. The examples provided show convincingly that silicon nitride is destined to become a leader to replace titanium and other entrenched biomaterials in many fields of medicine.

Fired bricks have shown tremendous potential as a construction material due to their properties. However, their use required some specifications in terms of quality, resistance, and durability. In developing countries, the lack of tools to make test specimens leads to many defects in these brick specimens responsible for low durability and weak precision during mechanical tests and shrinkage. In this study, a simple and traditional method of making test bricks is presented. This simple method allows the production of bricks with the required properties. This method is especially efficient for a firm or semi-soft pastes consistency. The handmade pastes do not stick into the walls of the mold like the case of steel molds and it gives specimens with standard shape, smooth surface, and sharp edges. The resulting fired bricks exhibit high mechanical strength comparable and even better than those of conventional methods.

(1) Background: Grapes and their associated by-products (as grape pomace, GP) stand out for their polyphenol content, which makes them a source of bioactive compounds with antioxidant capacity. The aim of this research was to determine if the inclusion of 50 g/kg of GP in the diet of hens could enrich egg with antioxidants and to study its effect on internal and external egg quality parameters. (2) Methods: A trial was conducted with two genetic lines of hens, which were fed either a control diet or a diet containing 50 g/kg of GP. Performance, internal and external egg quality, and egg yolk content of vitamins E and A, and gallic acid were determined; (3) Results: In eggs laid by hens fed GP diet, Haugh units and yolk colour score were enhanced, and eggshell became thinner, but without affecting the breaking strength. No dietary effect was observed on vitamin contents in yolk. Higher gallic acid content was observed in yolk of eggs laid by hens fed the GP diet, suggesting that some dietary phenolic compounds could be transferred to the eggs. Hen genetics influenced egg weight, albumen Haugh units, shell thickness and α- and γ-tocopherol concentration in yolks; (4) Conclusions: Dietary inclusion of GP improved the internal quality of eggs, enriching yolks with a phenolic compound, but reduced shell thickness.

Silybin is a natural compound extensively studied for its hepatoprotective, neuroprotective and anti-cancer properties. Envisioning the enhancement of silybin potential by suitable modifications in its chemical structure, here, a series of new 7-O alkyl silybins derivatives were synthesized by Mitsunobu reaction starting from the silybins and tyrosol-based phenols, such as tyrosol (TYR, 3), 3-methoxytyrosol (MTYR, 4) and 3-hydroxytyrosol (HTYR, 5). This research sought to explore the antioxidant and anticancer properties of new eighteen derivatives and their mechanisms. In particular, the antioxidant properties of new derivatives outlined by DPPH assay, showed a very pronounced activity depending on the tyrosyl moiety (HTYR&gt;MTYR&gt;&gt;TYR). A significant contribution of the HTYR moiety was observed for silybins and 2,3-dehydro-silybin based derivatives. According to the very potent antioxidant activity, 2,3-dehydro-silybin derivatives 15ab, 15a and 15b exerted the most potent anticancer activity in human prostate cancer PC-3 cells. Furthermore, flow cytometric analysis for cell cycle and apoptosis revealed that 15ab, 15a and 15b induce strong G1 phase arrest and increase late apoptotic population in PC-3 cells. Additionally, western blotting for apoptotic marker cleaved caspase-3 confirmed apoptosis induction by these silybin derivatives in PC-3 cells. These findings hold significant importance in the investigation of anticancer properties of silybin derivatives and strongly encourage swift investigation in pre-clinical models and clinical trials.

The purpose of the study is to analyse and to identify specific structural characteristics of melanocytic nevi. So, for better conclusions, using the optical microscope, could be possible a proper describtion related melanocytic nevi, reffering to youth pacients. In this research direction, good to mention that in a human individual life, play a significant role, different factors. That include in line, genetic, epigenetic, microbiomic, and proteomic factors. Future directions refers to preventive and prophylactic methods.

Background: Lithium di-silicate dental ceramics bonding, realized by using different resins, is strictly dependent on micro-mechanical retention and chemical adhesion. The aim of this in vitro study was to investigate the capability of a 1070 nm fiber laser for their surface treatment. Methods: Samples were irradiated by a pulsed fiber laser at 1070 nm with different parameters (Peak Power from 5 kW to 5 kW, RR 20 kHz, speed from 10 to 50 mm/s, total Energy Density from 1.3 to 27 kW/cm²) and the thermal elevation during the experiment was recorded by a Fiber Bragg Grating (FBG) temperature sensor. Subsequently, the surface modifications were analysed by optical microscope, Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Results: With a Peak Power of 5 kW, RR of 20 kHz and speed of 50 mm/s, the microscopic observation of the irradiated surface showed increased roughness with small areas of melting and carbonization. EDS analysis revealed that, with these parameters, there are no evident differences between laser-processed samples and controls. Thermal elevation during laser irradiation ranged between 5 °C and 9 °C. Conclusions: 1070 nm fiber laser can be considered as a good device to increase the adhesion of Lithium di-silicate ceramics.

The present paper investigates flaw strength distributions established using various flexural tests on batches of SiC bar test specimens: 4-point bending as well as 3-point bending with different span lengths. Flaw strength is given by the elemental stress operating on the critical flaw at fracture of a test specimen. Fracture inducing flaws and their locations are identified by fractography. A single population of pores was found to dominate fracture. The construction of diagrams of p-quantile vs elemental strengths was aimed at assessing the Gaussian nature of flaw strengths. Then, empirical cumulative distributions of strengths were constructed using the normal distribution function. Weibull cumulative probability distributions were derived from the mean and the standard deviation using the first moment equation. Agreement was obtained between both Weibull and normal flaw strengths distributions. The cumulative distributions for the different bending tests were predicted satisfactorily from the flaw strength density function using the elemental strength model. Flaw strength distributions that include potential weaker flaws encountered in larger test pieces are extrapolated using the p-quantile diagrams. Implications are discussed about the pertinence of an intrinsically representative flaw strength distribution, about failure predictions, about size effects, and about the significance of flaw spatial distributions.

Aiming to reveal the kinetic characteristics of ceramic ball grinding of fine magnetite comprehensively, two types of ceramic balls ground with the same filling rate and total weight as steel balls were researched. The results show that the breakage rate of ceramic ball grinding is only half of that of steel ball grinding with the same media filling rate. With the same total media weight and the feed size less than 0.212 mm, the breakage rate of the ceramic ball grinding approaches the steel ball grinding and is 21.43% higher than that of the steel ball grinding. The main crushing form of magnetite changed from impact to abrasion in ceramic ball grinding compared with steel ball grinding, which significantly affected the value of the zero-order output constant a. Consequently, there is a noticeable difference in the variation of the parameter β related to the fines generation rate of the ceramic ball grinding compared with the steel ball grinding.

Considering that the electric refrigeration temperature range of 0.94BNT-0.06BT ceramic materials is 100~140˚C, the electric refrigeration performance of the 0.94BNT-0.06BT ceramic material system was modified by LiNbO3 doping to reduce the cooling temperature. As a result, the refrigeration temperature range of the 0.94BNT-0.06BT ceramic material system was lowered to 25~80 ˚C, achieving its cooling effect near room temperature, and in this temperature range, the adiabatic temperature changes ∆T&gt;0.6K.

Abstract: This work for the first time investigated the densification of multi-doping zirconia ceramic body with organic coating powders for solid electrolyte of solid oxide fuel cells via online imaging technology. The densification results show the initial stage plays a key role in the sintering. It can be found the covered organic PVA (polyvinyl acetate) supplies a potential kinetics to the initial densification during sintering. As a result, a kinetic function of densification in the initial stage was suggested. Furthermore, a novel sintering model with six sub-stages is developed for polycrystalline zirconia ceramics. The findings would be a valuable reference for predicting final temperature of sintering, the equivalent strain during the sintering process, as well as optimizing the densification behavior.

Acoustic emission (AE) has proven to be a very useful technique for determining damage in ceramic matrix composites (CMCs). CMCs rely on various cracking mechanisms which enable non-linear stress-strain behavior with ultimate failure of the composite due to fiber failure. Since these damage mechanisms are all micro-fracture mechanisms, they emit stress waves ideal for AE monitoring. These are typically plate waves since for most specimens or applications one dimension is significantly smaller than the wavelength of the sound waves emitted. By utilizing the information of the sound waveforms captured on multiple channels from individual events, the location and identity of the sources can often be elucidated. The keys to the technique are the use of wide-band frequency sensors, digitization of the waveforms (modal AE), strategic placement of sensors to sort the data and acquire important contents of the waveforms pertinent for identification, and familiarity with the material as to the damage mechanisms occurring at prescribed points of the stress history. The AE information informs the damage progression in a unique way which adds to the understanding of the process of failure for these composites. The AE methodology was applied to composites tested in fatigue at different frequencies where identification of when and where AE occurred coupled with waveform analysis leads to source identification and failure progression.

The HS-SPME GC-MS analysis of the volatile compounds adsorbed at the outer surface of lemon and grapefruit pectins obtained via hydrodynamic cavitation of industrial waste streams of lemon and grapefruit peels in water only suggests important new findings en route to understanding the powerful and broad biological activity of these new pectic materials. In agreement with the ultralow degree of esterification of these pectins, the high amount of highly bioactive α-terpineol and terpinen-4-ol points to limonene decomposition catalyzed by residual citric acid in the citrus waste peel residue of the juice industrial production.

This review focuses on the synthesis and biological activity of flavones and their related flavonoidic compounds: flavonols and aurones. Among the biological activities of flavones and aurones, the anticancer, antioxidant and antimicrobial properties are highlighted and detailed in this review. The most applied method for the synthesis of flavones and aurones is based on the oxidative cyclisation of o-hydroxychalcones. Depending on the reaction conditions and the structure of the precursor, in some cases several cyclization products result simultaneously: flavones, flavanones, flavonols and aurones. Based on the literature data and the results obtained in our research group, our aim is to highlight the most promising methods for the synthesis of flavones, as well as the synthetic routes for the other structurally related cyclization products, hydroxyflavones and aurones, considering that in practice it is difficult to predict which is the main or exclusive cyclisation product of o-hydroxychalcones under certain reaction conditions.

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

This study provides a novel method to prepare metal-ceramic composites from magnetically selected iron ore using microwave heating. By introducing three different microwave susceptors (Activated Carbon, SiC, and a mixture of Activated Carbon and SiC) during the microwave process, effective control of the ratio of metallic and ceramic phases has been achieved easily. The effects of the three susceptors on the microstructure of the metal-ceramics and the related reaction mechanisms were also investigated in detail. The results show that the metal phase (Fe) and ceramic phase (Fe2SiO4, FeAl2O4) can be maintained, but the metal phase to ceramic phase changed significantly. In particular, the microstructures appeared as well-distributed nanosheet structures with diameters of ~400 nm and thicknesses of ~20 nm when SiC was used as the microwave susceptor.

Reversible protonic ceramic cells (rPCCs) combine two different operation regimes, fuel cell and electrolysis cell modes, which allow reversible chemical-to-electrical energy conversion at reduced temperatures with high efficiency and performance. Here we present novel technological and materials science approaches, enabling a rPCC with symmetrical functional electrodes to be prepared using a single sintering step. The response of the cell fabricated on the basis of P–N–BCZD|BCZD|PBN–BCZD (where BCZD = BaCe_0.5Zr_0.3Dy_0.2O_3–δ, PBN = Pr_1.9Ba_0.1NiO_4+δ, P = Pr₂O₃, N = Ni) is studied at different temperatures and water vapor partial pressures (pH₂O) by means of volt-ampere measurements, electrochemical impedance spectroscopy and distribution of relaxation times analyses. The obtained results demonstrate that symmetrical electrodes exhibit classical mixed-ionic/electronic conducting behavior with no hydration capability at 750 °C; therefore, increasing the pH₂O values in both reducing and oxidizing atmospheres leads to some deterioration of their electrochemical activity. At the same time, the electrolytic properties of the BCZD membrane are improved, positively affecting the rPCC’s efficiency. The electrolysis cell mode of the rPCC is found to be more appropriate than the fuel cell mode under highly humidified atmospheres, since its improved performance is determined by the ohmic resistance, which decreases with pH₂O increasing.

The difficult current environmental situation, caused by construction industry residues containing ceramic materials could be improved by using these materials as recycled aggregates in mortars, with their processing causing a reduction in their use in landfill, contributing to recycling and also minimizing the consumption of virgin materials. Although some research is currently being carried out into recycled mortars, little is known about their stress-strain (σ-ε); therefore this work will provide the experimental results obtained from recycled mortars with recycled ceramic aggregates (with contents of 0, 10, 20, 30, 50 and 100%), such as: the density, the compression strength, as well as the σ-ε curves representative of their behavior. The values obtained from the analysis process of the results are those of: σ (elastic ranges and failure maximum), ε (elastic ranges and failure maximum), and Resilience and Toughness; in order to finally obtain, through numerical analysis, the equations to predict their behavior (related to their recycled content). At the end of the investigation it is established that mortars with recycled ceramic aggregate contents of up to 20% could be assimilated just like mortars with the usual aggregates, and the prediction equations produced could be used in cases of similar applications.

In this paper glass crystallization behavior of 50ZnO:47B2O3:3Nb2O3:0.5Eu2O3 (G-0h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of resulted glass-ceramics were also investigated. By XRD and TEM analysis crystallization of several crystalline phases have been proved (α-Zn3B2O6, β-Zn3B2O6 and ZnNb2O6). By calculating of crystal parameters it was found that europium ions are successfully incorporated in the β-Zn3B2O6. Photo-luminescent spectra show an increased emission in the resulting glass-ceramic samples as compared with the parent glass sample because of the higher asymmetry of Eu3+ ions in the crystalline phases obtained. It was established that the optimum emission intensity is registered for glass-ceramic sample obtained after 25 hours heat treatment of the parent glass.

Self-healing ceramic composites are promising smart materials for high-temperature applications. To better understand their behaviors under service conditions, numerous studies have been performed both experimentally and numerically, and kinetics parameters such as activation energy and frequency factor are reported to be indispensable for investigating healing phenomena. Here, we propose a method for determining the kinetic parameters of self-healing ceramic composites based on the oxidation kinetics model of strength recovery. These parameters are determined by an optimization method using experimental strength recovery data under various healing temperatures and times and microstructural features on the fractured surfaces. Alumina and mullite matrix-based self-healing ceramic composites, such as Al2O3/SiC, Al2O3/TiC, Al2O3/Ti2AlC (MAX phase), and mullite/SiC, were selected as target materials. The theoretical strength recovery behaviors of the cracked specimens obtained from the determined kinetic parameters were compared with the experimental results. The determined parameters are within the previously reported range, and the predicted strength recovery behaviors are reasonably agreed with the experimental values. The proposed method can also be applied to other self-healing ceramics with matrices reinforced with different healing agents to evaluate oxidation rate, crack healing rate, and theoretical strength recovery behaviors for designing self-healing materials used in high temperature applications. Furthermore, the healing ability of composites can be fairly discussed regardless of the type of strength recovery test.

In the present work, the state of the art of the most common additive manufacturing (AM) technologies used for the manufacturing of complex shape structures of graphene-based ceramic nanocomposites, ceramic and graphene-based parts is explained. A brief overview of the AM processes for ceramic, which are grouped by the type of feedstock used in each technology, is presented. The main technical factors that affect the quality of the final product were reviewed. The AM processes used for 3D printing of graphene-based materials are described in more detail; moreover, some studies in a wide range of applications related to these AM techniques are cited. Furthermore, different feedstock formulations and their corresponding rheological behaviour were explained. Additionally, the most important works about the fabrication of composites using graphene-based ceramic pastes by Direct Ink Writing (DIW) are disclosed in detail and illustrated with representative examples. Various examples of the most relevant approaches for the manufacturing of graphene-based ceramic nanocomposites by DIW are provided.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Chloroquine (CQ) and its derivate hydroxychloroquine (HCQ), the compounds with recognized ability to suppress autophagy, have been tested in experimental works and in clinical trials as adjuvant therapy for the treatment of cancers of different origin to increase the efficacy of cytotoxic agents. Such strategy can be effective to overcome the resistance to standard chemotherapy or anti-angiogenic therapy. This review presents the results of combined application of CQ/HCQ with conventional chemotherapy drugs (doxorubicin, paclitaxel, platinum-based compounds, gemcitabine, tyrosine kinases and PI3K/Akt/mTOR inhibitors, and other agents) for the treatment of different malignancies obtained in experiments on cultured cancer cells and on animal xenograft models, with a few examples of clinical trials. The effects of such approach on viability of cancer cells and tumor growth, as well as autophagy-dependent and independent molecular mechanisms underlying cellular responses of cancer cells to CQ/HCQ are summarized. Although the majority of experimental studies in vitro and in vivo have shown that CQ/HCQ can effectively sensitize the cancer cells to cytotoxic agents and increase the potential of chemotherapy, the results of clinical trials are often inconsistent. Although pharmacological suppression of autophagy remains a promising tool for increasing the efficacy of standard chemotherapy, the development of more specific compounds is required.

This work aimed to synthesize new N-rich triazole compounds. In this article we describe the synthesis of three different 1,2,4-triazole-based systems starting from 1,3-diaminoguanidine hydrochloride monohydrate. The structure of the obtained crystals was established by single-crystal X-Ray diffraction. The high nitrogen content of the synthetized compounds makes them building blocks for the application in the High-Energy-Density material science.

Copper-catalyzed and organocopper-involved reactions are of great significance in organic synthesis. To have a deep understanding of the reaction mechanisms, the structural characterizations of organocopper intermediates become indispensable. Meanwhile, the structure-function relationship of organocopper compounds would advance rational design and development of new Cu-based reactions and organocopper reagents. Compared to the mono-carbonic ligand, the C,N- and C,C-bidentate ligands better stabilize the unstable organocopper compounds. The bidentate ligands can chelate to the same copper atom via ?2-mode, forming a mono-cupra-cyclic compounds with at least one acute C-Cu-C angle. When the bidentate ligands bind to two copper atoms via ?1-mode at each coordinating site, the bimetallic macrocyclic compounds will form nearly linear C-Cu-C angles. The anionic coordinating sites of the bidentate ligand can also bridge two metals via ?2-mode, forming organocopper aggregates with Cu-Cu interactions and organocuprates with contact ion pair structures. The reaction chemistry of some selected organocopper compounds is highlighted, showing their unique structure-reactivity relationships.

In this paper, we investigate the structural, microstructural, dielectric, and energy storage properties of Nd and Mn co-doped Ba0.7Sr0.3TiO3 [(Ba0.7Sr0.3)1-xNdxTi1-yMnyO3 (BSNTM) ceramics (x = 0, 0.005, and y = 0, 0.0025, 0.005, and 0.01)] via a defect dipole engineering method. The complex defect dipoles (MnTi"-VO∙∙)∙ and (MnTi"-VO∙∙) between acceptor ions and oxygen vacancies capture electrons, enhancing the breakdown electric field and energy storage performances. XRD, Raman spectroscopy, and microscopic investigations of BSNTM ceramics revealed the formation of a tetragonal phase, increased oxygen vacancies, and reduced grain size with Mn dopant, respectively. The BSNTM ceramics with x=0.005 and y=0 exhibit a high dielectric constant of 2058 and a dielectric loss of 0.026 at 1 kHz. These values gradually decreased to 1876 and 0.019 for x=0.005 and y=0.01 due to the Mn2+ ions at Ti4+-site, which facilitates the formation of oxygen vacancies, and prevents the decrease of Ti4+. In addition, the defect dipoles act as a driving force for depolarization to tailor the domain formation energy and domain wall energy, which provides a high difference between the maximum polarization of Pmax and remnant polarization of Pr (ΔP=10.39 µC/cm2). Moreover, the complex defect dipoles with optimum oxygen vacancies in BSNTM ceramics can provide not only a high ΔP but also reduce grain size, which together improve the breakdown strength from 60.4 to 110.6 kV/cm, giving rise to a high energy storage density of 0.41 J/cm3 and high efficiency of 84.6% for x=0.005 and y=0.01. These findings demonstrate that defect dipoles engineering is an effective method to enhance the energy storage performance of dielectrics for capacitor applications.

The current investigation presents porous ceramic materials prepared of cenospheres prepared by spark plasma sintering. The impact of sintering temperature, mould diameter (20 and 30 mm diameter) and cenosphere size on the properties of the sintered material was investigated. Shrinkage of the samples during sintering started at 900 °C. Sample shrinkage during sintering increases with increasing temperature and decreases with increasing mould size; increasing sample sintering temperature increases the apparent density of all sample series CS 63-150 µm in 20 mm mould from 0.97 to 2.3 g·cm-3 at 1050 - 1300 °C, in 30 mm mould 0.81 - 1.87 g·cm-3 at 1050 - 1200 °C, in 50 mm mould 0.54 - 0.75 g·cm-3 at 1050 - 1150 °C, while CS 150-250 µm in 20 mm mould 0.93 - 1.96 g·cm-3 at 1050 - 1200 °C. Total porosity decreases from 61.5% to 3.9% with increasing sintering temperature from 1050 to 1250 °C, while open porosity reduces at lower temperatures, with closed porosity being highest in samples sintered at 1150 °C. When the sintering temperature increases from 1050 to 1300 °C, the compressive strength of the CS 63-150 samples produced in a 20 mm mould increases from 11 MPa to 312 MPa. These results correlate with the Rice model, which describes an exponential dependence of compressive strength on material porosity and fully dense material compressive strength.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Franklinite-Zincochromite-Gahnite solid solutions have been prepared by ceramic or coprecipitation method and its pigmenting capacity as cool ceramic pigments in different glazes (double and single firing frits and porcelain frit) was studied. XRD, UV-Vis-NIR diffuse reflectance, CIEL*a*b* colour analysis, bandgap measurement and the photocatalytic activity over the Orange II azoic dye were carried out for the characterization of samples. Following criteria of high red colouring capacity and high NIR reflectance at minimum Cr amount, Zn(Fe1.8Cr0.2), Zn(Al1.5Cr0.5) and Zn(Al1.3Cr0.5Fe0.2)O4 turn out to be the optimal compositions for an intense reddish cool pigment. All powders show a direct semiconductor behaviour with bandgap around 2 eV, falling in the visible range (620 nm), and according to literature, the associated photocatalytic activity over Orange II with visible light irradiation is moderate in all cases, but the Franklinite-Zincochromite Zn(Fe1.8Cr0.2) stands out.

Although CAD/CAM ceramics present a promising alternative to metal-ceramic fixed dental prostheses, little is known about their mid- and long-term clinical performance. This systematic review aims to estimate the survival and success rates and describes the underlying complication characteristics for CAD/CAM tooth-supported fixed dental prostheses (FDPs). We systematically searched MEDLINE and Web of Science to find relevant prospective studies with a follow-up of at least one year. We estimated pooled 1-, 5- and 10-year survival and success rates by combining the collected data in a Poisson regression model. Descriptive statistics were conducted to evaluate the distribution of failures and complications in the included studies. Risk of bias for the included studies was assessed with an adapted checklist for single-arm trials. Pooled estimated 1-, 5-, and 10-year survival rates ranged from 93.80% to 94.66%, 89.67% to 91.1%, and 79.33% to 82.20%, respectively. The corresponding success rates, excluding failures but including any other types of intervention, were 94.53% to 96.77%, 90.89% to 94.62%, and 81.78% to 89.25%. Secondary caries was the most frequent cause of failure, followed by chipping of the veneering. The most common cause of complication, excluding failures but requiring intervention, was chipping of the veneering. Risk of bias was generally acceptable for the included studies, with 7 studies associated with low risk of bias, 8 studies with a moderate risk of bias, and 3 studies with serious risk of bias. The current meta-analysis on CAD/CAM supported FDPs revealed satisfying survival and success rates for up to 10 years of exposure. More prospective studies focusing on long-term performance are needed to strengthen the evidence currently available in the literature.

Selection of co-belonging fragments from the numerous ceramic findings of an archaeological excavation remains a difficult process of questionable effectiveness, based exclusively on the experience and patience of the conservators. While the screening of the fragments is a central prerequisite and the most important stage of the process of vase reconstruction, established methods based on scientific criteria and guaranteed efficiency for the detection of co-belonging ceramic fragments suggested in the bibliography, do not exist. On the contrary, for methods dealing with the assembly of vases from co-belonging fragments, which is a secondary process that can be done more easily and effectively in an empirical way, there exist numerous studies based on fragment morphology. However, even these are also not implemented because of the time requirements, sheer volume and complexity of the proposed methods, in order for them to be applicable in practice. The proposed methods in this paper are based on thermoremanent magnetization (A/m), which is calculated from the weak magnetic field measurements by a fluxgate-sensor/magnet apparatus forming a three-dimensional orthogonal system. Experimental measurements from fragments of 6 vases show that the magnetization magnitude of co-belonging fragments display similar values, despite the magnetic anisotropy of the ceramic material, since these belong to vases that are made of the same clay and fired under the same conditions. This is the criterion for finding ceramic fragments of the same vase from archaeological excavations. The thermoremanent magnetism directionality of fragments, which is aligned along the geomagnetic field at the same place and time during the vase firing process, as it is configured by their rotational symmetry, defines the position of the fragments on the body of the 6 vases. The shape of the original vase can be reconstructed when only a few non adjacent fragments are available. The proposed measurement apparatus can be used for the construction of a useable portable magnetometer specialized for ceramic surface measurements to achieve the above objectives.

An especially important species in southern Brazil, yerba mate (Ilex paraguariensis) is traditionally consumed as tea, chimarrão and tererê. Yerba mate consumption has been stimulated by scientific discoveries that have identified high concentrations of bioactive compounds and their health benefits. There are no studies or scientific evidence to certify or guarantee stability of these compounds’ concentrations during different years in the same plants. We were interested in quantifying caffeine, theobromine, total phenolic compounds and proteins concentrations in leaves of yerba mate genotypes and their stability in the same plants over four consecutive years. Mature leaves from yerba mate genotypes selected on a provenance and progenies trial were collected in August of 2015, 2016, 2017 and 2018. Methylxanthines (caffeine and theobromine), total phenolic compounds and total protein contents were quantified. Our results indicate large variations between genotypes regarding caffeine (0.035 to 2.385 g 100 g^-1), theobromine (0.0004 to 1.772 g 100 g^-1), total phenolic compounds (7.028 to 9.424 g 100 g^-1) and proteins (10.39 to 16.58 g 100 g^-1) contents, and also high stability of those compounds over the four evaluated years. A great variation of the studied bioactive compounds in different Ilex paraguariensis genotypes was found and its stability over four consecutive years was showed.

One of the areas of research on materials for thin-film solar cells focuses on replacing In and Ga with more earth-abundant elements. In that respect, chalcostibite (CuSbS2) is being considered as a promising environmentally friendly and cost-effective photovoltaic absorber material. In the present work, single CuSbS2 phase have been synthesized directly by a short duration (2 h) mechanochemical synthesis step starting from mixtures of elemental powders. X-ray diffraction analysis of the synthesized CuSbS2 powders revealed a good agreement with the orthorhombic chalcostibite phase, space group Pnma, and a crystallite size of 26 nm. Particle size characterization revealed a multimodal distribution with a median diameter ranging from of 2.93 m to 3.10 m. The thermal stability of the synthesized CuSbS2 powders was evaluated by differential thermal analysis. No phase change was observed by heat treating the mechanochemically synthesized powders at 350 C for 24 h. By UV-VIS-NIR spectroscopy the optical bandgap was determined to be 1.41 eV, suggesting that the mechanochemically synthesized CuSbS2 can be considered suitable to be used as absorber materials. Overall, the results show that the mechanochemical process is a viable route for the synthesis of materials for photovoltaic applications.

Medicinal mushrooms have got much attention from biologists in the last decades. Leucocalocybe mongolica Imai remains one of the famous clinical and edible mushrooms used in traditional Chinese medicine and Mongolian medicine to treat various diseases. It also commonly consumes in Chinese and Mongolian daily dishes. Numerous biochemical components exist in L. mongolica, especially in the fruiting bodies include; polysaccharides, sterol, lectins, laccase, amino acids, terpenes, volatile compounds, and so on. These biomedical components possess a lot of medicinal properties and provide diverse therapeutical effects for human health, such as anti-tumor activity, antiproliferative activity, anti-diabetes properties, hypotensive effect, hepatoprotective effect, antioxidant activity, cardioprotective effect, and so on. However, this review's main objectives are to illustrate some basics about the bioactive components in L. mongolica and its pharmacological effects on the human body. In addition to giving forward some suggestions for future research on this medicinal mushroom.

Several studies explore in depth the biochemistry and genetics of the pigments present in Fusarium graminearum but there is a need to discuss about their relationship with the mold’s observable surface color pattern variation throughout its lifecycle. Furthermore, they require basic cataloguing and description of their major features known so far. Colors are a viable alternative to size measurement in growth studies. When grown on yeast extract agar (YEA) at 25 °C, F. graminearum initially exhibits a whitish mycelium, developing into a yellow-orange mold by the sixth day and then turning into wine-red. The colors are likely due to accumulation of the golden yellow polyketide aurofusarin and the red rubrofusarin, but the carotenoid neurosporaxanthin possibly play also a major role in the yellow or orange coloration. Torulene might contribute for red tones but it perhaps ends up being converted into neurosporaxanthin. Culmorin is also present but it does not contribute for the color, though it was initially isolated in pigment studies, and there is the 5-deoxybostrycoidin-based melanin, but it occurs mostly in the teleomorph’s perithecium. There is still a need to chemically quantify the pigments throughout the lifecycle, analyze their relationships and how much each impacts F. graminearum surface color.

Background: Antibiotic-containing carrier systems are one option that offers the advantage of releasing active ingredients over a longer period of time. In vitro sustained drug release from a carrier system consisting of microporous β-TCP ceramic and alginate has been reported in previous works. Alginate dialdehyde (ADA) gelatin gel showed both better mechanical properties when loaded into a β-TCP ceramic and higher biodegradability than pure alginate. Methods: Dual release of daptomycin and BMP-2 was measured on days 1, 2, 3, 6, 9, 14, 21, and 28 by HPLC and ELISA. After release, the microbial efficacy of the daptomycin was verified and the biocompatibility of the composite was tested in cell culture. Results: Daptomycin and the model compound FITC protein A (n=30) were released from the composite over 28 days. A Daptomycin release above the minimum inhibitory concentration (MIC) by day 9 and a burst release of 71.7 ± 5.9 % were observed in the loaded ceramics. Low concentrations of BMP-2 were released from the loaded ceramics over 28 days.

To understand the enhanced protection mechanism of CoCrNiAlY-YSZ-LaMgAl11O19 dou-ble-layer ceramic coating with aluminum plating, a finite element simulation method was used to simulate the distribution of thermal stress in the coating in all directions. The results show that in the air exposure of the un-aluminized coating, high temperature causes a large radial thermal stress on the surface of the LaMgAl11O19 (LMA) layer, and it increases with the increase in temperature, which is the main reason for the initiation of axial cracks. After arc aluminum plating, the aluminum plating layer effectively inhibited the volume shrinkage of the coating through good adhesion to the coating and internal diffusion, the thermal stress of the coating was considerably reduced, and the CoCrNiAlY-YSZ-LMA coating had an effective enhancement and protection effect; however, there was still a certain amount of shear thermal stress inside the LMA layer, the top of the crack, and the bottom of the crack. This thermal stress caused the initi-ation of radial microcracks in the LMA layer, which also becomes a risk point for the failure of the aluminum coating.

The phase composition design principle is introduced to obtain balanced properties of ionic conductivity and thermo-tolerant for zirconia solid electrolytes used in solid oxide fuel cells (SOFCs). The zirconia ceramic solid electrolytes are fabricated by two-step free sintering. With increasing Y/Mg ionic ratio from 1.78:1 to 1.88:1, the content of monoclinic phase fluctuates little (±3%). The ionic conductivity, including the total electrical resistance; grain electrical resistance and grain boundary electrical resistance at 1223K, are all gradually declining with the increasing of Y/Mg ionic ratio. Furthermore, the enrichment of Mg ion in grain boundary acts as a disincentive to grain boundary ionic conductivity. In addition, the maximum total equivalent conductivity at 1223K in this study reaches to 0.143 Scm-1 which can compare with that of certain YSZ. It will be beneficial to SOFCs application profited from increasing ionic conductivity of ceramic solid electrolytes.

The procedures for the extraction and separation of lipids and nutraceutics from microalgae using classic solvents have been used many times. However, these production methods usually require expensive and toxic solvents. Based on our studies involving the use of eco-sustainable methodologies and alternative solvents, we select ethanol (EtOH) and cyclopentyl methyl ether (CPME) for extracting bio-oil and lipids from algae. Different percentage of EtOH in CPME favors the production of an oil rich of SFA useful to production biofuel or rich of compounds bioactive. The proposed method for obtain a rich extract of saturated or unsaturated fatty acids from dry algal biomass is disclosed is eco-friendly and allows a good extraction yield. The method is compared both in extracted oil percentage yield and in extracted fatty acids selectivity to extraction by supercritical carbon dioxide.

Cancer is the most feared disease, with more than 1.6 million cases each year. Cancer can start almost anywhere in the human body, from the uncontrollable growth and multiplication of damaged cells. Cancerous tumors can spread into the human body (a process called metastasis) as a solid form usually, but the cancers of blood generally do not. Cancer treatment includes chemotherapy, surgery and radiations. In this article we will address inorganic compounds as a source of treatment, diagnosis, carriers of active substances.

The current study aims to fermentation parameter for producing microbial products. Microwave parameters consist on 245 MHz, and 600-watt for 60 seconds. Ethyl acetate was the best solvent used for extraction purposes. Antioxidant properties were differentiated by blocking the oxidation of the linoleic acid with an inhibition rate of 73.13% at a concentration of 200 mg/mL, in addition to increasing its effectiveness for free radical extraction and reduction strength by increasing concentrations gradually. The bond ability to irons was lower compared to the EDTA-2Na, in addition to the obtained total content corresponding to phenolic compounds in the ethyl acetate extract of fermented rice (Koji) by A. flavus was 232.11 mg, on the basis of galic acid/mg. The stability of the antioxidant compounds of the ethyl acetate extract of fermented rice (Koji) by A. flavus was also studied; showing stability under neutral conditions, as well as at high temperatures (185 °C during two hours). However, no stability was obtained under acidic and alkaline conditions.

Methodologies for the synthesis and purification of metabolites, which have been developed following their discovery, analysis and structural identification, have been involved in numerous life science milestones. The renewed focus on the small molecule domain of biological cells has also created an increasing awareness of the rising gap between the metabolites identified and the metabolites which have been prepared as pure compounds. Due to the large number and molecular diversity of metabolites the design and engineering of resource-efficient and straightforward synthetic methodologies for their production have attracted much interest. The variety of metabolic pathways in biological cells provide a wonderful blueprint for designing simplified and resource-efficient synthetic routes to desired metabolites. Therefore, biocatalytic systems have become key enabling tools for the synthesis of an increasing number of metabolites, which can then be utilized as standards, enzyme substrates, inhibitors or products, or for the discovery of novel biological functions.

A new class of tetrasubstituted imidazole based compounds was synthesized using a multicomponent one-pot synthesis scheme through a cyclo condensation reaction of benzil, aromatic primary amines, aldehydes and ammonium acetate in glacial acetic acid. The synthesized compounds have been analyzed and characterized by melting point, color, conductivity method, CHN analysis, FT-IR, and UV-Visible. The reaction proceeding was examined by TLC after regular intervals of period. To test biological activity, the synthesized compounds have been examined against various bacterial strains. From the analysis of the antibacterial activity of these synthesized compounds demonstrated that all three imidazole compounds have considerable to significant activity against the strains, and compound K2 was found potent comparatively.

This paper describes the preparation and description of four new complexes [Bu₂Sn(AA)Cl] (AA = glycine, DL-valine and L-leucine) and [Bu₂SnPhen₂] (Phen = DL-phenylalanine) They were characterized by elemental analyses of carbon, hydrogen, nitrogen, chlorine and tin; and by infrared, ^119mSn-Mössbauer and ^119mSn-RMN spectroscopies, and by the applications of TG and DSC techniques in dynamic helium atmosphere. For the [Bu₂Sn(AA)Cl], trigonal bipyramidal tin species, AA were coordinated bidentatedly by the carboxylic oxygen and by the NH₂ group. The [Bu₂SnPhen₂)], with tin atoms in trans-octahedral sites, had the Phen-coordinated by both carboxylic oxygen atoms.

Biocompatibility of ceramic materials in CaO-P2O5 system was investigated using different methods, including in vitro and in vivo tests. Ceramics based on calcium pyrophosphate Ca2P2O7 were obtained by annealing cement-salt stone from highly concentrated hardening suspensions (HCHS). Cement-salt stone was prepared using powder mixtures of calcium citrate tetrahydrate Ca3(C6H5O7)2·4H2O and monocalcium phosphate monohydrate (MCPM) Ca(H2PO4)2·H2O. These salts were mixed with each other in such a way that calcium pyrophosphate and calcium polyphosphate were present in the final ceramic product in the following weight ratios: Ca(PO3)2/Ca2P2O7 = 0/100; 5/95; 10/90 and 20/80. Distilled water was added to a homogenized powder mixtures of Ca3(C6H5O7)2·4H2O and Ca(H2PO4)2·H2O by a water/solid ratio of 0,5 by weight. The obtained suspensions were shaped using silicon molds and left to dry in air for a week. The phase composition of the obtained samples of cement-salt stone was represented by brushite CaHPO4·2H2O, monetite CaHPO4, calcium citrate tetrahydrate Ca3(C6H5O7)2·4H2O and monocalcium phosphate monohydrate Ca(H2PO4)2·H2O. According to the XRD data, the phase composition of ceramic materials after annealing in the temperature range of 800-1000 0C was mainly represented by the β-Ca2P2O7 phase. In vivo tests shown that obtained ceramic materials can be recommended for regenerative treatments for bone defects.

Advanced ceramics are recognized as key enabling materials possessing combinations of properties not achievable in other material classes. They are characterized by very high thermal, chemical and mechanical resistance and also usually have a lower density than metals. These properties predestine ceramics for many different applications, especially space applications.In the aerospace sector aerospike nozzles promise performance and application advantages compared to classic bell nozzles but are also inherently more complex to manufacture due to their shape. AM methods drastically simplify or even enable the fabrication of those complex structures while minimising the number of individual parts. The applicability of ceramic AM (“CerAMfacturing”) on rocket engines and especially nozzles is consequently investigated in the frame of the “MACARONIS” project, a cooperation of the Institute of Aerospace Engineering at Technische Universität Dresden and the Fraunhofer Institute for Ceramic Technologies and Systems (IKTS) in Dresden. The goal is to develop novel large size aerospike thrust nozzles including areas of highest resolution and fineness. Finding a suitable AM process that enables the realisation of both aspects is extremely challenging. One possibility could be the hybridization of shaping methods, in that case CerAM VPP (ceramic additive manufacturing via vat photopolymerization) and CerAM FFF (ceramic additive manufacturing via fused filament fabrication) in combination with sinter joining. This contribution focuses on the high resolution CerAM VPP process, in particular the development, characterization and testing of a new photoreactive Al₂O₃ suspension validated by AM of novel aerospike nozzles.

The copper end paste used in multilayer ceramic capacitors sintered in nitrogen atmosphere will lead to carbon residue of organic vehicle, which will lead to the reduction of electrode conduc-tivity and high scrap rate. With an attempt to leave no residue in the sintering, the compatibility of solvents and thickeners should be improved because it has an important influence on the hi-erarchical volatilization and carbon residue of organic vehicles. In this work, the volatility of different solvents was compared and several solvents were mixed in a definite proportion to prepare an organic vehicle with polyacrylate resins. The hierarchical volatility and solubility parameters of mixed solvents were adjusted effectively by changing proportions of different components, the thermogravimetric curves of resins and organic vehicles were measured by thermogravimetric analyzer, the effect of solubility parameter on the dissolvability of resins in the solvent and the residual of organic vehicles were studied. Results showed that the hierar-chical volatilization of solvents can be obtained by mixing different solvents; the intrinsic vis-cosity of the organic vehicle is higher and the thermal decomposition residue of polyacrylate resins is lower when the solubility parameters of mixed solvents and polyacrylate resins are closer. The low residual sintering of organic vehicles can be achieved by using the mixed solvent with hierarchical volatility and approximate solubility parameters as resins.

In view of the diminishing contribution of natural products from plants to the discovery of new chemical structures, the aim of this study was to compile the articles from 2021 to 2022, assessing: (1) which classes of compounds these new structures belong to; (2) which plants and families these compounds belong to and (3) assessing the degree of novelty of the compound with an already known structure. The review was elaborate following the Preferred Reporting Items for System-atics Reviews and Meta-analyses (PRISMA) statement checklist for guide reporting of systematic reviews. A total of 464 articles were selected for the new compounds of natural origin survey. We included 117 complete articles in this review and reported approximately 109 new structures elucidated during the years 2021 and 2022. Many of the compounds showed small structural var-iations in relation to already known molecules. For some, however, this small modification was decisive for the biological activity reported, demonstrating the importance of descriptive phytochemical studies.

The oceans harbor a great diversity of organisms, and have been recognized as an important source of new compounds with nutritional and therapeutic potential. Among these compounds, carbohydrate-based compounds are of particular interest because they exhibit numerous biological functions associated with their chemical diversity. This gives rise to new substances for the development of bioactive products. Many are the known applications of substances with glycosidic domains obtained from marine species. This review covers the structural properties and the current findings on the antioxidant, anti-inflammatory, anticoagulant, antitumor and antimicrobial activities of medium and high molecular-weight carbohydrates or glycosylated compounds extracted from various marine organisms.

The objective of this research was to explore the impact of a gradual replacement of Ca2+ with Mn1+ on the crystal structure of CaHPO4·2H2O, which could be beneficial for producing Ca1−xMnxHPO4·nH2O compounds. In order to prepare the starting solutions required for this study, Ca(NO3) 2·4H2O, (NH4)·2HPO4, and MnNO3·4H2O were used at various molar concentrations. The findings reveal that Mn substitutes Ca partly at low Mn/Ca molar ratios, and Mn doping reduces the unit cell of CaHPO4·2H2O. The produced biphasic compound was composed of monoclinic CaHPO4·2H2O and triclinic/monoclinic nanostructured Mn3PO4O11 after a continuous increase in the Mn/Ca molar ratio to 1. When the Ca/Mn molar ratio is 1.5, a triphasic compound of monoclinic CaHPO4·2H2O, triclinic Mn3P4O11, and Orthorhombic MnHPO4·(H2O)3 phases is formed. The formation of the monophasic MnHPO4·(H2O)3 compound was achieved by increasing the Mn/Ca molar ratio above 4. By adjusting the Mn/Ca molar ratio in the initial solutions, it is possible to produce biomaterials with specific and bespoke characteristics in the future. The Mn/Ca ratio of the starting solution can be modified to produce Ca1-xMnxHPO4-nH2O phases with weight percent compositions, as established. For the first time, Ca1−xMnxHPO4·nH2O compounds were synthesized using novel methods in this manuscript.

Hen egg is a bioavailable and a palatable source of protein, fatty acids and vitamins. Egg being a bird embryo, it is adapted as an important part of a high quality carnivore and scavenger diet through evolution. The biological value of egg protein is near to 100 % with the ten essential amino acids, excluding taurine, required by cats and dogs. Functions of over 400 bioactive proteins are growingly recognized in targeting to support pet health. Egg shell membrane contains several of these biomolecules and has shown effect on joint and skin health, anti-inflammatory and antimi-crobial effect in adaptive immunity as well as in gastrointestinal disorders, such as metabolic diseases and obesity. The lipid composition of eggs is unique for an animal product with two-thirds of un-saturated fatty acids consisting of linoleic acid, arachidonic acid, eicosapentaenoic acid, and do-cosahexaenoic acid. Eggs are also a diverse source of vitamins providing both water and fat soluble vitamins, especially choline. The nutritional value of an egg assists in maintaining health and shows potential supporting the mobility, cognitive and gastrointestinal health as well as skin repair.

Bisphenol-A (BPA) represents an important co-monomer for obtaining polycarbonate, epoxy resins, flame retardants, in paint, and other chemicals products. Products containing BPA are widely used, and thus, we can find it in the environment: in the air, in the soil, in natural surface water and in sediments, underground water in landfills, and in wastewater. BPA disturbs human and animals’ health. This influences the enzymatic, androgenic, neurological, liver and reproductive systems at different stages of human life: like in fetal stage, children and adults’ stages. Taking these inconveniences into account, it is very important to remove BPA from water. Ultrasonic technology can be considered a verry sustainable and efficient method to remove BPA from water. The advantages of this method is easy to implement on existing water treatment and purification facilities, it does not produce residual compounds that produce sludge, the time required for degradation is of the order of 1-2 hours and the level of degradation is very high. In this work, we presented the studies on the efficiency of ultrasonics under air atmosphere on the degradation of BPA. The influence of the frequency and of some additional compounds such as carbon tetrachloride, FeSO4 7H2O (FS), and ethyl anthraquinone (EAC) was studied. Three different frequencies were used: 1146 KHz, 864 KHz, 580 KHz, at a power of 50 W. It was identified the efficiency of BPA degradation over a period of 60 minutes, with sampling every 15 minutes. Using the LC-MS/MS technique, the degradation compounds were identified that result from the application of ultrasound processes. Pathways of BPA degradation were also proposed.

Skin cancer is a condition characterized by the abnormal growth of skin cells, primarily caused by exposure to ultraviolet (UV) radiation from the sun or artificial sources like tanning beds. Different types of skin cancer include melanoma, basal cell carcinoma, and squamous cell carcinoma. Despite the advancements in targeted therapies, there is still a need for a safer, highly efficient approach to preventing and treating cutaneous malignancies. Spices have a rich history dating back thousands of years and are renowned for their ability to enhance the flavor, taste, and color of food. Derived from various plant parts like seeds, fruits, bark, roots, or flowers, spices are important culinary ingredients. However, their value extends beyond the culinary realm. Some spices contain bioactive compounds, including phenolic compounds, which are known for their significant biological effects. These compounds have attracted attention in scientific research due to their potential health benefits, including their possible role in disease prevention and treatment, such as cancer. This review focuses on examining the potential of spice-derived phenolic compounds as preventive or therapeutic agents for managing skin cancers. By compiling and analyzing the available knowledge, this review aims to provide insights that can guide future research in identifying new anticancer phytochemicals and uncovering additional mechanisms for combating skin cancer.

The magnetic properties of RCo3B2 compounds, with heavy rare earths, are investigated by using magnetic measurements and electronic structure calculations. The cobalt sublattice magnetizations are very small and antiparallel oriented to rare earths moments. Contributions of cobalt moments to the Curie constants were also shown. The cobalt magnetic behavior has been analyzed in spin fluctuations model. The presence of short-range order above the Curie temperatures in RCo3B2 compounds with R=Tb, Dy, and Ho has been attributed to reminiscent R5d-Co3d interactions.

A series of novel indole Schiff base derivatives (2a–2t) containing a 1,3,4-thiadiazole scaffold modified with a thioether group were synthesized, and their structures were confirmed using FT-IR, ¹H NMR, ¹³C NMR, andHR-MS. In addition, the antifungal activity of synthesized indole derivatives was investigated against Fusarium graminearum (F. graminearum), Fusarium oxysporum (F. oxysporum), Fusarium moniliforme (F. moniliforme), Curvularia lunata (C. lunata), and Phytophthora parasitica var. nicotiana (P. p. var. nicotianae) using the mycelium growth rate method. Among the synthesized indole derivatives, compound 2j showed the highest inhibition rates of 100%, 95.7%, 89%, and 76.5% at a concentration of 500 μg/mL against F. graminearum, F. oxysporum, F. moniliforme, and P. p. var. nicotianae, respectively. Similarly, compounds 2j and 2q exhibited higher inhibition rates of 81.9% and 83.7% at a concentration of 500 μg/mL against C. lunata. In addition, compound 2j has been recognized as a potential compound for further investigation in the field of fungicides.

Natural compounds have diverse structures and are present in different forms of life. Metabolites such as tannins, anthocyanins, and alkaloids, among others, serve as a defense mechanism in live organisms and are undoubtedly compounds of interest for the food, cosmetic and pharmaceutical industries. Plants, bacteria, and insects represent a source of biomolecules with diverse activities, poorly studied in many cases. To use these molecules for different applications, it is essential to know their structure, concentrations, and biological activity potential. In vitro techniques that evaluate the biological activity of the molecules of interest have been developed since the 1950s. Currently, different methodologies have emerged to overcome some of the limitations of these traditional techniques, mainly the reduction of time and costs. However, emerging technologies continue to appear due to the urgent need to expand the analysis capacity of a growing number of reported biomolecules and the lack of therapeutic options to treat various diseases. This review presents an updated summary of the conventional and current methods to evaluate natural compounds' biological activity, including a diagram that summarizes the minimum techniques essential for correctly assessing molecules with biological potential.

This study surveyed the variation in Perfluorinated Compounds (PFCs) concentration entering urban wastewater treatment plants and proposed an optimal PFCS treatment method. The PFCS concentration in influent was shown to be affected by the types of industries and operating rate. The concentration of PFCs in the wastewater treatment effluent was slightly lower than that of influent. Thus, PFCs were considered to have barely been removed by the existing biological treatments. The pilot test result showed that about 10% of PFCs were removed by coagulation and precipitation, and the ozone and chlorine test also showed that few PFCs were removed regardless of the amount of injection. The activated carbon adsorption test showed that the removal was significantly increased by the empty bed contact time, with about a 60% removal in five minutes and over a 90% removal in 15 minutes. Therefore it is determined that a more stable and higher PFCs removal would result from the continuous oxidation processes such as ozone and adsorption processes such as activated carbon rather than a single biological treatment.

We present the results of calculations of magnetic properties of 3 compounds from Laves phase C15 family: DyAl2, HoAl2 and ErAl2 performed with a new computation system called ATOMIC MATTERS MFA. We compare these findings with the recently published results for TbAl2, GdAl2 and SmAl2. The calculation methodology was based on the localized electron approach applied to describe the thermal evolution electronic structure of rare-earth R3+ ions over a wide temperature range and to compute magnetocaloric effect (MCE). Thermomagnetic properties were calculated based on the fine electronic structure of 4f9, 4f10 and 4f11 configurations of the Dy3+, Ho3+, Er3+ ions, respectively. Our calculations yield the magnetic moment value and direction; single-crystalline magnetization curves in zero field and external magnetic field applied in various directions of m(T, Bext); the 4f-electronic components of specific heat c4f(T, Bext); and temperature dependence of the magnetic entropy and isothermal entropy change with external magnetic field -S(T, Bext). The cubic CEF parameter values used for DyAl2 calculations are taken from earlier research of A.L. Lima, A.O. Tsokol and recalculated for universal cubic parameters (Amn) for the RAl2 series. Our studies reveal the importance of multipolar charge interactions when describing thermomagnetic properties of real 4f electronic systems and the effectiveness of an applied self-consistent molecular field in calculations for magnetic phase transition simulation.

Evidence regarding the effect of the onlay preparation design for different CAD/CAM restorative materials considering the preservation of cusps is lacking. Molars were 3D modeled in four preparation designs for onlay restoration: traditional design with functional cusp coverage (TFC), non-retentive design with functional cusp coverage (NFC), traditional design with non-functional cusp coverage (TNFC), non-retentive design with non-functional cusp coverage (NNFC). Restorations were simulated with two CAD/CAM restorative materials: LD – lithium disilicate (IPS e.max CAD) and RC - resin composite (GrandioBloc). A 100 N axial load was applied to the occlusal surface simulating the centric contact point. Von Mises (VM) and maximum principal (Pmax) stresses were evaluated for restorations, cement layer and dental substrate. The non-retentive preparation design reduced the stress concentration in the tooth structure in comparison to the conventional retentive design. For LD onlays, the stress distribution on the restoration intaglio surface showed that the preparation design as well as the prepared cusp, influenced the stress magnitude. The non-retentive preparation design provided better load distribution in both restorative materials and more advantageous for tooth structure. The resin composite restoration on non-functional cusp is recommended when functional cusp is preserved, in order to associate conservative dentistry and low stress magnitude.

Talking about sustainable development refers mainly to the environmental sphere, but the concept is much broader and also takes into account the social and economic conditions. The concept of sustainability, in this sense, is linked to the compatibility between the development of economic activities, the related social phenomena, and the protection of the environment. Therefore, the ability to balance social, economic and environmental sustainability is the very meaning of the concept of sustainable development. Firms that choose to develop policies and strategies to enhance and pursue sustainable development in the medium to long term have the burden of having to quantitatively document the improvements in production processes with the aim of sustainable development. As a result, one of the biggest challenges for European industry is to introduce sustainability principles into business models leading to competitive advantage. This is particularly important in raw material and energy intensive manufacturing sectors such as the ceramic industry. The present state of knowledge lacks a comprehensive operational tool for industry to support decision-making processes geared towards sustainability. In the ceramic sector, the economic and social dimensions of the product and processes have not yet been given sufficient importance. Moreover, the traditional research on industrial districts lacks an analysis of the relations between firms and the territory with a view to sustainability. Finally, the attention of scholars in the field of economic and social sustainability, has not yet turned to the analysis of the Sassuolo district. Therefore, in this paper we introduce the Life Cycle Sustainability Assessment (LCSA), as a method that can be a suitable tool to fill this gap, because through a mathematical model it is possible to obtain the information useful for decision makers to integrate the principles of sustainability both at the microeconomic level in enterprises, and at the meso-economic level for the definition of economic policies and territorial governance. Environmental and socio-economic analysis was performed from the extraction of raw materials to the packaging of the product on different product categories manufactured by the Italian ceramic industries of the Sassuolo district (northern Italy). For the first time the LCSA model, usually applied to unitary processes, is extended to the economic and industrial activities of the entire district, extending the prospect of investigation from the enterprise and its value chain to the integrated network of district enterprises.

Fosmidomycin (FOS) is a naturally occurring compound active against the enzyme DXR in the MEP pathway, and using it as a template for lead structure design is an effective strategy in developing new active compounds. In this work, by replacing the hydroxamate unit of FOS with pyrazole, isoxazole and the related heterocycles that also have the metal ion binding affinity, while retaining the monophosphonic acid in FOS or replacing it with a bisphosphonic acid group, heterocycle-containing mono- and bisphosphonic acid compounds as FOS analogs were designed. The key steps involved in the facile synthesis of these FOS analogs include the Michael addition of diethyl vinylphosphonate or tetraethyl vinylidenebisphosphonate to β-dicarbonyl compounds and the subsequent cyclic condensation with hydrazine or hydroxylamine. Two additional isoxazolinone-bearing FOS analogs were synthesized by the Michaelis-Becker reaction with diethyl phosphite as a key step. The bioactivity evaluation on model plants demonstrated that several compounds have better herbicidal activities compared to FOS, with the most active compound showing a 3.7-fold inhibitory activity on Arabidopsis thaliana, while on the root and stalk of Brassica napus L. and Echinochloa crus-galli in pre-emergence inhibitory activity test, the activities of this compound were found to be 3.2- and 14.3-, 5.4- and 9.4-fold, respectively, and in post-emergency activity test on Amaranthus retroflexus and Echinochloa crus-galli, 2.2- and 2.0-fold inhibition activities were displayed. Despite the significant herbicidal activity, this compound exhibited a DXR inhibitory activity lower than that of FOS but comparable to that of other non-hydroxamate DXR inhibitors, and the dimethylallyl pyrophosphate rescue assay gave no statistical significance, suggesting a different target might be involved in the inhibiting process. This work demonstrates that using bioisosteric replacement can be considered a valuable strategy for discovering new FOS analogs that may have high herbicidal activity.

Sulfur, peroxide and combined sulfur and peroxide curing systems were applied for cross-linking of unfilled and carbon black filled rubber compounds based on ethylene-propylene-diene-monomer rubber. The results revealed that the type of curing system influenced the course and shape of curing isotherms. This resulted in the change of curing kinetics of rubber compounds. The cross-link density of vulcanizates cured with combined vulcanization systems was lower than that for vulcanizates cured only in the presence of sulfur or peroxide system. The results revealed good correlation between the cross-link density as well as the structure of the formed cross-links and physical-mechanical characteristics of the materials. It can be stated that by proper combination of vulcanization systems it is possible to modify tensile behavior of vulcanizates in targeted manner. On the other side, dynamical-mechanical properties were found not be significantly influenced by the composition of curing system.

In recent years, the FDA has approved numerous antitumor drugs that are mutation-based for clinical use. These drugs have improved the precision of treatment and reduced adverse effects and side effects. Personalized therapy is a prominent and hot topic of current medicine and also represents the future direction of development. With the continuous advancements in gene sequencing and high-throughput screening, research and development strategies for personalized clinical drugs have developed rapidly. This review elaborated the recent personalized treatment strategies, which include artificial intelligence, multi-omics analysis, chemical proteomics, and computation aided drug design. These technologies rely on the molecular classification of diseases, the global signaling network within organisms, and new models for all targets, which significantly support the development of personalized medicine. Meanwhile, we summarized chemical drugs such as lorlatinib, osimertinib, and other natural products that deliver personalized therapeutic effects based on genetic mutations. This review also highlights potential challenges in interpreting genetic mutations and combining drugs, while providing new ideas for the development of personalized medicine and pharmacogenomics in cancer study.

The vulcanization of rubber compounds is an exothermal process. A carbon black-filled and natural rubber-based (NR) formulation was mixed with different levels of sulfur (0.5, 1.0, 2.0, 4.0 and 6.0 phr) and studied with Differential Scanning Calorimetry (DSC) for the determination of the vulcanization enthalpy. It was found that the vulcanization enthalpy is dependent from the amount of sulfur present in the compound and the vulcanization heat released was -18.4 kJ/mol S if referred to the entire rubber compound formulation or -46.0 kJ/mol S if the heat released is referred only to the NR present in the compound. The activation energy for the vulcanization of the rubber compounds was also determined by a DSC study at 49 kJ/mol and found quite independent from the sulfur content of the compounds under study. A simplified thermochemical model is proposed to explain the main reactions occurring during the vulcanization. The model correctly predicts that the vulcanization is an exothermal process although it gives an overestimation of the vulcanization enthalpy which is larger for the EV vulcanization package and smaller for the conventional vulcanization system. If the devulcanization is conducted mechanochemically in order to break selectively the sulfur-based crosslinks, then the natural rubber compounds recovered from used tires can be re-vulcanized again and the exothermicity of such process can be measured satisfactorily with DSC analysis. This paper not only proposes a simplified mechanism of vulcanization and devulcanization but also proposes an analytical method to check the devulcanization status of the recycled rubber compound in order to distinguish truly devulcanized rubber from reclaimed rubber.