The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

This paper is devoted to change-point detection using only the ordinal structure of a time series. A statistic based on the conditional entropy of ordinal patterns characterizing the local up and down in a time series is introduced and investigated. The statistic requires only minimal a priori information on given data and shows good performance in numerical experiments.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

This paper studies single change-point detection in the volatility of a class of parametric conditional heteroscedastic autoregressive nonlinear (CHARN) models. The conditional least-squares (CLS) estimators of the parameters are defined and are proved to be consistent. A Kolmogorov-Smirnov type-test for change-point detection is constructed and its null distribution is provided. An estimator of the change-point location is defined. Its consistency and its limiting distribution are studied in detail. A simulation experiment is carried out to assess the performance of the results which are also applied to two sets of real data.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

This study considers the change-point test problem for time series based on the self-normalization ratio statistic test, which is constructed using residuals obtained from a support vector regression (SVR)-autoregressive moving average (ARMA) model. Under the null hypothesis, the series is a stationary process, and our test statistic converges to a non-degenerate distribution. Under the alternative hypothesis, there are change-points in the time series, and the self-normalization test statistic diverges to infinity. The simulations show that our proposed new test has better finite sample performance than other SVR-based tests in the literature. Finally, we illustrate its usefulness by analyzing two actual data sets.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

Most petrochemical plants still maintain a Proportional-Integral-Differential controller(PID) system, which is a feedback control system. However, gradually, the PID system is being extended and introduced to the Advanced Process Controller (APC) system, which is an integrated control system of feedforward and feedback that predicts external influences in advance. In the process of conducting on-site plant tests and calculating APC model parameter for the application of APC systems, a problem arises that Model Parameter are implemented differently depending on the proficiency of APC engineers. To minimize this problem, a technique for estimating APC model parameter without a plant test is required. In order to estimate the APC model parameter, it is necessary to train on dynamic interval data. In this paper, we use statistical techniques such as PELT, Linear Kernel, and Radial Basis Function Kernel of Change Point Detection (CPD) to extract dynamic data with minimum Mean Absolute Error (MAE) from time series data of a real petrochemical plant. Then, the hyper parameter is fixed and the APC model parameter is estimated by learning the dynamic section data. By applying the estimated APC model parameter to the APC Model Tool and measuring the fitting rate, it was confirmed that it is possible to estimate the APC model parameter with excellent control performance without plant test.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

3D object detection is essential for an accurate and reliable autonomous driving system. Currently, the methods used by the state-of-the-art two-stage detectors are not flexible enough and their fea-ture extraction capabilities are very limited to cope effectively with the disorder and irregularity of point clouds. In this paper, we combine the advantages of both PV-RCNN and PAConv (Position Adaptive Convolution) to create a completely new network, FANet, in order to overcome the ir-regularity and disorder of point clouds. The convolution in our network builds convolutional ker-nels from a basic weight matrix, whose combined coefficients are learned adaptively by LearnNet from relative points. This network allows for flexible modeling of complex spatial variations and geometric structures in the 3D point cloud, enabling better extraction of point cloud features and producing high-quality 3D proposal boxes. Compared to other methods, FANet is superior in terms of 3D object detection accuracy. Extensive experiments on the KITTI dataset have shown a signif-icant improvement in our approach.

Change Detection (CD) of aerial images refers to identifying and analyzing changes between two or more aerial images of the same location taken at different times. The CD is a highly challenging task due to the need to distinguish relevant changes, such as urban expansion, deforestation, or post-disaster damage assessment, from irrelevant ones, such as light conditions, shadows, and seasonal variations. Many CD papers have recently been published, where most of the papers that proposed a new model contained a comparison between their proposed and state-of-the-art (SOTA) models. While many recent studies propose new deep learning (DL) models for improving CD performance, their comparative analyses are often restricted, lacking comprehensive insights into the proposed models' real-world generalizability, robustness, and performance trade-offs across diverse change characteristics. This paper presents a novel generic framework to systematically benchmark and assess DL-based CD models through three parallel pipelines: 1) cross-testing models on diverse benchmark datasets to evaluate generalization, 2) robustness analysis against different image corruptions, and 3) multi-faceted contour-level analytics evaluating detection sensitivity to change size/complexity. The framework is applied to comparatively evaluate five state-of-the-art DL-based CD models - Changeformer, BIT, Tiny, SNUNet, and CSA-CDGAN. Extensive experiments unveil each model's strengths, limitations and biases, highlighting their relative proficiencies in generalizing across data distributions, resilience to noise corruption, and discriminative capabilities for changes of varying characteristics. The proposed benchmarking framework demonstrates significant potential for guiding the selection of suitable CD models tailored to specific application requirements by comprehensively evaluating their generalizability, robustness, and detection capabilities across diverse real-world scenarios. This systematic evaluation approach can drive future research into developing more robust and versatile CD solutions aligned with practical needs.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

In the realm of autonomous vehicle environment perception, the primary objective of point cloud target detection is to swiftly and accurately identify three-dimensional objects from point cloud data. To meet this requirement, the prevalent network architecture employed in the industry is the voxel-based PointPillars model. Nonetheless, this model faces challenges in maintaining detection accuracy when objects are obscured or diminutive in size. In response to this issue, we introduce AGPNet, a novel model that seamlessly integrates four key modules: Data Augmentation, Dynamic Graph CNN, Pillar Feature Net, and Detection Head (SSD). The Data Augmentation module enhances the adaptability of point cloud data to complex and ever-changing real-world environments. The Dynamic Graph CNN module endows the network structure with geometric features, which encapsulate not only the point itself but also its adjacent points. The Pillar Feature Net module translates three-dimensional point cloud data into pseudo-image data through the utilization of voxels. Subsequently, the Detection Head (SSD) module leverages this pseudo-image data to conduct target detection of three-dimensional objects. Our experiments, conducted on the KITTI dataset, demonstrate that our proposed method boosts object detection accuracy by 6-7 percentage points compared to the PointPillars model, while maintaining similar detection times.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

Biosensors have shown great potential in realizing rapid, low cost and portable on-site detection for diseases. This work reports the development of a new bioelectronic sensor called AC electrokinetics-based capacitive (ABC) biosensor, for the detection of genomic DNA (gDNA) of methicillin-resistant Staphylococcus aureus (MRSA). The ABC sensor is based on interdigitated microelectrodes biofunctionalized with oligonucleotide probes. It uses a special AC signal for direct capacitive monitoring of topological change on nanostructured sensor surface, which simultaneously induce dieletrophoretic enrichment of target gDNAs. As a result, rapid and specific detection of gDNA/probe hybridization can be realized with high sensitivity. It requires no signal amplification such as labelling, hybridization chain reaction, or nucleic acid sequence-based amplification. This method involves only simple sample preparation. After optimization of nano-structured sensor surface and signal processing, the ABC sensor demonstrated fast turnaround of results (~10 s detection), excellent sensitivity (a detection limit of 4.7 DNA copies /µL MRSA gDNA) and high specificity, suitable for point of care diagnosis. As a bioelectronic sensor, the developed ABC sensors can be easily adapted for detection of other infectious agents.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

This paper aims at tackling with the task of fusion feature from images and its corresponding point clouds for 3D object detection in autonomous driving scenarios basing on AVOD, an Aggregate View Object Detection network. The proposed fusion algorithms fuse features targeted from Bird’s Eye View (BEV) LIDAR point clouds and its corresponding RGB images. Differs in existing fusion methods, which are simply the adoptions of concatenation module, element-wise sum module or element-wise mean module, our proposed fusion algorithms enhance the interaction between BEV feature maps and its corresponding images feature maps by designing a novel structure, where single level feature maps and another utilizes multilevel feature maps. Experiments show that our proposed fusion algorithm produces better results on 3D mAP and AHS with less speed loss comparing to existing fusion method used on the KITTI 3D object detection benchmark.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p < 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p < 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

This paper presents a novel segmentation algorithm specially developed for applications in 3D point clouds with high variability and noise, particularly suitable for heritage building 3D data. The method can be categorized within the segmentation procedures based on edge detection. In addition, it uses a graph-based topo-logical structure generated from the supervoxelization of the 3D point clouds, which is used to make the clo-sure of the edge points and to define the different segments. The algorithm provides a valuable tool for generating results that can be used in subsequent classification tasks and broader computer applications dealing with 3D point clouds. One of the characteristics of this segmentation method is that it is unsupervised, which makes it particularly advantageous for heritage applications where labelled data is scarce. It is also easily adaptable to different edge point detection and supervoxelization algorithms. Finally, the results show that the 3D data can be segmented into different architectural elements, which is important for further classification or recognition. Extensive testing on real data from historic buildings demonstrates the effectiveness of the method. The results show superior performance compared to three other segmentation methods, both globally and in the segmentation of planar and curved zones of historic buildings.

The prevalence of hepatitis B and delta viruses (HBV/HDV) among people who use drugs (PWUD) remains largely unknown. In the context of one Philadelphia-based harm reduction organization (HRO), this study aimed to assess HBV/HDV prevalence and facilitate linkage to care. Participants completed a demographic HBV/HDV risk factor survey and were screened for HBV and reflexively for HDV if positive for HBV surface antigen or isolated core antibody. Fisher’s exact tests and regression were used to understand relationships between risks and HBV blood markers. Of the 498 participants, 126 (25.3%) were susceptible to HBV, 52.6% had been vaccinated against HBV, and 17.9% had recovered from a past infection. Eleven (2.2%) participants tested positive for isolated HBV core antibody, 10 (2.0%) for HBV surface antigen, and one (0.2%) for HDV antibody. History of incarceration was associated with current HBV infection, while transactional sex and experience of homelessness were predictive of previous exposure. This study found high rates of current and past HBV infection, and a 10% HBV/HDV co-infection rate. Despite availability of vaccine, one quarter of participants remained vulnerable to infection. Findings demonstrate the need to improve low-threshold HBV/HDV screening, vaccination, and linkage to care among PWUD. The study also identified gaps in the HBV/HDV care cascade, including lack of point-of-care diagnostics and lack of support for HROs to provide HBV services.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

Traditional applications of Interferometric Synthetic Aperture Radar (InSAR) data involved inverting an interferogram stack to determine the average displacement velocity. While this approach has useful applications in continuously deforming regions, much information is lost by simply fitting a line through the time series. Thanks to regular acquisitions across most of the the world by the ESA Sentinel-1 satellite constellation, we are now in a position to explore opportunities for near-real time deformation monitoring. In this paper we present a simple statistical approach for detecting offsets and gradient changes in InSAR time series. Our key assumption is that 5 years of Sentinel-1 data is sufficient to calculate the population standard deviation of the detection variables. Our offset detector identifies statistically significant peaks in the first, second and third difference series. The gradient change detector identifies statistically significant movements in the second derivative series. We exploit the high spatial resolution of Sentinel-1 data and the spatial continuity of geophysical deformation signals to filter out false positive detections that arise due to signal noise. When combined with near-real time processing of InSAR data these detectors, particularly the gradient change, could be used to detect incipient ground deformation associated with geophysical phenomena, for example from landslides or volcanic eruptions.

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

Land use and land cover (LULC) datasets for Jinan in 1992, 1998, 2002, 2006, 2011, 2017, and 2022 were developed from Landsat images using the Random Forest (RF) classification approach. The relationships between social-economic, political factors and time-series LULC data were exam-ined for the periods between 1992 and 2022. The results showed the effectiveness of using the RF classification method for LULC classification with time series of Landsat images. Combined with driving forces analysis, our research can effectively explain the detailed LULC change tra-jectories corresponding to different stages and give new insights into Jinan LULC change pat-terns. The results show a significant increase in impervious surface which opposite change to bare land which experienced a huge decline declined by 95%, due to urbanization and rapid in-crease of population. The driving forces behind these changes are related to population growth, economic development, and climate change. Moreover, the present research employed Principal Components Analysis (PCA) methodology in order to understand the relative significance of disparate driving factors. The analysis results prove that the economy (population, GDP) and climate change were the primary factors that have an obvious impact on land use/land cover changes and that the driving factors for impervious surface, bare land, woodland, farmland, and water were distinct. Government policies also have a substantial impact on LULC change as well, such as the Construction of Harmonious Jinan (COHJ). The results were helpful for better understanding the mechanisms of LULC change and can provide useful knowledge for effective land resource management and planning.

Identifying macroeconomic events that are responsible for dramatic changes of economy is of particular relevance to understand the overall economic dynamics. We introduce an open-source available efficient Python implementation of a Bayesian multi-trend change point analysis which solves significant memory and computing time limitations to extract crisis information from a correlation metric. Therefore, we focus on the recently investigated S&P500 mean market correlation in a period of roughly 20 years that includes the dot-com bubble, the global financial crisis and the Euro crisis. The analysis is performed two-fold: first, in retrospect on the whole dataset and second, in an on-line adaptive manner in pre-crisis segments. The on-line sensitivity horizon is roughly determined to be 80 up to 100 trading days after a crisis onset. A detailed comparison to global economic events supports the interpretation of the mean market correlation as an informative macroeconomic measure by a rather good agreement of change point distributions and major crisis events. Furthermore, the results hint to the importance of the U.S. housing bubble as trigger of the global financial crisis, provide new evidence for the general reasoning of locally (meta)stable economic states and could work as a comparative impact rating of specific economic events.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

The goal of this study was to develop a rapid diagnostic kit for rheumatic disease and systemic lupus erythematosus (SLE) screening. A novel rapid vertical flow assay (VFA) was engineered and used to assay anti-nuclear (ANA) and anti-dsDNA (αDNA) autoantibodies from systemic lupus erythematosus (SLE) patients and healthy controls (HC). Observer scores and absolute signal intensities from the VFA were validated by ELISA. The rapid ten minute point of care VFA test engineered demonstrated a limit of detection of 0.5 IU/ml for ANA and αDNA autoantibodies in human plasma with inter-operator CV of 19% for ANA and 12% for αDNA. Storage stability was verified over a three-month period. When testing anti-dsDNA and ANA levels in 22 SLE and 18 HC serum samples, the duplex VFA revealed 95% sensitivity, 72% specificity and 84% accuracy in discriminating disease groups, comparable to the gold standard, ELISA. The rapid αDNA/ANA duplex VFA can potentially be used in primary care clinics for evaluating patients or at-risk subjects for rheumatic diseases and for planning follow-up testing. Given its low cost, ease and rapid turnaround, it can also be used to assess SLE prevalence estimates.

Daily rainfall data was collected for the arid district of Ananthapuramu, Andhra Pradesh state, India from 1981 to 2016 at the sub-district level and aggregated to monthly, annual and seasonal rainfall totals and the number of rainy days. The objective of this study is to evaluate the homogeneity, trend, and trend change points in the rainfall data. After quality checks and homogeneity analysis, a total of 27 rain gauge locations were considered for trend analysis. A serial correlation test was applied to all the time series to identify serially independent series. Non-Parametric Mann-Kendall test and Spearman’s rank correlation tests were applied to serially independent series. The magnitude of the trend was calculated using Sen’s slope method. For the data influenced by serial correlation, various modified versions of Mann-Kendall tests (Pre-Whitening, Trend Free Pre-Whitening, Bias Corrected Pre-Whitening and two variants of Variance Correction Approaches) were applied. A significant increasing summer rainfall trend is observed in 6 out of 27 stations. Significant decreasing trends are observed at two stations in the south-west monsoon season and at two stations in the north-east monsoon season. To identify the trend change-points in the time series, distribution-free Cumulative SUM test and sequential Mann-Kendall tests were applied. Two open-source library packages were developed in R language namely, ‘modifiedmk’ and ‘trendchange’ to implement the statistical tests mentioned in this paper. The study will benefit water resource management, drought mitigation, socio-economic development and sustainable agricultural planning in the region.

Subnational governments play a key role responding to climate change risks in terms of policy strategies and instruments. This article analyzes how Brazilian municipal and state governments have developed and implemented public policies to mitigate and to adapt to climate change risks. We surveyed all cities’ and states’ climate policies within the country. The methodological approach includes five main points of analysis: 1. mitigation targets and intentions; 2. adaptation actions; 3. stakeholders’ participation; 4. policy implementation; 5. participation in networks related to climate change. Our results suggest that even though subnational climate policies in Brazil are isolated initiatives within the national context, they play an important role responding to climate change risks in different scales and levels. The strongest Brazilian policies with both mitigation and adaptation actions counted on previous mobilization for the climate issue involving different stakeholders from several segments of the society. These governments have also participated in transnational cooperation networks related to climate change.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

Poultry farming in Slovakia has a tradition and an irreplaceable position to ensure rational nutrition for the population. In terms of a nutritional value, poultrymeat (Galliformes) contains a high amount of proteins, essential amino acids, essential unsaturated fatty acids, minerals, vitamins and a low fat content. Poultrymeat production has a relatively short reproductive cycle and thus allows regulating the demand and supply. The poultry market also influences the development of domestic consumption. According to the Statistical Office of the Slovak Republic, the consumption of meat has witnessed a persistent increase over the last 10 years. [1] According to the 2023 AVEC (The Voice of European Meat Sector) annual report, the consumption of poultrymeat in Slovakia was 20.0 kg per person per year. The average consumption in the EU-27 (2021) was 23.4 kg, with the countries with the highest consumption being Portugal (37.8 kg), Ireland (36.0 kg), Hungary (33.5 kg) and Spain (29.9 kg). On the other hand, the countries with the lowest consumption of poultrymeat, apart from Slovakia, also include Austria and Greece with a consumption of 21.5, resp. 21.0 kg [2]. The breeding of broiler chickens, as well as the production and placing on the market of poultrymeat must comply with the requirements laid down by legislation, while the compliance is regularly checked by the competent authorities.

All types of sports are potential application scenarios for automatic and real-time visual object and event detection. In rink hockey, the popular roller quad skate variant of hockey team sports, it is of great interest to automatically track player’s movements and positions, player’s sticks and, also, making other judgments, such as being able to locate the ball. In this work, we introduce a real-time pipeline composed by an object detection model, created specifically for rink hockey games, followed by a knowledge-based event detection module. Even in the presence of occlusions and quick motions, our deep learning object detection model effectively identifies and tracks, in real-time, important visual elements such as: ball; players; sticks; referees; crowd; goalkeeper; and goal. Using a curated dataset composed by a collection of videos of rink hockey, comprising 2525 annotated frames, we trained and evaluated the algorithm performance and compare it to state of the art object detection techniques. Our object detection model, based on YOLOv7, presents a global accuracy of 80%, and presents a good performance in terms of accuracy and speed, according to our results, making it a good choice for rink hockey applications. In our initial tests, the event detection module successfully detected one important event type in rink hockey games, the occurrence of penalties.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

The changing of land use and land cover (LULC) are both affected by climate and human activity and affect climate, biological diversity, and human well-being. Accurate and timely information about the LULC pattern and change is crucial for land management decision-making, ecosystem monitoring, and urban planning, especially in developing economies undergoing industrialization, urbanization, and globalization. Biodiversity degradation and urban expansion in eastern China are research hot-spots. However, the influence of LULC changes on the region remains largely unexplored. Here, an object-based and multi-temporal image analysis approach was developed to detect how LULC changes during 1985-2015 in the Tiaoxi watershed (Zhejiang province, eastern China) using Landsat TM and OLI data. The main objective of this study is to improve the accuracy of unsupervised change detection from object-based and multi-temporal images. To this end, a total of seven LULC maps are generated with multi-temporal images. A random stratified sample design was used for assessing change detection accuracy. The proposed method achieved an overall accuracy of 91.86%, 92.14%, 92.00%, and 93.86% for 2000, 2005, 2010, and 2015, respectively. Nevertheless, the proposed method, in conjunction with object-oriented and multi-temporal satellite images, offers a robust and flexible approach to LULC changes mapping that helps with emergency response and government management. Urbanization and agriculture efficiency are the main reasons for LULC changes in the region. We anticipate that this freely available data will improve the modeling for surface forcing, provide evidence of changes in LULC, and inform water-management decision-making.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Conventional method for monitoring the IgG levels suffered from some apparent problems such as long assay time, multistep processing, and high overall cost. An effective and suitable optical platform for label-free biosensing has been investigated by the implementation of antibody/antigen immunoassays. Thus, the ultrasensitive detection of IgG levels can be achieved by exploiting the dispersion turning point (DTP) existed in the tapered two-mode fibers (TTMFs) due to the sensitivity will reach ±∞ on either side of the DTP. Tracking the resonant wavelength shift it was found that the fabricated TTMF device exhibited limits of detection (LOD) down up to concentrations of 10 fg/mL of IgG in PBS solution. Such immunosensors based on the DTP have great significance on trace detection of IgG due to simple detection scheme, quick response time, and miniaturation.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Species distribution models have become tools of great importance in ecology since the advanced knowledge of suitable habitat of species is needed in the process of the world's biodiversity conservation. Models that use presence-only data are of great interests and are widely used in ecology due to their easy access. However, these models do not estimate accurately the true spatial species distribution based solely on presence-only data since they do not account for biases induced by the sampling techniques used and imperfect detection. To address this gap, Hierarchical integrated models have been recently introduced. Through this study, we assessed the relative performance of these new SDMs models using simulated data. The performance of the models was tested by comparing the estimates of parameters of the distribution models they provide with parameters used to simulate the distribution of the virtual species. The best model was the one whose estimates were close to the true distribution parameters of the virtual species. Results showed that analyzing Presence-only data in conjunction with Point-counts data through the Dorazio's Hierarchical model produced estimates of the coecients of the species intensity models with high precision and less bias while the Koshkina integrated model showed poor performance. Site-occupancy data, being not informative of species abundance, did not allow reducing biases in Presence-only data. The Dorazio's Hierarchical model produced estimates with high precision even with low detection probability. We have also found that the species rarity tends to in ate the variability of the models' estimates making modelling abundant species to be more accurate than modelling less abundant species. Hence, to model the species distribution with high precision based on Presence-only data, additional Point-counts data are required to account for sampling bias and imperfect detection.

This study investigates the impacts of climate change policies on businesses across various sectors, aiming to understand how these regulations affect operational, financial, and strategic aspects of business management. Utilizing a mixed-methods approach, data was collected from 500 businesses through surveys and interviews, encompassing a wide range of industries, sizes, and geographic locations. The findings reveal a complex landscape where 30% of businesses report positive impacts, primarily in the renewable energy and technology sectors, citing increased demand for green products and improvements in energy efficiency. Conversely, 45% of businesses, especially from manufacturing and agriculture, experience negative impacts, including increased operational costs and regulatory compliance challenges. Notwithstanding, a significant majority of businesses are committed to enhancing their sustainability practices, viewing climate change policies as an opportunity for innovation and long-term growth. The study highlights the nuanced effects of climate change policies, emphasizing the need for sector-specific support measures to alleviate financial and operational burdens on negatively impacted businesses. Moreover, it points to a broader shift towards sustainability within the business community, suggesting that climate policies, despite their varied impacts, are driving significant changes in business strategies towards environmental stewardship.

ABSTRACT Purpose: Tongue image analysis for disease diagnosis is an ancient traditional non-invasive diagnosis technique widely used by traditional medicine practitioners. Deep Learning based multi-label disease detection models offer tremendous potential to clinical decision support systems, by facilitating preliminary diagnosis. Methods: In this work, we propose a multi-label disease detection pipeline, where in observation and analysis of tongue images captured and received via smartphones assist in predicting the health status of an individual. All images are voluntarily given by subjects consulting collaborating physicians. Images thus acquired are first and foremost classified either into a diseased or a normal category by a 5-fold cross-validation algorithm using a convolution neural network (MobileNetV2) model for binary classification. Once the diseased label is predicted, the image is used to diagnose multiple diseases using the prediction algorithm based on DenseNet121. Results: Average accuracy of 93 % was achieved in classifying diseased from normal healthy tongue by detection model with MobileNetV2 architecture. Multilabel disease classification produced more than 90% accurate results for the seven class labels considered. Conclusion: AI based image analysis shows promising results and an extensive dataset could provide further improvements to this approach. Rather than employing high-cost sophisticated image capturing setup, experimenting with smartphone images opens opportunity to provide preliminary health status to individuals on smartphone prior to further line of treatment and diagnosis.

Human activities and natural events alter the earth’s surface and pose a constant threat to the environment. Thus, accurately monitoring and predicting these changes in a timely manner is crucial to provide solutions and mitigate the environmental consequences beforehand. This research introduces a novel framework, called HCD-Net, for change detection using bi-temporal hyperspectral images. The framework is based on double-stream deep feature extraction and an attention mechanism. The first stream focuses on deep feature extraction through 3D convolution layers and 3D Squeeze-and-Excitation (SE) blocks. The second stream focuses on deep feature extraction through 2D convolution and 2D SE blocks. The extracted deep features are then concatenated and fed to dense layers for decision-making. The efficiency of HCD-Net is compared to the state-of-the-art change detection methods. Additionally, the bi-temporal Airborne Visible InfraRed Imaging Spectrometer (AVIRIS) hyperspectral dataset was used for further evaluation of the change detection results. The results show that HCD-Net has a higher accuracy and the lowest false alarm rate, where the overall classification accuracy is above 96%, and the kappa coefficient is over 0.9.

Artificial intelligence (AI) has emerged as a powerful tool for addressing the challenges posed by climate change and their impact on public health. By leveraging its capacity to analyze and predict climatic patterns, AI offers opportunities to enhance resource management and develop effective strategies for climate change mitigation. Moreover, AI can contribute to generating sustainable solutions that address the complex and interconnected nature of climate change. For example, AI can enable the optimization of energy consumption and facilitate the integration of renewable energy sources into existing systems. It can also support the development of climate models that provide timely and accurate predictions, enabling policymakers to implement proactive measures for disaster preparedness and response. Furthermore, AI-powered disease surveillance and mitigation techniques can improve public health outcomes by identifying patterns and trends in the spread of diseases in relation to climatic factors.However, the widespread adoption of AI-based solutions is not without challenges. Ethical concerns surrounding privacy and data ownership must be addressed, as the use of AI requires access to large datasets, raising potential privacy risks. Technical constraints, such as limited computational power and the need for sophisticated algorithms, also pose obstacles to the implementation of AI in climate change mitigation strategies. Furthermore, issues related to the accessibility and affordability of AI technologies must be resolved to ensure equitable distribution and maximize its potential impact on public health.To fully harness the power of AI in addressing climate change and improving public health outcomes, it is crucial to promote innovation, multidisciplinary collaboration, and open data science. Innovation can drive the development of new AI algorithms and technologies specifically tailored to address climate change challenges. Multidisciplinary approaches that bring together experts from diverse fields, including climate science, public health, and computer science, can foster a holistic understanding of complex systems and enable the design of comprehensive solutions. Finally, open data science practices, such as sharing data and algorithms, can facilitate collaboration and accelerate progress in mitigating climate change and its public health impacts.In conclusion, AI offers promising opportunities for effectively addressing climate change and its impact on public health. However, to fully realize its potential, it is essential to tackle ethical and privacy concerns, overcome technical constraints, and ensure accessibility and affordability. By promoting innovation, multidisciplinary collaboration, and open data science, we can unlock the transformative power of AI in mitigating climate change and improving public health outcomes.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

Members of the genus Armillaria are widespread forest pathogens against which effective protection has not yet been developed. Due to their longevity and the creation of large-scale cloning of Armillaria individuals, the use of mycoviruses as biocontrol agents (BCAs) against these pathogens could be an effective alternative. This work describes the screening of double-stranded RNA banding patterns as a first approach for potential virus discovery and the use of stranded total RNA-seq for viral detection and characterization in Armillaria spp. collected in the Czech Republic. A total of five single-stranded RNA viruses were detected in Armillaria ostoyae and A. cepistipes, including the first virus of the family Tymoviridae found infecting a member the genus Armillaria and four viruses belonging to the recently described virus group "ambiviruses" with circular ambisense genome organization. Both hammerhead (HHRz) and hairpin (HpRz) ribozymes were detected in all the ambiviricot sequences. Armillaria viruses were compared by phylogenetic analysis and confirmed their specific host by direct RT-PCR, which showed the occurrence of interspecies transmission.

A common fault in turbomachinery is rotor--casing rub. Shaft vibration, measured with proximity probes, is the most powerful indicator of rotor-stator rub. However, in machines such as aeroderivative turbines, with increasing industrial relevance in power generation, constructive reasons prevent the use of those sensors, being only acceleration signals at selected casing locations available. This implies several shortcomings in the characterization of the machinery condition, associated with a lower information content about the machine dynamics. In this work we evaluate the performance of the Continuous Wavelet Transform to isolate the accelerometer signal features that characterize rotor-casing rub in an aeroderivative turbine. The evaluation is carried out on a novel rotor model of a rotor flexible casing system. Due to damped transients and other short-lived features that rub induces in the signals, the Continuous Wavelet Transform proves being more effective than both Fourier and Cepstrum Analysis. This creates the chance for enabling early fault diagnosis of rub before it may cause machine shutdown or damage.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

In this research paper, change detection based methods were considered to find collapsed and intact buildings using radar remote sensing data or radar imageries. Main task of this research paper is collection of most relevant scientific research in field of building damage assessment using radar remote sensing data. Several methods are selected and presented as best methods in present time, there are methods with using interferometric coherence, backscattering coefficients in different spatial resolution. In conclusion, methods are given in end, which show, which methods and radar remote sensing data give more accuracy and more available for building damage assessment. Low resolution Sentinel-1A/B radar remote sensing data are recomended as free available for monitoring of destruction degree in microdistrict level. Change detection and texture based method are used together to increase overall accuracy. Homogeneity and Dissimilarity GLCM texture parameters found as better for separation of a collapsed and intact buildings. Dual polarization (VV,VH) backscattering coefficients and coherence coefficients (before earthquake and coseismic) were fully utilized for this study. There were defined the better multi variable for supervised classification of none building, damaged and intact buildings features in urban areas. In this work, we were achieved overall accuracy 0.77, producer’s accuracy for none building is 0.84, for damaged building case 0.85, for intact building 0.64. Amatrice town was chosen as most damaged from 2016 Central Italy Earthquake.

Oedaleus decorus asiaticus, Calliptamus abbreviatus, Angaracris rhodopa, and Myrmeleotettix palpalis are the main grasshoppers that harm the natural grassland in the Hexi Corridor. In this study, the MaxEnt model was employed to identify the key environmental factors affecting the distribution of the four grasshoppers habitats and to assess their distribution under current and future climate change conditions. The aim was to provide a basis for grasshopper monitoring, prediction, and precise control. In this study, 61 occurrences of O. decorus asiaticus, 68 occurrences of A. rhodopa, 58 occurrences of C. abbreviatus, and 92 occurrences of M. palpalis were recorded by GPS, and the distribution of suitable habitats for O. decorus asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis were predicted under current and future climatic scenarios using a MaxEnt model. The average AUC and TSS values of the four grasshoppers were greater than 0.9, and the simulation results were excellent and highly reliable. The mean annual precipitation was the main factor limiting the current range of suitable areas for these four species. Under the current climate, O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the central and eastern parts of the Hexi Corridor, and M. palpalis was distributed throughout the Hexi Corridor, with a potential distribution area of 1.44×104, 1.43×104, 1.29×104, and 2.12×104 km2, accounting for 15.3, 15.2, 13.7, and 22.5% of the total area of the grasslands in the Hexi Corridor, respectively. The highly suitable areas of O. asiaticus, C. abbreviatus, and A. rhodopa were mainly distributed in the east-central part of Zhangye City, the western part of Wuwei City, and the western and southern part of Jinchang City, with areas of 0.35×104, 0.29×104, and 0.20×104 km2, accounting for 3.7, 3, and 2.2% of the grassland area, respectively. The high habitat of M. palpalis was mainly distributed in the southeast of Jiuquan City, the west, middle, and east of Zhangye City, the west of Wuwei City, and the west and south of Jinchang City, with an area of 0.32×104 km2, accounting for 3.4% of the grassland area. In the 2030s, the range of O. asiaticus, C. abbreviatus, A. rhodopa, and M. palpalis was predicted to decrease.

Pavement crack detection is one of the key links in highway pavement maintenance management. In the current road crack detection, the network model easily ignores the shallow geometric features of cracks and cannot extract the key feature information of cracks. Aiming at the above problems, an EC-YOLOX network model is proposed. The CFPN is constructed to cross-fuse different scale features to solve the feature scale invariance. In the strengthen feature extraction layer, ECANet is fused to enhance the ability to pay attention to key information. The WEIoU loss function is proposed, which assigns different penalty terms to the target box in the vertical and horizontal directions. In terms of data, geometric distortion constraint correction is performed on the single-point perspective pavement image. The experimental data show that the accuracy of EC-YOLOX on the self-built data set reaches 76.34% [email protected], which is 4.45% higher than that of YOLOX. The loss curve of EC-YOLOX is smoother than that of YOLOX, and the minimum training loss value is 2.136, which is 0.648 lower than the minimum loss value 2.784 of YOLOX. Many experiments have verified the effectiveness of EC-YOLOX in improving the detection effect in pavement crack detection.

In 2020, the world was plagued with COVID-19 which was first identified in Wuhan, China in November 2019. During the early phase of the pandemic with no known treatment and WHO-approved vaccines, most government and public health officials were pushing for non-pharmaceutical intervention in trying to curb the spread of COVID-19. One such intervention is the restriction on movement to reduce social mixing. However, the economic cost of locking down cities especially in developing countries is unbearable as most of these countries are running economies that were on life support before the COVID-19 pandemic. We analyze the daily COVID-19 cases in Ghana to evaluate whether there was a significant change in transmission of COVID-19 after the partial lockdown of the two main cities (Kumasi and Accra) was lifted. The results showed that there was no increase in the transmissibility of COVID-19 after the partial lockdown was lifted. Contrary to the expectation that transmissibility will increase after lifting the partial lockdown, there was a reduction of the time-dependent reproduction ratio from 3.17 to 1.23.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

In review, the operating principles of the most common bio sensing devices, detection methods and the identification sensitivity of analyzed molecules were shown. The central focus was done on hybridization analysis of nucleic acids (NA), which are considered to be one of the most important analytes in terms of diagnostic point of view. Constructions enabling to transfer the fact of formation of nucleotide probe/target complex in to detectable signal by optical, electrochemical or micromechanical (piezoelectric) sensors were presented in this review.

Deep learning techniques are increasingly being recognized as effective image classifiers. Aside from their successful performance in past studies, the accuracies have varied in complex environments in comparison with the popularly applied machine learning classifiers. This study seeks to explore the feasibility for using a U-Net deep learning architecture to classify bi-temporal high resolution county scale aerial images to determine the spatial extent and changes of land cover classes that directly or indirectly impact tidal marsh. The image set used in the analysis is a collection of a 1-m resolution collection of National Agriculture Imagery Program (NAIP) tiles from 2009 and 2019 covering Beaufort County, South Carolina. The U-net CNN classification results were compared with two machine learning classifiers, the Random Trees (RT) and the Support Vector Machine (SVM). The results revealed a significant accuracy advantage in using the U-Net classifier (92.4%) as opposed to the SVM (81.6%) and RT (75.7%) classifiers for overall accuracy. From the perspective of a GIS analyst or coastal manager, the U-Net classifier is now an easily accessible nad powerful tool for mapping large areas. Change detection analysis indicated little areal change on marsh extent, though increased land development throughout the county has the potential to negatively impact the health of the marshes. Future work should explore applying the constructed U-Net classifier to coastal environments in large geographic areas, while also implementing other data sources (e.g., LIDAR, multispectral data) to enhance classification accuracy.

Land cover change detection (LCCD) based on bi-temporal remote sensing images plays an important role in the inventory of land cover change. Due to the benefit of having spatial dependency properties within the image space while using remote sensing images for detecting land cover change, many contextual information based change detection methods have been proposed during past decades. However, there is still a space for improvement in accuracies and usability of LCCD. In this paper, a LCCD method based on adaptive contextual information is proposed. First, an adaptive region is constructed by gradually detecting the spectral similarity surrounding a central pixel. Second, the Euclidean distance between pairwise extended regions is calculated to measure the change magnitude between the pairwise central pixels of bi-temporal images. While the whole bi-temporal images are scanned pixel-by-pixel, the change magnitude image (CMI) can be generated. Then, the Otsu or a manual threshold is employed to acquire the binary change detection map (BCDM). The detection accuracies of the proposed approach are investigated by two land cover change cases with Landsat bi-temporal remote sensing images. In comparison to several widely used change detection methods, the proposed approach can achieve a land cover change inventory map with a competitive accuracy.

The rapid development of Deep Learning brought novel methodologies for 3D Object Detection using LiDAR sensing technology. These improvements in precision and inference speed performances lead to notable high performance and real-time inference, which is especially important for self-driving purposes. However, the developments carried by these approaches overwhelm the research process in this area since new methods, new technologies, and software versions lead to different project necessities, specifications and requirements. Moreover, the improvements brought by the new methods may be due to improvements in newer versions of deep learning frameworks and not just the novelty and innovation of the model architecture. Thus, it became crucial to create a framework with the same software versions, specifications and requirements that accommodate all these methodologies and allow the easy introduction of new methods and models. A framework is proposed that abstracts the implementation, reusing and building of novel methods and models. The main idea is to facilitate the representation of state-of-the-art (SoA) approaches and simultaneously encourage the implementation of new approaches by reusing, improving and innovating modules in the proposed framework, which has the same software specifications to allow a fair comparison. This makes it possible to determine if the key innovation approach outperforms the current SoA by comparing models in a framework with the same software specifications and requirements.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

Climate change is a global issue that draws widespread attention from the international society. As an important component of the climate system, the water cycle is directly affected by climate change. Thus, it is very important to study the influences of climate change on the basin water cycle with respect to maintenance of healthy rivers, sustainable use of water resources, and sustainable socioeconomic development in the basin. In this study, by assessing the suitability of multiple General Circulation Models (GCMs) recommended by the Intergovernmental Panel on Climate Change, Statistical Downscaling Model (SDSM) and Automated Statistical Downscaling model (ASD) were used to generate future climate change scenarios. These were then used to drive distributed hydrologic models (Variable Infiltration Capacity, Soil and Water Assessment Tool) for hydrological simulation of the Yangtze River and Yellow River basins, thereby quantifying the effects of climate change on the basin water cycle. The results showed that suitability assessment adopted in this study could effectively reduce the uncertainty of GCMs, and that statistical downscaling was able to greatly improve precipitation and temperature outputs in global climate mode. Compared to a baseline period (1961–1990), projected future periods (2046–2065 and 2081–2100) had a slightly decreasing tendency of runoff in the lower reaches of the Yangtze River basin. In particular, a significant increase in runoff was observed during flood seasons in the southeast part. However, runoff of the upper Yellow River basin decreased continuously. The results provide a reference for studying climate change in major river basins of China.

Accurate clinical diagnosis of patients presenting to primary care settings with acute sore throat remains challenging, often resulting in the over-prescribing of antibiotics. Using point-of-care tests (POCTs) to differentiate between respiratory infections is well-accepted, yet evidence on the application within primary care is sparse. We assessed the application of testing patients (n=160) from three family practices with suspected Streptococcal infections using rapid molecular tests (ID NOW Strep A2, Abbott). In addition to comparing clinical evaluation and prescription rates with either usual care or with testing, patients and staff completed a questionnaire about their experience of molecular POCT in primary care. The immediate availability of the result was important to patients (100%) and staff (≈90%) stated that molecular testing improved quality of care. Interestingly, only 22.73% of patients with a Centor score >2 tested positive for Strep A and overall, less than 50% of Centor scores 3 and 4 tested positive for Strep A with the ID NOW testing platform. The addition of rapid molecular POCTs to clinical assessment resulted in a 55- 65% reduction in immediate and deferred antibiotic prescriptions. The intervention was popular with patients and medical staff but was associated with increased cost and a longer appointment length.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Background: Microscopic examination of acid-fast stained sputum smears for detecting mycobacterial acid-fast bacilli (AFB) remains the most economical and readily available method for laboratory diagnosis of tuberculosis (TB). However, this conventional approach has limitations, including low sensitivity and labor-intensive procedures. Methods: An automated microscopy system incorporating artificial intelligence (AI) and machine learning for AFB identification was evaluated. The study was conducted at an Infectious Disease Hospital in Jiangsu Province, China, utilizing an intelligent microscope system (TB-Scan, Wellgen Medical, Kaohsiung). A total of 1,000 sputum smears were included in the analysis, with the system capturing digital microscopic images and employing an image recognition model to automatically identify and classify AFB. Referee technicians provided the gold standard for discrepant results. Results: The automated system demonstrated an overall accuracy of 95.00% (950/1,000), sensitivity of 91.24% (177/194), and specificity of 95.91% (773/806). Notably, the system identified 21 smears as positive that were previously reported as negative, with referee technicians confirming 17 of these as true positive and retracting the test results accordingly. Recalculating the performance, the accuracy increased to 96.70% (967/1,000), sensitivity to 91.94% (194/211), and specificity to 97.97% (773/789), with a false negative rate of 8.06% (17/211) and a false positive rate of 2.03% (16/789). Conclusions: The incorporation of AI and machine learning into an automated microscopy system demonstrated the potential to enhance the sensitivity and efficiency of AFB detection in sputum smears compared to conventional manual microscopy. This approach holds promise for widespread application in TB diagnostics and potentially other fields requiring labor-intensive microscopic examination.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

Few-shot object detection (FSOD) aims to address the challenge of requiring a substantial amount of annotations for training in conventional object detection, which is very labor-intensive. However, existing few-shot methods achieve high precision with the sacrifice of time-consuming for exhaustive fine-tuning, or take poor performance in novel-class adaptation. We presume the major reason is that the valuable correlation feature among different categories is insufficiently exploited, hindering the generalization of knowledge from base to novel categories for object detection. In this paper, we propose Few-Shot object detection via Correlation-RPN and Transformer Encoder-Decoder (CRTED), a novel training network to learn object-relevant features of inter-class correlation and intra-class compactness while suppressing object-agnostic features in the background with limited annotated samples. And we also introduce a 4-way tuple-contrast training strategy to positively activate the training progress of our object detector. Experiments over two few-shot benchmarks (Pascal VOC, MS-COCO) demonstrate that, our proposed CRTED without further fine-tuning can achieve comparable performance with current state-of-the-art fine-tuned works. The codes and pre-trained models will be released.

Large datasets play a crucial role in the progression of surgical robotics, facilitating advancements in the fields of surgical task recognition and automation. Moreover, public datasets enable the comparative analysis of various algorithms and methodologies, thereby assessing their effectiveness and performance. The ROSMA (Robotics Surgical Maneuvers) dataset provides 206 trials of common surgical training tasks performed with the da Vinci Research Kit (dVRK). In this work, we extend ROSMA dataset with two annotated subsets: ROSMAT24, which contains bounding box annotations for instrument detection, and ROSMAG40, which contains high and low level gesture annotations. We propose an annotation method that provides independent labels for the right-handed tool and the left-handed tool. For instrument identification, we validate our proposal with a YOLOv4 model in two experimental scenarios. We demonstrate the generalization capabilities of the network to detect instruments in unseen scenarios. For gesture segmentation, we propose two label categories: high-level annotations that describe gestures at a maneuvers level, and low-level annotations that describe gestures at a fine-grain level. To validate this proposal, we have designed a recurrent neural network based on a bidirectional long-short term memory layer. We present results for four cross-validation experimental setups, reaching up to a 77.35% mAP.

The objective of this study was to determine how application with dolomitic limestone and grazing type (continuous or deferred) affect sheep grazing location and feed preference when the pasture growth rate is maximum. A 4ha field was divided into 4 plots: P1 and P2- without application of dolomitic limestone, continuous (CG) and deferred grazing (DG), respectively; P3 and P4- with application of dolomitic limestone, DG (1AUE), and CG (2.4 AUE), respectively. In DG, animals were placed and removed from the plots depending on the height of the pasture. In each plot, 12 georeferenced sampling points were identified. Throughout the pasture's vegetative cycle (autumn, winter, spring, and early summer) several measurements of pasture height and cut were carried out. From the beginning of March to the beginning of June, animal behavior was observed, by trained observers, through binoculars on six dates. Animals' activity grazing and location was recorded. The results show that: (i) the application of dolomitic limestone combined with CG provided higher values of pasture height; (ii) there were no significant differences in pasture quality between treatments; (iii) Deferred grazing led to 50% more sheep grazing days than continuous grazing; (iv) there were no significant differences in soil compaction between CG and DG; (v) the type of grazing and the treatment with dolomitic limestone did not seem to change the grazing pattern between treatments. This work contributes to understanding the relationships between different types of grazing in dryland pastures, with and without application of dolomitic limestone, and preferred grazing locations for sheep. This work could help agricultural managers make more informed decisions with the aim of promoting the sustainable intensification of livestock production in the Montado ecosystem.

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

The point cloud is a form of three-dimensional data that comprises various detailed features at multiple scales. Due to this characteristic and its irregularity, point cloud analysis based on deep learning is challenging. While previous works utilize the sampling-grouping operation of PointNet++ for feature description and then explore geometry by means of sophisticated feature extractors or deep networks, such operations fail to describe multi-scale features effectively. Additionally, these techniques have led to performance saturation. And it is difficult for standard MLPs to directly "mine" point cloud. To address above problems, we propose the Detail Activation (DA) module, which encodes data based on Fourier transform after sampling and grouping. We activate the channels at different frequency levels from low to high in the DA module to gradually recover finer point cloud details. As training progresses, the proposed Point-MDA can uncover local and global geometries of point cloud progressively. Our experiments show that Point-MDA achieves superior classification accuracy, outperforming PointNet++ by 3.3% and 7.9% in terms of overall accuracy on the ModelNet40 and ScanObjectNN dataset, respectively. Furthermore, it accomplishes this without employing complicated operations, while exploring the full potential of PointNet++.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

Exposure to malachite green (MG) may pose great health risks to humans, thus it is of prime importance to develop fast and robust methods to quantitatively screen the presence malachite green in environment. Herein application of extractive electrospray ionization mass spectrometry (EESI-MS) has been extended to the trace detection of MG within lake water and aquiculture water, due to the intensive use of MG as biocide in fisheries. This method has the advantage of obviating offline liquid-liquid extraction or tedious matrix separation prior to the measurement of malachite green in native aqueous medium. The experimental results indicate that the extrapolated detection limit for MG was ~3.8 ug L-1 (S/N=3) in lake water samples and ~ 0.5 ug L-1 in ultrapure water under optimized experimental conditions. The signal intensity of MG showed good linearity over the concentration range of 10–5000 ug L-1. Measurement of practical water samples fortified with MG at 0.01 and 0.1 mg L-1 gave a good validation of the established calibration curve. The average recoveries of malachite green in lake water and Carassius carassius fish farm effluent water were 114.9% (6.6% RSD) and 85.4% (9.2% RSD), respectively. Overall, the established EESI-MS/MS method has been demonstrated suitable for sensitive and rapid (<2 min per sample) quantitative detection of malachite green in various aqueous media, indicating its potential for online real-time monitoring of real life samples.

This study proposes a machine-learning-based framework for detecting mechanical damage in pipelines, utilizing physics-informed datasets collected from simulations for mechanical damage. The framework provides an effective workflow from dataset generation to damage detection and identification for three types of pipeline events: welds, clamps, and corrosion defects. While the study initially focused on optimizing the CNN structure using various advanced optimizers, it also investigated the impact of sensing systems on data classification and the effect of noise on classification performance. The study's analysis highlights the importance of selecting the appropriate sensing system for the specific application. The authors also found that the proposed framework is robust to experimentally relevant levels of noise, suggesting its applicability in real-world scenarios where noise is present. Overall, this study contributes to the development of a more reliable and effective method for detecting mechanical damage in pipelines. The proposed framework provides an effective workflow for damage detection and identification, and the findings on the impact of sensing systems and noise on classification performance add to its robustness and reliability.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

Detection of subsurface archaeological remains using a range of remote sensing methods, poses several challenges until today. Recent studies regarding the detection of archaeological proxies like those of cropmarks highlight the complexity of the phenomenon. In this work we present three different methods, and associated indices, for identifying stressed reflectance signatures indicating buried archaeological remains, based on a dataset of measured ground spectroradiometric reflectance. Several spectral profiles between the visible and near infrared part of the spectrum, were taken over a controlled environment in Cyprus during the 2011-2012 and are re-used in this study. The first two (spectral) methods are based on a suitable analysis of the spectral signatures in (1) the visible part of the spectrum, and in particular in the neighborhood of 570 nm, and (2) the red edge-near infrared part of the spectrum, in the neighborhood of 730 nm. Machine learning (decision trees) allows for the deduction of suitable wavelengths to focus on, in order to formulate the proposed indices and the associated classification criteria (decision boundaries) that can enhance the detection probability of stressed vegetation. Noise in the signal is taken into account by simulating reflectance signatures perturbed by white noise. Applying decision tree classification on the ensemble of simulations and basic statistical analysis we refine the formulation of the indices and criteria for the noisy signatures. The success rate of the proposed methods is over 90%. The third method rests on the estimation of vegetation/canopy reflectance parameters through inversion of the physical-based PROSAIL reflectance model and the associated classification through machine learning methods. The obtained results provide further insights into the formation of stress vegetation that occurred due to the presence of shallow buried archaeological remains, which are well aligned with physical-based models and existing empirical knowledge. To the best of the authors' knowledge, this is the first study demonstrating the usefulness of radiative transfer models such as PROSAIL for understanding the formation of cropmarks. Similar studies can support future research directions towards the development of regional remote sensing methods and algorithms if systematic observations are adequately dispersed in space and time.

Over the past couple of decades, Global positioning system (GPS) technology has been utilized to collect large-scale data from travel surveys. As the precise spatiotemporal characteristics of travel could be provided by GPS devices, the issues of traditional travel survey, such as misreporting and non-response, could be addressed. Considering the defects of dedicated GPS devices (e.g., need much money to buy devices, forget to take devices to collect data, limit the simple size because of the number of devices, etc.), and the phenomenon that the smartphone is becoming one of necessities of life, there is a great chance for the smartphone to replace dedicated GPS devices. Although, several general reviews have been done about smartphone-based GPS travel survey in the literature review section in some articles, a systematic review from smartphone-based GPS data collection to travel mode detection has none. The included studies were searched from six databases. The purpose of this review is to critically assess the current literature on the existing methodologies of travel mode detection based on GPS raw data collected by smartphones. Meanwhile, according to the systematic comparison among different methods from data-preprocessing to travel mode detection, this paper could carefully provide the Strengths and Weaknesses of existing methods. Furthermore, it is the crucial step to develop the methodologies and applications of GPS raw data collected by smartphones.

Interactions between mobile robots and human operators in common areas require a high safety especially in terms of trajectory planning, obstacle avoidance and mutual cooperation. In this connection the crossings of planned trajectories, their uncertainty based on model fluctuations, system noise and sensor noise,play an outstanding role. This paper discusses the calculation of expected areas of interactions du ring human-robot navigation with respect to fuzzy and noisy information. Expected crossing points of possible trajectories are nonlinearily associated with positions and orientations of robot and human. The nonlinear transformation of a noisy system input, such as directions of motion of human and robot, to a system output, the expected area of intersection of their trajectories, is done by two methods: statistical linearization and the sigma-point-transformation. For both approaches fuzzy approximations are presented and the inverse problem is discussed where the input distribution parameters are computed from given output distribution parameters.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

Congenital heart disease (CHD) is a prevalent congenital disorder diagnosed with high frequency, affecting approximately 0.8% to 1.2% of all live births. Research has demonstrated that the use of pulse oximetry and clinical examination as a screening tool for CHD diagnosis has proven extremely valuable. We conducted a retrospective longitudinal study over a 3-year period that involved screening 1188 newborns admitted to the NICU during the first 72 hours of life within this timeframe. 201 newborns were diagnosed with CHD. Almost all (n=198) had a positive screening test during the 72-hour period, while 3 had a negative screening test, but were later diagnosed using echocardiography. The prevalence rate was 16.67%. A confusion matrix was constructed with 198 true positives (TP), 3 false negatives (FN), no false positives (FP), and 987 true negatives (TN). The sensitivity of the screening test was 98.51%, while the specificity 100%, with no false positives. In our study, a total of 9 deaths occurred. Using the Kaplan-Meier method, the survival probability appeared to be slightly above 0.9 (95.5%), indicating that almost all patients survived past 72 hours after being diagnosed with CHD. Pulse oximetry is an effective, low cost and easy-to-use method and a useful tool to assess and lead to the diagnosis of CHD.

Deadlock is a real problem that can cause expensive, time-dependent hang-ups or failures in distributed computing systems. Some studies have been conducted with deadlock detection and resolution in generalized request computing models, most of these studies are based on the diffusing computation scheme, where forward and backward propagated probe and reply messages respectively are diffused between dependent processes. The replies carry the dependency information between processes for the initiator. Using this dependency information initiator can detect and resolve the deadlock cycle. It has been proven in the literature that a deadlock cycle length distribution is skewed with a large majority of cycles (90%) having length two. Based on this fact an improved algorithm is proposed for handling deadlock detection in distributed computing systems under the distributed request model where each process has several requests at a time. The improved algorithm depends mainly on message propagation and timeout policy. Probe and reply messages are propagated between the initiator and its successors only to detect deadlock cycles between them. Global timeout policy is used to detect potential deadlock cycles with large length distribution. The proposed algorithm can handle concurrent executions. Simulation experiments are performed to see the effectiveness of the improved algorithm. It is found that the improved algorithm compares favorably with other existing algorithms and it shows better results for several performance metrics especially in reducing deadlock latency and execution time.

Achieving the dual development of rural revitalization and urbanization is an important strategic goal of China’s current modernization. Rural population and settlements are the main components of the countryside in traditional agricultural areas, and play an important role in the development of the countryside itself in terms of urban and rural land use and in the formation of urban and rural development patterns. This study analyzes the spatial and temporal changes in rural populations and settlements at the township level, as well as the degree and type of coupled development. A framework for urban–rural development relationships based on different types of coupled development is proposed, and a model of urban–rural forces is constructed to derive the spatial pattern of urban–rural development at the township level that may be formed in the future. Our study shows that the rural population and settlements in the study area are characterized by significant spatial and temporal dynamics, indicating that traditional rural areas are in a process of rapid development and change. The results of the township-level coupling measurements present four types of development in terms of the spatial pattern of urban–rural development: A-type is most likely to produce new cities or satellite towns in the Jixi–Harbin–Qiqihar area in the future; B-type is the fastest dying area in the future, located in the Harbin and Qitaihe clusters, with a tendency to merge into Harbin; C-type is the area to be focused on in the future to attract population and strictly control the growth of the rural settlement area to avoid it turning into B-type; D-type may develop regional township centers in the future in the combined area of Jiamusi City, Suihua City and Mudanjiang City. The results of the study provide experience in realizing rural revitalization according to local conditions. The new spatial pattern of urban–rural development provides an important reference for formulating land use policies, optimizing urban–rural land allocation and realizing integrated urban–rural development strategies.

Change detection with heterogeneous remote sensing images (Hete-CD) plays an important role in practical applications, especially when homogenous remote sensing images are unavailable. However, bitemporal heterogeneous remote sensing images (HRSIs) cannot compare directly to measure change magnitude, and many deep learning methods require large amounts of samples to train the module. Moreover, labeling many samples for land cover change detection with HRSIs is time-consuming and labor-intensive. Therefore, acquiring satisfactory performance of Hete-CD remains a challenge for deep learning networks with very small training samples. In this study, we promote a novel deep-learning framework for Hete-CD to obtain satisfactory performance while the initial samples are very small. We initially design a multiscale network with select kernel-attention module to focus on capturing different change targets with various sizes and shapes. Then, a simple yet effective non-parametric sample-enhanced algorithm based on the Pearson correlation coeffi-cient is promoted to explore potential samples around each initial sample. Finally, the proposed network and sample-enhanced algorithm are fused into one iterative framework to improve the change detection performance with very small samples. Experimental results conducted on four pairs of actual HRSIs indicated that the proposed framework can achieve competitive accuracies with very small samples for initialization when compared with some state-of-the-art methods. For example, the improvement is approximately 3.38% and 1.99% when compared with the selected traditional methods and deep learning methods, respectively.

Precise monitoring of individual crop growth and health status is crucial for precision agriculture practices. However, traditional manual inspection methods are time-consuming, labor-intensive, and often lack the spatial resolution required for detailed analysis. This research addresses the need for efficient and high-resolution crop monitoring by leveraging Unmanned Aerial Vehicle (UAV) imagery and advanced computational techniques. The primary objective was to develop a methodology for precise identification, extraction, and monitoring of individual corn crops throughout their growth cycle. This was achieved by integrating UAV-derived data with image processing, computational geometry, and machine learning techniques. UAV imagery was ac-quired bi-weekly at altitudes of 40m and 70m, capturing the entire growth cycle of a corn crop from planting to harvest. A time-series Canopy Height Model (CHM) was generated by analyzing the differences between the Digital Terrain Model (DTM) and the Digital Surface Model (DSM) derived from the UAV data. Local spatial analysis and image processing techniques were em-ployed to determine the local maximum height of each crop. Subsequently, a Voronoi data model was developed to delineate individual crop canopies, successfully identifying 13,000 out of 13,050 corn crops in the study area. For enhanced accuracy in canopy size delineation, vegetation indices were incorporated into the Voronoi model segmentation, refining the initial canopy area esti-mates by eliminating interference from soil and shadows. The proposed methodology enables precise estimation and monitoring of crop canopy size, height, biomass reduction, lodging, and stunted growth over time, providing valuable insights for precision agriculture practices. This work contributes to the scientific community by demonstrating the potential of integrating UAV technology, computational geometry, and machine learning for accurate and efficient crop mon-itoring at the individual plant level.

The intentional damages to local Cultural Heritage sites carried out in recent months by the Islamic State have received wide coverage from the media worldwide. Earth Observation data provide important information to assess these damages in such non-accessible areas, and automated image processing techniques would be needed to speed up the analysis if a fast response is desired. This paper shows the first results of applying fast and robust change detection techniques to sensitive areas, based on the extraction of textural information and robust differences of brightness values related to pre- and post-disaster satellite images. A map highlighting potentially damaged buildings is derived, which could help experts at timely assessing the damages to the Cultural Heritage sites of interest. Encouraging results are obtained for two archaeological sites in Syria and Iraq.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Crop productivity is directly dependent to soil fertility. High soil organic carbon (SOC) content in soil is vital as it leads to improved soil quality, increased productivity, and stable soil-aggregates. In addition, with the signing of the climate agreement, there is growing interest in carbon sequestration in landscapes. This paper looks at how SOC can be increased so that it not only contributes to reduction of CO₂, but also translates to increased food production thereby enhancing food security. This synergy between mitigation and enhancing food security is even more relevant for mountain landscapes of the Hindu Kush Himalayan (HKH) region where there remains huge potential to increase CO₂ sequestration and simultaneously address food security in the chronic food deficit villages. Soil samples were collected from seven transects each in Bajhang and Mustang and from 4 land use types in each transect. Samples of soils were taken from two depths in each plot; 0-15 cm below the soil surface and 15-30 cm below the soil surface to compare the top soil and subsoil dynamics of the soil nutrients. The lab analysis was performed to assess the soil texture, soil color, soil acidity in 'power of hydrogen' (pH), macro-nutrients as soil fertility. Secondary data was used to analyze the level of food deficit in the villages. The result shows that most of the sample soils from Mustang were clay (82.1%) which is 46 samples out of 56. The pH value of soil from Bajhang ranged from 5.29 to 9.09. The pH value of soil ranged from 5.65 to 8.81 in Mustang. SOC contents of sampled soils from Bajhang ranged from 0.20% to 7.69% with mean amount of 2.47% ± 0.17. SOC contents of sampled soils from Mustang ranged from 0.51% to 8.56% with mean amount of 2.60% ± 0.25. By land use type, forest land had the highest carbon (C) content of 53.61 t ha^-1 in Bajhang whereas in Mustang, agricultural land had the highest C content of 52.02 tons ha-1. Based on these data, we can say that there is potential for increasing SOC through improved soil health and crop production and soil. Sustainable soil management should be practiced for higher productivity. Livestock may also provide farmyard manure, which can be used to fertilize cultivated soils, which increases soil productivity. Increasing productivity would aid in increasing the access and availability of food in these mountain villages.

The presence of antibiotic residues in honey has recently become a growing public health concern due to the overuse of these products in beekeeping and their transfer to the food industry. The aim of this study was to develop and validate a simple, selective and sensitive method for the simultaneous identification and quantification of residues of twenty-two sulfonamides, trimethoprim and dapsone in honey using a rapid and reliable liquid chromatography–tandem mass spectrometry (LC–MS/MS) method. The developed method showed good linearity, specificity, precision (repeatability and intra-laboratory reproducibility) and recovery. The decision limit (CCalpha) ranged between 2.16-22.12 µg/kg for CCα, while the detection capability (CCbeta) was between 2.16- 2.67-27.36 µg/kg. The method proved to be rapid, reliable and effective for the determination of sulfonamides, trimethoprim and dapsone from honey samples. The average recoveries were estimated to be between 70 and 106%. The relative standard deviations (RSDs) were between 6-18%. In practice, the method is essential to check the honey sold on the market and ensure its safety before it reaches the consumer.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.