This paper addresses the problem of low accuracy of conventional channel estimation and signal detection in complex fields like mines; and the problem of replacing the deep receiver at the receiver side with a deep neural network requires a large amount of data for training and slow training time. Combining the receiver side with traditional communication knowledge, a channel estimation and signal detection method based on the joint ReEsNet and SDRNet under the mine is proposed. The detailed step is to use ReEsNet network for interpolation of conventional channel estimation. Then, on the basis of ReEsNet, the output data is channel equalized and pilots removed, and the previously processed data is input to SDRNet to perform signal recovery. In the complex mine environment, the MSE values are 2e-2 for LS, 6e-3 for MMSE, and 8.44e-5 for ReEsNet at the 1500th sample data for interpolation compared to the conventional channel estimation. the MSE of ReEsNet is the smallest and is closer to the real channel estimation. Compared with the proposed joint channel estimation and signal detection methods, fewer trainable parameters reduce 97% of the parameters compared to CCRNet and 84% of the parameters compared to CNNNet; their detection results, however, are not very different.

This paper proposes the use of compressive sensing to tackle the Massive MIMO channel estimation problem. As our results show compressive sensing-based estimators perform as well as the optimum MMSE estimator.

Fractional delay-Doppler (DD) channel estimation in Orthogonal Time Frequency Space (OTFS) systems poses a significant challenge considering the severe effects of Inter-Path Interference (IPI). To this end, several algorithms have been extensively explored in literature for accurate low-complexity channel estimation in both integer and fractional DDs scenarios. In this work, we develop a variant of the state-of-the-art Delay-Doppler Inter-Path Interference Cancellation (DDIPIC) algorithm which progressively cancels the IPI as estimates are obtained. The key advantage of the proposed approach is that it requires only a final refinement procedure reducing the complexity of the algorithm. Specifically, the time difference in latency between the proposed approach and the DDIPIC algorithm is almost proportional to the square of the number of estimated paths. Numerical results show that the proposed algorithm outperforms the other channel estimation schemes achieving lower Normalized Mean Square Error (NMSE) and Bit Error Rate (BER).

Channel estimation is an important module to enhance the performance of orthogonal frequency division multiplexing (OFDM) systems. However, the presence of a large amount of noise in multipath fading time-varying channels significantly affects the channel estimation accuracy and thus the recovery quality of the received signals. Therefore, this paper proposes a double-threshold (DT) channel estimation method based on adaptive frame statistics (AFS). The method first adaptively determines the number of statistical frames based on the temporal correlation of the received signals, and preliminarily detects the channel structure by analyzing the distribution characteristics of multipath sampling points and noise sampling points during adjacent frames. Subsequently, a multi-frame averaging technique is used to expand the distinction between multipath and noise sampling points. Finally, the DT is designed to better recover the channel based on the preliminary detection results. Simulation results show that the proposed adaptive frame statistics-double-threshold (AFS-DT) channel estimation method is effective and has better performance compared with many existing channel estimation methods.

With the dramatic increase in the number of mobile users and wireless devices accessing the network, the performance of the fifth generation (5G) wireless communication systems has been severely challenged. Reconfigurable intelligent surfaces (RIS), one of the potential technologies for the sixth generation (6G), has received a lot of attention. Since it is easier to deploy, consumes less power, and is inexpensive. RIS is an electromagnetic metamaterial that serves to reconfigure the wireless environment by adjusting the phase, amplitude and frequency of the wireless signal. To maximize channel transmission efficiency and improve the reliability of communication systems, the acquisition of channel state information (CSI) is essential. Therefore, an effective channel estimation method guarantees the achievement of excellent RIS performance. This paper conducts a comprehensive investigation of the existing channel estimation methods of RIS, analysis and comparison of channel model building and CSI acquisition schemes in different frequency bands, in addition to a comprehensive description of generic channel estimation methods, with a focus on the application of deep learning. Finally, we conclude the paper and provide an outlook in the future development of RIS channel estimation.

Starting from the model of a slow-rolling missile with six degrees of freedom (6 DOF) in the body frame, a 6 DOF model in the Resal frame is obtained, which is used to linearize the coupled commanded motion. Based on the linearized model, we obtain the structural scheme of the commanded object and define the quality parameters. The obtained parameters have a complex representation (with real and imaginary parts) due to the coupling between longitudinal channels. Then, the kinematic guidance equations, the seeker equations and the actuator specific to the slow-rolling single-channel missile are defined using a switching function. The guidance kinematic equations, the seeker equations and the actuator model are linearized in the Resal frame, and the structural diagram of the homing missile is constructed. Starting from this, the characteristic polynomial having complex coefficients is determined and then analyzed with the Frank-Wall stability criterion. Based on the analysis, a stability range is determined for the navigation constant and a minimum and possibly a maximum limit for the time to hit the target is obtained. The stability range defined for the navigation constant on the linear model is finally validated on the nonlinear model in the body frame.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

Dynamic systems which underly controlled systems are expected to increase in complexity as robots, devices, and connected networks become more intelligent. While classical stable systems converge to a stable point (a sink), another type of stability is to consider a stable path rather than a single point. Such stable paths can be made of saddles which draw in trajectories from certain regions, and then push the trajectory toward the next saddle point. These are chains of saddles are called stable heteroclinic channels (SHCs), and can be used in robotic control to represent time sequences. While we have previously shown that each saddle is visualizable as a trajectory waypoint in phase space, how to increase the fidelity of the trajectory was unclear. In this paper, we hypothesized that the waypoints can be individually modified to locally vary fidelity. Specifically, we expected that increasing the saddle value (ratio of saddle eigenvalues) causes the trajectory to slow to more closely approach a particular saddle. Combined with other parameters that control speed and magnitude, a system expressed with an SHC can be modified locally, point by point, without disrupting the rest of the path, supporting their use in motion primitives. However, even more complex trajectory shape modifications are possible. While some combinations can enable a trajectory to better reach into corners, other combinations can rotate, distort and round the trajectory in the region of a corner. In our example, modifying select saddle values produced a 32% decrease in the trajectory error of a complex trajectory produced using this system. This is an effect not visible in previous 1D studies, that can lead to different learnable and tunable representations of dynamic systems.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Dielectric Elastomer Actuators (DEAs) are emerging as promising candidates for various applica-tions in robotics and optical devices due to their lightweight, miniaturization potential, high en-ergy density, simple structure, and low power consumption. However, their effective actuation always demands sophisticated high-voltage driving circuits that are compact and responsive. DEAs need to be capable of generating intricate high-voltage waveforms or simultaneously con-trolling multiple channels with distinct high-voltage levels. This paper proposes a high-voltage power supply for DEAs, featuring a four-channel high-voltage driving circuit. The circuit is ca-pable of independently generating high-voltage signals ranging from 100 V to 6000 V and can be programmed to produce arbitrary waveforms with adjustable frequencies. The independent op-eration of channels without crosstalk showcases the system's integration and potential for cross-disciplinary applications.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Presynaptic Ca²⁺-influx through voltage-gated Ca²⁺ channels (VGCC) is a key signal for synaptic vesicle release. Synaptic neurexins can partially determine the strength of transmission by regulating VGCCs. However, it is unknown whether neurexins modulate Ca²⁺-influx via all VGCC subtypes similarly. Here, we performed live cell imaging of synaptic boutons from primary hippocampal neurons with a Ca²⁺-indicator. We used the expression of inactive and active Cre recombinase to compare control to conditional knockout neurons lacking either all or selected neurexin variants. We found that reduced total presynaptic Ca²⁺-transients caused by the deletion of all neurexins were primarily due to the reduced contribution of P/Q-type VGCCs. The deletion of neurexin1α alone also reduced the total presynaptic Ca²⁺-influx but increased Ca²⁺-influx via N-type VGCCs. Moreover, we tested whether the decrease of Ca²⁺-influx induced by activation of cannabinoid receptor 1 (CB1-receptor) is modulated by neurexins. Unlike earlier observations emphasizing a role for β-neurexins, we found that the decrease of presynaptic Ca²⁺-transients induced by CB1-receptor activation depended more strongly on the presence of α-neurexins in hippocampal neurons. Together, our results suggest that neurexins have unique roles in the modulation of presynaptic Ca²⁺-influx through VGCC subtypes and that different neurexin variants may affect specific VGCCs.

Assessing the quality of corn seeds necessitates evaluating their content of water, fat, protein, and starch. This study integrates hyperspectral imaging technology with chemometric analysis techniques to achieve non-invasive and rapid detection of multiple key components in corn seeds. Hyperspectral images of the embryo surface of maize seeds were collected within the wavelength range of 1100~2498nm. Subsequently, image segmentation techniques were applied to extract the germ structure of the corn seeds as the region of interest. Seven spectral data preprocessing algorithms were employed, and the Detrending Transformation (DT) algorithm was identified as the optimal preprocessing method through comparative analysis using the Partial Least Squares Regression (PLSR) model. To reduce spectral redundancy and streamline the prediction model, three algorithms were employed for characteristic wavelength extraction: Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS), and Uninformative Variable Elimination (UVE). Using both the original spectra and the extracted characteristic wavelengths, four content detection models were constructed: PLSR, Back Propagation Neural Network (BPNN), Radial Basis Function Neural Network (RBFNN), and Least Squares Support Vector Machine (LSSVM). The experimental results demonstrate that the DT-CARS-LSSVM model exhibits exceptional accuracy and stability in predicting these four key components, with determination coefficients of 0.9877, 0.9344, 0.9827, and 0.9592, respectively. This study not only provides a scientific basis for evaluating the quality of corn seeds but also opens up new avenues for the development of non-invasive detection technology in related fields.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

Nowadays, considering the growing tendency of companies towards e-commerce as well as green production, and dual-channel green supply chain management has become particularly important. This paper investigates pricing decisions within a dual-channel green supply chain framework while considering the capital constraints faced by risk-averse manufacturer. Simultaneously, the impact of the degree of risk aversion, consumer green preferences, and channel preferences on the optimal decision-making process of green supply chain members is analyzed. We address the issue of financial constraints faced by manufacturer through bank loans and trade credit financing and compare the two cases. Our findings illustrate that trade credit financing outperforms bank loan financing in the dual-channel green supply chain. Moreover, pricing decisions under different models are influenced by consumer preferences and risk aversion. Specifically, the greenness of the product, wholesale price, and sale price exhibit negative correlations with manufacturers' risk aversion but positive correlations with consumer preferences.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity and low cost. However, the thorniest issue for wider application of IRT is the quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Carbon Fiber Reinforced Polymer(CFRP) embedded with flat bottom holes were designed via Finite Element Method (FEM) modeling in order to precisely control the depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

Variable flow emitters are a new type of emitter for underground drip irrigation that are used in locations where soil moisture is difficult to transport to the surface, which leads to crop emer-gence difficulties. The flow channel structure parameters of emitters affect the hydraulic per-formance of the emitter and its anticlogging ability. In this study, the variable flow emitter at the conventional low–flow water supply stage is taken as the research object. A combination of CFD numerical simulation of a two–phase flow of water and sand and clear water testing of test samples is applied to study the influence laws of 10 groups of variable flow emitter structural combinations on the effluent flow rate (q), flow index (x), particle passage rate and flow field inside the flow channel. The results show that the Realizable k–ε turbulence model can be used to simulate the flow field inside the variable flow emitter flow channel. The nRMSE between the measured and simulated values of q is 11.23%, and the relative error between the measured and simulated values of x is 4.66%, which gives a high simulation accuracy. The polar analysis shows that the tooth angle A has the smallest effect on the effluent flow rate q0.1 under 0.1 MPa, x, and particle passage rate of the variable flow emitter. The depth of the flow channel D, the spacing of the teeth B, and the height of the teeth E have a different order of precedence in the influence of the three indices, which are D > B > E > A, B > E > D > A, and E > B > D > A, respectively. The value of particle passage rate is positively correlated with the mean flow velocity (v) and the mean turbulent kinetic energy (k) in the flow channel, and particle passage rate tends to increase and then decrease with the increase of x. The retention time (t) of the particles in the flow channel is closely related to the magnitude of v and k. Three multivariate linear regression equations (R2 = 0.883 ~ 0.995) were constructed for q0.1, x, and particle passage rate versus the flow channel structural parameters. Using the scipy.optimize.minimize function in Python, we de-termined the three optimal combinations of flow channel structural parameters corresponding to better hydraulic performance: q0.1 is 1.5 or 2 L/h (objective function y = min x), better clogging resistance (y = max particle passage rate), and both (y = min (0.5 x - 0.5 particle passage rate)). The research results can provide a ref-erence for the optimal design of variable flow emitters.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

A basic limitation of the periodogram as frequency estimator is that any of its significant peaks may be produced by a diffuse (or spread) frequency component instead of a pure one. Diffuse components are common in applications such as channel estimation in which a given periodogram peak reveals the presence of a complex multipath distribution (unresolvable propagation paths or diffuse scattering, for example). We present a method to detect the presence of a diffuse component in a given peak based on analyzing the projection of the data vector onto the span of the signature’s derivatives up to a given order. Fundamentally, a diffuse component is detected if the energy in the derivatives’ subspace is too high at the peak’s frequency, and its spread is estimated as the ratio between this last energy and the peak’s energy. The method is based on exploiting the signature’s Vandermonde structure through the properties of discrete Chebyshev polynomials. We also present an efficient numerical procedure for computing the data component in the derivatives’ span based on barycentric interpolation. The paper contains a numerical assessment of the proposed estimator and detector.

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

This study provides a detailed numerical assessment of the productivity of single-slope solar stills across key cities in the Caspian region, including Aktau, Atyrau, Astrakhan, Makhachkala, Baku, Tehran, and Turkmenbashi. Employing a mathematical model based on heat balance equations and the 4th-order Runge-Kutta method, we simulated the distillation process under various climatic conditions. The results reveal that productivity is significantly influenced by geographic location and local meteorological conditions. Tehran demonstrated the highest productivity across all seasons, with values of 1.75 × 10³ kg/(m²·year) and an efficiency of 0.53, due to its optimal solar irradiation and ambient temperature. In contrast, Atyrau and Makhachkala exhibited lower productivity, particularly in colder months, highlighting the effect of ambient temperature on solar still efficiency. The analysis identified optimal water depth at 2 cm and insulation thickness between 4 and 9 cm for enhancing productivity in continental climates like Aktau. Additionally, the lowest cost of distilled water was $0.024 per kilogram in Baku. These findings align with existing literature, validating the numerical model's accuracy. Future research will explore integrating solar stills with other renewable and fossil fuel-based technologies.

Hypertension is a frequent risk factor for cardiovascular diseases and the prevalence rate is continuously rising. Multiple pathophysiological mechanisms are responsible for hypertension, necessitating a combination of drugs from different classes for best management. Combination therapy is five times more effective in decreasing blood pressure compared to escalating the dose of a single agent. As per the ACCOMPLISH trial analysis, coupling a renin-angiotensin system inhibitor with a calcium channel blocker is more effective than the combination of a renin-angiotensin system inhibitor with diuretics in reducing major cardiovascular events, cardiovascular-related mortality, and the progression of chronic kidney disease. The renin-angiotensin system can be suppressed by inhibiting the angiotensin-converting enzyme or angiotensin type 1 receptor (AT1R), resulting, in decreased vascular smooth muscle contraction, heart performance, and reduced aldosterone synthesis. Calcium channel blockers work by inhibiting L-type calcium channels, reducing heart performance via negative inotropic, chronotropic, and bathmotropic effects, along with reducing vascular smooth muscle contraction. Diuretics exert their antihypertensive impact by changing body fluid volume and electrolytes. Initially, hypertension treatment commences with a single medication but often, different classes of two or more antihypertensive medications are necessary for achieving the target blood pressure goal. Sometimes, for Resistant hypertension four different classes of antihypertensive medications are necessary to reach the target blood pressure goal.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Time estimation was investigated in 24 healthy adults, 12 women and 12 men, before and after an exhaustive exercise. We compared the capability of estimating time intervals in the range from 1 to 5 s using tasks requiring mental count and tasks that did not allow the mental count. Time estimation and blood lactate levels were evaluated before and at the end of the exercise. We found that the perception of time intervals between 1 and 5 s was affected at the end of the exercise. The observed effects, associated with a significant increase in blood lactate levels, were different in the two types of time estimation used in the present study. In experimental conditions in which participants had to evaluate duration of the time interval by mental counting, at the end of exercise a significant reduction in the overestimation of time made at rest was observed. On the other hand, when participants had to assess the difference in duration between two events without the possibility to mentally count, at the end of the exercise a significant deterioration in performance was observed. In both cases, no gender differences were seen.

With the growing demand for positioning services, angle-of-arrival (AoA) estimation or direction-finding (DF) has been widely investigated for applications in fifth-generation (5G) technologies. Many existing AoA estimation algorithms only require the measurement of the direction of the incident wave at the transmitter to obtain correct results. However, for most of the cellular systems such as Bluetooth indoor positioning system due to multipath and non-line-of-sight (NLOS) propagation, the indoor positioning accuracy is severely affected. In this paper a comprehensive algorithm is investigated that combines radio measurements from Bluetooth AoA local navigation systems with indoor position estimates obtained using particle filtering, which allows us to explore new optimised methods to reduce estimation errors in indoor positioning. First, particle filtering is used to predict the rough position of a moving target. Then, an algorithm with robust beam weighting is used to estimate the AoA of the multipath components. Based on this, a system of pseudo-linear equations for target positioning based on the probabilistic framework of PF and AoA measurement is derived. Theoretical analysis and simulation results show that the algorithm can improve the positioning accuracy by about 25.7% on average.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

A new design scheme is proposed for twisting the walls of a microchannel, and its performance is demonstrated numerically. The numerical study was carried out for a T-shaped microchannel with twist angles in the range of 0 to 34π. The Reynolds number range was 0.15 to 6. The T-shaped microchannel consists of two inlet branches and an outlet branch. The mixing performance was analyzed in terms of the degree of mixing and relative mixing cost. All numerical results show that the twisting scheme is an effective way to enhance the mixing in a T-shaped microchannel. The mixing enhancement is realized by the swirling of two fluids in the cross section and is more prominent as the Reynolds number decreases. The twist angle was optimized to maximize the DOM, which increases with the length of the outlet branch. The twist angle was also optimized in terms of the relative mixing. The two optimum twisting angles are generally not coincident. The optimum twist angle shows a dependence on the length of the outlet branch but it is not affected much by the Reynolds number.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Low-loss photonic waveguides in lithium niobate offer versatile functionality as nonlinear frequency converters, switches, and modulators for integrated optics. Combining the flexibility of laser processing with liquid phase epitaxy we have fabricated and characterized lithium niobate channel waveguides on lithium niobate and lithium tantalate. We used liquid phase epitaxy with K2O flux on laser-machined lithium niobate and lithium tantalate substrates. The laser-driven rapid-prototyping technique can be programmed to give machined features of various sizes, and liquid phase epitaxy produces high quality single-crystal, lithium niobate channels. The surface roughness of the lithium niobate channels on a lithium tantalate substrate was measured to be 90 nm. The lithium niobate channel waveguides exhibit propagation losses of 0.26 ± 0.04 dB/mm at a wavelength of 633 nm. Second harmonic generation at 980 nm was demonstrated using the channel waveguides, indicating that these waveguides retain their nonlinear optical properties.

The main objective of this work is the assessment of the annual number of hospital admissions for respiratory disease (HARD) due to the exposure to in-healable particulate matter (PM10), within the greater Athens area (GAA), Greece. Towards this aim, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) recorded in six monitoring stations located in the GAA, for a 13-year period 2001-2013, is used. Initially, a descriptive statistical treatment of PM10 concentrations took place. Furthermore, the AirQ2.2.3 software developed by the WHO was used to evaluate adverse health effects by PM10 in the GAA during the examined period. The results show that, during the examined period PM10 concentrations present a significant decreasing trend. Also, the mean annual HARD cases per 100,000 inhabitants ranged between 20 (suburban location) and 40 (city centre location). Approximately 70% of the annual HARD cases are due to city centre residents. In all examined locations, a declining trend in the annual number of HARD cases is appeared. Moreover, a strong relation between the annual number of HARD cases and the annual number of days exceeding the European Union daily PM10 threshold value was found.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

In this study, a novel method is proposed to estimate surface-spectral reflectance from camera responses that combines model-based and training-based approaches. An imaging system is modeled using the spectral sensitivity functions of an RGB camera, spectral power distributions of multiple light sources, unknown surface-spectral reflectance, additive noise, and a gain parameter. The estimation procedure comprises two main stages: (1) selecting the local optimal reflectance dataset from a reflectance database and (2) determining the best estimate by applying a neural network to the local optimal dataset only. In stage (1), the camera responses are predicted for the respective reflectances in the database, and the optimal candidates are selected in the order of lowest prediction error. In stage (2), most reflectance training data are obtained by a convex linear combination of local optimal data using weighting coefficients based on random numbers. A feed-forward neural network with one hidden layer is used to map the observation space onto the spectral reflectance space. In addition, the reflectance estimation is repeated by generating multiple sets of random numbers, and the median of a set of estimated reflectances is determined as the final estimate of the reflectance. Experimental results show that the estimation accuracies exceed those of other methods.

PIEZO channels PIEZO1 and PIEZO2 are the newly identified mechanosensitive, non-selective cation channels permeable to Ca2+. In higher vertebrates, PIEZO1 expresses ubiquitously in most of the tissues and cells while PIEZO2 expresses more specifically in the peripheral sensory neurons. PIEZO channels contribute to a wide range of biological behaviors and developmental processes, therefore driving a significant attention in the effort to understand their molecular properties. One prominent property of PIEZO channels is their rapid inactivation, which manifests itself as a decrease of channel open probability in the presence of a sustained mechanical stimulus. Lack of the PIEZO channel inactivation is linked to various mechanopathologies emphasizing the significance of studying this PIEZO channel property and the factors affecting it. In the present review, we discuss the mechanisms underlying the PIEZO channel inactivation, its modulation by interaction of the channels with lipids and/or proteins, and how the changes of PIEZO inactivation by the channel mutations can cause a variety of diseases in animals and humans.

In response to the issues of sensor noise and accumulated motion errors that lead to low positioning accuracy and insufficient robustness during large maneuvers or continuous flight of small unmanned aerial vehicles (UAVs) in complex environments, this paper proposes a multi-source and multimodal data fusion method. Initially, it employs a multimodal data fusion of various sensors including GPS (Global Positioning System), IMU (Inertial Measurement Unit), and visual sensors to complement the strengths and weaknesses of each hardware component, thereby eliminating motion errors to enhance accuracy. To mitigate the impact of sudden changes in sensor data, the method introduces a digital twin UAV data source. By utilizing the Extended Kalman Filter algorithm, it fuses data from both the real UAV and its digital twin, and the filtered positional information is fed back into the control system of the real UAV. This enables real-time correction of UAV positional deviations caused by sensor noise and environmental disturbances. The multi-source multimodal fusion Kalman filter method proposed in this paper significantly improves the positioning accuracy of UAVs in complex scenarios and the overall stability of the system. This method holds significant value in maintaining high-precision positioning in variable environments and has important practical implications for enhancing UAV navigation and application efficiency.

Quadruped robots possess significant mobility in complex and uneven terrains due to their outstanding stability and flexibility, making them highly suitable in rescue missions, environmental monitoring, and smart agriculture. With the increasing use of quadruped robots in more demanding scenarios, ensuring accurate and stable state estimation in complex environments has become particularly important. Existing state estimation algorithms relying on multi-sensor fusion, such as those using IMU, LiDAR, and visual data, often face challenges on non-stationary terrains due to issues like foot-end slippage or unstable contact, leading to significant state drift. To tackle this problem, this paper introduces a state estimation algorithm that integrates an Invariant Extended Kalman Filter (InEKF) with a disturbance observer, aiming at estimating the motion state of quadruped robots on non-stationary terrains. Firstly, foot-end slippage is modeled as a deviation in body velocity and explicitly included in the state equations, allowing for a more precise representation of how slippage affects the state. Secondly, the state update process integrates both foot-end velocity and position observations to improve the overall accuracy and comprehensiveness of the estimation. Lastly, a foot-end contact probability model, coupled with an adaptive covariance adjustment strategy, is employed to dynamically modulate the influence of the observations. These enhancements significantly improve the filter's robustness and the accuracy of state estimation in non-stationary terrain scenarios. Experiments conducted with the Jueying Mini quadruped robot on various non-stationary terrains show that the enhanced InEKF method offers notable advantages over traditional filters in compensating for foot-end slippage and adapting to different terrains.

In the context of smart agriculture, accurately estimating plant leaf chemical parameters is crucial for optimizing crop management and improving agricultural yield. Hyperspectral imaging, with its ability to capture detailed spectral information across various wavelengths, has emerged as a powerful tool in this regard. However, the complex and high-dimensional nature of hyperspectral data poses significant challenges in extracting meaningful features for precise estimation. To address this challenge, this study proposes an end-to-end estimation network for multiple chemical parameters of Astragalus leaves based on attention mechanism (AM) and multivariate hyperspectral features (AM-MHENet). We leveraging HybridSN and multilayer perception (MLP) to extract prominent features from the hyperspectral data of Astragalus membranaceus var. mongholicus (AMM) leaves and stems, as well as the surface and deep soil surrounding AMM roots. This methodology allows us to capture the most significant characteristics present in these hyperspectral data with high precision. The AM is subsequently used to assign weights and integrate the hyperspectral features extracted from different parts of the AMM. The MLP is then employed to simultaneously estimate the chlorophyll content (CC) and nitrogen content (NC) of AMM leaves. Compared with estimation networks that utilize only hyperspectral data from AMM leaves as input, our proposed end-to-end AM-MHENet demonstrates superior estimation performance. Specifically, AM-MHENet achieves an R2 of 0.983 with an RMSE of 0.73 for the estimation of CC in AMM leaves. For NC estimation, AM-MHENet achieves an R2 value of 0.977 with an RMSE of 0.27. These results underscore AM-MHENet’s effectiveness in significantly enhancing the accuracy of both CC and NC estimation in AMM leaves. Moreover, these findings indirectly suggest a strong correlation between the development of AMM leaves and stems, as well as the surface and deep soil surrounding the roots of AMM, and directly highlight the ability of AM to effectively focus on the relevant spectral features within the hyperspectral data. This findings from this study could offer valuable insights into the simultaneous estimation of multiple chemical parameters in plants, thereby making a contribution to the existing body of research in this field.

In recent years, the proliferation of digital communication systems has been fueled by the increasing use of connected devices in both consumer and industrial sectors. The predominant reliance on radio frequency communication for data transfer faces challenges due to physical limitations and regulatory restrictions on frequency ranges. Responding to these challenges, Visible Light Communication (VLC) has emerged as an innovative solution, utilising the visible light spectrum to modulate the intensity of light emitted by sources like white LEDs. This paper explores the feasibility of employing Red/Green/Blue (RGB) LEDs for three-dimensional visible light communications using off-the-shelves equipment. This type of communication is known as Wavelength Division Multiplexing (WDM) as data is encoded in the three colour wavelength. On-Off Keying (OOK) is used as modulation on each wavelength. Afterwards, the more efficient Orthogonal Frequency Division Multiplexing (OFDM) modulation scheme is explored. The implemented solution involves three emission circuits, each modulating the one colour component of the RGB LED current. The reception's side involves dichroic R/G/B colour filters and a Transimpedance Amplifier (TIA) circuit, with a Raspberry Pi 4 facilitating offline data decoding sampled by an Arduino UNO. The prototype demonstrates successful VLC communication with OOK modulation at distances up to 1.5m for red and blue LEDs and 0.75m for green LEDs, achieving data rates up to 800 bit/s.

Recently, attention mechanisms have developed into an important tool for performance improvement of deep neural networks. In computer vision, attention mechanisms are generally divided into two main branches: spatial and channel attention. Both attention categories have their own advantages. The fusion of both attentions achieves higher performance, on the cost of the computational load. This paper introduces an innovative and lighter n-shifted sigmoid channel and spatial attention (CSA) module to reduce the computational cost and to improve the 3D scene relevant features selection. To validate the proposed attention module, 3D scene object detection in the deep Hough voting point sets is considered as the testing application. The proposed attention module with its piecewise n-shifted sigmoid activation function improves the network’s learning and generalization capacity which effectively predict bounding box parameters directly from 3D scenes and detect objects more accurately. This advantage is achieved by selectively attending to more relevant features of the input data. When used in the deep Hough voting point sets, the proposed attention module outperforms state-of-the-art 3D detection methods on the sizable SUNRGBD dataset. Experiments conducted showed an increase of 12.02 mean accuracy precision (mAP) when compared to the celebrated VoteNet (without attention). It also got 9.92 mAP higher compared to the MLVCNet, and 10.32 mAP higher than the Point Transformer. The proposed model not only decreases the sigmoid vanishing gradient problem but also brings out valuable features by fusing channel-wise and spatial information while improving accuracy results in 3D object detection.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

We propose a deep-learning approach for the joint MIMO detection and channel decoding problem. Conventional MIMO receivers adopt a model-based approach for MIMO detection and channel decoding in linear or iterative manners. However, due to the complex MIMO signal model, the optimal solution to the joint MIMO detection and channel decoding problem (i.e., the maximum likelihood decoding of the transmitted codewords from the received MIMO signals) is computationally infeasible. As a practical measure, the current model-based MIMO receivers all use suboptimal MIMO decoding methods with affordable computational complexities. This work applies the latest advances in deep learning for the design of MIMO receivers. In particular, we leverage deep neural networks (DNN) with supervised training to solve the joint MIMO detection and channel decoding problem. We show that DNN can be trained to give much better decoding performance than conventional MIMO receivers do. Our simulations show that a DNN implementation consisting of seven hidden layers can outperform conventional model-based linear or iterative receivers. This performance improvement points to a new direction for future MIMO receiver design.

Introduction: Hypertension is a serious public health problem in Morocco. The objective of this pilot study was to estimate the salt intake of Moroccan adults by measuring 24-hour urinary sodium excretion. Methods: 132 participants were recruited from the central region of Morocco. Sodium, potassium and creatinine levels were measured using the 24-hour urine samples. Additional data included anthropometric measurements and socio-demographic questionnaire. Results: The daily sodium, potassium and creatinine excretions were 2779.1±1334.9 mg, 1350.0±642.8 mg and 820.3 ± 381.2 mg, respectively. Data analysis revealed that 71.2% of the participants had a daily sodium intake more than 2000 mg (5g of salt) recommended by the WHO. The mean of potassium excretion was 1350.0±642.8 mg /day, this average was lower than 3.51g per day recommended by the WHO. Conclusion: Public health measures to reduce sodium and increase potassium consumption in order to decrease the population’s risk of high blood pressure and heart disease are recommended.

Remote sensing datasets are increasingly being used to provide spatially explicit large scale evapotranspiration (ET) estimates. The focus of this study was to estimate and thematically map on a pixel-by-pixel basis, the actual evapotranspiration (ET_a) of the Wonji Shoa Sugarcane Estate using the Surface Energy Balance Algorithm for Land (SEBAL), Simplified Surface Energy Balance (SSEB) and Operational Simplified Surface Energy Balance (SSEBop) algorithms. The results obtained revealed that the ranges of the daily ETa estimated on January 25, February 26, September 06 and October 08, 2002 using SEBAL were 0.0 - 6.85, 0.0 – 9.36, 0.0 – 3.61, 0.0 – 6.83 mm/day; using SSEB 0.0 - 6.78, 0.0 – 7.81, 0.0 – 3.65, 0.0 – 6.46 mm/day, and SSEBop were 0.05 - 8.25, 0.0 – 8.82, 0.2 – 4.0, 0.0 – 7.40 mm/day, respectively. The Root Mean Square Error (RMSE) values between SSEB and SEBAL, SSEBop and SEBAL, and SSEB and SSEBop were 0.548, 0.548, and 0.99 for January 25, 2002; 0.739, 0.753, and 0.994 for February 26, 2002;0.847, 0.846, and 0.999 for September 06, 2002; 0.573, 0.573, and 1.00 for October 08, 2002, respectively. The standard deviation of ET_a over the sugarcane estate showed high spatio-temporal variability perhaps due to soil moisture variability and surface cover. The three algorithm results showed that well watered sugarcane fields in the mid-season growing stage of the crop had higher ET_a values compared with the other dry agricultural fields confirming that they consumptively use more water. Generally during the dry season, ET_a is limited to water surplus areas only and in wet season, ET_a was high throughout the entire sugarcane estate. The evaporation fraction (ETrF) results also followed the same pattern as the daily ET_a over the sugarcane estate. The total crop and irrigation water requirement and effective rainfall estimated using the Cropwat model were 2468.8, 2061.6 and 423.8 mm/yr for January 2001 planted and 2281.9, 1851.0 and 437.8 mm/yr for March 2001 planted sugarcanes, respectively. The mean annual ET_a estimated for the whole estate were 107 Mm³, 140 Mm³, and 178 Mm³ using SEBAL, SSEB, and SSEBop, respectively. Even though the algorithms should be validated through field observation, they have potential to be used for effective estimation of ET in the sugarcane estate.

— An extreme bandgap Al0.64Ga0.36N quantum channel HEMT with Al0.87Ga0.13N top and back barriers grown by MOCVD over bulk AlN substrate demonstrated a critical breakdown field of 11.37 MV/cm, higher than 9.8 MV/cm expected for the channel Al0.64Ga0.36N material. We show that the fraction of this increase is due to the quantization of the 2D electron gas. The polarization field maintains electron quantization in the quantum channel even at low sheet densities in contrast to conventional HEMT designs. An additional increase in the breakdown field is due to quantum-enabled real space transfer of energetic electrons into high-Al barrier layers in high electric fields. These results show the advantages of quantum channel design for achieving record high breakdown voltages and enabling superior power HEMT devices.

The combination of neural network and beamforming has been proved to be very effective in multi-channel speech separation. But its performance faces a challenge in complex environment. In this paper, an iteratively refined multi-channel speech separation method is proposed for the challenge, where the proposed is composed of initial separation and iterative separation. In initial separation, the time-frequency domain dual-path recurrent neural network neural network (TFDPRNN), minimum variance distortionless response (MVDR) beamformer and post-separation (also TFDPRNN) are cascaded for obtaining the first additional input in iterative separation. In iterative separation, the MVDR beamformer and post-separation are iteratively used, where the output of the MVDR beamformer is used as an additional input of the post-separation network and the final output comes from post-separation module. This iteration of the beamformer and post-separation is fully employed for promoting their individual optimization, which ultimately improves the overall performance of speech separation in multi-speaker scenarios. Experiments on the spatialized version of the WSJ0-2mix corpus show that our proposed method is significantly better than the current popular methods. In addition, the method also has a good effect on the dereverberation task.

Network Simulators (NS) is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. This is the case of Mobile Ad hoc Networks (MANETs) which can be extensively used in emergency situations or to gather information without infraestructure. An important factor to get realiable results in the MANETs’ simulations is the wireless channel module of NSs. In this report, we explain how thw wireless channel is implemented in NS-3 and it can be configured.

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

Polysulfides are endogenously produced in mammals and generally associated with protective functions. Our aim was to investigate the effect of dimethyl trisulfide (DMTS) in a mouse model of acute stress. DMTS activates transient receptor potential ankyrin 1 (TRPA1) channels and leads to neuropeptide release, potentially that of substance P (SP). We hypothesize that DMTS might inhibit the degrading enzymes of endocannabinoids, so this system was also investigated as another possible pathway for mediating the effects of DMTS. Trpa1 gene wild type (WT) and knock out (KO) mice were used to confirm the role of the TRPA1 ion channel in mediating the effects of DMTS. C57BL/6J, NK1 gene KO, and Tac1 gene KO mice were used to evaluate the effect of DMTS on the release and expression of SP. Some C57BL/6J animals were treated with AM251, an inhibitor of the cannabinoid CB1 receptor, to elucidate the role of the endocannabinoid system in these processes. Open field test (OFT) and forced swim test (FST) were performed in each mouse strain. Tail suspension test (TST) was performed in TRPA1 WT and KO animals. C-FOS immunohistochemistry was carried out on TRPA1 WT animals. DMTS treatment increased the number of highly active periods and decreased immobility time in the FST in WT animals, but had no effect on Trpa1 KO mice. DMTS administration induced neuronal activation in stress-related brain areas such as the locus coeruleus, dorsal raphe nucleus, lateral septum, paraventricular nucleus of the thalamus, and paraventricular nucleus of the hypothalamus. DMTS may have a potential role in the regulation of stress-related processes, and the TRPA1 ion channel may also be involved in mediating the effects of DMTS. DMTS can be an ideal candidate for further study as a potential remedy in stress-related disorders.

With the progression of AI, embedding advanced AI technologies into small robotics and mobile devices has become essential, driving research towards lightweighting AI models. Our study enhances the EPINET depth estimation model for light field images, aiming for compactness and faster inference while preserving accuracy. We conducted two-step experiments aimed at enhancing inference efficiency: Initially, by adjusting input streams and convolution layers, we simplified the CNN model, achieving faster inference times at the cost of reduced accuracy. To address this reduction in accuracy, we then applied knowledge distillation, allowing the simplified model to learn from the original model’s more complex patterns. In our quantitative experiments using two error metrics, MSE (Mean Squared Error) and BadPix, we identified optimal knowledge positions and evaluated the required complexity for the student model. As a result, our method improved MSE by 21% and BadPix by 14% compared to training without it. Furthermore, the student model achieved an inference speed 13% faster than the teacher model and surpassed its accuracy by 10% in MSE. Additionally, we demonstrated that repeatedly applying our approach could further enhance both model compactness and accuracy.

Automatic and blind parameter estimation based on the inherent features of wireless signals is a major research area due to the fact that these techniques lead to the simplification of receivers, especially in terms of coarse synchronization, more importantly reduce down the signaling load at the control channels. Thus, in the literature many techniques are proposed to estimate a vast set of parameters including modulation types and orders, data and chip rates, phase and frequency offsets and so on. In this paper, a cyclostationary feature detection based method is proposed to estimate the carrier numbers and carrier spacing of carrier-aggregated direct sequence spread spectrum cellular signals blindly. The particular chip rate of the signal is also estimated through the process jointly. In the paper, after the proposed method is formulated, the measurement setup which is developed to collect the data for the validation of the proposed method is introduced. The measurement results are post-processed for performance analysis purposes. To that end, the method is investigated in terms of SNR values, different channel conditions, and measurement durations. Furthermore, the performance of the proposed method is compared with that of energy detection. Measurement results indicate superior performance of the proposed method under significant wireless channel impairments and in low-SNR regions.

Information theoretic quantities such as entropy, entropy rate, information gain, and relative entropy are often used to understand the performance of intelligent agents in learning applications. Mean squared error has not played a role in these analyses, primarily because it is not felt to be a viable performance indicator in these scenarios. We build on a new quantity, the log ratio of entropy powers, to establish that minimum mean squared error (MMSE) estimation, prediction, and smoothing are directly connected to Mutual Information Gain or Loss in an agent learning system modeled by a Markov chain for many probability distributions of interest. Expressions for mutual information gain or loss are developed for MMSE estimation, prediction, and smoothing and an example for fixed lag smoothing is presented.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

The Inverted F Antenna (IFA) with the parasitic element on a finite conducting plane is proposed in the range frequency of 0.1 to 5.5 GHz and its characteristics are analyzed numerically. In this research, the parasitic element and the main IFA are investigated to obtain the resonance frequency for multiband operation purposes. The parasitic element is placed beneath adjusted to the main IFA to derive more frequency bands. The distance between the parasitic element and main horizontal element extremely affects the performance of the IFA. It is found that when the parasitic element is located closer to the conducting plane, this element is coupled by the current on the conducting plane. Consequently, the return loss bandwidth becomes narrower. Therefore, the gain of the proposed IFA becomes a bit higher. The antenna gain is about 8.21 dB at band #3 (λ_1.747), 7.43 dB at band #5 (λ_2.967) and 8.82 dB at band #6 (λ_4.023). This occurs when the calculation condition is antenna height h1 = 23 mm, h2 = 21 mm, horizontal antenna elements L = 173.2 mm, L1 = 140.9 mm and Lp = 152 mm, shorted element Ls = 30.7 mm, the distance between parasitic element and shorted element pyl = 5 mm. While the size of conducting plane is considered pxp+pxm by pyp+pym as 57.5+57.5 mm by 200+50 mm. In the numerical analysis, the electromagnetic simulator WIPL-D based on Method of Moment is used. The results show that the proposed IFA has UHF and SHF channel receiver which are suitable for advanced wireless service (band #3), mobile phones, Bluetooth, maritime service, radiolocation service (band #5) and radars, mobile phones, commercial wireless LAN (band #6).

This interdisciplinary investigation of the human remains of Balduin Helm, one of the most important abbots of Fürstenfeld monastery, provides novel information on that historic individual. This is particularly interesting since Balduin, during early 18th century, was involved in the renovation of this large Bavarian monastery. Metastatic prostate cancer was found as evidenced by multiple mixed osteolytic-osteoblastic bone lesions in all available vertebral bodies, fragments of both hemipelvises and isolated metastases in skull bones. Distribution, radio- and histomorphology, and especially the immunohistochemical detection of prostate-specific antigen in those metastases, definitively confirm this diagnosis. Further investigation, especially by stable isotope analysis, showed a balanced high-level diet with considerable contribution from animal protein and significant freshwater fish. These additional findings suggest a significant radiocarbon reservoir effect as an explanation for a “too old” radiocarbon dating. Finally, the obviously high-level protein diet may have contributed to the tumorigenesis which caused the death of the abbot at an advanced age.

Accurate forecasting of crop yields holds paramount importance in guiding decision-making processes related to breeding efforts. This study focused on the application of multi-sensor data fusion and machine learning algorithms based on unmanned aerial vehicles (UAVs) in wheat yield prediction. Five machine learning (ML) algorithms namely random forest (RF), partial least squares (PLS), ridge regression (RR), K-Nearest Neighbor (KNN) and eXtreme Gradient Boosting Decision Tree (XGboost) were utilized for multi-sensor data fusion, and three ensemble methods including the second-level ensemble methods (stacking and feature-weighted) and the third-level ensemble method (simple average) for wheat yield prediction. The 270 wheat hybrids were used as planting materials under full and limited irrigation treatments. A cost-effective multi-sensor UAV platform, equipped with red–green–blue (RGB), multispectral (MS), and thermal infrared (TIR) sensors, was utilized to gather remote sensing data. The results revealed that the XGboost algorithm exhibited outstanding performance in multi-sensor data fusion, with the RGB+MS+Texture+TIR combination demonstrating the highest fusion performance (R2=0.660, RMSE= 0.754). Compared with the single ML model, the employment of three ensemble methods significantly enhanced the prediction accuracy of wheat yield. Notably, the third-layer simple average ensemble method demonstrated superior performance (R2 = 0.733, RMSE= 0.668 t ha-1). It significantly outperformed both the second-layer ensemble methods of Stacking (R2= 0.668, RMSE= 0.673 t ha-1) and feature-weighted (R2= 0.667, RMSE= 0.674 t ha-1), thereby exhibiting superior predictive capabilities. This finding demonstrated that the third-layer ensemble method not only augments the predictive ability of the model but also fine-tuned the accuracy of wheat yield prediction through the employment of simple average ensemble learning. Consequently, it offers a novel perspective for crop yield prediction and breeding selection.

Ion channels serve many cellular functions including ion homeostasis, volume regulation, signaling, nutrient acquisition, and developmental progression. Although the complex lifecycles of malaria parasites necessitate ion and solute flux across membranes, whole genome sequencing of the human pathogen, Plasmodium falciparum, revealed remarkably few orthologs of known ion channel genes. Contrasting with this, biochemical studies have implicated channel-mediated flux of ions and nutritive solutes across several membranes in infected erythrocytes. Here, I review advances in the cellular and molecular biology of ion channels in malaria parasites. These studies have implicated novel parasite genes in the formation of at least two ion channels, with additional ion channels likely present at various membranes and parasite stages. Computational approaches that rely on homology to known channel genes from higher organisms will not be very helpful in identifying the molecular determinants of these activities. Given their unusual properties, novel molecular and structural features, and essential roles in pathogen survival and development, parasite channels should be promising targets for therapy development.

In this paper, we develop a tractable mathematical model and emulation framework for communicating information through water using acoustic signals. Water is considered as one of the most complex mediums to model owing to its vastness and variety in characteristics depending on the scenario, what kind of water-body (lakes, rivers, tanks, sea etc.) and geographical location of the water-body is considered. Our proposed mathematical model involves the concept of damped harmonic oscillators to represent the medium (water) and Milne’s oscillator technique to map the interaction between the acoustic signal and water. Wave equations formulated for acoustic pressure and acoustic wave velocity are used to characterize the travelling acoustic signal. Signal strength, phase shift and time-delay generated from the mathematical model are fed to a Simulink-based emulator framework to generate channel samples and channel impulse responses. The emulator uses wide sense stationary uncorrelated scattering (WSSUS) assumption and finite sum-of-sinusoids (SOS) with uniformly distributed phase to generate the channel samples. Using the emulator platform it is possible to generate amplitude variation profile, Doppler shift and spread experienced by any travelling signal through different underwater communication scenarios. Such an emulator platform can be used to simulate different communication scenarios, underwater network topologies, data to train different learning models and predict performance of different modulation, multiplexing, error correction and multi-access techniques for underwater acoustic communications (UWAC) systems.

in this paper, the optical channel performance with respect to varying scintillation index parameters is studied. Where different channel effects are studied and analyzed. In free-space optical (FSO) communication, the major drawback of the optical communication system is the atmospheric turbulence (AT). This effect is nonlinear with optical channel altitude being changed. Therefore, the power margenal (PM) required for such a channel is also inconstant respectively. In this thesis, we analyze AT effect on the optical channel with different altitudes. Such that we found the difference in the range of PM required for such optical link distance. In our result, the Bit Error Rate (BER) VS. PM required is measured. The optical channel model is Log-Normal considered and the BER threshold BER^th = 10^-10 is taken.

In line with Pomeau’s conjecture about the relevance of directed percolation (DP) to turbulence onset/decay in wall-bounded flows, we propose a minimal stochastic model dedicated to the interpretation of the spatially intermittent regimes observed in channel flow before its return to laminar flow. Numerical simulations show that a regime with bands obliquely drifting in two stream-wise symmetrical directions bifurcates into an asymmetrical regime, before ultimately decaying to laminar flow. The model is expressed in terms of a probabilistic cellular automaton evolving von Neumann neighbourhoods with probabilities educed from a close examination of simulation results. It implements band propagation and the two main local processes: longitudinal splitting involving bands with the same orientation, and transversal splitting giving birth to a daughter band with orientation opposite to that of its mother. The ultimate decay stage observed to display one-dimensional DP properties in a two-dimensional geometry is interpreted as resulting from the irrelevance of lateral spreading in the single-orientation regime. The model also reproduces the bifurcation restoring the symmetry upon variation of the probability attached to transversal splitting, which opens the way to a study of the critical properties of that bifurcation, in analogy with thermodynamic phase transitions.

Ion channels contribute fundamental properties to all cell membranes. The ion channels are highly diverse in conductivity, structure, location and function. However, many of them can be regulated by common mechanisms, such as voltage or (de-)phosphorylation. Considering primarily pain-related ion channels, this review covers more novel and less known features of ion channel function, also with the aim to transfer knowledge between fields, which get inevitably more separate due to their size.

Security is a major topic in recent researchers, and finding new methods deliver was the motivations for this research to emphasize and as an awareness to browsers developers to handle images with more care and to enhance exploit detection technology in the browser, as this paper proves that hackers now can attack users with just an image.

Phα1β a spider peptide, purified from the venom of Phoneutria nigriventer inhibits high voltage calcium channels and is antagonist of TRPA1 receptor two important pain transduction path-ways. In the last 15 years, we have showed, in preclinical tests with Phα1β native and recombi-nant in rodent models of pain the potential of Phα1β to become a new analgesic drug. Evaluation of new drug on human ERG channel is requirement of the regulatory agencies. For the hERG channel inhibition assay it was used the commercial kit FLIPR® Potassium Assay. It was tested the effect of Phα1β and as positive control dofetilide, a well characterized hERG block-er. Phα1β 56, 225, 450 and 900 pMol caused at a higher concentration a very weak inhibition of the hERG channel activity of about 13.47 % with channel inhibition at 50%, IC50 > 900 pMol. Dofetilide (0.0001 - 10 µM), a known hERG inhibitor, caused a well-known, concentra-tion-dependent inhibition of the hERG channel with a mean IC50 of 0.1642 µM (0.1189 – 0.2282 µM. For the cytotoxicity assay, Phα1β concentrations of 56, 225, 450 and 900 pMol incubated for 24 h with HEK293-hERG cells did not alter the viability of the HEK293-hERG cells. It is con-cluded that Phα1β even at high concentrations does not interfere with hERG channels.

The cardiac sodium ion channel (NaV1.5) is a protein with four domains (DI-DIV), each with six transmembrane segments. Its opening and subsequent inactivation results in the brief rapid influx of Na+ ions resulting in the depolarization of cardiomyocytes. The neurotoxin veratridine (VTD) inhibits NaV1.5 inactivation resulting in longer channel opening times, and potentially fatal action potential prolongation. VTD is predicted to bind at the channel pore, but alternative binding sites have not been ruled out. To determine the binding site of VTD on NaV1.5, we performed docking calculations and high-throughput electrophysiology experiments. The docking calculations identified two distinct binding regions. The first site was in the pore, close to the binding site of NaV1.4 and NaV1.5 blocking drugs in experimental structures. The second site was at the “mouth” of the pore at the cytosolic side, partly solvent-exposed. Mutations at this site (L409, E417, and I1466) had large effects on VTD binding, while residues deeper in the pore had no effect, consistent with VTD binding at the mouth site. Overall, our results suggest a VTD binding site close to the cytoplasmic mouth of the channel pore. Binding at this alternative site might indicate an allosteric inactivation mechanism for VTD at NaV1.5.

The Fruit Harvest Helper, a mobile application developed by Northwest Nazarene University’s (NNU) Robotics Vision Lab, aims to assist farmers in estimating fruit yield for apple orchards. Currently, farmers manually estimate the fruit yield for an orchard, which is a laborious task. Fruit Harvest Helper seeks to simplify their process. While prior research efforts at NNU concentrated on developing an iOS app for blossom detection, this current research aims to adapt that smart farming application for apple detection across multiple platforms, iOS and Android. The old and new applications were designed with an intuitive user interface that is easy for farmers to use, allowing for quick image selection and processing. Unlike before, the adapted app utilizes a color ratio-based image segmentation algorithm implemented in OpenCV C++ to detect apples in apple tree images selected for processing. The results of testing the algorithm with a dataset of images indicate an 8.52% Mean Absolute Percentage Error (MAPE) and a Pearson correlation coefficient of 0.6 between detected and actual apples on the trees. These findings were obtained by evaluating the images from both the east and west sides of the trees, which was the best method to reduce the error of this algorithm. Although the Fruit Harvest Helper shows promise, there are many opportunities for improvement. These opportunities include exploring alternative machine-learning approaches for apple detection, conducting real-world testing without any human assistance, and expanding the app to detect various types of fruit. The Fruit Harvest Helper mobile application is among the many mobile applications contributing to precision agriculture, nearing readiness for farmers to use in yield monitoring and farm management.

Comparison between hydraulic and hydrologic computational methods is conducted in this study, regarding prismatic open channels under unsteady subcritical flow conditions. One-dimensional unsteady flow continuity and momentum equations are solved using explicit and implicit finite difference schemes for a symmetrical trapezoidal cross section, where the flow discharge and depth are the dependent variables. The results have been compared to those derived from Muskingum-Cunge hydraulic/hydrologic method as well as the commercial software HEC-RAS. The results from explicit and implicit code compare well to those from commercial software and hydraulic/hydrologic methods for long prismatic channels, thus directing the hydraulic engineer to quick preliminary design of prismatic open channels for unsteady flow with satisfactory accuracy.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

In this paper, we present a multi-task model that predicts disparities and confidence levels in deep stereo matching simultaneously. We do this by combining its successful model for each separate task and obtaining a multitask model that can be trained with a proposed loss function. We show the advantages of this model compared to training and predicting disparity and confidence sequentially. This method enables an improvement of 15% to 30% in the area under the curve (AUC) metric when trained parallel rather than sequential. In addition, the effect of weighting the components in the loss function on the stereo and confidence performance is investigated. By improving the confidence estimate, the practicality of stereo estimators for creating distance images is increased.

Wireless communication has proliferated due to the colossal augmentation of smart phones, mobile phones, tablets and laptops etc. Multimedia applications such as live videos, audios, still images, animated graphics and live communications all requires accompaniments of quality of service (QoS) as well as reliable end-to-end transfer of data. Information about the availability of resources in channel is must in order to improve the QoS. QoS can be determined in terms of capacity of channel, available bandwidth (ABW), and bulk transfer capacity (BTC). Bandwidth availability is a key check for improving the QoS in a network. The performance of a multimedia application is directly affected by the bandwidth availability. One of the most important QoS characteristic is ABW at a wireless route and it can be demarcated as least unused capacity of links instituting a network route. Since now there have been many bandwidth estimation techniques are available in the literature to increase the network performance. Bandwidth estimation techniques have been arranged into three leading classifications: i) Active probing bandwidth estimation techniques, ii) Passive bandwidth estimation technique and iii) Model based bandwidth estimation techniques. Each of these techniques are briefly discussed in this paper.

For voltage-gated Ca2+ channel (VGCC), its α2δ subunits are traditionally considered to be auxiliary subunits that regulates VGCC trafficking to the plasma membrane. The antiepileptic, antinociceptive and anxiolytic gabapentin (GBP) has previously been shown to bind the VGCC α2δ subunits with high affinity to disrupt VGCC trafficking. Yet, the interaction between GBP and α2δ still remains poorly understood from a structural point of view. For instance, it is not clear yet what the structural implication is of α2δ-1-bound GBP against VGCC trafficking. With a set of experimental data-driven structural analysis of the VGCC α2δ-1 and its ligand GBP, this article postulates for the first time that: 1), α2δ-1 bound GBP stabilizes the α2δ-1-GBP complex structure; 2), α2δ-1 bound GBP restrains the conformational flexibility of α2δ-1; 3), α2δ-1-bound GBP establishes an electrostatic axis consisting of Q535 (Gln535)-R241 (Arg241)-GBP (gabapentin)-D452 (Asp452), which constitutes an energetically favourable contribution towards the structural stability of the α2δ-1-GBP complex and helps restrains the conformational flexibility and local structural rigidification of α2δ-1; and 4), GBP-induced local conformational inflexibility and structural rigidification of α2δ-1 is one key step in the pharmacological disruption of VGCC trafficking by GBP.

YouTube Kids serves as a dynamic and user-friendly resource for young learners to learn English. Its extensive library of instructional materials, which includes captivating animations and interactive movies, provides a rich and varied learning environment. Through the integration of play and exploration into language study, YouTube Kids creates a comfortable and engaging atmosphere that allows kids to improve their English language skills at their own pace. In this research article, a narrative literature review was employed as a qualitative methodology. Based on the gathered relevant literature, YouTube Kids presented such positive and negative impacts as a channel for English language acquisition. YouTube Kids is indeed a beneficial tool for young learners who are trying to learn English, but at the same time, it does have some potential disadvantages, as some videos may not employ the same standard or correctness of English, which could expose kids to improper grammar or pronunciation. Parents and teachers need to carefully select and keep an eye on the content their kids watch to ensure that their children's YouTube Kids content supports their language learning objectives. Through careful supervision and curation, parents and educators may maximize the usefulness of the site as a medium for teaching young learners English language skills while also minimizing any potential downsides.

In the last decade, three-dimensional (3D) printing has allowed the field of complex microfluidic channels to expand rapidly towards channels with variable cross-sections (i.e., beyond simple rounded media with a constant diameter) and channels. Whose trajectory can be outside a single plane and has gained numerous macro- and nanoscale manufacturing advances. Three-dimensional printing is being explored for various biomedical applications and the fabrication of nanomedicines using additive manufacturing techniques. Employing 3D-printed templates for macro-to-micro interfacing, a passively operated microfluidic device was designed. The research seeks to fabricate a biodevice that enables insulin microdosing, creating a subsystem like a microvalve and a microchannel matrix using additive manufacturing techniques. Our systems feature designs that enhance fluid dynamics without affecting the stability of the insulin. We propose using Humalog insulin in tropical climates (up to 30°C) without refrigeration for 28 days. The microvalve has a spiral trajectory with four outlet channels distributed along it. These channels align with the microchannels organized in a 10 mm x 15 mm matrix with 25 microchannels, each with a 770 µm internal diameter. The system delivers a dose of 2,3 mL in 6 minutes. We designed these systems for insulin micro-dosing, but they can also serve similar devices for other drugs.

Zn2+ has been implicated in the regulation of intestinal redox and microbial homeostasis, and we recently reported that transient receptor potential canonical (TRPC) 6 channel activity contributes to intracellular Zn2+ homeostasis in mammalian cells. This study aims to investigate the role of TRPC6-mediated Zn2+ influx in stress resistance of intestine. Expression profile of TRPC1-C7 mRNAs in the actively inflamed mucosa from inflammatory bowel disease (IBD) patients was analyzed using GEO database. Systemic TRPC3-knockout (KO) and TRPC6-KO mice were treated with dextran sulphate sodium (DSS) to induce colitis. The Zn2+ concentration and the mRNA expression levels of oxidative/inflammatory markers in colon tissues were quantitatively analyzed, and gut microbiota profiles were compared. TRPC6 mRNA expression level was increased in IBD patients and DSS-treated mouse colon tissues. DSS-treated TRPC6-KO mice, but not TRPC3-KO mice, showed severe weight loss and increased disease activity index compared with DSS-treated WT mice. The mRNA abundances of antioxidant proteins were basically increased in TRPC6-KO colon, with changes in gut microbiota profiles. Treatment with TRPC6 activator prevented the DSS-induced colitis progression accompanied by increasing Zn2+ concentration. We suggest that TRPC6-mediated Zn2+ influx activity plays a key role in stress resistance against IBD, providing a new strategy for treating colitis.

Transient Receptor Potential Vanilloid 4 (TRPV4) channel is a non-selective cation channel, mostly permeable to calcium (Ca2+), which participates to intracellular Ca2+ handling in cardiac cells. It is widely expressed through the body and is activated by a large spectrum of physico-chemical stimuli, conferring it a role in a variety of sensorial and physiological functions. With-in the cardiovascular system, TRPV4 expression was reported in cardiomyocytes, endothelial cells (ECs) and smooth muscle cells (SMCs) where it modulates mitochondrial activity, Ca2+ ho-meostasis, cardiomyocytes electrical activity and contractility, cardiac embryonic development, fibroblast proliferation but also vascular permeability, dilatation and constriction. On the other hand, TRPV4 channels participate in several cardiac pathological processes such as development of cardiac fibrosis, hypertrophy, ischemia-reperfusion injuries, heart failure, myocardial infarc-tion, and arrhythmia. In this manuscript, we provide an overview of TRPV4 channel implica-tions in cardiac physiology and discuss the potential of TRPV4 channel as therapeutic target against cardiovascular diseases.

Next generation in-to-out-of body biomedical applications have adopted optical wireless communications (OWCs). However, by delving into the published literature, a gap is recognised in modeling the in-to-out-of channel, since most published contributions neglect the particularities of different type of tissues. Towards this direction, in this paper we present a novel pathloss and scattering models for in-to-out-of OWC links. Specifically, we derive extract analytical expressions that accurately describe the absorption of the five main tissues’ constituents, namely fat, water, melanin, oxygenated and de-oxygenated blood. Moreover, we formulate a model for the calculation of the absorption coefficient of any generic biological tissue. Next, by incorporating the impact of scattering in the aforementioned model we formulate the complete pathloss model. The developed theoretical framework is verified by means of comparisons between the estimated pathloss and experimental measurements from independent research works. Finally, we illustrate the accuracy of the theoretical framework in estimating the optical properties of any generic tissue based on its constitution. The extracted channel model is capable of boosting the design of optimized communication protocols for a plethora of biomedical applications.

The Casiquiare River is a natural channel that connects two of the greatest rivers in the world, the Orinoco and the Amazon in the South American Continent. The aim of this paper is to present a review and synthesis of the hydrological and sedimentological knowledge of the Casiquiare River, including the first hydro-sedimentary balance of the Casiquiare fluvial system conducted at the bifurcation and at the mouth on September 9-12, 2000, during the expedition ‘Humboldt-Amazonia 2000’. Bathymetric, flow discharge and physico-chemical measurements were made at the inlet and at the outlet of the Casiquiare Channel. The main conclusions of this study indicate that Casiquiare is taking a significant proportion of flow (20 to 30%) from the Upper Orinoco basin to the Amazon basin. Throughout its 356 km-course, this chameleon channel undergoes significant morphological, hydrological and bio-geochemical variations between the inlet and the outlet, whose most visible witnesses are the increase in its width (3 to 4 times), flow (7 to 9 times) and its change in water color (white to black water), under the influence of tributaries coming from vast forest plains.

The growing concerns about floods have highlighted the need for accurate and detailed precipitation data as extreme precipitation occurrences can lead to catastrophic floods, resulting in significant economic losses and casualties. Integrated Multi-satellitE Retrievals for the Global Precipitation Measurement (GPM-IMERG) is a commonly used high-resolution gridded precipitation dataset and is recognized as trustworthy alternative sources of precipitation data. The aim of this study is to comprehensively evaluate the performance of GPM IMERG Early (IMERG-E), Late (IMERG-L), and Run Final (IMERG-F) in precipitation estimation and their capability in detecting extreme rainfall indices over southwestern Iran during 2001-2020. The Asfezari gridded precipitation data which are developed using a dense of ground-based observation were utilized as the reference dataset. The findings indicate that the IMERG-F performs reasonably well in capturing many extreme precipitation events (defined by various indices). All the three products showed a better performance in capturing fixed and non-threshold precipitation indices across the study region. The findings also revealed that both IMERG-E and IMERG-L have problems in rainfall estimation over elevated areas showing values of overestimations. Examining the effect of land cover type on the accuracy of the precipitation products suggest that both IMERG-E and IMERG-L show large and highly unrealistic overestimations over inland water bodies and permanent wetlands. The results of the current study highlight the potential of IMERG-F as a valuable source of data for precipitation monitoring in the region.

The purpose of this paper is to propose a novel transfer learning regularization method based on knowledge distillation. Recently, transfer learning methods have been used in various fields. However, the problems such as knowledge loss still occur during the process of transfer learning to a new target dataset. To solve these problems, there are various regularization methods based on knowledge distillation techniques. In this paper, we propose a transfer learning regularization method based on feature map alignment used in the field of knowledge distillation. The proposed method is composed of two attention based submodules: self-pixel attention (SPA) and global channel attention (GCA). The self-pixel attention submodule utilizes both the feature maps of the source and target models, so that it provides an opportunity to jointly consider the features of the target and the knowledge of the source. The global channel attention submodule determines the importance of channels through all layers, unlike the existing methods that calculate these only within a single layer. Accordingly, transfer learning regularization is performed by considering both the internal of each single layer and the depth of the entire layer. Consequently, the proposed method using both of these submodules showed overall improved classification accuracy than the existing methods in classification experiments on commonly used dataset.

KV channel-interacting proteins (KChIPs) belong to a family of Ca2+-binding EF-hand proteins that are able to bind to the N-terminus of the KV4 channel α-subunits. As the auxiliary subunit, KChIPs are critically involved in regulating the amplitude and gating properties of KV4 channels by modulating their cell surface trafficking, voltage-dependent activation, inactivation kinetics, and recovery rate from inactivation. IKs, ICa,L, and INa can also be regulated by KChIPs. KChIPs are predominantly expressed in the brain and heart, where they contribute to the maintenance of the excitability of neurons and cardiomyocytes by modulating the KV4 currents. Interestingly, all KChIPs can act as transcription factors to control the expression of genes involved in pain, memory, and circadian regulation. Altered expression of KChIPs has been implicated in the pathogenesis of many diseases, such as arrhythmia, heart failure, Alzheimer's disease, etc. In this review, we summarize the research progress of KChIPs in their structural properties, physiological functions, and pathological roles in disease progression, and provide an overview of the therapeutic potential of KChIPs as pharmacological targets for associated disorders.

After cut by basecutter, sugarcane stalks are carried to a chopper by the basecutter and the feeding/conveying rollers train of harvester. However, the conventional feeding/conveying channels of sugarcane chopper harvesters, when harvesting seriously lodged sugarcane, have numerous drawbacks, including easy clogging, and poor adaptability. In order to resolve these problems, a novel design and layout method of feeding/conveying and chopping channel are proposed in the paper. And a chopper centrally-mounted channel is designed for a sugarcane chopper harvester as well, which has been implemented in the HN4GDL-91 harvester. The proposed channel consists of a feeding/conveying rollers train, a chopper, and a billet conveying device. By mounting the chopper between the feeding/conveying rollers train and the billets conveying device, the harvester can avoid the chopper chopping back the billets, thus improving the harvest quality. The feeding/conveying rollers train is designed with only a pair of feeding rollers and a pair of conveying rollers, achieving a short channel path. Moreover, the structure of the basecutter and the mechanism carrying stalks to feeding rollers are studied via theoretical analysis and tests. The relationship between the basecutter and the chopper centrally-mounted channel is also conducted in systematic analysis. The results of the theoretical analysis show that the inclination angle of the disc of basecutter should be 2° greater than the angle of the feeding conveying channel (both angles are from the horizontal plane). The inclination angle of the disc of basecutter should go from 10° to 15°. A field experiment with four factors and three levels indicates that the field loss rate is 2.45%, the feed quantity is 16.66 kg/s, and the qualified rate of the billets is 98.02%, while the number of sugarcane stalks in a clump, the ground speed of harvester the rotational speed of the chopper, and the rotational speed of feeding/conveying roller are 10, 1.09 m/s, 390 r/min, and 230 r/min, respectively. It is concluded that the proposed chopper centrally-mounted channel could improve the conveying and harvesting performance significantly.

EMG analysis is becoming increasingly important in many research and clinical applications, including muscle fatigue detection, control of robotic mechanisms and prostheses, clinical diagnosis of neuromuscular diseases and quantification of force. However, electromyographic signals can be contaminated by various types of noise, interference and artifacts, which can lead to misinterpretation of the data acquired using this method. Even assuming best practices, the collected signal may still be altered by such contaminants. The aim of this paper is to review methods employed to reduce contamination of single channel EMG signals. This review is limited to methods performed directly on the measured EMG signal and those that allow total reconstruction of the EMG signal. Subtraction methods used in the time domain, denoising methods performed after signal decomposition and hybrid methods are assessed. It is defended that individual methods may be more or less suitable for a particular application depending on contaminant(s) present in the signal and on the specific requirements of the application.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

Eutrophication, a global concern, impacts water quality, ecosystems, and human health. It’s crucial to monitor algal blooms in freshwater reservoirs, as they indicate the trophic condition of a waterbody through Chlorophyll-a (Chla) concentration. Traditional monitoring methods, however, are expen-sive and time-consuming. Addressing this hindrance, we developed models using remotely sensed data from the Sentinel-2 satellite for large-scale coverage, including its bands and spectral indexes, to estimate the Chla concentration on 149 freshwater reservoirs in Ceará, Brazil. Several machine learning models were trained and tested, including k-nearest neighbours, random forests, extreme gradient boosting, the least absolute shrinkage, group method of data handling (GMDH), and sup-port vector machine models. A stepwise approach determined the best subset of input parameters. Using a 70/30 split for the training and testing datasets, the best-performing model was the GMDH, achieving an R2 of 0.91, MAPE of 102.34%, and RMSE of 20.38 g/L, which are values consistent with the ones found in the literature. Nevertheless, the predicted Chla concentration values were most sensitive to the red, green, and near infra-red bands.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

This work addresses the problem of automatic head pose estimation and its application in 3D gaze estimation using low quality RGB--D sensors without any subject cooperation or manual intervention. The previous works on 3D head pose estimation using RGB--D sensors require either an offline step for supervised learning or 3D head model construction which may require manual intervention or subject cooperation for complete head model reconstruction. In this paper, we propose a 3D pose estimator based on low quality depth data, which is not limited by any of the aforementioned steps. Instead, the proposed technique relies on modeling the subject's face in 3--D rather than the complete head, which in turn, relaxes all of the constraints with the previous works. The proposed method is robust, highly accurate and fully automatic. Moreover, it does not need any offline step. Unlike some of the previous works, the method only uses depth data for pose estimation. The experimental results on the Biwi head pose database confirm the efficiency of our algorithm in handling large pose variations and partial occlusion. We also evaluate the performance of our algorithm on IDIAP database for 3D head pose and eye gaze estimation.

Purpose: The purpose of this study was to evaluate the dosimetric impact of multiple channels compared to a single channel in high dose rate (HDR) vaginal cuff brachytherapy (VCBT). Methods and materials: Sample plans of HDR VCBT from both single and multiple channel cylinders at 2.5, 3.0 and 3.5 cm in diameter were created and analyzed. The doses were prescribed either at the 0.5 cm depth with 5.5 Gy for 4 fractions or at the cylinder surface with 8.8 Gy for 4 frac¬tions, in various treatment lengths ranging from 3 to 8 cm. A 0.5 cm ring target volume called PTV_Eval was contoured for each plan and served as the target volume for dosimetric evaluation. Mean doses and the doses covering 90% (D90), 10% (D10), and 5% (D5) of PTV_Eval were calculated and compared. The same treatment lengths, same prescription regimens, same target volume contouring and same plan evaluation methods were repeated for the similar size single channel and multiple channel cylinders. Results: The mean doses of both regimens with the multi-channel cases (6.3 to 7.1 Gy) were comparable to single channel ones (6.4 and 7.5 Gy). The ranges of D90, D10 and D5 were from 3.654 to 5.04 Gy, 8.44 to 10.08 Gy and 8.84 to 10.86 Gy in the multi-channel cases, but from 5.36 to 5.76 Gy, 7.40 to 9.97 Gy and 8.16 to 11.93 Gy in the single channel cases, respectively. Conclusion: The single channel and multiple-channel cylinder deliver a similar mean dose, but with marked heterogeneity in D90, D5 and D10 for the same prescription dose and target volume. Multi-channel cylinders adequately cover the target volume, but given the heterogeneity, increased treatment time and cost are best suited for asymmetric target volumes.

(1) Background: The Gárdos channel (KCNN4) and Piezo1 are the best-known ion channels in the red blood cell (RBC) membrane. Nevertheless, the quantitative electrophysiological behavior of RBCs and its heterogeneity are still not completely understood.; (2) Methods: Here we use state-of-the-art biochemical methods to probe for the abundance of the channels in RBCs. Furthermore, we utilize automated patch-clamp, based on planar chips, to compare the activity of the two channels in reticulocytes and mature RBCs. Besides this characterization, we performed membrane potential measurements to demonstrate the effect of channel activity and interplay on the RBC properties.; (3) Results: Both, Gárdos channel and Piezo1, albeit their average copy number of activatable channels per cell is in the single digit range, can be detected by transcriptome analysis of reticulocytes. Proteomics analysis of RBCs could only detect Piezo1 but not the Gárdos channel. Furthermore, they can be reliably measured in the whole-cell configuration of the patch-clamp method. While for the Gárdos channel the activity is higher in reticulocytes compared to mature RBCs, for Piezo1 the tendency is the opposite. While the interplay between Piezo1 and Gárdos channel cannot be followed using the patch-clamp measurements, it could be proved based on membrane potential measurements in populations of intact RBCs.; (4) Conclusions: We discuss the Gárdos channel and Piezo1 abundance, interdependencies and interactions in the context of their proposed physiological and pathophysiological functions, which are the passing of small constrictions, e.g., in the spleen, and their active participation in blood clot formation and thrombosis.

Forest ecosystems make a greater contribution to carbon (C) stocks than any other terrestrial ecosystem. To understand the role of regional forest ecosystems in global climate change and carbon exchange, forest C stock and its spatial distribution within the small (2,300 km2) Liuxihe River basin were analyzed to determine the different contributors to the C stock. Forest C stocks were quantified by measuring the biomass of trees, understory vegetation, litter and roots, as well as soil organic C, using data from field samples and laboratory experiments. The results showed that forests stored 38.04 Tg C in the entire basin, with secondary and planted forests accounting for 89.82% and 10.18%, respectively, of the stored C. Five types of forests, a subtropical evergreen broad-leaved forest, a subtropical coniferous and broad-leaved mixed forest, a subtropical coniferous forest, a timber forest, and a non-wood forest, stored 257.55 ± 15.01, 218.92 ± 9.59, 195.24 ± 18.29, 177.42 ± 17.55, and 117.86 ± 6.04 Mg C ha−1, respectively. In the forest ecosystem C stocks of the basin, soils averagely contribute about 73.78%, not including root underground biomass. It provides a comprehensive method for forest ecosystem carbon investigation and forest management in small basin scale.

I present the first complete theory of ADHD. ADHD occurs when the organism adapts to try to maintain higher glucose levels than normal. The main mechanism via which this is done is by faster opening of KATP channels, mainly Kir6.2/SUR1, which increases the cell's intrinsic \xtblty. I show that this induces all of the symptoms of ADHD. The optimal treatment for ADHD already exists, since drugs of the sulfonylurea family close KATP channels and have been used for safely treating people for dozens of years.

Data obtained by Direct Numerical Simulations (DNS) of pressure-driven turbulent channel flow are studied in the range 180 ≤ Reτ≤ 10,000. Reynolds number effects on the Mean Velocity Profile (MVP) and second order statistics are analyzed with a view of finding logarithmic behavior in the overlap region or even further from the wall, well in the boundary layer’s outer region. Values of Kármán constant for the MVPs and the Townsend-Perry constants for the streamwise and spanwise fluctuation variances are determined for the Reynolds numbers considered. A data-driven model of the MVP, proposed and validated for zero pressure gradient flow over a flat plate, is employed for pressure-driven channel flow by appropriately adjusting Coles’ strength of the wake function parameter, Π. There is excellent agreement between the analytic model predictions of MVP and the DNS-computed MVP as well as of the Reynolds shear stress profile. The skin friction coefficient Cf is calculated analytically. The agreement between the analytical model predictions and the DNS-based computed discrete values of Cf is excellent.

Our study provides guidelines on how to build long-term customer relationship in the non-contract mechanism context. More specifically, the findings show that special, social, and core benefits influence calculative commitment, and operational and special benefits influence affective commitment. This study also supports that calculative and affective commitment play a crucial role in understanding multi-channel agencies’ loyalty. In sum, this study revealed that calculative and affective commitment can be considered as partial or full mediators in the relationship between RBs (relational benefits) and loyalty. This study not only contributed to the existing SET (social exchange theory) and RBs paradigm but also provided practical implications for food distribution management.

Microcombs provide a potential compact and efficient light source for multi-Terabit-per-second optical superchannels. However, as the bandwidth of these multi-wavelength light sources is increased, this can result in low per-line power. Optical amplifiers can be used to overcome power limitations, but the accompanying spontaneous optical noise can degrade performance in optical systems. To overcome this issue, we propose wideband noise reduction for comb lines using a high-Q microring resonator, whose resonances align with comb lines. When applying the proposed distillation to a superchannel system with 18 Gbaud, 64-QAM sub-channels in a > 10 Tb/s optical superchannel, we find that noise-corrupted comb lines can reduce the optical signal-to-noise ratio required for the comb by ~ 9 dB when used as optical carriers at the transmitter side, and by ~ 12 dB when used as a local oscillator at the receiver side.