This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

The signature of chaotic systems can be characterized either by the sensitivity of the initial conditions or by the change of its parameters. This feature can be used for manufacturing high sensitivity sensors. Sensors based on chaotic circuits have already been used for measuring water salinity, inductive effects, and both noise and weak signals. This article investigates an impedance sensor based on the Van der Pol and Duffing damped oscillators. The calibration process is a key point and therefore the folding behavior of signal periods was also explored. A sensitivity of 0.15 kΩ/Period was estimated over a range from 89.5 to 91.6 kΩ. This range can be adjusted according to the application by varying the gain of the operational amplifier used in this implementation. The development of this type of sensor might be used in medical and biological engineering for skin impedance measurements, for example. This type of chaotic sensor has the advantage of sensing small disturbances and then detect small impedance changes within biological materials which, in turn, may not be possible with other detectors.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

Oncolytic virotherapy is a promising immunotherapy approach for cancer treatment, utilizing viruses to preferentially infect and eliminate cancer cells while stimulating immune responses. In this review we synthesize current literature on the molecular circuits of immune sensing and response to oncolytic virotherapy; focusing on viral DNA or RNA sensing by infected cells, cytokine and danger-associated signal sensing by neighboring cells, and subsequent downstream activation of immune pathways. The sequential sense-and-response mechanisms involve the triggering of molecular sensors by viruses or infected cells to activate transcription factors and related genes for a breadth of immune responses. We describe how molecular signals induced in the tumor upon virotherapy can trigger diverse immune signaling pathways, activating both antigen-presenting cell-based innate and T cell-based adaptive immune responses. Insights into these complex mechanisms provide valuable knowledge for enhancing oncolytic virotherapy strategies.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

In the previous work in Ref.[1], we presented a new interaction scheme that describes the interaction of thermodynamic systems. Using this interaction scheme, we showed that the interactions of dark matter and dark energy are chaotic. We also predicted that the results could be generalized to all particle and thermodynamic systems. In addition, we gave physical definitions of the concepts of chaos and self-organization. More importantly, we proposed a new law of physics based on interacting systems. In this study, we will consider two thermodynamic systems interacting under different conditions to prove the universality of the physical law we propose. We will show that these systems also have chaotic interaction dynamics.

The development of integrated, compact, and multifunctional photonic circuits is crucial to increase the capacity of all-optical signal processing for communications, data management or microsystems. Plasmonics brings compactness to numerous photonic functions, but its integration into circuits in not straightforward due to insertion losses and poor modes matching. The purpose of this article is to detail the integration strategies of plasmonic structures on dielectric waveguides, and to show through some examples the variety and the application prospect of integrated plasmonic functions.

This work presents a new type of chaotic dynamical system originated from Dirichlet Eta function. Although the exposition describes only a bidimensional instance, it is certainly possible to construct higher dimensional such models. The novelty resides in the multitude of interesting characteristics concentrated in only one kind of dynamical system, mainly because of its simple abstract definition - it provokes dissipative, chaotic and itinerant behavior, and its paths typically display nonrecurring quasi-attractors and associate regions of ruin. In addition, it is discrete and nonautonomous, being additively driven by a simple real vector sequence. Also, the defining formulas have parameters which permit to activate bifurcatory effects, mainly related to setting the number of quasi-attractors and overall geometric complexity and diversity. In this fashion, it holds a certain similarity with classical itinerant chaotic systems, but it is a completely different object. One of its parameters is very influential and may be intuitively compared to a type of "potential energy", capable of changing the duration of sojourns etc. In this fashion, there is a potential opportunity to employ artificial inference techniques for designing specific structures on paths. Of course, the other parameters are also relevant, but not necessarily in the control of the number of quasi-attractors and the permanence periods near them. It is important to state that the described system was found during a previous investigation about certain features of the Riemann hypothesis, using the Dirichlet Eta function instead of the Riemann Zeta function - the components of the system under study here were part of certain series whose convergence had to be established, and that scenario produced this very positive side effect. The text also suggests an atypical, but important, potential application in philosophy: the representation of the Hindu concepts of Samsara and Moksha.

In former times, the spinal cord was considered a hard-wired network for spinal reflexes and a conduit for long-range connections. This view has changed dramatically over the past few decades. It is now recognized as a plastic device whose structures and functions adapt to changing circumstances. While such changes also occur under physiological conditions, the most dramatic alterations take place during or after various pathological events. It is astonishing what mechanisms the musculo-skeletal system has evolved to come to grips with the damages. Many of these changes are maladaptive, but some appear to help adapt to the new conditions. Although myriads of studies, using manifold methods, have been devoted to elucidating the underlying mechanisms, in humans and animal models, the etiology and pathophysiology of various diseases are still little understood, due to a number of reasons. We will here try to summarize some results and remaining problems in a selection of diseases, in particular spinal muscular atrophy (SMA), amyotrophic laterals sclerosis (ALS), and predominantly spinal cord injury (SCI) with occasional relations to stroke. Especially the changes in SCI (and stroke) depend on the cause, site and extent of the afflicted damage and are therefore multifarious. At the end, we will briefly summarize results indicating that operant, classical and instrumental conditioning can be used to produce plastic changes in healthy people, with potentials for applications to patients with spinal cord injury. In order not to overload the article, we will not delve deeply into sub-cellular processes.

Instead of the conventional 0 and 1 values, bipolar reasoning uses -1, 0, +1 to describe double-sided judgements in which neutral elements are halfway between positive and negative evaluations (e.g., “uncertain” lies between “impossible” and “totally sure”). We discuss the state-of-the-art in bipolar logics and recall two medieval forerunners, i.e., William of Ockham and Nicholas of Autrecourt, who embodied a bipolar mode of thought that is eminently modern. Starting from the trivial observation that “once a wheat sheaf is sealed and tied up, the packed down straws display the same orientation”, we work up a new theory of the bipolar nature of networks, suggesting that orthodromic (i.e., feedforward, bottom-up) projections might be functionally coupled with antidromic (i.e., feedback, top-down) projections via the mathematical apparatus of presheaves/globular sets. When an entrained oscillation such as a neuronal spike propagates from A to B, changes in B might lead to changes in A, providing unexpected antidromic effects. Our account points towards the methodological feasibility of novel neural networks in which message feedback is guaranteed by backpropagation mechanisms endowed in the same feedforward circuits. Bottom-up/top-down transmission at various coarse-grained network levels provides fresh insights in far-flung scientific fields such as object persistence, memory reinforcement, visual recognition, Bayesian inferential circuits and multidimensional activity of the brain. Implying that axonal stimulation by external sources might backpropagate and modify neuronal electric oscillations, our theory also suggests testable previsions concerning the optimal location of transcranial magnetic stimulation’s coils in patients affected by drug-resistant epilepsy.

An exploding demand for processing capabilities related to the emergence of the IoT, AI and big data, has led to the quest for increasingly efficient ways to expeditiously process the rapidly increasing amount of data. These ways include different approaches like improved devices capable of going further in the more Moore path, but also new devices and architectures capable of going beyond Moore and getting more than Moore. Among the solutions being proposed, Stochastic Computing has positioned itself as a very reasonable alternative for low-power, low-area, low-speed, and adjustable precision calculations; four key-points beneficial to edge computing. On the other hand, chaotic circuits and systems appear to be an attractive solution for (low-power, green) secure data transmission in the frame of edge computing and IoT in general. Classical implementations of this class of circuits require intensive and precise calculations. This paper discusses the use of the SC framework for the implementation of nonlinear systems, showing that it can provide results comparable to those of classical integration, with much simpler hardware, paving the way for relevant applications.

Recent biotechnological innovations make feasible the new paradigm of creating biological neural circuits de novo. With advances in protein, cell and tissue engineering techniques, as well as cellular reprogramming methods, we are entering an era where the construction of neural circuits can open completely new ways for studying nervous systems and for treating nervous system disorders. I explore here three technologies, namely cellular engraftment, neuronal reprogramming and transsynaptic molecule engineering, and delineate how they are being used in a variety of basic research and translational medicine contexts. In basic neuroscience, neural circuit construction methods are enabling ways to study causality in neural development (e.g. neural precursor differentiation and migration) and circuit function (e.g. excitation/inhibition balance, neural population dynamics). In translational neuroscience, they are providing opportunities for the targeted correction of circuit malfunction in brain disorders, both psychiatric (e.g. schizophrenia) and neurological (e.g. Parkinson’s, Huntington’s and Alzheimer’s disease, as well as epilepsy). I discuss the challenges that these methods currently face, such as targeting specificity and cell survival, and outline future paths and opportunities to realize the full potential of technologies for creating new biological neural circuits.

In view of the problem of cracking easily and partial distortion of images after encryption or decryption, a novel image encryption and decryption algorithm based on Arnod Transform and fractional chaotic is proposed. To begin with, the Arnold transform is used to encrypt. So that the spatial confidence of the original image has been comprehensively disturbed. Secondly, the XOR involving the fractional order chaotic sequence is used to encrypt. The key sequence is dynamically generated to ensure the randomness and difference of key generation. When decryption is required, the first decryption is performed using the key and XOR. Then the second decryption is carried out by using the inverse Arnold transform, and finally the decrypted image is obtained. Experimental results show that the improved algorithm has achieved better performance in encryption and decryption.

Twice-exceptional learners face a unique set of challenges arising from the intersection of extraordinary talent and disability. Neurobiology research has the capacity to complement pedagogical research and provide support for twice-exceptional learners. Very few studies have attempted to specifically address the neurobiological underpinnings of twice-exceptionality. However, neurobiologists have built a broad base of knowledge in nervous system function spanning from the level of neural circuits to the molecular basis of behavior. It is known that distinct neural circuits mediate different neural functions, which suggests that 2e learning may result from enhancement in one circuit and disruption in another. Neural circuits are known to adapt and change in response to experience, a cellular process known as neuroplasticity. Plasticity is controlled by a bidirectional connection between the synapse, where neural signals are received, and the nucleus, where regulated gene expression can return to alter synaptic function. Complex molecular mechanisms compose this connection in distinct neural circuits, and genetic alterations in these mechanisms are associated with both memory enhancements and psychiatric disorder. Understanding the consequences of these changes at the molecular, cellular, and circuit levels will provide critical insights into the neurobiological bases of twice-exceptional learning.

Biological systems often need to operate in complex environments where conditions can rapidly change. This is possible due to their inherent ability to sense changes and adapt their behavior in response. Here, we detail recent advances in the creation of synthetic genetic parts and circuits whose behaviors can be dynamically tuned through a variety of intra- and extra-cellular signals. We show how this capability lays the foundation for implementing control engineering schemes in living cells and allows for the creation of biological systems that are able to self-adapt, ensuring their functionality is maintained in the face of varying environmental and physiological conditions. We end by discussing some of the broader implications of this technology for the safe deployment of synthetic biology.

We consider a random dynamical system arising in a model of associative memory. This system can be seen as a small (stochastic and deterministic) perturbation of a determinstic system having two weak attractors which are destroyed after the perturbation. We show, with a computer aided proof, that the system has a kind of chaotic itineracy. Typical orbits are globally chaotic, while they spend relatively long time visiting attractor's ruins.

Quantum-dot cellular automata (QCA) is an emerging transistor-less field-coupled nanocomputing (FCN) approach to ultra-scale ‘nanochip’ integration. In QCA, to represent digital circuitry, electrostatic repulsion between electrons and the mechanism of electron tunnelling in quantum dots are used. QCA technology can surpass conventional complementary metal-oxide semiconductor (CMOS) technology in terms of clock speed, reduced occupied chip area, and energy efficiency. To develop QCA circuits, irreversible majority gates are typically used as the primary components. Recently, some studies have introduced reversible design techniques, using reversible majority gates as the main building block, to develop ultra-energy efficient QCA circuits. However, this approach resulted in time delays, an increase in the number of QCA cells used, and an increase in the chip area occupied. This work introduces a novel hybrid design strategy employing QCA irreversible, reversible, and partially reversible gates to establish an optimal balance between power consumption, delay time, and occupied area. The hybrid technique allows the designer to have more control over the circuit characteristics to meet different system needs. A combination of reversible, irreversible, and innovative partially reversible majority gates is used in the proposed hybrid design method. We have evaluated the hybrid design method by examining the half-adder circuit as a case study. We have developed four hybrid QCA half-adder circuits, each of which simultaneously incorporates various types of majority gates. The QCADesigner-E 2.2 simulation tool was used to simulate the performance and energy efficiency of the half-adders. This tool provides numerical results for the circuit input/output response and heat dissipation at the physical level, within a microscopic quantum mechanical model.

Image encryption based on chaotic maps is an important way to ensure the secure communication of digital multimedia on the Internet. To improve the encryption performance and security of image encryption systems, a new image encryption algorithm is proposed by employing a compound chaotic map and random cyclic shift. Firstly, an improved Hybrid chaotic system is designed by coupling Logistic, ICMIC, Tent, and Chebyshev maps (HLITC). Comparison tests with previous chaotic maps in terms of chaotic trajectory, Lyapunov exponent, and Kolmogorov entropy illustrate the new hybrid chaotic map has better chaotic performance. Then the proposed HLITC chaotic system is used to develop a new chaotic image encryption scheme with the double cyclic shift. The improved HLITC chaotic system is performed to generate key sequences used in the image scrambling and diffusion stage. The spiral transformation controlled by chaotic sequence is used to scramble the pixels of the plaintext image, while the XOR operation based on a chaotic map is used for pixel diffusion. Extensive experiments of statistical analysis, key sensitivity, and keyspace analysis are conducted. Experimental results show the proposed encryption scheme has good robustness against brute force attacks, statistical attacks, and differential attacks, and is more effective than many existing chaotic image encryption algorithms.

Three body systems in which one of the bodies is ejected without escaping the binary system have previously been studied in various restricted forms. However, none of these studies dwells on the problem in a general setting. Thus, to study this phenomenon qualitatively, we try to expand this problem's scope to unequal mass systems and generalize them by considering various configurations of fixed initial points with precisely calculated initial velocities, some zero velocity models and some optimized models. We will see the use of terminology similar to the previous studies done in this domain but incorporate different analytical and evaluation methods.

We humans are natural-born engineers. As such, we model after machines not only isolated, naturally occurring systems, but also the basic laws of physics, sharing with machines a local-evolution-of-state `grammar'. However, previous work by the author casts doubt upon this mechanistic paradigm, suggesting that it is to blame for the stubbornness of many open problems in physics. Simple experiments are therefore proposed to identify `non-machines'. In one experiment, `non mechanistic correlations' in the spirit of Bell are sought in a pair of separated but previously coupled (macroscopic) chaotic systems. In another it is tested whether chaotic systems could fuzzily `remember their future' in the sense that a future binary perturbation applied to them could be inferred from their present behavior with probability>1/2. Chaotic systems are chosen as candidates because the long-time application of their (deterministic) mechanistic description is conceptually groundless: All scales are significant and mutually coupled in that regime, down to scales governed by QM, yet the quantum-classical transition remains inexplicable---if only due to the measurement problem. Similarly for non-deterministic chaotic systems, modeled as such purely for defying a short-time deterministic mechanistic description. Should a non mechanistic signature be found in such simple systems, the implications for science as a whole and life sciences in particular cannot be overstated.

The paper is dedicated to the numerical and experimental study of nonlinear oscillations exhibited by the Vilnius chaotic generator. The need for practical applicability of the mentioned generator in chaotic communication systems defined the necessity to study the operation of the circuit in a wide parameter range. The bifurcation maps and corresponding one-parameter diagrams, obtained and analysed utilising the Method of Complete Bifurcation Groups, reveal the complex nonlinear dynamics and regions of robust chaotic oscillations. Laboratory experiments allow the verification of the numerical results and identification of the most practically relevant phenomena.

This paper suggests a novel one-dimensional (1D) map to address the limitations of traditional chaotic 1D maps. The main challenge with traditional chaotic 1D maps is the limited control parameter range and the potential risk of collapsing as a result under the finite precision implementation. To overcome these limitations, the new 1D map hybridises the traditional logistic map with tent map, and a linear tent-like function. This hybridization results in a wider range of control parameters to produce chaotic behavior. The dynamic behavior of the new 1D map has been analyzed using well known numerical methods, including the bifurcation diagram and Lyapunov exponent. Both tests have shown their complex and diverse behavior. In addition, a novel image encryption scheme has been devised using the new function as its pseudo-random-number generator. The proposed encryption algorithm has been tested and found to be robust and secure, passing all statistical tests applied to the encrypted images. The results of this study demonstrate the effectiveness of the new 1D map for use in secure image cryptography applications, providing a more robust and secure alternative to traditional chaotic 1D maps. The proposed algorithm has demonstrated high performance in NPCR and UACI tests. It also has shown good results in the MSE and PSNR tests.

The Van der Pol oscillator is a chaotic non-linear system. Small perturbations in initial conditions may result in wildly different trajectories. Because of its chaotic nature, controlling, or forcing, the behavior of a Van der Pol oscillator is difficult to achieve through traditional adaptive control methods. Connecting two Van der Pol oscillators together where the output of one oscillator, the driver, drives the behavior of its partner, the responder, is a proven technique for controlling the Van der Pol oscillator. Deterministic AI (DAI) is an adaptive feedback control method that leverages the known physics of the Van der Pol system to learn optimal system parameters for the forcing function. We assessed the performance of DAI employing three different online parameter estimation algorithms. Our evaluation criteria include mean absolute error (MAE) between the target trajectory and the response oscillator trajectory over time. RLS with exponential forgetting (RLS-EF) had the lowest MAE overall, with a 2.46% reduction in error. However, another method was notable. Least Mean Squares with normalized gradient adaptation (LMS-NG) had worse initial error in the first 10% of the simulation, but after that point had consistently better performance. We found that over the last 90% of the simulation, DAI with LMS-NG had a 48.7% reduction in MAE compared to feedforward alone.

This paper presents the common methods and corresponding drawbacks concerning nonlinear analysis of fluxgate excitation circuits and emphasizes the importance of nonlinear analysis for these circuits. With regard to the nonlinearity of the excitation circuit, this paper proposes the use of the core-measured hysteresis curve for mathematical analysis and the use of a nonlinear model that considers the coupling effect of the core and winding and influence of the historical magnetic field on the core for simulation analysis. The feasibility of mathematical calculations and simulation for the nonlinear study of fluxgate excitation circuit is verified via experiments. The results demonstrate that, in this regard, the simulation is better than a mathematical calculation. The simulation and experimental results of the excitation current and voltage waveforms under different excitation circuit parameters and structures are essentially consistent with each other, thereby verifying the effectiveness of the nonlinear excitation analysis method.

This paper reports a new global Mittag-Leffler synchronization criterion with regard to fractional-order hyper-chaotic financial systems by designing the suitable impulsive control and the state feedback controller. The significance of this impulsive synchronization lies in the fact that the backward economic system can synchronize asymptotically with the advanced economic system under the effective impulse macroeconomic management means. Matlab LMI-toolbox is utilized to deduce the feasible solution in numerical example, which shows the effectiveness of the proposed methods. It is worth mentioning that the LMI-based criterion usually requires the activation function of the system to be Lipschitz, but the activation function in this paper is fixed and truly nonlinear, which cannot be assumed to be Lipschitz continuous. This is another mathematical difficulty overcome in this paper.

Since its original publication 1 in 1978, Lozi’s chaotic map has been thoroughly explored and continues to be. Hundreds of publications analyze its particular structure or apply its properties in many fields (electronic devices like memristor, A.I. with swarm intelligence, etc.). Several generalizations have been proposed, transforming the initial two-dimensional map into multidimensional one. However, they do not respect the original constraint that allows this map to be one of the few strictly hyperbolic: a constant Jacobian. In this paper we introduce a three-dimensional piece-wise linear extension respecting this constraint and we explore a special property never highlighted for chaotic mappings: the coexistence of thread-chaotic attractors (i.e., attractors which are formed by collection of lines) and sheet-chaotic attractors (i.e., attractors which are formed by collection of planes). This new 3-dimensional mapping can generate a large variety of chaotic and hyperchaotic attractors. We give five examples of such behavior in this article. In the first three examples, there is coexistence of thread and sheet-chaotic attractors. However, their shape are different and they are constituted by a different number of pieces. In the two last examples, the blow up of the attractors with respect to parameter a and b is highlighted.

The Ising model, a cornerstone in the understanding of critical points, phase transitions, and magnetic systems, has been pivotal in advancing our knowledge of statistical physics. Although analytical solutions exist for the 1D and 2D Ising models, complexities rise significantly with the inclusion of external magnetic fields and in higher dimensions. Here, we demonstrate a novel quantum computational approach to simulate the 1D Ising model with basic quantum gates in the QISKIT(Python) that is both accessible to beginners and executable on personal computers, bypassing the need for advanced computational infrastructure. By initializing the system in a comprehensive superposition state, we effectively utilize quantum gates to replicate the intricate interactions between spins and external fields. This method offers a more intuitive and direct observational means of the system's evolution, distinguishing it from previous methodologies. Our results not only repeat all the physics behavior in the 1D Ising model but also showcase the expanding capabilities of quantum computing to tackle complex physical systems, promising advancements in both theoretical and applied physics.

Vertical-channel organic dual-gate/base transistors would be highly interesting since vertical organic transistors are the fastest organic transistors demonstrated today. However, incorporating a dual gate/base structure into an ultra-short channel vertical architecture represents a substantial challenge. Here, we successfully realize a new device concept of vertical organic permeable dual-base transistors (OPDBTs), where either of both base electrodes can be used to change the on-currents and tune the threshold voltages. The optimized devices yield a high on-current density of 1.54 A cm^-2 and a large current gain of 9.2×10⁵, corresponding to a high transmission value of 99.998%. The detailed operation mechanisms are investigated by calibrated TCAD simulations with the Poole-Frenkel mobility model, Gaussian density of states and tunneling model. Finally, high-performance logic circuits, e.g. inverter, NAND/AND computation functions are demonstrated with one single OPDBT operating at supply voltages of < 2.0 V. We believe that OPDBTs offer a compact and technologically simple hardware platform with excellent application potential for vertical-channel organic transistors in complex logic circuits.

The transportation sector is seeing an increased adoption rate of electric vehicles (EV), which comprise battery electric vehicles (BEV), hybrid electric vehicles (HEV) and plug-in hybrid electric vehicles (PHEV). This mode of transportation is likely to displace automobiles powered by internal combustion engines (ICE) in the nearest future, as indicated by the current trend. Each of the key EC components is home to a variety of technologies that are either currently in use or will be in the near future. Electric vehicles have the potential to have a significant impact on a variety of fields, including the economy, the energy infrastructure, and the natural environment. As a result of the production of carbon dioxide gas from the combustion of fossil fuels, transportation is the sector that is responsible for the second-highest amount of greenhouse gas emissions. Electric vehicles, often known as EVs, are getting a lot of attention as a potentially game-changing solution to this issue. It is possible for electric vehicles to produce fewer emissions of carbon dioxide (CO2) than conventional automobiles due to the fact that an electric motor serves as the vehicle's propeller rather than an internal combustion engine. EVs have the potential to become zero-emission vehicles if they are paired with renewable energy sources. This document presents an overview of the numerous types of EV drive circuits, covering their design as well as the benefits and drawbacks associated with each type. The current state of battery technology, particularly that pertaining to the batteries utilized in electronic vehicles, is discussed in this paper. This article also discusses electric motor efficiency, power density, fault tolerance, dependability, cost, and the best electric motor for EVs. Then, a thorough study of future EV implementation's obstacles and prospects is done. Charging times and battery performance are examples of technological challenges, but government regulation of EVs continues to be a substantial non-technical hurdle.

We apply a well known technique of theoretical physics, known as Geometric Algebra or Clifford algebra, to linear electrical circuits with non-sinusoidal voltages and currents. We rederive from the first principles the Geometric Algebra approach to the apparent power decomposition. The important new point consists in a choice of a natural convenient basis in the Clifford vector space which simplifies considerably the presentation. Thus we are able to derive a number of general results which are missing in the former papers. In particular, a natural correspondence with the Current Physical Components approach is shown.

In real financial market, the delayed market feedback and the delayed effect of government macro-control are inevitable. And both the delay of market feedback and the delay of macro-control effect bring about the mathematical difficulties in studying stabilization and synchronization of the hyper-chaotic financial system. However, employing Lyapunov function method, differential mean value theorem, suitable bounded hypotheses and pulse control technology results in the globally asymptotical stabilization and synchronization criteria. It is the first paper to drive the stabilization and synchronization criteria under the assumptions of the double delays. Finally, numerical examples illuminate the effectiveness of the proposed methods.

This article addresses the trajectory tracking between two non-identical systems with chaotic properties. We employ the Rossler chaotic and RCL-shunted Josephson junctions model in similar phase space to study trajectory tracking. In order to achieve the goal tracking, we afford two stages to approximate the target tracking. The first stage utilizes the active control technique to transfer the output signal from the RCLs-J system into the quasi-Rossler system. Then next, the RCLs-J system employs the proposed the iterative learning control scheme and the control signal from the drive system to trace the trajectory of Rossler system. The numerical results demonstrate the proposed method and the tracking system is asymptotically stable.

(1) In order to study the influence of chaotic system on wheat image encryption, a method to find the optimal chaotic system encryption based on wheat image is proposed. (2) 10 different chaotic system schemes are combined to encrypt wheat images by 13 common chaotic maps, respectively. The best chaotic system scheme is obtained by considering the anti-attack capability of these encryption schemes, which analyzes 8 commonly used image encryption performance evaluation indexes. (3) The experimental results show that the new four-dimensional chaotic system has the best encryption effect, which is suitable for wheat image encryption. (4) The proposed scheme of wheat image encryption based on chaotic system provides a reference for other crop image encryption.

The Chen circuit system, a three-dimensional autonomous system with intriguing dynamics, has gained considerable attention due to its potential applications in diverse scientific fields. In this article, a Chen circuit-like system is defined and a comprehensive dynamics has been studied. The system exhibits chaotic dynamics, limit cycles, and bifurcations, making it a captivating subject of study. By employing numerical simulations and analytical techniques, we explore the system's stability and identify critical parameter values leading to qualitative changes. Notably, we delve Hopf bifurcations, which give rise to stability changes and the emergence of limit cycles. Furthermore, we analyze the fractal dimension of the system's attractor, providing insights into its complexity and self-similarity. Through a systematic examination of the Chen circuit-like system, we deepen our understanding of its intricate dynamics and offer valuable insights into the underlying mechanisms. The findings contribute to the field of dynamical systems and hold potential implications in areas such as chaos-based secure communications, signal processing, and nonlinear control. This work serves as a valuable reference for researchers and practitioners interested in the dynamics and bifurcation analysis of nonlinear systems.

Decision-makers are concerned with the inherent complexity of the modern world's markets. However, price fluctuations, environmental concerns, technological development, emerging markets, political challenges, and social expectations made the 21^st century's more dynamic and complex. From a policy-making perspective, it is vital to uncover future trends. This paper proposed that artificial intelligence can improve interpretations in complex markets, such as financial and energy markets. In a complex environment, it is critical to investigate maximum available input features to ensure no valuable informative feature is neglected. Some AI-based models are investigated and presented that AI-based models can successfully uncover future trends. From a scenario development perspective purified input features subset refer to driving forces which shape alternative futures. Results showed that using AI can improve our understanding of how input features influence future behaviors and simultaneously improves prediction accuracy and reliability.

Being able to forecast events is of great importance in many fields, from brain behavior to earthquakes or stock markets. Because each dynamical system has intrinsic features, different statistical tools have to be used for each system. Here we study the time series of the output intensity of a fiber laser with an ordinal patterns analysis, and we look for temporal correlations in order to statistically forecast the most intense events. We set two thresholds, a low one and a high one, to distinguish between low intensity versus high intensity events. We find that when the time series is performing events below the low threshold it shows some preferred temporal patterns before performing events above a high threshold.

Non-linear loads in circuits cause the appearance of harmonic disturbances both in voltage and current. In order to minimize the effects of these disturbances and, therefore, to control over the flow of electricity between the source and the load, they are often used passive or active filters. Nevertheless, determining the type of filter and the characteristics of their elements is not a trivial task. In fact, the development of algorithms for calculating the parameters of filters is still an open question. This paper analyzes the use of genetic algorithms to maximize the power factor compensation in non-sinusoidal circuits using passive filters, while concepts of geometric algebra theory are used to represent the flow of power in the circuits. According to the results obtained in different case studies, it can be concluded that the genetic algorithm obtain high quality solutions that could be generalized to similar problems of any dimension.

This paper proposes a novel concept within Quantum Natural Language Processing (QNLP) to encode the interpersonal metafunction of Systemic Functional Linguistics (SFL), particularly tenor, into quantum circuits by treating Japanese honorifics seriously. Because of English language bias in the literature, the incorporation of nuanced aspects of interpersonal communication evident in languages, such as the aforesaid Japanese, remains under-developed and overlooked. Utilizing lambeq, monoidal categories, and string diagrams, this study extends lambeq’s quantum computing framework to capture not only grammar but also social context—specifically the roles and relationships that define interpersonal interactions in quantum circuits. This approach represents a significant step toward that end simply by defining the honorific type h in lambeq. This innovative strategy exposes the capability of quantum circuits to model the complex structures of language, moving beyond grammar and even semantics—the horizontal, textual dimension of language—to embrace the vertical, hierarchical dimension of human communication and social interaction. Through this lens, the paper underscores the potential of QNLP to transcend traditional linguistic analysis, advocating for a broader and more nuanced understanding of language that includes not only what is said but also the social persona of the interlocutors. An algorithm for parsing Japanese grammar into pregroup diagrams containing the h type is introduced along with a codebase for other researchers to use and to which to contribute. Lastly, a toy experiment is performed to demonstrate that the circuits generated from these pregroup diagrams are suitable for Quantum Machine Learning (QML) applications.

In electric circuits, energy is delivered by electromagnetic fields through the space, as suggested by Kraus and Carver. They provide insights by showing electric/magnetic fields and Poynting vector directions around a DC circuit. In this work, the energy flow mechanism by Kraus and Carver is further studied theoretically for arbitrary terminal potentials of a DC power source.

This research not only dedicated a less restrictive method of iteration-varying function for a learning control law to design a controller but also synchronize two nonlinear systems with free time-delay. In addition, the mathematical theory of system synchronization has proved rigorously and the theory verified through an example to demonstrate the behavior of each parameter in the theory. The design of a controller using the iterative learning control law is significant for robotic tracking. The controller in this research generates a feed-forward control input using the error dynamics among the drive-response systems. The error dynamics satisfies the Lyapunov function and the combination of output errors, which respectively represented relative estimated differences of the drive-response systems. The iterative learning control rule serves the function of a filter adding previous control error after the end of each iteration. The numerical example of a synchronous system is given a Lorenz system for driving and another with the iterative learning control law for response under different initial condition. The results verify and demonstrate the proposed mathematical theory. The simulation exhibits consistency in the behavior of each parameter to match mathematical theory.

In the dairy industry a fundamental role is played by an efficient milk production, therefore even a slight shrinking in the production might have a significant consequence both on the industry profits and on the society. Milk is, in fact, one of the most common foods, and a fundamental support in the nutrition so that the lacking of milk should be avoided. An efficient milk production depends on various factors, but in particular it depends on the good health and supply of the dairy cow. However, in order to increase the milk production, cows are overfeed thus increasing their weight. Unfortunately, the overweight of the cows might easily damage their bones. In particular, the knee bones are fragile and they can easily swell and break. In order to analyze the knee bones and to compute a threshold leading to a damage, in this paper we study a bio-mechanical model of the knee joint and study the corresponding dynamical system. A novel dynamical model of dairy cow leg is constructed, in which the knee is represented by a complex structure of sliding and rolling. Then, the dynamic characteristics of the structure is analyzed by some numerical simulation. The results of the experiments shows that the solutions of the dynamical system might lead to a chaotic behavior. The evolution to chaos it explains the rising of various pathological features thus reducing the milk production.

Based on the fractional order of nonlinear system for love model with a periodic function as an external force, analyzed the characteristics of the chaotic dynamic in this study. The relationship between the chaotic dynamic of the fractional-love model with the external force and the fractional-order system was analyzed when the parameters are fixed. Further, we also studied the relationship between the chaotic systemic dynamic and the parameters when the fractional-order system is fixed. The results show that when the parameters are fixed, the fractional-order system exhibited segmented chaotic states for the different fractional orders of the system. When fixed the fractional-order system, the system exhibited the periodic and chaotic states as parameter changes.

The interaction between electromagnetic fields (EMFs) and biological systems has been a subject of intense research and debate. This study explores the potential influence of magnetic fields on neural circuits, which are the building blocks of the human brain. By developing a mathematical model and conducting computational simulations, we investigate how magnetic fields can affect the transmission of electrical signals within neural circuits. The results suggest that magnetic fields can alter the speed and direction of signal propagation, offering potential applications in medical treatments and brain-machine interfaces. However, the study also highlights the need for more comprehensive models that consider the complexity of real-world neural circuits and the multifaceted nature of magnetic fields. The interaction between EMFs and neural circuits is a rich and complex subject that requires a multidisciplinary approach, combining physics, biology, mathematics, and computer science. While this study provides valuable insights, further research is needed to fully understand the implications of this interaction and to realize its potential applications in medicine, neuroscience, and technology. The findings contribute to a growing body of knowledge that bridges the gap between physics and neuroscience, opening new horizons for understanding the human mind and its connection to the physical world.

In this paper, chaos sequence is used to replace the traditional Spread Spectrum sequence. From the perspective of the communication partner, a new method of generating the initial value of chaotic sequence is proposed, which is more suitable for the multi-base Spread Spectrum System and easy to extract. In order to further improve the error performance of the system and ensure the integrity of the system, an improved suboptimal soft information extraction method based on log-likelihood ratio (LLR) is proposed in the channel coding module, which can further improve the error performance of the system. On this basis, we choose the synchronization mode of multiple transmission of one reference signal to solve the problem that chaotic sequence is difficult to obtain synchronization because of its aperiodic characteristics. Finally, the system is simulated in the channel with low SNR. The simulation results show that chaotic sequence as Spread Spectrum code can make the signal transmit accurately in the worse channel environment. The performance gain of applying soft information decoding decision in the M-ary Spread Spectrum System with chaotic sequence as Spread Spectrum code can reach 5.2dB compared with the traditional Direct Spread Spectrum System.

A developed six-port reflectometry (SPR) system was integrated to measure the relative permittivity of tumor and normal breast tissue for medical diagnostic purpose. In order to obtain an accurate and precise measurement, the calibration process was done to the SPR using the well-known three-standard technique. Next, the studied dielectric probe was connected to the calibrated measurement-port of the SPR. The open end of the probe aperture was dibbed into the normal and tumor synthetic breast tissue samples to measure the synthetic breast tissues dielectric constant, ɛrʹ, and loss factor, ɛrʺ in the frequency range of 1.5 GHz to 3.3 GHz. Finally, the comparative studies were conducted between commercial VNA with Keysight 85070E dielectric probe and the studied SPR-probe system based on the measured magnitude of the reflection coefficient, phase shift, dielectric constant, and loss factor of the synthetic breast samples. The maximum absolute errors of the measured reflection coefficient magnitude, phase shift, dielectric constant, and loss factor were found to be 0.01, 1.07°, 1.12, and 0.75, respectively. It was ascertained that the predicted dielectric constant, ɛrʹ, is able to differentiate between normal, (ɛrʹ &lt; 50) and tumor, (ɛrʹ &gt; 50) breast tissues.

Using the example of a generator model with dedicated inertia, a theoretical study of two coupled self-oscillators with capacitive coupling, their sequential single-frequency synchronization, chaos and two-frequency synchronization with an adiabatic change in the magnitude of the coupling between partial self-oscillators was carried out. The parameters of self-oscillators and the values of the coupling coefficient at which the specified operating modes of coupled self-oscillators exist are determined. The results of numerical studies, illustrating the conditions for excitation of single-frequency, chaotic and dual-frequency oscillations in a system of coupled self-oscillators are presented.

The occurrence of chaotic instability of oscillations at the output of a single-stage amplifier on a powerful bipolar microwave transistor when a biharmonic signal is amplified is considered. It has been established that at a high level of the input signal at the output of the amplifier, the signal contains a significant chaotic component. Cases were experimentally studied when the frequency distance between the partial frequency components of a biharmonic signal is close to the gain band and when it is much smaller than this band. It has been established that in the first case, the chaos in oscillations is associated with the emergence of a sequence of trains of a forced oscillatory process with arbitrary initial phases and durations. In the second case, the appearance of a chaotic pedestal is associated with the chaos in the passive underexcited mode of the nonlinear circuit formed by the capacitance of the p-n junction and the input matching circuits of the amplifier stage.

Recently, hybrid logic circuits based on magnetic tunnel junctions (MTJs) have been widely investigated to realize zero standby power. However, such hybrid CMOS/MTJ logic circuits suffer from a severe sensing reliability due to the limited tunnel magnetoresistance ratio (TMR≤150%) of the MTJ and the large process variation in the deep sub-micrometer technology node. In this paper, a novel differential sensing amplifier (DSA) is proposed, in which two PMOS transistors are added to connect the discharging branches and evaluation branches. Owing to the positive feedback realized by these two added PMOS transistors, it can achieve a large sensing margin. By using an industrial CMOS 40 nm design kit and a physics-based MTJ compact model, hybrid CMOS/MTJ simulations have been performed to demonstrate its functionality and evaluate its performance. Simulation results show that it can achieve a smaller sensing error rate of 9% in comparison with the previously proposed DSAs with the TMR ratio of 100% and process variation of 10%, while maintaining almost the same sensing delay of 74.5 ps and sensing energy of 1.92 fJ/bit.

The brain rhythms are essential for information processing in neuronal networks. Oscillations recorded in different brain regions can be synchronized and have a constant phase difference, i.e. be coherent. Coherence between local field potential (LFP) signals from different regions in the brain may be correlated with the performance of cognitive tasks, from which it is concluded that these regions of the brain are involved in the task performance together. In this review, we discuss why coherence occurs and how it is coupled to the information transfer between different regions of the hippocampal formation. Coherence in theta and gamma frequency ranges is described since these rhythms are most pronounced during the hippocampus-dependent attention and memory. We review in vivo studies of interactions between different regions of the hippocampal formation in theta and gamma frequency bands. The kay provisions of the review: 1) coherence emerges from synchronous postsynaptic currents in principal neurons, occurring as a result of synchronization of neuronal spike activity; 2) synchronization of neuronal spike patterns in two regions of the hippocampal formation can be realised through induction or resonance; 3) coherence at a specific time point reflects the transfer of information between regions of the hippocampal formation, in particular, gamma coherence reflects the coupling of active neuronal ensembles. Overall, coherence is not an epiphenomenon, but an important physiological process that has certain generation mechanisms and performs important functions in information processing and transmission across the brain regions.

Nervous systems and brains’ computational abilities are an evolutionary innovation, specializing and speed-optimizing ancient biophysical dynamics. Bioelectric signaling originated in cells’ communication with the outside world and with each other, in order to cooperate toward adaptive construction and repair of multicellular bodies. Here we review the emerging field of developmental bioelectricity, which links the field of basal cognition to state-of-the-art questions in regenerative medicine, synthetic bioengineering, cognitive science, and even machine learning and artificial intelligence. One of the predictions of this view is that regeneration and regulative development are able to restore correct large-scale anatomies from diverse starting states because, like the brain, they exploit bioelectric encoding of distributed goal states - in this case, pattern memories. Based on this idea, we propose a new interpretation of recent stochastic regenerative phenotypes in planaria, by appealing to computational models of memory representation and processing in the brain. Moreover, we discuss novel findings showing that bioelectric changes induced in planaria can be stored in tissue for over a week, thus revealing that somatic bioelectric circuits in vivo can implement a long-term, re-writable memory medium. A consideration of the mechanisms, evolution, and functionality of basal cognition makes novel predictions and provides an integrative perspective on the evolution, physiology, and biomedicine of information processing in vivo.

Since the requirements in terms of power of the electronic applications range wide, the developed Energy Harvesting (EH) systems limit their availability to the less power demanding applications. However, this paper focuses on increasing the energy levels collected in the EH system so that it can be included in more demanding applications in terms of power. Therefore, an electronic system capable of grouping many single harvesting channels into one single system is analyzed in this paper. This multi-harvester electronic system is able to manage efficiently the energy collected by multiple vibratory transducers. The paper includes a comparison of its performance against some of the State-of-the-Art EH energy management circuits that interface the transducers. The method employed to demonstrate the intrinsic efficiency of each of the electronic circuits tested was based on experimental tests, where the average power transferred from several identical and simultaneous electric sources to a single storage element was measured. It was found out that only one energy management circuit was able to increase the transferred energy in a linear way while new input electric sources were added.

The development of synthetic biology has enabled us to make massive progress on biotechnology and to approach research questions from a brand new perspective. In particular, the design and study of gene regulatory networks in vitro, in vivo and in silico, have played an increasingly indispensable role in understanding and controlling biological phenomena. Among them, it is of great interest to understand how associative learning is formed at the molecular circuit level. Noticeably, mathematical models have been increasingly used to predict the behaviors of molecular circuits. The Fernando’s model, which is thought to be one of the first works in this line of research using the Hill equation, attempted to design a synthetic circuit that mimics Hebbian learning in the neural network architecture. In this article, we carry out in-depth computational analysis of the model and demonstrate that the reinforcement effect can be achieved by choosing the proper parameter values. We also construct a novel circuit that can demonstrate forced dissociation, which was not observed in the Fernando’s model. Our work can be readily used as reference for synthetic biologists who consider implementing the circuits of this kind in biological systems.

In this paper, we propose a method for assessing the effectiveness of entropy features using several chaotic mappings. We anlyze fuzzy entropy (FuzzyEn) and neural network entropy (NNetEn) on four discrete mappings: the logistic map, the sine map, the Planck map, and the two-memristor-based map, with a base length time series of 300 elements. FuzzyEn is shown to have improved global efficiency (GEFMCC) in the classification task compared to NNetEn. At the same time, there are local areas of the time series dynamics in which the classification efficiency NNetEn is higher than FuzzyEn. The results of using horizontal visibility graphs (HVG) instead of the raw time series are also shown. GEFMCC decreases after HVG time series transformation, but there are local areas of the time series dynamics in which the classification efficiency increases after including the HVG. The scientific community can use the results to explore the efficiency of entropy-based classification of time series.

This paper introduces an approach that chooses the fault detection by calculating probabilities using probability mass function (pmf) and cumulative distribution function (CDF). This work used a method for multiple stuck-at faults by producing a new test pattern in combinational circuits. We assumed that existence of all multiple faults is only because of one single component that is faulty. A complete test set can be created by all possible single stuck-at faults in a combinational circuit using some combination of gates. The test set generation fault detection method is applied on two different 3-bit input variable and 4-bit input variable circuits. The probability of error occurrence is calculated at both 3-bit and 4-bit input variable circuits. The resulting feature is used to obtain maximum error occurrence probability to detect faults by the logic used that the complexity of the circuit is inversely proportional to the fault occurrence probability. Then again, undetectability is directly proportional to the complexity of the circuit. Therefore, finest feasible circuit should have large input variable components with less complexity to reduce the fault occurrence probability.

The development of printing technologies has enabled the realization of electric circuit fabrication on flexible substrate. However, the current technique remains restricted to single-layer patterning. In this paper, we demonstrate a fully solution-processable patterning approach for multi-layer circuits using a combined method of laser sintering and ablation. Selective laser sintering of silver (Ag) nanoparticle-based ink is applied to make conductive patterns on a heat-sensitive substrate and insulating layer. The laser beam path and irradiation fluence are controlled to create circuit patterns for flexible electronics. Microvia drilling using femtosecond laser through the polyvinylphenol-film insulating layer by laser ablation, as well as sequential coating of Ag ink and laser sintering, achieves an interlayer interconnection between multi-layer circuits. The dimension of microvia is determined by a sophisticated adjustment of laser focal position and intensity. Based on these methods, the flexible electronic circuit with chip-size-package light-emitting diodes was successfully fabricated and demonstrated with functional operations.

An approximation-free and fully quantum optic formalism for parametric processes is presented. Phase-dependent gain coefficients and related phase-pulling effects are identified for quantum Rayleigh emission and the electro-optic conversion of photons providing parametric amplification in small scale integration of photonic devices. These mechanisms can be manipulated to deliver, simultaneously, sub-Poissonian distributions of photons as well as phase-dependent amplification in the same optical quadrature of a signal field.

This study presents finite-time synchronization of chaotic fractional order systems with disturbance uncertainty and unknown time delay. First, a PID sliding surface is presented. Then, for the finite-time synchronization of the master and slave systems, a robust sliding-adaptive control method is provided. Update rules have been retrieved to estimate the system parameters by using the Lyapunov function while establishing the stability of the suggested mechanism and assuring the convergence of errors to zero. The proposed approach was used to solve the fractional order system of Gensou-Tsei with time-varying parameters, and the simulation results show that the presented approach performs well.

An extension of the models used to generate fractal traffic flows is presented by means of the formulation of a model that considers the use of one-dimensional chaotic maps. Based on the disaggregation of the temporal series generated by the model, a valid explanation of behavior of the values of Hurst exponent is proposed and the feasibility of their control from the parameters of the proposed model is shown.

Many advanced technologies have been employed in the high performance active matrix displays including liquid crystal displays, organic light emitting diode displays, and micro light emitting diode displays. On the other side, there have existed the strong demand on the cost reduction and it is one of low cost schemes to integrate the driver circuit in a panel based on thin film transistor technologies. This paper reviews overall concept, operation principles, and various circuit approaches in shift registers for the scanning pulse generation. In addition, it deals with the implementation of additional functionalities in gate drivers to support pixel compensation, multi-line driving, in-cell capacitive touch screen, pixel sensing, and adaptive scanning region control.

As technology advances, the field of electrical and computer engineering continuously demands the introduction of innovative new tools and methodologies to facilitate effective learning and comprehension of fundamental concepts. This research addresses an identified gap in technology-augmented education capabilities and researches the integration of Virtual Reality (VR) technology with real-time electronic circuit simulation to enable and enhance the visualization of non-observable concepts such as voltage distribution and current flow within these circuits. In this paper, we describe the development of our immersive educational platform, which makes understanding these abstract concepts intuitive and engaging. This research also involved the design and development of a VR-based circuit simulation environment. By leveraging VR’s immersive capabilities, our system enables users to physically interact with electronic components, observe the flow of electrical signals, and manipulate circuit parameters in real-time. Through this immersive experience, learners can gain a deeper understanding of fundamental electronic principles, transcending the limitations of traditional two-dimensional diagrams and equations. Furthermore, this research focuses on the implementation of advanced and novel visualization techniques within the VR environment for non-observable electrical and electromagnetic properties, providing users with a clearer and more intuitive understanding of electrical circuit concepts. Examples include color-coded pathways for current flow and dynamic voltage gradient visualization. Additionally, real-time data representation and graphical overlays are researched and integrated to offer users insights into the dynamic behavior of circuits, allowing for better analysis and troubleshooting.

Considering the isotropic release process of nanoelectromechanical systems (NEMS), defining the active region of NEM memory switches is one of the most challenging process technologies for the implementation of monolithic-three-dimensional (M3D) CMOS-NEM hybrid circuits. In this paper, we propose a novel encapsulation method of NEM memory switches. It uses alumina (Al2O3) passivation layers which are fully compatible with CMOS baseline process. The Al2O3 bottom passivation layer can protect intermetal dielectric (IMD) and metal interconnection layers from vapor hydrogen fluoride (HF) etch process. Thus, the controllable formation of the cavity for the mechanical movement of NEM memory switches can be achieved without causing any damage to CMOS baseline circuits as well as metal interconnection lines. As a result, NEM memory switches can be located in any places and metal layers of an M3D CMOS-NEM hybrid chip, which makes circuit design easier and more volume-efficient. The feasibility of our proposed method is verified based on experimental results.

In this paper, we study the effect of parasitic channel on electrical characteristics and power consumptions of vertically stacked gate-all-around (GAA) silicon nanosheet (NS) MOSFETs of the bulk and silicon-on-insulator (SOI) substrates. Through deliberate control of the bottom parasitic channel coverage, we systematically assess its influence on DC, AC, and RF characteristics including power consumption. The observed findings highlight a significant differentiation among the bottom parasitic channels: GAA (i.e., control sample with 100% coverage), omega-shaped gate NS (70% and 80% coverages), and FinFET (60% coverage). Compared with the device with a 60% coverage channel, the device with a 100% coverage channel possesses 3520% and 8030% normalized leakage current improvement for both NFET and PFET under the bulk substrate, respectively. Compared with bulk-substrate devices, the SOI-substrate devices further significantly improve the leakage current. Due to enhanced off-state current leakages in the 100% covered bulk-substrate device, the static power demonstrates a notable improvement (about 98.1%), compared to 60% covered devices. Hence, the utilization of a 60% covered channel will result in a degradation of both device and circuit performance. The observation of GAA NS MOSFET indicates that an increase in the bottom parasitic channel coverage ratio leads to a positive impact on power consumption and leakage currents. The examination presented here is useful in the fabrication of stacked GAA NS MOSFETs.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

The underlying physical concept of computing out-of-time-ordered correlation (OTOC) is a significant new tool within the framework of quantum field theory, which now-a-days is treated as a measure of random fluctuations. In this paper, by following the canonical quantization technique we demonstrate a computational method to quantify the two different types of Cosmological auto-correlated OTO functions during the epoch when the non-equilibrium features dominates in Primordial Cosmology. In this formulation, two distinct dynamical time scales are involved to define the quantum mechanical operators arising from cosmological perturbation scenario. We have provided detailed explanation regarding the necessity of this new formalism to quantify any random events generated from quantum fluctuations in Primordial Cosmology. We have performed an elaborative computation for the two types of two-point and four-point auto-correlated OTO functions in terms of the cosmological perturbation field variables and its canonically conjugate momenta to quantify random auto-correlations in the non-equilibrium regime. For both the cases we found significantly distinguishable non-chaotic, but random behaviour in the OTO auto-correlations, which was not pointed before in this type of studies. Finally, we have also demonstrated the classical limiting behaviour of the mentioned two types of auto-correlated OTOC functions from the thermally weighted phase space averaged Poisson Brackets, which we found exactly matches with the large time limiting behaviour of the auto-correlations in the super-horizon regime of the cosmological scalar mode fluctuation.

Global pose refinement is a significant challenge within Simultaneous Localization and Mapping (SLAM) frameworks. For LIDAR-based SLAM systems, pose refinement is integral to correcting drift caused by the successive registration of 3D point clouds collected by the sensor. A divergence between the actual and calculated platform path characterizes this error. In response to this challenge, we propose a linear, parameter-free model, which uses a closed circuit for global trajectory corrections. Our model maps rotations to quaternions and uses Spherical Linear Interpolation (SLERP) for transitions between them. The intervals are established from the constraint set by the Least Squares (LS) method on rotation closure and are proportional to the circuit's size. Translations are globally adjusted in a distinct linear phase. Additionally, we suggest a coarse-to-fine pairwise registration method, integrating Fast Global Registration and Generalized ICP with multiscale sampling and filtering. The proposed approach is tested on three varied datasets of point clouds, including Mobile Laser Scanners and Terrestrial Laser Scanners. These diverse datasets affirm the model's effectiveness in 3D pose estimation with substantial pose differences and efficient pose optimization in larger circuits.

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

The paper deals with an electrothermal model of a thermoelectric converter dedicated to performing simulations of coupled thermal and electrical phenomena taking place in harvesting processes. The proposed model is used to estimate the electrical energy gain from waste heat that would be sufficient to supply electronic circuits, in particular autonomous battery-less nodes of wireless sensor networks (WSN) and Internet of Things (IoT) devices. The developed model is not limited to low power electronic solutions such as WSN or IoT; it can also be scaled up and applied to simulations of considerably higher thermal power conversion. In the paper, a few practical case studies are presented that show the feasibility and suitability of the proposed model for complex simultaneous simulation processes, in both electrical and thermal domains. The first example deals with a combined simulation of the electrothermal model of a thermoelectric generator (TEG) and an electronic harvester circuit based on Analog Devices’ power management integrated circuit LTC3108. The second example relates to the thermalization effect in heat sink-less harvesting applications that could be mitigated by a pulse mode operation.

Biological neural network (BNN) is the core brain for creature to accomplish its intelligent behaviors through unique network structure and mechanisms. It also inspires controlling human-designed autonomous agents including robots to generate more advanced intelligent behaviors by mimicking the neural control mechanism of creatures at a deeper and more interactive level. Here, we constructed a whole-brain neural network model of Caenorhabditis elegans (C. elegans), which characterizes the electrochemical processes at the level of cellular synapse. The neural network simulation integrates computational programming and visualization of neurons and synapse connections of C. elegans, containing the specific controllable circuits summarization with their dynamic characteristics within the whole network. To illustrate its particular intelligent control capability in terms of robotics, we introduce the first innovative methodology for applying the BNN model to a 12-legged robot’s movement control based on the established numerical simulation platforms. We accomplished and designed two methods and corresponding encoding processes, one involving orientation control and the other involving locomotion generation, to demonstrate the intelligent control performance of BNN. Both simulation and experiment results indicate that the robot exhibits stronger autonomy and more intelligent moving performance under the control of BNN. We then summarized the contributions for digitalizing the C. elegans’ whole-brain neural network in real-time and utilizing it to control robot in a closed loop to validate its advanced intelligence control ability in terms of a scientific robot.

Chaotic switching is a newly evolve randomization method which can suppress conducted electromagnetic interference generated within the DC-DC converter. It can suppress the spectral peaks present in the frequency band effectively by spread spectrum technique and can spread it over the wide range of frequency band implying EMI suppression. In this paper, a chaotic PWM technique based on RCFMFD scheme is generated through Field programmable gate array (FPGA) for suppressing the conducted electromagnetic interference (EMI) generated within the Luo converter. A hardware prototype of Luo converter was developed in order to analyze EMI reduction through FFT analysis by comparing both traditional periodic PWM switching and chaotic PWM switching. The results obtained from the hardware setup shows significant reduction of EMI with Chaotic switching as compared to traditional PWM switching for both boost and buck operation of Luo converter.

This study aims to focus on using the Volterra series and machine learning for forecasting random and chaotic wind speed regimes, since the calm weather is mostly noticed at the local site, making the dataset selection difficult. A novel method is proposed to predict Volterra kernels up to the third order, using a forward-back propagation neural network with 12-month measurements at Fujairah site (UAE). Both daily and monthly wind speed data sets are investigated for forecasting. The three dominant hourly and daily kernels are extracted for each day and each month. Predicted future Volterra kernels are estimated from past values using both statistical analysis and individual neuro networks for each of the Volterra kernel coefficients. Due to the random nature of wind speed at the local site, a two-layer with 4 neurons per layer neuro network is used to locate the most variable and intense speed during 8-hours in the day. Forecasted wind speed is determined with errors arising from different sources such as the utilization of only 3rd-order Volterra kernels and the difficulty of machine training of the employed shallow network. Nevertheless, this work depicts a useful algorithm to forecast chaotic and random wind speed regimes. Computational time is a trade of the complexity of Volterra mathematical analysis.

Borderline Personality Disorder (BPD) is a severe personality disorder whose neural bases are still unclear. Indeed, previous studies reported inconsistent findings concerning alterations in cortical and subcortical areas. In the present study we applied for the first time an unsupervised machine learning approach known as mCCA+jICA, in combination with a supervised machine learning approach known as Random Forest, to possibly find covarying GM-WM circuits that separate BPD from controls and that are also predictive of this diagnosis. To this aim, we analyzed the structural images of patients with BPD and matched HCs. Results showed that two GM-WM covarying circuits, including basal ganglia, amygdala, and portions of the temporal lobes and of the orbitofrontal cortex, correctly classified BPD against HC. Notably, these circuits are affected by specific child traumatic experiences (emotional and physical neglect, and physical abuse) and predict symptoms severity in the interpersonal and impulsivity domains. These results support that BPD is characterized by anomalies in GM and WM circuits related to early traumatic experiences and specific symptoms.

The out-of-time-ordered correlation (OTOC) function is an important new probe in quantum field theory which is treated as a significant measure of random quantum correlations. In this paper, with the slogan "Cosmology meets Condensed Matter Physics" we demonstrate a formalism using which for the first time we compute the Cosmological OTOC during the stochastic particle production during inflation and reheating following canonical quantization technique. In this computation, two dynamical time scales are involved, out of them at one time scale the cosmological perturbation variable and for the other the canonically conjugate momentum is defined, which is the strict requirement to define time scale separated quantum operators for OTOC and perfectly consistent with the general definition of OTOC. Most importantly, using the present formalism not only one can study the quantum correlation during stochastic inflation and reheating, but also study quantum correlation for any random events in Cosmology. Next, using the late time exponential decay of cosmological OTOC with respect to the dynamical time scale of our universe which is associated with the canonically conjugate momentum operator in this formalism we study the phenomena of quantum chaos by computing the expression for {\it Lyapunov spectrum}. Further, using the well known Maldacena Shenker Stanford (MSS) bound, on Lyapunov exponent, λ≤2π/β, we propose a lower bound on the equilibrium temperature, T=1/β, at the very late time scale of the universe. On the other hand, with respect to the other time scale with which the perturbation variable is associated, we find decreasing but not exponentially decaying behaviour, which quantifies the random correlation at out-of-equilibrium. Finally, we have studied the classical limit of the OTOC to check the consistency with the large time limiting behaviour.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.