Forward-bias hole injection from 10 nm-thick p-type Nickel Oxide layers into 10 um-thick n-type Gallium Oxide in a vertical NiO/Ga2O3 p-n heterojunction leads to more than a factor of 2 enhancement of photoresponse measured from this junction. While it takes only 600 seconds to obtain such a pronounced increase in photoresponse, it persists for hours, indicating feasibility of photovoltaic device performance control. The effect is ascribed to charge injection-induced increase of minority carrier (hole) diffusion length (resulting in improved collection of photogenerated non-equilibrium carriers) in n-type beta-Ga2O3 epitaxial layers, due to trapping of injected charge (holes) on deep meta-stable levels in the material and subsequent blocking of non-equilibrium carrier recombination through these levels. Suppressed recombination leads to increased non-equilibrium carrier lifetime, in turn determining a longer diffusion length and being the root-cause for the effect of charge injection.

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented by x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x = 3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

Abstract: This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x=3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

It has been known since the 1930’s that all immunoglobulins carry a weak negative charge in physiological solvents. However, there has been no systematic exploration of this fundamental property. Accurate charge measurements have been made using membrane confined electrophoresis in two solvents (pH 5.0 and pH 7.4) on a panel of twelve mAb IgGs, as well as their F(ab’)₂ and Fc fragments. The following observations were made at pH 5.0: 1) the measured charge differs from the calculated charge by ~40 for the intact IgGs, and by ~20 for the Fcs; 2) the intact IgG charge depends on both Fv and Fc sequences, but does not equal the sum of the F(ab)’₂ and Fc charge; 3) the Fc charge is consistent within a class. In phosphate buffered saline, pH 7.4: 1) the intact IgG charges ranged from 0 to -13; 2) the F(ab’)₂ fragments are nearly neutral for IgG1s and IgG2s, and about -5 for some of the IgG4s; 3) all Fc fragments are weakly anionic, with IgG1 < IgG2 < IgG4; 4) the charge on the intact IgGs does not equal the sum of the F(ab’)₂ and Fc charge. In no case is the calculated charge, based on H⁺ binding, remotely close to the measured charge. The charge on IgGs in physiological solvent is sufficiently small to minimize its contribution to thermodynamic nonideality. Some of the mAbs carried a charge in physiological salt that was outside the range observed for serum-purified human poly IgG. To best match physiological properties, a therapeutic mAb should have a measured charge that falls within the range observed for serum-derived human IgGs.

A major problem of the technological production process of the metallurgical-grade silicon is formation of a large amount of microsilica. However, this material can be a significant source of raw materials for its own production. Hence, this study is aimed to solve the problem of micro-silica utilization, i.e. the technogenic dust-like waste generated during the melting of the technical-grade silicon. Within this study, the technology of the joint briquetting of microsilica was investigated with the carbonaceous reducing agents, i.e. by obtaining of mono-charge and by melting of the technical-grade silicon from the obtained mono-charge in the 200kVA ore-thermal furnace. Results of the study show that the briquettes in the melting process of the technical-grade silicon can be used in the range from 0 to 50%. The using of briquettes may significantly improve the technological parameters. When briquetted charge is applied only, the technological parameters will deteriorate significantly. The material balance of silicon melting showed the recovery rates of the main elements (Si, Al, Ca and Fe). It recorded a decrease in content of aluminum from 1.9-2.1% to 0.5-0.7%, calcium from 0.2-0.3% to 0.07-0.1% and titanium from 0.2-0.23% to 0.11-0.13% during the transition to briquetted monocharge. Phosphorus content increased from 0.004-0.005 to 0.011-0.013%.

Continuing the investigation already started (See Farcaş, A.-A.; Bende, A. PCCP 2024, 26, 14937), the light absorption and charge-transfer properties of the dopamine (DA), dopamine zwitterion (called as dopamine-semi-quinone or DsQ) and dopamine-o-quinone (DoQ) adsorbed on the graphene nanoparticle surface have been investigated using the ground state and linear-response time-dependent density functional theories, considering the B97X-D3BJ/def2-TZVPP level of theory. In terms of the strength of molecular adsorption on the surface, the DsQ form has 50 % higher binding energy than that for the DA or DoQ cases (-20.24 kcal/mol vs. -30.41 kcal/mol). The results obtained for electronically excited states and UV-Vis absorption spectra show that the photochemical behavior of DsQ is more similar to DA than that observed for DoQ. Of the three systems analyzed, the DsQ-based complex showed the most active CT phenomenon, both in terms of the number of CT-like states and the amount of charge transferred. Of the first thirty electronically excited states computed for the DsQ case, eleven are purely CT-type and nine are mixed CT and localized (or Frenkel) excitations. By varying the adsorption distance between the molecule and the surface vertically, the amount of charge transfer obtained for DA decreases significantly as the distance increases, for DoQ it remains stable, while for DsQ there are states for which little change is observed, while for others there is a significant change. Furthermore, the mechanistic compilation of the electron orbital diagrams of the individual components cannot describe in detail the nature of the excitations inside the complex.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

In this paper, we propose an assumption of which the relation between electron and phonon is discussed and investigated based on the experiment of γ photon and electric interconverting with each other. We calculated the charge of a particular standing wave topology with Maxwell’s equation rotated in accordance space with the SO3 transformation. The derived charge value is 1.6035 × 10E−19C around 0.0826% different from the experimental data, indicating the proposal is a promising theory to explain the origin of charge and spin of electron particle. Electron spin angular momentum comes from the orbital angular momentum of photon rotation (electromagnetic field rotation), and electron charge comes from photon, that is, the space-time rotation effect of electromagnetic wave.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

A grand unification of electroweak and strong forces is presented based on a new idea called Unified Charged Vectors. Using this new concept, it is shown that: The electroweak and strong forces can be unified into a single electro-weak-strong force. The various charges and coupling constants of fermions (like the electroweak mixing angle) can be predicted, rather than presupposed. The Lagrangian symmetries can be predicted rather than presupposed. The standard model Lagrangian can be cast into a simple unified form.

This article will continue ansatz gage matrix of Iyer Markoulakis Helmholtz Hamiltonian mechanics points’ fields gage to Pauli Dirac monopole particle fields ansatz gage general formalism at Planck level, by constructing a Pauli Dirac Planck circuit matrix field gradient of particle monopole flow loop. This circuit assembly gage (PDPcag) that maybe operating at the quantum level, demonstrates the power of point fields matrix theoretical quantum general formalism of Iyer Markoulakis Helmholtz Hamiltonian mechanics transformed to Coulomb gage metrics, to form eigenvector fields of magnetic monopoles as well as electron positron particle gage metrics fields. Eigenvector calculations performed based on Iyer Markoulakis quantum general formalism are substituted for gage values of typical eigenvectors of dipolar magnetically biased monopoles with their conjugate eigenvectors, as well as eigenvector fields that are of the electron and positron particles. Then they are compiled to form combinatorial eigenvector matrix bundle of the monopole particle circuit field constructs assembly. Evaluation of this monopole particle fields matrix provided eigenvector fields results like SUSY, having Hermitian quantum matrix with electron-positron annihilation alongside north and south monopoles collapsing to dipolar “stable” magnetism, representing electromagnetic gaging typical metrics fields. Applying experimental observations on magnetic poles with measuring magnetic forces John Hodge’s results were showing asymmetrical pole forces; author has mathematically constructed asymmetric\strings\gage\metrics to characterize electromagnetic gravity, putting together while integrating with stringmetrics gravity that author has been reporting in earlier published articles. Physical Analysis with generalization of mass-charge and charge-fields gage metrics to quantum relativity gage metrics fields are proposed based on author’s proof formalism paper providing derivational algorithmic steps, to determine gage parametric values within the equation of Coulomb gage. Vortex fields’ wavefunctions and the scalar potential characterized by a function and a coupling constant having quantum density matrix together define the gage metrics quantifiable observable measurement physics of electron-positron cross-diagonal fields; contrastingly, diagonal terms of PDPcag matrix characterizes electron-positron particle eigenvector fields, while Hilbert Higgs mass metrics characterizes eigen-matter. Author is already working with Christopher O’Neill about magic square symmetry configurations to quantitatively understand symmetry, structure, and the real space geometry that are expected to form out of vacuum quanta point fields’ quantitative quantum general formalism theory of Iyer Markoulakis. In addition, author is currently collaborating with Manuel Malaver’s astrophysical Einstein Minkowski modified space time metrics evaluations of the sense-time-space relativistic general metrics to have means to account for curving or shaping of spacetime topology of a five-dimensional sense-time-space. Manuel Malaver’s specialization with modified Einstein Maxwell equations for modeling galaxies and stars cosmological physics, utilizing Einstein-Maxwell-Tolman- Schwarzschild and Reissner-Nordström spacetime and black holes theoretical formalisms have author of this paper collaboratively model quantum astrophysics of dark energy Star’s theory with Einstein-Gauss-Bonnet gravity equations.

Fatigue and dyspnea are the most commonly presented long-term complaints in individuals previously infected with SARS-CoV-2. The purpose of the study was to comprehensively evaluate diaphragm muscle function in COVID-19 survivors, as well as investigate whether potential diaphragm dysfunction will contribute to physical functioning impairment. 46 patients qualified to pulmonary rehabilitation were examined. Diaphragm muscle function parameters were evaluated using ultrasonography, while severity of dyspnea, aerobic capacity and amount of energy used by the body during physical activity were assessed by 6-minute walk test, mMRC scale and Metabolic Equivalent Task (MET), respectively. We identified 69.5% patients with diaphragm atrophy and 6.5% with diaphragm paralysis. Percentage of atrophy was not related to age, gender, BMI index, oxygen therapy use during COVID-19 infection course and severity of disease. Patients with presence of cough, fever and without loss of smell during COVID-19 course had a significantly greater values of diaphragm inspiratory thickness, while patients with cough and no smell disorders had a significantly lower percentage of diaphragm atrophy. Diaphragm functional parameters were strongly associated with selected variables of person's exercise tolerance, such as distance in 6-minute walk test, saturation level, fatigue and exertion in Borg scale. In conclusion, diaphragm muscle dysfunction is a serious long-term post-COVID aftermath and can be viewed as a major contributing factor of prolonged functional impairments.

The targeted compounds in this research, resveratrol analogs 1–14 were synthesized as mixtures of isomers by the Wittig reaction using heterocyclic triphenylphosphonium salts and various benzaldehydes. The planned compounds were those possessing the trans-configuration as the biologically active trans-resveratrol. The pure isomers were obtained by repeated column chromatography in various isolated yields depending on the heteroaromatic ring. It was found that butyrylcholinesterase (BChE) was more sensitive to the heteroaromatic resveratrol analogs than acetylcholinesterase (AChE), except for 6, the methylated thiophene derivative with chlorine, which showed equal inhibition toward both enzymes. Compounds 5 and 8 achieved the highest BChE inhibition with IC50 values of 22.9 and 24.8 μM, respectively. The same as with AChE and BChE, methylated thiophene subunits of resveratrol analogs showed better enzyme inhibition than unmethylated ones. Two antioxidant spectrophotometric methods, DPPH and CUPRAC, were applied to determine the antioxidant potential of new heteroaromatic resveratrol analogs. Molecular docking of these compounds was conducted to visualize the ligand-active site complexes' structure and identify the non-covalent interactions responsible for the complex's stability, which influence the inhibitory potential. As ADME properties are crucial in developing drug product formulations, they have also been addressed in this work. The potential genotoxicity is evaluated by in silico studies for all compounds synthesized.

Our knowledge of electricity is based on two parallel lines of research: one focusing on ‘charge’, the other on ‘electron’. The distinction is blurred. The difficulty is that the fundamental nature of elementary charge is unknown. Here I present evidence that charge is a resting electron and electron is a moving charge – one physical entity two behavioural identities. That is, charge is nonrelativistic electron and electron is relativistic charge. Charges obey the laws of static electricity (electrostatics); electrons obey the laws of moving electricity (electrodynamics). Whether positive or negative, a charge is ejected from the atom at tremendous speed, losing the characteristics of ‘a charge’ and gaining those of ‘an electron’. I conclude that an atom, hence nature in general, contains an equal number of positive and negative electrons, recognised at rest as opposite charges. This solves the mystery of the electron-positron numerical asymmetry. It means that static positions and negatrons (charges) play equivalent roles as subatomic building blocks of matter, revealing a new atomic structure.

The marine region of the Zhongjieshan Islands is an essential component and location for enhancement and release in Zhoushan Fishing Ground. The scientific assessment of the target species' ecological carrying capacity serves as the foundation for augmentation and release efforts. Based on data from the 2021-2022 survey of biological resources in the waters of Zhongjieshan islands, the Ecopath model was built to analyze the trophic structure, energy flow, and overall characteristics of the ecosystem, as well as the ecological carrying capacity of the main enhancement and releasing species, Larimichthys crocea and Sepiella maindroni. The ecosystem's functional groups had trophic levels ranging from 1 to 3.48, with an average energy transfer efficiency of 8.11% and total flow of 2125.905 t·km-2. The ratio of total primary output to total respiration is 1.713. Zhongjieshan Islands' ecosystem was currently at an embryonic stage. The ecological carrying capacity of Larimichthys crocea and Sepiella maindroni was calculated to be 0.2325 t·km-2 and 0.1617 t·km-2, separately or individually. Larimichthys crocea and Sepiella maindroni showed enormous potential for development and release. The findings offered essential data for ecological studies on the waters of Zhongjieshan Islands, as well as a reference for enhancement and release efforts in this area.

It is shown that if there exists in nature a pair of heavy elementary particles each with a charge equal to that of the proton and with mass energy , then their direct interaction gives rise to a spontaneous fractionation of the two charges into three pairs of elementary particles according to two equiprobable channels, one hadronic and one leptonic. The leptons and quarks produced are in agreement with the first generation of the Standard Model of matter. Fractionation suggests the relative abundances of the elementary particles, introducing some questions about the possibility of the real existence of a currently unknown particle and its role in the formation of an apparent matter-antimatter asymmetry in the universe.

Concerns regarding the safety of ethoxyquin (EQ) have gradually increased, highlighting the necessity of identifying safer and more effective antioxidants for use in animal feed. This study investigates the effects of a compound antioxidant (CA) as an alternative to ethoxyquin on feed oxidative stability, growth performance, antioxidant capacity, and intestinal health in broilers. A total of 351 one-day-old Arbor Acres Plus male broilers were randomly assigned to three treatments with nine replicates of 13 birds each. The experimental treatments included: CON group (basal diet), EQ group (basal diet + 200 g/ton EQ at 60% purity), and CA group (basal diet + 200 g/ton compound antioxidant, which comprises 18% butylated hydroxytoluene, 3% citric acid, and 1% tertiary butylhydroquinone). The experiment lasted for 21 days. Compared to the control group, supplementation with CA significantly reduced the acid value, peroxide value, and malondialdehyde content in the feeds after storage. Moreover, CA supplementation significantly decreased feed intake and the feed conversion ratio (FCR) without affecting weight gain of boilers, while also improving liver antioxidant capacity (increased T-AOC and SOD levels), intestinal antioxidant capacity (increased CAT, HO-1, and GPX7 protein expression), and enhancing the duodenal villus height-to-crypt depth ratio and jejunal villus height. Additionally, CA treatment reduced intestinal barrier permeability (decreased diamine oxidase activity and D-lactate levels), potentially by promoting the expression of Occludin, ZO-1, and Mucin2 protein. Furthermore, the addition of CA elevated the protein levels of NF-κB p50 along with its inhibitory factors, IκB and NF-κB p105, in the intestines of broilers, thereby enhancing immune regulatory capacity. This supplementation also led to an increased abundance of beneficial gut microorganisms, including Lactobacillus, Alistipes, Candidatus Arthromitus, and Turicibacter. In comparison to the EQ group, CA supplementation enhanced feed oxidative stability, decreased the FCR, and improved the intestinal morphology, barrier functions, and inflammatory status in broilers. These findings suggest that this compound antioxidant may serve as a healthier and more effective alternative to ethoxyquin.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

Optical backbone networks constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is a key factor influencing optical network performance, it is important to understand how topological and physical properties impact its behavior and to have the capability to estimate its value. In this context, we propose here a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with constrained routing techniques for traffic routing. As this type of routing can lead to traffic blocking, particularly due to the limitation on the number of wavelengths per fiber, we also propose a fiber assignment algorithm designed to deal with this problem. We apply this method to a set of randomly generated networks using a modified Waxman model, and for a network with 60 nodes, in a scenario without blocking, we obtain capacities of about 2.5 Pbit/s for a symbol rate of 64 Gbaud and about 5 Pbit/s for a symbol rate of 128 Gbaud. Remarkably, this duplication in the total network capacity is achieved by an increase in the total fiber length of only about 51%.

The increasing environmental awareness and carbon-storing capability of wood have amplified its relevance as a building material. The demand for high-quality wood species necessitates exploring alternative, underutilized wood sources due to limited forest areas and premium wood volume. Consequently, the veneer-based industry is considering lower-value hardwood species like grey alder, black alder, and aspen as substitutes for high-quality birch. Initially less appealing due to their lower density and mechanical properties, these species show promise through densification, which enhances their density, strength, and hardness. This study aims to enhance plywood screw withdrawal capacity and surface hardness by densifying low-density wood species and using them in plywood face veneer layers or all layers. The relationship between wood density, surface hardness, and screw withdrawal capacity of plywoods made of low-value species like aspen and black alder is examined. Experimental work with a pilot-scale veneer and plywood production line demonstrates improved surface hardness (65% and 93% for aspen and black alder, respectively) and screw withdrawal capacity (16% and 35% for aspen and black alder, respectively) in face veneer densified low-value hardwood plywood. This research highlights the potential of densified low-value wood species to meet construction requirements, expanding their practical applications.

Digital transformation provides new drivers for economic performance growth in enterprises, but can it further improve ESG performance and support sustainable development? Based on the perspective of resources and capabilities, this paper uses the relevant data of 1588 listed companies in strategic emerging industries from 2011 to 2021 to study the differential impact of digital transformation on enterprise ESG performance, and further tests the mediating role of absorptive capacity and the moderating role of regional digital level. The research results indicate that: firstly, digital transformation of enterprises can positively promote the improvement of ESG performance; Secondly, there are significant differences in the impact of digital transformation on the ESG performance of enterprises in terms of property rights and industry characteristics. The ESG performance of state-owned enterprises and high-end equipment manufacturing enterprises is more sensitive to digital transformation; Thirdly, absorptive capacity plays a mediating role between digital transformation and corporate ESG performance; Fourthly, the positive regulation of regional digital level promotes the ESG performance of enterprises through digital transformation. The research conclusion is based on a digital perspective, providing relevant insights for improving the ESG performance of strategic emerging industry enterprises and expanding their ESG development paths.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

N-acetyl-L-cysteine (NAC), a sulfhydryl-containing compound, is mainly used as a mucolytic and as an antidote for acetaminophen overdose. Flow injection and sequential injection systems were designed and optimized with the aim of providing precise, accurate and reliable flow methods for NAC determination in pharmaceuticals with very low sample and reagent consumption. Proposed methods are based on a redox reaction wherein NAC reduces a complex of Cu(II) and bathocuproine disulfonate (BCS) to orange [Cu(BCS)2]3– complex, which absorption was measured at λmax = 483 nm. The optimized FIA and SIA configuration yielded a linear calibration curve with correlation coefficients (R2 = 0.9999 and R2 = 0.9996) in the concentration range of 3.0 × 10–7 – 3.0 × 10–5 mol L–1 and analytical frequency of 120 h–1 for the FIA method and 4.0 × 10–7 – 4.0 × 10–5 mol L–1, at sampling rate 60 h–1 for the SIA method. The proposed flow methods were successfully applied for the determination of NAC in pharmaceutical products, as the results showed good agreement with the standard method prescribed by Pharmacopoeia. Recoveries were in the range from 98.4% to 101.9% for the FIA method and from 97.2% to 101.8% for the SIA method.

Africa, home to the world's second-largest population of approximately 1.3 billion, grapples with significant challenges in meeting its medical needs, particularly in accessing quality healthcare services and products. The continent faces a continuous onslaught of emerging infectious diseases, exacerbating the strain on its already fragile public health infrastructure. The emergence of SARS-Cov2 has further exposed the deficiencies in Africa's public health response, ranging from limited diagnostic capabilities to difficulties in vaccine distribution. Compounding these challenges is vaccine hesitancy, which is prevalent in many regions due to varying levels of understanding and trust regarding vaccines. The disparities in vaccine literacy across the continent stem from a complex interplay of factors, including low literacy rates and a history of medical exploitation and misinformation campaigns. These factors have led to a pervasive distrust in medical institutions and healthcare providers among certain African communities. Despite concerted efforts by national governments, private entities, and international partners to address these challenges and improve vaccine literacy, significant hurdles persist. This manuscript examines the current state of education in vaccinology and related sciences in Africa, as well as the continent's efforts to address educational needs in vaccine development and manufacturing. It evaluates initiatives aimed at strengthening vaccine education and literacy, highlighting successful approaches and ongoing challenges. By assessing the progress made and identifying remaining obstacles, this review offers insights into how Africa can enhance its capacity in vaccinology and accelerate its contributions to global health security.

Purpose To investigate the effects of intra-articular glenohumeral joint triamcinolone injection in treating secondary adhesive capsulitis after breast cancer surgery.Methods This study prospectively enrolled 37 participants, 22 of the breast cancer surgery group and 15 of the idiopathic group. All participants received intra-articular glenohumeral joint injection in the affected shoulder joint and received physiotherapy for 12 week. The clinical assessment evaluated before, and 1, 3, and 6 months after the intervention. The primary outcome was the change in the Shoulder Pain and Disability Index (SPADI).Results The total SPADI(%) in both groups showed significant decrease from baseline to 1, 3, and 6 months after the intervention. There was no significant difference in the differences of the total SPADI from baseline to 1, 3, and 6 months between two groups. However, the improvement in the SPADI pain subscale and the PROM of abduction at 3 and 6 months post-injection in the breast cancer group were inferior to the idiopathic group.Conclusion Intra-articular triamcinolone injection for adhesive capsulitis after breast cancer surgery significantly improved in significant improvements of pain, shoulder function and the PROM. The effects were similar to idiopathic adhesive capsulitis, but in the breast cancer surgery group, appropriate pain and ROM management and monitoring are required even 3 months after injection. With a standardized injection protocol, intra-articular triamcinolone injection could be an effective and safe treatment option for secondary adhesive capsulitis after breast cancer surgery.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

A careful examination of the fundamentals of electromagnetic theory shows that due to the underlying mathematical assumptions required for Stokes' Theorem, global charge conservation cannot be guaranteed in topologically non-trivial spacetimes. However, in order to break the charge conservation mechanism we must also allow the electromagnetic excitation fields D, H to possess a gauge freedom, just as the electromagnetic scalar and vector potentials $\varphi$ and A do. This has implications for the treatment of electromagnetism in spacetimes where black holes both form and then evaporate, as well as extending the possibilities for treating vacuum polarisation. Using this gauge freedom of D, H we also propose an alternative to the accepted notion that a charge passing through a wormhole necessarily leads to an additional (effective) charge on the wormhole's mouth.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

In the investment casting process, the pattern made of wax is obtained in a die for further formation of shell mold. This work investigates commercial pattern waxes fluidity with a newly developed injection fluidity test. A good correlation between wax fluidity and its viscosity is observed, which is different from metallic alloys, where the solidification behavior is more critical. The difference in investigated filled waxes fluidity can be associated with the type and amount of filler.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

Charge-dipole interactions are very common interactions among atoms and molecules, especially materials that can emit light or contain free charges. The second-order charge-dipole interactions, proportional to $\frac{1}{R^4}$, are stronger than the second-order dipole-dipole interactions or van der Waals interactions, proportional to $\frac{1}{R^6}$, at longer distances. In reality, there is more than one atom or charge; therefore, we focus on few-body charge-dipole interactions, such as charge-dipole-dipole interactions. Laser cooling and trapping allow us to study such interactions with much higher precision. In this article, charge-dipole interactions will be investigated in ultracold gases. To increase the interaction strength, we excite the ultracold atoms to highly excited states, Rydberg states. Here, we treat one Rydberg atom as a dipole, the excited electron and the ion core are the two poles of an electric dipole. Specifically, we study charge-atom interactions in ultracold Rydberg gases.

The gravitational charge should be the energy instead of mass. This modification will lead to some different results and the experiments to test are also presented. Especially, we propose a scheme to achieve the negative energy and gravitational repulsive force in the lab.

The antioxidant properties and polyphenol content of some selected aromatic plants grown in Greece were studied. Plants were refluxed with 60% methanol after acid hydrolysis. The phenolic substances were quantified by HPLC-DAD. The antioxidant capacity of the extracts was determined with the Rancimat test using sunflower oil as substrate. Free radical scavenging activity was measured using the stable free radical 1, 1-diphenyl-2-picrylhydrazyl (DPPH). Results were compared with standard BHT and ascorbic acid. Total phenol concentration of the extracts was estimated with Folin-Ciocalteu reagent using gallic acid as standard.

Background: Mental capacity is a fundamental aspect that enables patients to fully par-ticipate in various healthcare procedures. To assist healthcare professionals (HCPs) in assessing patients' capacity, especially in the mental health field, several standardized tools have been developed. These tools include the MacArthur Competence Assessment Tool for Treatment (MacCAT-T), the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR), and the Competence Assessment Tool for Psychiatric Advance Directives (CAT-PAD). The core dimensions explored by these tools include Understanding, Appreciation, Reasoning, and Expression of a choice. Objective: This meta-analysis aimed to investigate potential differences in deci-sion-making capacity within the healthcare context among groups of patients with bi-polar disorder (BD) and schizophrenia spectrum disorder (SSD). Methods: A systematic search was conducted on Medline/Pubmed, and Scopus. Addi-tionally, Google Scholar was manually inspected, and a manual search of emerging re-views and reference lists of the retrieved papers was performed. Eligible studies were specifically cross-sectional, utilizing standardized assessment tools, and involving pa-tients diagnosed with BD and SSD. Data from the studies were independently extracted and pooled using random-effect models. Hedges g was used as a measure for outcomes. Results: Six studies were identified, with three studies using the MacCAT-CR, two studies the MacCAT-T, and one the CAT-PAD. The participants included 189 individuals with BD and 324 individuals with SSD. The meta-analysis revealed that patients with BD performed slightly better, and the difference was statistically significant, compared to patients with SSD, particularly in the domain of Appreciation (ES=0.23, 95% CI: 0.01 to 0.04, p=0.037). There was no statistically significant difference between the two groups for Understanding (ES=0.09, 95% CI: - 0.10 to 0.27, p=0.352), Reasoning (ES=0.18, 95% CI: - 0.12 to 0.47, p=0.074), and Expression of a choice (ES = 0.23, 95% CI: - 0.01 to 0.48, p=0.60). In the sensitivity analysis, furthermore, when considering only studies involving patients in symptomatic remission, the difference for Appreciation also resulted in non-significant (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). (ES=0.21, 95% CI: -0.04 to 0.46, p=0.102). Conclusions: These findings indicate that there are no significant differences between patients with BD and SSD during remission phases, while differences are minimal during acute phases. The usefulness of standardized assessment of capacity at any stage of the illness should be considered, both for diagnostic-therapeutic phases and for research and advance directives. Further studies are necessary to understand the reasons for the overlap in capacity between the two diagnostic categories compared in this study.

Accurate estimation of livestock carrying capacity (LCC) and implementing an appropriate actual stocking rate (ASR) is key to sustainable management of grazing adapted alpine grassland ecosystems. Reliable determination of aboveground biomass is fundamental to these determinations. Peak aboveground biomass (AGBP) captured from satellite data at the peak of the growing season (POS) is widely used as a proxy for annual aboveground biomass (AGBA) to estimate LCC of grasslands. Here we demonstrate limitations of this approach and highlight the ability of POS in the estimation of ASR. We develop and trail new approaches that incorporate remote sensing phenology timings of grassland response to grazing activity, considering relations between biomass growth and consumption dynamics, in efforts to support more accurate and reliable estimation of LCC and ASR. Results show that based on averaged values from large-scale studies of alpine grassland on the Qinghai-Tibet Plateau (QTP), differences between AGBP and AGBA underestimate LCC by about 31%. Findings from a smaller-scale study that incorporate phenology timings into estimation of annual aboveground biomass reveal that Haibei alpine meadows were overgrazed by 11.5% during the study period from 2000-2005. The methods proposed can be extended to map grassland grazing pressure by predicting LCC and tracking ASR, thereby improving sustainable resource use in alpine grasslands.

Low temperature dielectric property of charge/orbital ordered manganite, Pr1-xCaxMnO3 for 0.40≤x≤0.50 is investigated systematically as a function of Ca-content, x. The Ca-content dependence of dielectric permittivity and dissipation factor exhibit distinct maxima around x=0.45. The overall dielectric response of charge ordered Pr1-xCaxMnO3 is dominated by polarization induced by polaron hopping and exhibits thermally activated relaxation behaviour. The dielectric relaxation behaviour over the investigated temperature range is analysed with the help of small polaron hopping model and as well as variable range hopping model. The estimated polaron parameters also display non-monotonic variation with x and exhibit broad minima between x=0.425-0.45. The observed results suggest that a modulation of checker board type charge ordering pattern in Pr1-xCaxMnO3 is possibly taking place in the Ca-content range of investigation 0.40≤x≤0.50.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

High-quality ionization injection methods for Wake Field Acceleration driven by lasers or charged beams (LWFA/PWFA) can be optimised so as to generate high-brightness electron beams with tuneable duration in the attosecond range. We present a model of the minimum bunch duration obtainable with low-emittance ionization injection schemes, by spotting the roles of the ionization pulse duration, of the wake field longitudinal shape and of the delay of the ionization pulse position with respect to the node of the accelerating field. The model is tested for the resonant multi-pulse ionization injection (ReMPI) scheme, showing that bunches having length of about 300as can be obtained with a ionization pulse having duration of 30fs FWHM

Injection molding is one of the most common and effective manufacturing processes used to produce plastic products and impacts industries around the world. However, injection molding is a complex process that requires careful consideration of several key control variables. These variables and how they are utilized greatly affect the resulting parts of any molding operation. The bounds of the acceptable values of each control process variable or CPV must be analyzed and delimited to ensure manufacturing success and produce injected molded parts efficiently and effectively. One such method in which the key CPV of an injection molding operation can be delimited is through the development of a process window. Once developed, operating CPV at values inside the boundaries of the window or region will allow for the consistent production of parts that comply with the desired performance measures (PM), promoting a stable manufacturing process. This work proposes a method to experimentally develop process windows and illustrates the methodology with a specific molding operation.

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

An important aspect of PET imaging in clinical application is the localization and detection of tumors and lesions by administering a predetermined amount of radiotracer. This allows for example, a detailed view of what is going inside the patient body in cellular level. The quality of PET image is strongly dependent on the amount of administrated radiotracer and the patient’s body parameters. As the amount of injection radiotracer increases, the quality of resulting image increases and the lesion detection efficiency increases. The PET examiner society recognizes that any dose of radiotracer is associated with some possible radiation risks. It can harmful to the patient if essential PET imaging session is not made due to fear of radiation risk. In order to ensure the highest quality diagnosis and the smallest radiation risk, the patient should receive the smallest amount of radiotracer that provide image with sufficient quality. Our study is focused on proposing an efficient PET simulation tool that predict the smallest possible amount of administrated radiotracer to provides the appropriate diagnostic information based on significant patient’s body parameters (weight, age) at fixed scanning to improve the clinical diagnostic process in term of tumor detecting and localization. We have built a model of particular PET scanner and model of patient based on real MRI image and digital anthropomorphic phantom of our region of interest (brain). We have performed Monte Carlo simulation for whole PET procedure with special parameter In evaluating stage, a dataset of 60 patient is used and 11 independent dose prediction simulation for each patient are performed. We conclude that our simulator perform a desirable and efficient prediction of injection radiotracer amount that optimizes the current clinical amount up to 28%. In addition, we found that the total injected radiotracer dosage for adult patients are mostly affected when considering patient weight rather than patient age.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

Financial capacity instruments are psychometric tools designed to evaluate individual decisional capacity based on financial decisions. As tests are complex and need special conditions for administration and evaluation, it is difficult to use them in daily geriatric clinics. Our scoping review objective was to evaluate existing financial capacity instruments from the perspective of simplicity and portability. We evaluated one English speaking knowledge database (Medline) using a dedicated MeSH terminology. The review yielded one independent instrument, The Semi-Structured Clinical Interview for Financial Capacity, that can be easy adapted for every-day clinical use. It is simple to understand and perform and do not need trained personnel for administration. It can be finalized in 15 minutes. Initially validated on 261 subjects (with different forms of cognitive impairment), it showed good accuracy and precision mainly in subjects with cognitive impairment. The test is less apt to detect early or fluctuating cognitive impairment. Simplicity, the main advantage of the test, allows gamification fact that increases portability. Familiar images (coins, money) that are used for performing simple tasks does not need complex translation and adaptation. In form of a game, the test is suitable for serial administration, increasing the chance for early capacity reduction detection. Results reflect a physician judgement related to the subjects’ capacity to understand and execute simple financial instructions and not financial proficiency scores. The main limitation of our review is that we investigated only one, English speaking, knowledge database. The scoping strategy generated a financial capacity instrument that can be used in geriatric clinics for early diagnostic of decisional capacity reduction. Further studies are needed to evaluate the reliability and validity of the test in conditions of serial administration and in populations having various financial experience.

The relentless challenges posed by the COVID-19 pandemic have placed immense pressure on densely populated regions, such as Hong Kong, particularly in the context of an aging population. The burgeoning demand for healthcare services has necessitated the optimization of resource al-location within healthcare systems. This research presents an innovative analytical queueing model specifically tailored to address the intricate gridlock dynamics prevalent in healthcare systems, with a focused application in the challenging landscape of COVID-19 management. Hong Kong, like numerous other regions, has experienced a demo-graphic transition leading to heightened healthcare demands. Traditional methodologies for scrutinizing gridlock issues in healthcare settings, including simulation models, often prove suboptimal within the context of sophisticated optimization frameworks. This study, however, delves into analytical queueing models, offering a more efficient and effective approach. These models have been underexplored, primarily due to the intricacies involved in modeling gridlock propagation within restricted capacity, a critical concern magnified by the COVID-19 pandemic. The novel Queueing Model introduced in this research incorporates the maintenance of queue capacities and topological aspects as exogenous parameters, rendering it exceptionally adaptable for diverse gridlock-related applications. This adaptability is especially pertinent to healthcare management during the COVID-19 crisis. The model meticulously integrates the concept of gridlock, furnishing a comprehensive comprehension of its origins and repercussions. Validation of this model involves rigorous comparison with established methodologies, exact results, and simulation data, consistently high-lighting its versatility and precision. By applying the model to healthcare management, we scrutinize the dynamics of patient flow within a Hong Kong hospital, placing specific emphasis on the critical issue of bed blockage, further exacerbated by the COVID-19 pandemic. The model's gridlock decomposition unearths the nuanced impact of bed blockage on distinct hospital units, addressing the imperative requirement for quantifying in-patient bed blockage within healthcare systems during a pandemic.

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

This article presents a novel approach to understanding the influence of electric Energy on space-time curvature. EFE actual calculations refer solely to gravitational charges. In this article, I expand them to include the electric charge with calculations carried specifically for electric charges, with exciting results. The article leverages the universal consistency of physical laws, applying the known effects of gravitational charges on space-time curvature to electric charges. The research focuses on calculating the specific impact of electric charges on space-time curvature, rooted in the principle that space-time curvature is omnipresent. The findings reveal that space-time curvature's alteration due to an electric charge is influenced by various factors, including the charge's location, magnitude, mass, density, associated electric field, and its motion through space-time. Notably, the conversion factor for electric charges differs from the conversion factor for gravitational charges. These insights significantly enhance our understanding of electromagnetism and general relativity, paving the way for a more profound comprehension of electric charges.

Almost all modern inorganic light-emitting diode (LED) designs are based on double heterojunctions (DHJs) whose structure and current injection principle have remained essentially unchanged for decades. Although highly efficient devices based on the DHJ design have been developed and commercialized for energy-efficient general lighting, the conventional DHJ design requires burying the active region (AR) inside a pn-junction. This has hindered the development of emitters utilizing nanostructured ARs located close to device surfaces such as nanowires or surface quantum wells. Modern DHJ III-N LEDs also exhibit resistive losses which arise from the DHJ device geometry. The recently introduced diffusion-driven charge transport (DDCT) emitter design offers a novel way to transport charge carriers to unconventionally placed ARs. In a DDCT device, the AR is located apart from the pn-junction and the charge carriers are injected into the AR by bipolar diffusion. This device design allows the integration of surface ARs to semiconductor LEDs and offers a promising method to reduce resistive losses in high power devices. In this work, we present a review of the recent progress in gallium nitride (GaN) based DDCT devices, and an outlook of potential DDCT has for opto- and microelectronics.

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

One-dimensional chain of core-shell pairs connected by ideal springs enables design of the metamaterial demonstrating the negative effective density and negative specific thermal capacity. We assume that the molar thermal capacity of the reported metamaterial is governed by the Dulong-Petit law in its high temperature limit. The specific thermal capacity depends of the density of the metamaterial; thus, it is expected to be negative, when the effective density of the chain is negative. The range of the frequencies enabling the effect of the negative thermal capacity is established. Dependence of the effective thermal capacity on the exciting frequency for various core/shell mass ratios is elucidated. The effective thermal capacity becomes negative in the vicinity of the local resonance frequency ω0 in the situation when the frequency ω approaches ω0 from above. The effect of the negative effective thermal capacity is expected in metals in the vicinity of the plasma frequency.

Purpose: The intervertebral disc is a leading avascular organ in the body that may gather nutrition through diffusion. It maintains homeostasis by the use of autophagy and apoptosis to survive in unfavorable conditions such as stress and mechanical force. Therefore, excessive force and stress beyond normal conditions may cause intervertebral disc degeneration. The purpose of this study was to examine which is the better method, either external fixator (EF) or saline injection (SI), for inducing autophagy and apoptosis-mediated nucleus pulposus (NP) cell death in the discs of rat tail’s. Methods: Sixteen, nine-weeks-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross Kirschner wires) for a period ofsix and twelve weeks. Treated discs were dissected to identify the participation of autophagy and apoptosis in intervertebral disc degeneration. For identification purposes, H&amp;E staining, Masson’s trichrome staining, and immunohistochemistry (IHC) for LC3, beclin-1, and P62 in addition to MMP-2, MMP-3, and TIMP-1 were performed. Furthermore, we performed real-time polymerase chain reaction (RT-PCR) to observe autophagy-related gene expression (beclin-1, LC3, and P62) and apoptosis-related gene expression (MMP-2, MMP-3, and TIMP-1). Results: TheEF group showed more insidious NP cell degeneration than the control (Ctrl) group. Degeneration was elevated with increasing compression duration of EF group, whereas the SI group could not distinguish the margin of annulus fibrosus (AF) and NP cells. LC3, beclin-1, and P62 showed the highest and lateral expression whilst MMP-2, MMP-3, and TIMP-1 showed up-regulated and central expression in both groups, although the SI group could not recognize the boundary between NP and AF cells. The EF group showed the highest autophagy-related gene expression whereas the SI group showed lower expression. In addition, the EF group showed more autophagy-accumulating materials than the SI group which elevated with increasing compression duration. Furthermore, the SI group induced the highest apoptotic gene expression, but the EF group showed the lowest expression. Conclusion: The EF method was better for studying autophagy and apoptosis because it enhanced intervertebral disc degeneration after compression, which is actively linked to autophagy and apoptosis. The degeneration process was elevated by increasing the compression duration, but SI could not distinguish AF and NP cell margins.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

Electric energy is one of the driving forces in every country. The supply of electrical energy continues to present various challenges, such as high costs associated with procuring raw materials for generation, sparsely populated areas that are not connected to the main grid, and the need for infrastructure to support generation and network delivery. These challenges have contributed to the growing adoption of renewable energy sources, particularly solar photovoltaics (PV).In this study, we have developed a practical method to assess the spatial PV potential in a selected urban area. The methodology combines data collected from an unmanned aerial vehicle (UAV) photogrammetry, Geographic Information System (GIS), and the energy output from three remote photovoltaic systems installed at different locations. The results obtained from this approach not only provide the energy generated per square meter, per year (kWh m-2 yr-1), but also provides a base to calculate the potential distance that electric cars could travel based on the energy generated. To illustrate the application of this method, two practical cases were selected: Senglea, Malta, and Munxar, Gozo. These examples highlight the versatility and effectiveness of our approach for evaluating and harnessing solar energy through photovoltaic panels in different contexts.

In this article, we analyze the thermodynamics, thermal fluctuations and quasi-normal modes of a torus-like charge AdS black hole. The parameters of a torus-like charged AdS black hole are its mass, electric charge, and cosmological constant. We used a torus-like charge AdS black hole to evaluate thermodynamics through thermal fluctuations and found that it significantly affected the corrected thermodynamic potentials. Black holes of larger radii are more stable and significant. The effect of thermal fluctuation has been investigated on the other thermodynamic potentials such as the Hemohltz free energy, Gibbs free energy, enthalpy, and specific heat, using the concept of corrected entropy. Finally, we use null geodesics to deal with quasi-normal modes. The null geodesics provide the photon sphere angular velocity and Lyapunov exponent, which are the real and imaginary components of the quasi-normal modes in the eikonal limit. With inceasing charge and photon radius, angular velocity reaches its maximum, similar to Lyapunov's exponent.

According to observations leptons are always produced in pairs. Both particles can be electrically charged, or just one, in which case the charged particle is accompanied by a particle specific neutrino. The period doubling process in nonlinear dynamical systems creates stable pair structures from the Planck units. The electron-positron pair is one of the stable structures, and the rest mass, electric charge and magnetic moment can be accurately calculated by the period doubling process. That the pair structure is stable means, that e.g., an electron and a positron are always born together. In the muon decay one of the pair is charged, while the other remains chargeless because there is only one charge available. It is suggested in this article that neutrino is the chargeless part of the lepton pair.

This Letter revisits the instability of jet produced by shaped charge. Scaling laws for shaped charge jet are derived by dimensional analysis. It shows that the scaling laws are universal when cross-sectional shrinkage rate is not included in the formulation.

To understand the mystery of final unification, in our earlier publications, we proposed that, 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions; and 2) There exists a strong interaction elementary charge (e_s) in such a way that, it's squared ratio with normal elementary charge is close to inverse of the strong coupling constant. In this context, starting from lepton rest masses to stellar masses, we have developed many interesting and workable relations. We noticed that, electroweak field seems to be operated by a primordial massive fermion of rest energy 585 GeV. It can be considered as the zygote of all elementary particles and galactic dark matter. Proceeding further, with a characteristic fermion-boson mass ratio of 2.27, quarks can be classified into quark fermions and quark bosons. Considering strong charge conservation and electromagnetic charge conservation, fractional charge quark fermions and quark bosons can be understood. Quark fermions that generate observable massive baryons can be called as Fluons. Quark bosons that generate observable mesons can be called as Bluons. By considering a new hadronic fermion of rest energy 103.4 GeV, rest masses of fluons and bluons can be estimated and there by baryon masses and meson masses can be estimated.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

Optical networks, characterized by using optical fibers as a transmission medium, constitute the fundamental infrastructure employed today by network operators to deliver services to users. As network capacity is one of the key factors influencing optical network performance, it is important to comprehend its limitations and have the capability to estimate its value. In this context, we revisit the concept of capacity from various perspectives, including channel capacity, link capacity, and network capacity, thus providing an integrated view of the problem. Hence, we review the fundamental concepts behind optical networks, along with the basic physical phenomena present in optical fiber transmission and provide methodologies for estimating the different types of capacities, mainly using simple formulations. In particular, we propose a method to evaluate the network capacity that relies on the optical reach to account for physical layer aspects, in conjunction with capacitated routing techniques for traffic routing. We apply this method to three reference networks and obtain capacities ranging from tens to hundreds of Terabits/s. Whenever possible, we also compare our results with published experimental data to understand how they relate.

To identify factors associated with interstitial lung disease (ILD) in patients with systemic sclerosis (SSc) and build an algorithm to better define this association, for a personalized application in clinical practice. Methods. 78 SSc patients underwent HRCT to assess ILD. Demographic, clinical and laboratory variables were collected, focusing on those associated either directly or indirectly with lung involvement. The discriminant value of each variable was determined using the operating characteristic curves (ROC) and included in a model to estimate the strength of ILD association in SSc. Results. Thirty-three (42.31%) patients showed ILD on HRCT. DLco, M-Borg, GERD-Q, and capillary density were significantly associated with the presence of ILD-SSc. A model including these variables had a coefficient of determination (R2) of 0.697. DLco had an AUC of 0.861 (p&lt;0.001) with a cut-off ≤72.3% (sensitivity 78.8%, specificity 91.1%, +LR 8.86). The m-Borg scale showed an AUC of 0.883 (p&lt;0.001) with a cut-off &gt;2 (sensitivity 84.8%, specificity 82.2%, +LR 4.77), GERD-Q had an AUC of 0.815 (p&lt;0.001) with a cut-off &gt;7 (sensitivity 72.7%, specificity 86.7%, +LR 5.45). The capillary density showed an AUC of 0.815 (p&lt;0.001) with a cut-off ≤4.78 (sensitivity 87.9%, specificity 68.9%, +LR 2.82). Based on the pre-test probability values, these four variables were applied to Fagan's nomogram to calculate the post-test probability of this association. Conclusions. Our study identified four associated clinical factors of ILD in SSc patients. Moreover, their inclusion in an algorithm for the post-test probability, tailored to the specific patients’ characteristics, significantly increases the ability to find out the presence of SSc-ILD.

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

The entropy and charge distributions have been calculated for a simple model of polyelectrolytes attached to the surface of DNA using a field-theoretic method that includes fluctuations to the lowest one-loop order beyond mean-field theory. Experiments have revealed correlation-driven behavior of DNA in charged solutions, including charge inversion and condensation. In our model, the condensed polyelectrolytes are taken to be doubly charged dimers of length comparable to the distance between sites along the phosphate chains. Within this lattice-gas model, each adsorption site is assumed to have either a vacancy or a positively-charged dimer attached with the dimer oriented either parallel or perpendicular to the double helix DNA chain. We find that the inclusion of the fluctuation terms decreases the entropy by ∼50% in the weak binding regime. There, the bound dimer concentration is low because the dimers are repelled from the DNA molecule, which competes with the chemical potential driving them from the solution to the DNA surface. Surprisingly, this decrease in entropy due to correlations is so significant that it overcompensates for the entropy increase at the mean field level, so that the total entropy is even lower than in the absence of interactions between lattice sites. As a bonus, we present a transparent exposition of the methods used that could be useful to students and others wishing to use this formulation to extend this calculation to more realistic models.

The apparent shape of the black hole shadow provides a full description of the spin, the inclination angle and the charge of a Kerr black hole, without any astrophysical process or underlying theory in the astrophysical process.

The general coupling between particle transport and ionization-recombination processes in hot plasma is considered on the key concept of equilibrium charge state (CS) transport. A theoretical interpretation of particle and CS transport is gained in terms of a two-dimensional (2D) Markovian stochastic (random) processes, a discrete 2D Fokker-Plank-Kolmogorov equation (in charge and space variables) and generalized 2D coronal equilibrium between atomic processes and particle transport. The basic tool for analysis of CS equilibrium and transport is the equilibrium cell (EC) (two states on charge and two on space), which presents (i) a unit phase volume, (ii) the characteristic scale of local equilibrium, (iii) a comprehensive solution for the simplest nonlinear relations between transport and atomic processes. The approach opens up new perspectives on transport studies: (i) the direct modelling of equilibrium and transport of impurity using the atomic data base, (ii) recovery of the complete recombination rate profile based on knowledge of density profiles and ionization rate profiles, (iii) the local transport analysis, based on the reduction of the equilibrium set to the single EC (in particular, central or edge), (iv) analysis of the reduced transport coefficients (diffusion and convection) on the density profile measurements.

The design of more efficient photosensitizers is a matter of great importance in the field of cancer treatment by means of photodynamic therapy. One of the main processes involved in the activation of apoptosis in cancer cells is the oxidative stress on DNA once a photosensitizer is excited by light. As a consequence, it is a matter of great relevance to investigate in detail the binding modes of the chromophore with DNA, and the nature of the electronically excited states that participate in the induction of DNA damage, for example, charge-transfer states. In this work, we investigate the electronic structure of the anthraquinone photosensitizer intercalated into a double-stranded poly(dG-dC) decamer model of DNA. First, the different geometric configurations are analyzed by means of classical molecular dynamics simulations. Then, the excited states for the most relevant poses of anthraquinone inside the binding pocket are computed by an electrostatic-embedding quantum mechanics/molecular mechanics approach, where anthraquinone and one of the nearby guanine residues are described quantum mechanically to take into account intermolecular charge-transfer states. The excited states are characterized as monomer, exciton, excimer and charge-transfer states based on the analysis of the transition density matrix, and each of these contributions to the total density of states and absorption spectrum is discussed in terms of the stacking interactions. These results are relevant as they represent the footing for future studies on the reactivity of anthraquinone derivatives with DNA and give insights on possible geometrical configurations that potentially favor the oxidative stress of DNA.

To further explore the bearing capacity and sustainable construction of vacuum drainage pipe (VDP) piles, field tests were carried out to compare and analyze the ultimate single pile bearing capacity, pile side friction and pile end resistance of ordinary piles and vacuum drainage pipe piles. The effect of the VDP pile on energy conservation and emission reduction in practical projects is discussed. The results shows that the VDP pile basically eliminated the soil squeeze and did not cause excessive relative displacement of pile and soil after vacuum consolidation. The VDP pile enhances pile side friction resistance, resulting in a 17.6% increase in ultimate bearing capacity compared to traditional piles. The VDP pile method can reduce carbon emissions by 31.4% compared to traditional methods. This study provides guidance for the production and design of VDP piles in the future and demonstrates their potential for energy conservation and emission reduction benefits compared to traditional methods.

Motivated by the way animals react in nature, we introduce a fully-connected neural-network model, which incorporates the external pattern presented to the system as a fundamental tool of the recognition process. In this new scenario, in the absence of this external field, memories are not attractors inside basins of attraction, as in usual attractor neural networks, although basins may be created according to the external pattern, thus allowing storing a much larger number of memories. The key point consists in calibrating the influence of the external pattern such as to cancel the noise generated by those memories not correlated with the external pattern.We illustrate how this proposal works by including this new contribution in the standard Hopfield model, showing a significant increase in its recognition capacity (typically by a factor $10^{2}$). As an additional feature of this model, we show its ability to react promptly to changes in the external environment, a crucial attribute of living beings. This procedure can be applied to a wide variety of neural-network models to increase considerably their recognition and reaction capabilities.

Propolis is a bee product widely used as a dietary supplement and included in sweets or baby foods due to its well-known antioxidant and nutritional properties that are directly correlated with its phenolic composition. For this reason, this study analysed the total contents of flavones and flavonols, flavanones and dihydroflavonols, and the antioxidant capacity by using the methods of ABTS and linoleic acid/β-carotene in 99 samples of propolis from Spain and Chile. A rapid method was developed for quantifying these parameters in raw propolis using near infrared (NIR) spectroscopy with an optical fibre probe of remote reflectance applied directly to the ground up sample. The models developed allow the determination of the total of flavones and flavonols (0-183 mg rutin/ g propolis), of the total of flavanones and dihydroflavonols (9-109 mg pinocembrin/ g propolis extract), and the antioxidant capacity by the ABTS method (0-3212 nmolesTrolox/ mg of propolis) and of linoleic acid/β-carotene (22-86% inhibition). The NIR spectroscopy models were applied in external validation to different samples of the calibration group, which led to the conclusion that the methods developed provide significantly identical data to the initial chemical data of reference.

Purpose: Intervertebral disc is a leading avascular organ in the body. Hence, it may utilize autophagy and apoptosis to alive in unfavorable condition like stress and mechanical force. But excessive force and stress is a key cause to intervertebral disc degeneration (IVDD). Purpose of this study is to identify, external fixator (EF) and saline injection (SI) may induce autopahgy and apoptosis mediated nucleus pulposus (NP) cells death in rat tail’s disc and which method is better for studying autophagy and apoptosis. Methods: Sixteen 9-week-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross kirschner wires) for 6 weeks and 12 weeks as well. Treated discs were dissected for checking out participation of autopahgy and apoptosis to intervertebral disc degradation (IVDD). For identifying them, we performed H&E staining, Masson’s trichrome staining, and Immunohistochemistry (IHC) for LC3, Beclin-1and P62 as well as MMP-2, MMP-3 and TIMP-1.Furthermore, we performed quantitative polymerase chain reaction (qPCR)to check out autophagy related gene expression (beclin-1, LC3 and P62) and apoptosis related gene expression (MMP-2, MMP-3 and TIMP-1) respectively. Results: More insidious nucleus pulposus (NP) cell degeneration was indentified in (EF) group than in (Ctrl) control group. And rate of degradation was elevated with increasing duration of compression, but SI group cannot distinguish the margin of AF and NP cells. Highest along with lateral expression was found for LC3, Beclin-1, and P62 of both groups. Up-regulated and central expression was observed for MMP-2, MMP-3 and TIMP-1 of both groups, although SI group cannot recognize the margin between NP and AF cells. Utmost autophagy related gene expression was identified in EF group than in SI group. Besides, maximum autophagy accumulating materials was found in EF group than in SI group. And it was amplified along with increasing the duration of compression. Highest, apoptotic gene expression was observed in SI group, whereas, EF group showed lowest expression. Conclusion: External fixator (EF) method was better to study autophagy and apoptosis because it enhanced IVDD after compression which is actively linked with autophagy and apoptosis. Degeneration process was conversely proportional along with duration of compression. On contrary, saline injection (SI) could not distinguish AF and NP cell border.

Over recent years, the swine industry has witnessed the withdrawal of antibiotics and continuous regulation of zinc and copper oxides in the early-life nutrition of piglets. Due to this development, alternative ingredients or additives from plant sources have been tremendously explored. Therefore, this study's objective was to evaluate the effect of dietary supplementation with tannins on weaned piglets’ growth performance, serum antioxidant capacity, and immune status using a meta-analysis approach. With only the inclusion of non-challenged weaned piglets, a total of 16 studies with parameters of interest were deemed eligible after a two-step screening process following a comprehensive literature search in the scientific databases of Web of Science, Scopus, ScienceDirect, PubMed, and Google Scholar. Two main categories of data, including the study’s characteristics and response variables (growth performance, serum antioxidant, and immune indices), were extracted. Applying the random-effects models, Hedges’ g effect size of supplementation with tannins was calculated using the R software to determine the standardized mean difference (SMD) at a 95% confidence interval. Sub-group analysis and meta-regression further explored heterogeneity (PSMD 0.05, I2 50%, n ≥10). Supplementation with tannin reduced average daily gain (p = 0.20) and feed conversion ratio (p 0.01); however, it increased average daily feed intake (p = 0.07) and final body weight (p 0.01). Meta-regression models indicated that tannin dosage and supplementation duration were directly associated with tannins' effectiveness on productive performance. In the serum, the concentration of glutathione peroxidase, superoxide dismutase, and total antioxidant capacity were elevated (p 0.01) in response to tannins supplementation, while malondialdehydes was reduced (p 0.01). Likewise, decreased immunoglobin A (p = 0.47) and increased immunoglobin M and G levels (p 0.01) were detected. In conclusion, dietary supplementation with tannins, particularly with chestnut and grape seed proanthocyanidins, increases the productivity of weaned piglets. At the same time, it is a possible nutritional strategy to mitigate oxidative stress and stimulate gut health. Thus, supplementing chestnut and grape seed proanthocyanidin tannins in the early phase of swine production could be used to alleviate the incidence of diarrhea.

Quercetin is a flavonoid with a low molecular weight that belongs to the human diet's phenolic phytochemicals and non-energy constituents. Quercetin has a potent antioxidant capacity, being able to capture Reactive Oxygen Species (ROS), reactive nitro-gen species (RNS), and Reactive Chlorine Species (ROC), which act as reducing agents by chelating transition metal ions. Its structure has five functional hydroxyl groups, which work as electron donors and are responsible for capturing free radicals. In addition to its antioxidant capacity, it was described different pharmacological properties of Quercetin, such as carcinostatic properties, antiviral, antihypertensive, anti-inflammatory, protection of Low-Density Lipoprotein (LDL) oxidation, and inhibi-tion of angiogenesis are developed in this review.

This paper has two objectives: the first, to analyze the mediating effect of teacher empowerment between innovation culture and innovation capacity, and between inclusive leadership and innovation capacity; the second, to analyze the moderating effects of the school context on the innovation capacity. Data were collected in a representative sample of secondary schools in Valencia, Spain. The research model adopted is structural equation modeling, using the partial least squares (PLS) technique. The model has confirmed that teacher empowerment mediates between innovation culture and innovation capacity and between inclusive leadership and the innovation capacity. It is found that the educational context does not moderate the relationships in the proposed analysis model. This paper emphasizes the role of teacher empowerment in educational innovation and extends the knowledge of culture and leadership in the school organization.

Porphyromonas gingivalis is the major pathogenic bacteria found in the subgingival plaque of patients with periodontitis, leading to neuroinflammation. The bacteria destroy periodontal tissue through its virulence factors which are retained in the bacteria’s outer membrane vesicles (OMV). The purpose of this study was to determine the real time effect of intraperitoneal in-jection of P. gingivalis OMV on the production and expression of inflammatory markers as well as histopathological changes in the central nervous system (CNS) of adult zebrafish. Fol-lowing the LD50 (21 µg of OMV), the zebrafish were injected intraperitoneally with 18 µg of OMV and control group with normal saline at 7 different time points. Brains of experimental zebrafish were dissected at desired time points for colorimetric assays, ELISA and histology. This study discovered that nitric oxide and PGE2 were significantly increased at 45 minutes while IL-1β and IL-6 were expressed at subsequent 12- and 24-hours. respectively. Histopatho-logical changes such as blood coagulation, astrocytosis, oedema, spongiosis, and necrosis were also observed between 6- and 24-hours. The two apoptotic enzymes, caspases 3 and 9 were not expressed at any time point. In summary, the OMV induced neuroinflammatory responses and histopathological changes in adult zebrafish were time point dependent

Climate change is an important threat to orchard production at Mediterranean basin. Diversification seems to be implemented at a farm level as an important strategy to face these challenges. This paper aims to analyse farmer’s perceptions on crop diversification as a way to enhance farm’s adaptive capacity in a context of current and future climate changes impacts. Our case study is focused in orchards growers from French department of Vaucluse recently diversifying their activities through pistachio (Pistacia vera L.). We did in-depth semi-structured farmers’ interviews in 2021. The results show that diversification is supposed to enhance 3 main components of farms adaptative capacity: (1) strengthening robustness through improvement of buffering capacities to climate impacts (trough robust and adapted plants), economic uncertainties (by exploring local/niche markets) and labour scarcity (by lowering workforce requirements and mechanization); (2) Learning by experimenting, monitoring and exchanging with pairs and advisors (3) Cope with change related with societal demands and helps to increase personal satisfaction. Finally, promote farm’s diversification can contribute to enhance farm’s adaptive capacity under climate change impacts.

The study evaluated potassium peroxymonosulfate (PPMS) efficacy against rifampicin-resistant Salmonella Infantis (rif-SI), Escherichia coli (E. coli), Salmonella Infantis (SI), Newcastle disease virus (NDV) and avian influenza virus (AIV). The assessment encompassed varied concentrations, organic material conditions, and exposure durations to comprehensively evaluate PPMS efficacy. Moreover, PPMS’s efficacy was tested on diverse carrier surfaces and clothing to evaluate its bactericidal and virucidal potential. At the recommended concentrations (1X), PPMS effectively inactivated all pathogens within 5 sec, except for NDV, which required 30 sec in the presence of organic materials. At 0.5X, PPMS successfully inactivated E. coli, AIV and NDV within 5 sec in the absence of organic material. However, rif-SI and SI necessitated 30 sec for inactivation. Most pathogens were inactivated within 30 sec, with the exception for AIV, which was inactivated within 5 sec. PPMS effectively eliminated rif-SI on all carriers within 30 sec. Moreover, at both concentrations, PPMS successfully inactivated AIV on all carriers within 30 sec, except on stainless steel at 0.5X. Furthermore, PPMS at both concentrations required 5 and 30 sec, respectively, to inactivate AIV on the rayon sheet. Therefore, due to its demonstrated efficacy against a wide range of pathogens across diverse surfaces, PPMS emerges as a crucial alternative disinfectant significantly enhancing biosecurity on and around chicken farms. found in and around animal farms, slaughterhouses, and hospitals.

Microbiome research has gained considerable interest due to the emerging evidence of its impact on human and animal health. Similar to higher organisms, the gut-associated microbiota of mosquitoes affect host fitness and other phenotypes. It is now well established that microbes can alter pathogen transmission in mosquitoes, either positively or negatively, and avenues are being explored to exploit microbes for vector control. However, less attention has been paid to how microbiota affect phenotypes that impact vectorial capacity. Several mosquito and pathogen components, such as vector density, biting rate, survival, vector competence and pathogen extrinsic incubation period all influence pathogen transmission. Interestingly, the mosquito gut-associated microbes can impact each of these components, and therefore ultimately modulate vectorial capacity. Promisingly, this expands the options available to exploit microbes for vector control by also targeting parameters that affect vectorial capacity. However, there are still many knowledge gaps in the biology of the mosquito – microbe symbiosis that need to be addressed in order to understand these interactions more thoroughly and exploit them efficiently. Here, we review current evidence of the impacts of the microbiome on aspects of vectorial capacity highlighting opportunities for novel vector control strategies and areas where further studies are required.

Elastic peak electron spectroscopy, abbreviated EPES, involves ana- lyzing the line shape found in the elastic peak. The reduction in the energy of electrons of the elastic peak is a result of energy transfer to the target atoms, a phenomenon known as recoil energy. EPES differs from other electron spectroscopies in its unique ability to identify hydrogen in polymers and hydrogenated carbon-based materials. This feature is particularly noteworthy because lighter elements exhibit stronger energy shifts. The energy difference between the positions of the elastic peak of carbon and the elastic peak of hydrogen tends to increase as the kinetic energy of the incident electrons increases. If, during electron irradiation of an insulating polymer, the number of secondary electrons emitted by the surface is less than the number of electrons absorbed in the sample, the surface floats energetically until it stabilizes at a potential energy eVs. As a result, the interaction energy changes and modifies the energy difference between the elastic peaks of hydrogen and carbon. In this study, the charge effects are evaluated using the Monte Carlo method to simulate the EPES spectra of electrons interacting with polystyrene and polyethylene.

This work addresses the role of charge regulation (CR) and the associated fluctuations in the conformational and mechanical properties of weak polyelectrolytes. Due to CR, changes in the pH-value modifies the average macromolecular charge and conformational equilibria. A second effect is that, for a given average charge per site, fluctuations can alter the intensity of the interactions by means of correlation between binding sites. We investigate both effects by means of Monte Carlo simulations at constant pH-value, so that the charge is a fluctuating quantity. Once the average charge per site is available, we turn off the fluctuations by assigning the same average charge to every site. A constant charge MC simulation is then performed. We make use of a model which accounts for the main fundamental aspects of a linear flexible polyelectrolyte i.e. proton binding, angle internal rotation, bond stretching and bending. Steric excluded volume and differentiated treatment for short-range and long-range interactions are also included in the model. It can be regarded as a kind of "minimal'' model in the sense that contains a minimum number of parameters but still preserving the atomistic detail. It is shown that, if fluctuations are activated, gauche state bond probabilities increase, and the persistence length decreases, so that the polymer becomes more folded. Macromolecular stretching is also analyzed in presence of CR (the charge depends on the applied force) and without CR (the charge is fixed to the value at zero force). The analysis of the low force scaling behavior concludes that Pincus exponent becomes pH-dependent. Both with and without CR, a transition from 1/2 at high pH-values (phantom chain) to 3/5 to low pH-values (Pincus regime), is observed. Finally, the intermediate force stretching regime is investigated. It is found that CR induces a moderate influence in the force-extension curves and persistence length (which in this force regime becomes force-dependent). It is thus concluded that the effect of CR on the stretching curves is mainly due to changes in the average charge at zero force. It is also found that, for the cases studied, the effect of steric excluded volume is almost irrelevant compared to electrostatic interactions.

An increasing body of evidence shows that seaweeds, including kelp, can be used as a tool to neutralize or remove excess nutrients and metals from the water column. Here we report on a preliminary field assessment showing potential nutrient and carbon removal differences by sugar kelp and ribbon kelp grown in common gardens. Seawater and tissue samples were collected systematically from two farms in Alaska. Results show differences between % N and % C content between ribbon kelp (Alaria marginata) and sugar kelp (Saccharina latissima). Results also show that tissue nitrogen in ribbon kelp varies sharply due to nitrogen availability in the water column. In contrast, the percentage of tissue N in sugar kelp remains comparatively stable. Our outcomes provide insight into potential differences in nutrient removal and harvest timing for different kelp species.

A recent study published in Nature Medicine (Mautner et al., Nat Med 2023 Nov 2. doi: 10.1038/s41591-023-02632-w. Epub ahead of print) reported findings regarding a four-arm parallel, multicenter, single-blind, randomized, controlled clinical trial with 480 patients, aimed at comparing the therapeutic effectiveness of orthobiologic interventions against corticosteroid injections for the treatment of knee osteoarthritis (OA). The study concluded that, one-year post-treatment, all orthobiologic therapies examined were equivalent in effectiveness to each other and to corticosteroid injections. While we commend the scope and methodological rigor of the trial, the publication could be enhanced by a more comprehensive presentation of data to support the conclusions drawn. Particularly, the omission of baseline data for primary outcomes, the missing context to evaluate absolute values, the lack of discussion regarding interindividual variability, and the unexpectedly favorable results for corticosteroids that contrast the established literature, are areas that merit additional examination and insight. Here we aim to highlight these points for consideration, and advocate for the release of supplementary data to facilitate a comprehensive understanding and utilization of this rich dataset.

The influence of various energetic particles and electron injection on transport of minority carriers and non-equilibrium carrier recombination in Ga₂O₃ is summarized in this review. In Ga₂O₃ semiconductor, if robust p-type material and bipolar structures become available, diffusion length of minority carriers will be of critical significance. Diffusion length of minority carriers dictates functionality of such electronic devices as diodes, transistors, and detectors. One of the problems in ultra-wide band gap materials technology, is the short carrier diffusion length, due to scattering on extended defects. Electron injection in n- and p-type Gallium Oxide results in a significant increase of the diffusion length, even after its deterioration due to exposure to alpha- and proton-irradiation. Furthermore, post electron injection diffusion length in irradiated material exceeds that in Ga₂O₃ prior to irradiation and injection. The root cause of the electron injection-induced effect is attributed to the increase of minority carrier lifetime in the material due to trapping of non-equilibrium electrons on native point defects. It is, therefore, concluded that the electron injection is capable of “healing” the adverse impact of radiation in Ga₂O₃ and can be used for control of minority carrier transport and, therefore, device performance.

With the popularization of natural gas and the requirements for environmental protection, the development and utilization of natural gas is particularly important. The status of natural gas in China's oil and gas exploration and development is constantly improving, and the country is paying more and more attention to the exploitation and utilization of natural gas. The Upper Paleozoic tight sandstone in the Ordos Basin is characterized by low porosity, low permeability and large area of concealed gas reservoirs. By injecting CO2 into the formation, the recovery of natural gas can be improved, and at the same time, the stable storage of CO2 can be achieved to achieve a win-win situation of CO2 emission reduction and utilization. Injecting greenhouse gas CO2 into gas reservoirs for storage and improving recovery has also become a hot research issue. In order to improve the recovery efficiency of tight sandstone gas reservoir, this paper takes the complex tight sandstone of Upper Paleozoic in Ordos Basin as the research object, through indoor physical simulation experiments, carried out the influence of displacement rate, fracture dip angle, core permeability, core dryness and wetness on CO2 gas displacement efficiency and storage efficiency, and analyzed the influence of different factors on CO2 gas displacement efficiency and storage efficiency to improve the recovery and storage efficiency. The research results show that under different conditions, when the CO2 injection pore volume is less than 1PV, the relationship between the CH4 recovery rate and the CO2 injection pore volume is linear, and the tilt angle is 45 °. When the CO2 injection pore volume exceeds 1PV, the CH4 recovery rate increases slightly with the increase of displacement speed, the recovery rate of CO2 displacement CH4 is between 87% - 97%, and the CO2 breakthrough time is 0.7PV-0.9PV. In low-permeability and low-speed displacement cores, the diffusion of CO2 molecules is more significant. The lower the displacement speed is, the earlier the breakthrough time of CO2 is, and the final recovery of CH4 slightly decreases. Gravity has a great impact on CO2 storage and enhanced recovery. The breakthrough of high injection and low recovery of CO2 is earlier, and the recovery of CH4 is about 3.3% lower than that of low injection and high recovery. The bound water makes the displacement phase CO2 partially dissolved in the formation water, and the CO2 breakthrough lags about 0.1PV. Ultimately, CH4 recovery factor and CO2 storage rate are higher than those of dry core displacement. The research results provide theoretical data support for CO2 injection to improve recovery and storage efficiency in complex tight sandstone gas reservoirs.

Considerable amounts of agro-industrial by-products are discarded or burnt as fuel every year. However, they can be utilized as a valuable source of fiber, phenolics and other useful compounds such as antioxidants. The profile of beneficial compounds can be affected by genotype, locality, orchard management and productive season, adding or decreasing the bioactive potential of by-products. In this study, hazelnut (Corylus avellana L.) and walnut (Juglans regia L.) nutshells were investigated for their fiber content and antioxidant capacity as valorized by-products for the industry. Determinations (ORAC, TPC and color asses) were performed in hazelnut and walnut orchards located in Southern Chile during three consecutive seasons (2020/21; 2021/22 and 2022/23). Analyses of oxygen radical absorbance capacity (ORAC) in nutshells showed the highest ORAC from both species in the season 2020/21 (3217 µmol TE g1DW for hazelnut shells and 4663 µmol TE g DW1 for walnut shells), while variability in the consecutive seasons was lower for hazelnut than in walnut. Total phenolic content in hazelnut shells was positively correlated with L* (R: 0.883) and E (R: 0.924) during 2020/21 season, also with L* for 2022/23 (R: 0.907). While ORAC was negatively correlated with L* (R: 0.922) in 2021/22. In addition, morphological and structural features of both nutshells examined by Scavenging Electron Microscopy (VP-SEM) and Confocal Scavenging Laser Microscopy (CSLM) revealed differential tissue distribution and accumulation patterns of both cellulose and lignin. On the other hand, photo-colorimetric values were determined for both shells and corresponding seasons, and non-significative differences were found both shells and among seasons Finally, these results provide insight into the physicochemical characteristics of two shell types which should be considered together with antioxidant capacity in their valorization as a residual material.

This study investigated the effects of dietary garlic powder and fermented garlic powder supplementation at 1% and 2% levels on growth performance, digestive tract efficacy, blood biochemistry, immunity, and antioxidant status of Liza ramada (n=225 fish; 86.00±0.42 g) over a 60-day period. Fish fed diets supplemented with both forms of garlic at both levels exhibited significantly improved final body weight, weight gain, specific growth rate, and feed conversion ratio compared to the control group. Digestive enzyme activities (amylase, lipase, and protease) were significantly enhanced in all supplemented groups. Blood biochemical analysis revealed reduced glucose levels and increased total protein in garlic-supplemented groups, with no adverse effects on liver or kidney function markers. Immune parameters, including lysozyme activity, bactericidal activity against Streptococcus agalactiae, alternative complement pathway (ACP), and, respiratory burst (NBT) were significantly enhanced in garlic-supplemented groups, with fermented garlic showing more pronounced effects. Antioxidant enzyme activities (SOD, CAT, and GPx) were also significantly increased in all supplemented groups, particularly in those fed fermented garlic. No significant differences in survival rates were observed among treatments. The results suggest that both garlic powder and fermented garlic powder supplementation, especially at the 2% level, can effectively improve growth, feed utilization, immune function, and antioxidant status in L. ramada. Fermented garlic generally demonstrated superior effects, indicating its potential as a beneficial feed additive in aquaculture. Based on these findings, it is recommended to incorporate fermented garlic powder at a 2% level in L. ramada diets to optimize growth performance and health status. Further research is warranted to investigate the long-term effects and cost-effectiveness of this supplementation strategy in commercial aquaculture settings.

Evaluating new, promising organic molecules to make next-generation organic optoelectronic devices necessitates the evaluation of charge carrier transport performance through the semi-conducting medium. In this work, we utilize quantum chemical calculations (QCC) and kinetic Monte Carlo (KMC) simulations to predict the zero-field hole mobilities of ~100 morphologies of the benchmark polymer poly(3-hexylthiophene), with varying simulation volume, structural order, and chain-length polydispersity. Morphologies with monodisperse chains were generated previously using an optimized molecular dynamics force-field and represent a spectrum of nanostructured order. We discover that a combined consideration of backbone clustering and system-wide disorder arising from side-chain conformations are correlated with hole mobility. Furthermore, we show that strongly interconnected thiophene backbones are required for efficient charge transport. This definitively shows the role "tie-chains" play in enabling mobile charges in P3HT. By marrying QCC and KMC over multiple length- and time-scales, we demonstrate that it is now possible to routinely probe the relationship between molecular nanostructure and device performance.

Recently, deep neural networks (DNNs) have been widely used in various fields such as autonomous vehicles and smart homes. Since these DNNs can be directly implemented on edge devices, they offer advantages such as real-time processing in low-power and low-bandwidth environments. However, deployment of DNNs in embedded systems, including edge devices, exposes them to threats such as fault injection attacks. In this paper, we introduce two methods to induce misclassifications by using clock and voltage glitch-based fault attacks in devices where DNN models are executed. As a result of experiments on a microcontroller implemented with a DNN for image classification, we show that glitch injection attacks can lead with high probability to serious misclassifications. Furthermore, we propose a countermeasure to glitch attacks on the softmax function, and confirm that this method is effective in preventing misclassifications.

In this study, a modular multi-step photometric microflow injection analysis (micro-FIA) system for the automatic determination of Cu(II) in a bioreactor has been developed. The system incorporates diverse 3D-printed modules, including a platform formed by a mixer module to mix Cu(II) with hydroxylamine which reduces Cu(II) to Cu(I) linked to a diluter module via a Tesla valve, a chelation mixer module, a disperser module, and a detector module provided by a LED light source at λ= 455 nm and a light dependence resistor (LDR) as a light intensity detector. The system measures the color intensity resulting from the chelation between Cu(I) and neocuproine. The micro-FIA system has demonstrated good capability for automatic and continuous Cu(II) determination, in a wide range of Cu concentrations from 34 to 2000 mg L-1. The device exhibits a good repeatability (coefficient of variation below 2% across the concentration range), good reproducibility, and has an accuracy of around 100% between 600 to 1900 mg·L-1. Real samples were analyzed using both the micro-FIA system and an atomic absorption spectroscopy method, revealing no statistically significant differences. Additionally, a Tesla valve located before the detector substituted a 3-way solenoid valve, eliminating the need for moving parts.

This study presents a novel approach to enhance Large Language Models (LLMs) like Alpaca by dynamically integrating real-time information. This method addresses the issue of content hallucination and data relevancy by automatically collecting and integrating current data from credible sources into model prompts. Experiments show a significant improvement in accuracy and a decrease in content hallucination, with a manageable increase in response time. The research underscores the potential of real-time data integration in making LLMs more accurate and contextually relevant, setting a foundation for future advancements in dynamic data processing in AI.

This work focuses on forced combustion with regards to the relationship between vent mixer models and several injection locations in unheated supersonic flow. A plasma jet torch was used to ignite the hydrogen–air mixture in a laboratory-scaled combustor duct. The flow field of the combustion was visualized with pressure and gas-sampling measurements. The vent mixers indicate good dispersion characteristics of the mixture for both parallel and normal 1 injections. However, forced combustion is dominantly governed by the injection rate toward the plasma jet (hot source) because the combustible region is restricted under the cold main flow. For this reason, the parallel injection, which provides the hydrogen–air mixture directly toward the plasma jet, shows good combustion performance. The normal 1 injection interacted with the vent mixers and shows slightly good combustion performance. Lastly, the normal 2 injection is little affected by the vent mixers and has poor combustion performance.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

The prevention, mitigation and treatment of movement impairments, ideally, requires early diagnosis or identification. As the human movement system has physiological and functional redundancy, movement limitations do not promptly arise at the onset of physical decline. A such, prediction of movement limitations is complex: it is unclear how much decline can be tolerated before movement limitations start. Currently, the term ‘homeostatic reserve’ or ‘physiological reserve’ is used to refer to the redundancy of the human biological system, but these terms do not describe the redundancy in the muscle architecture of the human body. The result of functional redundancy is compensation. Although compensation is an early predictor of movement limitations, clear definitions are lacking and the topic is underexposed in literature. The aim of this article is to provide a definition of compensation and emphasize its importance. Compensation is defined as an alteration in the movement trajectory and/or altering muscle recruitment to complete a movement task. Compensation for capacity is the result of a lack in neuromusculoskeletal reserve, where reserve is defined as the difference between the capacity (physiological abilities of the neuromusculoskeletal system) and the task demand. Compensation for movement objectives is a result of a shift in weighting of movement objectives, reflecting changing priorities. Studying compensation in biomechanics requires altered protocols in experimental set-ups, musculoskeletal models that are not reliant on prescribed movement, and inclusion of alternative movement objectives in optimal control theory.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

This paper presents an improved SOC estimation method for lithium ion batteries in Electric Vehicles using Bayesian optimized feedforward network. This innovative bayesian optimized neural network method attempts to minimize a scalar objective function by extracting hyperpa-rameters (hidden neurons in both layers) using a surrogate model. Furthemore, the hyperparameters are built and data samples are trained and validated. The performance of the proposed deep learning neural network is evaluated. Two reasonable size data samples are ex-tracted from Panasonic 18650PF Li-ion Mendeley datasets that are used for training and valida-tion. RNN and LSTM neural network algorithms offer the common core property of retaining past information and/or hidden states for better SOC estimation. However, the feature of this pro-posed method is the inclusion of Bayesian optimization that chooses optimal double layer hidden neurons. Analysis of results shows that Bayesian optimized feedforward algorithm with average MAPE (0.20%) is the lowest and is the best selection compared with average MAPE for other five deep learning algorithms. In the last quarter of fuel gauge, where fuel anxiety is severe, feed-forward with Bayesian Optimization algorithm is still the best selection (with MAPE of 0.64%).

4-component relativistic atomic and molecular calculations are typically performed within the no-pair approximation where negative-energy solutions are discarded, hence the symmetry between electronic and positronic solutions is not considered. These states are however needed in QED calculations, where furthermore charge conjugation symmetry becomes an issue. In this work we shall discuss the realization of charge conjugation symmetry of the Dirac equation in a central field within the finite basis approximation. Three schemes for basis set construction are considered: restricted, inverse and dual kinetic balance. We find that charge conjugation symmetry can be realized within the restricted and inverse kinetic balance prescriptions, but only with a special form of basis functions that does not obey the right boundary conditions of the radial wavefunctions. The dual kinetic balance prescription is on the other hand compatible with charge conjugation symmetry without restricting the form of the radial basis functions. However, since charge conjugation relates solutions of opposite value of the quantum number κ, this requires the use of basis sets chosen according to total angular momentum j rather than orbital angular momentum ` . As a special case, we consider the free-particle Dirac equation, where the solutions of opposite sign of energy are related by charge conjugation symmetry. We note that there is additional symmetry in those solutions of the same value of κ come in pairs of opposite energy.