This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

Forward-bias hole injection from 10 nm-thick p-type Nickel Oxide layers into 10 um-thick n-type Gallium Oxide in a vertical NiO/Ga2O3 p-n heterojunction leads to more than a factor of 2 enhancement of photoresponse measured from this junction. While it takes only 600 seconds to obtain such a pronounced increase in photoresponse, it persists for hours, indicating feasibility of photovoltaic device performance control. The effect is ascribed to charge injection-induced increase of minority carrier (hole) diffusion length (resulting in improved collection of photogenerated non-equilibrium carriers) in n-type beta-Ga2O3 epitaxial layers, due to trapping of injected charge (holes) on deep meta-stable levels in the material and subsequent blocking of non-equilibrium carrier recombination through these levels. Suppressed recombination leads to increased non-equilibrium carrier lifetime, in turn determining a longer diffusion length and being the root-cause for the effect of charge injection.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

It has been known since the 1930’s that all immunoglobulins carry a weak negative charge in physiological solvents. However, there has been no systematic exploration of this fundamental property. Accurate charge measurements have been made using membrane confined electrophoresis in two solvents (pH 5.0 and pH 7.4) on a panel of twelve mAb IgGs, as well as their F(ab’)₂ and Fc fragments. The following observations were made at pH 5.0: 1) the measured charge differs from the calculated charge by ~40 for the intact IgGs, and by ~20 for the Fcs; 2) the intact IgG charge depends on both Fv and Fc sequences, but does not equal the sum of the F(ab)’₂ and Fc charge; 3) the Fc charge is consistent within a class. In phosphate buffered saline, pH 7.4: 1) the intact IgG charges ranged from 0 to -13; 2) the F(ab’)₂ fragments are nearly neutral for IgG1s and IgG2s, and about -5 for some of the IgG4s; 3) all Fc fragments are weakly anionic, with IgG1 < IgG2 < IgG4; 4) the charge on the intact IgGs does not equal the sum of the F(ab’)₂ and Fc charge. In no case is the calculated charge, based on H⁺ binding, remotely close to the measured charge. The charge on IgGs in physiological solvent is sufficiently small to minimize its contribution to thermodynamic nonideality. Some of the mAbs carried a charge in physiological salt that was outside the range observed for serum-purified human poly IgG. To best match physiological properties, a therapeutic mAb should have a measured charge that falls within the range observed for serum-derived human IgGs.

The spectra and global distributions of the X-ray emissions generated by the solar wind charge-exchange (SWCX) process in the terrestrial magnetosheath are investigated based on a global hybrid model and a global geocoronal hydrogen model. The solar wind O6+ ions which are the primary charge state for oxygen ions in solar wind are considered. The line emissivity of the charge-exchange born O5+ ions are calculated by Spectral Analysis System for Astrophysical and Lab oratory (SASAL). It is found that the emission lines from the O5+ ranges from 105.607 to 118.291 eV with the strong line at 107.047 eV. We then simulated the magnetosheath X-ray emission intensity distributions with a virtual camera at two positions of north pole and dusk at six stages during the passing of a perpendicular interplanetary shock combined with a tangential discontinuity structure through the Earth’s magnetosphere. During this process, the X-ray emission intensity increases with time, and the maximum value is 27.11 keV cm-2 s-1 sr-1 on the dayside, which is 4.5 times that before the solar wind structure reaches the Earth. A clear shock structure can be seen in the magnetosheath and moves earthward. The maximum emission intensity seen at dusk is always higher than that seen at north pole.

In this paper, we propose an assumption of which the relation between electron and phonon is discussed and investigated based on the experiment of γ photon and electric interconverting with each other. We calculated the charge of a particular standing wave topology with Maxwell’s equation rotated in accordance space with the SO3 transformation. The derived charge value is 1.6035 × 10E−19C around 0.0826% different from the experimental data, indicating the proposal is a promising theory to explain the origin of charge and spin of electron particle. Electron spin angular momentum comes from the orbital angular momentum of photon rotation (electromagnetic field rotation), and electron charge comes from photon, that is, the space-time rotation effect of electromagnetic wave.

It is shown that if there exists in nature a pair of heavy elementary particles each with a charge equal to that of the proton and with mass energy , then their direct interaction gives rise to a spontaneous fractionation of the two charges into three pairs of elementary particles according to two equiprobable channels, one hadronic and one leptonic. The leptons and quarks produced are in agreement with the first generation of the Standard Model of matter. Fractionation suggests the relative abundances of the elementary particles, introducing some questions about the possibility of the real existence of a currently unknown particle and its role in the formation of an apparent matter-antimatter asymmetry in the universe.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

A grand unification of electroweak and strong forces is presented based on a new idea called Unified Charged Vectors. Using this new concept, it is shown that: The electroweak and strong forces can be unified into a single electro-weak-strong force. The various charges and coupling constants of fermions (like the electroweak mixing angle) can be predicted, rather than presupposed. The Lagrangian symmetries can be predicted rather than presupposed. The standard model Lagrangian can be cast into a simple unified form.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

Purpose To investigate the effects of intra-articular glenohumeral joint triamcinolone injection in treating secondary adhesive capsulitis after breast cancer surgery.Methods This study prospectively enrolled 37 participants, 22 of the breast cancer surgery group and 15 of the idiopathic group. All participants received intra-articular glenohumeral joint injection in the affected shoulder joint and received physiotherapy for 12 week. The clinical assessment evaluated before, and 1, 3, and 6 months after the intervention. The primary outcome was the change in the Shoulder Pain and Disability Index (SPADI).Results The total SPADI(%) in both groups showed significant decrease from baseline to 1, 3, and 6 months after the intervention. There was no significant difference in the differences of the total SPADI from baseline to 1, 3, and 6 months between two groups. However, the improvement in the SPADI pain subscale and the PROM of abduction at 3 and 6 months post-injection in the breast cancer group were inferior to the idiopathic group.Conclusion Intra-articular triamcinolone injection for adhesive capsulitis after breast cancer surgery significantly improved in significant improvements of pain, shoulder function and the PROM. The effects were similar to idiopathic adhesive capsulitis, but in the breast cancer surgery group, appropriate pain and ROM management and monitoring are required even 3 months after injection. With a standardized injection protocol, intra-articular triamcinolone injection could be an effective and safe treatment option for secondary adhesive capsulitis after breast cancer surgery.

This article will continue ansatz gage matrix of Iyer Markoulakis Helmholtz Hamiltonian mechanics points’ fields gage to Pauli Dirac monopole particle fields ansatz gage general formalism at Planck level, by constructing a Pauli Dirac Planck circuit matrix field gradient of particle monopole flow loop. This circuit assembly gage (PDPcag) that maybe operating at the quantum level, demonstrates the power of point fields matrix theoretical quantum general formalism of Iyer Markoulakis Helmholtz Hamiltonian mechanics transformed to Coulomb gage metrics, to form eigenvector fields of magnetic monopoles as well as electron positron particle gage metrics fields. Eigenvector calculations performed based on Iyer Markoulakis quantum general formalism are substituted for gage values of typical eigenvectors of dipolar magnetically biased monopoles with their conjugate eigenvectors, as well as eigenvector fields that are of the electron and positron particles. Then they are compiled to form combinatorial eigenvector matrix bundle of the monopole particle circuit field constructs assembly. Evaluation of this monopole particle fields matrix provided eigenvector fields results like SUSY, having Hermitian quantum matrix with electron-positron annihilation alongside north and south monopoles collapsing to dipolar “stable” magnetism, representing electromagnetic gaging typical metrics fields. Applying experimental observations on magnetic poles with measuring magnetic forces John Hodge’s results were showing asymmetrical pole forces; author has mathematically constructed asymmetric\strings\gage\metrics to characterize electromagnetic gravity, putting together while integrating with stringmetrics gravity that author has been reporting in earlier published articles. Physical Analysis with generalization of mass-charge and charge-fields gage metrics to quantum relativity gage metrics fields are proposed based on author’s proof formalism paper providing derivational algorithmic steps, to determine gage parametric values within the equation of Coulomb gage. Vortex fields’ wavefunctions and the scalar potential characterized by a function and a coupling constant having quantum density matrix together define the gage metrics quantifiable observable measurement physics of electron-positron cross-diagonal fields; contrastingly, diagonal terms of PDPcag matrix characterizes electron-positron particle eigenvector fields, while Hilbert Higgs mass metrics characterizes eigen-matter. Author is already working with Christopher O’Neill about magic square symmetry configurations to quantitatively understand symmetry, structure, and the real space geometry that are expected to form out of vacuum quanta point fields’ quantitative quantum general formalism theory of Iyer Markoulakis. In addition, author is currently collaborating with Manuel Malaver’s astrophysical Einstein Minkowski modified space time metrics evaluations of the sense-time-space relativistic general metrics to have means to account for curving or shaping of spacetime topology of a five-dimensional sense-time-space. Manuel Malaver’s specialization with modified Einstein Maxwell equations for modeling galaxies and stars cosmological physics, utilizing Einstein-Maxwell-Tolman- Schwarzschild and Reissner-Nordström spacetime and black holes theoretical formalisms have author of this paper collaboratively model quantum astrophysics of dark energy Star’s theory with Einstein-Gauss-Bonnet gravity equations.

Our knowledge of electricity is based on two parallel lines of research: one focusing on ‘charge’, the other on ‘electron’. The distinction is blurred. The difficulty is that the fundamental nature of elementary charge is unknown. Here I present evidence that charge is a resting electron and electron is a moving charge – one physical entity two behavioural identities. That is, charge is nonrelativistic electron and electron is relativistic charge. Charges obey the laws of static electricity (electrostatics); electrons obey the laws of moving electricity (electrodynamics). Whether positive or negative, a charge is ejected from the atom at tremendous speed, losing the characteristics of ‘a charge’ and gaining those of ‘an electron’. I conclude that an atom, hence nature in general, contains an equal number of positive and negative electrons, recognised at rest as opposite charges. This solves the mystery of the electron-positron numerical asymmetry. It means that static positions and negatrons (charges) play equivalent roles as subatomic building blocks of matter, revealing a new atomic structure.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

N-acetyl-L-cysteine (NAC), a sulfhydryl-containing compound, is mainly used as a mucolytic and as an antidote for acetaminophen overdose. Flow injection and sequential injection systems were designed and optimized with the aim of providing precise, accurate and reliable flow methods for NAC determination in pharmaceuticals with very low sample and reagent consumption. Proposed methods are based on a redox reaction wherein NAC reduces a complex of Cu(II) and bathocuproine disulfonate (BCS) to orange [Cu(BCS)2]3– complex, which absorption was measured at λmax = 483 nm. The optimized FIA and SIA configuration yielded a linear calibration curve with correlation coefficients (R2 = 0.9999 and R2 = 0.9996) in the concentration range of 3.0 × 10–7 – 3.0 × 10–5 mol L–1 and analytical frequency of 120 h–1 for the FIA method and 4.0 × 10–7 – 4.0 × 10–5 mol L–1, at sampling rate 60 h–1 for the SIA method. The proposed flow methods were successfully applied for the determination of NAC in pharmaceutical products, as the results showed good agreement with the standard method prescribed by Pharmacopoeia. Recoveries were in the range from 98.4% to 101.9% for the FIA method and from 97.2% to 101.8% for the SIA method.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

A careful examination of the fundamentals of electromagnetic theory shows that due to the underlying mathematical assumptions required for Stokes' Theorem, global charge conservation cannot be guaranteed in topologically non-trivial spacetimes. However, in order to break the charge conservation mechanism we must also allow the electromagnetic excitation fields D, H to possess a gauge freedom, just as the electromagnetic scalar and vector potentials $\varphi$ and A do. This has implications for the treatment of electromagnetism in spacetimes where black holes both form and then evaporate, as well as extending the possibilities for treating vacuum polarisation. Using this gauge freedom of D, H we also propose an alternative to the accepted notion that a charge passing through a wormhole necessarily leads to an additional (effective) charge on the wormhole's mouth.

Rising organic charge in northern freshwaters is attributed to increasing levels of Dissolved Natural Organic Matter (DNOM) and shifts in water chemistry. Organic charge concentration may be determined by charge balance calculations (Org.-) or modelled (OAN-) using the conceptual Oliver and Hruška models based on the density of weak acid functional sites (SD) present in DNOM. The charge density (CD) is governed by the SD and protonation and complexation reactions on the functional groups. The models use this SD as a key parameter in empirically fitting the model to Org.-. Utilizing extensive datasets of water chemistry, this study shows that spatial and temporal differences in SD and CD are influenced by variations in the humic-to-fulvic ratio of DNOM and the organic aluminum (Al) complexation, as well as the mole fraction of CD to SD governed by the acidity. Site median SD obtained for 44 long-term monitored acid-sensitive lakes was 11.1 and 13.9 µEq/mg C for the Oliver and the Hruška model, respectively. During the 34 years of monitoring the CD increased by 70%, likely due to rising pH and declining Al complexation with DNOM. Present-day median SD values for the Oliver and Hruška models in 16 low-order streams are 13.8 and 15.8 µEq/mg C, respectively, and 10.8 and 12.5 µEq/mg C, respectively, in 10 high order rivers.

In the investment casting process, the pattern made of wax is obtained in a die for further formation of shell mold. This work investigates commercial pattern waxes fluidity with a newly developed injection fluidity test. A good correlation between wax fluidity and its viscosity is observed, which is different from metallic alloys, where the solidification behavior is more critical. The difference in investigated filled waxes fluidity can be associated with the type and amount of filler.

The gravitational charge should be the energy instead of mass. This modification will lead to some different results and the experiments to test are also presented. Especially, we propose a scheme to achieve the negative energy and gravitational repulsive force in the lab.

In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Low temperature dielectric property of charge/orbital ordered manganite, Pr1-xCaxMnO3 for 0.40≤x≤0.50 is investigated systematically as a function of Ca-content, x. The Ca-content dependence of dielectric permittivity and dissipation factor exhibit distinct maxima around x=0.45. The overall dielectric response of charge ordered Pr1-xCaxMnO3 is dominated by polarization induced by polaron hopping and exhibits thermally activated relaxation behaviour. The dielectric relaxation behaviour over the investigated temperature range is analysed with the help of small polaron hopping model and as well as variable range hopping model. The estimated polaron parameters also display non-monotonic variation with x and exhibit broad minima between x=0.425-0.45. The observed results suggest that a modulation of checker board type charge ordering pattern in Pr1-xCaxMnO3 is possibly taking place in the Ca-content range of investigation 0.40≤x≤0.50.

High-quality ionization injection methods for Wake Field Acceleration driven by lasers or charged beams (LWFA/PWFA) can be optimised so as to generate high-brightness electron beams with tuneable duration in the attosecond range. We present a model of the minimum bunch duration obtainable with low-emittance ionization injection schemes, by spotting the roles of the ionization pulse duration, of the wake field longitudinal shape and of the delay of the ionization pulse position with respect to the node of the accelerating field. The model is tested for the resonant multi-pulse ionization injection (ReMPI) scheme, showing that bunches having length of about 300as can be obtained with a ionization pulse having duration of 30fs FWHM

Injection molding is one of the most common and effective manufacturing processes used to produce plastic products and impacts industries around the world. However, injection molding is a complex process that requires careful consideration of several key control variables. These variables and how they are utilized greatly affect the resulting parts of any molding operation. The bounds of the acceptable values of each control process variable or CPV must be analyzed and delimited to ensure manufacturing success and produce injected molded parts efficiently and effectively. One such method in which the key CPV of an injection molding operation can be delimited is through the development of a process window. Once developed, operating CPV at values inside the boundaries of the window or region will allow for the consistent production of parts that comply with the desired performance measures (PM), promoting a stable manufacturing process. This work proposes a method to experimentally develop process windows and illustrates the methodology with a specific molding operation.

Implementation of waterflood is with injected pressured water to reservoir to escalation oil production. Produced water is the dominated result from oil and gas mechanism in this world meanwhile 65% of water is injected back to the well for pressure maintenance, 30% for discharge aquifier condition and surface. For shaly sand, produced water usually bring coarse and suspended sand to the surface. Therefore, this sand level is needed to declining to avoid plugging in injection well until certain economic condition.

An important aspect of PET imaging in clinical application is the localization and detection of tumors and lesions by administering a predetermined amount of radiotracer. This allows for example, a detailed view of what is going inside the patient body in cellular level. The quality of PET image is strongly dependent on the amount of administrated radiotracer and the patient’s body parameters. As the amount of injection radiotracer increases, the quality of resulting image increases and the lesion detection efficiency increases. The PET examiner society recognizes that any dose of radiotracer is associated with some possible radiation risks. It can harmful to the patient if essential PET imaging session is not made due to fear of radiation risk. In order to ensure the highest quality diagnosis and the smallest radiation risk, the patient should receive the smallest amount of radiotracer that provide image with sufficient quality. Our study is focused on proposing an efficient PET simulation tool that predict the smallest possible amount of administrated radiotracer to provides the appropriate diagnostic information based on significant patient’s body parameters (weight, age) at fixed scanning to improve the clinical diagnostic process in term of tumor detecting and localization. We have built a model of particular PET scanner and model of patient based on real MRI image and digital anthropomorphic phantom of our region of interest (brain). We have performed Monte Carlo simulation for whole PET procedure with special parameter In evaluating stage, a dataset of 60 patient is used and 11 independent dose prediction simulation for each patient are performed. We conclude that our simulator perform a desirable and efficient prediction of injection radiotracer amount that optimizes the current clinical amount up to 28%. In addition, we found that the total injected radiotracer dosage for adult patients are mostly affected when considering patient weight rather than patient age.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

This article presents a novel approach to understanding the influence of electric Energy on space-time curvature. EFE actual calculations refer solely to gravitational charges. In this article, I expand them to include the electric charge with calculations carried specifically for electric charges, with exciting results. The article leverages the universal consistency of physical laws, applying the known effects of gravitational charges on space-time curvature to electric charges. The research focuses on calculating the specific impact of electric charges on space-time curvature, rooted in the principle that space-time curvature is omnipresent. The findings reveal that space-time curvature's alteration due to an electric charge is influenced by various factors, including the charge's location, magnitude, mass, density, associated electric field, and its motion through space-time. Notably, the conversion factor for electric charges differs from the conversion factor for gravitational charges. These insights significantly enhance our understanding of electromagnetism and general relativity, paving the way for a more profound comprehension of electric charges.

Almost all modern inorganic light-emitting diode (LED) designs are based on double heterojunctions (DHJs) whose structure and current injection principle have remained essentially unchanged for decades. Although highly efficient devices based on the DHJ design have been developed and commercialized for energy-efficient general lighting, the conventional DHJ design requires burying the active region (AR) inside a pn-junction. This has hindered the development of emitters utilizing nanostructured ARs located close to device surfaces such as nanowires or surface quantum wells. Modern DHJ III-N LEDs also exhibit resistive losses which arise from the DHJ device geometry. The recently introduced diffusion-driven charge transport (DDCT) emitter design offers a novel way to transport charge carriers to unconventionally placed ARs. In a DDCT device, the AR is located apart from the pn-junction and the charge carriers are injected into the AR by bipolar diffusion. This device design allows the integration of surface ARs to semiconductor LEDs and offers a promising method to reduce resistive losses in high power devices. In this work, we present a review of the recent progress in gallium nitride (GaN) based DDCT devices, and an outlook of potential DDCT has for opto- and microelectronics.

Purpose: The intervertebral disc is a leading avascular organ in the body that may gather nutrition through diffusion. It maintains homeostasis by the use of autophagy and apoptosis to survive in unfavorable conditions such as stress and mechanical force. Therefore, excessive force and stress beyond normal conditions may cause intervertebral disc degeneration. The purpose of this study was to examine which is the better method, either external fixator (EF) or saline injection (SI), for inducing autophagy and apoptosis-mediated nucleus pulposus (NP) cell death in the discs of rat tail’s. Methods: Sixteen, nine-weeks-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross Kirschner wires) for a period ofsix and twelve weeks. Treated discs were dissected to identify the participation of autophagy and apoptosis in intervertebral disc degeneration. For identification purposes, H&amp;E staining, Masson’s trichrome staining, and immunohistochemistry (IHC) for LC3, beclin-1, and P62 in addition to MMP-2, MMP-3, and TIMP-1 were performed. Furthermore, we performed real-time polymerase chain reaction (RT-PCR) to observe autophagy-related gene expression (beclin-1, LC3, and P62) and apoptosis-related gene expression (MMP-2, MMP-3, and TIMP-1). Results: TheEF group showed more insidious NP cell degeneration than the control (Ctrl) group. Degeneration was elevated with increasing compression duration of EF group, whereas the SI group could not distinguish the margin of annulus fibrosus (AF) and NP cells. LC3, beclin-1, and P62 showed the highest and lateral expression whilst MMP-2, MMP-3, and TIMP-1 showed up-regulated and central expression in both groups, although the SI group could not recognize the boundary between NP and AF cells. The EF group showed the highest autophagy-related gene expression whereas the SI group showed lower expression. In addition, the EF group showed more autophagy-accumulating materials than the SI group which elevated with increasing compression duration. Furthermore, the SI group induced the highest apoptotic gene expression, but the EF group showed the lowest expression. Conclusion: The EF method was better for studying autophagy and apoptosis because it enhanced intervertebral disc degeneration after compression, which is actively linked to autophagy and apoptosis. The degeneration process was elevated by increasing the compression duration, but SI could not distinguish AF and NP cell margins.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

Electric energy is one of the driving forces in every country. The supply of electrical energy continues to present various challenges, such as high costs associated with procuring raw materials for generation, sparsely populated areas that are not connected to the main grid, and the need for infrastructure to support generation and network delivery. These challenges have contributed to the growing adoption of renewable energy sources, particularly solar photovoltaics (PV).In this study, we have developed a practical method to assess the spatial PV potential in a selected urban area. The methodology combines data collected from an unmanned aerial vehicle (UAV) photogrammetry, Geographic Information System (GIS), and the energy output from three remote photovoltaic systems installed at different locations. The results obtained from this approach not only provide the energy generated per square meter, per year (kWh m-2 yr-1), but also provides a base to calculate the potential distance that electric cars could travel based on the energy generated. To illustrate the application of this method, two practical cases were selected: Senglea, Malta, and Munxar, Gozo. These examples highlight the versatility and effectiveness of our approach for evaluating and harnessing solar energy through photovoltaic panels in different contexts.

In this article, we analyze the thermodynamics, thermal fluctuations and quasi-normal modes of a torus-like charge AdS black hole. The parameters of a torus-like charged AdS black hole are its mass, electric charge, and cosmological constant. We used a torus-like charge AdS black hole to evaluate thermodynamics through thermal fluctuations and found that it significantly affected the corrected thermodynamic potentials. Black holes of larger radii are more stable and significant. The effect of thermal fluctuation has been investigated on the other thermodynamic potentials such as the Hemohltz free energy, Gibbs free energy, enthalpy, and specific heat, using the concept of corrected entropy. Finally, we use null geodesics to deal with quasi-normal modes. The null geodesics provide the photon sphere angular velocity and Lyapunov exponent, which are the real and imaginary components of the quasi-normal modes in the eikonal limit. With inceasing charge and photon radius, angular velocity reaches its maximum, similar to Lyapunov's exponent.

According to observations leptons are always produced in pairs. Both particles can be electrically charged, or just one, in which case the charged particle is accompanied by a particle specific neutrino. The period doubling process in nonlinear dynamical systems creates stable pair structures from the Planck units. The electron-positron pair is one of the stable structures, and the rest mass, electric charge and magnetic moment can be accurately calculated by the period doubling process. That the pair structure is stable means, that e.g., an electron and a positron are always born together. In the muon decay one of the pair is charged, while the other remains chargeless because there is only one charge available. It is suggested in this article that neutrino is the chargeless part of the lepton pair.

This Letter revisits the instability of jet produced by shaped charge. Scaling laws for shaped charge jet are derived by dimensional analysis. It shows that the scaling laws are universal when cross-sectional shrinkage rate is not included in the formulation.

To understand the mystery of final unification, in our earlier publications, we proposed that, 1) There exist three atomic gravitational constants associated with electroweak, strong and electromagnetic interactions; and 2) There exists a strong interaction elementary charge (e_s) in such a way that, it's squared ratio with normal elementary charge is close to inverse of the strong coupling constant. In this context, starting from lepton rest masses to stellar masses, we have developed many interesting and workable relations. We noticed that, electroweak field seems to be operated by a primordial massive fermion of rest energy 585 GeV. It can be considered as the zygote of all elementary particles and galactic dark matter. Proceeding further, with a characteristic fermion-boson mass ratio of 2.27, quarks can be classified into quark fermions and quark bosons. Considering strong charge conservation and electromagnetic charge conservation, fractional charge quark fermions and quark bosons can be understood. Quark fermions that generate observable massive baryons can be called as Fluons. Quark bosons that generate observable mesons can be called as Bluons. By considering a new hadronic fermion of rest energy 103.4 GeV, rest masses of fluons and bluons can be estimated and there by baryon masses and meson masses can be estimated.

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

The entropy and charge distributions have been calculated for a simple model of polyelectrolytes attached to the surface of DNA using a field-theoretic method that includes fluctuations to the lowest one-loop order beyond mean-field theory. Experiments have revealed correlation-driven behavior of DNA in charged solutions, including charge inversion and condensation. In our model, the condensed polyelectrolytes are taken to be doubly charged dimers of length comparable to the distance between sites along the phosphate chains. Within this lattice-gas model, each adsorption site is assumed to have either a vacancy or a positively-charged dimer attached with the dimer oriented either parallel or perpendicular to the double helix DNA chain. We find that the inclusion of the fluctuation terms decreases the entropy by ∼50% in the weak binding regime. There, the bound dimer concentration is low because the dimers are repelled from the DNA molecule, which competes with the chemical potential driving them from the solution to the DNA surface. Surprisingly, this decrease in entropy due to correlations is so significant that it overcompensates for the entropy increase at the mean field level, so that the total entropy is even lower than in the absence of interactions between lattice sites. As a bonus, we present a transparent exposition of the methods used that could be useful to students and others wishing to use this formulation to extend this calculation to more realistic models.

The apparent shape of the black hole shadow provides a full description of the spin, the inclination angle and the charge of a Kerr black hole, without any astrophysical process or underlying theory in the astrophysical process.

The general coupling between particle transport and ionization-recombination processes in hot plasma is considered on the key concept of equilibrium charge state (CS) transport. A theoretical interpretation of particle and CS transport is gained in terms of a two-dimensional (2D) Markovian stochastic (random) processes, a discrete 2D Fokker-Plank-Kolmogorov equation (in charge and space variables) and generalized 2D coronal equilibrium between atomic processes and particle transport. The basic tool for analysis of CS equilibrium and transport is the equilibrium cell (EC) (two states on charge and two on space), which presents (i) a unit phase volume, (ii) the characteristic scale of local equilibrium, (iii) a comprehensive solution for the simplest nonlinear relations between transport and atomic processes. The approach opens up new perspectives on transport studies: (i) the direct modelling of equilibrium and transport of impurity using the atomic data base, (ii) recovery of the complete recombination rate profile based on knowledge of density profiles and ionization rate profiles, (iii) the local transport analysis, based on the reduction of the equilibrium set to the single EC (in particular, central or edge), (iv) analysis of the reduced transport coefficients (diffusion and convection) on the density profile measurements.

The design of more efficient photosensitizers is a matter of great importance in the field of cancer treatment by means of photodynamic therapy. One of the main processes involved in the activation of apoptosis in cancer cells is the oxidative stress on DNA once a photosensitizer is excited by light. As a consequence, it is a matter of great relevance to investigate in detail the binding modes of the chromophore with DNA, and the nature of the electronically excited states that participate in the induction of DNA damage, for example, charge-transfer states. In this work, we investigate the electronic structure of the anthraquinone photosensitizer intercalated into a double-stranded poly(dG-dC) decamer model of DNA. First, the different geometric configurations are analyzed by means of classical molecular dynamics simulations. Then, the excited states for the most relevant poses of anthraquinone inside the binding pocket are computed by an electrostatic-embedding quantum mechanics/molecular mechanics approach, where anthraquinone and one of the nearby guanine residues are described quantum mechanically to take into account intermolecular charge-transfer states. The excited states are characterized as monomer, exciton, excimer and charge-transfer states based on the analysis of the transition density matrix, and each of these contributions to the total density of states and absorption spectrum is discussed in terms of the stacking interactions. These results are relevant as they represent the footing for future studies on the reactivity of anthraquinone derivatives with DNA and give insights on possible geometrical configurations that potentially favor the oxidative stress of DNA.

Purpose: Intervertebral disc is a leading avascular organ in the body. Hence, it may utilize autophagy and apoptosis to alive in unfavorable condition like stress and mechanical force. But excessive force and stress is a key cause to intervertebral disc degeneration (IVDD). Purpose of this study is to identify, external fixator (EF) and saline injection (SI) may induce autopahgy and apoptosis mediated nucleus pulposus (NP) cells death in rat tail’s disc and which method is better for studying autophagy and apoptosis. Methods: Sixteen 9-week-old male Sprague–Dawley rat tails were treated with 0.9% saline and EF (two-cross kirschner wires) for 6 weeks and 12 weeks as well. Treated discs were dissected for checking out participation of autopahgy and apoptosis to intervertebral disc degradation (IVDD). For identifying them, we performed H&E staining, Masson’s trichrome staining, and Immunohistochemistry (IHC) for LC3, Beclin-1and P62 as well as MMP-2, MMP-3 and TIMP-1.Furthermore, we performed quantitative polymerase chain reaction (qPCR)to check out autophagy related gene expression (beclin-1, LC3 and P62) and apoptosis related gene expression (MMP-2, MMP-3 and TIMP-1) respectively. Results: More insidious nucleus pulposus (NP) cell degeneration was indentified in (EF) group than in (Ctrl) control group. And rate of degradation was elevated with increasing duration of compression, but SI group cannot distinguish the margin of AF and NP cells. Highest along with lateral expression was found for LC3, Beclin-1, and P62 of both groups. Up-regulated and central expression was observed for MMP-2, MMP-3 and TIMP-1 of both groups, although SI group cannot recognize the margin between NP and AF cells. Utmost autophagy related gene expression was identified in EF group than in SI group. Besides, maximum autophagy accumulating materials was found in EF group than in SI group. And it was amplified along with increasing the duration of compression. Highest, apoptotic gene expression was observed in SI group, whereas, EF group showed lowest expression. Conclusion: External fixator (EF) method was better to study autophagy and apoptosis because it enhanced IVDD after compression which is actively linked with autophagy and apoptosis. Degeneration process was conversely proportional along with duration of compression. On contrary, saline injection (SI) could not distinguish AF and NP cell border.

Elastic peak electron spectroscopy, abbreviated EPES, involves ana- lyzing the line shape found in the elastic peak. The reduction in the energy of electrons of the elastic peak is a result of energy transfer to the target atoms, a phenomenon known as recoil energy. EPES differs from other electron spectroscopies in its unique ability to identify hydrogen in polymers and hydrogenated carbon-based materials. This feature is particularly noteworthy because lighter elements exhibit stronger energy shifts. The energy difference between the positions of the elastic peak of carbon and the elastic peak of hydrogen tends to increase as the kinetic energy of the incident electrons increases. If, during electron irradiation of an insulating polymer, the number of secondary electrons emitted by the surface is less than the number of electrons absorbed in the sample, the surface floats energetically until it stabilizes at a potential energy eVs. As a result, the interaction energy changes and modifies the energy difference between the elastic peaks of hydrogen and carbon. In this study, the charge effects are evaluated using the Monte Carlo method to simulate the EPES spectra of electrons interacting with polystyrene and polyethylene.

This work addresses the role of charge regulation (CR) and the associated fluctuations in the conformational and mechanical properties of weak polyelectrolytes. Due to CR, changes in the pH-value modifies the average macromolecular charge and conformational equilibria. A second effect is that, for a given average charge per site, fluctuations can alter the intensity of the interactions by means of correlation between binding sites. We investigate both effects by means of Monte Carlo simulations at constant pH-value, so that the charge is a fluctuating quantity. Once the average charge per site is available, we turn off the fluctuations by assigning the same average charge to every site. A constant charge MC simulation is then performed. We make use of a model which accounts for the main fundamental aspects of a linear flexible polyelectrolyte i.e. proton binding, angle internal rotation, bond stretching and bending. Steric excluded volume and differentiated treatment for short-range and long-range interactions are also included in the model. It can be regarded as a kind of "minimal'' model in the sense that contains a minimum number of parameters but still preserving the atomistic detail. It is shown that, if fluctuations are activated, gauche state bond probabilities increase, and the persistence length decreases, so that the polymer becomes more folded. Macromolecular stretching is also analyzed in presence of CR (the charge depends on the applied force) and without CR (the charge is fixed to the value at zero force). The analysis of the low force scaling behavior concludes that Pincus exponent becomes pH-dependent. Both with and without CR, a transition from 1/2 at high pH-values (phantom chain) to 3/5 to low pH-values (Pincus regime), is observed. Finally, the intermediate force stretching regime is investigated. It is found that CR induces a moderate influence in the force-extension curves and persistence length (which in this force regime becomes force-dependent). It is thus concluded that the effect of CR on the stretching curves is mainly due to changes in the average charge at zero force. It is also found that, for the cases studied, the effect of steric excluded volume is almost irrelevant compared to electrostatic interactions.

A recent study published in Nature Medicine (Mautner et al., Nat Med 2023 Nov 2. doi: 10.1038/s41591-023-02632-w. Epub ahead of print) reported findings regarding a four-arm parallel, multicenter, single-blind, randomized, controlled clinical trial with 480 patients, aimed at comparing the therapeutic effectiveness of orthobiologic interventions against corticosteroid injections for the treatment of knee osteoarthritis (OA). The study concluded that, one-year post-treatment, all orthobiologic therapies examined were equivalent in effectiveness to each other and to corticosteroid injections. While we commend the scope and methodological rigor of the trial, the publication could be enhanced by a more comprehensive presentation of data to support the conclusions drawn. Particularly, the omission of baseline data for primary outcomes, the missing context to evaluate absolute values, the lack of discussion regarding interindividual variability, and the unexpectedly favorable results for corticosteroids that contrast the established literature, are areas that merit additional examination and insight. Here we aim to highlight these points for consideration, and advocate for the release of supplementary data to facilitate a comprehensive understanding and utilization of this rich dataset.

The influence of various energetic particles and electron injection on transport of minority carriers and non-equilibrium carrier recombination in Ga₂O₃ is summarized in this review. In Ga₂O₃ semiconductor, if robust p-type material and bipolar structures become available, diffusion length of minority carriers will be of critical significance. Diffusion length of minority carriers dictates functionality of such electronic devices as diodes, transistors, and detectors. One of the problems in ultra-wide band gap materials technology, is the short carrier diffusion length, due to scattering on extended defects. Electron injection in n- and p-type Gallium Oxide results in a significant increase of the diffusion length, even after its deterioration due to exposure to alpha- and proton-irradiation. Furthermore, post electron injection diffusion length in irradiated material exceeds that in Ga₂O₃ prior to irradiation and injection. The root cause of the electron injection-induced effect is attributed to the increase of minority carrier lifetime in the material due to trapping of non-equilibrium electrons on native point defects. It is, therefore, concluded that the electron injection is capable of “healing” the adverse impact of radiation in Ga₂O₃ and can be used for control of minority carrier transport and, therefore, device performance.

With the popularization of natural gas and the requirements for environmental protection, the development and utilization of natural gas is particularly important. The status of natural gas in China's oil and gas exploration and development is constantly improving, and the country is paying more and more attention to the exploitation and utilization of natural gas. The Upper Paleozoic tight sandstone in the Ordos Basin is characterized by low porosity, low permeability and large area of concealed gas reservoirs. By injecting CO2 into the formation, the recovery of natural gas can be improved, and at the same time, the stable storage of CO2 can be achieved to achieve a win-win situation of CO2 emission reduction and utilization. Injecting greenhouse gas CO2 into gas reservoirs for storage and improving recovery has also become a hot research issue. In order to improve the recovery efficiency of tight sandstone gas reservoir, this paper takes the complex tight sandstone of Upper Paleozoic in Ordos Basin as the research object, through indoor physical simulation experiments, carried out the influence of displacement rate, fracture dip angle, core permeability, core dryness and wetness on CO2 gas displacement efficiency and storage efficiency, and analyzed the influence of different factors on CO2 gas displacement efficiency and storage efficiency to improve the recovery and storage efficiency. The research results show that under different conditions, when the CO2 injection pore volume is less than 1PV, the relationship between the CH4 recovery rate and the CO2 injection pore volume is linear, and the tilt angle is 45 °. When the CO2 injection pore volume exceeds 1PV, the CH4 recovery rate increases slightly with the increase of displacement speed, the recovery rate of CO2 displacement CH4 is between 87% - 97%, and the CO2 breakthrough time is 0.7PV-0.9PV. In low-permeability and low-speed displacement cores, the diffusion of CO2 molecules is more significant. The lower the displacement speed is, the earlier the breakthrough time of CO2 is, and the final recovery of CH4 slightly decreases. Gravity has a great impact on CO2 storage and enhanced recovery. The breakthrough of high injection and low recovery of CO2 is earlier, and the recovery of CH4 is about 3.3% lower than that of low injection and high recovery. The bound water makes the displacement phase CO2 partially dissolved in the formation water, and the CO2 breakthrough lags about 0.1PV. Ultimately, CH4 recovery factor and CO2 storage rate are higher than those of dry core displacement. The research results provide theoretical data support for CO2 injection to improve recovery and storage efficiency in complex tight sandstone gas reservoirs.

Evaluating new, promising organic molecules to make next-generation organic optoelectronic devices necessitates the evaluation of charge carrier transport performance through the semi-conducting medium. In this work, we utilize quantum chemical calculations (QCC) and kinetic Monte Carlo (KMC) simulations to predict the zero-field hole mobilities of ~100 morphologies of the benchmark polymer poly(3-hexylthiophene), with varying simulation volume, structural order, and chain-length polydispersity. Morphologies with monodisperse chains were generated previously using an optimized molecular dynamics force-field and represent a spectrum of nanostructured order. We discover that a combined consideration of backbone clustering and system-wide disorder arising from side-chain conformations are correlated with hole mobility. Furthermore, we show that strongly interconnected thiophene backbones are required for efficient charge transport. This definitively shows the role "tie-chains" play in enabling mobile charges in P3HT. By marrying QCC and KMC over multiple length- and time-scales, we demonstrate that it is now possible to routinely probe the relationship between molecular nanostructure and device performance.

In this study, a modular multi-step photometric microflow injection analysis (micro-FIA) system for the automatic determination of Cu(II) in a bioreactor has been developed. The system incorporates diverse 3D-printed modules, including a platform formed by a mixer module to mix Cu(II) with hydroxylamine which reduces Cu(II) to Cu(I) linked to a diluter module via a Tesla valve, a chelation mixer module, a disperser module, and a detector module provided by a LED light source at λ= 455 nm and a light dependence resistor (LDR) as a light intensity detector. The system measures the color intensity resulting from the chelation between Cu(I) and neocuproine. The micro-FIA system has demonstrated good capability for automatic and continuous Cu(II) determination, in a wide range of Cu concentrations from 34 to 2000 mg L-1. The device exhibits a good repeatability (coefficient of variation below 2% across the concentration range), good reproducibility, and has an accuracy of around 100% between 600 to 1900 mg·L-1. Real samples were analyzed using both the micro-FIA system and an atomic absorption spectroscopy method, revealing no statistically significant differences. Additionally, a Tesla valve located before the detector substituted a 3-way solenoid valve, eliminating the need for moving parts.

This study presents a novel approach to enhance Large Language Models (LLMs) like Alpaca by dynamically integrating real-time information. This method addresses the issue of content hallucination and data relevancy by automatically collecting and integrating current data from credible sources into model prompts. Experiments show a significant improvement in accuracy and a decrease in content hallucination, with a manageable increase in response time. The research underscores the potential of real-time data integration in making LLMs more accurate and contextually relevant, setting a foundation for future advancements in dynamic data processing in AI.

This work focuses on forced combustion with regards to the relationship between vent mixer models and several injection locations in unheated supersonic flow. A plasma jet torch was used to ignite the hydrogen–air mixture in a laboratory-scaled combustor duct. The flow field of the combustion was visualized with pressure and gas-sampling measurements. The vent mixers indicate good dispersion characteristics of the mixture for both parallel and normal 1 injections. However, forced combustion is dominantly governed by the injection rate toward the plasma jet (hot source) because the combustible region is restricted under the cold main flow. For this reason, the parallel injection, which provides the hydrogen–air mixture directly toward the plasma jet, shows good combustion performance. The normal 1 injection interacted with the vent mixers and shows slightly good combustion performance. Lastly, the normal 2 injection is little affected by the vent mixers and has poor combustion performance.

We have recently introduced the possibility of performing operando small-angle X-ray scattering measurements using a novel industrially relevant injection moulding system for plastics. We show that useful time-resolving measurements can be performed with a time-cycle of 1s and we highlight the possible steps to reduce this to 0.5s. We show how we can use the transmission measurements to provide a time-marker when plastic first enters the mould cavity in the region probed by the incident X-ray beam. We show the opportunities provided by this experimental stage mounted on the NCD-SWEET beamline at ALBA to probe the reproducibility of the injection moulding system on different scales. The design of the equipment allows the development of the structure and the morphology to be evaluated in different parts of mould cavity and we evaluate any differences in a rectangular mould cavity. We identify future prospects for this equipment in terms of novel mould heating and cooling systems and the opportunities for quantitatively evaluating radical approaches to injection moulding technology.

Minimum miscibility pressure (MMP) and oil swelling are two important factors of carbondioxide (CO₂) gas displacement mechanism occurred in the reservoir relate to application of CO₂ injection in the field to enhance oil recovery. In this paper determination of minimum miscibility pressure (MMP) between crude oil samples with carbondioxide gas conducted using two methods, i.e. correlation methods and laboratory experiment using slimtube. While, determination of swelling factor was conducted using PVT cell, where recombined fluid injected and conditionally at the reservoir temperature. The results of MMP using empirical equation (2807 Psig) and Holm & Josendal correlation (2750 Psig) is more approximate to the result of laboratory analysis (2805 Psig). The result of swelling test during injection CO₂ gas processes until 46.82% mole, shows that bubble point pressure is increasing gradually from 410 psig through 2200 psig, and swelling factor was also increase from 1.0 through 1.442. Based on the value of fracture pressure of Layer F in the KHL Field is 2200 Psig and MMP is 2805 Psig, hence the application of CO₂ gas injection in the field only could be conducted as immiscible flooding.

Safe sample transport is of great importance for infectious diseases diagnostics. Various treatments and buffers are used to inactivate pathogens in diagnostic samples. At the same time, adequate sample preservation, particularly of nucleic acids, is essential to allow an accurate laboratory diagnosis. For viruses with single-stranded RNA genomes of positive polarity, such as foot-and-mouth disease virus (FMDV), however, naked full-length viral RNA can itself be infectious. In order to assess the risk of infection from inactivated FMDV samples, two animal experiments were performed. In the first trial, six cattle were injected with FMDV RNA (isolate A22/IRQ/24/64) into the tongue epithelium. All animals developed clinical disease within two days and FMDV was reisolated from serum and saliva samples. In the second trial, another group of six cattle was exposed to FMDV RNA by instilling it on the tongue and spraying it into the nose. The animals were observed for 10 days after exposure. All animals remained clinically unremarkable and virus isolation as well as FMDV genome detection in serum and saliva were negative. No transfection reagent was used for any of the animal inoculations. In conclusion, cattle can be infected by injection with naked FMDV RNA, but not by non-invasive exposure to the RNA. Inactivated FMDV samples that contain full-length viral RNA carry only a negligible risk of infecting animals.

The present study evaluates the manufacturing parameters effects on the tensile properties of material composed by polylactic acid (PLA) with wood fibers known as Timberfill. The specimens were built through fused filament fabrication (FFF). The influence of four printing parameters (Layer height, Fill density, Printing velocity, and Orientation) are considered through a L27 Taguchi orthogonal array in order to reduce experimental runs. Tensile test is applied to obtain the response variable used as output results to perform the ANOVA calculations. Fill density is the most influential parameter on the tensile strength, followed by building orientation and layer height, whereas the printing velocity shows no significant influence. The optimal set of parameters and levels is found, being 75% fill density, 0○Z-axis orientation, 0.4 mm layer height, and 40 mm/s velocity as the best combination. Applying this combination showed 9.37 MPa in maximum tension. Lastly, five solid Timberfill specimens manufactured via injection molding technology were also tested and the results compared to the printed samples. The values of the elastic modulus, elastic limit, and maximum tension of the injected samples were almost twofold of those were obtained for the FFF samples, but the maximum elongation of injected specimens was fell sharply.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

This paper presents an improved SOC estimation method for lithium ion batteries in Electric Vehicles using Bayesian optimized feedforward network. This innovative bayesian optimized neural network method attempts to minimize a scalar objective function by extracting hyperpa-rameters (hidden neurons in both layers) using a surrogate model. Furthemore, the hyperparameters are built and data samples are trained and validated. The performance of the proposed deep learning neural network is evaluated. Two reasonable size data samples are ex-tracted from Panasonic 18650PF Li-ion Mendeley datasets that are used for training and valida-tion. RNN and LSTM neural network algorithms offer the common core property of retaining past information and/or hidden states for better SOC estimation. However, the feature of this pro-posed method is the inclusion of Bayesian optimization that chooses optimal double layer hidden neurons. Analysis of results shows that Bayesian optimized feedforward algorithm with average MAPE (0.20%) is the lowest and is the best selection compared with average MAPE for other five deep learning algorithms. In the last quarter of fuel gauge, where fuel anxiety is severe, feed-forward with Bayesian Optimization algorithm is still the best selection (with MAPE of 0.64%).

4-component relativistic atomic and molecular calculations are typically performed within the no-pair approximation where negative-energy solutions are discarded, hence the symmetry between electronic and positronic solutions is not considered. These states are however needed in QED calculations, where furthermore charge conjugation symmetry becomes an issue. In this work we shall discuss the realization of charge conjugation symmetry of the Dirac equation in a central field within the finite basis approximation. Three schemes for basis set construction are considered: restricted, inverse and dual kinetic balance. We find that charge conjugation symmetry can be realized within the restricted and inverse kinetic balance prescriptions, but only with a special form of basis functions that does not obey the right boundary conditions of the radial wavefunctions. The dual kinetic balance prescription is on the other hand compatible with charge conjugation symmetry without restricting the form of the radial basis functions. However, since charge conjugation relates solutions of opposite value of the quantum number κ, this requires the use of basis sets chosen according to total angular momentum j rather than orbital angular momentum ` . As a special case, we consider the free-particle Dirac equation, where the solutions of opposite sign of energy are related by charge conjugation symmetry. We note that there is additional symmetry in those solutions of the same value of κ come in pairs of opposite energy.

Below T_CO=157 K the quasi-one-dimensional charge-transfer salt (TMTTF)_2SbF_6 undergoes a pronounced phase transition to a charge-ordered ground state. We have explored the non-linear and photoconductive behavior as a function of applied voltage, laser pulse energy and temperature. Besides a decay of the photoconductive signal in a double exponential fashion in the millisecond range, we discover current oscillations in the kHz range induced by the application of short laser pulses. While the resonance frequencies do not depend on voltage or laser intensity and vary only slightly with temperature, the amplitude changes linearly with the laser intensity and voltage. The findings are discussed and compared to comparable phenomena in other low-dimensional electron systems.

In this review, we provide an overview of the most common majority and minority charge carrier traps in n-type 4H-SiC material. We focus on the results obtained by different applications of junction spectroscopy techniques. The basic principles behind the most common junction spectroscopy techniques are given. These techniques, namely, deep level transient spectroscopy (DLTS), Laplace DLTS (L-DLTS) and minority carrier transient spectroscopy (MCTS) have led to recent progress in identifying and better understanding of the charge carrier traps in n-type 4H-SiC material.

We examine here the discrepancy between the radiated power, calculated from the Poynting flux at infinity, and the power loss due to radiation reaction for an accelerated charge. It is emphasized that one needs to maintain a clear distinction between the electromagnetic power received by distant observers and the mechanical power loss undergone by the charge. In literature both quantities are treated as almost synonymous, the two in general could, however, be quite different. It is shown that in the case of a periodic motion, the two formulations do yield the power loss in a time averaged sense to be the same, even though, the instantaneous rates are quite different. It is demonstrated that the discordance between the two power formulas merely reflects the difference in the power going in self-fields of the charge between the retarded and present times. In particular, in the case of a uniformly accelerated charge, power going into the self-fields at the present time is equal to the power that was going into the self-fields at the retarded time plus the power going in acceleration fields, usually called radiation. From a comparison of the far fields with the instantaneous location of the uniformly accelerated charge, it is shown that all its fields, including the acceleration fields, remain around the charge and are not radiated away from it.

This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented by x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x = 3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

Abstract: This computational research study analyzes the increase of the specific charge capacity that comes with the reduction of the anisotropic volume expansion during lithium ion insertion within silicon nanowires. This research paper is a continuation from previous work that studied the expansion rate and volume increase. It has been determined that when the lithium ion concentration is decreased by regulating the amount of Li ion flux, the lithium ions to silicon atoms ratio, represented x, decreases within the amorphous lithiated silicon (a-LixSi) material. This results in a decrease in the volumetric strain of the lithiated silicon nanowire as well as a reduction in Maxwell stress that was calculated and Young’s elastic module that was measured experimentally using nanoindentation. The conclusion as will be seen is that as there is a decrease in lithium ion concentration there is a corresponding decrease in anisotropic volume and a resulting increase in specific charge capacity. In fact the amplification of the electromagnetic field due to the electron flux that created detrimental effects for a fully lithiated silicon nanowire at x=3.75 which resulted in over a 300% volume expansion becomes beneficial with the decrease in lithium ion flux as x approaches 0.75 which leads to a marginal volume increase of ~25 percent. This could lead to the use of crystalline silicon, c-Si, as an anode material that has been demonstrated in many previous research work to be ten times greater charge capacity than carbon base anode material for lithium ion batteries.

The use of biodiesel fuels in compression ignition engines leads to decrease CO, PM, HC and smoke opacity. However, NOx emissions increase importantly. Various methods to reduce NOx are used namely the EGR, the water injection method and the steam injection method. In this study, the steam injection method has been used instead of the other methods because of its benefits. This study examines the effects of steam injection on combustion products of diesel and biodiesel fuels by considering chemical equilibrium in order to determine the equilibrium combustion products involving 10 combustion products. A developed simulation code determing the equilibrium mole fractions and thermodynamic properties of combustion products is used for diesel and biodiesel fuels. It can be used for any fuel consisting of carbon, hydrogen or any oxygenated fuel. The results show that the mole fraction of CO2 and CO decrease with the steam injection ratios. NO mole fractions decrease with steam injection for lean mixtures but they increase slightly in the case of rich mixtures. The specific heat of combustion products increase with the steam injection ratios. Thus, the engine performance can be improved using the method. The model has been validated by comparing model results with the ones of NASA CEA software and GASEQ software using the methane as fuel. The relative errors of equilibrium mole fractions and thermodynamic properties of combustion products are less than 0.98 %.

Transcutaneous injection laryngoplasty is a well-known procedure for treating paralyzed vocal fold by injecting augmentation material into it. Hence, vocal fold localization plays a vital role in the preoperative planning as the fold location is required to determine the optimal injection route. In this communication, we propose a mirror environment based reinforcement learning (RL) algorithm for localizing the right and left vocal folds in preoperative neck CT. RL-based methods commonly showed noteworthy outcome in general anatomic landmark localization problem in the recent years. However, such methods suggest training individual agent for localizing each fold, though the right and left vocal folds are located in close proximity and have high feature-similarity. Utilizing the lateral symmetry between the right and left vocal folds, the proposed mirror environment allows for a single agent for localizing both the folds by treating the left fold as a flipped version of the right fold. Thus, localization of both folds can be trained using a single training session which utilizes the inter-fold correlation and avoids redundant feature learning. Experiment with 120 CT volumes showed improved localization performance and training efficiency of the proposed method compared with the standard RL method.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

In the present, the growth of digitization and worldwide communications make OCR systems of exotic languages a very important task. In this paper, we attempt to develop an OCR system for one of these exotic languages with a unique script, Amharic. Motivated by the recent success of the Attention mechanism in Neural Machine Translation (NMT), we extend the attention mechanism for Amharic text-image recognition. The proposed model consists of CNNs and attention embedded recurrent encoder-decoder networks that are integrated following the configuration of the seq2seq framework. The attention network parameters are trained in an end-to-end fashion and the context vector is injected, with the previously predicted output, at each time steps of decoding. Unlike the existing OCR model that minimizes the CTC objective function, the new model minimizes the categorical cross-entropy loss. The performance of the proposed attention-based model is evaluated against the test dataset from the ADOCR database which consists of both printed and synthetically generated Amharic text-line images and achieved promising results with a CER of 1.54% and 1.17% respectively.

Currently, for the serious air pollution and global warming effect caused by the substance released from the present vehicle, it is expected that the regulatory requirements for the emission will become more stringent. A new concept of the combustion technology that can reduce the NOx and PM related to combustion is urgently needed. To cope with such social demands, many developed countries are efforts to develop the environment friendly vehicle engine at the national lever in order to satisfy with strengthening emission control. As a main combustion technology among new combustion technology for the new generation engine, the homogenous charge compression engine (HCCI) is expanding its application range by employing multiple combustion mode, catalyst, direct fuel injection and partially premixed combustion. In this paper, a multi-injection method in order to apply the HCCI combustion method without mainly altering engine specifications and practicality by referring to the results of the HCCI engine was investigated. Applied with forced charging, exhaust gas recirculation (EGR) and compression ratio change, it was evaluated to the possibility of securing optimum fuel economy and emission reduction in the IMEP 0.8 MPa range.

Background: Regardless of the indisputable benefits of insulin therapy, initiating insulin for diagnosed children with diabetes might be intimidating for parents. This study assesses the experience, fears, barriers and adherence to insulin use among the parents of diagnosed children with diabetes. Methods: A cross-sectional online survey was utilized for data collection from 218 participants between February and March 2023 in Jordan. The survey consisted of six sections to evaluate and assess: sociodemographic for both children with diabetes and their parents, the experience of using the insulin, the diabetes fear of self-injecting questionnaire (D-FISQ), the barriers for insulin administration including both sociocultural and other insulin-related factors, and insulin adherence. Results: More than 80% of the participants perceived a number of sociocultural barriers to insulin administration such as the tendency for addiction, lower efficiency of insulin than oral medication, and preference for complementary medicine over insulin. More than two-thirds of the participants complained of insulin-related barriers such as infections and sudden death in addition to learning the correct injection method. The general fear level was low, 8.56±7.87 (out of 45); however, more fear of insulin injection and self-testing was significantly associated with both sociocultural and insulin-related barriers, especially at the younger age. Conclusion: The results of this study indicated that parents have several barriers to insulin administration, mainly related to insulin injection. Therefore, more awareness about insulin therapy can help adjust the cooperation of patients, acceptance of treatment, ending with improving the quality of life and well-being.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

We propose a new methodology for long-time biopotential recording based on MEMS multisensor integrated platform featuring a commercial electrostatic charge transfer sensor. That family of sensors was originally intended for presence tracking in automotive, so the existing setup has been engineered for the acquisition of electrocardiogram, electroencephalogram, electrooculogram and electromyography, designing a dedicated front-end and writing a proper firmware for the specific application. Systematic tests on controls and nocturnal acquisitions from patients in domestic environment will be discussed in detail. The excellent results candidate this technology to provide a low power, unexplored solution to biopotentials acquisition. The technology breakthrough is in that it enables adding this type of functionality to existing MEMS boards at near-zero additional power consumption. For these reasons, they open to additional possibilities for wearable sensing and strengthen the role of MEMS technology in medical wearable applications for long time synchronous acquisition of a wide range of signals.

Luminophores featuring thermally activated delayed fluorescence (TADF luminophores) are the workhorse of the third- and fourth-generation OLEDs. While these compounds had usually been used as dopants embedded in the host, non-doped TADF OLEDs have recently shown significant progress as well reaching the performance comparable to the host-dopant ones. For efficient operation of the non-doped OLEDs, charge transport in neat films and single crystals of TADF luminophores is important; however, this issue was nearly unexplored theoretically. In the current study, we calculated charge mobilities in four TADF single crystals, which have different molecular packing motifs. Specifically, in one of them both donor and acceptor moieties form uniform π-stacks, while in the others donors (acceptors) show alternating lateral shifts along the stacks; the difference in molecular packing results in the difference of transfer integral between the molecules. Reorganization energies differ as well up to four times for the studied crystals. As a result, charge mobilities vary from 0.001 to ~0.3 cm2/(V∙s), the largest being predicted for the crystal of the luminophore consisting of rigid donor and acceptor. We anticipate that the results obtained can be useful for the design of TADF luminophores for non-doped OLEDs, OLETs and other organic light-emitting devices.

As one of the critical state parameters of the battery management system, lithium battery state of charge (SOC) can provide an essential reference for battery safety management, charge/discharge control, and energy management of electric vehicles. To analyze the application of deep learning in electric vehicle power battery SOC estimation, this study reviewed the technical process, common public datasets, and the neural networks used, structural characteristics, advantages and disadvantages of lithium battery SOC estimation in deep learning method. First, the specific technical processes of the deep learning method for SOC estimation were analyzed, including data collection, data preprocessing, feature engineering, model training, and model evaluation. Secondly, the current commonly and publicly used lithium battery dataset was summarized. Then, the input variables, data sets, errors, and advantages and disadvantages of four types of deep learning methods, were concluded using the structure of neural network used for training as the classification criterion. Finally, the challenges and future development directions of lithium battery SOC estimation in deep learning method were explained.

The conformational dependence of the matrix element for spin-orbit coupling and of the electronic coupling for charge separation are determined for an electron donor-acceptor system containing a pyrene acceptor and a dimethylaniline donor. Different kinetic and energetic aspects that play a role in the spin-orbit charge transfer intersystem crossing (SOCT-ISC) mechanism are discussed. This includes parameters related to initial charge separation and the charge recombination pathways using the (Semi-Classical) Marcus Theory for electron transfer. The spin-orbit coupling, which plays a significant role in charge recombination to the triplet state can be probed by (TD-)DFT, using the latter as a tool to understand and predict the SOCT-ISC mechanism. The matrix elements for spin-orbit coupling for acetone and 4-thio-thymine are used for benchmarking. (Time Dependent-) Density Functional Theory (DFT and TD-DFT) calculations are applied using the quantum chemical program Amsterdam Density Functional (ADF).

The structure and phenomena arising from charge transfer in cold field emission modus in a single closed carbon nanotube under cold field emission conditions were studied. By studying microphotographs in various microscopes - AFM, SEM, TEM it was found inhomogeneities in the form of two types of superlattices. The conductivity of the emitter section of a nanodiode circuit with an emitter made of an individual closed carbon nanotube (CNT) and arrays of closed CNTs was studied. High values of cold field emission were observed, as well as nonlinearity and anomalies of the current-voltage characteristic (I-V characteristics), which manifested themselves in the form of peaks at low and high current values. Peaks in the CVC have distinct areas of negative differential conductivity. It is argued, that the anomalously high currents in the I–V characteristics of cold field emission of electrons from a nanoemitter made of closed CNTs can be associated with a sharp increase in the density of electron states at energies near the van Hove singularity.

Blast charge initiation procedures have a significant impact on both mining safety and production rates. In this study, the inventory benefit of an electric initiation system was investigated to assess its influence on both fragmentation and blast-induced damages. The Wipfrag software's was used to examine the size distribution and productivity of 12 small-scale blasts initiated by both non-electric and electric detonators. All blast rounds was initiated with plain type of electric and NONEL detonators. The average burden, spacing, stemming length, and charge weight were, respectively, 0.85 m, 1.10 m, 0.66m, and 1.1kg. The results showed that the mesh through which 80% of the blast fragments will pass for the electric blast is smaller than the mesh through which the material products from the NONEL blast will pass. The results also demonstrate that the generated blast-induced ground vibration (PPV) from all blast rounds for electric blast varies from 0.4–1.2 mm/s and 80–105dB, while that for non-electric blast ranges from 0.05–0.2mm/s and 72–95dB. As a result, the electric blast initiation technique was found to produce good fragmentation, with a higher percentage of optimum fragment sizes on spec than non-electrically initiated blasts.

The role of initial state (ISI) and final state (FSI) ion–ion interactions in heavy ion double charge exchange (DCE) reactions A(Z,N)→A(Z±2,N∓2) are studied in the context of double single charge exchange (DSCE) reactions given by sequential actions of the isovector nucleon–nucleon (NN) T–matrix. The second order DSCE reaction amplitude is investigated in momentum representation in a formulation, focused on the extraction of nuclear matrix elements under the conditions of strong initial state (ISI) and final state (FSI) interactions. In closure approximation and using the momentum representation, the reaction amplitude is finally separated into ISI/FSI distortion coefficients and reaction kernels and nuclear matrix elements. The ISI/FSI reaction kernels emerge as the result of the repeated scattering on the avoided volume, introduced by the imaginary parts of the ion–ion optical potential and acting as sinks for the quantal probability current. The closure approximation allows derive a set of induced effective two–body isotensor interactions, given by products of spin–scalar, spin–vector central and rank–2 spin–tensor interactions. The intermediate propagator plays a key role in establishing correlation between the DCE transitions in the projectile and target nucleus. The presented approach emphasizes the special features of DSCE reaction dynamics as proceeding like a system of two coupled isospin dipoles whose strengths are determined by the momentum-space form factors of the NN isovector interaction. The properties of the DSCE interaction form factors are investigated and the approach is applied to data.

The objective of this study was to investigate the liquefaction resistance of chemically improved sandy soils in a straightforward and accurate manner. Using only the existing experimental databases and artificial intelligence, the goal was to make predictions without conducting physical experiments. Emphasis was placed on the significance of data from 20 loading cycles of cyclic undrained triaxial tests to determine the liquefaction resistance and the contribution of each explanatory variable. Different combinations of explanatory variables were considered. Regarding the predictive model, it was observed that a case with the liquefaction resistance ratio as the dependent variable and other parameters as explanatory variables yielded favorable results. In terms of exploring combinations of explanatory variables, it was found advantageous to include all variables as doing so consistently resulted in a high coefficient of determination. The inclusion of the liquefaction resistance ratio in the training data was found to improve the predictive accuracy. In addition, the results obtained when using a linear model for the prediction suggested the potential to accurately predict the liquefaction resistance using historical data.

SQL injection attacks are one of the most common types of attacks on web applications. These attacks exploit vulnerabilities in the application’s database access mechanisms, allowing attackers to execute unauthorized SQL queries. In this study, we propose an architecture for detecting SQL injection attacks using a recurrent neural network (RNN) autoencoder. The proposed architecture was trained on a publicly available dataset of SQL injection attacks. Then compared with several other machine learning models, including ANN, CNN, Decision Tree, Naïve Bayes, SVM, Random Forest, and Logistic Regression. The experimental result showed that the proposed approach achieved an accuracy of 94% and an F1 score of 92%, which demonstrate its effectiveness in detecting QL injection attacks with high accuracy in comparison with other models covered in the study.

Tarsal tunnel syndrome is a focal compressive neuropathy of the posterior tibial nerve or one of its associated branches. Brief mention is made in the literature of the use of corticosteroid injections for this condition. The basic technique of hydrodissection is used for other nerve entrapments and includes identifying the region of nerve compression, and the injection of a fluid medium to dissect between structures or fascial planes. We introduce our treatment protocol using a methylprednisolone/sterile water/ropivacaine hydrochloride injectate mix and peripheral nerve stimulation to a perform hydrodissection technique for tarsal tunnel syndrome.

Current clinical treatment options for symptomatic, partial-thickness rotator cuff tear (sPTRCT) offer only limited potential for true tissue healing and improvement of clinical results. In animal models, injections of adult stem cells isolated from adipose tissue into tendon injuries evidenced histological regeneration of tendon tissue. However, it is unclear whether such beneficial effects could also be observed in a human tendon treated with fresh, uncultured, autologous, adipose derived regenerative cells (UA-ADRCs). A specific challenge in this regard is that UA-ADRCs cannot be labeled and, thus, not unequivocally identified in the host tissue. Therefore, histological regeneration of injured human tendons after injection of UA-ADRCs must be assessed using comprehensive, immunohistochemical and microscopic analysis of biopsies taken from the treated tendon a few weeks after injection of UA-ADRCs.

1) Background: Recently, illegal abuse of γ-hydroxybutyric acid (GHB) has increased in drug-facilitated crimes, but determination of GHB exposure and intoxication is difficult due to rapid metabolism of GHB. Its biochemical mechanism has not been completely investigated. And metabolomic study by polyamine profile and pattern analyses was not performed in rat urinefollowing intraperitoneal injection with GHB. 2) Methods: Polyamine profiling analysis by gas chromatography-mass spectrometry combined with star pattern recognition analysis was performed in this study. Multivariate statistical analysis was used to evaluate discrimination between control and GHB administration groups. 3) Results: Six polyamines were determined in control, single and multiple GHB administration groups. Star pattern showed distorted hexagonal shapes with characteristic and readily distinguishable patterns for each group. N¹-Acetylspermine (p < 0.001), putrescine (p <0.006), N¹-acetylspermidine (p <0.009), and spermine (p < 0.027) were significantly increased in single administration group but were significantly lower in the multiple administration group than in the control group. N¹-Acetylspermine was the main polyamine for discrimination between control, single and multiple administration groups. Spermine showed similar levels in single and multiple administration groups. 4) Conclusions: The polyamine metabolic pattern was monitored in GHB administration groups. N¹-Acetylspermine and spermine were evaluated as potential biomarkers of GHB exposure and addiction.

This study evaluates the viability of n-octanol as an alternative fuel in a direct-injection diesel engine, aiming to enhance sustainability and efficiency. Experiments employed varying blends of n-octanol (10%, 30%, and 50% by volume) with pure diesel, analyzing impacts on engine performance and emissions. The methodology involved testing each blend in a single-cylinder engine, measuring engine performance parameters such as brake torque and brake power under full load conditions across an engine speed range from 1400 to 2500 rpm. Comparative assessments of performance and emission characteristics at a constant engine speed of 1700 rpm were also conducted with varying loads. Results indicated that while n-octanol blends consistently improved brake thermal efficiency, they also increased brake specific fuel consumption due to the lower energy content of n-octanol. Consequently, while all n-octanol blends reduced nitrogen oxides (NOx) emissions compared to pure diesel, they also significantly decreased carbon monoxide, hydrocarbons, and smoke opacity, presenting a comprehensive reduction in harmful emissions. However, the benefits came with nuanced trade-offs: notably, higher concentrations of n-octanol (especially the 50% blend) led to a relative increase in NOx emissions as the octanol ratio increased. The study concludes that n-octanol significantly improves engine efficiency and reduces diesel dependence, but optimizing the blend ratio is crucial to balance performance improvements with comprehensive emission reductions.

Towards smart batteries for electric vehicles (EVs) smart algorithms to control battery packs, mainly reconfigurable batteries, have to be developed. This work proposes a reinforcement learning (RL) algorithm to balance the State of Charge (SoC) of reconfigurable batteries based on the topologies half-bridge and battery modular multilevel management (BM3). As RL algorithm, Amortized Q-learning (AQL) is implemented, which allows enourmous numbers of possible configurations of the reconfigurable battery to be controlled, as well as the combination of classical controlling approach and machine learning methods. This enables safety mechanisms in control. As a neural network of the AQL a Feedforward Neuronal Network (FNN) is implemented consisting of three hidden layers. The experimental evaluation using a 12-cell hybrid cascaded multilevel converter illustrates the applicability of the method to balance the SoC and maintain the balanced state during discharge. The evaluation shows a 20.3% slower balancing compared to the classical. Nevertheless, AQL shows great potential to be applied for multiobjective optimizations as an applicable RL algorithm for control in power electronics.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

We review the basics of nuclear binding energy scheme assumed to be associated with the existence of a new strong elementary charge associated with square root of reciprocal of the strong coupling constant.

Structure based biological and chemical properties of 4-(carboxyamino)-benzoic acid has been studied by quantum chemical methods. The revamped geometric structure and its quantum chemical parameters were obtained by DFT-B3LYP/6-311G method. Normal mode analysis is performed to assign the fundamental vibrational frequencies as per the potential energy distribution (PED) by using the VEDA program. Simulation of IR and Raman spectral patterns are observed by refinement of scale factors. TD-DFT approach is used to explore the excited states of molecule and prediction of electronic absorption spectra. NMR chemical shifts of the molecule are determined by the gauge independent atomic orbital method. The molecular docking is performed to recognize the binding energy of the ligand with the dynamic site of protein. In our docking analysis, the protein 5DT6 shows the best results than other three proteins which could be used for further analysis. Further inter and intra molecular interactions, electrophilic, nucleophilic and chemical reactivity sites are found by molecular electrostatic potential, HOMO-LUMO and Global chemical reactivity descriptors. Thermodynamic property of the title compound is also reported. The determined quantum chemical parameters show high reactivity and the dipole moment was sufficiently high enough to induce nonlinear characteristics which are required for applications in optoelectronic devices.

The study of interactions between polyelectrolytes (PE) and surfactants is of great interest for both fundamental and applied research. These mixtures can represent, for example, models of self-assembly and molecular organization in biological systems, but they are also relevant in industrial applications. Amphiphilic block polyelectrolytes represent an interesting class of PE, but their interactions with surfactants have not been extensively explored so far, most studies being restricted to non-associating PE. In this work, interactions between an anionic amphiphilic triblock polyelectrolyte and different types of surfactants bearing respectively negative, positive and no charge, are investigated via surface tension and solution rheology measurements for the first time. It is evidenced that the surfactants have different effects on viscosity and surface tension, depending on their charge type. Micellization of the surfactant is affected by the presence of the polymer in all cases; shear viscosity of polymer solutions decreases in presence of same charge or nonionic surfactants, while the opposite charge surfactant cause precipitation. This study highlights the importance of the charge type, and the role of the associating hydrophobic block in the PE structure, on the solution behavior of the mixtures. Moreover, a possible interaction model is proposed, based on the obtained data.

In this paper, a low-power Injection-Locked Clock and Data Recovery (ILCDR) using 28nm FDSOI technology is presented. The back-gate auto-biasing of UTBB-FDSOI transistors allows us to create a QRO (Quadrature Ring Oscillator) reducing both size and power consumption. By injecting a digital signal into this circuit, we realize an Injection-Locked Oscillator (ILO) with low jitter. Thanks to the good performance of this oscillator, we propose a low power ILCDR with fast locking time and low jitter for burst-mode applications. The main novelty consists in the implementation of a complementary QRO based on back-gate control using FDSOI technology to realize a simple and efficient ILCDR circuit. With a Pseudo-Random Binary Sequence (PRBS7) at 868Mbps, the recovered clock jitter is 26.7ps (2.3%UIp-p) and the recovered data jitter is 11.9ps (1%UIp-p). With a 0.6V power supply, the power consumption is 318μW. The estimated Chip area is around 6600μm².

Recently, in a previous study, we have experimentally shown the existence of an optimal injected steam mass flow rate, per unit length, ϕopt, which produces the maximal recovery of con- densate in a preformed steam chamber with an elliptical cross section of horizontal semi-major axis. Mutatis mutandis, in this work we present experimental studies in preformed steam chambers, one elliptical and the other circular. In both cases, we also have found the existence of unique optimal values. These configurations try to recreate the steam condensation, at a given time lapse, as it would occur during the growth stage of the steam-assisted gravity drainage (SAGD) process, a method used in the recovery of heavy and extra-heavy oil from homogeneous reservoirs. Finding the optimal mass flow rates in actual recovery process could become useful in the design of optimized SAGD processes.

In GDI engine applications, high-pressure (H.P.) injectors typically require to be designed to be capable of rapid response for GDI engines in order to be driven in the rapid response with respect to magnetic actuators, allowing for example more precise air-fuel ratio control in the GDI engines. The H.P. fuel injector is a highly dynamic component requiring careful voltage and pressure input modulation to achieve the required fuel injection quantities of GDI engines. The accurate fuel injection curves are a key influence for this technology, therefore will require the estimation of the fuel flow rate to be realized. In this paper, a PIC microchip for programming injector drive circuits is implemented to improve the performance of a H.P. fuel injector and tested to verify its feasibility. In the proposed injector drive circuit, powers MOSFETs directly control the charging/discharging current by a dsPIC30F4011 microchip. Design and analysis of the proposed injector drive circuit are presented. Next, effects of total pulse width, injector supply voltage, fuel system pressure and PWM operation on fuel injection quantities of a H.P. fuel injector are measured. Also, the measured data of the H.P. fuel injector fed by the injector driving circuit are defined as the fuel injection curves. Finally experimental results are provided for verification of the proposed injector drive circuit.

Whenever vegetated areas are monitored over time, phenological changes in land cover should be decoupled from changes in acquisition conditions, like atmospheric components, sun and satellite heights, and imaging instrument. This especially holds when the multispectral (MS) bands are sharpened for spatial resolution enhancement by means of a panchromatic (Pan) image of higher resolution, a process referred to as pansharpening. In this paper, we provide evidence that pansharpening of visible/near-infrared (VNIR) bands takes advantage from a correction of the path radiance term introduced by the atmosphere, during the fusion process. This holds whenever the fusion mechanism emulates the radiative transfer model ruling the acquisition of the Earth’s surface from space, that is, for methods exploiting a multiplicative, or contrast-based, injection model of spatial details extracted from the panchromatic (Pan) image into the interpolated multispectral (MS) bands. The path radiance should be estimated and subtracted from each band before the product by Pan is accomplished. Both empirical and model-based estimation techniques of MS path radiances are compared within the framework of optimized algorithms. Simulations carried out on two GeoEye-1 observations of the same agricultural landscape at different dates highlight that the de-hazing of MS before fusion is beneficial for an accurate detection of seasonal changes in the scene, as measured by the normalized differential vegetation index (NDVI).

Objective: This systematic review and meta-analysis compared the patient-reported outcomes of intra-articular facet joint injections of normal saline and selected active substances to identify a more effective agent for treating subacute and chronic low back pain (LBP). Methods: The PubMed, Embase, Scopus, Web of Science, and CENTRAL databases were searched for randomized controlled trials and observational studies published in English. A research quality assessment was performed using ROB2 and ROBINS-I. A meta-analysis was conducted using a random-effects model, and the mean differences (MD) with 95% confidence intervals (CI) in efficacy outcomes, including pain, numbness, disability, and quality of life, were assessed. Results: Of the 2,467 potential studies, three were included (247 patients). The active substances and normal saline had similar therapeutic effects on pain within 1 h, after 1-1.5 months, and after 3-6 months, with MD and 95% CI of 2.43 and -11.61 to 16.50, -0.63 and -7.97 to 6.72, and 1.90 and -16.03 to 19.83, respectively, as well as the quality of life after 1 and 6 months. Conclusion: The short- and long-term clinical effects of intra-articular facet joint injections of normal saline are comparable to those of other active substances in patients with LBP.

Photosystem I (PSI) serves as a model system for studying fundamental processes such as electron transfer (ET) and energy conversion, which are not only central to photosynthesis but also have broader implications for bioenergy production and biomimetic device design. In this study, we employed electron paramagnetic resonance (EPR) spectroscopy to investigate key light-induced charge separation steps in PSI isolated from several green algal and cyanobacterial species. Following photoexcitation, rapid, sequential ET occurs through either of two symmetric branches of donor/acceptor cofactors embedded within the protein core, termed the A and B branch. Using high-frequency (130 GHz) time-resolved EPR (TR-EPR) and deuteration techniques to enhance spectral resolution, we observed that at low temperatures prokaryotic PSI exhibits reversible ET in the A branch and irreversible ET in the B branch at low temperatures, while PSI from eukaryotic counterparts displays either reversible ET in both branches or exclusively in the B branch. Furthermore, we observed a notable correlation between low-temperature charge separation to the terminal [4Fe-4S] clusters of PSI, termed FA and FB, as reflected in the measured FA/FB ratio. These findings enhance our understanding of the mechanistic diversity of PSI's ET across different species and underscore the importance of experimental design in resolving these differences. Though further research is necessary to elucidate the underlying mechanisms and the evolutionary significance of these variations in PSI charge separation, this study sets the stage for future investigations into the complex interplay between protein structure, ET pathways, and the environmental adaptations of photosynthetic organisms.

The theory of heavy ion double charge exchange (DCE) reactions proceeding by effective rank–2 isotensor interactions is presented. Virtual pion–nucleon charge exchange interactions are investigated as the source for induced isotensor interactions, giving rise to the Majorana DCE (MDCE) reaction mechanism. MDCE is of a generic character, proceeding through pairs of complementary (π±,π∓) reactions in the projectile and target nucleus. The dynamics of the elementary processes is discussed where the excitation of pion–nucleon resonances are of central importance. Investigations of initial and final state ion–ion interactions show that these effects are acting as vertex renormalizations. In closure approximation, well justified by the finite pion mass, the second order transition matrix elements reduce to pion potentials and effective two–body isotensor DCE interactions, giving rise also to two–body correlations in either of the participating nuclei. Connections to neutrinoless Majorana double beta decay (MDBD) are elucidated at various levels of dynamics, from the underlying fundamental electro–weak and QCD scales to the physical scales of nuclear MDBD and MDCE physics. It is pointed out that heavy ion MDCE reactions may also proceed by competing electro–weak charge exchange processes, leading to lepton MDCE by electrons, positrons, and neutrinos.

By introducing a suitable renormalization process the charge carrier and phonon dynamics of a double-stranded helical DNA molecule is expressed in terms of an effective Hamitonian describing a linear chain, where the renormalized transfer integrals explicitly depend on the relative orientations of the Watson-Crick base pairs, and the renormalized on-site energies are related to the electronic parameters of consecutive base pairs along the helix axis, as well as to the low-frequency phonons dispersion relation. The existence of synchronized collective oscillations enhancing the π-π orbital overlapping among different base pairs is disclosed from the study of the obtained analytical dynamical equations. The role of these phonon-correlated, long-range oscillation effects on the charge transfer properties of double standed DNA homopolymers is discussed in terms of the resulting band structure.

Chemical versatility of organic semiconductors provides nearly unlimited opportunities for tuning their electronic properties. However, despite decades of research, relationship between molecular structure, molecular packing and charge mobility in these materials remains poorly understood. This reduces the search for high-mobility organic semiconductors to the inefficient trial-and-error approach. For clarifying the abovementioned relationship, investigations of the effect of small changes in the chemical structure on OSs properties are particularly important. In this study, we address computationally the impact of substitution of C-H atom pairs by nitrogen atoms (N-substitution) on molecular properties, molecular packing and charge mobility of crystalline oligoacenes. Besides of decreasing frontier molecular orbital levels, N-substitution dramatically alters molecular electrostatic potential yielding pronounced electron-rich and electron-deficient areas. These changes in the molecular electrostatic potential strengthen face-to-face and edge-to-edge interactions in the corresponding crystals and result in the crossover from the herringbone packing motif to π-stacking. When the electron-rich and electron-deficient areas are large, sharply defined and, probably, have certain symmetry, charge mobility increases up to 3-4 cm2V-1s-1. The results obtained highlight the potential of azaacenes for application in organic electronic devices and are expected to facilitate rational design of organic semiconductors for steady improvement of organic electronics.