Hydrogen is considered as an ideal substitute to the traditional fossil fuels because of its widespread sources, high calorific value of combustion, and zero carbon emissions. The electrocatalytic water-splitting to produce hydrogen is also deemed to be the best approach, however, it is a challenge to make high-efficient and low-cost electrocatalysts. Single-atom catalysts (SACs) are considered the most promising candidate to replace the traditional noble-metal catalysts. Compared with SACs, the dual-atom catalysts (DACs) are of greater attraction including higher metal loading, more versatile active sites, and excellent catalytic activity. In the review, several general synthetic strategies and structural characterization methods of DACs are introduced, and the mechanisms of hydrogen evolution reaction (HER) and oxygen evolution reactions (OER) are discussed. The authors hope that the review has given some insights and inspiration to the researchers about DACs in electrocatalytic water-splitting.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Based on screening in computational biology and biological in vitro assays, five natural products isolated from extracts of the herbal medicine toad skin, such as cinobufagin (CBFi), bufalin (BFi), arenobufagin (ABFi), telocinobufagin (TBFi), bufotalin (BFTi), were subjected to molecular docking calculations with the use of SARS-CoV-2 main protease (PDB 6LU7 and 7BTF) and top-scoring ligand-receptor complexes were obtained. The results showed that the binding energy of ABFi to the 3CL protein was -17.044kcal/mol, which was higher than CBFi and TBFi. However, the binding energy of ABFi to the RdRp protease was -23.250 kcal/mol, which was much lower than that of CBFi and TBFi, EVEN lower than that of ABFi to the 3CL protein. ABFi also has polar interactions with amino acids such as Glu811, Ser814, Ser681 and Thr680 of RdRp enzyme. The results revealed that ABFi had a moderate inhibitory effect on the cell proliferation of SARS-CoV-2 in vitro, with an inhibition rate of 61.12%, even weaker than Remdesivir. This new discovery provides us with new ideas for in-depth studies on the development of natural products with this class of structural generalizations as inhibitors of SARS-CoV-2, and provides an experimental basis for the next step of mechanistic studies.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

Coarse-grained molecular dynamics simulations are employed to investigate the spatiotemporal evolution of vesicles (polymersomes) by the self-assembly of randomly distributed amphiphilic BAB triblock copolymers with hydrophilic A and hydrophobic B blocks in an aqueous solution. The vesiculation pathway consists of several intermediate structures, such as an interconnected network of copolymer aggregates, a cage of cylindrical micelles and a lamellar cage. The cage-to-vesicle transition occurs at a constant aggregation number and practically eliminates the hydrophobic interfacial area between the B block and solvent. Molecular reorganization under-lying the sequence of morphology transitions from a cage-like aggregate to a vesicle is nearly isentropic. The end-to-end distances of isolated copolymer chains in solution and those within a vesicular assembly follow log normal probability distributions. This is attributed to the pre-ponderance of folded chain configurations in which the two hydrophobic end groups of a given chain stay close to each other. However, the probability distribution of end-to-end distances is broader for chains within the vesicle as compared to that of a single chain. This is due to the swelling of the folded configurations within the hydrophobic bilayer. Increasing the hydropho-bicity of the B block reduces the vesiculation time without qualitatively altering the self-assembly pathway.

Transcriptional regulations have been widely studied as one of the main bridges between biology and other basic sciences as well as medicine. The traffic across it has been mostly unidirectional: chemistry and physics provided a lot of tools for biology, although the supply is now saturating. The traffic in opposite direction, the supply of subjects to develop chemistry and physics, has been only a little. However, if there are any, the supply will be at least from transcription, because the notion of chemical reaction is the strongest. This topic is aimed to increase the opposite traffic by introducing the forefront of physicochemical studies of transcription.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

A four-step synthesis of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e. acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee.

The carbonyl iron particles were dispersed in a polychloroprene rubber (CR) matrix under an external magnetic field for practical application as microwave absorption composites film. The film prepared under external magnetic field with a thickness of only 0.54 mm showed least reflection loss of -15.98 dB and the reflection loss value less than -10.0 dB over the frequency range of 11.4~14.8 GHz. In comparison with the microwave absorption properties of calculation by transmission line theory based on the tested relative complex permittivity and permeability and film prepared by general route without external magnetic field, the film made with external magnetic field exhibited more excellent microwave absorption properties, strongly depending on the increment of anisotropy and rearrangement of magnetic particles. The results indicated the composite film made under external magnetic field have excellent microwave absorption properties, which suggest that the composites thin film could be used as a thinner and lighter microwave absorber.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Small interfering RNA (siRNA) holds significant therapeutic potential by silencing target genes through RNA interference. Current clinical applications of siRNA have been primarily limited to liver diseases, while achievements in delivery methods are expanding its applications to various organs, including the lungs. Cholesterol-conjugated siRNA emerges as a promising delivery approach due to its low toxicity and high efficiency. This study focuses on developing a cholesterol-conjugated anti-Il6 siRNA and the evaluation of its potency for the potential treatment of inflammatory diseases using the example of acute lung injury (ALI). The biological activities of different Il6-targeted siRNAs containing chemical modifications were evaluated in J774 cells in vitro. The lead cholesterol-conjugated anti-Il6 siRNA after intranasal instillation demonstrated dose-dependent therapeutic effects in a mouse model of ALI induced by lipopolysaccharide (LPS). The treatment significantly reduced Il6 mRNA levels, inflammatory cell infiltration, and the severity of lung inflammation. IL6 silencing by cholesterol-conjugated siRNA proves to be a promising strategy for treating inflammatory diseases, with potential applications beyond the lungs.

The global usage of veterinary antibiotics is significant. These antibiotics can be released into the aquatic environment and exert toxic effects on non-target organisms. To explore the physiological effects of tetracycline antibiotics on aquatic life, the growth characteristics of and toxin release from the cyanobacterium Microcystis aeruginosa (M. aeruginosa) were studied. Results showed that the toxicity order of the three target antibiotics was TC (tetracycline) > CTC (chlortetracycline hydrochloride) > OTC (oxytetracycline) in terms of inhibition occurrence time and the EC₁₀ and EC₂₅ values. Further, the target antibiotics regulated the production of MC-LR (microcystin-LR) to different degrees. CTC destroyed the M. aeruginosa cells and resulted in a decreased MC-LR release but stimulated the ability to synthesise MC-LR. OTC had a relatively weaker toxicity compared with CTC, while TC was the most toxic among the three antibiotics. Therefore, TC is friendly to the aquatic environment because it simultaneously reduced the intracellular and extracellular MC-LR content. These results aid our understanding of the effects of tetracycline antibiotics on Microcystis aeruginosa, which is important for environmental evaluation and protection. These results are also helpful for guiding the application of veterinary antibiotics in agricultural settings.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

The steady-state multiplicity of the porous, non-isothermal, catalyst pellet when two parallel and consecutive chemical reactions take place was analysed in this work. The geometry selected for the catalyst pellet is finite hollow cylinder. A numerical multigrid continuation technique with the preconditioned conjugate gradient squared as coarse grid solver was used. The continuation parameter is the dimensionless adiabatic heat rise (Prater number) for the first chemical reaction. The effect of the other governing parameters was analysed and the results are compared to those provided by the single chemical reaction.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

Background: Metabolic flux analysis (MFA) is an indispensable tool in metabolic engineering. The simplest variant of MFA relies on an overdetermined stoichiometric model of the cell’s metabolism under the pseudo-steady state assumption, to evaluate the intracellular flux distribution. Despite its long history, the issue of model error in the overdetermined MFA, particularly misspecifications of the stoichiometric matrix, has not received much attention. Method: We evaluated the performance of statistical tests from linear least square regressions, namely Ramsey RESET test, F-test and Lagrange multiplier test, in detecting model misspecifications in the overdetermined MFA, particularly missing reactions. We further proposed an iterative procedure using the F-test to correct such an issue. Result: Using Chinese hamster ovary and random metabolic networks, we demonstrated that: (1) a statistically significant regression does not guarantee high accuracy of the flux estimates, (2) the removal of a reaction with a low flux magnitude can cause disproportionately large biases in the flux estimates, (3) the F-test could efficiently detect missing reactions, and (4) the proposed iterative procedure could robustly resolve the omission of reactions. Conclusion: Our work demonstrated that statistical analysis and tests could be used to systematically assess, detect and resolve model misspecifications in the overdetermined MFA.

Advanced lithography requires highly sensitive photoresists to improve lithographic efficiency, and it is critical yet challenging to develop high-sensitivity photoresists and imaging strategies. Here, we report a novel strategy for ultra-high sensitivity using hexafluoroisopropanol (HFIP)-containing fluoropolymer photoresists. The incorporation of HFIP, with its strong electrophilic property and electron-withdrawing effect of the fluorine atoms, significantly increases the acidity of the photoresist after exposure, enabling imaging without conventional photoacid generators (PAGs). The HFIP-containing photoresist has been evaluated by electron beam lithography to achieve a trench of ~40 nm at an extremely low dose of 3 μC/cm2, which shows sensitivity enhancement by ~10 times to the commercial PAGs involved system, revealing its high-sensitivity and high-resolution features. Our results demonstrate a new type of PAGs and a novel approach to higher-performance imaging beyond conventional photoresist performance tuning.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

Previously, we described a 19-base pair double-stranded RNA with 3'-trinucleotide overhangs, acting as immunostimulatory RNA (isRNA). This molecule demonstrated notable antiproliferative effects on cancer cells, inhibited tumor growth, and elicited immunostimulatory and antiviral responses by inducing cytokine and interferon production. Within this study, we compared the efficiency of lung fibrosis development, initiated in mice by BLM or LPS using different schemes of induction. Then we compared the effect of isRNA used in a preventive or therapeutic regimen on the development of fibrosis in selected BLM- and LPS-induced mouse models and showed that isRNA can be used in pathological conditions accompanied by the development of inflammation and the risk of fibrosis formation, without adverse side effects. Prophylactic regimen of isRNA application is beneficial for prevention of the development of pulmonary fibrosis.

Homogeneous and heterogeneous chemical reactions in partially ionized magneto-nano-liquid are investigated theoretically using finite element method (FEM). The effects of ions and electrons collisions on the transport of heat and mass are analyzed for both the cases of heterogeneous and homogeneous chemical reactions. The simultaneous effects of dispersion of nanosized particles in partially ionized nano-liquid in the presence of magnetic field are also investigated. Through numerical experiments, it is noted that the temperature of partially ionized nano-liquid increases when electrons collision rate and ion collisions are increased. The transport rate of reacting species decreases when heterogeneous and homogeneous chemical reactions strengths are increased. It is also observed that the effect of electron collisions on the flow in y-direction is the same to that of ion collisions on the flow in y-direction. Homogeneous and heterogeneous chemical reactions have similar effects on concentration of chemically reacting species in qualitative sense. However, in quantitative sense, homogeneous chemical reaction has more significant effect on the concentration reacting species as compared to heterogeneous chemical reaction.

Bioconvective flows have attracted attention in recent years due to actual and potential applications. In this paper, we consider a steady and laminar convective MHD flow of a nanofluid with heat, mass and microorganism transfer with a heat source/sink present. In addition, we assume there exists a first order chemical reaction. The governing partial differential equations (PDEs) are reduced to ordinary differential equations (ODEs) using the scaling group transformation and the associated boundary value problem is then solved. The influences of selected governing parameters on the dimensionless velocity, temperature, nanoparticle concentration, density of motile microorganisms, skin friction, heat transfer, mass transfer, and motile microorganism density rates are computed and discussed

A sustainable green one pot procedure for the synthesis of dihydropyrimidinones (DHPMs) derivatives by a three-component reaction of β-ketoester derivatives, aldehyde and urea or thiourea over the alkali-treated H-ZSM-5 zeolite under ball-milling has been developed. The product was isolated by simple washing of the crude reaction residue with ethyl acetate followed by evaporation of solvent. The hierachical zeolite catalyst (MFI27_6) showed high yield (86–96%) of dihydropyrimidinones (DHPMs), in very short time (10-30 min). The catalyst is recycled for subsequent reactions in four runs without appreciable loss of activity and high yields of products provide efficient protocol for Biginelli reactions.

The one-dimensional MoS₂/carbon nanofibers (1D MoS₂/CNFs) are synthesized by electrospinning using exfoliated MoS₂ nanosheets and polyacrylonitrile as raw materials. The exfoliated MoS₂ nanosheets with size of about 150 nm are encapsulated in carbon nanofibers, and the free-standing MoS₂/CNFs can be easily cut into flexible tablet and directly used as binder-free anode for lithium storage. The resultant 1D MoS₂/CNFs exhibit a very high reversible capacity of 700 mAh g^-1 at 100 mA g^-1 after 50 cycles, high rate capacity (450 mAh g^-1 at 1000 mA g^-1 after 200 cycles) and good cycle stability.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Optical materials with a tunable localized surface plasmon resonance (LSPR) are of a great interest for applications in photonics and optoelectronics. In the present study we explored the potential of generating the LSPR band with an ultra-broad range of over 1000 nm in gold nanoparticles (NPs) precipitated through the thermal treatment in ZnO-Al2O3-SiO2 glass. Using the optical absorption spectroscopy, we demonstrated that the LSPR band's position and shape can be finely controlled by varying the thermal treatment route. Comprehensive methods including Raman spectroscopy, X-ray diffraction and high-resolution transmission electron microscopy were used to study the glass structure, while computational approaches were used for the theoretical description of the absorption spectra. Obtained results allowed us to suggest a scenario responsible for such abnormal LSPR band broadening which includes possible interparticle plasmonic coupling effect taking place during the liquid-liquid phase separation of the heat-treated glass. The formation of gold NPs with an ultra-broad LSPR band in glasses holds promise for sensitizing rare earth ion luminescence for new photonics devices.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

Environmental estrogen pollution and estrogen effects on the female reproduction system are well-recognized scientifically. Among the estrogens, 17 β-estradiol is a priority in environmental estrogen pollution, and it is also a major contributor to estrogen which regulates the female reproduction system. 17 β-estradiol is carcinogen and has a tumor promotion effect relating to breast cancer, lung cancer and others. It also affects the psychological well-being such as depression, fatigue and others. Thus, a simple method of detection of 17 β-estradiol will be important for both environmental estrogen pollution and women’s health care. This study demonstrates a simple-use, cost effective 17 β-estradiol biosensor system which can be used for both environment and women’s health care applications. The bio-recognition mechanism is based on the influence of the redox couple, K₃Fe (CN) ₆/K₄Fe (CN) ₆ by the interaction between 17 β-estradiol antigen and its α-receptor (ER- α; α-estrogen antibody). The transduction mechanism is an electrochemical analytical technique, differential pulse voltammetry (DPV). The levels of 17 β-estradiol antigen studied was between 2.25 pg/mL to 2,250 pg/mL, Phosphate buffered saline (PBS), tap water from the Cleveland regional water district, and simulate urine were used as the test media covering the potential application areas for 17 β-estradiol detection. An interference study by testosterone which has a similar chemical structure and molecular weight as those of 17 β-estradiol was carried out, and this 17 β-estradiol biosensor showed excellent specificity without any interference by similar chemicals.

In review, the operating principles of the most common bio sensing devices, detection methods and the identification sensitivity of analyzed molecules were shown. The central focus was done on hybridization analysis of nucleic acids (NA), which are considered to be one of the most important analytes in terms of diagnostic point of view. Constructions enabling to transfer the fact of formation of nucleotide probe/target complex in to detectable signal by optical, electrochemical or micromechanical (piezoelectric) sensors were presented in this review.

The physical roots, interpretation, controversies and precise meaning of the Landauer Principle are surveyed. Landauer's principle is a physical principle pertaining to the lower theoretical limit of energy consumption of computation. It states that an irreversible change in information stored in a computer, such as merging two computational paths, dissipates a minimum amount of heat kBTln2 per a bit of information to its surrounding. The Landauer Principle is discussed in the context of fundamental physical limiting principles, such as the Abbe diffraction limit, the Margolus-Levitin limit and the Bekenstein limit. Synthesis of the Landauer bound with the Abbe, Margolus-Levitin limit and Bekenstein limits yields the minimal time of computation, which scales as τmin~hkBT. Decrease in a temperature of a thermal bath will decrease the energy consumption of a single computation, but, in parallel, it will slow the computation. The Landauer principle bridges between John Archibald Wheeler “it from bit” paradigm and thermodynamics. Experimental verifications of the Landauer Principle are surveyed. Interrelation between thermodynamic and logical irreversibility is addressed. Generalization of the Landauer principle to the quantum and non-equilibrium systems is addressed. Landauer Principle represents the powerful heuristic principle bridging the physics, information theory and computer engineering.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

Clausius’ virial theorem set a basis for relating kinetic energy in a body of independent material particles to its potential energy, pointing to their complementary role with respect to the second law of maximum entropy. In action mechanics, expressing the entropy of ideal gases as a capacity factor for sensible heat or enthalpy plus the configurational work to sustain the relative translational, rotational and vibrational action yields algorithms for estimating chemical reaction rates and positions of equilibrium. All properties of state including entropy, work potential as Helmholtz and Gibbs energies and activated transition state reaction rates can be estimated, using easily accessible molecular properties, such as atomic weights, bond lengths, moments of inertia and vibrational frequencies. Understanding how Clausius’ virial theorem balances the internal kinetic energy with field potential energy justifies partitioning between thermal and statistical properties of entropy, yielding a more complete view of the evolutionary nature of the second law of thermodynamics. The ease of performing these operations is illustrated by three important chemical gas phase reactions, the reversible dissociation of the hydrogen molecules, lysis of water to hydrogen and oxygen and the reversible formation of ammonia from nitrogen and hydrogen. Employing the ergal also introduced by Clausius to define the reversible internal work to overcome molecular interactions plus the configurational internal work of negative Gibbs energy as a function of volume or pressure may provide a practical guide for managing risk in industrial processes and climate change at the global scale.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

The majority of investigations on microbial communities from various environments are presently built on culture-independent methods. Many studies point to the pivotal, selective role of primers targeting hypervariable regions of 16S rRNA in the metabarcoding of bacteria, including cyanobacterial communities. The selectivity of primers designed to amplify targeted regions of the 16S rRNA gene, which has been highlighted by many authors, limited effective amplification. Moreover, the type and specificity of the studied material can also negatively influence the results of 16S metabarcoding. Most of the studies of cyanobacterial communities have been performed for planktonic microbial communities that are often represented by common, well-studied species. In this study, we present the results of 16S metabarcoding analysis using three primer pairs - two already well-known and a third designed in this study - that amplify divergent regions of the 16S rRNA gene (V3-V4, V4-V6, V6) for benthic, microbial mat-forming cyanobacteria communities. Such communities can be a source of toxigenic cyanobacterial taxa and should be monitored with adequate primers. The comparison of three primer pairs suggested that those designed within the present study describe the structure and composition of highly heterogeneous cyanobacterial mats’ communities better than the others

Abstract: The Willows, belonging to the genus Salix, encompass a vast array of species and hybrids, totaling between 330 to 500 species along with approximately 200 hybrids. These plants are found across continents such as Africa, North America, Europe, and Asia, exhibiting diverse forms ranging from trees to shrubs and prostrate plants. Traditionally, Willows have been utilized in folk medicine due to their rich reservoir of biologically active compounds, with salicin being a notable example, serving as a prodrug for salicylic acid.The chemical composition of Willows is highly diverse, with 322 secondary metabolites identified thus far. These include various classes such as flavonoids (94 types encompassing flavonols, flavones, flavanones, isoflavones, flavan-3-ols like catechins and procyanidins, chalcones, dihydrochalcone, anthocyanins, and dihydroflavonols), phenolic glycosides (76), organic acids (28), non-phenolic glycosides (17), sterols, and terpenes (17), simple phenolics (13), lignans (7), as well as volatiles and fatty acids (69). This rich chemical di-versity underpins the various pharmacological activities exhibited by Willows. The pharmacological properties attributed to Willows are extensive and include analgesic, an-ti-inflammatory, antioxidant, anticancer, cytotoxic, antidiabetic, antimicrobial, antiobesity, neuroprotective, and hepatoprotective effects. These properties make Willows a subject of con-siderable interest in the fields of medicine and pharmacology. In summary, Willows represent a valuable natural resource with a diverse chemical composition and a wide range of pharmacological activities. This study aimed to enhance our comprehension of the medicinal characteristics of willow bark extract, focusing on its antimicrobial properties. This investigation holds significance in validating the traditional usage of willow bark and investi-gating its potential utility in contemporary medicine.

Global public health systems have continuously faced challenges from the advent of novel infectious illnesses, necessitating quick and efficient actions to stop their spread.First discovered in Saudi Arabia in 2012, Middle East respiratory syndrome (MERS) is a viral respiratory disorder caused by the Middle East respiratory syndrome coronavirus (MERS-CoV). Since then, the nation has reported most cases and fatalities related to this sickness, with occasional outbreaks happening in other nations and regions. Severe sickness and high mortality are caused by MERS-CoV, especially in older persons and those with underlying chronic conditions. Through intimate contact, the virus can spread from people to dromedary camels and vice versa. It has sparked multiple epidemics both domestically and abroad in the Middle East, raising the possibility of fatalities and widespread transmission, especially in susceptible groups. The Riyadh region was the main target of the most current MERS-CoV outbreak in Saudi Arabia, which began in 2023 and ended on September 1, 2023, with 312 confirmed cases and ninety-seven fatalities. With the use of published studies and their contributions to the field, we hope to present a thorough overview of the MERS-CoV outbreak in Saudi Arabia in this review of the literature, including its epidemiological investigation, public health response, impact, and lessons learned. In addition to highlighting the importance and continued relevance of this problem, our work suggests ways to lower the risk of MERS-CoV transmission and avert further outbreaks.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

The tribology behavior, tribofilm formation and structure evolution of polytetrafluoroethylene (PTFE) filled with α-Al2O3 and SiO2 nanoparticles during sliding against steel counterparts under different loads were studied. It is found that both composites exhibit good wear resistance across the pressure of 1 MPa to 10 MPa, with the α-Al2O3/PTFE composite demonstrates better performance stability compared to the SiO2/PTFE composite. The high wear resistance is attributed to the formation of tribofilms at the friction interface. For the α-Al2O3/PTFE, an island-like tribofilm is formed with a thickness ranging from 100 to 200 nm, while the tribofilm of the SiO2/PTFE composite is thinner, measuring approximately 50 to 100 nm, and manifest a striped pattern. The chemical composition, both at the surface and subsurface levels, as well as the morphology of the tribofilms were studied using FTIR spectrometry, X-Ray photoelectron spectroscopy (XPS), and FIB-TEM. It is found that the difference in thickness and microstructure of the tribofilms for the two composites is mainly due to the tribochemistry of the nanoparticles. The α-Al2O3 nanoparticle plays a "cohesion" role during the formation of the tribofilm, which facilitates the formation of a thicker, more uniform, and stronger adhered tribofilm on the metallic counterpart, making it more robust against higher shear stress.

Chemical process control relies on a tightly controlled, narrow range of margins for critical variables, ensuring process stability and safeguarding equipment from potential accidents. The availability of historical process data is limited to a specific setpoint of operation. This challenge raises issues for process monitoring in predicting and adjusting to deviations outside of the range of operational parameters. Therefore, this paper proposes simulation-assisted deep transfer learning for predicting and optimizing the final purity and production capacity of the glycerin purification process. The proposed network is trained by the simulation domain to generate a base feature extractor, which is then fine-tuned using few-shot learning techniques on the target learner to extend the working domain of the model beyond the historical practice. The result shows that the proposed model improved prediction performance by 99% in predicting water content and 79.72% in glycerin prediction over the conventional deep learning model. Additionally, the implementation of the proposed model identified the production and product quality improvement for enhancing the glycerin purification process.

A comprehensive kinetic model of the Fischer-Tropsch synthesis (FTS) is developed in a fixed bed reactor under operating conditions (temperature, 230–235°C, pressure, 20–25 bar, gas hourly space velocity, 4000–5000 cm³(STP)/h/g_catalyst ,H₂/CO feed molar ratio, 2.1) over a Co based catalyst. Reaction rate equations based on Eley-Rideal (ER) type model for initiation step and Langmuir-Hinshelwood-Hougen-Watson (LHHW) type model for propagation and termination steps of the FTS reactions have been considered and the readsorption of olefins were taken into account. The model that was reported in the literature was modified in order to explain many significant deviations from the ASF distribution. Optimum parameters have been obtained by Genetic Algorithms (GA). The calculated activation energies to produce n-paraffins and 1-olefins were in the range of 82.24 to 90.68 kJ/mol and 100.66 to 105.24 kJ/mol, respectively. The hydrocarbon distribution in FTS reactions was satisfactorily predicted particularly for paraffins.

Disease, trauma, and aging account for a significant number of clinical disorders. Regenerative medicine is emerging as a very promising therapeutic option. The design and development of new cell-customized biomaterials able to mimic ECM functionalities represent one of the major strategy to control the cell fate and stimulate tissue regeneration. Recently, hydrogels have received a considerable interest for their use in the modulation and control of cell fate during regeneration processes. Several synthetic bioresponsive hydrogels are being developed in order to facilitate cell-matrix and cell-cell interactions. In this review new strategies and future perspectives of such synthetic cell microenvironment will be highlighted.

A method based on ultra performance liquid chromatography with diode array detector (UPLC-DAD) was developed for quantitative analysis of five active compounds and chemical fingerprint analysis of Rosa rugosa. Ten batches of Rosa rugosa collected from different plantations in the Xinjiang region of China were used to establish the fingerprint. The feasibility and advantages of the used UPLC fingerprint were verified for its similarity evaluation by systematically comparing chromatograms with professional analytical software recommended by State Food and Drug Administration (SFDA) of China. In quantitative analysis, the five compounds showed good regression (R²=0.999 5) within the test ranges and the recovery of the method was in the range of 94.2–103.8%. The similarities of the fingerprints of 10 batches of the samples were more than 0.981. The developed UPLC fingerprint method is simple, reliable and validated for the quality control and identification of Rosa rugosa. Additionally, simultaneous quantification of five major bioactive ingredients in the Rosa rugosa samples was conducted to interpret the consistency of the quality test. The results indicated that the UPLC fingerprint as a characteristic distinguishing method combining similarity evaluation and quantification analysis, can be successfully used to assess the quality and to identify the authenticity of Rosa rugosa.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

Lysine plays a crucial role in promoting development, enhancing immune function, and improving the function of central nervous system tissues. The two configurational isomers of amino acids have significantly different effects. Currently, methods for chiral recognition of lysine all have drawbacks such as expensive equipment and complicated detection processes, whereas fluorescence analysis boasts high sensitivity, strong selectivity, and simple operation. In this study, we synthesized four novel Binaphthyl-Amine (BINAM)-based fluorescent probes capable of specifically identifying the L-configuration of lysine among the twenty amino acids constituting human proteins. The enantiomeric fluorescence enhancement ratio (ef or ΔIL/ΔID) reached up to 15.29, demonstrating high enantioselectivity. We also evaluated the probe's recognition ability under different pH, reaction times, and metal ion conditions, as well as the Limit of Detection of the probe. Our findings indicate that this probe is a highly stable tool for detecting chiral lysine.

In this study, the olive pomace was considered because of its importance in the environment. So, this study carried out to estimate the total nitrogen content and the fatty acids profile of olive pomace. The olive pomace samples were collected from Irbid, Jarash, Ajloun and Mafraq during the harvesting season 2014 to study the biochemical characteristics of fatty acid composition and the total nitrogen (TN) content. The total nitrogen content was determined by standard Kjeldahl method and the fatty acid profile was detected by gas chromatography (GC). The results show that the total nitrogen content ranged from (0.39 ± 0.0) to (0.62 ± 0.02) with statistically significant difference suggesting that the composition of matrices and their percentage may be responsible for composition of amendments. The calculated total protein percentage ranged between (2.43 ± 0.00) to (3.87 ± 0.17). Also, 13 different fatty acids were quantitatively profiled and quantitated. Oleic acid (C 18:1) was found to be the highest percentage of all other fatty acids and ranged between (59.03%) and (63.81%), moreover the C 18:1/C 18:2 (oil quality) was calculated and C.V% showed variation meaning that nutritional implication could affect the oxidative stability of oils. In conclusion, OP by-product could give a sustainable and alternative-cheap source for fertilizers, pharmaceutical industries, cosmetics and other industries.

Several bio-actors are involved in the occurrence of leishmaniasis, which is made too complex for prevention and control options. Currently, all forms of leishmaniasis are being treated with chemical drugs, which have limitations and adverse effects on patients. Searching the bioactive molecules from plant sources allows the development of a novel drug. The essential oil and solvent extract of the roots of E. kebericho showed antileishmanial activity. But looking for biological activities of the isolated active ingredient from tubers of E. kebericho was scant. Thus, the isolation of the leishmanicidal compound from the roots of E. kebericho through a bioassay-guided technique was an aim of this work. Dehydrocostus lactone showed doubled potent than the standard drug miltefosine on leishmanicidal activities against L. major and L. tropica. Besides, the broad-spectrum biological activities of dehydrocostus lactone could be a potential drug candidate for co-infected patients caused by an association of leishmania and another pathogen.

Synergistic effects between reactions, reagents and catalysts can lead to minor heats of reaction and occur as an inherent result of multi-component reactions (MCRs) and their extensions. They enable syntheses to be performed at a low energy level and the number of synthesis steps to be drastically reduced in comparison with ‘classical’ two-component reactions. The very high potential for variability, diversity and complexity of MCRs additionally generates an extremely diverse range of products, thus bringing us closer to the aim of being able to produce tailor-made and extremely low-priced materials, drugs and libraries.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

Nanocelluloses have gained significant attention in recent years due to singular properties (good biocompatibility, high optical transparency and mechanical strength, large specific surface area and good film-forming ability) and wide-ranging applications (paper, food packaging, textiles, electronics and biomedical). This article is a comprehensive review of nanocelluloses from the preparation methods to their applications in conservation and restoration of historical paper documents. The novelty lies in the information collected about nanocelluloses as renewable, environmentally friendly and sustainable materials in the field of preservation of cultural heritage as an alternative to conventional methods. Several studies have demonstrated that nanocelluloses, with or without other particles, impart to the paper documents excellent optical and mechanical properties, very good stability against temperature and humidity aging, stronger antibacterial and antifungal activity, high protection to UV light and do not require additional adhesive.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Background: Amyloid beta peptides (Aβ) have been identified as the main pathogenic agents in Alzheimer’s disease (AD). Soluble Aβ oligomers, rather than monomer or insoluble amyloid fibrils, show membrane-binding capacity to red blood cells (RBCs) and trigger several morphological and functional alterations in RBCs that can result in impaired oxygen transport and delivery. Since bioactive lipids have been recently proposed as potent protective agents against Aβ toxicity, we investigated the role of sphingosine-1-phosphate (S1P) in signaling pathways involved in the mechanism underlying ATP release in Aβ-treated RBCs. Methods: In RBCs following different treatments, ATP, 2,3 DPG, cAMP levels, and caspase 3 activity were determined by spectrophotometric and immunoassay. Results: S1P rescued the inhibition of ATP release from RBCs triggered by Aβ through a mechanism involving caspase-3 and restoring 2,3 DPG and cAMP levels within the cell. Conclusions: These findings reveal the molecular basis of S1P protection against Aβ in RBCs and suggest new therapeutic avenues in AD.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

Development of the self-cleaning and anti-fogging superhydrophobic coating for aluminum surfaces which is durable in the aggressive conditions has raised tremendous interest in materials science. In this work, by employing chemical etching technique with mixture of hydrochloric and nitric acid, followed by passivation with lauric acid, superhydrophobic aluminum surface was synthesized. The surface morphology analysis reveals the presence of rough microstructures on coated aluminium surface. Superhydrophobicity with water contact angle of 170 ± 3.9° and sliding angle of 4 ± 0.5° is achieved. Surface bounces off the high speed water jet, indicating excellent water-repellent nature of coating. It is also continuously floated on water surface for several weeks, showing excellent buoyancy nature. Additionally, coating maintains its superhydrophobicity after undergoing 100 cycles of adhesive tape peeling test. Its superhydrophobic nature withstands 90° and 180° bending, and repeated folding and de-folding. Coating exhibits the excellent self-cleaning property. In low temperature condensation test, almost no accumulation of water drops on the surface, showing the excellent anti-fogging property of coating. This approach can be applied to any size and shape of aluminium surface and hence has great industrial applications.

A techno-economic model was developed to investigate the influence of components on the system costs of redox flow batteries. Sensitivity analyses were carried out based on a example of a 10 kW/120 kWh vanadium redox flow battery system and the costs of the individual components were analyzed. Particular consideration was given to the influence of material costs and resistances of bipolar plates and energy storage media as well as voltages and electric currents. Based on the developed model it was possible to formulate statements about the targeted optimization of existing battery systems and general aspects for future developments of redox flow batteries.

Residual sugars (RS) in wine are the sugars that remain in a wine after fermentation is complete. In some wine styles, such as semi-dry wines, the accurate measurement of the RS concentration is critical for both qualitative and legislative reasons. Brix, measured by a simple refractometer, can give a good estimation of the RS concentration in the must, but during fermentation, the presence of alcohol leads to inaccurate sugar measurements. In order to measure the RS accurately, other more precise techniques are used, most of which are expensive or require professional skills. Therefore, novel approaches for rapid, easy, and practical measurements for estimating the sugar content were suggested over the years. However, most of these methods do not supply an actual measurement of RS but rather give brix values, and those that measure RS involve special equipment, which is less relevant for small wineries. This study suggests a novel model for predicting and controlling the wine's residual sugar. The data the model uses is the initial brix of the must before fermentation and its density during fermentation. The model was created by measuring actual residual sugars during the fermentation of natural and synthetic musts, with various degrees of initial brix levels, while simultaneously measuring their densities and correlating the two measurements. Linear regression between the residual sugar of the wine and its density was obtained for all treatments and repetitions (i.e., different values of must initial brix) with R² values above 0.97. Using the model, one can calculate (before commencing the fermentation) the density values at which the fermentation will reach a particular desired residual sugar value for a specific initial brix level; the model is applicable for the fermentation conditions used in this work, i.e., brix levels of 18-27˚Bx, Saccharomyces cerevisiae strains (fx-33 and fx-10) in common conditions of fermentation regarding temperature and aeration.

In our study we investigated the accelerated aging process of PLA under 253.7 nm UV-C irradiation with the use of GPC, NMR, FTIR, DSC methods and formal kinetic analysis. The results of GPC and DSC indicated a significant degree of destructive changes in PLA macromol-ecules, while spectroscopic methods NMR and FTIR showed maintenance of PLA main structural elements even after a long time of UV exposure. In addition to that, the GPC method displayed the formation of a high-molecular fraction starting from 24 hours of irradiation, and an increase in its content after 144 hours of experiment. It has been showed for the first time that a distinctive feature of prolonged UV exposure is the occurrence of intra- and intermolecular radical recom-bination reactions, leading to the formation of a high-molecular fraction of PLA decomposition products. This causes the observed slowdown of the photolysis process. It was concluded that photolysis of PLA is a complex of physicochemical processes, the mechanism of which depends on morphological changes in a solid phase of the polymer under UV radiation.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

Allylbenzenes (apiol, dillapiol, myristicin and allyltetramethoxybenzene) are individual components of plant essential oils that demonstrate antitumor activity, as well as enhancing effect on cytotoxic drugs such as paclitaxel, doxorubicin, cisplatin, etc. Triphenylphosphine (PPh3) derivatives of allylbenzenes are 2-3 orders of magnitude more potent than allylbenzenes in terms of IC50. Inhibition of efflux pumps has been reported for allylbenzenes, and PPh3 moiety is deemed to be responsible for preferential mitochondrial accumulation and depolarization of mitochondrial membranes. However, due to poor solubility the practical use of these substances has never been an option. Cyclodextrin-based (CD) molecular containers suggested here provided solubilization of allylbenzenes and its PPh3-derivatives. So, in this study we have observed an increase antitumor activity of paclitaxel in the presence of PPh3-derivatives adjuvants by an order of magnitude (in terms of IC50) against adenocarcinomic human alveolar basal epithelial cells A549. At the same time, they are quite powerful cytostatics themselves against A549 cells. On the other hand, the cytotoxic formulations developed show pronounced selectivity of the antiproliferation activity: high against tumor cells line (A549) and low toxicity of these composition was demonstrated on normal cells HEK293T, red blood cells, and sea urchin embryos (a model close to the human genome). On non-cancer HEK293T cells, it was shown that PPh3-derivatives of allylbenzenes at a concentration of 100 µM cause the death of about 20% of cells, while on A549 cancer cells, 85% of cells die. PPh3 derivatives of allylbenzenes, when solubilized in CD molecular containers, show remarkable potential as adjuvants to some of the widely used cytotoxic drugs.

The 5-hydroxymethylfurfural (HMF) is a six-carbon heterocyclic organic compound with two substituents an aldehyde group and an alcohol group. It is formed from saccharides as a result of two reactions: the Maillard reaction and the caramelization of saccharides. It has both a negative and a positive effect on the human body, which makes it, even more, an attractive research object. The objective of the study was to determine HMF content in honey samples available on the Polish market using three varied methods and compare the results obtained. The methodology used included: two spectrophotometric methods (by White and Winkler) and the HMF determination method based on the LC-MS/MS technique developed uniquely for this study. The determined HMF content in all tested honey samples did not exceed the applicable standard. All results are within the scope of the European Council Directive 2001/110/EC of 20 December 2001, i.e. they do not exceed HMF content in honey, which is 40 mg/kg.

After UV excitation, gas phase thymine returns to ground state in 5 to 7 ps, showing multiple time constants. There is no consensus on the assignment of these processes, with a dispute between models claiming that thymine is trapped either in the first (S1) or in the second (S2) excited states. In the present study, nonadiabatic dynamics simulation of thymine is performed on the basis of ADC(2) surfaces, to understand the role of dynamic electron correlation on the deactivation pathways. The results show that trapping in S2 is strongly reduced in comparison to previous simulations considering only non-dynamic electron correlation on CASSCF surfaces. The reason for the difference is traced back to the energetic cost for formation of a CO p bond in S2.

MgAl oxide coatings containing MgO and MgAl2O4 phases were doped with CeO2 particles using plasma electrolytic oxidation (PEO) of AZ31 magnesium alloy in 5 g/L NaAlO2 water solution, with CeO2 particles added at concentrations up to 8 g/L. They underwent extensive inve-stigation into their morphology, chemical and phase compositions, and most importantly, photoluminescent (PL) properties and photocatalytic-activity (PA) in photodegradation of methyl orange (10 cm3 of 8 mg/L). The concentration of CeO2 particles in the aluminate electrolyte influences the amount of CeO2 particles incorporated into MgAl oxide coatings, but CeO2 particles have no signi-ficant effect on the surface morphology, thickness, or phase structure of the coatings. The PL emi- ssion spectrum of MgAl oxide coating is divided into two bands: one in the 350-600 nm range related to structural defects in MgO, and another much more intense in the 600-775 nm range attributed to F+ centres in MgAl2O4. Incorporated CeO2 particles do not have a significant effect on the PL intensity of the band in the red spectral region, but the PL intensity of the first band increases with the concentration of CeO2 particles. PA of MgAl/CeO2 oxide coatings is higher than that of pure MgAl oxide coatings. The highest PA was observed for MgAl/CeO2 oxide coatings formed in aluminate electrolytes with the addition of 2 g/L of CeO2 particles. The MgAl/CeO2 oxide coatings remained chemically and physically stable across multiple cycles, indicating their potential for applications.

There are unsolved problems related to inflation, gravity, dark matter, dark energy, missing antimatter, and the birth of the universe. Some of them can be better answered by assuming the existence of aether and hypoatoms. Both were created during the inflation in the very early universe. While aether forms vacuum, hypoatoms, composed of both matter and antimatter and believed to be neutrinos, form all observable matter. In vacuum, aether exists between the particle-antiparticle dark matter form and the dark energy form in a dynamic equilibrium: A + A-bar = gamma + gamma. The same reaction stabilizes hypoatoms and generates a 3-dimensional sink flow of aether that causes gravity. Based on the hypoatom structure, the singularity does not exist inside a black hole; the core of the black hole is a hypoatom star or neutrino star. By gaining enough mass, ca. 3 X 10²² M_sun, to exceed neutrino degeneracy pressure, the black hole collapses or annihilates into the singularity, thus turning itself into a white hole or a Big Bang. The universe is anisotropic. Its center, or where the Big Bang happened, is at 0.66^+0.03_-0.01 times the radius of the observable universe at Galactic coordinates (l, b) = (286⁺¹⁰_-10, -43⁺⁷_-6). If we look from the Local Group to the center of the universe, the universe is rotating clockwise.

There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

A heterograft copolymer with an alginate backbone, hetero-grafted by polymer pendant chains displaying different Lower Critical Solution Temperatures (LCSTs), combined with a pH-responsive Poly(2-vinyl pyridine)-b-poly(ethylene oxide) (P2VP-b-PEO) diblock copolymer forming micellar nanoparticles, was investigated in aqueous media at various pH. Due to its thermoresponsive side chains, the copolymer forms hydrogels with thermo–induced sol–gel transition, above a critical temperature, Tgel (thermo–thickening). However, by lowering pH of the medium in acidic regime, a remarkable increase of the elasticity of the formulation was observed. This effect was more pronounced in low temperatures (below Tgel) suggesting secondary physical crosslinking, which induces significant changes in the hydrogel thermoresponsiveness, transforming the sol–gel transition to soft gel–strong gel. Moreover, the onset of thermothickening shifted to lower temperatures followed by broadening of the transition zone, implying intermolecular interactions between the uncharged alginate backbone with the PNIPAM side chains, likely through H–bonding. The shear–thinning behavior of the soft gel in low temperatures provides injectability, which allows 3D–printing potential applications. Furthermore, the heterograft copolymer/nanoparticles composite hydrogel, encapsulating a model hydrophobic drug in the hydrophobic cores of the nanoparticles, was evaluated as pH-responsive drug delivery system. The presented tunable drug delivery system might be useful for biomedical potential applications.

The photosystem I (PSI) of the green alga Chlamydomonas reinhardtii associates with 10 light-harvesting proteins (LHCI) to form the PSI-LHCI complex. Binding of LHCII to PSI may also occur and is controlled by a process called state transitions. Hereby, two LHCII trimers bind to the PSAL, PSAH and PSAO side of PSI to produce the PSI-LHCI-LHCII complex. In this work, we took advantage of chemical crosslinking of proteins in conjunction with mass spectrometry to identify protein-protein interactions between the light-harvesting proteins of PSI and PSII. We detected binding of LHCBM proteins to the LHCA1-PSAG side of PSI and identified protein-protein interactions of LHCSR3 with LHCA5 and LHCA3. Our data indicate that the binding of LHCII to PSI is more versatile as anticipated and reveal that LHCSR3 likely regulates excitation energy transfer to the PSI core via LHCA5/LHCA3.

Silybin is a natural compound extensively studied for its hepatoprotective, neuroprotective and anti-cancer properties. Envisioning the enhancement of silybin potential by suitable modifications in its chemical structure, here, a series of new 7-O alkyl silybins derivatives were synthesized by Mitsunobu reaction starting from the silybins and tyrosol-based phenols, such as tyrosol (TYR, 3), 3-methoxytyrosol (MTYR, 4) and 3-hydroxytyrosol (HTYR, 5). This research sought to explore the antioxidant and anticancer properties of new eighteen derivatives and their mechanisms. In particular, the antioxidant properties of new derivatives outlined by DPPH assay, showed a very pronounced activity depending on the tyrosyl moiety (HTYR>MTYR>>TYR). A significant contribution of the HTYR moiety was observed for silybins and 2,3-dehydro-silybin based derivatives. According to the very potent antioxidant activity, 2,3-dehydro-silybin derivatives 15ab, 15a and 15b exerted the most potent anticancer activity in human prostate cancer PC-3 cells. Furthermore, flow cytometric analysis for cell cycle and apoptosis revealed that 15ab, 15a and 15b induce strong G1 phase arrest and increase late apoptotic population in PC-3 cells. Additionally, western blotting for apoptotic marker cleaved caspase-3 confirmed apoptosis induction by these silybin derivatives in PC-3 cells. These findings hold significant importance in the investigation of anticancer properties of silybin derivatives and strongly encourage swift investigation in pre-clinical models and clinical trials.

Familial Mediterranean fever (FMF) is a systemic autoinflammatory disorder caused by inherited mutations in the MEFV (Mediterranean FeVer) gene located on chromosome 16 (16p13.3) and coding pyrin protein. Despite the existing data on MEFV mutations, the exact mechanism of their effect on the development of pathological processes leading to autoinflammation observed in FMF, remains unclear. Induced pluripotent stem cells (iPSCs) are considered an important tool for studying the molecular genetic mechanisms of various diseases due to their ability to differentiate into any cell type, including macrophages, which contribute to the development of FMF. In this study, we developed iPSCs of an Armenian patient with FMF having M694V, p.(Met694Val) (c.2080A>G, rs61752717) pathogenic mutation in exon 10 of the MEFV gene. As a result of direct differentiation, macrophages expressing CD14 and CD45 surface markers were obtained. In addition, we found that the morphology of patient macrophages derived from iPSCs with MEFV mutation was significantly different from that of differentiated from iPSCs of a healthy donor carrying wild-type MEFV gene.

We construct a Bayesian estimator for the dilution of a wastewater sample. When wastewater is diluted by rainwater an estimate of the level of dilution is required if we are to normalise sample measurements of disease markers such as SARS-CoV-2 RNA. We consider the situation where flow measurements are available, but will regularly be unreliable because of the action of combined sewer outflows (CSOs) and wastewater storage tanks, which divert wastewater away from treatment plants when the flow is excessive. However, we also have proxies for the flow from various chemical markers (e.g.\ phosphate, ammonium, electrical conductivity), whose level per unit of population is fixed. The new flow estimator has multiple advantages compared to existing procedures: credible intervals for the estimates; optimal weighting of the chemical markers; systematic handling of missing and censored values; and model based smoothing without lags.

Vitamin D3 deficiency is a global phenomenon, which can be coped with supplementation and food fortification. However, vitamin D3 bioaccessibility may depend on factors, such as matrix composition and interactions throughout the gastrointestinal tract. This research focused on the effect of different matrices on vitamin D3 content during digestion, and the effect of pH on its bioaccessibility. The INFOGEST protocol was employed to simulate digestion. Three different types of commercial supplements, two foods naturally rich in vitamin D3, and three fortified foods were investigated. High-Performance Liquid Chromatography was used to determine the vitamin D3 initial content in supplements and foods, as well as after each digestion stage. Results indicated that foods exhibited higher bioaccessibility indices compared to supplements, and a higher percentage retention at the end of the gastric phase. The pH study revealed a positive correlation between increased gastric pH and the corresponding content of vitamin D3. Interestingly, exposing the matrix to low pH during the gastric phase resulted in an increased intestinal content of D3. Vitamin D3 is more bioaccessible from foods than supplements, and its bioaccessibility is susceptible to changes in gastric pH. Fasting conditions (i.e. gastric pH=1) enhances vitamin’s bioaccessibility.

Background: Long-range transport of dust aerosol has intense impacts on the atmospheric environment over wide areas. Methods: The annual and seasonal changes in meteorological parameters associated with the occurrence of dust storms were studied. The features of an intense dust storm and its transport characteristics were studied during June 7th to June 9th 2010 in Ahvaz city. Temporal and spatial distribution of Middle Eastern dust storm event was analyzed by models of HYSPLIT and WRF/Chem, and in- situ observations. Results: A disagreement between the occurrences of dust storms, temperature, relative humidity and rainfall, show the major source of dust storms over Ahvaz city are neighboring countries. Using HYSPLIT results, the dust particles are mainly transported from north western region of Iraq and eastern Syria to downward areas including Ahvaz city. The arrived Dust aerosols mixed with local anthropogenic emissions, led to the highest PM10 concentration of 4200 ppm. The model results were found to well reproduce temporal and spatial distribution of mineral dust concentrations according to in-situ measurements. Conclusion: The performance of WRF/Chem was acceptable for simulation of temporal and spatial distributions of dust storm events. Therefore, it can be taken as a reference in daily air quality forecasting.

This research aims to deepen the understanding of the relationship between conductivity and morphology in polypyrrole (PPy) via a comparison of the bipolaron to polaron ratios with a focus on the C-H deformation area. PPy samples were synthesized with different surfactants: sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and tween 80 (TW). The study revealed that SDS significantly altered the bipolaron and polaron in C-H deformation region and showed higher conductivity than other surfactants. Notably, the morphological shifts to a sheet-like structure when using ammonium sulfate (APS) contrasted with the particle-like form observed with ferric chloride (FeCl3). These results showed that if the oxidant changed, the bi-polaron and polaron ratios in C-H deformation were unrelated to PPy morphology. However, this work showed a consistent relationship between SDS use, the bipolaron and polaron ratios in the C-H deformation, and the conductivity properties. Moreover, the natural positive charge of PPy and negatively charged SDS molecules may lead to an electrostatic interaction between PPy and SDS. This work assumes that this interaction might cause the transformation of polaron to bipolaron in the C-H deformation region, resulting in improved conductivity of PPy. This work offers more support for the future investigation of PPy characteristics.

Organic fertilizer application in agricultural land is known to improve soil microbial processes, fertility, and yield. In particular, stable changes in soil chemical composition through multi-year fertilization of organic fertilizers are thought to cause changes in the microbial community. Here, the effects of oil cake amendments (OC) on soil bacterial diversity, community profile and enzyme activity were evaluated and compared to those amended with chemical fertilizer (NPK). The comparison of diversity indices between OC and NPK amended soils shows that application of oil cake has increased microbial diversity potentially with an increase in the number of different microbial groups. The ordination plot distinguished and clustered both treatments showing differential effects of soils chemical factors on the microbial communities of each treatment. Proteobacteria, Verrucomicrobia and Bacteriodetes were significantly abundant in OC amended soil than in the NPK received soil, indicating alterations in community structure, composition, and diversity con-current to the changes in pH, Ca and Mg contents of the soil. These shifts in bacterial community structure and composition could also be observed from the phylum to the genus level in both NPK and OC amended soils partially explained by differences in soil chemical factors. The OC soil compared to the NPK amended soil also contain significantly higher abundance of predicted genes corresponding to enzymes related to biogeochemical cycling, decomposition and plant growth promotion. Collectively, these results support the use of an unconventional organic fertilizer positively altering bacterial populations in jujube orchards. The application of oil cake-based organic fertilizer improved microbial diversity and enhanced potential ecosystem functions related to bio-geochemical cycles, mineralization and plant growth promotion.

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

Radical reactions are powerful in the synthesis of diverse molecular scaffolds bearing functional groups. In pervious review articles, we have presented 1,2-difunctionalizations, remote 1,3-, 1,4-, 1,5-, 1,6- and 1,7-difunctionalizations, and addition followed by cyclization reactions. Presents in this paper are radical cyclization followed by the second functionalization reactions. The second functionalization could be realized by atom transfer reactions, radical or transition metal-assisted coupling reactions, and reactions with neutral molecules, cationic and anionic species.

This overview initially describes insect immune reactions and then brings together present knowledge of the interactions of vector insects with their invading parasites and pathogens. It is a way of introducing this special issue with subsequent papers presenting the latest details of these interactions in each particular group of vectors. Hopefully, this paper will fill a void in the literature since brief descriptions of vector immunity have now been brought together in one publication and could form a starting point for those interested and new to this important area. Descriptions are given on the immune reactions of mosquitoes, blackflies, sandflies, tsetse flies, lice, fleas and triatomine bugs. Cellular and humoral defences are described separately but emphasis is made on the co-operation of these processes in the completed immune response. The paper also emphasises the need of great care in extracting haemocytes for subsequent study as appreciation of their fragile nature is sometimes overlooked with non-sterile media, smearing techniques and excessive centrifugation sometimes used. The potential vital role of eicosanoids in the instigation of many of the immune reactions described is also discussed. Finally, the priming of the immune system, mainly in mosquitoes, is considered and one possible mechanism is presented

Recent interest in intestinal hormones has risen with the idea that they modulate glucose tolerance and food intake through a variety of mechanisms, and such hormones like peptide YY (PYY), ghrelin, glucagon-like peptide (GLP)-1 and 2, and cholecystokinin (CKK) are therefore excellent therapeutic candidates for the treatment of diabetes and obesity. Furthermore, in the recent years, multiple studies suggest that the microbiota is critically important for normal host functions, while impaired host microbiota interactions contribute to the pathogenesis of numerous common metabolic disorders. In this study, we considered the nutraceutical effects of β-glucans added to pasta at the concentration of 6g\100g. Ten participants have been recruited and hematochemical analyses and intestinal hormones tests have been performed before and after 30 days of pasta intake. Stool specimens have been studied for Lactobacillus Fermentum, Lactobacillus acidophilus, Lactobacillus salivarius, Bifidobacterium longum, and Enterococcus faecium presence before and after 30 days of nutritional intervention. After 30 days of regular intake of pasta enriched by β-glucans results have been evaluated. In conclusion, pasta prepared from barley flour enriched with β-glucans at 6% exhibit promising responses on glucose metabolism, on intestinal hormones responses and on microbiota modification.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

The relationship between pangolin-CoV and SARS-CoV-2 has been a subject of debate. Further evidence of a special relationship between the two viruses can be found by the fact that all known COVID-19 viruses have abnormally hard outer shell (low M disorder; i.e., low content of intrinsically disordered residues in the membrane (M) protein) that so far was found in CoVs associated with burrowing animals, such as rabbits and pangolins, in which transmission involves virus remaining in buried feces for a long time. While a hard outer shell is necessary for viral survival, a harder inner shell could also help. For this reason, the N disorder range of pangolin-CoVs, not bat-CoVs, more closely matches that of SARS-CoV-2 especially when Omicron is included. The low N disorder (i.e., low content of intrinsically disordered residues in the nucleocapsid (N) protein), first observed in pangolin-CoV-2017 amd later in Omicron, is associated with attenuation according to the Shell-Disorder-Model. Our experimental study revealed that pangolin-CoV-2017 and SARS-CoV-2 Omicron (XBB.1.16 subvariant) show similar attenuations with respect to viral growth and plaque formation. Subtle differences have been observed that are consistent with disorder-centric computational analysis.

Helical (frontier) molecular orbitals [Chem. Sci. 2013, 4, 4278] have been reported almost a decade ago. Yet, helical molecular spin densities [Mol. Phys. 2022, e2157774] have been observed by us only very recently. In this work, we have observed that some chiral boron clusters (B–16, B–20, B–24, and B–28) can simultaneously have helical molecular orbitals and helical spin densities. To our best knowledge, it is the first time we have discovered that inorganic boron clusters assume such an unprecedented property. We have unambiguously unraveled that it is chiral Jahn-Teller distortion of quasi-planar boron clusters that drives the formation of helical molecular spin densities. More interestingly, we have shown that elongation/enhancement of helical molecular orbitals can be achieved by simply adding more building blocks via a linker. Aromaticity properties of these boron clusters are also discussed. Implication of this work is straightforward that boron clusters may find potential applications in spintronics, such as molecular magnets.

Abstract: We present a technological analysis of the architectonic complex associated with a firing structure (locally named fogón) on top of the Pirámide Mayor, the largest pyramid in Caral. This Archaic Period society flourished between ca 2,700 and 2,000 cal B.C. and was located near the Pacific Ocean on the north-central coast of present-day Peru. All approaches employed in this study demonstrated that the corridor with antechamber and duct on top of Pirámide Mayor of Caral was a sophisticated ventilation system capable of providing between 3,000 and 18,000 liters of air per minute for combustion in the attached fogón. The analysis indicates that ventilating the fogón must have been a major consideration in deciding a) the construction of the pyramid, b) locating the structure at the edge of a natural alluvial terrace, and c) orientating the pyramid towards the then contemporary prevailing winds. Results from the analysis of this fogón support practical decisions made by the builders and challenge the assumption that religion or politics were the only considerations in American pyramid building. It also indicates that a complex device, capable to delivering the considerable airflows reported in this study was within the reach of an archaic society in ancient Peru. The application of this structure to the production of a remarkably high thermal output and its implications on the knowledge of ancient Americans will be discussed in a following companion article.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

Background: The workplace burnout syndrome is often associated with particular aspects of certain job positions, especially those which entail working with people with special needs. The burnout syndrome in healthcare jobs is a serious problem which has grown into an epidemic among healthcare workers and associates. Objectives: The aim of this research is to assess the presence of stress and burnout syndrome at work with healthcare workers, expert workers, professional associates and associates in social service institutions in Belgrade. Material and Methods: This research has been conducted in the form of a cross-sectional study of a representative sample in social institutions in Belgrade. It has been conducted from March to the end of June of 2023. The sample of the study had 491 participants. The questionnaires used were a structured instrument with social-demographic and social-economic characteristics, workplace characteristics, life style characteristics, and the following questionnaires: DASS-21, Copenhagen, Brief Resilience Scale, and Brief Resilient Coping Scale. Results: The end results indicate the following to be significant risk factors for the occurrence of workplace burnout syndrome: overtime (OR=2.62; CI=1.50-4.56), BRS average score (OR=0.28; CI=0.17-0.44), DASS21 D heightened depression (OR=2.09; CI=1.1-4.04), DASS21 A heightened anxiety (OR=2.38; CI=1.34-4.21), DASS21 S heightened stress (OR=2.08; CI=1.11-3.89). The only protective risk factor which stood out was the self-assessment of health levels (OR=0.60; CI=0.42-0.85). Conclusion: Overtime is a significant predictor of workplace burnout. Apart from it, other significant predictors of workplace burnout were heightened depression, anxiety, and stress levels.

Background: The Coronavirus Disease 2019 (COVID-19) pandemic presented a new challenge in modern medicine. The development of vaccines was followed by massive population vaccinations. A few reports on post-vaccination allergic reactions have made patients and medical personnel uneasy as to anti-COVID-19 vaccines’ allergising potential. Most of the studies in this area to date have been small, and some that were based on global databases skipped most of the allergic diseases and concentrated only on anaphylaxis. We aimed to analyse the incidence of serious allergic reactions based on the EudraVigilance (EV) database, regardless of the reported symptoms and allergy mechanism. Methods: The total number of administrated vaccine doses was extracted on the 5th October 2023 from Vaccine Tracker and included all administrations since vaccinations began in the European Economic Area (EEA). Data on serious allergic reactions to COVID-19 vaccines was extracted from the EudraVigilance database with the same time point. The code names of 147 allergic symptoms or diseases were used. Results: The frequency of serious allergic reactions per 100,000 administered vaccine doses was 1.53 for Comirnaty, 2.16 for Spikevax, 88.6 for Vaxzevria, 2.11 for Janssen, 7.9 for Novavax, 13.3 for VidPrevtyn Beta and 3.1 for Valneva. The most prevalent reported reactions were oedema (0.46) and anaphylaxis (0.40). Only 6% of these reactions were delayed hypersensitivity-oriented. Conclusions: The overall frequency of potential serious allergic reactions to COVID-19 is very rare. Therefore, COVID-19 vaccines seem to be safe for human use. The lowest frequency of allergic reaction was observed for Comirnaty and the highest for Vaxzevria.

To investigate the bioactivities of fresh garlic and its processed product, black garlic, we conducted comparative analyses of antioxidant, anti-inflammatory, innate immune activation and anti-cancer activities, in addition to chemical composition (sugar, amino acid, polyphenol contents) of these materials. Simultaneous assay using neutrophil-like cells showed that fresh garlic exhibited antioxidant and innate immunostimulatory activities, whereas black garlic displayed a potent anti-inflammatory effect. The antioxidant activity index was correlated with phenol and flavonoid contents, while the innate immunostimulatory activity was correlated with fructan content. Furthermore, some black garlics with low fructose content were found to inhibit the proliferation of UM-UC-3 cancer cells, while other black garlics rich in fructose increased UM-UC-3 cell proliferation. It was shown that the thermal processing steps of fresh garlic could change the composition of sugars, antioxidants, and amino acids, which have different effects on neutrophil-like cells and UM-UC-3 cells, as well as on bioactivities.