Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (<0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

Deep learning (DL) algorithms used for DOTATATE PET lesion detection typically require large, well-annotated training datasets. These are difficult to obtain due to low incidence of gastroenteopancreatic neuroendocrine tumors (GEP-NETs), and the high cost of manual annotation. Furthermore, networks trained and tested with data acquired from site specific PET/CT instrumentation, acquisition and processing protocols have reduced performance when tested with offsite data. This lack of generalizability requires even larger, more diverse training datasets. The objective of this study is to investigate the feasibility of improving DL algorithm performance by better matching the background noise in training datasets to higher noise, out-of-domain testing datasets. 68Ga-DOTATATE PET/CT datasets were obtained from two scanners: Scanner1, a state-of-the-art digital PET/CT (GE DMI PET/CT; n=83 subjects), and Scanner2, an older-generation analog PET/CT (GE STE; n=123 subjects). Set1, the data set from Scanner1 was reconstructed with standard clinical parameters (5 minutes; Q.Clear) and list-mode reconstructions (VPFXS 2, 3, 4, and 5-minutes). Set2, data from Scanner2, representing out-of-domain clinical scans, used standard iterative reconstruction (5 minutes; OSEM). Reconstructed datasets were divided into training, validation, and testing datasets in a 60%, 20%, 20% proportion, and a deep neural network was trained with each: Network1 for Scanner1 and Network2 for Scanner2. DL performance (Network1) was tested with out-of-domain test data (Set2). To evaluate the effect of training sample size, we tested DL model performance using a fraction (25%, 50%, and 75%) of Set1 for training. Scanner1, list-mode 2-minute reconstructed data demonstrated the most similar noise level compared that of Set2, resulting in the best performance (F1=0.713). This was not significantly different compared to the highest performance, upper-bound limit using in-domain training for Network2 (F1=0.755; p-value=0.103). Regarding sample size, the F1 score significantly increased from 25% training data (F1=0.478) to 100% training data (F1=0.713; p<0.001). List-mode data from modern PET scanners can be reconstructed to better match the noise properties of older scanners. Using existing data and their associated annotations dramatically reduces the cost and effort in generating these datasets, and significantly improves the performance of existing DL algorithms. List-mode reconstructions can provide an efficient, low-cost method to improve DL algorithm generalizability.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

Responding to changing value creation processes in the sheet metal working sec-tor, where the complexity and interchangeability of products challenge traditional dif-ferentiation strategies, this empirical analysis explores integrating service-oriented and data-driven business models as new paths to ensure competitiveness, especially for small and medium-sized enterprises (SMEs). This study aims to capture the current state and challenges associated with the implementation of these business models in this sector. The research was conducted through semi-structured interviews with SMEs in the industry. The findings indicate that service-oriented and data-driven business models are not yet widely adopted and that manufacturing companies re-quire support in their implementation. Fields of action were identified for the industry. These are "Creating awareness and understanding", "Recognizing added value", "In-creasing company maturity" and "Understanding the change process". Cooperation between science and industry is essential in tackling these fields of action to ensure the successful integration of such business models in manufacturing companies. This pa-per identifies challenges in the fields of action that companies must address through a structured approach promoting awareness, recognizing value, improving organiza-tional maturity, and understanding the change process to successfully implement ser-vice-oriented and data-driven business models.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

Mesenchymal stem cells due to their multipotent ability are considered one of the best candidates to be used in regenerative medicine. The most used source of those stem cells long the last decades was the bone marrow, despite its limited cell resources and the painful and very invasive surgical treatment. Therefore, the scientific community investigated many alternative sources for the harvesting of these stem cell subpopulations. Adipose tissue attracted the biggest interest thanks to special features, such as great tissue abundance, easy availability, and in the end the large amount of positive mesenchymal stem cells. Once it was verified that these stem cell subpopulations possess the same bone marrow differentiation potential, it became evident that they would be the ideal candidate to be used in regenerative and tissue engineering applications. Even the regenerative use of these cells long become a sensitive point because not all the acquired phenotypes resulted in the best source for plastic procedures. As documented in the literature, the ideal fillers for regenerative is represented by stem cell population. Therefore, it became crucial to investigate any kind of biological mechanism on the differentiative ability of those mesenchymal stem cells, especially their regulative factors. One of the most studied and important regulators are the miRNAs. Indeed, miRNA play a crucial role in the differentiation process of adipose stem cell cultures isolated from patients or obtained by commercial cell lines toward osteocytes, chondrocytes, and adipocytes differentiated populations.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

In this paper, the Hafele‐Keating experiment and the geostationary orbit satellite of related physics problems of are analyzed and discussed in detail. If researchers read the paper and think about it, It will be found that the Hafele‐Keating experiment and the geostationary satellite problem prove that some of the core ideas and theories of relativity are seriously wrong. Isnʹt that a very serious problem in physics? Canʹt this cause the academic circles to pay great attention to it? Isnʹt this worthy of in‐depth analysis and research? The core of the paper is to point out that there are problems with the space concept and the reference system theory of classical physics and relativity, And that would bring up a whole host of physics problems. It takes a concerted effort from the academic community, Do furtherin‐depth analysis and research. Strive forthe further discovery and perfection of physics theory.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Among the major systems of high-speed rail, the arch network relationship, wheel-rail relationship and fluid-structure coupling relationship are important links affecting the performance of high-speed rail, and also the main control factors affecting the speed limit of high-speed rail. From this perspective, the contact state and interactive relationship between pantograph and catenary are the key factors affecting the forward performance of high-speed rail. As a key component in the pantograph system, the actuator is responsible for adjusting the contact force and position between the pantograph and the contact line. The performance characteristics of the actuator, such as response speed, accuracy, stability and durability, directly affect the control performance of the whole pantograph system. In this paper, the research status of the active control technology of high-speed railway pantograph is reviewed, and the future development direction is pointed out, which provides a new idea for the development of pantograph technology.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

B lymphocyte development has two DNA recombination processes: V(D)J recombination of the immunoglobulin (Igh) gene variable region and class switching of the Igh constant regions from IgM to IgG, IgA, or IgE. V(D)J recombination is required for successful maturation of B cells from pro-B to pre-B to immature-B and then to mature B cells in the bone marrow. CSR occurs outside of the bone marrow when mature B cells migrate to peripheral lymphoid organs, such as spleen and lymph nodes. Both V(D)J recombination and CSR depend on an “open chromatin” state that makes DNA accessible to specific enzymes, recombination activating gene (RAG), and activation-induced cytidine deaminase (AID). Acetyltransferases GCN5 and PCAF possess redundant functions acetylating histone H3 lysine 9 (H3K9). Here, we generated a mouse model that lacks both GCN5 and PCAF in B cells. We found that double-deficient mice possess low levels of mature B cells in the bone marrow and peripheral organs, an accumulation of pro-B cells in bone marrow, and reduced CSR levels. We conclude that both GCN5 and PCAF are required for B cell development in vivo.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

In February 2004, the Food and Drug Administration (FDA) was the first to approve the combination of cisplatin (CDDP) and pemetrexed (PEM) as standard first-line chemotherapy for untreated, unresectable malignant pleural mesothelioma (MPM). However, after that approval, no progress was made in the standard first-line treatment of MPM for almost 15 years. Positive results from a phase 3 study (Mesothelioma Avastin Cisplatin Pemetrexed Study: MAPS) verifying the effect of bevacizumab, an anti-angiogenesis agent added to CDDP/PEM for unresectable MPM, were published in The Lancet in December 2015; however, this did not lead to approval by national drug regulatory agencies. Furthermore, no second-line treatment was established for cases refractory to CDDP/PEM. In August 2018, the Pharmaceuticals and Medical Devices Agency of Japan was the first in the world to approve monotherapy with nivolumab, an immune checkpoint inhibitor (ICI), for previously unresectable, advanced, or recurrent MPM. Following Japan, in October 2020, the FDA approved the combination of nivolumab and ipilimumab for the treatment of previously untreated, unresectable MPM. In this article, we review the transition of drug treatment for MPM, in light of the historical background, focusing on the benefits of ICIs.

Neurological involvement following COronaVIrus Disease 19 (COVID-19) is thought to have a neuroinflammatory etiology. Co-ultraPEALut (an antiinflammatory molecule) and luteolin (an antioxidant) yielded promising results as neuroinflammation antagonists. This study aimed at describing cognitive impairment in post-COVID patient treated with co-ultraPEALut. Montreal Cognitive Assessment (MoCA), Prospective-Retrospective Memory Questionnaire (PRMQ), Fatigue Severity Scale (FSS) and a subjective evaluation were administered at baseline and after 10 months. Co-ultraPEALut-treated patients were retrospectively compared with controls. 26 co-ultraPEALut-treated patients showed significant improvement in PRMQ (T0: 51.94±10.55, T1: 39.67±13.02, p

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

Most empirical work on sources of economic growth for different countries lack country-specific empirical evidence to guide policy choices in individual developing countries and previous studies of factor productivity tend to focus on the entire economy or a single sector. In this study, we use the recently developed growth accounting tools to explicitly determine the sources of economic growth at both national and sectoral levels in Zambia between 1970 and 2013. We use data from World Development Indicators and Zambia’s Central Statistical Office. On average, total factor productivity (TFP) contributes about 5.7% to economic growth. Sectoral analysis shows that agriculture contributes the least to GDP and that within each sector; factors that contribute to growth differ. Structural transformation has been slow and contributed to the observed inefficiency. We outline the implications of the observed growth and provide recommendations.

Preventing the rebound of black and odorous water bodies is critical for improving the ecological environment of water bodies. This study investigated the effect and mechanism of in-situ improvement of sediment microenvironment by nitrate in tailwater of wastewater treatment plants combined with aerobic denitrifying bacteria under low-DO regulation (TailN+CFM+LDO). On the 60th day of remediation, the dissolved oxygen and oxidation-reduction potential in the overlying water increased to 5.6 mg/L and 300 mV, respectively, the acid volatile sulfide in the sediment decreased by 70.4%, and the organic matter in the sediment was reduced by 62.7%, in which the HFOM was degraded from 105 g/kg to 56 g/kg, and the potential risk of water reverting to black and odorous conditions significantly decreased. Amplicon sequencing analysis revealed that the relative abundance of electroactive bacteria Thiobacillus and Pseudomonas with denitrification capacity was found to be significantly higher in the TailN+CFM+LDO group than in the other remediation groups. Functional prediction of 16S sequencing results indicated that both the quantity and activity of critical microbial enzymes involved in nitrification and denitrification processes could enhance in the TailN+CFM+LDO group. These results improved our understanding of the improvement of the sediment microenvironment and could thus facilitate its application.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

A multimodal detection system with complementary capabilities for efficient detection was developed for impurity detection. The system consisted of a visible light camera, a multispectral camera, image correction and registration algorithms. It can obtain spectral feature and color feature at the same time, and has higher spatial resolution than a single spectral camera. This system was applied to detect impurities in Pu ’er tea to verify its high efficiency. The spectral and color features of each pixel in the images of Pu ’er tea were obtained by this system and used for pixel classification. The experimental results show that the accuracy of Support Vector Machine (SVM) model based on combined features is 93%, which is 7% higher than that based on only spectral features. By applying median filtering algorithm and contour detection algorithm to the label matrix extracted from pixel-classified images, 8 impurities except hair were detected successfully. Moreover, taking advantage of the high resolution of visible light camera, small impurities can be clearly imaged. By comparing the segmented color image with the pixel-classified image, small impurities such as hair could be detected successfully. Finally, it is proved that the system can obtain multiple images to allow a more detailed and comprehensive understanding of the detected items, and has excellent ability to detect small impurities.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

(1) The present study investigated the effect of orally administered Limosilactobacillus fermentum HY7302 (HY7302) on the relationship between ocular tissue and the microbiome in the corneal injured dry eye mice model. (2) 0.1% benzalkonium chloride (BAC) was applied to the ocular surface for 14 days to induce corneal injury in male Balb/c mice. During the BAC treatment period, HY7302 (1 × 108 CFU/kg/day or 1 × 109 CFU/kg/day) or omega-3 positive control (200 mg/kg/day) were administered orally (n = 8/group). To examine signaling pathways affected by HY7302 treatment, the in vitro effects of HY7302 on tight junctions and the inflammatory response were investigated in a mouse colon epithelial cell line, CMT-93. (3) BAC exposure decreased tear production, induced ocular inflammation and corneal epithelial detachment, and altered gut microbiota. However, oral administration of HY7302 restored tear secretion and decreased corneal epithelial detachment in BAC-treated corneal injury mice. Further, HY7302 alleviated corneal inflammation via modulation of matrix metalloproteinase-9 (MMP-9) expression and alterations in gut microbiota composition. (4) These findings suggest that the gut–eye axis interaction between gut microbiota and eye tissue affects disease severity in corneal injury, and that alteration of the microbiota by HY7302 could improve eye health by regulating the inflammatory response.

Abstract: To obtain bovine oocytes in high quality, effects of vitamin C (VC) on in vitro maturation (IVM) of bovine oocytes and early embryo development were investigated. The results showed that: 1) The IVM medium containing 50 µg/mL VC improved the oocyte maturation rate, while no effects on the development of parthenogenetic embryos; 2) The in vitro culture (IVC) medium containing 20 µg/mL VC increased the cleavage rate of the in vitro fertilized (IVF) embryos, enhanced the mRNA levels of pluripotency gene Oct4, Sox2, Cdx2 and Nanog in the blastocysts, but no effect on the blastocyst rate; 3) Combing supplemention of 50 µg/mL in IVM medium + 20 µg/ml VC in IVC medium (VC 50/20) increased the cleavage rate of IVF embryos and enhanced the mRNA levels of Oct4, Sox2, Cdx2 and Nanog in the blastocysts; 4) Combination of VC 0/20 and VC 50/20 enhanced the expression of anti-apoptotic gene Bcl-2 and VC 50/0 weakened the expression of pro-apoptotic gene Bax, while VC 0/40 and VC 0/60 increased Bax expression and decreased the Bcl-2/Bax ratio in blastocysts. Together, VC supplementation at tuned concentration as well its combination in IVM and IVC media improves the developmental rates of bovine oocytes and embryos.

Understanding maturation stress and wood properties of poplar tension wood are critical for improving lumber yields and utilization ratio. In this study, Released Longitudinal Maturation Strains (RLMS), anatomical features, physical and mechanical properties, and nano-mechanical properties of the cell wall were analyzed at different peripheral positions and heights in nine inclined, 12-year-old poplar (Populus×euramericana ‘Zhonglin46’) trees. The correlations between RLMS and wood properties were determined. The results showed that there were mixed effects of artificial inclination on wood quality and properties. The upper sides of inclined stems had higher RLMS, proportion of G-layer, bending modulus of elasticity, and elastic modulus of cell wall but lower microfibril angle than the lower sides. At heights between 0.7 m and 2.2 m, only the double wall thickness increased with height, RLMS and other wood properties such as fiber length and basic density fluctuated or changed little with height. RLMS was a good indicator of wood properties in the tension wood area and at heights between 0.7 m and 1.5 m. The results of this study present opportunities to identify and select better quality wood in poplar trees.

Urinary tract diseases are common in cats, and often require surgical reconstruction. Here, to explore the possibility of urinary tract reconstruction in cats using in-vivo tissue architecture (iBTA), biosheets fabricated using iBTA technology were implanted into the feline bladder and the regeneration process was histologically evaluated. The biosheets were prepared by embedding molds into the dorsal subcutaneous pouches of six cats for 2 months. A section of the bladder wall was removed, and the biosheets were sutured to the excision site. After 1 and 3 months of implantation, the biosheets were harvested and evaluated histologically. Implantable biosheets were formed with a success rate of 67%. There were no major complications following implantation, including tissue rejection, severe inflammation, or infection. Urinary incontinence was also not observed. Histological evaluation revealed the bladder lumen was almost entirely covered by urothelium after 1 month, with myofibroblast infiltration into the biosheets. After 3 months, the urothelium became multilayered, and mature myocytes and nerve fibers were observed at the implantation site. In conclusion, this study showed that tissue reconstruction using iBTA can be applied to cats, and that biosheets have the potential to be useful in both the structural and functional regeneration of the feline urinary tract.

Mass transfer restrictions of scaffolds are currently hindering the development of three-dimensional (3D), clinically viable, and tissue engineered constructs. For this situation, a 3D poly(lactide-co-glycolide)/hydroxyapatite porous scaffold, which was much favorable for transfer of nutrients to and waste products from the cells in the pores, was developed in this study. The 3D scaffold had an innovative structure, including macropores with diameters of 300−450 μm for cell ingrowth and microchannels with diameters of 2−4 μm for nutrition and waste exchange. The mechanical strength in wet state was strong enough to offer the structural support. The typical structure was more beneficial for the attachment, proliferation, and differentiation of rabbit bone marrow mesenchymal stem cells (rBMSCs). The alkaline phosphatase (ALP) activity and calcium (Ca) deposition were evaluated on the differentiation of rBMSCs, and the results indicated that the microchannel structure was very favorable for differentiating rBMSCs into maturing osteoblasts. For repairing rabbit radius defects in vivo, there was rapid healing in the defects treated with the 3D porous scaffold with microchannels, where the bridging by a large bony callus was observed at 12 weeks post-surgery. Based on the results, the 3D porous scaffold with microchannels was a promising candidate for bone defect repair.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Infectivity assays are the key analytical technology for development of manufacturing processes for virus-based therapeutics. Here, we introduce a novel assay format that utilizes label-free bright field images to determine the kinetics of infection-dependent changes in cell morphology. In particular, cell rounding is directly proportional to the amount of infectious virus applied, enabling rapid determination of viral titers in relation to a standard curve. Our kinetic infectious virus titer (KIT) assay is stability-indicating and, due to its sensitive readout method, provides results within 24 hours post-infection. Compared to traditional infectivity assays, which depend on a single readout of an infection endpoint, cumulated analysis of kinetic data by a fit model results in precise results (CV &lt; 20%) based on only three wells per sample. This approach allows for a high throughput with ~400 samples processed by a single operator per week. We demonstrate the applicability of the KIT assay for VSV-GP and NDV, but it can potentially be extended to a wide range of viruses that induce morphological changes upon infection. The versatility of this assay, combined with its independence from specific instruments or software, makes it a promising solution to overcome the analytical bottleneck in infectivity assays within the pharmaceutical industry and as a routine method in academic research.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

We developed an ovarian cancer-targeted drug delivery system based on a follicle-stimulating hormone receptor (FSHR) peptide. The lipophilic chemotherapeutic drug SN38 and the photosensitizer IR820 were loaded into the phospholipid bilayer of liposomes. Near-infrared laser irradiation stimulated the generation of reactive oxygen species, causing short-term reactive molecular species and spatial-temporal restricted photodamage to the biological targets. The reactive molecular species and spatial-temporal restricted photodamage enhanced the release and uptake of chemotherapy drugs and increased the sensitivity to chemotherapy drugs in ovarian cancer cells. FSH liposomes loaded with SN38 and IR820 (SN38/IR820-Lipo@FSH) were prepared using thin-film hydration-sonication. FSH peptide binding was analyzed using 1H NMR spectrum and Maldi-Tof. The average size and zeta potential of SN38/IR820-Lipo@FSH were 105.1 ± 1.15 nm (PDI: 0.204 ± 0.03) and −27.8 ± 0.42 mV, respectively. SN38/IR820-Lipo@FSH exhibited good drug-loading properties and the in vitro release was slow. FSH significantly increased the uptake of liposomes, inhibited cell proliferation, and induced apoptosis in A2780 cells. Moreover, SN38/IR820-Lipo@FSH exhibited good tumor-targeting ability and anti-ovarian cancer activity in vivo. The SN38/IR820-Lipo@FSH exhibited specific targeting to A2780 ovarian cancer cells. The combination of chemotherapy and photodynamic treatment based on an FSH peptide-targeted delivery system may be an effective approach to treating ovarian cancer.

Objectives: The study aimed to develop a deep learning-based edge AI model deployed on electrocardiograph (ECG) devices for real-time detection of atrial fibrillation (AF)-risk during sinus rhythm (SR) using standard 10-second 12-lead electrocardiograms (ECGs). Methods: A novel approach was used to convert standard 12-lead ECGs into binary images for model input, and a lightweight convolutional neural network (CNN)-based model was trained using data collected by the Japan Agency for Medical and Research Development (AMED) between 2019 and 2022. Patients over 40 years old with digital, SR ECGs were retrospectively enrolled and divided into AF and non-AF groups. Data labeling was supervised by cardiologists. The dataset was randomly allocated into training, validation, and internal testing datasets. External testing was conducted on data collected from other hospitals.　Results: The best-trained model achieved an AUC of 0.82 and 0.80, sensitivity of 79.5% and 72.3%, specificity of 77.8% and 77.7%, precision of 78.2% and 76.4%, and overall accuracy of 78.6% and 75.0% in the internal and external testing datasets, respectively. The deployed model and app package utilized 2.5MB and 40MB of the available ROM and RAM capacity on the edge ECG device, correspondingly. Processing time for AF-risk detection was approximately 2 seconds.　Conclusion: The model maintains comparable performance and improves its suitability for deployment on resource-constrained ECG devices, thereby expanding its potential impact to a wide range of healthcare settings. Its successful deployment enables real-time AF-risk detection during SR, allowing for timely intervention to prevent AF-related serious consequences like stroke and premature death.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

Nitraria tangutorum Bobrov is a berry shrub with white flowers and red fruits, which grows in the deserts in the Tibetan Plateau, Mongolia, and western China. Its fruit N. tangutorum fruit (NTF) contains various bioactive compounds, with anti-fatigue, anti-inflammatory, and neuroprotective functions. However, the high saccharide content of NTF makes it unsuitable for diabetic patients. In this study, we fermented NTF to obtain N. tangutorum fermented juice (NTJ), and N. tangutorum fermented residue (NTR), which are suitable for diabetics to consume. We characterized the bioactive compounds in NTF, NTR, and NTJ, and found that fermentation increased the diversity of bioactive compounds, and greatly reduced sucrose, glucose, and fructose content while generating trehalose, which has the potential to manage blood glucose levels. Further, NTJ displays anti-diabetic potential due to various compounds anti-diabetic properties. This study provides a basis for further clinical research on NTJ's anti-diabetic function in humans.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

In Indonesia, types of meat are still identified manually due to increasing prices for beef and buf-falo ahead of Idul Fitri. Traders mix beef with pork to thwart the beef scam. Haar wavelet and GLCM, GLCM with angles of 0°, 45°, 90°, and 135°, as well as matrices using contrast, correlation, energy, homogeneity, and entropy, are used in feature extraction. The following are the results of meat image classification testing using k-NN, Haar wavelet, and GLCM: The k-NN algorithm shows superiority in identifying fresh (99%), frozen (99%), and rotten (96%) meat texture images with the most fantastic accuracy results in every situation. Meanwhile, GLCM routinely provides good results, especially regarding the texture image of fresh meat (183.21) and rotten meat (115.79). However, despite delivering less throughput than k-NN and GLCM, Haar wavelets are still helpful, especially when dealing with fresh meat texture images (89,96).

This study focuses on the decisions of picking, inventory, ripening, delivering, and selling mangoes in a harvesting season. Demand, supply, and prices are uncertain, and their probability density functions are fitted based on actual trading data collected from the largest spot market in Taiwan. A stochastic programming model is formulated to minimize the expected cost under the considerations of labor, storage space, shelf life, and transportation restrictions. We implement the sample-average approximation to obtain a high-quality solution of the stochastic program. The analysis compares deterministic and stochastic solutions to assess the uncertain effect on the harvest decisions. Finally, the optimal harvest schedule of each mango type is suggested based on the stochastic program solution.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Viral co-infections, where a host is infected by multiple viruses simultaneously, are common in the human population. Human viral co-infections can lead to complex interactions between viruses and the host immune system, affecting the clinical outcome and posing challenges for treatment. Understanding the types, mechanisms, impacts, and identification methods of human viral co-infections is crucial for the prevention and control of viral diseases. In this review, we first introduce the significance of studying human viral co-infections and summarize the current research progress and gaps in this field. We then classify human viral co-infections into four types based on the pathogenic properties and species of the viruses involved. Next, we discuss the molecular mechanisms of viral co-infections, focusing on virus-virus interactions, host immune responses, and clinical manifestations. We also summarize the experimental and computational methods for identifying viral co-infections, emphasizing the latest advances in high-throughput sequencing and bioinformatics approaches. Finally, we highlight the challenges and future directions in human viral co-infection research, aiming to provide new insights and strategies for the prevention, control, diagnosis, and treatment of viral diseases. This review provides a comprehensive overview of the current knowledge and future perspectives on human viral co-infections, and underscores the need for interdisciplinary collaborations to address this complex and important topic.

Background: Microscopic examination of acid-fast stained sputum smears for detecting mycobacterial acid-fast bacilli (AFB) remains the most economical and readily available method for laboratory diagnosis of tuberculosis (TB). However, this conventional approach has limitations, including low sensitivity and labor-intensive procedures. Methods: An automated microscopy system incorporating artificial intelligence (AI) and machine learning for AFB identification was evaluated. The study was conducted at an Infectious Disease Hospital in Jiangsu Province, China, utilizing an intelligent microscope system (TB-Scan, Wellgen Medical, Kaohsiung). A total of 1,000 sputum smears were included in the analysis, with the system capturing digital microscopic images and employing an image recognition model to automatically identify and classify AFB. Referee technicians provided the gold standard for discrepant results. Results: The automated system demonstrated an overall accuracy of 95.00% (950/1,000), sensitivity of 91.24% (177/194), and specificity of 95.91% (773/806). Notably, the system identified 21 smears as positive that were previously reported as negative, with referee technicians confirming 17 of these as true positive and retracting the test results accordingly. Recalculating the performance, the accuracy increased to 96.70% (967/1,000), sensitivity to 91.94% (194/211), and specificity to 97.97% (773/789), with a false negative rate of 8.06% (17/211) and a false positive rate of 2.03% (16/789). Conclusions: The incorporation of AI and machine learning into an automated microscopy system demonstrated the potential to enhance the sensitivity and efficiency of AFB detection in sputum smears compared to conventional manual microscopy. This approach holds promise for widespread application in TB diagnostics and potentially other fields requiring labor-intensive microscopic examination.

Ensuring access to water, sanitation, and hygiene (WASH) facilities, coupled with behavior change education in schools, is fundamental for fostering a conducive learning environment and promoting principles of inclusion, dignity, and equality. This study focuses on 12 primary schools in Anápolis, Brazil, encompassing 4,394 students and 248 teachers. WASH assessments were conducted through a questionnaire, observation of water and sanitation facilities and structures, and microbiological analysis. Over the period 2018 to 2020, the proportion of schools with safely managed drinking water surged from 42% to 92%. However, sanitation conditions in the schools were categorized as a basic level, with hygiene services rated as limited in 92% of the schools due to the absence of soap. While this study reveals that Anápolis schools generally align with WASH guidelines for basic/advanced drinking water services, there is a crucial need for enhancements in both hardware and software facilities to address sanitation and hygiene challenges.

Multiple Myeloma (MM) is one of the incurable types of cancer in plasma cells. While immense progress has been made in the treatment of this malignancy, a large percentage of patients were unable to adapt to such therapy. Additionally, these therapies might be associated with significant diseases and are not always tolerated well in all patients. Since cancer in plasma cells has no cure, patients develop resistance to treatments, resulting in R/R MM. BCMA is primarily produced on mature B cells. Its up-regulation and activation are associated with multiple myeloma in both murine and human models, indicating that this might be an effective therapeutic target for this type of malignancy. Additionally, BCMA's predictive value, association with effective clinical trials, and capacity to be utilized in previously difficult to observe patient populations, imply that it might be used as a biomarker for multiple myeloma. Numerous kinds of BCMA-targeting medicines have demonstrated antimyeloma efficacy in individuals with refractory/relapsed MM, including CAR T-cell treatments, ADCs, bispecific antibody constructs. Among these medications, CART cell-mediated BCMA therapy has shown significant outcomes in multiple myeloma clinical trials. This review article outlines CAR T cell mediated BCMA medicines have the efficiency to change the therapeutic pattern for multiple myeloma significantly.

Underwater image often exhibit detail blurring and color distortion due to light scattering, impurities, and other influences, obscuring essential textures and details. This presents a challenge for existing super-resolution techniques in identifying and extracting effective features, making high-quality reconstruction difficult. This research aims to innovate underwater image super-resolution technology to tackle this challenge. Initially, an underwater image degradation model was created by integrating random subsampling, Gaussian blur, mixed noise, and suspended particle simulation to generate a highly realistic synthetic dataset, thereby training the network to adapt to various degradation factors. Subsequently, to enhance the network's capability to extract key features, improvements were made based on the symmetrically structured Blind Super-Resolution Generative Adversarial Network (BSRGAN) model architecture. An attention mechanism based on energy functions was introduced within the generator to assess the importance of each pixel, and a weighted fusion strategy of adversarial loss, reconstruction loss, and perceptual loss was utilized to improve the quality of image reconstruction. Experimental results demonstrate that the proposed method achieved significant improvements in Peak Signal-to-Noise Ratio (PSNR) and Underwater Image Quality Measure (UIQM) by 0.85 dB and 0.19, respectively, significantly enhancing the visual perception quality and indicating its feasibility in super-resolution applications.

Despite increased protection globally, climate change and other anthropogenic factors have caused a significant decline in seagrass cover. Identifying the specific causes of this decline is paramount if they are to be addressed. Therefore, we identified the causes of long-term change in seagrass/submerged aquatic vegetation (SAV) percentage cover and extent in the Bluefields Bay Special Fish Conservation Area (BBSFCA), a marine protected area on Jamaica’s southern coast. We used two random forest regression (RFr) models that included 2013 hydroacoustic survey SAV percentage cover data (dependent variable), and auxiliary data, reflectance data from level 2 processed 2013 Landsat 7 and 8 images and image band texture statistics maps (mean and variance) as predictors to generate 24 SAV percentage cover maps for the period 1984 – 2021 (37 years) using data from Landsat 4-5, 7 and 8 images., from which benthic features maps (SAV present, absent and coral reef) were created. Rainfall and map data were used to determine if SAV extent/area (km2) and average percentage cover and annual rainfall changed significantly over time and to evaluate the influence of rainfall. Rainfall impact on the overall spatial patterns of SAV loss, gain, and percentage cover change was assessed using a pixel-based regression. Finally, the most important spatial pattern predictors (two rainfall proxies (distance and direction from river mouth), benthic topography, depth, and hurricane exposure (a measure of hurricane disturbance)) of SAV loss, gain, and percentage cover change during 23 successive 1-to-4-year periods were identified using spatial Bayesian INLA generalized linear mixed models. SAV area/extent was largely stable with &gt; 70% mean percentage cover for multiple years. However, Hurricane Ivan (in 2004) caused a significant decline in SAV area/extent (by 1.62 km2, or a 13%) during 2002 – 2006 and a second hurricane (Dean) in 2007 delayed recovery until 2015. Additionally, rainfall declined significantly by &gt;1000 mm since 1901, and mean monthly rainfall positively influenced SAV percentage cover change. The pixel-based regression highlighted areas where mean monthly rainfall had a positive overall effect on SAV cover percentage change (across the entire bay) and gain (closer to the mouth of a river). The most frequently selected important spatial pattern predictors were the two rainfall proxies (areas closer to the river mouth were more likely to experience SAV loss and gain) and depth, with shallow areas generally having a higher probability of SAV loss and gain. Three hurricanes had significant but different impacts depending on their distance from the southern coastline. Hurricane Gilbert, which made landfall in 1988, resulted in higher SAV percentage cover loss in 1987 - 1988. Benthic locations with a northwestern/northern facing aspect (the predominant direction of Ivan’s leading edge wind bands) experienced higher SAV losses during 2002 – 2006. Although some locations impacted by Ivan and not by Dean recovered during 2006 – 2008, exposure to Ivan explained percentage cover loss during 2006 – 2008 and average exposure to (the cumulative impact of) Ivan and Dean (both with tracks close to the southern coastline) explained SAV loss during 2013 – 2015. Therefore, despite historic lows in annual rainfall, overall, higher rainfall was beneficial, multiple hurricanes impacted the site, and despite two hurricanes in three years SAV recovered within a decade. Hurricanes and a further reduction in rainfall may pose a serious threat to SAV persistence in the future.

Since the 1970s, the usefulness of nailfold capillaroscopy (NFC) in the diagnosis of rheumatological disorders such as systemic sclerosis has been well known, and further studies also showed that NFC can detect non-rheumatic diseases such as diabetes, glaucoma, dermatitis, Alzheimer disease, and so on. In the past decade, the morphological changes in the nailfold capillary have been also reported in the unhealthy lifestyle habits such as smoking, inappropriate diets, sleep shortage, and even psychological stress which presents slow blood flow. Therefore, study in the relationships between the morphology of nailfold capillaries and lifestyle habits has high potential to understand the unhealthy state, or even predict the pre-disease condition. So, simple, inexpensive, and non-invasive methods such as NFC are constantly needed for routine health checkups. Thus, we undertook a systematic search in PubMed database, and summarized the studies reporting the assessment of morphological NFC in order to undertake a comprehensive review on the usefulness of NFC not only in clinical diagnosis, but also in unhealthy dietary lifestyle improvements. Here in this review paper, we finally summarized the dietary and lifestyle health promotion strategy judging from NFC- and the other relating-measurement from the viewpoint of healthy microvascular blood flow and endothelial function.

Background: Autism spectrum disorder (ASD) is a persistent neurodevelopment disorder frequently co-occurring with Attention-Deficit/Hyperactivity Disorder (ADHD) and behavior-related disorders. While behavioral therapy is the first-line option to manage ASD core symptoms, pharmacological therapy is sometimes needed to treat acute problems, such as agitation and aggressive behaviors. Recent guidelines recommend neuroleptics to reduce psychomotor agitation in people with ASD. However, since children with ASD are often drug-resistant, alternative treatments are often justified. Reports from literature showed that intra-venous valproate (IV-VPA) can be effective in reducing agitation in psychiatric patients, with lower frequency of adverse events compared to convention-al treatments. However, since findings are occasionally inconsistent, IV-VPA is not an approved option in clinical psychiatry. We aim at improving the knowledge on the IV-VPA treatment option in emergency psychiatry in the pediatric age. Methods: We report the case of a 11-year-old boy suffering from a complex neurodevelopmental condition, who experienced a psychotic episode with severe aggressive and disruptive behaviors, successfully treated with IV-VPA. Besides, we conducted an up-dated literature review on this topic. Conclusion: In our case, first-line therapies proved to be ineffective. On the contrary, IV-VPA led to a safe and prompt clinical success, in line with other reports. Based on our literature review, IV-VPA can be highly effective and can reduce the risk of adverse events that frequently occur with the use of high-dose standard medications in emergency psychiatry.

Rare diseases are characterized by a wide diversity of signs and symptoms and vary not only from disease to disease, but also from person to person, and living with a disease leads patients to peculiar experiences and treatments, without limits of time and space, as they extend to various environments and relationships of their lives. The objective of this study is the theoretical interaction between Value Co-creation (VC) and the Stakeholder Theory (ST) with the Shared Decision Making (SDM) health care theory. It is configured as a multiparadigmatic proposal by enabling the analysis of multiple perspectives of different stakeholders in health care. Thus, Co-created Decision Making (CDM) emerges in a logic dominated by service, with emphasis on intangible aspects and the interactivity of the relationships. It goes beyond the clinical office and the doctor-patient relationships, as studied in SDM, extending to all environments and interactions that add value to the patient's treatment. It was concluded that the essence of this new theory proposed here is neither in patient-centered care nor in patient self-care, but in co-created relationships with and between stakeholders in both directions, including non-health care environments that are important to the patient, such as relationships with friends, family, other patients with the same disease, social media, public policies, and the practice of pleasurable activities.

Background: Health insurance (HI) run by government is providing health care service to large population. Due to poor accountability, participation and sustainability, cooperative health insurance is becoming more popular and effective in low and middle income and some high-income countries too. In Nepal, there are public and cooperative HI is in practice. The aim of this study is to compare the effectiveness of public (government) and cooperative HI in relation to benefit packages, population coverage, inclusiveness, health care utilization, and promptness for treatment in these two health insurance models in Nepal. Method: This is an institution based concurrent mixed study consists of qualitative and quantitative variables from public and cooperative groups. We included all public HI operated by government hospitals and cooperatives groups those purchased hospital service in contract. Two separate study tools were applied to access the effectiveness of insurance models. The key questions were asked for the representatives of government and private health insurance. The numeric information consisted of in quantitative data and subjective response was included in qualitative approach. Descriptive statistics and Mean Whitney U test was applied in numeric data and qualitative information were analyzed by inductive approach Results: The study revealed that new enrolment was not increased, health care utilization rate was increased and the benefit package was almost same in both groups. The overall inclusiveness was higher for the government HI, but enrolment from the religious minority, proportion of negotiated amount during treatment were significantly higher (p<0.05). During illness, the response time to reach hospital was significantly faster in cooperative health insurance than government health insurance. Qualitative findings showed that level of participation, accountability, transparency and recording system was better in cooperative health insurance than public. Conclusion: Cooperative HI could be more sustainable and accountable to the community for all; low, middle and high-income countries.

Background: The most common form of vascular access for hemodialysis is a native arteriovenous fistula, which connects site of the artery to the end of the vein. The maturation process of the fistula plays a crucial role in the establishment of a functional vascular access. Radial artery stenosis is among others a potential cause of maturation failure. In these cases, improving the fistula's blood flow may be difficult, as traditional surgical reanastomosis and endovascular intervention frequently fail. Radial artery deviation and reimplantation (RADAR) is a novel, effective technique for creating primary fistulas with a high patency rate. The main disadvantage of this procedure is the ligation of the radial artery and the subsequent known consequences. Methods: In order to accelerate maturation, we used RADAR as a secondary fistula in three patients with radial artery stenosis and maturation failure. In all patients after surgery we observed significant increase in fistula blood flow. Two patients used fistula for hemodialysis after surgery. We describe the image diagnosis, procedure, and benefits of this method based on a single case. Conclusion: The RADAR technique may be successfully used as a secondary access in patients with maturation failure, due to RA stenosis to accelerate fistula maturation.

Bone growth plate abnormalities and skull shape defects are seen in hypophosphatasia, a heritable disorder in humans that occurs due to deficiency of Tissue Nonspecific Alkaline Phosphatase (TNAP, Alpl) enzyme activity. Abnormal development of the cranial base growth plates (synchondroses) and abnormal skull shapes have also been demonstrated in global TNAP-/- mice. To distinguish local vs. systemic effects of TNAP on skull development, we utilized P0-Cre to knockout TNAP only in cranial neural crest derived tissues using TNAP flox mice. Here we show that TNAP deficiency in cranial neural crest leads to leads to skull shape defects and deficient growth of the intersphenoid synchondrosis (ISS). ISS chondrocyte abnormalities included increased proliferation in resting and proliferative zones with decreased apoptosis in hypertrophic zones. ColX expression is increased, indicative of premature differentiation in the absence of TNAP. Sox9 expression is increased in both resting and prehypertrophic zones of mutant mice. Expression of PTHrP and IHH were also increased. Finally, cranial base organ culture revealed that inorganic phosphate (Pi) and pyrophosphate (PPi) have specific effects on cell signaling and phenotype changes in the ISS. Together, these results demonstrate that TNAP expression in growth plate chondrocytes is essential for normal development, and that the mechanism likely involves Sox9, PTHrP, IHH and PPi.

Bacteria develop various defense mechanisms against stresses, including the bacteriophage infection. The giant phiKZ phage infection induced the appearance of a pseudo-nucleus inside the bacterial cytoplasm. Here, we used FISH, electron tomography and analytical electron microscopy to study the morphology of this unique nucleus-like shell and to demonstrate the distribution of phiKZ and bacterial DNA in infected P. aeruginosa cells. The maturation of the pseudo-nucleus was traced in short intervals for 40 min after infection. This study was accompanied by the identification of phiKZ and bacterial DNA by real-time RCR. We demonstrated that phage DNA that isolated from the cytoplasm during all infection stages were compacted within the pseudo-nucleus in a specific structure. Bacterial DNA was diminished in the course of infection, but did not completely degrade until at least 40 min after phage application. The content of the total phage DNA, on the other hand, increased. EDX analysis confirmed these results and revealed that, during the infection, Sulfur content in the bacterial cytoplasm increased, which suggests the increase of DNA-binding Met-reach proteins synthesis, which could protect bacterial DNA from stress.

Dendritic cells (DCs) are the most specialized antigen-presenting cells and lymph nodes (LNs) play an important role in the DC-mediated T-cell response. We evaluated the infiltration of CD1a-positive DCs (CD1a-DCs) i.e. immature DCs, and S100-positive dendritic cells (S100-DCs), a mixture of immature- and mature DCs, in 73 cases of laryngeal cancer and its regional LNs. Among them, 31 patients underwent radiotherapy (RT) or chemoradiotherapy (CRT) prior to surgery. No significant difference was found for CD1a-DC infiltration in the primary tumor, metastatic LNs and non-metastatic LNs, while S100-DCs were significantly fewer in number in the primary tumor and metastatic LNs compared to non-metastatic LNs. Cases which showed a high infiltration of S100-DCs in metastatic LNs appeared to show a favorable prognosis although statistical significance was not reached. In the RT/CRT group, infiltration of CD1a-DCs and S100-DCs were fewer in the primary tumor and metastatic LNs compared to the treatment naive group. Conversely, the RT/CRT group showed higher CD1a-DCs and S100-DCs numbers in non-metastatic LNs compared to the treatment naïve group. Thus, DC maturation in metastatic LNs plays an important role in tumor immunity in laryngeal cancer, and infiltration of DCs into the primary tumor and metastatic LNs is impaired by RT/CRT.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

Androgens are key for pubertal development of the mammalian testis, a phenomenon tightly linked to Sertoli cell maturation. In this review, we discuss how androgen signalling affects Sertoli cell function and morphology by concomitantly inhibiting some processes and promoting others that contribute jointly to the completion of spermatogenesis. We focus on the molecular mechanisms that underlie AMH inhibition by androgens at puberty, as well as on the role androgens have on Sertoli cell tight junction formation and maintenance and, consequently, on its effect on proper germ cell differentiation and meiotic onset during spermatogenesis.

This research explores the behaviors of Generation Z consumers in China, particularly focusing on their interaction with companies through social media for the joint creation of value. Adopting a qualitative methodology, the research initially constructs a scale for assessing co-creation of value on social media platforms. Subsequently, it delves into the motivational aspects of users' engagement in these co-creative activities. The study unveils a range of utilitarian and hedonic motivations that drive Generation Z's value co-creation actions on social media. Insights derived from the findings offer both theoretical and practical implications for the field.

This paper proposes a lightweight joint with bamboo culm cross connection, which is constructed by screwing one side of the screw into the other side of the wooden plug, its simple construction makes it easy to manufacture and cost-effective. This form connects adjacent bamboo culms to form corner joints, and bolt connects adjacent bamboo culm frames to form edge joints, to explore the mechanical properties of the combination joints formed by corner joints and edge joints, by combining experiments and numerical simulations, the method discovered and explained the relationship and mechanism between the number and position of bolts and the stiffness of edge joints. A calculation model for frame-unit bamboo culm members considering semi-stiffness of joints is proposed, and the conversion equations between linear stiffness of corner and edge joint and their rotational stiffnesses are derived. By establishing the series and parallel relationship between the corner and edge joints in the assembled members, a generalized relational equation between the total stiffness of the assembled joint and the stiffness of the corner and edge joints is derived. A numerical simulation method for frame-unit bamboo culm members with semi-rigid joints is proposed, which can obtain the stiffness calculation formula of edge joints and the average rotational stiffness value of semi-rigid corner joints. A finite element analysis method based on semi-rigid joints is proposed for frame-unit bamboo culm members, and the internal force sketches and calculation methods for bamboo culms and joints are presented, which can be used for the internal force analysis and design of frame-unit bamboo culm lattice structures.

Electric torque wrenches play a crucial role in the assembly of high-strength bolts. This study focuses on three assembly processes for high-strength bolts and introduces a statistical analysis method to assess the quality of the bolt assembly. To enhance the performance, a novel, fully digital, Internet of Things (IoT) electric torque wrench is designed, incorporating a smart meter chip. This wrench achieves integration between the current sensor control method and the torque sensor control method using a simplified hardware circuit, ensuring high precision and stability. Additionally, this study employs the AC voltage self-stabilization method and Savitzky–Golay filtering method to enhance the accuracy and robustness of the wrench. Simulation experiments using Simulink and Matlab validate the effectiveness of these two methods. Furthermore, a cloud platform is utilized to enable rapid IoT access for the wrench, facilitating seamless connectivity and data transmission.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

FeIFeI Fe2(S2C3H6)(CO)6(µ-CO) (1a-CO) and its FeIFeII cationic species (2a+-CO) are the simplest model of the CO-inhibited [FeFe] hydrogenase active site, which is known to undergo CO photolysis within a temperature- dependent process whose products and mechanism are still a matter of debate. Using Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TDDFT) computations, the ground state and low-lying excited state potential energy surfaces (PESs) of 1a-CO and 2a+-CO have been explored aimed at elucidating the dynamics of the CO photolysis yielding Fe2(S2C3H6)(CO)6 (1a) and Fe2(S2C3H6)(CO)6+ (2a+), two simple models of the catalytic site of the enzyme. Two main results came out from these investigations. First, a-CO and 2a+-CO are both bound with respect to any CO dissociation with lowest free energy barriers around 10 kcal mol-1, suggesting that at least 2a+-CO might be synthetized. Second, focusing on the cationic form, we found at least two clear excited state channels along the PESs of 2a+-CO that are unbound with respect to equatorial CO dissociation.

Co-inhibitory receptors (Co-IRs) are essential in controlling the progression of immunopathology in rheumatoid arthritis (RA) by limiting T cell activation. The objective of this investigation was to determine the phenotypic expression of Co-IRs T cells and to assess the levels of serum soluble PD-1, PDL-2, and Tim3 in Taiwanese RA patients. Co-IRs T cells were immunophenotyped employing multicolor flow cytometry, and ELISA was utilized for measuring soluble PD-1, PDL-2, and Tim3. Correlations have been detected across the percentage of T cells expressing Co-IRs (MFI) and different indicators in the blood, including ESR, high sensitivity CRP (hsCRP), 28 joint disease activity scores (DAS28), and soluble PD-1/PDL-2/Tim3. In RA patients, we recognized elevated levels of PD-1 (CD279), CTLA-4, and TIGIT on CD4+ T cells; TIGIT, HLA-DR, TIM3, and LAG3 on CD8+ T cells; and CD8+CD279+TIM3+, CD8+HLA-DR+CD38+ T cells. The following tests proved to be correlated with hsCRP: CD4/CD279 MFI, CD4/CD279%, CD4/TIM3%, CD8/TIM3%, CD8/TIM3 MFI, CD8/LAG3%, and CD8+HLA-DR+CD38+%. CD8/LAG3 and CD8/TIM3 MFIs are linked to ESR. DAS28-ESR and DAS28-CRP exhibited relationships with CD4/CD127 MFI, CD8/CD279%, and CD8/CD127 MFI, respectively. CD4+CD279+TIM3+% was correlated with DAS28-ESR (p=0.0084, N=46), DAS28-CRP (p=0.007, N=47), and hsCRP (p=0.002, N=56), respectively. In the serum of patients with RA, levels of soluble PD-1, PDL-2, and Tim3 were extremely elevated. CD4+ TIM3+% (p=0.0089, N=46) and CD8+ TIM3+% (p=0.0305, N=46) were correlated with sTIM3 levels; sPD1 levels were correlated with CD4+CD279+% (p<0.0001, N=31) and CD3+CD279+% (p=0.0084, N=30). Co-IRs expressions on CD4+ and CD8+ T cells, as well as soluble PD-1, PDL-2, and Tim3 levels, could function as indicators of disease activity and potentially play crucial roles in the pathogenesis of RA, in accordance to our findings.

Carbapenem antibiotics are the drug of choice for treating multidrug-resistant bacterial infections. Metallo-beta-lactamases (MBLs) are carbapenemase capable of hydrolyzing nearly all therapeutically available beta-lactam antibiotics. Consequently, a need to assess the frequency and phenotypic resistance phenomena of two MBL genes in diarrheal and urinary tract infections (UTIs). Samples were collected through a cross-sectional study, with MBLs genes detected via PCR. Two hundred twenty eight diarrheal bacteria were isolated from 240 samples. The most predominant pathogens were Escherichia coli (32%) and Klebsiella spp. (7%). Phenotypic resistance to amoxicillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 50.4%, 65.6%, 66.8%, 80.5%, 54.4%, 41.6%, 25.7%, 41.2%, 37.2%, and 42.9%, respectively.  Total 142 UTI pathogens were obtained from 150 urine samples, with Klebsiella spp. (39%) and Escherichia coli (24%) are the major pathogens. Phenotypic resistance to amoxycillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 93.7%, 75.0%, 91.5%, 93.7%, 88.0%, 72.5%, 13.6%, 44.4%, 71.1%, and 43%, respectively.  Twenty four diarrheal isolates carried either blaNDM-1 or blaVIM genes; the overall MBL gene prevalence was 10.5%. Thirty six UTI pathogens carried either blaNDM-1 or blaVIM genes (25.4%). Seven isolates carried both blaNDM-1 and blaVIM genes.  MBL genes exhibited a strong association with phenotypic carbapenem and other beta-lactam antibiotic resistance. Resistance to carbapenems requires active surveillance and stewardship.

Objective: The study aimed to characterize the changing landscape of circulating SARS-CoV-2 lineages in the local community of Hong Kong throughout 2022. We examined how adjustments to quarantine arrangements influenced the transmission pattern of Omicron variants in a city with relatively rigorous social distancing measures at that time. Methods: In 2022, a total of 4,684 local SARS-CoV-2 genomes were sequenced using the Oxford Nanopore GridION sequencer. SARS-CoV-2 consensus genomes were generated by MAFFT, and the maximum likelihood phylogeny of these genomes were determined using IQ-TREE. The dynamic changes in lineages were depicted in a time tree created by Nextstrain. Statistical analysis was conducted to assess the correlation between changes in the number of lineages and adjustments to quarantine arrangements. Results: By the end of 2022, a total of 83 SARS-CoV-2 lineages were identified in the community. The increase in the number of new lineages was significantly associated with the relaxation of quarantine arrangements (One-way ANOVA, F(5,47)=18.233, p&lt;0.001)). Over time, Omicron BA.5 sub-lineages replaced BA.2.2 and became the predominant Omicron variants in Hong Kong. The influx of new lineages reshaped the dynamics of Omicron variants in the community without fluctuating the death rate and hospitalization rate (One-way ANOVA, F(5,47)=2.037, p=0.091). Conclusion: The study revealed that even with an extended mandatory quarantine period for incoming travelers, it may not be feasible to completely prevent the introduction and subsequent community spread of highly contagious Omicron variants. Ongoing molecular surveillance of COVID-19 remains essential to monitor the emergence of new recombinant variants.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

The aim of this study is to solve the problems of complicated pretreatment and high analytical cost in the detection technology of trace drug toxicants in municipal wastewater. A high-performance magnetic sorbent was synthesized for enrichment of trace drug substances in wastewater to develop magnetic solid-phase extraction pretreatment combined with the acoustic ejection mass spectrometry (AEMS) analytical methods for the molecules in wastewater drug toxicants. The magnetic nanospheres was successfully prepared by magnetic nanoparticles modified with divinylbenzene and vinyl pyrrolidone.The results showed that the linear dynamic range of 17 drugs was 1-500 ng/L, the recovery was 43%-105%, the matrix effect was more than 67%, the limit of quantitative detection was 1-2 ng/L, and the detection time of each sample was 2.98s. It can be seen that the developed magnetic solid-phase extraction (MSPE) method is a good solution to the problem of complicated pre-treatment and analytical cost in the detection of drugs in wastewater. The developed magnetic material and acoustic excitation coupled mass spectrometry analysis method can realize the low-cost, efficient enrichment and fast analysis of different kinds of drug molecules in urban sewage.

The segmentation of abnormal regions is vital in smart manufacturing. However, the existing segmentation system for detecting sauce-packet leakage on intelligent sensors encounters an issue of imaging blurring caused by uneven illumination. This issue adversely affects segmentation performance, thereby impeding the rapid production of industrial assembly lines. To alleviate this issue, we propose the two-stage Illumination-aware Sauce-packet Leakage Segmentation (ISLS) method for intelligent sensors. The ISLS comprises two main stages: Illumination-aware region enhancement and leakage region segmentation. In the first stage, YOLO-Fastestv2 is employed to capture the Region of Interest (ROI), which reduces redundancy computations. Additionally, we propose an image enhancement to relieve the impact of uneven illumination, enhancing the texture details of ROI. In the second stage, we propose a novel feature extraction network. Specifically, we propose the Multi-scale Feature Fusion Module (MFFM) and the Sequential Self-Attention Mechanism (SSAM) to capture discriminative representations of leakage. The multi-level features are fused by MFFM with a small number of parameters, which capture leakage semantics at different scales. The SSAM realizes the enhancement of valid features and the suppression of invalid features by adaptive weighting of spatial and channel dimensions. Furthermore, we generated a self-built dataset of sauce-packets, including 606 images with various leakage areas. Comprehensive experiments demonstrate that our ISLS method shows better results than several state-of-the-art methods, with additional performance analyses deployed on intelligent sensors to affirm the effectiveness of our proposed method. Our code is available at https://github.com/LSJ5106/SauceDetect.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Silybin is a natural compound extensively studied for its hepatoprotective, neuroprotective and anti-cancer properties. Envisioning the enhancement of silybin potential by suitable modifications in its chemical structure, here, a series of new 7-O alkyl silybins derivatives were synthesized by Mitsunobu reaction starting from the silybins and tyrosol-based phenols, such as tyrosol (TYR, 3), 3-methoxytyrosol (MTYR, 4) and 3-hydroxytyrosol (HTYR, 5). This research sought to explore the antioxidant and anticancer properties of new eighteen derivatives and their mechanisms. In particular, the antioxidant properties of new derivatives outlined by DPPH assay, showed a very pronounced activity depending on the tyrosyl moiety (HTYR&gt;MTYR&gt;&gt;TYR). A significant contribution of the HTYR moiety was observed for silybins and 2,3-dehydro-silybin based derivatives. According to the very potent antioxidant activity, 2,3-dehydro-silybin derivatives 15ab, 15a and 15b exerted the most potent anticancer activity in human prostate cancer PC-3 cells. Furthermore, flow cytometric analysis for cell cycle and apoptosis revealed that 15ab, 15a and 15b induce strong G1 phase arrest and increase late apoptotic population in PC-3 cells. Additionally, western blotting for apoptotic marker cleaved caspase-3 confirmed apoptosis induction by these silybin derivatives in PC-3 cells. These findings hold significant importance in the investigation of anticancer properties of silybin derivatives and strongly encourage swift investigation in pre-clinical models and clinical trials.

The lengthy maturation period is the key cause of the reduced hot pepper market value. An experiment was performed to assess the effects of R/B/W light qualities on reducing the maturation period. The maturation period was shortened by 16 days under 4R:1B:5W compared to the control. The appearance of the first flower is a limiting factor affecting the maturation period. It exhibited a dark purple color and an abnormal petal under 4R:1B:5W compared to the control, which was associated with increased contents of flavonoids, total organic acids, and phenolics and decreased total amino acid and carbohydrate contents. Plant hormone, flavonoid, ABC transporters, key metabolites (such as amino acid, carbohydrate, organic acid) was associated with first flower development. Ethylene response factors (ERFs) mediated by light, especially ERF021, were identified as potential hub regulators during the development of the first flower due to their involvement in all the associated metabolic pathways.

Spermatogenesis is a complex, tightly regulated biological process crucial for male fertility in mammals. MicroRNAs (miRNAs) and messenger RNAs (mRNAs) play essential functions in regulating gene expression during spermatogenesis, and their specific roles in Holstein bull testicular development remain unclear. The study analyzed testicular tissues from young and mature Holstein bulls, unveiling the post-sexual maturation transcriptome landscape with a focus on spermatogenesis-associated miRNAs and mRNA profiles. The cDNA libraries from the testicular tissues of three young Holstein bulls (X1, X2, and X3; group YB) and three mature Holstein bulls (D5, D6, and D7; group AB) were established for RNA-sequencing analysis using Illumina high-throughput sequencing technology, followed by bioinformatics analysis. A total of 1114 miRNAs were identified in the X vs. D groups: 683 known miRNAs and 431 novel miRNAs. Notably, 221 known miRNAs exhibit differential expression between the X and D groups, with 118 up-regulated and 103 down-regulated genes. Moreover, a total of 237 previously unidentified novel miRNAs were also observed to exhibit differential expression between X and D, with 77 up-regulated and 160 down-regulated miRNA genes. These miRNA genes were linked to Gene Ontology (GO) terms and Kyoto Encyclopedia of Genes and Genomes (KEGG) pathways related to male reproduction and spermatogenesis. The DE analysis of miRNA genes identified the top five up-regulated miRNAs (bta-miR-127, bta-miR-495, bta-miR-493, bta-miR-432, and bta-miR-3956) and down-regulated miRNAs (bta-miR-34c, bta-miR-34b, bta-miR-449a, bta-miR-449b, and 23_28233-5p (hsa-miR-6774-3p)) between the young bull and adult bull groups. The miRNA-mRNA network analysis also identified 17_16057-5p, X_45311-3p (cpo-miR-12072-3p), bta-miR-34c, bta-miR-375, 17_15431-5p (eca-miR-8912), 10_2547-3p (isc-miR-5313), bta-miR-449b, and mRNA genes such as BCL2L11, ADAMTSI1, MED1, and PRDM1; these genes were associated with reproductive system development. The mRNA genes (STRB and BCL2L11) and miRNA genes (bta-miR-134, bta-let-7e, bta-miR-181b, and bta-miR-214) were also found to have a significant correlation with the spermatogenic process. Thus, the comprehensive analysis of miRNA and mRNA enhances our knowledge of the regulatory networks involved in testicular development and identifies potential targets for further investigation and manipulation to improve cattle reproductive efficiency and genetic selection.

During the past two decades there has been a major shift in the choice of agents to treat multiple myeloma, whether newly diagnosed or in the relapsed/refractory stage. The introduction of new drug classes, such as proteasome inhibitors, immunomodulators, and anti-CD38 and anti-SLAMF7 monoclonal antibodies, coupled with autologous stem cell transplantation, have approximately doubled the disease’s five-year survival rate. However, this positive news is tempered by the realization that these measures are not curative and patients eventually relapse and/or become resistant to the drug’s effects. Thus, there is a need to discover newer myeloma-driving molecular markers and develop innovative drugs designed to precisely regulate the actions of such putative targets. B cell maturation antigen (BCMA), which is found almost exclusively on the surfaces of malignant plasma cells to the exclusion of other cell types, including their normal counterparts, has emerged as a specific target of interest in this regard. Immunotherapeutic agents have been at the forefront of research designed to block BCMA activity. These agents encompass monoclonal antibodies, such as the drug conjugate belantamab mafodotin; bispecific T-cell engager strategies exemplified by AMG 420; and chimeric antigen receptor (CAR) T-cell therapeutics that include idecabtagene vicleucel (bb2121) and JNJ-68284528.

Impact in the form of innovation and commercialisation is an essential component of publicly funded research projects. PHUSICOS, an H2020 Innovation Action project, aims at demonstrating the use of nature-based solutions for mitigating hydrometeorological hazards in rural and mountainous areas. The work program is built around key innovation actions, and each WP leader specifically responsible for nurturing innovation processes, maintaining market focus and ensuring relevance for the intended recipients of the project results. Key success criteria for PHUSICOS include up-scaling and mainstreaming of NBS to reach broader market access. An innovation strategy and supporting tools for implementing this within PHUSICS has been developed and key concepts forming the basis for this strategy are presented in this research note.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

Articular cartilage lacks intrinsic regenerative capabilities, and the current treatments fail to regenerate damaged tissue and lead only to temporary pain relief. These limitations have prompted the development of tissue engineering approaches, including 3D culture systems. Thanks to their regenerative properties and capacity to recapitulate embryonic processes, spheroids obtained from mesenchymal stromal cells are increasingly studied as building blocks to obtain functional tissues. The aim of this study was to investigate the capacity of adipose stromal cells to assemble in spheroids and differentiate toward chondrogenic lineage from the perspective of cartilage repair. Spheroids were generated by two different methods (3D chips vs Ultra-Low Attachment plates), differentiated toward chondrogenic lineage, and their properties were investigated by: molecular biology analyses, biophysical measurement of mass density, weight, and size of spheroids, and confocal imaging. Overall, spheroids showed the ability to differentiate by expressing specific cartilaginous markers that correlate with their mass density, defining a critical point at which they start to mature. Considering the spheroid generation method, this pilot study suggested that spheroids obtained with chips are a promising tool for the generation of cartilage organoids that could be used for preclinical/clinical approaches, including the realization of personalized therapy.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

This study proposed to use wearable EEG to study the impact of vipassana mindfulness practice on beginner's physiological and neurological responses. Mindfulness meditation has been shown to have numerous benefits, including stress reduction, improved attention and cognitive function, and enhanced emotional regulation. The roots of mindfulness meditation in Buddhism emphasize cultivating present-moment awareness and insight. However, the neural mechanisms together with physiological mechanism and their interaction underlying these benefits remain poorly understood. Method: One middle age man (50 years old) participated in this longitudinal study using wearable EEG to investigate the neurophysiological change during a one-month consecutive vipassana mindfulness practice. Both EEG and heart rate responses were recorded each time, before (5 minutes), during (20 minutes), and after (5 minutes) meditation sessions. The EEG and HR data were analyzed by Matlab and EEGlab to examine changes in brainwave activity and heart rate. Results: alpha peak frequency (APF) is significantly lower after mindfulness meditation, as shown by comparison of APF before mindfulness (pre-5) and during mindfulness practice (med-20), and comparison between APF of pre-5 and after mindfulness practice (post-5). The same is with the beta peak power. While for theta peak frequency, it is significant lower during mindfulness meditation (med-20), when comparing to either pre-5 or post-5. See figure 1a. However, peak power index is not so sensitive, and it is more obvious in theta wave band. That is, the theta power peak is significantly lower after meditation, as can be observed in comparison between pre-5 and med-20, also between pre-5 and med-20. See figure 1b. STATE Heart-mean (bpm) Heart-std(bmp) pre-5 69.88 3.88 med-20 68.36 2.81 post-5 69.55 4.13 t-value test (pre-med) 0.0694 0.0003 t-value test (pre-post) 0.7934 0.3656 t-value test (post-med) 0.3193 0.0001 Table 1. The difference of Heart rate (mean and SD) in before (pre-5), during (med-20) and after (post-5)mindfulness meditation. We find significant change in standard deviation (SD) of heart rate between meditation and non-meditation mental states, as shown in table 1. The study provides insights into the underlying neurophysiological mechanisms of mindfulness meditation using wearable EEG devices. It demonstrates that in term of EEG measurement, spectrum frequency can be more sensitive than spectrum power; also heart rate variability as measured by SD is more sensitive to mean of HR. The proposed study contributes to the literature by using wearable EEG devices to collect data in a more accessible and convenient manner.

The aim of this cross-sectional study was to assess the influence of the maturity status on speed, explosive power and change of direction (COD) in 13-year-old football players. Ninety-eight male players (age: 13.1 ± 1.0 y) were divided into late, average, and early maturation groups. Physical fitness testing included the following variables: 10 and 30-meter sprint time and maximum speed in the 20-30 m segment of the 30-meter sprint test, the T-test time, countermovement jump height and horizontal distance in the triple jump. The data showed a significant effect of maturity status on performance in three parameters: in maximum speed in the 20-30 m section (p = 0,024), however, the only significant differences were found between the early-maturation group and average-maturation group (p = 0.033); in the COD (p = 0.024), where significant differences were confirmed between the late-maturation group and the average-maturation group (p = 0.033); in the unilateral triple jump distance of the dominant and non-dominant (p = 0,007 and p = 0.001, respectively) lower limb. For both limbs, significant differences between the late-maturation group and average maturation group (p = 0.005 and p = 0.013, respectively) as well as the late-maturation group and early-maturation group (p = 0.007 and p = 0.045, respectively) were proved. These results indicate that maximal speed, COD speed and unilateral lower limb reactive strength are moderated by biological age in football players aged 13 years.

Neurogenesis in the adult brain plays a major role in the cognitive ability of animals including learning and memory. Poria cocos (Schw.) Wolf (P. cocos) has been known as a traditional Chinese edible medicinal herb with the potential effect to improve learning and memory. However, the effect mechanisms are still elusive. In this study, significant neuronal differentiation-promoting activities of the ethanol extracts of P. cocos (EEPC) were tested in Neuro-2a cells and mouse cortical neural stem/progenitor cells (NSPCs). Subsequently, 97 compounds of EEPC were identified using UHPLC-Q-Exactive-MS/MS. After investigation of neuronal differentiation-promoting activities of 4 major compounds (Ethyl palmitoleate, L-(-)-Arabitol, Choline and Adenosine), only Choline has significant neuronal differentiation-promoting activity. In summary, we investigated the neuronal differentiation-promoting activity and chemical compositions of EEPC, the study of the neuronal differentiation-promoting effect of ether extract of P. cocos indicated P. cocos’s positive effect on learning and memory functions. This is the first investigation of the neuronal differentiation-promoting effect of ether extract of P. cocos based on similar research references.

Polyhydroxyalkanoate (PHA) co-polymers show relatively higher in vivo degradation rate compared to other PHAs thus they received a great deal of attention for a wide range of medical applications. Nanoparticles (NPs) loaded with poorly water soluble anticancer drug docetaxel (DCX) were produced using poly 3-hydroxybutyrate-co-4-hydroxybutyrate, P(3HB-co-4HB), co-polymers biosynthesised from Cupriavidus sp. USMAA1020 isolated from Malaysian environment. Three co-polymers with different molar proportions of 4-hydroxybutirate (4HB) were used: 16% (PHB16), 30% (PHB30) and 70% (PHB70) 4HB-containing P(3HB-co-4HB). Blank and DCX loaded nanoparticles were then characterized for their size and size distribution, surface charge, encapsulation efficiency and drug release. Pre-formulation studies showed that an optimised formulation could be achieved through the emulsification/solvent evaporation method using PHB70 with the addition of 1.0% PVA, as stabilizer and 0.03% VitE-TPGS, as surfactant. DCX-loaded PHB70 nanoparticles (DCX-PHB70) gave the desired particle size distribution in term of average particles sizes around 150 nm and narrow particle size distribution (PDI below 0.100). The encapsulation efficiencies result showed that at 30% w/w drug-to-polymer ratio: DCX- PHB16 NPs were able to encapsulate up to 42% of DCX; DCX-PHB30 NPs encapsulated up to 46% of DCX and DCX-PHB70 NPs encapsulated up to 50% of DCX within the nanoparticles system. Approximately 60% of DCX was released from the DCX-PHB70 NPs within 7 days for 5%, 10% and 20% of drug to polymer ratio while for the 30% and 40% drug to polymer ratios, an almost complete drug release (98%) after 7 days of incubation was observed.

Acemetacin (ACM) is a new non-steroidal anti-inflammatory drug with anti-inflammatory, analgesic, and antipyretic effects. However, the poor water solubility and gastrointestinal side effects limit its use. Recently, the co-amorphous (CAM) strategy has attracted great interest to improve solubility for poorly water-soluble drugs, and basic amino acids have the potential to protect the gastrointestinal tract. In order to develop highly efficient and low toxic ACM formulation, we propose to prepare ACM CAM, with basic amino acids (lysine, arginine and histidine) as co-formers, using a cryo-milling method. The solid-state behaviors of the ACM CAMs were characterized by polarizing light microscopy, differential scanning calorimetry and powder X-ray diffraction. Fourier transform infrared spectroscopy and molecular docking were carried out to understand the formation mechanism. Moreover, the gastro-protective effects of ACM CAMs were evaluated in a rat gastric ulcer model. The results demonstrated CAMs improved the dissolution rates of ACM compared with the neat amorphous counterpart. Furthermore, ACM CAMs are significantly effective in mitigating the ACM-induced gastric ulcer in rats, and the ulcer inhibition rates were almost 90%. More importantly, this study provided a useful method for mitigating drug-induced gastrointestinal damage and broadened the applications of drug-amino acid CAMs.

Background: The febrile patient from tropical areas, in which emerging arboviruses are endemic, represent a diagnostic challenge and potential co-infections with other pathogens (i.e bacteria or parasites) are usually overlooked. Objectives: We present a case of an elderly woman diagnosed with dengue, chikungunya and Leptospira interrogans co-infection. Study Design: Case report. Results: An 87-year old woman from Colombia complained of upper abdominal pain, arthralgia, myalgia, hyporexia, malaise and intermittent fever accompanied with progressive jaundice. She had a medical history of chronic heart failure (Stage C, NYHA III), without documented cardiac murmurs, right bundle branch block, non-valvular atrial fibrillation, hypertension, and chronic venous disease. Her cardiac and pulmonary status quickly deteriorated after 24 hours of her admission without electrocardiographic changes and she required ventilatory and vasopressor support. In the next hours the patient evolved to pulseless electrical activity and then she died. Dengue IgM, NS1 ELISA, MAT for Leptospira interrogans and RT-PCR for chikungunya, were positive. Discussion: This case illustrates a multiple co-infection in a febrile patient from a tropical area of Latin America that evolved to death.

The onset and progression of the salivary and gut microbiota, the transmission and the impact of the salivary microbiota on the development of early fecal microbial communities was herein explored. We characterized the microbiota of 82 faecal and 80 salivary samples, collected from 82 healty newborns at birth, 7, 15, 30, 90 and 180 days of life, by 16S rRNA targeted-metagenomics approach. Correlation heat-maps and co-occurrence networks were used to investigate microbial taxa relationship in saliva, gut and between the two ecosystems. In saliva microbiota, Streptococcus and Staphylococcus appeared as early commensals, dominating this ecosystem through the time, while Fusobacterium, Prevotella, Porphyromonas, Granulicatella and Veillonella were late colonizers. anaerobes as Enterobacteriace, Staphylococcus and Streptococcus, were gut microbiota pioneers, followed by the anaerobic Bifidobacterium, Veillonella, Eggerthella and Bacteroides. Streptococcus, Staphylococcus and Veillonella were shared by gut and saliva ecosystems (core microbiota). Early saliva and gut microbiota seem to evolve independently driven by local adaptation strategies, with the only exception for the oral Streptococcus and Veillonella genera, involved in gut microbiota development as seeding species. A more comprehensive knowledge of how oral microbiota may impact pathophysiological conditions of gut microbiota may open new avenues on the design of postbiotics.

Drug abuse is a major issue worldwide. Methylphenidate (MPH) and alprazolam (ALZ) are commonly prescribed drugs for the treatment of ADHD and anxiety disorders, respectively. The limited studies suggest that abusers primarily use benzodiazepines to counteract adverse effects associated with methylphenidate usage. The main aim of this study was to investigate the interaction of drugs with DNA using spectroscopic methods. Female Wistar rats were administered with MPH (10, 20, 40 mg/kg) and ALZ (5, 10, 20 mg/kg) alone and in combination for a period of 28 days. The FT-IR and UV results reveal some spectral changes in a dose-dependent manner, which indicates interactions of drugs with DNA. Thus, the changes in spectral peaks provide some insight into the mechanism of the interaction of drugs with DNA.

The accurate wellbore pressure control not only prevents from lost circulation/blowout and fracturing formation by managing density of drilling fluid, but also improves productivity by mitigating reservoir damage. The geothermal pressure calculated by constant parameters for geothermal well would bring big error easily, as the changes of physical, rheological and thermal properties of drilling fluids with temperature were neglected. This paper researches the wellbore pressure coupling by calculating the temperature distribution with existed model, fitting the rule of density of drilling fluid with temperature and establishing mathematical models to stimulate the wellbore pressures, which is expressed as the variation of Equivalent Circulating Density (ECD) under different conditions. With this method, temperature and ECDs in the wellbore of the first medium-deep geothermal well ZK212 Yangyi Geothermal Field in Tibet were determined, and the sensitivity analysis was simulated by assumed parameters, i.e. circulating time, flow rate, geothermal gradient, diameters of wellbore, rheological models and regimes, the results indicated the geothermal gradient and flow rate were the most influence parameters on the temperature and ECD distribution, and additives added in drilling fluid should be careful which would change the properties of drilling fluid and induce the temperature redistribution. To make sure the safe drilling, velocity of pipes tripping into the hole, depth and diameter of wellbore are considered to control the surge pressure.

Green leaf volatiles (GLVs) are important in giving grape a fresh and green aroma. But the changes in GLVs during the phenological development of grapevines are not well known. This study analysed the GLVs and transcription levels of associated biosynthetic genes in six grape species from the Loess Plateau region at five stages of maturation. Thirteen GLVs were detected, showing unique patterns for each grape type at various growth phases. The primary components in six grapes were (E)-2-Hexenal, (E)-2-Hexen-1-ol, and Hexanal. With the exception of Cabernet Franc in 2019, the overall GLV contents of the six types generally increased during growth and development, peaking or stabilizing at harvest. And Sauvignon Blanc, Cabernet Gernischt, and Cabernet Sauvignon exhibited higher total contents among the varieties. Correlation analysis revealed a strong positive correlation between the levels of Hexanal, 1-Hexanol, (E)-2-Hexen-1-ol, (Z)-3-Hexenyl acetate, Nonanal, and (E, E)-2,6-Nonadienal and the expression of VvHPL and VvAAT genes in the LOX-HPL pathway. Specifically, VvHPL emerges as a potential candidate gene responsible for species-specific differences in GLV compounds. Comprehending the changing patterns in the biosynthesis and accumulation of GLVs offers viticulturists and enologists the opportunity to devise targeted strategies for improving the aromatic profile of grapes and wines.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

The identification of a new virus Kiparis-144 (KiparisV) in a half-fed tick I persulcatus, removed from a person in the south of the Russian Far East, determined the goal of further research - to study its role in human pathology and the characteristics of its behavior in the tick microbiome. An ELISA study of 439 blood samples from people affected by tick bites indicated a fairly frequent (up to 16.4±1.7%) encounter of people with the KiparisV virus in the territory of natural foci of the Primorsky Territory. It has been shown that this virus, when mono-infected, can cause clinical symptoms characteristic of acute respiratory diseases. During co-infection under the influence of the KiparisV, there was an increase in the activity of Borrelia spp. with the constant production of antibodies to them only of the IgM class and clinical symptoms of Lyme disease for one year (observation period). Electron microscopy of the KiparisV found in a tick removed from a patient showed a picture of the relationship of the KiparisV (up to 100 nm in size) with unknown representatives of the tick microbiome - pathogens of a viral or bacterial nature. In a comparative aspect, a similar electron microscopic picture of the interaction of the KiparisV virus with a known pathogen of viral nature, the ectromelia virus (ECTV), is presented. The importance of the electron microscopy method in describing the tick microbiome is shown. Thus, it has been established that when co-cultivated in the system the helper-virus KiparisV probably tends to use another pathogen of the tick microbiome for its reproduction, influencing its pathogenicity.

Fermented foods have long been known to have immunomodulatory capabilities and fermentates derived from the lactic acid bacteria of dairy products can modulate the immune system. We have used skimmed milk powder to generate novel fermentates using Lb. helveticus strains SC234 and SC232 and we demonstrate here that these fermentates can enhance key immune mechanisms that are critical to the immune response to viruses. We show that our novel fermentates SC234 and SC232 can positively impact on cytokine and chemokine secretion, nitric oxide (NO) production, cell surface marker expression, and phagocytosis in macrophage models. We demonstrate that fermentates SC234 and SC232 increase the secretion of cytokines IL-1β, IL-6, TNF-α, IL-27, and IL-10, promote an M1 proinflammatory phenotype for viral immunity via NO induction, decreases chemokine expression of Monocyte Chemoattractant Protein (MCP), increasing cell surface marker expression, and enhance phagocytosis in comparison to their starting material. These data suggest that these novel fermentates have potential as novel functional food ingredients for the treatment, management and control of viral infection.

In this paper, the concept of absolute airspace is further elaborated, and the time transform effect, the frequency transform relation of clock timing, and the principle of Doppler effect of special relativistic light are analyzed and demonstrated. Based on the concept of absolute airspace, a new and accurate Doppler effect relation of light (electromagnetic wave) is proposed. It is proved that there is a synchronous relationship between the time shift effect and the frequency change of the timing inside the clock. When the light (electromagnetic wave) source is in motion, the Doppler effect includes two physical mechanisms: the frequency change caused by time transformation effect and the frequency change caused by relative motion. When the light source is in motion, the Doppler effect of the light there are some differences in different directions due to the rotation of the earth. The relation of Doppler effect of special relativistic light is only a highly approximate relation, and its theoretical basis, special relativity, is flawed in principle.

In tropical developing regions, typhoid fever and malaria often co-occur, posing serious health risks. The two illnesses have similar symptoms, which makes diagnosis and treatment more difficult. Through a thorough analysis of existing literature on typhoid fever, malaria, and co-infection, including research articles, case studies, and review papers, this review seeks to understand the dynamic interactions between typhoid fever and malaria co-infection. The review highlights important problems with co-infection between typhoid and malaria, such as higher morbidity and death, diagnostics-related challenges, and antibiotic resistance. Overlapping symptoms and limitations in current diagnostic tests impede accuracy. Treatment plans are made more difficult by the advent of typhoid strains that are resistant to drugs. The analysis concludes by highlighting the necessity of developing more sensitive and specific diagnostic methods in order to accurately diagnose co-infections. Going forward, the review emphasizes the need for more investigation into the immunological connections between malaria and typhoid illnesses. Essentially, this paper offers a thorough summary of the difficulties and possibilities related to co-infection between typhoid and malaria. It provides a framework for upcoming studies and initiatives that seek to improve public health and patient outcomes in the face of these intricately linked health problems.

New setting is introduced to study types of coloring numbers, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic hypergraphs. Different types of procedures including neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs are proposed in this way, some results are obtained. General classes of neutrosophic hypergraphs are used to obtain chromatic number, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic hypergraphs. Using colors to assign to the vertices of neutrosophic hypergraphs and characterizing representatives of the colors are applied in neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs. Some questions and problems are posed concerning ways to do further studies on this topic. Using different ways of study on neutrosophic hypergraphs to get new results about number, degree and co-degree in the way that some number, degree and co-degree get understandable perspective. Neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs are studied to investigate about the notions, coloring, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs. In this way, sets of representatives of colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges have key points to get new results but in some cases, there are usages of sets and numbers instead of optimal ones. Simultaneously, notions chromatic number, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges are applied into neutrosophic hypergraphs, especially, neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs to get sensible results about their structures. Basic familiarities with neutrosophic hypergraphs theory and hypergraph theory are proposed for this article.