Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

An analysis of the stiffness theory reveals that coal mass compression bumps occur only when both the failure criterion and the stiffness criterion are simultaneously satisfied. Then a new structural factor called uneven stiffness coal seam structure (USCS) is proposed, which consists of an uneven stiffness coal seam along with continuous roof and floor. The USCS serves the dual functions of pressure concentration and stiffness reduction. The former facilitates stress concentration from the low stiffness zone (LSZ) to the high stiffness zone (HSZ), thus raising the risk (rF) of failure. The latter reduces the stiffness of the surrounding rock of the HSZ, allowing the system to meet the stiffness criterion even with a hard roof, thereby reconciling the contradiction between the stiffness theory and engineering experience and raising the risk (rI) of instability. The HSZ of the USCS, including thinning zones, bifurcating areas, magmatic intrusion areas, and remnant pillar affected areas, is more susceptible to coal bump incidents than a conventional coal seam. Mechanical analysis and simple numerical simulations validate the pressure concentration and stiffness reduction functions of the USCS. The results demonstrate the following: 1) The normal stress of the HSZ positively correlates with ER, HR, KH, and SL, but negatively correlates with KL and SH; The stiffness of surrounding rock of the HSZ negatively correlates with HR, KH, SL, and SH, but positively correlates with ER and KL. 2) Failures within the HSZ of the USCS enables the roof strata to release bending deformation energy without undergoing fracturing. 3) The alignment between the HSZ of an existing USCS and the HSZ of an artificial USCS advancing with the working face intensifies stress concentration and reduces stiffness, thereby significantly increases the risk (rCB) of coal bump. By applying the stiffness theory and relevant USCS findings, new explanations can be provided for engineering phenomena such as the time-delayed coal bumps, the inefficient pressure relief in ultra thick coal seams, and the “microseism deficiency” observed prior to certain coal bumps.

With the gradual improvement of coal mining efficiency, the disturbance of groundwater system caused by the high-intensity mining mode also increases, which is a more severe challenge to the prevention of mine safety and the protection of water resources in mining areas. How to accurately describe the dynamic changes of the groundwater system under mining and quantitatively predict mine water inflow is a major problem in the current research. Based on the full analysis of the response characteristics of groundwater system to the extraction disturbance, this paper forms a kind of method to establish a mine hydrogeological conceptual model that can accurately represent the water inrush process, and uses the MODFLOW non-structural division grid to accurately characterize the formation structure, and finally make accurate water inflow prediction. Taking the Caojiatan Coal Mine in Shaanxi Province, China as an example, a numerical model of unstructured mine water inrush was established for the first time, and the changes of water inflow source and water inflow intensity were quantitatively evaluated. Compared with the traditional water inflow prediction method, it is found that the prediction accuracy is improved by 12%~17% by detailing the response characteristics of complex groundwater system under high-strength coal seam mining conditions. The method is of great significance and promotion value for the comprehensive understanding of the disturbance characteristics of human underground engineering activities, such as coal mining, on the groundwater system, and for accurately predicting water inflow.

Serious damage caused by floor heave in the coal given chamber of a vertical coal bunker is one of the challenges faced in underground coal mines. Engineering practice shows that it is more difficult to maintain the coal given chamber (CGC) than a roadway. More importantly, repairing the CGC during mining practice will pose major safety risks and reduce production. Based on the case of the serious collapse that occurred in the bearing structure of the CGC at the lower part of the 214# coal bunker in Xiashijie mine, China, this work analysed (i) the main factors influencing floor heave and (ii) the failure mechanism of the load-bearing structure in the CGC using FLAC^2D numerical models and expansion experiment. The analysis results indicate that: the floor heave, caused mainly by mine water, is the basic reason leading to the instability and repeated failure of the CGC in the 214# coal bunker. Then a new coal bunker, without building the CGC, is proposed and put into practice to replace the 214# coal bunker. The FLAC^3D software program is adopted to establish the numerical model of the wall-mounted coal bunker (WMCB), and the stability of the rock surrounding the WMCB is simulated and analysed. The results show that: (1) the rock surrounding the sandstone segment is basically stable. (2) The surrounding rock in the coal seam segment, which moves into the inside of the bunker, is the main zone of deformation for the entire rock mass surrounding the bunker. Then the surrounding rock is controlled effectively by means of high-strength bolt–cable combined supporting technology. According to the geological conditions of the WMCB, the self-bearing system, which includes (i) H-steel beams, (ii) H-steel brackets, and (iii) self-locking anchor cables, is established and serves as a substitute for the CGC to transfer the whole weight of the bunker to stable surrounding rock. The stability of the new coal bunker has been verified by field testing, and the coal mine has gained economic benefit to a value of 158.026174 million RMB over three years. The new WMCB thus made production more effective and can provide helpful references for construction of vertical bunkers under similar geological conditions.

In the steeply inclined and extremely thick coal seams (SIETCS) mined using the horizontal sublevel top-coal caving (HSTCC) method, the uncertainty of gas emission is a safety threat to the mining operations. In order to reduce the occurrence of accidents, the determination of gas emission is crucial. In this paper, we first proposed a prediction model for workers at the floor coalbed to calculate gas emission on site. We then put forward a finite element numerical simulation for researchers to predict gas emission from the floor coalbed. At last, we measured gas emitted from the floor coalbed of SIETCS in Wudong Coal Mine in a specific mining period and used the data to verify the applicability and accuracy of these two gas-emission prediction methods. The results showed that the gas emission from Wudong Coal Mine was 1.08 m³/min calculated based on the prediction model and 1.07 m³/min obtained using the user-defined integration method. Both methods have their own advantages, disadvantages and applicable objects, and are important in predicting gas emission from SIETCS mined using HSTCC method.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

Paleopeat-forming environments have an important effect on the dispersion and enrichment of trace elements in coal. The C3 coal seam of the Xuanwei Formation in eastern Yunnan was used as a case study to reconstruct the paleopeat-forming environment based on the coal facies parameters and geochemical characteristics, and its influence on trace element (including rare earth elements and yttrium, REY) enrichment was investigated. The C3 coal was classified as medium rank coking coal with an ultra-low moisture content, medium-high-ash yield, and low-medium volatile content. Compared to the average values for Chinese coals, Cu and V were enriched and Co was slightly enriched in the C3 coal. Compared with the average values for world coals, Cu and V were enriched, while several other trace elements were slightly enriched, including Co, Hf, Nb, Sc, Ta, Zn, and Zr in the C3 coal. The C3 coal was deposited in a low peat mainly limno-telmatic swamp, with deep water, weak hydrodynamic conditions, brackish to salty water, and reducing conditions. Trace elements, including Cu, V, Hf, Nb, Sc, Ta, Zr, and REY, are typically enriched in a limno-telmatic environment with fresh water, and reducing and weak hydrodynamic conditions. Additionally, REY and V are also significantly enriched in brackish water limno-telmatic conditions with the same depositional environment.

The escalation of mining activities in the karst regions of Guizhou Province has heightened the occurrence of water-inrush incidents in deep coal mines. This study focused on water-inrush phenomena within the Xinhua mining area of Jinsha County, Guizhou Province, aiming to investigate the sources of these incidents. The findings indicated that the overlying limestone of the Changxing Formation in the coal seam served as a vulnerable aquifer under certain conditions, leading to water inrushes. The analysis of the spatiotemporal distribution patterns of water-inrush incidents at the working face indicated that previous mining operations damaged the shallow Changxing Formation limestone, resulting in the accumulation of goaf water and the formation of numerous mining-induced fractures. These fractures served as rapid conduits for water inrushes from both atmospheric precipitation and underground sources at the deep working face. The examination of surface water and mine water quality demonstrated that both exhibited similar characteristics, predominantly featuring bicarbonate, sulfate, and sodium compositions. Investigation into the relationship between mine water inflow and atmospheric precipitation established that atmospheric precipitation influenced the mine water supply cycle, with a replenishment period of ~10 months during the operational phase of the Jinyuan Coal Mine and about one month post-closure. The fractures induced by mining activities within the Changxing Formation limestone facilitated water flow, with atmospheric precipitation serving as the primary water source for the mine. This study offered a valuable scientific foundation for addressing water-related damage resulting from atmospheric precipitation in mines susceptible to water inrushes under analogous hydrogeological conditions.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

Optimizing the NACA0015 airfoil which is widely applied in small-scale vertical axis wind turbine to make it has a better aerodynamic performance. In the optimization process, using CST parameterization method to perturb the airfoil geometry, the thickness and camber of the airfoil are selected as the constraint, and the value of the maximum tangential force coefficient is chosen as the objective function, the genetic algorithm based on non-dominated sorting (NSGA-II)is selected as an optimization method, calculates the aerodynamic performance of the airfoil by applying the approach of combining XFOIL program and Viterna-Corrigan post-stall mode ,and establishes the optimizing process by the optimization software modefrontier for NACA0015 airfoil’s muti-point optimization, validate the airfoil’s performance with CFD finally. The result illustrates that, by comparing with the NACA0015 airfoil, the optimized airfoil’s lift to drag ratio is improved over a wide range of attack angles, the stall performance is more gentle. The maximum lift coefficient, the maximum lift-drag ratio and the maximum tangential force coefficient are increased by 7.5%,9 and 8.87%, respectively. The optimized airfoil has a wide variable condition performance, more suitable for the operating conditions of a vertical axis wind turbine. Finally, predict the rotor efficiency with optimized airfoil and NACA0015 airfoil for different tip speed ratios and different solidities with multiple streamtube model, the result shows the rotor with optimized airfoil has a higher efficiency.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

Bamboo engineering materials are green, high-strength, tough, durable, and structurally safe, and have promising application prospects in various modern green and low-carbon buildings. To invest the vibration behavior of new bamboo bundle veneer -laminated lumber (BLVL) for use in floor slabs, this study designed two kinds of full-scale vibration tests under a pedestrian load: an extraction hammer impact test, and a static concentrated load test, it is expected to provide theoretical and data support for the application of bamboo bundle veneer laminated composite materials in the construction field. The results showed that the self-oscillation frequency and mid-span deflection of the BLVL composite met the requirements of multiple relevant regulations when used as the structural material of floor slabs. The BLVL floor slab had a higher flexural stiffness and better vibration-damping performance than the OSB floor slab. The first-order self-oscillation frequency of the BLVL composite floor slab was 13.769 Hz, the damping ratio of the first three orders of modalities was 1.262–2.728%, and the maximum static deflection in the span of the joist was 0.932 mm under a 1 kN concentrated load. The 1 kN static deflection of the BLVL was reduced by 22.33%, and the root mean square (RMS) acceleration of the walking load response was significantly lower than that of the OSB floor slab. The preparation of BLVL composite materials by homogeneous lamination of bamboo bundle veneer and wood veneer may help improve the vibration behavior of bamboo-wood structures such as floor slabs and walls.

5-(4-aminophenyl )-2-amino -1,3,4-thiadiazole was prepared by reaction of Thiosemicarbazide with 4-amino benzoic acid under reflux condition for 7 hours. The compound which has been synthesized successfully was subjected to addition reaction with 4-(Dimethylamino) benzaldehyde under reflux condition for 6 hours to synthesize Schiff bases. These compounds was characterized by using FTIR) and evaluated for their anticancer activity. The effect of (1, 3, 4-thiadiazole derivative) on the activity of malignant cells was studied by using different types of cell lines [Breast cancer, and human prostate cancer]. And was used the Electron microscope to show that the effect of the derivative on the cancer cells before and after 3 days of the injection time. It was found that the Schiff base of thiadiazole-1,3,4-(Dimethylamino)benzylidineamino]- [4-2-phenyl]amino was effective in reducing the size and density of malignant cells. That of 46.7 while in breast ) 145(DUprostate for growth inhibition produce of equal 85.9 µg/ml.

Reducing waiting times is crucial for ports to be efficient and competitive. Important causes of waiting times are cascading interactions between realistic hydrodynamics, accessibility policies, vessel-priority rules, and detailed berth availability. The main challenges are determining the cause of waiting and finding rational solutions to reduce waiting time. In this study, we focus on the role of the design depth of a channel on the waiting times. We quantify the performance of channel depth for a representative fleet rather than the common approach of a single normative design vessel. It relies on a mesoscale agent-based discrete-event model that can take processed Automatic Identification System and hydrodynamic data as its main input. The presented method’s validity is assessed by hindcasting one year of observed anchorage area laytimes for a liquid bulk terminal in the Port of Rotterdam. The hindcast demonstrates that the method predicts the causes of 73.4% of the non-excessive laytimes of vessels, thereby correctly modelling 60.7% of the vessels-of-call. Following a recent deepening of the access channel, cascading waiting times due to tidal restrictions were found to be limited. Nonetheless, the importance of our approach is demonstrated by testing alternative maintained bed level designs, revealing the method’s potential to support rational decision-making in coastal zones.

The physical properties of coal reservoirs are the main restrictions to exploration and development of CBM. The study of the physical characteristics of coal reservoirs and their controlling factors is of great significance to the safe and efficient development and utilization of CBM resources in the mining area. The Pingdingshan No. 10 coal mine was chosen for this study because of its better gas production effect at the test wells. The reservoir properties of the main coal seams of the No. 10 coal mine were tested and analyzed to comprehensively evaluate the reservoir properties. The results indicate that (1) The gas content and methane purity of the No. 4 coal seam are significantly higher than the No. 2 seam, and therefore they have better development potential than the No. 2 seam; (2) The average adsorption time of the No. 2 coal seam is less than that of the No. 4 seam, making it easier to reach the peak production capacity of CBM wells in the short term, but is not conducive to long-term stable production of CBM. The Langmuir volume of the No. 2 coal seam samples was significantly greater than for the No. 4 coal seam; however, the No. 4 coal seam contains about three times the amount of gas in the No. 2 seam; (3) All three coal seams have high porosity, which is favorable for large amounts of CBM adsorption and storage. Micropores predominate, transitional pores are less frequent, and a few mesopores occur; macropores are the least common. Samples from the No. 4 seam contained the highest proportion of micropores; (4) Organic pores were common in the all coal samples, with pore diameters not more than 30 µm, mainly concentrated between 50.5 and 1000 nm. Microfractures with aperture less than 70 nm were relatively frequent, mainly in the 50–65 nm range. A large number of the nanoscale microfractures were curved or jagged; (5) Fractures in the No. 2 and No. 4 coal seam samples with widths of 50 nm to 20 µm were more developed, and many were filled with kaolinite, quartz and other minerals; (6) The samples contained mostly layered silicate minerals (kaolinite), with hard granular minerals (quartz) next, and a very small quantity of iron-type minerals such as siderite and pyrite in dendritic form. The results of this study can provide a reference basis for the large-scale development and utilization of subsequent CBM wells.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Stress urinary incontinence (SUI) influences the quality of life of women. The research applied ICIQ LUTS qol (The International Consultation Incontinence Questionnaire Lower Urinary Tract Symptoms quality of life) as a tool to measure the quality of life (QOL) of patients with stage 1 SUI in many areas. 140 perimenopausal women who participated in a urodynamic test at Department of Gynecology, Endocrinology and Gynecologic Oncology, Pomeranian Medical University, Police, Poland in the years 2013-2015 were enrolled in the study. Patients were divided into two groups: A and B. Two questionnaires were applied: the author’s original questionnaire and the standardized ICIQ LUTS qol. Gymnastic plans were recommended 4 times per week for the period of 3 months. The plan for group A included the exercises of pelvic floor muscles (PFM) with the simultaneous tension of the transverse abdominal muscle (TrA) and for group B included the exercises of PMF without TrA. The evaluation of the quality of life of patients with stage 1 SUI with the use of ICIQ LUTS qol among patients from groups A and B after therapy showed a significant improvement in most areas. More impact is observed in the physiotherapy of both PFM with TrA.

In this part of the series of two papers, we extend the theorems discussed in part I for infinite series. We then use these theorems to develop distinct novel results involving the Hurwitz zeta function, Riemann zeta function, Polylogarithm and Fibonacci numbers. In continuation, we obtain some zeros of the newly developed zeta functions and explain their behaviour using plots in complex plane. Furthermore, we provide particular cases for the theorems and corollaries which show that our results generalise the currently available functions and series such as the Riemann zeta function and the geometric series. Finally, we provide four miscellaneous examples to showcase the vast scope of the developed theorems.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

Arc sensors have been used in seam tracking and widely studied since the 80s; commercial arc sensing products for T and V shaped grooves have been developed. However, it is difficult to use these arc sensors in narrow gap welding because arc stability and sensing accuracy are not satisfactory. Pulse gas melting arc welding (P-GMAW) has been successfully applied in narrow gap welding and all position welding processes, so it is worthwhile to research P-GMAW arc sensing technology. In this paper, we derived a linear mathematical P-GMAW model for arc sensing, and the assumptions for the model are verified through experiments and finite element methods. Finally, the linear characteristics of the mathematical model were investigated. In torch height changing experiments, uphill experiments, and groove angle changing experiments the P-GMAW arc signals all satisfied the linear rules. In addition, the faster the welding speed, the higher the arc signal sensitivities; the smaller the groove angle, the greater the arc sensitivities. The arc signal variation rate needs to be modified according to the welding power, groove angles, and swing or rotate speed.

With the renewed interest for lunar surface exploration, the European Space Agency envisions to stimulate the creation of lunar communications and navigation services (LCNS) to enable, among others, autonomous navigation capabilities for lunar rovers. As the number of satellites foreseen in such a service is much smaller compared to Earth based global navigation satellite systems (GNSS), different complementary technologies are pursued to improve the attainable navigation accuracy for lunar rovers. One way to improve the position accuracy provided by the LCNS satellites is to constrain the vertical position using a high resolution digital elevation model (DEM). This article presents the results of a variance covariance analysis of an extended Kalman filter (EKF) implementation in which the LCNS ranging measurements are used together with DEM from the LRO LOLA instrument. Assuming a realistic orbit determination and time synchronization (ODTS) accuracy of the LCNS satellites, the usage of a navigation grade IMU and an oven controlled crystal oscillator (OCXO), a 3-sigma position accuracy of less than 10 meters can be obtained. Furthermore, the availability is substantially improved as the DEM aided solution enables a position solution in case of only 3 visible satellites.

Research has been growing on object detection using semi-supervised methods in past few years. We examine the intersection of these two areas for floor-plan objects to promote the research objective of detecting more accurate objects with less labelled data. The floor-plan objects include different furniture items with multiple types of the same class, and this high inter-class similarity impacts the performance of prior methods. In this paper, we present Mask R-CNN based semi-supervised approach that provides pixel-to-pixel alignment to generate individual annotation masks for each class to mine the inter-class similarity. The semi-supervised approach has a student-teacher network that pulls information from the teacher network and feeds it to the student network. The teacher network uses unlabeled data to form pseudo-boxes, and the student network uses both unlabeled data with the pseudo boxes and labelled data as ground truth for training. It learns representations of furniture items by combining labelled and unlabeled data. On the Mask R-CNN detector with ResNet-101 backbone network, the proposed approach achieves mAP of 98.8%, 99.7%, and 99.8% with only 1%, 5% and 10% labelled data, respectively. Our experiment affirms the efficiency of the proposed approach as it outperforms the fully supervised counterpart using only 10% of the labels.

This paper presents technical solutions to increase Industry 4.0 maturity. Within the “5G-Enabled Manufacturing” project, a 5G network has been deployed at the shop floor to enable fast and scalable connectivity. This network was used to connect a grinding machine to a private cloud to enable visibility and transparency of the production data, which is the basis for Industry 4.0 and smart manufacturing. Results indicate a present lack of commercially available product independent solutions for interconnection and data transfer despite the availability of open standards and well-documented demonstrator projects. The solution is described and discussed regarding technical interoperability, focusing on the system layout, communication standards, and open systems. From the discussion, it is derived that manufacturing end-users are in need to expand and further internalize knowledge on future information and communication technologies to reduce their dependency on equipment and technology providers.

Due to the still large number of patients diagnosed with pelvic neoplasms (colorectal, gynecological, and urological) in advanced stages right from the initial diagnosis, surgery represents the mainstay of treatment, often implying wide, eventually multi-organ resections in order to achieve negative surgical margins. Perineal wound morbidity, particularly in extralevator abominoperineal excision, leads to complications and local infection rates of up to 40%. Strategies to reduce postoperative wound complications are pursued to address this issue.The VRAM flap remains the gold standard for autologous reconstruction after pelvic oncological resection; it was initially designed for abdominal wall defects and later expanded for large pelvic tissue defects.The flap's application is based on its physical characteristics, including abundant tissue and a generous skin paddle, which effectively obliterates dead space after exenterations. The generous skin paddle offers good cosmetic and functional outcomes at the recipient site.This article describes the case of a patient histopathologically diagnosed with stage IIIA squamous cell carcinoma of the uterine cervix who received multimodal onco-surgical treatment. The surgical mainstay of this treatment is pelvic exenteration. Pelvic reconstruction after this major surgery was performed using a vertical flap with the rectus abdominis.

This study presents preliminary findings on the physicochemical, calorific, and thermal properties of a newly discovered coal from Obomkpa town in Aniocha-North Local Government Area of Delta State in Nigeria. The Obomkpa (BMK) coal sample was subjected to fuel characterisation through ASTM standards and techniques for determining elemental, proximate, and calorific coal properties. The results indicated that BMK coal contains high carbon, oxygen, volatile matter, fixed carbon, and ash. The higher heating value of BMK was 19.66 MJ/kg, which indicates it could be ranked as either lignite A or subbituminous C coal. The thermal properties indicated that BMK experienced significant mass loss (M_L) under oxidative (combustion) and non-oxidative (pyrolysis) conditions due to thermal degradation of organic rock macerals (inertinite and vitrinite). Furthermore, BMK experienced mass loss (M_L=59.27%–76.56%) along with residual mass (R_M = 23.44–40.73%) under oxidative (combustion) and non-oxidative (pyrolysis) conditions. Thermal degradation occurred in three (3) stages; drying (30 °C to 200 °C), devolatilization (200 °C – 500 °C and 600 °C), and lastly, coke degradation and ash formation. Furthermore, the DTG peaks for the drying and devolatilization of BMK during the oxidative (combustion) process occurred at lower temperatures compared to the non-oxidative (pyrolysis) process. Hence, the results submit oxidative (combustion) is a more thermally efficient process compared to the non-oxidative (pyrolysis) process. Lastly, the findings indicate BMK is a potential feedstock material for future coal power generation, steel, iron ore or cement production.

Coal currently accounts for over 38% of electric power generation around the globe. Hence, it is a significant critical contributor to socio-economic growth and development, particularly in the BRIC economies. The success of the coal energy in these nations in addition to the discovery of vast new coal deposits have revived Nigeria’s interest in coal power. However, there is lack of comprehensive data on the pollution emission profiles, along with the physicochemical, thermal, and kinetic properties of Nigerian coals as required for power plant operations. Therefore, this paper presents preliminary findings on the physicochemical, microstructural, mineralogical and thermal properties of Owukpa (WKP) coal from Benue State in Nigeria. The results showed that WKP contains high compositions of combustible elements and heating value but low pollutant elements. Furthermore, thermal degradation revealed high conversion efficiencies particularly under oxidative conditions as required for electric power generation through combustion.

Pore-fractures network play a key role in coalbed methane (CBM) accumulation and production, while the impacts of coal facies on the pore-fractures network performance are still poorly understood. In this work, the research on the pore-fracture occurrence of 38 collected coals from Sangjiang-Muling coal-bearing basins with multiple techniques including mercury intrusion porosimetry (MIP), micro-organic quantitative analysis, and optic microscopy, and its variation controlling of coal face were studied. The MIP curves of 38 selected coals indicating pore structures were subdivided into three typical types including type I of predominant micropores, type Ⅱ of predominant micropores and macropores with good connectivity and type Ⅲ of predominant micropores and macropores with poor connectivity. For coal facies, there are three various coal facies were distinguished, which include lake shore coastal wet forest swamp, the upper delta plain wet forest swamp, tidal flat wet forest swamp with Q-cluster analysis and tissue preservation index - gelification index (TPI-GI) and Wood index - groundwater influence index (WI -GWI). The results show there is positive relationship between tissue preservation index (TPI), wood index (WI) and mesopores (102nm-103nm), while a negative relationship between TPI, WI and macropores/fractures. In addition, groundwater level fluctuations can control the development of type C and D fractures, and the frequency of type C and D fractures shows an ascending trend with increasing GWI, which may be caused by the mineral hydration of the coal. Finally, from the perspective of the pore-fractures occurrence in CBM reservoirs, the wet forest swamp of upper delta plain is considered to be the optimization areas for Sanjiang-Mulinghe coal-bearing basins by a comparative study of various coal facies.

The introduction of innovative digital tools for supporting manufacturing processes has far-reaching effects on an organizational and an individual level due to the development of Industry 4.0. The FACTS4WORKERS project funded by H2020, i.e. Worker-Centric Workplaces in Smart Factories, aims to develop user-centered assistance systems in order to demonstrate their impact and applicability at the shop floor. To do so it is important to understand how to develop such tools and how to assess if advantages can be derived from the created ICT system. This study introduces the technology of a workplace solution that is linked to a specific industrial challenge. Subsequently, a 2-stepped approach to evaluate the presented system is discussed. Heuristics, which are an output of project “Heuristics for Industry 4.0”, are used to test if the developed solution covers critical aspects of socio-technical system design. Insights into the design, development and holistic evaluation of digital tools at the shop floor should be shown.

In municipal waterworks large amounts of waste in the form of sludge have to be discarded. This investigation focuses on the processing of ceramic floor tiles incorporated with a municipal waterworks sludge. Four floor tile formulations containing up to 10 wt. % of the municipal waterworks sludge in replacement of kaolin were prepared. The floor tile processing route consisted of dry powder granulation, uniaxial pressing, and firing between 1190 and 1250 °C using a fast-firing cycle (<60 min). The densification behavior and technological properties of the floor tile pieces as function of the sludge addition and firing temperature were determined. The development of the microstructure was followed by XRD and SEM/EDS. The results show that the replacement of kaolin with municipal waterworks sludge, in the range up to 10 wt. %, allows the production of ceramic floor tiles (group BIb and group BIIa, ISO 13006 Standard) at lower firing temperatures. These results suggest a new possibility for valorization of municipal waterworks sludge with many economical and environmental benefits.

This study presents a preliminary analysis of the chemical and thermal fuel properties of Afuze (AFZ) coal extracted from coalfields in Owan East Local Government Area of Edo State, Nigeria. The chemical properties of AFZ were examined by combined scanning electron microscopy-energy dispersive X-ray (EDX), whereas the thermal properties were deduced by thermogravimetric analysis (TGA) under flash (50 °C/min heating rate) oxidative (combustion) and non-oxidative (pyrolysis) conditions. The microstructure and morphology analysis of AFZ revealed has a compact structure comprising small-to-large, irregular shaped and exfoliated grains with a vitreous appearance typically ascribed to metal elements (Ti and Fe) kaolinite, quartz, and other clay minerals. Chemical analysis revealed carbon, oxygen, aluminium, silicon, sulphur, calcium, titanium, and iron in major and minor (trace) quantities. Thermal analysis under oxidative and non-oxidative conditions revealed degradation occurs in three stages, namely; drying or demineralisation, devolatilization or maceral degradation and the formation of char/coke or ash. Lastly, the findings showed that the temperature range for the oxidative thermal degradation process (338.58 - 756.76 °C) was higher than the non-oxidative process (378.43 - 615.34 °C). This observation can be explained by the exothermic nature of the oxidative (combustion) process, which ensures greater heat supply required to thermally soften or degrade the maceral coal components. Overall, the oxidative process yielded the residual mass (RM = 21.97%) and mass loss (ML = 78.03%). The lower ML (49.03%) but higher RM (50.97%) observed during non-oxidative degradation of AFZ could be ascribed to the largely endothermic nature of the process.

Abstract: Unusual methane emission and spontaneous combustion of coal induced by the air leakage are both hazards during mining. The most common practice has been to improve mine safety is sealing the mining fractures. In this paper, the methane and geology, coal spontaneous combustion characteristics and the coexistence of methane emission and spontaneous combustion of coal were analyzed. The preparation system of inorganic solidified foam (ISF) in field applications is studied and the working principle of generating device consists of foam generator and mixer was expounded. The technical plan of site construction is that the foam fluids was injected to respectively seal the mining fractures behind hydraulic supports, the cavities of air return corner, and the fractures nearby the coal pillar. After the foam fluids injection, the two stress values in the coal pillar eventually maintained above 15.5Mpa and 13Mpa, respectively. It indicated that the ISF can enhance the bearing stress ability of the coal pillar by transforming the stress state from two dimensional to three dimensional. The methane concentration in the air return corner and air return roadway declined significantly to 0.63% and 0.25%. The differential pressure inside and outside of the 4301(1) goaf fluctuated between -100pa to 150pa and the concentration of CO and O2 declined to 9ppm and 6%. The CO concentration in the air return corner finally reached a stable level of 6ppm. What that all means, the foam fluids can seal the air leakage and inhibit spontaneous combustion of coal effectively.

Coupled Delft3D-object model has been developed to predict object’s mobility and burial on sandy seafloor. The Delft3D model is used to predict seabed environment such as currents, waves (peak period, significant wave height, wave direction), water level, sediment transport, and seabed change, which are taken as the forcing term to the object model consisting of three components: (a) object‘s physical parameters such as diameter, length, mass, and rolling moment, (b) dynamics of rolling cylinder around its major axis, and (c) empirical sediment scour model with re-exposure parameterization. The model is compared with the observational data collected from a field experiment from 21 April to 23 May 2013 off the coast of Panama City, Florida funded by the Department of Defense Strategic Environmental Research and Development Program. The experimental data contain both objects’ mobility using sector scanning and pencil beam sonars and simultaneous environmental time series data of the boundary layer hydrodynamics and sediment transport conditions. Comparison between modeled and observed data clearly show the model capability.

In the end, this paper analyzed the economy from the investment in plant construction, raw material collection, product production and product sales. The resulting products include pyrolytic carbon, pyrolytic oil, pyrolysis gas. The results showed that when the treatment scale was 1 ton h−1, the pyrolysis plants with three loading modes will always be in a state of loss during the 20-year running time. When the processing scale was 9 ton h−1, the pyrolysis plant can be profitable in the first year. In the sensitivity analysis, the influence of three pyrolysis products on the total return on investment was explored. The results showed that the price change of pyrolysis oil has the greatest influence on the total return on investment (Total ROI) under the three loading methods, The price change of pyrolysis gas has minimal impact on the Total ROI. This study provides basic data and basis for the commercialization of coal-biomass co-pyrolysis technology and investment in plant construction.

The occurrence rate of occupational accidents caused by slipping and falling is 50% worldwide. Determining the slip safety risk is necessary to minimize the accidents caused by slipping in pedestrian walking areas. By on-site testing, this study aims to determine the slip risks of floor coverings used in walking areas with many pedestrians in public service buildings (PSB). For this purpose, on-site measurements were performed in two environments and six locations in PSB using portable GMG 200 and pendulum testers operating according to DIN 51131 and TS EN 14231 standards. These tests were performed on four-floor coverings with polished surface treatment in PSB. Since the floor coverings measured have a polished surface, it can be seen that the dynamic friction coefficients (DCOF) values are very low, and the slip risks are high. By statistically analyzing the slip test data using the K-means method, a new safety classification was made according to the usage areas of floor coverings. To minimize the risk of slip safety, especially for students, patients, and employees in PSB, it is recommended to use floor coverings with high DCOF values and low slip risk.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

This article describes the POTENTIALS project, which aimed to develop business models for the reuse of former industrial and mining sites in different regions. The project focused on the creation of eco-industrial parks as a result to enable sustainable energy production and reduce waste and pollution. A key aspect was the Territorial Impact Assessment (TIA), a new and complex policy assessment tool. Therefore, the TEQUILA (Territorial Efficiency Quality and Identity Layer Assessment) approach is used to describe the TIA and emphasizes its application in assessing the impact of EU policies and projects on territorial cohesion. It underlines the need for a differentiated understanding of the regional characteristics and potential impacts of policies; and stresses the importance of regionalized impact models for the assessment. Furthermore, the process and results of applying the TEQUILA methodology to assess the territorial impact of different scenarios of business models within the POTENTIALS project is given.

Carbon monoxide (CO) concentrations in wildfire plumes are easily measured from satellites. This gas can be used as a proxy for carbon dioxide. Forest fires play an important role in the carbon balance and in particular the CO balance. The most likely causes of mega-fires of 2003, 2012, 2021, and 2023 in the Northern hemisphere are heat waves and severe droughts associated with changes in general circulation. Here we analyze satellite data obtained by two different sounders, AIRS and TROPOMI. Different sensitivity to the lowest troposphere allows obtaining information about anthropogenic or pyrogenic contamination of the boundary layer. Shapes of areas polluted by mega-fires in 2019-2020 (Southeastern Australia) and 2021 (Central Siberia) coincide with the areas occupied by coal deposits. The Siberian Lena and Tunguska coal basins are the two largest coal fields in the world. In 2021, their combined area accounted for 90% of fire CO emission from the entire Russian Federation. So strong fires have not observed in this area before. Under- and sub-ground coal combustion may be included into the list of wildfire fuels, at least their role for ignition should be admitted. Further research is needed to assess the importance of coal fires to global climate.

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

To achieve rapid post-earthquake repair of self-centering ribbed floor flat beam frame structures, a ductile hybrid joint consisting of dog bone weakened energy dissipating steel bars connected to the upper and lower column sections through high-strength threads based on the damage control design concept is proposed. By moving the ductile energy dissipating zone out to the locally weakened section of the energy dissipating steel bars and the locally unbonded prestressed steel bars in the core area, the residual deformation was limited and the seismic performance was improved. Based on the working principle of hybrid joints, low cycle loading tests were conducted on two joint specimens to analyze the influence of lateral prestress on the seismic performance of the hybrid joints. Numerical modeling methods were used to compare the position of the energy-consuming steel bars in the composite layer and the friction performance of joints. The research results indicated that the hybrid joint had stable load-bearing, deformation, and energy dissipation capabilities, with damage primarily concentrated on the energy-consuming steel bars. Even at an inter-story displacement angle of 5.5%, the upper and lower column segments remained elastic. After unloading, the connection seam at the joint was closed, and the self-centering performance was good. When the inter-story displacement angle reached 5.5%, the lateral prestress increased from 150 kN to 250 kN, the ultimate bearing capacity of the joint increased by 16.3%, and the cumulative energy consumption increased by 30.0%. The influence of the friction coefficient of the joint surface on the structural performance was set at a threshold of 0.7. When it was less than the threshold, the ultimate bearing capacity and initial stiffness of the joint increased with an increase in the friction coefficient. After reaching the threshold, the increase in the ultimate bearing capacity of the joint slowed down, and the rate of stiffness degradation gradually accelerated. This joint had excellent seismic performance and can also achieve post-earthquake repair of structures.

A sustainable matrix based on eucalyptol essential oil/sawdust was developed and applied on one-sided laminated plywood. This finish aims to serve as a eucalyptol odor slow release. Eucalyptol odor release was monitored with gas chromatography coupled with a flame ionization detector (GC – FID: Limits of Detection and Quantification of 0.70 g/m3 and 2.11 g/m3, respectively, and with linearity up to 18.6 g/m3). Measurement of the eucalyptol odor released was performed during a six-month period and it was found that the release followed a first-order exponential decay with a decay rate constant of 0.0169 per day. The half-life was determined to be of 48 days. The granulometry and particle size porosity of sawdust were analyzed by Scanning Electron Microscopy. Sawdust size fraction between 112 – 200 μm showed best eucalyptol absorption capacity with 1:3 masses ratio (sawdust:eucalyptol). The time capacity of eucalyptol release depends of composite eucalyptol – sawdust quantity. Where this relation was determined: 15.0 grams of composite eucalyptol-sawdust by 0.8 mm diameter aperture gave 6 months of eucalyptol release, that was considered very positive, understanding high volatility of eucalyptol and a small quantity of composite for further products. The new product is characterized by a carbon footprint (considering the industry frontiers) of 5.94 kg CO2eq/m2 of plywood floor.

Object detection is one of the most critical tasks in the field of Computer vision. This task comprises identifying and localizing an object in the image. Architectural floor plans represent the layout of buildings and apartments. The floor plans consist of walls, windows, stairs, and other furniture objects. While recognizing floor plan objects is straightforward for humans, automatically processing floor plans and recognizing objects is a challenging problem. In this work, we investigate the performance of the recently introduced Cascade Mask R-CNN network to solve object detection in floor plan images. Furthermore, we experimentally establish that deformable convolution works better than conventional convolutions in the proposed framework. Identifying objects in floor plan images is also challenging due to the variety of floor plans and different objects. We faced a problem in training our network because of the lack of publicly available datasets. Currently, available public datasets do not have enough images to train deep neural networks efficiently. We introduce SFPI, a novel synthetic floor plan dataset consisting of 10000 images to address this issue. Our proposed method conveniently surpasses the previous state-of-the-art results on the SESYD dataset and sets impressive baseline results on the proposed SFPI dataset. The dataset can be downloaded from SFPI Dataset Link. We believe that the novel dataset enables the researcher to enhance the research in this domain further.

This paper presents a new framework to classify floor plan elements and represent them in a vector format. Unlike existing approaches using image-based learning frameworks as the first step to segment the image pixels, we first convert the input floor plan image into vector data and utilize graph neural network. Our framework consists of three steps. (1) image pre-processing and vectorization of the floor plan image. (2) region adjacency graph conversion. (3) graph neural network on converted floor plan graphs. Our approach is able to capture different types of indoor elements including basic elements such as walls, doors, and symbols as well as spatial elements such as rooms and corridors. In addition, the proposed method can also detect element shapes. Experimental results show that our framework can classify indoor elements with an F1 score of 95%, with scale and rotation invariance. Furthermore, we propose a new graph neural network model that takes the distance between nodes into account, which is a valuable feature of spatial network data.

The paper highlights the problems associated with the application of daylight and integral lighting in industrial facilities. In the case study of a multi-storey textile plant, we show how combined lighting (daylight and integral illumination) can be evaluated in production halls labelled F and G. These halls have large areas 54 x 54 metres, and are more than 5 meters high. There is daylight only on side through connected windows in a vertical position. In this paper we want to present case studies of these two production halls in the textile factory located in Kosice (Slovakia). These are halls that are lit through by daylight from two sides through external walls that are opposite or next to each other. The results of the case studies can be applied in similar production halls illuminated by a “bilateral” —a double-side daylight system and natural illumination through windows on two sides in a vertical position. Such a situation is typical of multi-storey buildings in light industry. The proposed approach of daylight factor calculation can also be applied to floor space in other similar buildings.

Enophthalmos is a severe complication of primary reconstruction following orbital floor frac-tures, oncological resections or maxillo-facial syndromes. The goal of secondary reconstruction is to re-store symmetrical globe positions to recover function and aesthetics. In this article we pre-sent a method of computer-assisted orbital floor reconstruction using a mirroring technique and a customized titanium or high-density polyethylene mesh, printed using computer aided manufac-turing techniques. This reconstructive protocol involves 4 steps: mirroring of the healthy orbit at the affected site, vir-tual design of a patient specific orbital floor mesh, computer-assisted manufacturing (CAD) of the implant, and surgical insertion of the device. Using a computed tomography data set, the un-injured side of the craniofacial skeleton was reflected onto the contralateral injured side, and a reconstructive orbital floor prosthesis was virtually designed on the mirrored orbital bone sur-face. The solid-to-layer (.STL) files of the prosthesis were then manufactured using Direct Metal Laser Sintering (DMLS) or Computer Numerical Control (CNC) methods, leading to the produc-tion of 10 titanium meshes and 2 high density polyethylene (HDPE) implants. Clinical outcomes were assessed using 3dMD photogrammetry and computed tomography measures in 14 treated patients. The technique described here appears to be a viable method to correct complex orbital floor de-fects needing delayed reconstruction. This article represents the prosecution of a previous study, which is part of a wider experimental protocol for orbital floor reconstruction using comput-er-assisted design-computer-assisted manufacturing (CAD-CAM) technology

A pump station is a very important flood control facility for mitigating inundation of urban lowland areas. It is not easy to secure a site to increase the capacity of a pump station in an urban area because of various limitations or to maximize the discharge capacity of the pump sump. Adding a facility to improve the pump capacity of a pump station may affect the flow characteristics, such as unexpected increases in the flow velocity and vorticity, and cause severe problems with operating the pump station. To solve those problems, anti-vortex devices (AVDs) have been developed and adopted for appropriate design standards. The Korean design criteria for AVDs are based on experience and foreign standards because not enough data on the AVD are available. In this study, the flow in the sump was numerically simulated at various AVD heights to collect information on improving the design and efficiency of a pump station. Consequently, an appropriate height for the AVD and changes in the flow pattern and vortex in the pump sump were determined and compared with 12 cases of inflow conditions with respect to the vertical location.

Abstract: Female pelvic floor dysfunction (FPFD) is a series of conditions caused by the displacement or dysfunction of the patient's pelvic organs due to defects, injuries, and deterioration of the pelvic floor supportive structures, with stress urinary incontinence and pelvic organ prolapse being the most common. The mechanism of pelvic floor dysfunction is complex and not yet fully understood, and is often related to one or more functional abnormalities of muscles, connective tissues, fascia, nerves and blood vessels. Specialized clinicians are often unable to cover the comprehensive medical professional information of various specialties such as gynecology and obstetrics, urology, anus and intestines, imaging, etc., and the systematic and comprehensive diagnosis and treatment of the disease will be limited. The application of artificial intelligence concepts in the medical field not only improves the diagnostic efficiency of physicians, but also provides reference and basis for the development of comprehensive treatment programs. This article follows and draws on the diagnosis and treatment process of pelvic floor dysfunction recommended in various guidelines, incorporates physical therapy techniques into the conventional non-surgical treatment of pelvic floor dysfunction, provides guidance for the diagnosis and treatment of pelvic floor dysfunction, and briefly introduces the clinical application and value of pelvic floor intelligent diagnosis and treatment in pelvic floor dysfunction.

Coal bottom ash (CBA) is a byproduct of coal-burning power plants. This material can be used as a fine aggregate replacement in concrete to reduce global natural material depletion. Concrete usage is increasing rapidly; subsequently, the industry’s carbon footprint is increasing. Using CBA in the construction industry will reduce the technical and economic problems associated with power plants by reducing solid waste. This project aimed to determine if adding new sustainable materials, such as CBA, to concrete will reduce natural raw material usage, energy consumption, and greenhouse gas emissions while improving performance. This study included two projects: comparing increased CBA content to the two-control project and determining the optimum content based on the compressive strength. The optimum CBA content is 50%, which reduces fine aggregate usage in a concrete mix by 50% while maintaining equivalent or better concrete strength than a pure Portland concrete mix without CBA. The air content of the concrete mix containing % CBA decreased with increased CBA content and compressive strength, possibly due to the spacing factor of the voids in the mix and CBA’s porous and fineness behavior. The CBA optimum content had a unit weight lower than the controls for both projects, which makes the CBA mix a lightweight concrete. Using this material can significantly reduce natural material usage and environmental harm by reducing CBA waste disposal and improving concrete performance.

This paper shows the usage of a numerical analysis model which enables the calculation of the life of a railway wheels used for low-floor freight wagons as a function of its primary operating factors, which allows carrying out sensitivity analyses. Low-floor wagons are being increasingly used for combined transport applications and many types of bogies have been proposed in order to constitute the wagons. Due to the uniqueness of this type of wagons, the bogie configurations in terms of wheelbase and axle load have hardly been analyzed so far. The numerical analysis model used addresses the primary challenges that arise in the vehicle – track interaction and establish the relations among them. The main aspects of this model have been described in the paper, which has been later used to calculate the life of an ordinary-diameter wheel for several wheelbase and axle load values. This study has been replicated with reduced-diameter wheels, which are commonly used for low-floor wagons. In this way, it is possible to know the evolution of the life depending on the wheelbase and the axle load. The root causes underlying the observed behaviors can be explained by the entire understanding of the rolling phenomenon provided by the full analytical work.

This study was conducted in a laboratory-controlled environment aiming at studying the physical properties and elemental composition of coal combustion particles in a brazier. Particles were sampled ~1 m above the stove using a partector, where particles were collected on gold Transmission Electron Microscopy (TEM) grids and polycarbonate filters for TEM and inductively coupled plasma mass spectrometry (ICP-MS) analysis, respectively. Particles for elemental analysis collected on a 37 µm polycarbonate filters whereby a Gillian pump was used to draw in air. During sampling, a 2.5 µm cyclone was attached to the sampling cassette to isolate larger particles. The results have shown that combustion particles emitted during the early stage of combustion where single spherical particles with a diameter of around 450 nm. As the combustion progresses, the particle diameter gradually decreases and the morphology changes to accretion chain and fluffy bead structure for the flaming and char-burning phase, respectively.

The separation and enrichment can be targeted to enrich the rare and precious metals in fly ash and reduce the cost of leaching and recovering of fly ash. Regarding their different properties, the single-component separation was used to obtain uncompleted burned carbon, glass microbeads, minerals, and other characteristic components from the ash. Also, the mineral composition of each component was analyzed by electron microscopy. The metal minerals were mainly concentrated in the mineral components. Besides, the electron probe micro-analysis shows that the Pt content in the minerals of fly ash was significantly correlated with the metal contents of Ni and Cu. After the obtainment of the characteristics of fly ash metal enrichment, the heavy minerals with Cu, Ni, Pt, Pd, and other target metal elements were enriched by gravity separation and flotation. The enrichment coefficients of Cu, Ni, Pt, and Pd were 1.45, 1.33, 1.90 and 1.60, respectively, and the recovery rates were 77%, 81%, 97% and 88% respectively. Since the yield of heavy minerals obtained by separation was 62.24%, it indicated the physical separation method could significantly reduce the cost of leaching and recovering of fly ash metal resources.

Aiming to diminish the defects caused by high-speed pulsed GMAW welding, such as non-penetration, non-fusion, humping and undercut, the paper proposed an improved twin-wire double-pulsed high-speed welding process by introducing the impact of additional shielding gas on the welding pool and the effects of different shielding gas flowrates on the microstructure and mechanical properties of the welded seam was investigated. The 2205 duplex stainless steel plate was used as the base material for the butt welding test, and the welded seams were subjected to tensile test, metallographic analysis, hardness analysis, and nondestructive testing. The results indicate that as the flowrate of additional shielding gas increases in the range of 8 L/min~16 L/min, the width of the welded seam increases and the height of reinforcement decreases gradually. However, a grooved seam with a lower middle region and higher sides will appear when the gas flowrate becomes excessively large. The test results indicate that the jet impact force is relatively moderate when the flowrate of the additional shielding gas is 12 L/min and thus, is optimal for the welded seam.

With the continuous development of deep learning, the application of object detection based on deep neural network in the coal mine has been expanding. Simultaneously, as the production applications demand higher recognition accuracy, most research chooses to enlarge the depth and parameters of the network to improve accuracy. However, due to the limited computing resources in the coal mining face, it is challenging to meet the computation demands of a large number of hardware resources. Therefore, this paper proposes a lightweight object detection algorithm designed specifically for coal mining face, referred to as CM-YOLOv8. The algorithm introduces adaptive predefined anchor boxes tailored to the coal mining face dataset to enhance the detection performance of various targets. Simultaneously, a pruning method based on the L1 norm is designed, significantly compressing the model's computation and parameter volume without compromising accuracy. The proposed algorithm is validated on the coal mining dataset DsLMF+, achieving a compression rate of 40% on the model volume with less than a 1% drop in accuracy. Comparative analysis with other existing algorithms demonstrates its efficiency and practicality in coal mining scenarios. The experiments confirm that CM-YOLOv8 significantly reduces the model's computational requirements and volume while maintaining high accuracy.

This paper aims to investigate the coal thickness change area of the combined rock strata energy accumulation law. The method of connecting a uniaxial compression experiment with a theoret-ical analysis is used in this work. We employ a combination of coal and rock to carry out our studies. We investigate how different lithologies and ratios of coal-rock height affect the me-chanical properties of the mixture and the law governing energy accumulation. We have deter-mined the following facts: (1) The combination's peak strength and elastic modulus exceed that of coal and are inferior to that of rock but are nearer to that of coal. (2) When the coal-rock height ratios are dissimilar, the peak strength and modulus of elasticity of the combination show a negative correlation with the coal-thickness share, and the pre-peak energy accumulation and impact energy index of the combination shows a positive correlation with the coal-thickness share. (3) For the combination with the same coal-rock height ratio, the peak strength, elastic modulus, pre-peak energy accumulation, and impact energy index all increase with greater rock strength and elastic modulus. The presence of a hard rock layer affects the accumulation of pre-peak energy. ( 4 ) The stress in the surrounding rock gradually decreases as the coal thick-ness increases. In the area where coal thickness declines, the stress in surrounding rock is higher than that in the region where it thickens. The energy stored in the surrounding rock is directly proportional to the coal in the zone. Conversely, areas with thinner coal deposits exhibit a lower energy storage capacity in the surrounding rock than those with thicker coal deposits. The stress distribution of surrounding rock in coal thickness change is abnormal; substantial energy accu-mulation can swiftly initiate dynamic disasters, such as rock bursts. This study has important reference significance for preventing and controlling rock burst in coal thickness change areas.

As on 31.03.2020, 55.4 % (205135 MW) of total installed capacity (370106 MW) in India is through coal and lignite based power plants. These plants, set up by central, state and private utilities with substantial capital investment are facing consistently reducing Plant Utilization Factor (known as Plant Load Factor, PLF, in India). In the year 2019-20 the national average thermal power PLF stood at 55.4%, down from 78.6 % in 2007-08. On the other hand, the electricity demand is consistently rising in the country and there exists a peak and energy shortage at national level. In 2019-20 energy shortage was 0.7 % and peak shortage was 0.5 %. A disturbing paradox therefore exists here. On one hand, the country is power deficit, and on the other hand, a large amount of coal based affordable power, ready to be generated by thermal power generators, remains grossly unused. Looking into the fact that considerable investment has gone into developing these thermal power generation assets in the country, the falling PLF is a matter of concern for all the key stakeholders including the power producers, lenders, regulators and consumers. This paper identifies seven major factors that are affecting PLF of thermal power plants and then makes an attempt to project future scenario of PLF so that critical stakeholders can intervene through appropriate actions. Primary research with responses from power professionals has been used to find out the major factors. Future projection of PLF has been done using Partial Least Square (PLS) regression. Projection shows that in the Business As Usual case (Factors increasing at the current CAGR rate), the thermal power plants will face very low level of PLF (14.76 %) by 2024-25. This will mean that many plants will be shut down and many will run for only few hours in a day that too at very low loads. If the future generation mix is kept as indicated by Central Electricity Authority (CEA), a Govt. of India in its report (Draft report on optimal generation capacity mix for 2029-30- CEA- Govt of India) then the thermal power plant average PLF can sustain above 68 % until 2024-25. If followed, this path can be a breather for the thermal power plants.

This study aimed at characterizing the composition and performing chemical speciation modelling to determine species that are abundant in the coal fly ash (CFA) and soil samples sourced from Hendrina Power station located in Mpumalanga Province. All CFA samples were alkaline in nature with pH values ranging between 8.11 ± 0.07 and 8.60 ± 0.03 with an electrical conductivity (EC) ranging between 301.70 and 1515.00 µS/cm while EC of control soil was 103.10 µS/cm. The control soil pH was found to be 6.24 ± 0.13 and total organic carbon values ranged between 2.68 and 85.82 mg/kg and some percentage organic carbon values of CFAs were found to be greater than 8%, which is above the permissible limits of hazardous waste dumping. Oxidation-reduction potential values were negative in all CFA samples and positive in soil. The speciation modelling showed that the potential for a trace metal to have hazardous effects in soil systems depends on its concentration, specific form and interactions with other constituents in CFA. The slow release of metals from CFA to soil was assessed by looking at how a given metal is distributed throughout its several possible chemical forms. The presence of divalent cations (Pb2+, Cu2+, Zn2+, etc.) in CFAs might pose a threat to soil quality. In the competition for binding sites on ferric hydroxides, dissolved metal ions faced off against other metals. Protons (H+) were seen to be in competition with Pb, Cu and Zn for the ability to bind to hydroxyl (OH-) groups and this is due to chemical precipitation and surface complexation.

Abstract:Background: Foot ulcers, especially dorsal foot ulcers caused by straps in footwear, can lead to discomfort, pain, and severe complications, particularly in individuals with diabetes and leprosy. While plantar foot pressure measurements have been extensively studied, research on the impact of strap-induced pressure on the dorsal foot aspect remains limited.Research question: The main research question of this prospective study is: Does the implementation of a rolled inner seam strap design (RIS) in flip-flops result in reduced pressure at the toehold area compared to traditional strap designs (Control) in healthy volunteers?Methods: We studied healthy female volunteers, with 10 feet (5 left and 5 right) per arm of the study. Two types of flip-flops, RIS and Control, were compared in a standardized 5-step walk trial on a hardwood floor. Pressure at the toehold was measured using Pressure Sensitive Switches with portable, accurate, ultra-thin pressure sensors. Paired t-tests compared the maximum pressure at the toehold between RIS and Control flip-flops (p < 0.05).Results: The study revealed a statistically significant difference in pressure at the toehold between the RIS and Control flip-flops (p = 0.0014). The mean difference of -40.90 grams (95% CI: -61.22 to -20.58) indicated that the RIS exerted significantly lower pressure than the Control flip flops. The RIS group had a mean pressure of 29.30 grams. The Control group had a mean pressure of 70.20 grams at the toehold area.Significance: The findings of this study have significant clinical implications for individuals at risk of foot ulcers, particularly those with neuropathic conditions such as diabetes and leprosy. The implementation of the RIS design in flip-flops may offer a practical and cost-effective solution to reduce strap-induced pressure and mitigate the risk of strap-related foot ulcers, especially in resource-limited settings where comprehensive foot care is lacking.

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

: Kentucky is one of the largest coal producing states and surface coal mining has led to changes in natural land cover, soil loss, and water quality. This study explored relationships between actively mined and reclaimed areas and vegetation change and water quality parameters. The study site evaluated 58 watersheds with Landsat-derived variables (reclamation age, mining percentage, reclaimed forest percentage, and reclaimed woods percentage) as well as topographic variables (such as elevation, slope, drainage density, and infiltration). Water samples were collected in spring (n=9), summer (n=14), and fall (n=58) 2017 to study changes in water quality variables (SO42-, alkalinity, conductivity, Ca2+, Mg2+, Mn2+, Al3+, and Fe2+,Fe3+) in response to changes in land cover. Pearson correlation analyses indicated conductivity has strong to very strong relationships with other variables of water quality variables related to coal mining (except Al3+, Fe2+,Fe3+, Mn2+, elevation, slope, and drainage density) and land cover variables. In addition, separate multivariate regression analyses were performed with conductivity values based on samples collected in the fall. First, conductivity response to mining percentage, reclamation age and topographic variables were examined (adjusted R2=0.818, p &lt; 0.01). Next, vegetation cover change parameters were added to the same model, which yielded slightly improved R2 (adjusted R2 = 0.826, p &lt; 0.01). Finally, reclamation age and mining percentage were used to explain the quantity of reclaimed forested areas as a percentage of watersheds. The model was significant (p &lt; 0.01) with an adjusted R2 value of 0.641. Results suggest that the quantity (area as a percentage) of reclaimed forests may be a predictor of mining percentage and reclamation age. This study indicated that conductivity is a predictable water quality indicator that is highly associated with Coal Mine Related Stream Chemistry in areas where agriculture and urban development are limited. These findings may help the scientific community and key state and federal agencies improve their understanding of water quality attributes in watersheds affected by coal mining as well as refining land reclamation practices.

The recognition of coal-rock interface is very crucial for the research in the intelligent production of coal mine. This study investigates the application of terahertz time-domain spectroscopy in the recognition of coal-rock interface, including the identification of coal-rock and coal-rock mixtures, as well as the accurate characterization of coal seam thickness. Terahertz detection was used to obtain the optical parameter information of the pressed pellets prepared by mixing two different kinds of coal and two kinds of rock. Based on the experiment results, the database was established for the identification of coal-rock interfaces in coal mining machines. The terahertz detection was performed on 10 different kinds of sheet anthracite with different thickness, and the terahertz spectra of coal seams with different thickness were simulated and calculated by using simulation software, which can accurately obtain the thickness of coal seams and provide effective mining thickness parameters for coal seam mining. Through the experiment and simulation, the terahertz time-domain spectroscopy technology has a promising application prospect in the identification of coal-rock interface.

Swirling coal flames are encountered in swirl burners of boiler furnaces and cyclone coal combustors, and were studied using large-eddy simulation (LES) in reported references. However, the structures of swirling coal flames remain to be further studied. In the present paper LES of swirling coal flames is conducted for two combustors using two gas combustion models. The statistical simulation results are accessed by experiments and the instantaneous simulation results are used to analyze the specific features of flame structures of four cases. It is seen that different inlet flow conditions and different secondary-air flow rate lead to different flame structures

Coal is an important resource that is closely related to people’s lives and has an irreplaceable role. However, coal mine safety accidents occur from time to time in the process of working underground. To this end, this paper proposes a coal mine environmental safety early warning model to detect abnormalities and ensure worker safety in a timely manner by assessing the underground climate environment. In this paper, the support vector machine (SVM) parameters are optimized using an improved artificial hummingbird algorithm (IAHA), and its safety level is classified by combining various environmental parameters. To address the problems of insufficient global exploration capability and slow convergence of the artificial hummingbird algorithm during iterations, a strategy incorporating Tent chaos mapping and backward learning is used to initialize the population, a Levy flight strategy is introduced to improve the search capability during the guided foraging phase, and then the simplex method is introduced to replace the worst value before the end of each iteration of the algorithm. The IAHA-SVM safety warning model was established using the improved algorithm to classify and predict the safety of the coal mine environment into four classes. Finally, the performance of the IAHA algorithm and the IAHA-SVM model are simulated separately. The simulation results show that the convergence speed and the search accuracy of the IAHA algorithm are improved, and the performance of the IAHA-SVM model has a significant improvement.

To improve water injection effect, microemulsions (MEs) were used to wet coal seam compared with water and sodium dodecyl sulfate solution (SDS). Wetting effects were characterized by contact angle, X-ray diffraction, Fourier infrared spectroscopy. The results showed that the microemulsion has better spreadability on coal surface and has stronger wettability for coals of different ranks and different particle sizes than traditional wetting agents. The W/O type microemulsion is more affinity to coal than the O/W type and the bicontinuous type.Oxygen and hydrogen contents contributed to wetting. Different wetting agents have the greatest impact on the oxygen-containing functional group absorption zone of coal, but have little impact on the change of clay mineral composition.As the content of quartz increased, the content of montmorillonite was decreased, and the hydrophilicity of coal was increased. This research proposes new ideas for solving coal dust problems and reducing coal mine disasters.

Existing methods for detecting magnetic leakage signals from damaged wire ropes require axial saturation magnetisation, and the accuracy of the detection equipment depends on the saturation degree of magnetisation. Moreover, the expected magnetisation effect is usually difficult to achieve owing to the special characteristics of the rope structure, diameter, and operating environment of the wire rope. Consequently, in addition to other issues, the detection accuracy and versatility of the equipment are low. In this study, a method based on spatial multidimensional orthogonal array loop magnetisation for detecting mine wire rope defects is proposed. Firstly, a new sensor excitation structure model is developed. Then a method of radiant magnetic flux of permanent magnet array is analysed, and the influence law of the number of permanent radiant magnetic blocks on the magnetisation effect is studied. In addition, a method of wire rope detection based on the principle of clustering is investigated, according to which the influence law of the shape, structure, and size of the polyurethane device on the effect of magnetisation is discussed. Finally, through laboratory experiments, the test model and proposed method are verified. The results show that the magnetisation effect is better and more cost-effective when the number of permanent magnet radiation magnetic block is n=8, and the proposed detection method can effectively distinguish damaged wire rope joints. Furthermore, the proposed equipment achieved signal-to-noise ratio of the signals, improving the reliability of damage detection.

Residential coal combustion is one of the most significant sources of carbonaceous aerosols in the Highveld region of South Africa, significantly affecting the local and regional climate. In this study, we investigated single coal-burning particles emitted when using different fire-ignition techniques (top-lit up-draft vs bottom-lit up-draft) and air ventilation rates (defined by the number of air holes above and below the fire grate) in selected informal braziers. Aerosol samples were collected on nucleopore filters at the Sustainable Energy Technology and Research Centre Laboratory, University of Johannesburg. Individual particles (~700) were investigated using a scanning electron microscope equipped with energy-dispersive X-ray spectroscopy (EDS). Two distinct forms of spherical organic particles (SOPs) were identified, one less oxidized than the other. The particles were further classified into "electronically" dark and bright. EDS analysis showed that 70% of the dark spherical organic particles had higher (~60%) relative oxygen content than in the bright SOPs. We quantified the morphology of spherical organic particles and classified them into four categories: ~50% are bare single particles; ~35% particles are aggregated and form diffusion accretion chains; 10% have inclusions, and 5% are deformed due to impaction on filter material during sampling. We conclude that there are two distinct kinds of coal burning spherical organic particles and that dark SOPs are less volatile than bright SOPs. We also show that these spherical organic particles are similar in nature and characteristics to tar balls observed in biomass combustion and that they have the potential to absorb sunlight thereby affecting the earth’s radiative budget and climate. This study provides insights into the mixing states, morphology, and possible formation mechanisms of these organic particles from residential coal combustion in informal stoves.

The present work presents and discusses an analysis of the floor types of Villa of Diomedes (Pompeii archaeological park in the Campania region, Italy) both from architectural, archaeological, and structural point of view. In particular, the geometrical structural parameters of different floor types and the rules used by ancient builders to design them are investigated by means of interdisciplinary research. Link between structural-based assumptions, archival sources, geometric survey, in situ visual inspections and the archaeological information make it possible to define the geometrical structural parameters of eleven-barrel vaults, three wooden floors and three sloped wooden roofs (buried and collapsed during the Vesuvius eruption). A specific study of the barrel vaults is presented to investigate the relationships between the main vaults’ structural parameter. Furthermore, a comparison between the vaults’ dimensions obtained from surveys and those produced by the literature formulations from the 15th to the 20th centuries concerning masonry-vault designs is presented and discussed. These analyses carried out in the framework of Villa of Diomedes interdisciplinary project was very useful to interpret the fabrication of the Villa and to make a reconstruction of 3D model as it probably resulted to be the fateful year of 79 A.D.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

In this study, changes in the microstructure of coal tar pitch during successive processes, including pyrolysis, polycondensation, and crystallization, were examined in connection with the resulting variations in structure factors, as measured by XRD analysis, and functional groups, as confirmed by FTIR spectroscopy. To this end, four zones were defined based on variations in crystallinity, which were indicated by d002 and Lc. Each zone was further characterized by interpreting crystallinity development in relation to changes in functional groups and specimen height. At around 400 °C, polycondensation occurred as the C-Har and C-Hal peaks decreased in intensity. These peak reductions coincided with the formation of mesophase spheres, resulting in enhanced crystallinity. Subsequently, at around 500 °C, the peak intensity of C-H and COOH decreased, which was attributed to the release of large amounts of gasses. This led to sharp volume changes and a temporary reduction in crystallinity. All these results suggest that changes in the functional groups of coal tar pitch at lower temperatures (600 °C or less) during the carbonization process are closely associated with variations in its crystallinity. The major findings of the present study provide valuable insights for designing highly effective processes in the manufacturing of synthetic graphite blocks using CTP as a binder material, including by selecting appropriate temperature ranges to minimize volume expansion and crystallinity degradation and determining the lowest possible carbonization temperature to ensure adequate binder strength.

The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

In the extra-thick coal seams and multi-layered hard roofs, the longwall hydraulic support yielding, coal face spalling, strong deformations of goaf-side entry, and severe ground pressure dynamic events typically occur at the longwall top coal caving longwall faces. Based on the Key strata theory an overburden caving model is proposed here to predict the multilayered hard strata behaviour. The proposed model together with the measured stress changes in coal seam and underground observations in Tongxin coal mine provides a new idea to analyse stress changes in coal and help to minimise rock bursts in the multi-layered hard rock ground. Using the proposed primary Key and the sub-Key strata units the model predicts the formation and instability of the overlying strata that leads to abrupt dynamic changes to the surrounding rock stress. The data obtained from the vertical stress monitoring in the 38 m wide coal pillar located adjacent to the longwall face indicates that the Key strata layers have a significant influence on ground behaviour. Sudden dynamically driven unloading of strata was caused by the first caving of the sub-Key strata while reloading of the vertical stress occurred when the goaf overhang of the sub-Key strata failed. Based on this findings several measures were recommended to minimise the undesirable dynamic occurrences including pre-split of the hard Key strata by blasting and using the energy consumption yielding reinforcement to support the damage prone gate road areas. Use of the numerical modelling simulations was suggested to improve the key theory accuracy.

The aim of this study was to evaluate implants survival rate, marginal bone loss, surgical and prosthetic complications of implants placed through sinus floor elevation and tilted implants en-gaged in basal bone in order to bypass maxillary sinus. 60 patients were enrolled for this study. According with residual bone height of posterior maxilla the sample was divided in three groups of 20 patients: Group A (lateral sinus floor elevation), Group B (transrectal sinus floor elevation) and Group C (tilted implants employed to bypass sinus floor). Follow-up visits were performed one week after surgery, at 3, 6 months and then once a year for next 4 years. The outcomes were implants survival rate, marginal bone loss and surgical and prosthetic complications. Although the Group A, B and C have demonstrated an implants survival rate of 83.3%, 86,7% and 98,3% respectively, the statistically analysis showed that there was no statistically significant difference between groups. Statistically significant differences between the groups were also not found con-cerning marginal bone loss, as recorded by intra-oral X-ray measurements during follow-up. About complications it wasn’t possible to perform a statistical analysis. To as to reduce potential surgical risks implants placement in basal bone should be preferred.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

Mercury emissions from small-scale coal-fired boilers are still a serious environmental problem in Poland and the Czech Republic. The publication presents the results of mercury emission tests conducted using five different small-scale coal-fired boilers and five different coal fuels. The research was carried out under laboratory conditions, but also using residential users' heating devices. They covered a wide range of operational parameters, both energy and emission. It was shown that more than 94% of the mercury contained in coal fuel undergoing combustion is emitted into the atmosphere with the volatile products of combustion (including dust), and the amount of emissions is strongly dependent on the original mercury content of the fuel. One solution to the problem of mercury emissions from small-scale coal-fired boilers may be to replace traditional coal with low-emission carbon fuels. The paper shows that mercury emissions from burning such fuels are many times lower than from burning coal. The widespread use of low-emission carbon fuels in individual heating systems in Poland and the Czech Republic would reduce mercury emissions to the atmosphere by up to 90% compared to the current level of emissions generated by individual heating systems in these countries.

This study is aimed to explore the environmental risk posed by the unsustainable mining activities in Mulawarman village, East Kalimantan, and articulate the disproportionate impact from the perspective of environmental justice on how mining regulations affect the lives of a vulnerable community. A qualitative comparative analysis based on the legislation and administrative rules on coal mining, and a case study of Mulawarman village were adopted. The information was framed based (participatory) observation, and in-depth interview, and purposively conducted to six selected respondents. The result shows how the laws and regulations disadvantage the community and expose them to unequal treatment. The adverse effects of mining activities change the socio-environmental dynamics in this village. Being the breadbasket in 1997, Mulawarman villagers experience the loss of food self-sufficiency, and turn to the government and mining company for social welfare, and clean water. Also, inconsistent and incomplete regulations pertaining to mining, favor to serve the business interests before the environment and the local community. This results in severe encroachment upon community rights and leads to long-term conflicts between mining companies and local communities, and has weakened the capacity of local authorities to help the affected community to recover their rights.

In order to reduce the environmental damage caused by coal waste landfills, it is necessary to look for rational ways of their management. One of the methods of their development may be the creation of soil-like substrates. The aim of the study was to assess the properties of soil-like substrates from coal mining waste with a varied share of sewage sludge and waste mineral wool. The evaluation of the properties of the substrates was carried out in a pot experiment. The properties of the substrates and their yield potential were determined. Coal mining waste as a substrate, compared to anthropogenic soil, was characterized by: significantly higher sorption capacity, content of alkaline cations and pH, significantly higher content of organic carbon, nitrogen and assimilable forms of K and Mg, and lower content of assimilable P. The substrates enriched with sewage sludge showed: significant increase in the content of organic carbon, nitrogen and assimilable forms of P and Mg, optimization of sorption properties. Extending the composition of substrates with mineral wool resulted in further improvement of their properties. Yields of plants grown on coal mining waste were significantly lower than on anthropogenic soil. Substrates with sewage sludge and mineral wool had a significantly higher yield potential.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

We studied the influence of lava meal, zeolite and top layer of sandy soil as bedding additives on gaseous C and N losses from a sloping-floor barn of naturally ventilated animal housing. We selected four barn units where eight young bulls’ group was reared in each barn. Chopped straw of wheat and barley applied daily at the rate of 5 kg per livestock unit (LU) in bedding areas where one LU consisted of 500 kg body mass of live bulls. Zeolite, lava meal and sandy soil (18% clay + silt) applied in barn at the rate of 10, 20 and 30% of straw dose, respectively. Static flux chamber was used to measure gases emissions from the barn unit and mass balance calculation was used to calculate straw manure total N (TN) losses during housing phase. On an average, all bedding additives decreased 85% of the NH₃ emission compared to control; however, they did not influence CH₄ emission. Zeolite decreased CO₂ (35%) and N₂O (37%) emission rates. Subsequently, lava meal, sandy soil and zeolite decreased 23, 37, and 50% of TN losses from barn manure, respectively. Overall, measured N emissions through NH₃-N and N₂O-N from the barns was 11% of calculated TN losses while remainder 89% was most probably attributed to di-nitrogen (N₂), a harmless gas. Hence, in straw-based cattle housings, zeolite could be a promising additive for reduction of CO₂, N₂O and NH₃ emissions and sandy soil can be considered as cheap and readily available resource for reducing NH₃ emission.

Generating electricity from coal combustion is highly associated with ongoing pollution problems that negatively impact the environment. Coal fly ash (CFA) is a predominant waste by-product of coal combustion which is disposed of in exposed ash dams constructed in the vicinity of power stations. Its disposal requires a large piece of land and therefore more land is converted to unproductive disposal sites, degrading the ecosystem. This waste material is classified as a hazardous substance in South Africa due to unacceptable levels of inorganic and persistent organic pollutants and its potential for dust creation. CFA is recycled and sold to the building and construction sectors, but the rate of its utilization is far less than the production rate resulting to high volumes that is stockpiled in disposal sites. More than 500 million tons CFA is produced yearly and over 200 million tons yearly remain unused globally and more CFA will continue to be produced due to high consumer energy demands, especially in countries with heavy reliance on coal for power generation. In this context, the paper discusses production of CFA, pollution problems due to its disposal, examines existing gaps within the scope of ash dam restoration processes and presents opportunities offered by phytoremediation (a low-cost and environmentally friendly technology that utilizes plants to restore the degraded environments). Ecological restoration through the use of socio-economically valuable plants (aromatic plants, legumes and grasses) has potential in addressing societal challenges and consequently impacting positively the livelihood of communities.

Involving industrial waste into economic circulation, in particular flotation waste from coal enrichment, is an urgent task. The coal preparation waste of ArcelorMittal Temirtau JSC was studied with a view to the possibility of using it as an alternative substitute for coke breeze in the sintering process. During a thermoanalytical study on a synchronous thermal analyzer STA 449 NETZSCH in dynamic mode with a heating rate of 10, 20, 30 °C/min in an air flow of 30 cm³/min in the temperature range 30–1000 °C, we determined the lower heat of combustion of carbon-containing material, change mass during calcination, change and rate of change in the mass of the sample, thermal effect of the process, the temperature of the beginning, end and maximum development of thermal effects. It has been established that the greatest mass loss is observed in the temperature range 580 °C- 610 °C, which is about 65–67% of the total mass of the organic component of coal. The maximum burnout rate corresponds to a temperature of 540–563 °C. The lowest calorific value of the studied waste was 15.9 MJ/kg. The results of thermal analytical research and technical analysis substantiate the possibility of using flotation waste in a mixture of up to 10% with coke breeze for combustion in the sintering layer for the production of sinter. Analysis of the composition of flotation waste showed that they have a high specific surface area (56.8∙10³ m²/kg), are highly dispersible, soggy, and capable of swelling, and the predominant amount of clay substance makes them a plastic material. The possibilities of using coal flotation waste as an alternative substitute for coke breeze have been studied after the regimes of its preparation for sintering have been developed and a rational regime of layer-by-layer combustion in the sintering layer has been established. The optimal ratio of coke and OPC in the fuel mixture of the sintering charge was determined.

A D-grade type coal was burned under simulated domestic practices in a controlled laboratory set-up, in order to characterize emissions of volatile organic compounds (VOCs); viz. benzene, toluene, ethylbenzene and xylenes (BTEX). Near-field concentrations were collected in a shack-like structure constructed using corrugated iron, simulating a traditional house found in informal settlements in South Africa. Measurements were carried out using the Synspec Spectras GC955 real-time monitor over a three-hour burn cycle. The 3-hour average concentrations (in µg/m³) of benzene, toluene, ethylbenzene, p-xylene and o-xylene were 919 ± 44, 2051 ± 91, 3838 ±19, 4245 41 and 3576 ± 49, respectively. The cancer risk for adult males and females in a typical SA household exposure scenario, was found to be 1.1 -1.2 and 110-120 folds higher than the US EPA designated risk severity indicator (1E^-6), respectively. All four TEX compounds recorded the Hazard Quotient (HQ) of less than 1, indicating a low risk of developing related non-carcinogenic health effects. The HQ for TEX ranged from 0.001– 0.05, with toluene concentrations being the lowest and ethylbenzene the highest. This study has demonstrated that domestic coal burning may be a significant source of BTEX emission exposure.

This study reveals the essential load-bearing characteristics of the steel-concrete composite floor system under fire conditions applying structural stressing state theory. Firstly, the strain data in the entire process of the fire test are modeled as state variables which can present the slab’s stressing state evolution characteristics; Then, the state variables are used to build the stressing state mode and the parameter characterizing the mode. Further, the Mann-Kendall criterion is adopted to detect the leap points in the evolution curves of the characteristic parameters during the entire fire exposure process. Also, the evolution curves of the stressing state modes are investigated to verify the leap profiles around the leap/characteristic points; Finally, the detected leap points are defined as the failure starting points and elastoplastic branching points, which is unseen in the past researches focusing on the failure endpoint defined at the ultimate load-bearing state of the composite floor system. The failure starting point and the elastoplastic branching point are the embodiment of natural law from quantitative change to quality change of a system rather than an empirical and statistical judgment. Hence, both characteristic points avoidably exist in the strain data of the composite floor system undergoing the fire process, which can be revealed through the proper modeling methods and update the existing theories and methods on structural analysis and design in fire.

Purpose: The aim of the present experimental 3D-finite element study was to evaluate the influence of an augmented sinus lift with an additional inserted bone graft block. The bone graft block stabilizes the implant in addition to conventional augmented bone. We placed the block in three different positions. The implants were loaded with axial force and forces secondary to laterotrusion and protrusion. Material and Methods: A simplified U-shaped 3D finite element model of the upper jaw and a more complex anatomical model of the left maxilla were created. The bone graft block was placed in three positions: in the lower third in contact with the sinus floor, the middle, and the upper third of the implant. Van Mises’ stress distribution was calculated and analyzed for the different models. We also compared the complex anatomical model with the simplified one. Results: The position of the bone graft block significantly influences the magnitude of stress distribution. A bone graft block positioned in the upper third or middle of the implant reduces the quantity of stress compared to the reference model without a bone graft block. The low bone graft block position is clearly associated with lower stress distribution in compact bone. We registered no significant differences in stress in compact bone with regard to laterotrusion or protrusion. Conclusions: Maximum values of von Mises stresses in compact bone can be reduced significantly by using a bone graft block. The reduction of stress is nearly the same for positions in the upper third and the middle of the implant. It is much more pronounced when the bone graft block is in the lower third of the implant near the sinus floor, which appeared to be the best position in the present study.

CO2 geological sequestration in coal seams can achieve the dual objectives of CO2 emission reduction and enhanced coalbed methane production, making it a highly promising carbon capture and storage technology. However, the injection of CO2 into coal reservoirs in the form of supercritical fluid (ScCO2) leads to complex physicochemical reactions with the coal seam, altering the properties of the coal reservoir and impacting the effectiveness of CO2 sequestration and methane production enhancement.In this paper, theoretical calculations based on ReaxFF-MD were conducted to study the interaction mechanism between ScCO2 and the macromolecular structure of both low-rank and high-rank coal, to address the limitations of experimental methods. The reaction of ScCO2 with low-rank coal and high-rank coal exhibits significant differences. At swelling stage, the low-rank coal experiences a decrease in aromatic structure and aliphatic structure, high-rank coal shows an increase in aromatic structure and a decrease in aliphatic structure, while swelling phenomenon is more pronounced in high-rank coal. At dissolution stage, low-rank coal is initially decomposed into two secondary molecular fragments, and then recombine to form new molecular structure, the aromatic structure increased and the aliphatic structure decreased. In contrast, high-rank coal occurs stretches-breakage-movement-reconnection, a reduction in aromatic structure and an increase in aliphatic structure.The primary reasons for these variations lie in distinct molecular structure compositions and the properties of ScCO2, leading to different reaction pathways of functional group and aromatic structure. The reaction pathways of functional groups and aromatic structures in coal can be summarized as follows: the breakage of the O-H bond in hydroxyl groups, the breakage of the C-OH bond in carboxyl groups, transformation of aliphatic structures into smaller hydrocarbon compounds or formation of long-chain alkenes, and various pathways involving broken, rearrangement, recombination of aromatic structures. In low-rank coal, there is a higher abundance of oxygen-containing functional groups and aliphatic structures. The breakage of O-H and C-OH chemical bonds results in the formation of free radical ions, while some aliphatic structures detach to produce hydrocarbons. Additionally, some of these aliphatic structures combine with carbonyl groups and free radical ions to generate new aromatic structures. Conversely, in high-rank coal, the lower content of oxygen-containing functional groups and aliphatic structures, along with stronger intramolecular forces, results in fewer chemical bond breakages and makes it less conducive to the formation of new aromatic structures.These results elucidate the specific deformations of different chemical groups, offering a molecular-level understanding of the interaction between CO2 and coal.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

Increased attention has been paid to the influence of coal mining subsidence on ecological environment. Restoration of ecosystem in damaged mining area is critical for restoring disturbed environment. The comparing of plant communities and microbial communities in the artificial restoration and natural restoration areas provides an effective method for evaluating the restoration effects. However, such studies are limited in coal mining subsidence restoration areas. Subsidence area in Shendong mining area, located in the semi-arid region of Western China, was restored from 2003 with 5 ecological restoration plant species. In July 2017, the comparison and analysis of plant and microbial communities were conducted at the artificial restoration areas (AR) and the natural remediation areas (NR). The results showed that the artificial ecological restoration in Shendong mining area has achieved some success, but it has not recovered to a similar ecosystem before the destruction. A higher plant species, coverage and bacterial community diversity were observed in AR. However, these features have lower similarity compared with those in NR sites. Potential soil factors, such as pH, moisture content, total carbon content, organic matter, nitrogen and bulk density, have a greater impact on soil bacterial community structure and diversity. In the ecological restoration of the mining area, attention should be paid to the restoration of soil properties in the mining area. This study can provide theoretical guidance for more scientific ecological restoration in the damaged mining area.

The study aimed to evaluate implant success and bone height variations after transcrestal sinus floor elevation (tSFE) using the osseodensification technique (OD) combined with beta-tricalcium phosphate (β-TCP), as bone graft material and simultaneous implant placement. Thirteen patients requiring the placement of one implant in the upper posterior maxilla, with a residual bone height of

Abstract A variety of surgical techniques have been developed to reconstruct the posterior maxilla when bone volume is insufficient. A barrier membrane or bone window pushed inside the sinus cavity as the ‘‘roof’’ of the sinus cavity for preserve the space and help bone. The heterologous cortical lamina is used for the mechanical support, without any grafting material, of sinus membranes resulting in only bone tissue formation and not mixed with the graft.

Background: Post-operative pain and swelling are frequently observed after sinus lift procedures. The aim of the present study was a clinical evaluation of swelling and pain of two sinus lift different flaps technique measured through visual analogue scale (VAS), verbal rating scale (VRS) and infrared thermal imaging (i.e., thermography). Methods: A randomized controlled trial was conducted in fifteen patients treated for a total of 30 sinus randomly allotted into two groups. In patients of Group I, a triangular flap was performed, while in Group II modified triangular flap without anterior release was performed. Postoperative pain was scored by VAS and inflammation was recorded by VRS at 2, 4, 6 and 14 days. The facial temperature was recorded before and after sinus augmentation, at 2, 4, 6 day intervals for the first week and at 14 day, to check the course of healing. Results: In group I the pain intensity was recorded at 2 days after the surgery with a score of 38.67 ± 6.4 mm. Swelling was higher at 2 and 4 day, and it was absent at day 6. Facial temperature difference before and after the procedure was 3 (4.737 °C ± 0.37). In Group II the pain was lower than in Group I (p < 0,05). Swelling scored 2 on the first and second day, and it was reduced at day 4. After the second day the difference of temperature reduced significantly compared to day of surgery (0.77 °C), at 2 and 4 days no difference was registered. Conclusion: In conclusion based on the outcome of the present study, modified triangular flap can be used with success in sinus augmentation procedures and is to be preferred to trapezoidal flap.

Background. ADHD is a neurodevelopmental disorder that is accompanied by executive deficits. Objectives. To obtain evidence of the usefulness of the BRIEF-P and to analyse the possible ceiling and floor effect of its scores in the assessment of executive function in preschoolers with signs compatible with a possible diagnosis of ADHD. Methods. Seven articles were selected from 2538 potentially eligible articles from different databases. We included studies assessing samples of individuals with symptoms compatible with ADHD, with age range 2-6 years, published in English or Spanish, during the period 2012-2022. References published in: Science Direct, NCBI (PubMed), ProQuest Education Journals in the last decade. Risk of bias was assessed using the QUADAS-2 questionnaire. The main variables were: age and executive functioning. Conclusions. Executive deficits in early-life individuals with ADHD-compatible symptoms are more extensive than deficits in working memory. BRIEF-P is an instrument that facilitates obtaining a sensitive and discriminative executive profile. It should be used in combination with other neuropsychological performance tests, finding a floor effect in tests associated with warm executive functions and a ceiling effect in cold executive functions. This requires using a variety of tests to assess executive performance in preschoolers with symptoms compatible with ADHD and designing intervention proposals in line with them...

Non-impregnated small pore graphite (NSPG) with the compact microstructure for using in molten salt reactors (MSR) was prepared by the novel process, and the pore diameter of the obtained graphite was reduced to ~800 nm. The irradiation evaluation of the prepared graphite was carried out by 7 MeV Xe26+ ion irradiation and the microstructural changes of the graphite were investigated with IG-110 as a comparison. The graphitization degree of NSPG was higher than that of IG-110, though it was not subjected to an impregnation process. Under low-dose ion irradiation (

Railway transportation is one of the main modes of long-distance coal transportation, and it is inevitable to cause environmental pollution during the transportation process. In order to improve the environment along the railway and increase the utilization rate of coal resources, this paper proposes a detection algorithm for scattered coal solidification layer during transportation based on the YOLO v8 model, and designs an intelligent recognition model suitable for coal solidification layer detection devices by combining fluorescence detection methods. Through experimental analysis, the model meets the requirements of practical detection and plays a crucial role in environmental protection, with strong practical application value.