A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

Quantifying the landscape pattern change can effectively demonstrate the ecological progresses and the consequences of urbanization. Based on remotely sensed land cover data in 1994, 2000, 2006 and a gradient analysis with landscape metrics at landscape- and class- level, we attempted to characterize the individual and entire landscape patterns of Shanghai metropolitan during the rapid urbanization. We highlighted that a roadscape transect approach that combined the buffer zone method and the transect-based approach was introduced to describe the urban-rural patterns of agricultural, residential, green, industrial, and public facilities land along the railway route. Our results of landscape metrics showed significant spatiotemporal patterns and gradient variations along the transect. The urban growth pattern in two time spans conform to the hypothesis for diffusion–coalescence processes, implying that the railway is adaptive as a gradient element to analyze the landscape patterns with urbanization. As the natural landscape was replaced by urban landscape gradually, the urban fringe expanded radically. The results also showed that the desakota region expanded its extent widely. Satellite towns witnessed the continual transformation from the predominantly rural landscape to peri-urban landscape. Furthermore, the gap between urban and rural areas remained large especially in public service. More reasonable urban plans and land use policies should push to make more of an effort to transition from the urban-rural separation to coordinated urban-rural development. This study is a meaningful trial in demonstrating a new form of urban–rural transects to study the landscape change of large cities from a strategic viewpoint. By combining gradient analysis with landscape metrics, we addressed the process of urbanization both spatially and temporally, and provided a more quantitative approach to urban studies.

Porous α-Al2O3 ceramics is a highly demanded material for multitude applications such as filters, substrates, biomedicine materials, etc. Despite the availability of the raw materials, a challenge of their technology is in a high energy budget caused by the sintering above 1500 °C. For a cold sintering processing (CSP) of ceramics, the lowering of α-Al2O3 sintering temperature is one of the most urgent challenges at the background of its rapid development. The current paper for the first time demonstrates the solution of the mentioned problem by the CSP of α-alumina ceramics in a presence of pure water as a transient liquid. The manufactured materials were examined by XRD analysis; the evolution of their microstructures during the CSP was revealed by SEM, and the porosity evaluated by the Archimedes method. The ceramics with an open porosity up to 36 % was produced at 380-450 °C, 220 MPa in 30 min. An increase in the pressure was found to impede α-Al2O3 formation from γ-AlOOH. The development of the microstructure was discussed within the frameworks of the dissolution-precipitation model and the homogenous nucleation. The results of the SEM study pointed to the coalescence of γ-AlOOH grains during the CSP.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

Municipal solid waste incineration fly ash (MSWI FA) predominantly consists of compounds comprising elements such as calcium, aluminum, silicon, sodium, and others. Additionally, it encompasses a complex mixture of heavy metals, chlorides, sulfates, organic pollutants, and other constituents. The effective and economically viable treatment of MSWI FA poses a formidable challenge for the current stage of resource cycling. In this research report, we will adopt a novel low-temperature sintering method called "Cold Sintering Process" (CSP) as a means to immobilize heavy metals within the fly ash. By utilizing a Taguchi orthogonal array, we will adjust five control factors in the CSP, including sintering temperature, uniaxial pressure, sintering time, initial water addition, and sodium carbonate dosage. The leaching of cadmium element from the fly ash, as measured by TCLP, will serve as the quality indicator. Through the application of CSP, the MSWI FA will be transformed into structurally stable ceramic blocks, effectively immobilizing the heavy metals within the blocks. The results of the experiments showed that MSWI FA under the conditions of a temperature of 300℃, uniaxial pressure of 312 MPa, sintering time in 60 minutes, 25 wt% water addition, and 9 wt% Na2CO3 addition could effectively reduce the leaching of cadmium by 77.71%, lead by 21.14%, zinc by 42.37%, and chromium by 99.99%, as compared to the original MSWI FA TCLP results.

The interest in the Spark Plasma Sintering (SPS) technique has continuously increased over the last few years. This article shows the possibility of the development of a SPS device used for material processing and synthesis both in both scientific and industrial applications. This work presents an example of processing Arc-Meleted (half-Heusler, cobalt triantimonide) and SHS-synthesized semiconductors (bismuth telluride) materials with SPS device. The system functionalities expansion is presented, showing the possible way of increasing the information amount obtained about SPS processes and using the SPS apparatus for conducting synthesis of materials and increasing reproducibility and accuracy of process parameters control.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

Nanopowders are continuously under investigation as they open new perspectives in numerous fields. There are two main challenges to stimulate their development: sufficient low-cost high throughput synthesis methods leading to a production with well-defined and reproducible properties, and for ceramics, conservation of their nanostructure after sintering. In this context, this paper presents the synthesis of a pure nanosized powder of ZnO (dv₅₀ ~ 60 nm, easily redispersable) by using a continuous Segmented Flow Tubular Reactor (SFTR), which has previously shown its versatility and its robustness, ensuring a high powder quality and reproducibility over time. A higher scale of production can be achieved based on a “scale-out” concept by replicating the tubular reactors. The sinterability of ZnO nanopowders synthesized by the SFTR was studied, by natural sintering at 900 °C and 1100 °C, and Spark Plasma Sintering (SPS) at 900 °C. The performances of the synthesized nanopowder were compared to a commercial ZnO nanopowder of high quality. The samples obtained from the synthesized nanopowder could not be densified at low temperature by traditional sintering, whereas SPS led to a fully dense material after only 5 minutes at 900 °C, while limiting the grain growth and thus leading to a nanostructured material.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

We present new results in positron annihilation lifetime spectroscopy (PALS), thermo-optical dilatometry and microscopy, which are indicating a strong correlation between grain-boundaries and mass transport during the sintering process of carbonyl iron powder. In this particular system we were able to show that the change in particle shape and size with increasing temperature yields an anisotropy in shrinkage, which manifests itself in a higher shrinkage perpendicular to the compaction axis. In the intermediate stage of sintering, where the major mass transport occurs, the average distance between two grain boundaries could be determined to (3,73 ± 0,18) μm at T = 744°C. This is in good agreement with previous calculations of positron pathways in defect free particles. Furthermore, due to sintering temperatures far above the annealing temperature of dislocations in iron, the existence of dislocations in the bulk of the particles is very unlikely. These claims are reflected by the collected positron data, which exhibit a clear grain boundary signal of ∼ 250ps while no vacancy or dislocation signal (typically ∼ 160 ps) is evident in the intermediate stage of sintering.

Thermoelectric materials may be used in devices as thermoelectric “air conditioner” in a smart house for improved energy efficiency. Energy harvesting uses ambient energy to generate electricity. It provides potentially low-cost, maintenance-free, long-life equipment by reducing the need for batteries or power chords. Energy harvesting (EH) is also known as power harvesting or energy scavenging. EH is considered to give benefits related to environmental friendliness, safety, security, convenience and affordability. EH can be used for brand enhancing. Technically, it can be used to make new things possible depending on visionary engineering. The variety of thermoelectric (TE) materials that can be used in energy harvesting is quite large, and the optimal material for a given application depends mainly on the temperature range in which the material is to be used. In this work we study the development and characterization of thermoelectric materials which were prepared by two different method, which were: a) ball-milling followed by sintering and b) ball-milling, microwave synthesis, high energy planetary ball milling, and sintering. Finally, we study the thermoelectric properties, calculate the band gaps and the ZT for the thermoelectric materials.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

Bacteria can colonize and develop biofilm on a large variety of biotic and abiotic materials, it is accountable for nosocomial infections and chronic illness and consequently, it is a serious economic and public health problem. Staphylococcus epidermidis, thanks to its ability to form biofilm and colonize biomaterials, represents the most frequent causative agent involved in bio-film-associated infections of medical devices. Due to the biofilm presence, S. epidermidis infections are extremely difficult to treat and the research of new molecules able to interfere with its biofilm formation has a remarkable interest. In the present work, the attention was focused on Pseudomonas sp. TAE6080, an Antarctic marine bacterium able to produce and secrete an effective antibiofilm compound. The molecule responsible for this activity was purified by an activity-guided approach and it resulted to be a periplasmic protein, named Cold-Azurin. The Cold-Azurin was recombinantly produced in E. coli and purified. The recombinant protein was able to impair S. epidermidis attachment to the polystyrene surface and effectively prevent biofilm formation.

In this paper, the preparation methods of porous silicon nitride materials with controllable dielectric constant and pore structure were systematically studied. By using microwave sintering technology, porous silicon nitride materials with high closed pore ratio were prepared by adjusting the content of sintering additives and sintering process parameters, and controlling the grain boundary phase and pore structure and size. The effects of sintering conditions on the total porosity, closed porosity, pore structure and dielectric properties of materials were systematically studied.

Selective laser sintering (SLS) has drawn attention for the fabrication of three-dimensional oral dosage forms due to the plurality of drug formulations that can be processed. The aim of this work was to employ SLS with a CO2 laser for the manufacturing of carvedilol personalised dos-age forms of various strengths. Carvedilol (CVD) and vinylpyrrolidone-vinyl acetate copolymer (Kollidon VA64) blends of various ratios were sintered to produce CVD tablets of 3.125, 6.25 and 12.5 mg. The tuning of the SLS processing parameter laser intensity, improved printability and impacted the tablet hardness, friability, CVD dissolution rate, and the total amount of drug re-leased. Physicochemical characterization showed the presence of CVD in the amorphous state. X-ray micro-CT analysis demonstrated that the applied CO2 intensity affected the total tablet po-rosity, which was reduced with increased laser intensity. The study demonstrated that SLS is a suitable technology for the development of personalised medicines that meet the required specifications and patient needs.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

The concept of using special electrical circuit design realize a "cold resistors", that is, an active resistor circuitry with lowered effective noise temperature, was first introduced about 80 years ago. Later on, various kinds of artificial resistors were applied in different research areas, such as gravitational wave detection, photo-amplifiers and quartz oscillators. Their proofs of concepts were experimentally proved. Unfortunately, the complete theory was not found even though several attempts had been published, sometimes with errors. In this paper, we describe a correct and complete circuit theoretical model of a cold resistor system. The results are confirmed by computer simulations. A design tools for this circuit is also shown.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Due to the high specific surface area of titanium aluminide powders, significant and unavoidable surface oxidation takes place during processing. The resulting oxides disrupt the conventional powder metallurgical process route (pressing and sintering) by reducing green strength and sintered properties. Oxide-free particle surfaces offer the potential to significantly increase particle bond strength and enable the processing of difficult-to-press material powders. In this work, the effect of milling titanium aluminide powder in a silane-doped atmosphere on the component properties after pressing and subsequent sintering was investigated. Ball milling was used to break up the oxide layers and create bare metal surfaces on the particles. With the help of silane-doped inert gas, the oxygen partial pressure was greatly reduced during machining. It was investigated whether oxide-free surfaces could be produced and maintained by milling in silane-doped at-mospheres. Furthermore, the resulting material properties after pressing and sintering were an-alyzed using density measurements, hardness tests, EDX-measurements and micrographs. It was concluded, that ball milling in a silane-doped atmosphere produces and maintains oxide-free particle surfaces. These oxide-free surfaces and smaller particle sizes improve the component properties after pressing and sintering.

In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.

In order to produce nanostructured Ti0.9Cr0.1C powders, an elemental powder mixture of titanium, chromium, and graphite is milled in this work using a high-energy ball mill for various milling times. Microstructural characteristics such as crystallite size, microstrain, lattice parameter, and dislocation density are determined using X-ray diffraction (XRD). Mechanical alloying successfully produced nanocrystalline (Ti,Cr)C with an average crystallite size of 11 nm. This size of the crystallites is also directly verified using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used to investigate the morphology of the samples. The novelty of this work is advancing the scientific understanding of the effect of milling time on the particle size distribution and crystalline structure, and also understanding the effect of the spark plasma sintering on the different properties of the bulks. Densified cermet samples were produced from the nanocrystalline powders, milled for 5, 10 and 20 hours by SPS process at 1800 degrees for 5 min under a pressure of 80 MPa. Phase changes of the produced cermets were examined according to XRD, SEM/EDX analyses. Significant amounts of Cr and Fe elements were detected, especially in the 20 h milled cermet. The bulk forms of the milled powders for 5 and 20 h had a relative density of 98.43 and 98.51 %, respectively. However, 5 h milled cermet had 93.3 HRA because of the more homogeneous distribution of the (Ti,Cr)C phase, the low iron content and high relative density. According to the 0.0011 mm/year corrosion rate, and 371.68 kΩ*cm2 charge transfer resistance obtained from the potentiodynamic polarization and EIS tests, the 20 h cermet was the specimen with the highest corrosion resistance.

Speckle Plethysmography (SPG) and Photoplethysmography (PPG) are different biophotonics technologies that allow for measurement of hemodynamics. As the difference between SPG and PPG under low perfusion conditions is not fully understood, a Cold Pressor Test (CPT) was used to modulate blood pressure and peripheral circulation. A custom-built setup simultaneously derived SPG and PPG from the same video streams at two wavelengths (639 nm and 850 nm). SPG and PPG were measured at right index finger location before and during CPT using finger Arterial Pressure (fiAP) as reference. The effect of CPT on Alternating Component amplitude (AC) and Signal-to-Noise-Ratio (SNR) of dual-wavelength SPG and PPG signals was analysed across participants. Furthermore, waveform differences between SPG, PPG, and fiAP based on frequency harmonic ratios, were analysed for each subject (n=10). Both PPG and SPG at 850 nm show a significant reduction during CPT for both AC and SNR. However, SPG showed significantly higher and more stable SNR than PPG in both study phases. Harmonic ratios were found substantially higher in SPG than PPG. Therefore, in low perfusion conditions, SPG seems to offer a more robust pulse wave monitoring with higher harmonic ratios than PPG.

Autoimmune hemolytic anemia is a rare condition characterized by destruction of red blood cells with and without involvement of complement. It is associated with significant morbidity and mortality. In warm autoimmune hemolytic anemia less than 50% of patients remain in a long-term remission following initial steroid therapy and subsequent therapies are required. Cold agglutinin disease is a clonal hematologic disorder which requires therapy in majority of patients and responds poorly to steroids and alkylators. Rituximab has a favorable toxicity profile and has demonstrated efficacy in autoimmune hemolytic anemia in first line as well as relapsed setting. Rituximab is the preferred therapy for steroid refractory wAIHA and as part of the first- and second-line treatment of cold agglutinin disease. This article reviews the mechanism of action of the rituximab and current literature its role in management of primary and secondary warm autoimmune hemolytic anemia and cold agglutinin disease.

Plants have evolved tightly regulated strategies to adapt and acclimate to a changing environment to ensure their survival. Various environmental factors affect plant distribution, growth and yield. Low temperature belongs to those abiotic factors which significantly constrain range boundaries of plant species. Exposing plants to low but non-freezing temperature induces a multigenic processes termed cold acclimation, which finally results in an increased freezing tolerance. Cold acclimation comprises reprogramming of the transcriptome, proteome and metabolome and affects communication and signaling between subcellular organelles. Reprogramming of the central carbohydrate metabolism plays a key role in cold acclimation. This review summarizes current knowledge about the role of carbohydrate metabolism in plant cold acclimation. A focus is laid on subcellular metabolic reprogramming, its thermodynamic constraints under low temperature and mathematical modelling of metabolism.

The recent pandemic has greatly stressed supply chains, treatment modalities, and medical resources. Cold atmospheric plasma (CAP) has been used for a wide range of applications in biomedical engineering due to its many components including electrons, charged particles, reactive oxygen species (ROS), reactive nitrogen species (RNS), free radicals, ultraviolet (UV) photons, molecules, electromagnetic fields, physical forces, and electric fields. In this manuscript, we develop CAP devices for COVID-19. Our manuscript indicates the advantages of highlydeployable CAP devices for both sanitation and treatment, without the need for supply chains of special consumables such as hand sanitizers and the like. We hope that this timely research will help engage the broader community of engineers that wish to help the medical community with this pandemic and to prevent and treat future outbreaks.

The fundamental theory of nuclear interactions, Quantum Chromodynamics (QCD), operates in terms of quarks and gluons at higher resolution. At low resolution the relevant degrees of freedom are nucleons. Two-nucleon Short-Range Correlations (SRC) help to interconnect these two descriptions. SRCs are temporary fluctuations of strongly interacting close pairs of nucleons. The distance between the two nucleons is comparable to their radii and their relative momenta are larger than the fermi sea level. According to the electron scattering experiments held in the last decade, SRCs have far-reaching impacts on many-body systems, the nucleon-nucleon interactions, and nuclear substructure. The modern experiments with ion beams and cryogenic liquid hydrogen target make it possible to study properties of the nuclear fragments after quasi-elastic knockout of a single nucleon or an SRC pair. The first SRC experiment at BM@N (2018) with a carbon beam has shown that detection of an intact 11B nucleus after interaction selects out the quasi-elastic knockout reaction with minimal contribution of initial- and final-state interactions. Also, 25 events of SRC-breakups showed agreement in SRC properties as knows from electron beam experiments. The analysis of the second measurement of SRC at BM@N held in 2022 with an improved setup is currently ongoing. The SRC project at JINR moved to a new experimental area in 2023, where the next measurement is being planned in terms of experimental setup and physics goals.

There is an intense need to optimize agrivoltaic systems. This article describes the invention of a new testing system: the parametric open source cold-frame agrivoltaic system (POSCAS). POSCAS is an adapted gardening cold-frame used in cold climates as it acts as a small greenhouse for agricultural production. POSCAS is designed to test partially transparent solar photovoltaic (PV) modules targeting the agrivoltaic market. It can both function as a traditional cold frame, but it can also be automated to function as a full-service greenhouse. The integrated PV module roof can be used to power the controls or it can be attached to a microinverter to produce power. POSCAS can be placed in an experimental array for testing, agricultural and power production. It can be easily adapted for any type of partially transparent PV module. An array of POSCAS systems al-lows for testing agrivoltaic impacts from the percent transparency of the modules by varying the thickness of a thin film PV material or the density of silicon-based cells, and various forms of optical enhancement, anti-reflection coatings and solar light spectral shifting materials in the back sheet. All agrivoltaic variables can be customized to identify ideal PV designs for a given agricultural crop.

The microstructure evolution during the cold rolling and subsequent annealing of Alloy 800H was investigated. Two distinct rolling methods, unidirectional rolling and cross-rolling, were intro-duced. Results show that better ductility was observed in the unidirectional rolling than in cross-rolling, whilst a higher volume fraction of large deformed grains was observed in the cross-rolled plates than in the unidirectionally rolled plates. Recrystallization occurred faster in plates from unidirectional rolling than from cross-rolling.

The as-received commercial Inconel 718 material was solid solution heat treated (ST), cold rolled (CR), and precipitation hardened (PH) to investigate the effects of deformation on tensile properties, hardness, and texture. Three sets of specimens (0%, 20% and 50% CR) were STed at 1100 C/1h, CR and aged (720 °C/8 h + 650 °C/8 h) for the analysis. Ultimate tensile strength (UTS), 0.2% yield strength (YS) and elongation of 50% deformed condition were 1645 MPa, 1512 MPa, and 3.8 %, respectively. The 20 % deformation resulted in a balanced UTS (1348 MPa), YS (1202 MPa) and elongation (11%). Contributions of precipitation hardening to the strength was decreasing, while contribution of CR increases with increasing percentage of deformation. Correspondingly, the size and quantities of  decreased with increasing deformation level. In CR specimens, a high density of nano/micro twins were generated with the twin planes oriented perpendicular to the RD-ND surface. The preferred rotation of the crystals generated the gradient of orientation and internal features of the large austenitic grains. The cross-slip of screw dislocations induced a complete β-fibre, consisting of {110}, {112}, and{123}, with doubled intensity at higher deformation. In addition, the specimens tended to be highly susceptible to the twinning-induced orientation emerged by a predominant ⫽ND. An incomplete but intense α-fibre clustered between {110} and {110} was characterized in the as-deformed condition. Besides achieving highest strength, the current work demonstrates the effects of CR on the material strength without the complex influences of  precipitate.

According to a recent estimate by UN Habitat, approximately 3 billion individuals will require suitable housing by the year 2030. This staggering demand translates to the need for around 96,000 affordable housing units to be constructed each day. However, the conventional construction methods that rely on cement-based concrete and masonry are outdated, lacking innovation, efficiency, and sustainability. In light of these challenges, cold-formed steel emerges as an appealing alternative to traditional construction materials like masonry and concrete. It offers numerous advantages, including easy fabrication, lightweight properties, energy efficiency, the ability to reuse the material at the end of its service life, and a higher level of recyclability. Cold-formed steel buildings are also recognized for their superior insulation and lower energy consumption during operation. Cold-formed steel (CFS) members are created by rolling structurally sound steel sheets into the required shapes using a forming machine, without the need for heat as in the case of hot-rolled steel. While the thickness of these members can range from 0.01 mm to 7 mm, commercial construction of load-bearing walls, roof trusses, and floor joists typically utilizes steel thicknesses of 0.7 mm to 1.2 mm. This paper tries to illustrate the materials and methods employed in the construction of cold-formed steel modular buildings in Sri Lanka[1]. It delves into the material and durability characteristics of cold-formed steel, the design philosophy behind these structures, the development of the building envelope, and the energy efficiency features of the building elements. The findings of this study demonstrate that cold-formed steel buildings can be a highly sought-after alternative for residential construction, offering faster construction timelines, cost-effectiveness, and energy-efficient practices.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

Polyamide 11 (PA11) is a plant-based nylon made from castor beans. Powder bed fusion laser sintering (PBF-LS) is an additive manufacturing process used for PA11 which allows the reuse of the unsintered powder. The unsintered powder is mixed with virgin powders at different refresh rates which has been studied extensively for most semi-crystalline polyamides. However, there is lack of information on the effect of using 100% reused PA11 powder and the number of times it is reused on its own during powder bed fusion laser sintering. This paper investigates the effect of reusing PA11 powder in PBF-LS and number of times it is reused on the dimensional accuracy, density, thermal and tensile properties. From 100% virgin powder to 3rd use of the powder, there is a decrease in powder wastage, decrease in crystallinity and tensile strength. These was associated with the polymerisation and cross-linking process of polymer chains, upon exposure to high temperature. This results in a higher molecular weight and hence density. From the 4th use to 10th reuse, the opposite was observed which was associated to an increase in high-viscosity and un-molten particles which resulted in defects in the PBF-LS parts.

Abstract: Windtech device is a novel tool for measuring the sensation of the ‘cold’. Cold poses numerous challenges for industrial operations, human survival, and living convenience. The impact of the cold is not possible to be quantified just based on temperatures; however other factors such as wind speed, humidity, irradiance have to be taken into consideration. Efforts have been made to develop combined indices such as wind chill temperature (WCT), AccuWeather RealFeel®, and others. The presented article discusses these along with the industrial standards that emphasize on the quantification of the ‘cold’. The following article introduces the Windtech device and its operating principle involving ‘heated temperature’, where the ‘heated temperature’ is affected by environmental parameters including ambient temperature, humidity, wind velocity, and irradiance. The discussed Windtech device is calibrated for operation according to the ISO 11079:2007 standard.

The current investigation presents porous ceramic materials prepared of cenospheres prepared by spark plasma sintering. The impact of sintering temperature, mould diameter (20 and 30 mm diameter) and cenosphere size on the properties of the sintered material was investigated. Shrinkage of the samples during sintering started at 900 °C. Sample shrinkage during sintering increases with increasing temperature and decreases with increasing mould size; increasing sample sintering temperature increases the apparent density of all sample series CS 63-150 µm in 20 mm mould from 0.97 to 2.3 g·cm-3 at 1050 - 1300 °C, in 30 mm mould 0.81 - 1.87 g·cm-3 at 1050 - 1200 °C, in 50 mm mould 0.54 - 0.75 g·cm-3 at 1050 - 1150 °C, while CS 150-250 µm in 20 mm mould 0.93 - 1.96 g·cm-3 at 1050 - 1200 °C. Total porosity decreases from 61.5% to 3.9% with increasing sintering temperature from 1050 to 1250 °C, while open porosity reduces at lower temperatures, with closed porosity being highest in samples sintered at 1150 °C. When the sintering temperature increases from 1050 to 1300 °C, the compressive strength of the CS 63-150 samples produced in a 20 mm mould increases from 11 MPa to 312 MPa. These results correlate with the Rice model, which describes an exponential dependence of compressive strength on material porosity and fully dense material compressive strength.

Abstract: Composite sintered bodies comprising silicon dioxide (SiO2) nanoparticles dispersed in β-tricalcium phosphate (β-TCP) were prepared. The addition of nano-sized colloidal SiO2 to the β-TCP produced well-dispersed secondary phase nanoparticles that promoted densification by suppressing grain growth and increasing volume shrinkage of the sintered bodies. The SiO2 was found not to react with the β-TCP at 1120 °C and the substitution of silicon for phosphorous to produce a solid solution did not occur. This lack of a reaction is ascribed to the absence of avail-able calcium ions to compensate for the increase in charge associated with this substitution. The SiO2 nanoparticles were found to be present near the intersections of grain boundaries in the β-TCP. A β-TCP composite sintered body containing 4.0 wt% SiO2 exhibited a bending strength comparable to that of cortical bone and hence could potentially be used as a bone filling material.

The CuCrSn alloy is promising as high-strength and high-conductivity Cu alloy due to its relative low smelting requirement, while thus far reports on the CuCrSn alloy is still quite lacked. In this study, the microstructure and properties of Cu-0.20Cr-0.25Sn (wt%) specimens prepared under different rolling and aging combinations were comprehensively characterized, in order to reveal the effects of cold rolling and aging on the CuCrSn alloy. The results show that increasing the aging temperature from 400 ºC to 450 ºC can obviously accelerates the precipitation, and the cold rolling before aging significantly increases the initial microhardness and promotes the precipitation. Whereas, the deformation hardening will be eliminated during the aging process, making the microhardness even decrease monotonically when the aging temperature and the rolling ratio before aging are high. Performing the cold rolling after the aging can maximize the effects of precipitation strengthening and deformation strengthening, and its adverse impact on the conductivity is not serious. A tensile strength of 506.5 MPa and a conductivity of 70.33% IACS were obtained with such a treatment, only the elongation decreases. Different strength-conductivity combinations of the CuCrSn alloy can be achieved through appropriate combinations of the aging and post aging cold rolling conditions.

Cold chains are essential in providing us humans with food and medicine across the globe. However, cold transportation, like all transportation, has massive negative impacts on the environment and human well-being, which especially culminate in cities. Thus, it is important to research the ways to reduce these impacts and reinvent urban logistics infrastructure. In this article, we articulate the massive problems the road-based transportation sector imposes on the environment and on the health of humans, especially in cities. We present algorithms that show promise in optimizing the whole road transportation sector as well as some innovations and alternative ways to model cities and the whole urban transportation infrastructure. We approach the issues discussed specifically from the point of view of refrigerated transportation, but many of the solutions can be applied to all the transportation sector in general.

Cold chain logistics of Agricultural Products demand forecasting can provide the scientific basis for the country to formulate logistics strategy, which further promotes the development of social economy and the improvement of living standards in China. In this paper, a new mathematical combined model is proposed to Agricultural Products Demand. Shandong, one of a China’s province, serves as the main producer and distributor of agricultural products. Based on the index system created from multiple related factors influencing cold chain logistics demand of agricultural products in Shandong, this paper employs principal component analysis to reduce the dimension of various indexes and predicts principal components with time series. Thereafter, multiple linear regression model and neural network model were constructed to forecast the cold chain logistics demand of agricultural products in Shandong, and their combined forecast models were compared. What's more, the paper provides insight for reference and decision-making concerning the development of cold chain logistics industry of agricultural products in Shandong province.

Comparison of the influence of conditioning temperature of microspheres made of medical grade poly(L-lactide) (PLLA) and polylactide with 4wt.% of D-lactide content (PLA), on its thermal and structural properties is presented. The microspheres were fabricated by solid-in-oil-in-water method for application in additive manufacturing. The microspheres were annealed below glass transition temperature (Tg), above Tg but below onset of cold crystallization, and at two temperatures selected from the range of cold crystallization corresponding to crystallization of α’ and α form of poly(L-lactide) respectively, i.e., at 40°C, 70°C, 90°C and 120°C, in order to verify the influence of conditioning temperatures on sinterability of microspheres set as sintering window (SW). Based on differential scanning calorimetry measurements SW of microspheres were evaluated with consideration of existence of cold crystallization and reorganization of crystal polymorph. The results indicate that the conditioning temperature influence on availability and range of SW that depending on the D-lactide presence. We postulate the need for an individual approach for polylactide powders in determining the SW as a temperature range free of any thermal events. Moreover, other core powder characteristic, such as residual solvent content, morphology, particle size distribution, powder flowability and thermal conductivity, as a key property for successful laser sintering, are characterized. The microspheres are close to sphere and the size of microspheres are below 100 µm. Residual solvents content decreases with the increase of annealing temperature. The thermal conductivity is 0.073 W/mK and 0.064 W/mK for PLA and PLLA microspheres, respectively, and it depends on the spherical shape of the microspheres. Furthermore, the WAXD studies prove that an increase in the conditioning temperature causes a slight increase in crystallinity degree for PLLA microspheres and clear increase in crystallization for PLA microspheres.

The growth of solid particles during liquid phase sintering was modeled by the Cellular Automata method. The binary phase diagram and Fickian approach for the diffusion process were applied to simulate the chemical composition variation in liquid and solid phases during sintering. The Oswald-Ripening effect was considered during the dissolution of the solid phase in the liquid phase. It is used to define the probability of solid-phase dissolution by the liquid phase and develop the model to simulate the alloy with solid solubility. So, the microstructure could be modeled in the liquid phase sintering process.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

Intermittent cold exposure has garnered increased attention in popular culture, largely for its proposed effects on mood and immune function, but there are also suggestions that the energy wasting mechanisms associated with thermogenesis may decrease body weight and fat mass. Considering the continued and worsening prevalence of obesity and type II diabetes, any protocol that can reduce body weight and/or improve metabolic health would be a substantial boon. Here, we present a narrative review exploring the research related to ICE and adipose tissue. Any publicly available original research examining the effects of repeated bouts of ICE with adipose related outcomes was included. While ICE does not consistently lower bodyweight or fat mass, there does seem to be evidence for ICE as a positive modulator of the metabolic consequences of obesity, such as glucose tolerance and insulin signaling. Further, ICE consistently increases the activity of brown adipose tissue (BAT) and transitions white adipose tissue to a phenotype more in line with BAT. Lastly, the combined effects of ICE and exercise do not seem to provide any additional benefit, at least when exercise is done during ICE bouts. The majority of the current literature on ICE is based in rodent models where animals are housed in cold rooms, which does not reflect protocols likely to be implemented in humans such as cold-water immersion. Future research could specifically characterize ICE via cold water immersion in combination with controlled calorie intake to clearly determine the effects of ICE as it would be implemented in humans looking to lower bodyweight via reductions in fat mass.

Cold stress is a major environmental factor affecting the growth, development, and productivity of various crop species. With the current trajectory of global climate change, low temperatures are becoming more frequent and can significantly decrease crop yield. Wheat (Triticum aestivum L.) is the first crop to be domesticated and is the most popular cereal crop in the world. Due to a lack of systematic research on cold response pathways and gene regulatory networks, the underlying molecular mechanisms of cold signal transduction in wheat are poorly understood. This study reviews recent progress in wheat, including the ICE-CBF-COR signaling pathway in cold stress and the effects of cold stress on hormonal pathways, reactive oxygen species (ROS), and epigenetic regulation. This review also highlights outstanding issues that are crucial for understanding the interactions between wheat and low-temperature conditions.

The efficiency of cold sheet and strip rolling of steels and non-ferrous metals in the main depends on the quality of the technological lubricant and its cost. In this regard, it is important to develop new compositions of effective metal-working coolants (MWC) having low cost and providing the maximum reduction in the friction coefficient. We developed and tested the new compositions of the MWC on basis of chicken fat, and mono- and diglycerides and their esters of boric acid synthesized from the wastes of sunflower oil production. The MWC were tested in DSEA on laboratory rolling mill 100x100 with a roll diameter of 260 mm during steel 08Kp rolling. The efficiency of the coolants was determined by the factor of metal stretch forming λ and the coefficient of friction μ in the deformation zone which was found by forward slip method. We found the metal-working coolant with 100 % concentration of boric acid esters of mono- and diglycerides is the most effective in steel rolling. Thus the new MWC on basis of boric acid esters of mono- and diglycerides synthesized from the wastes of sunflower oil production can be recommended for use in rolling of structural steels on account of availability, high efficiency, and a low cost.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

Cold plasma (CP) is an ionised gas containing excited molecules and ions, radicals, free electrons, and emits electric fields and UV radiation. CP is potently antimicrobial and can be applied safely to biological tissue, birthing the field of plasma medicine. Reactive oxygen and nitrogen species (RONS) produced by CP affect biological processes directly or indirectly via the modification of cellular lipids, proteins, DNA, and intracellular signalling pathways. CP can be applied at lower levels for oxidative eustress to activate cell proliferation, motility, migration, and antioxidant production in normal cells, mainly potentiated by the unfolded protein response, Nrf2-activated antioxidant response element and PI3K/Akt pathway, which also activates NFκB. At higher CP exposures, inactivation, apoptosis and autophagy of malignant cells can occur via degradation of PI3K/Akt and MAPK-dependent and -independent activation of the master tumour suppressor p53, leading to caspase-mediated cell death. These opposing responses validate a hormesis approach to plasma medicine. Clinical applications of CP are becoming increasingly realised in wound healing, while clinical effectiveness in tumours is currently coming to light. This review will outline advances in plasma medicine and compare the main redox and intracellular signalling responses to CP in wound healing and cancer.

The contact materials in high-voltage vacuum interrupter require properties such as high conductivity, high density, and high hardness to minimize arc heat damage. In this study, copper–molybdenum-chromium alloys contact materials are examined for a high voltage contact material. Ball milling process was carried out after analyzing the raw materials of copper, chromium, and molybdenum powders. A green compact was produced using a high press with the mixed powder. Afterwards, composite was produced by sintering method according to temperature and infiltration method according to Cu content in green compact. The composite of sintering method showed a density of 8.55 g/cm3 (relative density 93%) a hardness of 217 HV, and an electrical conductivity of 40.7 IACS% at 1200 °C. The composite of 10 wt.% Cu produced by the Cu infiltration method showed a density of 8.7 g/cm3 (relative density 94%), Hardness of 274HV and electrical conductivity of 39 IACS% at 1300 °C. The measurements of physical properties showed the new possibility of using the Cu–Cr–Mo alloy as a contact material for high-voltage vacuum interrupters.

The production of particles outside the region of nucleon-nucleon kinematics due to interactions involving dense cold clusters of quark-gluon matter in nuclei is calculated. The possibility of observing this process in the region of central rapidities and large transverse momenta in heavy ion collisions at low energies with MPD detector at the NICA collider has been demonstrated.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

A modification to the conventional spark plasma sintering (SPS) process was undertaken to allow edge-free deformation of grains longitudinally to the loading axis in a process termed spark plasma texturing (SPT). The resulting Al7075 SPT compact was compared to SPSed Al7075 in terms of densification behaviour, microstructural evolution, and mechanical properties. The result reported herein highlights the unique benefits of the SPT technique and potential application in the manufacturing of advanced materials.

The research results conducted on binderless tungsten carbide (WC) ceramics obtained by Spark Plasma Sintering (SPS) of WC powders with different average particle sizes (0.095, 0.8, 3 μm) are presented. Nonuniform distribution of crystalline phases and microstructure of the WC ceramics was studied using layer-by-layer XRD analysis and SEM. Surface layers of the WC-based ceramics are characterized by nonuniform distribution of W2C crystalline phase and grain sizes, including the appearance of abnormally large grains. Thickness of the nonuniform layer was at least 50 μm. The effect under study is associated with an intense carbon diffusion from graphite foil. On the one hand, this contributed to a decrease in the intensity of W2C phase particle formation, which is transformed into α-WC phase due to the carbon. On the other hand, it caused abnormal grain growth in the layer where the carbon diffused. The obtained value of the carbon diffusion depth exceeds the values known from the literature (up to 1 μm in the case of volume diffusion even at temperature of 2370℃ and exposure time of ~ 60 h). The use of boron nitride (BN) as a protective coating on graphite mold parts did not prevent the formation of nonuniform layer on the ceramic surface.

Nano Silicon carbide reinforced aluminum (Al/nanoSiC) metal matrix composites are attractive because of their superior properties such as high strength and stiffness, Application of aluminum in technological and structural application is growing steadily. The major limitation for metal matrix nano composites, however, is their propensity to brittle fracture. The new technologies and new materials are two basic aims for companies. In this research, the effect of addition Al/SiC nano particles on microstructure and mechanical properties of pure aluminum has been investigated. Pure aluminum powder and various fractions of SiC particles with an average diameter of 50 nm were milled by a high-energy planetary ball mill to produce nanocrystalline Al–SiC nanocomposite powders. Pressing and sintering applied to consolidate powders to tablet shape. Then the samples were rolled to cylindrical shape. The nano SiC Percentage were 0%, 2.5%, 5%, 7.5%, 10% , 12,5% and 15%. Mechanical tests such as tensile, hardness, fracture toughness and young’s modules measurement carried out to study the mechanical behavior of each alloy. Scanning electron microscopy was used to study the morphology and microstructure of nanocomposite powders and bulk samples. The role of wt% fraction of SiC nanoparticles was investigated. The results shows that the addition of SiC nano particles has significant influence on the microstructure and mechanical properties of composites and usually the optimum properties depends on wt% SiC.

Cold atmospheric plasma (CAP) has emerged as a promising therapeutic technology, distinguished by its safety, efficiency, and minimal side effects. With increasing applications in dermatology, CAP demonstrates antimicrobial efficacy against bacteria, viruses, and fungi, supports tissue proliferation and wound healing, and hinders the growth and migration of tumor cells. This review encompasses the concept, physical characteristics, and current research applications of CAP in dermatology. CAP, a gas cloud produced by ionizing gases, operates at room temperature, ensuring safety and efficacy in dermatological use. Its effects are mediated through active components like reactive oxygen and nitrogen species (RONS) and ultraviolet radiation. The extensive research covered in this paper explores CAP's applications in skin infections, immune-related diseases, and tumor diseases. As a biologically suitable technology, cold atmospheric pressure plasma finds widespread use in medicine, including medical device sterilization, dentistry, oncology, and dermatology. The direct and indirect forms of CAP applications, including plasma-activated liquids, complement each other. CAP holds promise as a dermatological treatment technique, but further exploration and research are needed. This article briefly explores CAP's diverse applications and potential utility within dermatology. The objective is to enhance the progress of plasma medicine by furnishing a concise overview of the applications of this groundbreaking technology in dermatological contexts.

Carbonate rocks occupy about 6490 km2 in Albania (23% of the country) and the total exploitable karst water resources are estimated in 2.84*109 m3/year (about 65% of the total exploitable groundwater resources in the country, and about 70% of those used for water supply). In addition, karst massifs are very rich in thermal waters, related to the ascending fluids which are essential for the development of hypogenic karstification in the outer Albanides. This type of karst facilitates the circulation regime of deep fluids, which are revealed at the surface through both numerous phenomena of hypogene karst and hot springs. The relatively small Kruja Tectonic Zone is characterized by the presence of SE-NW oriented carbonate structures, rich in thermal sources, and contains more than the 80% of Albania thermal springs. One of its most interesting carbonate structures, for the presence of both cold and thermal waters, is the small karst structure of Makaresh, with a surface of 22 km2. The purpose of this article is to describe the characteristics and factors that affect the quantitative and qualitative formation of cold and thermal groundwater in this massif. Based on the physico-chemical characteristics, groundwaters of the study area are classified in cold and thermal waters. The former are mainly of HCO3-Ca or HCO3-Ca-Mg type (Electrical Conductivity 580-650 μS/cm, Temperature 13.9-16.6° C). Thermal waters are mainly of the Cl-Na-Ca type (EC 7200-7800 μS/cm, T 18.5-22.5° C); further, they are characterized by high hydrogen sulphide concentration, up to about 350 mg/l. The presence of two groundwater types in the Makaresh massif is connected to the presence of two groundwater circulation systems. The main factors of the groundwater physic-chemical quality are the solution of rocks and minerals therein contained, the presence of hypogenic speleogenesis, and the mixing of the groundwater of the two systems. The hydrogeological studies proved that karst rocks contain considerable fresh water resources; the capacity of water wells used for the drinking water supply reaches up to about 50 l/s. Thermal waters are not currently exploited due to their temperature, but they are potentially suitable for thermal uses, by drilling boreholes at depth of about 1000 m.

In view of the problem that the hot and cold loads of mushroom houses are affected by multiple factors such as environment, mushrooms, and equipment, which are difficult to accurately model, this paper proposes a short-term load prediction method based on empirical wavelet transform (EWT) and mixed autoregressive integrated moving average (ARIMA) and convolutional bi-directional short- and long-term attention mechanism (CNN-BiLSTM-Attention). The method first uses the Boruta algorithm to filter the input characteristics, and then uses the EWT method to decompose the mushroom house load data into 4 modal components. Then the Lempel-Ziv method is introduced to divide the modal components into two categories of high and low frequencies, and the CNN-BiLSTM-Attention and ARIMA prediction models are constructed separately. Finally, the two types of prediction results are superimposed and reconstructed to obtain the final load prediction value. The test results show that the Boruta algorithm can effectively filter out the characteristics of key influencing factors. Compared with the Spearman and Pearson correlation coefficient methods, the mean absolute error (MAE) of the prediction results is reduced by 14.72% and 3.75%, respectively; compared with the ensemble empirical mode decomposition (EEMD) method, the EWT method can increase the decomposition and reconstruction error by 103 orders of magnitude, which can effectively improve the prediction accuracy of the model; compared with the individual neural network model, the prediction effect of the model proposed in this paper has obvious advantages, and the MAE, root mean square error (RMSE) and mean absolute percentage error (MAPE) of the prediction results are reduced respectively. 31.06%, 26.52% and 39.27%.

Airway epithelial cells (AECs) play a key role in maintaining lung homeostasis, epithelium regeneration and the initiation of pulmonary immune responses. To isolate and study murine AECs investigators have classically used short and hot (1h 37°C) digestion protocols. Here, we present a workflow for efficient AECs isolation and culture, utilizing long and cold (20h 4°C) dispase II digestion of murine lungs. This protocol yields a greater number of viable AECs compared to an established 1h 37°C dispase II digestion. Using a combination of flow cytometry and immunofluorescent microscopy, we demonstrate that compared to the established method, the cold digestion allows for recovery of a 3-fold higher number of CD45-CD31-EpCAM+ cells from murine lungs. Their viability is increased compared to established protocols, they can be isolated in larger numbers by magnetic-activated cell sorting (MACS), and they result in greater numbers of KRT5+p63+ colonies in vitro. Our findings demonstrate that temperature and duration of murine lung enzymatic digestion have a considerable impact on AEC yield, viability, and ability to form colonies in vitro. We believe this workflow will be helpful for studying lung AECs and their role in the biology of lung.

Cold brew coffee has emerged as a new trend during the last decade. However, “cold brew” is an extraction style of ground roasted coffee with water at less than body temperature (typically 8°C or room temperature) rather than a beverage per se. Cold brew extraction poses several challenges including the need of specific optimization depending on the multivariate influences of coffee variety and processing, roast degree, grinding, dosage, water composition, turbulence, brew system (drip, immersion etc.), time and temperature. While cold brew is typically characterized by a floral sweetness, over-extraction may lead to abundant acidity and bitterness. To avoid this, an extraction degree of 70% was suggested using rather shorter times (i.e. 2 h at 15°C with 80 g/L coffee with optimized medium roast profiles). Due to the lack of sterilizing temperatures during preparation, cold brew is special in the coffee sector because hygiene and food safety aspects pose specific challenges for food industry. To avoid microbiological contamination and spoilage, cold brew should be as freshly prepared as possible and shelf-life should be minimized.

Cold gas dynamic spray (CS) is a unique technique to deposit material using high strain rate solid state deformation. A major challenge for this technique is its dependence on the powder properties and lack of standards to assess them between lots and manufacturers. The motivation of this research was to understand the variability in powder atomization techniques for stainless steel powders and their subsequent properties for their corresponding impact on CS. A drastic difference (~30%) was observed in deposition efficiencies (DE) of unaltered, spherical, and similar sized stainless steel (316) powders produced using centrifugal (C.A) and traditional gas atomization (G.A) techniques. The study highlights more on differences on precursor level. Using recent advancements in large scale statistical measurements like laser diffraction shape analysis, µCT scanning, traditional methods like EBSD, nano-indentation, an attempt is made to understand the powder property. Insights on powder size and shape are documented. Significant differences were observed between C.A and G.A powders in terms of grain size, fraction of higher angle grain boundaries (HAGB) and nano hardness. The outcomes of this study would be helpful to understand the commercialization of the cold-spray process for bulk manufacturing of powder precursors

Susceptibility to economically-important diseases of grapes is critical to the evaluation of germplasm recommended for commercial production and for development of sustainable production systems. In 2018-2019, nine cold-hardy grape cultivars including ‘Brianna’, ‘Crimson Pearl’, ‘Itasca’, ‘Louise Swenson’, ‘Marechal Foch’, ‘Marquette’ ‘Petite Pearl’, ‘St. Pepin’, and ‘Verona’ were evaluated on non-treated vines for susceptibility to downy mildew, powdery mildew, black rot, anthracnose, Phomopsis leaf spot and fruit rot, and Botrytis bunch rot. No cultivars were consistently disease-free, and all exhibited some degree of black rot and powdery mildew infection. Relative susceptibility to disease was not consistent across both years, but ‘Brianna’ had greater incidence of black rot and ‘Louise Swenson’ showed lower incidence of powdery mildew in both years. The relatively new cultivars ‘Crimson Pearl’ and ‘Verona’ exhibited comparatively moderate disease susceptibility overall. Growers typically manage diseases with fungicides on commercial farms, so cultivar susceptibility is just one component of a sustainable pest management and production system.

The concept of this prototype is to create a cold air film layer, in indoor side of the window. The function of this extra cold air layer is to increase the amount of window resistance and decrease its U-Value. It provide air film layer by using the same concept of desert cooler or wind catcher. They both bring the hot air from outside then let it go throw straw miost with cold water. After hot air move through straw, it would become cold, thus increase the window resistance and decrease the haet gian, therefore, decrease the cooling load. So, this window model works by heating the air in air room by sun radiation, then after a while, air pressure will rise and its volume will increase then it will impulse to wet hay, and become cold. Then there is fins to guide air flow to its correct direction, thus inner side of window will become cold, not like other type of window which when temperature rise, the inner side of window become hot. So, this window prevents heat transition and creare regenereted trubouland air flim in the inner side of the window. Using calculation to find air film characteristics and WINDOW7.7 software to calculate heat gain through window, shows that it is expected from this prototype to reduce heat gain by 6.85 % for double glazed clear window.

The maritime sector, grapples with environmental challenges, but the adoption of "cold ironing" emerges as a promising solution, signifying a shift toward sustainability by providing energy to ships at port, reducing reliance on fossil fuels, and significantly lowering emissions, contributing to global climate change efforts. This transition towards renewable energy is especially crucial for islands like Lesvos, addressing challenges of high energy costs and environmental degradation resulting from reliance on imported fossil fuels, highlighting the potential for positive economic and environmental impacts. The existing literature highlights a research gap in the development of Renewable Energy Sources (RES) to support cold ironing operations, specifically due to the absence of specific data for the power demand needed in such operations and the lack of monitoring data for accurate calculations. This study's primary objective is to utilize real monitoring data from the port of Lesvos to evaluate the power demand for a potential cold ironing application. Additionally, the study aims to analyze the implementation of a wind power park to meet the energy needs of an electric port and evaluate the potential reduction in CO2 emissions. The database of Marine Traffic S.A. was utilized, while the determination of the energy used in-port per ship depended on factors such as the number of arrivals, the duration of hoteling, and the type of engine used by the ships. In addition, the software RETSCREEN was used for the energy analysis of a simulated 20 MW wind park that can support the in-port operations. The combined monthly energy demand for both main and auxiliary engines of shipping vessels at Mytilini port was assessed to be 6118 MWh and averaging a power demand equaled to 8.2 MW. The simulation analysis indicates that the annual electricity delivered to the port can be72080 MWh, with a significant portion remaining unused and exported to the grid, amounting to 14956 MWh annually. Due to demand fluctuations, in-port activities require an additional 924 MWh from the main electrical grid, which highlights the importance of additional measures like energy storage and demand-response practices for the gradual transition to 100% Renewable Energy Sources (RES) operations.

Flood records of the Kunmalik River in Chinese Tien Shan mountains have showed that glacier- dammed lake outburst floods (GLOF) had occurred almost every year since 1956 from the glaci-er-dammed Lake Merzbacher. However, GLOF in cold season is seldomly studied. The defense and management of the flood need further observation and study. The maximum peak discharge of 825 m3/s occurred on 5th December 1996 with the maximum flood volume of 2.875×108 m3, which was 18 times larger than that of the mean daily discharge in winter over the past six decades. The drainage of the Merzbacher lake is not a mechanical breaking up of the glacier dam, but the release of pressurized water along a subglacial tunnel triggered by quickly surge of the Northern Glacier, the subglacial tunnels are enlarged by both ice melting and frictional heat in the flooding water and heat under the glaciated dam and the lake in winter. There is no correlation between the GLOF size and air temperature of cold season. The floods in cold season have become bigger since 1996 than that before, and the flood duration has been extended from winter to spring. Once the cold GLOF starts, its discharge can be forecasted day by day to extrapolate the monitoring hydrograph as a linear curve.

In the present study, a nanostructured FeAl coating was prepared by cold spraying of ball milled powder. Annealing treatment was applied to the coating to investigate its effect on the microstructure, phase structure and microhardness of the cold-sprayed nanostructured FeAl coating. The results showed that the FeAl phase was kept unchangeable when the coating annealed at the temperature above 500oC. Annealing temperature significantly influenced the microstructure and microhardness of cold-sprayed FeAl coating. With raising annealing temperature, the lamellar structure in the as-sprayed coating disappeared and a dense coating microstructure with fully bonding of deposited particles at their interfaces was achieved after annealing at 950oC. Nanograin growth of the FeAl phase occurred at an annealing temperature higher than 800oC. The microhardness of cold-sprayed FeAl coating remained about 400 Hv0.1 at the annealing temperature below 800oC and decreased to 300 Hv0.1 at 1100oC.

Cold brew coffee is a new trend in coffee industry. This paper presents pilot studies into several aspect of this beverage. Using an online survey, the current practices of cold brew coffee preparation were investigated identifying a rather large variability with a preference for extraction of medium roasted Arabica coffee using 50-100 g/l at 8°C for about 1 day. Sensory testing using ranking and triangle tests showed that cold brew may be preferred over iced coffee (cooled down hot extracted coffee). Extraction experiments at different conditions combined with nuclear magnetic resonance (NMR) analysis showed that the usual extraction time may be longer than necessary as most compounds are extracted within only a few hours, while increasing turbulence (e.g. using ultrasonication) and temperature may additional increase the speed of extraction. NMR analysis also revealed a possible chemical differentiation between cold brew and hot brew using multivariate data analysis. Decreased extraction time and reduced storage times could be beneficial for cold brew product quality as microbiological analysis of commercial samples detected samples with spoilage organisms and contamination with Bacillus cereus.

In the present study, hypereutectic Al-Si alloy compacts and Al-Si/B4C composites were produced by conventional, microwave and spark plasma sintering techniques. The effects of sintering techniques and B4C particle addition on microstructural properties, density, hardness and electrical conductivity were investigated. The microstructures were examined with an optical microscope. Densities were measured using the Archimedes technique. Electrical resistance measurements were made with the four-point probe measurement technique. Elemental Al grains, master alloy grains and primary Si particles were determined in the microstructures of all samples. The addition of 15 wt% B4C caused the porosity rate to increase in the samples. Samples produced with SPS technique gave ≈80% higher hardness values than samples produced with CS and MWS. Compared to the samples produced with CS and MWS, the samples produced with SPS gave higher electrical conductivity values. Electrical conductivities were decreased as the weight percentage of B4C increased in all samples.

Switched-mode power supplies (SMPS) often utilize electrolytic capacitors due to their substantial energy density and economical pricing. However, their ability to function at low temperatures is essential for dependable operation in several sectors, including telecommunications, automotive, and aerospace. This study includes an experimental evaluation of how well standard SMPS electrolytic capacitors operate at low temperatures. This paper investigates the suitability of standard electrolytic capacitors used in switched-mode power supplies (SMPS) for low-temperature applications. The experimental evaluation exposed the capacitors to temperatures ranging from - 5 ∘C to - 40 ∘C, assessing capacitance (Cp), impedance (Z), dissipation factor (DF), and equivalent series resistance (ESR) at each temperature. The capacitor’s time-domain electrical signals were analyzed using the Pearson correlation coefficient to extract discriminative features. These features were input into an Artificial Neural Network (ANN) for training and testing. Results indicated a significant impact of low temperatures on capacitor performance. Capacitance decreased with lower temperatures, while ESR and leakage current increased, affecting stability and efficiency. Impedance proved to be a valuable diagnostic tool for identifying potential capacitor failure, showing a 98.44% accuracy drop at - 5 degrees and 88.75% at the peak temperature, indicating proximity to the manufacturer’s specified limit. The study suggests further research and development to improve electrolytic capacitors’ performance in SMPS systems under cold conditions to enhance efficiency and reliability.

The shortage of precooling equipment in litchi producing regions could lead to a high loss rate, poor quality of litchis. It is urgent to develop a portable precooling device for litchi producing regions. In this study, a novel spray hydrocooler with thermal energy storage (TES) were designed, fabricated, and tested. A simple mathematical model of TES capacity, ice coil thermal resistance and refrigeration system was employed to determine hydrocooler parameters. Then designed the structure of the spray hydrocooler. Maximum charging test was implemented with full TES capacity and litchi spray hydrocooling experiments were carried out at different charging times, spray flow rate, and litchi load with one-third TES capacity. Results showed that: (1) the spray hydrocooler allows for the rapid and effective precooling of litchis; (2) the hydrocooler can precool 299 kg litchis with one-third TES storage, meet the precooling requirements; (3) the effective TES capacity achieved 1.25×108 J at the maximum TES capacity of the hydrocooler, while the energy efficiency ratio (EER) is 2; (4) the precooling capacity was maximum and the average power consumption was minimum when the litchi load was 23 kg and the spray flow rate was 30 L min-1. Longer charging time is the most important factor in increasing precooling capacity and reducing average power consumption.

This paper presents the results of an experimental and analytical study on the behavior of cold-formed thick-walled steel plates connected by a single bolt under double shear. Experimental studies were conducted on a total of 54 bolted connections fabricated from two thickness of cold-formed thick-walled steel plates with the nominal thickness of 6 mm and 10 mm. The effects of end distance, edge distance and steel plate thickness were investigated on the bolt bearing behavior. Codes of (modified) ANSI/AISC 360-16 and EN1993-1-8 were applied to predict failure modes and bearing resistance of connections and the predictions were compared with that of measurements. A method was proposed to calculate the elongation of bolt hole at ultimate load. The studies show that fractures occurred on shear planes of specimens failed by shear out due to reduced ductility caused by cold forming process. The modified ANSI/AISC gives the most accurate predictions of failure modes and bearing resistance. However, the bearing resistance will be overestimated if the reduction in area of shear planes caused by occurrence of fracture is ignored for specimens with end distance being higher than 2.0d0 and a reduction factor is needed for calculating bearing resistance of connections. The method proposed in our paper can predict the elongation of bolt hole very well.

Following the concept of strong interaction, theoretically, fusion of proton seems to increase the binding energy of final atom by 8.8 MeV. Due to Coulombic repulsion, asymmetry effect, pairing effect and other nuclear effects, final atom is forced to choose a little bit of binding energy less than 8.8 MeV and thus it is able to release left over binding energy in the form of internal kinetic energy or external thermal energy. Thus, in cold fusion, heat release to occur, binding energy difference of final atom and base atom seems to be less than 8.8 MeV. Qualitatively, energy released during cold fusion seems to be approximately equal to 8.8 MeV minus the difference of binding energy of final and base atoms. Based on this idea, under normal conditions, for the case of ₂He⁴, fusion of four protons can liberate (35.2-28.3)=6.9 MeV and it is 3.5 times less than the current estimates. Point to be understood is that, lesser the binding energy of final atom, higher the liberated thermal energy and vice versa. With a suitable catalyst and sufficient hydrogen under suitable pressure, if reactor’s temperature is maintained at (1000 to 1500) ⁰C, there seems a lot of scope for a chain reaction of cold fusion in which light isotopes transform to their next stage with increased proton number or mass number and liberate safe and clean heat energy continuously. By arranging 4 to 6 reactors and charging them periodically in tandem, required thermal energy can be produced continuously. In this new direction, by carefully selecting the base isotope and its corresponding catalyst, experiments can be conducted and ground reality of cold fusion can be understood at various temperature and pressure conditions.

Groundwater is a vital resource for human welfare. However, due to various factors, groundwater pollution is one of the main environmental concerns facing. Yet, it is challenging to simulate groundwater quality dynamics due to the insufficient representation of nutrient percolation processes in the soil and Water Assessment Tool model. The objectives of this study were extending the SWAT module to predict groundwater quality. The results proved a linear relationship between observed and calculated groundwater quality considering No3 and TDS with R2, NSE and PBIAS values in the satisfied ranges, albeit underestimation and overestimation were observed due to limited data availability. These results highlight that nitrate and TDS concentrations and variability in groundwater may used as a tool in surface water quality that have to be assumed for designing adaptive management scenarios. Hence, extended SWAT model could be a powerful tool for future regional to global scale modelling of nutrient loads supporting effective surface and groundwater management.

To elucidate the function of the cold resistance regulatory gene FmNAC1 from Fraxinus mandshurica, this study identified the role that the overexpression of the FmNAC1 gene plays in tobacco growth and cold stress regulation. The cloned FmNAC1 gene from F. mandshurica is 891 bp in length and encodes 296 amino acids. Our subcellular localization analysis confirmed that FmNAC1 is primarily located in the nucleus and functions as a transcription factor. FmNAC1 is responsive to cold and NaCl stress, as well as to the induction of IAA, GA, and ABA hormone signals. To further elucidate its function in cold resistance, four transgenic tobacco lines of FmNAC1 overexpression（FmNAC1-OE）were generated through tissue culture after the agrobacterium-mediated transformation of wild-type (WT) tobacco. These FmNAC1-OE plants exhibited accelerated growth after transplantation. When exposed to low-temperature conditions at -5°C for 24 hours, the rates of wilting and yellowing of the FmNAC1-OE plants were significantly lower than those of the WT tobacco plants. Additionally, the membrane integrity, osmotic regulation, and reactive oxygen species (ROS)-scavenging abilities of the FmNAC1-OE tobacco lines were better than those of the WT plants, indicating the potential of the FmNAC1 gene to improve plant cold resistance. The gene expression results further revealed that the FmNAC1 transcription factor exhibits regulatory interactions with growth-related genes such as IAA and AUX1; cold resistance-related genes such as ICE, DREB, and CBF1; and genes involved in the clearance of reactive oxygen species (ROS), such as CAT and SOD. All of this evidence shows that the FmNAC1 transcription factor from F. mandshurica plays a key role in contributing to the enhancement of growth, cold resistance, and ROS clearance in transgenic tobacco plants.

The visual perception of leisure spaces between residences in cold regions is important for public health. To compensate for the existing researches` lack of ignoring the cold snow season`s influence, this study selected two types of outdoor leisure space environments in non-snow and snow seasons as research objects. An eye tracker combined with a Semantic Difference (SD) questionnaire was used to verify the feasibility of the application of virtual reality technology, screen out leisure gaze characteristics, and reveal the environmental factors related to leisure visual perception. In snow season, spatial aspect ratio (SAR), building elevation saturation (BS), and grass proportion in the field of view (GP) showed strong correlation to the leisure visual perception scores (W). In non-snow season, apart from the above three factors, roof height difference (RHD), tall tree height (TTH) and color contrast (HC) also influenced W obviously. The effects of factors on W were revealed in immersive virtual en-vironment (IVE) orthogonal experiments and genetic algorithm (GA) and k-nearest neighbor algorithm (KNN) were combined to optimized the environmental factors. The optimized threshold ranges in the non-snow season environment were SAR: 1.82‒2.15, RHD: 10.81 m‒20.09 m, BS: 48.53‒61.01, TTH: 14.18 m‒18.29 m, GP: 0.12‒0.15, and HC: 18.64‒26.83. In the snow season environment, the optimized threshold ranges were SAR: 2.22‒2.54, BS: 68.47‒82.34, and GP: 0.1‒0.14.

In this paper, a study was conducted on the Ramsey interference and spectral line locking techniques based on rubidium-87 cold atoms. Using sequential control technique, the timing design of a three-dimensional magneto-optical trap (MOT), cold atoms’ free fall, Ramsey microwave interference, and two-level fluorescence detection was realized, achieving the state preparation of cold atoms and clock transitions. By designing an automatic peak-finding algorithm, numerical integration was performed on the time-of-flying (TOF) signal, and narrow linewidth cold atom Ramsey interference fringes were obtained. Based on this, a frequency-hopping method was used to lock the frequency of the 10MHz oven-controlled crystal oscillator (OCXO) in a closed loop, achieving a linewidth of 38Hz. This preliminary result verifies the feasibility of the system design.

The effects of 1%~5% cold compression on the mechanical properties, microstructure and residual stress of 7050 aluminum alloy were investigated, and the results were applied to the complex die forging with stiffener structure. The results show that with the increase of cold compression, the tensile strength of forging decreases gradually, but the conductivity and fracture toughness of the forging have little change. TEM microstructure shows that with larger cold compression (5%), the dislocation density was relatively higher, which promoted the precipitation and growth of precipitated phases at positions with higher dislocation density during aging process. The ultrasonic tests of residual stress show that with the increase of cold compression, the residual stress in the forging decreases first, and then increases when cold compression reaches 5%. The results of the die forging of 7050 aluminum alloy with bar structure show that the residual stress of the die forging is obviously eliminated after 2-4% cold compression, and the deformation after machining is obviously less than of the uncompressed forgings. The combination of bar and web is more beneficial to the uniform distribution of residual stress of the die forging with bar structure.

Background: The current coronavirus disease 2019 (COVID-19) is spreading globally at an accelerated rate. There is some previous evidence that weather may influence the incidence of COVID-19 infection. We assessed the role of meteorological factors including temperature (T) and relative humidity (RH) considering the concentrations of two air pollutants, inhalable coarse particles (PM10) and nitrogen dioxide (NO2) in the incidence of COVID-19 infections in Finland, located in arctic-subarctic climatic zone. Methods: We retrieved daily counts of COVID-19 in Finland from Jan 1 to May 31, 2020, nationwide and separately for all 21 hospital districts across the country. The meteorological and air quality data were from the monitoring stations nearest to the central district hospital. A quasi-Poisson generalized additional model (GAM) was fitted to estimate the associations between district-specific meteorological factors and the daily counts of COVID-19 during the study period. Sensitivity analyses were conducted to test the robustness of the results. Results: The incidence rate of COVID-19 gradually increased until a peak around April 6 and then decreased. There were no associations between daily temperature and incidence rate of COVID-19. Daily average RH was negatively associated with daily incidence rate of COVID-19 in two hospital districts located inland. No such association was found nationwide. The sensitivity analyses indicate the results are robust. Conclusions: Weather conditions, such as air temperature and relative humidity, may not be important factors affecting the COVID-19 incidence in the arctic and subarctic winter and spring. More evidence is needed on the associations between weather and COVID-19 during different seasons.

The current study aimed to evaluate the influence of different sintering temperatures on the properties of copper aluminum oxide (CuAlO₂) pellets synthesized from copper oxide (CuO) and aluminum hydroxide (Al(OH)₃) for application in smart infrastructure systems. The pellets were sintered at 400 K, 1000 K, and 1300 K, in the presence of nitrogen gas flow to reduce the amount of oxygen availability. The CuAlO₂ sintered nanoparticles were chemically analyzed by X-ray diffractometry, and the nanostructure of the materials was studied by scanning electron microscopy. The transmittance of the sintered materials was examined by ultraviolet/visible (UV/Vis) spectrophotometry, and 88% transparency was observed for the pellets sintered at 1300 K. Electrical conductivity was measured at 0.905 mS/cm, indicating a semiconducting behavior.

Complex proteomic and physiological approaches to study cold and heat stress responses in plant mitochondria are still limited. Variations in the mitochondrial proteome of cauliflower (Brassica oleracea var. botrytis) curds after cold and heat and after stress recovery were assayed by 2D PAGE in relation to respiratory parameters. Quantitative analysis of the mitochondrial proteome revealed numerous stress-affected protein spots. In cold alternative oxidase isoforms were extensively upregulated; major downregulations in the level of photorespiratory enzymes, porine isoforms, oxidative phosphorylation (OXPHOS) and some low-abundant proteins were observed. On the contrary, distinct proteins, including carbohydrate metabolism enzymes, heat-shock proteins, translation, protein import, and OXPHOS components were involved in heat response and recovery. Few metabolic regulations were suggested. Cauliflower plants appeared less susceptible to heat; closed stomata in heat stress resulted in moderate photosynthetic, but only minor respiratory impairments, however photosystem II performance was unaffected. Decreased photorespiration corresponded with proteomic alterations in cold. Our results show that cold and heat stress not only operate in diverse mode (exemplified by cold-specific accumulation of some heat shock proteins), but exert some associations on molecular and physiological levels. This implies more complex model of action of investigated stresses on plant mitochondria.

Land surface temperature (LST) is a key variable in surface-atmosphere energy and water exchanges. The main goals of this study are to (i) evaluate the LST of the European Centre for Medium-Range Weather Forecasts (ECMWF) ERA-Interim and ERA5 reanalyses over Iberian Peninsula using the Satellite Application Facility on Land Surface Analysis (LSA-SAF) product and to (ii) understand the main drivers of the LST errors in the reanalysis. Simulations with the ECMWF land-surface model in offline mode (uncoupled) were carried out over the Iberian Peninsula and compared with the reanalysis data. Several sensitivity simulations were performed in a confined domain centered in Southern Portugal to investigate potential sources of the LST errors. The Copernicus Global Land Service (CGLS) fraction of green vegetation cover (FCover) and the European Space Agency’s Climate Change Initiative (ESA-CCI) Land Cover dataset were explored. We found a general underestimation of daytime LST and slightly overestimation at night-time. The results indicate that there is still room for improvement in the simulation of LST in ECMWF products. Still, ERA5 presents an overall higher quality product in relation to ERA-Interim. Our analysis suggested a relation between the large daytime cold bias and vegetation cover differences between (ERA5 and CGLS FCocver) with a correlation of -0.45. The replacement of the low and high vegetation cover by those of ESA-CCI provided an overall reduction of the large Tmax biases during summer. The increased vertical resolution of the soil at the surface, has a positive impact, but much smaller when compared with the vegetation changes. The sensitivity of the vegetation density parameter, that currently depends on the vegetation type, provided further proof for a needed revision of the vegetation in the model, as there is a reasonable correlation between this parameter and the Tmax mean errors when using the ESA-CCI vegetation cover (while the same correlation cannot be reproduced with the original model vegetation). Our results support the hypothesis that vegetation cover is one of the main drivers of the LST summertime cold bias in ERA5 over Iberian Peninsula.

We report the growth of graphene at a low temperature using the cold wall chemical vapor deposition technique (CWCVD). Few layered (~6-8 layers) graphene were grown on nickel-coated silicon with acetylene as the precursor gas. The advantage of the combination of the acetylene (as a carbon feedstock) and the nickel catalyst was the lowering of the graphene growth temperature. Nickel coated silicon samples were pre-treated (heat treatment in inert atmosphere) before the growth and the effect of the pre-treatment on the catalyst as well as on the grown film was studied. The final samples were characterized with scanning electron microscopy and Raman spectroscopy. In CWCVD route, the heating of only the substrate holder enabled high heating and cooling rates, which, along with the control over partial pressure of the precursor gas had profound effect on the formation of graphene. In the best sample we have achieved almost equal intensity of the G and 2D peaks in Raman spectrum, which implied about ~6-8 layers of Graphene. The defect peak (the D band) was extremely small in the sample and it was attributed to the ripples and the underlying roughness of the nickel film. We analyzed that a proper choice of the thickness of catalyst layer and a higher cooling rate after graphene growth it would be possible to obtain monolayered graphene. Similar samples grown in a normal atmospheric CVD (with some engineered design to promote fast cooling) were also compared with the cold wall CVD grown samples and plasma assisted CWCVD, and cold-wall CVD demonstrated a better control over the quality of graphene film through the fast cooling and a controlled partial pressure of the precursor gas.

Needle abscission in balsam fir has been linked to both cold acclimation and changes in lipid composition. The overall objective of this research is to uncover lipid changes in balsam fir during cold acclimation and link those changes with postharvest abscission. Branches were collected monthly from September to December and assessed for cold tolerance via membrane leakage and chlorophyll fluorescence changes at -5, -15, -25, -35, and -45°C. Lipids were extracted and analyzed using mass spectrometry while postharvest needle abscission was determined gravimetrically. Cold tolerance and needle retention each significantly (P < 0.001) improved throughout autumn in balsam fir. There were concurrent increases in DGDG, PC, PG, PE, and PA throughout autumn and a decrease in MGDG. Those same lipids were strongly related to cold tolerance, though MGDG had the strongest relationship (R2 = 55.0% and 42.7% from membrane injury and chlorophyll fluorescence, respectively). There was a similar, albeit weaker, relationship between MGDG:DGDG and needle retention (R2 = 24.3%). Generally, a decrease in MGDG:DGDG ratio resulted in better cold tolerance and higher needle retention in balsam fir possibly due to increased membrane stability.

Kiwifruits are often exposed to various temperature fluctuation (TF) during postharvest storage. To evaluate the effect of TF on the qualities of kiwifruits, fruits were stored at 2 ºC, 2 ºC or 5 ºC (TF2ºC-5ºC), 2 ºC or 7 ºC (TF2ºC-7ºC), alternating every 12 h. Observations revealed that kiwifruits stored at constant 2 °C showed the lowest loss of weight and vitamin C due to the minimum ethylene production and respiratory rate compared to that of TF2ºC-5ºC and TF2ºC-7ºC. Moreover, the results of RT-qPCR verifed that the expression of genes encoding polygalacturonase, β-galacturonidase, and pectin methyl esterase was significantly increased by the treatment of TF. Hence, TF accelerated the degradation of the cell walls, softening, translucency and relative conductivity of the flesh of kiwifruits. Besides, the impact of TF2ºC-7ºC on kiwifruits was more significant relative to TF2ºC-5ºC. The present study provides a theoretical basis for kiwifruit during cold storage.

The structure and phenomena arising from charge transfer in cold field emission modus in a single closed carbon nanotube under cold field emission conditions were studied. By studying microphotographs in various microscopes - AFM, SEM, TEM it was found inhomogeneities in the form of two types of superlattices. The conductivity of the emitter section of a nanodiode circuit with an emitter made of an individual closed carbon nanotube (CNT) and arrays of closed CNTs was studied. High values of cold field emission were observed, as well as nonlinearity and anomalies of the current-voltage characteristic (I-V characteristics), which manifested themselves in the form of peaks at low and high current values. Peaks in the CVC have distinct areas of negative differential conductivity. It is argued, that the anomalously high currents in the I–V characteristics of cold field emission of electrons from a nanoemitter made of closed CNTs can be associated with a sharp increase in the density of electron states at energies near the van Hove singularity.

The change of habitat pattern is one of the key factors affecting the survival of moose population. The study of habitat landscape pattern is the key to protect Chinese cold temperate forest moose population and monitor the global distribution of moose. By means of MaxEnt model, landscape index calculation and ecological risk assessment model, combined with field survey and infrared camera monitoring data from April 2014 to January 2023, the author evaluated the habitat suitability of moose population in Nanwenghe National Nature Reserve of the Great Khingan Mountains, and divided the range of moose habitat based on the logical threshold of the model. The landscape pattern index of moose habitat was calculated by Fragstats software and a landscape ecological risk assessment model was established to analyze the landscape pattern and ecological risk dynamic changes of moose habitat in 2015 and 2020. The results showed that under the premise of global warming, the habitat landscape contagion index decreased by 4.53 and the split index increased by 4.86 from 2015 to 2020. In terms of ecological risk: the area of low ecological risk areas increased by 0.88%; the area of medium ecological risk areas decreased by 1.11%; and the area of higher ecological risk areas increased by 0.23%. The fragmentation risk of landscape pattern of moose habitat tends to increase, the preferred patch type is dispersed, the degree of aggregation is low, and the risk of patch type transformation increases. And the middle and high ecological risk areas are mainly concentrated in the river area and its nearby forests, showing a fine and scattered distribution. Under the interference of global warming and human activities, the fragmenta-tion trend of moose habitat in the study area is increasing, and the habitat quality is declining, which is likely to cause moose population migration. For this reason, the author believes that the whole cold temperate forest is likely to face the risk of increasing the transformation trend of dominant patch types in the cold temperate coniferous forest region mainly caused by global warming, resulting in an in-crease in the risk of habitat fragmentation. While the distribution range of moose is reduced, it has a significant impact on the diversity and ecological integrity of the whole cold temperate forest ecosystem. This study is helpful for human beings to strengthen their awareness of forest and river protection, avoid further intervention in more human activities, and formulate a reasonable plan for forest protec-tion and sustainable development in cold temperate zones. to provide theoretical reference for effective monitoring and protection of cold temperate forest and moose population dynamics.

‘Arrayana’ mandarin fruits have a short postharvest life and are sensitive to chilling injury (CI) during cold storage. Brassinosteroids (BR) have been used as a sustainable technology to alleviate CI in fruits and improve postharvest quality. This study evaluated the effect of applying the 24-epibrasinolide analogue (EBR), at doses of 5 mg L-1; DI-31 analogue, at 5 and 10 mg L-1; and control, on the main physical and biochemical characteristics of 'Arrayana' mandarin stored at 4°C for 40 days and, subsequently, 7 days at room temperature (shelf life). The application of EBR and DI-31 analogues reduced the appearance of CI in the exocarp of 'Arrayana' mandarin fruits by reducing electrolyte leakage, maintaining membrane integrity, and increasing antioxidant activity and phenol content at the end of cold storage and shelf life. This was especially pronounced with 5 mg L-1 of EBR. Similarly, the BR maintained the postharvest quality of mandarins by reducing weight loss, respiratory intensity and chlorophyll degradation; increasing β-carotene; and maintaining titratable acidity, and soluble solids. Our research reports for the first time CI tolerance in Arrayana mandarin using natural (EBR) and spirostanic (DI-31), analogues and illustrates the tolerance functionality of the DI-31 analog on CI in fruit postharvest.

The present research intents to study the evolution of the skin fatty acids and physiological disorders through cold storage in ‘Golden Delicious’ apples treated with 1-MCP and calcium. Harvested fruit were treated with calcium chloride (Ca), 1-MCP (MCP), Ca+MCP or no treatment (control) then subjected to cold storage at 0.5 ºC for 6 months. Fatty acids composition, Malondialdehyde (MDA) and the physiological disorders bitter pit (BP), superficial scald and diffuse skin browning (DSB) were measured at harvest and after storage plus 7 days shelf-life at room temperature ≈22 ºC. Palmitic acid decreased and linoleic acid increased through time, while oleic and stearic acids had few changes. Unsaturated/saturated fatty acids and MDA increased through time, despite Ca and Ca+MCP were related to lower MDA and lower BP and rotten fruit, after cold storage and shelf-life. In those treatments, the unsaturated/saturated fatty acids were higher, mainly due to higher linoleic acid and lower palmitic acids. Further research is needed to clarify the changes in membrane properties and the effect of some treatments in response to chilling injury through storage.

Microgrid is one of the promising green transition technologies that will provide enormous benefit to the seaport, as a solution to the major concerns in this sector, namely energy crisis, economical and environmental pollution. However, finest design of the microgrid is a challenging task considering different objectives, constraints and uncertainties involved. To ensure the optimal operation of the system, determining the right configuration framework and size for each component in the seaport microgrid at the minimum cost is a vital decision at the design stage. This paper aims to design a hybrid system of seaport microgrid with optimally sized component .The selected case study is the Port of Aalborg, Denmark. The proposed grid-connected structure consists of renewable energy sources (photovoltaic system and wind turbines), an energy storage system and cold ironing as seaport’ loads. The architecture is then optimized by utilizing HOMER to meet the maximum load demand by considering a few parameters such as solar global horizontal irradiance, temperature and wind resources. Then, the best configuration framework is analyzed in terms of economic feasibility, energy reliability and environmental impact.

The CDPK family genes play crucial roles in signal transduction pathways during plant develop-ment and stress response. In this study, we comprehensively analyzed the CDPK family genes in mustard (Brassica juncea L.), resulting in the identification of 101 genes (BjuCDPK1–101) located on chromosomes AA_Chr01 to BB_Chr08. RNA-seq analysis showed that most BjuCDPK genes were predominantly expressed in the root and flower bud, suggesting their organ-specific expression patterns. Furthermore, the expression levels of most BjuCDPK genes were significantly altered by cold stress. The promoter regions of BjuCDPK genes had abundant cis-acting elements related to hormone and stress. The interaction network analysis predicted that BjuCDPK proteins respond to abiotic stress probably via interaction with ABF1, ABF4, and/or DI19. Our findings provide valu-able information for further investigation of the cold stress adaption of mustard via the CDPK signaling pathway.

Despite recent advancements, therapies remain ineffective against advanced oral squamous cell carcinoma (OSCC), resulting in unsatisfactory therapeutic outcomes. Cold atmospheric plasma (CAP) offers a promising approach in the treatment of malignant neoplasms. Yet, the exact mechanisms driving CAP-induced cancer cell death are not fully understood. This study revealed a significant reduction in the viability of OSCC cell lines, inactivation of AKT and ERK, and the downregulation of the miR-21, miR-31, miR-134, miR-146a and miR-211 expression followed the CAP treatment. Pretreatment with ZVAD, 3-MA, and Fer-1 synergistically reduced CAP-induced cell death, indicating a combined induction of variable death pathways by CAP. Activation of AKT and ERK, alongside combined treatments using death inhibitors and miRNA mimics, counteracted the cell mortality associated with CAP. CAP-induced downregulation of miR-21, miR-31, miR-187 and miR-211 expression was rescued by AKT and ERK activation. Additionally, CAP treatments notably inhibited the growth of SAS cell xenografts on nude mice. The reduced expression of oncogenic miRNAs in vivo aligned with in vitro findings. In conclusion, our study indicates that CAP jet treatment diminishes OSCC cell viability by abrogating survival signals and oncogenic miRNA expression.

The effects of various drawing parameters and annealing processes on the structure and properties of Cu-Ag wires, containing 1 wt% silver, were investigated using specialized equipment including fine wire drawing machines, very fine wire drawing machines, heat treatment equipment, tensile testing machines, microcomputer-controlled electronic universal testers, resistance testers, and scanning electron microscopes. The results revealed that continuous drawing of Cu-1%Ag alloy wires led to elongation of the grains, resulting in a uniform and tightly fibrous microstructure. Moreover, the tensile strength of the alloy wire increased from 670 MPa to 783.9 MPa after a single-pass with a deformation of 14%. Subsequently, when the wire was drawn at a speed of 500 m/min, the tensile strength further increased to 820.1 MPa. After annealing the Փ0.08 mm Cu-1% Ag alloy wire, an increase in annealing temperature up to 500°C resulted in the wire's tensile strength decreasing from 820.1 MPa to 377.5 MPa. Simultaneously, the elongation increased from 1.94% to 15.21%, and the resistivity decreased from 1.931×10-8Ω·m to 1.723×10-8Ω·m. Additionally, when annealing was conducted at a rate of 80 m/min, the wire resistivity dropped to 1.635×10-8Ω·m.

The cold-pressed hempseed oil (HO) has been increasingly exploited in human diet for its excellent nutritional and healthy properties. However, it has a high content of polyunsaturated fatty acids (PUFAs) and chlorophylls, which inevitably accelerate its oxidative deterioration, especially in presence of light. In this scenario, the filtration technology may ameliorate the oxidative stability of the oil, with positive effects on its nutritional quality and shelf-life. Therefore, in this study, the oxidative stability and minor compounds of non-filtered and filtered HO (NF-HO and F-HO) were monitored over 12 weeks of storage in transparent glass bottles. F-HO showed a better hydrolytic and oxidative status than NF-HO during storage. As a result, F-HO displayed also a better preservation of total MUFA and PUFA in the autoxidation process. Filtration consistently reduced chlorophylls, thus, causing a variation of the natural color of HO. Accordingly, F-HO not only revealed an increased resistance to photooxidation but was also suitable for storage in clear bottles within 12 weeks. F-HO predictably showed lower carotenoids, tocopherols, polyphenols, and squalene compared to NF-HO. However, filtration appeared to play a “protective role” toward these antioxidants, which had lower degradation rates in F-HO than NF-HO for 12 weeks. Interestingly, the element profile of HO was not affected by filtration and remained stable during the study period. Overall, this study may be of practical use to both producers and marketers of cold-pressed HO.

Impact of the Corona, dielectric barrier discharge and low pressure radiofrequency air plasmas on the chemical composition and wettability of the medical grade polyvinylchloride was investigated. Corona plasma treatment exerted the most pronounced increase in the hydrophilization of polyvinylchloride. The specific energy of adhesion of the pristine and plasma treated PVC tubing is reported. The kinetics of hydrophobic recovery following the plasma treatment was explored. The time evolution of the apparent contact angle under the hydrophobic recovery is satisfactorily described by the exponential fitting. Energy-dispersive X-ray spectroscopy of the chemical composition of the near-surface layers of the plasma treated catheters revealed their oxidation. The effect of the hydrophobic recovery is hardly correlated with oxidation of the polymer surface, which is irreversible.

One of the major sources of catastrophic failures and deterioration of the mechanical properties of metals such as ductility, toughness, and strength, of various engineering components during application is hydrogen embrittlement (HE). It occurs as a result of adsorption, diffusion, and interaction of hydrogen with various metal defects like dislocations, voids, grain boundaries and oxide/matrix interfaces due to its small atomic size. Over the years, extensive effort has been dedicated to understanding hydrogen embrittlement sources, effects, and mechanisms. This research aimed at assessing the tensile properties; toughness, ductility, and susceptibility to hydrogen embrittlement, of cold-finished mild steel. Steel coupons were subjected to electrochemical hydrogen charging in a carefully chosen alkaline solution over a particular time and at various charging current densities. Tensile property tests were conducted immediately post the charging process, and the results were compared with those of uncharged steel. The findings revealed a clear drop in toughness and ductility with increasing hydrogen content. Fracture surfaces were examined to determine failure mechanisms. This evaluation has enabled the prediction of the steel's ability to withstand environments with elevated hydrogen concentrations during practical applications.