A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

The physical properties of a structure such stiffness although can be determined by some statical tests, the identification of damping parameter requires a dynamic test. In general, both theoretical prediction and experimental identification of damping are quite difficult. There are many different techniques available for damping identification, and each method gives a different damping parameter. The dynamic indentation method, rheometry, atomic force microscopy, and resonant vibration tests are commonly used to identify the damping of materials, including soft materials. While the viscous damping ratio, loss factor, complex modulus and viscosity are quite common to describe damping of materials, there are also other parameters such as the specific damping capacity, loss angle, half-power bandwidth, and logarithmic decrement to describe damping of various materials. Often one of these parameters is measured in practical applications and the measured damping parameter needs to be converted into another damping parameter for comparison purposes. In this review, the theoretical derivations of different parameters for the description and quantification of damping and their relationships, and the methods for damping identification are presented. The expressions for both high damping and low damping are included and evaluated. This paper could be a primary resource for damping research and teaching.

Relationship between the results of penile duplex doppler ultrasound (PDDU) and response to vardenafil was investigated in patients diagnosed with erectile dysfunction (ED). Data of 148 patients with ED were analysed retrospectively. Patients who did not respond to therapy were classified as Group I (n = 32), those responded partially were classified as Group II (n = 40) and complete responders were classified as Group III (n = 76). Age, comorbid diseases, vascular and penile pathology were compared among the three groups. While diabetes mellitus (DM) and dyslipedimia positivity adversely affect the response to treatment, the presence of hypertension (HT), peyronie's disease and priapism increase the therapeutic response to the treatment (p < 0.05). Arterial insufficiency was present in 20(30.3%), 25(37,9%) and 21(31.8%) of the patients in Group I, Group II and Group III, respectively (p = 0.001). Venous insufficiency was observed in 3(14.3%) patients in Group I and in 8(85.7%) patients in Group III (p = 0.001). Arterial/venous insufficiency was seen in 9(30%), 14(46.7%) and 7(23.3%) of the patients in Group I, Group II and Group III, respectively (p = 0.001). Response rate to treatment was highest in normal patients according to PDDU, followed by patients with venous insuffiency. Besides, it was found that DM decreased the response to treatment, whereas response was increased in cases with HT, priapism and Peyronie’s disease.

Late onset Pompe disease is a recessive lysosomal storage disease. Clinical features include skeletal muscles deficiency and diaphragm weakness. Clinical management relies on supportive treatment and mechanical ventilation in patents with chronic respiratory failure. M mode ultrasound and tissue Doppler imaging can be used to assess and to follow up diaphragm function.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

This paper presents a theory on graph topological structure and graph coloring, proving that for any N-order graph structure (with a topological structure similar to ), the maximum number of colors required for coloring is less than or equal to . The Four Color Theorem is just one special case of this theory, with the maximum structure size for a four-color graph being a 4-order structure graph, hence requiring only a maximum of 4 colors for coloring.

Background: In this study, we aimed to evaluate the effect of s-FLT-1 and PlGF concentrations in women in the first trimester of pregnancy on the pulsatility index of the ductus venosus and the right and left uterine arteries. Methods: A total of 108 pregnant women in their first trimester were included in the study, with 87 assigned to the experimental group and 21 to the control group. Ultrasound examination were performed to measure the uterine artery pulsatility index, resistance index, ductus venosus pulsatility index, and blood sampling levels of biomarkers such as b-HCG; PAPP-A; s-FLT-1 and PlGF. Results: There was a significant negative relationship between PAPP-A concentration and the risk of fetal growth restriction, and a significant negative relationship between PlGF concentration and the risk of preeclampsia and fetal growth restriction in women in their first trimester of pregnancy. There was also a significant positive relationship between sFLT-1/PLGF ratio and the risk of developing preeclampsia. No significant relationships were found between the concentrations of biomarkers beta-HCG, PAPP-A, sFLT-1, PlGF, and any of the parameters PIUARt, PIUALt, Mean uterine arteries, and DVPI. Summary: In conclusion, this study did not find conclusive evidence to support the hypothesis that beta-HCG, PAPP-A, s-FLT-1, and PlGF concentrations in women in the first trimester of pregnancy have a significant effect on the Pulsatility Index of the ductus venosus and the Right and left Uterine Arteries. Further research is needed to investigate these potential associations.

The tumor microenvironment is known to have increased levels of cytokines and metabolites, such as glutamate, due to their release from the surrounding cells. A normal cell around the tumor that responds to the inflammatory environment is likely to be subsequently altered. We will discuss how these abnormalities will support tumor survival via the actions of gap junctions (GJs) and hemichannels (HCs) which are composed of hexamer of connexin 43 (Cx43) protein. In particular, we will discuss how GJ intercellular communication (GJIC) in glioma cells, the primary brain tumor, is a regulatory factor and its attenuation leads to tumor invasion. In contrast, the astrocytes, which are normal cells around the glioma, are "hijacked" by tumor cells, either by receiving the transmission of malignant substances from the cancer cells via GJIC, or perhaps via astrocytic HC activity through the paracrine signaling which enable the delivery of these substances to the distal astrocytes. This astrocytic signaling would promote tumor expansion in the brain. In addition, brain metastasis from peripheral tissues has also been known to be facilitated by GJs formed between cerebral vascular endothelial cells and cancer cells. Astrocytes and microglia are generally thought to eliminate cancer cells at the blood brain barrier. In contrast, some reports suggest they facilitate tumor progression as tumor cells take advantage of the normal functions of astrocytes that support the survival of the neurons by exchanging nutrients and metabolites. In summary, GJIC is essential for the normal physiological function of growth and allowing the diffusion of physiological substances. Therefore, whether GJIC is cancer promoting or suppressing may be dependent by what permeates through GJs, when it is active, and to which cells. The nature of GJs, which has been ambiguous in brain tumor progression, will need to be re-visited and understood together with new findings on Cx proteins and HC activities.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

Traditional diagnosis of patent foramen ovale (PFO) in the heart has involved the use of transcranial doppler (TCD). However, TCD is essentially a blind test that cannot directly visualize the location of blood vessels. Since TCD relies on qualitative assessments by examiners, there is room for errors, such as misalignment of the ultrasound's angle of incidence with the actual blood vessels. This limitation affects the reproducibility and consistency of the examination. In this study, we presented an alternative approach for assessing right-to-left shunt (RLS) associated with PFO using contrast transcranial color-coded doppler (C-TCCD) with bubble contrast. The patient under consideration had been diagnosed with an ischemic stroke through imaging, but the subsequent cardiac work-up failed to determine the cause. Employing C-TCCD for RLS screening revealed a confirmed RLS of Spencer’s three grades. Subsequently, transesophageal echocardiography (TEE) was conducted to evaluate PFO risk factors, confirming an 8 mm PFO size, a 21 mm tunnel length, a hypermobile interatrial septum, and persistent RLS. The calculated high-risk PFO score was 4 points, categorizing it as a very high-risk PFO. This case underscores the importance of C-TCCD screening in detecting RLS associated with PFO, especially in cryptogenic stroke patients when identifying the underlying cause of ischemic stroke becomes challenging.

The reasons for the circular sense of human color perception generated by two sorts of color opponent neurons and three cone types are not well understood. Here we use geometrical analysis to examine the hypothesis that opponency, the recursive nature of color perception, and trichromacy arise as the most efficient ways of distinguishing spectrally different points on a plane using a minimum of color classes and receptor types.

Cystic echinococcosis (CE), caused by the larval stage of Echinococcus granulosus, is significantly underreported in Mongolia due to geographical remoteness, lack of early diagnostics, and poor clinical management. This study aimed to provide a more accurate estimate of CE in Mongolia by comparing data of surgical (reported) and diagnosed (unreported) cases, and assessing the challenges faced by rural doctors in disease management and surveillance. We collected data on surgical cases hospitalized between 2006-2016 and newly diagnosed CE cases in 2016 from eight provinces. Using a quasi-Poisson regression model of the collected data, we used extrapolation to estimate the number of diagnosed cases for the entire country. Additionally, fourty health professionals from all 21 provinces rated local clinical management for CE through a questionnaire. Results reveal that surgical cases (2.2 per year) represent only one-eighth of diagnosed cases (15.9 per year). The laboratory facilities, disease reporting, and cyst classification usage scored below 2. These results highlight the significant underreporting of CE in Mongolia and urges human and animal health experts, along with policymakers, to invest into combating CE, particularly in remote provincial areas. It also emphasizes the need for standard clinical management involving cyst classification according to WHO-IWGE, seamless integration of CE reporting and monitoring mechanisms, which can significantly contribute to the national and global burden estimation of CE.

The Range–Doppler (R-D) model is extensively employed for the geometric processing of Synthetic Aperture Radar (SAR) images. Refining the sensor motion state and imaging parameters is the most common method for achieving high-precision geometric processing using the R-D model, comprising a process that involves numerous parameters and complex computations. In this study, we introduce a novel approach to improve the positioning accuracy of the R-D model, implementing a low-order polynomial to compensate for the original imaging errors without altering the initial positioning parameters. We also design low-order polynomial compensation models with different parameters. The models are evaluated on various SAR images from different platforms and bands, including spaceborne TerraSAR-X and GF3-C images, manned airborne SAR-X images, and unmanned aerial vehicle-mounted miniSAR-Ku images. Furthermore, image positioning experiments involving the use of different polynomial compensation models and various numbers and distributions of Ground Control Points (GCPs) are conducted. The experimental results demonstrate that geometric processing accuracy comparable to that of the classical rigorous positioning method can be achieved even when applying only an affine transformation model to the images. Compared to classical refinement models, however, the proposed image-compensated R-D model is much simpler and easy to implement. Thus, this study provides a convenient, robust, and widely applicable method for the geometric positioning processing of SAR images, offering a potential approach for the joint-positioning processing of multi-source SAR images.

We propose a novel unsupervised semantic segmentation method for fast and accurate flood area detection utilizing color images acquired from Unmanned Aerial Vehicles (UAVs). To the best of our knowledge, this is the first fully unsupervised method for flood area segmentation in color images captured by UAVs, without the need of pre-disaster images. The proposed framework addresses the problem of flood segmentation based on parameter-free calculated masks and unsupervised image analysis techniques. First, a fully unsupervised algorithm gradually excludes areas classified as non-flood utilizing calculated masks over each component of the LAB colorspace, as well an RGB vegetation index and the detected edges of the original image. Unsupervised image analysis techniques, such as distance transform, are then applied, producing a probability map for the location of flooded areas. Finally, flood detection is obtained by applying the hysteresis thresholding segmentation. The proposed method is tested and compared with variations, and other supervised methods in two public datasets, consisting of 953 color images in total, yielding high-performance results, with 87.4% and 80.9% overall accuracy and F1-Score, respectively. The results and computational efficiency of the proposed method show that it is suitable for on board data execution and decision-making during UAVs flight.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

This study introduces a data obfuscation technique, leveraging the exponential map associated with the generators of Lie groups. Originating from quantum machine learning frameworks, our method illustrates the practical application of quantum mechanics principles in data processing. Specifically, it employs the exponential map of a generator algebra to introduce controlled noise into the data, achieving obfuscated data while preserving its utility for machine learning tasks. This strategy is shown to safeguard privacy in sensitive datasets, such as discussed medical records, and to enhance dataset volume and diversity through augmentation. Our empirical analysis, benchmarked against standard machine learning approaches, demonstrates that our method can maintain or even improve the predictive accuracy of the original data. This research highlights the potential of Lie group theory for advancing data privacy in medicine, marking a significant contribution to machine learning methodologies by offering the dual benefits of data obfuscation and enrichment. Through this synthesis of algebraic structures and machine learning, we propose new pathways for the secure and effective use of data in sensitive areas.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

Abstract: Doppler renal resistive index (RRI) has been used for several decades as a potential indi-cator for renal disease and progression. In recent years, RRI has emerged as a useful prognostic indicator for a range of co-morbidities in patients who are acutely unwell and as a potential marker for sub-clinical acute kidney injury (AKI) and post procedural AKI risk. Despite this, the clinical and theoretical determinants of RRI are poorly understood and remain contentious. Method: A narrative review of studies exploring the theoretical, experimental, and clinical evidence for factors affecting RRI. No date restrictions were set. Findings: Both experimental and clinical data confirm that RRI is markedly affected by a range of systemic and renal determinants and is influenced closely by the underlying risk factors and sys-temic vascular changes that lead to progressive renal damage. Discussion: This paper provides an overview of the key haemodynamic determinants of renal re-sistive index and aims to clarify their relative importance. With reference to a simplified theoretical model, evidence from experimental and clinical studies is reviewed. Pathophysiological factors and patient characteristics that influence RRI are explored to provide a better understanding of why RRI values change in the presence of common or complex pathologies. Conclusion: By gaining a better understanding of the complex systemic and renal factors that influ-ence RRI, ultrasound users will be better prepared to understand and interpret changes in RRI across a range of patient presentations.

Tissue Doppler Imaging (TDI) is a non-invasive, echocardiographic imaging technique that measures myocardial motion velocity throughout the cardiac cycle using Doppler principles. While conventional Doppler techniques assess blood flow velocity by sensing high-frequency, low amplitude signals from small, fast-moving blood cells, TDI uses the same Doppler principles to instead measure high-amplitude, lower-velocity signals of myocardial tissue. Methods A literature review was conducted to survey and review studies investigating the limitations, strengths, physical principles, novel methods, applications in diseased states, and prognostic capabilities of TDI. These articles were further screened for inclusion, and those deemed ineligible or irrelevant to the scope of the review were discarded. In total, 19 studies were included in the qualitative synthesis. Results TDI is shown to be an effective method for detailed quantification of cardiac function. It provides an early means of diagnosing cardiac dysfunction and is a valid prognostic indicator for various forms of heart disease. TDI's versatility and precision allows clinicians to predict the clinical course of disease, leading to early intervention and the selection of targeted care management plans for many cardiac pathologies. Despite imaging limitations like angle dependence and incapacity for passive and active motion differentiation, further investigation continues to reveal novel TDI methodologies that advance the scope of this imaging technique.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

Airborne Frequency Diversity Array (FDA) radar operating at a high pulse repetition frequency encounters severe range-ambiguous clutter. The slight frequency increments introduced by the FDA result in angle and range coupling. Under these conditions, conventional space-time adaptive processing (STAP) often exhibits diminished performance or fails, complicating target detection. This paper proposes a method combining elevation oblique subspace projection with azimuth-Doppler STAP to suppress range-ambiguous clutter. By analyzing the relationship between elevation frequency and range, the proposed method compensates for quadratic range dependence. Through the construction of an elevation oblique subspace projection technique, an elevation adaptive filter is used to separate clutter from ambiguous regions. Residual clutter suppression is achieved through azimuth-Doppler STAP, enhancing target detection performance. Simulation results demonstrate that the proposed method effectively addresses range dependence and ambiguity issues, improving target detection performance in complex airborne FDA radar environments.

Stable isotope-assisted approaches can improve untargeted LC-HRMS metabolomics studies. Here, we demonstrate at the example of chemically stressed wheat that metabolome-wide internal standardization by globally 13C-labeled metabolite extract (GLMe-IS) of experimental-condition-matched biological samples can help to improve coverage of treatment-relevant metabolites and aid in the post-acquisition assessment of putative matrix effects in samples obtained upon different treatments. For this, native extracts of toxin- and mock-treated (control) wheat ears were standardized by the addition of uniformly-13C-labeled wheat ear extracts that were cultivated under similar experimental conditions (toxin-treatment and control) and measured with LC-HRMS. The results show that 996 wheat-derived metabolites were detected with the non-condition-matched 13C-labeled metabolite extract, while another 68 were only covered by the experimental-condition-matched GLMe-IS. Additional testing is performed with the assumption that GLMe-IS enables compensation for matrix effects. Although on average no severe matrix differences between both experimental conditions were found, individual metabolites may be affected as is demonstrated by wrong decisions with respect to the classification of significantly altered metabolites. When GLMe-IS was applied to compensate for matrix effects, 272 metabolites showed significantly altered levels between treated and control samples, 42 of which would not have been classified as such without GLMe-IS.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

Endoscopic ultrasound (EUS) and intraductal ultrasound (IDUS) play very important roles in the field of biliary tract disease. Because of their excellent spatial resolution, the detection of small lesions and T-staging of tumors have become possible. Additionally, contrast-enhanced EUS and the new imaging technique of detective flow imaging are reported to be useful for differential diagnosis. Furthermore, EUS-guided tissue acquisition is used not only for pathological diagnosis, but also to collect tissue samples for cancer genome profiling. Although percutaneous transhepatic biliary drainage (PTBD) was traditionally performed in cases where endoscopic retrograde cholangiopancreatography is not feasible, treatments using EUS have recently become increasingly common, and EUS-guided biliary drainage was recently suggested to be superior to PTBD in terms of a higher success rate, less adverse events, and lower reintervention rate. This review provides an overview of diagnosis and treatment utilizing the features and techniques of EUS and IDUS.

Pencil-beam Doppler scatterometers are a promising remote sensing tool for measuring ocean vector winds and currents from space. While several point designs exist in the literature, these designs have been constrained by the hardware they inherited, and the design is sub-optimal. Here, I present guidelines to optimize the design of these instruments starting from the basic sensitivity equations. Unlike conventional scatterometers or pencil-beam imagers, appropriate sampling of the Doppler spectrum and optimizing the radial velocity error lead naturally to a design that incorporates a pulse-to-pulse separation and pulse length that vary with scan angle. Including this variation can improve radial velocity performance significantly and the optimal selection of system timing and bandwidth is derived. Following this, optimization of the performance based on frequency, incidence angle, antenna length, and spatial sampling strategy are considered. It is shown that antenna length influences the performance most strongly, while the errors depend only on the square root of the transmit transmit power. Finally, a set of example designs and associated performance are presented.

Observed sea surface Ka-band normalized radar backscatter cross section (NRCS) and Doppler velocity (DV) exhibit energy at low frequencies (LF) below the surface wave range. It is shown that non-linearity in NRCS-wave slope Modulation Transfer Function (MTF) and inherent NRCS averaging within the footprint account for the NRCS and DV LF variance with the exception of VV NRCS for which almost half of the LF variance is attributable to wind fluctuations. Although the distribution of radar DV is quasi-Gaussian suggesting virtually little impact of non-linearity, the LF DV variations arise due to footprint averaging of correlated local DV and non-linear NRCS. Numerical simulations demonstrate that MTF non-linearity weakly affects traditional linear MTF estimate (less than 10% for |MTF|< 20). Thus the linear MTF is a good approximation to evaluate the DV averaged over large footprints typical of satellite observations.

The continued success of any conventional sweet potato breeding program is limited to knowledge of the inheritance of the traits studied, such as flesh color and tuberous root shape, because it is difficult to fractionate color frequencies by visual separation. The objective was to understand the mode of inheritance of these genetic traits. The crossing blocks were established at the Research Institute of Tropical Roots and Tuber Crops (INIVIT-Cuba). Eight parental genotypes of known compatibility were selected, with contrasting phenotypic characteristics to develop seg-regating populations. To express color objectively, the CIE L*a*b* color space was used (L*: lumi-nosity; a* and b*: chromatic coordinates), in addition, four morphometric variables associated with the shape and dimensions of the tuberous roots were evaluated. From 2419 reciprocal cross-es, 2045 botanical seeds and 1764 seedlings were obtained. Incomplete dominance of the white and purple flesh colors over the orange color was observed, as well as transgressive segregation for purple, orange and white flesh colours, and for the shape of the tuberous roots. The results al-lowed to propose a genetic model of biparental crosses to improve the flesh color of I. batatas, as well as a predictive formula of the progenies to be selected.

Background: Bariatric surgery (BS) has a significant impact on body composition (BC) and con-sequently may affect established sarcopenic obesity (SO) in candidate patients. The aim of this study is to assess the utility of muscle ultrasound (MUS) of rectus femoris thickness (RFT) for the evalua-tion of BC and skeletal muscle function in patients undergoing BS compared to bioimpedance analysis (BIA), dual-energy X-ray absorptiometry (DEXA) and dynamometry. On the other hand, we aim to demonstrate how MUS of RFT correlates better with the quality of life (Qol) in this population, likely because it enables the detection of regional quadriceps muscle sarcopenia, in comparison to the other mentioned methods. Methods: This is a prospective pilot study including 77 subjects (64.9% female, mean age: 53.2 ± 8.67 years) who underwent BS. Handgrip strength was measured using a dynamometer, fat-free mass index (iFFM) was assessed by BIA, appendicular muscle index (AMI) was calculated using DEXA and RFT was measured by MUS. Moreover, Homeostasis Model Assessment of Insulin Resintance (HOMA-IR) was calculated. All these measurements were conducted 1 month prior to BS and at the 12-month follow-up. QoL was as-sessed using the Moorehead-Ardelt questionnaire. Results: The mean BMI decreased by 12.95 ± 3.56 kg/m2 (p=0.001). Firstly, we observed positive correlation pre-surgery between HOMA and: RFT (r=0.27, p=0.02), iFFM (r=0.36, p=0.001), AMI (r=0.31, p=0.01) and dynamometer (r=0.26, p=0.02). In addition, we found correlation between RFT and iFFM (pre-surgical: r=0.31, p=0.01; post-surgical: r=0.25, p=0.05) and between RFT and lower extremities AMI post-surgical (r=0.27, p=0.04). Secondly, we observed significant reductions in iFFM, AMI and RFT (p=0.001), but not with dynamometer (p=0.94). Finally, a tendency to a positive correlation between QoL question-naire and RFT post-surgery (r=0.23, p=0.079) was observed. Conclusions: Our results suggest that RFT measured by MUS for the evaluation of SO and the follow-up after BS of these patients. Moreover, RFT can provide relevant information about regional sarcopenia and probably has an accurate correlation with QoL in comparison with the other methods.

Magnetomotive ultrasound (MMUS) is a promising imaging modality for detecting magnetic nanoparticles. In MMUS, an external oscillating magnetic field induces motion of the injected magnetic nanoparticles within tissue, and phase-based tracking algorithms are used to detect the motion. However, the subwavelength scale of theses displacements (often a few micrometers) makes direct visualization on conventional ultrasound B-mode images impossible. In this work, we adapt the Eulerian motion magnification technique to create a novel ultrasound display mode for identifying the nanoparticle locations, eliminating the need for displacement tracking algorithms. Phantom and in-vivo experiments demonstrate that our technique successfully magnifies magnetomotion and the associated shear wave propagation in ultrasound B-mode imaging and pinpoints the nanoparticle vibration source, even in low-concentration scenarios. Additionally, motion magnification magnified the displacement of nanoparticles, having the potential to improve the localization accuracy of displacement tracking algorithms in MMUS.

We are introducing a highly efficient 48-channel ultrasound beamforming system ideal for ultrasound endoscopy applications. The system includes a transmitter and a receiver, which allow for low-area, high-resolution imaging acquisition. The transmitter uses a charge redistribution HV (high voltage) scheme to generate three-level pulses that actuate the transducer, implemented with the standard CMOS process for optimal cost and power savings. Meanwhile, the receiver features a sub-array structure and a delay generator that reduces area usage. To achieve high-resolution ultrasound imaging acquisition with low computational power, we developed the Shift Coherence Factor (SCF) algorithm, which is hardware-friendly. This approach delivers a lateral resolution over 20% better than the conventional delay and sum (DAS) algorithm, with a contrast ratio of over 30 dB. The system was implemented in a 180 nm standard CMOS process with an area of 24.98 mm2, power consumption of 8.23 mW per channel, achieving a delay resolution of 8.33 ns, and a low-area implementation of 0.52 mm2 per channel. The system offers high-quality imaging acquisition with minimal additional area and power consumption, which has great potential for 3D imaging or catheterized ultrasound systems.

Whey protein was pretreated with multi-frequency ultrasound in mono, dual, and tri-frequency modes. The effect of multi-frequency ultrasound pretreatment on the hardness, chemical forces, and microstructure of acid-induced whey protein gel was investigated. Whey protein gels pretreated with dual and tri-frequency ultrasound showed higher hardness (p3.35 mm) in those samples were resisted to gastric digestion. Moreover, the tri-frequency ultrasound pretreatment of whey protein gel released the least free amino group during gastric digestion. In contrast, whey protein gel with the mono-frequency ultrasound pretreatment released the highest amount of free amino acid group during intestinal digestion. Findings from this study suggested that gel hardness and network density could modulate the digestion behaviors of protein gels.

The relativistic Doppler effect comes from the fact that observers in different inertial reference frames experience space and time differently, while the speed of light remains always the same. Consequently, a wave packet of light exhibits different frequencies, wavelengths, and amplitudes. In this paper, we present a local approach to the relativistic Doppler effect based on relativity, spatial and time translational symmetries, and energy conservation. Afterward, we investigate the implications of the relativistic Doppler effect for the quantum state transformations of wave packets of light and show that a local photon is a local photon at the same point in the spacetime diagram in all inertial frames.

The article aims to present the possible use of the simple modified optical training kit as a low-cost, simple setup for high precision surface speed measurements. A measurement capability evaluation of the optical Doppler kit used for velocimetry of a fast-rotating reflecting surface is presented. To get high repeatability measurements, we modified a fibre optic interferometry training kit. By using signal processing and statistics a precision under repeatability conditions of measurements was evaluated. Expressed by the standard deviations (3σ’s) the surface velocity measurements precision below 0.2 m/s is shown. The Cg’s capability indices were also evaluated. We postulate, the electric circuit stability of the measurement system power supply is essential for a signal noise reducing process for a wide range of metrology systems. It is crucial for precision measurements.

A machine learning method for classifying Lung UltraSound is here proposed to pro- vide a point of care tool for supporting a safe, fast and accurate diagnosis, that can also be useful during a pandemic like as SARS-CoV-2. Given the advantages (e.g. safety, rapidity, portability, cost-effectiveness) provided by the ultrasound technology over other methods (e.g. X-ray, computer tomography, magnetic resonance imaging), our method was validated on the largest LUS public dataset. Focusing on both accuracy and efficiency, our solution is based on an efficient adaptive ensembling of two EfficientNet-b0 models reaching 100% of accuracy, which, to our knowledge, outperforms the previous state-of-the-art. The complexity of this solution keeps the number of parameters in the same order as an EfficientNet-b0 by adopting specific design choices that are adaptive ensembling with a combination layer, ensembling performed on the deep features, minimal ensemble only two weak models. Moreover, a visual analysis of the saliency maps on sample images of all the classes of the dataset reveals where the focus is on an inaccurate weak model versus an accurate model.

This paper presents a simple and streamlined compensation technique for improving the quality of Synthetic Aperture Radar (SAR) images based on the Range Doppler Algorithm (RDA). Incorrect Doppler estimation in space orbit, caused by unexpected radar motion errors, orbit mismatches, and other factors, can significantly degrade SAR image quality. These inaccuracies result in mismatches between the azimuth-matched filter and the received Doppler chirp signal. To address this issue, we propose a Doppler estimation method that leverages the Fractional Fourier Transform (FrFT) and cross-correlation techniques. The received signals are compared with the azimuth-matched filter based on the rotation angle in the FrFT domain, and the Doppler centroid is adjusted to achieve optimal alignment. This process ensures high correlation values and enhanced resolution in the final SAR image. The efficacy of the proposed technique is validated through experiments using real spaceborne SAR data from the practical satellite. The results demonstrate significant improvements in image quality and resolution compared to conventional algorithms, highlighting the advantages of our approach for various remote sensing applications.

Maxwell's equations accurately describe the propagation of electromagnetic (EM) waves. However, the conventional formulation implies invariance to observers, posing challenges in explaining how the wave is perceived by different observers. For example, Doppler effect shows that observers perceive the same EM wave differently.By employing mathematical transformations, we derive a general form of Maxwell’s wave equations by incorporating a "time scaling" factor to account for observer perception. The original form is shown to be a special case when static. The Doppler effect and Sagnac effect are directly derived from Maxwell’s equations. All the results are consistent with established experiments.Our findings offer a fresh perspective, promising a deeper understanding and unification of EM phenomena. We extend Maxwell’s equations to describe not only the propagation of an EM wave, but also how it will be measured by different observers, say, antennas.

The COVID-19 pandemic has affected millions of people globally, with respiratory organs being strongly affected in individuals with comorbidities. Medical imaging-based diagnosis and prognosis have become increasingly popular in clinical settings to detect COVID-19 lung infections. Among various medical imaging modalities, ultrasound stands out as low-cost, mobile, and radiation-safe imaging technology. In this comprehensive review, we focus on ultrasound-based AI studies for COVID-19 detection that use public or private lung ultrasound datasets. We surveyed articles that used publicly available lung ultrasound datasets for COVID-19 and reviewed publicly available datasets and organize ultrasound-based AI studies per dataset. We analyzed and tabulated studies in several dimensions, such as data preprocessing, AI models, cross-validation, and evaluation criteria. In total, we reviewed 42 articles, where 28 articles used public datasets, and the rest used private data. Our findings suggest that ultrasound-based AI studies for the detection of COVID-19 have great potential for clinical use, especially for children and pregnant women. Our review also provides a useful summary for future researchers and clinicians who may be interested in the field.

This paper presents computer and color vision research focusing on human color perception in VR environments. A VR art gallery with digital twins of original artworks is created for this experiment. In this research, the field of colorimetry and the application of CMYK and RGB color models are applied. The interrelationships of the two colors models are applied to create a color modification of the VR art gallery environment using C# Script procedures. This color-edited VR environment works with a smooth change of color tone in a given time interval. At the same time, a sudden change in the color of the RGB environment is defined in this interval. This experiment aims to record a user's reaction embedded in a VR environment and the effect of color changes on human perception in a VR environment. The research uses lie detector sensors that record the physiological changes of the user embedded in VR. Five sensors are used to record the signal. An experiment on the influence of the user's color perception in a VR environment using lie detector sensors has never been conducted. This research defines the basic methodology for analyzing and evaluating the recorded signals from the lie detector. The presented text thus provides a basis for further research in the field of colors and human color vision in a VR environment and lays an objective basis for use in many scientific and commercial areas.

This paper presents an Edge-based color image segmentation derived from the method of Particle Motion in a Vector Image Fields (PMVIF) that could previously be applied only to monochrome images. Instead of using an edge vector field derived from a gradient vector field and a normal compressive vector field derived from a Laplacian-gradient vector field, two novel orthogonal vector fields, directly computed from a color image, one parallel and another orthogonal to the edges, were used in the model to force a particle to move along the object edges. The normal compressive vector field is derived from the center-to-centroid vectors of local color distance images. Next, the edge vector field is derived by taking the normal compressive vector field, multiplied by differences of auxiliary image pixels to obtain a vector field analogous to a Hamiltonian gradient vector field. Using the PASCAL Visual Object Classes Challenge 2012 (VOC2012) and the Berkeley Segmentation Data Set and Benchmarks 500 (BSDS500), the benchmark score of the proposed method is provided in comparison with those of the traditional PMVIF, Watershed, SLIC, K-means, Mean shift, and JSEG. The proposed method yields better RI, GCE, NVI, BDE, Dice coefficients, faster computation time, and noise resistance.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

Background: This study was designed to adapt the Delis-Kaplan Executive System (D-KEFS) version of the Color-Word Interference (CWIT) and Trail making Tests (TMT) in Greek adult population from 20 to 49 years old, since it is of research as well as clinical importance to detect executive functions’ impairment in young adults with neurological or/and psychiatric conditions. Aims: Norms for the Greek adult population have been calculated to be available for neuropsychologists and health professionals who work in relevant settings. Methods: The study sample consisted of 101 healthy adults (41% male and 60% female), aged 20 to 49 years (M=32.16, SD=11.57) with education from 12 to 19 years of schooling (M=14.51, SD= .89). Pearson correlation test as well as chi square test were conducted to examine potential associations between gender, age, education, and participants’ performance. Afterwards, we calculated normative data using raw scores and transformed them to percentile scores. Finally, Greek norms were compared to the original raw scores, which were transformed in scaled scores by Delis et al. (2001). Results: The findings showed that age was the only variable which affected CWIT, whereas level of education as well as age were predictive factors for most TMT conditions, except for the visual scanning test (Condition 1). Gender did not affect both tests. Finally, D-KEFS norms for CWIT and TMT are available for Greek adult population to help clinicians detect executive functions’ deficits and therefore adjust tailored therapeutic strategies. Additionally, it is of great importance to use these tests for research purposes. Conclusion: Given that executive functions are assumed as high- level skills, which are highly related to everyday functionality, adapted tests contribute not only to assess the progression of any existing neurological as well as psychiatric disorders, but they can also be used to evaluate patients’ ability to live independently, as well as their access to work.

Ultrasound imaging is a vital imaging tool in musculoskeletal medicine, with the number of publications on ultrasound-guided surgery increasing in recent years. However, ultrasound imaging has drawbacks, such as operator dependency and image obscurity. Artificial Intelligence (AI) and Deep Learning (DL), a subset of AI, can address these issues. DL methods, including segmentation, detection, and localization of target tissues and medical instruments, potentially allow physicians and surgeons to perform ultrasound-guided procedures more accurately and efficiently. This review summarizes recent advances in ultrasound-guided procedures for musculoskeletal diseases and provides a comprehensive overview of the utilization of AI/DL in ultrasound for musculoskeletal medicine, particularly focusing on ultrasound-guided surgery.

Idiopathic acute pancreatitis (IAP) presents a diagnostic challenge and refers to cases where the cause of acute pancreatitis remains uncertain despite a comprehensive diagnostic evalua-tion. Endoscopic ultrasound (EUS) has emerged as a valuable tool in the diagnostic workup of IAP. This review explores the pivotal role of EUS in detecting the actual cause of IAP, as-sessing its accuracy, timing, safety, and future technological improvement. Following PRISMA guidelines, 60 pertinent studies were selected and analysed. EUS emerges as a cru-cial diagnostic tool, particularly when conventional imaging fails. It can offer intricate visu-alization of the pancreas, biliary system, and adjacent structures. High accuracy of EUS is evident in detecting the actual causes of IAP such as microlithiasis, small bile duct stones, pancreas divisum, and small pancreatic tumors. Optimal timing for EUS is post-resolution of the acute phase of the disease. EUS, when conducted by experienced endoscopists, it boasts minimal safety concerns, and is crucial to prevent complications. EUS-guided interventions, including fine-needle aspiration, collection drainage, and biopsies, aid in cytological analy-sis. With high diagnostic accuracy, safety, and therapeutic potential, EUS is able to improve patient outcomes when managing IAP. Further refinement of EUS techniques and cost-effectiveness assessment of EUS-guided approaches need to be explored in multicenter prospective studies. This review underscores EUS as a transformative tool in unraveling IAP's enigma and advancing diagnostic and therapeutic strategies.

Conclusions: The quantitative method provides a large-scale overview of the biometry measurements of an entire practice. Image audits can then be focused on sonographers whose measurements are outliers, avoiding the time, complexity, and expense of auditing those whose measurements fall within the expected range. We encourage commercial software developers to include tools in their ultrasound reporting software to facilitate such quantitative review.

(1) Background: adnexal masses during pregnancy detection are increased due to the use of first trimester screening and to advanced maternal age. Although the low risk of malignancy, other risks are associated: torsion, rupture or labour obstruction. Correct diagnosis and management are fundamental to guarantee both maternal and fetal safety. Adnexal masses may be troublesome to classify during pregnancy due to the increase in the uterus volume and to pregnancy-related hormonal changes. Management should be based on ultrasound examination to provide the best treatment. (2) Methods: the aim was to describe the ultrasound features of ovarian masses detected during pregnancy. We evaluated patient’s management, perinatal outcomes and follow-up. (3) Results: our study demonstrated that the management should be guided by an accurate ultrasound examination performed by an expert operator according to standardized techniques. Secondly, our results confirm the data present in the literature: the masses are most frequently benign, ultrasound follow-up is the best management strategy and obstetric outcome is not considerably affected. (4) Conclusions: the management of patients with ovarian masses detected during pregnancy should be based on ultrasound examination and a centralization in referral centers for ovarian masses should be considered.

Endobronchial Ultrasound has been widely used in the lymph node staging of lung tumors and the diagnosis of mediastinal diseases. In the last decades this procedure has evolved in several technical aspects, with new tools available to optimize the tissue sampling and to increase the diagnostic yield, like elastography, different types of needles and, most recently, miniforceps and cryobiopsy. Then, also the indications for EBUS have extended beyond the thoracic boundaries to sample lesions of the liver, left adrenal gland and retroperitoneal lymph nodes via the gastroesophageal tract. In this review we will analyze the actual indication of EBUS, even the more unusual, to underline the multiple use of EBUS in clinical practise.

This study aimed to evaluate the discrepancies between genetic and visual coat color assignment in the Sarcidano Horse and to elucidate potential reasons. Individual DNA from 90 Sarcidano Horses was used for genetic assignment of coat color to explore the correspondence with individual forms containing phenotypical traits. The MC1R exon 1 and ASIP exon 3 have been genotyped and sequenced to obtain a picture of the coat color distribution in this breed. Surprisingly, once we compared the genetic results with the individual forms reporting the phenotypic data for each subject, a certain degree of non-correspondence between the phenotypic and genetic data in relation to coat color emerged. From the genetic analysis, Chestnuts (n = 58) resulted the most common Sarcidano Horse (n = 58), followed by a quite large number of Blacks (n = 28) and a very small number of Bays (n = 4), whereas phenotypic distribution resulted in 38 Chestnuts, 40 Bays, only 2 Blacks, and 10 Grays (without the possibility of recognizing the true color they carried). Chestnut resulted a very representative coat color, while many horses that visually identified as Bays were genetically Blacks. This discrepancy, that could be due to a variety of individual and external factors, including age, time of year, living situation and dietary condition, suggesting the importance of accurate coat color identification to ensure adequate features registration and reliable prediction of offspring’s coat color.

Color plays an important part in human activities, affects circadian cycle and decision making process. Therefore, it is important to investigate human judgment under different color of illumination, especially, because color perception is subjective. In this study, we developed required instrumentation to control the red (R), green (G), Blue (B) and Amber (A) colored light emitting diode (LED) lamp for carrying out Magneto Encephalography (MEG) brain scan. We developed a software to generate all the colors in the visual spectrum, predefined white light combinations and saturation of an illuminated objects by using RGBA color pallet. The lamp is required to control from outside of the MEG electromagnetically shielded room with the LED lamp located inside the MEG room. Hence, USB is used for the communication mode. The feasibility of using LED lamp with MEG brain scanner has been validated for bio-medical and psychological MEG experiments.

Vertebrate color vision is evolutionarily ancient. Jawless fish evolved four main spectral types of cone photoreceptor, almost certainly complemented by retinal circuits to process chromatic opponent signals. Subsequent evolution of photoreceptors and visual pigments are now documented for many vertebrate lineages and species, giving insight into evolutionary variation and ecological adaptation of color vision. We look at organization of the photoreceptor mosaic and the functions different types of cone in teleost fish, primates, and birds and reptiles. By comparison less is known about the underlying neural processing. Here we outline the diversity of vertebrate color vision and summarize our understanding of how spectral information picked up by animal photoreceptor arrays is adapted to natural signals. We then turn to the question of how spectral information is processed in the retina. Here, the quite well known and comparatively ‘simple’ system of mammals such as mice and primates reveals some evolutionarily conserved features such as the mammalian Blue^ON system which compares short and long wavelength receptors signals. We then survey our current understanding of the more complex circuits of fish, amphibians, birds and reptiles. Together, these clades make up more than 90% of vertebrate species, yet we know disturbingly little about their neural circuits for colour vision beyond the photoreceptors. Here, long-standing work on goldfish, freshwater turtles and other species is being complemented by new insights gained from the experimentally amendable retina of zebrafish. From this body of work, one thing is clear: The retinal basis of colour vision in non-mammalian vertebrates is substantially richer compared to mammals: Diverse and complex spectral tunings are established at the level of the cone output via horizontal cell feedforward circuits. From here, zebrafish use cone-selective wiring in bipolar cells to set-up color opponent synaptic layers in the inner retina, which in turn lead a large diversity of color-opponent channels for transmission to the brain. However, while we are starting to build an understanding of the richness of spectral properties in some of these species’ retinal neurons, little is known about inner retinal connectivity and cell-type identify. To gain an understanding of their actual circuits, and thus to build a more generalised understanding of the vertebrate retinal basis of color vision, it will be paramount to expand ongoing efforts in deciphering the retinal circuits of non-mammalian models.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

BACKGROUNDBrain death in most countries requires supplementation of clinical diagnosis with ancillary tests such as EEG, cerebral angiography, or radionuclide imaging. Transcranial Doppler sonography (TCD) is one such non-invasive, real-time, bedside test that sidesteps the logistic hurdles associated with some of the tests mentioned above. OBJECTIVETo substantiate the utility of TCD as a reliable ancillary test to diagnose brain death with more certainty and reliability.METHODOLOGYMeta-analysis was performed with the use of statistical and analytical software to obtain data and estimate Sensitivity, Specificity, positive predictive value(PPV), diagnostic odds ratio (DOR), and relative risk with 95 percent confidence intervals to examine critical clinical outcomes(CI).RESULTSInitial dataset of 31 studies of which 16 studies, with a total of 1317 patients was used considering the reliability of the data. The pooled sensitivity and specificity of TCD were 0.91 (95% CI range: 0.89-0.93) and 0.99 (95% CI range: 0.97-0.99) respectively. The summary of the ROC curve showed an area under the curve of 0.9750 and an overall diagnostic odds ratio (DOR) was 323.26 with the Younden Index being 0.9. Summary of Fagan plot analysis of all studies showed a prior probability of 63% (1.7); a Positive Likelihood Ratio of 56, a post-test probability of 99% (96); a Negative likelihood ratio of 0.09, and a post-test probability of 13% (0.2).CONCLUSIONOur study emphasizes that clinical diagnosis is sufficiently adequate to declare a patient cerebrally dead. However, for ambiguous cases, TCD is a practical and fast method showing close correspondence to angiography and is superior to other bedside tests like EEG.

The origin and climate impact of Arctic aerosols, like the Arctic Haze, are not fully understood. Therefore, long-term aerosol observations in the Arctic are performed. In this study we present a homogenised data set from sun and star photometer operated in the European Arctic, in Ny-Ålesund, Svalbard, from 2004 – 2023. Due to polar day and polar night it is crucial to use observations of both instruments. Their data is evaluated in the same way and follows the cloud-screening procedure of AERONET. Additionally, an improved method for the calibration of the star photometer is presented. We found out, that winter months are generally more polluted and have larger particles than summer. While the monthly median Aerosol Optical Depth (AOD) decreases in spring, the AOD increases significantly in autumn months. The Arctic Haze is not characterised by large particles and can not be distinguished from large aerosols in winter months. With autocorrelation analysis we found out, that AOD events usually occur with duration of several hours and are therefore caused by large-scale processes and may have a periodicity of several days. Local processes can be neglected in Ny-Ålesund but long-range transport plays a major role for the Arctic aerosol budget. We also compared AOD events with large-scale processes, like large-scale oscillation patterns, sea ice, weather conditions or wildfires on the Northern Hemisphere but did not find one single cause, which clearly determines the Arctic AOD.

Ocean surface currents and winds are tightly coupled essential climate variables, and, given their short time scales, observing them at the same time and resolution is of great interest. DopplerScatt is an airborne Ka-band scatterometer that has been developed under NASA's Instrument Incubator Program (IIP) to provide a proof of concept of the feasability of measuring these variables using pencil-beam scanning Doppler scatterometry. In the first half of this paper, we present the Doppler scatterometer measurement and processing principles, paying particular attention to deriving a complete measurement error budget. Although Doppler radars have been used for the estimation of surface currents, pencil-beam Doppler Scatterometry offers challenges and opportunities that require separate treatment. The calibration of the Doppler measurement to remove platform and instrument biases has been a traditional challenge for Doppler systems, and we introduce several new techniques to mitigate these errors when conical scanning is used. The use of Ka-band for airborne Doppler scatterometry measurements is also new, and, in the second half of the paper, we examine the phenomenology of the mapping from radar cross section and radial velocity measurements to winds and surface currents. To this end, we present new Ka-band Geophysical Model Functions (GMF's) for winds and surface currents obtained from multiple airborne campaigns. We find that the wind Ka-band GMF exhibits similar dependence to wind speed as that for Ku-band scatterometers, such as QuikSCAT, albeit with much greater upwind-crosswind modulation. The surface current GMF at Ka-band is significantly different from that at C-band, and, above 4.5 m/s has a weak dependence on wind speed, although still dependent on wind direction. We examine the effects of Bragg-wave modulation by long waves through a Modululation Transfer Function (MTF), and show that the observed surface current dependence on winds is consistent with past Ka-band MTF observations. Finally, we provide a preliminary validation of our geophysical retrievals, which will be expanded in subsequent publications. Our results indicate that Ka-band Doppler scatterometry could be a feasible method for wide-swath simultaneous measurements of winds and currents from space.

In the field of maneuvering target tracking, the combined observations of azimuth and Doppler may cause weak observation or non-observation in the application of traditional target tracking algorithms. Additionally, traditional target-tracking algorithms require pre-defined multiple mathematical models to accurately capture the complex motion states of targets, while model mismatch and unavoidable measurement noise lead to significant errors in target state prediction. To address those above challenges, in recent years, the target-tracking algorithms based on neural networks, such as recurrent neural networks (RNNs), long short-term memory (LSTM) networks, and Transformer architectures, have been widely used for their unique advantages to achieve accurate predictions. To better model the nonlinear relationship between the observation time series and the target state time series, as well as the contextual relationship among time series points, we present a deep learning algorithm called recursive downsample-convolve-interact neural network (RDCINN) based on convolutional neural network (CNN) that downsamples time series into sub-sequences and extracts multi-resolution features to enable the modeling of complex relationships between time series, which overcomes the shortcomings of traditional target-tracking algorithms in using observation information inefficiently due to weak observation or non-observation. The experimental results show that our algorithm outperforms other existing algorithms in the scenario of strong maneuvering target tracking with the combined observations of azimuth and Doppler.

In the context of all-digital radar systems, phase-modulated continuous wave (PMCW) based on pseudorandom binary sequences (PRBSs) appears a prominent candidate modulation scheme for applications such as autonomous driving. Among the reasons for that are its simplified transmitter architecture and lower linearity requirements, e.g., compared to orthogonal-frequency division multiplexing radars, as well as its high velocity unambiguity and multiple-input multiple-output operation capability that are characteristic of digital radars. For appropriate operation of a PMCW radar, choosing a PRBS whose periodic autocorrelation function (PACF) has low sidelobes and high robustness to Doppler shifts is paramount. In this sense, this article performs an analysis of Doppler shift tolerance of the PACFs of typically adopted PRBSs in PMCW radar systems supported by simulation and measurement results. To accurately measure the Doppler-shift-induced degradation of PACFs, peak power loss ratio (PPLR), peak sidelobe level ratio (PSLR), and integrated-sidelobe level ratio (ISLR) were used as metrics. Furthermore, to account for effects on targets whose ranges are not multiples of the range resolution, oversampled PACFs are analyzed.

(1) Background: LUS has emerged as a simple, rapid and non-invasive method for the dynamic assessment of pulmonary congestion, a major prognostic factor and a therapeutic target in AHF. (2) Methods: In the single-center prospective observational study, 42 patients hospitalized for AHF in the post-emergency polyvalent medicine department of CHU Grenoble were successively included between May 2021 and July 2022. Clinical examination, LUS and electrolyte panel results were collected daily. Vital status was assessed 30 days after the last LUS. The primary endpoint was the evolution of the number of B-lines according to the dose of diuretic administered ; (3) Results: We performed 188 LUS. Our patients were elderly (85.8 [SD 8.1]) and comorbid. The median number of B-lines decreased from 17 at admission to 7 in the middle of the hospital stay, then stagnated until discharge. Simultaneously, the median dose of diuretics, initially stable at a maximum of 40 mg/d IV, decreased to 20mg/d IV by the end of hospital stay. Patients with CKD had a higher mean number of B-lines at entry (24.2 [SD 11.6]) compared to those without CKD (8.2 [SD 8.8]). However, the evolution of B-lines number was independent of creatinine levels. 30-day all-causes mortality was significantly related to the number of B-lines at discharge (15.2 [SD 10.1] in deceased patients versus 3.9 [SD 5.4] in living patients, p

In this study, a novel and efficient method was developed for the extraction of total flavonoids from Flos Sophorae Immaturus (FSI) using ultrasound-assisted deep eutectic solvent (UAE-DES). Different DES formulations were first investigated and choline chloride/1,2-propanediol (ChCl/PD) was identified as the optimal solvent due to its highest flavonoid yield. The extraction process was optimized through single factor experiments and response surface methodology (RSM). An extraction temperature of 68 °C, a sonication time of 41 minutes, a water content of 21% and a liquid-solid ratio of 21 mL/g were identified as the optimal conditions. Under these conditions, a maximum flavonoid yield of 378.77 mg RE/g DW was achieved. The crude extract was further purified using a macroporous D-101 resin, resulting in a flavonoid extract with a purity of 83.11 ± 3.54%. The antioxidant activity of the purified extract (FSPE) was evaluated using DPPH and ABTS radical scavenging assays, showing significant antioxidant properties with IC50 values of 52.50 μg/mL and 49.47 μg/mL, respectively. The UAE-DES method developed in this study not only significantly improves the extraction yield of flavonoids from FSI, but is also in line with sustainable and environmentally friendly practices. This method offers an environmentally friendly, efficient and scalable approach for the extraction of bioactive compounds from medicinal plants and has potential applications in the food, pharmaceutical and dietary supplement industries.

Herbal Coffee is getting more popular due to its unique flavor and higher concentration of bioactive compounds, mainly polyphenols. Rosemary is a unique herb with potent antioxidant properties. A green technique called ultrasound aids in releasing bioactive substances from the plant cell wall. In this context, ultrasound-assisted herbal coffee prepared and their anti-diabetic, anti-Alzheimer, and antioxidant activities were measured while the LC/MS was used to determine the bioactive components from the herbal coffee infusion. A total of 95 secondary metabolites were putatively reported, including alkaloids, phenolic acids, and flavonoids, which we identified in the herbal coffee infusion. The total phenolic content (61.5 ± 5.1 mg GAE/g), total flavonoid content (19.3 ± 0.9 mg QE/g), and total condensed tannin (7.6 ± 0.7 mg CE/g) of herbal coffee infusion were observed to be highest of the two remaining samples. The herbal coffee extracts were used to determine all samples' antioxidant, anti-diabetic, and anti-Alzheimer activities. Using LC-MS/MS, we semi-quantified 19 phenolic metabolites. The results show numerous bioactive components in herbal coffee infusion with more potent antioxidant, antidiabetic, and anti-Alzheimer potential. Moreover, more studies must be conducted to confirm how the metabolomic profile of herbal coffee affects its flavor profile.

Introduction Color vision deficiency (CVD) constitutes one of the frequently observed eye disorders in all human populations. Color is a prominent sign utilized in the medical profession to study and identify histopathological specimens, lab instruments, and patient examination. Color deficiency affects the medical skills of students resulting in poor clinical examination and color appreciation. There is no effective screening of CVD at any level of the medical profession. Hence, this study was aimed to determine the prevalence of CVD among medical students. Materials and methods This was a cross-sectional study conducted from September 2019 to February 2020 over a period of six months in Karachi, Pakistan. All medical students aged 18-21 years of either gender enrolled in the first and second years of medical college were included in this study. The examination was performed during daylight. Ishihara plates were placed at a distance of 75 cm from the subject and tilted so that the plane of the paper lies perpendicular to the line of vision. Students were given five seconds to read the plate and one examiner was instructed to mark the checklist. A score of less than 12 out of 14 red/green test plates (not including the demonstration plate) was considered as a CVD. All statistical analysis was performed using Statistical Package for Social Sciences version 20.0 (Armonk, NY: IBM Corp). Results The mean age of the medical students was 19.61± 1.22 years. There were (n=123) 53.0% females and (n=111) 47.0% males. Most of the medical students (n=131, 56.0%) belonged to the upper-middle-class socioeconomic group. CVD was observed in (n=13) 6.0%of medical students. Age (p=0.001) and socioeconomic status (p=0.001) were the only demographic factors significantly associated with color deficiency. Conclusions Color deficiency, although an unnoticed concern, is fairly common among medical students. Medical students must be screened for CVD as this will enable them to be aware of their limitations in their future observational skills as a doctor and devise ways of overcoming them in clinical practice.

Identifying the total number of fruits on trees has long been of interest in agricultural crop estimation work. Yield prediction of fruits in practical environment is one of the hard and significant tasks to obtain better results in crop management system to achieve more productivity with regard to moderate cost. Utilized color vision in machine vision system to identify citrus fruits, and estimated yield information of the citrus grove in-real time. Fruit recognition algorithms based on color features to estimate the number of fruit. In the current research work, some low complexity and efficient image analysis approach was proposed to count yield fruits image in the natural scene. Semi automatic segmentation and yield calculation of fruit based on shape analysis is presented. Color and shape analysis was utilized to segment the images of different fruits like apple, pomegranate obtained under different lighting conditions. First the input sectional tree image was converted from RGB colour space into the colour space transform (i.e., YUV, YIQ, or YCbCr). The resultant image was then applied to the algorithm for fruit segmentation. After it is applied Morphological Operations which is enhanced image then execute Blob counting method which identify the object and count the number of it. Accuracy of this algorithm used in this thesis is 82.21% for images that have been scanned.

Embryological development of pancreas is a complex phenomenon and therefore, it can have multiple developmental aberrations. Fortunately, majority of these pancreatic ductal anomalies are asymptomatic with no clinical relevance and are incidentally detected during diagnostic cross sectional imaging or endoscopic retrograde cholangiopancreatography (ERCP) or autopsy. Occasionally, pancreatic duct anomalies can result in symptoms like abdominal pain or recurrent pancreatitis. Also, accurate pre-operative diagnosis of ductal anomalies can prevent inadvertent duct injury during surgery. Conventionally, ERCP had been used for accurate diagnosis of pancreatic duct anomalies. However, because of being invasive and associated with risk of pancreatitis, it has been replaced with magnetic resonance cholangiopancreatography (MRCP). MRCP has demonstrated high sensitivity and specificity for diagnosis of ductal anomalies which can be further improved with use of secretin enhanced MRCP. Endoscopic ultrasound (EUS) is a new diagnostic and interventional tool in the armamentarium of endoscopists and has demonstrated promising results in detection of pancreatic duct variations and anomalies. In this article, we will focus on the role of EUS in diagnosis of various pancreatic duct anomalies.

Continuous casting is the most common method for producing steel into semi-finished shapes like billets or slabs. Throughout this process, steel experiences mechanical and thermal stresses, which influence its mechanical properties. During continuous casting, decreased formability in steel components leads to crack formation and failure. One reason for this phenomenon is the appearance of the soft ferrite phase during cooling. However, it is unclear under which conditions this ferrite is detrimental to the formability. In the present research, we investigated what microstructural changes decrease the formability of microalloyed steels during continuous casting. We studied the hot compression behaviour of microalloyed steel over temperatures ranging from 650 °C to 1100 °C and strain rates of 0.1 s-1 to 0.001 s-1 using a Gleeble 3800® device. We examined microstructural changes at various deformation conditions using microscopy. Furthermore, we implemented a physically-based model to describe the deformation of austenite and ferrite. The model describes the work hardening and dynamic restoration mechanisms, i.e., discontinuous dynamic recrystallisation (dDRX) in austenite and dynamic recovery (DRV) in ferrite and austenite. The model considers the stress, strain, and strain rate distribution between phases by describing the dynamic phase transformation during the deformation in iso-work conditions. Increasing the strain rate below the transformation temperature improves hot ductility by reducing DRV and strain concentration in ferrite. Due to limited grain boundary sliding, the hot ductility improves at lower temperatures (&lt;750 °C). In the single-phase domain, DRX improves the hot ductility provided that fracture occurs at strains in which DRX advances. However, at very low strain rates, the ductility decreases due to prolonged time for grain boundary sliding and crack propagation.

Color change is the most obvious characteristic of tomato ripening stage and an important indicator of tomato ripening condition, which directly affects the commodity value of tomato. To visualize the color change of tomato fruit in mature stage, a gated recurrent unit network with an encoder-decoder structure that dynamically simulates tomato growth and development with time-dependent lines using tomato color and shape as real-time data was proposed in this paper. Firstly, the .json file was converted into a mask.png file, the tomato mask was extracted, and the tomato was separated from the complex background environment, and the tomato growth and development data set was successfully constructed. Then, a network of gated recurrent units with encoder-decoder structure was constructed to predict the future growth trend of tomato under different greenhouse temperatures. The experimental results showed that for the gated recurrent unit network of encoder-decoder structure proposed, when the hidden layer number was 1 and hidden layer number was 512, a high consistency and similarity between the model predicted image sequence and the actual growth and development image sequence would be realized, and the structural similarity index measure was 0.746. It was proved that when the average temperature was 24.93℃, the average soil temperature was 24.06℃, and the average light intensity was 11.26 Klux, the environment was the most suitable for tomato growth. The environmental data-driven tomato growth model was constructed to explore the growth status of tomato under different environmental conditions, thus to understand the growth status of tomato in time. The statement provided a theoretical foundation for determining the optimal greenhouse environmental conditions to achieve tomato maturity. And it offered recommendations for investigating the growth cycle of tomatoes, as well as technical assistance for standardized cultivation in solar greenhouses.

The possibility to test a radio frequency transceiver through the use of appropriate channel emulators allows to evaluate their performance under various operating conditions. Many systems are able to operate with a relatively limited instantaneous bandwidth by applying known statistical models. Sometimes it is necessary to evaluate the performance of a RF transceiver installed on high or very high speed platforms over predictable trajectories using optionally DEMs (Digital Elevation Models)data of the terrain to estimate the number of stimulated paths and their contributions during the flight. When the instantaneous bandwidth of the signal becomes high (over several hundred of MHz), one of the most important phenomenon to consider is the Doppler spread induced by the channel and traditional narrowband models become unuseful. In this paper there are presented some results when a time expansion is adopted in order to emulate the transceiver dynamic and the consequent Doppler spread with the aim to control the spectral purity of the emulated propagation channel.

Background: DICER1, cancer predisposition syndrome (CPS), seems to escape timely diagnosis in pediatric patients. Case report 1: A 16-year-old female patient was referred to the endocrinology ward due to a large goiter. Her medical history indicated normal sexual maturation, with menarche occurring at 13.5 years. Over the past 2.5 years, she developed pronounced androgenic symptoms, including a deepened male voice, facial, back and neckline acne, hirsutism, and menstrual irregularities leading to secondary amenorrhoea. A thyroid ultrasound identified a multinodular goiter with cystic-solid lesions containing calcifi-cations. An abdominal ultrasound identified a 5.7x6.9 cm solid mass in the right adnexal region, displacing the uterus to the left. Histopathological examination confirmed a Sertoli-Leydig cell tumor. The patient was subjected to total thyroidectomy. Histopathology revealed benign follicular cell-derived neoplasms. Thyroid follicular nodular disease was diagnosed bilaterally. DNA analysis using NGS, confirmed by the Sanger method, revealed a pathogenic heterozygotic variant c.2953>T [p.Gln985*] in exon 18 of DICER1 gene. Case report 2: A 12-year-old male patient was admitted to the pediatric surgery unit due to a 33 ml goiter. A month prior to admission, the patient discovered a palpable nodule in his neck, accompanied by hoarseness. An ultrasound revealed a multinodular goiter. Molecular analysis revealed a pathogenic heterozygotic variant c.2782C>T [p.Gln928Ter] in exon 17 of DICER1 gene. Subsequently, a total thyroidectomy was performed, and histopathological examination revealed thyroid follicular nodu-lar disease bilaterally. Conclusion: Multinodular goiter, although rare in pediatric population, when accompanied by characteristic ultrasound and histopathological features, and by additional features such as androgen excess, warrants exclusion of DICER1 syndrome.

Abstract Background: Occipital neuralgia is a debilitating condition and traditional treatments often provide limited or temporary relief. Recently, ultrasound-guided hydrodissection of the greater occipital nerve (GON) has emerged as a promising minimally invasive approach. Objectives: To describe two novel ultrasound-guided hydrodissection with 5% dextrose for GON and discuss their advantages, disadvantages, and considerations. Methods: Two case reports are presented. Case 1 describes a lateral decubitus approach for hydrodissecting the GON between the semispinalis capitis (SSC) and obliquus capitis inferior (OCI) muscles. Case 2 details a cranial-to-caudal approach for hydrodissecting the GON within the SSC and upper trapezius (UT) muscles when the GON pass through these two muscles. Results: Both patients experienced significant and sustained pain relief with improvements in function and quality of life. Conclusions: Ultrasound-guided GON hydrodissection using 5% dextrose is a promising treatment for occipital neuralgia. The lateral decubitus and cranial to caudal approaches provide additional options to address patient-specific anatomical considerations and preferences.

An exhaustive list of thirteen instances of reports confirming experimentally the relativistic Doppler relation, are examined. For those involving longitudinal Doppler, the non-relativistic relation is seen to be confirmed, within the reported experimental accuracies, to the same degree as the standard relativistic relation. Higher values of the speed of the emitter would be required to examine further the claimed confirmations. For those reports involving saturation spectroscopy, there is much confusion over the appropriate Doppler relation to be used, together with some serious analytical flaws. For the two cases that involve transverse Doppler, there are seen to be either serious faults in the theoretical part, or intrusion from the first order effect. Therefore, the reported conclusions - that the results for the experiments confirm the relativistic SR relation - cannot be justified by any of the experimental works.

Background: Bioelectrical impedance (BIA) and ultrasound (US) have become popular for estimating body fat percentage (BF%) due to their low cost and clinical convenience. However, agreement of these devices with gold standard method still require investigation. The aim was to analyze the agreement between a gold standard %BF assessment method with BIA and US devices. Methods: Twenty-three men (age 30.1 ± 7.7 years, 82.5 ± 14.9 kg, 1.77 ± 0.05 m) underwent Dual Energy X-Ray Absorptiometry (DXA), BIA (tetrapolar) and US (three-site method) %BF assessment. Pearson and concordance correlations were analyzed. T-test compared means between methods, and Bland Altman plots analyzed agreement and proportional bias. Alpha was set at &lt; .05. Results: Pearson coefficients between BIA and US with DXA were high (BIA = 0.94; US = 0.89; both p &lt; .001). Concordance coefficient was high for BIA (0.80) and moderate for US (0.49). BF% measured by BIA (24.5 ± 7.5) and US (19.4 ± 7.0) were on average 4.4% and 9.6% lower than DXA (29.0 + 8.5%), respectively (p &lt; .001). Lower and upper agreement limits between DXA and BIA were -1.45 and 10.31, while between DXA and US were 2.01 and 17.14, respectively. There was a tendency of both BIA (p = .09) and US (p = .057) to present proportional bias and underestimate BF%. Conclusions: Despite the correlation, the mean difference between the methods were significant, and the agreement limits are very wide. This indicate that BIA and US, as measured in this study, have limited potential to accurately measure %BF compared to DXA, especially in individuals with higher body fat.

Considerable amounts of agro-industrial by-products are discarded or burnt as fuel every year. However, they can be utilized as a valuable source of fiber, phenolics and other useful compounds such as antioxidants. The profile of beneficial compounds can be affected by genotype, locality, orchard management and productive season, adding or decreasing the bioactive potential of by-products. In this study, hazelnut (Corylus avellana L.) and walnut (Juglans regia L.) nutshells were investigated for their fiber content and antioxidant capacity as valorized by-products for the industry. Determinations (ORAC, TPC and color asses) were performed in hazelnut and walnut orchards located in Southern Chile during three consecutive seasons (2020/21; 2021/22 and 2022/23). Analyses of oxygen radical absorbance capacity (ORAC) in nutshells showed the highest ORAC from both species in the season 2020/21 (3217 µmol TE g1DW for hazelnut shells and 4663 µmol TE g DW1 for walnut shells), while variability in the consecutive seasons was lower for hazelnut than in walnut. Total phenolic content in hazelnut shells was positively correlated with L* (R: 0.883) and E (R: 0.924) during 2020/21 season, also with L* for 2022/23 (R: 0.907). While ORAC was negatively correlated with L* (R: 0.922) in 2021/22. In addition, morphological and structural features of both nutshells examined by Scavenging Electron Microscopy (VP-SEM) and Confocal Scavenging Laser Microscopy (CSLM) revealed differential tissue distribution and accumulation patterns of both cellulose and lignin. On the other hand, photo-colorimetric values were determined for both shells and corresponding seasons, and non-significative differences were found both shells and among seasons Finally, these results provide insight into the physicochemical characteristics of two shell types which should be considered together with antioxidant capacity in their valorization as a residual material.

Imaging of the ocular vasculature can provide new insights into the pathophysiology of ocular diseases. This study proposes a novel high-frequency super-resolution ultrasound localization microscopy (SRULM) technique and evaluates its ability to measure in vivo perfusion changes in the rat eye at elevated intraocular pressure (IOP). A 38.4 MHz center frequency linear array transducer on a VisualSonics Vevo F2 imaging platform was used to collect high frame rate (1 kHz) radiofrequency data of the posterior rat eye following systemic microbubble contrast injection. Following clutter and spatiotemporal non-local means filtering, individual microbubbles were localized and tracked. The microbubble tracks were accumulated over 10,000 frames to generate vascular images quantifying perfusion velocity and direction. Experiments were performed using physiologic relevant controlled flow states for algorithm validation and subsequently performed in vivo on the rat eye at 10 mm Hg IOP increments from 10 to 60 mm Hg. The posterior vasculature of the rat eye, including the ophthalmic artery, long posterior ciliary arteries and their branches, central retinal artery and retinal arterioles and venules were successfully visualized, and velocities quantified at each IOP level. Significant reductions in arterial flow were measured as IOP was elevated. High-frequency SRULM can be used to visualize and quantify perfusion velocity of the rat eye in both the retrobulbar and intraocular vasculature simultaneously. The ability to detect ocular perfusion changes throughout the depth of the eye may help elucidate the role ischemia has in the pathophysiology of ocular diseases such as glaucoma.

This work presents an analytical methodology to predict meat juiciness (discriminant semi-quantitative analysis using groups of intervals of intramuscular fat) and intramuscular fat (regression analysis) in Longissimus thoracis et lumborum (LTL) muscle of Bísaro pigs using as independent variables the animal carcass weight and parameters from color and image analysis. These are non-invasive and non-destructive techniques which allow development of rapid, easy and inexpensive methodologies to evaluate pork meat quality in a slaughterhouse. The proposed predictive supervised multivariate models were non-linear. Discriminant mixture analysis to evaluate meat juiciness by classified samples into three groups—0.6 to 1.1%; 1.25 to 1.5%; and, greater than 1.5%. The obtained model allowed 100% of correct classifications (92% in cross-validation with seven-folds with five repetitions). Polynomial support vector machine regression to determine the intramuscular fat presented R2 and RMSE values of 0.88 and 0.12, respectively in cross-validation with seven-folds with five repetitions. This quantitative model (model’s polynomial kernel optimized to degree of three with a scale factor of 0.1 and a cost value of one) presented R2 and RSE values of 0.999 and 0.04, respectively. The overall predictive results demonstrated the relevance of photographic image and color measurements of the muscle to evaluate the intramuscular fat, rarther than the usual time-consuming and expensive chemical analysis.

Background: Intracavitary contrast-enhanced ultrasound is widely accepted as a highly informative, safe and easily reproducible technique for diagnosis, treatment and follow- up of different pathologies of the biliary tree. Methods: This article reports the combined conclusions of personal experience with pictorial examples and literature review of applications for CEUS in intracavitary biliary scenarios. Different methodologies, choices of equipment, indications for the procedure and expected complications were identified and described from the authors’ own experience as well as from a review of published studies with total of 208 patients for the period between 2009 and 2015. Results: Indications were biliary obstruction by various etiologies, including postoperative strictures, evaluation of the biliary tree of liver donors (n=12) and evaluation of localization of a drainage catheter. One of the studies found a statistically significant difference in the diagnostic accuracy of PTC and PUSC. Conclusion: Intracavitary CEUS brings all the positive features of US together with the virtues of contrast- enhanced imaging, proving comparable accuracy to the listed techniques for diagnostics of biliary tree diseases.

This document introduces a new cryptosystem mixing two improvement standards generally used for text encryption, in order to give birth a new color image encryption algorithm capable of dealing with known attacks. Firstly, two substitution matrixes attached to a strong replacement function will be generated for advanced Vigenere technique application. At the end of this first round, the output vector is subdivided into size blocks according to the used chaotic map, for acting a single enhanced Hill circuit insured by a large inversible matrix. A detailed description of such a large involutive matrix constructed using Kronecker products will be given. accompanied by a dynamic translation vector to eliminate any linearity. A solid chaining is established between the encrypted block and the next clear block to avoid any differential attack. Simulations carried out on a large volume of images of different sizes and formats ensure that our approach is not exposed to any known attacks.

In this paper, we found new classes of exact models to the Einstein-Maxwell system of equations which describe the internal structure of a compact star made of strange matter considering the equation of state proposed by Rocha, Bernardo, de Avellar and Horvath in 2019. It has been assumed that this matter is composed of equal number of up, down and strange quarks and a small amount of electrons required to reaching the charge neutrality. If this hypothesis is correct, the neutron stars could be strange stars or hybrid stars with a thin crust of nuclei where the temperatures and pressures are capable of converting hadronic matter into this new stable phase of quarks. We have chosen a particular form of gravitational potential Z(x) that depends on an adjustable parameter related to degree of anisotropy of the models and the new solutions can be written in terms of elementary and polynomial functions. The obtained models satisfy all physical features expected in a realistic star and the expressions for mass, density and stellar radius are comparable with the experimental results.

Two-dimensional ultrasound (2D US) is commonly used in clinical settings for its cost-effectiveness and non-invasiveness, but it is limited by spatial orientation and operator dependency. Three-dimensional ultrasound (3D US) overcomes these limitations by adding a third dimension and enhancing integration with other imaging modalities. Advances in deep learning (DL) have further propelled the viability of freehand image-based 3D reconstruction, broadening clinical applications in intraoperative and point-of-care (POC) settings. This review evaluates state-of-the-art freehand 3D US reconstruction methods that eliminate the need for external tracking devices, focusing on experimental setups, data acquisition strategies, and reconstruction methodologies. PubMed, Scopus, and IEEE Xplore were searched for studies since 2014 following PRISMA guidelines, excluding those using additional imaging or tracking systems other than inertial measurement units (IMUs). Fourteen eligible studies were analyzed, showing a shift from traditional speckle decorrelation towards DL-based methods, particularly Convolutional Neural Networks (CNNs). Variability in datasets and evaluation methods hindered a comprehensive quantitative comparison, but notable accuracy improvements were observed with IMUs and integration of contextual and temporal information within CNNs. These advancements enhance freehand 3D US reconstruction feasibility, though variability limits definitive conclusions about the most effective methods. Future research should focus on improving precision in complex trajectories and adaptability across clinical scenarios.

Ultrasound (US) has become a widely used imaging modality in clinical practice, characterized by its rapidly evolving technology, advantages, and unique challenges such as low imaging quality and high variability. There is a critical need to develop advanced automatic US image analysis methods to enhance diagnostic accuracy and objectivity. Vision transformer, a recent innovation in machine learning, has demonstrated significant potential in various research fields, including general image analysis and computer vision, due to its capacity to process large datasets and learn complex patterns. Its suitability for automatic US image analysis tasks, such as classification, detection, and segmentation, has been recognized. This review provides an introduction to vision transformer and discusses its applications in specific US image analysis tasks, while also addressing the open challenges and potential future trends in its application in medical US image analysis. Vision transformer has shown promise in enhancing the accuracy and efficiency of ultrasound image analysis and is expected to play an increasingly important role in the diagnosis and treatment of medical conditions using ultrasound imaging as technology progresses.

Endoscopic ultrasound-guided gallbladder drainage (EUS-GBD) is an alternative to surgery for acute cholecystitis (AC) in poor operative candidates. However, the role of EUS-GBD in non-cholecystitis (NC) indications has not been well studied. We compared clinical outcomes of EUS-GBD for AC and NC indications. Consecutive patients undergoing EUS-GBD for all indications at a single center were retrospectively analyzed. Fifty-one patients underwent EUS-GBD during the study period. Thirty-nine (76%) patients had AC while 12 (24%) had NC indications. NC indications included malignant biliary obstruction (n = 8), symptomatic cholelithiasis (n = 1), gallstone pancreatitis (n = 1), choledocholithiasis (n = 1), and Mirizzi’s syndrome (n = 1). Technical success was noted in 92% (36/39) for AC and 92% (11/12) for NC (p &gt; 0.99). Clinical success rate was 94% and 100%, respectively (p &gt; 0.99). There were 4 adverse events in the AC group and 3 in the NC group (p = 0.62). Procedure duration (median 43 vs 45 minutes, p = 0.37), post-procedure length of stay (median 3 vs 3 days, p = 0.97), and total gallbladder related procedures (median 2 vs 2, p = 0.59) were similar. EUS-GBD for NC indications is similarly safe and effective as EUS-GBD in AC.

Abstract: Background. The newer wireless portable scanners seem to permit a quicker bedside ultrasound (US) assessment, shortening the transfer times of the portable US unit and without the hindering of connection cables. However, no substantial evidence is currently available regarding of the clinical effectiveness of such new generation devices. Objective. The aim of the current study was to evaluate the efficacy of a wireless US system with respect to a high-end US unit in a cohort of consecutive respiratory patients. Materials and Methods. This prospective observational study included a total of 72 respiratory patients admitted in the department of Internal Medicine. The US examination were independently performed by two experienced blinded examiners with a high-end Esaote MyLab-Twice scanner and a wireless double-head linear and convex probe OTE-L/C501CD. The findings resulting from the high-end US assessment and the wireless US examination were then compared each other. All the patients had a confirmation chest CT scan. Results. The high-end US machine identified 64 positive cases for pleuro-pulmonary alterations, in comparison to which the wireless US unit resulted in 13 false negative results. The respective overall sensitivity and specificity for the portable wireless US unit were of 79.69% and 100.00%, respectively. The resolution of the portable wireless US device was judged as good in 22 (31%) cases, affected by minor diagnostic limitations in 26 (36%) cases and affected by major diagnostic limitations in 24 (33%). The main diagnostic strength of the wireless probe was in the detection of pleural effusion (sensitivity 100%). The diagnostic sensitivity of the wireless probe in assessing abnormalities of the pleural line (67%), pulmonary subpleural consolidations (65%), pleural lesions (33%) and pericardial effusion (0%) was reduced. Conclusions. The newer wireless US probes may have clinical roles for the detection and management of pleural effusion when used by experienced examiners. However, sensitivity in detecting other pleuro-pulmonary pathologies is not comparable to high-end ultrasound machines.

Accurate and prompt determination of fire types is essential for effective firefighting and reducing damages. However, traditional methods such as smoke detection, visual analysis, and wireless signals pose unavailability in identifying fire types. This paper introduces FireSonic, an acoustic sensing system that leverages commercial speakers and microphones to actively probe the fire using acoustic signals, effectively identifying indoor fire types. By incorporating beamforming technology, FireSonic first enhances signal clarity and reliability, thus mitigating signal attenuation and distortion. To establish a reliable correlation between fire types and sound propagation, FireSonic quantifies the Heat Release Rate (HRR) of flames by analyzing the relationship between fire heated areas and sound wave propagation delays. Furthermore, the system extracts spatiotemporal features related to fire from channel measurements. Experimental results demonstrate that FireSonic attains an average fire type classification accuracy of 95.5% and a detection latency of less than 400 ms, satisfying the requirements for real-time monitoring. This system significantly enhances the formulation of targeted firefighting strategies, boosting fire response effectiveness and public safety.

The difference in the Hubble-Lemaitre constant determined by different probes is a yet unexplained observation. This paper proposes the contention that the tension could be explained by the Doppler shift effect of Ia supernovae or Cepheids, driven by the rotational velocity of their host galaxies relative to the rotational velocity of the Milky Way. While the effect of the Doppler shift is expected to be mild, observations show that it can lead to systematic differences in the apparent brightness, and consequently the estimated distances. A simple experiment is done by repeating a previous analysis. When using the original set of supernovae, $H_o$ is 73.758$\pm$1.943 km/s/Mpc. When using a subset of supernovae such that the host galaxies rotate in the same direction as the Milky Way, $H_o$ drops sharply to 69.049$\pm$3.42 km/s/Mpc, showing a far milder tension with the $H_o$ determined by the CMB. When using a subset of Ia supernovae that rotate in the opposite direction, Ho does not decrease, but instead it increases the Ho tension to 74.182$\pm$3.2. Further analysis will be required to determine the link between Ho observed by using Ia supernovae or Cepheids and the rotational velocity of the host galaxies.

It is important to understand the statistical-physical structure of the rain in the vertical so that observations aloft can be translated meaningfully into what will occur at the surface. In order to achieve this understanding, it is necessary to gather high temporal and spatial resolution observations of rain in the vertical. This can only be accomplished using radars. It can be achieved by translating radar Doppler spectra into drop size distributions which can then be integrated to calculate variables such as the rain fall rate. A long-standing difficulty in using such measurements, however, is the problem of vertical air motion which can shift the Doppler spectra, and, therefore, significantly alter the deduced drop size distributions and integrated variables. In this work, we illustrate the improvement in measured rain structures using a new approach for removing the effect of mean vertical air motion. It is demonstrated that the new approach proposed here not only produces what appear to be better estimates of the rainfall rates, but, also as a consequence, provides estimates of the temporal and spatial regionally coherent updraft and downdrafts occurring in the precipitation. Furthermore, the technique is readily applicable to other radars especially those operating at non-attenuating frequencies.

In many image processing and computer vision applications, the main aim is to describe image contents. So, different visual properties such as color, texture and shape are extracted to make aim. In this respect, texture information play important role in image description and visual pattern classification. Texture is referred to a specific local distribution of intensities that is repeated throughout the image. Since now different operations or descriptors have been proposed to analysis texture characteristics. In the multi object images specific texture operators usually doesn’t provide accurate results. So, in many cases, combination of texture operators are used to achieve more discriminant features. In this paper, some combination methods are survived to analysis effect of combinational texture features in image content description. Also, in the result part, different related methods are compared in terms of accuracy and computational complexity.

Oriented strand board (OSB) panels are widely marketed for several applications, from building to packaging. The manufacturing of poplar OSB started recently in Northern Italy representing a relevant innovation in the sector since this product is usually made of coniferous wood. The thermal treatment is widely used for reducing the hygroscopicity of wood-based products, nonetheless it influences the mechanical behavior and degrades the main components of wood, which can affect their finishing. Therefore, it is important to know the properties of the treated surfaces. To this purpose, in this study a lot of OSB panels, made of poplar wood, 15 mm thick and with a density of 590 kg/m³, were thermally treated under vacuum conditions at 190 °C for 2 h and then subjected to accelerated weathering. The changes in color and in wettability due to treatment and accelerated weathering were studied. The thermal treatment determined a significant darkening of the color; the accelerated weathering darkened the untreated surfaces and, on the opposite, lightened the thermo-treated surfaces. The wettability decreased after thermal treatment and increased after weathering, more evidently in treated panels. Overall, this study improves the knowledge about the behavior of the surface of thermo-treated poplar OSB, which is relevant for the industrial coating of this product.

Bisphenol-A (BPA) represents an important co-monomer for obtaining polycarbonate, epoxy resins, flame retardants, in paint, and other chemicals products. Products containing BPA are widely used, and thus, we can find it in the environment: in the air, in the soil, in natural surface water and in sediments, underground water in landfills, and in wastewater. BPA disturbs human and animals’ health. This influences the enzymatic, androgenic, neurological, liver and reproductive systems at different stages of human life: like in fetal stage, children and adults’ stages. Taking these inconveniences into account, it is very important to remove BPA from water. Ultrasonic technology can be considered a verry sustainable and efficient method to remove BPA from water. The advantages of this method is easy to implement on existing water treatment and purification facilities, it does not produce residual compounds that produce sludge, the time required for degradation is of the order of 1-2 hours and the level of degradation is very high. In this work, we presented the studies on the efficiency of ultrasonics under air atmosphere on the degradation of BPA. The influence of the frequency and of some additional compounds such as carbon tetrachloride, FeSO4 7H2O (FS), and ethyl anthraquinone (EAC) was studied. Three different frequencies were used: 1146 KHz, 864 KHz, 580 KHz, at a power of 50 W. It was identified the efficiency of BPA degradation over a period of 60 minutes, with sampling every 15 minutes. Using the LC-MS/MS technique, the degradation compounds were identified that result from the application of ultrasound processes. Pathways of BPA degradation were also proposed.

Background: The transversus abdominis plane (TAP) block has gained increasing importance as a very effective pain relief in for caesarean section. This study aimed to compare bupivacaine (Group B), bupivacaine with dexmedetomidine (Group BD) and bupivacaine with dexamethasone (Group BDx) applied in ultrasound-guided TAP block in the treatment of CS postoperative pain. Material and Method: American Society of Anesthesiologists I and II pregnant women who underwent cesarean section were included in the study. Forty patients were admitted in each group. All patients were applied TAP block with ultrasound guidance by administering the medications of the group in which they were included. Results: Body mass index (BMI) and operation duration were higher in Group B (p*=0.01 and 0.004, respectively). Instant tramadol requirement and amount were higher in Group B at some of follow up times. Patient satisfaction scale were better in Group BD and Group BDx. Conclusion: TAP block significantly reduces pain after cesarean section, prolongs the time to first analgesic request, and reduces the need for additional opioid analgesics. The addition of adjuvant to the TAP block usually improves the postoperative clinical condition. However, some special conditions such as body mass index (BMI) may negatively affect the clinical situation. Comprehensive, standardized, randomized controlled studies are needed to compare results under different conditions.

Surface velocity is traditionally measured with in situ techniques such as velocity probes (in shallow rivers) or Acoustic Doppler Current Profilers (in deeper water). In the last years, researchers have developed remote sensing techniques, both optical (e.g., image-based velocimetry techniques) and microwave (e.g., Doppler radar). These techniques can be deployed from Unmanned Aerial Systems (UAS), which ensure fast and low-cost surveys also in remotely-accessible locations. We compare the results obtained with a UAS-borne Doppler radar and UAS-borne Particle Image Velocimetry (PIV) in different rivers, which presented different hydraulic–morphological conditions (width, slope, surface roughness and sediment material). The Doppler radar was a commercial 24 GHz instrument, developed for static deployment, adapted for UAS integration. PIV was applied with natural seeding (e.g., foam, debris) when possible, or with artificial seeding (woodchips) in the stream where the density of natural particles was insufficient. PIV reconstructed the velocity profile with high accuracy typically in the order of a few cm s⁻¹ and a coefficient of determination (R²) typically larger than 0.7 (in half of the cases larger than 0.85), when compared with acoustic Doppler current profiler (ADCP) or velocity probe, in all investigated rivers. However, UAS-borne Doppler radar measurements show low reliability because of UAS vibrations, large instrument sampling footprint, large required sampling time and difficult-to-interpret quality indicators suggesting that additional research is needed to measure surface velocity from UAS-borne Doppler radar.

The need for miniaturized shear force sensors is expanding, particularly for biomedical applications. Examples include measuring interfacial shear stresses between a human and an external device (e.g., footwear or a prosthesis). However, there are considerable challenges in designing a shear sensor for these applications due to the need for a small package, low power requirements, and resistance to interference from motion artifact and electromagnetic fields. This paper presents the design, fabrication, and characterization sensor that measures two-axis shear force by detecting displacement between a color panel and a red, green, and blue light-sensing photodiode. The sensor response to applied displacements and forces was characterized under benchtop testing conditions. We also present the design of a prototype wireless version of the sensor for integration into footwear. The sensor exhibited strong agreement with gold standard measurements for two axis shear displacements (R2>0.99, RMSE≤5.0 µm) and forces (R2>0.99, RMSE≤0.94 N). This performance, along with the sensor’s scalability, miniaturized form, and low power requirements make it well-suited a variety of biomedical applications.

Synesthesia is a psychological phenomenon where sensory signals become mixed. Input to one sensory modality produces an experience in a second, unstimulated modality. In “grapheme-color synesthesia”, viewed letters and numbers evoke mental imagery of colors. The study of this condition has implications for increasing our understanding of brain architecture and function, language, memory and semantics, and the nature of consciousness. In this work, we propose a novel application deep learning to model perception in grapheme-color synesthesia. Achromatic letter images, taken from database of handwritten characters, are used to induce synesthesia. Results show the model learns to accurately create a colored version of the inducing stimulus, according to a statistical distribution from experiments on a sample population of grapheme-color synesthetes. The spontaneous, creative mental imagery characteristic of the synesthetic perceptual experience is reproduced by the model. A model of synesthesia that generates testable predictions on brain activity and behavior is needed to complement large scale data collection efforts in neuroscience, especially when articulating simple descriptions of cause (stimulus) and effect (behavior). The research and modeling approach reported here begins to address this need.

Background: Hashimoto’s thyroiditis (HT) is an autoimmune disease that progressively leads to thyroid gland destruction and hypothyroidism. Patients produce antibodies against two thyroid-specific antigens: thyroglobulin and thyroid peroxidase. As a result of the abnormal amount of thyroid hormone produced and its autoimmune etiology, patients with HT display a higher frequency of either autoimmune or non-autoimmune dermatological disorders. On ultrasound examination, HT can be detected by observing an enlarged thyroid gland with hypoechoic parenchymal regions or by observing a small gland indicating atrophy and diffusely heterogeneous parenchyma. Changes in the parenchymal vascularity can be observed as decreased or increased levels of vascularization. Objective: This study aimed to analyze the role of clinical data and ultrasound evaluation of patients with HT in suggesting an association with dermatological disorders. Patients and methods: Complete dermatological and endocrinological assessments as well as ultrasonography of the thyroid and lymphnodes were performed in HT patients. Results: The data obtained showed that a family history of thyroid disease, increased diameter of the inferior thyroid artery, and the presence of cervical lymphadenopathy were more frequent in the group of patients with dermatological diseases. Taken together, our results suggest the usefulness of ultrasound in determining a possible association between HT and dermatological disorders.

The effect of fungicides on fermentation is of paramount importance to control the quality and safety of wines. In this work, the quality (oenological parameters, color, phenolic content, antioxidant activity, and fungicide residues) of wines from Monastrell grapes fortified with iprovalicarb, mepanipyrim and tetraconazole fungicides was evaluated. Along of the winemaking process, initial residues of mepanipyrim and tetraconazole were removed in more than a 90 % while dissipation of iprovalicarb was around 73 %. Significant statistical differences were found in presence of iprovalicarb and mepanipyrim residues especially at the highest concentration assayed. For both fungicides, an increase of the volatile acidity (between 4 and 8.6 times), the lactic acid content (between 8.6 and 20.5 times), the percentage of polymeric anthocyanins (between 1.3 and 1.7 times) and also a slight increase of the total phenolic index and the total anthocyanins content determined by spectrophotometry was observed. On the contrary, the total monomeric anthocyanins content decreased about 16.3 and 28.6 % in presence of iprovalicarb and mepanipyrim, respectively. These results could be related with the addition of SO2 to the grape must and a higher development of acetic acid or lactic bacteria in presence of these fungicides. The color of the final wines was also different in comparison with the control, with a higher yellow component, color intensity, tonality and hue angle, because of pH changes in the medium. Tetraconazole fermentations had a more similar trend to the control wine, probably due to the lower concentration of this fungicide in the grape must at the initial time. No effects on the antioxidant activity was observed for anyone of the target fungicides. A multivariate statistical analysis was done to view interrelationships between different variables (color and anthocyanins profile). The obtained model allowed to separate wines according to the fungicide treatment applied.

In this paper, the concept of absolute airspace is further elaborated, and the time transform effect, the frequency transform relation of clock timing, and the principle of Doppler effect of special relativistic light are analyzed and demonstrated. Based on the concept of absolute airspace, a new and accurate Doppler effect relation of light (electromagnetic wave) is proposed. It is proved that there is a synchronous relationship between the time shift effect and the frequency change of the timing inside the clock. When the light (electromagnetic wave) source is in motion, the Doppler effect includes two physical mechanisms: the frequency change caused by time transformation effect and the frequency change caused by relative motion. When the light source is in motion, the Doppler effect of the light there are some differences in different directions due to the rotation of the earth. The relation of Doppler effect of special relativistic light is only a highly approximate relation, and its theoretical basis, special relativity, is flawed in principle.

Assessment of cardiac function is the leading parameter when evaluating the state of the cardiovascular system of patients undergoing chronic hemodialysis. The aim of the paper: to assess the state of the cardiovascular system of these patients using new sensitive echocardiography and Doppler techniques and thus advance the prevention of cardiovascular disease. Method: Twenty children with end-stage renal insufficiency on chronic hemodialysis and twenty healthy controls underwent echocardiographic monitoring using standard Doppler and tissue Doppler imaging. Structural and functional changes in the left ventricle were evaluated. Results: Patients on hemodialysis had significantly greater left ventricular mass indices compared to the controls (p < 0.001). The patients on hemodialysis had preserved systolic function—their fractional shortening, ejection fraction and Sm (systolic myocardial velocity) did not differ significantly compared to the controls (p > 0.05). Early diastolic function in children on hemodialysis was also preserved: the E/A and Em/Am ratio did not differ significantly from the control group (p > 0.05). Children on hemodialysis exhibited impaired late diastolic function (compliance index), that is, considerably higher E/Em compared to controls (p < 0.00). Myocardial Performance Index values showed statistically significant elevation in children on hemodialysis compared to the control group (p < 0.001). Conclusion: Tissue Doppler in tandem with conventional Pulsed Doppler can provide additional information on left ventricular filling pressures (E/Em) in children on hemodialysis. It is therefore recommended to perform routine measuring of Em waves and the E/Em ratio, not only in order to evaluate myocardial relaxation and ventricular filling pressures, but primarily to stratify risk and provide a prognosis.

This in vitro study aimed to analyze the surface roughness (Ra) and color stability (ΔEab, ΔE00) following simulated mechanical brushing, and to evaluate the microtensile (μTBS) to dentin of Self Adhering Resin Flowable (SARF). The selected materials were Constic, Yflow AS, and Tetric N flow (TNF/control). Thirty composite resin cylinders were fabricated for surface property evaluation. Ra and color were assessed both before and after simulated brushing. The thresholds of 50:50% perceptibility and acceptability of color difference of the evaluated resins were assessed. For μTBS analysis, fifteen molars were selected, sectioned to expose flat dentin surfaces, and restored according to manufacturers' instructions. Subsequently, they were sectioned into sticks for microtensile testing. Statistically significant differences in Ra among the groups, with Constic exhibiting the highest Ra value (p < 0.05), while Yflow AS showed the lowest Ra value. No statistically significant difference in color was observed among the groups (p > 0.05). The 50:50% perceptibility and acceptability thresholds set at 1.2 and 2.7 for ΔEab and 0.8 and 1.8 for ΔE 00. All the results fell within the acceptable limits. The mean μTBS values of Constic, Yflow AS, and TNF were 10.649 MPa, 8.170 MPa, and 33.669 MPa, respectively. The study revealed increased Ra and comparable color stability among all tested composite resins after abrasion. However, SARF exhibited lower μTBS compared to conventional using an adhesive system.

This study investigates the effects of ambient illumination and negatively polarized text color on visual fatigue, exploring the issue of visual fatigue when using visual display terminals in low-illumination environments. The research methodology utilized an experimental design to collect data on changes in pupil accommodation and blink rate through an eye tracker. Partici-pants completed a reading task while exposed to various text colors and ambient light conditions to evaluate visual fatigue and cognitive performance. The study's findings suggest that text color significantly affects visual fatigue, with red text causing the highest level of visual fatigue and yellow text causing the lowest level of visual fatigue. Improvements in ambient lighting reduce visual fatigue, but the degree of improvement varies depending on the text color. Additionally, cognitive performance is better when using yellow and white text but worse when using red text. Yellow text is the most effective choice for reducing visual fatigue under negative polarity. In-creasing ambient lighting can also improve visual fatigue in low-illumination conditions. These findings will offer valuable guidance for designing visual terminal device interfaces, especially for low-illumination or night environments, to minimize visual fatigue and improve the user ex-perience.

This research assesses the classification of Arabic coffee into three primary variations (light, medium, and dark) using simulated data based on actual measurements of color information, antioxidant laboratory tests, and chemical composition tests. Two types of simulated data were generated, with the standard deviation of the measures varied. Multiple classifiers were used for classification. The findings demonstrate the use of color information in accurately distinguishing Arabic coffee types. The different CIE color values, as well as the excellent connection between color information and coffee classes, lead to flawless classification results. However, depending primarily on antioxidant information results in lower classification performance, with variability amongst classifiers due to increasing data complexity. Chemical composition information, on the other hand, possesses outstanding discriminatory strength, allowing faultless classification on its own. Certain characteristics, such as crude protein and crude fiber, show strong correlations and are critical in the classification of coffee types. Based on the findings, it is recommended to create a mobile application that uses image recognition to analyze coffee color while providing chemical composition information. End users, such as consumers, will be able to make informed judgments regarding their coffee preferences owing to this application.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

Color can direct visual attention to specific locations through bottom-up and top-down mechanisms. Using Continuous Flash Suppression (CFS) as way to investigate the factors that gate access to consciousness, the current study investigated whether color also directly affected the timing of conscious perception. Low or high spatial frequency (SF) gratings with different orientations were shown as targets to the non-dominant eye of human participants. CFS patterns were presented at a rate of 10Hz to the dominant eye to delay conscious perception of the targets, and participants had the task to report the target’s orientation as soon as they could see it. With low-SF targets, two types of color-based effects became evident. First, when the targets and the CFS patterns had different colors, the targets entered consciousness faster than in trials where the targets and CFS patterns had the same color. Second, when participants searched for a specific target color, targets that matched these search settings entered consciousness faster compared to conditions where the target color was irrelevant and could vary from trial to trial. Thus, the current study demonstrates that color is a central feature of human perception and leads to faster conscious perception of visual stimuli through bottom-up and top-down attentional mechanisms.