Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% [email protected], which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

With the advancement of technology, signal modulation types are becoming increasingly diverse and complex. The phenomenon of signal time-frequency overlap during transmission poses significant challenges for the classification and recognition of mixed signals, including poor recognition capabilities and low generality. This paper presents a recognition model for fine-grained analysis of mixed signal characteristics, proposing a Geometry Coordinate attention mechanism and introducing a low-rank bilinear pooling module to more effectively extract signal features for classification. The model employs a residual neural network as its backbone architecture and utilizes the Geometry Coordinate attention mechanism for time-frequency weighted analysis based on information geometry theory. This analysis targets multiple-scale features within the architecture, producing time-frequency weighted features of the signal. These weighted features are further analyzed through a low-rank bilinear pooling module, combined with the backbone features, to achieve fine-grained feature fusion. This results in a fused feature vector for mixed signal classification. Experiments were conducted on a simulated dataset comprising 39,600 mixed signal time-frequency plots. The model was benchmarked against a baseline using a residual neural network. The experimental outcomes demonstrated an improvement of 9% in the exact match ratio and 5% in the Hamming score. These results indicate that the proposed model significantly enhances the recognition capability and generalizability of mixed signal classification.

Lean body mass (LBM) is correlated with powerlifting performance in athletes competing in different bodyweight classes. However, it remains unknown whether changes in LBM are correlated with performance changes in powerlifters preparing for a competition. Aim of the study was to investigate the changes in LBM and performance in powerlifters preparing for a competition. Eight male powerlifters (age 31.7±9.8years, height 1.77±0.06m, weight 99.2±14.6kg) and three female powerlifters (age 32.7±16.3years, height 1.54±0.06m, weight 66.6±20.9kg), participated in the study. Athletes followed individualized periodized training programs for 12 weeks aiming to maximize their performance for the national championship. Maximum strength (1-RM) in squat, bench press, and deadlift, body composition, grip strength, anaerobic power, quadriceps’ cross sectional area and vastus lateralis muscle architecture were measured before and after the training period. Significant increases were found after the training period in squat (5.8±7.0%, P

Semi-Interlocking Masonry (SIM) represents an innovative building system developed at the Centre for Infrastructure Performance and Reliability at The University of Newcastle, Australia. This system employs a unique approach to interlocking mortar-less engineered masonry panels constructed from SIM units. These units are designed to offer substantial energy dissipation capacity, primarily attributed to the friction occurring on the sliding bed joints between the units within the panel during seismic events. The primary aim of this study is to evaluate the viability of incorporating semi-interlocking masonry as infill panels in the construction of multi-storey buildings across diverse geographical locations with varying seismic conditions in Australia. To assess the feasibility of SIM panels in different conditions (according to Australian Standard AS1170) in Australia, a comprehensive analysis using Strand7 is conducted on a three-storey structure incorporating traditional masonry infill panels and SIM panels. The comparison of displacement and base shear capacities is carried out in response to seismic events across various scenarios in different locations within Australia. The insights gained from this comparative analysis contribute valuable information regarding the viability of implementing SIM as a contemporary construction material.

This research focuses on examining the responses of interest groups listed in the European Transparency Register to the ongoing Russia-Ukraine war. Its aim is to investigate the nuanced reactions of 2,579 commercial and business associations and 2,957 companies and groups to the conflict, as expressed through their X (Twitter) activities. Utilizing advanced text mining, NLP and LDA techniques, this study conducts a comprehensive analysis encompassing language dynamics, thematic shifts, sentiment variations, and activity levels exhibited by these entities both before and after the outbreak of the war. The results obtained reflect a progressive decreasing in negative emotions regarding the conflict over time. Likewise, multiple forms of outside lobbying are identified in the communication strategies of interest groups. All in all, this empirical inquiry into how interest groups adapt their messaging in response to complex geopolitical events holds the potential to provide invaluable insights into the multifaceted role of lobbying in shaping public policies.

Chinese texts often feature a substantial volume of normative content, and their analysis has increasingly become a focal point in recent semantic analysis endeavors. Enhancing the effectiveness of text classification and clustering is pivotal in unveiling the intricate semantics within extensive textual data. Empirical research within the realm of computational social science has underscored the need for improved explanatory power when it comes to general text clustering methods applied to normative texts. This study introduces an innovative hierarchical clustering method that incorporates part-of-speech (POS) features and pioneers a novel semantic network model. It achieves this by amalgamating a POS-based feature weight calculation method with hierarchical clustering techniques. To assess its efficacy, the method is rigorously evaluated across three diverse text datasets, encompassing normative reports, news articles, and social media content. The experimental results unequivocally demonstrate the superior performance of the POS-HC method, surpassing the traditional TF and TF-IDF feature extraction methods in terms of clustering accuracy, and surpassing some existing clustering methods. Furthermore, its classification effectiveness exhibits notable advantages, particularly in the semantic classification of normative texts.

The next-generation communication systems demand integration of sensing, communication, and power transfer (PT) capabilities, requiring high spectral efficiency, energy efficiency, and low cost, while also necessitating robustness in high-speed scenarios. Integrated sensing and communication systems (ISACS) exhibit the ability to simultaneously perform communication and sensing tasks using a single RF signal, while simultaneous wireless information and power transfer (SWIPT) systems can handle simultaneous information and energy transmission, and orthogonal time frequency space (OTFS) signals are adept at handling high Doppler scenarios. Combining the advantages of these three technologies, a novel cyclic prefix (CP) OTFS based integrated simultaneous wireless sensing, communication, and power transfer system (ISWSCPTS) framework is proposed in this work. Within the ISWSCPTS, the CP-OTFS matched filter (MF) based target detection and parameters estimation (MF-TDaPE) algorithm is proposed to endow the system with sensing capabilities. To enhance the system’s sensing capability, a waveform design algorithm based on CP-OTFS ambiguity function shaping (AFS) is proposed, which is solved by iteratively method. Furthermore, to maximize the system’s sensing performance under communication and PT Quality of Service (QoS) constraints, a semidefinite relaxation (SDR) beamforming design (SDR-BD) algorithm is proposed, solved using through SDR technique. Simulation results demonstrate that the ISWSCPTS exhibits stronger parameter estimation performance in high-speed scenarios compared to orthogonal frequency division multiplexing (OFDM), waveform designed by CP-OTFS AFS demonstrates superior interference resilience, and beamforming designed by SDR-BD strikes a balance in the overall performance of the ISWSCPTS.

Corporate Sustainability has garnered increasing attention within the business community, as corporates communicate to influence its stakeholders for building sustainable relationships. There has been a surge in research exploring its connection to firm performance but, existing studies lack a cohesive and concentrated approach. This study employs scientometric and bibliometric methods to analyse scientific production which signals a scarcity of research from developing countries, indicating a need for greater investigation. Focussing on specific subfields of Corporate Sustainability and Firm Performance, we analyze and narrow down the scope of our study to a focussed sample. Employing use of structured methods and PRISMA Protocol, this scientifically rigorous study, points towards identification of research themes linking sustainability practices to firm performance for achieving business excellence. It goes beyond mapping of literature, thereby establishing linkages to Sustainable Development Goals (SDGs). Our analysis reveals clusters centered on Environmental Performance, Firm Performance, Corporate Sustainability Reporting, Corporate Social Performance and Green Supply Chain Management with significant citations related to various SDGs. We make use of time series analysis to determine the future trends of research in the field. This scientometric and bibliometric analysis study contributes to a more focused understanding of the linkages between corporate sustainability and firm performance, emphasizing the need for cohesive research approaches to address the complexities of sustainable business practices and their implications for financial performance and the economy.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

The once near-extinct Russell’s viper has recently come back to the area beyond its historical range. A couple of decades ago, its distribution was confined to 11 districts of Bangladesh. Hence, the study aims to update the distributional map of Russell’s Viper (Daboia russelii) across the country and find out the surges' causal factors. Both primary and secondary data were utilized in this study. It revealed that the distributional range of this snake was expanded from 22 to 33 districts in 2024. The respondents noted that climatic stressors like high humidity accompanied by hot weather, increased salinity, and increased frequency of flooding facilitated the spreading of the viper across the country. The cropping pattern and crop diversification were another major contributing factor. The shifting of the single-cropped area to a multi-cropped area in the Barind tract increased its main prey rats. Contrarily, the killing of natural predators such as foxes, monitor lizards and mongoose led to the rise in the snake population. The destruction of vegetation coverage in the upper part of the Padma Basin facilitated the movement of Russell's vipers downstream.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

The purpose of this paper is to explore the implementation of Retrieval-Augmented Gen- 14 eration (RAG) technology with open-source Large Language Models (LLMs). For this purpose, a 15 web-based application named PaSSER that integrates RAG with three models - Mistral:7b, 16 Llama2:7b: Orca2:7b, is developed. In its development various technologies are used, including 17 Blockchain for managing and storing assessment results of built-in testing modules. PaSSER em- 18 ploys a set of evaluation metrics for LLMs’ performance - METEOR, ROUGE, BLEU, Perplexity, 19 Cosine similarity, Pearson correlation, and F1 score. The specialized knowledge base is in the smart 20 agriculture domain. As an illustration, the paper presents results and analysis of two tests. First one 21 is assessing the performance of LLMs across different hardware configurations, the other is deter- 22 mining the model that delivers most accurate and contextually relevant responses within the RAG. 23 The paper also discusses the integration of blockchain technology with LLMs to manage and store 24 assessment results within a blockchain environment. The tests revealed that Mistral:7b demon- 25 strates the best results across most of the evaluated metrics. The discussion section comments on 26 technical and hardware considerations that affect the performance of LLMs. Future development 27 will focus in leveraging new larger pre-trained open-source LLMs, exploring different finetuning 28 approaches, and further integration with Blockchain and IPFS.

This paper presents a new semi-explicit algorithm for parameters estimation in a time-fractional generalization of dual-phase-lag heat conduction model with the Caputo fractional derivatives. It is shown that this model can be derived from a general linear constitutive relation for the heat transfer by conduction when the heat conduction relaxation kernel contains the Mittag-Leffler function. The model can be used to describe heat conduction phenomena in a material with power-law memory. The proposed algorithm of parameters estimation is based on the time integral characteristics method. The explicit representations of the thermal diffusivity and the fractional analogues of the thermal relaxation time and the thermal retardation are obtained via a Laplace transform of the temperature field and utilized in the algorithm. An implicit relation is derived for the order of fractional differentiation. In the algorithm, this relation is resolved numerically. An example illustrates the proposed technique.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

In the dynamic landscape of the telecommunications industry, understanding and mitigating customer churn is paramount for maintaining competitive advantage and sustaining revenue streams. This comprehensive literature review delves into the intricacies of customer churn prediction, a crucial aspect in fortifying the bond between telecom businesses and their customers. The review methodically analyzes 11 articles published between 2000 and March 2024, spotlighting the strategic role of Customer Relationship Management and the prevalence of high churn rates that necessitate a shift from customer acquisition to retention strategies. Furthermore, the review navigates through the challenges inherent in churn prediction, including the complexities of managing large, imbalanced, and noisy datasets and the intricacies involved in model selection and optimization. Despite these challenges, the paper highlights the superior capability of machine learning techniques in handling complex datasets to provide accurate predictions, albeit acknowledging their practical complexities. The main aim of the study is to provide an overview, serving as a knowledge base for researchers interested in machine learning techniques within the realm of telecommunications.

Infection with the malaria parasite Plasmodium, remains a major cause of illness and death world-wide. The development of evasion strategies by the parasite from host immunity and its adaptability to antimalarial drugs has raised the urgency for developing new strategies to combat this disease. One promising avenue is targeting telomeres – sequences found at chromosome termini– and telomerase – the enzyme that catalysis synthesis of telomeres using an intrinsic RNA template. As telomeres shorten critically, cells undergo replicative senescence or apoptosis. Plasmodium, lacking telomerase activity in its human stages, exploits alternative mechanisms, accelerating telomere shortening, aging, and immune evasion. Chemical telomerase inhibitors show promise as antimalarials. In this review, we examine the potential of targeting this system in malaria therapy, with telomerase inhibitors offering a novel approach. A systematic search on PubMed using Boolean techniques identified 246 relevant articles from 1985 to March 31, 2024. After filtering, 43 articles met inclusion criteria, supplemented by snowball sampling. The telomerase inhibitor drug strategy is widely applicable against cancer. However, given the drugability of telomerase and the absolute requirement for active telomere maintenance in the vast majority of parasites including plasmodium, telomerase and telomere maintenance could well represent the Achilles heel of the parasite

Among earth’s microbial populations are the genes, functional capacities, generational memory and sentient cognition that enable microorganisms to adapt and thrive in the full range of ecological conditions found on planet earth. In prior sequential publications, we considered fundamental properties (e.g., use of and responses to sound, light, vibrations) and features of microorganisms that cause them to be critical co-partners of human and other holobionts as well as the potential benefits for humanity that can be gained by fully applying quantum-related and novel capacities of microbial life. In this narrative review we: 1) discuss key concepts concerning a microbially-enhanced and sustainable future, and 2) focus on electric- and magnetic- based features of microorganisms that make them pivotal for myriad benefits ranging from beyond pharma-based health and wellness to free- and/or renewable energy and restorative agriculture to improved human networking. While the benefits are many, the risks posed by hazardous electric or magnetic field exposures to both holobionts and microbial communities are significant. This review concludes that microbes and their remarkable capacities offer both humanity and the planet a much brighter future if we reverse the demonization of microbes and wanton microbiome degradation that has predominated much of the past century.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

The giant octopus caught off the east coast of Korea is an important fishery resource with the largest haul and is mostly caught using net pots. While giant octopus pots have different shapes, drum, rectangular, and cylinder pots are mostly used. However, these pots have not been thoroughly evaluated. Here, we evaluated the fishing performance of three giant octopus pots, their fluid resistance, and underwater movement. Six sea trials were conducted near the Hupo region in Gyeongsangbuk-do. In total, 163 individuals (62,724 g), 190 individuals (49,913 g), and 154 individuals (52,364 g) were caught using drum, rectangular, and cylinder pots, respectively. Drum pots showed significant differences in the amount of catch by weight (ANOVA test, p<0.05). Moreover, the percentage of minimum conservation size was the lowest in cylinder pots (6.5%). Drum pots showed the highest stability in the underwater stability test, while underwater fluid resistance at 2.5 kt fluid speed was in the following order: drum pots (7.66 kgf) > rectangular pots (7.16 kgf) > cylinder pots (7.04 kgf). Therefore, drum pots showed excellent fishing performance. This study provides foundational data for developing managing systems for giant octopus resources and establishing the extent of fishing gear usage.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

This study evaluates the viability of n-octanol as an alternative fuel in a direct-injection diesel engine, aiming to enhance sustainability and efficiency. Experiments employed varying blends of n-octanol (10%, 30%, and 50% by volume) with pure diesel, analyzing impacts on engine performance and emissions. The methodology involved testing each blend in a single-cylinder engine, measuring engine performance parameters such as brake torque and brake power under full load conditions across an engine speed range from 1400 to 2500 rpm. Comparative assessments of performance and emission characteristics at a constant engine speed of 1700 rpm were also conducted with varying loads. Results indicated that while n-octanol blends consistently improved brake thermal efficiency, they also increased brake specific fuel consumption due to the lower energy content of n-octanol. Consequently, while all n-octanol blends reduced nitrogen oxides (NOx) emissions compared to pure diesel, they also significantly decreased carbon monoxide, hydrocarbons, and smoke opacity, presenting a comprehensive reduction in harmful emissions. However, the benefits came with nuanced trade-offs: notably, higher concentrations of n-octanol (especially the 50% blend) led to a relative increase in NOx emissions as the octanol ratio increased. The study concludes that n-octanol significantly improves engine efficiency and reduces diesel dependence, but optimizing the blend ratio is crucial to balance performance improvements with comprehensive emission reductions.

Radio communication system in an underground mine is one of the very essential systems for the underground mine. It is required that the radio communication system must be reliable from the starting to construct the underground mine to the closure of the mine. However, underground mine radio communication systems reliability is required to be tested on an active radio communication system in a real environment. In the study was suggested a new research methodology that is studied reliability using dynamic system modeling on Vensim software instead of traditional method to study the reliability of radio communication systems calculating large-scale differential equations. In other words, we suggest a new research methodology. The Motorola Dimetra (TETRA) radio communication system's availability readiness information was used to simulate the reliability of the underground mine radio communication system probability of reliability using Vensim software for system dynamic modeling.Also, the factors that affect the reliability of underground mining radio communication systems was studied. The study was determined factors that affect the underground mine radio communication system from the following risks. The study was in the examples of the Oyu Tolgoi underground mine. The factors that affect the reliable operation of the underground mine radio communication system were determined using the failure statistics of TETRA radio communication system in the Oyu Tolgoi mine in 2015-2018.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Cartoons in the era of digital media are among the most prevalent medium of entertainment for the children, parents also encourage them to view such contents to engage the children which make an area need to be explained exhaustively by adopting new approaches. There are lot of studies in the past conducted to explain the impacts of the cartoons on the children however, it is remarkable fact that there is lack of the studies in the literature which directly address the observation about the above mentioned impacts in view of the teacher’s. This study deals with the educational, emotional, behavioral and Religious etc. impacts of cartoons on kids in view of teachers of the primary schools as they are considered as the one who can observer these impacts in a profound way. of the of Multan. Different areas of impacts have been analyzed in this study by using survey technique and analysis is conducted and presented in the teacher’s views in this study to examine what they feel that how cartoons are effecting the personalities of the children.

Recently, methods to detect DoS and spoofing attacks that occur on in-vehicle networks using CAN Protocol are being studied through deep learning models such as CNN, RNN, and LSTM. These studies have produced significant results in the field of In-Vehicle Network attack detection using deep learning models. In addition, significant results are being achieved through research on applying time series-based deep learning models such as LSTM to detect DoS attacks and replay attacks occurring in in-drone networks by expanding them to drones using the UAVCAN protocol. In this paper, we conducted an experiment to detect in-drone network attacks through non-time series analysis using machine learning models and deep learning models, and through appropriate learning for each attack type, it can also be analyzed through non-time series analysis. The results showed that it was possible to detect attacks.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

This paper presents the PEnsemble 4 model, a sophisticated machine learning framework that integrates IoT-based environmental data to accurately forecast maize yield. With the projected significant growth in global maize demand over the next decade, the inherent risks posed by the crop’s dependence on weather conditions necessitate improved prediction capabilities. The PEnsemble 4 model, developed with high accuracy, incorporates comprehensive datasets encompassing soil attributes, nutrient composition, weather conditions, and UAV-captured vegetation imagery. By employing a combination of Huber and M estimates, the PEnsemble 4 model effectively analyzes temporal patterns in vegetation indices, specifically CIre and NDRE, which serve as reliable indicators of canopy density and plant height. In addition, this research significantly contributes to precision agriculture by offering an efficient and sustainable alternative to conventional farming practices through precise yield predictions. Notably, the PEnsemble 4 model enables earlier estimation, advancing the timeline for yield prediction from the conventional day 100 in the R6 stage to day 79 in the R2 stage. This improvement enhances decision-making processes in farming operations. The remarkable accuracy rate of 91% underscores the importance of adopting a multifaceted data approach that harnesses IoT-derived environmental insights. Additionally, the PEnsemble 4 model extends its benefits beyond yield prediction, facilitating the detection of water and crop stress, as well as disease monitoring in broader agricultural contexts. Ultimately, the PEnsemble 4 model establishes a new standard in maize yield prediction, revolutionizing crop management and protection through the synergistic utilization of IoT and machine learning technologies.

This short communication reports on the initial results of a much larger, ongoing project, the aim of which is to investigate the question: could the skin microbiome, just like the gut microbiome, play a role in sports recovery and performance – and if so, could this role be as significant a one as that played by the gut microbiome? 17 high performance college athletes addressed their skin microbiome by minimizing contact with synthetic chemicals and by using topical skin supplements, shown previously to significantly increase skin microbiome biodiversity, for two weeks after training. 76% said their skin softness improved, 35% said their muscle stiffness and recovery after sport improved, 12% said their sleep quality improved, and 100% said they would be likely to use skin supplements again. Future work will use hundreds of athletes.

Although economic uncertainty and social media use are recognized as having a significant impact on religiosity, their role in religiosity has yet to be extensively examined in developing countries. This study explored the effects of economic uncertainty and social media use on religiosity in the Chinese context. By analyzing the publicly available data from the Chinese General Social Survey and World Values Survey, the findings showed that economic uncertainty significantly increased people's religious beliefs, while social media use had no significant impact on religious beliefs. Furthermore, social media use did not significantly moderate the relationship between economic uncertainty and religious belief. In contrast, educational level positively moderated the relationship between economic uncertainty and religious belief. These findings differ in part from the results of previous studies, presenting new evidence for theoretical integration in the field and revealing potential group differences in the strength of the relationship between economic uncertainty and religious belief.

The fast decoding of low-density parity-check (LDPC) is crucial for its future applications. In this paper, we propose to use Early Termination (ET) and Force Convergence (FC) techniques to accelerate the decoding of two new local/global two-phases decoding algorithms to reduce the Globally Coupled (GC) LDPC codes. Specifically, ET is applied in the local decoding phase of two- phases decoding of GC-LDPC codes to skip the local decoding which is highly likely to fail and avoid the unnecessary iterations. FC is applied in global decoding phase where converged variable nodes are identified and removed from Tanner graph and the decoding can be speed up shrinking parity check matrices. Two variants are proposed for the ET operation in local decoding phase. ET-1 merely stops iteration if it meets the stopping criterion while in ET-1, the iteration number saved in local decoding is added up in global decoding to improve the decoding performance. The simulation results show that the ET-1-FC scheme can save up to 42% decoding time complexity in the low SNR region while keeping the error rate performance nearly unchanged, the ET-2-FC can improve the error rate performance by 0.18dB at bit error rate 0.001 or 0.23dB at frame error rate 0.1. In the waterfalling region of BER/FER curves, both schemes can save about 25% decoding time complexity.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

This paper presents a novel approach to designing beam codebooks for downlink multiuser hybrid multiple input multiple output (MIMO) wireless communication systems, leveraging multi-agent reinforcement learning (MARL). The primary objective is to develop an environment-specific beam codebook composed of non-interfering beams, learned by cooperative agents within the MARL framework. Machine learning (ML) based beam codebook design for downlink communications have been based on channel state information (CSI) feedback or only reference signal received power (RSRP) consisting of an offline training and user clustering phase. In massive MIMO, the full CSI feedback data is of large size and is resource-intensive to process, making it challenging to implement efficiently. RSRP alone for a stand-alone base station is not a good marker of the position of a receiver. Hence, in this work, uplink CSI estimated at the base station along with feedback of RSRP and binary acknowledgment of the accuracy of received data is utilized to design the beamforming codebook at the base station. Simulations using sub-array antenna and ray-tracing channel demonstrate the proposed system’s ability to learn topography-aware beam codebook for arbitrary beams serving multiple user groups simultaneously. The proposed method extends beyond mono-lobe and fixed beam architectures by dynamically adapting arbitrary shaped beams to avoid inter-beam interference, enhancing overall system performance. This work leverages MARL’s potential in creating efficient beam codebooks for hybrid MIMO systems, paving the way for enhanced multiuser communication in future wireless networks.

The rheological properties of a polyamide (PA) resin with low crystallinity were modified by melt-mixing it with a small amount of an alternative a-olefin–maleic anhydride copolymer as a reactive compound. Because PA has a low melting point, rheological characterization was performed over a wide temperature range. Owing to the reaction between PA and the alternative a-olefin–maleic anhydride copolymer, the blend sample behaved as a long-chain branched polymer in the molten state. The thermo-rheological complexity was obvious owing to large flow activation energy values in the low modulus region. The primary normal stress difference under steady shear was greatly increased in the wide shear rate range, leading to a large swell ratio at capillary extrusion. Furthermore, strain hardening in the transient elongational viscosity, which is responsible for favorable processability, was clear. Because this is a simple modification method, it will be widely employed to modify the rheological properties of various polyamide resins.

Mutual exclusion algorithms are at the heart of concurrent, distributed/parallel, real-time and operating systems. It is well-known that such algorithms are very difficult to analyze and in the literature different conjectures about starvation-freedom and the number of by-passes (also said the overtaking factor), which in turn affects the (hopefully) bounded waiting time that a process competing for entering the critical section has to suffer before accessing the shared resource, have been formulated for specific algorithms. This paper proposes a novel modelling approach based on Timed Automata and the Uppaal toolset, which proves effective for studying all the properties of a mutual exclusion algorithm for N≥2 processes, by exhaustive model checking. Although the approach, as already confirmed by similar experiments reported in the literature, is not scalable due to state explosion problems, and can be practically applied until N≤5, it is of great value for revealing true properties of analyzed algorithms. For dimensions N>5 the statistical model checker of Uppaal can be used which, although based on simulations, can confirm properties by estimations and probabilities. The paper describes the proposed modelling and verification method and applies it to several mutual exclusion algorithms, thus retrieving known properties but also showing new results about properties often studied only by peer-review and intuitive reasoning.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

Establishing systemic communications between the project plan, stakeholders, and the organization through integrated management meets stakeholders' demands and managerial expectations in project-oriented organizations. Performance assessment can be defined as a control system in any company that reviews its daily operations and evaluates how well it has achieved its goals. This study aims to investigate the impact of an integrated project management system on the financial performance of the Organization for Renovation, Development, and Equipment of Schools. This applied research is descriptive-analytical. The statistical population comprises 2,700 employees of the organization, with a sample size of 340 individuals examined. The reliability of the designed questionnaire was confirmed by experts in the organization using Cronbach's alpha (α=0.91). Data were analyzed using SPSS version 20 and AMOS 18 software through descriptive statistics and confirmatory factor analysis. The results indicate that the seven dimensions of the integrated project management system (cost management, quality management and continuous control, change management, systems and information management, human resources management, interaction and communication management, procurement management) have a positive and significant impact on the financial performance of the Organization for Renovation, Development, and Equipment of Schools.

The performance of OpenFOAM in strong scaling tests on HPC systems with AMD EPYC processors exhibits a pronounced superlinear speedup. Simple test cases show superlinear speedups of over 300%, which significantly impacts the efficient use of computing resources. With the last generation of HPC architectures, a superlinear speedup of about 10% to 20% was well expected and accepted by CFD users. The measured superlinear speedup is much more pronounced and withstands the communication overhead to even larger scales. A detailed performance analysis of OpenFOAM follows, employing various High-Performance Computing (HPC) architectures, including AMD, ARM and Intel systems. The performance metric FVOPS (Finite VOlumes solved Per Second) is introduced to compare the performance of Computational Fluid Dynamics (CFD) applications when varying the grid size, as occurs in a strong scaling test. The achievable FVOPS depends on various factors, including the simulation type, boundary conditions, and especially the grid size of a use case. Analysing FVOPS on a single node level with varying grid size shows a significant difference in performance and cache utilization, which explains the large superlinear speedups seen in the strong scaling tests. Furthermore, FVOPS can be used as a simple benchmark to determine the optimal number of grid elements per rank to simulate a given use case at peak efficiency on a given platform, resulting in time, energy, and cost savings. The FVOPS metric also facilitates the direct comparison between different HPC architectures. The tests using AMD, ARM, and Intel processors show a peak in performance when employing around 10,000 grid elements per core. The presence of a large L3 cache on AMD processors is particularly advantageous, as indicated by L3 cache miss rates observed on AMD EPYC processors. Our results suggest that future HPC architectures with larger caches and higher memory bandwidth would benefit the CFD community.

With recent advancements in network technology and spread of Internet, use of social network services and Internet of Things devices has flourished, leading to a continuous generation of large volumes of graph stream data, where changes, such as additions or deletions of vertices and edges occur over time. Additionally, owing to the need for efficient use of storage space and security requirements, graph stream data compression has become essential in various applications. Even though various studies on graph compression methods have been conducted, most of them do not fully reflect the dynamic characteristics of graph streams and complexity of large graphs. In this paper, we propose a compression scheme using provenance data to efficiently process and analyze large graph stream data. It obtains provenance data by analyzing graph stream data and builds a pattern dictionary based on this to perform dictionary-based compression. By improving the existing dictionary-based graph compression methods, it enables more efficient dictionary management through tracking pattern changes and evaluating their importance using provenance. Furthermore, it considers the relationships among sub-patterns using an FP-tree and performs pattern dictionary management that updates pattern scores based on time. Our experiments show that the proposed scheme outperforms existing graph compression methods in key performance metrics, such as compression rate and processing time.

This study aimed to explore the fermentation behavior of selected potential probiotic strains during sorghum fermentation, considering their microbial counts, pH levels, and antibacterial activity, their ability to break down starch. The fermentation processes were conducted in the presence and absence of glucose, and the lactic acid bacterial strains underwent controlled fermentation to assess microbial counts, amylase activity, pH, and lactic acid levels in the presence and absence of glucose. In addition, the inhibitory activity of these potential probiotic strains against pathogenic bacteria (Salmonella typhimurium, Escherichia coli, and Staph-ylococcus aureus) was examined through co-culturing. The results demonstrated that all nine Lactobacillus strains exhibited robust growth in both sugar and sugar-free fermentation experiments. Glucose supple-mentation significantly enhanced lactic acid yield which was in a range of 0.19-0.52 % compared to fer-mentation without glucose with a range of 0.03-0.29 %. The selected Lactobacillus strains effectively lowered the pH to less than 4 after 24 hours, producing substantial lactic acid. Notably, in the absence of glucose, only Lb. helveticus D7 and Lb. amylolyticus D12 achieved pH levels below 4 after 8 hours, producing the highest lactic acid amounts of 0.27 and 0.29 % after 24 hours, respectively. Amylase activity was detected on two strains D7 and D12. Furthermore, most of the tested Lactobacillus strains demonstrated complete inhibition of pathogen growth after 24 hours of co-culturing, suggesting their potential for enhancing the safety quality of sorghum-based fermented products.

This article summarizes the results of a research conducted to create an intelligent platform supporting small farmers growing vegetables. In Bulgaria, many farmers use relatively small areas for their production. Considering this situation, the platform is designed for regional use, trying to make maximum use of the specific climatic features of the monitored microdistrict. Consequently, special attention is paid to the possibilities of adapting the platform to the specific environment in which the observed plants grow. Thus, the platform is implemented as an agent-oriented system providing needed flexibility. The core of the platform is a personal assistant, which is responsible for tracking the vegetation cycle of the monitored crop and, upon detection of anomalies, preparing warnings to the farmer. The general architecture of the platform is also presented. In a distributed knowledge base, agriculture-specific knowledge are stored. Furthermore, a standardized interface for receiving data from the sensor networks located in the production areas is briefly described. Currently, the platform is being tested for monitoring four varieties of tomatoes grown on the territory of the national research center for potato breeding. Special attention is paid to the measurements carried out. Conclusions have been drawn that will help improve the platform.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

The real systems are often complex, nonlinear, and noisy in various areas including mathematics, natural science, and social science. We present the symplectic entropy (SymEn) measure as well as an analysis method based on SymEn to estimate the nonlinearity of the complex system by analyzing the given time series. The SymEn estimation is a kind of entropy based on symplectic principal component analysis (SPCA) which represent organized but unpredictable behaviors of systems. The key to SPCA is to preserve the global submanifold geometrical properties of the systems through symplectic transform in the phase space, which is a kind of the measure-preserving transforms. The capability of preserving the global geometrical characteristics makes the SymEn a test statistic to detect the nonlinear characteristics in several typical chaotic time series and the stochastic characteristic in the Gaussian white noise. The results are in agreement with findings in the approximate entropy (ApEn), the sample entropy (SampEn) and the fuzzy entropy (FuzzyEn). Moreover, the SymEn method is also used to analyze the nonlinearities of the real signals (including the EEG signals for ASD and healthy subjects, and the sound and vibration signals for the mechanical systems). The results indicate that the SymEn estimation can be taken as a measure for describing the nonlinear characteristics in the data collected from the natural complex systems.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

Addressing escalating energy demands and greenhouse gas emissions in the oil and gas industry has driven extensive efforts in carbon capture and utilization (CCU), focusing on power plants and industrial facilities. Utilizing CO2 as a primary feedstock for industrial fuels and petrochemical materials offers a favorable alternative to sequestration, with byproducts substituting traditional chemical feedstocks. This comprehensive review explores the current landscape of CO2 capture technologies, examining opportunities, economic viability, and efficiency challenges. It provides a detailed analysis of various CO2 utilization methods and the combined process of capture and utilization. The review highlights primary obstacles in planning, production, and widespread implementation, emphasizing the need for strategic integration of materials research, process performance, and cost-effectiveness to advance new technologies.

This article will provide an overview on internet of things (IoT), 5G communication System and Distributed Clouds. The basic concepts and benefits will be briefly presented, along with current standardization activities. In a nutshell, but the research will focus on relating internet of things, 5G and Distributed Cloud Computing.

The early 2-factor (E2F) family of transcription factors, including E2F1-8, plays a critical role in apoptosis, metabolism, proliferation, and angiogenesis within glioblastoma (GBM). However, the specific functions of E2F transcription factors (E2Fs) and their impact on the malignancy of Bevacizumab (BVZ)-responsive GBM subtypes remain unclear. This study used data from The Cancer Genome Atlas (TCGA) and Gene Expression Omnibus (GEO) to explore the impact of eight E2F family members on the clinical characteristics of BVZ-responsive GBM subtypes and possible mechanisms of recurrence after BVZ treatment.To predict the possibility of GBM patient survival and progression, we classified and comparedthe expression of E2Fs according to BVZ-responsive subtypes and employed a machine learning method-TreeBagger, one random forest algorithm. Multiple bioinformatics analyses have shown that the significant increased E2F8 post BVZ treatment may enhance the function of angiogenesis and stem cell proliferation, indicating one of the mechanisms of GBM recurrence after treatment. In addition, BVZ treatment in unresponsive GBM patients may potentially worsen disease progression. Our findings suggest that E2F family members play important roles in GBM malignancy and BVZ treatment response, highlighting their potential as prognostic biomarkers and therapeutic targets and recommending precise BVZ treatment for GBM patients.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

BUB1 is overexpressed in most human solid cancers including breast cancer. Higher BUB1 levels are associated with poor prognosis especially in patients with triple-negative breast cancer (TNBC). Women with TNBC often develop resistance to chemotherapy and radiotherapy, which are still the mainstay of treatment for TNBC. Our previous studies demonstrated that BUB1 kinase inhibitor (BAY1816032) reduced tumor cell proliferation and significantly enhanced radiotherapy efficacy in TNBC. In this study, we evaluated the effectiveness of BAY1816032 with a PARP inhibitor (olaparib), platinum agent (cisplatin), and microtubule poison (paclitaxel) alone or in combination with radiotherapy using cytotoxicity and clonogenic survival assays. BUB1 inhibitor sensitized BRCA1/2 wild-type SUM159 and MDA-MB-231 cells to olaparib, cisplatin and paclitaxel synergistically (combination index; CI

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

This paper investigates the performance of dual hop UAV-assisted communication channels, employing a decode and forward relay architecture. The system utilizes Terahertz (THz) communication in the primary hop and Visible Light Communication (VLC) in the secondary hop. We conduct a thorough analysis by deriving closed-form expressions for end to end bit error rate (BER). Furthermore, we employ a Monte Carlo approach to generate best fitting curves and validate our numerical expressions with simulation results. Evaluation via BER and outage probability demonstrates the proposed system’s effectiveness. The outcomes of this research offer valuable insights into the feasibility and limitations of UAV-assisted THz- VLC systems.

The study of underwater vehicle wake detection is of significant importance within the field of target detection, localisation and tracking of underwater vehicles. Given that propellers are the propellers of modern ships and underwater vehicles, the propeller wake field represents the principal target source for wake detection in underwater vehicles. The objective of this paper is to propose a method for measuring the wake of an underwater propeller based on a position-sensitive detector. A theoretical model of the relationship between the laser spot displacement and the change of refractive index of the wake field is established on the basis of the principle of laser beam deflection. A prototype experimental setup for underwater propeller wake measurement was constructed based on the aforementioned optical measurement method. Furthermore, the simulation of the propeller wake flow field with strong density stratification and linear density stratification was conducted based on the experimental setup. In the experiment, a three-bladed propeller with a diameter of 39mm was selected, the water tank size was 980mm×380mm×380mm, and the laser acted at a distance of 550 mm from the propeller. The experimental results indicate that the wake dissipation time of the propeller in a strong density-stratified water environment is approximately 800s. Following the stabilization of the wake field density, the laser spot position is observed to be stable at 0.341 mm, with a corresponding refractive index change of 2.99×10-6 RIU. The wake dissipation time of the propeller in a linear density-stratified water environment is approximately 750 s. Once the wake field density has reached a stable state, the laser spot position is found to be 0.441mm, corresponding to a refractive index change of 3.87×10-6 RIU. These experimental results are found to be in general agreement with the simulation results of the propeller wake field. A comparison of the experimental device-based wake measurements with the CTD-based wake measurements reveals a consistent trend.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high-precision seawater refractive index measurements. A seawater refractive index measurement system based on position-sensitive detectors is an effective means to achieve high-precision measurement of seawater refractive index. However, in the actual seawater refractive index measurement process, the impact of the measurement error caused by the jitter signal obtained from the measurement on the measurement results cannot be ignored. In this paper, we theoretically analyse the causes of the long jitter signals during seawater refractive index measurement and quantify the influencing factors. Through the analysis, it can be seen that the angle between the two windows in the refractive index measurement area of seawater causes a great error on the measurement results, so the angle between the two windows should be controlled within 2.06° in order to effectively reduce the measurement error. At the same time, the factors affecting the measurement accuracy of the position-sensitive detector are analysed, and the factors leading to the reduction of the measurement accuracy of the position-sensitive detector are mainly the background light, the size of the photosensitive surface, and the change of the temperature of the working environment. For the above factors, we add a narrow-band filter with a bandwidth of 0.9nm in front of the photosensitive surface of the position-sensitive detector during the construction of the measurement system, so as to filter out stray light other than the signal light source. On the premise of ensuring the measuring range of the refractive index of seawater, a position-sensitive detector with a photosensitive surface size of 4 mm×4 mm was selected. In order to reduce the temperature variation of the working environment of the position-sensitive detector, the measurement system was partitioned. In order to validate the testing error range of the optimised test system, standard seawater samples under the same conditions were measured. It can be seen that the jitter signal of the measurement system has been reduced from 0.0022mm before the optimisation to 0.0011mm after the optimisation, and the deviation of the refractive index has been reduced by 1.09×10−8RIU. The experimental results show that the refractive index of seawater has been effectively reduced by adjusting the optical path and the structure of the seawater refractive index measurement system.

This research presents the Cross-Cultural Intelligent Language Learning System (CILS), a novel approach integrating Artificial Intelligence (AI) into language education to enhance cross-cultural communication. CILS utilizes advanced AI technologies to provide adaptive, personalized learning experiences that cater to the unique linguistic and cultural backgrounds of each learner. By dynamically adjusting content and methodology, CILS significantly improves linguistic proficiency and cultural understanding, essential for effective global interactions. The implementation of CILS in platforms such as Busuu and HelloTalk has demonstrated marked improvements in engagement and communication skills among learners. Empirical studies validate the system's effectiveness in real-world settings, showing enhanced learner performance and increased intercultural competence. Additionally, the Technology Acceptance Model (TAM) applied confirms that the usability and perceived usefulness of AI-driven systems strongly influence learner acceptance and sustained use. This study not only underscores the potential of AI in transforming language education but also highlights the critical role of cultural sensitivity in designing educational technologies.

Previous research on the relative benefits of Augmentative and Alternative Communication Systems (AACs) has indicated controversial results regarding the effectiveness, the ease of use, and the preference for the different systems. The study aims to observe the comparative effectiveness of two different Augmentative and Alternative Communication (AAC) tools, the Picture Exchange Communication System (PECS) and a speech-generating device (SGD), as communication aids for children with autism. Three children with severe autism and minimally verbally or with no functional language participated. The results showed an increase of communicative behavior with both AAC intervention strategies and a speed acquisition time slightly shorter for the SGD training. Two of the three participants showed a preference for the use of the SGD. Reduction in problem behaviors and improvement in vocal production was observed for one of the participants. Results suggest that PECS and SGD are similarly appropriate for the development of initial request skills and that they can encourage vocal production in students with specific prerequisites.

Objectives: To compare the effects of high-velocity resistance training to slow-velocity re-sistance training on neuromuscular and functional parameters and to analyze the relationship between changes in walking speed and improvements in neuromuscular parameters following intervetions. Methods: 40 participants were randomly assigned to either a high-speed resistance training group (GHS, n = 18; age = 80.41 ± 10.12 years; BMI = 23.81 ± 3.45 kg/m²) or a low-speed resistance training group (GLS, n = 22; age = 82.89 ± 5.32 years; BMI = 23.81 ± 3.45 kg/m²). Before and after the interventions, gait speed (m/s) was assessed using a 10-minute walking test, and relative maximal force (Relative F max, N/kg) was evaluated during maximal voluntary isometric con-traction of the plantar flexors. From the force-time curve, early (0 – 50 ms) and late (100 – 200 ms) rates of force development (RFD) were extracted from the linear slopes (Δ force / Δ time). Results: Gait speed significantly improved in both groups (p < 0.05). However, the improvement was more pronounced in the GHS compared to the GLS (p < 0.05). Relative Fmax showed a more significant increase in the GLS than in the GHS (p < 0.05). Moreover, a significant 10% increase in early RFD in the GLS and a 20.1% increase in the GHS were observed (p < 0.05). The improvement in early RFD was greater in the GHS (p < 0.05). Additionally, late RFD improved significantly only in the GHS (+20.4%, p < 0.05). Conclusion: High-velocity resistance training appears particularly effective in improving the ability to rapidly generate force, which is essential for many daily activities re-quiring explosive movements and quick responses.

In the United States, several land use and land cover (LULC) data sets are available based on Landsat. These data sets often fail to accurately represent the features on the ground despite having several advantages over other data. Detailed mapping of complex heterogeneous landscapes for informed decision-making is possible using high spatial resolution orthoimagery from the National Agricultural Imagery Program (NAIP). However, large-area mapping at this resolution remains challenging due to radiometric differences between scenes, low spectral depth of imagery, landscape heterogeneity, and computational limitations. Machine learning (ML) techniques have shown promise in improving LULC maps. The primary purposes of this study are to examine and evaluate bagging (Random Forest; RF), Boosting (Gradient Boosting Machines [GBM] and Extreme Gradient Boosting [XGB]), and stacking ensemble models on sentinel 2A fusion data on NAIP imagery. We also compared the accuracy based on random cross-validation (80% / 20% split) without accounting for spatial autocorrelation and target-oriented validation (10 clusters) accounting for spatial structures of the training data set. To make the LULC map of a portion of Tom Green and Irion counties in central Texas, we used a time series of sentinel data and NAIP orthoimagery. We created several spectral indices, structural variables, and geometry-based variables, reducing the dimensionality of features generated on Sentinel and NAIP data. The random and target-oriented validation results show that autocorrelation in the training data offers over-optimistic results. In our case, the overestimation ranged from 2 % to 3.5 %. The XGB-boosted stacking ensemble on-base learners (RF, XGB, and GBM) improved model performance over individual base-learner. The main contribution of this research is that meta-learners are just as sensitive to overfitting as base models, as these algorithms are not designed to account for spatial information. Finally, we show that the fusion of Sentinel 2A data with NAIP data improves land use land cover classification using Geographic Object-Based Image Analysis (GEOBIA).

One of the most crucial elements in deeply understanding humans on a psychological level is manifested through facial expressions. The analysis of a human behavior can be informed by their facial expressions, making it essential to employ indicators such as expression (Expr), valence-arousal (VA), and action units (AU). In this paper, we introduce the method proposed in the Challenge of the 6th Workshop and Competition on Affective Behavior Analysis in-the-wild (ABAW) at CVPR 2024. Our proposed method utilizes the multi-modal Aff-wild2 dataset, which is splitted into spatial and audio modalities. For the spatial data, we extract features using a SimMiM model that was pre-trained on a diverse set of facial expression data. For the audio data, we extract features using a WAV2VEC model. To fusion the extracted spatial and audio features, we employed the cascaded cross-attention mechanism of a transformer.

In this paper, we introduce a novel controlled quantum communication protocol utilizing a quantum random walk involving one sender, one receiver, and multiple controllers. Inspired by classical random walk theory, quantum random walk serves as the foundation of our proposed protocol. With this protocol, we demonstrate the ability to transfer any n- dimensional quantum state to any party facilitated by any m number of controllers. Furthermore, any of the (m+1) individuals has the freedom to accept the role of the receiver. Rigorous testing of the protocol’s performance is conducted through quantum state tomography. We have run different variations of the circuits in IBMQ QASM simulator. Additionally, we explore the effectiveness of a weak measurement-based protocol designed to mitigate amplitude-damping noise’s detrimental effects on quantum states. By analyzing fidelity versus amplitude damping noise-strength plots for scenarios with and without the weak measurement protocol, we provide valuable insights into its protective capabilities across various levels of noise. These find- ings illuminate the protocol’s potential applications in quantum information processing

As a representative of Exponential Organizations, MI went from obscurity to the Fortune 500 in just ten years. Mi's success is inextricably linked to its outstanding business model. This paper summarizes the elements of MI's business model from four perspectives: value proposition, value creation, value delivery, and value capture, as well as its measures for developing into an exponential organization. Expecting to provide theoretical references for the transformation and upgrading of manufacturing organizations.

This paper explores the capability of various machine learning algorithms, including Random Forests and advanced gradient boosting techniques such as XGBoost, LightGBM, and CatBoost, to predict customer churn in the telecommunications sector. For this analysis, a dataset available to the public was employed. The performance of these algorithms was assessed using recognized metrics, including Accuracy, Precision, Recall, F1-score, and the Receiver Operating Characteristic Area Under Curve (ROC AUC). These metrics were evaluated at different phases: subsequent to data preprocessing and feature selection; following the application of SMOTE and ADASYN sampling methods; and after conducting hyperparameter tuning on the data that had been adjusted by SMOTE and ADASYN. The outcomes underscore the notable efficiency of upsampling techniques such as SMOTE and ADASYN in addressing the imbalance inherent in customer churn prediction. Notably, the application of random grid search for hyperparameter optimization did not significantly alter the results, which remained comparatively unchanged. The algorithms' performance post- ADASYN application marginally surpassed that observed after SMOTE application. Remarkably, LightGBM achieved an exceptional F1-score of 89% and an ROC AUC of 95% subsequent to the ADASYN sampling technique. This underlines the effectiveness of advanced boosting algorithms and upsampling methods like SMOTE and ADASYN in navigating the complexities of imbalanced datasets and intricate feature interdependencies.

The availability rating of any system is the probability that it will be able to operate for a given time in other words, to restore the system in the case of a system failure, or during the failure it is a measure of the availability index of resource system. We aimed to complete the study for the reasons as below. The rating and upgrading of underground mine radio communication system availability is to ensure operation reliability of the underground mine and to establish reliable radio communication system for miner’s safety during failure. Therefore, our study is contributed to reveal system availability rating of single resource (with two parallel connections) system and two resources (with three parallel connections) system. The study is related to not only practical contribution but also reliability engineering theory. To achieve this result, we have used Exponential, Weibull, and Poisson distributions. The readiness rating of single resource (with two parallel connections) and two resources (with three parallel connections) systems were calculated using Matlab software and the simulation results were introduced. This result confirms that any system has a resource system, which increases its readiness rating. The study was in examples of single resource radio communication system on the two shafts of the underground mine and two resource radio communication system for three shafts. During the initial system reliability enhancement study, the readiness of the dual resource system was assessed. The rating shows a 99 percent result, which is very meaningless for systems with more than two n-resources and we have revealed that it can show more than 100 percent result. In the process of the study on system reliability improvement the rating availability of system which has two resources was 99 % result. It is very meaningless for systems with more than two n-resources or more than 100% result.

Optical wireless communication is a promising emerging technology that addresses the limitations of radio-frequency-based wireless technologies. This study presents a novel hybrid modulation for optical camera communication (OCC); it integrates two waveforms transmitted from a single transmitter light-emitting diode (LED) and received by two rolling-shutter camera devices. Then, a smart camera with a high-resolution image sensor captures the high-frequency signal, and a low-resolution image sensor from a smartphone camera captures the low-frequency signal. Through this hybrid scheme, two data streams are transmitted from a single LED lamp; this reduces the cost of the indoor OCC device compared to one that transmits two signals from two different LEDs. In proposed scheme, rolling-shutter orthogonal frequency-division multiplexing is used for the high-frequency signals, and M-ary frequency-shift keying is used for the low-frequency signals in the time domain. This proposed scheme is compatible with smart phone camera and USB camera. By controlling the OCC parameters, the hybrid scheme can be implemented with high performance for a communication distance of 10 m.

When an earthquake or a large fire has occurred, it is difficult to secure communication networks for rescue in the building due to the destruction of commercial communication networks. Although analog radio systems such as VHF (very high frequency) and UHF (ultra-high frequency) are used for rescue operation in general, communication failure occurs in closed spaces, causing difficulties in smooth rescue operations. When the communication infrastructures have been destroyed in a building in the disaster, an emergency wireless telecommunication environment should be constructed to secure a safer disaster response environment. In this study, along with comparison of the performances of diverse communication frequencies, UWB (Ultra-Wide Band) wireless telecommunication networks were evaluated under five building indoor environment conditions including open spaces. UWB communication modules were fabricated to satisfy the IEEE (The Institute of Electrical and Electronics Engineers) 802.15.4a standard performance to measure distances in which communications are possible according to the indoor environment for each of six channels with different UWB communication frequencies. The results indicated that the distances in which communications are possible for each the six channels were average 15.5 m, maximum 20 m in open spaces; average 17.33 m, maximum 20 m in corridors; average 15.3 m, maximum 20 m in indoor office environments with office fixtures; average 4.33 m, maximum 6 m in vertical spaces of stairs; and average 6.5 m, maximum 17 m in closed horizontal spaces with a fire door. In this case, the communication performance and distance performance were shown to be the most excellent at a frequency (Centre Frequency) of 6489.6 and a band of 5980.3 – 6998.9 MHz, which is UWB 7ch. In conclusion, it is judged that if UWB communication modules are installed in the disaster area at intervals of 20 m and multi-channels are used, communication environments can be constructed even in closed spaces

In order to explore more spectrum resources to support sensors and its related applications, cognitive wireless sensor networks (CWSNs) have emerged to identify available channels being underutilized by the primary user (PU). To improve the detection accuracy of the PU signal, cooperative spectrum sensing (CSS) among sensors paradigm is proposed to make a global decision about the PU status for CWSNs. However, CSS is susceptible to Byzantine attack from malicious sensor nodes due to its open nature, resulting in wastage of spectrum resources or causing harmful interference to PUs. To suppress the negative impact of Byzantine attack, this paper proposes a beta distribution function (BDF) for CSS among multiple sensors, which includes a sequential process, beta reputation model, and weight evaluation. Based on sequential probability ratio test (SPRT), we integrate the proposed beta reputation model into SPRT, while improving and reducing the positive and negative impacts of reliable and unreliable sensor nodes on the global decision, respectively. Finally, the numerical simulation results demonstrate that compared to SPRT and weighted sequential probability ratio test (WSPRT), the proposed BDF has outstanding effects in terms of the error probability, and average number of samples under various attack ratios and probabilities.

Studies have shown that vehicle trajectory data are effective for calibrating microsimulation mod-els. Light Detection and Ranging (LiDAR) technology offers high-resolution 3-D data, allowing for detailed mapping of the surrounding environment, including road geometry, roadside infrastruc-tures, and moving objects such as vehicles, cyclists, and pedestrians. This research presents a comprehensive framework for integrating LiDAR sensor data into simulation models and accu-rately calibrating for proactive safety analysis. Vehicle trajectory data were extracted from LiDAR point cloud collected at six urban signalized intersections in Lubbock, Texas in USA. Each study intersection was modelled with PTV VISSIM and calibrated to replicate the observed field scenarios. The Directed Brute Force method was used to calibrate two car-following and two lane-change parameters of Wiedemann 1999 model in VISSIM, resulting in an average accuracy of 92.7%. Rear-end conflicts extracted from the calibrated models combined with a ten-year historical crash dataset were fitted into a Negative Binomial (NB) model to estimate the model's parameters. In all the six intersections, rear-end conflict count is a statistically significant predictor (p-value < 0.05) of observed rear-end crash frequency. The outcome of this study provides a framework for the com-bined use of LiDAR-based vehicle trajectory data, microsimulation and surrogate safety assessment tools to transportation professionals for proactive safety evaluation.

The burden of hypertension remains unacceptably high globally, particularly in low- and middle-income countries (LMICs). Workplace offer enormous potential as an idea setting for early detection and treatment of hypertension among the working class. Analysis of such a Workplace Screening Programme can reveal information about its potential impact. Machine learning techniques such as k-Means Clustering are untapped tools for such analyses. We set out to deploy this tool for the analysis of our university annual medical screening of workforce for hypertension. An anonymized dataset containing the demography and blood pressure measurements values obtained from staffs of different departments/units in an academic institution was obtained. The total number of samples or data points are 1, 723 in which the input dataset contains six features, including year category (2018, 2019, 2021,2022), Department/Unit (academic and non-academic), gender (male and female), while the target output is the blood pressure status (low, normal and high) respectively. Analysis of the dataset was carried out using machine learning techniques. In this retrospective analysis, it was observed that the mean age for this working class is 42 years old. Similarly, it was discovered that hypertension was prevalent among members of staff above the age of 40 irrespective of their gender or professional category (academic or non-academic). The analysis also revealed that there was a steady decline in the prevalence of hypertension from 2018 to 2022. From the research, it is evident that the adoption of machine learning techniques for periodic analyses of workplace health status screening initiative (especially for hypertension) is effective, feasible, and sustainable to diagnose and control hypertension among the working class.

Starting from the fact that one of the global control strategies of the Permanent Magnet Synchronous Motor (PMSM), namely the Direct Torque Control (DTC) type control strategy, is characterised by the fact that the inner flux and torque control loop usually uses hysteresis ON-OFF type controllers and the oscillations introduced by them have to be cancelled out by the outer speed loop controller (which is usually a PI speed controller and whose performance is good around the global operating points and for relatively small variations of the external parameters and disturbances caused in particular by the load torque variation), while retaining the advantages of the DTC strategy, this paper presents the improvement of the performance of the PMSM sensorless control system using Proportional Integrator (PI), PI Equilibrium Optimizer Algorithm (EOA), Fractional Order (FO) PI, Tilt Integral Derivative (TID) and FO Lead-Lag for constant flux, and Sliding Mode Control (SMC) and FOSMC for variable flux. The performance indicators of the control system are the usual ones: response time, settling time, overshoot, steady-state error and speed ripple, plus another one given by the fractal dimension (FD) of the PMSM rotor speed signal, and the hypothesis that the FD of the controlled signal is higher when the control system provides better performance is verified. The paper also presents the basic equations of the PMSM, based on which the synthesis of integer and fractional controllers, the synthesis of an observer for estimating the PMSM rotor speed, electromagnetic torque and stator flux are presented. The comparison of the performance of the proposed control systems and the demonstration of the parametric robustness are performed by numerical simulations in Matlab/Simulink using Simscape Electrical and Fractional Order Modelling and Control (FOMCON). Real-time control based on an embedded system using a TMS320F28379D controller demonstrates the good performance of the PMSM sensorless control system based on the DTC strategy in a complete hardware-in-the-loop (HIL) implementation.

Dengue infection is caused by the Dengue virus (DENV) and is transmitted to humans by infected female Aedes aegypti and Aedes albopictus mosquitoes. There are nearly 100 million new dengue cases yearly in more than 120 countries with a five-fold increase in incidence over the past four decades. While many patients experience a mild illness, a subset suffer from severe disease which can be fatal. Dysregulated immune responses are central to the pathogenesis of dengue, and haematologic manifestations are a prominent feature of severe disease. While thrombocytopaenia and coagulopathy are major causes of bleeding in severe dengue, leucocyte abnormities are emerging as important markers of prognosis. In this review, we provide our perspective on the clinical aspects and pathophysiology of haematologic manifestations in dengue. We also discuss the key gaps in our current practice and areas to be addressed by future research.

Sarcopenia is associated with clinical complications, which increase mortality. Effective sarcopenia risk screening in the elderly should be grounded in a comprehensive assessment, encompassing both nutritional status and medication use. Current screening tools, while emphasizing muscular per-formance, exhibit limited sensitivity in identifying elderly individuals at risk of sarcopenia. This cross-sectional study aimed to develop a sarcopenia risk screening tool, named Sarc-Global, with enhanced sensitivity, incorporating factors pertinent to the overall health of the elderly. Utilizing the criteria established by EWGSOP2 for diagnosing sarcopenia, we evaluated 395 communi-ty-dwelling elderly individuals. This evaluation served as a reference for assessing the efficacy of two validated questionnaires, Sarc-F and Sarc-CalF, and our newly developed Sarc-Global. Con-structed through multiple logistic regression, Sarc-Global integrates variables such as sex, age, medication use, body mass index, arm circumference, and handgrip strength – all significantly associated with sarcopenia (p

Recently, various research has been developed addressing communication sensors for Unmanned Aerial Systems (UASs); especially when pondering control difficulties, communication is a crucial component. To this end, strengthening a control algorithm with redundant linking sensors ensures the overall system works accurately even if some components fail. This paper proposes a novel approach to integrate several sensors and actuators for a heavy Unmanned Aerial Vehicle (UAV). Additionally, a cutting-edge Robust Thrust Vectoring Control (RTVC) technique is designed to control various communicative modules during a flying mission and converge the attitude system to stability. The results of the study demonstrate that even though RTVC is not frequently utilized, it works as well as cascade PID controllers, particularly for multi-rotors with mounted flaps, and could be perfectly functional in UAVs powered by thermal engines to increase the autonomy since the propellers cannot be used as controller surfaces.

Machine Learning (ML) and Artificial Intelligence(AI) have revolutionized almost all fields that are linked to the acquisition of intelligent behavior in the real world. It is an attractive alternative for a researcher of artificial intelligence. Contrary to rule-based programming, ML is an algorithmic approach in which learning comes from existing data. The more data we have these computer systems look at, we say we’re ‘training’ the computer system, and as the computers begin to identify patterns in the data, identify abnormalities in the data from these abnormalities we improve the system architect according to the requirement. This article introduces the use of comprehensive concepts of machine learning, in general, particular, and their potential applications in communications. Furthermore, the current state and futuristic potentials of enabling universal communication with implications of machine learning methods have been explained. In this review paper, we offer a comprehensive talk on distinctive methods/techniques of information analytics, artificial intelligence (AI), and machine learning (ML) moved forward the contact aware communication system.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

Prostate cancer is the second leading cause of death in males in America, with advanced prostate cancers exhibiting a 5-year survival rate of only 32%. Castration-resistance is often developed during the course of treatment, though its influences require further understanding. This study explores the human microbiome for its implications in castration-resistance and metastasis in prostate cancer. RNA sequencing data was downloaded for bone and soft tissue biopsies of patients with metastatic castration-resistant prostate cancer. These sequences were mapped to bacterial sequences to yield species-level abundance approximations. Numerous species were found to correlate to the expression of known markers of castration-resistance, including AR, PI3K, and AKT. Castration-resistance-associated signaling pathways were also enriched with these species, including PI3K-AKT signaling and endocrine resistance. For their implications in cancer aggression and metastasis, cancer stem cell markers were further explored for relation to these species. EGFR and SLC3A2 were widely downregulated with greater abundance of most species. Our results suggest that the microbiome is heavily associated with castration-resistance and stemness in prostate cancer. By considering the microbiome’s importance in these factors, we may better understand the highly aggressive and highly invasive nature of prostate cancer, allowing for needed improvement in the treatment of this disease.

In this paper, the entire downhole fluid sucker rod pump system is replaced with a viscoelastic vibration model, namely a third-order differential equation with an inhomogeneous forcing term. Both Kelvin and Maxwell viscoelastic models can be implemented along with the dynamic behaviors of a mass point attached to the viscoelastic model. By employing the time-dependent polished rod force measured with a dynamometer as the input to the viscoelastic dynamic model, we have obtained the displacement responses, which match closely with the experimental measurements in actual operations, through an iterative process. The key discovery of this work is the feasibility of the so-called inverse optimization procedure which can be utilized to identify the equivalent scaling factor and viscoelastic system parameters. The proposed Newton-Raphson iterative method with some terms in the Jacobian matrix expressed with averaged rates of changes based on perturbations of up to two independent parameters provides a feasible tool for optimization issues related to complex engineering problems with mere information of input and output data from either experiments or comprehensive simulations. The same inverse optimization procedure is also implemented to model the entire fluid delivery system of a very viscous non-Newtonian polymer modeled as a first-order ordinary differential system similar to the transient entrance developing flow. The convergent parameter reproduces transient solutions which match very well with those from full-fledged computational fluid dynamics models with the required inlet volume flow rate and the outlet pressure conditions.

Abstract: This study investigates the transition to sustainable shipping industry within the framework of the IMO's 2050 carbon neutrality objective, focusing on socio-technical systems analysis. The research delves into the sustainable paradigm shift towards alternative marine fuels such as LNG, methanol, ammonia, and hydrogen from a socio-technical transition perspective, analyzing the multi-level per-spective challenges and opportunities. Specifically, it scrutinizes the implications of adopting these al-ternative fuels for global shipping, identifying technical uncertainties, financial constraints, and infra-structure needs. Through a comprehensive review of existing literature on ship emissions and alterna-tive fuels, coupled with socio-technical transition theory, the study addresses the multifaceted chal-lenges and opportunities in meeting the IMO's environmental objectives. It emphasizes the necessity of collaborative governance, innovative niche strategies, and a holistic approach to leverage the current window of opportunity in facilitating the maritime industry's transition to sustainable fuel options. Fi-nally, this research enhances our understanding of the intricate interplay between technological, social, industrial, and cultural dynamics in the greening of shipping and offers insights into the strategic adop-tion of environmentally friendly marine fuels for a sustainable future.

The deaf impairment is among the most substantial health problem worldwide, that can lead to various personal, economical, and social crisis. Therefore, it is critical for developing an efficient way to facilitate communication between deaf-dumb impaired and normal people. Herein, we have rationally designed a new digitally computerized and mobile smart system as an efficient communication tool between deaf impaired and normal Arabian people. This is based on two main steps, including creating a digital output for the hand gestures using gloves flex sensors equipped with a three-axis accelerometer that is controlled using a microcontroller. The digital results are compared to that in a words-based “database”, where Arabs use expressions not alphabet in their communication. The second step is translation or conversion the outputs of the first stage into written texts and voices. The newly developed system allows Arabian deaf to translate words of ordinary people into gestures using a speech recognition system with an impressive accuracy over 90 % without the needing for a webcam, colored gloves, and/or online translator. The presented system can be used on any android or windows.

The LED light source is an important light source for indoor visible light communication. It has the characteristics of a large divergence angle and a high transmission rate. Therefore, using LED as the light source for visible light full-duplex communication can not only satisfy the lighting requirements but also transmit information at high speed. To analyze the factors that affect the optical power of the indoor single-light source visible light communication uplink receiving end, an indoor visible light communication model was established, and mathematical calculation formulas were derived based on the model establishment, and the maximum movable range formula of the retroreflective end under specific conditions was derived; The reliability of the formula was verified with the help of Zemax simulation software. Theoretical analysis and experimental results show that increasing the movement range of the retroreflective end can be achieved by increasing the lens diameter, reducing the focal length, and increasing the link distance.

Enabling D2D communication in the mm-Wave band has many obstacles which must be mitigated. The primary concern is the introduction of interference from various sources. Thus, we focused our work on the performance of decode and forward (DF) relay assisted D2D communication in the mm-Wave band for increasing the coverage probability and energy efficiency (EE). Three modes are proposed for D2D communication to prevail. Bit-wise binary XOR operation is executed at the relay node which increases the security feature. Radius of coverage expression is derived which indicates the switching of the modes. The diffused incoherent scattering power is also considered as a part of power consumption. Furthermore, a unique relay selection scheme, Dynamic relay selection (DRS) method is proposed to select the optimal relay for information exchange. Comparison of the proposed DF relay scheme with amplify and forward (DF) scheme is also shown. Finally, simulation results prove the efficacy of the proposed work.

Studies show that although female soccer players often have shorter change of direction (COD) deficits than males, indicating different biomechanical profiles, there is lack of research on the impact of physical metrics on COD performance in females. The aim of this study was to analyze whether performance metrics based on speed, and jumping could explain the variation in %CODD in young female soccer players. Thirty-three highly trained adolescent female soccer players (age: 16. ± 0.95 years; height: 160.4 ± 5.22 cm; body mass: 55.7 ± 7.22 kg) performed COD180 tests, 10-m and 30-m sprint test and single leg countermovement and horizontal jumps. Acceleration in the first 10 meters of a sprint was identified as a significant predictor of COD180 performance (R2 = 28%), (R2 = 50%), (p