In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

Imitation learning, also known as programming by demonstration, has been shown to be a promising paradigm for intuitive robot programming by non-expert users. However, the classical kinesthetic approach with physical hand guidance suffers from generalizability across different robot types and is impractical for demonstrating tasks with long horizons. Visual imitation learning enables the recording of multi-step tasks as a single continuous video, allowing non-experts to demonstrate tasks naturally. Existing approaches typically require a large amount of data to develop end-to-end deep learning models that map raw pixels to robot actions. This paper explores the application of visual imitation learning from one-shot demonstration, significantly reducing the data requirements and simplifying the programming process. To achieve this target, a framework is proposed to map hand trajectories to the robot end-effector, consisting of four essential components: hand detection; object detection; segmentation of the trajectories into elemental skills; and learning the skills. Methods are developed for each component and evaluated on recorded videos to demonstrate the effectiveness of the proposed framework.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

Fabrics comprised of porous fibers could provide effective passive protection against chemical and biological (CB) threats whilst maintaining high air permeability (breathability). Here, we fabricate hierarchically porous fibers consisting of regenerated silk fibroin (RSF) and activated-carbon (AC) prepared through two fiber spinning techniques in combination with ice-templating – namely cryogenic solution blow spinning (Cryo-SBS) and cryogenic wet-spinning (Cryo-WS). The Cryo-WS RSF fibers had exceptionally small macropores (as low as 0.1 µm) and high specific surface areas (SSAs) of up to 79 m2 g-1. The incorporation of AC could further increase the SSA to 210 m2 g-1 (25 wt. % loading) whilst also increasing adsorption capacity for volatile organic compounds (VOCs).

The structure of self-reinforced composites (SRCs) based on ultra-high molecular weight 21 polyethylene (UHMWPE) was studied by means of Wide-Angle X-Ray Scattering (WAXS), X-Ray 22 tomography, Raman spectroscopy, Scanning Electron Microscopy (SEM) and in situ tensile testing 23 in combination with advanced processing tools like Avizo, ImageJ, and Ncorr to determine the cor-24 relation between the processing conditions, on the one hand, and the molecular structure and 25 mechanical properties, on the other. SRCs were fabricated by hot compaction of UHMWPE fibers at 26 different pressure and temperature combinations without addition of polymer matrix or softener. 27 It was found by WAXS that higher compaction temperatures led to more extensive melting of 28 fibers with the corresponding reduction of the Herman’s factor reflecting the degree of molecular 29 orientation, while the increase of hot compaction pressure suppressed the melting of fibers within 30 SRCs at a given temperature. X-Ray tomography proved the absence of porosity while polarized 31 light Raman spectroscopy measurements for both longitudinal and perpendicular fiber orienta-32 tions showed qualitatively the anisotropy of SRC samples. SEM revealed that the matrix was 33 formed by interlayers of molten polymer entrapped between fibers in SRCs. Moreover, in situ 34 tensile tests demonstrated the increase of Young’s modulus and tensile strength with increasing 35 temperature.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

This work aims to investigate the impact of chemical treatment of Juncus acutus fibers on the hygric and mechanical performances of an innovative bio-sourced clay-sand-Juncus acutus fibers composite. This lightweight specimen has been produced from a mixture of 60 % natural clay and 40 % sand by mass, as a matrix, and reinforced with different amounts of Juncus fibers. The fibers were used as a partial replacement of sand in mixture by volume at 0 % (Control Specimen), 5 %, 10 %, and 20 %. In order to enhance the fiber-matrix interfacial bound, the raw fibers have undergone an NaOH alkali treatment with different concentrations of 1, and 2 wt. %. Morphological and mineralogical evaluation based on SEM micrographs and EDX analyses revealed that, the alkaline concentration of 1 wt. % is the optimized one for natural fiber surface modifications (removal of impurities without any surface damage). This optimal concentration is confirmed by tensile strength tests, showing that the treated fibers with this alkali solution presents the higher tensile stress value of 81.97 MPa, compared to those of treated fibers with 2 % NaOH (74.45 MPa), and the untreated fibers (70.24 MPa). However, mechanical test-results highlighted the benefit effect of the fiber alkali treatment on both the compressive and flexural strengths, particularly for fiber contents of 5 % and 10 %, which corresponds to a strengthening rate of 25 % and 30 %, respectively. Results also showed that the sample containing treated fibers exhibited a better moisture regulating property than that produced with untreated fibers. The specimens are classified as excellent hygric regulator based on their moisture buffer performance (MBV > 2 g/(m2.%RH)), according to NORDTEST classification. Results also indicated that the capillary water absorption and the apparent moisture diffusivity of composites was lowered due to high fiber-matrix interfacial bound, after fiber treatment. Consequently, the composite with treated fibers is less diffusive compared to that with untreated fibers, and thus expected to be more durable in a humid environment. These results were confirmed by morphological analysis of fibers-matrix interfacial transition zone.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

There are various types of charged particles in the space environment, which can cause different types of radiation damage to materials and devices, leading to on-orbit failures and even accidents of spacecraft. Developing lightweight and efficient radiation shielding materials is an effective approach to improve the inherent protection of spacecraft. The protective performance of different materials against proton and electron spectra in the Earth’s radiation belts is evaluated by Geant4 simulation. Based on the simulation results, suitable hardening components are selected to design composite materials, and B4C/PEEK composites with different B4C content were successfully prepared. Experimental results demonstrate that the simulated and experimental results for the electron, proton and neutron shielding performance of B4C/PEEK composites are consistent. These composites exhibit excellent radiation shielding capabilities against electrons, protons and neutrons, and the radiation protection performance improves with increasing B4C content in the B4C/PEEK composite materials.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

Nanomaterials have shown significant promise for enhancing the performance of composite materials and increasing their functionality for various industrial applications. This review explores the unique properties of nanomaterials, particularly carbon-based nanomaterials, and provides key findings in utilizing them to enhance composite performance. It highlights specific nano-based composite materials and their significant potential in advancing the field of nanocomposites. Challenges associated with nanocomposite production and utilization are also discussed, along with possible solutions to address them. Finally, the study provides recommendations for continued research and innovation in nanocomposites to fully unlock the benefits of these advanced materials for broader future applications.

The behavior of concrete beams reinforced with steel and Glass Fiber Reinforced Polymer (GFRP) rebars, without shear reinforcement is investigated in the current study. This study includes testing experimentally of twenty-four steel and GFRP Reinforced Concrete (RC) beams cast with different percentage of fibers. The beams were split into two types, steel and GFRP RC beams. Beams of different fiber ratios (0, 0.5, 1.5 and 2.5%) were developed and tested, in two groups, each consists of twelve specimens, steel and GFRP reinforced RC beams. Both steel and GFRP RC beams were cast as singly reinforced with 10 mm diameter longitudinal bars at the bottom. In order to ensure that the beam to fail under shear, the top reinforcement and stirrups are removed. The concrete cover was kept as 30 mm. Three concrete grades (M30, M60 and M80) were examined for different dosage of fibers for both steel and GFRP RC beams. The size of the beam samples was kept as 150 ×200×1500 mm. The key parameters were the form of reinforcement material (steel and GFRP), compressive strength of concrete and fiber percentage. Failure mode, ultimate load carrying capacity, mid-span deflection, strain in concrete and reinforcement (steel and GFRP) of the beams have been reported. It is found that the effect of using fibers and higher grade of concrete is more pronounced in improving stiffness of GFRP RC beams compared to steel RC beams. Hence it can be concluded that GFRP rebars can be used as an efficient type of reinforcement in RC beams.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

In this paper, a novel microwave catalyst Ni@SiC/CNFs (NSC), C/Ni (NC), and C/SiC (SC) were successfully synthesized by electrostatic spinning method, and proved to degrade methylene blue with high efficiency under microwave irradiation. The results imply that the catalyst Ni@SiC/CNFs with double shell structure gave a 99.99 % removal rate in 90 s for the degradation of methylene blue under microwave irradiation, outperformed the C/Ni and C/SiC and most other reported catalysts in similar studies. On the one hand, the possible mechanism of the methylene blue degradation should be ascribed to that double shell structure increases the polarization source of the material, resulting in excellent microwave absorption properties; and on the other, the in-situ generation of active species OH• and O2 - under microwave radiation and the synergistic coupling effect of metal plasma greatly improved the degradation efficiency of methylene blue. The findings of this study could provide a valuable reference for the green degradation of industrial dye wastewater and its sustainable development process.

There are various approaches to managing polyethylene terephthalate waste, including methods for recycling PET. However, at present, only the cleanest wastes that can already be efficiently recycled using known methods are considered in the scientific literature. The study aims to look at other forms of polyethylene terephthalate waste that pose a challenge: low quality PET flakes, polyester tire cord, PET dust and prepolymer waste. The waste was characterized by FTIR spectroscopy, viscosimetry, differential scanning calorimetry, laser diffraction and sieve analysis. The findings describe the composition and properties of various forms of polyethylene terephthalate waste. Low quality PET flake waste and polyethylene terephthalate dust have been shown to be suitable for all chemical recycling methods. When recycling waste polyester tire cord, it is difficult to completely separate the rubber, so its presence in the final product must be taken into account. The most promising way to process a prepolymer is its depolymerization by hydrolysis, alcoholysis or glycolysis to produce monomers for the synthesis of PET, similar in properties to the primary one.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

Abstract: Although the pathophysiology of fibromyalgia syndrome has been better understood in recent decades, a unified model of its pathogenesis and an effective therapeutic approach are still far from being realized. The main aim of this article will be to delve into the fundamental mechanisms of the pathophysiology of fibromyalgia conceptualized as stress intolerance syndrome. Using the biopsychosocial model of chronic pain syndromes, we will describe the potential role of the attachment system, C tactile fibers, and oxytocinergic system dysfunction in the pathophysiology of fibromyalgia syndrome and other central sensitivity syndromes. At the end of the article, the therapeutic implications of this new global and translational pathophysiological model will be briefly discussed.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

This study aims to investigate the effects of cement kiln dust (CKD) on the hydration reactions and mechanical properties of cement and to evaluate its potential for use as a supplementary cementitious material (SCM). The key variables are the CKD type and incorporation rate. Cement paste and mortar specimens containing CKD were prepared to examine their effects on the cement hydration and mechanical properties. The impact on hydration was assessed using setting time measurements, heat of hydration tests, and thermogravimetric analysis (TG). In addition, compressive strength tests were conducted to evaluate the effect of CKD on the mechanical properties of the cement. The results indicated that CKD promoted early cement hydration and enhanced the early age mechanical properties. However, owing to its lack of pozzolanic reactivity, it did not significantly affect long-term hydration. Given that the effects of CKD vary slightly depending on its chemical composition, careful consideration of CKD's properties suggests that its potential use as a SCM is promising.

Recycling upholstery textiles is challenging due to the complexity of materials, which often include a mix of fabrics, foams, and adhesives that are difficult to separate. The intricate designs and layers in upholstered furniture make it labor-intensive and costly to dismantle for recycling. Additionally, contaminants like stains, finishes, and flame retardants complicate recycling. Despite these difficulties, recycling upholstery textiles is crucial to reducing landfill waste and conserving resources by reusing valuable materials. It also helps mitigate environmental pollution and carbon emissions associated with producing new textiles from virgin resources. The presented research aimed to establish the feasibility of incorporating textile fibers from waste artificial leather fibers from the upholstery furniture industry into the structure of high-density fiberboards. This approach positively contributes to carbon capture and storage (CCS) policy and mitigates the problem of such waste being sent to landfills. The research shows that while selected mechanical and physical parameters of the panels decrease with a rising content of recycled textile fibers, it is possible to meet proper European standard requirements by adjusting technological parameters such as nominal density.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Variable-Angle Tow (VAT) laminates can improve straight fiber composites mechanical properties thanks to the application of curvilinear fibers. This characteristic allows to achieve ambitious objectives for design and performance purposes. Nevertheless, the wider design space and the higher number of parameters result in a more complex structural problem. Among the various approaches that have been used for VATs study, Carrera’s Unified Formulation (CUF) allows to obtain multiple theories within the same framework, guaranteeing a good compromise between the results accuracy and the computational cost. In this article, the linear buckling behavior of VAT laminates is analyzed through the extension of CUF 2D plate models within the Reissner’s Mixed Variational Theorem (RMVT). Results show that RMVT can better approximate the prebuckling non-uniform stress field of the plate when compared to standard approaches, thus improving the prediction of the linear buckling loads of VAT composites.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

Soft pneumatic actuators/robotics have received significant interest in the medical and health fields, due to their intrinsic elasticity and simple control strategies enabling desired interaction. However, current soft hand pneumatic exoskeletons often exhibit uniform deformation, mismatch the profile of the interacted objects, and seldom quantify the assistive effects during activities of daily life (ADL), such as extension angle and joint stiffness predicted. The lack of quantification poses challenges to the effective and sustainable advancement of rehabilitation technology. This paper introduces the design, modeling, and testing of pneumatic bioinspired Segmented Composite Proprioceptive Bending Actuators (SCPBAs) for hand rehabilitation in ADL tasks. The actuator’s soft-joint/rigid-bone segmented structure, inspired by the human finger anatomy, provides a superior fit compared to traditional continuous structures. A quasi-static model is established to predict the bending angles based on geometrical parameters. The SCPBAs also include a quantitative evaluation of joint stiffness and extension angle utilizing proprioceptive bending information. Additionally, a soft under-actuated hand exoskeleton equipped with SCPBAs demonstrates its potential in ADL rehabilitation scenarios.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

This study aims to investigate the effect of banana stem fibers (BSFs) treatment with liquid smoke on changes in the micro-mechanics properties of BSFs, the tensile strength of single fibers, mor-phology, crystalline properties, and functional groups. The research used four model specimen variations, namely fiber without treatment and immersion in liquid smoke for 1, 2, and 3 hours. The BSFs with treatment was dried in an oven with a temperature of 40ºC for 30 minutes. Several tests were conducted, including a tensile test of single fiber capacity of 50N standard ASTM 3379-02, SEM observation, XRD, and FTIR test. The results showed that the highest increase in fiber strength was P2J, which was 264.21 MPa, and the lowest was TP fiber at 148.54 MPa. Fibers treatment with liquid smoke can form strong C-C elemental bonds caused by the H2O degradation process in BSFs, hence carbon atoms (C) are dense, and in conditions of excessive H2O degradation, the fiber strength will become brittle and the liquid smoke can increase the tensile strength of the fiber. The morphology of the fiber changed where the untreated fiber was covered with lignin, while the treated fiber had an elongated rectangular line pattern, porous, and the lignin was eroded. Crystalline properties in the X-ray diffractogram pattern differ between untreated and treated fibers. At an angle of 2ϴ, the lowest diffraction peak is around 160 in untreated wool, and the highest is 230 in treated fiber. The functional group of the fiber has changed where there is a difference in the wave crest between untreated and treatment fiber. The longer immersion time, the element of Carbon (C) will increase. In conclusion, treating BSFs with liquid smoke can change the physical, mechanical, and chemical properties, hence becoming a choice of composite reinforcement material in the future which is lightweight and environmentally friendly.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

The concept of intelligence has many applications, such as coatings and cyber security. Smart coatings have the ability to sense and/or response to external stimuli and generally interact with their environment. Self-healing coatings represent a significant advance in improving material durability and performance using microcapsules and nanocontainers loaded with self-healing agents, catalysts, corrosion inhibitors, and water-repellents. These smart coatings can repair damage on their own and restore mechanical properties without external intervention and are inspired by biological systems. Properties that are affected by either momentary or continuous external stimuli in smart coatings can be related to corrosion, fouling, fungal, self-healing, pie-zoelectric, microbiological, etc. These coating properties can be obtained via combinations of either organic or inorganic polymer phases, additives and pigments. In this article, a review on the advancements of micro/nanocapsules for self-healing coatings is reported from the aspect of ex-trinsic self-healing ability. The concept of extrinsic self-healing coatings is based on the use of capsules or multichannel vascular systems loaded with healing agents/inhibitors. The outcome is that self-healing coatings exhibit improved properties compared to traditional coatings. It is mentioned that self-healing anticorrosive coating not only has enhanced passive barrier function, but also realizes active defense. As a result, there is a significant improvement of the service life and overall performance of the coating. Future research should be devoted to refining self-healing mechanisms and developing cost-effective solutions for a wide range of industrial applications.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

Chemical modification of cellulose offers routes for structurally and functionally diverse biopolymer derivatives for numerous industrial applications. Among cellulose derivatives, cellulose ethers have found extensive use, such as emulsifiers, in food industries and biotechnology. Methylcellulose, one of the simplest cellulose derivatives, has been utilized for biomedical, construction materials and cell culture applications. Its improved water solubility, thermoresponsive gelation, and the ability to act as a matrix for various dopants also offer routes for cellulose-based functional materials. There has been a renewed interest in understanding the structural, mechanical, and optical properties of methylcellulose and its composites. This review focuses on the recent development in optically and mechanically tunable hydrogels derived from methylcellulose and methylcellulose-cellulose nanocrystal composites. We further discuss the application of the gels for preparing highly ductile and strong fibers. Finally, the emerging application of methylcellulose-based fibers as optical fibers and their application potentials are discussed.

The aim in this paper is the presentation of the influence of modification of polypropylene (PP) fibres on sorption capabilities of fibres. Modification of PP fibres were made with inorganic additives in the mass with a view to improving silicate composites – in construction. The prepared modified PP fibres were compared with pure PP fibres and their mechanical and thermomechanical properties were evaluated. And we wanted to evaluate and compare the sorption capabilities of these fibres using the Washburn method. However, the obtained results led us to the conclusion that the given method rather points to the excellent transport properties of PP fibres, as if it evaluated the sorption of the fibres.

With the development of the volume of information exchange and perception increases, the demands for intelligent, miniaturized and integrated optical devices for information acquisition are also increasing. As the core component of optical networks for transmitting information, how to further optimize its structural characteristics to generate richer optical characteristics and apply them to information exchange and optical field control has become a key research hotspot. The introduction of chiral twist characteristics has led to new phenomena and applications in optical field transmission and transformation for traditional optical fibers or microstructured optical fibers (MOF). Therefore, this review mainly starts from the principle of chiral optical fibers, introduces their preparation and latest application scenarios, and finally looks forward to their potential future development prospects.

We provide a very general review of the resonant transmission line method for optical fiber problems. The method has been found to work seamlessly for a variety of difficult problems including elliptical and eccentric core fibers as well as “holey”, photonic crystal fibers. A latest version has been shown to offer great versatility with respect to cases of unconventional, inhomogeneous index profiles.

The reinforcing effect of boehmite nanoparticles (BNP) in epoxy resins for fiber composite lightweight construction is related to the formation of a soft but bound interphase between filler and polymer. The interphase is able to dissipate crack propagation energy and consequently increases the fracture toughness of the epoxy resin. Usually, the nanoparticles are dispersed in the resin and then mixed with the hardener to form an applicable mixture to impregnate the fibers. If one wishes to locally increase the fracture toughness at particularly stressed positions of the fiber-reinforced polymer composites (FRPC), this could be done by spraying nanoparticles from a suspension. However, this would entail high costs for removing the nanoparticles from the ambient air. We propose that a fiber fleece containing bound nanoparticles be inserted at exposed locations. For the present proof-of-concept study, an electrospun polycarbonate nonwoven and taurine modified BNP are proposed. After fabrication of suitable PC/EP/BNP composites, the thermomechanical properties were tested by dynamic mechanical analysis (DMTA). Comparatively, the local nano-mechanical properties such as stiffness and elastic modulus were determined by atomic force microscopy (AFM). An additional investigation of the distribution of the nanoparticles in the epoxy matrix, which is a prerequisite for an effective nanocomposite, is carried out by scanning electron microscopy in transmission mode (TSEM). From the results it can be concluded that the concept of carrier fibers for nanoparticles is viable.

Purpose: The purpose of this study is to apply the Composite Radiographic Index modified (CRIm) in CBCT scans of patients with Medication related osteonecrosis of the jaws (MRONJ) in order to detect its validity, and corelate the radiologic findings with the clinical staging of the disease. Methods: This study included 43 patients with MRONJ diagnosis and CBCT scans performed in the School of Dentistry and approved by the Research Ethics Committee. Clinical staging for every patient (0-3) was provided according to AAOMS 2022 guidelines. In cases of patients with both jaws affected, each jaw was evaluated independently resulting to 52 CBCT scans. The 52 CBCT scans were assessed under standardized viewing conditions by 2 observers who evaluated independently the following 8 radiologic features: lytic changes, sclerosis, periosteal reaction, sequestration, non-healing extraction sockets and other findings (sinus implication, inferior alveolar canal involvement, jaw fracture). The CRIm index was constructed to assess the extent of osseous changes. The radiologic features were scored as absent (0), localized/single (1), extensive/multiple (2), yielding a theoretical range of 0–12. For statistical analysis Fisher’s exact test and Spearman’s correlation coefficient were performed. Results: A statistically significant association of clinical stage with lytic changes, sequestration and inferior alveolar canal involvement was found. Also, a statistically significant correlation of clinical stage with CRIm index classification was obtained. Conclusions: The CRIm index tends to increase as the clinical stages of MRONJ advance, suggesting a correlation between the clinical stage of MRONJ and the CRIm index.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

Recycled tire fibers (RTF) are currently one of the most abundant waste not being recovered due to several processing hurdles and the presence of high amounts of residual ground rubber particles (GR). Therefore, this study proposes a simple approach to separate most of rubber particles from fibers and to determine their rubber content using thermogravimetric analysis (TGA)/calcination. Afterwards, clean fiber (CF) and GR are used as fillers for recycled post-consumer low density polyethylene (rLDPE), and their effects on the physical properties are investigated. Accordingly, a series of composites with CF and GR is prepared at different filler concentrations (0-30%) via extrusion compounding before using compression molding and injection molding for comparison. In all cases, injection molding leads to higher strength and modulus, but lower elongation at break. The results show that incorporating 30 wt.% of CF into rLDPE yields a remarkable improvement in tensile strength (15%), tensile modulus (192%) and flexural modulus (142%). On the other hand, the incorporation of up to 30 wt.% of GR results in a reduction of both tensile strength and flexural modulus by 15%, confirming the critical role of the cleaning process for RTF in achieving the best results.

Electrospinning is a simple versatile method to generate nanofibres. Remarkable progress has been made in the development of electrospinning process. The production of nanofibers is affected by many parameters, which influence the final material properties. Electrospun fibers have a wide range of applications such as energy storage and biomedical scaffolds. Polyacrylonitrile (PAN) has been widely used in the production of carbon nanofibers. PAN has received increasing interest in recent years, due to its excellent characteristics, such as spinnability, biocompatibility, and commercial viability, opening new applications in the biotechnological field. This paper provides an overview of the electrospinning process, its main parameters, and operation modes that affect nanofibers fabrication. A review of their biological applications is proposed. A focus is made on PAN fibers formation, functionalization, and application as scaffolds to allow cell growth. Overall, nanofibre scaffolds, made of stabilized PAN, appear as a powerful tool in medical applications needing controlled cell culture.

The present study investigates the failure mechanisms of industrial fiber materials, using a custom designed fiber cutting performance test bench. The fracture morphologies of single PA6 fibers are examined by scanning electron microscopy. The analysis reveals that fiber cutting can be distinguished according to four distinct stages of fiber failure represented by shearing, cutting, brittle fracture, and tensile failure, which are the result of different mechanisms active during the processes of crack initiation, extension and fracture. The results of fractographic analysis are further verified by an analysis of the blade assembly speed with respect to time over the entire fracture failure process based on high-speed camera data. The results of fractographic analysis and blade assembly speed are fully consistent.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

The açaí (Euterpe oleracea Mart.) is a native fruit of the Amazon that is well-known due to its commercial value. Its production chain is centered in the state of Pará, largely supplied by extractivism. The processing of açaí fruits in nature generates huge amount of solid waste, which can pose serious risks to the environment if not used and managed properly. Due to a small number of systhematic studies on the effect of chemical activation by pyrolysis of açaí seeds and fibers, and with the aim of providing a basis for future applications of the waste generated by processing of açaí fruits, the present work proposes a study of the pyrolysis of açaí seeds and fibers and the physicochemical and compositional characterization of the aqueous phase products. In this way, açaí seeds were collected from a local artisan processing facility in the city of Belém, PA. The seeds were dried at 105°C until constant weight, and subsequently, the fibers were separated from the seeds in a rotating drum. The seeds and fibers were impregnated with NaOH solutions at 0.5M, 1.0M, and 2.0M, and then pyrolyzed at a laboratory scale at 450 °C and 1 atm. The liquid products from pyrolysis were characterized through acidity index analysis, Fourier-transform infrared spectroscopy, and gas chromatography. The increase in the concentration of the impregnating agent resulted in an increase in bio-oil yield from both the seeds and fibers, rising from 3.3% (raw seeds) to 6.6% (seeds impregnated with 2M NaOH) and from 1.2% (raw fibers) to 3.7% (fibers impregnated with 2M NaOH). The yield in the aqueous phase after biomass pyrolysis showed an inverse behavior to the bio-oil yield, decreasing from 33.7% (raw fibers) to 21.2% (fibers impregnated with 2M NaOH) and from 41% (raw seeds) to 37.5% (seeds impregnated with 2.0M NaOH). High acidity levels were found in the aqueous phase samples and bio-oils derived from the seeds and fibers, which decreased as the concentration of the impregnating agent increased. The increase in the concentration of the impregnating agent (NaOH) influenced the chemical composition of the obtained liquid products, leading to a decrease in oxygenated compounds and an increase in nitrogenous compounds in both experimental matrices, which was also evidenced by the reduction in acidity.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a Ultra-high performance concrete (UHPC) has gained worldwide popularity because of its notable mechanical response. This research studied the compressive strength, modulus of elasticity, and flexural tensile strength of UHPC. Batches were made with the addition of steel and PVA fibers using a standard procedure defined in the research. The experimental data from the compressive strength test was analyzed in the Statistica 10 software to investigate the fibers' influence on UHPC's mechanical properties. An analysis of the elastic modulus prediction was carried out according to international standards. It was found that the normalized equations for the elastic modulus are not adequate for its estimation. The statistical analysis indicated that the range of fiber quantities analyzed did not significantly affect the compressive strength and the elastic modulus. Regarding the optimized mix, its flexural tensile strength indicates that the fiber content must be higher for UHPC to be suitable for structural use.

In the past decades, Fiber Reinforced Concrete has been gaining more attention in the concrete research development. There are many advantages of the inclusion of fiber into reinforced concrete structures. It was found that the inclusion of fibers in concrete, be it synthetic or natural, resulted in the improvement of the thermal properties of concrete, as well as its strength to some extent. However, the inclusion of fibers in concrete does affects its thermo-mechanical properties. The objective of this study is to identify the potential of the addition Polypropylene and Kenaf fibers in cement mortar at different compositions (0.1%, 0.2%, and 0.3%). Eight mixes were analyzed for this purpose. Upon investigating the flow ability, compressive strength, tensile strength, and thermal conductivity of the mortar samples, it was found that the incorporation of PP and Kenaf fibers reduced the flow ability. Cement mortar samples containing 0.1% addition of PP and Kenaf fibers show the highest compressive strength compared to other percentages, while samples containing 0.3% addition of PP and Kenaf fibers show the highest tensile strength compared to other percentages. The thermal conductivity of mortar samples shows reduction when high percentages of both fibers were used.

This study addresses the enhancement of material efficiency and reduction of brittleness in timber-to-concrete adhesive connections for beam-type timber and timber-concrete composite panels. The research explores the potential benefits of adding longitudinal timber ribs to Cross-Laminated Timber (CLT) beam-type panels. Three groups of flexure-tested specimens were analysed: (1) timber panels (1400 mm × 400 mm) with two 100 mm thick CLT panels and two 60 mm thick CLT panels reinforced with 150x80 mm timber ribs; (2) eight specimens (600 mm × 100 mm × 150 mm) with CLT members (600 mm × 100 mm × 100 mm) connected to a 50 mm concrete layer using granite chips and Sikadur-31 (AB) epoxy adhesive; (3) six CLT panels (1400 mm × 400 mm × 50 mm) bonded to a 50 mm concrete layer, with two panels containing polypropylene microfibers and two panels incorporating polyethene dowels for mechanical connection. Specimens were subjected to three-point bending tests and analysed using the transformed section method, γ-method, and finite element method with ANSYS 2023R2 software. Results indicated a 53% increase in load-carrying capacity for ribbed CLT panels with no additional material consumption, a 24.8%-41.1% increase for CLT panels strengthened with a concrete layer, and improved ductility and prevention of disintegration in timber-concrete composites with polypropylene microfibers.

A frequent problem in Geotechnics is the soils with inadequate physical-mechanical properties before the efforts to which they will be subjected by the constructions, incurring cost overruns caused by their engineering improvement. The need to improve the engineering properties of soils is not recent, currently observing that the most common alternatives are binders such as cement and lime. The climate change observed in recent decades and the uncontrolled emission of greenhouse gases have motivated Geotechnical and Geoenvironmental researchers to seek mechanisms for soil reinforcement from a more sustainable and environmentally friendly approach by proposing the use of recycled and waste materials. An alternative is natural fibers, which can be obtained as waste from many agro-industrial processes, implying their high availability and low cost. Sawdust as a by-product of wood processing has a rough texture that can generate high friction between the fiber and the matrix of the soils, leading to a significant increase in its shearing strength and bearing capacity. This concept of improving the properties of soils using natural fibers distributed randomly is inspired by the natural phenomenon of grass and/or plants that when growing on a slope can effectively stabilize a said slope.

Nowadays, in order to improve asphalt pavement performance, durability and reduce environmental pollution caused by asphalt binder, many researchers are studying to modify asphalt concrete (AC) and find alternative paving materials to extend service life of asphalt pavement. One of the successful materials used in a modification of AC are fibers. Different types of fibers have been reinforced in AC mixture and improvements have been observed. This research studies the performance of glass wool fiber reinforced in a dense-graded asphalt mixture. Generally, glass fibers are known to have excellent mechanical properties such as high tensile modulus, 100% elastic recovery and a very high tolerance to heat. The glass wool fibers are commonly used as a thermal insulation material. In this research to evaluate the performance of glass wool fiber in AC, laboratory tests Marshall mix design test, Indirect tensile strength (IDT), Tensile strength ratio (TSR) and Kim test were conducted to determine a proper mix design, tensile properties, moisture susceptibility, rutting and fatigue behaviors. Results show that addition of glass wool fibers does affect the properties of AC mixture. The use of glass wool fibers showed a positive consistence results, in which it improved the moisture susceptibility and rutting resistance of the AC. Also result showed addition of fiber increased tensile strength and toughness which indicates that fibers have a potential to resist distresses that occur on a surface of the road as a result of heavy traffic loading. The overall results showed that addition of glass wool fiber in AC mixture is beneficial in improving properties of AC pavements.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

This study presents, for the first time, the development of fibers with favorable properties for biodegradable wound dressings made from the Ecovio® (EC) polymer blend, composed of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT), incorporated with tea tree essential oil (TTE). TTE presented antimicrobial activity against Pseudomonas aeruginosa and Staphylococcus aureus, achieving minimal inhibitory concentrations of 15 and 7.5 mg/mL, respectively. The TTE was mixed with EC in a binary chloroform and formic acid (85/15 v/v) mixture, leading to homogeneous and wettable fibers by electrospinning. The EC/TTE fibers were characterized confirming the TTE in the fibers. The tests showed that TTE (0.5, 1.0 or 1.5 mL) improved the polymer blend electrospinnability. TTE (1.5 mL or 75 w% concerning the EC) lead to homogeneous fibers with an average diameter of 278 nm. TTE (75 w%) increased the wettability of the EC fibers from 120±2° to 69±1°. Preliminary bacterial adhesion and proliferation assays demonstrated that the EC/TTE fibers have anti-adhesive activity e seems to be more toxic against P. aeruginosa compared to S. aureus after 24 hours of incubation. Compatibility tests with human blood indicated that the EC/TTE fibers accelerate blood coagulation. The EC/TTE fibers exhibit promising chemical and biological properties (in vitro) for the development of wound dressings.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

Exploring for green and affordable protection of perishable fruit like cherry tomato is of significance. Here the protective efficacy and its underpinnings of coating with oleaster gum, alone or incorporated with cuminal, on cherry tomatoes stored at ambient temperature were investigated. The composite coating of oleaster gum with 0.1% cuminal reduced decay, respiration rate, weight loss, and softening of the fruit and decelerated their decreases of total soluble solids, titratable acidity, and soluble proteins, and therefore maintained their marketability. Furthermore, it reduced the accumulation of O•− 2and H2O2 in fruit, and mitigated cell membrane lipid oxidation and permeabilization, thereby retarding their senescence. Instrumentally, it elevated the activities of superoxide dismutase, catalase, peroxidase, and ascorbate peroxidase and the levels of ascorbic acid and glutathione. This potentiation of the fruit antioxidant system makes the composite coating a promising approach to keeping the postharvest quality of perishable fruit.

Single-fluid electrospinning creates nanofibers from molten polymer solutions with active ingredients. The study utilized a combination of a fractional factorial design and a Box-Behnken design to examine crucial factors among a multitude of parameters and to optimize the electrospinning conditions that impact the fiber mats' morphology and entrapment efficiency of the Senna alata leaf extract. The findings indicated that the shellac content had the greatest impact on both fiber diameter and bead formation. The optimum electrospinning conditions were identified as a voltage of 24 kV, a solution feed rate of 0.8 mL/h, and a shellac-extract ratio of 38.5:3.8. These conditions produced nanosized fibers with a diameter of 306 nm, a low bead-to-fiber ratio of 0.29, and an extract entrapment efficiency of 96% within the fibers. The biphasic profile of optimized nanofibers was confirmed through an in vitro release study. This profile consisted of an initial burst release of 88% within the first hour, which was succeeded by a sustained release pattern surpassing 90% for the next 12 h, as predicted by zero-order release kinetics. The optimized nanofibers demonstrated antimicrobial efficacy against diverse pathogens, suggesting promising applications in wound dressings and protective textiles.

This work seeks to approach the comparative analysis of the distribution of POFs (polymeric optical fibers) arranged in a random and sorted manner in the manufacture of translucent concretes. The following characteristics were analyzed: compressive strength, flexural tensile strength, capillary water absorption and light transmittance. Portland cement, water, fine aggregate (sand), silica fume, polycarboxylate ether-based superplasticizer and polymeric optical fiber were used in the production of the composites. Except the fiber content, the mixture of all other inputs was kept as a fixed parameter. Groups with the following levels of POFs were produced: 0%, 2%, 3.5% and 5%. The POF content is the sum of the areas of the fiber sections in the composite with the total area of the translucent surface. The results showed that for the analysis of mechanical behavior (flexural tensile and compressive strength) and durability (capillary water absorption), composites with random and sorted fibers within the 2% POF presented to belong to statistically distinct groups. For the other fiber contents, there was no pattern of behavior, that is, it cannot be said that there is a difference within 3.5% or 5% POF between sorted and random fibers in relation to the mechanical and durability characteristics analyzed. As for the light transmittance, it was attributed that the statistical difference between the fiber arrangements only within the 5% POF content can be a consequence of their accumulation in certain points of the material, thus influencing this characteristic measured by a light meter.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

A total internal reflection photonic crystal fiber (PCF) based on hexagonal core is proposed for gas sensing in a specific wavelength range. The higher sensitivity and lower confinement loss were realized by the structure of the proposed PCF consists of two layers with circular holes rotated hexagonally around a core region and six slotted air-hole in the cladding based on numerical analysis. The simulation results show that the enhancement of the relative sensitivity has been done by enhancing the diameter of the hexagonal shape air-hole cladding (d1) and the hexagonal arranged holes around the central solid core (d0) in this design. Also, the confinement loss has been reduced by enhancing the ratio of length to width of slotted holes (l/w) and decreasing the cladding air-hole diameters (d1). As the refractive index increases, the wavelength shifts toward the long wavelength. And in a certain temperature range, the transmission characteristics of the device does not change with the temperature. The results are helpful for designing high performance PCF for gas sensing applications.

In this study, fibers were extracted from different parts of the okra plant (Abelmoschus esculentus) via water- and dew-retting methods. The fibers were subjected to physical and thermal analyses. The fibers obtained from the upper part of the okra plant show higher breaking strength and lower linear density. Fibers obtained via water-retting exhibited higher breaking strength, elongation at break rates, and lower linear density values. The paper also presents the results of thermogravimetric analysis of the okra fibers. Tests were carried out in oxygen and inert gas atmospheres. The temperature range of the main thermal decomposition stage was in the 275–400°C for range thermo-oxidation and 300–425°C for pyrolysis investigation. Slight differences were found in the thermal resistances of the tested fibers, which was confirmed by an analysis using the alpha s- alpha r methodology. The calculated activation energy values show a large-spread range.

In recent years, tremendous progress has been made in the development of rare-earth ion doped tellurite glass laser sources, ranging from watt and multiwatt level fiber lasers to nanowatt level microsphere lasers. Significant success has been achieved in extending the spectral range of tellurite fiber lasers generating at wavelengths beyond 2 μm as well as in theoretical understanding. This review is aimed at discussing the state of the art of neodymium-, erbium-, thulium-, and holmium-doped tellurite glass fiber and microsphere lasers.

Fiber reinforced polymer (FRP) is one of the important material used for strengthening and retrofitting of reinforced concrete structures. The commonly used fibers are glass, carbon and aramid fibers. Durability of structures can be extended by selecting appropriate method of strengthening. FRP wrapping is one of the easiest methods for repair, retrofit and maintenance of structural element. Deterioration of structures may be due to moisture content, salt water, or contact with alkali solutions. There is significant effect of permeability, rise in temperature, chemical attack, fatigue action, micro pores on members of structures. Using FRP additional strength can be gained by structural elements. This paper investigates durability of aramid fiber subjected to acid attack and temperature rise. Concrete cubes are prepared as specimens with double wrapping of aramid fibers. Diluted hydrochloric acid solution is used for immersion of specimen for curing period of 7, 30 and 70 days. In case of fire resistance test, such specimens are kept in hot air oven at a temperature of 2000C at different time intervals. The effect of aramid fiber wrapping on compressive strength and weight loss of specimen is studied.

The use of natural fibres is investigated in recent years in cement, lime or geopolymer mortars to increase their toughness, resistance, tensile strength and durability. These fibres, derived from sources such as jute, hemp, sisal, and flax, are added to the mortar mix to enhance its mechanical properties and reduce cracking. The choice of the natural source strongly depends on local availability of the plant, its use and harvesting. In this paper the fibres of Diss (Ampelodesmos Mauritanicus, Poir) were used as reinforcement for mortars prepared by using waste materials, such as waste glass powder and air hardening lime obtained by the kilning of marble slurry. The samples underwent artificial and natural ageing and were characterized by measuring apparent density, water sorption coefficient, compression and bending stress, indicating a positive role of fibres addiction in increasing mortars durability.

Forensic assessments may involve the sampling of textile fibers when examining crime scenes. The need to characterize and identify those fibers is crucial as they can provide extensive information relating to a crime, linking a suspect to a location. Fibers in particular may contain issues in terms of both size and quantity of sample, and micro Fourier transform Infrared in attenuated total reflectance mode (micro FTIR-ATR) spectroscopy presents a non-destructive method to identify those fibers. In this study we carried out a rapid forensic assessment via micro FTIR-ATR of sixty textile fibers recovered from twenty white fabrics relying on tape lifting method, in order to discriminate those materials. Two dimensional principal component analysis and radar chart were applied to enhance the visual comparison of the fibers. Results of infrared spectra revealed that the technique allows the discrimination of textile fibers according to their spectral composition (cellulose, polyamide, polyester, or mixture of these composites) and to some characteristics, as number and width of peaks, peak position according to the wavenumber, absorbance index related to peak sharpness, etc. The technique was deemed useful in the forensic assessment of the fibers, presenting rapid and enlightening results.

We study impact of geometry on leakage loss in negative curvature fibers made with As₂Se₃ chalcogenide and As₂Se₃ chalcogenide glasses for carbon dioxide (CO₂) laser transmission. The minimum leakage loss decreases when the core diameter increases both for fibers with six and for fibers with eight cladding tubes. The optimum gap corresponding to the minimum loss increases when the core diameter increases for negative curvature fibers with six cladding tubes. For negative curvature fibers with eight cladding tubes, the optimum gap is always less than 20 μm when the core diameter ranges from 300 μm to 500 μm. The influence of material loss on fiber loss is also studied. When material loss exceeds 10² dB/m, it dominates the fiber leakage loss for negative curvature fiber at a wavelength of 10.6 μm.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

The interfacial interface between the fibers and the matrix plays a key role for epoxy matrix composites and short recycled randomly arranged fibres. This study used short recycled carbon fiber (RCF) as a filler. Plasma treatment was used for carbon fiber surface treatment. This treat-ment was performed using radio (RF) and microwave (MW) frequencies at the same pressure and atmosphere. Appropriate chemical modification of the fiber surfaces helps to improve the wettability of the carbon fibers and, at the same time, allows the necessary covalent bonds to form between the fibers and the epoxy matrix. The effect of the plasma treatment was analyzed and confirmed by XPS analysis, Raman microscopy, SEM, TEM and wettability measurements. Composite samples filled with recycled carbon fibers with low concentrations (1 wt%, 2.5 wt% and 5 wt%) and high concentrations (20 wt% and 30 wt%) were made from selected treated fi-bers. The mechanical properties (impact toughness, 3PB) were analyzed on these samples. It was found that the modulus of elasticity and bending stress increase with the increasing content of recycled carbon fibers. A more significant change in impact strength occurred in samples with low concentration.

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Self-healing, stretchable and moldable hydrogels have a great potential application in tissue engineering and soft robotics. Despite great success in reported hydrogels, it is still a great challenge to construct the moldable hydrogels with an ultrafast self-healing performance. Herein, the dynamic double network (DN) composite hydrogels (PBLH) with ultrafast self-healing, stretchable and moldable were successfully constructed by poly (vinyl alcohol) (PVA), borate, ε-poly-L-lysine (EPL) and hyaluronic acid (HA) based on an efficient one-pot method. Fourier transform infrared spectroscopy, X-Ray diffraction and rheological measurements confirmed the formation of dynamic double networks among PVA, B, EPL and HA through the cross-linking of dynamic borate bonds, electrostatic interaction and hydrogen bonding. Having fabricated the dynamic double network structure, the damage gap of the composite hydrogels can heal within 1 min, presenting an excellent self-healing ability. Simultaneously, the DN hydrogels can be molded to various shapes and the length of the DN hydrogels can be stretched to 15 times than original length. In addition, the DN hydrogels exhibited an excellent antibacterial property against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). Our results illustrated that the DN composite hydrogels not only retain the advantages of traditional hydrogels, but also possess ultrafast self-healing, outstanding stretchable and antibacterial properties, presenting a prospective candidate for constructing biomedical materials.

In this paper, design of optical spectral filters based on mode coupling of optical fibers is presented. The finite difference method is applied to find the dispersion characteristics of optical fiber coupler constructing from two fibers as a composite multi-dielectric waveguide with different cores but the same cladding. Also, the field distribution for both fibers as a separate and as a composite waveguide. The spectral characteristics of the filters are investigated depending on the coupling of two linear polarized modes LP01 and LP11. The dependence of the transmission coefficient on operating wavelengths is illustrated. Finally, the spectral bandwidth of filter as a function of the distance between the two cores is addressed.

Products made from petroleum-derived plastic materials are linked to many environmental problems such as greenhouse gas emissions and plastic pollution. It is desirable to manufacture products from environmentally friendly materials instead of petroleum-based plastic materials. Products made from biomass-fungi composite materials are biodegradable and can be utilized for packaging, construction, and furniture. In biomass-fungi composite materials, biomass particles (derived from agricultural wastes) serve as the substrate and the fungal hyphae network binds the biomass particles together. There are many reported studies on 3D printing of biomass-fungi composite materials. However, there are no reported studies on biodegradation of 3D printed samples from biomass-fungi composite materials. In this study, two types of biomass materials were used to prepare printable mixture hemp hurd and beechwood sawdust. The fungi strain used was Trametes versicolor. Extrusion based 3D printing was used to print samples. 3D printed samples were left for five days to allow fungi to grow. The samples were then dried in an oven for 4 hours at 120ºC to kill all the fungi in the samples. The samples were buried in the soil using a mesh bag and kept in an environmental chamber at 25℃ with a relative humidity of 48%. The weight of these samples was measured every week over the period of three months. Both types of samples (prepared from beechwood sawdust and hemp hurd, respectively) showed weight change after three months. Furthermore, the samples made from hemp hurd had more weight change than the samples made from beechwood sawdust. The SEM (scanning electron microscope) micrographs and FTIR (Fourier transform infrared) spectroscopy showed evidence of biodegradation of these samples.

The identification and quantitative determination of wool and fine animal fibers are of great interest in the textile field because of significant price differences between them and common adulterations in raw and processed textiles. Since animal fibers have remarkable similarities in their chemical and physical characteristics, specific identification methods have been studied and proposed following advances in analytical technologies. The identification methods of wool and fine animal fibers are reviewed in this paper and the results of relevant studies are listed and summarized, starting from classical microscopy methods which are still used today not only in Small to Medium Enterprises but also in large industries, research studies and quality control laboratories. Particular attention has been paid to image analysis, Nir spectroscopy and proteomics which constitute the most promising technologies of quality control in the manufacturing and trading of luxury textiles and can find application in forensic science and archeology.

This study aimed to investigate Coll-I, III, IV and elastin in canine normal prostate and PC, using Picrosirius red (PSR) and Immunohistochemical (IHC) analysis. Eight normal prostates and 10 PC from formalin-fixed, paraffin-embedded samples were used. Collagen fibers area was analyzed with ImageJ software. The distribution of Coll-I and Coll-III was approximately 80% around prostatic ducts and acini, 15% among smooth muscle and 5% surrounding blood vessels, in both normal prostate and PC. There was a higher median area of Coll-III in PC, when compared to normal prostatic tissue (p=0.001 for PSR and p= 0.05 for IHC). Immunostaining for Coll-IV was observed in the basal membrane of prostate acini, smooth muscle, blood vessels, and nerve fibers of normal and PC samples. Although there was no difference in Coll-IV area between normal tissue and PC, tumors with Gleason score 10 showed absence of Coll-IV, when compared to scores 6 and 8 (p=0.0095). Elastic fibers were found in the septa dividing the lobules and around the prostatic acini of normal samples, and was statistically higher in PC, compared to normal tissue (p=0.00229). Investigation of ECM components brings new information and should be correlated with prognosis in future studies.

Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (<0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

Cocoa bean shells (CBSs) represent the external layer of cocoa beans. The shells are removed during the winnowing after the pre-roasting, a processing step of chocolate production; in in the past they were considered a waste. CBSs possess many interesting nutritional characteristics in both macro and micronutrients. CBSs result very rich in dietary fiber and antioxidant compounds such as phenolic acids and flavan-3-ols. Soluble dietary fibers are potentially associated with fermentability and prebiotic activity on human gut microbiota instead antioxidants compounds have been linked with positive effects on human health. Based on these properties, the aim of this study was the valorization of CBSs thorough enzymatic treatments. The shells were treated both raw and defatted; three sets of carbohydrases have been used in order to destructure the fiber profile, potentially enhancing the potential prebiotic activity of CBSs. Cellulase, xylanase and pectinase were used to perform enzymatic treatments. After the enzymatic hydrolisis, both soluble and insoluble fibers fraction were quantified, in parallel with the total phenolic and the total flavonoid contents and the antioxidant activity. Moreover, the HPLC-PDA analysis was carried out for the main compounds of CBSs. The enzymatic treatmens allowed to obtain an enhancement in soluble fibers, for both defatted and raw CBSs, particularly using cellulase, xylanase and their combinations. Finally, a parallel preservation of the antioxidant capacity and the content of the main bioactive compounds after the treatments was observed. These results can be used to exploit the enzymatic treated CBSs to further industrial applications in the food and nutraceutical fields.

The global textile sector, pivotal to economic development, significantly contributes to environmental degradation, prompting a shift towards sustainable raw material sources. Embracing circular economy principles, this industry is exploring the valorization of agricultural by-products. This study introduces an innovative approach to repurposing mango waste into valuable textile fibers, a byproduct of the fruit processing industry, predominantly generated during juice and jam production. The focus is on the lignocellulosic constituents of mango waste, specifically the peel, seed, and fibrous material, traditionally considered as refuse. Previous research has predominantly utilized mango peel in pectin extraction for food applications, whereas the potential of seed and fibrous content remains underexplored. This investigation endeavors to transform these fibrous by-products into high-value materials suitable for textile manufacturing. The process involved washing, drying, and comprehensive physicochemical characterization of mango fibers, emphasizing lignin quantification, revealing a composition of 12.2% lignin. An experimental design was employed to elucidate the impact of variables such as liquid-to-solid ratio, reaction duration, and sodium hydroxide concentration on lignin dissolution through alkaline hydrolysis. Optimal conditions—10% NaOH concentration, 30 mL/g liquid-to-solid ratio over six hours—achieved an 83% reduction in lignin content. The resulting fibers exhibited properties akin to conventional natural fibers, including a favorable aspect ratio indicative of their suitability for textile applications. A subsequent softening process using propylene glycol enhanced the fibers' spinability, producing a durable, textured fabric ideal for eco-conscious fashion applications, including bags, footwear, and accessories. This research demonstrates the feasibility of converting mango waste into a textile-worthy material and underscores the importance of waste revalorization in promoting sustainability within the circular economy framework.

The electrical, mechanical and thermal conductivity of ethylene butene copolymer (EBC) composites with carbon fibers were studied. EBC/carbon-fiber composites can be utilized as an electro-mechanical material which is capable of changing it electric resistance with mechanical strain. Carbon fibers were introduced to EBC with different concentrations (5-25 wt%). The results showed that the addition of carbon fibers to EBC could increase the electric resistance up to 10 times. Increasing the load to 2.9 MPa could increase the electric resistance change by 4500% compared 25% fiber sample with pure EBC. It is also noted that the electric resistance of the EBC/CF composites underwent a dramatic increase with raising the strain, for example, the resistance change was around 13 times more at 15% strain in comparison to 5% of strain; The thermal conductivity tests showed that the addition of carbon fibers could increase the thermal conductivity by 40%, from 0.19 to 0.27 (Wm-1K-1). It was also observed that the addition of carbon fibers to EBC could increase the thermal conductivity.

This paper presents the results of laboratory tests of CFRP (carbon fibre-reinforced polymer) laminates, which allowed the development of numerical material models. The obtained data were used in a further stage to perform numerical simulations of four variants of medical tabletops differing, among other features, in the shape of the cross-section. Maximum deflections and effort in the composite material were analyzed. The final step was to perform a laboratory test for one of the tabletop versions, the results of which confirmed the correctness of the numerical calculations. This work is aimed at both researchers and designers involved in the practical application of fibre-reinforced polymer matrix composites.

Herein, the mechanical properties and carbonation durability of engineered cementitious composites (ECC) were studied. For cost-efficient utilization of ECC materials, polypropylene (PP) and hydrophilic polyvinyl alcohol (PVA) fibers were employed to cast different types of specimens. The compressive strength, Poisson’s ratio, strength-deflection curves, cracking/post-cracking strength, impact index, and tensile strain-stress curves of the two types of ECC materials, with different fiber contents of 0 vol%, 1 vol%, 1.5 vol% and 2 vol%, were investigated by conducting compressive tests, four-point bending tests, drop weight tests, and uniaxial tensile tests. In addition, the matrix microstructure and failure morphology of the fiber in the ECC materials were studied by scanning electron microscopy (SEM) analysis. Furthermore, carbonation test and steel corrosion after carbonization were employed to study durability resistance. The results indicated that for both PP fiber- and hydrophilic PVA fiber-reinforced ECCs, the compressive strength first increases and then decreases as fiber content increases from 0 vol% to 2 vol% and reaches the maximum at 1 vol% fiber content. The bending strength, deformation capacity, and impact resistance show significant improvement with increasing fiber contents. The ECC material reinforced with 2 vol% PP fiber shows superior carbonized durability with maximum carbonation depth of only 0.8 mm.

Gelatin fibers have a specific surface and high porosity, which is why their use in medicine and the food industry is being researched. This article explores the potential of centrifugal spinning to produce gelatin fibers. Gelatin for fiber preparation is obtained from a non-traditional source of collagen (chicken by-products) using a unique enzymatic process. The fiber quality is compared with those prepared from traditional collagen tissues (porcine, bovine). The results show that fibers crosslinked with glutaraldehyde vapor preserve their structure even in contact with water. Using a cross-linker controls swelling ability and solubility while maintaining the fiber structure. On the contrary, uncross-linked gelatin fibers are water soluble due to a high surface-to-volume ratio, facilitating water penetration and dissolution. Scanning electron microscopy (SEM) provided a clearer picture of the morphology of gelatin fibers obtained by centrifugal spinning. Differences in the amount of bonding depending on the raw material used and the presence of cross-linker were analyzed using Fourier transform infrared spectroscopy (FTIR). The overall results showed that chicken gelatin is a suitable alternative to gelatins from traditional sources.

In this paper, we consider the behavior of the local energy flow velocity of the fundamental air – core mode at the core – cladding boundary in two types of hollow – core fibers: hollow – core fibers with a negative curvature of the core boundary and single – capillary fibers with similar geometrical parameters. It is demonstrated that the behavior of both axial and radial components of the local energy velocity of the fundamental air – core mode is completely different for these two types of hollow – core fibers. The negative curvature of the core boundary leads to an alternating behavior of the radial projection of the local energy velocity and a decrease by two orders of magnitude compared to the values of this projection for a single capillary. In our opinion, this behavior of the local energy velocity of the fundamental air – core mode is caused by a periodic set of Poynting vector vortices that appear in the cladding capillary walls.

Carbon concrete PAN/lignin-based CF composites are a new promising material class for the building industry. The replacement of the traditional heavy and corroding steel reinforcement by carbon fiber (CF) based reinforcements offers many significant advantages: a higher protection of environmental resources because of lower CO2 consumption during cement production, a longer lifecycle and thus muss less damage in structural components and a higher degree of design freedom because lightweight solutions can be realized. However, due to cost pressure in civil engineering, completely new process chains are required to manufacture CF based reinforcement structures for concrete. The article describes the necessary process steps in order to develop CF reinforcement: (1) the production of cost-effective CF using novel carbon fiber lines, (2) the fabrication of CF rebars with different geometry profiles. It was found that PAN/lignin-based CF is currently the most promising material in order to meet the future market demands. However, significant research needs to be undertaken in order to improve the properties of lignin-based and PAN/lignin-based CF, respectively. The CF can be manufactured to CF-based rebars using different manufacturing technologies which have been developed on prototype level in this study.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Nickel electrodeposition is a widely utilized method for creating thin films on various substrates with various desirable attributes. Recently, there has been a growing interest in developing nickel composite coatings that incorporate additional elements or particles into the nickel matrix to enhance their properties. These composite coatings offer superior wear resistance, corrosion resistance, hardness, and other functional benefits compared to pure nickel coatings. Some of the recent advancements in electrodeposited nickel composite coatings include improved wear resistance, enhanced mechanical properties and better corrosion resistance. Researchers have discovered that adding Al, Si, Zr, C, W, and Ti particles to nickel coatings can significantly enhance wear resistance. The uniform distribution of these particles within the nickel matrix acts as a barrier to wear and tear. Studies have also shown that nickel composite coatings with Al, Si, Zr, C, W, and Ti particles exhibit superior mechanical properties, including increased hardness. These particles refine the grain size of the nickel matrix and hinder defect movement, leading to greater mechanical strength. Moreover, nickel composite coatings offer improved protection against corrosion compared to pure nickel coatings. This review provides a detail discussion of nickel composite coatings with regard to their comparative advantaged compared to pure nickel coatings on different substrates.

Hybrid biomaterials were engineered using the electrospinning technique, incorporating the dipeptide Boc-L-phenylalanyl-L-Isoleucine into microfibers composed of biocompatible polymers. The examination by scanning electron microscopy affirmed the morphology of the microfibers, exhibiting diameters ranging between 0.9 to 1.8 µm. The dipeptide self-assemblies into spheres with a hydrodynamic size between 0.18 to 1.26 µm. The dielectric properties of these microfibers were characterized through impedance spectroscopy, where variations in both temperature and frequency were systematically studied. The investigation revealed a noteworthy rise in the dielectric constant and AC electric conductivity with increasing temperature, attributable to augmented charge mobility within the material. The successful integration of the dipeptide was substantiated through the observation of Maxwell-Wagner interfacial polarization, affirming the uniform dispersion within the microfibers. In-depth insights into electric permittivity and activation energies were garnered using the Havriliak-Negami model and the AC conductivity behavior. Very importantly, these engineered fibers exhibited pronounced pyroelectric and piezoelectric responses, with Boc-Phe-Ile@PLLA microfibers standing out with the highest piezoelectric coefficient, calculated to be 56 pC/N. These discoveries help us understand how dipeptide nanostructures embedded into electrospun nano/microfibers can greatly affect their pyroelectric and piezoelectric properties. They also point out that polymer fibers could be used as highly efficient piezoelectric energy harvesters, with promising applications in portable and wearable devices.

Glass fibers slowly dissolve and age when exposed to water molecules. Such a phenomenon also occurs when glass fibers are inside fiber-reinforced composites protected by the matrix. This en-vironmental aging results in the deterioration of the mechanical properties of the composite. In structural applications, GFRPs are continuously exposed to water environments for decades (typically design lifetime is around 25 years or even more). During their lifetime, these materials are affected by various temperatures, pH acidity levels, mechanical loads, and the synergy of these factors. The rate of the degradation process depends on the nature of glass, sizing, fiber orientation, and environmental factors such as acidity, temperature, and mechanical stress. In this work, degradation of typical industrial grade R-glass fibers, when inside an epoxy fiber-reinforced composite, is studied experimentally and computationally. A Dissolving Cylinder Zero-Order Kinetic (DCZOK) model was applied and could describe the long-term dissolution of glass composites, considering the influence of fiber orientation (hoop vs transverse), pH (1.7, 4.0, 5.7, 7.0, and 10.0), and temperature (20, 40, 60, and 80 °C). The limitations of the DCZOK model and effects of sizing protection, accumulation of degradation products inside the composite, and water availability were discussed. Experimentally dissolution was measured using ICP-MS. Like for the fibers, for GFRPs also, the temperature showed an Arrhenius-type influence on the ki-netics, increasing the rate of dissolution exponentially with increasing temperature. Similar to fibers, GFRPs showed a hyperbolic dependence on pH. The model was able to capture all of these effects, and the limitations were addressed.

The main idea of this paper is to investigate the exact solutions and dynamic properties in optical nanofibers, which is modeled by space-time fractional perturbed nonlinear schr\"odinger equation involving Kerr law nonlinearity with conformal fractional derivative. Firstly, by the complex fractional traveling wave transformation, the traveling wave system of the original equation is obtained, then a conserved quantity, namely the Hamiltonian is constructed, and the qualitative analysis of this system is conducted via this quantity by classifying the equilibrium points. Moreover, the prior estimate of the existence of the soliton and periodic solution is established via the bifurcation method. Furthermore, all exact traveling wave solutions are constructed to illustrate our results explicitly by the complete discrimination system for polynomial method.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

A novel electrospun nanofiber was developed using polyamide-6 (PA) and ε-poly-L-lysine (PL). PA is a popular textile polymer having desirable mechanical and thermal properties, chemical stability, and biocompatibility. However, PA nanofibers are prone to bacterial growth and user discomfort. PL, a natural homopolyamide, is non-toxic, antimicrobial, and hydrophilic but lacks spinnability due to its low molecular weight. Given its similar backbone structure as PA, with an additional amino side chain, PL was integrated with PA to develop multifunctional nanofibers. This study explores a simple, scalable method to obtain PL nanofibers by utilizing the structurally similar PA as the base. The goal was to enhance the functionality of PA by addressing its drawbacks. The study demonstrates spinnability of varying concentrations of PL with base PA while exploring compositions with higher PL concentrations than previously reported. Electrospinning parameters were studied to optimize the nanofiber properties. The effects of PL addition on morphology, hydrophilicity, thermal stability, mechanical performance, and long-term antimicrobial activity of nanofibers were evaluated. The inclusion of PL in PA-based nanofibers resulted in super hydrophilicity, increased tensile strength, and efficient antimicrobial properties with long-term stability. These enhanced characteristics hold promise for the composite nanofiber’s application in medical and protective textiles.