Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

Imitation learning, also known as programming by demonstration, has been shown to be a promising paradigm for intuitive robot programming by non-expert users. However, the classical kinesthetic approach with physical hand guidance suffers from generalizability across different robot types and is impractical for demonstrating tasks with long horizons. Visual imitation learning enables the recording of multi-step tasks as a single continuous video, allowing non-experts to demonstrate tasks naturally. Existing approaches typically require a large amount of data to develop end-to-end deep learning models that map raw pixels to robot actions. This paper explores the application of visual imitation learning from one-shot demonstration, significantly reducing the data requirements and simplifying the programming process. To achieve this target, a framework is proposed to map hand trajectories to the robot end-effector, consisting of four essential components: hand detection; object detection; segmentation of the trajectories into elemental skills; and learning the skills. Methods are developed for each component and evaluated on recorded videos to demonstrate the effectiveness of the proposed framework.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

Despite polycarbonate (PC) being a widely used engineering plastic, its notch and crack sensitivity pose challenges in critical applications. To address this, PC was blended with elastomeric polymers to explore the improvement in toughness. This study systematically investigates the toughening mechanisms of PC blended with acrylonitrile-butadiene-styrene (ABS), copolyether ester elas-tomer (COPE), and ABS and styrene-ethylene-butylene-styrene (SEBS) copolymer grafted with maleic anhydride (MA). The morphology and mechanical behavior were evaluated under qua-si-static and high-speed tensile tests and Charpy impact tests using optical, electronic, and atomic force microscopy and Raman spectroscopy. The morphological analysis reveals cavitation and crazing phenomena for COPE and SEBS-g-MA systems, and mostly debonding for ABS, indicating an improvement in toughening. While the addition of ABS improves the PC plastic deformation, modifying ABS with maleic anhydride enhances the elastic modulus. Blending PC with SEBS-g-MA increases the strain at break, and the addition of COPE significantly improves the deformation behavior of PC (by around 115%). This comparative study provides valuable insights into the performance of different PC-elastomer blends under similar conditions, supporting the selection of appropriate materials for given applications.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Microparticles derived from biomaterials are becoming increasingly popular for various applications, particularly in drug delivery systems. In this study, the water-in-oil (W/O) emulsification-diffusion method was used to create cellulose (C), silk fibroin (SF), and C/SF composite microparticles. We then observed the morphology of all obtained microparticles using scanning electron microscopy (SEM), evaluated their functional groups using attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and conducted thermogravimetric analysis using a thermogravimetric analyzer (TGA). SEM micrographs indicated that the native SF microparticles have the highest spherical shape with smooth surfaces. With blue dextran, the C microparticle was smaller compared to the native microparticle, while the drug-loaded SF microparticles were bigger than the native microparticle. The morphological surfaces of the C/SF composite microparticles were varied in shape and surface depending on the C/SF ratio used. The spherical shape of the C/SF composite microparticle was increased as SF content increased. Furthermore, the size of drug-loaded C/SF composite microparticles was gradually increased by the SF content. The significant functional groups in the C and SF structures were identified based on the ATR-FTIR data, and a suggestion was made regarding the interaction between the functional groups of each polymer. When compared to both native polymers, the C/SF composite microparticles exhibit improved thermal stability. The C/SF composite microparticle at a 1:3 ratio had the lowest drug release content, whereas the hydrophilicity of the C microparticle affected the highest drug release content. As a result, one crucial factor affecting the medication released from the microparticle is its thermal stability. According to the obtained results, C, SF, and C/SF composite microparticles show promise as delivery systems for drugs with controlled release.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

This study evaluates the efficiency of biodegradable polyurethane foams as thermal insulation materials compared to conventional materials like expanded polystyrene (EPS). Key parameters analyzed include thermal conductivity, energy savings, CO2 emission reductions, and investment payback periods. Biodegradable polyurethane foams demonstrated a thermal conductivity of 0.022 W/(m·K), significantly lower than EPS's 0.035 W/(m·K), leading to higher energy savings. Calculations reveal an annual energy saving of 443,820 kWh for polyurethane foams, compared to 441,330 kWh for EPS. Financially, polyurethane foams save approximately €53,258.4 annually, while EPS saves €52,959.6. In terms of environmental impact, polyurethane foams reduce CO2 emissions by 88,764 kg annually, versus 88,266 kg for EPS. Despite the higher initial cost of polyurethane foams (€50/m² compared to €30/m² for EPS), the payback period is remarkably short at 0.094 years (1.13 months) compared to EPS's 0.057 years (0.68 months). These findings highlight biodegradable polyurethane foams as a superior option for thermal insulation, offering significant energy, financial, and environmental benefits.

A Q-switched Nd:YAG laser was focused on Pb-Ti alloy samples in several Laser Induced Breakdown experiments in order to measure the Stark parameters of several spectral lines (58) of single ionized Titanium including the 3504.89 Å, and the 3510.83 Ålines (where we aported new experimental and theoretical values).Diagnostics of the laser induced plasmas (electron density and electron temperature) was performed using Balmer’s H alpha line (6562.7 Å).Temperatures were obtained by the Boltzmann Plot technique with spectral lines of Pb I (after correction for its evident self-absorption).Subsequently, calculations by the Griem approach of the Stark broadening parameters for several spectral lines were performed using the Gaunt factors proposed by Van Regemorter and those proposed by Douglas H. Sampson. In the latter cases the values obtained were very close to the experimental values. It allows us to assume that the calculations made for the spectral lines of Ti II, without experimental information, are more accurate using the Gaunt factors proposed by Sampson.

The self-assembly is an intriguing process of great importance in general soft matter and thus re-ceives an ever-growing scientific interest. Its most trivial example is the entropy-driven crystalli-zation of hard spheres. Past works have established the similarities and differences in the phase behavior of monomers and chains made of hard spheres. In the present work, inspired by the dif-ference in the melting points of the pure components, we study, through Monte Carlo simulations, the phase behavior of athermal mixtures composed of fully flexible polymers and individual monomers of uniform size. We analyze how the relative number fraction and the packing density affect crystallization and the established ordered morphologies. A synergetic effect is observed in the crystallization leading to synchronous crystallization of the two species. Structural analysis of the resulting ordered morphologies shows perfect mixing and thus no phase separation, which could split the system into polymer-rich and monomer-rich domains. Due to the constraints imposed by chain connectivity, the local environment of the individual spheres is systematically more spherical and more symmetric compared to the one of spheres belonging to chains. In general, increasing polymer content leads to reduction of the degree of crystallinity. According to the present findings, relative concentration is another determining factor to control the phase behavior of hard colloidal systems based on polymers.

Particles are considered temporarily identical if the interchange of these particles does not cause any observable physical effects within a time interval Δt. An indistinguishability hypothesis is proposed for such particles, suggesting that two particles (or systems) with nearly the same degree of internal freedom will actually interchange under certain circumstances, thereby affecting the subsequent dynamics. This indistinguishability implies that, theoretically, it is possible to capture an elementary particle with extraordinarily large internal freedom by trading it for an isolated composite system of ordinary matter particles with almost the same total internal freedom as the large-freedom particle. Following this, the ordinary particles will instantly disperse into the environment, while the large-freedom particle will initially be captured and then gradually delocalized into the environment, an observable phenomenon. If this hypothesis is proven true in the future, it might provide a novel strategy for detecting dark matter particles.

Recently, polyacetylene (PA) is receiving a renewed scientific attention due to its electrical properties potentially useful for energy applications (e.g., fabrication of electrodes for batteries and supercapacitors) and unique functional characteristics (e.g., flame retardant, oxygen scavenger, EMI-shielding, etc.). This chemical compound can be obtained in form of a polyacetylene-PVOH copolymers simply by chemical dehydration of poly(vinyl alcohol) (PVOH), which is a very common type of polymer, widely used in packaging and other technological areas. This very inexpensive chemical reaction for the large-scale synthesis of PA/polyvinylenes has been investigated by reacting PVOH with fuming sulfuric acid at room temperature. In this process, PVOH, shaped in form of film, is dipped in fuming sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration, it has been mechanically removed from the liquid phase by using a nylon sieve. The reduction process leads to a substantial PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. The reaction product has been also characterized by UV-Vis spectroscopy in order to evidence the presence in the structure of conjugated carbon-carbon double bonds of various lengths. Differential scanning calorimetry (DSC) and thermogravimetric analysis have been used respectively to investigate the PA solid-state cis-trans isomerization and thermal stability in air and nitrogen, respectively.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

The dielectric constant (ε) reflects the ability of a material to align and orient electrical dipoles within its structure in response to an externally applied electric field; the greater the polarizability of molecules, the greater the value of dielectric constant. In this study a data set of 86 polymers was investigated to develop a structure-property quantitative relations (QSPR) model to predict the dielectric constant in polymers. An initial set of 1273 descriptors was used to select a best set of descriptors and to construct two machine learning models with Gradient Boosting Regressor (GB_A and GB_B). The best performing model (GB_A) with 8 descriptors, exhibited a performance of (R2train) = 0.938 and (R2test) = 0.802. The models were internally validated by 5 folds cross-validation, demonstrating robustness. Additionally, using the Accumulative Local Effect (ALE) technique, we analyzed the relationship between the 8 descriptors involved and the impact of these descriptors to dielectric constant of polymers.

(1) Background: A wide literature based on loading and unloading bending tests has been carried out over the half past century for assessing the force released by superelastic wires. The aim of this investigation is not only to characterize a broadly described superelastic NiTi and a novel CuNiTi archwire, but also to provide novel insights into the load vs deflection profiles. A harmonic scenario for superelastic wires will be shown as temperature is kept constant at 37°C. However, a completely different picture will be highlighted as a temporary heating step up to 50°C is introduced within the force vs deflection profiles. (2) Methods: A variety of NiTi and a novel CuNiTi round and rectangular cross-section archwires have been investigated. Static 3-point bending tests up to a deflection level of 3.0 mm have been carried out for detecting the unloading force plateau levels occurring at 37°C. A hold deflection step of 5 min at deflection levels occurring along the unloading plateau extension is introduced. The effect of a temporary heating up to 50°C on the force plateau level released by the investigated wires is analyzed. (3) Results: Mechanical profiles suggest that the plateau force levels detected at 37°C are consistent with those broadly reported in the literature, but they only represent a single block puzzle of the force scenario that a superelastic wire releases during the orthodontic treatment. (4) Conclusions: Once a superelastic wire is bent and clinically applied, the effect of a temporary heating up to 50°C (e.g. hot food or drink ingestion) produces a significant plateau force increase whose magnitude depends on the deflection level. The highest force increase of about 50% and 40% have been detected at deflection levels located at the beginning of the unloading plateau extension for NiTi and CuNiTi wires, respectively.

There are various types of charged particles in the space environment, which can cause different types of radiation damage to materials and devices, leading to on-orbit failures and even accidents of spacecraft. Developing lightweight and efficient radiation shielding materials is an effective approach to improve the inherent protection of spacecraft. The protective performance of different materials against proton and electron spectra in the Earth’s radiation belts is evaluated by Geant4 simulation. Based on the simulation results, suitable hardening components are selected to design composite materials, and B4C/PEEK composites with different B4C content were successfully prepared. Experimental results demonstrate that the simulated and experimental results for the electron, proton and neutron shielding performance of B4C/PEEK composites are consistent. These composites exhibit excellent radiation shielding capabilities against electrons, protons and neutrons, and the radiation protection performance improves with increasing B4C content in the B4C/PEEK composite materials.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

The release of the active substance from the matrix modified-release tablets based on Kollidon®SR and chitosan depends on its solubility in the dissolution medium and on the composition of the matrix-forming polymers. The study is based on new oral matrix tablets based on Kollidon®SR and chitosan, formulated to optimize the low oral bioavailability of chlorzoxazone, a non-steroidal anti-inflammatory drug, a class II Biopharmaceutical Classification System. Nine types of chlorzoxazone matrix tablets were obtained using the direct compression method, and their combination at 1:1, 1:2, 1:3 chlorzoxazone/ excipients, 20%-40% (w/w) Kollidon®SR, 3-7% (w/w) chitosan and the auxiliary substances were formulated in constant concentrations. Pharmaco-technical characterization included the analysis of flowability and compressibility properties (flow time, friction coefficient, angle of repose, Hausner ratio, Carr Index), and of pharmaco-chemical characteristics (mass and dose uniformity, thickness, diameter, mechanical strength, Friability, degree of softening, in vitro release profile) of the tablets. Based on the initial evaluation of the pharmaco-technical analysis, pharmaco-chemical characteristics, and in vitro release profile, only three matrix tablet formulations (F1b, F2b, and F3b) were further tested. They were evaluated through Fourier-transform infrared spectrometry, X-ray Diffraction, thermogravimetry, differential scanning calorimetry, and in vitro dissolution tests. The three formulations were comparatively studied regarding the release kinetics of active substances using in vitro release testing. The results were analyzed by fitting into four representative mathematical models for the modified release oral formulations. In vitro kinetic study reveals a complex mechanism of release occurring in the first (0 - 2 hours) and second (2.0 hours – 36 hours) steps of drug release. Two factors have been calculated to assess the release profile of chlorzoxazone: f1 - the similarity factor and f2 - the factor difference. The results have shown that both Kollidon®SR and chitosan may be used as matrix-forming agents when combined with chlorzoxazone. In vitro dissolution tests revealed the F2b sample, data suggesting a faster drug release. The three formulations showed optimum pharmaco-technical properties and in vitro kinetic study, and they had tremendous potential to be used in oral pharmaceutical products for the controlled delivery of chlorzoxazone.

Nanomaterials have shown significant promise for enhancing the performance of composite materials and increasing their functionality for various industrial applications. This review explores the unique properties of nanomaterials, particularly carbon-based nanomaterials, and provides key findings in utilizing them to enhance composite performance. It highlights specific nano-based composite materials and their significant potential in advancing the field of nanocomposites. Challenges associated with nanocomposite production and utilization are also discussed, along with possible solutions to address them. Finally, the study provides recommendations for continued research and innovation in nanocomposites to fully unlock the benefits of these advanced materials for broader future applications.

For the past few decades, researchers have been intrigued with glassy polymers, which have applications ranging from gas separations to corrosion protection to drug delivery systems. The techniques employed to examine the sorption and diffusion of small molecules in glassy polymers are the subject of this review. Diffusion models in glassy polymers are regulated by Fickian and non-Fickian diffusion, with non-Fickian diffusion being more prevalent. The characteristics of glassy polymers are determined by sorption isotherms, and different models have been proposed in the literature to explain sorption in glassy polymers during the last few years. This review also includes the applications of glassy polymer. Despite having so many applications, current researchers still have difficulty in implementing coating challenges due to issues like as physical ageing, which is briefly discussed in the review.

In this paper, a novel microwave catalyst Ni@SiC/CNFs (NSC), C/Ni (NC), and C/SiC (SC) were successfully synthesized by electrostatic spinning method, and proved to degrade methylene blue with high efficiency under microwave irradiation. The results imply that the catalyst Ni@SiC/CNFs with double shell structure gave a 99.99 % removal rate in 90 s for the degradation of methylene blue under microwave irradiation, outperformed the C/Ni and C/SiC and most other reported catalysts in similar studies. On the one hand, the possible mechanism of the methylene blue degradation should be ascribed to that double shell structure increases the polarization source of the material, resulting in excellent microwave absorption properties; and on the other, the in-situ generation of active species OH• and O2 - under microwave radiation and the synergistic coupling effect of metal plasma greatly improved the degradation efficiency of methylene blue. The findings of this study could provide a valuable reference for the green degradation of industrial dye wastewater and its sustainable development process.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

The interest in obtaining new composite materials with diverse properties has created a growing interest in natural fi-bers as reinforcement in polymers, which has generated an impact in sectors such as automotive and construction, dis-placing synthetic fibers. Properties such as low density, low cost, and rene.wable make these fibers an attractive alterna-tive to reduce environmental impact. Their application in polymers, such as polypropylene, polyethylene, and epoxy resins, has allowed the modification of polymeric composite materials' mechanical and physical properties (NFRP). This review focuses on investigating the status of natural fiber-reinforced polymers. It analyzes their worldwide demand, chemical characteristics, physical and mechanical properties, and various applications in different sectors and indus-tries. In addition, the advantages and disadvantages of NFRPs are highlighted, highlighting their potential for new ap-plications.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P &gt; 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA &gt; 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Two-dimensional layered coordination polymers based on the hetero-substituted 3-chloro-6-cyano-2,5-dihydroxybenzoquinone ligand, hereafter ClCNAn2- anilate, and LnIII ions (Tb and Eu) are reported. Compounds 1, 2, formulated as Ln2(ClCNAn)3(DMSO)6 (LnIII = Tb, 1; Eu, 2) and their related intermediates 1’ and 2’, formulated as Ln2(ClCNAn)3(H2O)x.yH2O (x+y likely = 12, Ln = Tb, 1’; and Eu, 2’) were prepared by a conventional one-pot reaction (the latter) and recrystallized from DMSO solvent (the former). Polyhydrated intermediates 1’ and 2’ show very similar XRPD patterns, while, despite their common stoichiometry, 1 and 2 are not isostructural. 1 consists of a 2D coordination framework of 3,6 topology, where [Tb(DMSO)3]3+ moieties are bridged by three bis-chelating ClCNAn2- ligands, forming distorted hexagons. Ultrathin nanosheets of 1 were obtained by exfoliation, via liquid assisted sonication method and characterized by atomic force microscopy, confirming the 2D nature of 1. The crystal structure of 2, still showing the presence of 2D sheets with “hexagonal” mesh and a common (3,6) connectivity, is based onto flat, non-corrugated slabs. Indeed, at a larger scale, the different “rectangular tiles” show a clear roofing in 1, which is totally absent in 2. The magnetic behavior of 1 very likely indicates depopulation of the highest crystal-field levels, as expected for TbIII compounds.

This study aims to investigate the effects of cement kiln dust (CKD) on the hydration reactions and mechanical properties of cement and to evaluate its potential for use as a supplementary cementitious material (SCM). The key variables are the CKD type and incorporation rate. Cement paste and mortar specimens containing CKD were prepared to examine their effects on the cement hydration and mechanical properties. The impact on hydration was assessed using setting time measurements, heat of hydration tests, and thermogravimetric analysis (TG). In addition, compressive strength tests were conducted to evaluate the effect of CKD on the mechanical properties of the cement. The results indicated that CKD promoted early cement hydration and enhanced the early age mechanical properties. However, owing to its lack of pozzolanic reactivity, it did not significantly affect long-term hydration. Given that the effects of CKD vary slightly depending on its chemical composition, careful consideration of CKD's properties suggests that its potential use as a SCM is promising.

In the construction sector, the integration of biobased materials has emerged as a pivotal aspect of EU policies, aimed at promoting sustainable practices throughout the value chain to mitigate resource consumption and carbon emissions. This paper explores the development and validation activities of a bio-based façade system within the Basajaun H2020 project, focusing on enhancing the utilization of biobased components within building envelopes to replace conventional solutions with eco-friendly alternatives. This paper reports the methodologies employed to detect requirements and outline the testing protocols undertaken to validate the façade system design devised within the project focusing on the original façade components as the bio composite profile. Vision and opaque façade modules are prototyped and tested following curtain wall standards standard for performance and acoustic assessments, to showcase the efficacy of the developed solution. The conducted tests demonstrate the feasibility of integrating bio-based components into building envelopes, aligning with project expectations, and prevailing standards for curtain wall façade solutions. Notably, the designed façade system meets technical conditions and project objectives. Nevertheless, the research underscores the need for further refinements to facilitate solution industrialization and explore broader market applicability. Future efforts will focus on addressing these improvements and assessing the scalability of the solution.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

Variable-Angle Tow (VAT) laminates can improve straight fiber composites mechanical properties thanks to the application of curvilinear fibers. This characteristic allows to achieve ambitious objectives for design and performance purposes. Nevertheless, the wider design space and the higher number of parameters result in a more complex structural problem. Among the various approaches that have been used for VATs study, Carrera’s Unified Formulation (CUF) allows to obtain multiple theories within the same framework, guaranteeing a good compromise between the results accuracy and the computational cost. In this article, the linear buckling behavior of VAT laminates is analyzed through the extension of CUF 2D plate models within the Reissner’s Mixed Variational Theorem (RMVT). Results show that RMVT can better approximate the prebuckling non-uniform stress field of the plate when compared to standard approaches, thus improving the prediction of the linear buckling loads of VAT composites.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

In this work, the properties of a composition based on synthetic rubber ethylene-propylene ter-polymer and polymers with functional groups of the mixture are studied. Low efficiency of some compositions based on ethylene and propylene copolymer limits their use in the production of tires and rubber products. Therefore, we conducted a study to improve the disadvantages of SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) The data obtained showed that a number of its indicators of rubber based on them were improved. Tear resistance, resistance to repeated stretching increased, adhesion of the composition to metal, chemical resistance increased, the degree of swelling in benzene and gasoline-benzene mixture decreased. Compositions based on the mixture SREPT-60 using butyl rubber + choro polyisoprene + butadiene-nitrile + butadiene styrene rubber and adding a plasticizer to the composition = α, methacrylate-(bis-diethylene glycol phthalate) -(btegf-9) +Dioctyl phthalate: (70:20:10) have high resistance to swelling in an aggressive environment (Benzene, gasoline, alcohol, acid, oil, etc.) mixture.

Soft pneumatic actuators/robotics have received significant interest in the medical and health fields, due to their intrinsic elasticity and simple control strategies enabling desired interaction. However, current soft hand pneumatic exoskeletons often exhibit uniform deformation, mismatch the profile of the interacted objects, and seldom quantify the assistive effects during activities of daily life (ADL), such as extension angle and joint stiffness predicted. The lack of quantification poses challenges to the effective and sustainable advancement of rehabilitation technology. This paper introduces the design, modeling, and testing of pneumatic bioinspired Segmented Composite Proprioceptive Bending Actuators (SCPBAs) for hand rehabilitation in ADL tasks. The actuator’s soft-joint/rigid-bone segmented structure, inspired by the human finger anatomy, provides a superior fit compared to traditional continuous structures. A quasi-static model is established to predict the bending angles based on geometrical parameters. The SCPBAs also include a quantitative evaluation of joint stiffness and extension angle utilizing proprioceptive bending information. Additionally, a soft under-actuated hand exoskeleton equipped with SCPBAs demonstrates its potential in ADL rehabilitation scenarios.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

The capability of radially polymerized bio-dendrimers and hyperbranched polymers for medical applications is well established. Among them, perhaps the most important are those that involve interactions with the regenerative mechanisms of cells. Dendritic polymers due to their distinctive architecture may play a multitude of roles such as protein biomimicry (collagen, elastin, hydroxy apatite production), gene and drug delivery (cell differentiation, antimicrobial protection), surface chemistry and charge modulation (adhesion to cells and tissues), polymer cross-linking (eye, skin and internal organ wound healing). The review highlights all the different categories of hard and soft tissues that may be remediated with their contribution. The reader will be also exposed to the incorporation methods to established biomaterials such as scaffolds, the functionalization strategies, and the synthetic paths for the assembly from biocompatible building blocks and natural metabolites.

Silicon (Si) is the major material of semiconductor element. For semiconductor element producing, Si need to refined into high-purity silicon crystals, which has the approximate characteristics of intrinsic semiconductor, then doping 13th group or 15th group trace element. Producing the high-purity silicon crystals with well-lattice structure need a lot of energy and highly cost. Besides, the high-purity silicon is very hard and fragile which limits the scope of application. For this reason, this study added low-grade non-complete lattice silicon in the elastic polymer, and then doped with high concentrations of fine carbon powder. This material can be conductive by physisorption;therefore, it can be used to making semiconductors. Using this material to produce electronic components can significantly reduce the cost of purification and crystallization, saving energy at the same time. Moreover, because this elastic polymer materials containing silicon, which has soft, warm, and durable physical properties. With those properties, the design of the device could be more flex, full scalability and close to the skin.

We present results on the spontaneous crystallization of freely-jointed polymers of hard spheres obtained in an unprecedentedly long Monte Carlo (MC) simulation on a system of 54 chains of 1000 monomers. Starting from a purely amorphous configuration and after a transitory dominance of the hexagonal closed packed (HCP) polymorph, the system crystallizes in a final, stable, face centered cubic (FCC) crystal of very high perfection. Through refined metrics we gauge the degree of ordering and identify the regions of the phase transition and the corresponding morphologies. An analysis of chain conformational characteristics, of the spatial distribution of monomers and of the volume accessible to them shows that the phase transition is caused by an increase in translational entropy that is larger than the loss of conformational entropy of the chains in the crystal compared to the amorphous state. Polymer chains in the crystal adopt ideal random walk statistics as their great length renders local conformational details, imposed by the geometry of the FCC crystal, irrelevant.

Flexibility of polymers defined by an equation in 2019 is related here to thermal conductivity, using reliable data for both properties found in the literature. The resulting equation is simple, it has the form of a quadratic polynomial. The goodness of the fit represented by R² = 0.975, while R² = 1 represents a perfect fit. Thus, knowledge of one of these properties can be used for calculation of the other one. The present results are a part of a larger program enabling obtaining by calculation pertinent properties of polymers from other properties for which data are available.

The effective treatment for chronic wounds constitute one of the most common worldwide health care problem due to the presence of high levels of proteases, free radicals and exudates in the wound, which constantly activate the inflammatory system avoiding the tissue regeneration. In this study, we describe a multifunctional bioactive and resorbable membrane with in-built antioxidant agent for the continuous quenching of free radicals as well as to control inflammatory response helping to promote the wound healing process. To reach that goal synthesized statistical copolymers of N-vinylcaprolactam (V) and 2-hydroxyethyl methacrylate (H) have been conjugated with catechol bearing hydrocaffeic acid (HCA) molecules. The natural polyphenol (catechol) is the key molecule responsible for the mechanism of adhesion of mussels, and provides the functionalized polymer conjugate a continuous antioxidant response, antiinflammatory effect, UV screen and bioadhesion in the moist environment of the human body, all of them key features in the wound healing process. Therefore, these novel mussel-inspired materials have an enormous potential of application and can act very positively, favoring and promoting the healing effect in chronic wounds.

This review is focused on current state-of-the-art research on electroactive-based materials and their synthesis, as well as their physicochemical and biological properties. Special attention is paid to pristine intrinsically conducting polymers (ICPs) and their composites with other organic and inorganic components, well-defined micro- and nanostructures, and enhanced surface areas compared with those of conventionally prepared ICPs. Hydrogels, due to their defined porous structures and being filled with aqueous solution, offer the ability to increase the amount of immobilized chemical, biological or biochemical molecules. When other components are incorporated into ICPs, the materials form composites; in this particular case, they form conductive composites. The design and synthesis of conductive composites result in the inheritance of the advantages of each component and offer new features because of the synergistic effects between the components. The resulting structures of ICPs, conducting polymer hydrogels and their composites, as well as the unusual physicochemical properties, biocompatibility and multi-functionality of these materials, facilitate their bioapplications. The synergistic effects between constituents have made these materials particularly attractive as sensing elements for biological agents, and they also enable the immobilization of bioreceptors such as enzymes, antigen–antibodies, and nucleic acids onto their surfaces for the detection of an array of biological agents. Currently, these materials have unlimited applicability in biomedicine. In this review, we have limited discussion to three areas in which it seems that the use of ICPs and materials, including their different forms, are particularly interesting, namely, biosensors, delivery of drugs and tissue engineering.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

A novel scaffold design has been created to enhance tissue engineering and regenerative medicine by optimizing the controlled, prolonged release of hepatocyte growth factor (HGF), a powerful chemoattractant for endogenous mesenchymal stem cells. We present a new stacked scaffold that is made up of three different fibrin gel layers, each of which has HGF integrated into the matrix. The design attempts to preserve HGF's regenerative properties for long periods of time, which is necessary for complex tissue regeneration. These multi-layered fibrin gels have been mechanically evaluated using rheometry, and their degradation behavior has been studied using D-Dimer ELISA. Understanding the kinetics of HGF release from this novel scaffold configuration is essential for understanding HGF's long-term sustained bioactivity. A range of cell-based tests were carried out to verify the functionality of HGF following extended incorporation. These tests included 2-photon microscopy using phalloidin staining to examine cellular morphology, SEM analysis for scaffold-cell interactions, and scratch and scatter assays to assess migration and motility. The analyses show that the novel stacking scaffold promotes vital cellular processes for tissue regeneration in addition to supporting HGF's bioactivity. This scaffold design was developed for in situ tissue engineering. Using the body as a bioreactor, the scaffold should recruit mesenchymal stem cells from their niche thus combining the regenerative abilities of HGF and MSCs to promote tissue remodeling and wound repair.

This study focuses on enhancing controllable fibrin-based hydrogels for tissue engineering, addressing existing weaknesses. By integrating a novel copolymer, we improve the foundation for cell-based angiogenesis with adaptable structural features. Tissue engineering often faces challenges like waste disposal and nutrient supply beyond the 200 µm diffusion limit. Angiogenesis breaks through this limitation, allowing the construction of larger constructs. Our innovative scaffold combination significantly boosts angiogenesis, resulting in longer branches and more capillary network junctions. The copolymer attached to fibrin fibers enables precise adjustment of hydrogel mechanical-dynamic properties for specific applications. Our material proves effective for angiogenesis, even under suppression factors like suramin. In our study, we prepared fibrin-based hydrogels with and without the copolymer PVP12400-co-GMA10mol%. Using a co-culture system of human umbilical vein endothelial cells (HUVEC) and mesenchymal stem cells (MSC), we analyzed angiogenetic behavior on and within the modified hydrogels. Capillary-like structures were reproducibly formed on different surfaces, demonstrating the general feasibility of three-dimensional endothelial cell networks in fibrin-based hydrogels. This highlights the biomaterial's suitability for in vitro pre-vascularization of biohybrid implants.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

Purpose: The purpose of this study is to apply the Composite Radiographic Index modified (CRIm) in CBCT scans of patients with Medication related osteonecrosis of the jaws (MRONJ) in order to detect its validity, and corelate the radiologic findings with the clinical staging of the disease. Methods: This study included 43 patients with MRONJ diagnosis and CBCT scans performed in the School of Dentistry and approved by the Research Ethics Committee. Clinical staging for every patient (0-3) was provided according to AAOMS 2022 guidelines. In cases of patients with both jaws affected, each jaw was evaluated independently resulting to 52 CBCT scans. The 52 CBCT scans were assessed under standardized viewing conditions by 2 observers who evaluated independently the following 8 radiologic features: lytic changes, sclerosis, periosteal reaction, sequestration, non-healing extraction sockets and other findings (sinus implication, inferior alveolar canal involvement, jaw fracture). The CRIm index was constructed to assess the extent of osseous changes. The radiologic features were scored as absent (0), localized/single (1), extensive/multiple (2), yielding a theoretical range of 0–12. For statistical analysis Fisher’s exact test and Spearman’s correlation coefficient were performed. Results: A statistically significant association of clinical stage with lytic changes, sequestration and inferior alveolar canal involvement was found. Also, a statistically significant correlation of clinical stage with CRIm index classification was obtained. Conclusions: The CRIm index tends to increase as the clinical stages of MRONJ advance, suggesting a correlation between the clinical stage of MRONJ and the CRIm index.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Wear-resistant steel/carbon steel composite plate not only has the double performance advantage of high strength and wear-resistance, but also can reduce energy consumption and production cost. Based on 50% reduction rate, the wear resistance of BTW1/Q345 composite was studied at different annealing temperatures, and the dry friction and wear tests of BTW1/Q345 composite at different annealing temperatures were carried out by using RETC MFT-5000. The macro-micro morphology and wear mechanism of wear marks at different annealing temperatures were analyzed by using white light interference three-dimensional surface profiler, Scanning electron microscope scanning electron microscope (SEM) and backscatter electron diffraction (EBSD) . The results show that with the increase of annealing temperature, the grain size near the scratch of BTW1 in the wear-resistant layer of the composite plate is refined, and the wear-resistant property is higher than that of the original sample.When the annealing temperature is 860℃,the wear resistance is the best.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

(1) Background: The aim of this investigation is to determine the effect of archwires’ deflection on the temperature transitions driving the austenite to martensite transformation (and vice versa) and the force released by NiTi and CuNiTi orthodontic wires. (2) Methods: Round cross-section archwires have been investigated. The calorimetric approach has been used for measuring transition temperatures occurring in the unstressed (e.g. undeflected) state of the wires. Static Thermo-mechanical analysis in a temperature controlled wet environment has been performed in the range of temperature between 5°C and 55°C for measuring temperature transitions occurring in highly deflected archwires in conjunction with the force released by these wires. (3) Results: Plateau forces investigated in Part I and those reported in the literature describes the wire’s behaviour only at deflection levels close to the end point of the force plateau extension detected at 37°C. Upon heating or cooling, the austenite finish (Af) transition temperature and the martensite start (Ms) temperature largely depends on the deflection level for both NiTi and CuNiTi. (4) Conclusions: The plateau force levels at 37°C, broadly reported in the literature, only represent the lower boundary force that a superelastic wire releases at 37°C above its elastic limit. For both NiTi and CuNiTi, plateau force levels at 37°C can be predicted by the static TMA profile matching the end point of the force plateau extension. Transition temperatures in largely deflected wires are significantly higher than those determined through the calorimetric approach.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

Molecularly imprinted polymers (MIPs) have been widely used in nanomedicine during the last few years. However, their potential is limited by their intrinsic properties resulting, for instance, in lack of control in drug release processes or complex detection for in vivo imaging. Recent attempts in creating hybrid nanomaterials combining MIPs with inorganic nanomaterials succeeded in providing a wide range of new interesting properties suitable for nanomedicine. Through this review, we aim to illustrate how hybrids molecularly imprinted polymers may improve patient care with enhanced imaging, treatments and combination of both.

A method for measuring the mechanical parameters of viscoelastic polymers by nanoindentation technology was proposed and verified. Through the mechanical response of load-displacement curves at different loading rates, then creep compliances and relaxation modulus were fitted. Polyimide thin film was employed in this research and experiments for five different loading rates were conducted. The fitting load-displacement loading curves obtained by the inversion method were identical to the experimental curves at five different loading rates，confirming the validity of the method. Moreover, with the loading rates increased，the fitting curves were more consistent commensurately with the nanoindentation experiment. DMA experiments were tested, and the generalized Kelvin/ Maxwell model were used for fitting experiment data. Results from DMA tests generally agree well with data from nanoindentation method, thereby verifying the feasibility of the method. The Prony series obtained by the two methods were used to simulate the creep experiments, which further verified the method.

This study addresses the enhancement of material efficiency and reduction of brittleness in timber-to-concrete adhesive connections for beam-type timber and timber-concrete composite panels. The research explores the potential benefits of adding longitudinal timber ribs to Cross-Laminated Timber (CLT) beam-type panels. Three groups of flexure-tested specimens were analysed: (1) timber panels (1400 mm × 400 mm) with two 100 mm thick CLT panels and two 60 mm thick CLT panels reinforced with 150x80 mm timber ribs; (2) eight specimens (600 mm × 100 mm × 150 mm) with CLT members (600 mm × 100 mm × 100 mm) connected to a 50 mm concrete layer using granite chips and Sikadur-31 (AB) epoxy adhesive; (3) six CLT panels (1400 mm × 400 mm × 50 mm) bonded to a 50 mm concrete layer, with two panels containing polypropylene microfibers and two panels incorporating polyethene dowels for mechanical connection. Specimens were subjected to three-point bending tests and analysed using the transformed section method, γ-method, and finite element method with ANSYS 2023R2 software. Results indicated a 53% increase in load-carrying capacity for ribbed CLT panels with no additional material consumption, a 24.8%-41.1% increase for CLT panels strengthened with a concrete layer, and improved ductility and prevention of disintegration in timber-concrete composites with polypropylene microfibers.

This review summarizes the most recent developments of research on protozoan parasite infections ac-quired through food and drinking water and is aimed at gathering updated knowledge on the risk factors, illnesses caused, and measures for prevention. Reports included dated from 2019 to the present and regarded recent outbreaks and cases of severe infec-tions, prevalence in different population segments and food handlers, and occurrence in food and drinking water. Cryptosporidium spp., Entamoeba histolytica, Giardia intestinalis, Trypanosoma cruzi and Toxoplasma gondii were the microorganisms most frequently involved in large outbreaks and/or severe infections, while Cyclospora cayetanensis was most frequently involved in single case reports. Cystoisospora belli was implied in severe infections in immunocompromised patients, while Blastocystis homi-nis, Sarcocystis spp., Dientamoeba fragilis, Endolimax nana and Pentatrichomonas hominis appeared to be less relevant for number of symptomatic infections and pathogenic potential. A progressive improvement in surveillance of protozoan infections and infection sources was highlighted, especially in developed countries. The apparent increase in cases was concomitant with the implementa-tion of reporting systems and the application of molecular diagnostic methods that represent valuable in-struments for establishing epidemiological links and preventing or limiting outbreaks. The pathogenic role and sources of infection should be better elucidated for some species.

Biocomposite membranes based on polylactic acid (PLA) and cellulose nanocrystals (CNCs) were developed using a scientific approach. Dicumyl peroxide (DCP) was used as a polymerization ini-tiator, while tin octoate (Sn(Oct)2) and triphenylphosphane (P(C6H5)3) were used as catalysts. A torque rheometer was used to mix the components of the biocomposite, and thin films was prepared by solvent casting. Fourier transform infrared (FTIR) spectroscopy confirmed the coupling between the PLA and CNCs. Field emission scanning electron microscopy (FESEM) showed that the CNCs were well-dispersed in the PLA matrix with an unimodal particle size distribution and a maximum particle size of around 200 nm. Thermogravimetric analysis (TGA) and differential scanning calo-rimetry (DSC) analysis demonstrated good thermal stability and improved biodegradability of the biocomposite membrane compared to pure PLA. Mechanical characterization showed a Young's modulus of 1.65 GPa, which is comparable to that of other composite materials, and a maximum tensile strength of 20.31 MPa, which is higher than that of pure PLA. These results suggest that the developed biocomposite membrane has potential applications in water filtration, food packaging, and biomedical devices.

As a result of this work, a previously unreported benzoxazine monomer based on 3,3'-dichloro-4,4'-diaminodiphenylmethane was obtained, characterized by 1H and 13C NMR spectroscopy, and its thermal and rheological properties were studied. A comparison between the properties of benzoxazines based on diamines (3,3'-dichloro-4,4'-diaminodiphenylmethane and 4,4’-diaminodimethylmethane). The effect of the reaction medium on the structure of the oligomeric fraction and the overall yield of the main product was studied. The synthesized monomers can be used as thermo- and fire-resistant binders for polymer composite materials, as well as hardeners for epoxy resins.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

Maxillofacial defects, arising from trauma, oncological disease or congenital differences, detrimentally affect everyday life. Prosthetic repair offers the aesthetic and functional reconstruction with the help of materials mimicking natural tissues, among which polymers take unprecedented role. The three-dimensional (3D) printing techniques based on the computer-aided design, where polymers are essential, provide a rapid and cost-effective workflow protocol to perfectly restore patient-specific anatomy for prosthetics. This review discusses the main 3D printing approaches to maxillofacial prostheses fabrication: extrusion and lithography, which are radically preferable to the traditional methods. The main assessment criteria, affording the polymer implementation in 3D printing of prostheses, as well as the characteristics of the key advanced polymers, are considered. The success of the prosthesis is shown to be largely dependent on the retention system, predominantly using polymers in the form of adhesives and osseointegrated implants as a support for the prosthesis. The approaches and technological prospects are also discussed in the context of specific aesthetic restoration on the example of the nasal, auricle and ocular prostheses. 3D printing techniques determine the development of personalized approaches to improve aesthetic and functional effect of prosthetics in patients with maxillofacial defects.

Limonene epoxide (1,2 limonene oxide) readily reacts with carbon dioxide in a ring opening copolymerization reaction with insertion of CO₂ and formation of polycarbonates of exceptional chemical and physical properties. Both poly(limonene carbonate) and poly(limonene dicarbonate) can be synthesized using low cost Zn or Al homogeneous catalysts. This study addresses selected relevant questions concerning the technical and economic feasibility of limonene and carbon dioxide polymers en route to the bioeconomy.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Radially polymerized dendritic compounds are nowadays an established polymer category next to their linear, branched and cross-linked counterparts. Their uncommon tree-like architecture is characterized by adjustable internal cavities and external groups. They are therefore exceptional absorbents and this attainment of high concentrations into their interior renders them ideal reac-tion media. In this framework they are applied in many environmentally benign implementa-tions. One of the most important among them is water purification though pollutant decomposi-tion. Simple and composite catalysts and photo-catalysts containing dendritic polymers and ap-plied in water remediation will be discussed jointly with some unconventional solutions and fu-ture prospects.

Cranio-maxillofacial structure is a region of particular interest in the field of regenerative medicine due to both its anatomical complexity and the numerous abnormalities affecting this area. However, this anatomical complexity is what makes possible the coexistence of different microbial ecosystems in the oral cavity and the maxillofacial region, contributing to the increased risk of bacterial infections. In this regard, different materials have been used for their application in this field. These materials can be obtained from natural and renewable feedstocks or by synthetic routes with desired mechanical properties, biocompatibility and antimicrobial activity. Hence, in this review, we have focused on bio-based polymers, which by their own nature, by chemical modifications of their structure, or by their combination with other elements, provide a useful antibacterial activity as well as the suitable conditions for cranio-maxillofacial tissue regeneration. This approach has not been reviewed previously, and we have specifically arranged the content of this article according to the resulting material and its corresponding application, reviewing guided bone regeneration membranes; bone cements; and devices and scaffolds for both soft and hard maxillofacial tissue regeneration, including hybrid scaffolds, dental implants, hydrogels and composites.

Exploring for green and affordable protection of perishable fruit like cherry tomato is of significance. Here the protective efficacy and its underpinnings of coating with oleaster gum, alone or incorporated with cuminal, on cherry tomatoes stored at ambient temperature were investigated. The composite coating of oleaster gum with 0.1% cuminal reduced decay, respiration rate, weight loss, and softening of the fruit and decelerated their decreases of total soluble solids, titratable acidity, and soluble proteins, and therefore maintained their marketability. Furthermore, it reduced the accumulation of O•− 2and H2O2 in fruit, and mitigated cell membrane lipid oxidation and permeabilization, thereby retarding their senescence. Instrumentally, it elevated the activities of superoxide dismutase, catalase, peroxidase, and ascorbate peroxidase and the levels of ascorbic acid and glutathione. This potentiation of the fruit antioxidant system makes the composite coating a promising approach to keeping the postharvest quality of perishable fruit.

A new method for the synthesis of azido-propargyloxy derivatives of 1,3,5-triazine has been developed. The antibacterial activity against E. coli bacteria of propargyloxy substituted 1,3,5-triazines - 2,4,6-trispropargyloxy-1,3,5-triazine, 2-azido-4,6-bispropargyloxy-1,3,5-triazine and 2,4-diazido-6-propargyloxy-1,3,5-triazine and their hyperbranched polymers. It has been shown that the presence of an azide group in the compound directly affects the antibacterial activity. The cytotoxicity of these compounds against the M-HeLa, FetMSC and Vero cell lines was studied. The IC50 value was determined for low molecular weight compounds. It has been shown that hyperbranched polymers without azide groups don’t exhibit pronounced cytotoxicity and can be used in biomedical applications.

This study addresses the gap in research on the application of thermochromic polymers (TPs) in food packaging and their potential for real-time temperature monitoring, aiding in the assessment of food quality and shelf-life. TPs exhibit a visible color change in response to temperature varia-tions. A comprehensive systematic review (SR) across multiple engineering peer-review databases using predefined terms was conducted. Additionally, international patent databases were inves-tigated using the same predefined terms. Independent experts reviewed the methodology to identify and address potential biases. A total of 288 eligible articles and 922 patents were identified. After a duplicate selection and extraction process according to the inclusion criteria, four related full-text publications were selected from the initial 288 articles, and five relevant patents were selected from the 922 patents. The qualitative review suggests that TPs hold significant promise as food packaging materials due to their unique physical properties. The study concludes that TPs offer valuable properties for the food packaging industry, meriting further investigation to exploit their benefits fully.

Side-chain liquid crystal polymers have been mixed with ferromagnetic particles, and the for-mation of a monodomain in magnetic fields studied. At relatively low concentrations, the presence of ferroparticles substantially speeds up the rate of formation of a monodomain with the magnetic field and at a given concentration of ferrofluid that rate is independent of the magnetic field strength. In this way, rapid formation of a monodomain is possible at magnetic field strengths far lower than required for the liquid crystal polymer alone. This is anticipated to very helpful in the fabrication of devices based on monodomain liquid crystal elastomers. Wide angle x-ray scattering has been used to monitor the formation of the monodomain and small angle x-ray scattering can give some indication of the ferroparticle behaviour. A model is developed to explain the behaviour. The alignment properties of the ferroparticles is related to their ability to form chains under the influence of very low magnetic fields; these chains are of relatively low stability and may become disrupted after long times, high magnetic fields, or high concentrations. In general, the best results for alignment were at volume fractions below 1%, and under these con-ditions there is the potential for producing monodomain samples with improved properties; in particular shape changes with temperature are significantly larger as a result of improved backbone orientation. Experiments involving monodomain formation and director realignment suggest that the presence of ferroparticles results in a modification in the mechanism for alignment development driven by the organisation of the polymer backbone as a consequence of the con-straints offered by the morphology of the chains of ferroparticles.

Synthetic bone made of calcium phosphate is widely used for the clinical treatment of bone defects caused by trauma and bone tumors. Although synthetic bone is easy to use, its effects are only partial depending on the size and location of the bone defect, and there are many treatment options other than the use of synthetic bone. Various biodegradable polymers that are being considered for use as scaffolds for regenerative medicine are also being considered for use as synthetic bones; however, commercial synthetic bone products with performance comparable to that of calcium phosphate bioceramics have not yet been clinically applied. This review introduces the practice of bone regeneration therapy with synthetic bone and recent research on bone regeneration therapy with biodegradable polymers.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The illicit use of fentanyl has led to hundreds of thousands of opioid-related deaths worldwide. Therefore, the detection of fentanyl by law enforcement and recreational users is of utmost importance. However, current detection methods are expensive, time-consuming, require special storage conditions and necessitate complex instrumentation that is generally unportable and requires skilled personnel to operate. An alternative approach would be using molecularly imprinted polymers (MIPs) as the recognition component of a handheld sensor, testing strip, or color-based assay. In this work, a molecularly imprinted polymer was made by using methacrylic acid (MAA) and ethyleneglycol dimethacrylate (EGDMA) as the functional monomer and cross-linking monomer respectively, and benzylfentanyl (Bfen) as the template. The use of benzylfentanyl is advantageous because it closely resembles the structure of fentanyl but does not have any physiological effects as a narcotic. Important studies herein determined the optimum ratio of the template:functional monomer, with subsequent evaluations of selectivity versus the commonly encountered narcotics such as heroin, cocaine, and methamphetamine. The data obtained from the HPLC analysis showed that the Bfen-MIP was successful in selectively binding the template and actual fentanyl, better than other common narcotics.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

Polymers in highly confined geometries can display complex morphologies including ordered phases. A basic component of a theoretical analysis of their phase behavior in confined geometries is the knowledge of the number of possible single-chain conformations compatible with the geometrical restrictions and the established crystalline morphology. While the statistical properties of unrestricted self-avoiding random walks (SAWs) both on and off-lattice are very well known, the same is not true for SAWs in confined geometries. The purpose of this contribution is a) to enumerate the number of SAWs on the simple cubic (SC) and face-centered cubic (FCC) lattices under confinement for moderate SAW lengths, and b) to obtain an approximate expression for their behavior as a function of chain length, type of lattice, and degree of confinement. This information is an essential requirement for the understanding and prediction of entropy-driven phase transitions of model polymer chains under confinement. In addition, a simple geometric argument is presented that explains, to first order, the dependence of the number of restricted SAWs on the type of SAW origin.

Self-healing, stretchable and moldable hydrogels have a great potential application in tissue engineering and soft robotics. Despite great success in reported hydrogels, it is still a great challenge to construct the moldable hydrogels with an ultrafast self-healing performance. Herein, the dynamic double network (DN) composite hydrogels (PBLH) with ultrafast self-healing, stretchable and moldable were successfully constructed by poly (vinyl alcohol) (PVA), borate, ε-poly-L-lysine (EPL) and hyaluronic acid (HA) based on an efficient one-pot method. Fourier transform infrared spectroscopy, X-Ray diffraction and rheological measurements confirmed the formation of dynamic double networks among PVA, B, EPL and HA through the cross-linking of dynamic borate bonds, electrostatic interaction and hydrogen bonding. Having fabricated the dynamic double network structure, the damage gap of the composite hydrogels can heal within 1 min, presenting an excellent self-healing ability. Simultaneously, the DN hydrogels can be molded to various shapes and the length of the DN hydrogels can be stretched to 15 times than original length. In addition, the DN hydrogels exhibited an excellent antibacterial property against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). Our results illustrated that the DN composite hydrogels not only retain the advantages of traditional hydrogels, but also possess ultrafast self-healing, outstanding stretchable and antibacterial properties, presenting a prospective candidate for constructing biomedical materials.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

The local and global order in dense packings of linear, semi-flexible polymers of tangent hard spheres are studied by employing extensive Monte Carlo simulations at increasing volume fractions. Chain stiffness is controlled by a tunable harmonic potential for the bending angle whose intensity dictates the rigidity of the polymer backbone as a function of the bending constant and equilibrium angle. The studied angles range from acute to obtuse ones, reaching the limit of rod-like polymers. We analyze how packing density and chain stiffness affect the ability of chains to self-organize at the local and global levels. The former corresponds to crystallinity as quantified by the Characteristic Crystallographic Element (CCE) norm descriptor, while the latter is computed through the scalar orientational order parameter. In all cases, we identify the critical volume fraction for the phase transition and gauge the established crystal morphologies, developing a complete phase diagram as a function of packing density and equilibrium bending angle. A plethora of structures is obtained, ranging from random hexagonal closed packed morphologies of mixed character and almost perfect face centered cubic (FCC) and hexagonal close-packed (HCP) crystals at the level of monomers, to nematic mesophases, with prolate and oblate mesogens at the level of chains. For rod-like chains, hysteresis is observed between the establishment of long-range nematic order and crystallization, while for right-angle chains both transitions are synchronized. A comparison is also provided against the analogous packings of monomeric and fully flexible chains of hard spheres.

Products made from petroleum-derived plastic materials are linked to many environmental problems such as greenhouse gas emissions and plastic pollution. It is desirable to manufacture products from environmentally friendly materials instead of petroleum-based plastic materials. Products made from biomass-fungi composite materials are biodegradable and can be utilized for packaging, construction, and furniture. In biomass-fungi composite materials, biomass particles (derived from agricultural wastes) serve as the substrate and the fungal hyphae network binds the biomass particles together. There are many reported studies on 3D printing of biomass-fungi composite materials. However, there are no reported studies on biodegradation of 3D printed samples from biomass-fungi composite materials. In this study, two types of biomass materials were used to prepare printable mixture hemp hurd and beechwood sawdust. The fungi strain used was Trametes versicolor. Extrusion based 3D printing was used to print samples. 3D printed samples were left for five days to allow fungi to grow. The samples were then dried in an oven for 4 hours at 120ºC to kill all the fungi in the samples. The samples were buried in the soil using a mesh bag and kept in an environmental chamber at 25℃ with a relative humidity of 48%. The weight of these samples was measured every week over the period of three months. Both types of samples (prepared from beechwood sawdust and hemp hurd, respectively) showed weight change after three months. Furthermore, the samples made from hemp hurd had more weight change than the samples made from beechwood sawdust. The SEM (scanning electron microscope) micrographs and FTIR (Fourier transform infrared) spectroscopy showed evidence of biodegradation of these samples.

Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (&lt;0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

Elastic peak electron spectroscopy, abbreviated EPES, involves ana- lyzing the line shape found in the elastic peak. The reduction in the energy of electrons of the elastic peak is a result of energy transfer to the target atoms, a phenomenon known as recoil energy. EPES differs from other electron spectroscopies in its unique ability to identify hydrogen in polymers and hydrogenated carbon-based materials. This feature is particularly noteworthy because lighter elements exhibit stronger energy shifts. The energy difference between the positions of the elastic peak of carbon and the elastic peak of hydrogen tends to increase as the kinetic energy of the incident electrons increases. If, during electron irradiation of an insulating polymer, the number of secondary electrons emitted by the surface is less than the number of electrons absorbed in the sample, the surface floats energetically until it stabilizes at a potential energy eVs. As a result, the interaction energy changes and modifies the energy difference between the elastic peaks of hydrogen and carbon. In this study, the charge effects are evaluated using the Monte Carlo method to simulate the EPES spectra of electrons interacting with polystyrene and polyethylene.

There have been many researches on the surface acoustic wave (SAW) sensors for detecting sulfur-containing toxic or harmful gases. This paper aims to give an overview of the current state of the polymer films used in SAW sensors for detecting deleterious gases. By covering most of the important polymer materials, the structures and types of polymers are summarized, and a variety of devices with different frequency, such as delay lines and array sensors for detecting mustard gas, hydrogen sulfide and sulfur dioxide are introduced. The preparation method of polymer films, the sensitivity of the SAW gas sensor, the limit of detection, the influence of temperature and humidity, and the anti-interference ability are discussed in detail. The advantages and disadvantages of the films are also analyzed, and the potential application of polymer films in the future is also forecasted.

Thermal shape memory polymers (SMPs) find increasing applications in biology and medicine due to their promising potential for improved biocompatibility. In such applications, the inevitable penetration of small molecules from the ambient fluid into the polymer influences the shape recovery process and often leads to a reduction of the temperature, at which shape recovery takes place. We show here via molecular dynamics simulations that the size of additive molecules plays a key role for this process. While the effect of concentration on the recovery rate is monotonic in the investigated range, a non-monotonic dependence on the size of additive molecules emerges at temperatures close to the glass transition. This work thus identifies the additives’ size to be a qualitatively novel parameter for switching the recovery process in polymer-based shape memory materials.