Based on the previous work done by Fujii et al., NdBaInO4 compounds present modest oxide-ion conductivities. Therefore, it has been an attractive system of significant interest. In this paper, the Ca element has been attempted to partially substitute for Nd and the total electrical conductivity has been successfully improved due to the generation of oxygen vacancies. The synthesis, crystal structure, density, surface topography and electrical properties of NdBaInO4 and Ca-doped NdBaInO4 have been studied respectively. NdBaInO4, 10% and 20% molar fraction of Ca doped NdBaInO4 were synthesized through solid state reaction and they were calcined at 1000 °C for 14 hours and sintered at 1440 °C,1430 °C and 1420 °C respectively. The crystal structure of them has been obtained from Le Bail refinement of the XRD pattern, giving the result of the monoclinic structure which belongs to P21/c space group. The size of particles processed with different ball milling time and surface topography have been detected by the scanning electron microscope. The total electrical conductivities of Nd1-xCaxBaInO4-x/2 (x = 0, 0.1 and 0.2) were measured in the dry atmosphere by AC impedance spectroscopy and Nd0.9Ca0.1BaInO3.95 exhibited the highest total electrical conductivity and the lowest activation energy. What is more, the total conductivity of Nd0.9Ca0.1BaInO3.95 in the wet atmosphere at moderate temperature is relatively higher than that in the dry atmosphere while this phenomenon was not found in NdBaInO4. Therefore, the excess conductivity suggests that potential proton conduction may exist in wet atmospheres. In addition, Ca-doped NdBaInO4 were chosen for the oxygen isotope exchange which aims to obtain the diffusion coefficient and surface exchange coefficient, and Nd0.9Ca0.1BaInO3.95 shows the highest diffusion coefficient and D* decreases with the increase of the molar fraction of the Ca element.

Introduction: To indentify the most effective actors(authors, countries, and journals) about composite resin restorations in the period 2000-2020.Material and Methods: An electronis research was conducted in the Scopus database by selecting the words ‘composite resin’ and ‘restoration and English language, article and review types, dentistry field. Their bibliometric data including publication title, authorship, citation count, citation dentistry, year of publication, country and institution of origin, journal of publication, study design, and keywords were extracted and analyzed.Results and Discussion: To our knowledge, this is the first bibliometric article on composite resin restorations. This study provides information about authors, institutions and countries that contribute to significant improvements in composite resin restorations. From 2000 to 2020, there were 7118 articles published from 99 countries.Articles originate primarily from the USA and Brazil. Results indicate that the USA, Brazil, Germany, Turkey, the United Kingdom, Japan, Swtizerland, Italy, Netherlands and India are the leading countries in composite resin restoration research and account for 51.8% of the total number of publications. The total number of citations are 158.404, corresponding to 22 citations per paper publication. During the time period examined, 776 hot articles and 228 classic articles on composite resin restorations were found.The journal with the most publications is ‘Operative Dentistry’. The publishing houses of the top 10 journals are from 4 countries: USA(6),Netherlands(2),Germany(1),Japan(1). The most cited article within the boundaires of this study is Ferracane’s article titled ‘Resin composite-State of the art’, which was published in Dental Materials in 2011 and received 913 citations.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

The aim of this study was to investigate the effect of laser irradiation to computer-aided de-sign/computer-aided fabrication (CAD/CAM) resin blocks coated with a silane coupling agent on the bond strength between the resin blocks and composite resin. The CAD/CAM resin blocks used in this study were Cerasmart 300 (GC) and Vita Enamic (Vita); they were cut into plates and then subjected to a series of treatments. After processing with a silane coupling agent, treatment with a semiconductor laser was performed at 3.0, 5.0, and 7.0 W, followed by the bonding procedures. The control group included those exposed to silane and bonded without laser application. After bonding, a mold with a simulated cavity was formed on the specimen and filled with flowable composite resin, and they were stored for 24 h or stressed by thermal cycling for subsequent testing that assessed the shear bond strength (n = 10). The results revealed that the bond strength was significantly enhanced by laser irradiation after applying a silane coupling agent, whereas significant effect was not detected between the materials. Particularly, 7 W laser irradiation had a significant effect on the bond strength between the composite resin and Cerasmart block after thermal cycling.

Purpose: This study aimed to evaluate the nanomechanical properties and chemical composition of restorative materials and dental surfaces using different toothpastes. Methods: Enamel (n=60) and dentin (n=60) bovine blocks were obtained and restored using resin-modified glass ionomer cement (RMGIC, n=30) or composite resin (CR, n=30) to form the dentin adjacent to RMGIC (DRMGIC), enamel adjacent to RMGIC (ERMGIC), dentin adjacent to CR (DCR), and enamel adjacent to CR (ECR). After restoration, one hemiface of each specimen was coated with an acid-resistant varnish to create the control (C) and eroded (E) sides (erosion: 5 days, 4 × 2 min/day; 1% citric acid / abrasion: 2 × 15 s followed by immersion on slurries 2 min). Three toothpastes were used: without fluoride (WF; n=10), sodium fluoride (NaF; n=10), and stannous fluoride (SnF2; n=10). The specimens were analyzed for nanohardness (H), elastic modulus (Er), and chemical composition using energy-dispersive X-ray spectroscopy (EDS) and Raman microscopy. Data were analyzed using ANOVA two-way repeated measures and Tukey’s test (α = 0.05). Results: The NaF presented lower values of H for DRMGIC-C, with a statistical difference for WF (p < 0.05). SnF2 resulted in lower Er values for ERMGIC-E and RMGIC-E than WF and NaF (p < 0.05). WF showed lower calcium and phosphorus concentrations for DCR-E than other types of toothpastes (p < 0.05). Only stannous-based toothpaste damaged the elasticity of eroded glass ionomer restorations performed in enamel. Toothpastes with fluoride was capable for maintaining main chemical elements of dentin adjacent to restorative materials under challenge conditions.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Hybrid materials are a recent addition in the field of Restorative Dentistry for computer-assisted design/ computer-assisted manufacturing (CAD/CAM) indirect restorations. The long–term clinical success of modern dental restorative materials follows a multifactorial pattern. Among the characteristics, affecting the longevity of a restoration, mechanical properties and physicο – chemical interactions are of utmost importance. While numerous researchers constantly evaluate the mechanical properties, the biological background of resin–based CAD/CAM biomaterials is scarcely investigated and, therefore, less described in the literature. This review aims to analyze the biofilm formation on the surfaces of novel hybrid, resin–based CAD/CAM materials and evaluate the methodological protocols followed to assess microbial growth. It is demonstrated that the surface structure, the composition and the finishing and polishing procedures on the surface of a dental restorative material influence the initial bacterial adhesion; however most studies focus on in vitro protocols, whereas in vivo and/or in situ research of microbiomics in CAD/CAM restorative materials is lacking, obstructing in that manner the accurate understanding of the bioadhesion phenomenon in the oral cavity.

Tooth decay, also known as caries, is a significant medical problem that harms teeth. Treatment is based on the removal of the carious material and then filling the cavity left in the tooth, most commonly with amalgam or composite resin. The consequences of filling failure include repeating the filling, or performing another treatment, such as a root canal, or extraction. Dental amalgam contains mercury, and there is a global effort to reduce its use. However, no consensus has been reached using randomized clinical trials, regarding whether amalgam or composite resin materials are more durable, and which is the best restorative material. To determine which material is superior, we performed a retrospective cohort study using a large database where members of the 58 dental clinics with 440 dental units were treated. The number of failures of the amalgam compared to composite resin restorations between 2014 and 2021 were compared. Our data included information from over 650,000 patients. Between 2014 - 2021, 260,905 patients were treated. 19,692 out of 113,281 first amalgam restorations failed (17.49%), whereas significantly fewer composite restorations failed (11.98%) 65,943 out of 555,671. This study indicates that composite is superior to amalgam and therefore it is reasonable to cease using mercury containing amalgam.

In this study, the impact of the addition of high-aspect-ratio nano-ettringite to photocurable epoxy acrylate resin was explored, with a specific focus on the changes observed in viscosity, shrinkage, tensile strength, and elongation at the break of composites formed. Herein, the nano-ettringite samples were modified using KH-570. The 3 wt% or 6 wt% KH-570-modified and unmodified nano-ettringite were dispersed into the resin by ultrasonic treatment in conjunction with mechanical stirring. The grafting effects of nano-ettringite onto KH-570 were analyzed through scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric (TG) analysis, and Fourier transform infrared spectroscopy (FTIR). The results demonstrate that increased dosages of unmodified and modified nano-ettringite led to increased viscosity of the composite while reducing shrinkage. At the same dosage, the photocurable resin with modified nano-ettringite demonstrated a lower shrinkage and a higher tensile strength. Notably, when the amount of modified nano-ettringite was 3 wt%, the highest tensile strength of the composite was 64.61 MPa, presenting a 72.57% increase compared to the blank sample. Furthermore, the incorporation of modified nano-ettringite as a filler provides a new perspective for improving the performance of photocurable epoxy acrylate resin composites.

The objective of this study was to detail the monomer composition of resin-based dental materials sold in the market in 2023 and to evaluate the proportion of BPA derivatives in relation with their applications. A search on manufacturers’ websites was performed to reference resin-based dental materials currently on the market. Their monomer composition was determined from material safety data sheets and completed with a search on PubMed database. Among the 543 material compositions exploitable, 382 (70.3%) contained BPA derivatives. Among them, 56.2% contained BisGMA, 28% BisEMA, the most frequently reported. A total of 59 monomers of which 6 BPA-derivatives were found. 309 materials (56.9%) contained UDMA and 292 (53.8%) TEGDMA. Less than one third of materials identified contained no BPA derivatives. These proportions vary a lot depending on their applications with materials dedicated to dental care of young populations containing the highest proportions of BPA-derivatives monomers. The long-term effects on human health of the different monomers identified including BPA-derivatives monomers is a source of concern. For children and pregnant or lactating women arises the question to take a precautionary principle and avoid the use of resin-based dental materials likely to release BPA by opting for alternative materials.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Immobilization of enzymes is a good field of study to expand the life of enzyme in and lowering the cost of the chemical processes such as separation processes. Urease is an important enzyme with medical and industrial applications. The aim of the present study is to prepare an immobilized urease on a strong cation exchange resin (Amberlite IR120 -Na) and study of its activity and stability. We monitored the liberation of Na ions in the collected fractions and searching for protein in the fractions as an indicators of immobilization by ion exchange phenomenon. Sodium is measured using atomic absorption spectroscopy techniques, while protein tested by Bradford’s method. Immobilized urease activity was evaluated by salicylate-hypochlorite method. The results indicated a complete immobilization of urease enzyme on the resin surface with reserving 92% of the activity of free enzyme. The immobilized urease enzyme on resin showed good stability and it has a 62% of its activity after 154 days of storage at room temperature. It is concluded that a new immobilized urease enzyme system is prepared with good enzyme activity and stability.

The crosslinking behavior of polyethylene (PE) determines its exceptional performance and application. In this study, we investigated the crosslinking behaviors of different PE resins through model simulation and rheological methods. Specifically, the mathematical equation of "S" model was established for PE resin. According to this equation, the optimal maximum gel content for high-density polyethylene (HDPE) was found to be around 85%. Moreover, the maximum crosslinking degrees for different PE resins depended largely on their density and molecular weight. The melt viscosities before crosslinking in PE resins were highly influenced by their melt index. The higher melt indexes resulted in the lower storage moduli, improving melt processability during processing. In addition, the crosslinking rates of PE resins were strongly influenced by peroxide concentration, independent of PE resin structures. For high molecular weight and low-density PE resins, they exhibited decreased ti values, increased A0 values, and decreased k6 values. However, there were no noticeable variations in the values of k2 and phi among different PE resins. And all simulated modeling outcomes showed the remarkable consistency with the experimental rheological data. These findings are of utmost significance in the industrial manufacture of PE resin.

Nano-titanium has excellent corrosion resistance and can be widely used in the field of corrosion resistant coatings. This paper introduces nano-weight titanium modified phenolic resin coatings and their anti-corrosion properties to explore the principle of nano-titanium modification and the mechanism of anti-corrosion to further develop more advanced corrosion resistant coatings. The article uses scanning electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and UV-Vis spectrophotometer to characterise the morphology and structure of the nano-titanium modified phenolic resin coatings and to determine the corrosion resistance properties of the modified phenolic resin coatings. The results show that the 4% nano-titanium modified phenolic resin coating, nano-titanium powder and phenolic resin will maximize the dispersion and combination, and the structure is good; nano-titanium grafted on phenolic resin, the successful preparation of nano-titanium modified phenolic resin; modified nano-titanium added to improve the coating's ability of UV absorption. The corrosion resistance of the coating is much better than that of the unmodified phenolic resin coating.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (&lt;0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

In this present study, 3-pentadecyl-phenol was selected as a modifier to prepare a foamable phenolic resin with excellent performance, which was successfully prepared by in-situ modification. Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance (¹H NMR, ¹³C-NMR) were used to test and characterize the molecular structure of the modified resin. The results showed that 3-pentadecyl-phenol successfully modified the molecular structure of phenolic resin with a reduction in resin gel time. The effect of changing the added amount of 3-pentadecyl-phenol on the mechanical properties, microstructure and flame retardancy of the modified foam was investigated. The results showed that when the amount of added 3-pentadecyl-phenol was 15% of the total amount of phenol, this resulted in the best toughness of the modified foam, which could be increased to 300% compared to the bending deflection of the unmodified phenolic foam. The cell structure showed that the modified phenolic foam formed a more regular and dense network structure and the closed cell ratio was high. Furthermore, the compressive strength, bending strength, and limited oxygen index were improved, while the water absorption rate was lowered. However, the foam density could be kept below 40 mg/cm³, which does not affect the load.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Commiphora molmol myrrh resin extracts, which have different physical properties such as polarity and dielectric constant, were prepared by immersion in extraction solvents (hot water, DMSO, hexane, ethanol, and methanol). Methanolic myrrh resin extracts showed broad antibacterial activity against isolated airborne bacteria. Furanoeudesma-1,3-diene and curzerene, as the main terpenoids in the methanolic myrrh resin extract, were analyzed using GC-MS, and the methanolic myrrh resin extracts were found to have antiviral activity (81.2% viral RNA inhibition) against H1N1 influenza virus. Biochars (wood powder-and rice husk-derived) coated with myrrh resin extracts also showed antiviral activity (22.6% and 24.3% viral RNA inhibition), due to the adsorption of terpenoids onto biochar. Myrrh resin extract using methanol as the extraction solvent is a promising agent with antibacterial and antiviral efficacy, and it can be utilized as a novel material via adsorption onto biochar for air filtration processes, cosmetics, fertilizers, drug delivery, and corrosion inhibition.

To develop a lower-cost, excellent performance, and environmentally friendly phe-nol-formaldehyde (PF) resin, soybean meal was used to modify PF resin, and soybean meal-phenol-formaldehyde (SMPF) resins were prepared. Their physicochemical properties and curing performance were investigated, showing that SMPF resins have higher curing tempera-tures than PF resin. The Fourier transform infrared spectroscopy (FTIR) results indicated that the cross-linking reaction occurred between the amino groups of soybean protein and the hy-droxymethyl phenol. Moreover, with the addition of soybean meal, the viscosity of SMPF in-creased while the gel time decreased. It is worth mentioning that SMPF-2 resin has favorable viscosity, short gel time, low curing temperature (135.78 °C), and high water resistance and bonding strength (1.01 MPa). Finally, all the plywoods bonded with SMPF resins have good water resistance and bonding strength, which could meet the Standard (GB/T 17657-2013, type I) for plywood. The optimized SMPF resins showed the potential application to replace part of PF resin in the wood industry.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

Polyurethane (PU) foam adhesives were prepared from castor oil as a polyol with isocyanate poly (4,4′-methylene diphenyl isocyanate) (PMDI) using a solvent-free process. The NCO/OH molar ratio used for the preparation of PU foams was 1.5. Water, organosiloxane and dibutyltin dilaurate were blowing agent, surfactant and catalyst, respectively. Effects of the ratio of blowing agent and catalyst were adjusted to optimize the properties. The results show that 4 wt% of castor oil of catalyst and blowing agent minimizes water absorption and maximizes volume expansion in the PU foams. FT-IR analysis shows that urethane bond was formed by hydroxyl group of castor oil and –NCO group of isocyanate PMDI. More blowing agent and catalyst could improve the volume expansion ratio and reduce water retention of PU foams. It was found that Moso bamboo charcoal (Phyllostachys pubescens) or/and China fir wood particle (Cunninghamia lanceolate) composites with setting densities of 500 and 600 kg/m³ can be prepared from optimized castor oil-based PU foam adhesive at 100 °C for 5 min under a pressure of 1.5 MPa. Increasing the amount of bamboo charcoal decreases the equilibrium moisture content, water absorption and internal bonding strength of the composite. Notably, bamboo charcoal composite exhibits excellent dimensional stability. The optimized density and bamboo charcoal percentages of the composite were 500 kg/m³ and 50 to 100%. The castor oil-based PU composites containing bamboo charcoal fulfilled the CNS 2215 standards for particleboard. This dimensionally stable, low-density bamboo charcoal composite has high potential to replace current indoor building materials.

The aim of this study was to using a lignin based resin (LB) to improve the performance of the soy flour based adhesive. Soy flour (SF), polyamidoamine-epichlorohydrin (PAE), LB was used to develop a plywood adhesive. The solid content and viscosity of the adhesive, functional groups, thermo-stability, and crystallinity of the cured adhesive were characterized and the performance of the resultant adhesive was evaluated by fabricating three-ply plywood. Results showed using LB and PAE mixture to modify SF adhesive improves dry and wet bond strength by 66.3 and 184.2%. PAE contributed more for the wet bond strength improvement and the LB contributed more for the dry bond strength. The improvement was attributed to: 1) LB/PAE reacted with the functions of the soy protein and form a cross-linking network; 2) Polycondensation reaction between LB molecules further improved crosslinking density of the adhesive and formed a interpenetration structure with crosslinked protein; 3)The easy penetration of LB on wood surface and formed more interlock with wood. The denser structure created by LB and PAE mixture improved the thermal stability and decreased the crystallinity of cured adhesive. The usage of the LB and PAE mixture increased solid content by 35.5%, meanwhile, makes its viscosity acceptable for the industrial application.

Shell nacre from Pinctada species has been extensively researched for managing bone defects. However, there is a gap in the research on using shell nacre as cement with improved physico-chemical properties. To address this, the current study aimed to develop a chemical curable com-posite shell nacre cement (SNC) using shell nacre powder and an organically modified ceramic resin shell nacre containing ladder-structured siloxane methacrylate (SNLSM). Different amounts of shell nacre (24, 48, and 72 weight(wt)%) were added to the SNLSM resin matrix and the effect on the physicochemical properties of the cement was studied. The composite shell nacre cement SNC 72 containing 72 wt% shell nacre exhibited significantly higher mechanical properties (com-pressive strength >100 MPa, flexural strength > 35 MPa) and low linear polymerization shrinkage (0.4%) than other compositions. SNC 72 was radiopaque and the exotherm generated during the curing of the cement was minimal. Direct contact of cured SNC 72 with L929 cells revealed the non-cytotoxic nature of the cement. Overall, the results of the study proved that the composite SNC 72 would be a promising candidate for bone defect management.

In this study, the properties of unsaturated polyester resin were studied in the presence of recycled ceramic waste particles. Herein, composites were created that contained 28.5-50 wt% porcelain particles (particle size <180 µm). High filler contents increased the gel time and decreased the exotherm temperature of unsaturated polyester resin during curing. The obtained results showed that physical parameters, such as the resin density and porosity, increased as the filler content increased. In addition, the X-ray diffraction results indicated that the produced samples were a combination of ceramic waste particles and unsaturated polyester resin, resulting in semi crystalline structure. The results showed that the maximum water absorption at 40°C increased from 0.97 to 1.5% as the filler content increased from 28.5 to 50 wt%; in this process, the materials experienced a color change but did not lose mechanical performance. Finally, the samples were characterized by thermogravimetric analysis (TGA) to study the effect of porcelain powder on the thermal degradation of the resin. The TGA scans were analyzed with the Friedman method. The results indicated that the samples with porcelain powder exhibited substantially better thermal stability than unsaturated polyester resin.

Asphalt cement will not last for a long time as the world encounters a diminishment in the crude oil. For sustainable, flexible pavement development, new resources can provide a contribution to replace it partially or entirely. In this study, asphalt was partially and entirely replaced by guayule resin as a bioresource by-product, extracted during the guayule natural rubber production. Crumb rubber modifier (CRM) was used as an asphalt enhancer. The Superpave grading system was followed at high, intermediate, and low temperatures to evaluate such innovative binder for rutting, fatigue, and thermal cracking, respectively, in addition to viscosity. Therefore, the original, short-term aging and long-term aging were simulated using tank, rolling thin film oven, and pressure aging vessel materials. Additionally, component analysis using Fourier-transform infrared spectroscopy was provided to link the rheological properties with the chemical changes. Outcomes showed a relatively much lower viscosity of guayule in the same high-temperature asphalt grade indicating savings in plant energy consumption and reduced environmental emissions. CRM enhanced guayule, but not as much as asphalt, proven by polymeric component migration through liquid binder. This enhancement was reflected in the rheological performance besides other factors. As-received guayule seems to have high oxygen content proven by strong absorption peak intensities of oxidative bonds (e.g., Carbonyl and sulfoxide). Such pre-oxidation was negatively reflected in the intermediate- and low-temperature performance of guayule and guayule-based binders. However, the investigated guayule had potential to compensate for asphalt replacement in the presence of CRM by 23–42% by weight of blend.

This paper presents the results of laboratory tests of CFRP (carbon fibre-reinforced polymer) laminates, which allowed the development of numerical material models. The obtained data were used in a further stage to perform numerical simulations of four variants of medical tabletops differing, among other features, in the shape of the cross-section. Maximum deflections and effort in the composite material were analyzed. The final step was to perform a laboratory test for one of the tabletop versions, the results of which confirmed the correctness of the numerical calculations. This work is aimed at both researchers and designers involved in the practical application of fibre-reinforced polymer matrix composites.

In order to improve the performance of soft plantation wood, an environmentally friendly inorganic-organic hybrid wood modifier was developed. First, using urea and melamine as crosslinking agents, the waterborne glucose silicone resin (MUG) was prepared with glucose under the catalysis of inorganic acid and metal ions. Then MUG resin was diluted to 10% and 20% mass fraction, and compounded with sodium silicate (S) of 20% and 10% mass fraction, so the inorganic-organic hybrid G10S20 and G20S10 wood modifier were obtained respectively. Then plantation poplar wood (Populus tomentosa) were impregnated and modified with them. Their physical and mechanical properties were tested and compared with those of the wood treated with S of 20% mass fraction (S20). Infrared analysis showed that amino resin characteristic structure (CO-NH-) existed in MUG resin. The resin has good permeability. Compared with S20 modified wood, the degree of shrinkage of G10S20 or G20S10 modified wood is reduced, their moisture absorption is reduced, and their dimensional stability is improved. Waterborne glucose silicone modifier can effectively improve the wood density, modulus of elasticity, modulus of rapture and compression strength. SEM analysis showed that the cell wall of G20S10 modified wood was significantly thicker than the untreated wood, and there were columnar and granular solid substances attached in some cell cavities, ducts and corners, etc. EDX showed that the number of Si elements on the cell wall was significantly increased compared with the control, indicating that the modifier effectively entered the wood cell wall. The waterborne glucose silicone resin can greatly improve the physical and mechanical properties of wood through organic-inorganic hybridization. It is a green, non-formaldehyde, eco-friendly, low cost, compound wood modifier with broad application prospects.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

In this study, the effect of ZnO nanoparticles (Zn NPs) on the performance of epoxy resin composites was investigated. The new ZnO/epoxy resin composites were synthesized using halloysite nanotubes (HNT) and different types of ZnO nanoparticles (commercial ZnO and ZnO-ODTES). These ZnO nanoparticles were utilized for intending to enhance the interfacial bonding between the epoxy resin and the reinforcement. Various methods such as FTIR, TGA, DSC, TEM-EDX, and Nanoindentation analyses were used to prove that the ZnO nanoparticles can improve the properties of epoxy resin composites. The thermal properties of the epoxy resin composites were enhanced to a greater extent by the addition of ZnO NPS. DSC testing proved that the epoxy resin composites modified with ZnO NPS are more flexible and elastic than unmodified epoxy resin. It was seen that the epoxy resin modified with ZnO-ODTES shows a much improved hardness and penetration depth compared to the other samples. These findings can pave the way for the developing of ZnO-based marine coatings with improved properties.

In this study, cotton fabric reinforced phenolic resin (CPF) composites were modified by adding four two-dimensional fillers: graphitic carbon nitride (g-C3N4), graphite (Gr), molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN). The tribological properties of these modified materials were investigated under dry friction and water lubrication conditions. CPF/ Gr composite exhibits significantly better tribological performance than the other three fillers modified CPF composites under dry friction, with a 24% reduction in friction coefficient and a 78% reduction in wear rate compared to unmodified CPF composite. Under water lubrication conditions, all four fillers did not significantly alter the friction coefficient of the CPF composite. However, except for an excessive amount of Gr, the other three fillers can reduce the wear rate. Particularly, in the case of 10% MoS2 content, the wear rate decreased by 56%. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed for the analysis of the morphology and composition of the transfer films. Additionally, molecular dynamics (MD) simulations were conducted to investigate the adsorption effects of Gr, MoS2, and PF on the counterpart surface under both dry friction and water lubrication conditions. The difference in the adsorption capacity of Gr and MoS2 on the counterpart, as well as the resulting formation of transfer films, accounts for the variation in tribological behavior between CPF/Gr and CPF/MoS2 composites. By combining the lubrication properties of MoS2 and Gr under dry friction and water lubrication conditions, using them as co-fillers can achieve a synergistic lubrication effect.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

Literature revealed the potential of using guayule resin for asphalt cement replacement from the binder’s perspective. However, monitoring guayule resin through binder-aggregate mixture could disclose its performance through field. In this study, designated binders were employed to investigate the applicability of such an innovative replacer through mixture, which were neat asphalt and guayule-based binders (neat guayule, asphalt-rubber-guayule, guayule-rubber binders). Consecutively, field-simulated lab mixtures were prepared to investigate the major distresses. Moisture damage, rutting, fatigue cracking, and thermal cracking resistances were investigated using the modified Lottman (TSR) test, rut test by asphalt pavement analyzer (APA), semi-circular bending (SCB) test, and disk-shaped compact tension (DCT) test, respectively. Additionally, the Hamburg wheel-tracking (HWT) test was employed to evaluate moisture susceptibility and rutting resistance. Outcomes revealed that the neat guayule was susceptible to moisture damage at a 7% air content (V_a) when the TSR test was employed. In contrast, all investigated mixtures yielded perfect performances against moisture susceptibility under the HWT test. Guayule-based mixtures perfectly resisted rutting, as analyzed by the rut test and HWT test. Generally, changing parameters (e.g., V_a, rubber addition, and partial asphalt replacement by guayule and rubber) enhanced the guayule-based mixture resistance to rutting and moisture damage resulting in acceptable performances. Guayule-based mixture had a high fracture toughness at low temperatures, hence fatigue fracture resistance at intermediate temperatures. Neat guayule mixture with or without rubber addition did not entirely resist thermal fracture. However, partial asphalt replacement by guayule and rubber resisted the thermal fracture to a great extent.

The nanocomposites with reversible cross-linking covalent bonds were prepared by reacting furfurylamine (FA)-modified diglycidyl ether of bisphenol A (DGEBA) and furfuryl-functionalized aniline trimer-modified graphene (TFAT-G) with bismaleimide (BMI) via Diels-Alder (DA) reaction. The successful synthesis of the TFAT modifier is confirmed by NMR hydrogen spectroscopy and IR spectroscopy tests. The structure and properties of TFAT-G epoxy nanocomposites are characterized by SEM, DSC, tensile and resistivity CES. The results show that TFAT-G was uniformly dispersed in the resin, and 1wt% TFAT-G composites increase to 233% for tensile strength, 63% for elongation at break, 66.1% for modulus and 7.8℃ for Tg. Overall, the graphene/self-healing resin nanocomposites have both good self-healing function and electrical conductivity by adding 1% modified graphene and still maintain the original 83% strength and 89% electrical conductivity after one cycle of heating repair.

Repairing of small and isolated delamination area in carbon fiber reinforced polymer (CFRP) without significantly altering the composite structure is studied in this research. A small drilled hole was introduced at the center of the delamination section of CFRP, providing the channel for epoxy infill of sharp delamination cracks. The pressureless infill repair was achieved through the capillary action of an acetone-diluted resin solution (without hardener) with CNT reinforcement, e.g., 89 m/m% of acetone, 10 m/m% of resin and 1m/m% of CNT. Such an acetone-rich resin pre-coating (RPC) solution is easy to prepare and apply to the drilled hole area. Curing of CNT-toughened resin infill was induced by filling the small-drilled hole with a resin-hardener mixture toughened by CNT/Aramid pulp. The effectiveness of delamination repair with curing periods of two weeks and three months were compared. Flexural strength measurements indicated that 77% (potentially 100%) of the restoration was achievable.

This research seeks to interpret the component analysis of an innovative bio-asphalt binder using guayule resin in addition to crumb rubber modifier (CRM) at high concentrations. Such asphalt modification aims to minimize the dependency on virgin asphalt binder and provide new solutions concerning sustainable, flexible pavement industry. Guayule resin is a promising bioresource for asphalt binder replacement. By now, it could be considered a no value byproduct extracted during the guayule natural rubber production. CRM is a recycled material derived from scrap tires. The provided interpretation could help in understanding the asphalt-rubber-guayule interaction mechanism. Fourier transform infrared spectroscopy (FTIR), supported by thermo-gravimetric analysis (TGA), was used to investigate the component analyses of guayule resin composition, asphalt guayule interaction, and asphalt rubber guayule interaction, compared to corresponding asphalt rubber interaction. Additionally, the rheological properties at elevated temperatures were provided to link the microscale properties with the final product performance. The study clarified the distinct carbon and hydrogen compositional elements of guayule resin. Asphalt and guayule resin have similarities in chemical composition and rheological behavior with temperature susceptibility. The asphalt guayule binder had physical interaction. However, when both interacted with rubber, a chemical interaction was attributed, with no difference in rubber dissolution tendency, in asphalt rubber guayule, compared to asphalt rubber. A bio-binder composed of 62.5% asphalt, 25% guayule and 12.5% CRM had the potential to provide rheological properties better than base asphalt. Such behavior was interpreted by a high release of rubber components.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

The article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCC) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound - a commercial epoxy resin, and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

Tree resin, which in addition to its widespread use in industry is also a macroergic component which has not yet been used for energy purposes. The main goal of this work is to determine the energy content of the resin of spruce, pine and larch and wood components – pulp and turpentine. The combustion heats of resin (MJ/kg) from each timber was determined calorimetrically. The energy values of tree resin (&gt;38.0 MJ.kg-1) were 2.2 and 2.4 times higher than that of bleached and unbleached cellulose, the highest value was recorded for the turpentine (&gt;39.0 MJ.kg-1). The best way of resin tapping is the America method, providing 5 kg resin ha-1 yr-1. The resin quantity tapped was raised at least 3 times applying stimulant, its production cost compared to other feedstocks was the cheapest. The tree resin can be applied as a good means to mitigate global warming and consequently dampen climate change. One tonne of tree resin burned instead of coal spares the atmosphere by 5.0 Mt CO2 since it is environmentally neutral. As resin heating values approach to the lower end of ones of liquid hydrocarbon fuels, greater efforts are needed to examine the most efficient energy use of resin.

Nymphaea lotus L. is the medicinal plant that has long been used as food, cosmetic and traditional medicines in Africa and Asia since the ancient time. Its flavonoids and other interesting phytochemical compounds from rhizome, leaf, and the whole flowers have been reported in the previous published researches. However, stamens, which are essential for reproductive functions, may also represent new alternative sources of potential antioxidant flavonoids as investigated in this study. The innovative green chemistry method i.e. ultrasound-assisted extraction (USAE) as well as macroporous resin (MPR) purification procedure were employed in this current research. The optimal ultrasound-assisted extraction condition is 90 % (v/v) aqEtOH with 34.65 khz ultrasonic frequency and 46 minutes of extraction time. Comparing with heat reflux extraction (HRE) conventional method, the significant gain of 1.35 total flavonoids content was obtained using optimized USAE conditions, jumping to 2.80 when this USAE associated with MPR purification. Not only in vitro cell free antioxidant activity of N. lotus stamen extracts, but also in cellulo antioxidant investigation using yeast model showed the same trend to indicate that the best antioxidant flavonoid can be found in USAE coupled with MPR purification. Moreover, the key antioxidant genes expression in yeast model such as SIR2 and SOD2 were also expressed at the highest level in yeast cell treated with the extract from USAE together with MPR purification. Consequently, it can be seen that the USAE combined with MPR purification can help to enhance the flavonoids antioxidant potential of the stamens extract from this medicinal species.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

Abstract composite silver nanoparticles were synthesised using melanin broth and Arabic gum as a reducing and binding agent. The reactions are carried out with water because it is a non-hazardous solvent. The produced composites either had specified diameters (average diameter of 50 nm) with high silver loading or lower loading composites with tuneable morphologies and electrical properties. UV-IR, gamma, and conventional light are used to characterise the synthesised composite silver nanoparticles. Furthermore, measurements are carried out of the dielectric constant, refractive index, energy gap, optical and electrical conductivities, and refractive index coefficients. The silver nanoparticle formation was validated by UV-Vis measurement of the sample, which demonstrated a distinct peak at a wavelength of 420 nm. The characteristics of the composite silver nanoparticles are also quantified using several methods, including XRD, SEM, and particle size analysis.

Metal matrix composite are used in such fields of technology, such as: aerospace, electronics, energy, industry, defense, automotive, aviation, shipbuilding, and more. Composite coatings of ceramic - metals is used primarily to enhance the durability of machine parts. Therefore, new materials are permanently looked for, what has resulted in the past in development of composite materials. The coatings dispersed are consisting of metallic matrix (metals and their alloys) and small non-metallic particles. The deposition of ceramic particles simultaneously with metallic matrix leads often to composite coatings possessing properties much better than those of metallic coating. The nickel and less often, other iron group elements are usually used as a matrix and Al2O3 as tough particles. The welding technology of applying alloy and composite coatings is widely used. The technology of infrasound thermal spraying of metal matrix composite coatings was presented. It is a simple technology and a very useful one in ship machinery regeneration during the cruise craft (e.g. internal combustion engines, torque pumps, separators). The metal matrix composite coatings must undergo finishing due to high surface roughness after application. In the article to used finishing by plastic working and machining of coatings nickel matrix composite was proposed.

A microstructure-based model is developed to study the effective anisotropic properties (magnetic, dielectric or thermal) of two phase particle-filled composites. The Green’s function technique and the effective field method are used to derive theoretically the homogenized (averaged) properties for a representative volume element containing isolated inclusion and an infinite, chain-structured particles. Those results are compared with the FE approximations conducted for the assumed representative volume element. In addition, as a special case, the Maxwell–Garnett model is retrieved when particle interactions are not taken into consideration. We shall also give some information on the optimal design of the effective anisotropic properties taking into account the shape of magnetic particles.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

The unique porous crystal structure of zeolite offers various important utilizations, it is one of the considerations in selecting zeolite at this study as component of composite for restraining noise. It so happens, previous experiments show that banana stem has porous structure, fibrous, high flexibility and can be applied as material for many various products including as component of acoustic material. The combination of both is alleged that it has capability in absorbing noise. This paper presents an investigation on the composite that it was synthesized of Activated Zeolite and Banana Stem Fibre in various weight for determining its sound absorption coefficient alpha (a). Activating natural zeolite was conducted by using 6M HCl in order for enlarging zeolite pores. The sound absorption coefficient was measured in the frequency range between 125 Hz up to 6000 Hz. The results show that the different weight of banana stem fibre as component of the synthesized composite affects the value of alpha and shifts the frequency area.

The objective was to compare the color match and color stability behavior of single and multishade resin-based composites (RBCs) used for direct restorations. This review was conducted according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines. Randomized clinical trials evaluating the shade performance of single-shade RBCs in direct restorations were included. A search of the scientific literature was performed in 5 databases (April 2024). The meta-analysis was performed using RevMan 5.4, calculating the risk difference (RD) and 95% confidence interval (CI) of the dichotomous outcome using a random effects model. Bias was assessed using the RoB 2.0 tool, and certainty of evidence was assessed using the GRADE tool. Four studies with 263 restorations analyzed were selected. The results showed comparable performance between single-shade RBCs and multishade RBCs in terms of color match and color stability over 12 months. Three studies had a low risk of bias with all expected results, and one study had some concerns. The certainty of evidence for color stability was considered low for all follow-up periods due to the small number of events and sample size. According to the United States Public Health Service Evaluation (USPHS) and the World Dental Federation (FDI), there is comparable clinical color performance between single-shade and multishade RBCs over 12 months.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

We give a bilocal field theory description of a composite scalar with an extended binding potential, that reduces to the Nambu–Jona–Lasinio (NJL) model in the pointlike limit. This provides a description of the internal dynamics of the bound state and features a static internal wave-function, ϕ(⃗r), in the center-of-mass frame that satisfies a Schr¨odinger-Klein-Gordon equation with eigenvalues m2. We analyze the “coloron” model (single perturbative massive gluon exchange) which yields a UV completion of the NJL model. This has a BCS-like enhancement of its interaction, ∝ Nc the number of colors, and is classically critical with gcritical remarkably close to the NJL quantum critical coupling. Negative eigenvalues for m2 lead to spontaneous symmetry breaking, and the Yukawa coupling of the bound state to constituent fermions is emergent.

Premature failure and degradation of layers are the main problems for transportation infrastruc-ture. Addressing these issues necessitates implementing structural health monitoring (SHM) for transportation layers. This strategic approach is instrumental in mitigating maintenance expenses, prolonging the operational lifespan, and preventing accidents resulting from abrupt layer col-lapse. To this end, this research investigated the stress/strain and damage detection capabilities of a self-sensing cementitious composite developed for potential utilization in the construction of an intelligent subgrade layer. The prepared self-sensing cementitious composite consisted of 10% cement and hybrid conductive fillers, including multiwalled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) in sand. Initial findings reveal that the electrical resistivity of the composite is significantly affected by the concentration of MWCNTs/GNPs, with a minimum concentration of more than 0.5% needed to achieve a responsive cementitious composite. More-over, the piezoresistive analysis indicates that an increase in the concentration of MWCNTs/GNPs and stress levels leads to an improvement in the stress/strain sensing perfor-mance. When the self-sensing cementitious composite is subjected to equivalent stress levels, variations in the FCR exhibit an increasing trend with decreasing resilient modulus, stemming from a decrease in stiffness due to the increased concentration of MWCNTs/GNPs. Additionally, the EIS analysis demonstrates a contraction for the Nyquist curves under compressive ramp loading prior to failure, followed by the expansion of these curves postfailure. Scanning electron microscopy (SEM) images visually showcase the bridging effects of MWCNTs and the filling ef-fects of GNPs within the composite structure.

This study demonstrates the successful synthesis of Ni/Y2O3 nanocomposite particles through the application of ultrasound-assisted precipitation using the Ultrasonic Spray Pyrolysis technique. The particle size was predicted accurately using a modified equation, and they were collected in a water suspension with Polyvinylpyrrolidone (PVP) as the stabiliser. The presence of the Y2O3 core and Ni shell was confirmed with Transmission Electron Microscopy (TEM) and with electron diffraction. The TEM observations revealed the formation of round particles with an average diameter of 466 nm, while the lattice parameter on the Ni particle’s surface was measured to be 0.343 nm. The Ni/Y2O3 nanocomposite particle suspensions were lyophilized, to obtain a dried material that was suitable for embedding into a Polylactic acid (PLA) matrix. The resulting PLA/Ni/Y2O3 composite material was successfully extruded successfully, so that a 3D printed technology Fused Filament Fabrication could be used further for the production of tensile test tubes. The tensile tests showed that the addition of lyophilised Ni/Y2O3 into the PLA matrix decreased the tensile strength by 21.8 %, while the tensile modulus was not influenced. Dynamic Mechanical Analysis (DMA) showed that the addition of the Ni/Y2O3 particles increased the glass transition temperature by 5 °C, and increased the storage modulus in the glass transition range significantly. These findings demonstrate the potential for utilising Ni/Y2O3 nanocomposite particles in 3D printing applications, and warrant further exploration of their mechanical properties and potential applications in various fields.

Fluorescent hydrogels are promising candidate materials for portable biosensors to be used in point-of-care diagnosis because (1) they have a greater capacity for binding organic molecules than immunochromatographic test systems, determined by the immobilization of affinity labels within the three-dimensional hydrogel structure; (2) fluorescent detection is more sensitive than the colorimetric detection of gold nanoparticles or stained latex microparticles; (3) the properties of the gel matrix can be finely tuned for better compatibility and detection of different analytes; and (4) hydrogel biosensors can be made reusable and suitable for studying dynamic processes in real time. Water-soluble fluorescent nanocrystals are widely used for in vitro and in vivo biological imaging due to their unique optical properties, and hydrogels based on them allow preserving these properties in bulk composite macrostructures. Here we review the techniques for obtaining analyte-sensitive fluorescent hydrogels based on nanocrystals, the main methods used for detecting the fluorescent signal changes, and the approaches to the formation of inorganic fluorescent hydrogels via sol–gel phase transition using surface ligands of the nanocrystals.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Electrospinning polymer fibers for is a well-understood process, primarily resulting in random mats or single strands. More recent systems and methods have allowed for the production of nanofiber yarns (NFY) for ease of use in textiles. This paper presents a method of NFY manufacture using a simplified dry electrospinning system to produce self-assembling functional NFY capable of conducting electrical charge. The polymer is a mixture of cellulose nanocrystals (CNC), polyvinyl acrylate (PVA) and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). When treated with Ethylene Glycol (EG) to enhance conductivity, fibers touching the collector plate align to the applied electrostatic field and grow, twisting together as additional nanofiber polymer is added by the jet. The longer the electrospinning continues, the longer and more uniformly twisted the NFY becomes. This process has the added benefit of reducing the electric field required for NFY production from >2.43 kV cm-1 to 1.875 kV cm-1.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Air pollution is related to the development of people's livelihood. As one of the main pollutants in the air, formaldehyde affects people's physical and mental health. In order to remove formaldehyde and better protect the health of residents, it is very necessary to develop efficient adsorption materials. In this study, a cellulose composite aerogel Microcrystalline Cellulose/ N-(2- aminoethyl) -3- aminopropyl methyl dimethoxysilane (MCC/APMDS) modified by APMDS was explored. The pore volume and specific surface area of the modified aerogel decreased, the average pore diameter increased, and the adsorption capacity of formaldehyde was stronger. The adsorption experiment shows that the sample prepared under the conditions of APMDS dosage of 6 wt%, reaction time of 4 h and reaction temperature of 90℃ has the largest average pore size (14.56 nm) and the largest formaldehyde adsorption capacity (9.52 mg/g). The excellent adsorption of the composite aerogel is due to high porosity and rich active amino groups on the surface. This study provides valuable information for the preparation of adsorption materials with high formaldehyde adsorption capacity for air purification.

The main objective of this work is to study the effects of carbon nanotubes (CNT) on the strength and electrical properties of cement mortar. Molecular dynamic simulations (MDS) were carried out for the mechanical and electrical properties of the cementitious composite and the associated mechanisms. To model the atomic structure of the Calcium-Silicate-Hydrates (C-S-H) gel, tobermorite 11Å was chosen. Single-walled carbon nanotubes (SWCNTs) embedded in tobermorite structure were tested numerically. In particular, the effect of the concentration of CNT in cement paste was studied. An innovative experiment of electrical characterization of a cementitious composite of carbon nanotubes has been developed.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

The accurate prediction of molecular properties such as lipophilicity and aqueous solubility are of great importance and pose challenges in several stages of the drug discovery pipeline. Machine learning methods like graph-based neural networks (GNNs) have shown exceptionally good performance in predicting these properties. In this work, we introduce a novel GNN architecture, called directed edge graph isomorphism network (D-GIN). It is composed of two distinct sub-architectures (D-MPNN, GIN) and achieves an improvement in accuracy over its sub-architectures employing various learning, and featurization strategies. We argue that combining models with different key aspects help make graph neural networks deeper and simultaneously increase their predictive power. Furthermore, we address current limitations in assessment of deep-learning models, namely, comparison of single training run performance metrics, and offer a more robust solution.

Typhoid fever is a major public health burden which causes substantial global morbidity and mortality due to lack of decisive diagnostic protocols. The capacity of commonly use diagnostic test to validate the absence of typhoid fever is controversial. This study explores to evaluate new techniques for typhoid diagnosis and proposed a harmonised suitable standardized composite reference to be adopted. Published peer-reviewed articles indexed in PubMed, MEDLINE and Google scholar were reviewed for hospital-based studies. This study reveals new typhoid diagnostic techniques such as proteomics, serology, Rapid Diagnostic tests (RDTs), transcriptomics, genomics, and metabolomics. 34.4% of the studies use prospective study design. The study result establishes that, Widal test has a moderate diagnostic accuracy with average percentage sensitivity (52.9%), specificity (54%), positive predictive value (PPV) (56.8%) as well as negative predictive value (NPV) (55.6%) when compared with 29.4%, 28%, 29.5%, and 27.8% of Typhidot respectively. The findings showed a statistically significant difference on the sensitivity between Widal and Typhidot t (40) = 2.639, p = 0.012 at p<0.05 using independent sample t-test. When there is no perfect reference standard that has an optimal diagnostic accuracy, the need for a harmonised suitable standardized composite reference is essential. Hence, this study recommends that, peripheral blood culture with established sensitivity of 60% and Widal test with average sensitivity of 52.9% be adopted as a consensus composite reference standard for typhoid fever diagnosis in other to improve confidence in prevalence estimates.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

ZnS-CdS composite nano-powder doped with (0.01 mol %) Cobalt has been collected by a co-precipitation process at 300 K. The sample is characterized by structural, combined spectroscopic methods and magnetic studies. The prepared samples were belonging to cubic structure no impurity phases were observed. Doping of cobalt increase the neighborhood strain assessment and a decreases lattice constants decides from x-ray diffraction data. The crystallite size is 10.42nm. From UV-absorption and EPR studies revealed that the energy band gap of Co2+ doped ZnS-CdS composite nanopowder and extension of sp-d exchange interactions and common d-d transitions. The variation in the energy bandgap varies as a function of cobalt concentration is due to structural modification. Photoluminescence spectrum reveals the defect-related emissions and shows the formation of luminescence. FT-IR spectrum confirmed the feature vibrational manner of Zn, Cd, O–H and sulfide ions are in the host lattice. The doping-induced magnetic properties are studied by vibrating sample magnetometer which matches with the theoretical values besides ferromagnetic nature. Magnetic studies confirm the ferromagnetic nature of the material. Surface morphology and chemical homogeneity studies were carried out by using SEM with EDAX. Transmission electron microscope recommends the crystalline nature of nanoparticles, with average particle size is of the order of 20-100nm.

A galvalume corrugated sheet was utilized as formwork for a reinforced concrete beam in flexure. A numerical model was validated to the experimentally obtained data, and further adopted to simulate the behavior of this composite structure under elevated temperatures. The properties and constitutive stress-strain data of the basic materials were obtained from experiments, and superimposed into the finite element model. The study concluded that the load carrying capacity of the member decreased as a direct function on temperature increase, and the cracking moment was very sensitive to the temperature fluctuation. The elevated temperatures also altered the failure mode.

Nanocomposites of cyanate ester resin (CER) filled with three different reactive amino-functionalized polyhedral oligomeric silsesquioxane (POSS) were synthesized and characterized. The addition of a small quantity (0.1 wt.%) of amino-POSS chemically grafted to the CER network led to increasing thermal stability of CER matrix. A significant increase of the glass transition temperature, Tg (DSC data), and the temperature of α relaxation, Tα (DMTA data), by 45-55 оС of CER matrix with loading of nanofillers was evidenced. CER/POSS films exhibited a higher storage modulus than that of neat CER in the temperature range investigated. It was evidenced that CER/aminopropylisobutyl (APIB)-POSS, CER/N-phenylaminopropyl (NPAP)-POSS, and CER/aminoethyl aminopropylisobutyl (AEAPIB)-POSS nanocomposites induced a more homogenous α relaxation phenomenon with higher Tα values and an enhanced nanocomposite elastic behavior. Furthermore, CER/amino-POSS nanocomposites possessed higher specific surface area, gas permeability (CO2, He), and diffusion coefficients (CO2) values than those for neat CER, due to increasing free volume of the nanocomposites studied that is very important for their gas transport properties. Permeability grew respectively by about 2 (He) and 3.5-4 times (СО2), and diffusion coefficient of CO2 increased approximately twice for CER/amino-POSS nanocomposites in comparison with the neat CER network. The efficiency of amino-functionalized POSS in improving the thermal and transport properties of the CER/amino-POSS nanocomposites increased in a raw of reactive POSS containing one primary (APIB-POSS) &lt; eight secondary (NPAP-POSS) &lt; one secondary and one primary (AEAPIB-POSS) amino groups. APIB-POSS had the least strongly pronounced effect, since it could form covalent bonds with the CER network only by reaction of one –NH2 group, while AEAPIB-POSS displayed the most highly marked effect, since it could easily be incorporated into the CER network via reaction of –NH2 and –NH– groups with –O–C≡N groups from CER.

Copper ferrite attracts a lot of interest from researchers as a material with unique magnetic, optical, catalytic and structural properties. In particular, the magnetic properties of this material are structurally sensitive and can be tuned by changing the distribution of Cu and Fe cations in octahedral and tetrahedral positions by controlling synthesis parameters. In this study, we propose a new simple and convenient method for the synthesis of copper ferrite nanoparticles using a strongly basic anion exchange resin in OH form. The effect and possible mechanism of polysaccharides addition on the elemental composition, yield and particle size of CuFe2O4 is investigated and discussed. It is shown that anion exchange resin precipitation leads to a mixture of unstable at standard temperature cubic (c-CuFe2O4) and stable tetragonal (t-CuFe2O4) phases. The effect of the reaction conditions on the c-CuFe2O4 stability is studied by temperature-dependent XRD measurements and discussed in terms of the cations distribution, Jahn−Teller distortion and Cu2+ and oxygen vacancies in the copper ferrite lattice. The obtained differences in the values of saturation magnetization and the coercive force of prepared samples are explained with a reference to variations in the particle sizes and the structural characteristics of copper ferrite.

This study evaluated the efficacy of experimental TEGDMA-functionalized dicalcium phosphate dihydrate (T-DCPD) filler-based resin-based composites (RBC) in preventing caries lesions around the restoration margins (secondary caries”, SC). Standardized Class-II cavities were made in sound molars having the cervical margin in dentin. Cavities were filled with a commercial resin-modified glass-ionomer cement (RMGIC) or experimental RBCs containing a BisGMA-TEGDMA resin blend and one of the following inorganic fractions: 60 wt.% Ba glass (RBC-0); 40 wt.% Ba glass, 20 wt.% T-DCPD (RBC-20); 20 wt.% Ba glass, 40 wt.% T-DCPD (RBC-40). An open-system bioreactor produced S. mutans biofilm-driven SC. Specimens were scanned using micro-CT to evaluate demineralization depths. Scanning Electron Microscopy and Energy-dispersive X-ray Spectroscopy characterized the specimens’ surfaces, while antimicrobial activity, buffering effect, and ion uptake by the biofilms were also evaluated. ANOVA and Tukey’s test were applied at p<0.05. RBC-0 and RBC-20 showed SC development in dentin, while RBC-40 and RMGIC significantly reduced the lesion depth at the restoration margin (p<0.0001). Initial enamel demineralization could be observed only around RBC-0 and RBC-20 restorations. A direct antibiofilm activity could explain SC reduction by RMGIC, while a buffering effect on biofilm’s acidogenicity explained the behavior of RBC-40. Experimental RBC with CaP-releasing functionalized T-DCPD filler could prevent SC with the same efficacy as F-releasing materials.

The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

With the increased scientific interest in green technologies, many researches have been focused on the production of polymeric composites containing naturally occurring reinforcing particles. Apart from increasing mechanical properties, these additions can have a wide range of interesting effects, such as increasing the resistance to bacterial and fungal colonization. In this work, different amounts of two different natural products, namely neem and turmeric, have been added to polyethylene to act as a natural antibacterial and antifungal product for food packaging applications. Microscopic and spectroscopic characterization showed that fractions up to 5% of these products can be dispersed into low-molecular weight polyethylene, while higher amounts could not be properly dispersed and resulted in an inhomogeneous, fragile composite. In vitro testing conducted with Escherichia coli, Staphylococcus aureus and Candida albicans showed a reduced proliferation of pathogens when compared to the polyethylene references. In particular, turmeric, resulted to be more effective against E. coli when compared to neem, while they had similar performances against S. aureus. Against C. albicans, only neem was able to show a good antifungal behavior, at high concentrations. Tensile testing showed that the addition of reinforcing particles reduces the mechanical properties of polyethylene, and, in the case of turmeric, it is further reduced by UV irradiation.

Composite membranes formed by sulfonated poly(ether ether ketone) (SPEEK) with embedded carbon quantum dots (CQDs) were used for detection and removal of heavy metal ions, such as lead and cadmium, from water. SPEEK is responsible for the capture of heavy metals based on the cation exchange mechanism, while CQDs detect their contamination by exhibiting changes in fluorescence. Water-insoluble “red” carbon quantum dots (rCQDs) were synthesized from p-phenylenediamine so that their photoluminescence was shifted from that of the polymer matrix. CQDs and the composites were characterized by several techniques: FTIR, Raman, UV/VIS, photoluminescence, XPS spectroscopies and AFM microscopy. The heavy metal ion concentration was analyzed by inductively coupled plasma–optical emission spectroscopy (ICP-OES). The concentration ranges were 10.8 - 0.1 mM for Pb2+ and 10.0 - 0.27 mM for Cd2+. The composite achieved 100% removal efficiency for lead and cadmium if the concentration was below a half of the ion exchange capacity of SPEEK. The regeneration of membranes in 1 M NaCl was also studied. SPEEK/rCQDs showed a turn-off effect more pronounced for lead. A second order law was effective to describe the kinetics of the process.

Steel construction is used more often these days as an alternative to the R.C.C. when light weight, high strength, large-span structures with a faster erection are required. Extensive studies have been done by researchers to study the seismic performance of reinforced concrete and steel structures, both in terms of elastic and inelastic behavior. Composite construction is also a recent advancement in the building industry with similar advantages. However, no emphasis has been given to the comparison between the inelastic behavior of steel and composite structures when subjected to lateral loads. This study compares the inelastic behavior of steel and a composite frame designed to have the same plastic moment capacity for structural members. The responses, such as the formation of hinges, story drifts, story displacements, lateral stiffness, ductility, maximum strength, energy dissipated, joint accelerations, and performance points, are compared with the aid of the building analysis and design software ETABS-18. For this, response spectrum analysis, pushover analysis and nonlinear direct integration time history analysis have been performed on both frames. For design and analysis, international codes such as IS 800-2007, IS 875 (Part I, II, IV), IS 1893-2002, AISC 360 (16 &amp; 10) and FEMA 440 have been used. Part of this study also aims at comparing the response of these frames when subjected to near field and far field earthquakes. It can be concluded from the results that the post yield performance of the composite frame is superior to that of the steel frame when seismically excited.

This report aimed to know the performance of local mineral-based composite ceramic. The materials used consist of Indonesian local minerals, which are jarosite and manganite minerals as sources of oxide iron and Mangan. The materials were synthesized using the precipitation method, whereas composite ceramic was fabricated using a screen printing method and fired at 600 oC using a furnace. The results of the characterizations indicate that the sample forms three phases on diffraction peaks. The differences in the resistance values in ambient and ethanol environments indicate that the sample has very different responses. The high porosity of the sample greatly support the gas adsorption process. Thus, the sample has a high level of sensitivity. With the above characteristics, the composite ceramic which was fabricated has the potential to be applied to gas sensors, especially ethanol gas sensors.

In the present study, the corrosion resistance of amorphous coating and composite coatings in 3.5 wt.% NaCl, 0.5 M H₂SO₄ and 10 wt.% NaOH solution were studied. The composite coatings exhibit superior corrosion resistance. When the content of AT13 （Al₂O₃–13 wt.% TiO₂）was 15 wt.%, the composite coating has the lowest corrosion current density (1.75×10^-6 A cm^-2), which is 5.14×10^-5 A cm^-2 for Fe-based metallic glassy coating, and the highest corrosion potential (-411 mV), which is -580 mV for Fe-based metallic glassy coating. The breakdown potential of the passivation film in 3.5 wt.% NaCl solution was much higher than that of 316L.The long-time immersion corrosion tests carried out on different coatings showed that the corrosion protection effect of coating was enhanced with the increase of the amount of AT13 added.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10^-4 Scm^-1 while the highest conductivity achieved was 8.2 × 10^-1 Scm^-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T₀ and T_deg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

This study endeavors the preparation and evaluation of Phenol Furfural Resin (PFR) from bagasse and its nanocomposites for Electrically Conductive Adhesives (ECAs) application. PFR was prepared with the furfural extracted from bagasse using modified acid digestion method. Three different formulations of PFR nanocomposites with conductive nanoparticles i.e., PFR-silver, PFR-graphite, and PFR-silver + graphite were prepared using 20-60 w/w% of fillers via impregnation method. Resultant products were characterized by FT-IR, SEM, EDS and XRD spectroscopy. Electrical conductivity was measured using four probe technique while band gap was calculated via Tauc plot. Virgin PFR has shown poor conductivity up to 2.6 × 10-4 Scm-1 while the highest conductivity achieved was 8.2 × 10-1 Scm-1 for nanocomposite constituted silver, graphite, and PFR with 40:30:20 ratios respectively. This synergism was exhibited because graphite and Ag NPs supply excellent junctions for building networks. Both tend to coalesce due to van der Waals forces and high surface energies, therefore conductive pathways numbers can be increased, and contact area can be effectively enlarged. This ternary composite has exhibited the lowest bandgap energy value i.e., 3.1 eV. Thermogravimetric temperatures T0 and Tdeg values were increased up to 120 °C and 484 °C respectively, showing significant increase in thermal stability. Therefore, the resultant nanocomposite material has good potential to be employed as ECAs in electronic industry.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

The reinforcing effect of boehmite nanoparticles (BNP) in epoxy resins for fiber composite lightweight construction is related to the formation of a soft but bound interphase between filler and polymer. The interphase is able to dissipate crack propagation energy and consequently increases the fracture toughness of the epoxy resin. Usually, the nanoparticles are dispersed in the resin and then mixed with the hardener to form an applicable mixture to impregnate the fibers. If one wishes to locally increase the fracture toughness at particularly stressed positions of the fiber-reinforced polymer composites (FRPC), this could be done by spraying nanoparticles from a suspension. However, this would entail high costs for removing the nanoparticles from the ambient air. We propose that a fiber fleece containing bound nanoparticles be inserted at exposed locations. For the present proof-of-concept study, an electrospun polycarbonate nonwoven and taurine modified BNP are proposed. After fabrication of suitable PC/EP/BNP composites, the thermomechanical properties were tested by dynamic mechanical analysis (DMTA). Comparatively, the local nano-mechanical properties such as stiffness and elastic modulus were determined by atomic force microscopy (AFM). An additional investigation of the distribution of the nanoparticles in the epoxy matrix, which is a prerequisite for an effective nanocomposite, is carried out by scanning electron microscopy in transmission mode (TSEM). From the results it can be concluded that the concept of carrier fibers for nanoparticles is viable.

Antimicrobial edible coatings could eliminate pathogen contamination risk on the surface of meat and poultry products during storage. In this study, the edible coating (EC) based on wheat gluten, Pistacia vera L. tree resin (PVR), and essential oil (EO) of PVR were applied on chicken breast fillets (CBF) by dipping method to prevent the growth of Salmonella Typhimurium and Listeria monocytogenes. The samples were packed in foam trays wrapped with low-density polyethylene stretch film and stored at 8°C for 12 days to observe antimicrobial effects and sensory properties. The total bacteria count (TBC), L. monocytogenes, and S. Typhimurium were reported during the storage. All samples coated with EC containing 0.5, 1, 1.5, and 2% v/v EO (ECEO) decreased microbial growth significantly compared to control samples. The growth of TBC, L. monocytogenes, and S. Typhimurium was suppressed by 4.6, 3.2, and 1.6 logs, respectively, at the end of 12 days on the samples coated by ECEO (2%) compared to uncoated controls (p&lt;0.05). Coating with ECEO (2%) also preserved appearance, smell, and general acceptance parameters better than uncoated raw chicken (p&lt;0.05) on the 5th day of storage. In grilled chicken samples, ECEO (2%) did not significantly change the sensory properties of appearance, smell, and texture but had increased taste and general acceptance scores (p&gt;0.05). So, ECEO (2%) can be a feasible and reliable alternative to preserve chicken breast fillets without affecting their sensory properties adversely during the shelf life.