Boeing and Airbus developed a special testing procedure to investigate the compressive response of laminates that have been impacted (following standards ASTM D 7137 and DIN 65561). This study focuses on both experimental and numerical analysis of Kevlar plates subjected to compression after impact. To ensure high quality and appropriate mechanical properties, the composite plates were manufactured using autoclaving. The DIN 65561 protocol was followed for all three test systems. Initially, ultrasonic C-scanning was performed on all plates before testing to confirm they were free of any significant defects arising from the manufacturing process. Subsequently, low-energy impact testing was conducted at levels ranging from 0 to 8 Joules. Three specimens were tested at each energy level. After the impact, all specimens underwent ultrasonic C-scanning again to assess the internal delamination damage caused by the impactor. Finally, both pristine and impacted specimens were subjected to compressive testing using the special jig specified in DIN 65561. The compressive impact strength results obtained from these tests were plotted against the delamination area measured by C-scanning. This data was then compared to results obtained from specimens with artificial damage. Semi-empirical equations were used to fit both sets of curves. The same procedure (impact testing, C-scanning, and data analysis) was repeated to investigate the relationship between impact energy and total delamination area. Lastly, finite element modeling was employed to predict the buckling stresses that develop under compression in the impacted systems studied. These modelling approaches have demonstrated good accuracy in reproducing experimental results for CAI tests.

Objective: Mechanical bowel preparation is essential for the visualisation of the colon during colonoscopy, and previous studies have identified changes in gut microbiota composition after bowel preparation and colonoscopy. Considering the gut microbiota is increasingly implicated in mood, we aimed to explore the potential impact of this intervention on mood and the microbiota-gut-brain axis. Methods: We conducted a pre-post intervention study, with timepoints of one week before and one month after bowel preparation and colonoscopy, in community-dwelling adults referred for colonoscopy. Our primary outcome was change in average Hospital Anxiety and Depression Scale depression sub-scores using generalised estimating equations. We also examined changes in average anxiety, stress, and quality of life scores, and faecal microbiota composition and potential function using 16S rRNA sequencing. We further explored associations between changes in depressive symptoms and the gut microbiota and conducted post-hoc analyses to explore potential effect modifiers. Key Results: 59 participants were included in the analyses. Depressive symptoms decreased one-month post-procedure compared to baseline (adjusted β=−0.64; 95%CI: −1.18, −0.11). Irritable bowel syndrome (IBS) appeared to moderate this relationship (1.78; 0.292, 3.26); depressive symptoms increased in those with, and decreased in those without, IBS. Changes in gut microbiome composition included reduced alpha diversity, modest effects on beta-diversity, and increases in genera associated with potential health benefits, one-month post-procedure compared to baseline. Increases in the CLR-transformed abundance of Ruminococcaceae UCG-009 were associated with improvements in depressive symptoms. Conclusions: There is preliminary evidence of a potential mental health effect of bowel preparation and colonoscopy, which may be associated with changes to the gut microbiota. There may also be a differential mental health impact of this procedure for those with and without IBS. Considering the limitations of our study, further research is required to confirm these findings and their clinical relevance.

In the proposed article, the issues of increasing the synchronizing ability of the system of coordinated rotation of asynchronous motors are considered. Based on the T-shaped equivalent circuit, electromechanical relationships were obtained with changes in the value of the total rotor resistance and the supply voltage of individual motors. An algorithm for calculating the torques, stator and rotor currents of the motors of the system has been compiled. Based on the calculations obtained, the mechanical characteristics of the system asynchronous motors are constructed for various values of total resistance, supply voltages and rotor positions. The obtained data and graphs confirm the adequacy of the theory obtained in an analytical way. Functional and structural diagrams in small scales have been compiled, which allow simulating transient operation modes of multi-motor asynchronous electric drives in the Matlab application package. Multi-motor asynchronous electric drives with adjustable supply voltages, as well as with preliminary synchronization and synchronous braking, have been developed. Compilation of a program for the stability of a nonlinear system of a multi-motor asynchronous electric drive (MAEDs) with a thyristor voltage converter (TVC) in Matlab. Also, the modes of soft start, load shedding and surge on the motor shaft are simulated, confirming the stability of the system.

The article presents the author’s works in the field of modifications and modeling of the PQC CSIDH algorithm on non-cyclic supersingular Edwards curves and its predecessor CRS scheme on ordinary non-cyclic Edwards curves are reviewed. Lower estimates of the computational speed gains of the modified algorithms over the original ones are obtained. The most significant results were obtained by choosing classes of non-cyclic Edwards curves connected as quadratic twist pairs instead of cyclic complete Edwards curves, as well as the method of algorithm randomization as an alternative to “constant time CSIDH.” It is shown that in the CSIDH and CSIKE algorithms, there are two independent cryptosystems with the possibility of parallel computation, eliminating the threat of side-channel attacks. For the CRS scheme, there are four such cryptosystems. Integral lower bound estimates of the performance gain of the modified CSIDH algorithm are obtained at 1.5 ∙ 29, and for the CRS scheme are 3 ∙ 29.

During prolonged standing, insufficient calf muscle pumping accompanies venous stasis and hypertension in the lower legs, resulting in valve dysfunction, venous wall problems, and subsequent inflammation. Compression therapy, which includes medical compression stockings (MCS) and mechanical intermittent pneumatic compression (IPC), is one of the most effective therapeutic interventions for treating chronic venous diseases. This study aimed to investigate the safety and efficacy of IPC and MCS, and the optimal protocol of compression therapy for chronic venous disease. This crossover trial was conducted for healthy, long standing workers (>8 h daily) with leg edema and pain. Four groups were established for each visit: group A (resting after work without MCS), group B (resting after work with MCS), group C (IPC after work without MCS), and group D (IPC after work with MCS). The primary outcome was the visual analogue scale (VAS) score for leg pain. The secondary outcomes were leg volume (mL), circumference (cm), extracellular fluid/total body fluid (ECF/TBF), and extracellular water/total body water (ECW/TBW) through bioimpedance analysis. Outcomes were assessed before work (T0), after work (T1), and 60 minutes after intervention (T2). We included 39 healthy volunteers, aged 30.03±7.56 years. All four groups had significantly increased leg pain after work (T0-1) but improved 60 minutes after intervention (T1-2), particularly group C (decreased VAS by 1.9). When leg swelling was compared at T0 and T1, groups A and C showed significant increases in leg volume and circumference, indicating significant work-induced edema, whereas groups B and D showed no change or even a decrease. After interventions, leg volume and circumference significantly decreased in groups A and C, although groups B and C did not show significant improvement. The ECF/TBF and ECW/TBW of all groups decreased after interventions. Leg pain and edema after prolonged standing in healthy adults were safely and effectively improved by IPC. Although MCS also reduced leg edema immediately after work, it did not show significant improvement in leg pain at T0-1–and T1-2, nor in swelling at T1-2.

The integration of modern technologies like intramedullary fixators and advanced biometallic alloys has revolutionized traumatology and orthopedics. While these innovations have improved treatment, the exploration of new materials for implants persists. Tantalum and niobium, both non-toxic with similar properties, are preferred for titanium-based biomedical alloys due to their exceptional biocompatibility and corrosion resistance. Acting as stabilizers in titanium alloys, they form passive oxide layers resisting corrosion and remain compatible with biological systems. The novel Ti21Nb6Ta (TNT) alloy promises enhanced osteosynthesis outcomes. Our in vivo research on experimental animals evaluated the biocompatibility and osteoinduction of TNT compared to Ti-6Al-4V (BT-6) alloy (control group). The study comprised three experiments across different animal species, assessing acute toxicity, irritant effects, and long-term biocompatibility and osteoinduction through simulated osteosynthesis. Results indicated that aqueous extracts from both alloys were non-toxic and non-irritating. Furthermore, both demonstrated high biocompatibility and active osteoinduction potential after three months of implantation.

The inherited ‘EIA’ process at Brexit is based on a ‘Project’ period from Inception tothe start of construction works. The ‘Incompleteness’ of the process covers andidentifies stages that will impact on the environmental cycle: construction period,operational life, de-commissioning and a return to acceptable environmental footprint.A master environment structure-plan framework is required to commence with theupgrading of the complete ‘EIA’ process, embracing separate limbs for the UK’spriority environmental targets for climate change, and other major adverse effectswhich result in serious ‘harm’ to the UK environment. The identification of the processfor ‘incompleteness’ requires effective sustainability, and inclusion of effectivemanagement tools, for the essential ‘monitoring/control/recording’ proceduresthroughout the project life and the natural environmental cycle. This will allow theopportunity for a new approach to a structured ‘Suite of EIAR Directives’, to enable a‘EIAR’ regime that ‘will remain fit and proper for UK purpose’.

The study aims to investigate SEBT indicators in female representatives of various types of single combats and to identify differences between them. The research was conducted at the Lviv State University of Physical Culture named after Ivan Bobersky, Ukraine in November-December 2023. Female university students aged 18-22 participated in the study: 10 representatives from Kyokushinkai karate, 6 from boxing, 8 from fencing (epee), and 7 from WKF karate. Research methods: analysis of literary sources and materials from the Internet; anthropometry; SEBT; methods of mathematical statistics. The hypothesis of this work is confirmed by the results of the conducted research, which indicates that engaging in a certain type of combat sport has its specific imprint (profile) on the SEBT indicators. The results of the correlations of SEBT indicators in boxing and fencing representatives indirectly indicate the asymmetric impact of these single combats on the arms and legs of a person's body. The SEBT results of Kyokushinkai karate representatives indicate the symmetry and uniform development of the left and right parts of the body. The indicators of the WKF karate representatives occupy an intermediate place in this comparison: the peculiarities of their SEBT indicators show that along with symmetrical manifestations, asymmetric ones are also observed.

Systemic inflammation and coronary microvascular endothelial dysfunction are essential pathophysiological factors in heart failure with preserved ejection fraction (HFpEF) that support the use of statins. The pleiotropic properties of statins, such as anti-inflammatory, antihypertrophic, antifibrotic, and antioxidant effects, are generally accepted and may be beneficial in HF, especially in HFpEF. Numerous observational clinical trials have consistently shown a beneficial prognostic effect of statins in patients with HFpEF, while the results of two larger trials in patients with HFrEF have been controversial. Such differences may be related to a more pronounced impact of the pleiotropic properties of statins on the pathophysiology of HFpEF and pro-inflammatory comorbidities (arterial hypertension, diabetes mellitus, obesity, chronic kidney disease) that are more common in HFpEF. This review discusses the potential mechanisms of statin action that may be beneficial for patients with HFpEF, as well as clinical trials that have evaluated the statin effects on left ventricular diastolic function and clinical outcomes in patients with HFpEF.

An observational cohort study of patients diagnosed with endometrial cancer (EC) stage IA G1, or atypical endometrial hyperplasia (AHE), undergoing organ-preserving treatment, was conducted. Objective of the study: to determine CDO1, PITX2, and CDH13 gene methylation levels in early endometrial cancer and atypical hyperplasia specimens obtained before organ-preserving treatment in the patients with adequate response and with insufficient response to hormonal treatment. Materials and methods: 41 endometrial specimens obtained during diagnostic uterine curettage in women with EC (n=28) and AEH (n=13), willing to preserve reproductive function, were studied; 18 specimens of endometrial cancer IA stage G1 from peri- and early postmenopausal women (comparison group) were included in the study. The control group included 18 endometrial specimens from healthy women obtained by diagnostic curettage for missed abortion and/or intrauterine adhesions. Methylation levels were analyzed using the modified MS-HRM method. Results: All 13 women with AEH had complete response (CR) to medical treatment. In the group undergoing organ-preserving treatment for uterine cancer IA stage G1 (n=28), 14 patients had complete response (EC CR group) and 14 had not (non-CR). It was found that all groups had statistically significant differences in CDO1 gene methylation levels with the control group (p<0.001) except for the EC CR group (p=0.21). The p-value of difference between EC CR and EC non-CR groups was <0.001. The differences in PITX2 gene methylation levels between the control and study groups were also significantly different (p<0.001), except for AEH group (p=0.21). For the difference between EC CR and EC non-CR groups, the p-value was 0.43. For CDH13 gene methylation levels, statistically significant differences were found between the control and EC non-CR groups (p<0.001), and the control and EC comparison groups (p=0.005). When comparing the EC CR group with EC non-CR group, the p-value for this gene was <0.001. Simultaneous assessment of CDO1 and CDH13 genes methylation allowed to accurately distinguish between EC CR and EC non-CR groups (AUC=0.96). Conclusion: Assessment of CDO1 and CDH13 gene methylation in endometrial specimens from patients with endometrial cancer (IA stage G1), planned for medical treatment, can predict the treatment outcome.

German noise action plans aim to reduce negative health outcomes from noise exposure and identify quiet areas free of noise pollution. Quiet area identification in German noise action plans is based primarily on noise mapping and spatial analysis and not empirical or qualitative data about acoustic environments, thus leaving a gap in the understanding of the quality of formally recognized quiet areas in noise action plans. This work presents a comparative empirical case study in Dortmund, Germany, with the aim to describe the diurnal dB(A) and biophonic properties of quiet areas versus noise 'hot spots'. Sound observations were collected (n=282,764) in five different natural or recreational land use patch types larger than four acres within 33 proposed quiet areas in Dortmund (n=70) and 23 noise hot spots between April 27^th, 2022 and March 2^nd, 2023. We find that quiet areas are on average more than 20 dB(A) quieter than noise hot spots almost every hour of the day. Forests, managed tree stands, cemeteries, and agriculture diel patterns are dominated by dawn dusk chorus in spring and summer, whereas sport and recreation as well as noise hot spots are dominated by traffic and human noise. A novel composite biophony mapping procedure is presented that finds distinct temporal distribution of biophony in forested and agriculture peri-urban locations positively associated with patch size, distance away from LDEN > 55, proximity to water, and the number of vegetation layers in the plant community. Anthrophony distribution dominates urban land uses in all hours of the day, but expands during day and evening and contracts at night and in dusk hours. The procedures presented here illustrate how qualitative information regarding quiet areas can be integrated into German noise action planning.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the synthesis as well as theoretical considerations concerning to design of gear size ranges. The synthesis consists in composition (aggregation) of single details into units – according to the rule: “from details up to general view”. The basics of the object-oriented synthesis were formulated. Furthermore, the consecutive stages of synthesis were formulated. The interactions between these stages were discussed. Some aspects were described in details e.g.: creation of interfaces for performance of the embodiment phase the designed artefact via CAD system drawing with specification (dimensions are still parametrically set). The final step of the procedure is creation of so called substantial (concrete) form of artifacts i.e. final assignment of dimensions which stored in the special data base. The final stage of the design process is issuing of technical documentation (technical drawings) created automatically via CAD system. The considerations are terminated by the list of advantages connected with the object-oriented approach to design (in comparison to the traditional way).

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Design process can be divided into stages of analysis and synthesis. This paper presents the application of the object-oriented technique to the analysis as well as theoretical considerations concerning to design of gear size ranges. This analysis consists in decomposition of the designed artefact (a gear) according to the rule “from general to details view”. The basics of the object-oriented analysis were formulated. Furthermore, design phases and the objects related to theses phases were discussed. The following models have been considered: hierarchical model, entity-relationship model, data-flow model and object model. Analysis is additionally connected with interactions between particular design phases.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

The goal is the optimal synthesis of the parameters of the control law for a nonlinear satellite attitude control system under constraints related to the saturation effect of reaction wheels. The maximum stability degree of the control system is considered as a criterion for the optimality of the parameters of the control law, and the absolute values of the control torques and angular velocities of the reaction wheels, achievable within the limits of the physical characteristics of the drives, are considered as constraints. The solution to the optimal synthesis problem is based on the transformation of the nonlinear control system model into a linear model, within the framework of the problem of global asymptotic stability of the control system is also guaranteed. The problem is decomposed into a subproblems of obtaining the optimal transient process shape in the control system and considering the constraints. A method of synthesizing the optimal transient process shape based on the criterion of maximum stability degree had been developed. An analytical method of determining the optimal values of the control law parameters, based on decomposing the normalized characteristic polynomial in the linear model into three identical factors had been proposed. A method with regards to the constraints of the control torque and angular speed of the reaction wheels, based on transitioning from relative to real time is developed. An algorithm for calculation of the transition scale from relative to real time, ensuring the fulfillment of all constraints in the optimal synthesis problem, is proposed. An example demonstrating the efficiency and simplicity of the proposed methods and algorithm for targeted selection of technical characteristics of the control system, considering the maximum absolute values of angular speeds and control torques of the reaction wheels, is provided.

The Chinese government has expressed great confidence in the role of green finance in fulfilling its carbon neutrality commitment. However, the effectiveness of green finance, especially under the impact of emergencies such as the COVID-19 pandemic scenario, requires further examination. Using data from 2000 to 2020 in China, the correlation between green finance and carbon dioxide (CO2) emissions has been analyzed, both in BaU scenario and the COVID-19 scenario. The following conclusions were drawn: (1) In BaU scenario, green finance can effectively reduce CO2 emissions, especially through government green expenditure and green credit; (2) In COVID-19 scenario, although there is no direct relationship between the pandemic and carbon emissions, the data shows that the pandemic has hindered the progress of green finance, weakened its ability to curb carbon emissions, and indirectly led to an increase in carbon emissions. This study not only clarifies the mechanism by which the COVID-19 pandemic affects carbon emissions through the green finance system but also addresses the common problem of data scarcity in green finance research.

Outer particles collision with certain dynamic object is not a pure impact wear behavior; it is typically accompanied by sliding wear phenomena. This study aimed investigating the impact-sliding wear performance of three different TC17 titanium alloys. One was untreated, and the other two were subjected to laser shock peening (LSP) by 5 and 7 J pulse energy, respectively. Wear test was performed on a novel impact-sliding wear testing rig, which can realize multiple impact-sliding motions by changing motion parameters in x and z directions. Present results showed that wear resistance of both treated samples improved compared with the untreated alloy. Given the increase in wear cycles, increment in wear rate of the untreated sample was constantly higher than those of treated samples. All results can be attributed to the increase in surface hardness of the material and residual compressive stress, which was also introduced after LSP.

Endometriosis is a prevalent chronic inflammatory disease characterized by a considerable delay between initial symptoms and diagnosis through surgery. The pressing need for a timely, non-invasive diagnostic solution underscores the focus of current research efforts. This study examines the diagnostic potential of the menstrual blood lipidome. The lipid profile of 39 samples (23 women with endometriosis and 16 patient of control group) was acquired using reverse-phase high-performance liquid chromatography-mass spectrometry with LipidMatch processing and identification. Profiles were normalized based on total ion counts. Significant differences in lipids were determined using the Mann-Whitney test. Lipids for the diagnostic model, based on logistic regression, were selected using a combination of variance importance projection filters and Akaike information criteria. Levels of ceramides, sphingomyelins, cardiolipins, triacylglycerols, acyl- and alkenyl-phosphatidylethanolamines, and alkenyl-phosphatidylcholines increased, while acyl- and alkyl-phosphatidylcholines decreased in cases of endometriosis. PE P-16:0/18:1 and CL 16:0_18:0_22:5_22:6 serve as marker lipids in the diagnostic model, exhibiting a sensitivity of 81% and specificity of 85%. The diagnostic approach based on dried spots of menstrual blood holds promise as an alternative to traditional non-invasive methods for endometriosis screening.

The extraocular muscles (EOMs) possess unique characteristics that set them apart from other skeletal muscles. These muscles, responsible for eye movements, exhibit remarkable resistance to various muscular dystrophies and aging, presenting a significant contrast to the vulnerability of skeletal muscles to these conditions. In this review, we delve into the cellular and molecular underpinnings of the distinct properties of EOMs. We explore their structural complexity, highlighting differences in fiber types, innervation patterns, and developmental origins. Notably, EOM fibers express a diverse array of myosin heavy chain isoforms, retaining embryonic forms into adulthood. Moreover, their motor innervation is characterized by a high ratio of nerve fibers to muscle fibers and the presence of unique neuromuscular junctions. These features contribute to the specialized functions of EOMs, including rapid and precise eye movements. Understanding the mechanisms behind the resilience of EOMs to disease and aging may offer insights into potential therapeutic strategies for treating muscular dystrophies and myopathies affecting other skeletal muscles.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

As the fast growth of information technology (IT), the safety of image transmission and the storing of images are increasingly concerned. Traditional image encryption algorithms have certain limitations in transmission and security, so there is an urgent need for a secure and reliable image encryption algorithm. A universal compression sensing (CS) image encryption (IE) algorithm based on DNA-triploid mutation (DTM) is presented in this paper. Firstly, by using CS algorithm an image is compressed while obtaining a range of chaotic sequences by iteration of chaotic map. Then DNA sequences are generated by encoding the image, and based on the DTM, new mutant DNA sequences are generated according to specific rules. Next, the chaotic sequences are operated at the DNA level to do confusion and diffusion operations on the image to ensure the security of the data. At last, DNA decoding is carried out to obtain the compressed-encrypted image. Both simulation experiments and performance tests fully show that a high level of security and reliability of the proposed algorithm in protecting image privacy is achieved.

Succinate is proposed to be a mediator of muscle exercise-induced adaptations. We studied metabolic health and changes of muscle mass in 6-month-old male mice after 12 weeks of feeding regular diet (RD, 13.4 kcal% fat, 66.8 kcal% carbohydrate, 29.8 kcal% protein), high fat diet (HFD, 60 kcal% fat, 20 kcal% carbohydrates, 20 kcal% protein) and ketogenic diet (KD, 80 kcal% fat, <1 kcal% carbohydrates, 20 kcal% protein) with or without 2% succinate supplements (SUS) in drinking water (n=8-12 per group). Functional overloading of the plantaris muscle (PL) was induced in a group of mice by denervation of the gastrocnemius and soleus muscles at week 6 of feeding different diets. HFD induced the greatest (p < 0.001) increase in body and fat mass. HFD and KD lead to significant (p < 0.01) impairment in glucose tolerance compared to RD. SUS blunted (p < 0.01) initial surge in energy intake when mice were switched from RD to HFD, but did not influence any measures of metabolic health after 12 weeks of the study. Functional overloading lead to ~25% increase in PL mass which was not affected by diet or SUS. In conclusion, SUS does not have a long-term effect on metabolic health or muscle mass.

Vaccines trigger a complicated immunological response that includes B and T cells, with B cells producing antibodies. SARS-CoV-2 immunity weakens over time after vaccination. Discovering key changes in antigen-reactive antibodies over time after vaccination could help improve vaccine efficiency. In this study, we collected data on blood antibody levels in a cohort of healthcare workers vaccinated for COVID-19 and obtained 73 antigens in samples from four groups according to the duration after vaccination, including 104 unvaccinated healthcare workers, 534 healthcare workers within 60 days after vaccination, 594 healthcare workers between 60 and 180 days after vaccination, and 141 healthcare workers over 180 days after vaccination. An efficient machine learning based framework containing four feature selection methods (least absolute shrinkage and selection operator, light gradient boosting machine, Monte Carlo feature selection, and maximum relevance minimum redundancy) and four classification algorithms (decision tree, k-nearest neighbor, random forest, and support vector machine) was designed to screen out essential antigens. Several efficient classifiers with weighted F1 value around 0.75 were constructed. This study revealed that S1+S2, S1.mFcTag, S1.HisTag, S1, S2, Spike.RBD.His.Bac, Spike.RBD.rFc, and S1.RBD.mFc were most highly ranked among all features, where S1 and S2 are the subunits of Spike, and the suffixes represent the tagging information of different recombinant proteins. Meanwhile, the classification rules were extracted from the optimal decision tree to explain quantitatively the roles of antigens in the classification. This study identified antibodies associated with decreased clinical immunity based on populations with different time spans after vaccination. These antibodies have important implications for maintaining long-term immunity to SARS-CoV-2.

Singapore, being a land-scarce country, is heavily dependent on imported food, which poses a challenge in ensuring food security. In addition, the substantial amount of food waste generated in Singapore further deepens food insecurity challenges, imposing enormous pressure on the country's food and land resources. In the recent years, valorising food waste streams into higher value products has been an increasing trend in tackling food wastage due to its economical and environmental benefits. This paper provides a thorough review on food waste valorisation in Singapore and summarizes critical information from the current food landscape to the food waste management strategies adopted. The review highlights the prototypes developed from food waste streams by the local research and development capabilities and the technological processing and techniques used for versatile applications ranging from food and nutraceuticals to urban agriculture. The challenges associated with the valorisation of food waste are also addressed. Two ambitious Initiatives by the Singapore government Zero Waste Plan and the 30-by-30 food security goal to encourage food waste valorisation are explored and presented. The review serves as a reference for other countries in ensuring food security and achieving sustainable development goals.

Background: Peyronie’s disease (PD) represents a challenging urological disease, due to not optimal post-operative surgical outcomes. We aim to evaluate if vacuum erection devices (VED) treatment before pe-nile curvature surgery is able to improve the post-operative surgical outcomes. Methods: All enrolled patients were assigned to the following groups: a) treatment group, VED treatment (3 times per week) starting 3 months before surgery and (3 times per week) one months after surgery and b) control group, VED treatment (3 times per week) one months after surgery. Follow-up urologic visits were scheduled at 3 and 6 months after surgery and the two groups were compared. Results: Thirty-eight patients have been enrolled (median age 67 years, 57-74, IQR), 20 in the treatment group and 18 in the control group. At the follow-up visits, the two groups are different in terms of IIEF-5 (26 vs 24; p=0.02), ‘yes’ to SEP2 and 3 (85% vs 55%; p<0.001, 85% vs 50%; p<0.001, respectively) and PDQ (-16 vs -11; p=0.03). Complete correction of penile curvature was achieved in 36 patients (94.7%). In the treatment group, no hourglass deformity has been reported, while in the control group 1 patient reported a mild hourglass deformity. In the treatment group, we obtained a longer total penile length (median +1.5 cm). The overall satisfaction rate was 98% in the treatment group and 96% in the control group. Conclusions: The VED treatment before penile curvature surgery in patients affected by PD is able to improve the post-operative surgery.

For the set of probability measures ${\sf I}(X)$, where $X$ is a compact Hausdorff space, we propose a new way to introduce the topology by using open subsets of the space $X$. Then, among other things, we give a new proof that for a compact Hausdorff space $X$ the space ${\sf I}(X)$ is also a compact Hausdorff space. For a Tychonoff space $X$, we consider the topological space ${\sf I_{\tau}}(X)$ of $\tau$-smooth idempotent probability measures on $X$,and show that the space ${\sf I_{\tau}}(X)$ is \v{C}ech-complete if and only if the given space $X$ is \v{C}ech-complete.

With recent advancements in network technology and spread of Internet, use of social network services and Internet of Things devices has flourished, leading to a continuous generation of large volumes of graph stream data, where changes, such as additions or deletions of vertices and edges occur over time. Additionally, owing to the need for efficient use of storage space and security requirements, graph stream data compression has become essential in various applications. Even though various studies on graph compression methods have been conducted, most of them do not fully reflect the dynamic characteristics of graph streams and complexity of large graphs. In this paper, we propose a compression scheme using provenance data to efficiently process and analyze large graph stream data. It obtains provenance data by analyzing graph stream data and builds a pattern dictionary based on this to perform dictionary-based compression. By improving the existing dictionary-based graph compression methods, it enables more efficient dictionary management through tracking pattern changes and evaluating their importance using provenance. Furthermore, it considers the relationships among sub-patterns using an FP-tree and performs pattern dictionary management that updates pattern scores based on time. Our experiments show that the proposed scheme outperforms existing graph compression methods in key performance metrics, such as compression rate and processing time.

China historically exhibits spatial differentiation from population distribution to ecological or economic development, and the forest pest control work is an epitome of this tendency. In recent times, global warming, man-made monoculture tree plantations, increasing human population density and intensified international trade aggravate forest pest outbreaks. Although Chinese government has complied with the internationally recommended practices, few stones remain unturned due to existing differential regional imbalance of forest pest distribution and control abilities. Evidence shows that the high-income provinces in the south have taken advantage of economic and technological superiority, resulting in the adoption of more efficient pest-control measures. To the contrary, in economically underdeveloped provinces of the northwest, a paucity of financial support has led to serious threats of pest damage that almost mirrored the demarcations of the Hu Huanyong Line. In this paper, we propose introducing public-private partnership (PPP) model into forest pest control and combining the national strategies to enact regional prevention measures in order to break the current spatially differentiated trends in China.

The ductile behavior of strain hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions for applications where high energy dissipation is needed, such as earthquake, impact by a projectile, or blast. However, the superior tensile ductility of SHCC due to multiple cracking does not necessarily entail compressive and shear ductility. As an effort to characterize the behavior of SHCC under impact compressive and shear loading, relevant to the mentioned high-speed loading scenarios, the paper at hand studies the performance of a SHCC and its constituent cement-based matrices using the split-Hopkinson bar method. For compression experiments, cylindrical specimens with a length-to-diameter ratio (l/d) of 1.6 were used. The selected length of the sample led to similar failure modes under the quasi-static and impact loading conditions, which was necessary for a reliable comparison of the obtained compressive strengths. The impact experiments were performed in a split-Hopkinson pressure bar (SHPB) at a strain rate that reached 110 s-1 at the moment of failure. For shear experiments, a special adapter was developed for a split-Hopkinson tension bar (SHTB). The adapter enabled performing impact shear experiments on planar specimens using the tensile wave generated in the SHTB. Results showed a dynamic increase factor (DIF) of 2.3 and 2.0 for compressive and shear strength of SHCC, respectively. As compared to the non-reinforced constituent matrix, the absolute value of the compressive strength was lower for the SHCC. Contrarily, under shear loading, the SHCC yielded the higher shear strength than the non-reinforced matrix.

Introduction: Despite great advances in the treatment of oncological diseases, the development of medical technologies to prevent or reduce complications of therapy, in particular, those associated with surgery and the introduction of antibiotics remains relevant. The aim of the study: to evaluate the effectiveness of the use of autoprobiotics based on indigenous non-pathogenic strains of Enterococcus faecium and Enterococcus hirae in the complex therapy of colorectal cancer (CRC) in the early postoperative period. Materials and methods: A total of 36 patients diagnosed with CRC were enrolled in the study. The study group (Group A) comprised 24 CRC patients who received autoprobiotic therapy in the early postoperative period, while the control group (Group C) included 12 CRC patients without autoprobiotic therapy.Prior to surgery and between days 14-16 post-surgery, comprehensive evaluations were conducted on all patients, encompassing the following: stool and gastroenterological complains analysis. examination of the gut microbiota (bacteriological study, quantitative polymerase chain reaction, metagenome analysis), analysis of interleukins in serum. Results: The use of autoprobiotics led to decrease dyspeptic complaints after surgery, was associated with absence of postoperative complications, did not cause side effects, led to a decrease in the level of pro-inflammatory cytokines (IL-6 and IL-18) in the blood serum. The use of autoprobiotics led to positive changes in the structure of escherichia and enterococci populations, the elimination of Parvomonas micra, Fusobacterium nucleatum, decrease in the quantitative content of Clostridium perfringens, Akkermansia muciniphila. Metagenomic analysis (16S rRNA) revealed an increase in alpha diversity. Conclusion: The administration of autoprobiotics in the postoperative period is highly effective and safe in the comprehensive treatment of colorectal cancer patients. Future studies will allow the discovery of additional fine mechanisms of autoprobiotic therapy and its impact on the digestive, immune, endocrine and neural systems.

This article explores the geothermal resources of Kazakhstan's Zharkent Basin, with a specific focus on the high-temperature geothermal sources in the Almaty region of Southern Kazakhstan. The research aims to analyze the energy characteristics of the Organic Rankine Cycle (ORC) for harnessing low-enthalpy geothermal energy for small-scale electricity generation. A detailed thermodynamic model was developed, employing R134a as the working fluid. An in-depth analysis of the Zharkunak field (Zharkent, Almaty region) revealed that well 5539, with its notably high temperatures, offers the highest potential for geothermal electricity production, achieving an annual output of approximately 10,371 MWh. The total electric power output from the studied wells in the region is estimated at 20,111 MWh annually, representing a significant contribution towards sustainable energy production and reducing reliance on traditional coal-fired power plants. The study concludes that the Organic Rankine Cycle is not only a viable and efficient technology for utilizing low-enthalpy geothermal resources to generate electricity on a small scale, but also a key player in enhancing energy independence. By leveraging local geothermal energy, the Almaty region can significantly reduce its reliance on external energy sources, thereby fostering sustainable development and reducing environmental impacts.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

In current severe global emergency situation of 2019-nCov outbreak, it is imperative to identify vulnerable and susceptible groups for effective protection and care. Recently, studies found that 2019-nCov and SARS-nCov share the same receptor, ACE2. In this study, we analyzed five large-scale bulk transcriptomic datasets of normal lung tissue and two single-cell transcriptomic datasets to investigate the disparities related to race, age, gender and smoking status in ACE2 gene expression and its distribution among cell types. We didn’t find significant disparities in ACE2 gene expression between racial groups (Asian vs Caucasian), age groups (>60 vs <60) or gender groups (male vs female). However, we observed significantly higher ACE2 gene expression in former smoker’s lung compared to non-smoker’s lung. Also, we found higher ACE2 gene expression in Asian current smokers compared to non-smokers but not in Caucasian current smokers, which may indicate an existence of gene-smoking interaction. In addition, we found that ACE2 gene is expressed in specific cell types related to smoking history and location. In bronchial epithelium, ACE2 is actively expressed in goblet cells of current smokers and club cells of non-smokers. In alveoli, ACE2 is actively expressed in remodelled AT2 cells of former smokers. Together, this study indicates that smokers especially former smokers may be more susceptible to 2019-nCov and have infection paths different with non-smokers. Thus, smoking history may provide valuable information in identifying susceptible population and standardizing treatment regimen.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Optical coherence tomography (OCT) is a non-invasive imaging technique widely used in ophthalmology for visualizing retinal layers, aiding in early detection and monitoring of retinal diseases. OCT is useful for detecting diseases such as age-related macular degeneration (AMD) and diabetic macular edema (DME), which affect millions of people globally. Over the past decade, the area of application of Artificial Intelligence (AI), particularly Deep Learning (DL), has significantly increased. The number of medical applications is also rising, with solutions from other domains being increasingly applied to OCT. The segmentation of biomarkers is an essential problem that can enhance the quality of retinal disease diagnostics. For 3D OCT scans, AI is beneficial since manual segmentation is very labor-intensive. In this paper, we employ the new SAM 2 and MedSAM 2 for the segmentation of OCT volumes for two open-source datasets, comparing their performance with the traditional U-Net. The model achieved an overall Dice score of 0.913 and 0.902 for macular holes (MH) and intraretinal cysts (IRC) on OIMHS and 0.888 and 0.909 for intraretinal fluid (IRF) and pigment epithelial detachment (PED) on the AROI dataset, respectively.

End-to-end learned image compression codecs have notably emerged in recent years. These codecs have demonstrated superiority over conventional methods, showcasing remarkable flexibility and adaptability across diverse data domains while supporting new distortion losses. Despite challenges such as computational complexity, learned image compression methods inherently align with learning-based data processing and analytic pipelines due to their well-suited internal representations. The concept of Video Coding for Machines has garnered significant attention from both academic researchers and industry practitioners. This concept reflects the growing need to integrate data compression with computer vision applications. In light of these developments, we present a comprehensive survey and review of lossy image compression methods. Additionally, we provide a concise overview of two prominent international standards, MPEG Video Coding for Machines and JPEG AI. These standards are designed to bridge the gap between data compression and computer vision, catering to practical industry use cases.

Integrating optical coherence tomography (OCT) into the pre-surgical stage of cataract management holds significant clinical and economic potential, particularly in low-to-middle-income countries like Kazakhstan. This study aimed to evaluate these impacts by prospectively recruiting 124 patients, aged 70±8 years, from two ophthalmology surgical centers in Almaty, Kazakhstan. Patients undergoing phacoemulsification of cataracts with monofocal intraocular lens (IOL) implantation between January and December 2022 were divided into two groups: the OCT group (n=75) received pre-operative OCT, while the Control group (n=49) did not. Visual acuity (VA) was measured pre- and post-surgery, and the cost-effectiveness of the surgical strategies was analyzed. The OCT group experienced a significantly greater improvement in VA (-0.647±0.232 logMAR) compared to the Control group (-0.543±0.244 logMAR), with a notable interaction between time and group (F(df) = 217.2, p &lt; 0.001). Additionally, pre-existing concomitant diseases were diagnosed in 25.3% of cases in the OCT group and 28.6% in the Control group. The economic analysis revealed that the integration of OCT facilitated multiple surgeries in one appointment, thereby reducing overall costs. These findings suggest that implementing OCT in the pre-surgical stage of cataract management can significantly enhance visual outcomes and decrease the cost of ophthalmology services in Kazakhstan.

Background: SARS-CoV-2 infection has spread to over 200 countries since it was first reported in December of 2019. Significant country-specific variations in infection and mortality rate have been noted. Although country-specific differences in public health response have had a large impact on infection rate control, it is currently unclear as to whether evolution of the virus itself has also contributed to variations in infection and mortality rate. Previous studies on SARS-CoV-2 mutations were based on the analysis of ~ 160 SARS-CoV-2 sequences available until mid-February 2020.^{2, 3, 4, 5} By mid-April, > 550 SARS-CoV-2 sequences had been deposited in GenBank, and over 8,200 in the GISAID database. Methods: We performed a sequence analysis on 474 SARS-CoV-2 genomes submitted to GenBank up to April 11, 2020 by multiple alignment using Map to a Reference Assembly and Variants/SNP identification. The results were verified on a larger scale, 8,126 hCoV-19 (SARS-CoV-2) sequences from GISAID database. Results: We identified 5 recently emerged mutations in many isolates (up to 40%). Our analysis highlights 5 frequent new mutations that have emerged since late February 2020. These mutations are: one each missense (non-synonymous) mutation in orf1ab (C1059T), orf3 (G25563T) and orf8 (C27964T), one in 5’UTR (C241T), one in a non-coding region (G29553A). The final mutation (G29553A) was found to be almost exclusive to the US isolates. The first 3 mutations are non-synonymous, leading to amino acid substitutions in the viral protein sequence. Except for C241T, all the novel mutations identified are absent in the isolates from Italy and Spain in the SARS-CoV-2 genomes deposited in GenBank and GISAID by April 13, 2020. Conclusion: The results of current study indicate that new mutations are emerging as COVID-19 pandemic are spreading to different countries and that geography specific mutants may exist. The findings of current study lay the foundation for further investigation into the impact of SARS-CoV-2 mutations on disease incidence, severity, and host immune response. In addition, it may also provide insights into vaccine development and serological response detection for the virus.

The article is devoted to the research of economic cycles and crises, which are studied within the framework of the theory of long waves by N. D. Kondratiev (K-waves) using the mathematical apparatus of fractional calculus. The object of the study is the mathematical model of S.V. Dubovsky 3 and some of its modifications, which describe the dynamics of the economic system, characterizing the interaction between the efficiency of new technologies and the efficiency of capital productivity. Modifications in the model are determined by the following points: the mathematical model takes into account the dependence of the rate of accumulation on capital productivity, there is an external harmonic influence - the influx of investments and new technological solutions, the economic system has heredity, including time-dependent, which leads to a delayed effect - the system’s response to impact. The property of heredity in the mathematical model is taken into account using fractional derivatives of constant and variable orders. Mathematical model S.V. Dubovsky and its modifications are studied numerically using the Adams-Bashforth-Moulton algorithm. Oscillograms and phase trajectories are constructed, and an interpretation of the simulation results is given.

We aimed to reveal the disease burden of aphasia after acute ischemic stroke (AIS) at the national level and investigate the impact of aphasia on tertiary care resources and patient outcomes. The local database from the Cluj-Napoca Emergency County Hospital (CNECH), the second largest stroke center in Romania was used to export demographics, baseline clinical and laboratory data, inpatient length of stay (LOS), NIH Stroke Scale (NIHSS), and discharge modified Rankin Scale (mRS) score data for all AIS patients admitted during March 2019. Of 92 patients included in the study, 30 (32.6 %) had aphasia on admission. In a marginally significant unadjusted hierarchical multiple regression model, individuals with aphasia had a LOS of 1.86 days longer than stroke survivors without aphasia. In an adjusted version of the model, the NIHSS score at baseline was a significant predictor for LOS. In addition, the presence of aphasia was associated with a 1.49 increase in the mean mRS score. Aphasia was a marginally significant predictor for increased LOS. Presence of aphasia was more likely to produce a poor functional outcome. Considering an estimated impact of approximately EUR 3 million on direct medical expenditure annually, future policymaking efforts should improve prevention of stroke and improved access to post-stroke aphasia care in Romania.

(1) Background: Premature infants require mothers’ milk fortification to meet nutrition needs, but breast milk composition may be variable leading to a risk of inadequate nutrition. We aimed at determining factors influencing mothers’ milk macronutrients. (2) Methods: Milk samples were analyzed for the first 5 weeks after premature delivery, by infrared spectroscopy. Mothers’ nutritional intake data were obtained during standardized interviews with dieticians then analyzed with reference software. (3) Results: Composition of 367 milk samples from 81 mothers was (Median [range]g/100mL): Carbohydrates 6.8[4.4-7.3], lipids 3.4[1.3-6.4], proteins 1.3[0.1-3.1]. There was a relationship of milk composition with mothers’ carbohydrates intake only (r=0.164; p<.01). Postnatal age was correlated with milk proteins (r=-0.505 p<.001) & carbohydrates (r=+0.202, p<.001). Multiple linear regression analyses showed (coefficient) a relationship between milk proteins r=0.547 and postnatal age (-0.028), carbohydrates intake (+0.449) and the absence of maturation (-0.066); and between milk lipids r=0.295 and carbohydrates intake (+1.279) and smoking (-0.557). Finally, between milk carbohydrates concentration r=0.266 and postnatal age (+0.012) and smoking (-0.167). (4) Conclusions: Variability of mothers’ milk composition is differentially associated for each macronutrient with maternal carbohydrates intake, antenatal steroids, smoking, and postnatal age. Improvement in milk composition could be achieved by modification of these related factors.

Total hip arthroplasty (THA) is one of the most successful orthopedic procedures and is highly effective in improving function and quality of life. However, after discharge patients commonly experience edema, which can lead to health consequences and lower quality of life. For these rea-sons, the aim of this study is to evaluate the effectiveness of a specific intermittent leg pneumatic compression on lower limb edema and physical outcomes in patients after total hip arthroplasty, compared to standard conservative treatment. A total of 47 patients were enrolled and randomly allocated into two groups: the pneumatic compression group (PG=24) and the control group (CG=23). We evaluated thigh and calf circumferences, knee and ankle range of motion, pain and walking autonomy. Our results showed a greater reduction in thigh and calf circumference for PG (p<0.001), while other outcomes were similar for the two groups (p>0.05). The combination of standard therapy with pneumatic leg compression was more effective in reducing lower limb edema, thigh, and calf circumferences compared to the use of standard treatment. Our results suggest that pressotherapy treatment is a valuable and efficient option for managing lower limb edema and preventing VTE after THA.

The problems of modeling the human bladder and its stress-strain state under external static influence were considered. A method for identification of the anisotropic biomechanical characteristics of bladder tissue was proposed. A FEM model was created, which accepts into regard that the bladder is surrounded by fiber and affected by surrounding organs, and partially protected by pelvic bones. The model considered the presence of constant hydrostatic pressure on the walls of the bladder when it is full. It has been shown that isotropic mechanical characteristics of biological tissue can be used for studying the deformed state of a filled bladder if the filled bladder 300 ml is considered as initial non-deformed stage. This was shown by modeling and verification the effect of the external static force on the bladder. Numerical experiments were conducted based on the constructed model. To validate the results obtained, a series of natural experiments on the effect of external pressure on the bladder under ultrasound control was conducted. In the future, it is planned to use the constructed model to study rupture deformations of the bladder under the influence of static and dynamic loads.

Background: Scientific literature on COVID-19 is still limited about long-term impacts on the all-body systems and they treatments. The aim of the study was to create a safe protocol-based in-tervention to improve functional and equilibrium abilities in older adults impacted by COVID-19. Methods: The study completed 46 people (intervention group: n=26; control group: n=20). Re-sistance training (RT) was held twice a week, 60 min per session for 8 weeks. The postural stability and quality of life questionnaire (WHQOOL) were conducted during pre- and post-testing. Results: Results indicated significant differences in overall stability index (OSI) with eyes open (EO), ante-rior-posterior stability index (APSI) EO, fall risk index 6-2 (FRI6-2) values in males (p

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice

To study the feasibility and effect of compounding lignin and its derivatives to improve expansive soil, the physical properties, mechanical properties, and microstructure of the improved soil mixed with calcium lignosulfonate alone, calcium lignosulfonate and lignin fibers were investigated through indoor experiments and electron microscope scanning. Select samples with better performance for water stability tests, and discuss the improvement mechanism of expansive soil by combining macroscopic mechanical changes with microstructural characteristics. The research results show that the addition of calcium lignosulfonate can reduce the water content of the soil and enhance its strength of the soil. The overall performance is the best when the calcium lignosulfonate content is 3%. 3% calcium lignosulfonate compounded with 1.5% lignin fiber has the best all-around performance; the composite improved soil has a better pore-filling effect, the whole is more compact, and the connection between particles significantly enhances the strength, which greatly inhibits the development of cracks good water stability. Lignin and its derivatives compound improved expansive soil have better effect than traditional improvement methods, and have no pollution to the environment, which can provide a particular reference for engineering practice.

The primary therapeutic method for correcting hyperglycemia today is diet therapy. Lipids are not only a source of nutrients but can also act as initiators of adipocyte differentiation in the fetus, which explains the development of fetal macrosomia and future metabolic disorders in children born to mothers with gestational diabetes mellitus (GDM). Changes in the profile of circulating lipids in the maternal bloodstream, depending on adherence to a rational diet among mothers with GDM and the development of fetal macrosomia, is a complex and not fully understood process. The aim of the study was to examine the characteristics of the lipid profile in the blood plasma of pregnant women with GDM in all trimesters of pregnancy based on adherence to diet therapy. The design of the clinical part of the work was carried out within the framework of a 'case-control' study.The study included 110 women, 80 of whom were in the control group, 20 in the group with GDM adhering to the diet, and 10 in the group with GDM not adhering to the diet. The laboratory part was conducted as part of a longitudinal dynamic study with venous blood samples taken at three points: 11-13, 24-26, and 30-32 weeks of pregnancy.A significant impact of diet therapy on the blood lipid composition throughout pregnancy was demonstrated, starting as early as the first trimester. ROC analysis showed high effectiveness of the developed models with an AUC of 0.98 for the "30-32 weeks" model, with sensitivity and specificity of 1 and 0.9, respectively. An association was found between diet, maternal blood lipid composition at 32 weeks of pregnancy, and newborn weight. The direction of changes in the lipid spectrum during the development of macrosomia and diet therapy is diametrically opposed. This confirms at the molecular level that diet therapy can normalize not only carbohydrate but also lipid metabolism in the mother and fetus. Based on the obtained data, it can be suggested that after validation, the developed models could be used to refine the prognosis of macrosomia development based on the lipid profile of blood plasma at different stages of pregnancy.

The ever deepening population aging has brought opportunities and challenges to the continued expansion of tourism consumption in China. In this article, the impact of population aging on household tourism consumption was studied from both theoretical and empirical aspects. First, the micro mechanisms of the impact of population aging on household tourism consumption were analyzed, which include economic condition mechanism, intergenerational care mechanism, health status mechanism and Internet use mechanism. Subsequently, the impact of population aging on household tourism consumption and its impact mechanisms were tested, and the heterogeneity analysis was conducted, by using the data of China Family Panel Studies (CFPS) from 2014, 2016 and 2018. The main conclusions of the article are as follows: (1) Population aging has a significant negative impact on household tourism consumption, and a series of robustness test results such as endogenous treatment support this finding. (2) The results of the impact mechanism test show that population aging has a negative mediating effect on household tourism consumption by reducing household economic conditions. The moderating effect of intergenerational care on the effect of population aging on household tourism consumption is insignificant. Health status of the elderly and Internet use have a significant positive moderating effect on the impact of population aging on household tourism consumption. (3) The results of the heterogeneity analysis show that the negative impact of population aging on household tourism consumption in urban areas is greater than that in rural areas, and the negative impact of population aging on household tourism consumption of families with the old-old elderly is greater than that of falimies with the young-old elderly. The conclusions of this article provide important references for activating tourism consumption in China in the context of population aging.

The increasing residential space differentiation is an important practical problem for Chinese cities. The different choice of living space for urban residents is a concrete reflection of social class divide, which reflects the differences in the choices and demands of different social groups for urban housing. Taking Wuhan, an important city in central China, as an example, this research divides the residential space based on the social resource structure, and analyzes and compares the spatial differentiation and influencing factors of different residential areas and houses with different prices in Wuhan by spatial differentiation indicators and geographic detector. The results show clear differences in resource structure among residential areas, and there are few high-quality residential areas with a concentrated distribution. The spatial differentiation levels of different residential areas are distinct, and the pursuit of high-quality and scarce resources is the key to the residential space differentiation of most large cities in China. In addition, residential space differentiation can lead to inter-generational problems such as housing wealth inequality, resource deprivation and solidified class identity. Exploring the mechanisms and social effect of residential space differentiation in most large cities in China can provide some reference for China's urban space planning and real estate market regulation in the new era.

Sustaining learners’ motivation to keep learning has been concerned for over 60 years in education and SLA. Most research focusing on Japanese university students has contributed lots of theoretical and practical developments, but research focusing on motivations of non-traditional adult learners and those under 18-year-old to learn Chinese is still little even though previous research findings have proved age is one of the key variables influencing learning besides nationalities and Chinese language levels. In order to find an effective treatment for sustainable Chinese language learning in Japan, this study utilized a survey method to analyze the types of Japanese learners’ motivation to learn Chinese via analysis of a moment structures (AMOS), and to compare the differences of the motivation via one-way ANOVA. This study revealed that Japanese learners’ motivation to learn Chinese consists of eight common types, which are “instrumental motivation”, “personal orientation”, “identified regulation”, “Chinese cultural productions”, “integrating into Chinese community”, “external regulation”, “social responsibility”, and “Chinese for academic purposes”. Also, there are similarities and differences existing in the eight motivation types among the Japanese children, adolescents, (non-) traditional adult learners of Chinese as a foreign language (CFL). The findings contribute the understanding of motivation types and differences among the four aged Japanese learners to teachers of teaching Chinese to speakers of other languages (TCSOL), and to future research further exploring how differently aged Japanese learners can have and use a higher motivation as a main drive to learn Chinese language as a lifelong business.

Antiviral therapy such as Oseltamivir has been recommended for hospitalized children with suspected and confirmed influenza for almost 20 years. The therapy is officially authorized for newborns two weeks of age or older, however, questions about its safety and effectiveness still surround it. Our goal was to assess the epidemiological features of two consecutive seasonal in-fluenza cases in children following the COVID-19 pandemic and also to observe the clinical ef-fectiveness and tolerability of oseltamivir in hospitalized children who were not vaccinated against influenza and who had different influenza subtypes, including A (H1N1), A (H3N2), and influenza B, and to identify specific comorbidities associated with influenza in children. We performed an observational study on 1300 children, enrolled between 1st October 2022 and 30th May 2023 and 1st October 2023-4th of May 2024, to the IX Pediatric Infectious Diseases Clinical Section of the National Institute of Infectious Diseases "Prof. Dr. Matei Balș". During the 2022-2023 influenza sea-son, 791 pediatric patients tested positive for influenza and received Oseltamivir. Of these, 89% (704/791) had influenza A, with 86.4% subtypes A(H1N1) and 13.6% of cases had A(H3N2), and influ-enza B 11%(87/791) pediatric patients. Of the total group, 59% were male, and the median age was 2,4 years (1.02-9.28). For the 2023-2024 influenza season, 509 pediatric patients tested positive for influen-za, 56.9% were male gender and were treated with Oseltamivir. 81.6 % had Influenza A, and 18.4% had influenza B. Treatment with neuraminidase inhibitors like Oseltamivir, 2mg/kg/dose twice daily for 5 days, was well tolerated by the children, and we recorded no deaths. The duration of fever hospitaliza-tion after the Oseltamivir administration was significantly longer for patients with A(H1N1) infection than A(H3N2), during both seasons. We identified more complications in the 2022-2023 season and a decreasing number of Influenza B for the 2023-2024 season. Among children with comorbidities, the most common were asthma, gastrointestinal disorders, and metabolic and endocrine diseases. In terms of effectiveness, oseltamivir significantly reduced the intensity of influenza symptoms, thus reducing the number of days of hospitalization (p=0.001) as well as post-infection complications (p=0.005) in both groups. Oseltamivir was less effective in Influenza A (H1N1) than A(H3N2), (p=0.0035). In this study, we evaluated the clinical effectiveness of oseltamivir therapy for all influenza types/subtypes in children, and the length of hospitalization. We identified comorbidities associated with prolonged dura-tion of hospitalisation. Influenza vaccination should be the main tool in the prevention of influenza and its complications in children, especially with comorbidities.

The thermal degradation of brakes has a significant impact on the stability of pure electric commercial vehicles during long downhill braking. Based on road slope and using fuzzy control method, design strategies for motor regenerative braking force and friction braking force distribution, with the aim of reducing friction braking force, improving braking stability, and recovering braking energy. By establishing driving conditions on roads with different slopes and using numerical analysis methods to verify the proposed control strategy. the results show that under the 6% constant slope driving condition, the vehicle maintains a constant speed of 30km/h downhill driving, and the braking energy recovery rate reaches 50.93%; Under the condition of 3% -6% gradient driving, the vehicle speed fluctuates slightly, but it can still be maintained at a constant speed of 30km/h for downhill driving through the adjustment of the motor's reverse drag characteristic, with a braking energy recovery rate of 49.97%; During the process of driving downhill at a constant speed, the frictional braking force does not participate in braking; The braking energy recovery rate is determined by the slope and braking deceleration.

The COVID-19 pandemic has underscored the intricate interplay between viral infections and opportunistic bacterial pathogens such as Klebsiella pneumoniae. K. pneumoniae harbors various antibiotic resistance determinants like extended-spectrum and plasmid-mediated AmpC β-lactamases and carbapenemases. In the two years following the pandemic, carbapenemase producing K. pneumoniae isolates obtained routinely in outpatient and inpatient setting demonstrated similar resistance patterns which prompted research. The aim was to compare and subsequently analyze carbapenem-resistant hospital and outpatient’s K. pneumoniae isolates’ resistance mechanisms, traits and molecular epidemiology, following the COVID-19 pandemic. Disk diffusion and broth dilution method were the methods of choice to determine antibiotic susceptibility. β-lactamases were screened by phenotypic methods and confirmed with PCR. In total 113 isolates were analysed. Resistance to amoxicillin-clavulanate and ertapenem was confirmed in all strains. High resistance rates (over 90%) were observed for extended-spectrum cephalosporins, and ciprofloxacin. OKNV testing and PCR detected OXA-48 in 106, NDM in 7 and KPC in only one isolate. ESBLs accompanied carbapenemases in 103 isolates. Carbapenem resistance in K. pneumoniae is becoming a global problem, hence careful monitoring of its resistance traits is of utmost importance in order to combat the arising threat. OXA-48 seems to continue predominating in the turbulent period after pandemic.

(1) Background: Sarcopenia, a condition characterized by a decrease in muscle mass and strength, is very common in patients with obesity and can be aggravated by bariatric surgery, potentially compromising the clinical results of surgery. There is increasing interest in pa-tient-reported outcome measures (PROMs) to assess results in other health variables that may be especially important for individual patients. The role of exercise in enhancing health-related quality of life (HRQoL) after surgery remains underexplored. This study investigated the impact of exercise on HRQoL in bariatric sarcopenic patients via the Sarcopenia Quality of Life (SarQoL) questionnaire. (2) Method: Candidates for surgery took part in the EXPOBAR program and were randomized into experimental and control groups. The intervention lasted 16 weeks, starting one month after surgery, and included combined aerobic and resistance exercise. Outcomes, including body composition and physical fitness parameters, were measured before and after the intervention. All participants underwent gastric bypass surgery (RYGB). (3) Results: The baseline characteristics of the participants were not significantly different between the two groups. All patients met the criteria for moderate/severe obesity and the EASO/ESPEN criteria for sarcopenia, namely, reduced muscle strength assessed by grip strength and reduced muscle mass assessed by the ASMM score/weight. After completing the study protocol, patients in both groups had increased HRQoL, but the increase was significantly greater in the intervention group than in the control group. (4) Conclusion: Our findings suggest that exercise plays a crucial role in improving both physical and psychological well-being in postbariatric patients, highlighting the need to integrate structured exercise programs in post-surgery care. This study was prospectively registered at Clinicaltrials.gov (NCT03497546).

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

Objective We aim to assess the quality of life for women with genitourinary fistulas before and after surgery, utilizing the WHOQOL-BREF questionnaire to contrast the preoperative and postoperative results. Materials and Methods: This quasi-experimental study was conducted at the Department of Urology, SIUT, Karachi, Pakistan, from January to December 2023. We used the WHOQOL-BREF questionnaire to assess the quality of life. Participants completed the questionnaire both before the surgical intervention and three months after successful fistula repair. The collected data were entered and analysed using IBM SPSS v26, with a significance level set at p≤ 0.05. Results The participants had a mean age of 35.50 years, with a standard deviation of 8.87 years. Before undergoing genitourinary fistula repair, the average WHOQOL-BREF score was 12.17 with a standard deviation of 5.77. Following the repair, the mean score showed a significant improvement, rising to 96.67 with a standard deviation of 11.86. This marked improvement was statistically significant, with a p-value of 0.0001. Conclusion This study concludes that genitourinary fistula repair at our tertiary care hospital significantly and positively impacts patients' quality of life. The findings emphasize the critical role of timely and appropriate surgical intervention in improving overall well-being. Continued comprehensive care and support are vital for these patients' holistic recovery and long-term health.

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

The new hybrid composite materials for PEM fuel cell were synthesized by UV-polymerization of acrylic monomers (acrylonitrile (AN), acrylic acid (AA), ethylene glycol dimethacrylate (EGDMA)) and sulfo aromatic monomer – sodium styrene sulfonate (SSS), and tetraethoxysilane/3-methacryloxypropyltrimethoxysilane (TEOS/MAPTMS)-based sol-gel system. By means of X-ray spectroscopy fractal structure of the obtained materials was characterized. Proton conductivity and viscoelastic properties of the materials were investigated depending on the content of inorganic component in nanocomposites. On the basis of impedance studies, an equivalent scheme is proposed that successfully describes the proton conductivity in the synthesized composite electrolyte membranes.

This paper investigates the evolution of microstructures and precipitations of an ultra-low iron alloy 625 subjected to long term aging treatment by scanning electron microscope (SEM) and X-ray diffraction(XRD). Use ASTM G28A acid Fe3(SO4)2 erosion to represent intergranular corrosion weightlessness and corrosive morphology. The result shows that alloy at 750C by aging treatment for 40h, precipitated γ'' phase in the grain boundary. In high density area of γ'' phase, occurs γ'' phase to δ phase degeneration transformation by aging treatment for 200h and the needle-like δ phase becomes more with time prolonged. And γ'' phase degenerated to δ phase completely until treated for 1000h. The sample which has aging treatment tends to have intergranular corrosion and mainly because alloy element spreading leads to dilution area and grain boundary precipitated phase, plus interlaced δ phase’s dissolving, which makes sample grain particle fall off and this results in apparent weightlessness. The weightlessness rate(WLR) is related with precipitated volume score. With aging sensitization time change, can be described by Johnson-Mehl-Avrami equation, i.e.: $WLR=44.32\left[1-\text{exp}\left(-\frac{t}{10.99}\right)\right]+44.62\left[1-\text{exp}\left(-\frac{t}{327.8}\right)\right]+1.267\left(mm/a\right)$

Identifying dust aerosols from passive satellite images is of great interest for many applications. In this study, we developed 5 different machine-learning (ML) and deep-learning (DL) based algorithms, including Logistic Regression, K Nearest Neighbor, Random Forest (RF), Feed Forward Neural Network (FFNN), and Convolutional Neural Network (CNN), to identify dust aerosols in the daytime satellite images from the Visible Infrared Imaging Radiometer Suite (VIIRS) under cloud-free conditions on a global scale. In order to train the ML and DL algorithms, we collocated the state-of-the-art dust detection product from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) with the VIIRS observations along the CALIOP track. The 16 VIIRS M-band observations with the center wavelength ranging from deep blue to thermal infrared, together with solar-viewing geometries and pixel time and locations, are used as the predictor variables. Four different sets of training input data are constructed based on different combinations of VIIRS pixel and predictor variables. The validation and comparison results based on the collocated CALIOP data indicates that the FFNN method based on all available predictor variables is the best performing one among all methods. It has an averaged dust detection accuracy of about 81 %, 89 % and 85 % over land, ocean and whole globe, respectively, compared with collocated CALIOP. When applied to off-track VIIRS pixels, the FFNN method retrieves geographical distributions of dust that are in good agreement with on-track results as well as CALIOP statistics. For further evaluation, we compared our results based on the ML and DL algorithms to NOAA’s Aerosol Detection Product (ADP) , which is a product that classifies dust, smoke and ash using physical-based methods. The comparison reveals both similarity and differences. Overall, this study demonstrates the great potential of ML and DL methods for dust detection and proves that these methods can be trained on the CALIOP track and then applied to the whole granule of VIIRS granule.

Obesity represents a worldwide epidemic disorder, increasing the overall morbidity and mortality rate. In this study we investigated the impact of obesity on peri-operative and long-term functional outcomes of Robotic assisted simple prostatectomy (RASP). Baseline flowmetry parameters and validated questionnaires’ scores were prospectively recorded. Follow-up assessments included Flowmetry and validated questionnaires. Composite outcomes (Trifecta) was defined as combination of: post-operative Q-max>15 ml/sec, IPSS score<8 and absence of complications. Pentafecta included also post-operative ejaculation persistence (MSHQ score>0) and the Erectile function maintenance (∆IEEF<6). Data were stratified by BMI (<30 or ≥30). 81 patients underwent RASP in our Institution. Baseline demographics and clinical features, questionnaires score and baseline flowmetry results were comparable between obese and non-obese cohorts. At follow-up, obese patients reported lower subjective improvement in IPSS (p=0.02) and OABQ scores (p<0.001) and higher incidence of stress incontinence requiring Duloxetin (p<0.001). Flowmetry outcomes, were also worse in this cohort (p=0.02 and p=0.03, respectively). At comprehensive outcomes assessment, obese patients had comparable Trifecta (67% vs 54%, p=0.39) and pentafecta achievement rate (p=0.76). Our prelimirary results proved that obesity is associated with worse functional outcomes (storage LUTS and incontinence rate) after RASP, but doesn’t affect trifecta and pentafecta achievement rate.

Background: Modern MEG devices include 102 sensor triplets containing one magnetometer and two planar gradiometers. The first processing step is often a signal space separation (SSS), which provides a powerful noise reduction. A question commonly raised by researchers and reviewers is which data should be employed in source reconstruction: (1) magnetometers only, (2) gradiometers only, (3) magnetometers and gradiometers together. The MEG community is currently divided about the proper answer and strong arguments in favor and against these three approaches often expressed. Methods: First, we provide theoretical evidence that both gradiometers and magnetometers contain the same information after SSS, and argue that they both result from the backprojection of the same SSS components. Then, we compare beamforming source reconstructions from magnetometers and gradiometers in real MEG recordings before and after SSS. Results: Without SSS, the correlation between source time series extracted from magnetometers and gradiometers was high, with Pearson correlation coefficient r=0.5-0.8. After SSS, these correlation values increased dramatically, reaching over 0.90 across all cortical areas. Conclusions: After SSS, almost identical source reconstructions (r>0.9) can be obtained with magnetometers and gradiometers, as long as regularization is selected appropriately to account for the different properties in magnetometers and gradiometers covariance matrices.

This paper identifies a dilemma in the relationship between R^2 and price efficiency: After comprehensively studying the R^2 change around 7 well-known corporate events, neither the traditional understanding of R^2 as price inefficiency, nor the behavioral way of R^2 as price efficiency can explain the observed R^2 change around the events. We adopt an alternative methodology to replace the standard difference-in-difference regression and directly decompose the R^2 change. We find that, due to the endogeneity of events, the changes of R^2 are over-estimated. We further propose that in the event study setting, the R^2 change may be simply the consequence of the inflow/outflow of some trend-chasing investors, and it may be detached from price (in) efficiency. Empirical evidences are consistent with this hypothesis.

Until recently, no disease-specific health-related quality of life (HRQoL) instrument existed for pediatric traumatic brain injury (TBI). In this revalidation study, the psychometric properties and the validity of the final German version of the 35-item QOLIBRI-KID/ADO questionnaire were examined in 300 children and adolescents. It is the first self-reported TBI-specific instrument for measuring pediatric HRQoL in individuals aged 8–17 years. The six-factor model fits the data adequately. Internal consistencies were excellent for the total score and satisfactory to excellent for the scale scores. Intraclass correlations indicated good test-retest reliability. Construct validity was supported by overlaps between the QOLBRI-KID/ADO and the PedsQL, which measures generic HRQoL. Discriminant validity indicated that HRQoL was significantly lower in older children and girls, and in those with anxiety, depression, and post-concussion symptoms than in comparison groups, replicating the results of the questionnaire’s first development study. Our results suggest that the QOLIBRI-KID/ADO is a valid and reliable multidimensional instrument for assessing disease-specific HRQoL after pediatric TBI in clinical and research settings, which can additionally be used across the lifespan in combination with the adult version. This may help to improve care, treatment, daily functioning and HRQoL after TBI.

Embryologically, the left brachiocephalic vein (LBV) originates as an anastomotic channel between the right and left anterior cardinal veins 1 . This positions the LBV between the manubrium sterni anteriorly and the innominate artery posteriorly 2 . This pattern of adjacency of the aorta to the LBV is unique to mammals and results from a quirk of evolution 3 . With age, the ascending aorta unfolds, elongates and dilates 4 . Simultaneously, there is a change in the thoracic geometry that reduces the thoracic volume primarily from disc height loss and kyphosis 5 . These transitions progressively compress the LBV. Normally this compression is circumvented via collateral pathways and "Blood finds a way" 6 . However, traversing these circuitous pathways comes at a cost and can result in delayed transit times and venous congestion. While it is possible that compression of the LBV in the setting of adequate collateral channels may fail to provoke any pathologic sequelae, we propose a phenomenon in which such compression in the setting of inadequate collateral circulation may lead to a state of pathologic venous congestion. This anatomic anomaly and its associated clinical features, if identified, can offer a new avenue for treatment options for some of the hitherto unexplained neurologic disorders.

Materials characterised by magnetorheological properties are non-classic engineering materials. A significant increase in the interest of scientific community in materials from this group can be observed over the recent several years. The results of research presented in this article are oriented on the examination of said materials’ mechanical properties. In order to do so, stress relaxation tests were conducted on cylindrical samples of magnetorheological elastomers loaded with compressive stress for various values of magnetic induction (B1 = 0 mT, B2 = 32 mT, B3 = 48 mT, and B4 = 64 mT) and temperature (T1 = 25° C, T2 = 30° C, and T3 = 40° C). The results of these tests indicate that the stiffness of examined samples increases along with the increase of magnetic field induction and decreases along with the increase of temperature. On this basis, it has been determined that: the biggest stress amplitude change caused by the influence of magnetic field was σ0ΔB = 12.7% and the biggest stress amplitude change caused by the influence of temperature was σ0ΔT = 11.3%. As a result of applying a mathematical model, it has been indicated that the stress relaxation in the examined magnetorheological elastomer for the adopted time range (t = 3600 s) has a hyperbolic decline nature. The collected test results point to examined materials being characterised by extensive rheological properties, which leads to a conclusion that it is necessary to conduct further tests in this scope.

In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

Undernutrition and micronutrient deficiencies such as anemia are considered significant public health challenges in Bangladesh, which enhancing fish consumption is a well-established food-based intervention to address these. This paper documents the establishment of community-based fish chutney production and reports the impact of its consumption on mid-upper arm circumference (MUAC) and hemoglobin (Hb) levels among targeted 150 pregnant and lactating women (PLW) in rural Bangladesh. A fish chutney was developed using locally available ingredients followed by a series of laboratory tests, including nutrient composition, shelf-life and food safety. A community-based fish chutney production process was designed to: 1) supply locally available ingredients for processing; 2) establish two fish drying sites; 3) initiate a community-based production site, and 4) distribute fish chutney to PLW by six women nutrition field facilitators for one year. Then a pre- and post-intervention study was designed for a selected 150 PLW to receive 30g of fish chutney daily for 12 months. Differences in mean mid-upper arm circumference (MUAC) and hemoglobin (Hb) levels pre- and post-consumption were analyzed using one-way analysis of variance. Consumption of 30g of fish-chutney resulted in significant increases of the mean values of Hb levels and MUAC among the targeted PLW.

This paper investigates the critical factors for balancing environmental sustainability and economic development through the lens of New Structural Economics. Specifically, we utilize the congruence index to access the alignment between local factor endowment structure and firm production input structure. Using a comprehensive manufacturing firm-level pollutant emissions dataset from the Yangtze River Economic Belt (YEB) region in China, we find that firms demonstrating higher congruence exhibit improved economic performance and alignment with comparative advantages. This not only contributes to increased economic efficiency for these firms but also leads to a reduction in pollutant emissions, including wastewater discharge and Chemical Oxygen Demand (COD) emissions. Our study provides valuable insights into achieving mutually beneficial environmental and economic outcomes.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Background: This study investigates microvascular changes in the dermis and muscle following a balneotherapy regimen prescribed by therapeutic protocols. Methods: Thirty-five inpatients participated in a two-week balneal course involving the application of mud and hypersaline water. Mud was applied outdoors in the summer as cold mud ointment and indoors year-round as mud packs or mud baths alternated with hypersaline water baths. Biopsies of the skin and muscle were obtained twenty-four hours post-discharge and prepared histologically. Results: Analysis focused on the epidermis, dermis, and muscle. Microvascular changes observed included increased caliber and number of open capillaries, as well as the presence of angiogenesis vessels. Statistical analysis showed significant differences in angiogenesis vessels between cold mud ointment and mud pack treatments compared to control and mud bath groups. A higher number of angiogenesis vessels were observed in the dermis in the mud pack group and in the muscle with mud cold ointment. Repeated thermal stimulation with mud and hypersaline water over two weeks produced histologically evident tissue modifications, persisting in the dermis and muscle at least twenty-four hours post-treatment completion.

Patients with metastatic epidural spinal cord compression (MESCC) and favorable survival prognoses may benefit from radiation doses exceeding 10 x 3.0 Gy. In a multi-center phase 2 trial, patients receiving 15 x 2.633 Gy (41.6 Gy10) or 18 x 2.333 Gy (43.2 Gy10) were evaluated for local progression-free survival (LPFS), motor/sensory functions, ambulatory status, pain, distress, toxicity, and overall survival (OS). They were compared (propensity score adjusted Cox regression) to a historical control group (N=266) receiving 10 x 3.0 Gy (32.5 Gy10). In the phase 2-cohort, 50 (of 62 planned) patients were evaluable for LPFS. Twelve-month rates of LPFS and OS were 96.8% and 69.9%, respectively. Motor and sensory functions improved in 56% and 57.1% of patients, and 94.0% were ambulatory following radiotherapy. Pain and distress decreased in 84.4% and 78.0% of patients. Ten and two patients experienced grade 2 and 3 toxicities, respectively. Phase 2 patients showed significantly better LPFS than the control group (p = 0.039) and a trend for improved motor function (p = 0.057). Ambulatory and OS rates were not significantly different. Radiotherapy with 15 x 2.633 Gy or 18 x 2.333 Gy was well tolerated and appeared superior to 10 x 3.0 Gy.

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

Coronary no-reflow (CNR) is a frequent phenomenon that develops in patients with ST-segment elevation myocardial infarction (STEMI) following reperfusion therapy. CNR is highly dynamic and develops gradually (over hours) and persists for days to weeks after reperfusion. Microvascular obstruction (MVO) developing as a consequence of myocardial ischemia, distal embolization and reperfusion-related injury is the main pathophysiological mechanism of CNR. The frequency of CNR or MVO after primary PCI differs widely depending on the sensitivity of the tools used for diagnosis and timing of examination. Coronary angiography is readily available and most convenient to diagnose CNR but it is highly conservative and underestimates the true frequency of CNR. Cardiac magnetic resonance (CMR) imaging is the most sensitive method to diagnose MVO and CNR that provides information on the presence, localization and extent of MVO. CMR imaging detects intramyocardial hemorrhage and accurately estimates the infract size. MVO and CNR markedly negate the benefits of reperfusion therapy and contribute to poor clinical outcomes including adverse remodeling of left ventricle, worsening or new congestive heart failure and reduced survival. Despite extensive research and the use of therapies that target almost all known pathophysiological mechanisms of CNR, no therapy has been found that prevents or reverses CNR and provides consistent clinical benefit in patients with STEMI undergoing reperfusion. Currently the prevention or alleviation of MVO and CNR remain unmet goals in the therapy of STEMI that continue to be under intense research.

ABSTRACT: Waterlogging is a common abiotic stress in global maize production. Maize flowering stage (from tasseling to silking) is more fragile to environmental stresses among different growth stages. The effects of waterlogging at flowering stage on the grain yield and starch quality of waxy maize were studied using Suyunuo5 (SYN5) and Yunuo7 (YN7). The grain yield and starch concentration of both hybrids were reduced by waterlogging. The size of starch granules and proportion of small-molecule amylopectin increased in SYN5 and decreased in YN7 when plants suffered waterlogging at flowering, in contrast to the change trend of relative crystallinity. The pasting viscosities and gelatinization temperatures were reduced, whereas the gelatinization enthalpy was unaffected by waterlogging in both hybrids. Our study indicated that waterlogging at flowering reduced the grain yield, restricted starch deposition, and deteriorated the pasting property of waxy maize. Between the two hybrids, YN7 and high pasting viscosities and low retrogradation percentage than SYN5, indicated its advantages on produce starch for viscous and less retrograde food. Results provide information for utilization of waxy maize grain in food production.

On February 24, 2022 Russia started the full-scale invasion of Ukraine, which created an unprecedented number of refugees. To estimate the influence of this humanitarian disaster on the COVID-19 pandemic dynamics, the averaged daily numbers of cases and reproduction numbers in Ukraine, the UK, Poland, Germany, the Republic of Moldova, and in the whole world were calculated for the period February-April 2022. The registered numbers of cases were compared with ones calculated with the use of the generalized SIR-model and corresponding parameter identification procedure for the previous epidemic waves in Ukraine, Poland, Germany, and the world. Since before February 24, 2022 the estimation of the number of infectious persons per capita in Ukraine 3.6 times exceeded the global figure, the increase of the number the new cases and the pandemic duration was expected. In March 2022 the increase of the averaged number of new cases in the UK, Germany, and worldwide was visible. A simple formula to estimate the effective reproduction number based on the smoothed accumulated numbers of cases is proposed. The results of calculations agree with the figures presented by John Hopkins University and demonstrate a short-term growth of the reproduction number in the UK, Poland, Germany, Moldova, and worldwide in March 2022.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

Seismic velocity inversion is one of the most critical issues in the field of seismic exploration and has long been the focus of numerous experts and scholars. In recent years, the advancement of machine learning technologies has infused new vitality into the research of seismic velocity inversion and yielded a wealth of research outcomes. Typically, seismic velocity inversion based on machine learning lacks control over physical processes and interpretability. Starting from wave theory and the physical processes of seismic data acquisition, this paper proposes a method for seismic velocity model inversion based on Physical Embedding Recurrent Neural Networks. Firstly, the wave equation is a mathematical representation of the physical process of acoustic waves propagating through a medium, and the finite difference method is an effective approach to solving the wave equation. With this in mind, we introduce the architecture of recurrent neural networks to describe the finite difference solution of the wave equation, realizing the embedding of physical processes into machine learning. Secondly, in seismic data acquisition, the propagation of acoustic waves from multiple sources through the medium represents a high-dimensional causal time series (wavefield snapshots), where the influential variable is the velocity model, and the received signals are the observations of the wavefield. This forms a forward modeling process as the forward simulation of the wavefield equation, and the use of error back-propagation between observations and calculations as the velocity inversion process. Through time-lapse inversion and incorporating the causal information of wavefield propagation, the non-uniqueness issue in velocity inversion is mitigated. Through mathematical derivations and theoretical model analyses, the effectiveness and rationality of the method are demonstrated. In conjunction with simulation results for complex models, the method proposed in this paper can achieve velocity inversion in complex geological structures.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.

Gravity-aided inertial navigation system (GAINS) is an important development in autonomous underwater vehicle (AUV) navigation. An effective path planning algorithm plays an important role in the performance of navigation in long-term underwater missions. By combining the gravity information obtained at each position with the error information from the INS, the posterior Cram\'er-Rao bound (PCRB) of GAINS is derived in this paper. The PCRB is the estimated lower bound of position variance for navigation along the planned trajectory. And the sum of PCRB is used as the minimum cost from the initial state to the current state in the state space, and the position error prediction variance of inertial navigation system (INS) is used as the minimum estimated cost of the path from the current state to the goal state in the A* algorithm. Thus, a path planning method with optimal navigation accuracy is proposed. According to simulation results, traveling along the path planed by the proposed method can rapidly improve the positioning accuracy while consuming just slightly more distance. Even when measuring noise changes, the planned path can still maintain optimal positioning accuracy, and high positioning accuracy is possible for any trajectory located within a certain range of the planned path.

Wireless sensor networks are attractive largely because they need no wired infrastructure. But precisely this feature makes them energy constrained. Recent studies find that sensing behaviors that are otherwise deemed efficient consume comparable energy with communication. The duty cycle scheduling is perceived as contributing to achieving energy efficiency of sensing. Because of different research assumptions and objectives, various scheduling schemes have various emphases. This paper designed an adaptive sensing scheduling strategy. The objective function of the scheduling strategy includes minimizing average energy expenditure and maximizing sensing coverage (reducing event miss-rate), and it requires relatively loose assumptions. We determine the functional relationship between the variables of the objective function and the step-size parameters of the proposed strategy through the numerical fitting. We found that the objective function aggregated by the fitting functions is a bivariate multi-peak function that favors the Fibonacci tree optimization algorithm. Once the optimization of parameters is done, the strategy can be easily deployed and behaves consistently in the coming hours. We name the proposed strategy as “FTOS”. The experimental results show that the Fibonacci tree optimization algorithm gets a better optimistic effect than the comprehensive learning particle swarm optimization (CLPSO) algorithm and differential evolution (DE) algorithm. The FTOS strategy is superior to the fixed time scheduling strategy in achieving the scheduling objectives. It also outperforms other strategies with the same scheduling objectives such as LDAS, BS, DSS and PECAS.

The latest methods based on deep learning have achieved amazing results regarding the complex work of inpainting large missing areas in an image. This type of method generally attempts to generate one single "optimal" inpainting result, ignoring many other plausible results. However, considering the uncertainty of the inpainting task, one sole result can hardly be regarded as a desired regeneration of the missing area. In view of this weakness, which is related to the design of the previous algorithms, we propose a novel deep generative model equipped with a brand new style extractor which can extract the style noise (a latent vector) from the ground truth image. Once obtained, the extracted style noise and the ground truth image are both input into the generator. We also craft a consistency loss that guides the generated image to approximate the ground truth. Meanwhile, the same extractor captures the style noise from the generated image, which is forced to approach the input noise according to the consistency loss. After iterations, our generator is able to learn the styles corresponding to multiple sets of noise. The proposed model can generate a (sufficiently large) number of inpainting results consistent with the context semantics of the image. Moreover, we check the effectiveness of our model on three databases, i.e., CelebA, Agricultural Disease, and MauFlex. Compared to state-of-the-art inpainting methods, this model is able to offer desirable inpainting results with both a better quality and higher diversity. The code and model will be made available on https://github.com/vivitsai/SEGAN.

Little has been written in literature about the clinical comparison of the single use of chlorhexidine (CHX) rather than its combination with cetylpyridinium chloride (CPC). The purpose of this study was to compare the clinical effectiveness of two at-home antiseptic regimens. Healthy subjects scheduled for dental surgery were enrolled. After the surgery, patients were randomly allocated in a first group (Group A) which received a manual ultra soft toothbrush (Mentadent Professional®), an antiseptic toothpaste with 0,12% CHX and Vitamin B3 (Mentadent Professional Azione Intensiva Gengive®) and an antiseptic mouthwash with 0,12% CHX and 0,07% CPC. The second group (Group B) received solely an antiseptic mouthwash with 0,2% in conjunction with Anti Discoloration System (Curasept ADS/DNA®) and were encouraged to use their usual toothbrush and toothpaste. Patients were instructed to use the products twice a day and to rinse for 30 seconds. On day 7, patients were examined for the Early Healing Score, Visual Plaque Index of the sutures, Numerical Rating Scale and mouthwash taste. Group A showed a statistically significant levels of EHS and taste satisfaction. The regimen based on CHX associate with vitamin B3 in the toothpaste and CPC in the mouthwash resulted in superior clinical outcomes and satisfaction compared to solely CHX.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double &lt;100&gt; and &lt;111&gt; fiber and a unique component of (001)&lt;110&gt;, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

An effective on-board cloud detection method in small satellites would greatly improve the downlink data transmission efficiency and reduce the memory cost. In this paper, an ensemble method combining a lightweight U-Net with wavelet image compression is proposed and evaluated. The red, green, blue and infrared waveband images from Landsat-8 dataset are trained and tested to estimate the performance of proposed method. The LeGall-5/3 wavelet transform is applied on the dataset to accelerate the neural network and improve the feasibility of on-board implement. The experiment results illustrate that the overall accuracy of the proposed model achieves 97.45% by utilizing only four bands. Tests on low coefficients of compressed dataset have shown that the overall accuracy of the proposed method is still higher than 95%, while its inference speed is accelerated to 0.055 second per million pixels and maximum memory cost reduces to 2Mb. By taking advantage of mature image compression system in small satellites, the proposed method provides a good possibility of on-board cloud detection based on deep learning.

Heptanuclear {GdIII7} (complex 1) and tetradecanuclear {GdIII14} (complex 2) have been synthesized using a Rhodamine 6G ligand HL (Rhodamine 6G salicylaldehyde hydrazone) and characterized. Complex 1 has a rare disc-shaped structure, where the central Gd ion was connected to the peripheral six GdIII ions via CH3O-/μ3-OH- bridges. Complex 2 has an unexpected three-layer double sandwich structure with a rare μ6-O2- ion in the center of the cluster. Magnetic studies revealed that complex 1 exhibits a magnetic entropy change of 17.4 J kg−1 K−1 at 3 K and 5 T. On the other hand, complex 2 shows a higher magnetic entropy change of 22.3 J kg−1 K−1 at 2 K and 5 T.

Human disturbances can have severe environmental impacts on freshwater ecosystems. The main aim of this study was to detect the influences of physiochemical variables, land-cover characteristics, and river connectivity on fish assemblages in Lake Chaohu Basin, China. A cluster analysis of the river connectivity variables identified four groups of sites that characterized by significantly different connectivity gradients in local scale. These four groups of sites showed increasing connectivity from the upper reaches to the lower reaches. At the same time, among the four groups, the values of the environmental variables generally increased from the upper reaches with less human activity towards the lower reaches with more human activities. For instance, some main physiochemical variables (e.g., river width, water depth, nitrate, phosphate) significantly increased among the four groups. In contrast, fish taxa richness and diversity indices were not significantly different among the four connectivity groups. However, fish assemblages showed significant variation among the connectivity groups (p=0.026). In addition, the study determined that upper riparian land uses (e.g., woodland and grassland), flow velocity, and elevation were environmental variables regulating the variance in the fish communities, and for the connectivity variables, only river order and number of branches along a path to the left of the main stem affected the variance in the fish communities. Therefore, new practices aimed at maintaining and even increasing the riparian canopy coverage and the flow velocity of rivers should be integrated into local conservation planning for freshwater ecosystems, especially in the upper reaches of the basin.

Abstract: The two-dimensional Fuzzy Transform was applied in image compression. The quality of the image compressed with this methodis better than that obtained using methods based on fuzzy relation equations and comparable with that of the JPEG method, with better compression execution times. In this paper we propose a variation of the method based on the two-dimensional Fuzzy Transform of image compression, in which the image is first partitioned into blocks and then each block is compressed with the higher compression rate. The advantage of this method consistsinto a greater compression of the image, guaranteeing a high quality of the reconstructed image.The results show that our method is better than the Fuzzy Transform method improving also the quality of the reconstructed image.

The persistence of symptoms following COVID-19 infection represents a significant challenge in healthcare management. During the outbreak, tele-rehabilitation emerged as a new tool to support healthcare structures in providing rehabilitation services. This study assessed the effectiveness and the feasibility of a 3-week home-based motor and respiratory rehabilitation program for long COVID-19 individuals after traditional rehabilitation. Twenty-three patients completed the program and underwent functional tests at different time points (i.e. baseline, after hospital discharge, and after tele-rehabilitation). Motor function was evaluated using the instrumented Six-Minutes Walking Test (i6MWT), with monitored heart rate and oxygen saturation. Conversely, respiratory function was measured via forced vital capacity (FVC) and maximal voluntary ventilation (MVV) tests. Significant improvements (p &lt; 0.05) in motor and respiratory function were observed throughout the intervention, including an 18.3% increase in walked distance from the baseline. The findings suggest that a home-based tele-rehabilitation can enhance motor and respiratory function in post-COVID patients. Despite limitations such as sample size and lack of control group, the positive outcomes seem to support the feasibility of the proposed tele-rehabilitation program in managing long COVID symptoms and promoting functional recovery. Further research is needed to validate these findings and explore tele-rehabilitation’s potential in broader patient populations.

Vanilla planifolia is grown as a high-value orchid spice for its odor and savor attributes that increase due to the curing process associated with microbial colonization. This tends to influence the aromatic properties of vanilla. Hence, 11 Bacillus sp. strains were isolated from V. planifolia and identified with 16S rRNA gene sequencing. The liquid culture (1 mL of 107 CFU mL-1) of selected Bacillus vallismortis NR_104873.1:11-1518, B. velezensis ZN-S10, and B. tropicus KhEp-2 effectively fermented green-blanched vanilla pods kept at 10 ℃ during the sweating stage. GC-MS analysis showed that the methanol extract of non-coated, and B. vallismortis treated vanilla detected three (3) volatile compounds, whereas seven (7) components were obtained in B. tropicus and B. velezensis treatment. 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl was found in B. velezensis ZN-S10, B. tropicus KhEp-2, B. vallismortis while it was not present in the control samples. This ketone compound suggested a Maillard reaction resulting in brown-increased aroma pods. Linoleic acid and Hexadecanoic acid ethyl esters were detected only in ZN-S10 strain-coated vanilla. A novel 3--Deoxy-d-mannoic lactone was detected only in B. vallismortis treated vanilla characterized as a new compound in V. planifolia which suggested that the new compound can be altered with the coating of bacteria in vanilla during fermentation. Thus, the Bacillus strains improved the volatile profile and exhibited a new aroma and flavor profile of vanilla owing to bacteria fermentation during the curing process.

Background: COVID-19 infection has received the attention of the scientific community due its respiratory manifestations and association with evolution to severe acute respiratory syndrome (SARS-CoV-2). There are few studies characterizing SARS-CoV-2 in pediatric immunocompromised patients, such as liver transplanted (LT) patients.The aim of this study was to analyze the outcomes of the larger cohort of pediatric liver transplant recipients (PLTR) from a single center in Brazil who where contaminated with COVID-19 during the pandemic. Methods: Cross-sectional study. Primary outcomes: COVID-19 severity. The Cox regression method was used to determine independent predictors associated with the outcomes. Results: 74 PLTR were included. Patients were divided into two groups according to the severity of COVID-19 disease: moderate-severe COVID and asymptomatic-mild COVID. Patients categorized as moderate-severe COVID were younger (12.6 months vs. 82.1 months, p 0.03), higher prevalence of transplantation with deceased donor (50% vs. 4.3%, p 0.02) and with a higher prevalence of COVID-infected patients before 6 months after LT (75% vs. 5.7%, p 0.002). The independent predictor of COVID-19 severity identified in the multivariate analysis was COVID-19 infection < 6 months after LT (HR=0.001, 95% CI=0.001-0.67, p 0.03). Conclusion: The time interval of less than 6 months between COVID-19 infection and LT was the only predictor of disease severity in pediatric patients.

Contrasting results have suggested that the prevalence and intensity of post abortion emotional distress (PAD) either diminishes rapidly or persists over time. Few studies have followed women for longer than five years. This study examines retrospective population data on 226 ever aborting U.S. women aged 41-45, at an average of 20 years following the abortion, with extensive measures of PAD. Most post abortive women (55.2%) experienced little or no distress from their abortion(s) and 74.6% were confident it had been the right decision, but 44.8% reported moderate (20.7%) to high (24.1%) distress related to their abortion(s), including 37.7% who reported negative emotions; 31.2% “frequent feelings of loss, grief or sadness;” 24.6% “frequent thoughts, dreams, or flashbacks;” 23.2% for whom thoughts and feelings about their abortion “negatively interfered with life, work, or relationships.” Time since the abortion (mean 20 years, range 0-31 years) was not correlated with PAD (r = -.02, p .71). For the minority of women who experienced it, PAD did not diminish but persisted for decades. An estimated 7.5 million U.S. women currently experience persistent high PAD. Further research to specify risk factors and possible interventions for postabortion distress would be of value for this group of women.

Using the data of China's A-share non-financial listed enterprises from 2015 to 2022 as a sample, this study empirically tests the impact of ESG rating disagreement on corporate debt financing cost. The results show that ESG rating disagreement significantly increases the debt financing costs of enterprises, and this result still holds after a series of robustness tests such as replacing the dependent and independent variables and PSM approach. Meanwhile, the heterogeneity analysis reveals that non-state-owned enterprises and enterprises in non-heavily polluting industries are more sensitive to ESG ratings disagreement. In addition, mechanism analysis shows that corporate financing constraints mediate the relationship between ESG rating disagreements and debt financing costs. The findings of this study provide important evidence for understanding the impact of ESG rating disagreement on the costs of debt financing, enrich the meaning of ESG rating disagreement, and reveal the significance of unifying ESG rating standards.

Background: Perioperative complications after parotidectomy are poorly studied and have a potential impact on hospitalization stay. The Clavien-Dindo classification of postoperative complications used in visceral surgery allows a recording of all complications, including a grading scale related to the severity of complication. Methods: The cohort analyzed for perioperative complications is composed of 436 parotidectomies. classified into three types, four groups and three classes depending on extent of parotid resection, inclusion of additional procedures and pathology, respectively. Results: Using the Clavien-Dindo classification, complications were reported in 77 % of the interventions. In 438 complications, 430 (98.2%) were classified as minor (332 grade I and 98 grade II) and 8 (1.8%) were classified as major (grade III). Independent variables affecting the risk of perioperative complications were duration of surgery (odds ratio = 1.007, p-value = 0.029) and extent of parotidectomy (odds ratio = 4.043, p-value = 0.007). Total/subtotal parotidectomy was associated with an increased risk of grade II-III complications [odds ratio = 2.866 (95% CI: 1.307-6.283), p-value = 0.009]. Hospital stay increased in patients with complications (p= 0.0064). Conclusions: Use of Clavien-Dindo classification shows that parotidectomy is followed by a high rate of perioperative complications. Longer hospital stay is observed in patients with perioperative complications. Almost all complications are minor and have limited consequence on hospital stay.