This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

Hydrodynamic modeling and hazard mapping are essential tools for urban flood mitigation and spatial planning. Leveraging software like HEC-RAS (Hydrologic Engineering Center - River Analysis System) and ArcGIS, this study aimed to map flood-prone areas along the Jijia River in the Ungheni administrative unit of Iasi County. Human-induced environmental changes and global climate shifts have heightened flood risks worldwide, particularly in urbanized areas. Hydrological and hydraulic modeling anticipate and assess flood events, while hydrodynamic modeling accurately simulates flow propagation, in-forming flood extent, timing, and volume. Flood hazard maps offer essential insights into flooded areas, water depths, and velocities, assisting in risk assessment and mitigation strategies. Through the use of different scenarios, river modeling aims to accurately replicate real-world conditions. This study focuses on Ungheni commune in Iasi County, Romania, situated along the Prut River's eastern bank. Utilizing a combination of fixed-grid and irregular mesh elements in modeling al-lows for fine-tuning of flow details and optimization of simulation times. Model accuracy, particularly regarding peak river levels, hinges on hydrograph duration. While a 30-minute error is typically accepted, greater tolerances may apply to river basins with longer response times. The extraction and processing of model results, including maximum water depths, flood extents, and velocity maps, are facilitated by ArcGIS, providing valuable data for effective flood management strategies.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Optical wireless video transmission technology combines the advantages of high data rates, enhanced security, large bandwidth capacity, and strong anti-interference capabilities inherent in optical communication, establishing it as a pivotal technology in contemporary data transmission networks. However, video data comprises a large volume of image information, resulting in substantial data flow with significant redundant bits. To address this, we propose an adaptive block sampling compressive sensing algorithm that overcomes the limitations of sampling inflexibility in traditional compressive sensing, which often leads to either redundant or insufficient local sampling. This method significantly reduces the presence of redundant bits in video images. First, the sampling mechanism of the block-based compressive sensing algorithm was optimized. Subsequently, a wireless optical video transmission experimental system was developed using a Field-Programmable Gate Array chip. Finally, experiments were conducted to evaluate the transmission of video optical signals. The results demonstrate that the proposed algorithm improves the Peak Signal-to-Noise Ratio by over 3 dB compared to other algorithms, with an enhancement exceeding 1.5 dB even in field tests, thereby significantly optimizing video transmission quality. This research contributes essential technical insights for the enhancement of wireless optical video transmission performance.

The relentless advancement and integration of mechanization and intelligence within the coal mining industry, combined with the increasing depths of mining operations, necessitate significantly higher safety standards. This necessity arises due to the increasingly complex geological and coal seam conditions encountered as mining operations delve deeper into the earth. Traditionally, 3D seismic exploration technology has been fundamental in ensuring both operational efficiency and safety in the coal mining sector. However, despite its critical role, this technology still has limitations in detecting and characterizing small-scale geological structures which can pose substantial risks if not accurately identified and mitigated. To address these challenges, this paper introduces a sparsity-constrained adaptive hard thresholding algorithm designed to tackle the spectral inversion optimization problem with an norm constraint for the enhanced retrieval of reflection coefficients, thereby establishing a comprehensive workflow for enhancing seismic data resolution through compressed sensing spectral inversion. Real data validation has demonstrated that this method significantly enhances the resolution of seismic data while maintaining the amplitude integrity and fidelity of the original signals. This improvement allows for a more detailed and accurate characterization of small-scale geological features, which are critical in identifying and mitigating potential hazards within coal mining operations, thus offering robust support for the implementation of more effective safety protocols and disaster prevention strategies in coal mines.

The article focusses on detecting the unbalance of a mechanical component in the electric drive system of a two-mass servomechanism with a PMSM motor, which is connected to the load via a long, flexible shaft. In the example analysed, the degree of unbalance was determined using the reference current signal from the speed controller of the FOC control system. The authors pre-sented a two-mass model with an unbalanced mechanical system. The STFT transform was used to analyse the symptoms of unbalance and an artificial neural network MLP was used for system state inference. The effectiveness of the presented analysis, based on the reference current signal from the sensor embedded in the control system, was experimentally confirmed.

We construct a Bayesian estimator for the dilution of a wastewater sample. When wastewater is diluted by rainwater an estimate of the level of dilution is required if we are to normalise sample measurements of disease markers such as SARS-CoV-2 RNA. We consider the situation where flow measurements are available, but will regularly be unreliable because of the action of combined sewer outflows (CSOs) and wastewater storage tanks, which divert wastewater away from treatment plants when the flow is excessive. However, we also have proxies for the flow from various chemical markers (e.g.\ phosphate, ammonium, electrical conductivity), whose level per unit of population is fixed. The new flow estimator has multiple advantages compared to existing procedures: credible intervals for the estimates; optimal weighting of the chemical markers; systematic handling of missing and censored values; and model based smoothing without lags.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

Modification of electrode surface with a selective layer gives the possibility to detect target ana-lytes of forensic interest. 3-(4-trifluoromethyl)-phenyl)-thiophene (ThPhCF3) was deposited on a graphite (G) electrode by electrochemical oxidation and characterized as a receptor for the recognition of synthetic stimulants (2-aminoindane, buphedrone, naphyrone). First, the structural characterization of the polymeric layer were obtained from Raman spectroscopy. Second, the electrochemical profiles of selected synthetic stimulants and their affinity to ThPhCF3/G-modified electrodes were studied using square wave voltammetry and electrochemical impedance spec-troscopy. The values of the adsorption constant show the importance of – PhCF3 groups in the interaction with synthetic stimulants, namely recognition by the formation of hydrogen bonds (Kads (buphedrone) < Kads (2-AI)) and interaction with aromatic H atoms (Kads (buphedrone) < Kads (naphyrone)). It was demonstrated that the polymeric layer derived from thiophene with – PhCF3 group is capable to increase the intensity of the electrochemical signal.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

This study explores the prediction of concrete compressive strength using machine learning models, aiming to overcome the time-consuming and complex nature of conventional methods. Four models—Artificial Neural Network, Multiple Linear Regression, Support Vector Machine, and Regression Tree—are employed and compared for performance. Evaluation metrics such as Mean Absolute Deviation, Root Mean Square Error, Coefficient of Correlation, and Mean Absolute Percentage Error are used. After preprocessing 1030 samples, the dataset is split into 70% for training and 30% for testing. The ANN model, further divided into training, validation (15%), and testing (15%), outperforms others in accuracy and efficiency. This outcome streamlines compressive strength determination in the construction industry, saving time and simplifying the process.

Compressive sensing (CS) is a technique that allows a signal vector to be reconstructed with a number of linear measurements far fewer than its size. In this study, optical hybrid cryptography with simultaneous compressive sensing based on orthogonal matching pursuit (OMP) is proposed as an alternative solution to the two important problems in communications, namely, effective / efficient / signal processing and secure encryption/decrypton. The whole system is able to both compress and encrypt data with attack immunity.

Compressive sensing originates in the field of signal processing and has recently become a topic of energy-efficient data gathering in wireless sensor networks. In this paper, we propose an energy efficient distributed compressive sensing solution for sensor networks. Proposed solution utilizes sparsity distribution of signals to group sensor nodes into several coalitions and then implements localized compressive sensing inside coalitions. This solution improves data-gathering performance in terms of both data accuracy and energy consumption. The approach curbs both data-transmission costs and number of measurements. Coalition-based data gathering cuts transmission cost, and the number of measurements is reduced by scheduling sensor nodes and adjusting their sampling frequency. Our simulation showed that our approach enhances network performance by minimizing energy cost and improving data accuracy.

External hoof characteristics, balance, and conformation have been extensively studied in horses; however, mules remain understudied in these aspects. This study evaluated the size, shape, and symmetry of untrimmed and unshod forelimb hooves, compared the symmetry between forelimb hooves and stratified external forelimb hoof measurements based on the body condition score of mules raised in the foothill plains of northern Thailand. The forelimb hooves of 38 mules were photographed and 33 parameters, including angular and linear measurements, were analyzed. Despite the absence of shoeing and trimming, these mules exhibited optimal left-right forelimb hoof symmetry, with no significant (p < 0.05) differences in: outer wall length and inner wall length (OWL - IWL); sole length and sole width (SLS - SW); dorsal hoof wall length and heel length (DHWL - HL); and frog length and frog width (FL - FW). However, significant (p < 0.05) differences were observed within each body condition score group for forelimb hoof measurements for DHWL, IWL, heel separation (HS), heel bulb distance (HBD), SW, FW, and FL. These findings provide valuable insights into mule welfare and management, contributing to understanding of the interplay between overall health and hoof conformation in the study area.

Emerging data processing techniques brought back into attention the HF range communication as an interesting alternative to third-party solutions for IoT applications, such as data transmission in distributed energy production facilities. The physical size of HF antennas, often comparable to the surrounding objects, require in-situ radiation measurements. Drone-borne measuring systems are already known as a flexible solution, but mostly restricted to higher frequency ranges. In this work, we propose to use an electrically small, folded dipole as a probe for drone-borne measurements on HF antennas. We also propose a calibration approach for the effects related to the near-field zone, and to the drone body proximity. The impact of ground reflection is also investigated. We show that despite its low, realized gain figure such a probe can provide stable results for near-field measurements, even at low input power levels.

Steel surface protection with hard coatings is essential in the metalworking industry, yet developing high-performance hard coatings still remains a challenge. Quaternary nitride coatings, particularly TiAlSiN, have been extensively studied, but commercial TiAlSiN coatings vary widely, and there is a lack of consistent data. This study presents findings on the development and evaluation of TiAlSiN and TiAlSiN/TiN thin films, with an 800 nm thick TiAlSiN top coating and a 100 nm thick TiN mid-coating. The films were deposited on C120 tool steel discs via reactive DC magnetron sputtering. Ti and TiAlSi 75–20–5 (at.%) disc-shaped targets (50.8 mm diameter × 6.3 mm thickness), fabricated by our team through spark plasma sintering, were used for the sputtering process. Coatings were grown on smooth steel substrates heated to 300 °C, resulting in a uniform micro-structure with nanoparticles of globular (TiN) or pyramidal shape (TiAlSiN), as evidenced by SEM analysis. Nanoindentation tests showed superior mechanical properties for all coatings compared to the steel substrate. Micro-scratch tests indicated better scratch resistance for TiAlSiN/TiN bilayer (BL) coatings than for TiAlSiN single-layer (SL) coatings. Electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution revealed that the BL coatings demonstrated superior corrosion resistance compared to the SL coatings, even after thermal aging at 800 °C for 1 hour. The superior properties of the synthesized TiAlSiN/TiN films recommend them as protective coatings for tool steel surfaces.

Background: This study focuses on different manual handling methods and their effect on psychomotor skills concerning physical measurements (height, weight, age) and pinch strength. Objective: To assess the effects of three manual handling techniques on psychomotor skills and to establish the prediction of pinch strength by physical measurements. Methods: Three manual handling methods were tested: handling with a 90-degree elbow angle, handling with one hand, and handling with both hands. Psychomotor skills were quantified through handgrip strength, dexterity tests, and perceived exertion scales. Linear and random forest regression models were used to predict pinch strength from physical measurements. Results: Handling with a 90-degree elbow angle significantly increased perceived exertion and error rates while decreasing post-task handgrip strength. The one-hand method showed the least negative effect on psychomotor abilities. Weight emerged as the most influential predictor of pinch strength, followed by height and age. The random forest regression model outperformed the linear regression model, indicating its suitability for capturing complex non-linear relationships among variables. The Random Forest Regression model excelled in predicting weight with a high R² score of 0.78, showing strong predictive power. It was moderately effective for height with an R² score of 0.42. However, it performed poorly for age prediction, with an R² score of 0.01, indicating ineffective features for predicting age. Conclusion: The results emphasize the importance of ergonomic interventions and training programs to optimize manual handling practices, aiming to reduce physical strain and enhance worker productivity and safety. Maintaining muscle strength is crucial in older age groups due to the decline in pinch strength with age. These findings can inform intervention studies and the modification of occupational health and safety practices. Future research should aim to validate these results across diverse populations and explore additional factors influencing handgrip strength.

We propose a novel data hiding method in an audio host with a compressive sampling technique. An over-complete dictionary represents a group of the watermark. Each row of the dictionary is a Hadamard sequence representing multiple bits of the watermark. Then, the singular values of segment-based host audio in a diagonal matrix multiply by the over-complete dictionary producing a lower size matrix. At the same time, we embed the watermark into the compressed audio. In the detector, we detect the watermark and reconstruct the audio. This proposed method offers not only hiding the information but also compressing the audio host. The application of the proposed method is a broadcast monitoring and biomedical signal recording. We can mark and secure the signal content by hiding the watermark inside the signal while we compress the signal for memory efficiency. We evaluate the performance in terms of payload, compression ratio, audio quality, and watermark quality. The proposed method can hide the data imperceptibly, in range 729-5292 bps with compression ratio 1.47-4.84 and perfect detected watermark.

This paper proposes the use of compressive sensing to tackle the Massive MIMO channel estimation problem. As our results show compressive sensing-based estimators perform as well as the optimum MMSE estimator.

With the development of hyperspectral technology, to establish an effective spectral data compressive reconstruction method that can improving data storage, transmission and maintaining spectral information is critical for quantitative remote sensing research and application in vegetation. By introducing the idea of compressive sensing in compressed reconstruction, the spectral adaptive grouping distributed compressive sensing algorithm is proposed, which enables a distributed compressed sensing reconstruction of plant hyperspectral data. The experimental results showed that comparing with orthogonal matching pursuit(OMP) and gradient projection reconstruction(GPSR), the proposed algorithm can significantly improve the visual effect of image reconstruction in the spatial domain. The PSNR in low sampling rate(sampling rate is lower than 0.2) increases by 13.72dB than OMP and 1.66dB than GPSR. In the spectral domain, the average normalized root mean square error、the mean absolute percentage error and the mean absolute error of the proposed algorithm is35.38%，31.83% and 33.33% lower than GPSR respectively.. Therefore, the proposed algorithm can achieve relatively high reconstructed efficiency.

In the context of video background-foreground separation, we propose a compressive online Robust Principal Component Analysis (RPCA) with optical flow that separates recursively a sequence of video frames into foreground (sparse) and background (low-rank) components. This separation method can process per video frame from a small set of measurements, in contrast to conventional batch-based RPCA, which processes the full data. The proposed method also leverages multiple prior information by incorporating previously separated background and foreground frames in an n-l₁ minimization problem. Moreover, optical flow is utilized to estimate motions between the previous foreground frames and then compensate the motions to achieve higher quality prior foregrounds for improving the separation. Our method is tested on several video sequences in different scenarios for online background-foreground separation given compressive measurements. The visual and quantitative results show that the proposed method outperforms other existing methods.

Temporomandibular disorders (TMDs) refer to a group of conditions that affect the temporomandibular joint, causing pain and dysfunction in the jaw joint and related muscles. The diagnosis of TMDs typically involved clinical assessment through operator-based physical examination, self-reported questionnaire and imaging studies. To objectivize the measurement of TMD, this study aims at investigating on the feasibility to use machine-learning algorithms fed with data gathered from low-cost and portable instruments to discriminate the presence of TMD in adult subjects. Through this aim, the experimental protocol involved fifty participants, equally distributed between TMD and healthy subjects, acting as control group. The diagnosis of TMD has been performed by a skilled operator through the typical clinical scale. Participants underwent to a baropodometric analysis by using a pressure matrix and the evaluation of the cervical mobility through inertial sensors. Nine machine-learning algorithms belonging to support vector machine, k-nearest neighbours and decision tree were compared. The k-nearest neighbours based on cosine distance was found as the best performing, achieving performance of 0.94, 0.94 and 0.08 for the accuracy, F1-score and G-index, respectively. These findings open the possibility to use such methodology to support the diagnosis of TMDs in clinical environments.

A standard method assessing postural control is the measurement in standing position. However, the implementation is usually only possible to a limited extent. Recording of postural control directly on the trunk, in seated position, could provide an alternative diagnostic method for quantifying neuromuscular control. Comparison of the measurements of Center of Pressure (CoP) in standing and seated position was performed on 66 healthy adult subjects. Reliability of measurements in seated position was tested on 23 subjects. In addition, the extension force of all test subjects was recorded. The assessments of CoP fluctuations in standing and seated position showed adequate agreement (deviation 9.1%). Furthermore, good internal consistencies with a sufficient test re test reliability could be demonstrated for the measurements in seated position. Both CoP measurement methods showed a comparable Spearman correlation to obtained extension force measurements (standing: 0.24, seated: 0.23). Our results show that recording CoP flucutations in the seated position is a reliable and valid additional method to measurements in the single legged stance. It could serve as an additional alternative to quantify neuromuscular control in impaired patients in whom single-leg stance cannot be performed adequately. In addition, the measurement in sitting position enables the direct recording of neuromuscular control on the trunk.

Microvascular self-healing composite materials have significant potential for application and their mechanical properties need in-depth investigation. In this paper, tensile and compressive properties of woven fabric carbon fiber reinforced polymers (CFRP) laminates containing three-dimensional microvascular channels were investigated experimentally. Several detailed finite element (FE) models were established to simulate the mechanical behavior of the laminate and the effectiveness of different models were examined. The damage propagation process of the microvascular laminates and the influence of microvascular parameters were studied by the validated models. The results show that microvascular channels arranged along the thickness direction (z-direction) of the laminates are critical locations under the loads. The channels have minimal effect on the stiffness of the laminates but causing a certain reduction in strength, which varies approximately linearly with the z-direction channel diameter within its common design range of 0.1~1mm. It is necessary to consider the resin-rich region formed around microvascular channels in the warp and weft fiber yarns of the woven fabric composite when establishing the FE model. And the layers in model should be assigned with equivalent unidirectional ply material in order to calculate the mechanical properties of laminates correctly.

A variant of the von Neumann-Wigner Interpretation is proposed. Problems arising from the quantum Zeno effect are addressed as we have described previously. We do, however, offer some new, and perhaps unexpected observations. We are accustomed to thinking of wave function collapse as occurring consequent to laboratory measurements. We speculate that, whatever physical correlate of consciousness exists within the brain, it is quantum mechanical in the sense that a brain, left to itself, would eventually decohere into a state no longer compatible with its conscious functioning. Wave function collapse returns it to a state compatible with consciousness. Indeed, this may be its important reason for occurring. A universe without it simply could not play host to conscious brains. The fact that it also prevents us from encountering "absurd" situations in the laboratory is merely a fortunate dividend. Whenever a quantum measurement is made the universe's future history splits into a number of possibilities. This number may be very large or infinite. And we believe consciousness plays a vital role in this happening. A "conscious" universe where quantum measurements are being made allows for an enormous number of equally acceptable world-histories. An "unconscious" one, always evolving in a unitary fashion, allows for only one. If we assume that the decision as to which worldhistory is the real one (i.e. this one) is made at random we see that the universe is overwhelmingly more likely to be "conscious" than not.

Flue gas desulfurization gypsum (FGD gypsum) is obtained from the desulphurization of combustion gases in fossil fuel power plants. FGD gypsum can be used to produce anhydrite binder. The effect of three independent variables such as the calcination temperature of FGD gypsum (500-800 oC), the hydration time (3-28 days) and the amount of activator (0-2 %) on the compressive strength of anhydrite binder were studied. K2SO4 and Na2SO4 were used as activators. The compressive strength of anhydrite binder was evaluated using a full factorial design. The multiple linear regression models were developed to correlate the significant variables to the compressive strength of anhydrite binder. The experimental results and statistical analysis showed that the hydration time had the biggest impact on the compressive strength of anhydrite binder using K2SO4 and Na2SO4. K2SO4 made a greater influence on the compressive strength than Na2SO4. The results of modeling indicated that the individual variables had a larger effect on the compressive strength of anhydrite binder than their interaction. The mean absolute percentage error between experimental and calculated values of compressive strength was less than 10 %.

In remote sensing applications, one of the key points is the acquisition, real-time pre-processing and storage of information. Due to the large amount of information present in the form of images or videos, compression of this data is necessary. Compressed sensing (CS) is an efficient technique to meet this challenge. It consists in acquiring a signal, assuming that it can have a sparse representation, using a minimal number of non-adaptive linear measurements. After this CS process, a reconstruction of the original signal must be performed at the receiver. Reconstruction techniques are often unable to preserve the texture of the image and tend to smooth out its details. To overcome this problem, we propose in this work, a CS reconstruction method that combines the total variation regularization and the non-local self-similarity constraint. The optimization of this method is performed by the augmented Lagrangian which avoids the difficult problem of non-linearity and non-differentiability of the regularization terms. The proposed algorithm, called denoising compressed sensing by regularizations terms (DCSR), will not only perform image reconstruction but also denoising. To evaluate the performance of the proposed algorithm, we compare its performance with state-of-the-art methods, such as Nesterov's algorithm, group-based sparse representation and wavelet-based methods, in terms of denoising, and preservation of edges, texture and image details, as well as from the point of view of computational complexity. Our approach allows to gain up to 25% in terms of denoising efficiency, and visual quality using two metrics: PSNR and SSIM.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

Background: This study assesses the effects of the ‘Radiant’ image enhancement technique on fetal nuchal translucency (NT) measurements during first trimester sonographic ex-ams. Methods: A retrospective analysis of 263 ultrasound images of first trimester midsagittal sections was conducted. NT measurements were obtained using a semi-automatic tool. Statistical methods were applied to compare NT measurements with and without ‘Radi-ant’ enhancement. An in-vitro setup with predefined line distances provided additional data. Results: Incremental increases in NT measurements were observed with varying levels of ‘Radiant’ application: An average increase of 0.19 mm with ‘Radiant min’, 0.24 mm with ‘Radiant mid’ and 0.30 mm with ‘Radiant max.’ The in-vitro results supported these findings, showing consistent effects on line thickness and measurement accuracy, with the smallest mean deviation occurring at the ‘Radiant mid’ setting. Conclusions: ‘Radiant’ image enhancement leads to significant increases in NT measure-ments. To avoid systematic biases in clinical assessments, it is advisable to disable ‘Radi-ant’ during NT measurement procedures. Further studies are necessary to corroborate these findings and to consider updates to the NT reference tables based on this technology.

Based on an in-depth analysis of the factors influencing the compressive strength of ultra-high performance concrete (UHPC), this study examined the impact of both single factors and combined factors on UHPC performance using experimental data. The correlation analysis indicates that cement content, water content, steel fiber, and fly ash significantly affect the strength of UHPC, whereas silica fume, superplasticizers, and slag powder have a relatively smaller influence. This analysis provides a scientific basis for model development. Furthermore, the support vector regression (SVR) model was optimized using the arithmetic optimization algorithm (AOA). The superior performance and computational efficiency of the AOA-SVR model in predicting UHPC compressive strength were validated. Compared to SVR, support vector machine（SVM）, and other single models, the AOA-SVR model achieves the highest R2 value and the lowest error rates. The results demonstrate that the optimized AOA-SVR model possesses excellent generalization ability and can more accurately predict the compressive strength of UHPC.

In vivo, articular cartilage tissue is surrounded by a cartilage membrane, and HP (HP) and compressive strain increases simultaneously with the compressive stress. However, it has been impossible to investigate the effects of simultaneous loading in vitro. In this study, a bioreactor capable of applying compressive stress under HP was developed to reproduce ex vivo the same physical loading environment found in cartilage in vivo. First, a HP stimulation unit was constructed to apply cyclic HP pressure-resistant chamber by controlling a pump and valve. A compression-loading mechanism that can apply compressive stress using an electromagnetic force was implemented in the chamber. The synchronization between the compression and HP units were evaluated and the stimulation parameters were quantitatively evaluated. Physiological HP and compressive strain were applied to the chondrocytes encapsulated in alginate and gelatin gels after applying high HP at 25 MPa, which induced damage to chondrocytes. It was found that compressive stimulation increased the expression of genes related to osteoarthritis. Furthermore, the simultaneous application of compressive strain and HP, which is similar to the physiological environment in cartilage, had an inhibitory effect on the expression of genes related to osteoarthritis. HP alone also suppressed the expression of osteoarthritis-related genes. Therefore, the simultaneous hydrostatic and compressive stress-loading device developed to simulate the mechanical environment in vivo may be an important tool for elucidating the mechanisms of disease onset and homeostasis in the cartilage.

(1) Background: The study aimed to investigate compressive strength for three computer-aided design/computer-aided manufacturing (CAD/CAM) dental materials: glassceramic IPS Empress CAD (IvoclarVivadent), hybrid ceramic Cerasmart (GC) and polymer-reinforced graphene G-CAM (Graphenano Dental). (2) Methods: 45 samples consisted of the molar crowns fabricated by three CAD/CAM materials were cemented adhesively on 3D printed abutments (Asiga DentalResin). The samples were divided into 3 groups (n=15) according to the crowns thickness; group 1 under the cusps/cervical margins - 0.6 mm/0.4 mm, group 2 - 1 mm/0.7 mm respectively, and group 3 - 1.5 mm/1 mm. Additionally, 20 cylindrical specimens fabricated by the three crowns and abutments material (n=5) were prepared by CAD/CAM technique. All samples and specimens were subjected to an axial compressive load by using a universal testing machine (Instron 3366-10kN, USA) until fracture. (3) Results: The compressive strength were for Empress CAD 1258 MPa, Cerasmart 501.3 MPa, G-CAM 435 MPa and Asiga resin 360 MPa. G-CAM crowns exhibited a higher maximum compressive load (1701.5-2011.8N) than both Cerasmart (1295.4-1642.9N) and Empress CAD (494.3-597.5N). (4) Conclusions: The CAD/CAM crown materials presented different mechanical behavior; Empress CAD and Cerasmart presented a fragile behavior, with a high compressive strength when compared to G-CAM and Asiga resins.

Influence of particle size on the mechanical strength of alkali activated material from waste refractory monolithic was investigated in this study. Precursor was chemically and mineralogically analysed, separated on 4 fractions and alkali activated with Na-water glass. Alkali activated materials were thoroughly investigated under SEM and XRD to evaluate the not predicted differences in mechanical strength. Time dependence of curing temperature on mechanical strength was investigated in the sample prepared from a fraction that caused the highest compressive strength.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

The comparison of three types of ionosonde data from Europe during an Interplanetary Coronal Mass Ejection (ICME) and a Stream Interaction Regions (SIRs) / Corotating Interaction Regions (CIRs) -driven geomagnetic storm event is detailed in this study. The selected events are 16-20 March 2015 for the ICME-driven and 30 May to 04 June 2013 for the SIR/CIR-driven one. Ionospheric data from three European ionosonde stations, namely Pruhonice (PQ), Sopron (SO) and Rome (RO), are investigated. The ionospheric F2-layer responses to these geomagnetic events are analyzed with the ionospheric foF2 and h’F2 parameter, the calculated deltafoF2 and deltahF2 values, ratio of Total Electron Content (rTEC) and Thermosphere, Ionosphere, Mesosphere, Energetics and Dynamics (TIMED) satellite Global Ultraviolet Imager (GUVI) thermospheric [O]/[N2] measurement data. The storm-time and the quiet day mean values are also compared, and it can be concluded that the quiet day curves are similar at all stations while the storm-time ones showed the latitudinal dependence during the development of the storm. As a result of the electron density comparison, during the two events it can be concluded that SSC that characterized the ICME induced a Travelling Atmospheric Disturbance (TAD) seen in the European stations, while this is not in the SIR/CIR-driven ionospheric storm, which showed a stronger and more prolonged negative effect in all stations probably due to the season.

The moiré effect is typically observed in regular periodic structures and sometimes in random (aperiodic) structures. However, only regular structures were used in measurements. In this study, we propose structures whose images are not regular but not completely random, and resemble a series of lines, such as a grid of dotted lines or a matrix of dots. A relatively simple image processing technique can make the moiré effect in such structures very similar to regular structures. We demonstrated using five different structures (including text) in measurements, with similar results.

Digital filtering is a fundamental technique in digital signal processing, which operates on a digital sequence without any information on how the sequence was generated. This paper proposes a methodology for designing the equivalent of digital filtering for neuromorphic samples, which are a low power alternative to conventional digital samples. In the literature, filtering using neuromorphic samples is done by filtering the reconstructed analog signal, which is required to belong to a predefined input space. We show that this requirement is not necessary, and introduce a new method for computing the neuromorphic samples of the filter output directly from the input samples, backed by theoretical guarantees. We show numerically we can achieve a similar accuracy compared to the conventional method. However, given that we bypass the analog signal reconstruction step, our results show significantly reduced computation time for the proposed method and good performance even when signal recovery is not possible.

The purpose of this work is to determine the possibility of using an automated SkyWatcher Virtuoso system to analyze distribution of sky luminance. The article presents the procedure for measuring the sky luminance distribution defined according to CIE using a manual luminance meter cooperating with the SkyWatcher system. The use of matrix luminance meter was also analyzed.

Unmanned Aerial Vehicles (UAVs) are now filling in the gaps between spaceborne and ground-based observations and enhancing the spatial resolution and temporal coverage of data acquisition. In the realm of hydrological observations, UAVs have a key role to quantitatively characterize the surface flow allowing for remotely accessing the water body of interest. In this paper we propose a technology which uses a sensing platform encompassing a drone and a camera to determine the water level. The images acquired my means of the sensing platform are then analyzed using the Canny method to detect the edges of water level and of Ground Control Points (GCPs) used as reference points. The water level is then retrieved from images and compared to a benchmark value obtained by a traditional device. The method is tested at four locations in an artificial lake in central Italy. Results are encouraging as the overall mean error between estimated and true water level values is around 0.02 m. This technology is well suited to improve hydraulic modeling and thus provide a reliable support to flood mitigation strategies also in uneasy-to-access environments.

This study is focused on the experimental investigation of compressive strength and durability properties of lightweight concrete mixtures with fine expanded glass and expanded clay aggregates using different microfillers. The paper proposes the relationships between the compressive strength and density of concrete mixtures with different proportions of lightweight aggregates mentioned above. The performed experimental studies have revealed the tendencies of possible usage of different amount of fine lightweight aggregates and their combinations in the production of concrete mixtures depending on the demands of practical application. Following the requirements for structural concrete subjected to environmental effects, durability properties (alkaline corrosion and freeze–thaw resistance) of the selected concrete mixtures with expanded glass aggregate were studied. The results of the experimental investigations have shown that durability of tested concrete specimens was sufficient. The study has concluded that the mixtures under consideration can be applied for the production of structural elements to which durability requirements are significant.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

This research aims to study the ultimate limit state (ULS) behaviour of stiffened panel under longitudinal compression by non-linear finite element method (NLFEM). There are different types of stiffeners being used in shipbuilding i.e. T-bar, flat-bar and angle-bar. However, this research focuses on the ultimate compressive strength behaviour of flat-bar stiffened panel. A total of 420 of reliable scenarios of flat-bar stiffened panel are selected for numerical simulation by ANSYS NLFEM. The ultimate strength behaviours obtained were used as data for the development of closed form shape empirical formulation. Recently, Kim et al. [1] proposed for advanced empirical formulation for T-bar stiffened panel and the applicability of the proposed formulation to flat-bar stiffened panel will be confirmed by this study. The accuracy of the empirical formulation obtained for flat-bar stiffened panel has been validated by FE simulation results of statistical analysis (R2 = 0.9435). The outcome obtained will be useful for ship structural designers in predicting the ultimate strength performance of flat-bar type stiffened panel under longitudinal compression.

Osteoarthritis (OA) is a common joint disorder found mostly in elderly people. The role of mechanical behavior in the progression of OA is complex and remains unclear. The stress-relaxation behavior of human articular cartilage in clinically defined osteoarthritic stages may have importance in diagnosis and prognosis of OA. In this study we investigated differences in the biomechanical responses among human cartilage of ICRS grades I, II and III using polymer dynamics theory. We collected 24 explants of human articular cartilage (eight each of ICRS grade I, II and III) and acquired stress-relaxation data applying a continuous load on the articular surface of each cartilage explant for 1180 s. We observed a significant decrease in Young’s modulus, stress-relaxation time, and stretching exponent in advanced stages of OA (ICRS grade III). The stretch exponential model indicated that significant loss in hyaluronic acid polymer might be the reason for the loss of proteoglycan in advanced OA. This work encourages further biomechanical modelling of osteoarthritic cartilage utilizing these data as input parameters to enhance the fidelity of computational models aimed at revealing how mechanical behaviors play a role in pathogenesis of OA.

Aim: To investigate the effects of intensive physical exercise on retinal microvascular regulation in healthy volunteers by the adaptive optics retinal camera measurement. Methods: We included healthy volunteers (11 men and 14 women) aged 20.6± 0.9. Heart rate (HR) and systolic and diastolic blood pressure (SBP, DBP) were recorded before and after a submaximal physical exertion of continuously riding a training ergometer. The superior temporal retinal artery measurements were captured using the adaptive optics (AO) camera rtx1TM (Imagine Eyes, Orsay, France) without pupil dilatation. We compared measures of vessel diameter (VD), lumen diameter (LD), two walls (Wall 1, 2), wall-to-lumen ratio (WLR), and wall cross-sectional analysis (WCSA) before and immediately after the cessation of exercise. Results: Cardiovascular parameters: After exercise, SBP, DBP and HR changed significantly from 130.2±13.2 to 159.7±15.6 mm Hg, 81.2±6.3 to 77.1±8.2 mm Hg and 80.8±16.1 to 175.0±6.2 bpm, respectively (p < 0.002). Retinal microcirculation analysis: Before the exercise, the mean LD was 96.0±6.8, VD 118.5±8.3, WLR 0.234±0.02, WCSA 3802.8±577.6. The mean LD and Wall 1 did not change significantly after exercise but slightly decreased. The VD, Wall 2, WLR and WCSA decreased significantly (p

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

Capacitive contact imaging has shown potential in measuring skin properties including hydration, micro relief analysis, as well as solvent penetration measurements. Through calibration we can also measure the absolute permittivity of the skin, and from absolute permittivity we then work out the absolute solvent content in skin. In this paper, we present our latest study of capacitive contact imaging for skin characterizations and vivo skin solvent penetration. We will show how to use capacitive occlusion measurements to characterize skin damages, and how to calculate the absolute water content and solvent content in skin.

Organisations need dynamic capabilities in the ongoing digital transformation to reconfigure knowledge and learning. There is a need to define new concepts and explain mechanisms of relevant factors to build dynamic capabilities. Especially organisations acting in healthcare are caught in a dilemmatic situation. New, digital processes and business models are promising benefits for cost-containment measures and improved patient-centric care, offering digital services. However, investments are needed to benefit. The important question is: how can individual actors in healthcare be motivated to engage in this transformational process to build and reconfigure relevant competences and establish new learning routines? Founded on the essence of existing literature, we assume sustained learning as a relevant dynamic capability to seize and sense competences and reconfigure human capital. This paper answers the call for deeper investigations into the mechanisms in new digitally transformed environments and sectors with less focus on performance and competitive advantages, like public administration or the healthcare sector. Based on previous research, validated in qualitative interviews and quantitative testing, we define the new construct of sustained learning with its subdimensions. By providing measures, we build the ground for further quantitative research.

The result of the multidisciplinary collaboration of researchers from different areas of knowledge to validate a solar radiation model is presented. The MAPsol is a 3D local-scale adaptive solar radiation model that allows to estimate direct, diffuse and reflected irradiance for clear sky conditions. The model includes the adaptation of the mesh to complex orography and albedo, and considers the shadows cast by the terrain and buildings. The surface mesh generation is based on surface refinement, smoothing and parameterisation techniques and allows the generation of high quality adapted meshes with a reasonable number of elements. Another key aspect of the paper is the generation of a high-resolution digital elevation model (DEM). This high-resolution DEM is constructed from LiDAR data and its resolution if two times more accurate than the publicly available DEMs. The validation process uses direct and global solar irradiance data obtained from pyranometers at the University of Salamanca located in an urban area affected by systematic shading from nearby buildings. This work provides an efficient protocol for studying solar resources, with particular emphasis on areas of complex orography and dense buildings where shadows can potentially make solar energy production facilities less efficient.

The paper presents the methods of assessing the technical condition of varistor surge arresters used in laboratory tests and in operation - performed without disconnecting the arresters from the network. The analysis of diagnostic methods was supplemented with the results of measurements of the leakage current of arresters coming directly from production and used in the power industry. Among the available methods of evaluating the technical condition of arresters, mainly indicator solutions (temperature, operation counter) and using the measurement of selected parameters of the leakage current are used. In the latter, the method of determining the resistive component of the leakage current, determined on the basis of the analysis of voltage and current waveforms, or only the arrester current, has become widespread. In this type of measurements, current clamps are used in operation, and additionally in voltage measurements from voltage transformers, where you have to take into account the fundamental, additional sources of errors discussed in the article. These errors and dispersion resulting from the production technology may fundamentally hinder the proper assessment of the technical condition, hence it is so important to properly recognize the listed basic sources of measurement uncertainty. In addition, the analysis should take into account three factors related to external conditions - temperature, voltage applied to the arrester and the content of higher harmonics in the supply voltage for which appropriate methods have been provided to determine the active component of the leakage current for reference conditions.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

We know that quantum logics are the most prominent logical systems associated to the lattices of closed Hilbert subspaces. But what does it happen if, following a quantum computing perspective, we want to associate a logic to the process of quantum registers measurements? This paper gives an answer to this question, and, quite surprising, shows that such a logic is nothing else that the standard propositional intuitionistic logic.

Non-destructive testing has many advantages, such as the ability to obtain a large number of data without destroying existing structures. However, the reliability of the estimation accuracy and the limited range of applicable targets remains an issue. This study proposes to a novel pin penetration test method to determine the early age compressive strength of concrete before demolding. The timing of demolding and initial curing are determined according to the strength development of concrete. Therefore, it is important to determine the compressive strength at the early age before demolding at the actual construction site. The applicability of this strength estimation methodology at actual construction is investigated. Small test holes (12 mm in diameter) are prepared on the mold surface in real construction sites and mock-up specimens in advance. The pin is penetrated into these test holes to obtain the relationship between the compressive strength and the penetration depth. As a result, it is confirmed that the pin penetration test method is suitable to measure the early age compressive strength at actual construction site. This allows the benchmark values for compressive strength, necessary to avoid early frost damage, to be directly verified on the concrete structural members at the construction site. For instance, the compressive strengths of greater than 5 MPa and 10 MPa can be confirmed by the penetration depths benchmark values of 8.0 mm and 6.7mm or less, respectively.

Bamboo is considered a sustainable construction material due to its ability to grow quickly and its mechanical properties that are comparable to timber. Contributing to the current effort to establish the structural bamboo standards in the National Structural Code of the Philippines (NSCP), this study establishes the characteristic compressive strength of four bamboo species: Bambusa vulgaris (36 samples), Dendrocalamus asper (36 samples), Bambusa blumeana (94 samples), and Guadua angustifolia Kunth (30 samples). The samples were subjected to compressive loading following ISO 22157-1 (2017). The characteristic compressive strength values obtained, according to ISO 12122-1 (2014), were 40.35 MPa for B. vulgaris, 40.21 MPa for D. asper, 46.63 MPa for B. blumeana, and 36.99 MPa for G. angustifolia Kunth. Simple linear analysis, One-way ANOVA, and Welch’s t-Test were used to analyze the correlation models and establish a comparative analysis of the effect of nodes, and geometric and physical properties on the compressive strength of bamboos. Comparing the characteristic compressive strength obtained from this study to the strength of unseasoned structural timber of Philippine woods, all bamboo species showed higher strength values, and thus have great potential as an alternative construction material to timber.

This work combines compressive sensing and short word-length techniques to achieve localization and target tracking in wireless sensor networks with energy-efficient communication between the network anchors and the fusion center. Gradient descent localization is performed using time-of-arrival (TOA) data which are indicative of the distance between anchors and the target thereby achieving range-based localization. The short word-length techniques considered are delta modulation and sigma-delta modulation. The energy efficiency is due to the reduction of the data volume transmitted from anchors to the fusion center by employing any of the two delta modulation variants with compressive sensing techniques. Delta modulation allows the transmission of one bit per TOA sample. The communication energy efficiency is increased by RⱮ, R≥1, where R is the sample reduction ratio of compressive sensing and Ɱ is the number of bits originally present in a TOA-sample word. It is found that the localization system involving sigma-delta modulation has a superior performance to that using delta-modulation or pure compressive sampling alone, in terms of both energy efficiency and localization error in the presence of TOA measurement noise, owing to the noise shaping property of sigma-delta modulation.

Predetermined physical properties cannot manifest at the same time if they are mutually exclusive. As part of a single system, they become observable at different times, in sequence. In this case, pairwise detections in a narrow window of coincidence allow for maximal Bell violations (S=4 for the CHSH protocol), without room for doubt about the local nature of the process. This shows that a deeper description of physical reality is possible, as suggested by Einstein, Podolsky and Rosen. Though, a more inclusive definition of Realism is required, in order to account for Bohr’s Contextuality.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Subsurface temperature is the key parameter in geothermal exploration. An accurate estimation of the reservoir temperature is of high importance and usually done either by interpolation of borehole temperature measurement data or numerical modeling. However, temperature measurements at depths which are of interest for deep geothermal applications (usually deeper than 2 km) are generally sparse. A pure interpolation of such sparse data always involves large uncertainties and usually neglects knowledge of the 3D reservoir geometry or the rock and reservoir properties governing the heat transport. Classical numerical modeling approaches at regional scale usually only include conductive heat transport and do not reflect thermal anomalies along faults created by convective transport. These thermal anomalies however are usually the target of geothermal exploitation. Kriging with trend does allow including secondary data to improve the interpolation of the primary one. Using this approach temperature measurements of depths larger than 1,000 m of the federal state of Hessen/Germany have been interpolated in 3D. A 3D numerical conductive temperature model was used as secondary information. This way the interpolation result reflects thermal anomalies detected by direct temperature measurements as well as the geological structure. This results in a considerable quality increase of the subsurface temperature estimation.

Abstract: In recent years, the construction engineering sector has undergone a transformative shift towards the integration of machine learning (ML) techniques, particularly in predicting the properties of steel fiber-reinforced concrete (SFRC). Despite the theoretical sophistication of existing models, a persistent challenge remains – their opacity, lacking transparency and real-world relevance for practi-tioners. To address this gap and advance our current understanding, this study employs the extra gradient (XG) Boosting algorithm, crafting a comprehensive ap-proach. Grounded in a meticulously curated database drawn from 43 seminal pub-lications, encompassing 420 distinct records, this research focuses predominantly on three primary fiber types: crimped, hooked, and mil-cut. Complemented by hands-on experimentation involving 20 diverse SFRC mixtures, this empirical campaign is further illuminated through the strategic use of Partial Dependence Plots (PDPs), revealing intricate relationships between input parameters and con-sequent compressive strength. A pivotal revelation of this research lies in the identification of optimal SFRC formulations, offering tangible insights for real-world applications. The developed ML model stands out not only for its sophistication but also its tangible accuracy, evidenced by exemplary performance against inde-pendent datasets, boasting a commendable mean target-prediction ratio of 99%. To bridge the theory-practice gap, we introduce a user-friendly digital interface, thri-ughly designed to guide professionals in optimizing and accurately predicting the compressive strength of SFRC. This research thus contributes to the construction and civil engineering sectors by enhancing predictive capabilities and refining mix designs, fostering innovation, and addressing the evolving needs of the industry.

This paper discusses the tectonics of the St. Peter and St. Paul Archipelago (SPSPA) in the Equato-rial Atlantic Ocean, based on the joint-system geometry which show a North-South shorten-ing/transpressional uplift tectonism, is active leading to exhumation of the sub-oceanic mantle. These islets are the summits of a sigmoidal submarine ridge formed by mantle ultramafic rocks. The ridge is crossed by the principal transform deformation zone of the northern transform fault of the St. Paul Multifault System. The South flank ridge exposes serpentinized mantle perido-tites, while the North flank exposes strongly deformed/fractured ultramylonites, recording duc-tile and brittle deformation at lithospheric conditions. The SPSPA show multiple joint systems cutting mylonitic foliation of the exposed rocks, forming three main families: high-angle paral-lel joints of tectonic origin, serpentinization-related joints with random direction and load-release low-angle parallel joints. The tectonic joints show an average direction of N31°E and N28°W, forming a conjugate system with a N1ºW compression axes, coherent with a trans-pressive stress field. Accordingly, the earthquakes focal mechanism close to the islets also shows N-S compression. The previously reported active uplift with an average rate of 1.5 mm/year and the directions of the joint system here reported agreeing with a present-day active N-S compres-sive field at a high angle with the direction of the transform fault.

This study aims to model grinding of a Polish slag and evaluate the particle size distributions of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e. temperature, curing and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin-Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multi fractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

The study was conducted on a cohort of 16 subjects, who were monitored with infrared images captured from their hands, following a specific protocol established by a preliminary analysis. Experimental results revealed that thermography can detect focal points and regions exhibiting either hyper- or hypo-thermia across the skin surface and muscular regions. This capability allows for extracting and categorizing precise medical data, difficult to determine during the early stages of the disease, thus facilitating ongoing monitoring efforts and early diagnosis in Parkinson research.

Virtual validation of radar sensor models is becoming increasingly important for the safety validation of adf. Therefore, methods for quantitative comparison of radar measurements in the context of model validation need to be developed. This paper presents a novel methodology for accessing and quantifying validation measurements of radar sensor models. This method uses edf and the so-called dvm to effectively quantify deviations between distributions. By applying this metric, the study measures the consistency, reproducibility and repeatability of radar sensor measurements. Different interfaces and different levels of detail are investigated. By comparing the radar signals from real world experiments where different objects are present, valuable insights are gained into the performance of the sensor. In particular, the research extends to assessing the impact of varying rain intensities on the measurement results, providing a comprehensive understanding of the sensor’s behaviour under these conditions. This holistic approach significantly advances the evaluation of radar sensor capabilities and enables the quantification of the maximum required quality of radar simulation models.

In recent years, the concept of Fiducial Reference Measurements (FRM) has been developed to highlight the need for precise and well-characterised measurements tailored explicitly to the post-launch calibration and validation (Cal/Val) of Earth observation satellite missions. The confidence that stems from robust unambiguous uncertainty assessment of space observations is fundamental to assessing the changes in the Earth system and climate model prediction, and delivering the essential evidence-based input for policy makers and society striving to mitigate and adapt to climate change. The underlying concept of an FRM has long been a core element of a Cal/Val program, providing a ‘trustable’ reference against which performance can be anchored or assessed. The ‘FRM’ label was created to embody into such a reference a set of key criteria. These criteria included the establishment of documented evidence of uncertainty with respect to a community-agreed reference (ideally SI-traceable) and specific tailoring to the needs of a satellite mission. It, therefore, facilitates comparison and interoperability between products and missions in a cost-efficient manner. CEOS Working Group Cal/Val (WGCV) is now putting in place a framework to assess the maturity and compliance of a ‘Cal/Val reference measurement’ in terms of a set of community-agreed criteria which define it to be of CEOS-FRM quality. The assessment process is based on a maturity matrix that provides a visual assessment of the state of any FRM against each of a set of given criteria; making visible where it is mature and where evolution and effort needs to be done. This paper provides the overarching definition of what constitutes an FRM and introduces the new CEOS FRM assessment framework.

The EPR paradox was caused by the provision that quantum variables must have pre-existing values. This type of “hidden property realism” was later falsified by Bell’s Theorem. Yet, modern interpretations of quantum entanglement still insist on the reality of pre-existing properties, whether explicitly or implicitly. Instead, they treat Bell’s inequality as a Locality Criterion. This is a questionable practice, considering that classical joint measurements also violate such inequalities for mutually exclusive wave properties. In particular, consecutive measurements of polarization produce the same coefficients of correlation as parallel measurements with polarization-entangled quanta, yet they are explicitly local. Nonetheless, they also require nonlocal interpretations if pre-existing properties are taken for granted. The solution is to reject the models with pre-existing properties for both classical and quantum wave-like phenomena.

This work communicates laser-plasma experiments in a gaseous mixture of hydrogen and nitrogen. Time-resolved spectroscopy measures the first four Balmer series hydrogen lines together with selected neutral and ionized nitrogen lines. Optical breakdown plasma is generated in a 1:1 hydrogen:nitrogen mixture at ambient temperature and 0.27-atm pressure. Time-resolved spectroscopy records emitted radiation with spatial resolution along the slit height for the H_α, H_β, H_γ, and H_δ lines. For 13 selected time delays from 0.25 µs to 3.25 µs and 0.025 µ gate-widths, micro-plasma diagnostics is evaluated. Of interest are the peak-separation and width of H_δ and width of H_γ for electron densities in the range of 0.1 to 1.0×10¹⁷ cm^-3, and comparisons with H_β and H_α diagnostics. Integral inversions interrogate spatial distributions of the plasma expansion. Applications include laboratory and stellar astrophysics plasma diagnosis.

Artificial intelligence is increasingly used in various branches of engineering. In this article, artificial neural networks are used to predict the crush resistance of corrugated packaging. Among the analysed packages were boxes with ventilation openings, packages with perforations, and typical flap boxes, which makes the proposed estimation method very universal. Typical shallow feedforward networks were used, which are perfect for regression problems, mainly when the set of input and output parameters is small, so no complicated architecture or advanced learning techniques are required. The input parameters of the neural networks are selected so as to take into account not only the material used for the production of the packaging, but also the dimensions of the box and the impact of ventilation holes and perforations on the load capacity of individual walls of the packaging. In order to maximize the effectiveness of neural network training process, the group of input parameters was changed so as to eliminate those to which the sensitivity of the model was the lowest. This allowed the selection of the optimal configuration of training pairs for which the estimation error was on the acceptable level. Finally, models of neural networks were selected, for which the training and testing error did not exceed 10%. The demonstrated effectiveness allows to conclude that the proposed set of universal input parameters is suitable for efficient training of a single neural network model capable of predicting the compressive strength of various types of corrugated packaging.

In the modern world, all manufacturers strive for the optimal design of their products. This general trend is recently also observed in the corrugated board packaging industry. Colorful prints on displays, perforations in shelf-ready-packaging and various types of ventilation holes in trays, although extremely important for ergonomic or functional reasons, weaken the strength of the box. To meet the requirements of customers and recipients, packaging manufacturers outdo each other in new ideas for the construction of their products. Often the aesthetic qualities of the product become more important than the attention to maintaining the standards of the load capacity of the packaging (which, apart from their attention-grabbing functions, are also intended to protect transported products). The particular flaps design (both top and bottom) and their influence on the strength of the box is investigated in this study. The updated analytical-numerical approach is used here to predict the strength of the packaging with various flap’s offsets. Experimental results indicated a significant decrease in the static load-bearing capacity of packaging in the case of shifted flap creases. The simulation model proposed in our previous work has been modified and updated to take into account also this effect. The results obtained by the model presented in the paper are in satisfactory agreement with the experimental data.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Measuring reference evapotranspiration (ETo) is a difficult and costly process. Several parameters are needed to calculate it from meteorological parameters with the aid of some developed equations. There may be variable microclimates in some regions and these are often quite far from the climate stations. Therefore, for ETo, it is better to prefer local measurements rather than relying on regional values. ETo is of great importance for all water-related sectors. It is the primary factor designating the amount of irrigation water to be applied to the plant rootzone in agricultural activities. The amount of irrigation water to be applied is determined by correcting ETo value with the plant coefficient (kc) and irrigation efficiency. There have been many developments in measurement/calculation of ETo in recent years and it is expected that there will be more in the future. Within the scope of this study, ETo values measured with ETgage equipment were compared with the monthly ETo values calculated with the use of Thornthwaite, Blaney-Criddle, Cropwat (FAO Penman Monteith), Jensen-Haise and ASCE standardized Penman Monteith (ASCE SZ PM) methods. In terms of total ETo value, Thornthwaite (17%) and Jensen-Haise (14%) methods yielded lower values than ETgage readings. On the other hand, Blaney-Criddle (15%), Cropwat FAO PM (10%) and ASCE SZ PM (30%) methods yielded greater values than ETgage readings. Among the calculation methods, in Cropwat software, FAO PM equation yielded the closest value to ETgage readings. It was concluded based on present findings that ETgage equipment could reliably be used in determination of ETo.

The coast of Oman is observing huge coastal developments to materialize Oman Vision 2040 covering all the strategic sectors. Historical data of coastal hydrodynamic parameters is scarce, even though its importance for a proper design of coastal structures is recognized. Acoustic Doppler Current Profilers were deployed at eleven locations along the coast of Oman. These locations were selected based on their strategic importance for the country. The duration of deployment was from 60 to 265 days. The measured data of waves and current were collected and analyzed using the equipment-specific software and Excel. The significant wave heights can reach 2m along the whole coast of Oman. The southern coast is dominated by the swells. The maximum to significant wave height ratio is approximately 1.5 which is less than a value of 2 obtained using Rayleigh distribution. The coastal currents are stronger along the southern coast than those along the northern coast. The range of current magnitude is from 0.02 m/s to 0.8 m/s. This baseline study will help the public authorities in establishing permanent hydrodynamic measurement stations along the coast of Oman. Moreover, these measurements will serve the practicing engineers in designing coastal structures along the coast of Oman.

Biochemical oxygen demand (BOD) is one of the most important factors to consider when evaluating water contamination. BOD5 is the amount of oxygen consumed in five days by microorganisms that oxidize biodegradable organic materials in an aerobic biochemical manner. The primary objective of this effort is to use microbial fuel cells (MFCs) to shorten the time required for BOD5 measurements. We created a regression artificial neural network (AI), and the predictions we obtained for BOD5 measurements were taken over 6 – 24 hours with an average error of just 7%. The outcomes demonstrated by our AI MFC/BES BOD5 sensor’s viability for use in real-world scenarios.

The authors previously found a model of universal quantum computation by making use of the coset structure of subgroups of a free group $G$ with relations. A valid subgroup $H$ of index $d$ in $G$ leads to a \lq magic' state $\left|\psi\right\rangle$ in $d$-dimensional Hilbert space that encodes a minimal informationally complete quantum measurement (or MIC), possibly carrying a finite \lq contextual' geometry. In the present work, we choose $G$ as the fundamental group $\pi_1(V)$ of an exotic $4$-manifold $V$, more precisely a \lq small exotic' (space-time) $R^4$ (that is homeomorphic and isometric, but not diffeomorphic to the Euclidean $\mathbb{R}^4$). Our selected example, due to to S. Akbulut and R.~E. Gompf, has two remarkable properties: (a) it shows the occurence of standard contextual geometries such as the Fano plane (at index $7$), Mermin's pentagram (at index $10$), the two-qubit commutation picture $GQ(2,2)$ (at index $15$) as well as the combinatorial Grassmannian Gr$(2,8)$ (at index $28$) , (b) it allows the interpretation of MICs measurements as arising from such exotic (space-time) $R^4$'s. Our new picture relating a topological quantum computing and exotic space-time is also intended to become an approach of \lq quantum gravity'.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

We propose a novel approach to quantum theory construction that involves solving a maximization problem on the Shannon entropy of all possible measurements of a system, relative to its initial preparation. This maximization problem is additionally constrained by a phase condition that vanishes under measurements. Specifically, enforcing a vanishing U(1)-valued phase constraint leads to standard quantum mechanics, while a vanishing Spin^c(3,1)-valued phase constraint extends the theory to relativistic quantum mechanics and to quantum gravity. The latter scenario is found to incorporate the SU(3)xSU(2)xU(1) symmetries of the Standard Model as invariants of the probability measure itself, and to construct the metric tensor as an operator via a double-copy mechanism applied to Dirac currents. Significantly, this solution is consistent exclusively with a 3+1-dimensional spacetime configuration---all other dimensional settings are shown to lead to fundamental obstructions. This framework seamlessly integrates fundamental concepts from quantum mechanics, relativistic quantum mechanics, quantum gravity, the dimensional specificity of spacetime, and particle physics symmetries as the solution to a simple entropy maximization problem.

A method of accuracy error compensation for the time interval is examined, allowing to eliminate the dependence of accuracy error on the duration of measured intervals and minimising the influence of destabilising factors - ambient temperature changes and the initial deviation of the meter clock generator frequency from the nominal value. The compensation method is based on a calibration procedure that measures precise time intervals under conditions of changing ambient temperature. Then the dependence of the accuracy error on temperature for a particular meter is recorded. Based on these data, a correction table is compiled containing correction factors and temperature values at which these factors were determined. Under real measurement conditions, the correction factor corresponding to the current temperature is determined from the table for measured results correction. The table with correction factor values could be stored in the memory of the meter or processing computer. Experimental verification of the method showed that applying a correction for a meter with a standard XO class clock generator (certificated instability of ±50 ppm) can obtain an equivalent clock generator instability of ±0.15 ppm. The application of the method is efficient in cases where the use of high-end clocking to ensure the required measurement accuracy is not economically feasible.

Abstract: Windtech device is a novel tool for measuring the sensation of the ‘cold’. Cold poses numerous challenges for industrial operations, human survival, and living convenience. The impact of the cold is not possible to be quantified just based on temperatures; however other factors such as wind speed, humidity, irradiance have to be taken into consideration. Efforts have been made to develop combined indices such as wind chill temperature (WCT), AccuWeather RealFeel®, and others. The presented article discusses these along with the industrial standards that emphasize on the quantification of the ‘cold’. The following article introduces the Windtech device and its operating principle involving ‘heated temperature’, where the ‘heated temperature’ is affected by environmental parameters including ambient temperature, humidity, wind velocity, and irradiance. The discussed Windtech device is calibrated for operation according to the ISO 11079:2007 standard.

Ion association is an important process in aqueous dissolution, precipitation, and~crystallization of ionic inorganic, organic, and biological materials. Polyoxometalates (POMs) are good model compounds for understanding the complex relationships between lattice energy, ion-pairing in solution, and salt solubility. Here we perform calorimetric measurements to elucidate trends in cluster stability, lattice energy, and ion-pairing behavior studies of simple hexatantalate salts in neat water, parent hydroxide solutions, and molybdate melts, extending previous studies on the isostructural hexaniobates. High temperature calorimetry of alkali salts of hexatantalate reveals that the enthalpies of formation from oxides of the K, Rb, and Cs salts are more similar to each other than they are for their niobate analogues and that the tantalate cluster is energetically less stable than hexaniobate. Aqueous dissolution calorimetry reveals that the cesium salt of hexatantalate has a similar concentration dependence on its dissolution enthalpy to that of hexaniobate. However, unlike~rubidium hexaniobate, rubidium hexatantalate also exhibits increased concentration dependence, indicating that hextantalate can undergo increased ion-pairing with alkali salts other than cesium, despite the dilute environments studied. Dissolution enthalpies of POM salts in the parent alkali hydroxides shows that protonation of clusters stabilizes lattices even more than the strongly associating heavy alkali cations do. Additionally, neither weak nor strong lattice ion associations necessarily correlates with respectively high or low aqueous solubility. These studies illuminate the importance of considering ion-pairing among the interrelated processes in the aqueous dissolution of ionic salts that can be extended to serving as a model of cation association to metal oxide surfaces.

In this manuscript we are investigating the contribution of dynamic membrane properties of phospholipid membranes to coherent scattering signals under grazing incidence. Spectroscopic measurements under grazing incidence can provide useful insight into the properties of biological membranes, however are often impeded by weak signals. By using grazing-incidence small-angle neutron scattering (GISANS) to identify a dynamic scattering contribution we are able to independently corroborate the existence of a previously found dynamic mode found by grazing-incidence neutron spin echo spectroscopy (GINSES). Additionally, by increasing the speed of measurement compared to GINSES from several days to hours we were able to explore the temperature behavior of this mode in phospholipid membranes. These dynamic modes of the membranes show a wavelength of around 700 Å in-plane of the membrane and are most pronounced around 37°C and strongly decrease at lower temperatures below 25°C before vanishing at 20°C. We therefore speculate that they may be linked to biologically relevant functions of the membranes themselves.

Carbon monoxide (CO) concentrations in wildfire plumes are easily measured from satellites. This gas can be used as a proxy for carbon dioxide. Forest fires play an important role in the carbon balance and in particular the CO balance. The most likely causes of mega-fires of 2003, 2012, 2021, and 2023 in the Northern hemisphere are heat waves and severe droughts associated with changes in general circulation. Here we analyze satellite data obtained by two different sounders, AIRS and TROPOMI. Different sensitivity to the lowest troposphere allows obtaining information about anthropogenic or pyrogenic contamination of the boundary layer. Shapes of areas polluted by mega-fires in 2019-2020 (Southeastern Australia) and 2021 (Central Siberia) coincide with the areas occupied by coal deposits. The Siberian Lena and Tunguska coal basins are the two largest coal fields in the world. In 2021, their combined area accounted for 90% of fire CO emission from the entire Russian Federation. So strong fires have not observed in this area before. Under- and sub-ground coal combustion may be included into the list of wildfire fuels, at least their role for ignition should be admitted. Further research is needed to assess the importance of coal fires to global climate.

The authors recently proposed a method for on-site dosimetry by a combination of radiochromic film and portable colorimeter. To test and expand the applicability of this method, dosimetric properties of radiochromic reactions were examined for six combinations of two popular Gafchromic films (EBT3 and EBT-XD) and three commercially-available portable colorimeters (nix pro2, nix spectro2 and Spectro1 Pro; abbreviated to “NixP”, “NixS” and “SpoP”, respectively). EBT3 and EBT-XD were irradiated with 160 kV X-rays at 0.3 to 40Gy and 1 to 80 Gy, respectively, and the radiation-induced color levels of RGB and CMMK components were measured with the three colorimeters. Angle dependence was examined by reading at 15° intervals. As results, it was judged that all combinations would work effectively as tools for on-site dosimetry. NixP and NixS showed advantages that they were applicable to a wider dose range for both films, while Spo1 worked better in a lower dose range. On the other hand, Spo1 had an advantageous feature of no angular dependence in reading films, while NixP and NixS showed significant angle-dependent changes. These differences were presumed to attribute to the different geometries of LED light emission; it came from all directions (ring-shape source) in Spo1, 4 directions in NixP, and 8 directions in NixS. These findings would expand the applicability of the proposed on-site dosimetry method to various occasions.

The paper presents the first retrievals of clean snow properties using spaceborne hyperspectral The Environmental Mapping and Analysis Program (EnMAP) observations. The location close to the Dome C in Antarctica has been selected. At this location the atmospheric effects except molecular light scattering and absorption are weak and the simplified atmospheric correction scheme can be applied. The ice grain size, snow specific surface area and snow spectral and broadband albedos have been retrieved using single view EnMAP measurements. In addition, we propose the technique to retrieve trace gas concentrations (e.g., water vapor, ozone) from EnMAP observations over the snow surfaces. Close correspondence of satellite and ground measured parameters has been found.

We provide quantitative results from GIS-based modelling of urban emission functions for a range of representative low- and mid-rise locations, ranging from individual streets to residential communities within cities as well as entire towns and city regions with the aim of whether lantern photometry or built environment has the dominant effect on light pollution. We demonstrate the scalability of our work by providing results for the largest urban area modelled to date, comprising the central 117 km2 area of Dublin City and containing nearly 42,000 public lights. Our results show a general similarity in the shape of the azimuthally-averaged emission function for all areas examined, with differences in total light output distribution depending primarily on the nature of the lighting and, to a smaller extent, on the obscuring environment including seasonal foliage effects. A comparison with global satellite observations shows that they are consistent with the deduced angular emission function for other low-rise areas worldwide. We further validate our approach by comparing results for a range of urban locations by the close agreement observed in a detailed comparison of with calibrated imagery from the International Space Station. To our knowledge, this is the first such detailed quantitative verification of light loss calculations.

Beer fermentation is typically monitored by periodic sampling and off-line analysis. In-line sensors would remove the need for time-consuming manual operation and provide real-time evaluation of the fermenting media. This work uses a low-cost ultrasonic sensor combined with machine learning to predict the alcohol concentration during beer fermentation. The highest accuracy model (R2=0.952, MAE=0.265, MSE=0.136) used a transmission-based ultrasonic sensing technique along with the measured temperature. However, the second most accurate model (R2=0.948, MAE=0.283, MSE=0.146) used a reflection-based technique without the temperature. Both the reflection-based technique and the omission of the temperature data are novel to this research and demonstrate the potential for a non-invasive sensor to monitor beer fermentation.

Thermal interface material (TIM) that can exist as liquid at the service temperature enables efficient heat transfer across two adjacent surfaces in electronic applications. In this work, the thermal conductivities of different phase regions in the Ga-In system at various compositions and temperatures are measured for the first time. A modified comparative cut bar technique is used for the measurement of the thermal conductivities of In_xGa_1-x (x=0, 0.1, 0.214, 0.3, and 0.9) alloys at 40, 60, 80, and 100^oC that are the temperatures commonly encountered in consumer electronics. The thermal conductivity values for the liquid and semi-liquid (liquid+β) Ga-In alloys are higher than the TIM currently used in consumer electronics. These measured quantities, along with the available experimental data from the literature, served as input for the thermal conductivity parameter optimization using the CALPHAD (CALculation of PHase Diagram) method for the pure elements, solution phase, and two-phase region. A set of self-consistent parameters for the description of the thermal conductivity of the Ga-In system is obtained. There is good agreement between the measured and calculated thermal conductivity values for all the phases. Hence, it can be envisaged that liquid/semi-liquid Ga-In alloys can be considered as a potential TIM in consumer electronics due to its high thermal conductivity.

Abstract: To overcome the environmental impact of cement production in cocnrete , the construction industry is adopting eco-friendly approaches, such as incorporating alternative and recycled materials, minimizing carbon emissions in concrete production. One such material that has gained prominence is Ground Granulated Blast Furnace Slag (GGBFS),. This study focuses on investigating the compressive strength of concrete at 28 days of age by examining the influences of several factors, such as temperature, water-to-binder ratio (w/b), GGBFS-to-binder ratio (GGBFS/b), fine aggregate, coarse aggregate, and superplasticizer. A statistical modeling approach was employed to comprehensively analyze these parameters and assess their impact on the compressive strength. To accomplish this, the study collected and analyzed data from the literature, resulting in a dataset of 210 observations. The dataset was divided into training and testing groups, and statistical analyses were performed to assess the relationships between the input parameters and compressive strength. The correlation analysis revealed insignificant relationships between the input parameters and compressive strength, indicating that multiple factors affect the strength. Different models, such as linear regression, nonlinear regression, quadratic, full quadratic models, and artificial neural networks (ANN) were employed to predict the compressive strength. The findings of this study contribute to a better understanding of the factors that influence the compressive strength of concrete containing GGBFS. The results underscore the importance of considering multiple parameters to predict strength accurately.

Background: Despite the tremendous effort in hamstring injury prevention, injury rates in soccer remain elevated. Hypothesis: Hamstring and hip/pelvic isometric strength imbalances may increase the likelihood of hamstring strain injury (HSI) occurrence amongst soccer players.Study design: Case-control study.Methods: In 120 male soccer players (mean age: 20.0 +/- 6.96 years) pre-season maximum isometric strength of the hip adductors, abductors, flexors, and knee flexors were measured, and strength ratios were calculated. Previous injury and anthropometric data were registered. Injury data were collected following the FIFA/UEFA consensus. A multivariate and Machine learning-based Logistic Regression model was employed to estimate the likelihood of players sustaining a hamstring injury.Results: 21 players sustained 32 hamstring injuries. Players with higher abduction strength in the dominant leg had an 18.5% lower risk of sustaining a hamstring injury (OR = 0.818, CI 95% = [(0.695-0.964]). No other significant contributor variables were found to be significant predictors of hamstring injury in the player group (p> 0.05).Conclusion: Isometric strength of the abductor muscles in the dominant limb had a significant association with hamstring injury.Clinical relevance: Our findings indicate the utilization of hip strength measurements as an integral component of the pre-season screening assessment, thereby affirming prior research on the correlation between lumbo-pelvic stability and incidence of hamstring injuries. Consequently, clinicians should contemplate incorporating hip strengthening exercises into regular training sessions, rehabilitation programs, and injury prevention protocols especially indicated when lower hip strength levels are observed.

In this work, we explore new constraints on phantom scalar field cosmologies with a scalar field employing early times catalogues related to CMB measurements, along with the local standard observables, like Supernovae Type Ia (SNIa), H(z) measurements (Cosmic Clocks), and Baryon Acoustic Oscillations (BAO) baselines. In particular, we studied a tracker phantom field with hyperbolic polar coordinates that have been proposed in the literature. The main goal is to obtain precise cosmological constraints for H0 and σ8, in comparison to other constructions that present tension in early cosmological parameters. Our results show that phantom scalar field cosmologies have a reduced statistical tension on H0 that it is less than 3σ using model-independent CMB catalogues as SPT-3G+WMAP9 and ACTPol DR-4+WMAP9 baselines. This suggests these models using a different phantom potential might address the Hubble constant problem and reduce the systematics involved.

Significant advances in Penning trap measurements of atomic masses and mass ratios of the proton, deuteron, triton, helion, and alpha-particle have occurred in the last five years. These include a measurement of the mass of the deuteron against 12C with 8.5 x 10-12 fractional uncertainty; resolution of vibrational levels of H2+ as mass and the application of a simultaneous measurement technique to the H2+/D+ cyclotron frequency ratio, yielding a deuteron-proton mass ratio at 5 x 10-12; new measurements of HD+/3He+, HD+/T+ and T+/3He+ leading to a tritium beta-decay Q-value with an uncertainty of 22 meV, and atomic masses of the helion and triton at 13 x 10-12; and a new measurement of the mass of the alpha-particle against 12C at 12 x 10-12. Some of these results are in strong disagreement with previous literature values. Their impact in determining a precise proton/electron mass ratio and electron atomic mass from spectroscopy of the HD+ molecular ion is also discussed.

This study introduces an alternative to the existing methods for measuring ocean currents based on a recently developed technology. The SailBuoy is an unmanned surface vehicle powered by wind and solar panels that can navigate autonomously to predefined way-points and record velocity profiles using an integrated downward-looking Acoustic Doppler Profiler (ADCP). Data, collected on two validation campaigns, shows a satisfactory correlation between the SailBuoy current records and traditional observation techniques such as bottom mounted and moored current profilers and moored single-point current meter. While the highest correlations were found in tidal signals, strong current, and calm weather conditions, low current speeds and varying high wave and wind conditions reduced correlation considerably. Filtering out some events with high sea surface roughness associated with high wind and wave conditions may increase the SailBuoy ADCP listening quality and lead to better correlations. Not yet resolved is a systematic offset between the measurements obtained by the SailBuoy and the reference instruments of ± 0.03 m/s. Possible reasons are discussed to be the differences between instruments (various products) as well as changes in background noise levels due to environmental conditions.

The article aims to present the possible use of the simple modified optical training kit as a low-cost, simple setup for high precision surface speed measurements. A measurement capability evaluation of the optical Doppler kit used for velocimetry of a fast-rotating reflecting surface is presented. To get high repeatability measurements, we modified a fibre optic interferometry training kit. By using signal processing and statistics a precision under repeatability conditions of measurements was evaluated. Expressed by the standard deviations (3σ’s) the surface velocity measurements precision below 0.2 m/s is shown. The Cg’s capability indices were also evaluated. We postulate, the electric circuit stability of the measurement system power supply is essential for a signal noise reducing process for a wide range of metrology systems. It is crucial for precision measurements.

The interest in dry EEG electrodes has increased in recent years and especially as everyday suitability earplugs for measuring drowsiness or focus of auditory attention. However, the challenge is still the need for a good electrode material, which is reliable and can be easily processed for highly personalized applications. Laser processing as used here is a fast and very precise method to produce personalized electrode configurations that meet the high requirements of in-ear EEG electrodes, for example. The arrangement of the electrodes on the very flexible and compressible mats allows an exact alignment of the electrodes to the ear mold and contributes to a high wearing comfort, as no edges or metal protrusions are present. For better transmission properties, an adapted coating process for surface enlargement of platinum electrodes is used, which allows easy control of the thickness and growth form of the porous layer. The porous platinum-copper alloy is chemically very stable, shows no exposed copper residues and enlarges the effective surface area by 40. In a proof-of-principle experiment, these porous platinum electrodes could be used to measure the Berger effect in a dry state using just one ear of a test person. Their signal-to-noise ration and frequency transfer function is comparable to gel-based silver/silver chloride electrodes.

Solar radiation corresponds to fundamental parameters for solar photovoltaic (PV) technology. Reliable solar radiation prediction became valuable to design solar PV systems, performance, operatively efficient planning, safety operation, grid dispatch and financial characteristics. However, high quality ground-based solar radiation measurements are scarce, especially for very short-term time horizon. Most of the existent studies trained the machine learning (ML) model used dataset with time horizon of 1-hour or day, very fewer studies have been reported using a dataset with a 1-mitute time horizon. In this study, a comprehensive evaluation of nine ensemble learning algorithms (ELA) is performed to estimate the solar radiation in Santo Domingo with a 1-minute time horizon dataset collected from a local weather station. The ensemble learning evaluated included seven homogeneous ensembles; Random Forest (RF), Extra Tree (ET), Adaptive Gradient Boosting (AGB), Gradient Boosting (GB), Extreme Gradient Boosting (XGB), Light Gradient Boosting (LGBM), Histogram-based Gradient Boosting (HGB) and heterogeneous ensemble named as Voting and Stacking. RF, ET, GB, HGB were combined to develop Voting and Stacking and Linear Regression (LR) was adopted in the second layer of the Stacking. Five technical metrics, Mean Squared Error (MSE), Root Mean Squared Error (RMSE), Mean Absolute Error (MAE), Mean Absolute Percentage Error (MAPE) and Coefficient of Determination (R2) were used as criteria to determine the prediction quality of the developed ensemble algorithms. Comparison of the results indicates that the HGB algorithm offers superior prediction performance among the homogeneous ensemble learning and overall, the Stacking provides the best accuracy with metric values of MSE=3218.27, RMSE= 56.73, MAE=29.87, MAPE=10.60, R2=0.964.

Measurements of optical properties have been used for decades to study particle distributions in the ocean. They have been found useful to constrain suspended mass concentration as well as particle-related properties such as size, composition, packing (particle porosity or density) and settling velocity. Optical properties, however, provide measurements that are biased, as certain particles (based on size, composition, shape or packing) contribute to a specific property more than others. Here we study this issue both theoretically as well as by contrasting different optical properties collected simultaneously in a bottom boundary layer, to highlight the utility of such measurements as well as the biases we are likely to encounter using different optical properties to study suspended particles. In particular, we investigate the possibility to infer settling velocity from vertical profiles of optical measurements, finding that the effects of aggregation dynamics can seldom be ignored.

A new approach to the measurement with elastic lidar of depolarization produced by atmospheric aerosols is presented. The system uses two different telescopes: one for depolarization measurements and another for total-power measurements. The system architecture and principle of operation are described. The first experimental results are also presented, corresponding to a collection of atmospheric conditions over the city of Barcelona.

A study is made of the progressive ‘decoherence’ of cosmic ray extensive air shower particle detector signals in small air showers through measurements of coincidence rates for pairs of detectors versus the detector separation. Measurements are made both when only the two separated detectors themselves trigger in coincidence, and when that coincidence trigger also requires the detection of a local air shower by a small external air shower array. The addition of the explicit air shower trigger ensures that the latter data correspond to showers of a larger particle size, and triggering by very localised shower cores is then unlikely. When including a shower trigger, the decoherence results appear substantially different in form. The coincidence rate between two detectors only can be approximated by a power law variation with separation distance. When triggering involves an air shower array, the variation becomes close to an exponential form with characteristic exponent distances varying systematically with increasing detector and air shower size thresholds. A result is that one can see that small air showers will exhibit clear non-Poissonian density fluctuations near their cores out to distances of ~5m, or at shower energies below ~0.05 PeV. These ideas can be helpful in understanding the statistical properties of signals when using large detectors in air shower arrays.

The thermal properties of a building envelope are key indicators of the energy performance of the building. Therefore, methods are needed to determine quantities like U-values or heat capacitance in a fast, reliable way and with as little impact on the use of the building as possible. In this paper a technique is proposed that relies on a simplified electrical analogical model of building envelope components which can cover their dynamic thermal behavior. The parameters of this model are optimized to produce the best fit between simulated and measured outside surface temperatures. As the temperatures can be measured remotely with an infrared camera this approach requires significantly less installation effort and intrusion in the building than other methods. At the same time, a single measurement provides data for a large range of locations on a facade or a roof. The paper describes the method and a first experimental implementation of it. The experiment indicates that this method has the potential to produce results which have an accuracy that is comparable to standardized reference methods.