We propose a novel data hiding method in an audio host with a compressive sampling technique. An over-complete dictionary represents a group of the watermark. Each row of the dictionary is a Hadamard sequence representing multiple bits of the watermark. Then, the singular values of segment-based host audio in a diagonal matrix multiply by the over-complete dictionary producing a lower size matrix. At the same time, we embed the watermark into the compressed audio. In the detector, we detect the watermark and reconstruct the audio. This proposed method offers not only hiding the information but also compressing the audio host. The application of the proposed method is a broadcast monitoring and biomedical signal recording. We can mark and secure the signal content by hiding the watermark inside the signal while we compress the signal for memory efficiency. We evaluate the performance in terms of payload, compression ratio, audio quality, and watermark quality. The proposed method can hide the data imperceptibly, in range 729-5292 bps with compression ratio 1.47-4.84 and perfect detected watermark.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Statistical denoising techniques have been well studied, however many challenges still remain. This 9 article focuses on determining the least necessary number of significant samples in a statistical pop-10 ulation sampling, while minimizing the impact on the statistical detection of the fiber Bragg grating 11 (FBG) power spectra. This is achieved by using Bayesian decision making, small population statis-12 tics while excluding false detection. First, we investigate the impact of two-sided sliding window 13 technique applied near the cell under the test. The window size varies from 8 to 60 samples. The 14 considered maximum size of population sampling is connected with the number of wavelength 15 samples within the bandwidth of the symmetrical FBG power spectra peaks. Regarding the sym-16 metry of FBG power spectra peaks and the possible reduction of computational demands, we inves-17 tigate the impact of a one-sided sliding window. This enables to achieve less processing latency for 18 real time applications thus brings benefits to FBG-based fiber optical sensing. Both, two- and one-19 sided small population sampling techniques are then experimentally verified. Detection results are 20 analyzed in depth via calculating detection thresholds by using the small size window sliding along-21 side the waveband. From results achieved, it was found that the normality three-sigma rule does 22 not need to be followed while using the small population sampling. Experimental demonstrations 23 and analyses showed that the proposed concept of denoising and statistical threshold detection 24 based on the sliding window does not depend on the prior knowledge of probability distribution 25 functions of the FBG power spectra peaks level and background noise. We have also found that the 26 thresholds’ adaptability mainly depends on the statistical numerical characteristics of the above ad-27 ditive mixture of the FBG power spectra peaks signals and background noise.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

The systematic sampling is used as a method to get the quantitative results from the tissues and the radiological images. Systematic sampling on real line (R) is a very attractive method within which the biomedical imaging is consulted by the practitioners. For the systematic sampling on R, the measurement function (MF) is occurred by slicing the three-dimensional object equidistant systematically. The currently used covariogram model in variance approximation proposed by [28,29] is tested for the different measurement functions in a class to see the performance on the variance estimation of systematically sampled R. This study is an extension of [17], and an exact calculation method is proposed to calculate the constant λ(q,N) of confidence interval in the systematic sampling. The exact value of constant λ(q,N) is examined for the different measurement functions as well. As a result, it is observed from the simulation that the proposed MF should be used to check the performances of the variance approximation and the constant λ(q,N). Synthetic data can support the results of real data.

Wastewater-based surveillance is emerging as an important tool for COVID-19 pandemic trending. Current methods of wastewater collection, such as grab and auto-composite sampling, have drawbacks that impede effective surveillance, especially from small catchments with limited accessibility. Passive samplers, which are more cost-effective and require fewer resources to process, are promising candidates for monitoring wastewater for SARS-CoV-2. Here, we compared traditional auto sampling with passive sampling for SARS-CoV-2 detection in wastewater. Torpedo-style 3D printed passive sampler device containing both cotton swabs and electronegative filter membranes was used. Between April and June 2021, fifteen passive samplers were placed at a local hospital wastewater outflow alongside an auto sampler. Reverse transcription and quantitative polymerase chain reaction (RT-qPCR) was used to detect SARS-CoV-2 in the samples after processing and RNA extraction. The swab and membrane of the passive sampler showed similar detection rates and Ct values for SARS-CoV-2 RNA for the N1 and N2 gene targets. The passive method performed as well as the grab/auto sampling, with no significant differences between N1 and N2 Ct values. There were discrepant results on two days with negative grab/auto samples and positive passive samples, which might be related to the longer duration of passive sampling in the study. Overall, the passive sampler was rapid, reliable and cost-effective, and could be used as an alternative sampling method for the detection of SARS-CoV-2 in wastewater.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Background: Forecasting nonlinear stochastic systems most often is quite difficult, without giving in to temptations to simply simplify models for the sake of permitting simple computations. Objective: Here, two basic algorithms, Adaptive Simulated Annealing (ASA) and path-integral codes PATHINT/PATHTREE (and their quantum generalizations qPATHINT/qPATHTREE) are offered to detail such systems. Method: ASA and PATHINT/PATHTREE have been effective to forecast properties in three disparate disciplines in neuroscience, financial markets, and combat analysis. Applications are described for COVID-19. Results: Results of detailed calculations have led to new results and insights not previously obtained. Conclusion: These 3 applications give strong support to a quite generic application of these tools to stochastic nonlinear systems.

This study explores the prediction of concrete compressive strength using machine learning models, aiming to overcome the time-consuming and complex nature of conventional methods. Four models—Artificial Neural Network, Multiple Linear Regression, Support Vector Machine, and Regression Tree—are employed and compared for performance. Evaluation metrics such as Mean Absolute Deviation, Root Mean Square Error, Coefficient of Correlation, and Mean Absolute Percentage Error are used. After preprocessing 1030 samples, the dataset is split into 70% for training and 30% for testing. The ANN model, further divided into training, validation (15%), and testing (15%), outperforms others in accuracy and efficiency. This outcome streamlines compressive strength determination in the construction industry, saving time and simplifying the process.

Compressive sensing (CS) is a technique that allows a signal vector to be reconstructed with a number of linear measurements far fewer than its size. In this study, optical hybrid cryptography with simultaneous compressive sensing based on orthogonal matching pursuit (OMP) is proposed as an alternative solution to the two important problems in communications, namely, effective / efficient / signal processing and secure encryption/decrypton. The whole system is able to both compress and encrypt data with attack immunity.

We derive a concentration inequality for the uncertainty in the mean computed by stratified random sampling, and provide an online sampling method based on this inequality. Our concentration inequality is versatile and considers a range of factors including: the data ranges, weights, sizes of the strata, the number of samples taken, the estimated sample variances, and whether strata are sampled with or without replacement. Sequentially choosing samples to minimize this inequality leads to a online method for choosing samples from a stratified population. We evaluate and compare the effectiveness of our method against others for synthetic data sets, and also in approximating the Shapley value of cooperative games. Results show that our method is competitive with the performance of Neyman sampling with perfect variance information, even without having prior information on strata variances. We also provide a multidimensional extension of our inequality and discuss future applications.

Compressive sensing originates in the field of signal processing and has recently become a topic of energy-efficient data gathering in wireless sensor networks. In this paper, we propose an energy efficient distributed compressive sensing solution for sensor networks. Proposed solution utilizes sparsity distribution of signals to group sensor nodes into several coalitions and then implements localized compressive sensing inside coalitions. This solution improves data-gathering performance in terms of both data accuracy and energy consumption. The approach curbs both data-transmission costs and number of measurements. Coalition-based data gathering cuts transmission cost, and the number of measurements is reduced by scheduling sensor nodes and adjusting their sampling frequency. Our simulation showed that our approach enhances network performance by minimizing energy cost and improving data accuracy.

Distributed tracing is a cutting-edge technology for monitoring, managing, and troubleshooting native cloud applications. It offers a more comprehensive and continuous observability, surpassing traditional logging methods, and is indispensable for navigating modern complex software architectures. However, the sheer volume of generated traces is staggering in distributed applications, and direct storage and utilization of every trace are impractical due to associated operational costs. This entails a sampling strategy to select which traces warrant storage and analysis. Historically, sampling methods have included a rate-based approach, often relying heavily on a manual configuration. There is a need for a more intelligent approach, and we propose a hierarchical sampling methodology to address multiple requirements concurrently. Initial rate-based sampling mitigates the overwhelming volume of traces, as no further analysis can be performed on this level. In the next stage, more nuanced analysis is facilitated based on the previous foundation, incorporating information regarding trace properties and ensuring the preservation of vital process details even under extreme conditions. This comprehensive approach not only aids in the visualization and conceptualization of applications but also enables more targeted analysis in later stages. As we delve deeper into the sampling hierarchy, the technique becomes tailored to specific purposes, such as simplifying application troubleshooting. In this context, the sampling strategy prioritizes the retention of erroneous traces from dominant processes, thus facilitating the identification and resolution of underlying issues. The focus of this paper is to reveal the impact of the sampling on troubleshooting efficiency. Leveraging intelligent and explainable artificial intelligence solutions enables the detection of malfunctioning microservices and provides transparent insights into root causes. We advocate for using rule-induction systems, which offer explainability and efficacy in decision-making processes. By integrating advanced sampling techniques with machine learning-driven intelligence, we empower organizations to navigate the complexities of large-scale distributed cloud environments effectively.

This article examines air sampling as an environmental surveillance strategy for early pathogen detection and offers a preliminary comparison of air and wastewater surveillance. Air sampling involves collecting bioaerosols to analyze the microbial composition of the air, utilizing techniques like PCR and metagenomic sequencing. Air sampling appears especially promising for detecting respiratory pathogens and highly transmissible pandemic agents, as these spread primarily via aerosols and droplets. The article details various air sampling techniques, their efficiency, and practical considerations, categorizing them into filtration, impaction, impingement, electrostatic precipitation, and condensation methods. It also explores the composition of airborne microbes, emphasizing the low concentration of viral nucleic acids and the challenges this poses for metagenomic sequencing. The selection of sampling locations, including indoor environments and airplanes, is discussed as critical for effective pathogen detection. Finally, the article contrasts air and wastewater sampling, concluding that while both methods should ideally be explored as layered defenses, air sampling does not collectively appear more promising than wastewater sampling.

Dermal interstitial fluid (ISF) is a novel source of biomarkers that can be considered as an alternative to blood sampling for disease diagnosis and treatment. Nevertheless, in vivo extraction and analysis of ISF are challenging. On the other hand, microneedle (MN) technology can address most of the challenges associated with dermal ISF extraction and is well-suited for long-term, continuous ISF monitoring as well as in situ detection. In this review, we first briefly summarise the different dermal ISF collection methods and compare them with MN methods. Next, we elaborate on the design considerations and biocompatibility of MNs. Subsequently, the fabrication technologies of various MNs used for dermal ISF extraction, including solid MNs, hollow MNs, porous MNs and hydrogel MNs, are thoroughly explained. In addition, different sensing mechanisms of ISF detection will be discussed in detail. Subsequently, we identify the challenges and propose the possible solutions associated with ISF extraction. A detailed investigation is provided for the transport and sampling mechanism of ISF in vivo. Also, the current in vitro skin model integrated with the MN arrays will be discussed. Finally, future directions to develop a point-of-care (POC) device to sample ISF are proposed.

Background: Forecasting nonlinear stochastic systems most often is quite difficult, without giving in to temptations to simply simplify models for the sake of permitting simple computations. Objective: Here, two basic algorithms, Adaptive Simulated Annealing (ASA) and path-integral codes PATHINT/PATHTREE (and their quantum generalizations qPATHINT/qPATHTREE) are offered to detail such systems. Method: ASA and PATHINT/PATHTREE have been effective to forecast properties in three disparate disciplines in neuroscience, financial markets, and combat analysis. Applications are described for COVID-19. Results: Results of detailed calculations have led to new results and insights not previously obtained. Conclusion: These 3 applications give strong support to a quite generic application of these tools to stochastic nonlinear systems.

The relentless advancement and integration of mechanization and intelligence within the coal mining industry, combined with the increasing depths of mining operations, necessitate significantly higher safety standards. This necessity arises due to the increasingly complex geological and coal seam conditions encountered as mining operations delve deeper into the earth. Traditionally, 3D seismic exploration technology has been fundamental in ensuring both operational efficiency and safety in the coal mining sector. However, despite its critical role, this technology still has limitations in detecting and characterizing small-scale geological structures which can pose substantial risks if not accurately identified and mitigated. To address these challenges, this paper introduces a sparsity-constrained adaptive hard thresholding algorithm designed to tackle the spectral inversion optimization problem with an norm constraint for the enhanced retrieval of reflection coefficients, thereby establishing a comprehensive workflow for enhancing seismic data resolution through compressed sensing spectral inversion. Real data validation has demonstrated that this method significantly enhances the resolution of seismic data while maintaining the amplitude integrity and fidelity of the original signals. This improvement allows for a more detailed and accurate characterization of small-scale geological features, which are critical in identifying and mitigating potential hazards within coal mining operations, thus offering robust support for the implementation of more effective safety protocols and disaster prevention strategies in coal mines.

In the context of video background-foreground separation, we propose a compressive online Robust Principal Component Analysis (RPCA) with optical flow that separates recursively a sequence of video frames into foreground (sparse) and background (low-rank) components. This separation method can process per video frame from a small set of measurements, in contrast to conventional batch-based RPCA, which processes the full data. The proposed method also leverages multiple prior information by incorporating previously separated background and foreground frames in an n-l₁ minimization problem. Moreover, optical flow is utilized to estimate motions between the previous foreground frames and then compensate the motions to achieve higher quality prior foregrounds for improving the separation. Our method is tested on several video sequences in different scenarios for online background-foreground separation given compressive measurements. The visual and quantitative results show that the proposed method outperforms other existing methods.

This paper proposes the use of compressive sensing to tackle the Massive MIMO channel estimation problem. As our results show compressive sensing-based estimators perform as well as the optimum MMSE estimator.

With the development of hyperspectral technology, to establish an effective spectral data compressive reconstruction method that can improving data storage, transmission and maintaining spectral information is critical for quantitative remote sensing research and application in vegetation. By introducing the idea of compressive sensing in compressed reconstruction, the spectral adaptive grouping distributed compressive sensing algorithm is proposed, which enables a distributed compressed sensing reconstruction of plant hyperspectral data. The experimental results showed that comparing with orthogonal matching pursuit(OMP) and gradient projection reconstruction(GPSR), the proposed algorithm can significantly improve the visual effect of image reconstruction in the spatial domain. The PSNR in low sampling rate(sampling rate is lower than 0.2) increases by 13.72dB than OMP and 1.66dB than GPSR. In the spectral domain, the average normalized root mean square error、the mean absolute percentage error and the mean absolute error of the proposed algorithm is35.38%，31.83% and 33.33% lower than GPSR respectively.. Therefore, the proposed algorithm can achieve relatively high reconstructed efficiency.

(1) Background: This study aimed to evaluate whether the implementation of a modified blood sampling protocol, which focused on need-based laboratory testing and minimized venous sampling by replacing it with point-of-care testing (POCT) via capillary puncture, successfully reduced iatrogenic blood loss, incidence of anemia, and frequency of blood transfusion in extremely low birth weight infants (ELBWIs) without negatively affecting neonatal outcomes. (2) Methods: A retrospective analysis was conducted on 313 ELBWIs of gestational age (GA) between 23 and 28 weeks, born between 2013 and 2019. The infants were divided into two groups: before (period I) and after (period II) the implementation of the modified blood sampling protocol in January 2016. Propensity score matching was conducted to minimize selection bias. Clinical data, including the frequency and amount of blood sampling, frequency and volume of blood transfusion, and clinical characteristics, such as gestational age, birth weight, and neonatal outcome data, were collected and compared between the two groups. (3) Results: No significant differences in the GA or birth weight between the two periods were observed. The total sampling volume during a month after birth (16.7 ± 4.1 mL vs. 15.6 ± 4.4 mL, P=0.03) and total sampling volume during hospital days (51.4 ± 29.7 mL vs. 44.3 ± 27.5 mL, P=0.04) in period II were significantly lower than that in period I. There were no differences in the mortality or morbidity between the two periods. Although the transfusion frequency and amount did not have significant differences between the periods, we observed a positive correlation between the transfusion frequency and sampling volume (coefficient: 0.09, 95% CI: 0.08–0.11). (4) Conclusions: The modified blood sampling protocol effectively reduced the iatrogenic blood loss without negatively affecting the neonatal outcomes.

Rabies remains a significant global threat, yet accurate estimations of its impact are hindered by the lack of confirmatory diagnoses. Postmortem confirmation of rabies traditionally involves invasive brain tissue testing, a process met with resistance from deceased patients' families, impeding consent. This paper presents and evaluates an innovative yet unpublished transnasal approach for postmortem brain tissue collection, offering a minimally invasive, easier, faster, and safer method. This method preserves the cadaver's integrity, potentially easing family reluctance towards autopsies. The limited testing of both human and animal rabies in Ghana highlights the challenges in diagnosing this fatal disease. Scarce diagnostic resources and the complexity of obtaining brain tissue samples exacerbate the issue. Cultural and religious beliefs surrounding autopsies contribute to familial hesitation, viewing these procedures as disruptive and disfiguring, further complicating consent. The transnasal technique involves approaching the brain tissue through the nostrils and cribriform plate without any superficial manipulation of the patient's head and face, thereby preserving aesthetics and natural features of the person. Technological advancements and seamless One Health collaboration among governmental, non-governmental, and research entities locally and globally culminated in Ghana's first confirmed rabies diagnosis using this method of brain tissue collection. This success emphasizes the efficiency and feasibility of transnasal brain collection approach and the invaluable role of the One Health approach and collaborative efforts in overcoming diagnostic challenges in rabies control.

Ranked Set Sampling (RSS) is a useful technique for improving the estimator of population mean when the sampling units in a study can be easily ranked than the actual measurement. RSS performs better than simple random sampling (SRS) when the mean of units corresponding to each rank is used. The performance of RSS can be increased further by assigning weights to the ranked observations. In this paper, we propose weighted RSS procedures to estimate the population mean of positively skew distributions. It is shown that the gain in the relative precisions of the population mean for chosen distributions are uniformly higher than those based on RSS. The gains in relative precisions are substantially high. Further, the relative precisions of our estimator are slightly higher than the ones based on Neyman’s optimal allocation model for small sample sizes. Moreover, it is shown that, the performance of the proposed estimator increases as the skewness increases by using the example of lognormal family of distributions.

There is growing interest in characterizing the viromes of diverse mammalian species, particularly in the context of disease emergence. However, little is known about virome diversity in aquatic mammals, in part due to difficulties in sampling. We characterized the virome of the exhaled breath (or blow) of the Eastern Australian humpback whale (Megaptera novaeangliae). To achieve an unbiased survey of virome diversity a meta-transcriptomic analysis was performed on 19 pooled whale blow samples collected via a purpose-built Unmanned Aerial Vehicle (UAV, or drone) approximately 3km off the coast of Sydney, Australia during the 2017 winter annual northward migration from Antarctica to northern Australia. To our knowledge, this is the first time that UAVs have been used to sample viruses. Despite the relatively small number of animals surveyed in this initial study, we identified six novel virus species from five viral families. This work demonstrates the potential of UAVs in studies of virus disease, diversity, and evolution.

Microvascular self-healing composite materials have significant potential for application and their mechanical properties need in-depth investigation. In this paper, tensile and compressive properties of woven fabric carbon fiber reinforced polymers (CFRP) laminates containing three-dimensional microvascular channels were investigated experimentally. Several detailed finite element (FE) models were established to simulate the mechanical behavior of the laminate and the effectiveness of different models were examined. The damage propagation process of the microvascular laminates and the influence of microvascular parameters were studied by the validated models. The results show that microvascular channels arranged along the thickness direction (z-direction) of the laminates are critical locations under the loads. The channels have minimal effect on the stiffness of the laminates but causing a certain reduction in strength, which varies approximately linearly with the z-direction channel diameter within its common design range of 0.1~1mm. It is necessary to consider the resin-rich region formed around microvascular channels in the warp and weft fiber yarns of the woven fabric composite when establishing the FE model. And the layers in model should be assigned with equivalent unidirectional ply material in order to calculate the mechanical properties of laminates correctly.

Flue gas desulfurization gypsum (FGD gypsum) is obtained from the desulphurization of combustion gases in fossil fuel power plants. FGD gypsum can be used to produce anhydrite binder. The effect of three independent variables such as the calcination temperature of FGD gypsum (500-800 oC), the hydration time (3-28 days) and the amount of activator (0-2 %) on the compressive strength of anhydrite binder were studied. K2SO4 and Na2SO4 were used as activators. The compressive strength of anhydrite binder was evaluated using a full factorial design. The multiple linear regression models were developed to correlate the significant variables to the compressive strength of anhydrite binder. The experimental results and statistical analysis showed that the hydration time had the biggest impact on the compressive strength of anhydrite binder using K2SO4 and Na2SO4. K2SO4 made a greater influence on the compressive strength than Na2SO4. The results of modeling indicated that the individual variables had a larger effect on the compressive strength of anhydrite binder than their interaction. The mean absolute percentage error between experimental and calculated values of compressive strength was less than 10 %.

In remote sensing applications, one of the key points is the acquisition, real-time pre-processing and storage of information. Due to the large amount of information present in the form of images or videos, compression of this data is necessary. Compressed sensing (CS) is an efficient technique to meet this challenge. It consists in acquiring a signal, assuming that it can have a sparse representation, using a minimal number of non-adaptive linear measurements. After this CS process, a reconstruction of the original signal must be performed at the receiver. Reconstruction techniques are often unable to preserve the texture of the image and tend to smooth out its details. To overcome this problem, we propose in this work, a CS reconstruction method that combines the total variation regularization and the non-local self-similarity constraint. The optimization of this method is performed by the augmented Lagrangian which avoids the difficult problem of non-linearity and non-differentiability of the regularization terms. The proposed algorithm, called denoising compressed sensing by regularizations terms (DCSR), will not only perform image reconstruction but also denoising. To evaluate the performance of the proposed algorithm, we compare its performance with state-of-the-art methods, such as Nesterov's algorithm, group-based sparse representation and wavelet-based methods, in terms of denoising, and preservation of edges, texture and image details, as well as from the point of view of computational complexity. Our approach allows to gain up to 25% in terms of denoising efficiency, and visual quality using two metrics: PSNR and SSIM.

In vivo, articular cartilage tissue is surrounded by a cartilage membrane, and HP (HP) and compressive strain increases simultaneously with the compressive stress. However, it has been impossible to investigate the effects of simultaneous loading in vitro. In this study, a bioreactor capable of applying compressive stress under HP was developed to reproduce ex vivo the same physical loading environment found in cartilage in vivo. First, a HP stimulation unit was constructed to apply cyclic HP pressure-resistant chamber by controlling a pump and valve. A compression-loading mechanism that can apply compressive stress using an electromagnetic force was implemented in the chamber. The synchronization between the compression and HP units were evaluated and the stimulation parameters were quantitatively evaluated. Physiological HP and compressive strain were applied to the chondrocytes encapsulated in alginate and gelatin gels after applying high HP at 25 MPa, which induced damage to chondrocytes. It was found that compressive stimulation increased the expression of genes related to osteoarthritis. Furthermore, the simultaneous application of compressive strain and HP, which is similar to the physiological environment in cartilage, had an inhibitory effect on the expression of genes related to osteoarthritis. HP alone also suppressed the expression of osteoarthritis-related genes. Therefore, the simultaneous hydrostatic and compressive stress-loading device developed to simulate the mechanical environment in vivo may be an important tool for elucidating the mechanisms of disease onset and homeostasis in the cartilage.

(1) Background: The study aimed to investigate compressive strength for three computer-aided design/computer-aided manufacturing (CAD/CAM) dental materials: glassceramic IPS Empress CAD (IvoclarVivadent), hybrid ceramic Cerasmart (GC) and polymer-reinforced graphene G-CAM (Graphenano Dental). (2) Methods: 45 samples consisted of the molar crowns fabricated by three CAD/CAM materials were cemented adhesively on 3D printed abutments (Asiga DentalResin). The samples were divided into 3 groups (n=15) according to the crowns thickness; group 1 under the cusps/cervical margins - 0.6 mm/0.4 mm, group 2 - 1 mm/0.7 mm respectively, and group 3 - 1.5 mm/1 mm. Additionally, 20 cylindrical specimens fabricated by the three crowns and abutments material (n=5) were prepared by CAD/CAM technique. All samples and specimens were subjected to an axial compressive load by using a universal testing machine (Instron 3366-10kN, USA) until fracture. (3) Results: The compressive strength were for Empress CAD 1258 MPa, Cerasmart 501.3 MPa, G-CAM 435 MPa and Asiga resin 360 MPa. G-CAM crowns exhibited a higher maximum compressive load (1701.5-2011.8N) than both Cerasmart (1295.4-1642.9N) and Empress CAD (494.3-597.5N). (4) Conclusions: The CAD/CAM crown materials presented different mechanical behavior; Empress CAD and Cerasmart presented a fragile behavior, with a high compressive strength when compared to G-CAM and Asiga resins.

Influence of particle size on the mechanical strength of alkali activated material from waste refractory monolithic was investigated in this study. Precursor was chemically and mineralogically analysed, separated on 4 fractions and alkali activated with Na-water glass. Alkali activated materials were thoroughly investigated under SEM and XRD to evaluate the not predicted differences in mechanical strength. Time dependence of curing temperature on mechanical strength was investigated in the sample prepared from a fraction that caused the highest compressive strength.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

The present paper reports an alternative solution of the measurement problem in quantum theory. The measurement problem can be characterized as that the U-procedure verses the R-procedure. The R-procedure is tested by the Yes/No measurement originally proposed by von Neuman and discussed in details by Penrose. We propose a novel stochastic sampling method to tackle the measurement paradox. Each testing sample produces a pair of Yes-number c and No-number d, which in turn generates a sample phase with respect to the exponential form of (c+id). All the sample phases forms a group G_R. Taking G_R as the sampling potential, combined with the dynamic phase group G_U，we establish a unified model of U-procedure and R-procedure for the evolution of wavefunction. Based on the Born rule, the probability of a sample is given by the squared magnitude of （c+id）. Some metaproperties of the new U-R model, such as natural transformation, consistency, and completeness, are presented. The present work provides a new picture of quantum mechanics and alike. The measurement problem widely exists in dynamic analysis, higher cognition, and large data modeling. Thus, the work reported here has a wide range of applications. Keywords: The measurement problem; U-R procedures; the Yes/No type measurement; stochastic sampling; sample phase; Born probability.

Natural image matting is an essential technique for image processing that enables various applications, such as image synthesis, video editing, and target tracking. However, the existing image matting methods may fail to produce satisfactory results when computing resources are limited. Sampling-based methods can reduce the dimensionality of the decision space and therefore reduce computational resources by employing different sampling strategies. While these approaches reduce computational consumption, they may miss an optimal pixel pair when the number of available high-quality pixel pairs is limited. To address this shortcoming, we propose a novel multi-criterion sampling strategy that avoids missing high-quality pixel pairs by incorporating multi-range pixel pair sampling and high-quality samples selection method. This strategy is employed to develop a multi-criterion matting algorithm via Gaussian process, which searches for the optimal pixel pair by using the Gaussian process fitting model instead of solving the original pixel pair objective function. Experimental results demonstrate that our proposed algorithm outperforms other methods even with 1% computing resources, and achieves alpha matte results comparable to those yielded by the state-of-the-art optimization algorithms.

Human papillomavirus (HPV) self-sampling (Self-HPV) is a promising strategy to improve cervical cancer screening coverage in low-income countries. However, issues associated with women who prefer conventional HPV clinical-sampling over HPV self-sampling may affect screening participation. To address this issue, our study assessed factors associated with women’s preferences related to Self-HPV. This study was embedded in a large clinical trial recruiting women aged 30–49 years in a primary HPV-based study termed “3T-Approach” (for Test-Triage-Treatment), launched in 2018 at Dschang District Hospital, West Cameroon. Participants were invited to perform a Self-HPV. After the sampling and before receiving the results, participants completed a questionnaire about cervical cancer screening and their preferences and perceptions around Self-HPV. The median age of the 2201 participants was 40.6 (IQR 35–45) years. Most (1693 (76.9%)) preferred HPV self-sampling or had no preference for either method and 508 (23.1%) preferred clinician-sampling. Factors associated with an increased likelihood of reporting a clinician-sampling preference were tertiary educational level (14.4% CI: 12.8–16.1 vs 29.5% CI: 25.6–33.6) and being an employee with higher grade professional or managerial occupations (5.5% CI: 3.8–7.9 vs 2.6% CI: 2.3–2.8). The main reported reason for women preferring clinician-sampling was a lack of “self-expertise”. Most women (>99%) would agree to repeat HPV self-sampling and would recommend it to their relatives. HPV self-sampling in the cultural context of central Africa was well accepted by participants, but some participants would prefer to undergo clinician sampling. Health systems should support well-educated women to increase self-confidence in using HPV self-sampling.

This study is focused on the experimental investigation of compressive strength and durability properties of lightweight concrete mixtures with fine expanded glass and expanded clay aggregates using different microfillers. The paper proposes the relationships between the compressive strength and density of concrete mixtures with different proportions of lightweight aggregates mentioned above. The performed experimental studies have revealed the tendencies of possible usage of different amount of fine lightweight aggregates and their combinations in the production of concrete mixtures depending on the demands of practical application. Following the requirements for structural concrete subjected to environmental effects, durability properties (alkaline corrosion and freeze–thaw resistance) of the selected concrete mixtures with expanded glass aggregate were studied. The results of the experimental investigations have shown that durability of tested concrete specimens was sufficient. The study has concluded that the mixtures under consideration can be applied for the production of structural elements to which durability requirements are significant.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

From an industrial point of view, the milling of 2.5D cavities is a frequent operation, 1 consuming time and presenting optimization potential, especially through a judicious choice of 2 the tool trajectory. Among the different types of trajectories, some have a general spiral-like aspect 3 and can potentially offer a reduced machining time. They are called curvilinear trajectories and are 4 obtained by interpolation between structure curves which are the numerical solutions of a partial 5 differential equation. In this case, the machine tool will connect points and the trajectory will be made 6 up of small segments. Even if, macroscopically, these trajectories have all the qualities to allow the 7 tool to move quickly, on a small scale, the discontinuities in tangency, inherent in the discretization, 8 significantly increase machining time. This article suggests to enhancing the continuity level of the 9 toolpath by rebuilding structure curves with a set of Hermite quartic spline patches connected in 10 tangency and curvature. Thanks to this, the tool will machine at an average feedrate closer to the 11 programmed one and will, de facto, reduce traveling time. 12 This article shows that the proposed method increases, on the two tested cavities, toolpath quality 13 indicators, reduces milling time from 10% to 18% for a curvilinear method without a filter and make 14 it possible to generalize the Bieterman and Sandström method for all non convex pockets.

This research aims to study the ultimate limit state (ULS) behaviour of stiffened panel under longitudinal compression by non-linear finite element method (NLFEM). There are different types of stiffeners being used in shipbuilding i.e. T-bar, flat-bar and angle-bar. However, this research focuses on the ultimate compressive strength behaviour of flat-bar stiffened panel. A total of 420 of reliable scenarios of flat-bar stiffened panel are selected for numerical simulation by ANSYS NLFEM. The ultimate strength behaviours obtained were used as data for the development of closed form shape empirical formulation. Recently, Kim et al. [1] proposed for advanced empirical formulation for T-bar stiffened panel and the applicability of the proposed formulation to flat-bar stiffened panel will be confirmed by this study. The accuracy of the empirical formulation obtained for flat-bar stiffened panel has been validated by FE simulation results of statistical analysis (R2 = 0.9435). The outcome obtained will be useful for ship structural designers in predicting the ultimate strength performance of flat-bar type stiffened panel under longitudinal compression.

Osteoarthritis (OA) is a common joint disorder found mostly in elderly people. The role of mechanical behavior in the progression of OA is complex and remains unclear. The stress-relaxation behavior of human articular cartilage in clinically defined osteoarthritic stages may have importance in diagnosis and prognosis of OA. In this study we investigated differences in the biomechanical responses among human cartilage of ICRS grades I, II and III using polymer dynamics theory. We collected 24 explants of human articular cartilage (eight each of ICRS grade I, II and III) and acquired stress-relaxation data applying a continuous load on the articular surface of each cartilage explant for 1180 s. We observed a significant decrease in Young’s modulus, stress-relaxation time, and stretching exponent in advanced stages of OA (ICRS grade III). The stretch exponential model indicated that significant loss in hyaluronic acid polymer might be the reason for the loss of proteoglycan in advanced OA. This work encourages further biomechanical modelling of osteoarthritic cartilage utilizing these data as input parameters to enhance the fidelity of computational models aimed at revealing how mechanical behaviors play a role in pathogenesis of OA.

Aquatic macroinvertebrates play a crucial role in freshwater ecosystems, serving as reliable indicators of water quality and ecosystem health. To effectively monitor and assess these ecosystems, it is essential to employ appropriate sampling methods that capture the diversity and abundance of macroinvertebrate communities. The objective of this study was to provide a comprehensive overview and comparative analysis of different sampling methods for aquatic macroinvertebrates, highlighting their advantages, limitations, and applicability in ecological research was carried out. The results showed that the most commonly used methods include Kick-net Sampling, Surber Sampler, D-frame Net, Bottle Sampling, and Pitfall Traps. Researchers should select methods based on study goals, environmental conditions, and target organisms. Integrating multiple techniques enhances understanding of macroinvertebrate communities and their responses to environmental changes, contributing to improved assessments of water quality, ecosystem health, and conservation in freshwater ecosystems.

Micro-nano-plastics (MNPs) are an important constituent of atmospheric aerosol. However, there is still no standard procedure for their sampling and size fractionation, which is an obstacle to the aggregation and critical analysis of results obtained by different research groups. This review focuses on the sampling and fractionation methodologies used for MNPs. Moreover, a straightforward optimized methodology for the sampling and fractionation is proposed.

We advance binational link-tracing sampling design, an innovative data collection methodology for sampling from transnational social fields, i.e., transnational networks embedding migrants and non-migrants. This paper shows the practical challenges of such a design, the representativeness of the samples and the qualities of the resulted networks. We performed 303 face-to-face structured interviews on sociodemographic variables, migration trajectories and personal networks of people living in a Romanian migration sending community (Dâmbovița) and in a migration receiving Spanish town (Castellón), simultaneously in both sites. Inter-connecting the personal networks, we built a multi-layered complex network structure embedding 4,855 nominated people, 5,477 directed ties (nominations) and 2,540 edges. Results indicate that the participants’ unique identification is a particularly difficult challenge, the representativeness of the data is not optimal (homophily on observed attributes was detected in the nomination patterns), and the relational and attribute data allow to explore the social organization of the Romanian migrant enclave in Castellón, as well as its connectivity to other places. Furthermore, we provide methodological suggestions for improving link-tracing sampling from transnational networks of migration. Our research contributes to the emerging efforts of applying social network analysis to the study of international migration.

Malignant tumors behave dynamically as cell communities governed by ecological principles. Massive sequencing tools are unveiling the true dimension of the heterogeneity of these communities along their evolution in most human neoplasms, clear cell renal cell carcinomas (CCRCC) included. Although initially thought to be purely stochastic processes, very recent genomic analyses have shown that temporal tumor evolution in CCRCC may follow some deterministic pathways that give rise to different clones and sub-clones randomly spatially distributed across the tumor. This fact makes each case unique, unrepeatable and unpredictable. Precise and complete molecular information is crucial for patients with cancer since it may help in establishing a personalized therapy. Intratumor heterogeneity (ITH) detection relies on the correctness of tumor sampling and this is part of the pathologist’s daily work. International protocols for tumor sampling are insufficient today. They were conceived decades ago, when ITH was not an issue, and have remained unchanged until now. Noteworthy, an alternative and more efficient sampling method for detecting ITH has been developed recently. This new method, called multisite tumor sampling (MSTS), is specifically addressed to large tumors that are impossible to be totally sampled, and represent an opportunity to improve ITH detection without extra costs.

Dust storms play a crucial role in the climate system and the space environment of Mars and have a great impact on human’s Mars exploration activities. The Martian dust storms exhibit significant regional, seasonal and interannual variations due to various controlling factors such as the large-scale atmospheric circulation, varying solar radiation forcing, and Martial orbital and rotational motions and their coupling to the atmospheric dynamics. This paper focuses on the review of cur-rent understandings on Martian dust storms. This paper begins by elucidating the basic properties of dust storms, and their driving mechanisms and impacts on atmospheric dynamics, atmospheric electric property, space environment, topography, and Mars explorations. Then it introduces the observation methods on different platforms including orbiters and landers/rovers, and the da-tasets constructed based on these historical observations for Martian dust storms. Finally, we pro-posed the dust storm monitoring and forecasting for the upcoming Chinese Tianwen-3 Mars sam-pling returning mission. It concludes by depicting the future research topics to systematically un-derstand the Martian dust storms.

Malassezia is lipid-dependent commensal yeast of the human skin. The different culture media and skin sampling methods used to grow these fastidious yeasts are a source of heterogeneity in culture-based epidemiological study results. This study aimed to compare the performances of three methods of skin sampling, and two culture media for the detection of Malassezia yeasts by culture from the human skin. Three skin sampling methods, namely sterile gauze, dry swab and TranswabTM with transport medium, were applied on 10 healthy volunteers. Each sample was further inoculated onto either the novel FastFung medium or the reference Dixon agar for the detection of Malassezia spp. by culture. At least one colony of Malassezia spp. grew on 93/300 (31%) of the cultures, corresponding to 150 samplings. The positive culture rate was 67%, 18%, and 15% (P < 10-3), for samples collected with sterile gauze, TranswabTM, and dry swab, respectively. The positive culture rate was 62% and 38% (P < 0.003) by using the FastFung and the Dixon media, respectively. Our results showed that sterile gauze rubbing skin sampling followed by inoculation on FastFung medium should be implemented in the routine clinical laboratory procedure for Malassezia spp. cultivation.

Objective: In low- and middle-income countries (LMICs), household survey data are a main source of information for planning, evaluation, and decision-making. Standard surveys are based on censuses, however, for many LMICs it has been more than ten years since their last census and they face high urban growth rates. Over the last decade, survey designers have begun to use modelled gridded population estimates as sample frames. We summarize the state of the emerging field of gridded population survey sampling, focussing on LMICs. Methods: We performed a systematic review and identified 43 national and sub-national gridded population-based household surveys implemented across 29 LMICs. Findings: Gridded population surveys used automated and manual approaches to derive clusters from WorldPop and LandScan gridded population estimates. After sampling, many surveys interviewed all households in each cluster or segment, though some sampled households from larger clusters. Tools to select gridded population survey clusters include the GridSample R package, Geo-sampling tool, and GridSample.org. In the field, gridded population surveys generally relied on geographically accurate maps based on satellite imagery or OpenStreetMap, and a tablet or GPS technology for navigation. Conclusions: For gridded population survey sampling to be adopted more widely, several strategic questions need answering regarding cell-level accuracy and uncertainty of gridded population estimates, the methods used to group/split cells into sample frame units, design effects of new sample designs, and feasibility of tools and methods to implement surveys across diverse settings.

Nowadays a recognized need for accurate observations of atmospheric aerosols (AEs) and reactive gases (RGs) exists in the framework of regional, national and global near-surface networks based on permanent or mobile measurement stations. In this context, a paramount and not-trivial issue is related to the correct execution of continuous sampling of ambient air and its subsequent distribution to measurement analyzers hosted inside the stations. Sampling artifacts must be minimized for obtaining reliable pictures of ambient air composition. To respond to this need, a suite of novel “smart” and relatively low-cost systems for the continuous sampling of ambient air was developed in the framework of the Project I-AMICA (2012 – 2015, www.i-amica.eu). These systems were designed to execute AE and RG measurements according with WMO/GAW and ACTRIS recommendations and standard operation procedures. A particular attention was dedicated to the stabilization and control of the sampling flow rates and temperatures. The analysis of one full year of operations at the WMO/GAW regional station of Capo Granitola (GAW ID: CGR, Italy), allowed to conclude that these systems are effective in meeting the technical requirements for correct execution of AE and RG measurements

Non-destructive testing has many advantages, such as the ability to obtain a large number of data without destroying existing structures. However, the reliability of the estimation accuracy and the limited range of applicable targets remains an issue. This study proposes to a novel pin penetration test method to determine the early age compressive strength of concrete before demolding. The timing of demolding and initial curing are determined according to the strength development of concrete. Therefore, it is important to determine the compressive strength at the early age before demolding at the actual construction site. The applicability of this strength estimation methodology at actual construction is investigated. Small test holes (12 mm in diameter) are prepared on the mold surface in real construction sites and mock-up specimens in advance. The pin is penetrated into these test holes to obtain the relationship between the compressive strength and the penetration depth. As a result, it is confirmed that the pin penetration test method is suitable to measure the early age compressive strength at actual construction site. This allows the benchmark values for compressive strength, necessary to avoid early frost damage, to be directly verified on the concrete structural members at the construction site. For instance, the compressive strengths of greater than 5 MPa and 10 MPa can be confirmed by the penetration depths benchmark values of 8.0 mm and 6.7mm or less, respectively.

Bamboo is considered a sustainable construction material due to its ability to grow quickly and its mechanical properties that are comparable to timber. Contributing to the current effort to establish the structural bamboo standards in the National Structural Code of the Philippines (NSCP), this study establishes the characteristic compressive strength of four bamboo species: Bambusa vulgaris (36 samples), Dendrocalamus asper (36 samples), Bambusa blumeana (94 samples), and Guadua angustifolia Kunth (30 samples). The samples were subjected to compressive loading following ISO 22157-1 (2017). The characteristic compressive strength values obtained, according to ISO 12122-1 (2014), were 40.35 MPa for B. vulgaris, 40.21 MPa for D. asper, 46.63 MPa for B. blumeana, and 36.99 MPa for G. angustifolia Kunth. Simple linear analysis, One-way ANOVA, and Welch’s t-Test were used to analyze the correlation models and establish a comparative analysis of the effect of nodes, and geometric and physical properties on the compressive strength of bamboos. Comparing the characteristic compressive strength obtained from this study to the strength of unseasoned structural timber of Philippine woods, all bamboo species showed higher strength values, and thus have great potential as an alternative construction material to timber.

This work combines compressive sensing and short word-length techniques to achieve localization and target tracking in wireless sensor networks with energy-efficient communication between the network anchors and the fusion center. Gradient descent localization is performed using time-of-arrival (TOA) data which are indicative of the distance between anchors and the target thereby achieving range-based localization. The short word-length techniques considered are delta modulation and sigma-delta modulation. The energy efficiency is due to the reduction of the data volume transmitted from anchors to the fusion center by employing any of the two delta modulation variants with compressive sensing techniques. Delta modulation allows the transmission of one bit per TOA sample. The communication energy efficiency is increased by RⱮ, R≥1, where R is the sample reduction ratio of compressive sensing and Ɱ is the number of bits originally present in a TOA-sample word. It is found that the localization system involving sigma-delta modulation has a superior performance to that using delta-modulation or pure compressive sampling alone, in terms of both energy efficiency and localization error in the presence of TOA measurement noise, owing to the noise shaping property of sigma-delta modulation.

Recently concluded, large-scale cancer genomics studies involving multiregion sequencing of primary tumors and paired metastases appear to indicate that many or most cancer patients have one or more “clonal" mutations in their tumors. Clonal mutations are those that are present in all of a patient’s cancer cells. Achilles Therapeutics is currently the only company specifically targeting clonal mutations. However, they are doing so with tumor-derived T cells. To address the potential limitations of immunotherapy, I have devised another approach for exploiting clonal mutations, which I call “Oncolytic Vector Efficient Replication Contingent on Omnipresent Mutation Engagement” (OVERCOME). The ideal version of OVERCOME would likely employ a bioengineered facultative intracellular bacterium. The bacterium would initially be attenuated, but (transiently) reverse its attenuation upon clonal mutation detection.

To sample from complex, high-dimensional distributions, one may choose algorithms based on the Hybrid Monte Carlo (HMC) method. HMC-based algorithms generate nonlocal moves alleviating diffusive behavior. Here, I build on an already defined HMC framework, Hybrid Monte Carlo on Hilbert spaces [A. Beskos, F.J. Pinski, J.-M. Sanz-Serna and A.M. Stuart, Stoch. Proc. Applic. 121, 2201 - 2230 (2011); doi:10.1016/j.spa.2011.06.003] that provides finite-dimensional approximations of measures π which have density with respect to a Gaussian measure on an infinite-dimensional Hilbert (path) space. In all HMC algorithms, one has some freedom to choose the mass operator. The novel feature of the algorithm described in this article lies in the choice of this operator. This new choice defines a Markov Chain Monte Carlo (MCMC) method which is well defined on the Hilbert space itself. As before, the algorithm described herein uses an enlarged phase space Π having the target π as a marginal, together with a Hamiltonian flow that preserves Π. In the previous method, the phase space π was augmented with Brownian bridges. With the new choice for the mass operator, π is augmented with Ornstein-Uhlenbeck (OU) bridges. The covariance of Brownian bridges grows with its length, which has negative effects on the Metropolis-Hasting acceptance rate. This contrasts with the covariance of OU bridges which is independent of the path length. The ingredients of the new algorithm include the definition of the mass operator, the equations for the Hamiltonian flow, the (approximate) numerical integration of the evolution equations, and finally the Metropolis-Hastings acceptance rule. Taken together, these constitute a robust method for sampling the target distribution in an almost dimension-free manner. The behavior of this novel algorithm is demonstrated by computer experiments for a particle moving in two dimensions, between two free-energy basins separated by an entropic barrier.

In this paper the problem of sampling from uniform probability distributions is approached by means of space-filling curves (SFCs), a topological concept that has found a number of important applications in recent years. Departing from the theoretical fact that they are surjective but not necessarilly injective, the investigation focused upon the structure of the distributions obtained when their domain is swept in a uniform and discrete manner, and the corresponding values used to build histograms, that are approximations of their true PDFs. This work concentrates on the real interval [0,1], and the Sierpinski space-filling curve was chosen because of its favorable computational properties. In order to validate the results, the Kullback-Leibler distance is used when comparing the obtained distributions in several levels of granularity with other already established sampling methods. In truth, the generation of uniform random numbers is a deterministic simulation of randomness using numerical operations. In this fashion, sequences resulting from this sort of process are not truly random.

Abstract: In recent years, the construction engineering sector has undergone a transformative shift towards the integration of machine learning (ML) techniques, particularly in predicting the properties of steel fiber-reinforced concrete (SFRC). Despite the theoretical sophistication of existing models, a persistent challenge remains – their opacity, lacking transparency and real-world relevance for practi-tioners. To address this gap and advance our current understanding, this study employs the extra gradient (XG) Boosting algorithm, crafting a comprehensive ap-proach. Grounded in a meticulously curated database drawn from 43 seminal pub-lications, encompassing 420 distinct records, this research focuses predominantly on three primary fiber types: crimped, hooked, and mil-cut. Complemented by hands-on experimentation involving 20 diverse SFRC mixtures, this empirical campaign is further illuminated through the strategic use of Partial Dependence Plots (PDPs), revealing intricate relationships between input parameters and con-sequent compressive strength. A pivotal revelation of this research lies in the identification of optimal SFRC formulations, offering tangible insights for real-world applications. The developed ML model stands out not only for its sophistication but also its tangible accuracy, evidenced by exemplary performance against inde-pendent datasets, boasting a commendable mean target-prediction ratio of 99%. To bridge the theory-practice gap, we introduce a user-friendly digital interface, thri-ughly designed to guide professionals in optimizing and accurately predicting the compressive strength of SFRC. This research thus contributes to the construction and civil engineering sectors by enhancing predictive capabilities and refining mix designs, fostering innovation, and addressing the evolving needs of the industry.

This paper discusses the tectonics of the St. Peter and St. Paul Archipelago (SPSPA) in the Equato-rial Atlantic Ocean, based on the joint-system geometry which show a North-South shorten-ing/transpressional uplift tectonism, is active leading to exhumation of the sub-oceanic mantle. These islets are the summits of a sigmoidal submarine ridge formed by mantle ultramafic rocks. The ridge is crossed by the principal transform deformation zone of the northern transform fault of the St. Paul Multifault System. The South flank ridge exposes serpentinized mantle perido-tites, while the North flank exposes strongly deformed/fractured ultramylonites, recording duc-tile and brittle deformation at lithospheric conditions. The SPSPA show multiple joint systems cutting mylonitic foliation of the exposed rocks, forming three main families: high-angle paral-lel joints of tectonic origin, serpentinization-related joints with random direction and load-release low-angle parallel joints. The tectonic joints show an average direction of N31°E and N28°W, forming a conjugate system with a N1ºW compression axes, coherent with a trans-pressive stress field. Accordingly, the earthquakes focal mechanism close to the islets also shows N-S compression. The previously reported active uplift with an average rate of 1.5 mm/year and the directions of the joint system here reported agreeing with a present-day active N-S compres-sive field at a high angle with the direction of the transform fault.

This study aims to model grinding of a Polish slag and evaluate the particle size distributions of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e. temperature, curing and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin-Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multi fractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

Volatile compounds, abundant in breath, can be used to accurately diagnose and monitor a range of medical conditions. This offers a non-invasive, low-cost approach with screening applications; however, uptake of this diagnostic approach has been limited by conflicting published outcomes. Most published reports rely on large scale screening of the public, at single time points and without reference to ambient air. Here, we present a novel approach to volatile sampling from cellular headspace and mouse breath that incorporates multi-time point analysis and ambient air subtraction revealing compound flux as an effective proxy of active metabolism. This approach to investigating breath volatiles offers a new avenue for disease biomarker discovery and diagnosis. Using gas chromatography mass spectrometry (GC/MS), we focus on low molecular weight, metabolic substrate/by-product compounds and demonstrate that this non-invasive technique is sensitive (reproducible at ~1 µg cellular protein, or ~500,000 cells) and capable of precisely determining cell type, status and treatment. Isolated cellular models represent components of larger mammalian systems and we show that stress- and pathology-indicative compounds are detectable in mice, supporting further investigation using this methodology as a tool to identify volatile targets in human patients.

The modifications in planting structure and continuous land use adjustments have significant implications for the structure, diversity, and functioning of arthropod communities in farmland landscapes, particularly regarding the biological control of pest insects by natural enemy species. Therefore, there is an urgent need to comprehensively and accurately assess insect community diversity in croplands. In this study conducted between 2022-2023, we utilized Malaise traps and sweep netting to collect insects from three different double-cropping paddy fields. We extracted DNA from preservative ethanol of Malaise traps and tissue samples of selected parasitoid wasps, followed by amplification using DNA barcoding primers to prepare high-throughput sequencing libraries. As a result, we annotated a total of 4956 operational taxonomic units (OTUs) belonging to 174 genera and 32 families of parasitoid wasps. Our findings demonstrate that the ethanol filter method efficiently captures a wide range of information diversity. However, it demonstrates a lower resolution and may result in a reduction of species abundance. Furthermore, we have identified additional insect species in the parasitoid samples. This demonstrates that high throughput sequencing from adult parasitoid wasps can effectively detect host specie, enabling a comprehensive understanding of host species and providing novel insights into food web construction.

The analysis of microscopy images has always been an important yet time consuming process in in materials science. Convolutional Neural Networks (CNNs) have been very successfully used for a number of tasks, such as image segmentation. However, training a CNN requires a large amount of hand annotated data, which can be a problem for material science data. We present a procedure to generate synthetic data based on ad-hoc parametric data modelling for enhancing generalization of trained neural network models. Especially for situations where it is not possible to gather a lot of data, such an approach is beneficial and may enable to train a neural network reasonably. Furthermore, we show that targeted data generation by adaptively sampling the parameter space of the generative models gives superior results compared to generating random data points.

Welding of dissimilar aluminium alloys has been a challenge for a long period until the discovery of the solid state welding technique called friction stir welding (FSW). The discovery of this technique encouraged different research interests revolving around the optimization of this technique. This involves the welding parameters optimization and this optimization is categorized into two classes i.e. similar alloys and dissimilar alloys. This paper reports about the mechanical properties of the friction stir welded dissimilar AA1050-H14 and AA5083-H111 joint. The main focus is to compare the mechanical properties of specimens extracted from different locations of the welds i.e. the beginning, middle and the end of the weld. The specimen extracted at the beginning of the weld showed low tensile properties compared to specimens extracted from different locations of the weld. There was no certain trend noted through the bending results. All three specimens showed dimpled fracture which is the characterization of the ductile fracture.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

Artificial intelligence is increasingly used in various branches of engineering. In this article, artificial neural networks are used to predict the crush resistance of corrugated packaging. Among the analysed packages were boxes with ventilation openings, packages with perforations, and typical flap boxes, which makes the proposed estimation method very universal. Typical shallow feedforward networks were used, which are perfect for regression problems, mainly when the set of input and output parameters is small, so no complicated architecture or advanced learning techniques are required. The input parameters of the neural networks are selected so as to take into account not only the material used for the production of the packaging, but also the dimensions of the box and the impact of ventilation holes and perforations on the load capacity of individual walls of the packaging. In order to maximize the effectiveness of neural network training process, the group of input parameters was changed so as to eliminate those to which the sensitivity of the model was the lowest. This allowed the selection of the optimal configuration of training pairs for which the estimation error was on the acceptable level. Finally, models of neural networks were selected, for which the training and testing error did not exceed 10%. The demonstrated effectiveness allows to conclude that the proposed set of universal input parameters is suitable for efficient training of a single neural network model capable of predicting the compressive strength of various types of corrugated packaging.

In the modern world, all manufacturers strive for the optimal design of their products. This general trend is recently also observed in the corrugated board packaging industry. Colorful prints on displays, perforations in shelf-ready-packaging and various types of ventilation holes in trays, although extremely important for ergonomic or functional reasons, weaken the strength of the box. To meet the requirements of customers and recipients, packaging manufacturers outdo each other in new ideas for the construction of their products. Often the aesthetic qualities of the product become more important than the attention to maintaining the standards of the load capacity of the packaging (which, apart from their attention-grabbing functions, are also intended to protect transported products). The particular flaps design (both top and bottom) and their influence on the strength of the box is investigated in this study. The updated analytical-numerical approach is used here to predict the strength of the packaging with various flap’s offsets. Experimental results indicated a significant decrease in the static load-bearing capacity of packaging in the case of shifted flap creases. The simulation model proposed in our previous work has been modified and updated to take into account also this effect. The results obtained by the model presented in the paper are in satisfactory agreement with the experimental data.

Recently, the focus of entity linking research has centered on the zero-shot scenario, where the entity mention to be labeled at the time of testing was never observed during the training phase or may belong to a different domain than the source domain. Current studies have used BERT as the base encoder as it effectively establishes distributional links between source and target domains. The currently available negative sampling methods all use an extractive approach, which makes it difficult for the models to learn diverse and more challenging negative samples. To address this problem, we propose a generative negative sampling method, Adaptive_mixup_hard, which generates more difficult negative entities by fusing the features of both positive and negative samples on top of hard negative sampling and introduces a transformable adaptive parameter W to increase the diversity of negative samples. Next, we fuse our method with the Biencoder architecture and evaluate its performance under three different score functions. Ultimately, experimental results on the standard benchmark dataset Zeshel demonstrate the effectiveness of our method.

This work addresses the problem of sampling from Gaussian probability distributions by means of uniform samples obtained deterministically and directly from space-filling curves (SFCs), a purely topological concept. To that end, the well-known inverse cumulative distribution function method is used, with the help of the probit function,which is the inverse of the cumulative distribution function of the standard normal distribution. Mainly due to the central limit theorem, the Gaussian distribution plays a fundamental role in probability theory and related areas, and that is why it has been chosen to be studied in the present paper. Numerical distributions (histograms) obtained with the proposed method, and in several levels of granularity, are compared to the theoretical normal PDF, along with other already established sampling methods, all using the cited probit function. Final results are validated with the Kullback-Leibler and two other divergence measures, and it will be possible to draw conclusions about the adequacy of the presented paradigm. As is amply known, the generation of uniform random numbers is a deterministic simulation of randomness using numerical operations. That said, sequences resulting from this kind of procedure are not truly random. Even so, and to be coherent with the literature, the expression ”random number” will be used along the text to mean ”pseudo-random number”.

Electronic-health applications rely on large computer networks to facilitate patients' information access and to communicate various types of medical data. To examine the effectiveness of these networks, the traffic parameters need to be analysed. Due to quantity of the information carrying packets, examining each packet's transmission parameters individually is not practical, especially when a real time operation is needed. Sampling allows a subset of packets that accurately represents the original traffic to be formed. In this study an adaptive sampling method based on regression and fuzzy inference system was developed. It dynamically updates the number of packets sampled by responding to the traffic variations. Its performance was found to be superior to the conventional non-adaptive sampling methods.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

Due to advances in power electronics technology and the evolution of automation devices, the number of electrical devices that are sensitive to power quality is rapidly increasing, and for this reason, users are increasing their demand for high quality. To meet power quality demands, many power conversion devices are used, including dynamic voltage restorers (DVRs). DVRs are rec-ognized as devices that can effectively manage problems such as voltage segment, swells, and harmonics. DVR control requires many samples for harmonic compensation, which has the dis-advantage of being complicated to implement due to fast digital signal processing computation and the application of the cyclic discrete Fourier transform. In this paper, a high-precision DVR system configuration is proposed that compensates for harmonics using a periodically equivalent time-interval sampling technique and a novel circular structured memory filter. The proposed circular structured multi-pointer memory filter is an effective filter algorithm for high-precision input voltage measurement because it can remove noise and compensate for the delay of the phase angle of the filter in voltage measurement. A simulation and DVR prototype system was built, and the feasibility and effectiveness of the phase angle multi-filter voltage detection method and the compensation method were verified by experiments.

Glioblastoma, a deadly brain tumor, shows limited response to standard therapies like te-mozolomide (TMZ). Recent findings from the REGOMA trial underscore a significant survival improvement offered by regorafenib (REGO) in recurrent glioblastoma. Our study aimed to propose a 3D ex vivo drug response precision medicine approach to investigate recurrent glio-blastoma sensitivity to REGO and elucidate the underlying molecular mechanisms involved in tumor resistance or responsiveness to treatment. 3D glioblastoma organoids (GB-EXPs) obtained from 18 patients’ resected recurrent glioblastoma tumors were treated with TMZ and REGO. Drug responses were evaluated using NAD(P)H FLIM, stratifying tumors as responders (Resp) or non-responders (NR). Whole-exome sequencing was performed on 16 tissue samples, and whole-transcriptome analysis on 13 GB-EXPs treated and untreated. We found 35% (n=9) and 77% (n=20) of tumors responded to TMZ and REGO, respectively, with no instances of TMZ-Resp be-ing REGO-NR. Exome analysis revealed a unique mutational profile in REGO-Resp tumors compared to NR tumors. Transcriptome analysis identified distinct expression patterns in Resp and NR tumors, impacting Rho GTPase and NOTCH signaling, known to be involved in drug response. In conclusion, recurrent glioblastoma tumors were more responsive to REGO com-pared to TMZ treatment. Importantly, our approach enables a comprehensive longitudinal ex-ploration of the molecular changes induced by treatment, unveiling promising biomarkers in-dicative of drug response.

Fungal infection of grape berries (Vitis vinifera) by Botrytis cinerea frequently coincides with harvest, impacting both the yield and quality of grape and wine products. A rapid and non-destructive method for identifying B. cinerea infection in grapes at an early stage prior to harvest is critical to manage loss. In this study, zeolitic imidazolate framework-8 (ZIF-8) crystal was applied as an absorbent material for volatile extraction from B. cinerea-infected and healthy grapes in a vineyard followed by thermal desorption gas chromatography-mass spectrometry. The performance of ZIF-8 to absorb and trap targeted volatiles was evaluated with a standard solution of compounds and with a whole bunch of grapes enclosed in a glass container to maintain standard sampling conditions. Results from sampling methods were then correlated to B. cinerea infection in grapes as measured and determined by Genus specific antigen quantification. Trace levels of targeted compounds reported as markers of grape B. cinerea infection were successfully detected with in-field sampling. Peak area counts for volatiles 3-octanone, 1-octen-3-one, 3-octanol, and 1-octen-3-ol extracted using ZIF-8 were significantly higher than values achieved using Tenax®-TA from field testing and demonstrated good correlation with B. cinerea infection severities determined by B. cinerea antigen detection.

Validation of satellite sea surface salinity (SSS) products is typically based on comparisons with in-situ measurements at a few meters depth, that are mostly done at a single location and time. The difference in term of spatio-temporal resolution between the in-situ near-surface salinity and the two-dimensional satellite SSS results in a sampling mismatch uncertainty. The Climate Change Initiative (CCI) project has merged SSS from three satellite missions. Using an optimal interpolation, weekly and monthly SSS and their uncertainties are estimated at a 50 km spatial resolution over the global ocean. Over the 2016-2018 period the mean uncertainty on weekly CCI SSS is 0.13, whereas the standard deviation of weekly CCI minus in-situ Argo salinities is 0.24. Using high resolution SSS simulations, we estimate the expected uncertainty due to the CCI versus Argo sampling mismatch. Most of the largest spatial variability of the satellite minus Argo salinity are observed in regions with large mismatch. A quantitative validation is performed by considering the statistical distribution of the CCI minus Argo salinity normalized by the sampling and retrieval uncertainties. This quantity should follow a Gaussian distribution with a standard deviation of 1, if all uncertainty contributions are properly considered. We find that 1) the sampling mismatch can explain most of the observed differences between Argo and CCI data, especially for monthly products and in dynamical regions (river plumes, fronts), 2) overall, the uncertainties are well estimated in CCI version 3, much better compared to CCI version 2. There are a few dynamical regions where discrepancies remain, and where the satellite SSS, their associated uncertainties and the sampling mismatch estimates should be further validated.

In most industrialized countries, screening programs for cervical cancer have shifted from cytology (Pap smear or ThinPrep) alone on clinician-obtained samples to the addition of screening for human papillomavirus (HPV), its main causative agent. For HPV testing, self-sampling instead of clinician-sampling has proven to be equally accurate, in particular for assays that use nucleic acid amplification techniques. In addition, HPV testing of self-collected samples in combination with a follow-up Pap smear in case of a positive result is more effective in detecting precancerous lesions than a Pap smear alone. Self-sampling for HPV testing has already been adopted by some countries, while others have started trials to evaluate its incorporation into national cervical cancer screening programs. Self-sampling may result in more individuals willing to participate in cervical cancer screening, because it removes many of the barriers that prevent women, especially those in low socioeconomic and minority populations, from participating in regular screening programs. Several studies have shown that the majority of women who have been underscreened but who tested HPV-positive in a self-obtained sample, will visit a clinic for follow-up diagnosis and management. Additionally, a self-collected sample can also be used for vaginal microbiome analysis, which can provide additional information about HPV infection persistence as well as vaginal health in general.

Abstract: To overcome the environmental impact of cement production in cocnrete , the construction industry is adopting eco-friendly approaches, such as incorporating alternative and recycled materials, minimizing carbon emissions in concrete production. One such material that has gained prominence is Ground Granulated Blast Furnace Slag (GGBFS),. This study focuses on investigating the compressive strength of concrete at 28 days of age by examining the influences of several factors, such as temperature, water-to-binder ratio (w/b), GGBFS-to-binder ratio (GGBFS/b), fine aggregate, coarse aggregate, and superplasticizer. A statistical modeling approach was employed to comprehensively analyze these parameters and assess their impact on the compressive strength. To accomplish this, the study collected and analyzed data from the literature, resulting in a dataset of 210 observations. The dataset was divided into training and testing groups, and statistical analyses were performed to assess the relationships between the input parameters and compressive strength. The correlation analysis revealed insignificant relationships between the input parameters and compressive strength, indicating that multiple factors affect the strength. Different models, such as linear regression, nonlinear regression, quadratic, full quadratic models, and artificial neural networks (ANN) were employed to predict the compressive strength. The findings of this study contribute to a better understanding of the factors that influence the compressive strength of concrete containing GGBFS. The results underscore the importance of considering multiple parameters to predict strength accurately.

Purpose To alleviate the data imbalance problem caused by subjective and objective reasons, scholars have developed different data preprocessing algorithms, among which undersampling algorithms are widely used because of their fast and efficient performance. However, when the number of samples of some categories in a multi-classification dataset is too small to be processed by sampling, or the number of minority class samples is only 1 to 2, the traditional undersampling algorithms will be weakened. Methods This study selects 9 multi-classification time series datasets with extremely few samples as the objects, fully considers the characteristics of time series data, and uses a three-stage algorithm to alleviate the data imbalance problem. Stage one: Random oversampling with disturbance items increases the number of sample points; Stage two: On this basis, SMOTE (Synthetic Minority Oversampling Technique) oversampling; Stage three: Using dynamic time warping distance to calculate the distance between sample points, identify the sample points of Tomek Links at the boundary, and clean up the boundary noise.Results This study proposes a new sampling algorithm. In the 9 multi-classification time series datasets with extremely few samples, the new sampling algorithm is compared with four classic undersampling algorithms, ENN (Edited Nearest Neighbours), NCR (Neighborhood Cleaning Rule), OSS (One Side Selection) and RENN (Repeated Edited Nearest Neighbours), based on macro accuracy, recall rate and F1-score evaluation indicators. The results show that: In the 9 datasets selected, the dataset with the most categories and the least number of minority class samples, FiftyWords, the accuracy of the new sampling algorithm is 0.7156, far beyond ENN, RENN, OSS and NCR; its recall rate is also better than the four undersampling algorithms used for comparison, at 0.7261; its F1-score is increased by 200.71%, 188.74%, 155.29% and 85.61%, respectively, relative to ENN, RENN, OSS, and NCR; In the other 8 datasets, this new sampling algorithm also shows good indicator scores.Conclusion The new algorithm proposed in this study can effectively alleviate the data imbalance problem of multi-classification time series datasets with many categories and few minority class samples, and at the same time clean up the boundary noise data between classes.

This paper proposes a novel deterministic methodology for estimating the optimal sampling frequency (SF) of water quality monitoring systems. The proposed methodology is based on employing two-dimensional contaminant transport simulation models to determine the minimum SF considering all the potential changes in the boundary conditions of a water body. A two-dimensional contaminant transport simulation model (RMA4) was implemented to estimate the distribution patterns of the total dissolved solids (TDS) within the Al-Hammar Marsh in the southern part of Iraq for 30 cases of potential boundary conditions. Using geographical information system (GIS) tools, a spatiotemporal analysis approach was applied to the results of the RMA4 model to determine the minimum SF of the monitoring stations with an accuracy level of detectable change in TDS concentration (ALC) of 5%, 10% and 15%. The proposed methodology specified a minimum and maximum SF for each monitoring station (MS) that ranged between 12 and 33 times per year, respectively. Additionally, increasing the ALC to 10% and 15% increase the minimum SF for some MSs by approximately 18% and 21%, respectively. However, the proposed methodology includes all the potential values and cases of boundary conditions, which increases the certainty of monitoring the system and the efficiency of the SF schedule. Moreover, the proposed methodology can be effectively applied to all types of surface water resources.

This paper explores the application of various machine learning techniques for predicting customer churn in the telecommunications sector. We utilized a publicly accessible dataset and implemented several models, including Artificial Neural Networks, Decision Trees, Support Vector Machines, Random Forests, Logistic Regression, and gradient boosting techniques (XGBoost, LightGBM, and CatBoost). To mitigate the challenges posed by imbalanced datasets, we adopted different data sampling strategies, namely SMOTE, SMOTE combined with Tomek Links, and SMOTE combined with Edited Nearest Neighbors. Moreover, hyperparameter tuning was employed to enhance model performance. Our evaluation employed standard metrics such as Precision, Recall, F1-Score, and the Receiver Operating Characteristic Area Under Curve (ROC AUC). Regarding the F1-Score metric, CatBoost demonstrates superior performance compared to other machine learning models, achieving an outstanding 93% following the application of Optuna hyperparameter optimization. In the context of the ROC AUC metric, both XGBoost and CatBoost exhibit exceptional performance, recording remarkable scores of 91%. This achievement for XGBoost is attained after implementing a combination of SMOTE with Tomek Links, while CatBoost reaches this level of performance after the application of Optuna hyperparameter optimization.

In this paper, the spatial distribution of stony desertification characteristics and its influencing factors in Karst areas in different sampling scales are studied using a grid sampling method based on geographic information system (GIS) technology and geo-statistics, with the rock bareness rate obtained through sampling with 150m × 150m grids in the Houzhai River Basin being taken as the original data and five grid scales (300m × 300m, 450m × 450m, 600m × 600m, 750m × 750m, and 900m × 900m) as the subsample sets. The results show that the rock bareness rate does not vary much from one sampling scale to another while average values of the five sub-samples all fluctuate around the average value of the entire set. As the sampling scale is expanding, the maximum value and the average value of rock bareness rate are decreasing gradually, with a gradual increase in the coefficient of variability. In the scale of 150m × 150m, the areas of minor stony desertification, medium stony desertification, and major stony desertification in the Houzhai River Basin are 7.81 km2, 4.50 km2, and 1.87 km2, respectively. The spatial variability of stony desertification on small scales is influenced by many factors, and that on medium scales is jointly influenced by gradient, rock contents, and rock bareness rate. On large scales, the spatial variability of stony desertification is mainly influenced by soil thickness and rock bareness rate.

Diabetes is a serious health problem throughout the world, including in Indonesia. The International Diabetes Federation (IDF) reports that the number of adults with diabetes is increasing every year. The Behavioral Risk Factor Surveillance System (BRFSS) is a survey conducted by the Centers for Disease Control and Prevention (CDC) in the United States. Classification methods in data mining techniques are used to classify diabetics and non-diabetics. The data mining process is carried out by preprocessing, feature selection, and dataset classification stages. In the preprocessing stage, data cleaning, data formatting, and data oversampling are carried out using the Synthetic Minority Over-sampling Technique (SMOTE). Next, the feature selection stage is carried out using the Particle Swarm Optimization (PSO) algorithm to find the best attributes. The dataset classification stage is carried out using the CART Model Decision Tree algorithm. The results of the performance evaluation of the CART algorithm are calculated using the confusion matrix and the MAE value, the results obtained for the CART algorithm without SMOTE and PSO obtained the best accuracy of 75.34% and the MAE value of 0.2466, while the CART algorithm using SMOTE and PSO can increase accuracy by 10 .94% to 86.28% and an MAE value of 0.1372.

The special affine Fourier transform (SAFT) is a useful and powerful analyzing tool in signal processing, optics and communications. In this paper, we mainly discuss the randomized nonuniform sampling and reconstruction for random signals bandlimited in the SAFT domain. First, we show that the nonuniform sampling is identical to the uniform sampling after a pre-filter in the sense of second order statistic characters. Then, we propose an approximate reconstruction based on sinc interpolation for the nonuniform sampling of random signals bandlimited in the SAFT domain. Finally, we give the mean square error estimate for the proposed approximate recovery approach.

Recently, new semantic segmentation and object detection methods have been proposed for direct processing of three-dimensional (3D) LiDAR sensor point clouds. LiDAR can produce highly accurate and detailed 3D maps of natural and man-made environments and is used for sensing in many contexts due to its ability to capture more information and its robustness to dynamic changes in the environment. In addition, the cost of LiDAR sensors has decreased in recent years, which is an important factor for many application scenarios. The challenge with 3D LiDAR sensors like the Velodyne HDL-64E S2 is that they can output large 3D data at up to 1,300,000 points per second, which is difficult to process in real time when applying complex algorithms and models for efficient semantic segmentation. Most existing approaches are either only suitable for relatively small point clouds or rely on computationally intensive sampling techniques to reduce their size. As a result, most of these methods do not work in real-time in realistic field robotics application scenarios, making them unsuitable for practical applications. Systematic point selection is a possible solution to reduce the amount of data to be processed, but although it is memory and computationally efficient, it selects only a small subset of points, which may result in important features being missed. To address this problem, we propose a new approach to semantic segmentation in forestry that uses a systematic sampling method in which the local neighbors of each point are retained to preserve geometric details. Our approach has been shown to process up to 1 million points in a single pass. It outperforms the state of the art in efficient semantic segmentation in large datasets such as Semantic3D. We also present a preliminary study on the performance of LiDAR-only data, i.e., intensity values from LiDAR sensors without RGB values for semi-autonomous robot perception.

With the rapid development of earth observation, satellite navigation, mobile communication and other technologies, the order of magnitude of the spatial data we acquire and accumulate is increasing, and higher requirements are put forward for the application and storage of spatial data. Under this circumstance, a new form of spatial data organization emerged-the global discrete grid. This form of data management can be used for the efficient storage and application of large-scale global spatial data, which is a digital multi-resolution the geo-reference model that helps to establish a new model of data association and fusion. It is expected to make up for the shortcomings in the organization, processing and application of current spatial data. There are different types of grid system according to the grid division form, including global discrete grids with equal latitude and longitude, global discrete grids with variable latitude and longitude, and global discrete grids based on regular polyhedrons. However, there is no accuracy evaluation index system for remote sensing images expressed on the global discrete grid to solve this problem. This paper is dedicated to finding a suitable way to express remote sensing data on discrete grids, and establishing a suitable accuracy evaluation system for modeling remote sensing data based on hexagonal grids to evaluate modeling accuracy. The results show that this accuracy evaluation method can evaluate and analyze remote sensing data based on hexagonal grids from multiple levels, and the comprehensive similarity coefficient of the images before and after conversion is greater than 98%, which further proves that the availability hexagonal grid-based remote sensing data of remote sensing images. And among the three sampling methods, the image obtained by the nearest interpolation sampling method has the highest correlation with the original image.

We show how some concentration inequalities for sampling without replacement can be used for bounding future samples. This process can be extended to bound the sum of future samples from multiple populations, and we analyse an illustrative sample allocation problem.

Semi-destructive and non-destructive techniques are not commonly used for masonry as they are complex and difficult to perform. This paper describes validation of the following methods: semi-destructive and non-destructive, ultrasonic technique for autoclaved aerated concrete (AAC). The research subject was the compressive strength of AAC test elements with declared various density classes of: 400, 500, 600 and 700 (kg/m3) and various moisture levels. Empirical data including the shape and size of specimens, were established from tests on 494 cylindrical and cuboid specimens, and standard cube specimens 100×100×100 mm using the general relationship for standard concrete (Neville’s curve). The effect of moisture on AAC was taken into account while determining the strength fBw for 127 standard specimens tested at different levels of water content (w = 100%, 67%, 33% 23% and 10%). Defined empirical relations can be used to correct the compressive strength of dry specimens. For 91 specimens 100×100×100 mm, the P-wave velocity cp was tested with the transmission method using using the ultrasonic pulse velocity method with exponential transducers. The curve (fBw – cp) for determining the compressive strength of AAC elements with any moisture level (fBw) was established.

Microplastic pollution (MP) in marine environments around the globe is severe and enough precautions have not been taken so far for its prevention. The focus of this study is to quantify MPs from beach sediment and seawater samples and to identify their distribution and types along the western coast of Sri Lanka from the Kelani River estuary to the Mahaoya estuary. Nine sites along this 42 km stretch were selected and random sampling was employed to collect a minimum of 8 sediment samples from each site between October and December 2021. Water samples were also collected, parallel to the sediments, from the ocean surface. FTIR analysis revealed that most of the MPs found were polyethylene(PE), polypropylene(PP), polystyrene(PS), polyethylene terephthalate(PET), and phenol formaldehyde resin. The mean abundance of MPs varied from 2.0 ± 0.6 items/L to 161.0 ± 15.7 items/L in water samples and, from 3.0 ± 0.3 items/m2 to 656.0 ± 34.5 items/m2 in sediment samples. The MPs found were identified in different shapes as fragments (80.2%), pellets (14.9%), fibers (2.7%) and foams (2.5%). Analysis revealed that the beach sediments were contaminated with PS, phenol formaldehyde resin, PET, PP and PE, while surface seawater is dominated by phenol formaldehyde resin, PS, PP and PE.

Samples of mortar mixtures were prepared substituting the cement Portland (CPC-30R) by 0 (standard), 10 and 15% of fly ash and the structural evolution and compressive strength at 3, 7, 14 and 28 days were determined. The results for standard mortar samples showed the mineralogi-cal species portlandite, calcite, ettringite, iron oxide, silicon oxide and sillimanite. Magnetite was identified in the mixtures of mortars with portland cement substitution by 10% and 15% fly ash. The peaks corresponding to the portlandite, and ettringite showed an increase in their intensities with increasing curing time attributed to the consolidation of mineral species. The SEM tech-nique results showed that the mortar samples without fly ash addition contained mainly port-landite and ettringite while the samples with cement substitution by 10 and 15% of fly ash at 28 days further contained particles of fly ash coated with portlandite and ettringite, particles with a smooth surface and particles of fly ash with signs of attack on its surface. An increase inc was observed when the age of the mortar and the substitution of Portland cement by fly ash were increased from 3 to 28 days and from 0 to 15% respectively. The maximum value of c was reg-istered for the mortar sample with Portland cement substitution by 15% fly ash at 28 days of curing with 17.38 Mpa.

To understand functions of biomolecules such as proteins, not only structures but their conformational change and kinetics are important to be characterized but its atomistic details are hard to obtain both experimentally and computationally. We review our recent computational studies using novel enhanced sampling techniques for conformational sampling of biomolecules and calculations of their kinetics. For efficiently characterizing the free energy landscape of a biomolecule, we introduce the multiscale enhanced sampling method, which uses a combined system of atomistic and coarse-grained models. Based on the idea of Hamiltonian replica exchange, we can recover the statistical properties of the atomistic model without any biases. We next introduce the string method as a path search method to calculate the minimum free energy pathways along a multidimensional curve in high dimensional space. Finally we introduce novel methods to calculate kinetics of biomolecules based on the ideas of path sampling: One is the Onsager-Machlup action method, and the other is the weighted ensemble method. Some applications of above methods to biomolecular systems are also discussed and illustrated.

Wireline Formation Testing is an important technique in the oil field of exploration and development. Not only it can make real fluid samples of the formation directly obtained to know exactly oil existed in formation or not; but it can also show flowing pressure change to see the production capacity of the formation. So it is important measurement for formation evaluation during the drilling process and supports for activities of the exploration and development in the oil field. A numerical simulation model in this article is researched and established based on the Finite Volume Method with considering the influence of sensitive parameters such as reservoir heterogeneity, probe suction area, and mud-filtrate invasion depth during the drilling. The model is capable to design and evaluate for formation fluid sampling operations with calculating hydrocarbon content and flowing pressure. Furthermore, through case application, the performance and effect in the process of Wireline Formation Testing was demonstrated. The results indicate that this technology can be served as an effective auxiliary tool for fluid sampling operations with the function of optimizing fluid sampling measures. It can improve the accuracy of predicting indicators such as hydrocarbon content and breakthrough time during the sampling process. This study provides important backups and technical guidance for professionals in geological exploration and oilfield development.

The rapid and extensive loss of biodiversity globally has resulted in an increased urgency to capture and conserve the diversity which is present, including genetic diversity within species. However, for many species there is currently no detailed genetic data available to inform the collection and use of material held in ex situ collections and this can hamper the consideration of genetic issues and reduce the likelihood collection represent the diversity present. Even in the absence of direct genetic data, however, it is possible to consider genetic issues using the existing theoretical and empirical evidence-based and biological, ecological and demographic data for a given species. Here a framework to facilitate the consideration of genetic diversity and genetic issues, even where genetic data is lacking, is presented.

The development of low-cost, open-source Remotely Operated Vehicle (ROV) systems has provided almost unrestricted access for researchers looking to monitor the marine environment in ever greater resolution. Sampling microbial communities from the marine environment, however, still usually relies on Niskin-bottle sampling (ROV or CTD based), a method which introduces an inaccuracy and variability that is incompatible with metatranscriptomic analysis. Here, we describe a versatile, easily-replicated platform which achieves in situ mRNA preservation, via the addition of RNAlater to filtered microbial cells, to enhance ROV or CTD functionality.

Abstract: Interrupted-sampling repeater jamming (ISRJ) is a kind of intra-pulse coherent decep-tion jamming that can generate false target peaks in the range profile and interfere with the de-tection and tracking of real targets. In this paper, an anti-ISRJ method based on the intra-pulse orthogonal waveform is proposed, which can recognize common interference signals by com-paring sub-signal matched filtering results. For some special scenes where real targets cannot be directly differentiated from false targets, a new recognition method based on the energy discon-tinuity of the interference signal in the time domain is proposed in this paper. The method pro-posed in this paper can recognize real and false targets in all ISRJ modes without any prior in-formation, such as jammer parameters, with a small amount of calculation, which is suitable for actual radar systems. Simulation experiments using different interference parameters show that although this method has a 3dB loss of pulse compression gain, it can completely suppress dif-ferent kinds of ISRJ interference when the SNR before pulse compression is higher than -20dB, with 100 % target detection probability.

Zearalenone is one of the most prevalent estrogenic mycotoxins produced mainly by Fusarium family fungi, and harmed the heath of animals. Zearalenone hydrolase is an important enzyme capable of degrading zearalenone into a non-toxic compound. Although previous research has investigated the catalytic mechanism of zearalenone hydrolase, information on its dynamic interaction with zearalenone remains unknown. This study aimed to develop a pipeline for identifying the allosteric pathway of zearalenone hydrolase. Using an identity analysis, we identified hub genes whose sequences can generalize a set of sequences in a protein family. We then utilized a neural relational inference (NRI) model to identify the allosteric pathway of the protein throughout the entire molecular dynamics simulation. The production run lasted 1 microsecond, and we analyzed residues 139-222 for the allosteric pathway using the NRI model. We found that the cap domain of the protein opened up during catalysis, resembling a hemostatic tape. We used umbrella sampling to simulate the dynamic docking phase of the ligand-protein complex and found that the protein took on a square sandwich shape. Our energy analysis using both MMPBSA and PMF analysis showed discrepancies, with scores of -8.45 kcal/mol and -1.95 kcal/mol, respectively. MMPBSA, however, obtained a similar score to that of a previous report.

Species distribution models have become tools of great importance in ecology since the advanced knowledge of suitable habitat of species is needed in the process of the world's biodiversity conservation. Models that use presence-only data are of great interests and are widely used in ecology due to their easy access. However, these models do not estimate accurately the true spatial species distribution based solely on presence-only data since they do not account for biases induced by the sampling techniques used and imperfect detection. To address this gap, Hierarchical integrated models have been recently introduced. Through this study, we assessed the relative performance of these new SDMs models using simulated data. The performance of the models was tested by comparing the estimates of parameters of the distribution models they provide with parameters used to simulate the distribution of the virtual species. The best model was the one whose estimates were close to the true distribution parameters of the virtual species. Results showed that analyzing Presence-only data in conjunction with Point-counts data through the Dorazio's Hierarchical model produced estimates of the coecients of the species intensity models with high precision and less bias while the Koshkina integrated model showed poor performance. Site-occupancy data, being not informative of species abundance, did not allow reducing biases in Presence-only data. The Dorazio's Hierarchical model produced estimates with high precision even with low detection probability. We have also found that the species rarity tends to in ate the variability of the models' estimates making modelling abundant species to be more accurate than modelling less abundant species. Hence, to model the species distribution with high precision based on Presence-only data, additional Point-counts data are required to account for sampling bias and imperfect detection.

Tuning nonlinearity of the laser is the main source which will deteriorate the spatial resolution in optical frequency domain reflectometry system. We develop methods for tuning nonlinearity correction in the OFDR system from the aspects of data acquisition and also the posting-processing. A zero-crossing detection scheme is researched and implemented by a customized circuit. Equal-spacing frequency sampling is therefore achieved in real-time. The maximum sensing distance can reach to the same length of the auxiliary interferometer. The zero-crossing detection for the beating frequency of 20MHz is achieved. Then, a nonlinearity correction method based on the self-reference method is proposed. The auxiliary interferometer is no longer necessary in this scheme. The tuning information of the laser is extracted by a strong reflectivity point at the end of the sensing arm in the main interferometer. The tuning information can then be used to resample the raw signal and the nonlinearity correction can be achieved. The spatial resolution test and the distributed sensing experiments are both performed based on this nonlinearity correction method. The results validated the feasibility of the proposed method. The method reduces the hardware and data burden for the system and has a potential value on the system integration and miniaturization.

Efficient utilization of biomass requires conversion into forms that can be optimally applied in energy generation. Briquetting involves compaction of biomass into solid blocks that are more efficient than raw biomass and provides for ease of transport and handling. These are improved when the briquettes possess high shatter index and compressive strength. Due to difference in nature and composition, it is imperative to define optimum conditions for the production of quality and durable briquettes for individual biomass compacted into briquettes. This study studied the effects of process variables on the strength and durability of biomass briquettes produced using Abura sawdust. The lateral compressive strength and drop shatter index were investigated whilst varying the temperature (100-150 °C), pressure (9-15 MPa) and hold time (15-30 min). The compressive strength ranged between 2.06 and 5.15 MPa whilst the shatter index was between 50 and 600. The pressure was significant to the determination of the compressive strength (p < 0.1) and the shatter index (p < 0.05). Mechanical characteristics of the binderless Abura sawdust briquettes can be improved by optimizing the densification variables during the briquetting process when moderate pressures are used for compaction.

Large scale cropland erosion rates mapping and dynamic monitoring are critical for agricultural planning but extremely challenging. In this study, by using field investigation data collected from 20,155 land parcels in 2,781 sample units in the National Soil Erosion Survey, land use change data for two decades from the National Land Use/Cover Database of China (NLUD-C), we proposed a new point to surface approach to quantitatively assess long-term cropland erosion based on the CSLE model and non-homogeneous voting. The results show that cropland in Yunnan suffers from serious problem with unsustainable mean soil erosion rate of 40.47t/(ha·a) and erosion ratio of 70.11%, which are significantly higher than those of other land types. Engineering control measures (ECMS) have a profound impact on reducing soil erosion, soil erosion rate of cropland with and without ESMs differs by more than five times. Over the past two decades, the cropland area in Yunnan continues to decrease, with a net reduction of 7461.83 km2 and a ratio of −10.55%, which causes corresponding 0.32×108 t (12.12% ) decrease in cropland soil loss. We also quantified the impact of different LUCC scenarios on cropland erosion, and extraordinarily high variability was found in soil loss in different basins and periods. Conversion from cropland to forest contributes the most to cropland erosion reduction, while conversion from grassland to cropland contributes 56.18% of the increase in soil erosion. Considering the current speed of cropland regulation, it is the sharp reduction in land area that leads to cropland erosion reduction rather than treatments. The dilemma between the Grain for Green Policy and Cropland Protecting Strategy in mountainous areas should be treated carefully with shared understanding and collaborations from different roles.

Despite the long history of using protein sequences to infer the tree of life the potential for different parts of protein structures to retain historical signal remains unclear. We propose that it might be possible to improve analyses of phylogenomic datasets by incorporating information about protein structure; we test this idea using the position of the root of Metazoa (animals) as a model system. We examined the distribution of “strongly decisive” sites (alignment positions that support a specific tree topology) in a dataset comprising >1,500 proteins and almost 100 taxa. The proportion of each class of strongly decisive sites in different structural environments was very sensitive to the model used to analyze the data when a limited number of taxa were used but they were stable when taxa were added. As long as enough taxa were analyzed, sites in all structural environments supported the same topology (ctenophores sister to other animals) regardless of whether standard tree searches or decisive sites were used to select the optimal tree. However, the use of decisive sites revealed a difference between the support for minority topologies for sites in different structural environments; buried sites and sites in sheet and coil environments exhibited equal support for the minority topologies whereas solvent exposed and helix sites had unequal numbers of sites supporting the minority topologies. Given the plausible trees equal support for minority topologies is consistent with discordance among gene trees, making it possible the relatively slowly evolving buried (and sheet and coil) sites are giving an accurate picture of the true species tree as well as the amount of conflict among gene trees. Alternatively, the apparent support could reflect currently uncharacterized processes of molecular evolution. Regardless, it is clear that analyses of the deepest branches in the animal tree of life using sites in different structural environments are associated with a subtle data type effect that results in distinct phylogenetic signals.

Acute Oak Decline (AOD) is complex syndrome affecting Britain’s keystone native oak species, (Quercus robur L. and Q. petraea L. (Matt.) Liebl.), in some cases causing mortality within five years of symptom development. The most distinguishable symptom is weeping stem lesions, from which four species of bacteria have been isolated: Brenneria goodwinii, Gibbsiella quercinecans, Lonsdalea britannica and Rahnella victoriana. We do not yet know where else these bacteria exist, and little is known about the relationship of the wider oak leaf microbiome (phyllosphere) to acute oak decline. Here we investigate whether incidental evidence from a large oak genome re-sequencing dataset could be used to detect these bacteria in oak foliage, and whether bacterial incidence co-varied with AOD status or location. Oak leaves and buds were sampled from 421 trees at five sites in England. Whole genomic DNA from these samples was shot-gun sequenced with short reads. Non-oak reads were extracted from these data and queried to microbial databases. Reads uniquely matching AOD-associated bacterial genomes were found to be present on trees from all five sites and included trees with active lesions, trees with historic lesions and trees without AOD symptoms. The abundance of the AOD-associated bacteria did not differ between tree health categories but did differ among sites. We conclude that the AOD-associated bacteria may be members of the normal oak microbiome, whose presence on a tree is not sufficient to cause AOD symptoms.

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID-19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing the amount of relatively expensive UV resin, and iv) enabling production of handle on more accessible material extrusion 3-D printers. A modular open source UV LED box was designed, fabricated for $45 and tested for batch curing. Swabs can be fabricated for $0.06-$0.12/swab. The results of the mechanical validation tests showed that the swabs could withstand greater forces than would be expected in normal clinical use. The swabs were also able to absorb a significant amounts of synthetic mucus materials and passed abrasion and handling tests. The results show the open source swab are promising candidates for clinical trials.

(1) Background: Childhood immunization is vital for preventing morbidities and mortalities globally. However, rural Pakistan is facing persistent challenges, particularly after recent global health crises in gauging accurate vaccination coverage estimates. This study aimed to apply a novel Lot Quality Assurance Sampling (LQAS) methodology due to its rapid and reliable estimates of the routine immunization rates among children aged 12-23 months old in Shikarpur, Sindh, and to identify priority areas for future interventions. (2) Methods: A cross-sectional household survey design was adopted for an in-depth assessment of vaccination coverage in a previously under-studied rural context. (3) Results: Data were collected from 1,402 children aged 12-23 months across 47/49 Union Councils in Shikarpur within 141 randomly identified clusters. LQAS was innovatively employed along with GIS Mapping which provided a spatial analysis of the distribution of immunization coverage and the spot map of clusters. The weighted average for fully immunized children was 42.4% after applying Direct Adjustment Method. A steep decline in coverage for each successive vaccine dose was observed, and 39 key priority areas were identified on GIS-based plotting for intensive health interventions. Multivariate Logistic Regression Model further revealed informational gaps and fear of side effects as major barriers to achieving complete immunization. (4) Conclusions: The innovative application of LQAS and GIS Mapping in this study has provided a comprehensive glimpse of its utility in future follow-ups and similar assessments. The findings stress the critical need to tackle the foundational reasons behind the vaccination gaps, with a special focus on enhancing awareness and information dissemination in the key priority areas.