Hollow and concrete-filled steel tubes (CFSTs) are widely used as columns in many structural systems and local buckling can occur when they are subjected to axial compression loading. The critical regions for the local buckling of the columns are near the ends of the column where the moments are the highest. To strengthen the critical regions of the CFSTs the CFRP provides a simple and effective method which used previously as an enhancement for both of strength and ductility. So, this study suggests investigating the axial load behaviour of CFST strengthened with CFRP using FE method after a verification study and then a various parametric studies were carried out to cover the effect of the CFRP layers, number, confinement length and position. The FE results proved that, one CFRP sheet with thickness equal to 1.2 mm was strengthened the composite column by 8.5%, two CFRP sheets with total thickness equal to 2.4 mm was strengthened the composite column by 23.5%, three CFRP sheets with total thickness equal to 3.6 mm was strengthened the composite column by 35.1% and four CFRP sheets with total thickness equal to 4.8 mm was strengthened the composite column by 44.5%. Moreover, this study proved that by strengthened the composite columns with CFRP sheets with different lengths, the axial load resistance was improved by 8.5%, 4.6%, 0.1% and 0.0% for length percentages 100%, 75%, 50% and 25% respectively.

Concrete-filled steel tube (CFST) members have been widely used in the field of civil engineering due to their advanced superior mechanical properties. However, internal defects such as concrete core voids and interface debonding are likely to weaken the load-carrying capacity and stiffness of these members, which affects safety and serviceability of CFST structures. Visualizing the inner defects of concrete core in CFST members have been a critical need in civil engineering construction, a travel time tomography (TTT) is introduced to quantitatively identify and visualize the sizes and positions of CFST members in this paper. Moreover, a parameter analysis is performed to investigate the relationship between TTT imaging qualities and influence factors, e.g. inversion parameters, defect sizes and positions. The effectiveness and accuracy of the TTT algorithm are verified by several numerical examples and the results demonstrate that TTT can identify the sizes and positions of concrete core void defects in CFST members efficiently and several inversion parameters including model weighting matrix and inversion grid size really pose a significant impact on the imaging results of CFST members. In addition, several optimum parameters are recommended to benefit the future study of the promising TTT approach for CFST members.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

Concrete-filled steel columns have been extensively used in the world due to having all suitable characteristics of concrete and steel, more ductility, increasing concrete confinement using steel wall, large energy-absorption capacity and appropriate fire behavior. In present paper, concrete-filled steel square columns have been simulated under the influence of blast load using ABAQUS software. These responses will be compared for scaled distances based on the distance to source and weight of explosive material. As result, it can be seen that although concrete deformation has been restricted using steel tube, but inner layer of concrete has been seriously damaged and column displacement will be decreased by increasing scaled distance. We also concluded that concrete-filled steel columns have high ductility and blast resistance.

The BP neural network and PSO algorithm are applied into analyzing the reliability of long-span Concrete Filled Steel Tubular (CFST) arch bridges. Firstly, using BP neural network to fit the structural performance function. And then the PSO method was used to calculate the reliability index. A long-span Concrete Filled Steel Tubular arch bridges reliability indices were calculated whether considering the geometric nonlinearity or not. The calculation and analysis results showed that the BP neural network and PSO algorithm compensated the deficiency of the traditional reliability analysis methods, improved the calculation accuracy, provided a new thought and means for the research on the reliability of long-span bridge structure, and well applied to the reliability analysis of long-span Concrete Filled Steel Tubular arch bridges. Additionally, the reliability analysis of long-span Concrete Filled Steel Tubular arch bridges on service limit state must consider the geometric nonlinearity effect, or the results will tend to be unsafe.

The first Network Arch Bridge (NAB) was opened to traffic 60 years ago and since then the idea spread around the world. It is a type of a tied arch bridge that combines the benefits of tied arch bridges and trusses in a single system, thus it has a very good stiffness even in the case of extremely slender structures. In a Network Arch the hangers are inclined and some of them intersect each other at least twice. The core of a NAB is the hanger arrangement that minimizes the bending moment in the arch to very small values, leading thus to compression in the arch. This paper reviews the Network Arch idea devised by prof. Tveit and extended by researchers and engineers worldwide. A comprehensive review of the literature about the Network Arch is provided and the situation of NABs around the world from the standpoint of location, span, structural system used for the cross-section, bridge type (road, railway, combined or pedestrian) and opening year is discussed.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

Epoxy asphalt (EA) concrete is widely used in constructing long-span steel bridge pavements (SBDPs). This study aims to derive a fatigue damage evolution law, conducting an experimental investigation of SBDP. First, a general theoretical form of the fatigue damage evolution law of materials is established based on the thermal motion of atoms. Then, fatigue experiments demonstrate that this evolution law well represents the known damage–life relationships of SBDP. Taking into account the experimental relationships between damage and fatigue life under symmetrical cyclic loadings with different overload amplitudes and temperature variations, a detailed damage evolution law is deduced. Finally, the role of damage accumulation is discussed on the basis of the proposed damage evolution law for the extreme situation of heavy overload and severe environments. The results show that both heavy loading and falling temperatures increase the fatigue damage of SBDP considerably; therefore, SBDP should avoid heavy loading combined with winter temperatures. EA shows a fatigue life two to three times longer than that of modified matrix asphalt (SMA) or guss asphalt (GA). For the same thickness, EA pavement is demonstrated to be more suitable for an anti-fatigue design of large-span SBDP under high traffic flows and low temperatures.

The use of polyolefin fibre reinforced concrete (PFRC) as an alternative for reducing or even eliminating the reinforcing steel bars employed in reinforced concrete has become real in the past years. This contribution analyses the improvements in sustainability that a change in the aforementioned reinforcement configuration might provide in a flyover bridge. Economic, environmental and social parameters of both possibilities were studied by means of the integrated value model for sustainable assessment use (Modelo Integrado de Valor para una Evaluación Sostenible, MIVES) used in Spain, which is a multi-criteria decision-making method based on the value function concept and the seminars delivered by experts. The results of the MIVES method showed that the use of PFRC in combination with reinforced concrete (RC) has a sustainability index 22% higher. An analysis of the parameters that form this evaluation shows that there are no remarkable differences in the financial costs between the two possibilities studied. Nevertheless, social and environmental aspects provide with a better qualification the option of building a bridge by using PFRC combined with RC.

The purpose of this study is to propose a consecutive manufacturing process system to secure the productivity of excellent STKN540B steel tube in the respect of economy and safety as the supporting material for mega structures such as building, bridge and ship. The components of consecutive manufacturing are press-bending, orbital auto welding and steel tube correction. By using STKN540B a high-strength steel material with low yield point that requires a special manufacturing process unlike other steel materials, an actual tube manufacturing is carried out at each stage in this experimental study. With this, the quality of steel tube and the efficiency of the manufacturing process are analyzed to draw out some points to improve in the future.

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

The organic coating of bridge steel girders is subjected to physical scratches, corrosion, and aging in natural weathering. The breakdown of the coating may cause serviceability and safety problems if left unnoticed. A hyperspectral imaging method is proposed to detect the condition of steel coatings based on coating-responsive features in reflectance spectra. A field test was conducted on the real-world bridge which shows obvious signs of degradation. The hyperspectral signature enables an assessment of the coating health and defect severity. The results indicated that the coating scratch can be effectively located in the domain of a hyperspectral image and the scratch depth can be determined by mapping a scratch depth indicator (SDI=R532nm / R641nm). Rust sources and products in steel girders can be identified by the unique spectral signatures and the rust stains (and thus stain areas) scattered on the coating can be pinpointed at pixel level by the corrosion rust indicators. The chemical integrity of a topcoat is demonstrated by the short-wave infrared spectroscopy and the topcoat degradation can be evaluated by the absorption at 8000 cm-1 and 5850 cm-1.

Sugar-sweetened beverages are associated with metabolic dysfunction, particularly in those with increased risk factors. Artificial sweeteners (AS) are often promoted as a healthier alternative, yet findings remain conflicting as to their effects on metabolic function. Further, there is a lack of data exploring the interaction between AS and high-fat diets (HFD). We therefore examined the effects of HFD and the AS Acesulfame-potassium (Ace-K) on glucose intolerance and adipose tissue physiology in male and female C57BL/6 mice. 40 mice were randomised to receive either a) a control diet (CDCon; standard control diet/water), b) control diet and Ace-k (CDAS; CD/7.5mM AS in drinking water), c) HFD (HFCon; HFD (45%kcal from fat)/water), or d) HF and AS (HFAS; HFD/7.5mM AS in drinking water) for 6 weeks. A HFD increased body weight in male and female mice independently of AS supplementation. AS induced sex-specific effects protecting against HFD-induced hyperglycaemia and adipocyte hypertrophy in male mice and reducing inflammatory gene expression in the adipose tissue. Conversely in females, AS induced hyperinsulinemia in HFD mice and increased expression of immune-related genes. These findings suggest that supplementation of HFD with AS exacerbates metabolic dysfunction in female mice. This work supports the importance of studying sexually dimorphic responses to an altered nutritional environment and highlights the need for further investigation into the intake of AS, particularly in those already at risk of metabolic disease such as the obese or overweight.

Background: Fiber-reinforced composites (FRCs) have been proposed as an alternative to traditional metal alloys for the realization of frameworks in full-arch implant supported prostheses. The aim of the present in vitro study was to evaluate the deflection under load of seven prostheses endowed with frameworks made of different materials, including different types of fiber reinforced composites (FRCs). Methods: A master cast with four implant analogues in correspondence of the two lateral incisors and the two first molars was used to create full-arch fixed prostheses with the same shape and different materials. Prostheses were made in different materials (framework+veneering material): gold alloy+resin (Au+R), titanium+resin (Ti+R), FRC with multi-directional carbon fibers+resin (ICFRC+R), FRC with unidirectional carbon fibers+composite (UCFRC+C), FRC with glass fibers+resin (GFRC+R), FRC with glass fibers+composite (GFRC+C), resin (R, full-acrylic prosthesis). Flexural tests were conducted using Zwick/Roell Z 0.5 machine and the deflection of the lower surface of the prosthesis was measured in order to obtain load/deflection graphs. Results: Greater rigidity and less deflection were recorded for UCFRC+C, GFRC+C, followed by Ti+R, and Au+R. The greatest deformations were observed for resin alone, ICFRC+R and GFRC+R. The results were slightly different in the incisal region probably due to the greater amount of veneering material in this area. Conclusions: When used to realize full-arch frameworks, Au and Ti allow a predictable mechanical behavior with gradual deformations with increasing load. UCFRC also demonstrated good outcomes and less deflection than ICFRCs when loaded. The GFRC full-arch framework may be a valid alternative, however showed greater deflections. Further studies are needed in order to evaluated how different prosthesis design and material thickness might affect the outcomes.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

The welding and construction processes of H-type thick-plate-bridge steel involve complex multi-pass welding processes, which is difficulty to ensure its welding performance. Accordingly, it is crucial to explore the inherent correlation among the welding processes parameters and welding quality, and applied it into the welding robots, eliminating the instability from manual welding. In order to improve the welding quality, the GMAW (Gas Metal Arc Welding) welding process parameters are simulated using the Q345qD bridge steel flat joint model. Four welds with X-shaped grooves are designed to optimize the parameters of welding current, welding voltage, and welding speed. The optimal welding process parameters are investigated through thermal-elastic-plastic simulation analysis and experimental verification. The results indicate that when the welding current is set to 230A, the welding voltage to 32V, and the welding speed to 0.003m/s, the maximum deformation of the welded plate is 0.52mm, with a maximum welding residual stress of 345MPa. Both the simulation results of multi-pass welding and experimental tests meet the welding requirements, as they show no excessive stress or strain. These parameters can be applied into building large steel frame bridges with welding robots, improving the quality of welded joints.

The research object was the stress-strain state of shear stud bonds in the contact joint of steel-concrete beams. The work diagrams for three types of anchors are given. Based on the analysis of numerical and full-scale experiments, analytical dependencies are proposed that reflect the actual operation of anchor ties. Comparisons of the calculation results by analytical formulas and comparisons with numerical and full-scale experiment data are given. Numerical studies have revealed the pattern of the stress-strain state of the contact joint, the stages of development of cracks in the concrete flange, and the sequence of development of deformations in anchor ties. It was revealed that vertical shear studs bonds have an increased bearing capacity, although displacements are 1.5-2 times greater than those of loop-shaped anchor ties.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

China is facing the development requirements of the dual carbon goal and the construction needs of resilient cities. Currently, high-strength composite structural systems are a feasible solution, but their research and application in the construction field are insufficient, especially for the combination forms of concrete above C100 and steel above Q550. In response to this issue, this paper proposes a new high-performance structural system, namely the composite frame - high-strength steel plate wall core tube resilient structure system, which includes high-strength steel plate (Q550) - ultra-high strength concrete (C100) shear walls, replaceable energy dissipation coupling beams, and composite frames. Taking a 200 meter building as an example, this paper designs and establishes calculation models for a conventional reinforced concrete frame-core tube structure and a high-performance structure based on PKPM software, and establishes elastoplastic analysis models for both based on SAUSAGE software, and then conducts dynamic elastoplastic time history analysis and seismic resilience assessment of structures under design basis earthquakes (DBEs), maximum considered earthquake (MCEs) and extremely rare earthquakes (EREs). Research has shown that compared to conventional structures, new high-performance structures can effectively reduce the size of shear walls, reduce the self-weight of the structure, and enhance the space for building use; The story drift ratio has higher redundancy than specification limits, lower plastic damage and overall stiffness degradation of the structure, and better seismic performance; The seismic resilience has significantly improved, especially in the case of casualties, which can better ensure the safety of people's lives and property.

This paper presents the experimental and numerical study on a ductile beam-column connection between a composite reinforced concrete truss (CRCT) beam and Concrete Filled Tube (CFT) column subjected to bending and shear loads. Two experimental models with different beam-column joint testing schemes, extracted from the same prototype three-dimensional structure designed according to the rules of the capacity design provided by seismic code, were subjected to quasi-static cyclic tests by applying gravitational loads and the horizontal seismic force. The main objective of this paper is to verify the experimental ductile behavior of both specimens and to simulate the experimental global and local response by nonlinear static analysis considering different modelling approaches. The comparison between the experimental and numerical results highlights, for both models considered, the ductile and dissipative capacity of the connection system, designed following the criterion of the hierarchy of resistances proposed by the current Italian code. Different experimental setup showed similar results demonstrating the repeatability of the test and its reproducibility through the nonlinear numerical analysis.

The literature has well established prestressing in concrete beams and its calculation procedures. However, its use in composite steel-concrete beams has increased despite main normative codes lacking a specific approach for it. Designers must, in most cases, combine the available criteria to calculate the standards of steel and reinforced concrete structures. This study aimed to formulate this optimization problem and analyze CO2 emissions for the optimal design of composite steel-concrete beams with external prestressing. The design variables for the optimization problem include cross-section of laminated or welded profiles, slab height, characteristic strength of concrete to compression, and number of tendons. We obtained a solution for the optimization problem via a genetic algorithm (GA) and a particle swarm optimization one (PSO). Comparative analysis with experimental example and with optimization problem of prestressed steel beam are performed. An parametric analysis to several spams is performed, which enabled to evaluate the factors that most impact CO2 emissions. According to results, the chosen algorithms effectively obtained solutions for the problem, and PSO usually provided better results than GA. Regarding the final solution composition, steel contributes the most to emissions, welded profiles provided better solutions than laminated ones, and laminated spans of up to 17.5m and welded ones up to 27.5m dispensed with tendons.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

Adding steel fibers to concrete improves the capacity in tension-driven failure modes. An example is the shear capacity in steel fiber reinforced concrete (SFRC) beams with longitudinal reinforcement and without shear reinforcement. Since no mechanical models exist that can fully describe the behavior of SFRC beams without shear reinforcement failing in shear, a number of empirical equations have been suggested in the past. This paper compiles the existing empirical equations and code provisions for the prediction of the shear capacity of SFRC beams failing in shear as well as a database of 487 experiments reported in the literature. The experimental shear capacities from the database are then compared to the prediction equations. This comparison shows a large scatter on the ratio of experimental to predicted values. The practice of defining the tensile strength of SFRC based on different experiments internationally makes the comparison difficult. For design purposes, the code prediction methods based on the Eurocode shear expression provide reasonable results (with coefficients of variation on the ratio of tested to predicted results of 27% - 29%). None of the currently available methods properly describe the behavior of SFRC beams failing in shear. As such, this work shows the need for studies that address the different shear-carrying mechanisms in SFRC and its crack kinematics.

One of the influential factors in estimating the service life of reinforced concrete bridges (RCB) is determining the long-term seismic performance of these structures. Corrosion due to chloride ion diffusion leads to the destruction of critical members of the RCB during the useful life of the structure. So, the long-term seismic performance of the bridge deteriorates as a result. It is essential to study the effect of corrosion deterioration on the long-term seismic performance of bridges in the southern regions of Iran, near the coasts of the Persian Gulf and the Oman Sea, because of the seismicity of the region and high corrosion rate of reinforced concrete (RC) members is the result of environmental conditions. In order to investigate this issue, considering studies about environmental conditions of southern Iran, the onset time of corrosion in the columns, as seismic critical members of the bridge, was determined. Based on that, the corrosion's effect on characteristics of RC at specific time points during the bridge's useful life (0, 15, 30, 45, 60, 75 and 90 years) have been calculated. The effects of corrosion include deterioration of the core and cover concrete properties, steel bar and the connection between concrete and steel bar. In the next step, at each time point, according to the modified stress-strain relationships, the moment-curvature analysis of the bridge pier was done, and the properties of the plastic hinge were determined. Finally, based on the obtained data about plastic hinge characteristics at each time point, overload analysis of the bridge was performed in both longitudinal and transverse directions. Then the capacity curves of RCB were compared at the mentioned time-points. The results show that the capacity of the bridge deteriorates over time due to corrosion. Therefore, a proposal to increase the value of base shear design has been made to ensure the long-term seismic performance of RCB in corrosive environments.

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

The steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings, and those used for multistory housing in particular. However, the effectiveness of steel damper columns may be affected by the behavior of surrounding members, and this effect can be severe in the case of seismic sequences. This article investigates the nonlinear response of building models having an RC moment-resisting frame (MRF) with and without steel damper columns under seismic sequences. The applicability of the concept of the momentary energy input to the prediction of the peak response of RC MRFs with damper columns under seismic sequences is also investigated. The main findings of the study are summarized as follows. (1) The peak response of RC MRFs with damper columns subjected to sequential accelerations is similar to the peak response obtained considering only the mainshock, whereas the cumulative strain energy of RC MRFs accumulates more for sequential accelerations. (2) The steel damper column is effective in reducing the peak and cumulative responses of RC MRFs in the case of sequential seismic input. (3) The relation of the hysteretic dissipated energy during a half cycle of the structural response and the peak displacement of the first modal response can be properly evaluated using the simple model proposed in this study.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

The present paper describes a study case of the failure investigation of Duplex stainless steel (UNS S31803) on the tube and tube sheet section of a shell and tube heat exchanger BEM TEMA type with seawater as the cooling medium. Although UNS S31803 offers high strength, high resistance to chloride-induced SCC, and high resistance to pitting attack in chloride environments, in this study case, the heat exchanger experienced some material degradation; 26 tubes were leaked and plugged on both sides, and scales plugged 76 tubes. The examination in this study case revealed the formation of biofilm inside the tubes, XRD examination revealed that the film contained aragonite (CaCO3), and by using microstructural examination on the inner surface of the tube, the austenite grains were preferentially attacked by crevice corrosion. In this case, the failure was caused by crevice corrosion, and crevice corrosion was enhanced by microbiological-induced corrosion (MIC). Recommendations to avoid similar failures are also suggested in this paper.

Several factors impact the durability of concrete bridge decks, including traffic loads, fatigue, temperature changes, environmental stress, and maintenance activities. Detecting problems such as corrosion, delamination, or concrete degradation early on can lower maintenance costs. Nondestructive evaluation (NDE) techniques can detect these issues at early stages. Each NDE method, meanwhile, has limitations that reduce the accuracy of the assessment. In this study, multiple NDE technologies were combined with machine learning algorithms to improve the interpretation of half-cell potential (HCP) and electrical resistivity (ER) measurements. A parametric study was performed to analyze the influence of five parameters on HCP and ER measurements, such as degree of saturation, corrosion length, delamination depth, concrete cover, and moisture condition of delamination. The results were obtained through finite element simulations and used to build two machine learning algorithms, a classification algorithm and a regression algorithm, based on the Random Forest methodology. The algorithms were tested using data collected from a bridge deck in the BEAST® facility. Both machine learning algorithms were effective in improving the interpretation of ER and HCP measurements using data from multiple NDE technologies.

In the broad field of Inverse Analysis and Structural Identification, it is nowadays of a large interest the study of Gaussian Processes, as a reliable and efficient optimisation method, particularly helpful toward the identification of a global optimum point, under the conditions of complicated functions to be optimised. In the present contribution, a specific case study is considered, focusing on a historical road reinforced concrete arched bridge, located in Northern Italy, employing dynamic modal properties, deciphered from in-situ measurements, previously acquired under operational traffic conditions, by a standard wired accelerometer system, placed at the deck level. Aiming at the identification and diagnosis of the bridge structure, three main methodological steps are herein considered: the adoption of a FEM model of the structure (in the linear dynamic framework), the definition of an appropriate discrepancy function, based on measured and numerically computed quantities (natural frequencies and mode shapes of the bridge), and the investigation of such a discrepancy function, toward a consistent selection of an optimisation strategy for the identification of sought parameters (Young’s moduli and mass densities of diverse elements of the structure). The presented developments, within the framework of methodological optimisation approach by Gaussian Processes, and achieved results display a rather efficient perspective, with reference to the considered case study, toward inverse analysis for structural diagnosis, in the context of strategic (historical) infrastructures.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

This paper analyzed the main diseases of the friction high-strength bolt (FHSB) joints in order to study the characteristics of the corrosion products of the joints in steel bridge and the influence factors. Seven representative FHSB connection pairs and eight steel plate samples were selected from the Dongying Shengli Yellow River Bridge, which has been in operation for 33 years. Then Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and X-Ray Diffraction (XRD) were used to analyze the microscopic morphology and chemical composition of the corroded surface of the samples. Finally, this paper discussed the relationship between the corroded sample surface and the environmental corrosion. The research results showed that construction quality problems, such as non-standard hole expansion, segmental slab joint dislocation and contact surface pollution, accelerated corrosion of the contact surface. With the increase of corrosion degree of joints, the contact surface of aluminum spraying layer gradually changed from a rugged and dense state to a smooth and porous powder state. With the corrosion of the steel plate substrate, the contact surface gradually changed from a fluffy stratified state to a surface bonding state. It was inferred that the friction coefficient of the FHSB connection node on the corroded aluminum sprayed contact surface first decreased and then increased. The corroded node samples detected not only a large number of S and Cl elements, but also the oxides of Mn, Si and other elements as well as FeS. It was speculated that node corrosion was also related to atmospheric (acid rain) and industrial dust and other corrosive environments. Almost all samples detected the component SiO2 of the Yellow River soil, as well as Mg, Ca, K, Na and other elements at the same time, which is basically consistent with the component elements of the Yellow River soil. Therefore, it was inferred that it was related to the inclusion of the Yellow River soil.

Fungal infection of grape berries (Vitis vinifera) by Botrytis cinerea frequently coincides with harvest, impacting both the yield and quality of grape and wine products. A rapid and non-destructive method for identifying B. cinerea infection in grapes at an early stage prior to harvest is critical to manage loss. In this study, zeolitic imidazolate framework-8 (ZIF-8) crystal was applied as an absorbent material for volatile extraction from B. cinerea-infected and healthy grapes in a vineyard followed by thermal desorption gas chromatography-mass spectrometry. The performance of ZIF-8 to absorb and trap targeted volatiles was evaluated with a standard solution of compounds and with a whole bunch of grapes enclosed in a glass container to maintain standard sampling conditions. Results from sampling methods were then correlated to B. cinerea infection in grapes as measured and determined by Genus specific antigen quantification. Trace levels of targeted compounds reported as markers of grape B. cinerea infection were successfully detected with in-field sampling. Peak area counts for volatiles 3-octanone, 1-octen-3-one, 3-octanol, and 1-octen-3-ol extracted using ZIF-8 were significantly higher than values achieved using Tenax®-TA from field testing and demonstrated good correlation with B. cinerea infection severities determined by B. cinerea antigen detection.

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

Expansion tube is ideal energy absorber which dissipates kinetic energy through plastic deformation and friction. There is an urgent need to understand the influence of key parameter, e.g. semi angle, tube material, and friction coefficient, on the mechanical response and energy absorption characteristics of expansion tube. In the present work, the material properties of the tubes were tested under quasi-static loading condition, and the numerical simulations were carried out by using commercial software ABAQUS. Based on the validated finite element simulation, all the semi angle, tube material, and friction have significant effects on the energy absorption capacity of expansion tube. The expansion tube with high tensile stress of parent material have high energy absorption capacity, while the specific energy absorption is linear with the tensile stress/density of tube material. This work would give a guidance to the structural design and parent materials selection for expansion tubes.

This research aimed to improve the interpretation of electrical resistivity (ER) results in concrete bridge decks by utilizing results from multiple nondestructive evaluations (NDE) techniques in machine learning algorithms. To achieve this, a parametric study was first conducted using numerical simulations to investigate the effect of various parameters on ER measurements, such as the degree of saturation, corrosion length, delamination depth, concrete cover, and the moisture condition of delamination. A data set from this study was used to build a machine-learning algorithm based on the Random Forest methodology. This algorithm was then implemented on data collected from a bridge deck in the BEAST® facility. The presented results demonstrate an improvement in the interpretation of ER measurements using data from other NDE technologies.

This paper uses probability method to evaluate the fire safety performance of prestressed steel-concrete beam bridges based on simulation experimental research. Firstly, fire simulation experimental sample analysis was conducted on actual small box girder bridges to obtain the structural response of prestressed steel-concrete structures under fire, which is in line with engineering practice. Next, construct a reliability analysis model for the fire resistance performance of prestressed steel-concrete beam bridges; Combining reliability theory with finite element method, establish a reliability analysis method for the fire resistance performance of prestressed steel-concrete beam bridges. Subsequently, a safety factor evaluation model for the fire resistance performance of prestressed steel-concrete beam bridges was proposed, and a safety factor evaluation method for the fire resistance performance of prestressed steel-concrete beam bridges based on reliability back analysis was established. Finally, based on the analysis of the structural response after a fire in a specific case of a simply supported to continuous prestressed steel-concrete continuous beam bridge project, a structural resistance sample of the prestressed steel-concrete beam bridge is generated through uniform design method, and statistical analysis is conducted. Subsequently, probability methods are used to evaluate the safety of the prestressed steel-concrete beam bridge after a fire. Through analysis, it can be concluded that the time of fire has a significant impact on the structural performance of prestressed steel-concrete beam bridges, and the randomness of parameters has a significant impact on the safety reserve of prestressed steel-concrete beam bridges after fire. It is necessary to pay attention to it in specific engineering practice and strengthen the monitoring and statistics of structural random characteristics.

The objective of this study is to measure the crack propagation speed in three types of self-compacting concrete reinforced with steel fibers loaded under four different loading rates. Central-notched prismatic beams with two types of fibers (13 mm and 30 mm in length), three fiber volume ratios, 0.51%, 0.77% and 1.23%, were fabricated. Four strain gages were glued on one side of the specimen notch to measure the crack propagation velocity, a fifth one at the notch tip to estimate the strain rates upon the initiation of a cohesive crack and the stress-free crack. A servo-hydraulic testing machine and a drop-weight impact device were employed to conduct three-point bending tests at four loading-point displacement rates, the former to perform tests at 2.2 μm/s, 22 mm/s and the latter for those at 1.77 m/s, 2.66 m/s, respectively. With lower fiber contents, smooth mode-I cracks were formed, the crack speed reached the order of 1 mm/s and 20 m/s. However, crack velocities up to 1417 m/s were obtained for the concrete with high content of fibers under impact loading. This value is fairly close to the theoretically predicted terminal crack velocity of 1600–1700 m/s. Numerical simulations based on cohesive theories of fracture and preliminary results based on the technique of Digital Image Correlation are also presented to complement those obtained from the strain gages. In addition, the toughness indices are calculated under all four loading rates. Strain hardening (softening) behavior accounting from the initiation of the first crack is observed for all three types of concrete at low (high) loading rates. Significant enhancement in the energy absorption capacity is observed with increased fiber content.

The use of new developed high-strength steel in concrete members can reduce steel bars congestion and construction costs. This research aims to study the behavior of concrete columns reinforced with new developed high-strength steel under eccentric loading. Ten reinforced concrete columns were fabricated and tested. The test variables are transverse reinforcement amount and yield strength, eccentricity, and longitudinal reinforcement yield strength. The failure patterns are compression and tensile failure for columns subjected to small eccentricity and large eccentricity, respectively. The same level of post-peak deformability and ductility only can be obtained with lower amount of transverse reinforcement when high-strength transverse reinforcements are used in columns subjected to small eccentricity. The high-strength longitudinal reinforcement can improve bearing capacity and post-peak deformability of concrete columns. Besides, three different equivalent rectangular stress block (ERSB) parameters in predicting bearing capacity of columns with high-strength steel were discussed based on test and simulated results. It is concluded that the Code of GB 50010-2010 overestimates the bearing capacity of columns with high-strength steel, whereas bearing capacities computed using Codes of ACI 318-14 and CSA A23.3-04 agree well with test results.

Structures inevitably suffer damages after an earthquake, with their severity ranging from minimal damages to non-structural elements to partial or even total collapse, possibly with loss of human lives. Thus, it is essential for engineers to understand the crucial factors that drive a structure towards suffering higher degrees of damage, so that preventative measures can be taken. In the present study, we focus on three well-known damage thresholds, namely Collapse Limit State, Ultimate Limit State and Serviceability Limit State and analyze which of the features obtained via Rapid Visual Screening, determine whether or not a given structure will cross that threshold. To this end, we use Machine Learning to perform binary classification for each damage threshold, as well as Explainability via SHAP values (acronym for SHapley Additive exPlanations) to quantify the effect of each parameter. The quantitative results obtained demonstrate the potential applicability of ML methods to re-calibrate the computation of structural vulnerability indices using data from recent earthquakes.

Damage assessment is one of the most crucial issues for bridge engineers, especially for existing steel bridges. Among several methodologies, the vibration measurement test is a typical approach in which the natural frequency variation of the structure is monitored to detect the existence of damage. However, locating and quantifying the damage is still a big challenge. In this regard, the artificial intelligence (AI)-based approach seems a potential way to accomplish those obstacles. This study deploys a comprehensive campaign to determine all dynamic parameters of a pre-damage steel truss bridge structure. Based on the results of mode shape, natural frequency, and damping ratio, a finite element model (FEM) is created and keeps updating. The artificial intelligence network's input data will be analyzed and evaluation from damage cases. The trained artificial neural network model will be curated and evaluated to confirm the approach's feasibility. During the actual operational stage of the steel truss bridge, this damage assessment system is showing good performance in terms of monitoring the structural behavior of the bridge under some unexpected accidents.

Acoustic emission monitoring (AEM) has emerged as an effective technique for detecting wire-breaks resulting from, e.g., stress corrosion cracking, and its application on prestressed concrete bridges is increasing. The success of this monitoring measure depends crucially on a carefully designed sensor layout. For this the attenuation of elastic waves within the structure’s material is determined ideally in-situ through object-related measurements with a reproducible signal source, typically a rebound-hammer. This assumes that the attenuation coefficients derived from rebound-hammer tests are comparable to those from wire-breaks, thus allowing their results to be directly applied to wire-break detection without further adjustments. This study challenges this assumption by analysing attenuation behaviour through an extensive dataset. Employing time-domain and frequency analysis, the research generates attenuation profiles from laboratory experiments and in-situ measurements across various girders and bridge structures, extracting the slope and standard deviation of the residuals. While generally validating this approach, the findings highlight differences in attenuation behaviour from among wire-break signals and rebound-hammer impulses, whereby the latter potentially underestimates the relevant attenuation of wire-breaks by approximately 20 %. Consequently, a transfer factor is proposed to adjust object-related measurement results for wire-break scenarios, including a variance of 1.0 dB/m to cover a 95 % confidence interval for sample scattering. Moreover, the anisotropic attenuation behaviour across different structures was studied, showing that transverse attenuation consistently exceeds the longitudinal, significantly influenced by structural features such as voids. In prefabricated concrete bridges with in-situ-cast concrete slabs, transverse signal transmission remains unhindered across multiple elements. Finally, the results provide a valuable reference for the design of sensor layouts in bridge monitoring, particularly benefiting scenarios where direct in-situ experiences are lacking.

In this paper, we consider a fourth-order suspension bridge equation with nonlinear damping term |u_t|^m-2u_t and source term |u|^p-2u. We give necessary and sufficient condition for global existence and energy decay results without considering the relation between m and p. Moreover, when p>m, we give sufficient condition for finite time blow-up of solutions. The lower bound of the blow-up time T_max is also established. It worth to mention that our obtained results extend the recent results of Wang (J. Math. Anal. Appl., 2014) to the nonlinear damping case.

Steel fibre reinforced concrete (SFRC) consists of short hooked steel fibres randomly distributed and oriented within the cementitious matrix. The contribution of fibre in bridging cracks to provide the stress transfer required relies upon the orientation of the fibre in the concrete. Bridging fibre aligned with a crack are less effective than those inclined to it. Therefore, understanding the pull-out behaviour of misaligned fibre is a key factor to quantify and optimize the design of SFRC in the structural applications. In the laboratory a single oriented fibre embedded in a solid cylinder of concrete is subjected to a pull-out test where the axis of a tensile force is aligned with the axis of the cylinder. Based upon the observed behaviour this paper presents a new analytical bounding approach to capture the pull-out response of misaligned hooked-end steel fibre embedded in a concrete matrix. The analysis is based upon a transversely isotropic condition assumed for the plasticity that occurs in the cold drawn fibre. The model accounts for the influence of fibre diameter and the combined strengths of the steel and concrete. The model predictions have also been compared with other experimental results published in the literature. The results showed that the model can predict pull-out loads reasonably for different fibre orientations between bounds of failure derived from the strengths of the two constituents. A critical orientation is observed at maximum strength. Therein, an understanding of the pull-out behaviour of misaligned, hooked-end fibres is necessary to optimize the strength of concrete from this method of reinforcement.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

The aim of this investigation is focused on the effects of hooked-end steel fibers on both fresh and hardened properties of modified self-compacting concretes (SCC). For this purpose, the steel fibers are associated with other residues contents (i.e. marble, granite and rubber). This concatenated materials contents constitutes a novelty since no investigations are reported. It is found that the increase of rubber content, a better ability to absorb energy is observed. This indicates that a good alternative of structural material is provided. Fresh properties are evaluated by using flow, T500 time, V-funnel, J-ring methods. The mechanical behavior is evaluated in terms of compressive strength, tensile strength, static and dynamic modulus of elasticity, and damping ratio. Experimental results of the water absorption, porosity and density are also attained. It is also found that a SCC mixture containing steel fiber, marble/granite residue and rubber content is a potential mixture to be considered when in SCC designing associated with improved damping ratio. Although the rubber content decreases the mechanical behavior and slump flow, the concatenated utilization of MGR and steel fiber contents provide a slight improve in the damping result. An environmental benefit can also be associated since the cement consumption is decreased with marble additions.

A steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings and multistory housing. To assess the seismic performance of buildings with steel damper columns, the peak displacement of the whole building and the energy dissipation demand of the dampers must be evaluated. This article proposes an energy-based prediction procedure for the peak and cumulative response of an RC frame building with steel damper columns. The proposed procedure considers two energy-related seismic intensity parameters, namely the maximum momentary input energy and the total input energy. The peak displacement is predicted considering the energy balance during a half cycle of the structural response, using the maximum momentary input energy. The energy dissipation demand of the dampers is then predicted considering the energy balance during a whole response cycle using the total input energy. The local responses (e.g., peak drift, maximum plastic rotation of beams, maximum shear strain, and energy dissipation demand of dampers) are predicted using pushover analysis. Numerical analysis results for 8- and 16-story RC buildings show that the proposed prediction method achieves satisfactory accuracy.

Conditional heteroskedastic financial time series are commonly modelled by (G)ARCH processes. ARCH(1) and GARCH were recently established in C[0,1] and L^2[0,1]. This article provides sufficient conditions for the existence of strictly stationary solutions, weak dependence and finite moments of (G)ARCH processes for any order in C[0,1] and L^p[0,1]. It deduces explicit asymptotic upper bounds of estimation errors for the shift term, the complete (G)ARCH operators and the projections of ARCH operators on finite-dimensional subspaces. The operator estimaton is based on Yule-Walker equations, and estimating the GARCH operators also involves a result estimating operators in invertible linear processes being valid beyond the scope of (G)ARCH. Moreover, our results regarding (G)ARCH can be transferred to functional AR(MA).

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) buildings and are often used for multistory housing. The evaluation of the peak deformation and hysteretic dissipated energy of such building structures is essential for the rational seismic design of RC buildings with SDCs. In a previous study, the authors proposed an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for high quality predictions. In this article, the V_ΔE1^*–D₁^*_max relationships of RC moment-resisting frames with and without SDCs are invested using a critical pseudo-double impulse (PDI) analysis based on a study by Takewaki and coauthors. The results show that the V_ΔE1^*–D₁^*_max relationship obtained from the critical PDI analysis agrees well with that calculated from the equations proposed in the previous study.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

The response of structures under pulse-like ground motions is characterized by the large amount of energy input in a few cycles. Consequently, structures with insufficient strength may suffer severe damage owing to excessive deformation. In a previous paper, the energy-based prediction procedure for the peak and cumulative response of a reinforced concrete (RC) frame building with steel damper columns was proposed (Fujii and Shioda, 2023). Although this procedure was verified by comparison to the nonlinear time-history analysis (NTHA) results, the performance of the proposed procedure with pulse-like ground motion records has not been verified yet. In this study, the accuracy of the energy-based prediction procedure for an RC frame building with steel damper columns was investigated by considering pulse-like ground motions. The numerical analysis results reveal that the accuracy of the predicted peak response is satisfactory, which agrees with the results of the author’s previous study. However, the accuracy of the predicted total input energy to the building model depends on the ratio of the pulse period of the ground motion to the effective fundamental period of the building model. The reasons for this underestimation of the total input energy are discussed in this paper.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

A new algorithm is developed in this study to automatically detect reinforced concrete structures' rebar locations and diameters using the ground penetrating radar technique. The method approximates the hyperbolic signatures using two-way travel time and bi-quadratic equations. The study includes formulating electromagnetic wave speed in reinforced concrete (RC) structures. The algorithm was used in a computer code to provide an automated analysis of ground-penetrating radar data collected from a pre-planned survey grid. Two RC slabs were fabricated and tested to validate the proposed method. The proposed method is efficient in signal processing and accurately and reliably determining the rebar information.

This paper presents a numerical study on the vertical (axial) and lateral (flexure) behavior of CFST (Concrete-Filled Steel Tube) columns with active hoop prestress; this transverse prestressing effect is achieved by bolting together two steel half-tubes. This study refers to new construction only (i.e., no retrofit). 12 prototype CFST column specimens (segments) are analyzed. These specimens differ in the prestressing force (3 levels) and in the gravity loading ratio (4 levels); they are selected to represent typical ground columns of mid-rise buildings. The structural behavior of these column specimens is simulated with a nonlinear model implemented in Abaqus; the concrete and steel behavior are described with a damage-plasticity and a plasticity model, respectively. Finally, the interface concrete-steel interaction is represented by a hard (compression-only) surface-to-surface contact model. The calculations involve three consecutive loading steps: (i) transverse prestress, (ii) axial force, and (iii) lateral loading (shear force and bending moment). The structural behavior of the CFST columns is deeply examined and discussed; the results show that their axial-flexural capacity is adequate. Noticeably, it is concluded that the overall benefits of prestressing the columns are only modest. Preliminary studies on the aforementioned mid-rise buildings equipped with the CFST columns show that their gravity and wind capacities are largely enough; conversely, their seismic capacity is sufficient for moderate seismic ground motions only.

The opened beams always confused the designers due to the guidelines missing. In this research, six hybrid reinforced beams reinforced with mixed steel and basalt fiber reinforced polymer (BFRP) bars had constant cross-sections of 150mm x 300mm and a clear span of 1800mm. Generally, five beams have symmetrical rectangular openings with dimensions of 150mm x 250mm located at a distance of 250mm (equivalent to the beam effective depth) from the beam support in addition to a solid beam that is served as a control reference. The studied parameters included the effect of using internal reinforcement (steel or BFRP bars) provided along the opening or by incorporating an external BFRP sheet around the opening corners. Also, the conduction of double enhancement with internal steel reinforcement bars further external strengthening BFRP sheet was investigated. The relevant results showed that the opened beam without enhancement lost almost 74.66% of the maximum load compared with the solid beam. Placing internal steel or BFRP bars around the openings increased the maximum load by 62.07% and 59.68%, respectively in comparison to the non-enhanced opened beams. Using an external BFRP sheet to strengthen the opening corners of the beam enhanced the maximum load by 76.39% compared with the non-enhanced opened beam. Therefore, if the beam double enhancement with an external BFRP sheet and internal steel reinforcement around the openings, the maximum load increased by 137.40% compared with the non-enhanced opened beam. Ultimately to further analyze the experimental results and confirm their findings, the study was extended to include the numerical analysis using three dimensional finite element modeling and the results correlated very well with the experimental ones.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

This study reveals the essential load-bearing characteristics of the steel-concrete composite floor system under fire conditions applying structural stressing state theory. Firstly, the strain data in the entire process of the fire test are modeled as state variables which can present the slab’s stressing state evolution characteristics; Then, the state variables are used to build the stressing state mode and the parameter characterizing the mode. Further, the Mann-Kendall criterion is adopted to detect the leap points in the evolution curves of the characteristic parameters during the entire fire exposure process. Also, the evolution curves of the stressing state modes are investigated to verify the leap profiles around the leap/characteristic points; Finally, the detected leap points are defined as the failure starting points and elastoplastic branching points, which is unseen in the past researches focusing on the failure endpoint defined at the ultimate load-bearing state of the composite floor system. The failure starting point and the elastoplastic branching point are the embodiment of natural law from quantitative change to quality change of a system rather than an empirical and statistical judgment. Hence, both characteristic points avoidably exist in the strain data of the composite floor system undergoing the fire process, which can be revealed through the proper modeling methods and update the existing theories and methods on structural analysis and design in fire.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material

The assessment of existing bridges constitutes a serious challenge for the researchers since their safety evaluation is a complex task due to several sources of uncertainty affecting the parameters identified in the knowledge process. In particular, a high level of uncertainties may arise in the case of prestressing systems requiring special investigation strategies and experimental technologies. The paper aims to investigate how the knowledge uncertainties influence the safety assessment of existing post-tensioned bridges. The semi-probabilistic approach is used, and uncertainties related to the knowledge process are described considering the number of tests, the confidence level assumed for the estimation of the problem parameters, and the measurement errors of in-situ tests. Results concerning a typical post-tensioned bridge are reported and the variability of the outcomes is discussed and compared with a reference case of “perfect knowledge”. The main results of the study confirm the general robustness of the semi-probabilistic Eurocodes safety format and provide an overview of dispersion due to different choices about the number of tests and confidence level. The measurement errors may lead to significant under-estimation of the computed structural capacity with respect to the reference one.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

Polymer nanocomposites are composed of polymer materials reinforced with nano fillers. In the present study the effective thermal conductivity of the composites filled with nanofillers has been investigated using commercially available finite element software ABAQUS 6.11. The nanofillers used were alumina particles and multi-walled carbon nanotubes (MWNTs) and the matrix was considered to be made of epoxy. For the analysis 2D and 3D Representative Volume Elements (RVEs) were generated using Random Sequential Adsorption (RSA) algorithm using MATLAB and Python scripts. Thermal conductivity was found out for 2D and 3D RVEs for different area and weight fractions respectively. Two different shapes of the alumina nanoparticles were considered: spherical (circular) and ellipsoidal (elliptical) for 3D (2D) analysis. It was found that the thermal conductivity was increased with the addition of nanofillers. The increase in thermal conductivity was approximately same for both types of inclusions at corresponding area or weight fractions in 2D or 3D analysis. The results showed that addition of MWNTs to the composites lead to a significant increase in thermal conductivity than spherical or ellipsoidal inclusions.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

Steel damper columns (SDCs) are energy-dissipating members that are suitable for reinforced concrete (RC) moment-resisting frames (MRFs) and those often used for multistory housing. In a previous study, an energy-based prediction procedure for the peak and cumulative response of an RC frame building with SDCs was proposed. In this procedure, the accuracy of the equivalent velocity of the maximum momentary input energy (V_ΔE1^*)–peak equivalent displacement (D₁^*_max) relationship is essential for improved prediction. In this article, the seismic capacity curve (V_ΔE1^*–D₁^*_max relationship) of RC MRFs with and without SDCs is evaluated using incremental critical pseudo-multi impulse analysis (ICPMIA). In the ICPMIA, which is based on a study by Takewaki and coauthors, the structure is subjected to various intensities of critical pseudo-multi impulsive lateral force. An ICPMIA of four 8- and 16-story RC MRFs with and without SDCs is performed to obtain their structural behaviors under various intensities of pulsive input. Then, the seismic capacity curve obtained from the ICMPIA results are compared with the predicted results based on the simplified equations. The main findings of this article are as follows. (i) The seismic capacity curve of RC MRFs without SDCs strongly depends on the number of impulsive lateral forces (N_p). As N_p increases, the seismic capacity decreases. The predicted seismic capacity curve severely underestimates that obtained from the ICMPIA in the case of large N_p. This trend is notable when the level of pinching behavior in the RC members is severe. (ii) In the case of an RC MRF with SDCs, however, the influence of N_p on its seismic capacity curve is small. The predicted seismic capacity curve agrees very well with that obtained from the ICMPIA. The influence of the level of pinching behavior in RC members on the seismic capacity curve is small.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

Prestressed concrete sleepers (or railroad ties) are principally designed in order to carry wheel loads from the rails to the ground of railway tracks. Their design takes into account static and dynamic loading conditions. In spite of the most common use of the prestressed concrete crossties in railway tracks, there have always been many demands from rail engineers to improve serviceability and functionality of concrete crossties. For example, signaling, fiber optic, equipment cables are often damaged either by ballast corners or by tamping machine. There has been a need to re-design concrete crosstie to cater cables internally so that they would not experience detrimental or harsh environments. Also, many concrete crossties need a retrofit for automatic train control device and similar signaling equipment. In contrast, the effects of holes and web openings on structural capacity of concrete crossties have not been thoroughly investigated. This paper accordingly highlights the effect of holes and web openings on the toughness and ductility of concrete crossties. The outcome of this research enables better decision making process for retrofiting prestressed concrete crossties with holes and web opening in practice.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

Sulfur, peroxide and combined sulfur and peroxide curing systems were applied for cross-linking of unfilled and carbon black filled rubber compounds based on ethylene-propylene-diene-monomer rubber. The results revealed that the type of curing system influenced the course and shape of curing isotherms. This resulted in the change of curing kinetics of rubber compounds. The cross-link density of vulcanizates cured with combined vulcanization systems was lower than that for vulcanizates cured only in the presence of sulfur or peroxide system. The results revealed good correlation between the cross-link density as well as the structure of the formed cross-links and physical-mechanical characteristics of the materials. It can be stated that by proper combination of vulcanization systems it is possible to modify tensile behavior of vulcanizates in targeted manner. On the other side, dynamical-mechanical properties were found not be significantly influenced by the composition of curing system.

The tribology behavior, tribofilm formation and structure evolution of polytetrafluoroethylene (PTFE) filled with α-Al2O3 and SiO2 nanoparticles during sliding against steel counterparts under different loads were studied. It is found that both composites exhibit good wear resistance across the pressure of 1 MPa to 10 MPa, with the α-Al2O3/PTFE composite demonstrates better performance stability compared to the SiO2/PTFE composite. The high wear resistance is attributed to the formation of tribofilms at the friction interface. For the α-Al2O3/PTFE, an island-like tribofilm is formed with a thickness ranging from 100 to 200 nm, while the tribofilm of the SiO2/PTFE composite is thinner, measuring approximately 50 to 100 nm, and manifest a striped pattern. The chemical composition, both at the surface and subsurface levels, as well as the morphology of the tribofilms were studied using FTIR spectrometry, X-Ray photoelectron spectroscopy (XPS), and FIB-TEM. It is found that the difference in thickness and microstructure of the tribofilms for the two composites is mainly due to the tribochemistry of the nanoparticles. The α-Al2O3 nanoparticle plays a "cohesion" role during the formation of the tribofilm, which facilitates the formation of a thicker, more uniform, and stronger adhered tribofilm on the metallic counterpart, making it more robust against higher shear stress.

Chronic kidney disease (CKD) and cardiovascular disease (CVD) are highly prevalent conditions, each significantly contributing to the global burden of morbidity and mortality. CVD and CKD share a great number of common risk factor, such as hypertension, diabetes, obesity, and smoking among others. Their relationship extends beyond these factors, encompassing intricate interplay between the two systems. Within this complex network of pathophysiological processes, vitamin D has emerged as a potential linchpin, exerting influence over diverse physiological pathways implicated in both CKD and CVD. In recent years, scientific exploration has unveiled a close connection between these two prevalent conditions and vitamin D, a crucial hormone traditionally recognized for its role in bone health. This article aims to provide an extensive review of vitamin D's multifaceted and expanding actions concerning its involvement in CKD and CVD.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

The objective of this paper is to present a mathematical formalism that states a bridge between Physics and Psychology, concretely between analytical dynamics and personality theory in order to open new insights in this theory. In this formalism energy plays a central role. First, the short-term personality dynamics can be measured by the General Factor of Personality (GFP) response to an arbitrary stimulus. This GFP dynamical response is modelled by a stimulus-response model: an integro-differential equation. The bridge between Physics and Psychology is provided when the stimulus-response model can be formulated as a linear second order differential equation and, subsequently, reformulated as a Newtonian equation. This bridge is strengthened when the Newtonian equation is derived from a minimum action principle, obtaining the current Lagrangian and Hamiltonian functions. However, the Hamiltonian is a non-conserved energy. Then, some changes provide a conserved Hamiltonian function: the Ermakov-Lewis energy. This energy is presented, as well as the GFP dynamical response that can be derived from it. An application case is presented: an experimental design in which 28 individuals consumed 26.51 g of alcohol. This experiment provides an ordinal scale for the Ermakov-Lewis energies that predicts the effect of a single dose of alcohol.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

In the context of post-harvest pest management in agricultural products, the adoption of modified atmospheres presents an eco-friendly alternative to conventional pesticides. This study focuses on nitrogen gas as a potential agent for insect control in stored commodities, utilizing computational simulations to investigate its penetration and distribution within two common storage configurations: chamber-contained pallets and silos. By employing the convection-diffusion equation, the simulations reveal insights into nitrogen distribution dynamics and duration required for oxygen reduction. The results highlight the influence of boundary conditions, commodity porosity, and convection effects on nitrogen dispersion. In chamber scenarios, boundary condition type significantly affects oxygen reduction time, while in silos, convection and diffusion interact to establish a consistent diffusion layer thickness. This research enhances the understanding of modified atmosphere techniques and their potential for sustainable pest management. It provides practitioners with valuable quantitative insights, paving the way for optimized modified atmosphere strategies in real-world agricultural contexts.

This paper presents a study to accurately evaluate defects in reinforced concrete decks using ultrasonic pulse-echo signals. Two validation specimens were designed and tested where reinforced concrete deck slab specimens included planned voids and defects. A commercial Ultrasonic Pulse-Echo (UPE) device obtains 2-D images of the void/defect locations of the reinforced concrete deck. The UPE is based on the ultrasonic shear-wave test method using dry-point-contact transmitting and receiving transducers and employing a synthetic aperture focusing technique. The authors analyzed the recorded UPE A-scan data to enhance the accuracy of estimating the defects' locations using the synthetic aperture focusing technique imaging method. The analysis benefitted from an advanced denoising approach and defect echo peak extraction based on empirical modal decomposition, Hurst exponent characterization, and Hilbert envelope estimation. While output from conventional UPC devices can only provide qualitative results, the new method provides quantitative information on the anomalies inside the reinforced concrete deck. The developed approach accurately assists with assessing the location and depth of the voids/defects in the reinforced concrete deck slabs.

The study presents a comparative approach between response surface methodology (RSM) and hybridized, genetic algorithm artificial neural network (GA-ANN) in predicting the water absorption, compressive strength, flexural strength split tensile strength and slump for steel fiber reinforced concrete. The effect of process variables such as aspect ratio, water cement ratio and cement content were investigated using the central composite design of response surface methodology. This same experimental design was used in training the hybrid-training approach of artificial neural network. The predicting ability of both methodologies were compared using the root mean sqaured error (RMSE), mean absolute error (MAE), model predictive error (MPE) and absolute average deviation (AAD). The RSM model was found more accurate in prediction compared to hybrid GA-ANN.

Although various atmospheric corrosion simulation models have been developed that give good results, industrial environments are still challenging. This paper aims to investigate the effect industrial atmospheres in Bor on the mechanical properties of structural steel S235JR and to create a constitutive model and also laboratory experimental conditions that will give the best results as an accelerated corrosion test. Atmospheric corrosion tests lasted six months, using sites close to the Electrolytic Refining Plant and Sulphuric Acid Plant, as well as air quality monitoring stations at a remote location in the city of Bor. The laboratory experiments included a salt chamber test lasting 120 h and 240 h and immersing the specimen in the electrolyte from the Electrolytic Refining Plant for 30 days. The results were compared with the standard specimens stored in the laboratory. The X-ray diffraction (XRD) method was used to identify the composition of corrosion products. The scanning electron microscopy (SEM) analysis was applied to analyze the fracture surfaces of the specimens. The use of the Complete Gurson Model (CGM) described the tensile characteristics of the corroded specimens. The study has shown that an enhanced acceleration model and conditions could be developed using numerical analysis of the test results.

On the analyzed section of 2.4 km of the national road No. 50 of the Młodzieszyn bypass, it was carried out by a consortium of OAT and SAT companies in the period April-September 2019, under constant traffic in the field of repairing the concrete pavement by replacing slabs, levelling them and sealing expansion joints, roughening and roadside reinforcements.

The preparation and thermal properties of polypropylene foils, filled with ceramic microparticles, talc or boron nitride, are described. A slow, linear increase of thermal conductivity with volume percent of filler up to 30 vol % is detected. Reduction of the foil thickness bellow 200 micrometers leads to a significant increase of thermal conductivity. Specific thermal capacities of foils are temperature dependent, they decrease with filler incorporation.

The present review paper aims at collecting and discussing the research work, numerical and experimental, carried out in the field of Fluid-Structure Interaction (FSI) in one-dimensional (1D) pressurized transient flow in the time-domain approach. Background theory and basic definitions are provided for the proper understanding of the assessed literature. A novel frame of reference is proposed for the classification of FSI models based on pipe degrees-of-freedom. Numerical research is organized according to this classification, while an extensive review on experimental research is presented by institution. Engineering applications of FSI models are described and historical accidents and post-accident analyses documented.

A membrane ozonation contactor was built to investigate ozonation using tubular membranes and to inform computational fluid dynamics (CFD) studies. Non-porous tubular polydimethylsiloxane (PDMS) membranes of 1.0 – 3.2 mm inner diameter were tested at ozone gas concentrations of 110 – 200 g m−3 and liquid side velocities of 0.002 m s−1 – 0.226 m s−1. The dissolved ozone concentration could be adjusted to up to 14 mg O3 L−1 and increased with decreasing membrane diameter and liquid side velocity. Experimental mass transfer coefficients and molar fluxes of ozone were 1.1∙10−5 mol m−2 s−1 and 2.4∙10−6 m s−1, respectively, for the smallest membrane. CFD modelling could predict the final ozone concentrations but slightly overestimated mass transfer coefficients and molar fluxes of ozone. Model contaminant degradation experiments and UV absorption measurements of ozonated water samples in both ozone (O3) and peroxone (H2O2/O3) reaction systems in pure water, river water, wastewater effluent and solutions containing humic acid show that the contactor system can be used to generate information on the reactivity of ozone with different water matrices. Combining simple membrane contactors with CFD allows predicting ozonation performance under a variety of conditions leading to improved bubble-less ozone systems for water treatment.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.