This study aimed to estimate scattered radiation and its spatial distribution around three Cone Beam Computed Tomography (CBCT) devices, in order to determine relatively safe positions for an operator to stand if needed to be inside the CBCT room. The following devices were tested: Morita Accuitomo (CBCT1), Newtom Giano HR (CBCT2), Newtom VGi (CBCT3). Scattered radiation measurements were performed using different kVp, mA and Field of View (FOV) options. An anthropomorphic phantom (NATHANIA) was placed inside the x-ray gantry to simulate clinical conditions. Scattered measurements were taken with the ionization chamber Inovision model 451P Victoreen once placed at fixed distances from each irradiation isocenter, away from the primary beam. A statistically significant (p<0.001) difference was found in the mean value of the scattered radiation estimations between the CBCT devices. Scattered radiation was reduced with a different rate for each CBCT device as distance was increased. For CBCT1 the reduction was 0.047μGy, for the CBCT2 0.036 μGy and 0.079 μGy for CBCT3, for every one meter away from the x-ray gantry. Therefore, at certain distances from the central x-ray, the scattered radiation was below the critical 1mGy. Consequently, an operator could stay inside the room accompanying the patient being scanned, if necessary.

Introduction Cone Beam Computed Tomography (CBCT) scans should be digitally oriented using a reference plane before being evaluated for patient growth and treatment outcome. Current orientation planes are usually dependent on the Porion points. Using more reliable landmarks than the Porion, we introduce the Acta plane and investigate its reliability as an alternative reference plane for cases in which the Porion point is inaccessible. Methods To test its reliability, a dental student and an orthodontist located sixteen skeletal and dental landmarks in sixteen CBCT scans, before and after reorientation. Also, four measurements were calculated based on these landmarks’ coordinates. The reorientation of these CBCT scans with the Acta plane was done by another dental student. Intraclass Correlation Coefficient (ICC) was calculated before and after orientation, intra- and inter-examiner. The data were tested for significance through the Shapiro Wilk test with a threshold set at 0.05. Through the ICC variation of the points’ coordinates, this article also evaluated the reliability of this plane with the t-paired and exact-sign tests. Results: The identification of landmarks was more reliable in the reoriented CBCT images than in the original images, with a significant increase of 0.012 in the median of the ICC. Linear and angular measures showed no significant differences between groups. Conclusion This plane is a reliable alternative for the orientation of CBCT images. The design of the Acta plane might allow the use of a smaller field of view and, consequently, a reduction in the radiation dose.

Osteoarthritis (OA) is a prevalent disease and the leading cause of pain, disability, and quality of life deterioration. Our study sought to evaluate the image quality and dose of cone-beam com-puted tomography arthrography (CBCT-A) and compare them to digital radiography (DR) for OA diagnosis. Overall, 32 cases of CBCT-A and DR with OA met inclusion criteria and were prospectively analyzed. The Kellgren and Lawrence classification (KLC) stage, sclerosis, osteo-phytes, erosions, and mean joint width (MJW) were compared between CBCT-A and DR. Image quality was excellent in all CBCT-As, with excellent inter-observer agreement. OA un-der-classification was noticed with DR for MJW (p=0.02), osteophyte detection (<0.0001), and KLC (P<0.0001). The HU values obtained for the CBCT did not correspond to the values for MDCT, with a greater mean deviation obtained with the MDCT HU for MBIR1 than MBIR2. CBCT-A has been found to be more reliable for OA diagnosis than DR as revealed by our results using three-point rating scale for the qualitative image analysis, with higher quality and an ac-ceptable dose. Moreover, the use of this imaging technique permits the preoperative assessment of extremities in OA diagnosis, the upright position and bone microarchitecture analysis being two other advantages of CBCT-A.

Since the development of CBCT had been utilized in dentistry, the images of the CBCT can assist the surgeon to evaluate the anatomy carefully. Despite the value of the radiology evaluation, the implant procedures may require additional consideration rather than only evaluating the anatomical factors. The purpose of this study is to evaluate the predictability of using CBCT alone to plan for implant placement on the edentulous patient digitally CBCT images were analyzed by clinicians, measuring the ridge heights and widths of 4 selected implant sites in the maxillary and 2 selected implant sites in the mandibular arches for 91 patients planning for the implant-supported overdenture. (A total of 47 patients out of the 91 had completed the implant placement on the edentulous ridge, contributing to 55 upper and/or lower arches (136 dental implants). . Both predictabilities are low, implying the CBCT planning for implant placement on the edentulous ridge is not a good index and is insufficient to predict the surgical procedures as a solo method. The finding of this study indicates that digital planning by CBCT is insufficient to serve as an individual tool to predict implant procedures. Further information and evaluation must be considered for implant placement on the edentulous ridge.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

Objective. The present study examined the potential use of computed tomography panoramic mandibular indices on cone beam CT (CBCT) for the assessment of bone density in postmenopausal women with low bone mass. Study design. We enrolled 104 postmenopausal women who performed dual energy X-ray absorptiometry (DXA) using a DXA scanner and mental foramen region CBCT using NewTom VGi EVO Cone Beam 3D system. We assessed the relationship between DXA parameters: lumbar, femoral neck and total hip T score, bone mineral density (BMD), and lumbar trabecular bone score (TBS) and the panoramic mandibular indices: computed tomography mandibular index superior (CTI(S)), computed tomography mandibular index inferior (CTI(I)) and computed tomography mental index (CTMI). Results. We found important correlations between the CTI(I), CTI(S) and CTMI and bone mass, quantitative evaluated as BMD and T-score and also quality using TBS score. Conclusion. CBCT measured indices CTI(S), CTI(I), CTMI are useful in assessing patients with low bone mass.

Background/Objectives: This study aims to investigate the influence of root canal morphology and various treatment variables on the outcomes of root canal treatments (RCT) in mandibular second molars, assessed through cone-beam computed tomography (CBCT) imaging. Methods: A total of 150 CBCT images were examined, comprising 100 cases of persistent endodontic infections and 50 from previously treated root canals with normal apices in mandibular second molars. CBCT was utilized to evaluate root canal configuration, the radiographic quality of coronal restorations and treated canal systems, and the presence of periapical lesions. Statistical analyses were performed to explore correlations between these factors. Results: The presence of a C-shaped root canal configuration did not demonstrate a significant correlation with periapical lesions (p=0.05). Factors influencing endodontic treatment outcomes included the presence of missing canals (p=0.018), underfilling or overfilling (p=0.045), and inadequate coronal restoration (p=0.006). The presence of a missing canal was identified as the variable most significantly associated with periapical lesions (OR=3.103). Leaky canals were more commonly observed in C-shaped root canals (p&lt;0.001). Conclusions: Regardless of the root canal morphology of mandibular second molars, successful RCT depends on thorough disinfection to eliminate any untreated canals, precise three-dimensional filling of the canals at the correct working length, and a securely sealed coronal restoration to prevent leakage.

Background and Objectives: The prevalence of osteoporosis is high, reportedly affecting 200 million people worldwide. A major problem associated with osteoporosis is that femoral fractures cause a decline in general function and loss of independence, greatly reducing patients’ quality of life. Notably, osteoporosis is an asymptomatic chronic metabolic disease, and its detection is thus often delayed. Interestingly, mandibular cortical index (MCI) classification using dental panoramic radiography is reportedly useful for early detection of osteoporosis. However, this visual classification method can lead to differences in diagnosis among surgeons. Therefore, this preliminary study was performed to analyze cone-beam computed tomography (CBCT) data and examine an objective MCI classification using the findings obtained. Materials and Methods: MCI classification (classified as C1, C2, or C3) was performed by three examiners on 70 women (91 sites) aged ≥20 years. The mandibular cortical width of all sites was measured using CBCT images. Results: The results showed that the mandibular cortical width was not particularly correlated with age or number of present teeth, and no significant quantitative differences were found between C1 and C2. However, coronal CBCT images of C2 revealed multiple characteristic bone trabecular structures. Conclusions: These structures may be an important finding affecting the classification of two-dimensional dental panoramic radiography images.

The knowledge of the precise anatomy and dimensions of the pulp chamber in the different teeth allows the odontologist to perform correct diagnosis, as well as treatment planning and moni-toring. The clinical practice has introduced cone-beam computed tomography (CB-CT) as a method to evaluate the morphology and dimensions of the pulp chamber. Nevertheless, micro-computed tomography (micro-CT) is regarded as the gold standard in approaching those topics. Here we have designed an algorithm that takes as input DICOM images from in vivo CB-CT of permanent molars to determine the accuracy CB-CT for evaluation of pulp chamber volume. The values were compared with those from in vivo CB-CT (rough and expert manipulated) and ex vivo micro-CT. The relative errors obtained with the volume calculated by the algorithm vs. the volume measured by micro-CT do not exceed 5.7%; also, no significant differences were found between algorithm volumes vs. manipulated CB-CT volumes while all volumes were different from those obtained with automatic CB-CT software. These data demonstrate that volume algorithm CB-CT based may be a reliable technique for evaluation of the pulp chamber volume in permanent molars and can be useful in the diagnosis of pulp diseases, as well as in the planning and monitoring of their treatments.

(1) Background: This retrospective cohort study aimed to investigate the cephalometric evaluation of facial height ratio (FHR) and growth patterns. (2) Methods: We assessed facial height ratios, Y-axis to SN angle, and growth patterns in 94 participants from Timis county using digital cephalograms. Participants were categorized based on Angle’s classification. Cephalograms were digitally traced and analyzed using WebCeph imaging software. Statistical analysis was conducted using Python version 3.11.9. (3) Results: Significant correlations were observed between FHR and craniofacial development, particularly regarding hypodivergent growth patterns. In a sample of 94, molar classes showed varying patterns: Class I—33.3% hyperdivergent, 61.5% normodivergent, 33.3% hypodivergent. Class II—50% hyperdivergent, 30.8% normodivergent, 52% hypodivergent. Class III—16.7% hyperdivergent, 7.7% normodivergent, 14.7% hypodivergent. Y-axis to SN angle values were within normal limits across groups (Group I: 65.0 (IQR: 61.2-69.0), Group II: 65.0 (IQR: 62.0-69.0), Group III: 67.0 (IQR: 59.7- 69.0). A strong negative correlation was found between Y-axis to SN angle and Jarabak’s ratio (r = -0.72, p &lt; 0.001), highlighting the need for holistic assessment methods in orthodontic practice. (4) Conclusion: Patients from Timis county predominantly exhibit a hypodivergent growth pattern across all malocclusion types. Understanding these patterns is essential for comprehensive orthodontic treatment planning. Further research is needed to explore the implications of these findings on treatment outcomes and patient care.

Background: Pulmonary sequestration (PS), generally diagnosed using computed tomography pulmonary angiography (CTPA), is a rare congenital developmental malformation of the lung that is characterized by nonfunctional lung tissue independent of the normal lung tissue. This study summarizes the imaging features of the supplying arteries and draining vessels in patients with PS with an aim to assist with timely clinical diagnosis and operation guidance. Materials and Methods: A total of 55 patients with PS diagnosed on CTPA from multiple clinical centers were retrospectively analyzed. Data included demographic characteristics, imaging features, disease location, isolation type, and the features of supplying and draining vessels, as shown on CTPA images. Results: Of the 55 patients reviewed, 3 (5.45%) were children, 3 (5.45%) were adolescents, and 49 (89.09%) were adults, with a mean age of 44 years. Fifty-four (98.18%) patients had intralobar sequestration and one (1.82%) had extralobar sequestration. PS was noted 3.5 times more frequently in the left lower lobe than in the right lower lobe. For the supplying arteries, 47 (85.45%) were derived from the descending thoracic aorta, 1 (1.82%) from the abdominal aorta, 7 (12.73%) from the celiac axis, and 1 (1.82%) from the bronchial artery. The draining vessels were the pulmonary veins in 49 patients (89.09%), the umbilical vein in 1 (1.82%), the venae intercostal in 1 (1.82%), the pulmonary arteries in 11 (20.00%), and not shown on the images in 2 (3.64%). Conclusion: Clinical presentations of PS are non-specific and can be easily missed or misdiagnosed. However, CTPA can help improve the diagnostic accuracy and identify the supplying arteries and draining vessels, which significantly contribute to surgical planning.

X-ray Fluorescence Computed Tomography (XFCT) is an emerging non-invasive imaging technique providing molecular-level data, gaining attention for high-resolution imaging. However, increased sensitivity with benchtop X-ray sources raises radiation exposure. Artificial Intelligence (AI), particularly deep learning (DL), has revolutionized medical imaging by delivering high-quality images in the presence of noise. In XFCT, traditional methods rely on complex algorithms for noise reduction, but AI holds promise in addressing high-dose concerns. We present an optimized SCUNet model for noise reduction in low-concentration XRF images. Compared to higher-dose images, our method’s effectiveness is evaluated. While various denoising techniques exist for X-ray and CT, few address to XFCT. The DL model is trained and assessed using the augmented data, focusing on background noise reduction. Image quality is measured using PSNR and SSIM, comparing outcomes with 100% X-ray dose images. Results show the proposed algorithm achieves high-quality images from low-dose and low-contrast agents, with a maximum PSNR of 39.05 and SSIM of 0.86. The model outperforms BM3D, NLM, DnCNN, and SCUNet in both visual inspection and quantitative analysis, particularly in high-noise scenarios. This indicates the potential of AI, specifically the SCUNet model, in significantly improving XFCT imaging by mitigating the trade-off between sensitivity and radiation exposure.

ABSTRACT Objectives: Typical Diagnostic Reference Levels (DRL) in terms of Computed Tomography Dose Index (CTDI) and patient dose in terms of Effective Dose (ED ) and Size Specific Dose Estimate (SSDE) were estimated in Computed Tomography (CT) guided biopsy procedures. Materials and Methods: A total of 226 CT biopsy procedures - Iliac bone, liver, lung, mediastinum and para-aortic tissue - were retrospectively analyzed and Typical DRL extracted based on ICRP 135 instructions. Results: For helical mode acquisitions, DRLs in terms of CTDIvol were 9.7 mGy for Iliac bone, 8.9 mGy for liver, 8.8 mGy for lung, 7.9 mGy for mediastinal mass and 9 mGy for para-aortic lymph nodes biopsy procedures. For biopsy acquisitions, DRL values were 7.3 mGy, 7.7 mGy, 5.6 mGy, 5.6 mGy and 7.4 mGy respectively. Also, SSDE median values ranged from 7.6 mGy to 10 mGy for biopsy acquisitions and 11,3 mGy to 12,6 mGy for helical acquisitions, as well as the median values for effective dose ranged from 1.6 mSv to 5,7 mSv for biopsy scans and 3.9 to 9.3 mSv for helical scans. Conclusions: The use of DLR as an optimization tool for CT-guided biopsy procedures revealed that helical scans across the entire anatomical region greatly affect radiation dose compared to biopsy acquisitions.

Introduction: maxillary hypoplasia and mandibular asymmetry may be corrected with orthognathic surgery at the completion of growth. Many patients require segmental Le Fort I osteotomies to obtain the most stable results. Unfortunately, if Invisalign is chosen for pre-surgical preparation, ClinCheck © software does not allow for prediction when these complex surgeries are planned. The objective of this paper was to show the potential of aligners beyond its software in most complex cases like multiple-piece maxillary osteotomies in cleft and non-cleft patients. Method: Thirteen patients who underwent pre-surgical treatment with clear aligners-Invisalign (study group) were matched in terms of diagnosis, surgical procedure, and orthodontic complexity with thirteen patients treated using fixed appliances (control group). A technique based on simple superimposition was devised to enhance the software for creating a suitable occlusion for segmental pre-surgical treatments. Virtual curves following the lower arch were employed to guide the correct pre-surgical positions of the upper teeth. The amount of impressions required in both groups to achieve satisfactory pre-surgical alignment of the segmented arches was compared. Results: one or no refinement phase were needed in the Invisalign group to reach an acceptable pre-surgical occlusion while the amount of pre-surgical impressions taken in order to reach adequate coordination with fixed appliance treatment was slightly higher. The average overall treatment duration did not show a statistically significant variation between the groups. Conclusions: it appears that clear aligner could serve as an effective treatment for individuals with skeletal discrepancies, including cleft and craniofacial anomalies, necessitating segmental Le Fort I osteotomies when aided by the suggested superimposition approach during digital pre-surgical movement simulations. More sophisticated softwares will certainly be implemented in the future.

Histone post-translational modification is one of the main mechanisms of epigenetic regulation, which plays a crucial role in the control of gene expression and various biological processes. However, whether or not it affects fungal virulence is not clear in Sclerotinia sclerotiorum. In this study, we identified and cloned the histone methyltransferase Defective in methylation 5 (Dim5) in S. sclerotiorum, which encodes a protein containing a typical SET domain. SsDim5 was found to be dynamically expressed during infection. Knockout experiment demonstrated that deletion of SsDim5 reduced the virulence in Ssdim5-1/Ssdim5-2 mutant strains, accompanied by a significant decrease in H3K9 trimethylation levels. Transcriptomic analysis further revealed the downregulation of genes associated with mycotoxins biosynthesis in SsDim5 deletion mutants. Additionally, the absence of SsDim5 affected the fungus's response to oxidative and osmotic, as well as cellular integrity. Together, our results indicate that the H3K9 methyltransferase SsDim5 is essential for H3K9 trimethylation, which regulating fungal virulence to host plants through impacting on mycotoxins biosynthesis, and the response to environmental stresses in S. sclerotiorum.

Dirofilariosis is an infectious disease caused by species of the Dirofilaria genus. It is manifested by the appearance of a subcutaneous swelling, especially in the eye region. We present the case of a 29-year-old patient that accused facial asymmetry in the right genian region. Following clinical and paraclinical evaluations, the diagnosis of parasitic cyst was established in the context of dirofilariosis with Dirofilaria repens (D. repens). Treatment consisted of surgical excision of the formation associated with prophylactic antibiotic medication. Macroscopic analysis of the excision piece revealed a structure that contains a cystic cavity and a filamentous form with a length of approximately 10 mM and a diameter of 1 mM. This is the first case of dirofilariosis located in the genian region reported in Romania. The overview of this pathology is important to raise awareness among physicians about its presence and its clinical variations.

Any malocclusion can be associated with various face development patterns, including hyper, neutral and hypodivergent growth patterns. We measured face height ratios, angle formed by Y axis to SN and growth patterns in various malocclusions in a group of patients from Timis county. The pretreatment digital cephalograms of 350 participants were split into three groups based on Angle's classification of dentoalveolar malocclusion. Every cephalogram was digitally traced and analyzed using a composite cephalometric method analysis utilizing the WebCeph imaging cephalometric program, which included two linear and one angular. In general, patients from Timis county have a hypodivergent development pattern. Hypodivergent development pattern predominated in group I, II, and III. Group I hyperdivergent 5.14%, normodivergent 16.01%, hypodivergent 78.85%. Group II hyperdivergent 2.78%, normodivergent 14.44%, hypodivergent 82.78%. Group III hyperdivergent 10.53%, normodivergent 10.53%, hypodivergent 78.94%. In all three groups, the value of the angle formed by Y axis to SN is within normal limits group I 65.4 ±4.34°, group II 63.87± 3.86° and group III 64.66 ±5.28°. A strong negative correlation was found between angle: Y axis to SN and facial height ratio (r= -0,766; p &lt;0.001). In all kinds of malocclusion, patients from Timis county show primarily a hypodivergent development pattern.

Breast cancer has become the most diagnosed cancer in women globally with 2.3 million new diagnosis each year. Accurate early staging is essential for improving survival rates with metastatic spread from loco regional to distant metastasis decreasing rates by 50%. Current guidelines do not advice the routine use of Positron Emission Tomography (PET)-Computed Tomography (CT) in staging of early breast cancer in the absence of symptoms. However, there is a growing body of evidence to suggest that PET-CT used in this early stage can benefit the patient by improving staging and as a result treatment and outcome as well as psychological burden without increasing costs to the health service. Ongoing research in PET radiomics and artificial intelligence is showing promising future prospects in its use in diagnosis, staging, prognosticatication and assessing response to treatment in breast cancer. Furthermore ongoing research to address current limitations of PET-CT by improving techniques and tracers is encouraging.

Objective: Polymyalgia rheumatica (PMR) and giant cell arteritis (GCA) are often overlapping conditions. We aimed to determine whether 18F-fluorodeoxyglucose (FDG) positron emission tomography-computed tomography (PET-CT) is useful in identifying PMR in the setting of large vessel vasculitis (LVV)-GCA. Methods: Patients diagnosed with LVV-GCA by PET-CT at a tertiary referral hospital for a population of 450,000 people over a two-year period were reviewed. Scoring was performed based on potential significant FDG uptake at up to 16 sites in nine different extravascular areas (SCORE 16). Differences in extravascular sites of significant FDG uptake were evaluated between LVV-GCA with a clinical diagnosis of PMR or not. Results: Fifty-four patients were diagnosed with LVV-GCA by 18F-FDG-PET-CT. Of them, 21 (38.8%) were clinically diagnosed with PMR. Significant extravascular FDG uptake was more frequently observed in those with a clinical diagnosis of PMR. In this sense, the SCORE 16 was higher in those with clinical PMR (5.10 ± 4.05 versus 1.73 ± 2.31 in those without a clinical diagnosis of PMR; p< 0.001). A SCORE 16 involving more than 4 sites of significant FDG uptake yielded a sensitivity of 52% and a specificity of 91% for establishing a clinical diagnosis of PMR associated with LVV-GCA. The best areas of significant FDG uptake to clinically identify PMR in patients with LVV were the shoulder, the greater trochanter and the lumbar interspinous regions with an area under the ROC curve of 0.810 (0.691-0.930). Conclusion: Significant extravascular 18F-FDG-PET-CT uptake may help establish a clinical diagnosis of PMR in patients with LVV-GCA. These patients are more commonly diagnosed with PMR if they have significant FDG uptake in the shoulder, greater trochanter, and lumbar interspinous areas.

Oncology has emerged as a crucial field of study and treatment in the domain of medicine. Computed tomography has gained widespread adoption as a radiological modality for the identification and characterisation of pathologies, particularly in oncology, enabling precise identification of affected organs and tissues. However, achieving accurate liver segmentation in computed tomography scans remains a challenge due to the presence of artefacts and the varying densities of soft tissues and adjacent organs. This paper compares artificial intelligence algorithms and traditional medical image processing techniques to assist radiologists in liver segmentation on computed tomography scans, and evaluates their accuracy and efficiency. It is noteworthy that although studies have been conducted on liver segmentation in computed tomography scans, they often lack an intuitive and visual component that allows healthcare professionals to manipulate and observe the results obtained, thereby limiting interaction with the outcomes. From the literature review, challenges such as under-segmentation, over-segmentation, and poor boundary detection, as well as the selection of methods to improve the accuracy and efficiency of liver segmentation in computed tomography scanners, are highlighted as needs to be addressed. The importance of future research in understanding the essential features for the study, generating more datasets, improving segmentation efficiency, and developing lightweight artificial intelligence frameworks for liver segmentation is outlined.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Purpose: The aim of this article is to analyze the incidence of undiagnosed obstructive sleep apnea OSA in patients affected by dento-skeletal malformation. We also evaluated the patterns most affected by the condition and calculated the post surgical changes. Methods: We conducted a retrospective cohort study on 71 patients including 35 men and 36 women. Patients were evaluated with Polysomnography before surgery and at least 6 months after surgery to assess any improvement or worsening of the apnea hypopnea index AHI index. Regarding AHI evaluation criteria an AHI > 5 was considered indicative of OSA, 4 5, com-pared to 20.5% described in the Italian population. Conclusion: In patients who receive orthognathic surgery the presence of Obstructive Sleep Apnea is significantly higher than in the general population. When planning the surgical correction of a dentoskeletal malformation, the surgeon must aim not only to the aesthetics results, but also to a proper stomatognathic and respiratory function, this cannot be done without taking poly-somnography information into account.

Fractures of the talar neck and body are associated with spine fractures and scoliosis deformity, which affect cosmetic appearance and cause difficulty in ambulation. The implant design for talus surgery is thriving as a functional alternative in case of severe talar destruction, focusing on segmentation and reconstruction of the talus’s shape. However, manual segmentation of the talus is time-consuming and subjective. In this study we exploited the automatic segmentation framework to efficiently train a deep learning-based model to accurately segment the talus based on computed tomography imaging. We developed three model configurations with nnU-Net and investigated their Dice similarity coefficients (DSC) and 95% Hausdorff distances (HD95) for talus segmentation on a CT image dataset. The three configurations performed well (DSC > 0.95, HD95 < 0.6). When tested on the same samples, one of the configurations was more efficient while ensuring higher accuracy. We propose to focus on talus anatomic variations with increasing age based on this framework and apply it to clinical trials at the next stage.

The ever-growing field of materials with applications in the biomedical field holds great promise regarding the design and fabrication of devices with specific characteristics especially scaffolds with personalized geometry and architecture. The continuous technological development pushes the limits of innovation in obtaining adequate scaffolds and establishing their characteristics and performance. To this end, computed tomography (CT) proved to be a reliable, non-destructive, high-performance machine, enabling visualization and structure analysis at sub-micronic resolutions. CT allows both qualitative and quantitative data of the 3D model, offering an overall image of its specific architectural features as well as reliable numerical data for rigorous analyses. The precise engineering of scaffolds consists in the fabrication of objects with well-defined morphometric parameters (e.g.: shape, porosity, wall thickness), and in their performance validation through thorough control over their behavior (in situ visualization, degradation, new tissue formation, wear, etc.). This review is focused on the use of CT in biomaterial science with the aim of qualitatively and quantitatively assess the scaffolds’ features and in monitoring their behavior following in vivo or in vitro experiments. Furthermore, the paper presents the benefits and limitations regarding the employment of this technique when engineering materials with applications in the biomedical field.

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

The current availability of electronic health records represents an excellent research opportunity on multimorbidity, one of the most relevant public health problems nowadays. However, it also poses a methodological challenge due to the current lack of tools to access, harmonize and reuse research datasets. In FAIR4Health, a European Horizon 2020 project, a workflow to implement the FAIR (Findability, Accessibility, Interoperability, and Reusability) principles on health datasets was developed, as well as two tools aimed at facilitating the transformation of raw datasets into FAIR ones and the preservation of data privacy. As part of this project, we conducted a multicentric retrospective observational study to apply the aforementioned FAIR implementation workflow and tools to five European health datasets for research on multimorbidity. We applied a federated frequent pattern growth association algorithm to identify the most frequent combinations of chronic diseases and their association with mortality risk. We identified several multimorbidity patterns clinically plausible and consistent with the bibliography, some of which were strongly associated with mortality. Our results show the usefulness of the solution developed in FAIR4Health to overcome the difficulties in data management and highlight the importance of implementing a FAIR data policy to accelerate responsible health research.

The increasing use of whole-body computed tomography (WBCT) examinations, also known as panCT, in emergency departments for trauma patients has raised concerns about potential over-use and the associated risk of unnecessary radiation exposure. The purpose of this study was to examine the utilization patterns and findings of panCT scans performed over one year at a major academic hospital. This retrospective cohort study included 599 trauma patients (adults and pe-diatrics) who underwent panCT scans in 2023. De-identified data for each patient, including the radiology report, age, gender, and dose-length product (DLP), were retrieved and reviewed. Ra-diology reports were classified as negative (no acute traumatic injuries) or positive, with posi-tive cases further subclassified based on injury location. Injury severity scores (ISS) were also calculated based on the findings of the radiology reports. Statistical analysis was performed us-ing Python programming language to assess predictors of report findings. Overall, 56% of panCT scans were negative. Logistic regression showed that age significantly impacted the like-lihood of negative findings (p=0.009), while gender did not (p=0.182). One-third of positive cases showed injuries either in head and neck (H&N) or chest-abdomen-pelvis (CAP) regions. Most cases (70% adults, 65% pediatrics) had an ISS between 1 and 8. Median DLP values were 2264 mGy.cm in pediatrics and 2666 mGy.cm in adults. The study showed a high rate of negative panCT scans, suggesting potential overuse of panCT. These findings highlight the need for more selective CT imaging approaches, evidence-based guidelines, and decision-support tools to promote appropriate utilization of panCT scans, reducing unnecessary radiation exposure while ensuring high-risk patients receive appropriate imaging.

Contrast agents developed for X-ray computed tomography (CT) offer extremely valuable tools and techniques in diagnostics via contrast enhancements. Heavy metal-based nanoparticles (NPs) can provide high contrast in CT images. These result from a high density of heavy metal atoms with high X-ray attenuation coefficients that exceed that of iodine (I), which is currently used in hydrophilic organic CT contrast agents. Nontoxicity and colloidal stability are vital characteristics in designing heavy metal-based NPs as CT contrast agents. In addition, the particle size must be small for in vivo renal excretion. In vitro phantom imaging studies can provide X-ray attenuation efficiency, which is a critical parameter for CT contrast agents, and the imaging performance of CT contrast agents can be demonstrated via in vivo experiments. This review focuses on in vitro and in vivo studies of various heavy metal-based NPs (metal: Au, Pt, Pd, Ag, Ce, Gd, Dy, Ho, Yb, Ta, W, and Bi) and provides an outlook on their use as high-performance CT contrast agents.

Early detection improves prognosis in pancreatic ductal adenocarcinoma (PDAC) but is challenging as lesions are often small and poorly defined on contrast-enhanced computed tomography scans (CE-CT). Deep learning can facilitate PDAC diagnosis, however current models still fail to identify small (&lt;2cm) lesions. In this study, state-of-the-art deep learning models were used to develop an automatic framework for PDAC detection, focusing on small lesions. Additionally, the impact of integrating surrounding anatomy was investigated. CE-CT scans from a cohort of 119 pathology-proven PDAC patients and a cohort of 123 patients without PDAC were used to train a nnUnet for automatic lesion detection and segmentation (nnUnet_T). Two additional nnUnets were trained to investigate the impact of anatomy integration: (1) segmenting the pancreas and tumor (nnUnet_TP), (2) segmenting the pancreas, tumor, and multiple surrounding anatomical structures (nnUnet_MS). An external, publicly available test set was used to compare the performance of the three networks. The nnUnet_MS achieved the best performance, with an area under the receiver operating characteristic curve of 0.91 for the whole test set and 0.88 for tumors &lt;2cm, showing that state-of-the-art deep learning can detect small PDAC and benefits from anatomy information.

There is paucity of data in the available medical literature regarding the parameters of volumetric perfusion of pancreas grafts. Materials and methods From February 5, 2016 to December 23, 2021, we performed perfusion computed tomography in 41 patients at different times after simultaneous pancreas and kidney transplantation. The study group consisted of 18 men (44%) and 23 women (56%) with a long history of type 1 diabetes complicated by terminal chronic renal failure. The results of perfusion computed tomography of the pancreas graft were studied, and the effects of post-transplantation timing and graft revascularization peculiarities on volumetric perfusion parameters were evaluated. Results The median arterial blood flow, arterial blood volume, and permeability of the pancreas graft were 115.1 [99.7;130.3] mL/100 mL/min, 46.7 [37.4;56.9] mL/min and 8.6 [4.1;11.4] mL/100 mL/min, respectively. No statistically significant differences in the averaged perfusion values were found in the head, body, and tail of the pancreas graft. The post-transplantation timing and the number of arteries involved in graft revascularization did not have a significant effect on the volumetric perfusion of the graft. Conclusion The volumetric perfusion results of the pancreas graft correspond to those obtained in the study of pancreatic perfusion in healthy participants.

This article aims to detect lung cavitations using lung ultrasound (LUS) in a cohort of patients with pulmonary tuberculosis (TB) and correlate the findings with chest computed tomography (CT) and chest x-ray (CXR) to obtain LUS diagnostic sensitivity. Patients with suspected TB were enrolled after being evaluated with CXR and chest CT. A blinded radiologist performed LUS within 3 days after the admission at the Infectious Diseases Department. Finally, 82 patients were enrolled in the study. BAL confirmed TB in 58/82 (71%). Chest CT showed pulmonary cavitations in 38/82 (43.6%; 32 TB patients and 6 non-TB ones), LUS in 15/82 (18.3%; 11 TB patients and 4 non-TB ones) and CXR in 27/82 (33%; 23 TB patients and 4 non-TB ones). Patients with multiple cavitations were 12 detected at CT and only 1 at LUS. LUS sensitivity was 39.5%, specificity 100%, PPV 100%, NPV 65.7%. CXR sensitivity was 68.4% and specificity 97.8%. No false positive cases were found. LUS sensitivity is rather low as many cavitated consolidations do not reach the pleural surface. Aerated cavitations could be detected with LUS with relative confidence, highlighting a thin air-crescent sign towards the pleural surface within a hypoechoic area of consolidation, easily distinguishable from dynamic or static air-bronchogram.

We aimed to directly compare the cost-effectiveness of the NELSON and NLST screening protocols, two trials influencing lung cancer screening implementation internationally. A decision-analytic model analyzing the cost-effectiveness of the NELSON protocols was manipulated to reflect the protocols of the NLST, while maintaining features specific to the Hungarian healthcare setting. In the NELSON protocol, there are three possible outcomes to the initial round of screening: positive, negative, or indeterminate, indicating an uncertain degree of suspicion for lung cancer. This pro-tocol differs from the NLST protocol, in which the only possible screening outcomes are positive or negative, with no indeterminate option. The NLST pathway for smokers aged 55-74 resulted in a 43 € increase in total average lifetime costs compared to the Hungarian screening pathway and re-sulted in a lifetime gain of 0.006 QALYs. The incremental costs and QALYs yield an ICER of 7875 €/QALY. Our results demonstrate that assigning any suspicious LDCT screen as a positive result (NLST protocol) rather than indeterminate (NELSON protocol) can yield a slight QALY gain that is worth the additional use of resources according to Hungary’s willingness to pay threshold. Our study provides insight on the cost-effectiveness, advantages, and disadvantages of various LDCT screening protocols for lung cancer and can assist other countries as they implement their screening programs.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

Background: Whole-body computed tomography (WBCT) is commonly employed for primary screening in pediatric patients experiencing out-of-hospital cardiac arrest (OHCA) without prehospital return of spontaneous circulation (ROSC). This study aimed to evaluate the cause of OHCA on WBCT and compare WBCT findings between ROSC and non-ROSC groups in non-traumatic pediatric OHCA cases in an emergency department (ED) setting. Methods: A retrospective analysis was conducted on 27 pediatric patients (mean age: 32.4 months; median age: 10 months) who experienced non-traumatic OHCA without prehospital ROSC and were transported to our tertiary care hospital between January 2013 and December 2023. WBCT scans were performed to investigate the cause of OHCA, with recorded findings in the head, chest, abdomen, and subcutaneous tissues. Results: In all cases, the direct causes of OHCA were undetermined, and WBCT identified no fatal findings. Statistical comparisons of CT findings between the ROSC and non-ROSC groups revealed significant differences. The non-ROSC group had a higher incidence of brain swelling, loss of cerebral gray-white matter differentiation, symmetrical lung consolidation/ground-glass opacity, cardiomegaly, hyperdense aortic walls, narrowed aorta, gas in the mediastinum, and hepatomegaly compared to the ROSC group. Conclusions: Although WBCT did not provide the direct cause of OHCA, it clarified several indicative findings for non-ROSC. These imaging findings could support clinical decision-making, offering objective criteria for discontinuing resuscitation in pediatric OHCA cases where prehospital ROSC is absent.

18F-fluorodeoxyglucose positron emission tomography and computed tomography (18F-FDG PET-CT) is increasingly used in the diagnosis, prognosis, staging, and treatment monitoring of many tumor types. However, only a small number of studies have reported the use of 18F-FDG PET-CT in intrahepatic cholangiocarcinoma (ICC). This study aimed to examine the accuracy of tumor staging in ICC by using 18F-FDG PET-CT. Between January 2009 and December 2020, patients with suspected ICC were retrospectively enrolled in the study and underwent imaging. The sensitivity and specificity of 18F-FDG PET-CT, CT, and magnetic resonance imaging (MRI) in detecting tumors, satellite focus, vascular invasion, and lymph node metastases were analyzed. The efficacy of 18F-FDG PET-CT for tumor staging was evaluated. Of the 110 patients who were enrolled in the study, 52 underwent surgical treatment and 45 were histologically diagnosed with ICC. When compared with CT or MRI, 18F-FDG PET-CT had similar sensitivity and specificity values for diagnosing satellite focus and vascular and bile duct invasion; however, PET-CT showed higher accuracy in diagnosing regional lymph node metastases. The accuracy of tumor staging by 18F-FDG PET-CT was higher than that by CT/MRI. Thus, 18FDG PET-CT may support tumor staging in ICC.

Conclusions: HRCT is a valuable tool in preoperative assessment of cholesteatoma, helping in making surgical decisions. It can accurately predict the extent of disease and is helpful for detecting unapparent dangerous situations. However it is not very accurate in detecting Fallopian canal and stapes erosion.

.Purpose: This paper presents a comparative analysis of state-of-the-art DIR algorithms in the context of head and neck squamous cell carcinoma (HNSCC) radiation therapy. Materials and Methods: We used a dataset of head and neck cancer patients within the Cancer Image Archive, which includes 31 patients with 3D CT image data from pre-treatment, mid-treatment, and post-treatment stages of radiotherapy. We applied DIR algorithms to two datasets, one for pre-treatment to mid-treatment registration and another for mid-treatment to post-treatment registration, by aligning one CT image to another CT image. To quantitatively analyze the patient data, we focused on the spinal cord, optic nerve, brain stem, cochlea, and PTV as the OAR datasets. To verify the DIR algorithm, we used two non-learning-based methods, SyN and NiftyReg, as well as three deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph. We trained a deep learning model by adjusting the ratio of the training dataset, validation dataset, and test dataset to 7:1:2. Results: The average DSCs of SyN and NiftyReg, the non-learning-based methods, were 0.74±0.06 and 0.70±0.12, respectively. The deep learning-based methods, Voxelmorph, Cyclemorph, and Transmorph, had average DSCs of 0.72±0.08, 0.68±0.11, and 0.69±0.13, respectively. The deep learning DIR algorithm produced transformed outputs of OAR/PTV in a shorter time than other models, including commercial and conventional mathematical algorithms (At Inference(sec/images), Voxelmorph: 0.36, Cyclemorph: 0.3, Transmorph: 5.1, SyN: 140, NiftyReg: 40.2). Conclusions: In conclusion, our study provides a comprehensive comparison of commercial DIR algorithms with traditional and deep learning-based DIR methods. Our results demonstrate that commercial DIR algorithms outperform traditional DIR methods in terms of accuracy and efficiency. However, we also show that deep learning-based DIR methods have the potential to achieve similar performance to commercial algorithms with proper training and optimization. Our findings suggest that both commercial and deep learning-based DIR methods have their respective advantages and limitations, and the choice of method should depend on the specific requirements of the clinical application. Overall, our study contributes to ongoing efforts to improve the accuracy and efficiency of DIR methods for better patient outcomes.

The flow properties of pellets or granules are crucial for further processing the drug dosage forms. Optimal compression or filling the multiparticulate dosage forms into capsules is influenced by forces between discrete particles, which could be partially characterized by flow properties. Several techniques were developed for the examination of flowability, including static and dynamic methods applying empirical studies and the up-to-date chaos theory; however newest methods seem only to be powerful with the supplement of empirical principles. Our experiments try to refine both the technique of analysis and the methods by finding new, alternative ways. Our approach to the flowability measurements was to set up a dynamic time-dependent model which combines empirical observations and the chaos theory on a geometrical basis, thus find new aspects regarding flow properties of pellets and granules that could be relevant for drug developers.

Background: Multiple system atrophy (MSA) is a rapidly progressive neurodegenerative disorder that has no curative treatment. Diagnosis is based on a set of criteria established by Gilman (1998 and 2008) and recently updated by Wenning (2022). We aim to determine the effectiveness of [123I]Ioflupane SPECT in MSA, especially at the initial clinical suspicion. Methods: Cross-sectional study of patients at initial clinical suspicion of MSA, referred for [123I]Ioflupane SPECT. Results: 139 patients (68 men, 71 women) were included, 104 being MSA-probable and 35 MSA-possible. MRI was normal in 89.2% while SPECT was positive in 78.45%. SPECT showed high sensitivity (82.46%) and positive predictive value (86.24), reaching maximum sensitivity in MSA-P (97.26%). Significant differences were found when relating both SPECT assessments in the healthy-sick and inconclusive-sick groups. We also found an association when relating SPECT to the subtype (MSA-C or MSA-P), as well as to the presence of parkinsonian symptoms. Lateralization of striatal involvement was detected (left side). Conclusions: [123I]Ioflupane SPECT is a useful and reliable tool for diagnosing MSA, with good effectiveness and accuracy. Qualitative assessment shows a clear superiority when distinguishing between the healthy-sick categories, as well as between the parkinsonian (MSA-P) and cerebellar (MSA-C) subtypes at initial clinical suspicion.

Background and purpose: Dynamic 18F-FDG PET-CT scanning can accurately quantify 18F-FDG uptake and has been successfully applied in diagnosing and evaluating therapeutic effects in various malignant tumors. There is no conclusion as to whether it can accurately distinguish benign and malignant lymph nodes in nasopharyngeal cancer. The main purpose of this study is to reveal the diagnostic value of dynamic PET-CT in cervical lymph node metastasis of nasopharyngeal cancer through analysis. Method: We first searched for cervical lymph nodes interested in static PET-CT, measured their SUV-Max values, and found the corresponding lymph nodes in magnetic resonance images before and after treatment. The valid or invalid groups were included according to the changes in lymph node size before and after treatment. Their Ki values were measured on dynamic PET-CT and compared under different conditions. Then, we conducted a correlation analysis between different factors and Ki values. Finally, diagnostic tests were conducted to compare the sensitivity and specificity of Ki and SUV-Max. Result: We included 67 cervical lymph nodes from different regions of 51 nasopharyngeal cancer patients and divided them into valid and invalid groups based on changes before treatment. The valid group includes 50 lymph nodes, while the invalid group includes 17. Significant differences (P<0.001) between the two groups in SUV-Max, Ki-Mean, and Ki-Max values. When the SUV-Max≤4.5, there was no significant difference in the Ki-Mean and Ki-Max between the two groups (P>0.05). When SUV-Max≤4.5 and pre-treatment lymph nodes<1.0cm, the valid group had significantly higher Ki-Mean (0.00910) and Ki-Maximum (0.01004) values than the invalid group (Ki-Mean=0.00716, Ki -Max=0.00767) (P<0.05). When SUV-Max≤4.5, pre-treatment lymph nodes<1.0cm, and EBV DNA replication was normal, Ki-Mean (0.01060) and Ki-Max (0.01149) in the valid group were still significantly higher than the invalid group (Ki-Mean=0.00670, Ki-Max=0.00719) (P<0.05). The correlation analysis between different factors (SUV-Max, T-stage, normal EB virus DNA replication, age, pre-treatment lymph node<1.0cm) and Ki value showed that SUV-Max and pre-treatment lymph node<1.0cm were related to Ki-Mean and Ki-Max. Diagnostic testing was conducted, the AUC value of the SUV-Max value was 0.8259 (95% confidence interval: 0.7296-0.9222), the AUC value of the Ki-Mean was 0.8759 (95% confidence interval: 0.7950-0.9567), and the AUC value of the Ki-Max was 0.8859 (95% confidence interval: 0.8089-0.9629). It was found that the sensitivity of SUV-Max was 88%, the specificity was 76%, the sensitivity of Ki-Mean was 88%, the specificity was 80%, the sensitivity of Ki-Max was 94%, the specificity was 76%, the specificity of Ki-Mean was better than SUV-Max, the sensitivity of Ki-Max was better than SUV-Max. Conclusion: Dynamic PET-CT has shown significant diagnostic value in diagnosing cervical lymph node metastasis of nasopharyngeal cancer, especially for the small SUV value, and lymph nodes do not meet the metastasis criteria before treatment, and EBV DNA replication is normal. Moreover, its sensitivity and accuracy are superior to static PET-CT.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

Before calcification begins, the early embryonic and fetal skeletal development of both mammalian Homo sapiens and the chondrichthyan fish Raja asterias consists exclusively of cartilage. This cartilage is formed and shaped through processes involving tissue segmentation and the frequency, distribution, and orientation of chondrocyte mitoses. In the subsequent developmental phase, mineral deposition in the cartilage matrix conditions the development further. The stiffness and structural layout of the mineralized cartilage have a significant impact on the shape of the anlagen (early formative structures of organs or tissues) and the mechanical properties of the skeletal segments. The fundamental difference between the two studied species lies in how calcified cartilage serves as a scaffold for osteoblasts to deposit bone matrix, which is then remodeled. In contrast, chondrichthyans retain the calcified cartilage as the definitive skeletal structure. This study documents the distinct mineral deposition pattern in the cartilage of the chondrichthyan R. asterias, in which calcification progresses with the formation of focal calcification nuclei or “tesserae”. These are arranged on the flat surface of the endo-skeleton (crustal pattern) or aligned in columns (catenated pattern) in the radials of the appendicular skeleton. This anatomical structure is well adapted to meet the mechanical requirements of locomotion in the water column. Conversely, in terrestrial mammals, endochondral ossification (associated with the remodeling of the calcified matrix) provides limb bones with the necessary stiffness to withstand the strong bending and twisting stresses of terrestrial locomotion. In this study, X-rays of marine mammals (reproduced from previously published studies) document how the endochondral ossification in dolphin’s flipper adapts to the mechanical demands of aquatic locomotion. This adaptation includes the reduction in the length of the stylopodium and zeugopodium and an increase in the number of elements in the autopodium’s central rays.

Current Micro-Computed Tomography (Micro-CT) protocols for microvasculature analysis often necessitate organ dissection and non-clearable contrast agents. We describe a non-destructive technique for achieving high-resolution images of the human coronary microvasculature. Formalin-fixed human hearts were cannulated using venogram catheters designed for balloon occlusion. Catheters were anchored at the aortic root. Hearts were placed in sealable, radiolucent containers filled with insulating polyurethane foam. Iodine potassium iodide (IKI, Lugol's solution;6.3% Potassium Iodide, 4.1% Iodide) was injected into the coronary arteries. Contrast distribution was monitored using a North Star Imaging X3000 Micro-CT scanner with low-radiation settings, followed by high-radiation scans (3600 rad, 60 kV, 900 mA). We successfully imaged two intact human hearts with chronic total coronary occlusions of the right coronary artery. The scans enabled detailed analysis of the vasa vasorum surrounding stenosed and occluded segments. After imaging, both hearts were cleared of iodine and excess polyurethane foam and then returned to their initial formalin-fixed state for indefinite storage. Conclusions: This method allows for the non-destructive, high-resolution micro-CT imaging of coronary microvasculature in intact human hearts, paving the way for 3D microvascular reconstruction in a macrovascular context.

The accurate and timely assessment of lymph node involvement is paramount in the management of patients with malignant tumors, owing to its direct correlation with cancer staging, therapeutic strategy formulation, and prognostication. Dual-energy computed tomography (DECT), as a burgeoning imaging modality, has shown promising results in the diagnosis and prediction of preoperative metastatic lymph nodes in recent years. This article aims to explore the application of DECT in identifying metastatic lymph nodes (LNs) across various cancer types, including but not limited to thyroid carcinoma (focusing on papillary thyroid carcinoma), lung cancer, and colorectal cancer. Through this narrative review, we aim to elucidate the clinical relevance and utility of DECT in the detection and predictive assessment of lymph node metastasis in malignant tumors, thereby contributing to the broader academic discourse in oncologic radiology and diagnostic precision.

Background: Computed tomography examinations have produced high radiation doses to patients, especially the CT brain. This study aimed to optimize the radiation dose and image quality in adult CT brain protocol. Materials and Methods: Images were acquired by Catphan 700 phantom. Radiation doses were recorded as CTDIvol and dose length product (DLP). CT brain protocols were optimized by varying parameters such as kVp, mAs, signal-to-noise ratio (SNR) level, and Clearview iterative reconstruction (IR). Image quality were also evaluataion by The AutoQA Plus software. Results: CT Number accuracy and linearity had a robust positive correlation with the linear attenuation coefficient (µ) and showed more inaccurate CT numbers when using 80 kVp. MTF showed a higher value in 100 and 120 kVp protocols, while high contrast spatial resolution showed a higher value in 80 and 100 kVp protocols. Low contrast detectability and CNR tended to increase when using high mAs, SNR and Clearview IR protocol. Noise decreased when using a high radiation dose and a high percentage of Clearview IR. CTDIvol and DLP were increased with increasing kVp, mAs, and SNR levels, while the increasing percentage of Clearview did not affect the radiation dose. Conclusion: Optimized protocols, including radiation dose and image quality, should be evaluated to preserve diagnostic capability. The recommended parameter settings include kVp set between 100-120 kVp, mAs ranging from 200-300 mAs, SNR level within the range of 0.7-1.0, and an iterative reconstruction value of 30% Clearview to 60% or higher.

In birds, unlike mammals, there is no complete separation between the thoracic and abdominal cavities. Instead, they have the coelomic cavity where most main organs are found. Therefore, an adequate knowledge of the anatomy of the coelomic cavity is of great importance for veterinarians, biologists and the scientific community. This study aimed to evaluate the coelomic cavity anatomy in the Atlantic puffins (Fratercula Arctica) using anatomical sections and computed tomography images.

Image-guided radiotherapy supported by surface guidance can help track lower lung lesion respiratory motion while reducing a patient’s exposure to ionizing radiation. However, it is not always clear how skin respiratory motion magnitudes and correlations with lung lesion respiratory motion vary between different skin regions of interest (ROI). Four-dimensional Computed Tomography (4DCT) images provide information on both skin and lung respiratory motion and are routinely acquired for the purpose of treatment planning in our institution. Analysis of 4DCT images for 57 patients treated in our institution has been conducted to provide information on respiratory motion magnitudes of nine skin ROIs of the torso, a tracking structure (TS) representing lower lung lobe lesion, as well as respiratory motion correlations between nine ROIs and TS. The effects of gender and adipose tissue volume and distribution on these correlations and magnitudes have been analyzed. Significant differences between ROIs in both respiratory motion magnitudes and correlations to TS have been detected. An overall negative correlation between ROI respiratory magnitudes and the adipose tissue has been detected for ROIs with rib cage support. A weak to moderate negative correlation between adipose tissue volume and ROI-to-TS respiratory correlations has been detected for upper thorax ROIs. Respiratory magnitudes in regions without rib support tended to be larger for men than for women, but no differences in ROI-to-TS correlation between sexes have been detected. Described findings should be considered when choosing skin surrogates for lower lung lesion motion management.

Quantification of bone loss for follow-up comparisons has not been routinely performed in patients with parietal thinning so far. This study compares different methodological approaches including both 2- and 3-dimensional methods in computerized tomographies of a single patient. The 2-dimensional method provides accurate measurements of bone thickness, while the 3-dimensional method allows for a more comprehensive view of the bone's structure, including parameters like shape, size, and thickness. The techniques provided valuable data for the treating physician and suggest a possible effect of corticosteroids in this individual patient. The study concludes that 3-dimensional reconstruction of computerized tomographies with subsequent 2-dimensional analyses appears justified for routine radiological practice to increase clinical awareness of the size of the parietal bone defects and allow for quantification of bone loss during long-term follow-ups. Further validation of the proposed analytical approaches is warranted in larger studies to investigate patterns of bone thinning across the skull and changes in bone volumes over time, with specialized software to be approved for such analyses.

This study aims to evaluate the patient’s dose exposure from Computed Tomography Pulmonary Angiography (CTPA) examination and to estimates the cancer risk induced from the examinations based on the patient’s size. One hundred patients were recruited, and data information was collected retrospectively. A multi-detector (MDCT) (Philips Brilliance 128, USA) scanner were utilized for the CTPA examination, and dose data were obtained from the system. The effective diameter of each subjects’ image was measured for the Size-specific dose estimates (SSDEs). All subjects divided into Group 1 (19 – 25 cm), Group 2 (25-28 cm) and Group 3 (28-38 cm), where the association between gender were analysed. Effective dose (E), SSDE, organ dose and cancer risk of each group were evaluated and compared statistically using independent t-test and one-way ANOVA. The range of mean CTDI_vol, DLP and E values were (6.44 – 17.42 mGy), (239 – 631 mGy), (5.19 – 13.90 mSv), respectively. In respective with the patient’s effective diameter, the mean SSDE value for Group 1, Group 2 and Group 3 were 9.93 ± 3.89 mGy, 13.70 ± 9.04 mGy and 22.29 ± 7.35 mGy. The organ dose and cancer risk attained for breast, lung and liver were 17.05 ± 10.40 mGy (194 per one million procedure), 17.55 ± 10.86 mGy (192 per one million procedure) and 15.04 ± 9.75 mGy (53 per one million procedure), respectively. Lung and breast with more massive patient’s effective diameter received the highest dose exposure which increases the probability of the cancer risk. CTDI_vol was found to be underestimated, and SSDE provides more accurate in describing the radiation dose and cancer risk. Body effective diameter found to be significant on the estimation except for gender. Therefore, it is essential to apply optimised protocols in order to reduce patient’s exposure during CTPA examination.

Electrocardigraphy remains as a first-line evaluation method for cardiac function, recording the electrical activity of the heart from the body surface. Since atrial activation is seen on the ECG as P-wave, several factors are known to impact the appearance of the P-wave, such as direction of electric impulse, conduction abnormalities and anatomical characteristics of the atria. The aim of this retrospective study was to find statistically significant associations between anatomy of pulmonary veins (PVs) osberved in cardiac computed tomography (CT) and P-wave appearance during sinus rhythm on resting ECG. For each patient, a resting 12-lead ECG was recorded, the field of analysis was P wave – its’ duration, morphology and axis. The evaluation of the CT scan recordings was performed by creating 3D models of the left atrium and analyzing anatomy of the PVs and left atrial appendage (LAA). Noteworthy correlations were found: anatomy of the left PVs showed an association with LAA volume, LAA morphology and P-wave notching in lead II. The right PVs demonstrated relation with P wave axis and amplitude. Although these correlations cannot be classified as strong, they may play a role in significant scientific discoveries in future research projects.

The morphological aspects of urban growth on wetlands in Africa are under-researched. Using the Densu Delta Ramsar site in Accra, Ghana, as a case study, this paper analyses the morphological patterns and drivers of urban growth and its impact on wetlands. Data were obtained through remote-sensing, ground truthing and limited key informant interviews. The analysis combined land use/land cover, building coverage and multiple regression techniques, with the aid of GIS and STATA software. The findings reveal that urban growth at the Ramsar site follows discernible spatial patterns consistent with the spreading pancake, village magnet and ribbon development models. However, the primary force behind these patterns is growing demand for land to meet housing needs, aided by the failure of state institutions to perform their land use control and wetland protection functions. To achieve sustainable urban development, there is an urgent need to ensure effective wetland management by enforcing existing land use, development control and wetland protection measures. This calls for the strengthening, resourcing and closer collaboration between the various state agencies responsible for urban planning and wetland management. There is also the need to engage and sensitise political leaders to increase their commitment to implementing wetland protection and pro-environmental policies.

Polyetheretherketone (PEEK) in the last few years emerged as an exceedingly promising material for craniofacial defect, due to its biocompatibility and mechanical properties. However, its utilization remains controversial due to its inertness and low osteoinductivity. This study aimed to investigate the postoperative outcomes of patients undergoing maxillo-facial and neurosurgical procedures with PEEK implants. The focus is on evaluating bone regrowth on the surface and edges of the implant, periosteal reactions, and implant positioning. A retrospective analysis of 12 maxillo-facial surgery patients and 10 neurosurgery patients who received PEEK implants was conducted. CT scans performed at least one-year post-operation, were examined for bone regrowth, periosteal reactions, and implant positioning. In maxillo-facial cases, the analysis included mandibular angle and fronto-orbital reconstruction, while neurosurgical cases involved cranioplasty. In maxillofacial surgery, 11 out of 12 patients showed radiological evidence of bone regrowth around PEEK implants, with favorable outcomes observed in craniofacial reconstruction. In neurosurgery, 9 out of 10 patients exhibited minimal or none bone regrowth, while one case demonstrated notable bone regeneration beneath the PEEK implant interface. The study highlights the importance of implant design and patient-specific factors in achieving successful outcomes, providing valuable insights for future implant-based procedures.

Background and Objectives: Mechanical and biological complications can lead to system fracture or screw loss on dental implants. Narrow and regular platforms have been used without a consensus about the effect of distance the abutment from the prosthetic platform margin. The aim of this study is to evaluate different insertion torques in the deformation of tri-channel platform connections through two- and three-dimensional measurements with micro-CT. Materials and Methods: 164 implants were divided into groups (platform diameter and type): 3.5, 3.75, and 4.3 mm NP (Narrow Platform), and 4.3 mm RP (Regular Platform). Each implant-platform group was then divided into four subgroups (n = 10) with different torques: T45 (45 Ncm), T80 (80 Ncm), T120 (120 Ncm) and T150 (150 Ncm). The implant-abutment-screw assemblies were scanned and the images obtained were analyzed. Results: A significant difference was observed for the linear and volume measures between the different platforms (p &lt;0.01) and the different implant insertion torques (p &lt;0.01). Qualitative analysis suggested higher deformation resistance for the 3.75 NP compared to the 3.5 NP, and RP was more resistant compared to the NP. Conclusions: The 0.25-mm increment in the implant platform did not increase the resistance to the applied insertion torques; the 4.3-mm implant was significantly stronger compared to the 3.5-mm implant and the proposed micro-CT analysis was considered valid for both 2D and 3D analyses of micro gaps, qualitatively and quantitatively.

The Coronavirus disease (COVID-19) caused by a novel coronavirus, SARS-CoV-2, has been declared as a global pandemic. Due to its infection rate and severity, it has emerged as one of the major global threats of the current generation. To support the current combat against the disease, this research aims to propose a Machine Learning based pipeline to detect the COVID-19 infection using the lung Computed Tomography scan images (CTI). This implemented pipeline consists of a number of sub-procedures ranging from segmenting the COVID-19 infection to classifying the segmented regions. The initial part of the pipeline implements the segmentation of the COVID-19 affected CTI using Social-Group-Optimization and Kapur’s Entropy thresholding, followed by k-means clustering and morphology-based segmentation. The next part of the pipeline implements feature extraction, selection and fusion to classify the infection. PCA based serial fusion technique is used in fusing the features and the fused feature vector is then employed to train, test and validate four different classifiers namely Random Forest, k-Nearest Neighbors (KNN), Support Vector Machine with Radial Basis Function, and Decision Tree. Experimental results using benchmark datasets show a high accuracy (> 91%) for the morphology-based segmentation task and for the classification task the KNN offers the highest accuracy among the compared classifiers (> 87%). However, this should be noted that this method still awaits clinical validation, and therefore should not be used to clinically diagnose the ongoing COVID-19 infection.

Neutron computed tomography (nCT) has been established at many major neutron sources worldwide, using high-end equipment requiring major investment and development. Many older and smaller reactors would be capable of doing nCT as well, but cannot afford the investment before feasibility is proven. We have developed a compact low-cost but high-quality detection system using a new cooled CMOS camera that can either be fully integrated into a sophisticated setup, or used with a rudimentary CT control and motion system to quickly evaluate feasibility of neutron CT at a given beam line facility. Exchanging the scintillation screen makes it feasible for X-rays as well, even for visible light (and transparent samples) using a matte screen. The control system uses a hack to combine motion control with existing imaging software so it can be used to test several dozen different cameras without writing specific drivers. Freeware software can do reconstruction and 3D imaging.

ST-elevation myocardial infarction (STEMI) remains one of the leading causes of morbidity and mortality worldwide. The identification of novel metabolic and imaging biomarkers could unveil key pathophysiological mechanisms at the molecular level and promote personalized care in patients with acute coronary syndromes. We studied 38 patients with STEMI who underwent primary percutaneous coronary intervention and thrombus aspiration. We sought to correlate serum ceramide levels with micro-CT quantified aspirated thrombus volume and relevant angiographic outcomes, including modified TIMI thrombus grade and pre- or post-procedural TIMI flow. Higher ceramide C16:0 levels were significantly, but weakly correlated with larger aspirated thrombus volume (Spearman r=0.326, p=0.046), larger intracoronary thrombus burden (Nagelkerke R2=0.236, p=0.030) and worse pre- and post-procedural TIMI flow (Nagelkerke R2=0.210; p=0.049 and Nagelkerke R2=0.277; p=0.039, respectively). Ceramides C24:0 and C24:1 were also significantly associated with larger intracoronary thrombus burden (Nagelkerke R2=0.311; p=0.008 and Nagelkerke R2=0.423; p=0.001, respectively). In conclusion, serum ceramide levels (mainly C16:0 and C24:1) were higher among patients with larger intracoronary and aspirated thrombus burden. This suggests that quantification of serum ceramides might improve risk-stratification of patients with STEMI and facilitate a more individualized approach in everyday clinical practice.

This paper presents a script that classify spatial patterns of residential urban growth using a morpho-structural approach. The script performs a combination of variography analysis and morphological closings over buildings possessing a residential function in 2002 and 2017 within a region located in southern France named Centre-Var. The different bounding regions then allow classifying new residential buildings into different categories according to their degrees of clustering/scattering and to their locations regarding existing urban areas. Preliminary results show that this protocol is able to provide useful insights regarding the degree of contribution of each new residential building to different patterns of urban growth (clustered infill, scattered infill, clustered edge-expansion, scattered edge-expansion, clustered leapfrog and scattered leapfrog). Open-access to the script and to the test region data is provided.

The aim of the present study was to predict the response of non-small cell lung cancer (NSCLC) patients to immune checkpoint inhibitors (ICIs) by leveraging computed tomography (CT) images using deep learning techniques. Retrospectively, 624 sequential CT images were gathered from 156 patients at Jiangsu Province Hospital, along with their clinical data. The dataset was subsequently partitioned into three groups: training (n=547), validation (n=64), and test (n=64). Moreover, an external validation cohort included 37 CT images from patients at Nanjing Pukou Peoples' Hospital, accompanied by comprehensive clinical data. An advanced Video Vision Transformer (ViViT) model incorporating global self-attention was utilized to analyse patients treated with ICIs and predict their response. The ViViT model's efficacy was evaluated using a confusion matrix and a receiver operating characteristic curve (ROC). Notably, the ViViT model demonstrated predictive prowess for ICIs response, yielding respective areas under the receiver operating characteristic curve (AUC) of 0.74 (95% CI: 0.69-0.78), 0.74 (95% CI: 0.61-0.86), 0.76 (95% CI: 0.62-0.88), and 0.69 (95% CI: 0.5-0.87) in the training, validation, test, and external validation cohorts. The present study illustrates how a deep learning model can provide a non-invasive means to predict clinical outcomes in NSCLC patients undergoing ICIs, potentially transforming personalized treatment approaches for individuals with NSCLC.

The aim of the study was to compare the standard baseline imaging, with extended radiological staging. To assess our hypothesis, we performed a prospective, single-centre study which included 132 participants recruited between October 2015 and March 2020. Descriptive statistics, the Friedman and chi-squared tests were performed and p &lt; 0.05 was considered significant. Patients were grouped into two cohorts, CT scan cohort (n=87) and PET-CT cohort (n=43). In the first group the originally determined disease stage changed in 36.8 % of cases, in second group in 51.2 %. The consistency between assessment of axillary lymph nodes by imaging (cN) and the postoperative pathology report (pN) was evaluated. In most cases, clinical and pathological evaluation of involved nodes was consistent, for CT scan the result was χ2(1) = 18.98; p &lt; 0.001, for PET-CT the result was χ2(1) = 6.41; p = 0.03. Highly customized radiation therapy defined as dose boost within the involved lymph nodes, not covered by surgeon, was applied in nine patients.

The ability to express and recognize emotion via facial expressions is well known to change with age. The present study investigated the differences in the facial recognition and facial expression of the elderly (n = 57) and the young (n = 115) and measure how each group uses different facial muscles for each emotion with Facial Action Coding System (FACS). In facial recognition task, the elderly did not recognize facial expressions better than young people and reported stronger feelings of fear and sad from photographs. In making facial expression task, the elderly rated all their facial expressions as stronger than the younger, but in fact, they expressed strong expressions in fear and anger. Furthermore, the elderly used more muscles in the lower face when making facial expressions than younger people. These results help to understand better how the facial recognition and expression of the elderly change, and show that the elderly do not effectively execute the top-down processing concerning facial expression.

Synchrotron radiation computed tomography (SRCT) allows more accurate calcified plaque and coronary stenosis assessment as a result of its superior spatial resolution, however, typical micro-computed tomography (micro-CT) systems have even higher resolution. The purpose of this study was to compare performance of high-resolution micro-CT with SRCT in the assessment of calcified plaques and a previously published dataset of coronary stenosis assessment. This experimental study involved micro-CT scanning of three-dimensional printed coronary artery models with calcification in situ used in our previously published SRCT study on coronary stenosis assessment. Measurements of coronary stenosis utilizing both modalities were compared using a paired sample t-test. The degrees of stenosis measured on all but one micro-CT dataset were statistically significantly lower than the corresponding SRCT measurements reported in our previous paper (p&lt;0.0005-0.05). This indicates that the superior spatial resolution of micro-CT was able to further reduce over-estimation of stenosis caused by extensive calcification of coronary arteries and hence false positive results. This study shows that high-resolution micro-CT outperforms SRCT in both calcified plaque and coronary stenosis assessment. This finding will become clinically important for cardiovascular event prediction and enable reclassification of individuals with low and intermediate risk into appropriate risk categories when the technical challenges of micro-CT in clinical practice such as the small field of view and demanding on image processing power are addressed.

Matrices and their inverses allow accurate calculations to be produced quickly and compactly and can be used to control any process represented by a system of equations. Singular matrices require extensive workarounds (costing time and money) to solve these systems of equations because they have no inverse. Finding their inverse involves division by zero. Nevertheless, recently a new number set called semi-structured complex numbers was developed to enable division by zero in algebraic equations. The aim of this research was to demonstrate that the inverse of a singular matrix can be found using semi-structured complex numbers. This research reveals (1) Singular matrices and their inverses can be used to find a unique solution to a pair of simultaneous equations that appear to have infinitely many solutions or appear to have no solution; (2) Singular matrices map coordinates in projective space to coordinates in Euclidean space and their inverse maps coordinates in Euclidean space to coordinates in projective space; (3) the inverse of a singular matrix proves that parallel lines in Euclidean space do not intersect but in projective space intersect at a “point at infinity” and (4) collinear lines that intersect at infinitely many points in Euclidean space only intersect at one point in projective space.

The existing PDC(Polycrystalline Diamond Compacts) -cone hybrid bit bearing adopts a unilateral support structure, which is prone to stress concentration in the journal area, resulting in fracture and wear failure of the bearing, thus reducing the service life of the hybrid bit. In this paper, a new type of double supported bearing hybrid bit is proposed. The static strength analysis of unilateral and bilateral support bearing structures is carried out by finite element simulation, and the stress and strain distribution of the two structures under the load of 20KN-100KN is obtained. Experimental devices for unilateral and bilateral support bearing structures are designed and manufactured to complete 50KN-100KN static pressure loading experiments. The results showed that the stress and strain of unilateral and bilateral support bearing increased linearly with the increase of load. Compared with unilateral bearing, when the load was 100KN, the maximum Mises stress of bilateral bearing decreased from 358.80MPa to 211.10MPa, with a decrease of 41.16%. The maximum contact stress decreased from 415.20MPa to 378.10MPa, decreased by 8.94%, and the maximum principal strain decreased from 11.01e-4 to 9.71e-4, decreased by 11.81%. The axial strain in the danger zone was reduced by 14.68% and 17.35%, respectively. It is found that the contact stress of the simulation data is highly correlated with the bearing life, and the service life of the bilateral bearing bit is increased by 8.94%. The simulation data and experimental results provide data support for the production of hybrid bits with bilateral bearing support.

Germanium films were grown on c-plane sapphire with a 10 nm AlAs buffer layer using molecular beam epitaxy. The effects of Ge film thickness on the surface morphology and crystal structure were investigated by ex-situ characterization techniques. The nucleation of Ge proceeds by forming (111) oriented three-dimensional islands with two rotational twin domains about the growth axis. The boundaries between the twin grains are the origin of 0.2% strain and tilt grains. The transition to a single-grain orientation reduces the strain and results in a better-quality Ge buffer. Understanding the role of thickness on material quality during the Ge(111)/Al2O3(0001) epitaxy is vital for achieving device quality when using group IV material on the sapphire platform.

Objective: To evaluate two different DECT postprocessing protocols for detection of MSU deposits in foot tendons of cadavers with verification by polarizing light microscopy as gold standard.Material and Methods: A total of 40 embalmed cadavers (15 male; 25 female; median age, 82 years; mean, 80 years; range, 52 - 99; SD ± 10.9) underwent DECT to assess MSU deposits in foot tendons.Two postprocessing DECT protocols with different Hounsfield unit (HU) thresholds 150/500 (=established) versus 120/500 (= modified) HU were applied to dual source acquisition with 80 kV for tube A and 140 kV for tube B.Six fresh cadavers (4 male; 2 female; median age, 78; mean, 78,5; range 61 - 95 ) were examined by DECT. Tendon dissection of 2/6 fresh cadavers with positive DECT 120 and negative DECT 150 studies were used to verify MSU deposits by polarizing light microscopy.Results: The tibialis anterior tendon was found positive in 57.5%/100% (DECT 150/120), peroneus tendon in 35%/100%, achilles tendon in 25%/90%, flexor halluces longus tendon in 10%/100%, and tibialis posterior tendon in 12.5%/97.5%. DECT 120 resulted in increased tendon MSU deposit detection, when DECT 150 was negative, with an overall agreement between DECT 150 and DECT 120 of 80 % (P = 0.013). Polarizing light microscope confirmed MSU deposits detected only by DECT 120 in tibialis anterior, achilles, flexor halluces longus and peroneal tendons.Conclusion: The DECT 120 protocol showed a higher sensitivity when compared to DECT 150.

This paper analyses the evolution of the internal damage in two types of steel that show different fracture behaviours, with one of them being the initial material used for manufacturing prestressing steel wires, which shows a flat fracture surface perpendicular to the loading direction, and the other one being a standard steel used in reinforced concrete structures, which shows the typical cup-cone surface. 3mm-diameter cylindrical specimens are tested with a tensile test carried out in several loading stages and, after each of them, unloaded and analysed with X-ray tomography, which allows detection of internal damage throughout the tensile test. In the steel used for reinforcement, damage is developed progressively in the whole specimen, as predicted by Gurson-type models, while in the steel used for manufacturing prestressing steel-wire damage is developed only in the very last part of the test. In addition to the experimental study, a numerical analysis is carried out by means of the finite element method by using a Gurson model to reproduce the material behaviour.

Lung cancer (LC) stands as the foremost cause of cancer-related fatality rates worldwide. Early diagnosis significantly enhances patient survival rate. Nowadays, low dose computed tomography (LDCT) is widely employed on chest as a tool for large-scale lung cancer screening. Nonetheless, a large amount of chest radiographs causes an onerous burden on radiologists. Some computer-aided diagnostic (CAD) tools can provide insights to medical images for diagnosis and augmenting diagnostic speed. However, due to variation in parameter settings across different patients, substantial discrepancies in image voxels persist. We find different voxel-size causing a compromise between model generalization and diagnostic efficacy. This study investigates the performance disparities of diagnostic models trained on original images and LDCT images reconstructed to different voxel-sizes but isotropic. The application is to differentiate a nodule to be benign or malignant. Using 11 features, a support vector machine (SVM) is trained on LDCT images with an isotropic voxel having side-length of 1.5 mm for 225 patients in house. The result yields a favorable model performance with an accuracy of 0.9596 and an area under the receiver operating characteristic curve (ROC/AUC) of 0.9855. In addition to furnish CAD tools for clinical applications, future research is encouraged to include LDCT images from multi-centers.

This study investigates the efficiency of BEAM (Biologically Enhanced Agriculture Management) inoculant, derived from compost produced under Dr. David Johnson-Su's composting technique, in promoting plant growth. A winter mix of pasture comprising Oats, Tetila, unhulled Couch, and Haifa was used as the test crop. Seeds were soaked in BEAM inoculant, water (control), and a competitor product 'Companion.' Results revealed significant enhancements in germination rates, foliage growth, and root development in the BEAM-treated group compared to controls. Further research aims to identify the microbial components of BEAM and explore its potential as a suppressant for fusarium species in orchards.

Unlike electron microscopy, which can achieve very high resolutions, but to date can only be used to study static structures, time-resolved X-ray diffraction from contracting muscles can, in principle, be used to follow the molecular movements involved in force generation on a millisecond timescale albeit at moderate resolution. However, previous X-ray diffraction studies of resting muscles have come up with structures for the head arrangements in resting myosin filaments that are different from the apparently ubiquitous interacting heads motif (IHM) found by single particle analysis of electron micrographs of isolated myosin filaments from a variety of muscle types. This head organization is supposed to represent the super-relaxed state of the myosin filaments where ATP usage is minimized. Here we have tested whether the interacting heads motif structures will satisfactorily explain the observed low-angle X-ray diffraction patterns from resting vertebrate (bony fish) and invertebrate (insect flight) muscles. We find that the interacting heads motif does not, in fact, explain what is observed. Previous X-ray models fit the observations much better. We conclude that the X-ray diffraction evidence has been well interpreted in the past and that there is more than one ordered myosin head state in resting muscle. There is, therefore, no reason to question some of the previous X-ray diffraction results on myosin filaments; time-resolved X-ray diffraction should be a reliable way to follow crossbridge action in active muscle and may be one of the few ways to follow molecular changes in myosin heads on a millisecond timescale as force is actually produced.

Prostate-specific membrane antigen (PSMA) is a well validated prostate cancer marker, but reported PSMA-targeted tracers derived from the Lys-urea-Glu pharmacophore including the clinically validated [99mTc]Tc-EDDA/HYNIC-iPSMA have high off-target uptake in kidneys, spleen and salivary glands. In this study, we synthesized and evaluated three novel 99mTc-labeled PSMA-targeted tracers and investigated if the tracers derived from the Lys-urea-Aad pharmacophore could have minimized uptake in off-target organs/tissues. In vitro competition binding assays showed that compared with HYNIC-iPSMA, the three novel ligands had slightly weaker PSMA binding affinity (average Ki = 3.11 vs 8.96 - 11.6 nM). Imaging and ex vivo biodistribution studies in LNCaP tumor-bearing mice showed that [99mTc]Tc-EDDA/HYNIC-iPSMA and the three novel tracers successfully visualized LNCaP tumor xenografts in SPECT images and were excreted mainly via the renal pathway. The average tumor uptake at 1 h post-injection varied from 5.40 to 18.8 %ID/g, and the tracers derived from the Lys-urea-Aad pharmacophore had much lower uptake in spleen and salivary glands. Compared with the clinical tracer [99mTc]Tc-EDDA/HYNIC-iPSMA, the Lys-urea-Aad derived [99mTc]Tc-EDDA-KL01127 had lower background uptake and superior tumor-to-background contrast ratios, and is therefore promising for clinical translation to detect prostate cancer lesions with SPECT.

Coronary artery disease (CAD) represents a modern pandemic associated with significant morbidity and mortality. The multi-faceted pathogenesis of this entity has long been investigated, highlighting the contribution of systemic factors such as hyperlipidemia and hypertension. Nevertheless, recent research has drawn light to the importance of geometrical features of coronary vasculature on the complexity and vulnerability of coronary atherosclerosis. Various parameters have been investigated so far, including vessel-length, cross-sectional area, curvature, and tortuosity, using primarily invasive angiography and recently non-invasive cardiac computed tomography angiography (CCTA). It is clear that there is correlation between geometrical parameters and both the haemodynamic alterations augmenting the atherosclerosis-prone environment and the extent of plaque burden. The purpose of this review is to discuss the currently available literature regarding this issue and propose a potential non-invasive imaging biomarker, the geometric risk score, which could be of importance to allow early detection of individuals at increased risk of developing CAD.

Since its post-World War II inception, the science of record linkage has grown exponentially and is used across industrial, governmental, and academic agencies. The academic fields that rely on record linkage are diverse, ranging from history to public health to demography. In this paper, we introduce the different types of data linkage and give a historical context to their development. We then introduce the three types of underlying models for probabilistic record linkage: Fellegi-Sunter based methods, machine learning methods, and Bayesian methods. Practical considerations such as data standardization and privacy concerns are then discussed. Finally, recommendations are given for organizations developing or maintaining record linkage programs, with an emphasis on organizations measuring long-term complications of disasters such as 9/11.

Objective: There are currently no known treatment methods for ensuring complete recovery from facial nerve damage. Thus, various basic and clinical studies continue to be conducted to achieve this end. As part of this research, autophagy is being investigated for its role in nerve regeneration. Here, we review the existing literature regarding the involvement and signifi-cance of autophagy in facial nerve injury and regeneration. Methods: A comprehensive litera-ture review was conducted to assess the induction and role of autophagy in facial nerve injury and subsequent regeneration. Results: Studies conducted on rats and mice have demonstrated activation of autophagy and expression of related factors in facial and sciatic nerves. Among the most studied of these factors in relation to degeneration and regeneration of facial and sciatic nerves are LC3II/I, PI3K, mTOR, Beclin-1, ATG3, ATG5, ATG7, ATG9, and ATG12. Conclusion: This analysis indicates that autophagy is involved in the process of nerve regeneration follow-ing facial and sciatic nerve damage. Inadequate autophagy induction or failure of autophagy re-sponses can result in regeneration issues after facial or sciatic nerve damage. Animal studies suggest that autophagy plays an important role in facial and sciatic nerve degeneration and re-generation.

The complex adaptive systems (CAS) research study investigates into the theoretical link of a sustained economic growth as a critical pathway to lift people out of poverty and improve their quality of life. The results show a left-skewed global behavior of an economy-driven human development of 189 countries with 20% or 27 countries obtaining low human development; 80% or 162 countries obtaining medium to very high human development of which 21.16% or 39 countries with medium HDI, 53 or 28.04% or 53 countries with high HDI, and 31.22% or 59 countries with very high HDI. Using the Log (GDP) for visual transformation, closer investigation into the scatterplot diagram reveals that there are also bimodal patterns where countries in the high amplitude and low amplitude groups obtained different human development outcomes despite less or more on economic growth variances mirror on the government policy priorities resulting in four differentiating conditions. Very few countries experience virtuous cycles where both growth and human development are successful; few countries with vicious cycles where both are weak; and many countries with lopsided conditions where the economy is strong but human development is weak, or conversely ones where human development is strong but the economy is weak. The global pattern of economy and human development illustrated by an upward sinusoid or sine wave refutes the conventional linear approach. Uniquely and most importantly, the sinusoidal wave illustrates a decreasing amplitude and decreasing periods as countries manifest apparently complex behaviors that emerge as a result of often nonlinear spatio-temporal interactions among a large number of component systems at different levels of organizations and governments leading to an emergence of a behavior characterizing of a complex adaptive system.

The hepatic sinusoids are lined by thin endothelium containing transcellular pores dubbed fenestra. These fenestrations are completely open channels connecting the sinusoidal lumen to the underlying Space of Disse (SoD) and the hepatocytes of the liver parenchyma. The fenestrations are in the size range 0.05-0.35µm in diameter and cover between 5-15% of the sinusoidal endothelial surface area depending on their location along the sinusoids. Motivation/Research Question: So far, the narrowness of the sinusoids prevented the direct measurement of hemodynamic features such as sinusoidal pressure and flow velocity. A better understanding of these parameters might help in better understanding the physiology of the hepatic niche and possible implications in liver diseases. Few simulations of liver blood flow focus on the level of the individual sinusoid, fewer still include the transcellular pores (fenestrations) of the sinusoidal endothelium, and none have included i) a porosity gradient along the sinusoid wall modelled with through-all pores rather than a porus medium, ii) the presence of the Space of Disse, iii) lymphatic drainage. Model: Computed fluid dynamic (CFD) simulations performed using a numerical model with relevant anatomical characteristics (length, diameter, porous size and porosity). Boundary conditions included physiological/pathological values of inlet/outlet pressure and lymphatic outflow from the portal region of the SoD. Results: The pressure and flow velocity of the sinusoidal lumen was entirely dependent on the shape, i.e. constant versus divergent radius and not dependent on porosity in the sinusoidal wall. The velocity through the space of Disse (SoD) was affected by the addition of lymphatic drainage and increases in porosity in the pericentral area of the model. Variations in porosity also affected flow velocity through the fenestrations. Conclusions: The flow velocity in the SoD was modified by differences in porosity, while the flow velocity in the lumen of the sinusoids was unaffected, even by the absence of fenestrations. The overall shape of the vessel is the singular most important factor in the pressure flow behavior of the sinusoidal lumen. The flow rate over the hepatocytes is the flow rate through the SoD, and is modestly affected by the distribution of porosity along the sinusoid, and by the addition of a lymphatic drainage, this parameter would be of interest for modelling blood exchange with the hepatic parenchyma, especially if accounting for zonation.

Despite various interventions in road safety work, fatal and severe road traffic accidents (RTAs) remain a significant challenge leading to human suffering and economic costs. Understanding the multicausal nature of RTAs, where multiple conditions and factors interact, is crucial for developing effective prevention measures in road safety work. This study investigates the multivariate statistical analysis of co-occurring conditions in RTAs, focusing on single-vehicle accidents with single occupancy and personal injury on Austrian roads outside built-up areas from 2012 to 2019. The aim is to detect recurring combinations of accident-related variables, referred to as blackpatterns (BPs), using the Austrian RTA database. The study proposes Fisher’s exact test to estimate the relationship between an accident-related variable and fatal and severe RTAs (severe casualties). In terms of pattern recognition, the study develops the maximum combination value (MCV) of accident-related variables, a procedure to search through all possible combinations of variables to find the one that has the highest frequency. The accident investigation proceeds with the application of pattern recognition methods, including binomial logistic regression and a newly developed method, the PATTERMAX-method, created to accurately detect and analyse variable-specific BPs in RTA data. Findings indicate significant BPs contributing to severe accidents. The combination of binomial logistic regression and the PATTERMAX-method appears to be a promising approach to investigate severe accidents, providing both insights into detailed variable combinations and their impact on accident severity.

Abstract Tetraspanin CD63 is a cluster of cell surface proteins with four transmembrane domains which associates with tetraspanin-enriched microdomains and typically localizes to late endosomes and lysosomes. CD63 plays an important role in cellular trafficking of different proteins, EV cargo sorting and vesicles formation. We have preciously shown that CD63 is important in LMP1 trafficking to EVs and this also affects LMP1 mediated intracellular signaling including MAPK/ERK, NF-κB and mTOR activation. Using the BioID combined with mass spectrometry, we sought to define the broad CD63 interactome and how LMP1 modulates this network of interacting proteins. We identified a total of 1600 total proteins as proximal interacting newtwork of proteins to CD63. Biological process enrichment analysis revealed significant involvement in signal transduction, cell communication, protein metabolism and transportation. The CD63 only interactome was enriched in Rab GTPases, SNARE proteins and sorting nexins while adding LMP1 into the interactome increased presence of signaling and ribosomal proteins. Our results showed that LMP1 alters the CD63 interactome, shifting the network of proteins enrichment from protein localization and vesicle mediated transportation to metabolic processes and translation. We also show that LMP1 interacts with mTor, Nedd4L and PP2A indicating formation of a multiprotein complex with CD63 thereby potentially regulating LMP1 dependent mTor signaling. Collectively, the comprehensive analysis of CD63 proximal interacting proteins provides insights into network of partners required for endocytic trafficking, extracellular vesicle cargo sorting, formation and secretion.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

This paper proposes a novel facial expression recognition network called the Lightweight Facial Network with Spatial Bias (LFNSB). The LFNSB model balances model complexity and recognition accuracy. It has two key components: a lightweight feature extraction network (LFN) and a Spatial Bias (SB) module for aggregating global information. The LFN introduces combined channel operations and depthwise convolution techniques, effectively reducing the number of parameters while enhancing feature representation capability. The Spatial Bias module enables the model to focus on local facial features while also capturing the dependencies between different facial regions. Additionally, a novel loss function called Cosine-Harmony Loss is designed. This function optimizes the relative positions of feature vectors in high-dimensional space, resulting in better feature separation and clustering. Experimental results on the AffectNet and RAF-DB datasets show that the proposed LFNSB model performs excellently in facial expression recognition tasks. It achieves high recognition accuracy while significantly reducing the number of parameters, thus substantially lowering model complexity.

Detection and measurement of pain are crucial in designing effective pain management interventions to alleviate suffering and prevent functional decline in the medical domain. Traditional methods of pain identification rely on verbal patient reports or observable signs, which can be imprecise or subjective due to variability in patient self-assessments. Hence, there is a pressing need for automated methods to standardize pain measurement procedures. This paper proposes a novel facial expression-based automated pain assessment system as a behavioral indicator for pain evaluation. Our system integrates a fusion structure comprising Convolutional Neural Networks (CNNs) and Tensor-based extended Quantitative Expression Descriptors Analysis (TXQEDA). This innovative approach allows for joint learning of robust pain-related facial expression features from raw facial images, combining RGB appearance with shape-based latent representation. We extensively evaluated our proposed model using the UNBC-McMaster dataset for pain classification and intensity estimation. Our results demonstrate the efficacy of the proposed technique, achieving an impressive accuracy of 99.10% for pain level classification. Furthermore, our system excels in pain intensity estimation, showcasing its potential to provide precise and reliable assessments of pain severity. Overall, our research underscores the importance of automated pain assessment systems in improving patient care and clinical outcomes. By leveraging advanced deep learning techniques and fusion strategies, our proposed model offers a promising approach for standardizing pain measurement procedures and enhancing the quality of pain management interventions.

Optical coherence tomography (OCT) is a non-invasive imaging technique widely used in ophthalmology for visualizing retinal layers, aiding in early detection and monitoring of retinal diseases. OCT is useful for detecting diseases such as age-related macular degeneration (AMD) and diabetic macular edema (DME), which affect millions of people globally. Over the past decade, the area of application of Artificial Intelligence (AI), particularly Deep Learning (DL), has significantly increased. The number of medical applications is also rising, with solutions from other domains being increasingly applied to OCT. The segmentation of biomarkers is an essential problem that can enhance the quality of retinal disease diagnostics. For 3D OCT scans, AI is beneficial since manual segmentation is very labor-intensive. In this paper, we employ the new SAM 2 and MedSAM 2 for the segmentation of OCT volumes for two open-source datasets, comparing their performance with the traditional U-Net. The model achieved an overall Dice score of 0.913 and 0.902 for macular holes (MH) and intraretinal cysts (IRC) on OIMHS and 0.888 and 0.909 for intraretinal fluid (IRF) and pigment epithelial detachment (PED) on the AROI dataset, respectively.

The agricultural sector is undergoing a revolution that requires sustainable solutions to the challenges that arise from traditional farming methods. To address these challenges, technical and sustainable support is needed to develop projects that improve crop performance. This study focuses on the onion crop and the challenges presented throughout its phenological cycle. Aerial monitoring using unmanned aerial vehicles (UAV) and digital image processing were used to identify patterns in the onion crop, including humid areas, weed growth, vegetation deficits, and decreased harvest performance. An algorithm was developed to identify the patterns that most affected crop growth, as the average local production reported was 40.166 ton/ha, but only 25.00 ton/ha was reached due to blight caused by constant humidity and limited sunlight. This resulted in the death of leaves and poor development of bulbs, with 50% of the production being of medium size. It is estimated that approximately 20% of the production was lost due to blight and unfavorable weather conditions.

Practitioners who assess the risk associated with urban trees often factor in the presence or absence of visual tree defects when determining whether a tree may fail. While these defects are a main fixture in many tree risk assessment systems and best management practices, the research supporting their usefulness in predicting tree failure during storms is limited. When looking at past research involving populations of storm-damaged trees, there are several defects that have never predicted failure (or have been associated with reduced rates of failure). In this study, we took a closer look at four such defects: codominant branches; branch unions with included bark; multiple stems originating from the same point; and overextended branches. After Hurricane Ian, we revisited 1519 risk assessed trees where one of these four defects was identified as the primary condition of concern. Fourteen of these trees experienced branch failure during the storm (which hit the study area as a downgraded tropical storm). Upon closer inspection, none of these failures occurred at the defect of concern. Our findings indicate that none of the defects assessed appeared to increase the likelihood of tree failure in the species tested. Our results are in line with past research on these defects derived from post-storm assessments and analysis.

The paper introduces a control hybrid model that is designed on the basis of OOSEM (Object-Oriented Systems Engineering Method), MDA (Model-Driven Architecture) concepts, RealTime UML/SysML (Unified Modeling Language/Systems Modeling Language), and an algorithm based on UKF (Unscented Kalman Filter). This hybrid model enables the implementation of control elements for autonomous underwater vehicles (AUVs) and can be adapted to reuse for most standard AUV platforms. To obtain this goal, the dynamic model of AUV is integrated with the following specializations of OOSEM/MDA, in which the analysis model is clarified via the use-case model definition and then combines with HA (hybrid automata) to precisely define the requirements for control. Next, the designed model is specialized via real-time UML/SysML to get the core control blocks, which describe the behaviors and structures of control parts in detail. This design model is then transformed into the model of implementation with the assistance of round-trip engineering to conveniently realize the controller of AUVs. Based on this new model, an AUV controller for low-cost turtle-shaped AUVs is implemented that performs tracking for a planar trajectory with accepted feasibility.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In order to explore the effect of fertilization patterns on the growth of rapeseed seedlings under waterlogging stress, three fertilization patterns (conventional fertilization, supplemental organic fertilization, and supplemental microbial fertilization) were set up using the variety Xiangyou 708 as the material, and waterlogging treatment was carried out during the seedling stage of rapeseed. The effects of fertilization patterns on the growth of rapeseed seedlings and rhizosphere microorganisms under waterlogging stress were investigated. The results showed that all three fertilization patterns exhibited that waterlogging stress inhibited the growth of rapeseed seedlings, inhibited root activity, and changed the structure of rhizosphere bacterial colonies. However, supplemental organic fertilization and microbial fertilization could better promote the growth of rapeseed seedlings, reduce the impact of waterlogging stress on the growth of rapeseed seedlings, and accelerate the recovery of rapeseed seedlings after waterlogging stress. In addition, supplemental microbial fertilization could also change the structure of rhizosphere bacterial colonies. Under normal water supply, supplemental organic fertilization enriched P_Bacteroidota, P_Actinobacteriota, P_Chloroflexi, and G_Flavisolibacter in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Bacteroidota and G_Flavisolibacter in the rhizosphere soil of rapeseed. After 7 days of waterlogging treatment, supplemental organic fertilization enriched P_Verrucomicrobiota in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Actinobacteriota, G_SC-I-84, and G_Ellin6067 in the rhizosphere soil of rapeseed. The enrichment of these bacteria may be related to the growth promotion and waterlogging tolerance of rapeseed. This study provides evidence that microbial fertilizer and organic fertilizer can promote the growth of rapeseed and enhance its waterlogging tolerance, as well as evidence that some rhizosphere microorganisms have a potential role in promoting the growth and waterlogging tolerance of rapeseed.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

Numerous new technologies have been implemented in image analysis methods that help researchers withdraw scientific conclusions from biological phenomena. Plants of the family Lemnaceae (duckweeds) are the smallest flowering plants in the world, and biometric measurements of single plants and their growth rate are highly challenging. Although the use of software for digital image analysis has changed the way scientists extract phenomenological data (also for studies on duckweeds), the procedure is often not wholly automated and sometimes relies on the intervention of a human operator. Such a constraint can limit the objectivity of the measurements and generally slows down the time required to produce scientific data. Here is the need to implement image analysis software with artificial intelligence that can substitute the human operator. In this paper, we present a new method to study the growth rates of the plants of the Lemnaceae family based on the application of machine learning procedures to digital image analysis. The method is compared to existing analogical and computer-operated procedures. Results showed that our method drastically reduces the time consumption of the human operator while retaining a high correlation in the growth rates measured with other procedures As expected, machine learning methods applied to digital image analysis can overtake the constraints of measuring growth rates of very small plants and might help duckweeds gain worldwide attention thanks to their great nutritional qualities and biological plasticity.

In China, the demand for rabbit meat is also increasing, and the production for rabbit meat is important. However, the underlying mechanisms of regulate skeletal muscle growth and development in rabbits remain unclear. The purpose of this study was to identify candidate genes related to skeletal muscle growth in rabbits and explore their potential regulatory mechanisms. RNA-seq technique was used to compare the differences of skeletal muscle transcriptome in Fujian white rabbits at different developmental stages (day 20 and 26 of embryos and birth 1, 30 and 60-day-olds) with a total of 25 individual selected. A total of 9737 DEGs that were acquired from the five groups were annotated into three ontologies of the GO database: biological process (BP), cell component (CC), and molecular function (MF). For KEGG analysis, there are 8249 genes were enriched in 1148 pathways, of which 67 pathways were significantly enriched, mainly in Hypertrophic cardiomyopathy (HCM), the PPAR signaling pathway, MAPK signaling pathway. Among all comparison groups, SE was the most abundant AS event. Real-time PCR verified that the expression patterns of differential genes were consistent with the transcriptome sequencing results. These results will provide a molecular regulation mechanism of muscle growth and development in Fujian white rabbits, and should serve an important theoretical basis for improving meat performance and growth rate of Chinese local meat rabbit breeds.

Extremely low-frequency electromagnetic fields (ELF-EMF) are ubiquitous in industrial-11 ized environments due to the continuous use of electrical devices. Our previous studies demon-12 strated ELF-EMF affects muscle cells by modulating oxidative stress and enhancing myo-genesis. 13 This pilot study investigated these effects on skeletal muscles of sedentary adult mice, assessing 14 physiological responses to ELF-EMF exposure and potential modulation by antioxidant supplemen-15 tation. Male C57BL/6 mice were exposed to ELF-EMF (0.1 or 1.0 mT) 1 hour/day up to 5 weeks, and 16 fed a standard diet without or with N-acetyl-cysteine (NAC). Results showed transient increases in 17 muscle strength (after 2-weeks’ exposure at 1.0 mT), potentially linked to muscle fiber recruitment 18 and activation, revealed by higher PAX7 and MyH expression levels. After ELF-EMF exposure, ox-19 idative status assessment revealed transient increases in expression levels of SOD1 and catalase en-20 zymes, in total antioxidant capacity and in protein carbonyl levels, marker of oxidative damage. 21 These effects were partially reduced by NAC. In conclusion, ELF-EMF exposure affects skeletal 22 muscle physiology and NAC supplementation partially mitigates these effects, highlighting the 23 complex interactions between ELF-EMF and antioxidant pathways in vivo. Further investigations 24 on ELF-EMF as a therapeutic modality for muscle health are necessary.

Forest-grass intercropping patterns of protected cultivation has been widely used to increase productivity and sustainability in modern agriculture. However, there have been few studies of wolfberry (L. barbarum) intercropping and it is cultivated mostly by clean tillage. This paper takes 10 kinds of wolfberry-forage intercropping patterns, compares the effects of different planting modes on the growth, yield, photosynthetic characteristics, nutritional quality, and the degree of occurrence of diseases and pests, which aims to make clear the effects of wolfberry-forage intercropping patterns on wolfberry. The results showed that different intercropping combinations had different effects on wolfberry. The overall effect of Wolfberry-forage intercropping patterns on the growth of wolfberry were promote the photosynthetic characteristics. Ryegrass could increase the branch number, Lvyuan 5 and mangel increase branch length; Mangel, clover, sweet sorghum, ryegrass and stipas could reduce the damage of powdery mildew by 69%, and alfalfa, stipa and ryegrass could reduce the occurrence of aphids by 67% (P<0.05). Intercropping could increase carotenoids, flavonoids and ascorbic acid contents to improve wolfberry quality by 21%, 53% and 127%, respectively (P<0.05). Among all the performances, wolfberry-mangel intercropping has absolute advantages in promoting wolfberry yield and quality increase. Therefore the best patterns of wolfberry-mangel, wolfberry-ryegrass, wolfberry-alfalfa and wolfberry-clover were chosen.

Artificial intelligence (AI) is a versatile term that is a conclusive remedy to solve the problem using past rational data after deep contemplation using these terms i-e basic statistics, carving data, familiarity with common AI algorithms. Seafood especially tiger prawn export as a busi-ness will provide enormous foreign exchange to any country if the farmers overcome the corre-lated vulnerabilities in prawn farming. This research is elucidating lacking in Tiger prawn (TP) farming like curbing of Oxygen, pH, water temperature, and nutrients, etc. Moreover, hatchery statistics in terms of juveniles will depict this study's clear picture of curbed aquaculture. For normative decisions, the Analytical Hierarchical Process (AHP) is used. The problem which has been faced by local prawn farmers that there is a stagnant TP growth in ponds, the reason is the predominant sensitivity factor in TP. For this reason, they need indemnification of thirteen fac-tors with natural resources to get the plausible results to get calmness in their lives. This study will solely focus on the TP growth model, and the monitoring effect will be established by the Artificial Intelligence algorithm. This study will employ the AHP, 0-1 scaling method, data cura-tion techniques, and ecological statistics. The life of Tiger Prawn (TP) depends upon these factors mainly, a) Physical and b) Chemical parameters. Physical parameters contain environment (E) provided to TP like season (S) and temperature (T) etc. whereas the quality of Ammonia NH3 (N) from fish waste, Oxygen level (O), and water quality hard & soft (W) lies in chemicals do-main. This research will Elucidate the factors which cause conceptual muddles in the aquamarine life of TP, for this reason, Statistical tools will assess the current result, forecast the gap. AHP will analyze the domain inputs, circumspect ramification which will depict visceral factors, later results depict which pond suits the TP. In curtail, these factors will be curbed to improve the growth of TP in a control conditioned environment.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

Manufacturing of facial epithesis is a complex technological process including several traditional stages of production, accompanied by aggravated psycho-emotional status of the patient. One of the main factors causing discomfort in patients with facial defects is the process of obtaining silicone impressions from the wound surface and the long waiting period for the final epithesis. Active development of digital technologies in medicine and dentistry helps specialists not only to automate most of the traditional stages of manufacturing of dento-mandibular and facial prostheses, but also improves the quality of life of patients by increasing the efficiency of services and reducing the production time of prosthetic structures. The application of digital technologies in the production of facial epithesis was difficult due to the lack of specialized 3D-software for modeling and material for further additive manufacturing of structures. The authors developed a unique technology for 3D modeling and additive manufacturing of facial epithesis, including a 3D CAD module and material for 3D printing. The primary objective was to fabricate immediate facial prostheses in the postoperative period in the shortest possible time until the final epithesis was fabricated.

Starch is considered a major nutritional factor of maize (Zea mays L.) kernels, and can be influenced by the type of endosperm. The effects of endosperm type (vitreous and non-vitreous) and type of soil (clay and sand) on the starch content of kernels of maize, and on the in vitro degradation of starch were investigated in the rumen fluid after harvesting at 6 different maturity stages during 2008 and five different maturity stages in 2009. Starch degradation, in rumen fluid, was determined after 6 h, 12 h and 20 h of incubation, using the technique of gas production. A positive linear relationship was observed during gas production (ml gas/g organic matter) and starch degradation (g kg^-1 starch) at all incubation times, with starch contents of maize kernels to a certain limit of starch accumulation (i.e. at starch contents 451-519 g/kg OM) and negative relationship afterwards. This suggests significant effects of maturity on ruminal starch degradation of maize kernels. At each harvest date, ruminal starch degradation of maize kernels was affected by crop genotype as well as soil type. The in vitro ruminal degradation potential of starch in maize kernels was influenced by the nature of the endosperm, with a higher degradation of non-vitreous kernels than of vitreous kernels. The rumen starch degradation was also influenced by type of soil, with better degradation on clay than sandy soil. For all the incubation times and maturity stages the effects of genotype, soil type and maturity stage were consistent in rumen fluid.

Sexual Violence (SV) can deeply impact victims' physical and psychosocial well-being. Yet many healthcare providers, including registered nurses (RNs), hesitate to screen patients due to a lack of confidence and knowledge. The SATELLITE Sexual Violence Assessment and Care Guide was developed to address this gap; however, the guide’s educational effectiveness remained untested. This pilot study aimed to assess the feasibility, acceptability, and efficacy of an education program based on the SATELLITE guide among RNs in clinical settings, using a pre- and post-test design. Results indicated that the education was not only feasible and acceptable, but also demonstrated the effects as desired with significant increases in RNs' knowledge and confidence in SV screening and care. The program's assessment tool was valid and reliable, and participant recruitment was feasible. Based on these findings, it is recommended that the SATELLITE education program be further tested with a larger RN sample and extended to other healthcare providers. Additionally, exploring different regions, cultural contexts, and healthcare settings would enhance understanding of the program's broader applicability and effectiveness.

Proteins play a pivotal role in supporting athletes by promoting muscle hypertrophy and minimizing protein catabolism during exercise. They stimulate muscle protein synthesis, aiding in the repair of exercise-induced muscle damage and serving as an energy source, particularly for post-exercise glycogen replenishment. In individuals with phenylketonuria (PKU), for whom protein intake is limited to essential phenylalanine (Phe), supplementation with Phe-free amino acids or glycomacropeptides is necessary. Tailored for macronutrient and micronutrient content, these protein substitutes fulfill most protein requirements, but lack Phe, unlike dietary sources of protein. Protein requirements for athletes with PKU exceed general recommendations due to limited availability in supplements and potential catabolism mitigation. Various factors influence tolerated dietary Phe in PKU, including protein substitute quantity, distribution, pharmacological treatment, age, growth rate, pregnancy, catabolic states, and physical activity. While general protein requirements for PKU surpass those of the general population, adherence to supplement regimens is crucial for athletes and patients with PKU. Strategically timed protein substitutes enhance muscle protein synthesis, body composition, and sports performance within safety limits. Individualized intake is essential for optimal outcomes, as proteins have a multifaceted role in optimizing athletic performance and addressing challenges in PKU.

Facial expressions play a key role in interpersonal communication when it comes to negotiating our emotions and intentions, as well as interpreting those of others. Research has shown that we can connect to other people better when we exhibit signs of empathy and facial mimicry. However, the relationship between empathy and facial mimicry is still debated. Among the factors contributing to the difference in results across existing studies is the use of different instruments for measuring both empathy and facial mimicry, as well as often ignoring the differences across various demographic groups. This study first looks at the differences in empathetic abilities of people across different demographic groups based on gender, ethnicity and age. The empathetic ability is measured based on the Empathy Quotient capturing a balanced representation of both emotional and cognitive empathy. Using statistical and machine learning methods, the study then investigates the correlation between the empathetic ability and facial mimicry of subjects in response to images portraying different emotions displayed on a computer screen. Unlike the existing studies measuring facial mimicry using electromyography, this study employs a technology detecting facial expressions based on video capture and deep learning. This choice was made in the context of increased online communication during and post the COVID-19 pandemic. The results of this study confirm the previously reported difference in the empathetic ability between females and males. However, no significant difference in the empathetic ability was found across different age and ethnic groups. Furthermore, no strong correlation was found between empathy and facial reactions to faces portraying different emotions shown on a computer screen. Overall, the results of this study can be used to inform the design of online communication technologies and tools for training empathy team leaders, educators, social, and health care providers.