The present study describes the activities performed to test a new method for measuring the mobility of polycyclic aromatic hydrocarbons (PAHs) in the solid phase of sediments within the context of environmental pollution risk assessment. The method is based on the design of a new configuration (new materials) of the commercial passive sampler Chemcatcher as probe for predicting the bioavailability of persistent organic pollutants in marine sediments (or in water saturated soils).

The aim of the present study was to investigate the incidence of breast (females), prostate, testicular and thyroid cancer in the Italian National Priority Contaminated Sites (NPCSs), served by cancer registries, where the presence of endocrine disruptors (EDs), reported to be linked to these tumors, was documented. Evidence of carcinogenicity of EDs present in NPCs was assessed based on evaluation by international scientific institutions/committees. Standardized Incidence Ratios (SIRs) were computed for each NPCS and cancer site with reference to the time window 1996-2005. Excess incidence of one or more cancer site at study was found in twelve out of fourteen NPCSs. Significantly increased SIRs were found for breast cancer in eight NPCSs, for prostate cancer in six, for thyroid cancer (both gender) in four and for testicular cancer in two. Non significantly increased SIRs were found in five NPCSs for testicular cancer and in two for thyroid cancer (males). Even if increased incidence of one or more cancer sites at study were found in several NPCSs, the ecological study design and the multifactorial etiology of the considered tumors do not allow reaching conclusions in terms of causal links with environmental contamination. In light of the observation of some excesses in SIRs, continuing epidemiological surveillance is warranted.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

Eelgrass meadows have attracted a lot of attention not only for their ability to maintain marine ecosystems as feeding grounds for marine organisms, but also for their potential to store atmos-pheric and dissolved CO2 as blue carbon. This study comprehensively evaluated the bacterial and chemical composition data obtained from eelgrass sediments of different scales along the coast of Japan to investigate the sediment effect on the acclimatization of eelgrass. Regardless eelgrass habitat, approximately 1% Anaerolineales, Babeliales, Cytophagales, and Phycisphaerales were present in the bottom sediment. Sulfate-reducing bacteria (SRB) were present at 3.69 % in eelgrass sediment compared to 1.70 % in bare sediment. Sulfur-oxidizing bacteria (SOB) were present at 2.81% and 1.10% in the eelgrass and bare sediment, respectively. Bacterial composition analysis and linear discriminant analysis revealed that sulfur-oxidizing bacteria detoxified H2S in the eelgrass meadows and that the larger-scale eelgrass meadows had a higher diversity of sul-fur-oxidizing bacteria. Our result indicated that one of the following systems detoxifies the H2S in eelgrass meadows microbial oxidation by sulfur-oxidizing bacteria, oxidation by O2 perme-ated by the physical diffusion of benthos. This study indicated the issues of maintaining sustain-able conservation of the eelgrass bed.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

The detection of SARS-Cov-2 in the sewage and water resources has increased the awareness among the people about the possibility survival of SARS-Cov-2 in the environment and the potential to transmit into the human through food chain or water resources. Moreover, the surface contaminated by the virus need to be disinfected frequently by using an effective disinfectant, the current chapter discussed the efficiency of the most traditional treatment process of the sewage and wastewater, and their role in the elimination of the virus as well as the sterility assurance level concept. Moreover, the chemical disinfectant used currently and their temporary efficiency has been reviewed.

This study was conducted to identify soil cadmium (Cd) removal pathways and their contribution rates during phytoremediation by Pennisetum hybridum, as well as to comprehensively assess its phytoremediation potential. Multilayered soil column tests and farmland simulating lysimeter tests were conducted to investigate the Cd phytoextraction and migration patterns in topsoil and subsoil simultaneously. The aboveground annual yield of P. hybridum grown in the lysimeter was 206 ton·ha–1. The total amount of Cd extracted in P. hybridum shoots was 234 g·ha–1, which was similar to that of other typical phytoremediation plants. After the test, the topsoil Cd removal rate was 21.50%–35.81%, whereas the extraction efficiency in P. hybridum shoots was only 4.17%–8.53%. These findings indicate that extraction by plant shoots was not the most important contributor to the decrease of Cd in the topsoil. The proportions of Cd retained by root cell wall was approximately 50% of the total Cd in root. Based on column test results, P. hybridum treatment led to a significant decrease in soil pH and considerably enhanced Cd migration to subsoil and groundwater. P. hybridum decreases Cd in the topsoil through multiple pathways and provides a relatively ideal material for phytoremediation of Cd-contaminated soils.

Beach sand may act as a reservoir for numerous micro-organisms, including enteric pathogens. Several of these pathogens originate in human or animal feces, which may pose a public health risk. In August 2019, high levels of fecal indicator bacteria (FIB) were detected in the sand of the Azorean beach Prainha, Terceira Island, Portugal. Remediation measures were promptly implemented, including sand removal and the spraying of chlorine to restore the beach sand quality. To determine the biological source of the contamination, during the first campaign, supratidal sand samples were collected from several sites along the beach, followed by microbial source tracking (MST) analyses of Bacteroides markers for five animal species, including humans. Some of the sampling sites revealed the presence of marker genes from dogs, seagulls, and ruminants. Making use of the information on biological sources originating partially from dogs, the municipality enforced restrictive measures for dog-walking at the beach. Subsequent sampling campaigns detected low FIB contamination due to the mitigation and remediation measures that were undertaken, thereby no longer requiring MST marker-gene analysis. This is the first case study where the MST approach was used to determine the contamination sources in the supratidal sand of a coastal beach. Our results show that MST can be an essential approach to determine sources of fecal contamination in the sand. This study shows the importance of holistic management of beaches that should go beyond water quality monitoring for FIB, putting forth evidence for the need for sands also to be monitored.

The BIOTON® biochar, produced by a wood biomass pyrolysis process, usually applied as a soil amendment, was investigated for a novel application, i.e. the adsorption of lead from contaminated solutions. The experimental activity firstly included the physical-chemical characterization of BIOTON®; SEM images were also obtained to highlight its internal structure. The adsorption process was investigated through batch and column experiments. Adsorption kinetics showed a very rapid achievement of the equilibrium conditions, i.e. at 2h and 4h for 50 mg/L and 100 mg/L initial Pb concentration, respectively. Complete removal also occurred within the same time. The Brunauer–Emmett–Teller model better fitted the equilibrium data for both Pb concentrations, whereas the kinetics were best represented by the pseudo second order model. The column tests showed that the addition of biochar as adsorbent media within the bed significantly extended the time of breakthrough and exhaustion, with respect to the column filled with soil only. The adsorption capacities of BIOTON® versus lead solutions was found to be comparable to that reported for commercial adsorbents. Therefore, BIOTON® can be considered a valid option, with the additional benefit to reduce the environmental impact since allows to recover a residue which alternately would need to be disposed of.

Wetlands are carriers of metals and organic pollutants from natural and anthropogenic sources. Studies have shown that sediments are sinks for these pollutants as they carry more than 99% of the total amount of metals which are released as soluble metals into the Lagoon. The University of Lagos, located at Akoka North eastern part of Yaba in Lagos Mainland runs along a highly industrialized and residential area. This paper reports the total metal concentrations in wetland and sediment and their seasonal variations. Wetland and sediment samples were collected for two seasons in 8 sampling sites. Results showed wetland data having lower concentrations of metals as compared to sediments. Wet season had higher concentrations of metals as compared to other season. Total concentrations in wetlands were Cd (1.0-6.0), Cu (1.0-11.0), Cr (0.3-82.7), Zn (2.7-65.0) and Pb (0.3-16.0) all in μg L-1 respectively. Statistical analysis showed that there was a significant difference between the wet and dry seasons for sediments. Cd was the only metal at acceptable levels while Cr, Cu, Pb and Zn concentrations all exceeded levels deemed acceptable by the SABS and the EPA. Therefore, the wetland is in poor health.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

Carbon dioxide capture and storage (CCS) is highly expected to be mitigating the discharges of carbon dioxide in a surrounding environment. Solvents are an integral part of CCS. So far, several solvents have been explored the interest of meeting the requirements such as accessibility, non-harmfulness, biocompatibility, recyclability, and inexpensiveness. However, most solvents face failure in fulfilling the requirements due to many factors, so, this review paper gives a brief discussion about another category of solvent, an analogue of ionic liquids (ILs) named deep eutectic solvent (DES). Extensive research has been done on DES in recent years because of their various attractive advantages, i.e., non-poisonousness, biodegradability, cheap cost and easy preparation, that make them as a promising green solvent for many industrial procedure and application, for instance, polymer synthesis, biodiesel treatment, green chemistry, electrochemistry etc. Therefore, this manuscript mainly focusses on CO2 capturing through DES in oil and gas field. In addition, the preparation and chemical structures of this novel solvent (DES) is also discussed. Moreover, a detailed study based on experimental solubility of CO2 in DESs is also reported in this article.

Arsenic is naturally present in many geological formations around the world and is a major source of groundwater contamination. Bolivia is not exempt from this problem. Physical-chemical studies of water quality in deep and shallow wells have determined the presence of arsenic in some areas of the Bolivian Altiplano, valleys, and plains. In the Lake Poopó basin, water from shallow wells (up to 30 m) has arsenic concentrations that exceed the Bolivian drinking water standard and the WHO recommendation of 10 μg-As/l by up to 25 times. In peri-urban areas of Cochabamba, the arsenic content in groundwater is up to 113 μg-As/l. chronic exposure to arsenic is associated with neurological and dermatological problems and carcinogenic effects. To date, no measures have been taken to mitigate the arsenic problem for the rural population, who often rely on arsenic-contaminated water as their only source of drinking water. This contamination represents a serious threat to the health and economic well-being of the inhabitants and ecosystem in these areas. In this work, for arsenic removal, iron and iron oxide nanoparticles obtained from recycling metal chips by top-down and bottom-up technology have been used for arsenic adsorption in an experimental filter combined with other artisanal filtering materials in the form of layers. The results have shown that water contaminated with arsenic after passing through the filter reduces the concentration of total arsenic filtered from 83, 52 ppb to less than 5 ppb, less than the Bolivian standard 512 of 10 ppb for drinking water.

This work aimed to carry out a bioremediation study to evaluate the resistance of Penicillium sp. isolated from kefir grains for the treatment of copper. The fungal culture medium was prepared using a 2% malt-agar medium at pH 7.0 in which Penicillium sp. was inoculated. Penicillium sp. growing in a liquid medium showed a decrease in biomass in presence of Cu(NO3)2 (800 mg.L-1), suggesting that the metal impacts the growth rate of the fungus. Moreover, the combined factors of pH and the presence of the inorganic contaminant impacted the radial growth of the fungus, causing inhibition of 73% at pH 4.0, 75% at pH 7.0, and 77% at pH 9.0 in liquid medium compared to control. However, images obtained with scanning electron microscopy showed the integrity of the fungus cell, even at high doses of copper in the medium. Therefore, it can be concluded that Penicillium sp. isolated from kefir grain can bioremediate the environment and that the harmful effects of heavy metals can be minimized as a result biosorption. Although the growth of Penicillium sp. is inhibited, such retardation requires high doses of copper nitrate, thus ensuring the use of this microorganism for protection against the harmful effects of non-essential copper in the environment.

Soil contamination with petroleum hydrocarbons (PHCs) has become a global concern in the word due to intensification of industrial activities. This creates a serious environmental issue, therefore there is a need to find solutions, including application of efficient remediation technologies, or to improve current techniques. Rhizoremediation is a sub-category of the phytoremediation which refers to Phytomanagement that uses plants and their associated microbiota. These green technologies have received a global attention as a cost-effective and possible efficient remediation technique that can be applied to cleanup PHCs-polluted soils. The mechanism of rhizoremediation process is that plant roots stimulate soil microbes to mineralize organic contaminants to H2O and CO2. However, this multipartite interaction is much complex because many biotic and abiotic factors can influence microbial processes in the soil, making the efficiency of rhizoremediation unpredictable. This review reports the progress made on rhizoremediation approaches that can overcome the limitations and improve the efficiency of PHCs-contaminated soils. The addressed approaches in this review include: 1) selecting plants with desired characteristics suitable for rhizoremediation, 2) the exploitation and manipulation of plant microbiome by using inoculant containing plant growth-promoting rhizobacteria (PGPR) or hydrocarbon-degrading microbes, or a combination of both types of organisms, and 3) enhancement of the understanding of how host-plant assembles a beneficial microbiome, and how it functions, under pollutant stress.

Mineral extraction is one of the most important for the economies of different countries, and Brazil is one of the world's primary iron ore producers. Unfortunately, the dams are still the main problem, mainly in Minas Gerais, especially after the Fundão Dam rupture happened in 2015. Additionally, there is still a massive presence of buildings produced on earth throughout the Minas Gerais mining region, built from the 18th century to today. Investigating the potential of IOT to be incorporated into traditional earthen construction techniques in regions affected by dam ruptures presents a relevant and innovative research approach. In addition, the local reuse of these sediments should be the priority. Thus, the main objective of this work was to collect, characterize, and analyze the possibilities of application of these tailings to produce RE. XRD, XRF, granulometry, porosity, specific density, toxicity, and MEV/EDS were performed on the samples collected at three points. To analyze the soil-IOT compatibility, representative mixtures of RE were produced, and the specific mass, compaction, and compressive strength were performed. It was observed that the IoT samples have a high silica content and that the mixtures of IOT-soil, even without cement, reached compressive strength values above the current international standards.

Diatom assemblages in mud volcanoes are quite rare and poorly studied. The finding of a rich diatom flora in the sediments of the Daginsky Mud Volcano (DMV), located in the tidal zone of the Nyisky Bay of the Sea of Okhotsk, is interesting for studying the conditions for the formation of host sediments in the zone of influence of various extreme factors, such as outflows of gases and water-mud mass, thermal springs, and tides, etc. For this purpose, the composition of diatoms and their concentration in DMV sediments were studied, a comparison was made with diatoms of geothermal springs of the Russian Far East associated with volcanic activity, and the stratigraphic distribution of the found extinct diatoms was analyzed, which is important for determining their source and age of mud volcano roots. Diatom assemblages from DMV sediments are mainly characterized by the predominance of Metascolioneis tumida, Paralia sulcata, Odontella aurita, Pinnunavis yarrensis, Petroneis marina, Cocconeis scutellum, and Navicula digitoradiata. They consist of diatoms of different biotopes and extinct species. The diversity and abundance of brackish water and marine species indicates the predominant influence of sea waters on the formation of DMV sediments. The diverse freshwater species were mainly introduced into sediments with river runoff, but it is likely that some of them, cosmopolitan alkaliphilic species, are inhabitants of geothermal springs. The presence of extinct species from the underlying Neogene sediments from where they were carried with gas-water-mud masses, is the most typical for diatom assemblages of the DMV.

Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

In 2021 the total world cement production was estimated at 4.1 billion tonnes and the annual CO2 emissions from cement plants reached almost 2.8 billion metric tonnes. In the last years many ef-forts have been made for manufacturing low-CO2 cements. In this regard, a great attention has been paid towards calcium sulfoaluminate (CSA) cements for both their peculiar technical prop-erties and the environmentally friendly features mainly related to their manufacturing process. Moreover, the use of blended cements composed by CSA binders and supplementary cementitious materials (SCMs) could represents a powerful tool for both reducing the CO2 footprint and pro-ducing more durable environmentally friendly materials. In this paper, the possibility of using reservoir sediments (RS), calcined at 830°C, as SCMs in blended-CSA cements was investigated. Four binders were submitted to hydration and physico-mechanical tests for curing periods com-prised in the interval 4 hours-56 days. X-ray fluorescence, X-ray diffraction and differential thermal–thermogravimetric analyses were employed as main characterization techniques. It was found that thermally treated RS are very interesting inasmuch as their utilization allows a CSA clinker dilution, thus implying both a decrease of CO2 emissions and a reduction of costs related to CSA cement production.

A two-year field experiment (2022–2023) was carried out to investigate the impact of different sowing periods (spring and winter) and nitrogen levels (0, 30, 60 kg/ha) on the phytoextraction potential of flax. The study site is characterized by high concentrations of heavy metals (Cd, Ni, Cu, Pb, Zn) and belongs to the Mediterranean climate type. Flax (var. Calista) was sown in the spring of 2022 and in the winter of 2023, following a split plot experimental design with three rep-lications, and applying low-input practices. Results showed that spring-sown flax produced short-er but thicker plants with significantly higher biomass (5.27 tn ha-1) when treated with 30 kg ha-1 N compared to winter-sown (2.30 tn ha-1) when treated with 60 kg ha-1 N. The concentration of contaminants in the aerial biomass varied according to metal type and sowing period. The higher biomass production in spring resulted in a higher quantity of heavy metals being removed from the soil, making flax a promising crop for phytoextraction purposes, especially in soils contami-nated with multiple heavy metals.

The contamination on the insulators may increase its surface conductivity and, as a consequence, electrical discharges occur more frequently, which can lead to interruptions in the power supply. To maintain reliability in the electrical distribution power system, components that have lost their insulating properties must be replaced. Identifying the components that need maintenance, is a difficult task as there are several levels of contamination that are hardly noticed during inspections. To improve the quality of inspections, this paper proposes to use the k-nearest neighbours (k-NN) to classify the levels of insulator contamination, based on the image of insulators at various levels of contamination simulated in the laboratory. Using computer vision features such as mean, variance, asymmetry, kurtosis, energy, and entropy are used for training the k-NN. To assess the robustness of the proposed approach, statistical analysis and a comparative assessment with well-consolidated algorithms such as decision tree, ensemble subspace, and support vector machine models are presented. The k-NN showed results of up to 85.17 % accuracy using the k-fold cross-validation method, with an average accuracy higher than 82 % for multi-classification of the contamination of the insulators, being superior to the compared models.

Heavy metals are toxic, persistent and non-degradable. After sedimentation and adsorption, they accumulate in water sediments. The aim of this study was to understand the heavy metal pollution of Qinjiang River sediments on the ecological environment and apportioning sources. The mean total concentrations of Mn, Zn, Cr, Cu, and Pb are 3.14, 2.33, 1.39, 5.79, and 1.33 times higher than the background values, respectively, except for the Co, Ni, and Cd, which are lower than the background values; Fe, Co, Ni, Cd, Cr, Cu, and Pb are all primarily in the residual state, while Mn and Zn are primarily in the acid-soluble and oxidizable states, respectively. Igeo, RI, SQGs and RAC together indicate that the pollution status and ecological risk of heavy metals in Qinjiang River sediments are generally moderate; among them, Fe, Co, Ni, Cd, Cr, and Pb are not harmful to the ecological environment of the Qinjiang River. Cu is not readily released because of its higher residual composition, depicting that Cu is less harmful to the ecological environment. Mn and Zn, as the primary pollution factors of the Qinjiang River, are harmful to the ecological environment. This heavy metal pollution in surface sediments of the Qinjiang River primarily comes from manganese and zinc ore mining. Manganese carbonate and its weathered secondary manganese oxide are frequently associated with a significant amount of residual copper and Cd, as a higher pH is suitable for the deposition and enrichment of these heavy metals. Lead-zinc ore and its weathering products form organic compounds with residual Fe, Co, Cr, and Ni, and their content is related to salinity. The risk assessment results of heavy metals in sediments provide an important theoretical basis for the prevention and control of heavy metal pollution in Qinjiang River.

In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

Heavy metals, including arsenic from abandoned mines, are easily transported with sediment and deposited in water bodies such as reservoirs and lakes, creating critical water quality issues when they are released. Understanding the leaching of heavy metals is necessary for developing efficient water quality improvement plans. This study investigated how arsenic leaches from different soil types and responds to hydrologic conditions to identify areas susceptible to arsenic contamination. In this study, batch- and column-leaching tests and sequential extraction procedures were used to examine arsenic leaching processes in detail. The results showed that most arsenic-loaded sediments accumulated in the vicinity of a reservoir inlet, and arsenic in reservoir beds have a higher leaching potential than those from agricultural land and river beds. Arsenic deposited at the bottom of reservoirs had higher mobility than that in the other soils, and arsenic leaching was closely associated with the acidity of water. In addition, arsenic leaching was found to be responsive to seasons (wet or dry) as its mobilization is controlled by organic compounds that vary over time. The results suggested that temporal variations in the hydrochemical composition of reservoir water should be considered when defining a management plan for reservoir water quality.

Bacteria and archaea participate in and are influenced by processes of substance circulation and energy exchanges in natural environment. Generally, the community changes of bacteria and archaea in sediment are mainly driven by seasonality in mid-latitude regions. But in our study, water diversion to Fen river played a more important role on OTU number, diversity and community structure of bacteria and archaea in sediment than seasonal variation, which was found by 16S rRNA high-throughput sequencing technology. This phenomenon might be caused by external transferred water on the physicochemical water environment and accelerated release of positive nitrogen from sediment caused by rise of water level. Changes of carbon-nitrogen cycle and increase of electrical conductivity (EC) value induced more diversion-responders than season-responders both for bacteria and archaea. Seasonal changes have been influencing bacteria and archaea mildly throughout the whole study reach. After water diversion, the environment indicators relating to bacteria community obviously changed from nutrients to salinity while that for archaea almost disappeared. Our research showed the effects of human activities on the communities of bacteria and archaea outweigh the forcing from natural seasonal changes in mid-latitude regions and revealed the mechanism, highlighting different responses of bacteria and archaea to environmental changes.

Documenting prehistoric and historical hemp retting for fiber extraction is important in the study of human uses of this iconic plant and its cultural implications. In paleoecology, hemp retting is usually inferred from indirect proxies, notably anomalously high percentages of Cannabis pollen in lake sediments, but some recent studies have also used specific molecular biomarkers (cannabinol, Cannabis DNA) as a more straightforward evidence. Here we provide direct evidence of hemp retting by identifying phylogenetic signatures (16S rRNA genes) from pectinolytic bacteria actually responsible for the fermentation process that separates the fiber from the stalk, namely Bacillus, Clostridium, Escherichia, Massilia, Methylobacterium, Pseusomonas, Rhizobium and Rhodobacter. These analyses have been performed in the sediments from an Iberian lake previously considered as an important hemp retting site during the last five centuries, on the basis of Cannabis pollen abundances. The good match between biomarker and pollen evidence, in the context of the recent historical development of hemp industry in Spain, can be useful to interpret paleoecological records from other similar lakes in the way toward a more regional view on the introduction, spreading, uses and associated cultural connotations of Cannabis in the Iberian Peninsula within European and Mediterranean contexts.

This paper presents a limited scope dynamic probabilistic risk assessment (D-PRA) on the survivability of commercial of the shelf (COTS) drones tasked with surveilling areas with varying radiation levels after a nuclear accident. The D-PRA is based on a discrete-dynamic event tree (D-DET) approach, which couples with the OpenEPL error propagation framework to model sequences leading to Loss of Mission (LOM) scenarios due to component failures in the drone’s navigation system. Radiation effects are simulated by calculating the total ionizing dose (TID) against the permissible limit per component, and errors are propagated within the electronic hardware and software blocks to quantify navigation system availability per radiation zone. The proposed methods are integrated into the traditional event tree/fault tree approach and the most vulnerable components are radiation-hardened (RAD-HARD) to the extent specified by a predefined mission success criterion. The results demonstrate the usefulness of the proposed approach in performing trade studies for incorporating COTS components into RAD-HARD drone designs.

Cationised hemp cellulose was prepared by etherification with two quaternary ammonium salts: 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CHPTAC) and glycidyltrimethylammonium chloride (GTMAC) and examined for (i) the efficiency of Cr(VI) removal under acid mine-drainage (AMD) conditions, and (ii) antibacterial activity. Adsorbents were characterised by electron microscopy, Fourier transform infrared (FTIR), CP-MAS ¹³C nuclear magnetic resonance (NMR) spectroscopy, elemental composition and surface charge. FTIR and solid state ¹³C NMR confirmed the introduction of quaternary ammonium moieties on cellulose. ¹³C NMR also showed that cationisation decreased the degree of crystallisation and lateral dimensions of cellulose fibrils. Nevertheless, 47 % - 72% of Cr(VI) ions were removed from solutions at pH 4, by 0.1 g of CHPTAC and GTMAC-cationised cellulose, respectively. Adsorption kinetics followed the pseudo-second order model and isotherms were best described by the Freundlich and Dubinin-Radushkevich models. When GTMAC-modified cellulose was applied to AMD contaminated water (pH 2.7), however, Cr(VI) uptake removal decreased to 22% likely due to competition from Al and Fe ions. Nevertheless, cationised materials displayed considerable antibacterial effects, reducing the viability of Escherichia coli by up to 45 % after just 3 hours of exposure. Together, these results suggest that cationised cellulose can be applied in the treatment of Cr(VI)-contaminated mine water particularly if pre-treatments to reduce Fe and Al concentrations are applied.

Soil washing is a rapid and efficient method for heavy metals removal. In this study, in order to prove the feasibility of leaching remediation technology for remediation of lead-contaminated soil around a smelter, intermittent oscillating washing tests and extensive continuous tests were conducted to remediate Pb contaminated soils. Plant growth tests with wheat (Bainong Aikang 58) were also conducted to investigate the effects of leaching on plant growth and the Pb content of stems and leaves. The results revealed that in soils, Pb mainly exists in the forms of PbCO3, Pb5(PO4)3Cl2, PbSO4, and in small amounts of PbS. The intermittent oscillating washing tests showed that a lower liquidsolid(L/S) ratio and a higher leaching temperature and time were related to increased Pb removal efficiency. The Pb removal efficiency rates in the oscillating washing tests and the extensive continuous tests were 72.50% and 69.94%, respectively. In addition, the chemical and physical characteristics of the soil were basically unchanged after the leaching regimes. The results of the plant growth tests showed that the leaching regimes did not have a negative effect on the survival rate and growth of the wheat, and the heavy metal contents of the stem and leaf were effectively reduced. This study provides a reference for the large-scale remediation of contaminated soils.

We estimated the daily intakes of chlorpyrifos and cypermethrin via ingestion of indoor dust and outdoor soils using the Stochastic Human Exposure and Dose Simulation Model on a probabilistic approach for Taiwan’s homes. Variable information for the daily intake estimation, such as concentration, ingestion rate, body weight, was adopted from previous studies. Monte Carlo simulation was performed with 1,000,000 iterations to simulate a single daily intake, which was shown in terms of percentage of the Acceptable Daily Intake (ADI) of either insecticide. The daily intakes were minimal with a 99% probability; at 99.9th percentile, however, the total intakes leaped to 13.1% and 20.0% of the respective ADIs of chlorpyrifos and cypermethrin. The sensitivity analysis indicated that concentration was the most determinant variable. Compared to the data of daily intakes via dietary ingestion of vegetables derived from a previous study, the estimated intakes by this study were considerable at the highest percentile, which referred to insecticide residues few days after insecticide application. Consequently, the non-dietary ingestion exposure to either insecticide was negligible in most cases; nevertheless, for those with indoor insecticide applications, the daily intakes for young children could be of concern. Frequently home cleaning is recommended to reduce the exposure.

Mining-induced water contamination remains a significant concern in many regions of the world due to the high concentrations of toxic ions often associated with it. In this study, cellulose-supported ferrihydrite composites (CNF-Fe) were prepared by seeding of ferrihydrite nanoparticles on cellulose nanofibres (CNFs) and employed for the removal of As(III), As(V) and Cr(VI) from contaminated water. The adsorbent was characterized by electron microscopy, gas adsorption, point of zero charge (pH_PZC), X-ray diffractometry (XRD), as well as infrared and Raman spectroscopy. Compared to parent CNFs, CNF-Fe adsorbents had lower crystallinity and a higher surface area: 218.76 m² g^-1. Further, with a pH_PZC of 6.3, CNF-Fe was positively charged at low pH and suitable for adsorption of anions at acidic conditions characteristic of acid mine drainage. In single-ions solutions, the removal efficiency of CNF-Fe was in the order Cr(VI)>As(V)>As(III) (i.e. 0.15, 0.12 and 0.11 mg g^-1 respectively). Adsorption kinetics followed the pseudo second-order model and isotherms were best fitted by the Freundlich, Dubinin-Radushkevich, and Temkin models. However, when CNF-Fe was applied to AMD-contaminated water (pH 2.7), Cr(VI) uptake decreased to ~39% which was likely due to competition from sulphate and selenium ions. Nevertheless, the adsorbent displayed regeneration capabilities with ~98% As and ~45% Cr desorbed after 24 hours of treatment. Together, these results suggest that cellulose supported ferrihydrite composites can be applied in treatment of mine drainage-contaminated water in conjunction with pre-treatments that limit SO₄^2- and selenium concentrations.

This article discusses the results of fluid inclusions study in barite collected at the Jan Mayen vent field area (Troll Wall and Perle & Bruce) and Loki’s Castle vent field of the Mohns Ridge segment of the Arctic Mid-Ocean Ridge. Three mafic-hosted volcanogenic massive sulfide deposits were examined within the active vent fields that adequately correspond to geological settings of ultraslow-spreading ridges and PT-conditions. Hydrothermal sediments were investigated to determine the temperature and salinity of the fluids responsible for barite precipitation. The hydrothermal origin of the barite was confirmed by its morphology. Fluid inclusions are two-phase and homogenized into the liquid phase on heating at temperatures below 287ºC. The salt concentration in fluids trapped in inclusions is 2.6–4.4 wt.% NaCl eq. The crystallization temperatures varied from 276ºС to 119ºС and from 307ºС to 223ºС for the Jan Mayen and Loki’s Castle vent fields, respectively. The data obtained allowed us to confirm evidence of fluid phase separation in the hydrothermal systems and to expand our knowledge of the temperature and salinity of mineral fluids previously known from recent direct measurements during the cruises within the G.O. Sars research vessel. The fluid inclusions data obtained from barites emphasize the fluid features characteristic of volcanogenic massive sulfide deposits, the similarities and differences for the studied hydrothermal sites, and allow comparisons with similar products from other active hydrothermal systems.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

In this work was investigated the potential of Bacillus subtilis UCP 0146 in the bioconversion of the medium containing 100% of cassava flour wastewater to obtain bioemulsifier. The evaluation of the production was carried out by the emulsification index (IE24) and surface tension (TS). The ionic charge, stability (temperature, salinity and pH measured by IE24 and viscosity), ability to remove and disperse oil and textile dye were investigated. B.subtilis produced an anionic bioemulsifier in the medium containing 100% of cassava wastewater in condition 4 of the factorial design (9% of the inoculum, at 35 °C and agitation of 100 rpm) with surface tension of 39mN/m, IE24 of 95.2 % and yield 2.69 g.L-1. Stability at different pH (2-8), temperatures (0-120ºC) and NaCl, dispersed (55.83 cm2-ODA) and reduced the viscosity of the burned engine oil (90.5 cP) , removed 94.4% petroleum and demonstrated efficiency in methylene blue removal (62.2%). The bioemulsifier and its synthesis from bacteria and also emphases on the role of surfactants in oil remediation.

To improve the monitoring of the electrical power grid it is necessary to evaluate the influence of contamination in relation to leakage current and its progression to a disruptive discharge. In this paper, insulators were tested in a saline chamber to simulate the increase of salt contamination on their surface, and to evaluate the supportability of these components. From the time series forecasting of the leakage current, it is possible to evaluate the development of the fault before a flashover occurs. Choosing which method to use is always a difficult task since some models may have higher computational effort. In this paper, for a complete evaluation, the long short-term memory (LSTM), group method of data handling (GMDH), adaptive neuro-fuzzy inference system (ANFIS), bootstrap aggregation (bagging), sequential learning (boosting), random subspace, and stacked generalization (stacking) ensemble learning models are analyzed. A review and comparison of these well-established methods for time series forecasting is performed. From the results of the best structure of the model, the hyperparameters are evaluated and the Wavelet transform is used to obtain an enhanced model.

The river Teign in Devon has come under scrutiny for failing to meet Environmental Quality Standards for ecotoxic metals due to past mining operations. A disused mine known as Bridford Barytes mine, has been found to contribute a significant source of Zn, Cd and Pb to the river. Recently, studies have been focused on the remediation of such mine sites using low-cost treatment methods to help reduce metal loads to the river downstream. Red mud is a waste product from the aluminium industry, the utilization of this resource has proven an attractive low-cost treatment method for adsorbing toxic metals. Adsorption kinetics and capacity experiments reveal metal removal efficiencies of up to 70% within the first 2 hours when red mud is applied in pelletized form. Biochar is another effective adsorbent with the potential to remove >90% Zn using agricultural feedstock. Compliance of the Teign has been investigated by analysing dissolved metal concentrations and bioavailable fractions of Zn to assess if levels are of environmental concern. By applying a Real-World Application Model, this study reveals that compressed pellets and agricultural biochar offer an effective, low-cost option to reducing metal concentrations and thus improving the quality of the river Teign.

This paper deals with the environmental characterization of a large and densely populated area, with a poor reputation for contamination, considering the contribution of environmental features (air, soil, soil hydraulic and groundwater) and the potential effects on human health. The use of Geographic Information System (GIS) has made possible a georeferenced inventory and, by overlaying environmental information, an operational synthesis of comprehensive environmental conditions. The cumulative effects on environmental features were evaluated, taking into account superposition effects, by means of the spatial multicriteria decision analysis (S-MCDA). The application of the S-MCDA for converging the combination of heterogeneous factors, related to soil, land and water, deeply studied by heterogeneous groups of experts, constitutes the novelty of the paper. The results confirmed an overall higher potential of exposure to contaminants in the environment and higher mortality rates in the study area for some tumours, but hospital admissions for tumours were generally similar to the regional trend. Besides, mortality data may be strictly dependent on the poor socioeconomic conditions, quality of therapy and a lack of welfare in the area relative to the rest of Italy. Finally, as regards the possible relationship between presence of contaminants in the environment and health conditions of the population no definite conclusions can be drawn, although the present study encourages the use of the new proposed methods, that increase the possibilities for studying the combined effect of more environmental factors.

River estuaries are dynamic and complex ecosystems influenced by various natural processes, including climatic fluctuations and anthropogenic activities. The Pearl River estuary (PRE), one of the largest in China, receives significant land-based pollutants due to its proximity to densely populated areas and urban development. This study aimed to characterize the composition, diversity, and distribution patterns of sediment microbial communities (Bacteria, Archaea, and Eukaryotes) and investigated the connection with environmental parameters within the PRE and adjacent shelf. Physicochemical conditions, such as oxygen levels, nitrogen compounds, and carbon content, were analyzed. The study found that the microbial community structure was mainly influenced by site location and core depth, which together explained approximately 67% of the variation in each kingdom. Sites and core depths varied in sediment properties such as organic matter content and redox conditions, leading to distinct microbial groups associated with specific chemical properties of the sediment, notably C/N ratio and NH4+ concentration. Despite these differences, certain dominant taxonomic groups were consistently present across all sites: Gammaproteobacteria in Bacteria; Bathyarchaeia, Nitrososphaeria, and Thermoplasmata in Archaea; and SAR in Eukaryota. The community diversity index was the highest in the bacteria kingdom, while the lowest values were observed at site P03 across the three kingdoms and were significantly different from all other sites. Overall, this study underscores the critical role of microbial communities in shaping biogeochemical processes in estuarine environments and their sensitivity to environmental changes, providing valuable information for managing and preserving the health of estuaries and coastal ecosystems.

The mining industry is known for the intense environmental impacts it triggers, especially when it is developed in an open environment. Pit lakes are formed in depleted deposits and may be promising opportunities for use by society as well as troubling environmental liabilities. While these artificial basins are increasing numerically in many parts of the world, they are still little known researchers in the Environmental Sciences, which makes their environmental management challenging. The main objective of this study was to evaluate the environmental quality of sediments from three deactivated open-pit gold mines, located in the Mara Rosa, Brazil, through chemical, ecotoxicological and genotoxicology analyses. For this purpose, we collected samples in the dry season boom, and subsequently, we analysed metals. In sequence, acute ecotoxicological and a genotoxicology test (comet assay) were developed with Danio rerio fishes, in concentrations of 3.12%; 6.25%; 12.5%; 25%; 50% and 100%, in addition to the control group. The results indicated that the three lakes are environmentally compromised, especially Lago Azul, whose waters and sediments are undergoing an intense process of geological conditioning. Our results did not verify the ecotoxicity of the sediments of any of the lakes, only behavioural alterations in the test organisms exposed to the concentrations of 25%, 50% and 100% of the samples obtained in the Lago Azul. About the sediments, DNA damage at Danio rerio was detected in the three investigated environments, although fishes kept in the water sampled at Lago Azul presented the most extension of DNA damages.

Four angucycline glycosides including three new compounds landomycin N (1), galtamycin C (2) and vineomycin D (3), and a known homologue saquayamycin B (4), along with two alkaloids 1-acetyl-β-carboline (5) and indole-3-acetic acid (6), were identified from the fermentation broth of an intertidal sediments derived Streptomyces sp. Their structures were mainly established by IR, HR-ESI-MS, 1D and 2D NMR techniques. Among the isolated angucyclines, saquayamycin B displayed potent cytotoxic activity against hepatoma carcinoma cells HepG-2, SMMC-7721 and plc-prf-5, with IC50 values 0.135, 0.033 and 0.244 μM respectively, superior to positive drug doxorubicin. Saquayamycin B treatment to SMMC-7721 cells led to the typical morphological signs of apoptosis in 4',6-diamidino-2-phenylindole (DAPI) staining experiment.

Native strains of Trichoderma, isolated from mangrove sediments of PE, Brazil were determining their morphological and molecular characterization, and were investigated to assess of their biocontrol potential over the phytopathogenic Fusarium strains isolated from Caatinga soil, PE, Brazil. The Trichoderma strains were characterized by polyphasic approach, which combined their morphological characteristics, macro- and microculture results, growth evaluation by Tukey test, with significance of 5%. The DNA was extracted and the product was amplified with primers ITS 1 and 2, and sequenced. Trichoderma strains were compatible morphologically with the description of the genus. The molecular identification of Trichoderma, sequences of 500 bp were amplified, deposited in GenBank and used for phylogenetic analysis. The growth rate analysis showed rate of 0.1207 cm^h-1 to Trichoderma strains and Fusarium spp. lower growth rate (0.031 cm^h-1) was observed. The antibiosis tests showed the best antagonistic level of effectiveness to T. asperellum UCP 0149 against F. solani UCP 1395(82.2%) and F. solani UCP 1075(70.0%), followed of T. asperellum UCP 0319 against F. solani UCP1083 (73.4%), and T. asperellum UCP 0168 against F. solani UCP1098 (71.5%), respectively. The data obtained could serve as the basis for developing several biotechnological processes of safe use.

Nutrient release from marine sediments in Osaka Bay has a significant impact on nutrient concentrations in seawater. A tsunami induced by the Nankai Trough earthquake may disturb marine sediments in the inner part of Osaka Bay. An incubation experiment to estimate the release rates of NH4-N and PO4-P was conducted to understand the present conditions and to quantify the changes caused by tsunamis. Two types of cores were created: a "control core" representing the current sediment, and a "redeposition core" representing the redeposition after the tsunami. The release rates have been decreasing since the year 2000 and have remained low. The experimental results suggest that the release rate after exposure to an aerobic environment by a tsunami may decrease to approximately 70% for NH4-N and 60% for PO4-P of the current level. In the past, the release rates were values experienced in the inner part of Osaka Bay. However, the reduction in the release rate by tsunamis may be more limiting for primary production under the current situation where the contribution of release for nutrients in seawater is significant.

In view of increasing concerns over non-renewable resource depletion and waste management, this study aimed to apply the Taguchi optimization technique to determine the process conditions for producing bricks by incorporating thin film transition liquid crystal displays (TFT-LCD) waste glass powder with reservoir sediments. An orthogonal array L₁₆(4⁵) was adopted, which consisted of five controllable four-level factors (i.e., cullet content, drying method, preheat time, sintering temperature, and error). Moreover, the analysis of variance method was used to explore the effects of the experimental factors on the density, water absorption, shrinkage ratio, loss of ignition, porosity, and compressive strength of the fired bricks. The microstructures of the fired specimens were investigated by scanning electron microscopy. Then, the large-scale production techniques for fired bricks containing recycled TFT-LCD glass cullet and reservoir sediments was developed in a commercially available tunnel kiln. The test results showed that the structure of fired specimen was loose at a sintering temperature ranged from 900–950 °C. However, the fired specimen showed a significant densification at the sintering temperature of 1050 °C. In addition, Taguchi method is a feasible approach for optimizing process condition of brick using recycled TFT-LCD glass cullet and reservoir sediments and it significantly reduces the number of tests. On the other hand, the characteristics of fired bricks developed in the tunnel kiln were in compliance with Chinese National Standards class Ι building bricks criteria.

Carbon and nitrogen contents and their isotopic components and AMS radiocarbon dating ages were measured for 57 coastal sediments from Weizhou Island to analyze the distribution of total inorganic carbon (TIC) and its carbon and oxygen isotopic components (δ13Ccarb and δ18Ocarb), total organic carbon (TOC) and total nitrogen (TN) contents and their stable isotopic components (δ13CTOC and δ15NTN) and environmental significance. The results showed that the oldest age of coastal sediments on Weizhou Island was 2750 cal. a BP, and the average TIC contents of A1, A2, B1, C1, and D1 in the intertidal zone were all greater than 5%, where δ13Ccarb and δ18Ocarb were enriched, while the TIC contents in A3, C2, and D2 of the supra-tidal zone were low, where δ13Ccarb and δ18Ocarb were depleted. Moreover, TIC decreased sharply from the estuary to upstream region in the C1-C2 section. The average C/N ratio was 7.02, and δ13CTOC and δ15NTN were between -14.96‰~-27.26‰ and -14.38‰~4.12‰, respectively. These measurements indicated that the TIC in coastal sediments mainly came from seawater. A1, A2, and B1 in the northern intertidal zone exhibited organic terrestrial signals because of C3 and C4 plant inputs, which proved that the important source of the northern coast of Weizhou Island came from the island. The lacustrine facies deposits were mainly distributed in the upper reaches of the river, the northern coastline was rapidly advancing toward the sea, and part of the southwestern coastal sediments rapidly accumulated to the shore under the influence of a storm surge. The relative sea level of the Weizhou Island area has continuously declined at a rate of approximately 2.07 mm/a, using beach rock as a marker, since the Holocene.

Forest vegetation plays a key role in the cycling of mercury (Hg) and organic matter (OM) in terrestrial ecosystems. Litterfall has been indicated as the major transport vector of atmospheric Hg to forest soils, which is eventually transported and stored in the sediments of forest lakes. Hence, it is important to understand how changes in forest vegetation affect Hg in soil and its biogeochemical cycling in lake systems. We investigated the pollen records and the geochemical compositions of sediments from two lakes (Schurmsee and Glaswaldsee) in the Black Forest (Germany) to evaluate whether long-term shifts in forest vegetation induced by climate or land use influenced Hg accumulation in the lakes. We were particularly interested to determine whether coniferous forests were associated with a larger export of Hg to aquatic systems than deciduous forests. Principal components analysis followed by principal component regression enabled us to describe the evolution of the weight of the latent processes determining the accumulation of Hg over time. Our results emphasize that the in-lake uptake of Hg during warm climate periods, soil erosion after deforestation and emissions from mining and other human activities triggered changes in Hg accumulation during the Holocene stronger than the changes caused by forest vegetation alone.

The immobilisation of bacteria on biochar has shown potential for enhanced remediation of petroleum hydrocarbon-contaminated soil. However, there is a lack of knowledge on the effect of bacterial immobilisation on biosolids-derived biochar for the remediation of diesel-contaminated soil. The aim of this current study was to assess the impact of the immobilisation on biosolids-derived biochar of an autochthonous hydrocarbonoclastic bacteria, Ochrobacterium sp. (BIB) on the remediation of diesel-contaminated soil using a laboratory based mesocosm study. Additionally, the effect of fertiliser application on the efficacy of the BIB treatment was investigated. Biochar (BC) application alone led to significantly higher hydrocarbon removal compared to the control treatment at all sampling times (4,887 – 11,589 mg/kg higher). When Ochrobacterium sp. was immobilised on biochar (BIB), the hydrocarbon removal was higher than BC by 5,533 mg/kg and 1,607 mg/kg at weeks 10 and 22, respectively. However, when BIB was co-applied with fertiliser (BIBF), the hydrocarbon removal was lower than BIB by 6,987 – 11,767 mg/kg. Quantitative PCR analysis revealed that the gene related to Ochrobacterium sp. was higher in BIB than in the BC treatment, which likely contributed to higher hydrocarbon removal in the BIB treatment. The findings of this study demonstrate that bacteria immobilisation on biosolids-derived biochar is a promising technique for the remediation of diesel-contaminated soil. Future studies should focus on optimising the immobilisation process for enhanced hydrocarbon removal.

A wide variety of pump and treat methods like chemical precipitation, adsorption, ion exchange and reverse osmosis have been trialled for many decades for fluoride removal from groundwater, but the problem of fluoride contaminated water remains in many parts of the world largely because these processes require constant monitoring, are expensive to implement and maintain at decentralised scale due to lack of reticulation infrastructure, and possess sludge disposal problem. This paper presents an overview of various fluoride removal processes and the limitations associated with each process and the application of in-situ permeable reactive barrier for remediating fluoride contaminated groundwater is explored, which displays the potential to be a cost effective, low maintenance and energy intensive technology.

The corrosion behavior of Fe-containing directionally solidified (DS) and centrifugally cast (CC) Al-Si-Cu-Zn alloys with either Co or Ni additions has been investigated. Electrochemical and immersion corrosion methods were used to investigate the corrosion behavior in 0.6 M NaCl after short (1-hour) and long (30-day) exposure periods. The employed solidification methods allowed the production of samples with a wide range of secondary dendrite arm spacing (SDAS) while preserving Si and Fe-containing phases. The 0.5 wt.% Ni and Co additions led to the growth of the AlFeSi(Ni) and AlFeSi(Co) phases, but no binary AlNi nor AlCo intermetallic par-ticles have been generated. Potentiodynamic polarization studies at early exposure revealed an increase in the corrosion potential as the Ni was added for either fast or slow solidified samples. The electrochemical impedance spectroscopy at early exposure demonstrated that the Ni-modified alloy, on the other hand, was associated to smaller charge transfer resistances, in-dicating a reduction in corrosion resistance after short elapsed time into the electrolyte. Howev-er, 30-day immersion tests revealed much lower corrosion rate of the Ni-modified alloy than the other alloys, while the corrosion rates of the Co-modified and non-modified alloys were simi-lar. In the Ni-containing alloy, decreased corrosion rate under long-term corrosion process was attributed to the formation of a thick and dense alumina layer, effectively protecting the surface under such conditions. This work contributes to a better knowledge of the corrosion behavior of Ni- and Co-corrected Al industrial scrap compositions.

The benthic matrix acts as a key natural archive where the memory of long-term timescale environmental changes is recorded. Some ecological and chemical features of fjord sediments were explored during the AREX cruise carried out in the Svalbard archipelago in summer 2021. The activity rates of the enzymes leucine aminopeptidase (LAP), beta-glucosidase (GLU) and alkaline phosphatase (AP) and community-level physiological profiles (CLPP) were studied with the aim of determining the functional diversity of the benthic microbial community, while bacterial isolates were screened for their susceptibility to antibiotic molecules in order to explore the role of these extreme environments as potential reservoirs of antibiotic resistance. Enzyme activity rates were obtained by fluorogenic substrates, CLPP by Biolog Ecoplates; antibiotic susceptibility assays were performed through the standard disk diffusion method. Spatial trends observed in the functional profiles of the microbial community suggested the variability in the microbial community composition, presumably related to the patchy distribution of organic substrates. Complex Carbon sources, carbohydrates and amino acids were the organic polymers preferentially metabolized by the microbial community. Multiple resistance to ampicillin, clindamycin and gentamycin was detected in all the sampled sediments, excepting in the southern Hornsund area, stressing the role of sediments as a potential reservoir of chemical wastes ascribable to antibiotic residuals. This study provides new insights on the health status of fjord sediments of West Spitsbergen applying a dual ecological and biochemical approach. Microbial communities in the fjord sediments showed globally a good functional diversity, suggesting their versatility to rapidly react to changing conditions.

CO2 emissions resulting from the production of cement is a major issue, but can be limited by the partial substitution of cement by low-carbon-impact additions. The aim of this study was the formulation of a ternary binder based on ordinary Portland cement (OPC), ground granulated blast-furnace slag (GGBS) and flash-calcined sediment (FCS), a dredged waste which was valorized after applying a new heat treatment: flash calcination. The used materials were physically, chemically and mineralogically characterized. The composition of the formulations was optimized using mixture designs. Five formulations, one reference formulation RM (100% OPC), one binary formulation (50% OPC/50% GGBS), and three ternary formulations with a variable FCS rate (10%, 15%, 20%), were selected and characterized fresh and hardened. Results showed that the incorporation of FCS reduced the workability and increased the density. In addition, a decrease in the initial setting time and the heat of hydration peak were observed. In the hardened state, the formulation containing 10% FCS showed 90-day mechanical strengths superior to that of RM. The use of FCS in ternary binders could reduce the environmental impact by reducing greenhouse gas emissions.

This study investigated the presence of human Norovirus (HuNoV) by genotype in 1,486 groundwater samples, collected from 843 groundwater wells suspected of contamination during 2007-2016, in Republic of Korea. We identified and genotyped 186 HuNoV sequences in 178 HuNoV-positive samples using the RIVM-NoroNet norovirus genotyping tool (NGT) and phylogenetic tree analysis based on RIVM-NoroNet reference sequences. HuNoV GII was more prevalent than GI. The major genotypes detected were HuNoV GII.4 (43.0%), GII.22 (15.6%), GI.5 (10.2%) and GI.1 (8.6%); 14 genotypes accounted for < 5.0%. Increasing HuNoV GII.17 has displayed a worldwide trend, including in Europe and Asia since 2010, and it was the dominant HuNoV genotype during 2013-2014 in Korea. However, HuNoV GII.4 was the major genotype detected in groundwater in Korea in 2015-2016, and it is becoming increasingly prevalent similar to HuNoV GII.17.

River sediment from two inflow watersheds (Hongze and Tiaoxi) to Hongze and Taihu Lake in Eastern China was analyzed by the sequential extraction procedure. This study aimed to explore a spatial distribution of phosphorus fractions in river sediments and analysed the relationship between different phosphorus fractions and their environmental influence on the sediments within different watersheds in Eastern China. Five fractions of sedimentary phosphorus, including freely sorbed phosphorus, were all analyzed (NH₄Cl-P), redox-sensitive phosphorus (BD-P), bound phosphorus metal oxide (NaOH-P), bound phosphorus calcium (HCl-P) and residual phosphorus (Res-P). The order of rank of the P fractions for the river Anhe was HCl-P>NaOH-P>BD-P>NH₄Cl-P; whereas that of the Suihe river was HCl-P>BD-P>NaOH-P>NH₄Cl-P. For the rank order of the Hongze watershed, HCl-P was higher while the NH₄Cl-P contents were significantly lower. The rank order for the Dongtiaoxi river was NaOH-P > HCl-P> BD-P> NH₄Cl-P and that of Xitiaoxi river was NaOH-P> BD-P> HCl-P> NH₄Cl-P. Compared with phosphorus forms of Tiaoxi watershed, NaOH-P contents were significantly higher in the converse of HCl-P contents were significantly higher in Hongze watershed while both in NH₄Cl-P contents were significantly lower. Variations may be attributed to differential discharge of P watershed form due to land-use changes and urban river ambient conditions.

In eutrophic waters, such as Mikawa Bay, Japan, anoxic bottom water develops in summer. This causes sulfide release into seawater by sulfate reduction in the sediment, leading to environmental problems. The addition of iron to sediments is a method used to improve the sediment environment, which was devised from a natural phenomenon. However, this method has not yet been quantitatively evaluated. In this study, we aim to quantitatively evaluate the suppressive effect of iron on sulfide release. First, we develop a sediment model that focuses on S and Fe. We then attempted to reproduce the observations and experiments on sulfide dynamics using the model. Consequently, the proposed model was able to reproduce field sulfur and Fe dynamics in sediments. Additionally, the model described the characteristics of sulfide release considering the effects of additive iron materials. Finally, we conducted predictive calculations and quantitatively evaluated the effects of adding iron materials to the sediments in terms of sulfur and iron cycles.

The City of Meycauayan is considered as one of the most polluted cities in the developing world on the account of industrial discharges of toxic materials to the environment. This work investigated the sources of the heavy metal pollution by analyzing soil and sediment samples for heavy metals (Cr, Hg, Ni, and Pb) together with selected environmental indicators (TN, TOM, and TP) located along the Meycauayan River. Hierarchical cluster analysis (HCA), principal components analysis (PCA), and Pearson correlation analysis (CA) were used to identify the sources of the metals. Results showed delineated locations of severe levels of heavy metal pollution downstream because of the concentration of industrial activities. Cr contributed more than any other heavy metals analyzed due to proliferation of tanneries discharging untreated wastewaters to the river. Significant inputs of Pb and Hg from Pb-acid battery recycling and gold smelting industries were also found. Risk assessments indicated severe levels of heavy metal pollution where industrial activities are concentrated. The mean Cr, Pb, Ni, and Hg in the sampling locations have mean incidences of toxicity of 91.7 %, 53.6 %, 27.7 %, and 70.0 %, respectively. Our study showed a serious need to address heavy metal pollution in Meycauayan.

Novel functionalized and/or grafted crosslinked chitosan adsorbents were synthesized and used to remove several toxic heavy metal ions from contaminated water efficiently and selectively. The chitosan biopolymer was functionalized by maleic anhydride (CS_MA), which also acted as a crosslinking agent. Separately, Glutaraldehyde-crosslinked chitosan (CS_GA) was grafted with poly(methyl methacrylate) (CS_MMA). The synthesized adsorbents were used to adsorb and remove heavy metal ions from contaminated water. The metal ions were nickel, lead, chromium, and cadmium. The adsorption capacity of the adsorbents was analyzed under various conditions of contact time, adsorbent dose, initial concertation, temperature, and pH and evaluated against those of pure chitosan (CS) and the crosslinked one (CS_GA). The ultimate conditions for the ions removal were 0.5g/100ml adsorbent dose, an initial metal ion concentration of 50 ppm, a temperature of 45oC, and a pH 9. CS_MMA, which had the highest removal percentages for all metal ions, ranging from 92% to 94%. The adsorption was demonstrated to fit a pseudo-first-order model that followed a Langmuir adsorption isotherm. The results highlight the capacity of the synthesized polymers to efficiently remove major toxic contaminants at low cost from contaminated water, present especially in low-income areas, without harming the environment.

Urination on carpet and subflooring can develop into persistent and challenging to mitigate odor. Very little or no information is published on how these VOCs change over time when urine is deposited on the carpet covering a plywood-type subflooring. This research has investigated the VOCs emitted from carpet+subflooring (control), carpet+subflooring sprayed with water (control with moisture), and cat urine-contaminated carpet+subflooring (treatment) over time (day 0 and 15). In addition, the effect of popular cleaning products on VOCs emitted and evaluated their efficacy in eliminating those indoor odors over time (day 0 and 15). Carpet-subflooring with all treatments were also contaminated with Micrococcus luteus, nonmotile obligate aerobe commonly found in household dust, to observe the impact of the aerobe on carpet-subflooring VOCs emission. VOCs emitted from carpet+subflooring receiving different treatments were collected from headspace using solid-phase microextraction (SPME). The VOCs were analyzed using a multidimensional gas chromatography-mass spectrometer attached to an olfactometry (GC-MS-O). Many common VOCs were released from the carpet on day one and day fifteen, specifically from urine contamination. Cleaning products were effective in masking several potent odors of cat urine contaminated carpet VOCs on day one but unable to remove the odor appeared on day 15 in most cases.

This study aimed to assess the presence of metal contamination in the sediments of the Narmada River by considering seasonal variations. In this context, samples were gathered from six stations along the river in 2021–22. To assess the various metals including Li, Na, Mg, Al, Ca, Fe, Cu, Zn, Co, and Ni by utilizing ICP-MS. Sediment contamination was assessed by utilizing indices like contamination factor (CF), pollution load index (PLI), geo-accumulation factor (Igeo), and enrichment factor (EF). The observed order of metals concentration revealed that metals Fe>Al>Mg>Ca>Na>Cu>Zn>Co>Ni>Li. The seasonal variation reveals metals Al, Fe, Cu, Zn, and Ni exhibit the highest concentrations during the monsoon and metals Li and Co, the highest concentration in the post-monsoon, while metals Na, Mg, and Ca, exhibit their peak concentration during the pre-monsoon. The findings from CF, PLI, Igeo, and EF indicate that there were low to moderate contaminations, metal pollution exists, uncontaminated to moderate contaminations, and minor enrichment. The cluster analysis revealed the source of contamination was anthropogenic, marine, and fertilizer activities. Additionally, Correlation matrix was employed to establish connections between metals. The findings of this research are to understand the metal contamination and potential carcinogenicity in the sediment of Narmada River.

Estuaries are excellent environments of identifying pollution episodes that have affected river basins, as their sediments are the final destination of some of the pollutants. This paper studies the geochemical evolution of five elements (As, Co, Cu, Pb, Zn) in a core extracted from the middle estuary of the Tinto River (SW Spain). Results are based on facies interpretation, ICP Atomic Emission Spectrometry analysis, the application of a regional background to obtain the geoaccumulation index and dating. Four pollution episodes have been detected at ~5.8 cal. kyr BP (acid mine drainage?), 4.7-4.5 kyr BP (first mining activities), the 1850-1960 interval (intensive mining) and the second half of the 20th century (intensive mining and industrial inputs). All episodes show an increase in one or more of these elements, as well as changes in their geochemical classes deduced from the geoaccumulation index.

The remediation of dredged marine sediments contaminated by heavy metals has drawn increasing attention worldly. The immobilization was regarded as a promising method to reduce adverse impacts on marine ecosystem. In this study, kaolinite and limestone were used as amendments to immobilize heavy metals (e.g. Zn, Pb and Cu) respectively in dredged marine sediments collected from the coastal zone adjacent to Tianjin Port in Bohai Bay. The sequential extraction procedure was applied to identify the mobility of heavy metals and further to evaluate the immobilization effect of amendments. The physical-chemical properties of sediments, such as pH, electrical conductivity (EC), salinity, and total organic carbon (TOC), were also measured to better understand their influence on heavy metals’ mobility. In addition, the compositions of clay minerals were also analyzed to identify the transformation process of minerals in the sediments. The results of sequential extraction procedure indicated that mobile fractions of heavy metals were converted into relatively stable fractions because of the two amendments. In addition, EC, salinity and TOC decreased moderately while no obvious variations of pH in the sediments were observed with the addition of the the kaolinite and the limestone. The percentage of montmorillonite decreased to minimum value while that of chlorite increased gradually during the experimental periods for 40 days probably due to complexation reaction. It was confirmed that both kaolinite and limestone can effectively reduce the mobility and bioavailability of heavy metals, particularly for Zn, generally, limestone has a better immobilization effect compared with kaolinite.

Major marine construction projects, resulting in the release of sediments, are subject to environmental assessment and other regulatory approval processes. An important tool used for this is the development of specialized numerical methods for these marine activities. An integrated set of numerical methods addresses four distinct topics: the near-field release and mixing of suspended sediments into the water column (i.e. the initial dilution zone); the transport of the suspended sediments under the influence of complex ocean currents in the far-field; the settling of the transported suspended sediments onto the seabed; and the potential for resuspension of the deposited sediments due to sporadic occurrences of unusually large near-bottom currents. A review of projects subjected to environmental assessment in the coastal waters of British Columbia from the year 2006 to 2017, is presented to illustrate the numerical models being used and their ongoing development. Improvements include higher resolution model grids to better represent the near-field, the depiction of particle size dependent vertical settling rates and the computation of resuspension of initially deposited sediments, especially in relation to temporary subsea piles of sediments arising from trenching for marine pipelines. The ongoing challenges for this numerical modeling application area are also identified.

The presence of harmful algal blooms (HABs) and cyanotoxins in drinking water sources poses a great threat to human health. The current study employed molecular techniques to determine the occurrence of non-toxic and toxic cyanobacteria species in the Limpopo River basin based on the phylogenetic analyses of 16S rRNA gene. The bottom sediments samples were collected from selected rivers: Limpopo, Crocodile, Mokolo, Mogalakwena, Nzhelele, Lephalale, Sand Rivers (South Africa); Notwane (Botswana), Shashe River and Mzingwane River (Zimbabwe). The physical-chemical analysis of the bottom sediments showed the availability of nutrients, nitrates and phosphates, in excess of 0.5 mg/l for most of river sediments, alkaline pH and salinity in excess of 500 mg/l. The FlowCam showed the dominant cyanobacteria species identified from the samples were Microcystis species, followed by Cylindrospermopsis raciborskii, Phormidium and Planktothrix species and this was confirmed by molecular techniques. Nevertheless, two samples showed the amplification of cylindrospermopsin polyketide synthetase gene (S3 and S9) while two samples showed amplification for microcystin/nodularin synthetase gene (S8 and S13). Thus these findings may imply the presence of toxic cyanobacteria species in the river sediments. The presence of cyanobacteria may be hazardous to human because rural communities and farmers who abstract water from Limpopo river catchment for human consumption, livestock and wildlife watering and irrigation.

Amyotrophic lateral sclerosis (ALS) disease clusters are found in several countries worldwide. In the United States, ALS clusters are found in many states, largely within the northern United States. The cause of the increased rates of ALS in these areas remains indefinite. It is reported here that many ALS clusters are associated with sites of current or prior glacial lakes, or regions containing an abundance of silts and clay minerals. The potential significance of these findings in ALS is discussed.

Sulfur contamination of topsoil, spatial distribution of contamination and surface water chemistry were investigated on an area of over 200 ha of a new forest ecosystem. Common birch and Scots pine growth reaction, vitality and nutrients supply, as well as wood small-reed (Calamagrostis epigejos (L.) Roth) chemical composition were assayed. The chemistry dynamics of soil leaching and the sulfur load leached from the sulfur contaminated soil-substrates were analyzed. The remediation effect of the birch and pine litter was assayed in an experiment under controlled conditions. It was found that reclamation was effective in a majority of the post-mining site, however hot-spots with sulfur contamination reaching even 45,000 mg kg-1, pH <2.0, and EC 6,500 µS cm-1 were reported. Surface waters typically displayed elevated concentrations of sulfate ions (average 935.13 mg L-1), calcium ions (up to 434 mg L-1) and high EC (average 1.795 µS cm-1), which was connected both with sulfur contamination and sludge lime used in neutralization. Wood small-reed was found to be species adapting well to the conditions of elevated soil salinity and sulfur concentration. We noted that an addition of organic matter had a significant impact on the chemistry of soil solutions but did not indicate in short term experiment a remediation effect by increased sulfur leaching.

The oil spilled from the Gulf war caused land pollution and various petroleum compounds. Among petroleum compounds, polycyclic aromatic hydrocarbons (PAHs) are known for toxicity, and have been designated as carcinogenic, mutagenic, and endocrine disrupting substances by the United States Environmental Protection Agency (USEPA). According to the USEPA, toxic equivalents quotient (TEQ), and mutagenic equivalents quotient (MEQ) can be calculated by multiplying the toxic equivalency factor (TEF) and mutagenic equivalency factor (MEF) by the concentration of PAHs. The USEPA calculates the relative TEF for other PAHs by setting the TEF value of benzo(a)pyrene, which is highly toxic, to 1. Relative MEF is also calculated in the same way. In this study, the TPH concentrations of crude oil-contaminated soils collected from the Burgan in Kuwait were measured to be 5, 8, and 20% and TEQ and MEQ of the soils were calculated by multiplying the 16 PAHs concentrations measured for each sample by TEF and MEF, respectively. When the TPH concentration was increased by 4 times from 5% to 20%, the TEQ was increased by about 9 times and the MEQ was increased by about 10 times. Therefore, it was concluded that as the TPH concentration increases, the carcinogenicity and mutation rate increase greatly. In addition, ecotoxicity assessment was performed using luminescent bacteria to compare the relationship between the calculated TEQ and MEQ and actual ecotoxicity, and benzo(a)pyrene among 16 PAHs showed a coefficient of determination of 0.95. In this study, ecotoxicity in PAHs-contaminated environment can be estimated by analyzing benzo(a)pyrene as a representative substance.

The combination of organic matter, iron oxide, and clay minerals is of great significance for the adsorption of copper ions (Cu). The purpose of this study is to explore the characteristics of Cu adsorption and laws governing Cu complexation to organic–inorganic, organic–clay mineral, and iron-oxide–clay mineral complexes in the sediments in the estuary of plateau fault and sinking lake——Dianchi Lake. In this study, Cu adsorption tests were performed on the three complexes, in order to study the kinetic behavior of adsorption, Langmuir and Freundlich isotherm models were used. The samples before and after adsorption were characterized via scanning electron microscope (SEM), Fourier infrared spectroscopy (FTIR), and X-ray diffraction (XRD). Our results show that, the Freundlich isotherm models model was able to describe adsorbent behavior in comparison to the Langmuir models. During the Cu adsorption process, the iron-oxide–clay mineral complex is able to adsorb Cu, via coordination exchange, through the –OH contained therein. Organic-matter–clay mineral complexes bonded to the surfaces of clay minerals by replacing the hydroxyl groups with functional groups (carboxyl groups or phenolic hydroxyl groups) contained in the organic matter. Organic–inorganic composites then adsorbed Cu through the coordination exchange of –OH in the polar functional groups of alcohols, phenols, and carboxylic acids. The adsorption capacity of Cu in these three sediment complexes was observed to have the following order: organic–inorganic complex &gt; organic-matter–clay mineral complex &gt; iron-oxide–clay mineral complex. The semi-quantitative analysis results of Fourier Infrared Spectroscopy show that the organic matter (changes in the peak area of functional groups such as carboxyl groups) in the organic-inorganic composite material has an important effect on the amount of copper ions adsorbed by clay minerals.

Microplastics (MPs) quantification in benthic marine sediments is typically performed by time-consuming and moderately accurate mechanical separation and microscopy detection. In this paper we describe the results of our innovative Polymer Identification and Specific Analysis (PISA) of microplastic total mass, previously tested on either less complex sandy beach sediment or less demanding (because of the high MPs content) wastewater treatment plant sludges, applied to the analysis of benthic sediments from a sublittoral area north-west of Leghorn (Tuscany, Italy). Samples were collected from two shallow sites characterized by coarse debris in a mixed seabed of Posidonia oceanica, and by a very fine silty-organogenic sediment, respectively. After sieving at &lt;2 mm the sediment was sequentially extracted with selective organic solvents and the two polymer classes polystyrene (PS) and polyolefins (PE and PP) were quantified by pyrolysis-GC/MS. A contamination in the 8-65 ppm range by PS could be accurately detected. Acid hydrolysis on the extracted residue to achieve total depolymerization of all natural and synthetic polyamides, tagging of all aminated species in the hydrolyzate with a fluorophore, and reversed-phase HPLC (RP-HPLC) analysis, allowed to quantify within the 137-1523 ppm range the individual mass of contaminating Nylon 6 and Nylon 6,6, based on the detected amounts of the respective monomeric amines 6-aminohexanoic acid (AHA) and hexanediamine (HMDA). Finally, alkaline hydrolysis of the residue from acid hydrolysis followed by RP-HPLC analysis of the purified hydrolysate showed contamination by polyethylene terephthalate (PET) in the 12.1-2.7 ppm range, based on the content of its comonomer, terephthalic acid.

The genus Amphichorda has been recently re-erected as an independent linage from Beauveria, circumscribed within Cordycipitaceae. However, its phylogenetic relationships with other members of this family remain obscure. In our on-going efforts to expand the knowledge on the diversity of culturable ascomycetes from the Mediterranean Sea, we isolated several specimens of Amphichorda. Preliminary sequence analyses revealed great phylogenetic distance with accepted Amphichorda species and a close relation to Onychophora coprophila. Onychophora is a monotypic genus of enteroblastic conidiogenous cells, presumably related to Acremonium (Bionectriaceae); while Amphichorda exhibits holoblastic conidiogenesis. Here, we examine representative strains of Amphichorda species to resolve the taxonomy of the genus and the above-mentioned fungi combining morphological, ultrastructure and multi-locus phylogenetic analyses (ITS, LSU, tef1, BenA). The results revealed Amphichorda as a member of the Bionectriaceae, where its asexual morphs represent a transition between enteroblastic and holoblastic conidiogenesis for this group of fungi. We also describe and illustrate Amphichorda littoralis sp. nov., and propose the new combination Amphichorda coprophila. In addition, we stablish key phenotypic features to distinguish Amphichorda species and demonstrate the higher salt tolerance degree of A. littoralis, consistent with its marine origin. This work provides a comprehensive framework for future studies in the genus.

The detrimental consequences of soil pollution caused by crude oil or petroleum products are immense, leading to land degradation, property damage, and rendering agricultural practices ineffective. Extensive research has been conducted in the field of soil remediation, but further studies are still required to explore additional details of the remedial process. As a result, this study focuses on evaluating the effectiveness of Vernonia Galamensis and Vernonia Amygdalina, commonly known as bitter leaf, in remediating hydrocarbon-contaminated soil. In the analysis of micro-organisms, it was found that the bitter leaf extracts contained three types of bacteria: Pseudomonas aeruginosa, Staphylococcus aureus, and Escherichia coli. The leaf extracts were prepared using different methods, including sun drying, room drying, and using them in their wet form, which were then blended into the contaminated soil. The study also took into consideration three different types of soil: sandy-loamy soil, clay soil, and swamp soil. These advanced techniques and considerations are relevant to the topic of revolutionizing soil remediation, as they explore the potential of bitter leaf extracts and different soil types in effectively mitigating the effects of hydrocarbon contamination.The findings revealed that the wet blended extracts of Vernonia performed exceptionally well in the remediation process, surpassing a 50% reduction in the initial contamination levels. The study involved utilizing a quantity of bitter leaf ranging from 10g to 40g, which was added to the contaminated soils and monitored for a duration of 40 days. Remarkably, this approach led to a significant decrease in the concentration of contaminants within the soil, indicating the effectiveness of the bitter leaf extracts in the remediation process. Towards the conclusion of the study, predictive models were constructed to forecast the impact of hydrocarbon content, as well as the levels of lead, zinc, and chromium in the soil. These variables served as the dependent variables in the models, while the mass of bitter leaf, the duration of treatment, and the pH of the soil were considered as independent variables. Significantly, the models achieved a level of significance of less than 0.05, indicating their statistical validity. Furthermore, the r2 value, which represents the goodness of fit, demonstrated an appreciable level of accuracy in predicting the remediation effects. These results highlight the potential of the developed models in assessing and predicting the remedial outcomes of hydrocarbon contamination using bitter leaf extract.

Globally, open-pit coal mining is associated with severe land use impact and contamination of soil and water resources with heavy metals. Thus, in growing economies like India, where coal is a significant energy source, the heavy metals contamination of soil and water become ubiquitous. Remediation of such a large stretch of mined-out land is a major challenge and a costly process for the mining industry. In recent years, the application of biochar for the remediation of such heavy metals-contaminated soil has been widely practiced. However, applying biochar and cultivating plants in field conditions becomes challenging. This study uses a unique remediation approach by developing biochar-bentonite-based seed balls encapsulating Shorgham grass seeds at their core for application in the contaminated soil. The seed ball was developed by using the bentonite biochar composite in varying weight fractions of 0.5 – 5 % with respect to the kaolinite, whose fractions in the seed ball also varied at one, three, and five parts. The seed balls were applied to the pots containing 3 kg of heavy metals contaminated soil for a pot-culture study in a polyhouse for a period of four months. Initial soil analysis results indicated that the mine soil samples showed poor nutrient and organic matter content and were contaminated with heavy metals such as Ni, Zn, Cr, and Cd. Post-pot-culture soil analysis results indicated that the application of seed balls containing five fractions of biochar composite with its combination with three and five-weight fractions of kaolinite showed substantial improvement in the pH, available nutrients, organic matter content, soil enzymes, and overall soil fertility index compared to the controlled study and other cases. The same combination of seed balls also significantly reduced the plant-available fractions of Ni, Zn, Cr, and Cd in the soil and the translocation of these heavy metals from the rhizosphere zone to the grass’s aerial parts, indicating stabilization of heavy metals within the soil matrix. Moreover, the application of seed balls also substantially improved the plant physiology and reduced the release of stress hormones such as proline and glutathione within the plant cells indicating improvement in the plant’s biotic and abiotic stress factors. Thus, the application of seed balls in heavy metals contaminated soils, particularly over a large stretch of land, could be a low-cost and viable remediation technique.

Dredging is a common technique for managing eutrophication problems in waters, reducing the accumulation of pollutants by removing sediments from the bottom of water bodies. However, dredging can cause complex impacts on lake ecosystems, and it is crucial to understand benefits and mechanisms for environments. In this paper, the dredged and undredged areas in the Caohai portion of Dianchi Lake were studied to analyze the effects of dredging on nitrogen-phosphorus transport and conversion and changes in nitrogen-phosphorus morphology content and its mechanisms by comparing the nitrogen-phosphorus morphology content, percentage; nitro-gen-phosphorus ratio, and release contribution of the two areas. It was found that the ratio of sta-bilized nitrogen (SN) to stabilized phosphorus (SP) in the dredged area was lower than that in the non-dredged area; the BD-P and TOC contents had a large turnaround at the 16-20 cm position of the sediment in the dredged area; and the main conclusions were that the dredging would disrupt the internal equilibrium of the lake system for many years, and in particular, it would have the greatest effect on the balance of the BD-P in the phosphorus forms of the sediment, and that the column cores of the dredged area from 0 to 16 cm might be newly accumulated sediments after the dredging project. However, with time, the distribution of nitrogen and phosphorus forms in the newly accumulated sediments will gradually reach a new equilibrium. In addition, dredging will also cause significant changes in the retention efficiency of nitrogen and phosphorus in the sediment, and the stable nitrogen and phosphorus forms will be released and transformed into unstable ni-trogen and phosphorus forms.

This study examined the spatial-temporal distribution of sulfur and iron compounds (dissolved sulfide, iron sulfide, and ionized iron) in sediments from April 2015 to March 2016 at four stations in Mikawa Bay, Japan. Seasonal changes were observed in dissolved sulfide, iron sulfide, and ionized iron in the upper part of the sediment (0–4 cm depth) at all stations. The maximum concentration in the upper part of the central bay was 2.8 mmol L-1. The maximum values of dissolved sulfide (ranging from 1.4 to 8.1 mmol L-1) at stations located in a water way varied among stations. The iron sulfide concentration in the upper part of the sediment at a station where dissolved sulfide concentration in the waterway was relatively low exceeded that at other stations in the waterway during spring to summer. Ionized iron concentration was highest at the station where the dissolved sulfide concentration was low. The study results suggest that iron plays an important role in determining the magnitude of dissolved sulfide accumulation in sediments by binding with dissolved sulfide. The results imply the possibility of mitigating the accumulation of free sulfides, which causes extreme hypoxia, by artificially adding sufficient iron to the seabed.

The increasing use of chemicals requires a better understanding of their presence and their dynamics in the environment as well as their impact on ecosystems; it is therefore important to set up procedures. The aim of this study was to validate the first steps of an innovative multi-omics approach based on metabolomics and 16S metabarcoding data for future analyses of the contaminants fate and impact in Mediterranean lagoons. First, semi targeted analytical procedures for water and sediment matrices were set up to evaluate the lagoon contamination status. Forty-six compounds were detected, 28 could be quantified in both water (between 0.09 and 47.4 ng/L) and sediment (between 0.008 and 26.3 ng/g) samples using UHPLC-MS/MS instrument. Regarding the non-targeted metabolomics study (UHPLC-HRMS), four sample preparation protocols, based on solid/liquid extractions and an automated pressurized fluid extraction system (EDGE® extractions), were compared in terms of metabolome coverage, efficiency and reproducibility of the extraction methodology. A solid/liquid extraction using acetonitrile/methanol (50/50) solvent was the best protocol. On the other hand, in order to characterize the microbial diversity of the lagoon sediment using metabarcoding, five commercial kits for DNA extraction were evaluated. This study revealed that the DNeasy PowerSoil Pro Qiagen Kit (Promega, USA) was the best compromise for studies assessing microbial diversity in fresh sediment.

The compositions of metalliferous sediments which is associated with hydrothermal vents can provide reliable geochemical indicators for the exploration of seafloor sulfides. In this study, surface sediments from the Xunmei hydrothermal field (HF) on the South Mid-Atlantic Ridge (SMAR) were selected, and their major and trace elements were analysed. The results showed that the sediments are composed of pelagic material (calcium biogenic components), basaltic debris, iron-manganese oxides, and a mixture of hydrothermal components. Additionally, the sediments were found to be significantly enriched in Cu, Zn, Fe and Co derived from hydrothermal sources, as well as Mn, V, Mo, U and P, which are primarily scavenged from seawater. The Cu and Zn concentrations are highest in the northeastern part of Xunmei, while the northeastern, northern, and southern parts are characterized by great inputs of hydrothermal Fe. Manganese and Mo are mainly enriched in the western and southern parts and show a strong positive correlation, indicating that Mo is mainly scavenged by Mn oxides. There are high positive correlations among U, P, and Fe, indicating their coprecipitation with Fe from hydrothermal plumes. Vanadium and Co are introduced into sediments in two ways, i.e., V is scavenged and coprecipitates from hydrothermal plumes, and Co is derived from sulfide debris. Based on the variations in Cu and Zn contents and in the Cu/Fe (0.159), Zn/Fe (0.158), and Fe/Mn (1440) ratios, it can be inferred that a high-temperature hydrothermal vent existed in northeastern Xunmei. In combination with the distribution patterns of the above elements, the hydrothermal vents in the southern part ceased erupting after a short period of activity. In addition, the high Mn anomaly and the high U/Fe ratios at the boundaries of the investigated area indicate the presence of a relatively oxidized environment in southwestern Xunmei.

In this study, the field measurement-based validation of a novel sediment transport calculation method is presented. River sections with complex bed topography and inhomogeneous bed material composition highlight the need for an improved sediment transport calculation method. The complexity of the morphodynamic features can result in the simultaneous appearance of the gravel and finer sand dominated sediment transport (e.g. parallel bed armoring and siltation) at different regions within a shorter river reach. For the improvement purpose of sediment transport calculation in such complex river beds, a novel sediment transport method was elaborated. The base concept of it is the combined use of two already existing empirical sediment transport models. The method was already validated against laboratory measurements. The major goal of this study is the verification of the novel method with a real river case study. The combining of the two sediment transport models is based on the implementation of a recently presented classification method of the locally dominant sediment transport nature (gravel or sand transport dominates). The results are compared with measured bed change maps. The verification clearly refers to the meaningful improvement in the sediment transport calculation by the novel manner in case of spatially varying bed content.

The Bay of Espirito Santo is located in the Espírito Santo State, in the eastern part of Brazil. It is surrounded by the city of Vitoria on one side and by the Atlantic Ocean on the other. Superficial sediments of Espirito Santo Bay were analyzed at 12 (western shallow silt sediments) + 8 (eastern sandy sediments and relatively deep sampling stations) = 20 uniformly distributed sampling points where geochemical analysis was performed. Nineteen elements were analyzed: Mo, Cu, Pb, Zn, Ag, Ni, Mn, Fe, As, U, Th, Sr, Cd, Sb, Bi, V, Cr, Ba, and Al. This selection was made based on the most representative heavy metals present in this area and according to the results obtained from the geochemical analysis. Their concentrations were compared with metal contamination benchmarks like Screening Quick Reference Tables (SQuiRTs), Effects Range-Low (ERLs) and Effects Range-Median (ERMs), TELs (Threshold Effects Levels), PELs (Probable Effects Levels), ERM (Effects range median), and AETs (Apparent Effects Thresholds). Results indicate that there is no particular pollution condition able to alter the condition of any part of this water body. The Authors conclude that the Espirito Santo Bay is only moderately polluted and some elements are virtually absent.

The Bay of Espirito Santo is located in the Espírito Santo State, in the eastern part of Brazil. It is surrounded by the city of Vitoria on one side and by the Atlantic Ocean on the other. Superficial sediments of Espirito Santo Bay were analyzed at 12 (western shallow silt sediments) + 8 (eastern sandy sediments and relatively deep sampling stations) = 20 uniformly distributed sampling points where geochemical analysis was performed. Nineteen elements were analyzed: Mo, Cu, Pb, Zn, Ag, Ni, Mn, Fe, As, U, Th, Sr, Cd, Sb, Bi, V, Cr, Ba, and Al. This selection was made based on the most representative heavy metals present in this area and according to the results obtained from the geochemical analysis. Their concentrations were compared with metal contamination benchmarks like Screening Quick Reference Tables (SQuiRTs), Effects Range-Low (ERLs) and Effects Range-Median (ERMs), TELs (Threshold Effects Levels), PELs (Probable Effects Levels), ERM (Effects range median), and AETs (Apparent Effects Thresholds). Results indicate that there is no particular pollution condition able to alter the condition of any part of this water body. The Authors conclude that the Espirito Santo Bay is only moderately polluted and some elements are virtually absent.

The product is a centrifugal air extractor, whose objective is to extract the stale air of SARS-CoV-2 or Covid-19 (Coronavirus); designed for civil and commercial use, it works with a single-phase alternating current (AC) motor of 220 (V) and 50 (Hz), with high energy efficiency (EE). Developed under the Design Thinking methodology, by electromechanical simulation using NI Multisim 14.0 software, case design using Cfturbo 2020 R2.0 CAD software, and rapid 3D prototyping with the OverLord Pro printer; with a prototype of the conventional stator winding of a synchronous motor with a two-pole PMSM/IPM single-phase alternating current (AC) field winding and a 4000 (Gauss) ferromagnetic ceramic magnet rotor. Innovating online nº 15 of invention patent nº 381968 by Nikola Tesla, 5/1/1888.One of the objectives is to link the middle level or Technical Schools with the University system (and careers with a Technological profile) through Project B374 located in the Secretariat of Science and Technology (SCyT) of the National University of La Plata ( UNLP), whose title is: “Integrated Management of Design and Innovation. Contributions for a theoretical-conceptual and methodological review” by the Director: Mg. Federico del Giorgio Solfa. Just as links were sought with the Research and Development Laboratory of the Department of Industrial Design (LIDDI-FBA-UNLP) through its Director D.I. Pablo Ungaro and D.I. Ana Bocos. In 2021, the project participated in the INNOVAR National Contest of the Ministry of Science, Technology and Productive Innovation of the Nation (MINCYT), Argentine Republic; in the "Covid-19 Projects" category, having been selected in the catalog of innovative products, won the 1st. "Covid-19 Projects" position of the National Agency for Research and Technological Development and local innovation (R+D+i) dependent on MINCYT.The results showed, according to the analysis of the test bench, that the PMSM/IPM type synchronous motor used in the centrifugal fan, with the innovation of the reactance-inductive control in series plus the capacitor in parallel, reduces the power by 67% (Watts) and active energy consumption (kWh), performing 56% more mechanical work (Joules) on the fluid air (with a 50% reduction in carbon footprint). Which leads us to the following conclusion: it is possible to develop centrifugal fans that save electricity (kWh) without the need to resort to (1) the "Fan Affinity Law", nor (2) the use of variable speed drives (VDF) or frequency (which are devices with complex and expensive electronics). Which would bring an enormous saving of the cost of electrical energy.

Natural radioactivity of 238U, 232Th and 40K for liquid and solid samples collected from Sidi Salem dam (Tunisia) and Aïn Dalia dam (Algeria) were measured using TERRA detector of rays (gam-ma, beta, and alpha), Atomic adsorption and Gamma-ray spectrometry were used to analyze the levels of radionuclides and toxic heavy metals, respectively. Toxic heavy metals (Fe, Bb, Zn, Ni, Cu, Cr and Cd) and associated health risks in surface water and sediment of dams have been in-vestigated in this present study. The radioactivity mean rates in the water samples were 1.72±0.01, 0.068±0.01 and 94.6±1.04 Bql-1 for 238U, 232Th and 40K respectively (Tunisia dam) and were 1.9± 0.24, 0.09±0.01 and 131.43±1.03 Bql-1 for 238U, 232Th and 40K respectively (Algeria dam). The 238U, 232Th and 40K radioactivity mean concentration measured in the sediment samples were 2.67±0.01, 0.18±0.012 and 197.87±2.01 Bqkg-1 respectively (Tunisian dam) and were 4.34±0.05, 0.27±0.05 and 287.61±3.34 Bqkg-1 respectively (Algeria dam). The activity concentration of 40K was higher than that of 238U and 232Th for the water and sediment samples. The mean activity concen-trations follow the order 40K > 238U > 232Th. The cumulative impact can be a serious immediate radiological health burden on the ecosystem, environment and people's health in this study area and can be transposable to any other similar region. The good knowledge of monitoring quality and quantity for the transboundary water resources and the international collaborations are es-sential to safeguard human health (women’s breasts cancer, thyroid cancer, neurological im-pact…), and avoid the conflicts, especially during these climatic upheavals of drought.

Diesel contamination of farming soils is of great concern because hydrocarbons are toxic to all forms of life and can potentially enter the food web through crops or plants used for remediation. Data on plant ability to uptake, translocate and accumulate diesel-derived compounds are controversial not only due to the probable diverse attitude of plant species but also because of the lack of a reliable method to distinguish petrogenic from biogenic compounds in plant tissues. The purpose of this study was to set up a GC-MS-based protocol enabling the determination of diesel-derived hydrocarbons in plants grown in contaminated soil for assessing human and ecological risks, predicting phytoremediation effectiveness and biomass disposal. To this aim two plant species Vicia sativa L. and Secale cereale L., belonging to two diverse vascular plant families, were used as plant models. They were grown in soil spiked with increasing concentrations of diesel fuel and the produced biomass was used to set up the hydrocarbon extraction and GC-MSD analysis. The developed protocol was also applied to the analysis of Typha latifolia L. plants, belonging to a different botanical family and grown in a long-time and highly contaminated natural soil. Results showed the possibility of distinguishing diesel-derived compounds from biogenic hydrocarbons in most terrestrial vascular plants, just considering the total diesel compounds in the n-alkanes carbon range C10-C26, where the interference of biogenic compounds is negligible. Diesel hydrocarbons quantification in plant tissues was strongly correlated (0.92<r2<0.99) to the concentration of diesel in spiked soils, suggesting a general ability of the considered plant species to adsorb and translocate relative low amounts of diesel hydrocarbons and the reliability of the developed protocol.

Suspended and deposited sediments in streams can interfere with filter-feeding caddisfly larvae by reducing feeding sites and feeding efficiency, potentially lowering densities, growth rates, and secondary production of an important trout prey. We conducted field studies at multiple stream sites with differing suspended sediment loads, and a laboratory study conducted under controlled conditions, together designed to examine the role of suspended sediments in the population dynamics and behavior of Brachycentrus occidentalis (Trichoptera: Brachycentridae) larvae in a Minnesota, USA, trout stream. Stream sites that had elevated turbidities and suspended sediments also had significantly more fine bottom substrates and higher substrate embeddedness. In addition, Brachycentrus densities were reduced, growth rates were slower, secondary production was reduced, and overall benthic macroinvertebrate taxa richness was lowest at the site with the highest suspended sediment loading. Colder water temperatures at one site also influenced Brachycentrus production. In 24-hour laboratory studies conducted in recirculating aquaria, the feeding activities of Brachycentrus larvae were reduced and positioning altered under high turbidities (500 nephelometric turbidity units, NTU) relative to low turbidities (50 NTU or lower). High suspended sediment loads have adversely affected filter-feeding caddisfly larvae by embedding and burying preferred coarse feeding substrates, altering their feeding positions and movements during highest flows, and ultimately impacting densities, growth rates, and secondary production.

The Hwangdo tidal flat is an intertidal landform located in Cheonsu Bay, Taean-gun, Chungcheongnam-do, on the west coast of Korea. The topographical characteristics of the semi-enclosed bay on the eastern side of the study area include waterways, sandbars, small islands, and tidal flats. In this study, data were acquired from tide gauges installed on the Hwangdo Bridge, and the height of the ellipsoid was measured using a real-time kinematics global positioning system (RTK-GPS). Digital elevation model (DEM) using Matrice 300 drone data were also acquired after processing. The geochemical sediment characteristics in the study area were analyzed, together with tidal-flat exposure-time characteristics based on environmental factors. Sediment data (n = 107) collected from October 25 to 28, 2022 (Korean local time) were used to classify sediment particles according to Folk and Ward (1957). Sedimentary facies ranged from coarse sand (sand:mud ratio = 9:1) to sandy silt (sZ) followed by muddy sand (mS) and slightly gravelly sandy mud ((g)sM). Total organic carbon (TOC) in the surface sediments were also characterized based on a particle-size analysis. The mean change in tidal height measured at Hwangdo Bridge during the sampling period was ~7.53 m (minimum: –3.86 m, maximum: +3.67 m). Based on the Boryeong's sea level measurement tide data in 2022, the tidal area in the drone images ranged from 6.362 m² (0.006 km²) at DEM +4.0 to 4,841,078 m² (4.841 km²) at DEM –4.0 m, indicating an increase in the tidal-flat area according to the tidal level of up to ~800-fold. The daily average exposure time was 9.0 h (minimum: 1.5 h, maximum: 17.9 h). Based on the results of multivariate analysis using exposure times and a geochemical dataset, four groups were identified: upper, middle, and lower intertidal zones and regions with a relatively high organic-matter concentration. A determination of the main characteristics of the Hwangdo tidal flat according to their spatial distribution showed that, among various environmental factors, changes in the sand or clay sediment composition were determined by community factors. The results of this study demonstrate the four statistically processed groups of marine environmental characteristics in the Hwangdo tidal flats. Changes in sedimentary patterns, rather than in the exposure time, accounted for the differences in the sediment compositions of the upper, middle, and lower stations, a response that is expected to continue.

Copper smelting has been the source of soil contamination in trace metals in Penga Penga (Lubumbashi). Residents are exposed to trace metal ingestion and planting trees is challenging in such soil conditions. Nevertheless, planting trees in former household dumps or using various types of amendments allowed the provisioning of fruits in few residences. In the perspective of scaling up the process, a survey has been conducted with the aim of assessing the effectiveness of the planting processes on the trace metal content in fruits and leaves of Mangifera indica L. and Syzygium guineense (Willd) DC. Samples were collected in residential households from Penga Penga and Kalebuka (a non-polluted suburb). The bioconcentration factor (BCF) and the safe weekly consumption (SWC) were calculated for each species. Results showed higher values of total and soluble concentrations of Cu, Pb, and Zn in the rhizosphere of the two species at Penga Penga. Metal concentrations were higher in fruits and leaves from Penga Penga with 47% of samples above FAO and WHO thresholds (vs 18.5% in Kalebuka). The BCF values were below 1 demonstrating the effectiveness of the process to reduce metal translocation to leaves and fruits. Recommendations from the SWC limited by Pb for consumption to 9 kg for mango flesh and by Cd 6.6 kg for S. guineense fruits at Penga Penga (Vs 78 and 68 kg at Kalebuka). Finally, results from this study provide interesting lessons from the scaling up and the technical itinerary of planting tree un Penga Penga.

Proper management of water is a challenge for every individual but especially for companies. Nowadays also legislation obliges companies to clean the wastewater before being discharged into municipal public sewer especially if they use some chemicals or oily elements in their production process. Construction of the wastewater cleaner depends directly on the way of pollution, the amount of contaminated water and the energy demand of the cleaning process. The paper deals with the construction of the wastewater cleaner, which is based on the technology of electro-flotation for the treatment of water contaminated with disperse colorants. The experimental work as well as the modelling using the statistical methods proved the suitability of the chosen technology. Also, each colour combination requires a specific time period for the water treatment. The authors determined the time interval for cleaning the wastewater that was polluted with yellow colour to 33 minutes. Finally, the wastewater cleaner that is based on the electro-flotation technology was included in the company’s reverse logistics system.

River bed materials serve multiple environmental functions as a habitat for aquatic invertebrates and fishes. At the same time, the particle size of the bed material reflects the tractive force of the flow regime in a flood and provides useful information for flood control. The traditional river bed particle size surveys, such as sieving, require time and labor to investigate river bed materials. The authors proposed a method to classify aerial images taken by unmanned aerial vehicle (UAV) using convolutional neural networks (CNN), our previous study showed that terrestrial riverbed material could be classified with high accuracy. In this study, we attempted to classify riverbed materials distributed in shallow waters where the bottom can be seen from UAVs. After training the CNN to classify the images with the same grain size as being in the same class even if the surface flow types taken overlapping the riverbed material were different, the total accuracy reached 90.3%. Moreover, the proposed method was applied to the wide-ranging area to determine the distribution of the particle size. In parallel, the microtopography was surveyed using Lidar-UAV, and the relationship between the microtopography and particle size distribution was discussed. In the steep section, coarse particles were distributed and formed a rapid. Fine particles were deposited on the upstream side of those rapids, where the slope had become gentler due to the damming. There was good agreement between the microtopographical trends and the grain size distribution.

The Rb/Sr ratio of lake sediments has been widely adopted as an indicator of weathering intensity in studies of past climate change, but the geochemical significance of this ratio varies with timescale. Here we present Rb/Sr data for the last 300 years for sediments collected from Chaonaqiu Lake in the Liupan Mountains of the western Chinese Loess Plateau as a decadal-scale record of weathering intensity. To validate the application of this weathering proxy, we correlated the record with those of other major elements, rock-forming minerals, and paleoclimatic proxies. We found that Rb/Sr ratios are influenced mainly by Sr activity within the lake catchment (where Sr is likely sourced from albite). In addition, higher (lower) Rb/Sr ratios of bulk sediments from Chaonaqiu Lake are correlated with lower (higher) fractions of terrigenous detritus (SiO2, Ti, K2O, Al2O3, and Na2O). Lake bulk sediment Rb/Sr ratios are dominated by the input of terrigenous detritus over decadal timescales. Our data show that physical and chemical weathering in Chaonaqiu Lake catchment have opposing influences on bulk sediment Rb/Sr ratios, competing to dominate these ratios of lake sediments over different timescales, with ratios reflecting the relative importance of the two types of weathering. We infer that the Rb/Sr ratios of Chaonaqiu Lake sediments reflect climatic signals of precipitation and temperature over long timescales and of precipitation over short timescales.

In the Quaternary paleosciences, the rationale behind analogical inference presupposes that former natural changes can be explained by causes operating now, although their intensity and rates can vary through time. In this paper we synthesise synthetize the results of different modern analog studies and discuss their value to obtain the best inferences from high resolution past records. This synthesis is based on the following: 1) The monthly monitoring of calcite precipitation reveals a strong connection with primary producers and between-years variability; this precipitation produces a seasonal signal with imprint on varve formation. 2) Clear pollen sedimentation peaks occur in spring/summer and fall/winter that coincide with temperature, precipitation, relative humidity and winds; this pattern converges with the two-layer coupled varves representing the same seasonality. 3) We assess the lake’s contemporary oxygenation dynamics over a three- year period; a combination of sedimentary REDOX proxies revealed different scenarios of oxic/anoxic shifts since 1500 CE. 4) We investigate presence of seasonality in the production/distribution of glycerol dialkyl glycerol tetraethers and derived temperature estimates in soils and particulate matter. Branched glycerol dialkyl glycerol tetraethers signatures and some derived temperature estimates proxies appear to mainly depend on the non-seasonal shifts in soil properties. 5) Currently we examine relationships and similarities between extant phytoplankton and derived pigments in water and traps, and their correspondence with subfossil pigments; some preliminary results are presented here.Keywords: high resolution, endogenic varves, calcite precipitation, pollen sedimentation, meromixis, freshwater glycerol dialkyl tetraether, subfossil pigments, long-term ecology.

We analyzed mineralogical characteristics, and major as well as rare earth element concentrations from a cryptotephra layer in sediments of the infilled maar of Auel (Eifel, Germany). The results of detailed geochemical analyses of clinopyroxenes and their glassy rim of the specific layer are most similar to those from the Campanian Ignimbrite (CI) Tephra occurrence in a loess section at Urluia (Romania). Both records show idiomorphic green clinopyroxenes and formation of twisted minerals up to millimeter scale. The cryptotephra in the Auel core has an age of around 39,940 yr b2k in the ELSA-20 chronology, almost identical to the latest Ar/Ar dates for the Campanian Ignimbrite/Y5 eruption. These observations suggest that parts of the CI ash cloud were transported also northwestward into Central Europe, whereas the main branch of the CI ash plume was transported from southern Italy towards the NE, E and SE.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Based on the geochemical analysis of the volcanic material from the sediment core AMK-340, central zone of the Reykjanes Ridge, we could detect two ash-bearing sediment units accumulated during the Termination I. They correlate to the Ash Zone I in the North Atlantic Late Quaternary sediments having an age of 12170-12840, within the Younger Dryas cold chronozone, and 13600-14540 years, within and Bølling-Allerød warm chronozone. The ash of the Younger Dryas unit is presented mostly by the mafic and persilicic material originated from the Icelandic volcanoes; Vedde Ash is presented in one sediment sample from this unit. The ash of the Bølling-Allerød unit is presented mostly by the mafic shards which are related to the basalts of the rift zone on the Reykjanes Ridge, having presumably the local origin. A detection of Vedde Ash helped to specify the timing of the previously reconstructed paleoceanographic changes for the Termination I in the point of study: a significant warming in the area could occur as early as 300 years prior to the end of the conventional Younger Dryas cold chronozone.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.