The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

The article presents a multiphase numerical computational fluid dynamics (CFD) for simulating hydrothermal liquefaction of sewage sludge in a continuous plug-flow reactor. The discrete particle method (DPM) was used to analyze the solid particle interaction in liquid-solid high shear flows to investigated coupling computational fluid dynamics (CFD) and discrete phase model (DPM) method. Increasing solid particles interaction were observed with increasing liquid velocity. The study examined the influence of parameters such as flow rate, temperature and residence time on the efficiency of bio-oil production. Furthermore, the trajectories of the solid particles are affected significantly by the ash flow and the solid particle size, thus the trajectories of particles resembles the streamlines. A parametric study is performed to investigate the effect of slurry flow rate, temperature and external heat transfer coefficient on the biocrude oil productions performance. This simulation data will be used in the future to design and scale up a large-scale HTL reactor.

In this work, we proposed a novel design of microfluidic mixer utilizing the amplified Marangoni chaotic advection induced by AC continuous electrowetting of a metal droplet situated in electrolyte solution, due to the linear and quadratic voltage-dependence of flow velocity at small or large voltages, respectively. Unlike previous researchers exploiting the unidirectional surface stress with DC bias at droplet/medium interface for pumping of electrolyte where the resulting flow rate is linearly proportional to the field intensity, dominance of another kind of dipolar flow pattern caused by local Marangoni stress at the drop surface in sufficiently intense AC electric field is demonstrated by both theoretical analysis and experimental observation, which exhibits a quadratic growth trend as a function of the applied voltage. The dipolar shear stress merely appears at larger voltages and greatly enhances the mixing performance by inducing chaotic advection between the neighboring laminar flow. The mixer design developed herein, on the basis of amplified Marangoni chaotic advection around a liquid metal droplet at larger AC voltages, has great potential for chemical reaction and MEMS actuator applications, because of generating high-throughput and excellent mixing performance at the same time.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Bio-separation of natural molecules as well as clinical compounds has been constantly developed in last decades. Several techniques are available but the majority of them presents drawbacks such us impossibility to be applied for industrial purposes. The main limitations for the scaling up are high costs and the fact that the devices work with microfluid dynamics. Nevertheless, magnetic bio-separation is considered the most prone to be used for large scale applications. Herein, we propose a simple magnetic separation method that is not based on microfluid dynamics, can work in a continuous- and high-flow rate and can be easily automated in order to be used for standard separation purposes. It is based on the use of an anisotropic flexible ferric magnetic strip, Teflon hoses and a pumping device. We show the modelling of the separation process along with an experimental test on iron oxide magnetic particles. The results showed that it is possible to remove, and separately collect, more than 92% of magnetic particles from a liquid solution of 100 ml in roughly 15 minutes.

Nucleoside analogs are commonly used drugs for the treatment of cancer and viral infections. Nucleoside deoxyribosyltransferase (NDT) is one of the key enzymes required for the biosynthesis of deoxynucleotides. The feasibility of biochemical transformation processes is usually greatly dependent on the cost of biocatalysts. Therefore, immobilizing and reusing biocatalysts is an approach to be considered to bring biotransformations closer to industrial feasibility, since it not only allows enzymes to be reused but can also improve their stability under several reaction conditions. In this work, histidine tags have been successfully fused to a Nucleoside deoxyribosyltransferase from Lactobacillus reuteri (LrDNT), which has been produced in a bench-scale reactor using a facile araBAD promoter-based protein expression system in an industrial microorganism, the E. coli BL21(DE3) strain. The overexpressed LrNDT was bound to a nickel-chelating agarose affinity chromatography medium via a one-step purification and immobilization process with a 99% yield, retaining about 97% of its initial activity. The optimal conditions for the immobilized LrNDT maintain high enzyme activity within the range of 20-45°C and pH 6.0-7.5. Finally, the immobilized enzyme reactor (IMER) of LrNDT was applied for the continuous-flow biosynthesis of 2'-deoxyadenosine and retained 90% of its activity after 16 hours, providing a theoretical basis for the industrial production of nucleoside analogs.

The pharmaceutical industry is undergoing a shift in processing methods for small-scale production (250-1000 kg/a), leading to an increased focus on continuous production research. Various concepts were developed to overcome challenges in small-scale crystallization for the production of high-quality products. However, further optimization is needed to enhance the industrial applicability of these concepts. This study aims to demonstrate the practical applicability of the Slug Flow Crystallizer (SFC) in the pharmaceutical industry by extending its use to a wider range of substance systems for small-scale API production. Employing an experimental strategy, the research seeks to rapidly assess the SFC's potential for achieving uniform, high-purity product yields, emphasizing the importance of factors such as slug flow stability, residence time distribution, and substance-specific crystallization criteria. This, coupled with our previously published model-based strategy, forms a comprehensive methodology to explore crystallization behavior and modeling for a variety of substance systems within the SFC. The ultimate goal of this study is to showcase the practicality of the SFC in the pharmaceutical industry, enabling the way for its reliable use in long-term, small-scale continuous crystallization and the production of high-quality pharmaceutical products.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

In a Water-Cooled Lithium-Lead (WCLL) Breeding Blanket (BB), the heat generated by the plasma thermal radiation and nuclear reactions is removed mainly by two components; namely, the First Wall (FW) and the Breeding Zone (BZ). The FW faces the neutrons and charged particles fluxes generated by the fusion reactions and the thermal radiation coming from the plasma. The present work takes into account the FW cooling system inspired by the WCLL BB 2018 design of DEMO 2017 baseline. Unlike the baseline where a Pressurized-Water Reactor (PWR) setup is used for the coolant, various setup between the Boiling Water Reactor (BWR) and the High-Pressure (HP) BWR are studied in the present work operating in the Two-Phase Flow (TPF) regime. The 3D model of the FW in the WCLL BB 2018 design is simplified into a 1D model and a steady state analysis is carried out to optimize the mass flow rate of the water and the number of parallel channels at the BB cells at different poloidal locations of the reactor, which helps not only in reducing the used coolant but also in improving the Tritium Breeding Ratio (TBR). The present work takes into account forced convection in the liquid only region, the subcooled boiling region, and the saturated boiling region using suitable empirical or semi-empirical models from the literature. The results are validated against the existing results in the literature. In the end, related conclusions are made regarding the pros and cons of the studied operating conditions.

Public restrooms are often a hub of microbial contamination, and the examination of bacterial contamination in these facilities can serve as an important indicator of the transmission of infectious diseases. This study was conducted to determine the prevalence of bacterial contamination in public restrooms based on the economic class of the building. Samples were collected from various spots in 32 restrooms found in 10 shopping malls, classifying them into two categories: upper-end restrooms and lower-end restrooms. The findings showed that the level of contamination was higher in the lower-end restrooms, with the seat being the most contaminated area. The most dominant Gram-positive bacteria were coagulase-negative staphylococci species, making up 86% of the identified Gram-positive isolates. The most dominant Gram-negative bacteria identified were Klebsiella pneumoniae and Pseudomonas aeruginosa. The antibiotic sensitivity test results revealed the presence of multi-drug resistant bacteria among the Gram-positive and negative isolates, including Staphylococcus haemolyticus, Staphylococcus kloosi, Acinetobacter baumanii, and Pseudomonas aeruginosa. In conclusion, the study underscores the significance of monitoring bacterial contamination in public restrooms and the need for measures to reduce the spread of infectious diseases. Further research is crucial to gain a complete understanding of the bacterial contamination in public restrooms and their resistance patterns, to ensure the safety and health of the public. The implementation of improved cleaning practices and hands-free designs in restrooms can help reduce the risk of cross-contamination and prevent the spread of diseases.

The separation of microparticles with respect to different properties such as size and material is a research field of great interest. Dielectrophoresis, a phenomenon which is capable of addressing multiple particle properties at once, can be used to perform a chromatographic separation. However, the selectivity of current dielectrophoretic particle chromatography (DPC) techniques is limited. Here we show a new approach for DPC based on differences in the dielectrophoretic mobilities and the crossover frequencies of polystyrene particles. Both differences are addressed by modulating the frequency of the electric field to generate positive and negative dielectrophoretic movement to achieve multiple trap and release cycles of the particles. A chromatographic separation of different particle sizes revealed a voltage dependency of this method. Additionally, we showed the frequency bandwidth influence on separation using one example. The DPC method developed was tested with model particles but offers possibilities to separate a broad range of plastic and metal microparticles or cells and to overcome currently existing limitations in selectivity.

In this article, the biocatalytic oxidation of ethanol into acetaldehyde was studied using a catalase entrapped within monolithic polyampholyte cryogel, p(APTAC-co-AMPS), derived from an anionic monomer, 2-acrylamido-2-methyl-1-propanesulfonic acid sodium salt (AMPS), and a cationic monomer, (3-acrylamidopropyl) trimethylammonium chloride (APTAC) as catalyst. Macroporous polyampholyte cryogels containing various amounts of catalase were synthesized in situ under cryo-polymerization conditions at a molar ratio of monomers [APTAC]:[AMPS] = 75:25 mol.% in the presence of 10 mol.% cross-linking agent, N,N-methylenebisacrylamide (MBAA). The conversion of ethanol into acetaldehyde in good-to-high yields was observed in flow-through and batch type reactors under optimal conditions: at T = 10-20 C, pH = 7.1, [C2H5OH]:[H2O2] = 50:50 vol.%. According to SEM image the pore sizes of p(AMPS-co-APTAC) cryogel vary from 15 to 55 μm. The catalytic activity of catalase entrapped within monolithic polyampholyte cryogel in the conversion of ethanol into acetaldehyde was evaluated through the determination of such kinetic parameters as Michaelis constant (Km), the maximum enzymatic rate (Vmax), activation energy (Ea), turnover number (TON) and turnover frequency (TOF). The catalase encapsulated within monolithic polyampholyte cryogel exhibits a high conversion of ethanol into acetaldehyde. The advantages and disadvantages of flow-through and batch type reactors were highlighted.

In order to perceive the behavior presented by the multiphase chemical reactors, the ant colony optimization algorithm was combined with computational fluid dynamics (CFD) data. This intelligent algorithm creates a probabilistic technique for computing flow and it can predict various levels of three-dimensional bubble column reactor (BCR). This artificial ant algorithm is mimicking real ant behavior. This method can anticipate the flow characteristics in the reactor using almost 30 % of the whole data in the domain. Following discovering the suitable parameters, the method is used for predicting the points not being simulated with CFD, which represent mesh refinement of Ant colony method. In addition, it is possible to anticipate the bubble-column reactors in the absence of numerical results or training of exact values of evaluated data. The major benefits include reduced computational costs and time savings. The results show a great agreement between ant colony prediction and CFD outputs in different sections of the BCR. The combination of ant colony system and neural network framework can provide the smart structure to estimate biological and nature physics base phenomena. The ant colony optimization algorithm (ACO) framework based on ant behavior can solve all local mathematical answers throughout 3D bubble column reactor. The integration of all local answers can provide the overall solution in the reactor for different characteristics. This new overview of modelling can illustrate new sight into biological behavior in nature.

In chronic myeloid leukemia (CML), a clonal proliferative disorder of granulocytic lineage, the 90%‐95% of cases are characterized by t(9;22) (q34.1;q11.2) translocation, leading to the Philadelphia chromosome (1). Rarely, CML patients directly present a blast crisis, mostly of myeloid origin (2, 3). Herein, we describe one rare CML case, showing an unusual early T lymphoid blastic crisis.

The theory of water transport in trees, according to which the main driving force of water movement is the suction created by the evaporation of water by the meniscus (the curved surface of the capillary liquid column) on the evaporating elements, supported from below by root pressure, is flawed. The capillary effect in nature is around one meter. In the case of open-air gaps, the leaf cannot suck in the water against gravity because, in this case, the plant would not be sucking in water, but air through the open-air gap. If not, how do trees transport water? When evaporation occurs, there is no suction towards the canopy, but pressure is due to a reduction in the cross-section of the water pipe caused by heat loss through evaporation. At night, when evaporation stops, a thermal equilibration process is triggered, which restores the original cross-section of the pipe. This generates suction and draws water from the soil. As the hydrostatic pressure in the pipe is high for tall trees, the pipe is cut off. To prove my theory, I have given several examples. Water transport is not based on physical mechanical laws alone. There may be complex physiological, biochemical, and biophysical processes behind the operation of the pipe system.

Let $(\Omega, \mu)$, $(\Delta, \nu)$ be measure spaces and $\{\tau_\alpha\}_{\alpha\in \Omega}$, $\{\omega_\beta\}_{\beta \in \Delta}$ be 1-bounded continuous Parseval frames for a Hilbert space $\mathcal{H}$. Then we show that \begin{align}\label{UE} \log (\mu(\Omega)\nu(\Delta))\geq S_\tau(h)+S_\omega (h)\geq -2 \log \left(\frac{1+\displaystyle \sup_{\alpha \in \Omega, \beta \in \Delta}|\langle\tau_\alpha , \omega_\beta\rangle|}{2}\right) , \quad \forall h \in \mathcal{H}_\tau \cap \mathcal{H}_\omega, \end{align} where \begin{align*} &\mathcal{H}_\tau := \{h_1 \in \mathcal{H}: \langle h_1 , \tau_\alpha \rangle \neq 0, \alpha \in \Omega\}, \quad \mathcal{H}_\omega := \{h_2 \in \mathcal{H}: \langle h_2, \omega_\beta \rangle \neq 0, \beta \in \Delta\},\\ &S_\tau(h):= -\displaystyle\int\limits_{\Omega}\left|\left \langle \frac{h}{\|h\|}, \tau_\alpha\right\rangle \right|^2\log \left|\left \langle \frac{h}{\|h\|}, \tau_\alpha\right\rangle \right|^2\,d\mu(\alpha), \quad \forall h \in \mathcal{H}_\tau, \\ & S_\omega (h):= -\displaystyle\int\limits_{\Delta}\left|\left \langle \frac{h}{\|h\|}, \omega_\beta\right\rangle \right|^2\log \left|\left \langle \frac{h}{\|h\|}, \omega_\beta\right\rangle \right|^2\,d\nu(\beta), \quad \forall h \in \mathcal{H}_\omega. \end{align*} We call Inequality (\ref{UE}) as \textbf{Continuous Deutsch Uncertainty Principle}. Inequality (\ref{UE}) improves the uncertainty principle obtained by Deutsch \textit{[Phys. Rev. Lett., 1983]}. We formulate Kraus conjecture for 1-bounded continuous Parseval frames. We also derive continuous Deutsch uncertainty principles for Banach spaces.

Estimating peak flow for a catchment is commonly undertaken using the design event method, however this method does not allow for the understanding of uncertainty in the result. This research first presents a simplified method of fragments approach to rainfall disaggregation that ignores the need to consider seasonality, offering a greater diversity in storm patterns within the resulting sub-daily rainfall. By simulating 20 iterations of the disaggregated sub-daily rainfall within a calibrated continuous simulation hydrologic model, we were able to produce multiple long series of stream flow at the outlet of the catchment. With this data, we investigated the use of both the annual maximum and peaks over threshold approaches to flood frequency analysis and found that for a one in 100 year annual exceedance probability peak flow, the peaks over threshold method (333m3/s ±50m3/s) was significantly less uncertain than the annual maximum method (427m3/s ±100m3/s). For the one in 100 year annual exceedance probability, the median peak flow from the peaks over threshold method (333m3/s) produced an outcome comparable to the design event method peak flow (328m3/s), indicating that this research offers an alternative approach to estimating peak flow, with the additional benefit of understanding the uncertainty in the estimation. Finally, the paper highlighted the impact that length and period of streamflow has on peak flow estimation and noted that previous assumptions around the minimum length of gauged streamflow required for flood frequency analysis may not be appropriate in particular catchments.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The fine chemical and pharmaceutical sectors are starting to advocate the use of flow chemistry due to reasons such as EHS, environmental, efficiency, cost saving and regulatory compliance. The use of trickle bed or fixed bed system could replace a batch autoclave typically used for hydrogenation reactions. However, there are few studies which detail the process from laboratory proof of concept through design to commercial realization. This study, using the production of 1,3-cyclohexanedione from catalytic hydrogenation of resorcinol as a case study demonstrates how the laboratory-scale recycle trickle bed can be used for catalyst screening and selection. Further, design data are generated by operation over a range of design superficial velocities and operating pressure that are used to derive a design correlation that is then used to specify a single stream plant at a level of definition consistent with a Preliminary Design for capital cost estimation. Finally, the further actions required in terms of data generation to increase the level of definition and confidence to a Sanction Grade or Final Design are discussed.

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. Under the working conditions in this study, a maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±10.0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately.

The purpose of our study was to discuss Rab 7 effects in chronic kidney disease (CKD). Methods: Using WT and Rab 7-/- mice as target animal, and HK-2 and HMEC-1 cell co-cultured to make cell model. Measuring kidney tissues were evaluated by Sirius red staining, immunohistochemistry staining to CD 34 protein, Transmission electron microscope (TEM) and gelatin zymography to MMP-2 activities. The cell proliferation were measured by CCK-8 and Ki67 protein expression. Measuring cell invasion and total length were evaluated by transwell and in vitro angiogenesis assay. MMP-2 activities were evaluated by gelatin zymography in cell groups. The relative proteins expression were evaluated by Western blot in kidney tissues and cell groups. Results: Hypoxia promoted the expression of Rab7 in HMEC-1, and the activity of MMP-2 related with regulatory molecules such as reversion-inducing-cysteine-rich protein with kazal motifs (RECK), negative correlation with membrane-type 1 MMP (MT1-MMP or MMP-14) on the membrane of TECs. In addition, the up-regulation of the expression of Rab7 inhibited the activity of MMP-2 and proliferation and cyclization of endothelial cells, and the inhibitor of MMP-2 partially blocked the effects of Rab7 on angiogenesis. Furthermore, the similar data were also obtained in the fibrosis kidney tissues of mice. Conclusion: Rab 7 might be an important role in hypoxic TECs regulated angiogenesis, Rab 7 knockdown could improve hypoxic TECs regulated angiogenesis, the relative mechanisms might be correlation with RECK pathway and MMP-2 activities in vivo and vitro study.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

The current state of biological knowledge contains an unresolved paradox: life as a continuity in the face of the phenomena of ageing. In this manuscript I propose a theoretical framework that offers a solution for this apparent contradiction. The framework proposed is based on a rethinking of what ageing is at a molecular level, as well as on a rethinking of the mechanisms in charge of the flow of information from one generation to the following ones. I propose an information-based conception of ageing instead of the widely accepted damage-based conception of ageing and propose a full recovery of the chromosome theory of inheritance to describe the intergenerational flow of information. Altogether the proposed framework allows a precise and unique definition of what life is: a continuous flow of biological information. The proposed framework also implies that ageing is merely a consequence of the way in which epigenetically-coded phenotypic characteristics are passed from one generation to the next ones.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

The calculation and visualization of the dose field in the decommissioning of nuclear facilities is one of the important functions of the decommissioning virtual simulation system, which can provide accurate and intuitive radiation field distribution and play an important role in determining the demolition plan and protecting personnel during the engineering implementation process. This article investigates the development of dose field calculation and visualization in the reactor decommissioning virtual simulation systems, and preliminarily proposes a technical plan suitable for the development of the decommissioning dose field calculation and visualization display programs for the first Heavy Water Research Reactor (HWRR) in China. Besides, the applicability of the selected scheme is analyzed, the functional requirement and development direction of the HWRR reactor decommissioning dose field calculation and visual display module are preliminarily determined. Furthermore, the reactor vessel of HWRR reactor is modeled and the dose field distribution was calculated and visualized. This research can provide technical support for the development of the decommissioning simulation system for the first HWRR reactor in China.

Hydrogen gas (H2) has attracted attention as a next-generation clean energy source. Its efficient and safe preparation and utilization are crucial in both industry and organic chemistry. In this study, a Pt/CB-catalyzed MW-mediated continuous-flow hydrogenation reaction was developed using methylcyclohexane (MCH) as the reducing agent (hydrogen carrier). Alkynes, alkenes, nitro groups, benzyl esters, and aromatic chlorides were chemoselectively hydrogenated using Pt/CB under MW-assisted continuous-flow conditions. This methodology represents a safe and energy-efficient hydrogenation process, as it eliminates the need for an external hydrogen gas supply or heating jackets as a heat medium. Further application of MW-mediated continuous-flow hydrogenation reactions is a viable method for the efficient generation and utilization of sustainable energy.

Many large-scale studies revealed that exogenous erythropoietin, erythropoie-sis-stimulating agents, have no renoprotective effects. We investigated the effects of en-dogenous erythropoietin on renal function in ischemic reperfusion injury (IRI) of kidney using prolyl hydroxylase domaine (PHD) inhibitor, Roxadustat (ROX). 4 hr hypoxia (7% O2) and 4 hr treatment by ROX prior to IRI did not improve renal function. In contrast, 24-72 hr pre-treatment by ROX largely improved the decline of renal function by IRI. Hy-poxia and 4 hr ROX increased interstitial cells-derived Epo production by 75 and 6-fold, respectively, before IRI and worked as exogenous Epo. 24-72 hr ROX treatment increased Epo production during IRI by 9-fold. Immunohistochemistry revealed that 24 hr ROX caused Epo production in proximal and distal tubules and worked as endogenous Epo. Our data show that 24-72 hr ROX-induced tubular endogenous Epo production results in renoprotection but peritubular exogenous Epo production by interstitial cells-derived in-duced by hypoxia and 4 hr ROX did not. Stimulation of tubular but not peritubular Epo production may link to renoprotection.

Cerebrovascular and airway structures are tubular structures used for transporting blood and gases, respectively, providing essential support for the normal activities of the human body. Accurately segmenting these tubular structures is the basis of morphology research and patho-logical detection. Nevertheless, accurately segmenting these structures from images presents great challenges due to their complex morphological and topological characteristics. To address this challenge, this paper proposes a framework UARAI based on the U-Net multi-scale reverse at-tention network and sparse convolution network. The framework utilizes a multi-scale structure to effectively extract the global and deep detail features of vessels and airways. Further, it enhances the extraction ability of fine-edge features by a joint reverse attention module. In addition, the sparse convolution structure is introduced to improve the features' expression ability without increasing the model's complexity. Finally, the proposed training sample cropping strategy re-duces the influence of block boundaries on the accuracy of tubular structure segmentation. The experimental findings demonstrate that the UARAI-based metrics, namely Dice and IoU, achieve impressive scores of 90.31% and 82.33% for cerebrovascular segmentation and 93.34% and 87.51% for airway segmentation, respectively. Compared to commonly employed segmentation tech-niques, the proposed method exhibits remarkable accuracy and robustness in delineating tubular structures such as cerebrovascular and airway. These results hold significant promise in facilitating medical image analysis and clinical diagnosis, offering invaluable support to healthcare profes-sionals.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

Abstract: Severe land degradation is the principal environmental problem in Ethiopian highlands in the form of soil erosion, and soil fertility loss, which is caused by human intervention for food, shelter, and energy demands. Soil erosion contributes to the loss of precious soil and water resources which are the basis of agricultural production and provide numerous other eco-system services. The Ethiopian highlands are one of the most degraded regions in the world. To combat such problems, the government of Ethiopia has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. Mount Yewel is one of the highlands in Northeastern Ethiopia where intensive soil and water conserva-tion has been implemented. Despite the massive investment in soil and water conservation measures, most of the rivers in the highlands of Ethiopia carry huge amounts of sediment with high flood risks in the wet season and streams are dried up in the dry period. Nonetheless, the impact of soil and water conservation measures on flood reduction and dry season flow en-hancement has not yet been quantified and evaluated. This research was then conducted on paired micro-catchments of Mount Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were col-lected from 22/11/2020 to 8/11/2022 on paired micro-catchments of Mount Yewel at their outlets and centers respectively. Base flow separation was done from the stream hydrograph using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software were employed for data analysis. Flow duration curves (FDC) for both watersheds were developed to compare the stream flow patterns between treated and untreated micro-catchments of Mount Yewel. The FDC indi-cated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and unsustained in untreated micro-catchment. From statistical analysis, there is a significant (P

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

The main aims of this study were (1) to identify and compare the major biologically active compounds in the metabolome of ligulate and tubular flowers of two C. officinalis cultivars, ‘Golden Sea’ (GS) and ‘Paradise Garden’ (PG), and (2) to investigate the effect of different proportions of ligulate and tubular flowers in the inflorescences on their metabolome. Ultra-performance liquid chromatography with photodiode array detection and a Q Exactive Orbitrap high-resolution mass spectrometer were used to analyse the flower metabolome. Analysis of the metabolomics data revealed that polar lipids showed the most significant differences between flowers. Tubular flowers of PG and GS cultivars contained higher levels of 31 and 34 out of 36 lipids, respectively. Furthermore, tubular flowers of both cultivars contained significantly higher levels of phenolamides and caffeoylquinic acids, but lower levels of triterpenoids. To compare the metabolite content of the two C. officinalis cultivars, we analysed the data for their inflorescences. The study showed that GS inflorescences contained significantly higher levels of phenolic compounds and lipids than PG inflorescences. This GS advantage was due to two factors: firstly, the higher content of these metabolites in tubular flowers and, secondly, the higher proportion of tubular flowers in GS inflorescences.

IgA nephropathy (IgAN) is one of the most common forms of glomerular disease. It is diagnosed by the dominant or co-dominant IgA deposition in the mesangial region by histopathological examination of kidney biopsy. Kidney biopsy has its own complication and not performed frequently. microRNA (miRNA) is a small RNA, which plays an important role at the post transcriptional level by downregulating mRNAs. We have tried to establish a miRNA based biomarker for IgAN. We quantified miR-148b and let-7b from plasma in IgAN patients and healthy controls. Logistic regression models and receiver operating curve analysis used to analyze the miRNAs quantity and Oxford MEST-C scoring parameters (M- Mesangial hypercellularity, E- Endocapillary hypercellularity, S- Segmental glomerulosclerosis, T- Tubular atrophy/Interstitial fibrosis, C- Crescents). miR-148b and let-7b levels in IgAN were found to be higher by 2.9 and 5.48 times than the healthy controls, respectively. let-7b was positively correlated with complement C3 levels. Similarly, miR-148b was positively correlated with estimated glomerular filtration rate (eGFR) and negatively correlated with S, T, and blood pressure (BP). The sensitivity, specificity, and area under the curve (AUC) of receiver operating characteristic (ROC) for miR-148b against T were 0.87, 0.77, and 0.85, respectively. The threshold value of miR-148b concentration was found to be 8479 to differentiate the severe condition of IgAN. Furthermore, the decrease in miR-148b concentration at a threshold point indicated the progression of the severity of the IgAN. It can also be used to predict the IgAN at an earlier stage.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

In this paper, modification of dual-Halbach permanent magnet (PM) array is investigated to improve performance of tubular linear machine, in terms of flux density and output power. Instead of a classical Halbach array with only radial and axial PMs, proposed model involves insertion of mig-magnets, which have magnetized angle shifted from the reference magnetized angles of axial and radial PMs. This structure leads to elimination of flux leakage and concentration of flux linkage in middle of the coil; therefore, the performance of machine is increased.

The purpose of this work is to optimize angular extrusion for sever plastic deformation of tubular specimens. A finite element model (FEM) was built in Deform-3D^® for three extrusion dies and analyzed. The dies were ECAP (135°), TCAP with external groove of 90° (denoted as TCAP-e) and TCAP with internal groove of 90° (denoted as TCAP-i). The analysis for process parameters (such as coefficient of friction-μ, die angles-ѱ and φ, temperature - T, and radius ratio-R) showed that TCAP-i was the optimal die in processing Al6063 tubes based on strain and load distribution of the model. The TCAP-i die model was further optimized for different parameters namely die angles, coefficient of friction, deformation ratio and temperature. The results showed that at constant process temperature of 25 °C, the optimal TCAP-i has the following parameters: φ₂=80⁰, Ѱ₁=30⁰, Ѱ₂=80⁰, Ѱ₃=30⁰, μ =0.4 and R =1.5.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

We construct a Bayesian estimator for the dilution of a wastewater sample. When wastewater is diluted by rainwater an estimate of the level of dilution is required if we are to normalise sample measurements of disease markers such as SARS-CoV-2 RNA. We consider the situation where flow measurements are available, but will regularly be unreliable because of the action of combined sewer outflows (CSOs) and wastewater storage tanks, which divert wastewater away from treatment plants when the flow is excessive. However, we also have proxies for the flow from various chemical markers (e.g.\ phosphate, ammonium, electrical conductivity), whose level per unit of population is fixed. The new flow estimator has multiple advantages compared to existing procedures: credible intervals for the estimates; optimal weighting of the chemical markers; systematic handling of missing and censored values; and model based smoothing without lags.

We investigate properties of strongly useful topologies, i.e. topologies with respect to which every weakly continuous preorder admits a continuous order-preserving function. In particular, we prove that a topology is strongly useful provided that the topology generated by every family of separable systems is countable. Focusing on normal Hausdorff topologies, whose consideration is fully justified and not restrictive at all, we show that strongly useful topologies are hereditarily separable on closed sets, and we identify a simple condition under which the Lindelöf property holds.

Iterated games, in which the same economic interaction is repeatedly played between the same agents, are an important framework for understanding the effectiveness of strategic choices over time. To date very little work has applied information theory to the information sets used by agents in order to decide what action to take next in such strategic situations. This article looks at the mutual information between previous game states and an agent's next action by introducing two new classes of games: ’invertible games’ and ‘cyclical games'. By explicitly expanding out the mutual information between past states and the next action we show under what circumstances these expressions can be simplified. These information measures are then applied to the Traveler's Dilemma game and the Prisoner's Dilemma game, the Prisoner's Dilemma being invertible, to illustrate their use. In the Prisoner's Dilemma a novel connection is made between the computational principles of logic gates and both the structure of games and the agents' decision strategies. This approach is applied to the cyclical game Matching Pennies to analyse the foundations of a behavioural ambiguity between two well studied strategies: ‘Tit-for-Tat' and ’Win-Stay, Lose-Switch'.

Salmorejo is a homogenate based on tomato, olive oil and breadcrumbs commercialized as a “fresh-like” cold puree in Spain and other European countries. Salmorejo is thermolabile and requires pasteurising upon High Temperature, Short Time (HTST) conditions to inhibit microbes and enzymes. Due to its penetration, dielectric heating by radiofrequency (RF) might improve pasteurisation results of conventional heating (CH) in viscous products. The objective was to validate the pasteurisation temperature (70-100 °C, at 5 ºC intervals) for salmorejo processed by radiofrequency (operating at 27.12 MHz for 9.08 s) or conventional continuous heating. Salmorejo was prone to thermal damage upon HTST conditions. Main heat-induced changes include: orangeness, flavour homogenisation, loss of freshness, thickening, loss of vitamin C and lipid oxidation. A ‘fresh-like’ good quality salmorejo can be obtained using either conventional or radiofrequency pasteurisers. Both CH and RF equivalent treatments allowed a strong reduction of total and sporulated mesophilic microorganisms, and an adequate inhibition of the pectinmethylesterase, peroxidase and, to a lesser extent, polyphenoloxidase, but did not inhibit the polygalacturonase enzyme. Pasteurisation at 80 °C for 9.8 s (RF) or 10.9 s (CH) provided a good equilibrium in levels of microbiological and enzymatic inhibition and thermal damage to the product. Increasing this temperature does not improve enzyme inactivation levels and salmorejo may become overheated.

The early embryonic heart is a multi-layered tube consisting of (1) an outer myocardial tube; (2) an inner endocardial tube; and (3) an extracellular matrix layer interposed between myocardium and endocardium, called “cardiac jelly” (CJ). During the past decades, research on CJ has mainly focused on its molecular and cell biological aspects. This review focuses on the morphological and biomechanical aspects of CJ. Special attention is given to (1) the spatial distribution and fiber architecture of CJ; (2) the morphological dynamics of CJ during the cardiac cycle; and (3) the removal/remodeling of CJ during advanced heart looping stages, which leads to the formation of ventricular trabeculations and endocardial cushions. CJ acts as a hydraulic skeleton displaying striking structural and functional similarities with the mesoglea of jellyfish. CJ not only represents a filler substance, facilitating end-systolic occlusion of the embryonic heart lumen. Its elastic components antagonize the systolic deformations of the heart wall and thereby power the refilling phase of the ventricular tube. Non-uniform spatial distribution of CJ generates non-circular cross sections of the opened endocardial tube (initially elliptic, later deltoid), which seem to be advantageous for valveless pumping. Endocardial cushions arise from non-removed remnants of the original CJ.

Background: Dual function tail tubular proteins (TTP) belonging to the lytic bacteriophages are the interesting group of biologically active enzymes. Surprisingly, apart from their structural function, they are also polysaccharide hydrolyzes destroying bacterial extracellular components. One of the representatives of this group is TTPB from Klebsiella pneumoniae phage – KP32. TTPB hydrolyzes exopolysaccharide (EPS) of Klebsiella pneumoniae and Enterococcus faecalis strain. This depolymerizing feature was associated with the activity to prevent bacterial biofilm formation. TTPB can inhibit biofilm formation by K. pneumoniae, Enterobacter cloacae, Staphylococcus aureus, Enterococcus faecalis and Pseudomonas aeruginosa strains. Moreover, synergistic activity with antibiotic action has been observed, most likely due to depolymerases’ facilitation of contact of antibiotic with bacterial cells. Methods: TTPB was overexpressed in E coli system, purified and tested towards the bacterial strains using agar overlay method. The hydrolytic activity of TTPB was performed using EPSs of K. pneumoniae PCM2713 and E. cloacae ATCC 13047 as the substrates. Next, we determined the reducing sugar (RS) levels in the TTPB/EPS mixtures, regarding the RS amount obtained after acidic hydrolysis. The antibiofilm activity of TTPB has been set down on bacterial biofilm using a biochemical method. Finally, we have demonstrated the synergistic activity of TTPB with kanamycin. Results: For the first time, the hydrolytic activity of TTPB towards bacterial EPSs has been shown. TTPB releases about a half of the whole RS amount of EPSs belonging to K. pneumoniae PCM 2713 and E. cloacae ATCC 13047 strains. 1.12 µM of the phage protein reduces biofilm of both strains by over 60%. Destroying the bacterial biofilm the phage protein improves the antibiotic action increasing kanamycin effectiveness up to four times.

Let $(\Omega, \mu)$, $(\Delta, \nu)$ be measure spaces. Let $(\{f_\alpha\}_{\alpha\in \Omega}, \{\tau_\alpha\}_{\alpha\in \Omega})$ and $(\{g_\beta\}_{\beta\in \Delta}, \{\omega_\beta\}_{\beta\in \Delta})$ be continuous p-Schauder frames for a Banach space $\mathcal{X}$. Then for every $x \in \mathcal{X}\setminus\{0\}$, we show that \begin{align}\label{CUE} \mu(\operatorname{supp}(\theta_f x))^\frac{1}{p} \nu(\operatorname{supp}(\theta_g x))^\frac{1}{q} \geq \frac{1}{\displaystyle\sup_{\alpha \in \Omega, \beta \in \Delta}|f_\alpha(\omega_\beta)|}, \quad \nu(\operatorname{supp}(\theta_g x))^\frac{1}{p} \mu(\operatorname{supp}(\theta_f x))^\frac{1}{q}\geq \frac{1}{\displaystyle\sup_{\alpha \in \Omega , \beta \in \Delta}|g_\beta(\tau_\alpha)|}. \end{align} where \begin{align*} &\theta_f: \mathcal{X} \ni x \mapsto \theta_fx \in \mathcal{L}^p(\Omega, \mu); \quad \theta_fx: \Omega \ni \alpha \mapsto (\theta_fx) (\alpha):= f_\alpha (x) \in \mathbb{K},\\ &\theta_g: \mathcal{X} \ni x \mapsto \theta_gx \in \mathcal{L}^p(\Delta, \nu); \quad \theta_gx: \Delta \ni \beta \mapsto (\theta_gx) (\beta):= g_\beta (x) \in \mathbb{K} \end{align*} and $q$ is the conjugate index of $p$. We call Inequality (\ref{CUE}) as \textbf{Functional Continuous Uncertainty Principle}. It improves the Functional Donoho-Stark-Elad-Bruckstein-Ricaud-Torr\'{e}sani Uncertainty Principle obtained by M. Krishna in \textit{[arXiv:2304.03324v1, 2023]}. It also answers a question asked by Prof. Philip B. Stark to the author.

This paper investigates the importance of enhancing the safety of research reactors, especially in newcomer countries where experience may be limited. The focus is on the role of Independent Assessment (IA) and assessors in addition to using Best Estimate plus Uncertainty (BEPU) approach in enhancing safety measures. By using the best estimate codes to perform uncertainty calculations, the BEPU technique logically connects nuclear thermal hydraulics and nuclear reactor safety. BEPU is based on an understanding of the phenomena related to the reactor state. Reactor circumstances, such as those related to operations or accidents, could be identified in this way. The IA process, involves experts supporting design, installation, safety analysis, decommissioning, and modification. In order to shape the use of IA process in this study feedback from nuclear professionals was collected through questionnaires, revealing a consensus on the necessity of qualified regulatory bodies in newcomer countries. Additionally, the questionnaires highlighted the potential benefits of IA, such as minimizing accident risks and providing valuable insights for future analyses. The results indicate a global anticipation of increased research reactor construction, particularly in newcomer countries. The study discusses the propagation of input uncertainties, emphasizing the importance of considering various factors and parameters in safety assessments. The BEPU method was applied by using the COBRA-TF code by modeling onset of nucleate boiling (ONB) conditions for VVR-K research reactor. For uncertain parameters; ±1% inlet/initial pressure, ±1% inlet temperature, and ±1% linear heat rate, the ONB temperature in the axial region with the average cladding temperature was calculated to be 114.44℃. Table 2 (our references) provided a value of 114.6℃. The close agreement between the reference value and the COBRA-TF result shows that the model used in the calculation of the reference value and the Chen relation used by COBRA-TF are compatible.

Currently, most plastic waste stems from packaging materials, with a large proportion of this waste either discarded or used to derive fuel. Accordingly, there is growing interest in the use of pyrolysis in the context of chemically recycling non-recyclable (i.e., via mechanical means) plastic waste into petrochemical feedstock. The aim of this study is to use kinetic analyses to elucidate the pyrolytic properties of solid recovered fuel (SRF) produced using two types of reactors, namely, fixed bed and fluidized bed reactors. From the kinetic analysis, the activation energy corresponding to the rate of pyrolysis reaction conversion was obtained. In conclusion, we found that the pyrolysis occurs more vigorously in fluidized bed reactors compared to fixed bed reactors.

Industrial pilot projects often rely on proprietary and expensive electronic hardware to control and monitor experiments. This raises costs and retards innovation. Open-source hardware tools exist for implementing these processes individually, however, they are not easily integrated with other designs. The Broadly Reconfigurable and Expandable Automation Device (BREAD) framework provides many open-source devices which can be connected to create more complex data acquisition and control systems. This article explores the feasibility of using BREAD plug-and-play open hardware to quickly design and test monitoring and control electronics for an industrial materials processing prototype pyrolysis reactor. Generally, pilot-scale pyrolysis plants are expensive custom designed systems. The plug-and-play prototype approach is first tested by connecting it to the pyrolysis reactor and ensuring it can measure temperature and actuate heaters and a stirring motor. Next, a single circuit board system was created and tested using the designs from the BREAD prototype to reduce the number of microcontrollers required. Both open-source control systems were capable of reliably running the pyrolysis reactor continuously and the overall cost of control was reduced by more than 10X. Open-source, plug-and-play hardware provides a reliable avenue for researchers to quickly develop data acquisition and control electronics for industrial-scale experiments.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

This paper presents the results of investigations on the pyrolysis of tyres waste in a laboratory fixed bed batch reactor. The results regarding the influence of either the reaction temperature (425, 450, 475, and 500 °C) and the flow of the inert gas (0, 100, 300, and 500 mL/min) on products yield (referred to pyrolysis of waste tyres) are also considered and discussed. On the basis of the above mentioned findings, the most appropriate experimental conditions were selected to contribute to a higher yield of pyrolysis oil. The sample of pyrolysis oil obtained from the experiments carried out in the selected optimal conditions (reaction time 120 min, temperature 450 °C and the inert gas flow of 100 mL/min) was subjected to a calorimetric and infrared spectroscopy analysis. The results of IR spectroscopy analysis on this oil sample showed the following content in percentages (by mass): 32.59 % of aromatics, 51.06 % of paraffins and 16.35 % of naphthenes. The pyrolysis oil so obtained has a high calorific value (42 MJ/kg) and a low sulfur content (0.41 % by mass), which makes it an excellent raw material for energy production. The solid product, i.e. pyrolysis char or carbon black, has the potential to be used as an adsorbent or catalyst support after an activation process, which changes its irregular pore structure to a more voluminous one, making the overall structure more crystalline and symmetrical. Pyrolysis coal has a fairly high calorific value of 31 MJ/kg, when compared to typical solid fuels, so it can be used in energy production or as a feedstock for the gasification process.

A nuclear reactor leak is undesirable and unpredictable occurrence in the plant of nuclear energy generation. For this reason, an accurate equipment is needed to inspect and supervise reactors. There are two kind of reactors for research and industry reactors, both of them are needed to inspect. Concern to inspection, regularly check is needed to ensure reactor conditions are always safe to operate. For that reason, an application of advanced technology for detecting leaks is priority. In this research, we are using underwater robot to be implemented. Using the robot is able to detect periodically, continuously with accurate reports to the operator or reactor supervisor. Furthermore, Underwater Robot namely Robaru, with 4 propellers equipped at the robot, Robaru can move on 3 axes x, y and z and rotate. The use of cameras, as well as temperature measurements to obtain data when conducting inspections of the reactor. The survey method used is direct observation to detect leaks. The robot is at a certain distance by following a predetermined connection or path. The robot has successfully performed a good check with an accurate level of positioning accuracy.

Proximal tubular epithelial cells (PTEC) are constantly exposed to potentially toxic metabolites and xenobiotics. The regenerative potential of the kidney enables the replacement of damaged cells either via the differentiation of stem cells or the regain of proliferative properties of the PTEC. Nevertheless, it is known that renal function declines, suggesting that the deteriorated cells are not replaced by fully functional cells. To understand the possible causes of this loss of kidney cell function, it would be beneficial to understand the role of toxins during the regeneration process. Therefore, we investigated the sensitivity and function of human induced pluripotent stem cells (hiPSC), hiPSC differentiating, and hiPSC differentiated into proximal tubular epithelial-like cells (PTELC) to known nephrotoxins. hiPSC were differentiated into PTELC, exhibiting a similar morphology to PTEC, expressing prototypical PTEC markers and performing albumin endocytosis. When treated with two nephrotoxins, hiPSC and differentiating hiPSC were more sensitive to cisplatin than differentiated PTELC, whereas all stages were equally sensitive to cyclosporin A. Both toxins also had an inhibitory effect on albumin uptake. Our results suggest a high sensitivity of differentiating cells towards toxins, which could have an unfavorable effect on regenerative processes. To study this, our model of hiPSC differentiating into PTELC appears suitable.

The article aims to find potential biomarker for the detection of tubular damage in pediatric neurogenic bladder (NB) by investigating urinary levels of liver-type fatty acid-binding protein (uL-FABP). This prospective analysis was conducted on two groups: 42 children with NB and 18 healthy children. The uL-FABP concentrations were measured using ELISA methods. The children’s medical charts were analyzed to determine age, sex, anthropometric measurements, activity assessment using Hoffer’s scale and renal function parameters. The results revealed that the uL-FABP/creatinine ratio was higher in the studied group compared with the reference group. A significant positive correlation between uL-FABP and proteinuria was found. Children with a history of vesicoureteral reflux (VUR) tended to have elevated uL-FABP. In conclusion, uL-FABP may be considered a potential tubular damage biomarker in children with NB. Proteinuria and history of VUR may be the factors influencing uL-FABP.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

Let $(Omega, mu)$ be a measure space and $\{\tau_\alpha\}_{\alpha\in \Omega}$ be a normalized continuous Bessel family for a real Hilbert space $\mathcal{H}$. If the diagonal $\Delta \{(\alpha, \alpha):\alpha \in \Omega\}$ is measurable in the measure space $\Omega\times \Omega$, then we show that \begin{align}\label{CRBA} \sup _{\alpha, \beta \in \Omega, \alpha\neq \beta}\langle \tau_\alpha, \tau_\beta\rangle \geq \frac{-(\mu\times\mu)(\Delta)}{(\mu\times\mu)((\Omega\times\Omega)\setminus\Delta)}. \end{align} We call Inequality (1) as continuous Rankin bound. It improves 76 years old result of Rankin [Ann. of Math., 1947]. It also answers one of the questions asked by K. M. Krishna in the paper [Continuous Welch bounds with applications, Commun. Korean Math. Soc., 2023]. We also derive Banach space version of Inequality (1).

We prove the continuous non-Archimedean (resp. p-adic) Banach space and Hilbert space versions of non-Archimedean (resp. p-adic) Welch bounds proved by M. Krishna. We formulate continuous non-Archimedean and p-adic functional Zauner conjectures.

Liquorpheresis (CSF filtration) comprises a therapeutical approach that has been proposed to treat several neurological conditions where antibodies, inflammatory mediators or abnormal peptides are the cause or play an important role in the pathogenesis of the disease. CSF replacement may be an alternative approach not explored so far. Here, we review previous experiences in the use of liquorpheresis in autoimmune and degenerative neurological diseases. Then we describe previous developments and provide some new technical innovations in order to design bidirectional CSF shunting systems. These systems can be complemented either with a deposit of artificial CSF or with a CSF filter, allowing CSF replacement or liquorpheresis respectively. Both options would lead to mechanical dilution of the patient’s CSF.

Biofilm serves as the residence for bacteria, wherein bacteria attach to surfaces and produce extracellular polymeric substances, including proteins, polysaccharides, and extracellular DNA. In recent years, biofilm reactors have gained increasing significance, playing a crucial role, for instance, in immobilizing heavy metals from waterways. This paper employs a bibliographic study to analyze the most important keywords and organizations in the field of biofilm reactors, identifying recent significant papers. Additionally, the paper discusses the opportunities for the future development of biofilm reactors. Through this study, a better understanding of key factors in biofilm reactor research is achieved, providing valuable guidance for future studies and applications in this field.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

Calcium and magnesium are important not only for human health, but also for reducing problems related to the corrosive and aggressive effects of soft water on drinking water distribution materials. Experimental and mathematical modeling of the recarbonization process aimed at increasing the content of these biogenic elements in water was carried out using the novelty of a continuous laboratory and pilot scale fluidized bed reactors. Water remineralization using half-calcined dolomite (HCD) and carbon dioxide was used. The influence of operating conditions Q(CO2), freshwater inflow and HCD dose on quality indicators of treated drinking water (c(Ca2+), c(Mg2+), c(Ca2++Mg2+) and Ca/Mg) was studied. The results show that the concentration of Mg2+ is more significantly affected by the amount of HCD in the system and the flow of CO2. The influence of freshwater inflow on the Mg2+content is to a lesser extent. At a constant CO2 flow, therefore, as the tap water inflow increases, the Ca2+ content decreases and the Mg2+ content increases, which has results in a decrease in the Ca/Mg molar ratio. However, the Ca/Mg ratio can be effectively controlled by adding an appropriate amount of HCD at certain time intervals. Overproduction of ions is easily controlled by CO2 flow.

During the long-term operation of the plasma reactor, decreases in the plasma concentration were noticed despite the constant maintenance of all parameters. One of the factors is the decrease of the nitrogen content on the surface of the electrode, in order to eliminate it, the supply voltage has been increased to 11 kV. The next decisive factor in the decrease of plasma concentration is the oxidation of the electrode surface, therefore two electrodes were used: first one with solid gold and the other one copper covered with galvanized gold with a thickness of 10 μm. During the experiment, a large decrease in plasma concentration was observed when the electrode coated by gold was used. High-energy electrons have knocked out the gold atoms from the electrode, as a result of which the gold evaporated and the raids layers formed. After a month of working of the electrodes, metallographic researches were carried out, the results of which are described in this publication.

Background: Early postoperative airway management after laryngo-tracheal surgery is crucial. Acute respiratory failure due to glottis’ oedema may occur, requiring reintubation. This can prolong ventilatory assistance, jeopardizing the anastomosis. To date, only judicious steroid administration and fluid management are available to avoid more invasive procedures. High-Flow-Oxygen-Therapy(HFOT) is a noninvasive O2 support method providing humidification, warmed air, Positive-End-Expiratory-Pressure(AIRVO2). No data exist about HFOT use to prevent early complications after laryngo-tracheal surgery. Methods: Between Sept.2020-Sept.2022, 107 consecutive patients underwent laryngo-tracheal surgery received HFOT(Group A). Data and long-term results were compared with those of 80 patients operated between Sept.2018-Aug.2020(Group B), when HFOT was not available. All patients were operated in a single center. No pre- or post-operative settings changed, except for HFOT introduction. We analyzed and compared the risk for “delayed” reintubation (unexpected reintubation within the first 24-48 hours after extubating/laryngeal mask removal) in the two groups. Results: No patients reported HFOT-related adverse events. Control group(B) presented “delayed” reintubation in 37% (p= 0.027), Intensive Care Unit admission in 67%(p=0.005) and longer hospital stay(p=0.001) compared to HFOT group(A). Minor complications rate was 3% in both group and overall mortality was 0%. Re-stenosis was described in 4.6% of HFOT group, without a statistically significant difference (p=0.7006). Conclusions: Our study is the first to investigate HFOT use in patients undergoing laryngo-tracheal surgery, potentially representing a consistent innovation in the peri-operative management of these patients. With the limit of a retrospective series, we would suggest HFOT use for preventing post-operative reintubation rate, possibly reducing ICU admission and hospital stay.

Electrospinning is known to be an effective and straightforward technique to fabricate polymer non woven matrices made of nano and microfibers. Micro patterned morphology of electrospun matrices results to be outmost advantageous in the biomedical field, since it is able to mimic extracellular matrix (ECM), and favors cell adhesion and proliferation. Controlling electrospun fibers alignment is crucial for the regenerative purposes of certain tissues, such as neuronal and vascular. In this study we investigated the impact of electrospinning process parameters on fiber alignment in tubular nanofibrous matrices made of Poly (L-lactide-co-ε-caprolactone) (PLA-PCL); a Design of Experiments (DoE) approach is here proposed in order to statistically set up the process parameters. The DoE was studied keeping constants the previously set material and environmental parameters; voltage, flow rate and mandrel rotating speed were the process parameters here investigated as variables. Orientation analysis was based on ImageJ and plugin Orientation J analysis of SEM images. The results show that voltage combined with flow rate has significant impact on electrospun fiber orientation, and the greatest orientation is achieved when all the three input parameters (voltage, flow rate and mandrel rotation speed) are at their maximum value.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

After a long a glorious history, marked by the first direct proofs of neutrino existence and of the mixing between the first and third neutrino generations, the reactor antineutrino experiments are still well alive and will continue to give important contributions to the development of elementary particle physics and astrophysics. In parallel to the SBL experiments, that will be dedicated mainly to the search for sterile neutrinos, a new kind of experiments will start playing an important role: the medium baseline reactor experiments, aiming to study the neutrino mass ordering. The first example of this kind, the liquid scintillator JUNO experiment, characterized by a very high mass and unprecedented energy resolution, will soon start data taking in China. Its main aspects are discussed here, together with its potentialities for what concerns the mass ordering investigation and also the other issues that can be studied with this detector, spanning from the accurate oscillation parameter determination, to the study of solar neutrinos, geoneutrinos, atmospheric neutrinos and neutrinos emitted by supernovas and to the search for signals of potential Lorentz invariance violation.

We monitored the water quality and hydrological conditions of a horizontal subsurface constructed wetland (HSSF-CW) in Beijing, China, for 2 years. We simulated the area rate constant and the temperature coefficient with the first-order kinetic model. We examined the relationships between the nitrogen (N) removal rate, N load, seasonal variations in the N removal rate, and environmental factors, such as the area rate constant, temperature, and dissolved oxygen (DO). The effluent ammonia (NH₄⁺-N) and nitrate (NO₃⁻-N) concentrations were significantly lower than the influent concentrations (p<0.01, n=38). The NO₃⁻-N load was significantly correlated with the removal rate (R²=0.9566, p<0.01), but the NH^₄+-N load was not correlated with the removal rate (R²=0.0187, p>0.01). The area rate constants of NO₃⁻-N and NH₄⁺-N at 20 °C were 27.01±26.49 and 16.63±10.58 m∙yr⁻¹, respectively. The temperature coefficients for NO₃⁻-N and NH₄⁺-N were estimated at 1.0042 and 0.9604, respectively. The area rate constants for NO₃⁻-N and NH₄⁺-N were not correlated with temperature (p>0.01). The NO₃⁻-N area rate constant was correlated with the corresponding load (R²=0.9625, p<0.01). The NH₄⁺-N area rate was correlated with DO (R²=0.6922, p<0.01), suggesting that the factors that influenced the N removal rate in this wetland met Liebig's law of the minimum.

Glycerol represents a useful functional component of heat-transfer fluids. Glycerol is known to be triboelectrically active. We report how the flow of glycerol, stopped in a cylindrical coiled pipe, influences horseradish peroxidase (HRP) enzyme. Namely, glycerol flow was pumped through the coil and then stopped. After that, we incubated the 0.1 µM solution of HRP near the side of the coil, and then adsorbed HRP onto mica. This operation markedly increased the HRP aggregation on mica in comparison with the control sample. We explain this phenomenon by the influence of triboelectrically induced electromagnetic fields. Our results can be useful in the development of flow-based systems for biosensors and bioreactors.

Let $(\Omega, \mu)$, $(\Delta, \nu)$ be measure spaces. Let $(\{f_\alpha\}_{\alpha\in \Omega}, \{\tau_\alpha\}_{\alpha\in \Omega})$ and $(\{g_\beta\}_{\beta\in \Delta}, \{\omega_\beta\}_{\beta\in \Delta})$ be continuous 1-Schauder frames for a Banach space $\mathcal{X}$. Then for every $x \in \mathcal{X}\setminus\{0\}$, we show that \begin{align*} \mu(\operatorname{supp}(\theta_f x)) \geq \frac{1}{\displaystyle\sup_{\alpha \in \Omega, \beta \in \Delta}|f_\alpha(\omega_\beta)|}, \quad \nu(\operatorname{supp}(\theta_g x))\geq \frac{1}{\displaystyle\sup_{\alpha \in \Omega , \beta \in \Delta}|g_\beta(\tau_\alpha)|}. \end{align*} where \begin{align*} &\theta_f: \mathcal{X} \ni x \mapsto \theta_fx \in \mathcal{L}^1(\Omega, \mu); \quad \theta_fx: \Omega \ni \alpha \mapsto (\theta_fx) (\alpha):= f_\alpha (x) \in \mathbb{K},\\ &\theta_g: \mathcal{X} \ni x \mapsto \theta_gx \in \mathcal{L}^1(\Delta, \nu); \quad \theta_gx: \Delta \ni \beta \mapsto (\theta_gx) (\beta):= g_\beta (x) \in \mathbb{K}. \end{align*} This solves a problem asked by K. M. Krishna in the paper 'Functional Continuous Uncertainty Principle' \textit{[arXiv:2308.00312v1]}.

Recently, SMR (Small Modular Reactor) is expected to be able to operate flexibly in conjunction with a high renewable energy penetration grid as a result of improved safety and easy power control compared to large nuclear power plants. SMRs such as South Korea’s System-integrated Modular Advanced ReacTor (SMART) are designed to use canned motors (CMs) for their reactor coolant pumps (RCPs) to enhance safety. The CMs passively enhance the reactor’s safety by preventing leakage of radioactive reactor coolant. However, with motor sizes designed to be as small as possible, and the increased air gap of CMs between stator and rotor, starting torque may be insufficiently small compared to that of similar sized induction motors (IMs). Thusly, CMs may require variable frequency drives (VFDs) to start. This paper compares the torque characteristics of CMs with those of IMs for SMART’s RCPs. ETAP is then used to perform motor starting analysis for CMs started with and without VFDs. The results are presented and analyzed to find out if the VFDs deal with the CM starting torque issue.

The objective of this paper is to investigate the debonding behavior of the interface between continuously and discontinuously fiber reinforced thermoplastics using the climbing drum peel test. The study emphasizes the importance of considering different climatic boundary conditions due to the properties of thermoplastics. Specimens with varying moisture contents are prepared and tested. It is observed that an increase in moisture content initially results in a higher fracture surface energy being required to separate the two materials, but a further increase results in a decrease of the required energy. The study presents an explanatory model of increasing plasticization of the polymer due to increased polymer chain mobility, which results in more deformation energy being required to propagate the crack. The experiment is also modeled numerically for the first time with cohesive surfaces, which successfully reproduces the force-displacement curve in the experiment.

This study aimed to verify the effects of an acute increase in blood pressure (BP) and/or renal sympathetic nerve activity (rSNA) on the renal excretion of sodium and water and its potential effect on the regulation of NHE3 activity. Uninephectomized anesthetized male Wistar rats were divided into three experimental groups: 1) Sham, the rats had their BP and rSNA recorded, and urine was collected for 2 h; 2) bicuculline (Bic) paraventricular nucleus of the hypothalamus (PVN), rat BP, and rSNA were recorded, and urine was collected for 1 h at baseline conditions and 1 h after bicuculline injection into the PVN; 3) RNS + Bicuculine injection into the PVN, BP, and rSNA were recorded, and urine was collected 1h after RNS and 1 h after bicuculline injection into the PVN. Renal nerve stimulation (RNS) decreased sodium and water excretion independent of changes in BP. However, after Bic in the PVN during RNS stimulation, BP and rSNA increased up to 30% and 60%, respectively, increasing diuresis (5-fold) and natriuresis (2.3-fold), accompanied by a significant reduction in the NHE3 activity independent of GFR changes. In conclusion, an acute increase in BP overcomes such effects, generating diuresis, natriuresis, and NHE3 activity inhibition.

Sustainable continuous cover forestry is defined and analyzed in several ways. The differential equation representing growth of the basal areas of individual trees, motivated by fundamental biological production theory by Lohmander (2017a), is analyzed and extended in different directions. From the solution of the differential equation, the basal area and the tree diameter are obtained as explicit functions of time. The diameter is a strictly increasing function of time. In the absence of competitors, the diameter increment is shown to be a strictly decreasing function of time. Hence, the diameter increment can also be interpreted as a strictly decreasing function of the diameter. Alternative forms of adjustment of the differential equation, with consideration of competition, are defined. If the competition is strong, with large trees in the vicinity of a particular tree, then the basal area increment, and the diameter increment, are reduced. The growth of a large tree is less sensitive than the growth of a small tree, to competition from other trees. Under strong competition, the basal area increment, and the diameter increment, are strictly concave functions of the size of the tree. The unique maximum of the diameter increment occurs at a higher diameter, if the competition increases. In dynamic equilibrium, the tree size frequency distribution is stationary. If natural tree mortality can be avoided via the harvest strategy, the tree size frequency distribution is a function of the size and competition dependent growth function, and the harvest strategy. Empirical tree size frequency data are used to simultaneously estimate parameters of a size and competition dependent growth function and the applied harvest strategy, via nonlinear optimization. The properties of the estimated growth function are consistent with the corresponding properties of the production theoretically motivated hypothetical function, and the properties of the estimated harvest strategy confirm the corresponding hypotheses. The R2 of the nonlinear regression exceeds 0.97. With access to an empirically estimated equilibrium tree size distribution, it is possible to: 1. Estimate size frequency relevant parameters of tree size and competition dependent growth functions for individual trees. 2. Estimate the applied harvest strategy. 3. Explain and reproduce the empirically estimated tree size equilibrium distribution.

Chipman contends, in stark contrast to the conventional view, that utility is not a real number but a vector and is inherently lexicographic in nature. According to these views, it will be proved that, for every preordered topological space (X,≾,t), the assumption t to be finer than the order topology t≾ on (X,t), i.e. t⊇t≾, and the assumption the quotient topology t∣∼≾ that is defined on the preordered set (X∣∼,≾∣∼) of indifference classes of ≾ to be Hausdorff imply that a cardinal number κ and a (complete) preorder ≲ on {0,1}κ that is coarser than the lexicographical ordering ≤lex on {0,1}κ, i.e. ≤lex⊂≲, can be chosen in such a way that there exists a continuous order-embedding ϑ:(X,≾,t)⟶({0,1}κ,≲,t≤lex). This theorem will be compared with a theorem that, in particular, describes necessary and sufficient conditions for ≾ to have a continuous multi-utility representation.

The World Health Organization(WHO) in 2016 considered mHealth as: “the use of mobile wireless technologies including smart devices such as smartphones and smartwatches for public health” as an important resource for health services delivery and public health given their ease of use, broad reach and acceptance. WHO emphasizes the potential of this technology to increase access to health information, services and skills as well as promoting positive changes in health behaviors and management of diseases. In this regard, the capability of smartphones and smartwatches for m-health monitoring as well as verification of the patient the signal has become an important component of mHealth system. Most of the smartwatches could extract more than one bioelectrical signal therefore, therefore they provide suitable platform for extracting health data for e-monitoring. The existing approaches have not considered the integrity of data obtained from these smart devices. Therefore, it is important that the integrity of the collected data be verified continuously through user authentication. This could be done using any of the bioelectrical signals extracted and transmitted for e-monitoring. In this article, a smartwatch is used for extracting bioelectrical signal before decomposing the signal into sub-bands of Detail and Approximation Coefficient for user authentication. To select suitable features using biorthogonal wavelet decomposition of signal from a non-intrusive extraction, a detailed experiment is conducted extracting suitable statistical features from the bioelectrical signal from 30 subjects using different biorthogonal wavelet family. Ten features are extracted using Biorthogonal wavelet to decompose the signal into three levels of sub-band Detail and Approximation Coefficient and features extracted from each level the decomposed Detail and Approximation Coefficients. Comparison analysis is done after the classification of the extracted features based on the Equal Error Rate (EER). Using Neural Network (NN) classifier, Biorthogonal Wavelet Detail Coefficient Sub-band level 3 of bior1.1 achieved the best result of EER 13.80% with the fusion of the best sub-band three levels of bior1.1 achieving a better result of 12.42% EER.

The correlation and comorbidity between depression and chronic pain have been observed for a long time. Generally, it is considered that the two conditions reinforce each other, whereas the causal relationship between them is not clear. However, some evidence suggested that chronic pain may reverse the progression of depression in some cases. This article presents a selective review of clinical and pharmacological relationship between depression and pain, and their interactions at neurochemical and neurobiological levels. In addition, we open a discussion on a recent case report of repeated success of using short but continuous pain (SCP) during meditation as the only treatment for depression, compared to initial success but no remission with other conventional antidepressants on the same patient. Together this review proposes an updated model for depression and its various treatments that is based on synaptic and system homeostasis. More importantly, it suggests that SCP may benefit depression recovery through its properties that are different from either acute or chronic pain and represents a novel research area that has been largely neglected to date.

The workplace is an ideal setting for health promotion. The regular medical examination of workers enables us to screen for numerous diseases, spread good practices and correct lifestyles, and obtain a favourable risk/benefit ratio. The continuous monitoring of the level of workers' wellbeing using a holistic approach that goes beyond the simple prevention of occupational risks enables us to promptly identify problems in work organization and the company climate. Problems of this kind can be adequately managed by using a participatory approach. In this study participatory ergonomics groups were used to improve occupational life in a small company. After intervention we observed a reduction in levels of perceived occupational stress measured with the effort / reward imbalance model, and an improvement in psychological wellbeing assessed by means of the Goldberg anxiety / depression scale. Although the limited size of the sample calls for a cautious evaluation of this study, the GEP© strategy proved to be a useful tool due to its cost-effectiveness.

Ammonia known as harmful gas that could impact on health and environment. Typically, ammonia gas emitted by fertilizer industry, rubber factory, etc. There are many options for advance industry to control ammonia gas pollution, absorption tower using water scrubber and using activated carbon as adsorption reaction could be an option. But for middle- and lower-class industry, it is common in Indonesia, as seen on many rubber factories, ammonia gas pollution is serious problem to control, actually they have used wet scrubber but eficiency is lower about 47%. This study measure performance for ammonia elimination as gas pollutant using absorption tower and adsorption tower in laboratory scale. Using electrochemical gas sensor, we measure both ammonia concentration for inlet and outlet simultaneously to settle saturation point of these two types of ammonia emission control. In conclusion, Ammonia absorbed in water proportional to saturation time and absorbent volume. Highest absorbed ammonia concentration 1.538 mg/L on 4000 mL absorbent. For Adsorption system, saturation time proportional and correlated to adsorbent weight and Adsorption capacity reverse correlated to adsorbent weight. Optimum adsorption point can be achieved from intersection curve between saturation time and adsorption capacity which is 1200 grams adsorbent

Researchers from around the world are looking for better and cheaper ozone production. One of the methods increasing the efficiency of ozone production is the use to a rotating electrode presented in this paper. Experiments were carried out which shows that the most important parameters are the materials used on the electrodes and the condition of its surface. The metallographic investigations of the electrodes after continuous monthly work was made, which show how the raids layers are formed. As a result of working in a highly oxidizing environment, the electrode is oxidized in the process of chemical corrosion. It is obvious that the layer of corrosion products created during the work of the plasma reactor isolates the surface of the electrode, which reduces the intensity of the electric field, causing a decrease in the amount of plasma generated, which is a direct cause of lowering the concentration of ozone during this process. The dynamics of plasma generation process and the type of electrode material working in changing process conditions are the decisive factors influencing the concentration of ozone produced. The influence of the medium, which is the electrode material, depends mainly on its resistance to corrosion in the environment of dynamically changing conditions, e.g. electrode rotation, oxygen flow through the rotating electric field and the long monthly working time of the plasma reactor.

Non steady applied magnetic field impact on a liquid metals has good prospects for industry. For a better understanding of heat and mass transfer processes under these circumstances, numerical simulations are needed. A combination of finite elements and volumes methods was used to calculate the flow and solidification of liquid metal under electromagnetic influence. Validation of numerical results was carried out by means of measuring with ultrasound Doppler velocimetry technique, as well as with neutron radiography snapshots of the position and shape of the solid/liquid interface. As a result of the first part of the work, a numerical model of electromagnetic stirring and solidification was developed and validated. This model could be an effective tool for analyzing the electromagnetic stirring during the solidification process. In the second part, the dependences of the velocity pulsation amplitude and the melt velocity maximum value on the magnetic field pulsation frequency are obtained. It was found numerically the ability of the pulsating force action to develop higher values of the liquid metal velocity at a frequency close to the MHD resonance. Obtained characteristics give a more detailed description of the electrically conductive liquid behaviour under action of pulsating traveling magnetic field.

Gravitational waves have been detected in the past few years from several transient events such as merging stellar mass black holes, binary neutron stars, etc. These waves have frequencies in a band ranging from a few hundred hertz to around a kilohertz to which LIGO type instruments are sensitive. LISA would be sensitive to much lower range of frequencies from SMBH mergers. Apart from these cataclysmic burst events, there are innumerable sources of radiation which are continuously emitting gravitational waves of all frequencies. These include a whole mass range of compact binary and isolated compact objects as well as close planetary stellar entities. In this work, quantitative estimates are made of the gravitational wave background produced in typical frequency ranges from such sources emitting over a Hubble time and the fluctuations in the h values measured in the usual devices. Also estimates are made of the high frequency thermal background gravitational radiation from hot stellar interiors and newly formed compact objects.

In the wake of the rapid deployment of Small Modular Reactors (SMRs), this study aims to enhance the efficiency, reliability, and safety of SMR operations through a deeper understanding of human factors in their interaction within digital control room systems. Recognizing the pivotal role of human understanding in this new era of nuclear power, we employed electroencephalogram (EEG)-based monitoring to provide an unparalleled real-time view into operators' cognitive states. By interfacing detailed human models, informed by EEG metrics, with specific operational tasks, we recreate potential operational scenarios using an SMR simulator and capture intricate human responses therein. Our results elucidated the intricate relationship between EEG-derived data and human performance shaping factors, indicating a marked correlation between certain EEG patterns and operational efficiencies. Conclusively, these findings underscore the potential of EEG monitoring not only as a diagnostic tool but as an instrumental aid in the design and operation of future SMR digital control rooms. The insights derived offer a roadmap for the development of practical strategies, ensuring more effective and safer SMR operations.

In the evolving landscape of pharmaceutical manufacturing, a comprehensive continuous production process is being crafted for small-scale active pharmaceutical ingredient production. This study focuses on continuous crystallization with separate nucleation and crystal growth units, as well as continuous downstream processing, encompassing filtration, washing, and drying until the formation of free-flowing particles. We introduce a novel continuous nucleator designed based on solubility data and produced via 3D printing, enabling a fast and precise small-scale manufacturing of a nucleator meeting the requirements for nucleation and for the further growth processes. The nucleator was evaluated with regard to its suitability for continuous long-term operation across various coupled crystallizers. As a practical application example it is connected to a slug flow crystallizer to enable high-quality continuous crystallization. Additionally, the full integration of downstream processes using the continuous vacuum screw filter to achieve free-flowing product particles is realized. Even under non-optimized process conditions, with the help of in-situ generation of nuclei free-flowing product particles were successfully obtained. This is particularly useful during drug development when no material is available for seed addition and quickly obtain product for further characterization.

This study explored the feasibility of fluoride removal from simulated semiconductor industry wastewater and its recovery as calcium fluoride using fluidized bed crystallization. The continuous reactor showed best performance (>90% fluoride removal and >95% crystallization efficiency) at a calcium to fluoride ratio of 0.6 within first 40 days of continuous operation. The resulting particle size increased by more than double during this time along with a 36% increase in the seed bed height indicating deposition of CaF2 onto the silica seed. The SEM-EDX analysis showed the size and shape of the crystals formed along with high amount of Ca-F ions presence. The purity of the CaF2 crystals were determined to be 91.1% though ICP-OES analysis. Following the continuous experiment, different process improvement strategies are explored. The addition of excess amount of calcium resulted in an additional 6% fluoride removal, however, compared to this single stage process, a two-stage approach was found to be better strategy to achieve a low effluent fluoride concentration. The fluoride removal reached 94% with this two-stage approach under optimum condition of 4 + 1 h HRT combinations and a [Ca2+]/[F-] ratio of 0.55 and 0.7 for the two reactors, respectively. CFD simulation showed the impact of inlet diameter, bottom-angle shape and width and height ratio of the reactor on mixing inside reactor and possibility of further improvement in reactor performance by optimizing the FBR configuration.

The present study shows a methodology for analyzing and designing a cylindrical packed-bed reactor considering stationary and dynamic models. The design comprises the reactor's stationary and dynamic governing differential equations for mass and heat transfer under multi-dimensional approaches. The results included simulation of concentration, temperature, and reaction rate profiles via the 1-D and 2-D differential equations solution with FlexPDE software. The analysis was complemented with a scaled 3-D dynamic model implemented in COMSOL Multiphysics. Both FlexPDE and COMSOL Multiphysics relied on the finite element technique to solve the governing differential equations. The simulated concentration and temperature profiles from both FlexPDE and COMSOL models were compared to experimental data gathered from literature (specifically from a Fischer-Tropsch process to produce low-molecular-weight hydrocarbons in a configuration of cylindrical packed-bed reactors). Simulated concentration and temperature profiles from the 2-dimensional dynamic model and the COMSOL model were in good agreement with the trend observed in experimental data. Finally, the predicted reaction rate profiles from the COMSOL model and the 2-dimensional dynamic model followed the temperature trend, thus reflecting the temperature dependence of the reaction.

Background: Nowadays vital signs in clinics are electronically monitored excepted for urine output which still requires, manual recording, which is subject to human errors. We, in-vitro, assessed in this study the ability a novel electronic device to measure by a combination of two different methods, the real time flow-output, like urine output. Methods: Flow or urine output was measured by a combination technique of gravimetry using a dynamometer and capacitive sensing to improve precision. Data were obtained in 3 different situations, low, medium, and high flow. Results: Three different situations were tested: full or empty dead space and Pasteur’s chamber. The differences between the injected and measured volume varies from 0 to 5 ml representing a maximal error of 3 % regardless of the volume injected and the flow in ml/hour. The capacitive sensors behave as expected with a parallel curve of the expected and measured flow. Conclusion: We have shown in this in-vitro study that the combination of gravimetry and capacitive sensors analysis allow accurate measurement of volume and flow-output. Clinical trials should be conducted to confirm its usefulness in urine output measurement in the real life.

High-energy small electron beams generated by linear accelerators are used for radiotherapy of localized superficial tumors. The aim of the present study is to assess the dosimetric performance under small radiation therapy electron beams of the novel PTW microSilicon detector by comparison with commercially available dosimeters. Relative dose measurements of circular fields with 20, 30, 40 and 50 mm aperture diameters were performed for 4 to 12 MeV energy range of electron beams generated by an Elekta Synergy linac. Percentage depth dose, transverse profiles and output factors normalized to the 10 × 10 cm2 reference field were measured. All dosimetric data were collected in a PTW MP3 motorized water phantom at SSD of 100cm by using the novel PTW microSilicon detector. The PTW diode E and the PTW microDiamond were also used in all beam aperture for benchmarking. Data for the biggest field size were also measured by the PTW Advanced Markus ionization chamber.Measurements performed by the microSilicon are in good agreement with the reference values for all the tubular applicators and beam energies, within the stated uncertainties. This confirms the reliability of the microSilicon detector for relative dosimetry of small radiation therapy electron beams collimated by tubular applicators.

In today’s fast paced, attention-demanding society, executive functions and attentional resources are often taxed. Individuals need ways to sustain and restore these resources. We first review the concepts of attention and restoration, as instantiated in Attention Restoration Theory (ART). ART emphasizes the role of nature in restoring attention. We then discuss essentials of experiments on the causal influences of nature. Next, we expand the concept of ART to include modern, designed environments. We propose a wider perspective termed attentional ecology, in which attention behavior is viewed within a larger system involving the human and their interactions over time with environmental demands. When the ecology is optimal, mental functioning can be a positive “flow” that is productive, sustainable for the individual, and sometimes creative.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

(1) Background: The chemotherapeutic drug cisplatin exerts toxic side effects causing acute kidney injury. Mesenchymal stromal cells can ameliorate cisplatin-induced kidney injury. We hypothe-size that the MSC secretome orchestrates the vicious cycle of injury and inflammation by acting on proximal tubule epithelial cells (PTECs) and macrophages individually, but further by coun-teracting their cellular crosstalk. (2) Methods: Conditioned medium (CM) from adipose stromal cells was used, first assessing its effect on cisplatin injury in PTECs. Second, effects of cisplatin and CM on macrophages were measured. Lastly, in an indirect co-culture system the interplay between the two cell types was assessed. (3) Results: First, CM rescued PTECs from cisplatin-induced apoptosis by reducing oxidative stress and expression of nephrotoxicity genes. Second, while cisplatin exerted only minor effects on macrophages, CM skewed macrophage phenotypes to the anti-inflammatory M2-like phenotype and increased phagocytosis. Finally, in the co-culture system, CM suppressed PTEC death by inhibiting apoptosis and nuclei fragmentation. CM lowered TNF-α release. While cisplatin inhibited macrophage phagocytosis, PTECs, and CM to a greater extent, enhanced it. CM strongly dampened the inflammatory macrophage cytokine secretion triggered by PTECs. (4) Conclusion: ASC-CM surpasses the PTEC-macrophage cross-talk in cisplatin injury. The positive effects on reducing cisplatin cytotoxicity, on polarizing mac-rophages and on fine-tuning cytokine secretion underscores MSCs CM benefit to prevent kidney injury progression.

The rapid growth of smartphone financial services raises the need for secure mobile authentication. Continuous authentication is a user-friendly way to strengthen the security of smartphones by implicitly monitoring a user’s identity through sessions. Mobile continuous authentication can be viewed as an anomaly detection problem in which models discriminate between one genuine user and the rest of the imposters (anomalies). In practice, complete imposter profiles are hardly available due to the time and monetary cost, while leveraging genuine data alone yields poor generalized models due to the lack of knowledge about imposters. To address this challenge, we recast continuous mobile authentication as a few-shot anomaly detection problem, aiming to enhance the inference robustness of unseen imposters by using partial knowledge of available imposter profiles. Specifically, we propose a novel deep learning-based model, namely Local Feature Pooling based Temporal Convolution Network (LFP-TCN), which directly models raw sequential mobile data, aggregating global and local feature information. In addition, we introduce a random pattern mixing augmentation to generate class-unconstrained imposter data for the training. The augmented pool enables characterizing various imposter patterns from limited imposter data. Finally, we demonstrate practical continuous authentication using score-level fusion, which prevents long-term dependency or increased model complexity due to extended re-authentication time. Experiments on two public benchmark datasets show the effectiveness of our method and its state-of-the-art performance.