This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

In this research paper, a high gain transformer less inverter modeling which is used for the smart grid technology or as the stand alone for home appliances is proposed. The proposed transformer less topology provides a higher voltage gain, low cost, small size and simple control stand alone transformer less inverter for home appliances. The above inverter is modeled by using software which is known as MATLAB/ Simulimk.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

In this contribution a new configuration of a DC-DC Boost and Buck-Boost converters is proposed to track sinusoidal signals exactly, with zero tracking error. The stage is conformed by two DC-DC converters connected to the same load, this is, they are not connected in cascade. To track exactly the sinusoidal reference the control scheme is base on the indirect control algorithm and the harmonic balance method. The proposed algorithm considers a second control input with the end of cancel out the second harmonic, this second harmonic is produced by the non linearity of the model and must be cancelled since there must be a single frequency in the output. The result is such that the converters can track sinusoidal signals with exactly zero error, some numerical results are presented to corroborate the proposal.

This paper presents two control design strategies for voltage regulation in a single inductor dual output (SIDO) DC-DC Buck converter system. Based on a nominal multiple input multiple output (MIMO) plant model and performance requirements, both an LQR and a decoupled PI control laws are designed to control the power converter system, under parametric uncertainties such as voltage source variation, CPL power variation, and load resistance variation. Therefore, the SIDO converter can cascade operating, which may cause the undesired effects of voltage oscillation and reduce the system's stability margin. The control performance was assessed under both uncertainties resistive loading and power variation of a constant power load (CPL). A SIDO DC-DC Buck converter board has been developed for experimental tests. The experimental results show that the LQR strategy, compared to the PI strategy, presented a robust performance in the presence of parametric uncertainties in the resistive loads being, however, sensitive to uncertainties due to the presence of CPL loads.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

In this paper, new N-way Wilkinson power dividers (WPDs) are represented by using slow-wave structures such as narrow slits loaded and meandered transmission lines. The slit loaded and meandered lines are used to represent the quarter wavelength transmission lines of a conventional WPD for size reduction. Based on the proposed approaches, 2-, 4- and 8-way power dividers are designed, simulated and fabricated. The fabricated -, 4- and 8-way circuits have been measured at the center frequencies of 2.03, 1.77, and 1.73 GHz in an excellent agreement with the predicted ones. The meandered transmission lines are also used to design new types of WPDs having novel input/output port arrangements. For this purpose, two 3-way WPDs are located at both sides of the same board so as to have different power splitting ratios at different inputs and outputs to provide alternative solutions for antenna arrays. Furthermore, a 5-way dual layer WPD is introduced by locating the meandered transmission lines to two layers. The proposed 3- and 5-way WPDs allow halving the input power at the next output port in the order of P/2, P/4, P/8, P/16, and P/16. All of the designed power halving WPDs have been simulated, fabricated and successfully tested.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

Reliable and robust control of power converters is a key issue in the performance of numerous technological devices. In this paper we show a design technique for the control of a DC-DC buck converter with a switching technique that guarantees not only good performance but also global stability. We show that making use of the contraction theorem in the Jordan canonical form of the buck converter, it is possible to find a switching surface that guarantees stability but it is incapable of rejecting load perturbations. To overcome this, we expand the system to include the dynamics of the voltage error and we demonstrate that the same design procedure is not only able to stabilize the system to the desired operation point but also to reject load, input voltage and reference voltage perturbations.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Accurate forecasts of ocean waves energy can not only reduce costs for investment but it is also essential for management and operation of electrical power. This paper presents an innovative approach based on the Long Short Term Memory (LSTM) to predict the power generation of an economical wave energy converter named “Searaser”. The data for analyzing is provided by collecting the experimental data from another study and the exerted data from numerical simulation of searaser. The simulation is done with Flow-3D software which has high capability in analyzing the fluid solid interactions. The lack of relation between wind speed and output power in previous studies needs to be investigated in this field. Therefore, in this study the wind speed and output power are related with a LSTM method. Moreover, it can be inferred that the LSTM Network is able to predict power in terms of height more accurately and faster than the numerical solution in a field of predicting. The network output figures show a great agreement and the root mean square is 0.49 in the mean value related to the accuracy of LSTM method. Furthermore, the mathematical relation between the generated power and wave height was introduced by curve fitting of the power function to the result of LSTM method.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

This paper presents an optimal design for the inner current control loop of the continuous current conduction mode (CCM) power factor correction (PFC) stage, which it can be used as the front stage of the two stages alternating current-direct current (AC-DC) telecom power supply. Conventional single-phase CCM-PFC boost converter usually implemented with using of the proportional-integral (PI) controllers in both of the voltage and current control loops, to regulate the output DC voltage to the specified value, moreover to maintains the input current follows the input voltage which offers converter with high power factor (P.F) and low current total harmonic distortion (THD). However, due to the slow dynamic response of the PI controller at the zero-crossing point of the input supply current, input current can’t fully follow the input voltage which leads to high THD. Digitally controlled PFC converter with an optimal design of the inner current control loop using doubly control loops IP controller to reduce the THD and to offer input current with unity P.F was performed in this paper. Furthermore, for the economic design of the digitally control PFC converter, two isolated AC and DC voltage sensors are proposed and designed for the interfacing with the microcontroller unit (MCU). PSIM software was used to test the converter performance with using the proposed designed current controllers and isolated voltage sensors. High power density digitally controlled telecom PFC stage with P.F of about 99.93%, full load efficiency of about 98.70% and THD less 5.50% is achieved in this work.

Background: Nowadays vital signs in clinics are electronically monitored excepted for urine output which still requires, manual recording, which is subject to human errors. We, in-vitro, assessed in this study the ability a novel electronic device to measure by a combination of two different methods, the real time flow-output, like urine output. Methods: Flow or urine output was measured by a combination technique of gravimetry using a dynamometer and capacitive sensing to improve precision. Data were obtained in 3 different situations, low, medium, and high flow. Results: Three different situations were tested: full or empty dead space and Pasteur’s chamber. The differences between the injected and measured volume varies from 0 to 5 ml representing a maximal error of 3 % regardless of the volume injected and the flow in ml/hour. The capacitive sensors behave as expected with a parallel curve of the expected and measured flow. Conclusion: We have shown in this in-vitro study that the combination of gravimetry and capacitive sensors analysis allow accurate measurement of volume and flow-output. Clinical trials should be conducted to confirm its usefulness in urine output measurement in the real life.

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

The process model is very essential for the model based control design. The model of the process can be identified using system identification algorithm. The system identification is done through the open loop and closed loop approaches. In this work, the lab scale conical tank setup configured as a non square MIMO system. The conical tank system is identified through the both appraoches, the effectiveness and need of the both approaces are discussed. Based on the open loop identified model the controller designed and the controller implemented in the real time the to record the process data. From this data the closed loop identification are conducted uisng N4SID algorithm. The controller seetings are obtained using the smith predcitor based IMC based PI controller for the obtained model. The proposed identification algorithm and controller tuning show the better reults over the conventional method. Moreover, this method is applicable for all the non square MIMO system.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Power converters with coupled inductors are very promising due to the high efficiency and high voltage gain. Apart from the aforementioned advantages, the boost-flyback converter reduces the voltage stress on the semiconductors. However, to obtain good performance with high voltage gains, the controller must include two control loops (current and voltage), and a compensation ramp. One of the most used control techniques for power converters is the peak current-mode control with compensation ramp. However, in the case of a boost-flyback converter there is no mathematical expression in the literature, to compute the slope of the compensation ramp. In this paper, a formula to compute the slope of the compensation ramp is proposed in such a way that a stable period-1 orbit is obtained. This formula is based on the values of the circuit parameters, such as inductances, capacitances, input voltage, switching frequency and includes some assumptions related to internal resistances, output voltages, and some other electrical properties related with the physical construction of the circuit. The formula is verified numerically using the saltation matrix and experimentally using a test circuit.

This paper introduces a sliding mode control (SMC) based equivalent control method to a novel high output gain Cuk converter. An additional inductor and capacitor improves the efficiency and output gain of the classical Cuk converter. Classical PI controllers are widely used in DC-DC converters. However, it is a very challenging task to design a single PI controller operating in different load and disturbances. SMC based equivalent control method which achieves a robust operation in a wide operation range is also proposed. Switching frequency is kept constant in appropriate interval in different loading and disturbance conditions by implementing a dynamic hysteresis control method. Numerical simulations conducted on Matlab/Simulink confirm the accuracy of analytical analysis of high output gain modified Cuk converter. In addition, proposed equivalent control method is validated in different perturbations to demonstrate the robust operation in wide operation range.

Based on Venturini method, it is in favor of the modulation technique for controlling the matrix converter due to only use of the comparison between the duty cycles in time domain and the triangular carrier wave for generating the gating signals and the achievable voltage ratio between fundamental output magnitude and fundamental input magnitude to 0.866. However, even with simple modulation method and achieving maximum fundamental output magnitude, the possible input voltage unbalance conditions accordingly influence on the output performances (more reduction and distortion). Thus, a modified Venturini modulation method is presented in this paper, in order to solve the problems of unbalanced input voltage conditions on the matrix converter performances. The proposed strategy is to satisfy the desirable feature of the duty cycle modulating waves, as generated in the event of normal situation. Up to this approach, it can support either single-phase condition or two-phase condition. Performance of the proposed control strategy was verified by the simulated implementation in the MATLAB/Simulink software with showing good steady-state and dynamic operations.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

Of the roughly 20,000 canonical human protein sequences, as of September 15, 2020, 6,937 proteins have had their full or partial, medium- to high-resolution structures determined by x-ray crystallography or other methods. Which of these proteins dominate the Protein Data Bank (the PDB) and why? In this paper, we list the 273 top human protein structures based on the number of their PDB entries. This set of proteins accounts for more than 40% of all available human PDB entries and represent past trends as well as current status for protein structural biology. We briefly discuss the relationship which some of the prominent protein structures have with protein research as a whole and mention their relevance to human diseases. The top-10 soluble and membrane proteins are all well-known (most of their first structures being deposited more than 30 years ago). Overall, there is no dramatic change in recent trends in the PDB. Remarkably, the number of structure depositions has grown nearly exponentially over the last 10 or more years (with a doubling time of 7 yrs for proteins from all organisms). Growth in human protein structures is slightly faster (at 5.9 yrs, while E.Coli and Mouse+Rat protein structures accumulate more slowly, Zebrafish protein structures are growing most, at a doubling every 3.7 years, albeit starting from only approx. 100 structure entries in 2010). The information may be informative to senior scientists but also inspire researchers who are new to protein science, providing the year 2020 snap-shot for the state of protein structural biology.

Knowledge-intensive business services (KIBS) are professional services that create new added value by creating, accumulating, and disseminating new knowledge. When it comes to conducting business involving new technology, KIBS play the roles of innovator, user, and producer of new technology that has led to technological innovation. This study aimed to determine the role of KIBS as a tool for innovation in a country’s economic system. Specifically, the degree and role of their impact on the Korean economy were analyzed and compared for the entire KIBS sector, T-KIBS (a new technology-based professional service), P-KIBS (a traditional professional service), and every subsector. For this purpose, the demand-inducement model, supply inducement model, and interlinkage effects method were applied using the 2019 input-output table published in 2022. The analysis showed that the indirect production inducement effect of the entire KIBS industry on other industries was 0.800 KRW, the indirect added value inducement effect was 0.330 KRW, and the supply disruption effect was 1.144 KRW. For T-KIBS, the indirect production inducement effect was 0.687 KRW, the indirect added value inducement effect was 0.272 KRW, and the supply disruption effect was 0.730 KRW. For P-KIBS, the indirect production inducement effect was 1.472 KRW, the indirect added value inducement effect was 0.646 KRW, and the supply disruption effect was 2.657 KRW. Finally, regarding the economic ripple effect of the KIBS subsector, legal and management support services and advertisements corresponding to P-KIBS showed higher figures than the T-KIBS subsectors in all sectors, including production inducement, the added value inducement effect, and the supply disruption effect. These results revealed that in the South Korean economic system, KIBS contribute to production and value addition across all industrial sectors. It is apparent that the absence of supply significantly disrupts other industries. Furthermore, production inducement effects are evenly distributed among all the KIBS subsectors in the secondary and tertiary sectors, while the value-added effects have a greater impact on the tertiary sector. In terms of the supply shortage effects, the secondary sector experiences a more significant impact. This underscores the crucial role of KIBS in sustaining and enhancing overall economic activity in South Korea. This study is significant in that it not only investigated KIBS as an industry group using the advantages provided by industry linkage analysis but also examined and compared detailed subsectors, thereby elaborately evaluating the influence relationship between KIBS and other industries. Therefore, the results presented in this study are expected to be useful for fostering the KIBS industrial sector and establishing economic innovation policies using KIBS.

This work investigates the sliding mode control (SMC) problem for a class of uncertain switched systems subject to asynchronous switching and an assigned finite time constraint. Two important issues are how to ensure the reachability of state trajectories within the assigned time and the input-to-output finite-time stability (IO-FTS) of the closed-loop switched systems during the whole phase under asynchronous switching. To achieve these objectives, an asynchronous sliding mode controller with adjustable parameters is constructed to drive the state trajectories onto the sliding surface during the assigned finite-time interval. By means of the partitioning strategy, sufficient conditions for the IO-FTS of the closed-loop switched are derived during the whole phase [0,T] using the multiple Lyapunov function (MLF) approach. Additionally, the asynchronous characteristics are detailedly investigated while analyzing the reachability of a specified sliding surface. Finally, an illustrative example is given to illustrate the effectiveness of the proposed method.

2S-hesperidin is a flavanone (flavonoid) found in high concentrations in citrus fruits. It has an antioxidant and anti-inflammatory effect, improving performance in animals. This study investigated the effects of chronic intake of an orange extract (2S-hesperidin) or placebo on aerobic-anaerobic and metabolic performance markers in amateur cyclists. A double-blind, randomized, placebo-controlled trial was carried out between late September and December 2018. Forty amateur cyclists were randomized into two groups: one taking 500mg/day 2S-hesperidin and other taking 500 mg/day placebo (microcellulose) for 8 weeks. All participants completed the study. Performance and metabolic aerobic-anaerobic markers were measured using incremental and rectangular tests by indirect calorimetry. The anaerobic power was determined using Wingate tests. After 8 weeks supplementation, there was a significant increase in the incremental test in estimated functional threshold power (FTP) (3.23%; p≤0.05) and maximum power (2.68%; p≤0.05) with 2S-Hesperdin compared to placebo. In the rectangular test, there was a significant decrease in VO₂ (-8.26%; p≤0.01) and VO₂R (-8.88%; p≤0.01) at VT2 in placebo; however, there were no significant differences between groups. In the Wingate test, there was a significant increase (p≤0.05) in peak and relative power in both groups, but without significant differences between groups. Supplementation with an orange extract (2S-hesperdin) 500mg/day improves estimated FTP and maximum power performance in amateur cyclists.

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

In this paper, a method of charging lead acid battery with solar power by flyback converter is proposed. The basic system consists of a buffer circuit, auxiliary power circuit, control circuit, voltage feedback circuit and current feedback circuit. The system is capable of monitoring battery voltage and the current, charging the coupling inductor and automatic control of output duty cycle, overcharging and over-discharging protection. The experiment proves that the charging efficiency is improved by about 83% at full load.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Recent lines of evidence suggest the intriguing hypothesis that consuming common culinary herbs of the mint family might help prevent or treat Covid. Individual citizens could easily explore the hypothesis using ordinary kitchen materials. I offer a philosophical framework to account for the puzzling lack of public health messaging about this interesting idea.

This paper presents a new low-voltage versatile mixed-mode filter which uses a multi-ple-input/output differential difference transconductance amplifier (MIMO-DDTA). The multi-ple-input of the DDTA is realized using a multiple-input bulk-driven MOS transistor (MI-BD-MOST) technique to maintain a single differential pair, thereby achieving simple structure with minimal power consumption. In a single topology, the proposed filter can provide five standard filtering functions (low-pass, high-pass, band-pass, band-stop, and all-pass) in four modes: voltage (VM), current (CM), transadmittance (TAM), and transimpedance (TIM). This provides the full capability of a mixed mode filter (i.e., twenty filter functions). Moreover, the VM filter offers high-input and low-output impedances and the CM filter offers high-output impedance; therefore, no buffer circuit is needed. The natural frequency of all filtering functions can be electronically controlled by a setting current. The voltage supply is 0.5 V and for a 4 nA setting current, the power consumption of the filter was 281 nW. The filter is suitable for low-frequency biomedical and sensor applications that require extremely low supply voltages and nano-watt power consumption. For the VM low-pass filter, the dynamic range was 58.23 dB @ 1 % total harmonic distortion. The proposed filter was designed and simulated in the Cadence Virtuoso System Design Platform using the 0.18 µm TSMC CMOS technology.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

This work studies a novel low voltage (<60 V) hybrid system that supports engine boosting and downsizing in addition to start-stop, regenerative braking, and constrained torque assist/regeneration. The hybrid power split supercharger (PSS) shares a 9 kW motor between supercharging the engine or providing hybrid functionalities through a planetary gear set, a brake and a bypass valve. The PSS operation is limited to only one of the parallel hybrid or boosting modes at a time, necessitating a highly optimized decision making algorithm to select the device mode and power split ratio. In this work an adaptive equivalent consumption minimization strategy (A-ECMS) is developed for energy management of the PSS. The A-ECMS effectiveness is compared against a dynamic programming (DP) solution with full drive cycle preview through hardware-in-the-loop experiments on an engine dynamometer testbed. The experiments show that the PSS with A-ECMS reduces a vehicle fuel consumption by 18.4% over standard FTP75 cycle compared to a baseline turbocharged engine, while global optimal DP solution decreases the fuel consumption by 22.8% compared to baseline.

Artificial intelligence (AI) has emerged as a powerful tool for addressing the challenges posed by climate change and their impact on public health. By leveraging its capacity to analyze and predict climatic patterns, AI offers opportunities to enhance resource management and develop effective strategies for climate change mitigation. Moreover, AI can contribute to generating sustainable solutions that address the complex and interconnected nature of climate change. For example, AI can enable the optimization of energy consumption and facilitate the integration of renewable energy sources into existing systems. It can also support the development of climate models that provide timely and accurate predictions, enabling policymakers to implement proactive measures for disaster preparedness and response. Furthermore, AI-powered disease surveillance and mitigation techniques can improve public health outcomes by identifying patterns and trends in the spread of diseases in relation to climatic factors.However, the widespread adoption of AI-based solutions is not without challenges. Ethical concerns surrounding privacy and data ownership must be addressed, as the use of AI requires access to large datasets, raising potential privacy risks. Technical constraints, such as limited computational power and the need for sophisticated algorithms, also pose obstacles to the implementation of AI in climate change mitigation strategies. Furthermore, issues related to the accessibility and affordability of AI technologies must be resolved to ensure equitable distribution and maximize its potential impact on public health.To fully harness the power of AI in addressing climate change and improving public health outcomes, it is crucial to promote innovation, multidisciplinary collaboration, and open data science. Innovation can drive the development of new AI algorithms and technologies specifically tailored to address climate change challenges. Multidisciplinary approaches that bring together experts from diverse fields, including climate science, public health, and computer science, can foster a holistic understanding of complex systems and enable the design of comprehensive solutions. Finally, open data science practices, such as sharing data and algorithms, can facilitate collaboration and accelerate progress in mitigating climate change and its public health impacts.In conclusion, AI offers promising opportunities for effectively addressing climate change and its impact on public health. However, to fully realize its potential, it is essential to tackle ethical and privacy concerns, overcome technical constraints, and ensure accessibility and affordability. By promoting innovation, multidisciplinary collaboration, and open data science, we can unlock the transformative power of AI in mitigating climate change and improving public health outcomes.

Abstract: Field studies with large-stemmed plants Artemisia dubia (wormwood) have been carried out at Vėžaičiai Branch LAMMC since 2018. According to three years of experimental results, annual dry matter (DM) yield varied from 7.94 to 10.14 t ha-1. Growing conditions, nitrogen ap-plication level and harvesting time had significant impacts on Artemisia dubia productivity. This article presents the results of research on preparation and use of Artemisia dubia biomass for en-ergy conversion and evaluation of technological-technical and environmental parameters of these plants utilization for solid biofuel. For experiments were used 6 variants of Artemisia dubia samples, which were grown in 2021: plants were cut three times and two fertilization options were used: (1) no fertilization and (2) fertilization with 180 kg ha-1 of nitrogen fertilizer. These harvested plants were chopped, milled and were pressed into the pellets. The physi-cal-mechanical characteristics (mоisture content, density and strength) of Artemisia dubia pellets were investigated. During this study, it was found that the density in dry mass (DM) of pellets ranged from 1119.86 to 1192.44 kg m-3. The pellet moisture content ranged from 8.80 to 10.49%. After testing of pellet strength, it was found that the pellets which were made from plant bio-mass PK-1-1, were the most resistant to compression, they withstood 560.36 N of pressure. Dry fuel lower heating value (LHV) of pellets was sufficiently high and was very close to pine saw-dust pellets, it varied from 17.46±0.25 MJ kg-1 to 18.14±0.28 MJ kg-1. The ash content of burned pellets ranged from 3.62±0.02% to 6.47±0.09%. Emissions of harmful pollutants – CO2, CO, NOx and unburnt hydrocarbons (CxHy) did not exceed the maximum permissible levels. Summariz-ing the results of investigated properties, cоmbustion and emissiоns of Artemisia dubia pellets, it can be concluded that this biofuel can be used for production of pressed biofuel and it is charac-terized by sufficient high quality, efficient combustion and permissible emissions to the envi-ronment.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

This paper proposes an approach to estimate the parameters of an AC-DC boost power factor corrector converter which includes an EMI filter. To this end, once the topology is known, measurements at the input and output terminals of the converter are done to identify the values of the passive elements. The proposed methodology is based on the trust-region nonlinear least squares algorithm to identify the parameters of the converter. The steady-state and the transient signals of the converter at the input/output terminals are acquired non-intrusively without any internal modification of the circuitry. The accuracy of the parameter identification carried out is determined by comparing the estimated values with the actual values provided by the manufacturer, and by contrasting the measured signals with the ones obtained with a simulation model with the estimated values of the parameters. The results presented in this paper prove the accuracy of the proposed approach, which can be extended to other power converters and filters.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

This article presents a decentralized phase-shedding technique for multiphase converters. The usual central digital controller is replaced by identical local controllers forming a daisy-chain structure. Phase-shedding decisions are taken locally based on a local inductor current monitoring and threshold crossing management. This control strategy allows to implement as many phases as desired in a modular manner. In order to handle specific events such as load current inrush or a start-up sequence and to guarantee optimal transient responses, additional functions are included into each local controllers. The inter-cell communication protocol is described, along with necessary design considerations of threshold and timing values. Finally, functional simulations are carried out on a 5-leg 12V/1.2V 60W multiphase converter, which validate the proposed decentralized phase-shedding strategy for a microcontroller power supply implementation.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

The concepts of fractional calculus and the related techniques have been gaining momentum in circuit system fields, and an increasing body of evidence suggests that fractional-order characteristics are widely distributed in electronic components. In this paper, we consider the fractional characteristics of non-solid aluminum electrolytic capacitors and focus on the nonlinear dynamic characteristics of peak-current-mode controlled (PCMC) dc-dc boost converters with such components. In the work, we establish a piecewise smooth non-commensurate fractional-order model to describe the converter, in which the fractional-order equivalent impedance model of capacitors is adopted and the detailed control loop is considered. In order to analyze the converter, we use the fractional Adams-Bashforth-Moulton typed method (F-ABM) and stroboscopic map technique to obtain the time-domain solutions and the bifurcation diagram. The results of bifurcation diagrams indicate that, with the change of different parameters, the converter enters chaotic state through period doubling bifurcation. In order to provide empirical evidence for the nonlinear dynamic analysis, we consider both circuit-level simulation and experiments in the work, the results of which further confirm the results of theoretical analysis.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

This study considers an application of the first-order Grey Markov Model to foresee the values of Italian power generation in relation to the available energy sources. The model is used to fit data from the Italian energy system from 2000 to 2022. The integration of Markovian error introduces a random element to the model, which is able now to capture inherent uncertainties and misalignments between the Grey model predictions and the real data. This application provides valuable insights for strategic planning in the energy sector and future developments. The results show good accuracy of the predictions, which provides powerful information for the effective implementation of energy policies concerning the evolution of energy demand in the country. Despite advancements, Italy’s 2032 energy mix will still significantly rely on fossil fuels, emphasizing the need for sustained efforts beyond 2032 to enhance sustainability.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Data4HumanRights training materials have been developed as open-source and tailored to limited resource settings where community data collectors often live and work. An overview of how the training material was developed together with community data collectors in Nigeria and Kenya is provided. The paper gives insights into the fundamental principles (i.e., inclusiveness, adaptive, limited resources, gender- and incentive-sensitive) and the structure of the open-access training materials. This resulted in 28 modules designed to be delivered in a face-to-face format in less than one day by a local trainer. To maximize adaptivity, the training modules can be mixed and matched (e.g., as individual modules or a learning path of several modules around a specific training need). The individual modules cover a range of methods and tools that are useful to human rights work, for example, documenting evictions, performing rapid needs assessments after acute crises, community profiling, and monitoring community development indicators. The training materials contain instructions for the facilitator(s) of the training and all necessary training materials to conduct the training. To maximize inclusivity, the training covers basic to advanced topics. Most training modules address basic training topics that can be optimally followed with a mobile phone (to avoid using a computer and printing handouts). The training was developed and implemented with local community groups in Nigeria and Kenya. The material is free to use, adapt, and translate into different contexts and languages.

In the face of escalating climate concerns and the push for sustainable development, the global shift towards renewable and decentralized energy systems presents new challenges and opportunities. This study investigates integrating decentralized energy production, particularly photovoltaic (PV) systems, into national energy planning, aiming to optimize energy strategies that balance local production and consumption with national objectives. By analyzing the Swiss energy model, the research employs the EnergyScope and REHO models to assess the strategic implications of decentralized versus centralized energy systems. Results show that a decentralized approach can significantly reduce PV installation needs to 35 GW, about 23% of potential capacity, and decrease annual system costs by 10% to CHF 1230 per capita. This strategy emphasizes local consumption, minimizes grid reinforcement demands, and leverages economic advantages while addressing overproduction challenges through effective energy storage and grid management. Conclusions underline the strategic value of combining centralized and decentralized methods for resilient and sustainable energy planning. The study contributes to the discourse on energy policy and infrastructure planning, advocating for a hybrid model that accommodates both local conditions and broader energy objectives, urging further research into climate impacts and technology integration for a comprehensive energy future.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

This paper introduces a structured design for an effective power-sharing technique among converter-interfaced distributed generation (DG) units within a microgrid that operates without a synchronous generator. The proposed power-sharing technique leverages the battery energy storage system (BESS) to promptly respond to network changes. The real power output of each commercial distributed energy resources (CDER) unit is governed by a frequency-droop characteristic and a complementary frequency restoration strategy. Deloading techniques are employed by solar and wind power generators to enhance response during power supply or demand disturbances. To ensure microgrid stability, small-signal analysis is conducted for controller design, including the determination of stability margins. Initial tuning of the power-sharing technique parameters is achieved using the Ziegler-Nichols Method, followed by further optimization through a meta-heuristical algorithm to enhance the response time of energy sources. The proposed power-sharing technique's performance is evaluated on a benchmark medium voltage network using industry-standard commercial software. The test results demonstrate the precise and rapid power-sharing capabilities among DGs facilitated by the proposed technique, highlighting its effectiveness in dynamic microgrid environments.

This paper presents the design of a high frequency zero voltage switching (ZVS) full-bridge converter with a phase-shifted driving signal for photovoltaic applications. The resonant power converter can provide high-power capacity under high-frequency operation. The proposed power converter can also reduce the size of the transformer under the same power rating. The high-frequency transformer was developed by using the resonant and switching frequencies of the power converter to reduce the switching loss and to improve the system efficiency. Phase-shifted modulation was selected to drive the switches of a full-bridge power converter based on the switching loss minimization method. The desired output voltage was controlled using a closed-loop controller under a loop gain stability margin. The simulation results showed that the output voltage can be controlled to the desired constant when the input voltage changes from 30 VDC to 60 VDC. The desired output voltage of power converter is constant at 400 VDC. The power converter can transfer the DC supply to a 220 VAC household via grid-connected inverter. Therefore, the proposed study showed the effectiveness of the phase-shift ZVS full-bridge power converter with high-frequency transformer. This power converter can control the operation of the desired voltage system and has a small sizing of power converter system, low switching loss, and high system efficiency.

Abstract: Letter migrations between words in reading aloud (e.g., reading "cane love" as "lane love" or "lane cove") are known to result from a deficit in the visual-orthographic analysis and characterize attentional dyslexia. In spontaneous speech, individuals with impairment in the phonological output buffer may show migrations of phonemes between words. The purpose of this study was to examine whether migrations between words in reading aloud can also result from a deficit in the phonological output buffer, to explore the characteristics of migrations resulting from orthographic input and from phonological output deficits, and to examine methods to distinguish these two sources. Using tasks of reading aloud of 92-182 word pairs, we identified 18 adults and adolescents with developmental dyslexia who made between-word letter migrations in reading aloud, significantly more than age-matched controls (372 adults and 26 7th-graders). To distinguish between orthographic-input and phonological-output sources for these migrations, we administered a test assessing orthographic-input without spoken-output (written-semantic-decision on 140 migratable word pairs) and a test of repetition of 36 auditorily-presented migratable word pairs, assessing spoken output without orthographic-input (and word span tests). These tests indicated that the migrations of ten of the participants with dyslexia resulted from an orthographic-input deficit, and for the other eight participants, migrations resulted from a phonological-output deficit. We identified several differences between the two types of between-word errors: first, whereas the individuals with attentional dyslexia made omissions of a letter that appeared in the same position in the two words, the phonological output buffer group did not make such omissions. In addition, the groups differed in the origin of migration: orthographic input migrations involve letters that are orthographically adjacent, whereas phonological output migrations involve phonemes that have just been spoken or that are prepared together in the phonological buffer for production. This was manifested in that migrations from the line below and from two lines above occurred only in the orthographic input deficit group, and migrations occurred from a word vertically close to the target in the orthographic input group but from a word that has just been spoken (placed diagonally to the target) in the phonological output group. This study thus indicates that between-word migrations in reading-aloud can result not only from attentional dyslexia, but also from a phonological output buffer deficit, and offers ways to distinguish between the two.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

Green hydrogen is likely to play an important role in meeting the net zero targets of countries around the globe. Hence, producing green hydrogen cheaply and effectively is an important area of research. One potential option for green hydrogen production is to run electrolysers directly from offshore wind turbines, with no grid connection and hence no expensive cabling to shore. The removal of the grid presents an unusual integration challenge. The variable nature of wind turbines and farms results in a power output that can fluctuate more quickly than the electrolyser’s ability to respond without significantly stressing the electrolyser. Thus, the use of a battery, with the wind farm, becomes essential to even out some of the power variations that the electrolyser cannot deal with. In this work, a proof of concept of a wind farm control methodology designed to reduce variability in wind farm active power output is presented. Smoothing the power supplied by the wind farm to the battery reduces the size and number of battery charge cycles and helps to increase battery lifetime. Considering off-grid wind farms which exclusively power an electrolyser, this work quantifies the impact of the wind farm control method on battery lifetime for wind farms of 1, 4, 9 and 16 wind turbines. This is achieved using suitable wind farm, battery and electrolyser models. As an example, for the largest wind farm studied, consisting of 16 x 5 MW wind turbines, batteries with a lifetime of 15 years have approximately a 30 % reduction in required capacity (reduced from 14 MWh to 10 MWh) compared to operating without wind farm control. It is found that reducing the variability of the active power output of wind farms through the wind farm control methodology presented can have a significant impact on battery degradation and hence on battery lifetime. Hence, wind farm control can reduce the required battery capacity for a given lifetime or it can increase the lifetime of a given battery capacity. The work presented shows that wind farm control could play a critical role in reducing the levelised cost of green hydrogen produced from wind farms with no grid connection and paves the way for the design and testing of a full implementation of the wind farm control.

Mycobacterium tuberculosis was responsible for 1.3 million deaths worldwide in 2022. Bacillus Calmette-Guérin (BCG) is the only licensed vaccine against tuberculosis (TB); however, it has limited protective efficacy in adults. In this study, we constructed a recombinant vaccinia virus expressing Ag85B from M. tuberculosis using a novel attenuated vaccinia virus (KVAC103). We then analyzed the immunogenicity of prime-boost inoculation strategies using recombinant KVAC103 expressing Ag85B (rKVAC85B) compared to BCG. In both the rKVAC85B prime-boost and the BCG prime-rKVAC85B boost inoculation regimens, rKVAC85B induced the generation of specific IgG and the secretion of IFN-γ by immune cells. In vitro analysis of Mycobacterium growth inhibition revealed a comparable immune-mediated pattern of outcomes. Furthermore, bacterial loads in the lungs were significantly lower in mice inoculated with the BCG prime-rKVAC85B boost, than in the BCG-only group following a rechallenge infection with both H37Rv and HN878 strains of M. tuberculosis. These findings collectively suggest that KVAC103, incorporated into a viral vector, is a promising candidate for a novel TB vaccine platform that is effective against multiple TB strains, including H37Rv and HN878, and that rKVAC85B effectively stimulates immune responses against TB infection.

Various renewable energy sources such as wind power and photovoltaic (PV) have been increasingly integrated into the power system through power electronic converters in recent years. However, power electronic converter-driven stability issues under specific circumstances, for instance, modal resonances might deteriorate the dynamic performance of the power systems or even threaten the overall stability. In this paper, the integration impact of a hybrid renewable energy source (HRES) system on modal interaction and converter-driven stability is investigated in an IEEE 16-machine 68-bus power system. Firstly, an HRES system is introduced, which consists of full converter-based wind power generation (FCWG) and full converter-based photovoltaic generation (FCPV). The equivalent dynamic models of FCWG and FCPV are then established, followed by the linearized state-space modeling. On this basis, converter-driven stability analyses are performed to reveal the modal resonance mechanisms of the interconnected power systems and the modal interaction phenomenon. Additionally, time-domain simulations are conducted to verify effectiveness of dynamic models and support the converter-driven stability analysis results. To avoid detrimental modal resonances, an optimization strategy is further proposed by retuning the controller parameters of the HRES system. The overall results demonstrate the modal interaction effect between external AC power system and the HRES system and its various impacts on converter-driven stability.

Turbidity stands as a crucial indicator for assessing water quality, and while turbidity sensors exist their high cost prohibit their extensive use. In this paper, we introduce an innovative turbidity sensor, and it is the first low-cost turbidity sensor which is designed specifically for long-term stormwater in-field monitoring. Its low cost ($23.50 USD), enables the implementation of high spatial resolution monitoring schemes. The sensor design is available under open hardware and open-source licences, and the 3D-printed sensor housing is free to modify based on different monitoring purposes and ambient conditions. The sensor was tested both in the laboratory and in the field. The laboratory results show a strong linear relationship (R2 > 0.99) between the sensor readings and the commercial hand-held turbidimeter (Thermo Scientific AQ4500) results of the solution. In the field, the low-cost sensor measurements were statistically significantly correlated (p < 0.01) to a standard high-cost commercial turbidity sensor (GreenSpan TS-1000). Biofouling and drifting issues were also analysed after the sensors were deployed in the field for more than 6 months, showing both biofouling and drift occur during monitoring. Nonetheless, in terms of maintenance requirements, the low-cost sensor exhibited similar needs compared to the Green-Span sensor.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

A widely used material for the photovoltaic (PV) arrays is crystalline silicon. The PV conversion losses of a power plant as a yearly average, include: light reflection losses (3,1%), low radiation and shadowing losses (3,2%), DC board losses (1,2%), DC/AC conversion losses (4%), mismatching losses (5,7%), temperature losses (7,6%), it can be stated that the major fraction of losses is related to the temperature increase of the sili-con solar cells. In real operating conditions, solar cells and modules operate at different temperatures, either due to changes in ambient temperature (atmospheric conditions changing with the seasons) and cooling rate, depending on wind speed and insolation, rain, snow, etc., or due to changes in the amount of heat (electrical power lost on the internal resistance of the cell), emitted during their operation. The possibility of operation of these devices in ground applications in the temperature range from -20 to +70C should be taken into account. The given range, of course, does not apply to work in the tropics. The detailed studies of the temperature on the electrical parameters of crystalline silicon solar cells have been presented. The theoretical justification of the temperature influence mechanism on the exploitation parameters of the silicon solar cells was submitted. Photovoltaic cells and modules are of better quality, the lower the value of temperature coefficients, in particular, attention should be paid to the decrease in maximum power with increasing temperature.The experimental results were compared with the theoretical predictions and the results, obtained by other authors and producers.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

In modern inverter applications, multilevel converters are used thanks to their capability of reducing the passive fi lter volumes, improving the overall THD, sharing the power sources across the several converter cells, and providing a reconfi guration ability in case of failure. However, increasing the number of cells makes more complex the control of the converter. This article proposes a decentralized control technique based on the use of elementary modular controllers, associated with each converter cell and communicating with their close neighbors to obtain the balancing of the powers they supplied. Each modular controller can be dynamically removed or added to allow reconfi guration of the converter for functional safety purpose. This method is applied to a 240V/3A 5-cells Cascaded Full-Bridge Multilevel Converter. The response of the system to load transients and cell voltage disturbances demonstrates the robustness of the proposed decentralized control method. Thanks to the use of modular controllers, the number of levels of the converter can be extended to the order N without adding complexity to its control.