The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

To enhance pomegranate production on marginal gravelly lands, our study evaluated standardized planting techniques in an 8-year-old orchard. We employed trenching, wider pit excavation, pit digging, and auger digs with dimensions of 1 and 2 meters. Utilizing native soil from barren land, with or without spent wash, and mixing it with black soil up to 1 meter deep, we assessed growth parameters, leaf nutrients, and fruit yield. The trench and wider pit methods outperformed others, yielding greater above-ground biomass (>7.03 t tree-1), root biomass (2.5 t tree-1), and cross-sectional area (3.3 m² tree-1). Additionally, trench planting enhanced leaf phosphorus (0.28%) and potassium (1.8%) levels, fruit juice content (48.5%), total soluble solids (16.05°), and fruit yield (>9.3 t ha-1). The trench method also fostered longer roots at 90–150 cm radial distance and deeper roots at 40–60 cm depth. In summary, the trench and wider pit methods, combined with a soil mixture, are recommended for sustainable, high-quality fruit production in shallow gravelly terrains, thereby improving food security and the livelihoods of farmers in arid regions.

Ectopic expression of the MYB transcription factor of AmROSEA1 from Antirrhinum majus has been reported to change anthocyanin and other metabolites in several species. In this study, we found that overexpression of AmRosea1 significantly improved the tolerance of transgenic rice to drought and salinity stress. Transcriptome analysis revealed that a considerable amount of stress-related genes were affected by exogenous AmRosea1 during both drought and salinity stress treatments. These affected genes are involved in stress signal transduction, the hormone signal pathway, ion homeostasis and the enzymes that remove peroxides. This work suggests that the AmRosea1 gene is a potential candidate for genetic engineering of crops.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

The constant increase in current density in electrical wires leads to increasingly significant heat losses due to Joule effect. Therefore, reducing the electrical resistivity of copper wires becomes necessary. To achieve this goal, the development of a composite material incorporating a more conductive reinforcement, the graphene, is a promising way. The design of a copper/graphene composite using a powder metallurgy-based method is presented. This synthesis method allows for interface control through the growth of CuO(Cu) nanoparticles tightly bonded to the reinforcement. It also involves the dispersion of graphene through ultrasonic treatment and its alignment within the matrix using a uniaxial pressing densification method. The increase in the hardness (+12 HV) demonstrates the effective dispersion and separation of graphene layers. The impact on the electrical properties of dendritic copper (ρe = 2.30 µΩ.cm) remains limited, with a decrease in electrical resistance of approximately 1.4%. However, for copper with higher electrical resistivity, flake copper (at 2.71 µΩ.cm) and brass at (7.66 µΩ.cm), reductions of 2.7% and 10% have been achieved, respectively. With the improvement of graphene quality, there is more room to improve the electrical properties. This work paves the way for the development of composites with improved electrical resistivity.

This review aims to explore the intricate relationship between epigenetic mechanisms, stress, and affective disorders, focusing on how early life experiences and coping mechanisms contribute to susceptibility to mood disorders. Epigenetic factors play a crucial role in regulating gene expression without altering the DNA (deoxyribonucleic acid) sequence, and recent research has revealed associations between epigenetic changes and maladaptive responses to stress or psychiatric disorders. A scoping review of 33 studies employing the PRISMA-S (Preferred Reporting Items for Systematic Reviews and Meta-Analyses – Statement) guidelines investigates the role of stress-induced epigenetic mechanisms and coping strategies in affective disorders' occurrence, development, and progression. The analysis encompasses various stress factors, including childhood trauma, work-related stress, and dietary deficiencies, alongside epigenetic changes such as DNA methylation and altered gene expression. Findings indicate that specific stress-related genes frequently exhibit epigenetic changes associated with affective disorders. Moreover, the review examines coping mechanisms in patients with bipolar disorder and major depressive disorder, revealing mixed associations between coping strategies and symptom severity. While active coping is correlated with better outcomes, emotion-focused coping may exacerbate depressive or manic episodes. Overall, this review underscores the complex interplay between genetic predisposition, environmental stressors, coping mechanisms, and affective disorders. Understanding these interactions is essential for developing targeted interventions and personalized treatment strategies for individuals with mood disorders. However, further research is needed to elucidate specific genomic loci involved in affective disorders and the clinical implications of coping strategies in therapeutic settings.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

Pregnancy is a complex biological process which is associated with significant metabolic and hemodynamic changes of the maternal body which allow a normal fetal growth. The inability to adapt to these changes can affect the cardiovascular health. During pregnancy, women may experience mood swings, anxiety and emotional ambivalence. These symptoms can lead to stress and have a negative impact on the mental well-being of expectant mothers. It is crucial to know the aspects that can influence the development of cardiovascular problems among pregnant women in order to manage these cases properly. The current narrative review explores and summarizes the evidence regarding the impact of stress and anxiety on cardiovascular health in pregnant women. Understanding the physiological adaptations that the body undergoes throughout pregnancy is crucial for educating and supporting individuals as well as healthcare professionals. This enables them to recognize any risk factors or pathological conditions that may exacerbate pregnant women's health. In order to reduce maternal morbidity and mortality from cardiovascular disease, a psychological and cardiovascular risk factor screening that is done either before or during pregnancy may be able to identify situations that call for particular medical and/or psychological therapies.

Millions of people worldwide are affected by diabetes, a chronic disease that continuously grows due to abnormal glucose concentration levels present in the blood. Monitoring blood glucose concentrations is therefore an essential diabetes indicator to aid in the management of the disease. Enzymatic electrochemical glucose sensors presently account for the bulk of glucose sensors in the market. However, their disadvantages are that they are expensive and are dependent on environmental conditions, hence affecting their performance and sensitivity. To meet the increasing demand, non-enzymatic glucose sensors based on chemically modified electrodes for the direct electrocatalytic oxidation of glucose are a good alternative to the costly enzymatic-based sensors currently on the market, and the research thereof continues to grow. Nanotechnology-based biosensors have been explored for their electronic and mechanical properties, resulting in enhanced biological signalling through the direct oxidation of glucose. Copper oxide and copper sulfide exhibit attractive attributes for sensor application, due to their non-toxic nature, abundance, and their unique properties. Thus, in this review, copper oxide and copper sulfide-based materials, are evaluated based on their chemical structure, morphology, and fast electron mobility as suitable electrode materials for non-enzymatic glucose sensors. The review highlights the present challenges of non-enzymatic glucose sensors that have limited their deployment into the market.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

In the present study, fish were exposed to sub-lethal doses of CuONPs (68.92 ± 3.49 nm) (10, 20, and 50 mg/L) for a long exposure period (25 days). Compared to the control group (0.0 mg/L CuONPs), a significant dose-dependent elevation in blood urea and creatinine values, serum alanine transaminase, aspartate transaminase, and alkaline phosphatase enzyme activities were evident in CuONPs-exposed groups (P &lt; 0.05). Fish exposure to 50 mg/L CuONPs significantly upregulated the transcription of pro-inflammatory cytokines (tumor necrosis factor-alpha, interleukin-1beta, interleukin 12, and interleukin 8), heat shock protein 70, apoptosis-related gene (caspase 3), and oxidative stress-related (superoxide dismutase, catalase, and glutathione peroxidase) genes in liver and gills of the exposed fish in comparison with those in the control group (P &lt; 0.05). Moreover, varying histopathological injuries were noticed in the hepatopancreatic tissues, posterior kidneys, and gills of fish groups correlated to the examined exposure dose of CuONPs. In summary, our results provide new insights and helpful information for better understanding the mechanisms of CuONPs toxicity in Nile tilapia at hematological, molecular levels, and tissue levels.

According to previous studies the median raphe region (MRR) is known to contribute significantly to social behavior. Beside serotonin, there are reports of a small population of dopaminergic neu-rons in this region. Dopamine is linked to reward and locomotion, but very little has been known about its role in the MRR. To address that, we first confirmed the presence of dopaminergic cells in the MRR of mice (immunohistochemistry, RT-PCR) and humans (RT-PCR). Next, we used chemogenetic technology in mice containing Cre enzyme under the promoter of the dopamine transporter (DAT). With the help of an adeno-associated virus, artificial receptors were expressed in the dopaminergic cells of the MRR (DAT-MRR). Four weeks later, extensive behavioral charac-terization started 30 minutes after the injection of the artificial ligand (Clozapine-N-Oxide). Stimu-lation of DAT-MRR decreased social interest without influencing aggression and with an increase in social discrimination. Additionally, inhibition of the same cells increased the friendly social be-havior during social interaction test. No behavioral changes were detected in anxiety, memory and locomotion. All in all, dopaminergic cells were present both in the mice and human MRR, and manipulation of dopaminergic neurons of the MRR elicited a specific social response.

Direct-to-blister copper flash smelting slag contains up to 14% of copper and 2-4% of lead. Considering this fact, this material is subjected to the high-temperature reduction process. After this, converting process is performed on the Cu-Pb-Fe alloy being the product of decopperization process in electric furnace. An alternative to the presently used processing of flash smelting slag would be its hydrometallurgical treatment and selective recovery of Pb and Cu. This paper presents the results of laboratory tests on flash smelting slag leaching with citric acid solutions. The experiments performed allowed to determine the process parameters at which the Pb concentration in the post-leaching sediment reached the value of 0.41-0.6% while the Pb content in flash smelting slag was 3.05%. Analogous values for copper were 11.5-11.8% (after leaching) and 12.44% (before). Material after leaching in citric acid solutions can be processed, in the second step, using sulfuric acid solutions, and it could lead to the recovery of almost all copper contained in it.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

Copper (Cu) is an essential micronutrient for the correct development of eukaryotic organisms. This metal plays a key role in many cellular and physiological activities, including enzymatic activity, oxygen transport, and cell signaling. Although the redox activity of Cu is crucial for enzymatic reactions, this property also makes it potentially toxic when found at high levels. Due to this dual action of Cu, highly regulated mechanisms are necessary to prevent both the deficiency and the accumulation of this metal since its dyshomeostasis may favor the development of multiple diseases, such as Menkes’ and Wilson’s diseases, neurodegenerative diseases, diabetes mellitus, and cancer. As the relationship between Cu and cancer has been the most studied, we analyze how this metal can affect three fundamental processes for tumor progression: cell proliferation, angiogenesis, and metastasis. Gynecological diseases are characterized by high prevalence, morbidity, and mortality, depending on the case, and mainly include benign and malignant tumors. The cellular processes that promote their progression are affected by Cu, and the mechanisms that occur may be similar. We analyze the crosstalk between Cu deregulation and gynecological diseases, focusing on therapeutic strategies derived from this metal.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

Copper, which can potentially be a highly toxic agent, is an essential nutrient due to its role as a co-factor for cuproenzymes and participation in signaling pathways. In mammals, the liver is a central organ that controls copper turnover throughout the body: copper absorption, distribution, and excretion. In ontogenesis, there are two types of copper metabolism: embryonic and adult, which maintain the balance of copper in each of these periods, respectively. In the liver cells, these types are characterized by specific expression patterns and activity levels of the genes encoding ceruloplasmin, which is the main extracellular ferroxidase and copper transporter and proteins mediating ceruloplasmin metalation. In newborns, the molecular-genetic mechanisms responsible for copper homeostasis and the ontogenetic switch from embryonic to adult copper metabolism are highly adapted to milk ceruloplasmin as a dietary source of copper. In the mammary gland cells, the level of ceruloplasmin gene expression and the alternative splicing of its pre-mRNA govern the amount of ceruloplasmin in milk, and thus, the amount of copper absorbed by the newborn is controlled. In the newborns, absorption, distribution, and accumulation copper are adapted to milk ceruloplasmin. In the newborns, which are not breast-fed at the early stages of postnatal development, the control for alimentary copper balance is absent. We tried to focus on the neonatal consequences of a violation of the balance of copper in the mother / newborn system. Although there is still much to be learned, the time to pay attention to this problem came because the neonatal misbalance of copper may provoke the development of copper related disorders for future life.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

This manuscript employs a surface stress-driven nonlocal model to explore the combined effects of long-range interaction and surface energy on higher vibration modes of functionally graded nanobeams. The nanobeam theory, based on Bernoulli-Euler kinematics, incorporates surface effects such as surface elasticity, surface residual stresses, surface density, and rotary inertia. Hamilton's principle is applied to derive the governing equation with size-dependent considerations. The main outcomes of a parametric investigation, considering four different kinematic boundary conditions (Cantilever, Simply-Supported, Clamped-Pinned, and Doubly-Clamped) while varying the nonlocal parameter and material gradient index, are presented and discussed. Additionally, the normalized natural frequencies for the second, third, fourth and fifth modes of vibrations are provided and analyzed for each case under study. The results underscore the model's effectiveness in capturing surface energy effects on the overall dynamic behavior of functionally graded Bernoulli-Euler nanobeams, offering a cost-effective approach for designing and optimizing nano-scaled structures.

Supplementation with 200% of the recommended daily dietary quantity of copper modified vascular contraction and relaxation through increased reactive oxygen species (ROS) and prostaglandin formation, which modified the antioxidant status of middle–aged rats. In this study, young (1 month old) male Wistar rats (n/group = 10) received a diet supplemented with 6.45 mg copper/kg (100%—Group A) for 8 weeks. The experimental group received 12.9 mg copper/kg of diet (200%—Group B). Experimental supplementation with 200% copper increased the copper concentration in the blood, liver, and kidneys; increased the ROS concentration in the aortic rings; and enhanced the sensitivity of the aortic rings to acetylcholine. We observed increased participation of nitric oxide (NO) derived from inducible NO synthase (iNOS) in vascular contraction and a decreased net effect of vasodilator prostanoids derived from cyclooxygenase–2 (COX–2) in vascular relaxation. Supplementation with 200% copper was less significant than expected after previous studies conducted with middle–aged rats.

Abstract: Brassinosteroids (BR) are essential plant hormones that play a crucial role in regulating plant growth and development, as well as their resistance to abiotic and biotic stresses, including pathogen infections. In the context of plant im-munity, BR influence various processes such as the expression of genes related to pathogen defense, the production of antimicrobial compounds, and the re-inforcement of the plant cell structure. The aim of work is understand the role of BR in plant defense against abiotic and biotic stresses. BR are involved in the regulation of metabolic processes, water economy, and photosynthesis, contributing to increased plant resistance to abiotic stresses. The study discusses various mechanisms of BR action on plant immunity, including the regulation of gene expression related to defense, activation of the plant defense system, in-teraction with other plant hormones, regulation of water and salt balance, and influence on photosynthetic processes. In the context of plant immunity, BR influence various processes, including the expression of genes related to pathogen defense, the production of antimicrobial compounds, and the reinforcement of the plant cell structure. Additionally, BR are involved in the regulation of metabolic processes, water economy, and photosynthesis, con-tributing to increased plant resistance to abiotic and biotic stresses. The paper emphasizes the importance of further research on the role and mechanisms of action of BR in plant immunity, which may contribute to the development of more effective strategies for the use of BR in agriculture, horticulture, and plant protection.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

The biological aging, characterized by changing in metabolism and physicochemical properties of cells, has an impact on public health. Environment and lifestyle including factors like diet and physical activity seems to play a key role in healthy ageing. Several studies have shown that regular physical activity can enhance antioxidant defence mechanisms, including the activity of enzymes such as superoxide dismutase (SOD), catalase, and glutathione peroxidase. However, intense or prolonged exercise can also lead to an increase in ROS production temporarily, re-sulting in oxidative stress. This phenomenon is referred as "exercise-induced oxidative stress". The relationship between physical activity and oxidative stress in aging is complex and depends on various factors such as the type, intensity, duration, and frequency of exercise, as well as in-dividual differences in antioxidant capacity and adaptation to exercise. In this review, we ana-lyzed what is reported from several authors regarding the role of physical activity on oxidative stress in aging process as well as the role of hormesis and physical exercise as tools for preven-tion and treatment of sarcopenia, an aging related disease. Finally we reported what has recently been studied in relation to the effect of physical activity and sport on aging in women

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

There is much interest in effective copper chelators to correct copper dyshomeostasis in neurodegenerative and oncological diseases. In this study, a recombinant fusion protein for expression in E. coli cells was constructed from glutathione-S-transferase (GST) and the N-terminal domain (ectodomain) of human high affinity copper transporter CTR1 (hNdCTR1), which has three metal-bound motifs. Several biological properties of the GST-hNdCTR1 fusion protein were assessed. It was demonstrated that in cells, the protein was prone to oligomerization, formed inclusion bodies and displayed no toxicity. Treatment of E. coli cells with copper and silver ions reduced cell viability in a dose- and time-dependent manner. Cells expressing GST-hNdCTR1 protein demonstrated resistance to the metal treatments. These cells accumulated silver ions and formed nanoparticles that contained AgCl and Ag0. In this bacterial population, filamentous bacteria with length about 10 μm were often observed. The possibility for the fusion protein carrying extracellular metal binding motifs to integrate into the cell’s copper metabolism and its chelating properties are discussed.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

One method of creating a brass coating is through electrodeposition, which is most often completed in cyanide galvanic baths. Because of the toxicity of cyanides, many are working on the development of cyanide-free baths, which are promising but not satisfactory to replace the classic methods. The purpose of the study was to explore a new generation of non-aqueous cyanide-free baths based on 1-ethyl-3-methylimidazolium acetate ionic liquids. The study involved the formation of copper, zinc, and brass coatings. The influence of the bath composition, cathodic current density, and temperature was determined. The obtained coatings were characterized by their morphology, chemical composition, roughness, and corrosion resistance. It was found that the structure of the obtained coatings is strongly dependent on the process parameters. The three main structures observed were fine-grained, porous, and olive-like. To the best knowledge of the authors, it is the first time the olive-like structure was observed in the case of an electrodeposited coating. The Cu-Zn coatings consisted of 19–96 at.% copper and exhibited relatively strong corrosion resistance. High improvement of corrosion properties was found in the case of copper and brass coatings with an olive-like structure.

There is little doubt that the efficacy of MnDPDP and its therapeutic improved counterpart Ca4Mn(DPDP)5 mainly depends on their MnSOD-mimetic activity when it comes to their potential use as rescue medicines, during e.g., acute myocardial infarction. However, pharmacokinetic considerations suggest that the efficacy of MnDPDP on Pt2+-associated neurotoxicity depends on another action of this drug. Electron Paramagnetic Resonance (EPR) studies have demonstrated that Pt2+ outcompetes Mn2+ and endogenous Zn2+ from binding to fodipir (DPDP), and hence suggest that the previously reported CIPN protective efficacy of MnDPDP is a result of chelation and elimination of Pt2+ by DPDP, which in turn suggests that Mn2+ is unnecessary for efficacy when it comes to oxaliplatin-associated CIPN.

Abstract: Kiwifruit, a perennial horticultural crop known for its nutritional value, faces significant challenges due to biotic and abiotic stresses, affecting its yield and quality. Leucine-rich repeat receptor-like proteins (LRR-RLPs), a major group of receptor-like proteins in plants, have diverse functions in plant physiology, including growth, development, signal transduction, and stress responses. Despite their importance, the specific roles of kiwifruit LRR-RLPs in response to biotic and abiotic stresses remain poorly understood. In this study, we investigated the expression patterns of kiwifruit LRR-RLPs under various stress conditions, including pathogen stress, heat stress, waterlogging stress, and copper stress. Through genome and transcriptome analyses, we identified a total of 101, 164, and 105 LRR-RLPs in Actinidia Chinensis 'Hongyang', Actinidia eriantha 'Huate', and Actinidia chinensis 'Red5' kiwifruit, respectively, classified into 9 subgroups based on phylogenetic relationships. Synteny analysis revealed that the expansion of kiwifruit LRR-RLPs was primarily attributed to segmental duplication events. Using RNA-seq data from pathogen-infected kiwifruits, we identified specific LRR-RLP genes potentially involved in different stages of pathogen infection. Additionally, we observed the potential involvement of kiwifruit LRR-RLPs in abiotic stress responses, with upstream transcription factors possibly regulating their expression. Furthermore, protein interaction network analysis unveiled the participation of kiwifruit LRR-RLP genes in the regulatory network of abiotic stress responses. These findings highlight the crucial roles of LRR-RLPs in mediating both biotic and abiotic stress responses in kiwifruit, offering valuable insights for the breeding of stress-resistant kiwifruit varieties.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

Phytopathogenic fungi are living organisms that cause plant diseases and great damage to agri-cultural products. Despite the wide range of commercial fungicide products in use, there is a clear need for new and environmentally friendly fungicides. Here we propose a new ecological fun-gicide, copper alginate microspheres prepared by ionic gelation. The microspheres were charac-terized (morphology and topography, encapsulation efficiency, load capacity, swelling behavior, rheology, kinetics and mechanism of copper ions release) and their in vitro antifungal potential against selected genera of phytopathogenic fungi was evaluated. Novel copper alginate micro-spheres inhibited spore germination of Botrytis cinerea and mycelial growth of Cercospora beticola and Phytophthora ramorum. They offer effective disease control while minimizing environmental impact and promoting sustainable agriculture practices.

The accumulation of microorganisms, plants, algae, or small animals on wet surfaces that have a mechanical function causes biofouling, which can result in structural or other functional deficiencies. The maritime shipping industry must constantly manage biofouling to optimize operational performance, which is a common and long-lasting problem. It can occur in any metal structure in contact or submerged in ocean water, which represents additional costs in terms of repairs and maintenance. This study is focused on the production of antifouling coatings, made with nanoparticles of copper selenide (CuSe) modified with gum arabic, within a water-base acrylic polymeric matrix. During the curing of the acrylic resin, the CuSe NPs remain embedded in the resin but this does not prevent the release of ions. The coatings presented to release copper and selenium ions for up to 80 days, selenium was the element that was released the most. The adhesion of film coatings to metallic substrates showed good adhesion, scale 5B (ASTM D3359 standard). Antimicrobial activity tests show that the coatings have an inhibitory effect on Escherichia coli and Candida albicans. The effect being more noticeable when the coating is detached from the substrate and placed on a growing medium, than compared to the coating on a substrate. Scanning electron microscopy (SEM) observations show that nanostructured CuSe coatings are made up of rod-shaped and spherical particles whose range ranges from 12 to 25 nm. The Energy Dispersive X-ray spectroscopy (EDS) studies showed that the ratio of selenium nanoparticles is greater than that of copper and that their distribution is homogeneous

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Surface Plasmon Resonance (SPR) is an attracting property of certain transition metals when they are synthesized in nano-range giving rise to promising optical applications. However, most SPR and associated applications are limited to the noble metal nanoparticles, which limits their potential due to high production cost. We report surface plasmon resonance in copper-copper oxide core-shell quantum dots synthesized via chemical route studied by using UV-Visible spectrophotometry. Tuning of the plasmonic resonance with respect to the particle diameter is achieved by an inexpensive all chemical route. Photoluminescence measurements also support the data. This size reduction leads to remarkable changes in its optical response as compared to the bulk metal. The results point towards applications of these materials in tunable SPR based biosensors.

Background/Objectives: Vitamin B12 deficiency can cause variable symptoms, which may be irreversible if not diagnosed and treated in a timely manner. We aimed to develop a widely accepted expert consensus to guide the practice of diagnosing and treating B12 deficiency. Methods: We conducted a scoping review of the literature published in PubMed since January 2003. Data were used to design a two-round Delphi survey to study the level of consensus among 42 experts. Results: The panelists agreed on the need for educational and organizational changes in the current medical practices for diagnosing and treating B12 deficiency. Recognition of clinical symptoms should receive the highest priority in establishing the diagnosis. There is agreement that the serum B12 concentration is useful as a screening marker, whereas methylmalonic acid or homocysteine can support the diagnosis. Patient lifestyle, disease history and medications can provide clues to the cause of B12 deficiency. Regardless of the cause of the deficiency, initial treatment with parenteral B12 was regarded as the first choice for patients with acute and severe manifestations of B12 deficiency. The use of high-dose oral B12 at different frequencies may be considered for long-term treatment. Prophylactic B12 supplementation should be considered for specific high-risk groups. Conclusions: There is a consensus that clinical symptoms need to receive more attention in establishing a diagnosis. B12 laboratory markers can support the diagnosis. The severity of clinical symptoms, the causes of B12 deficiency and the treatment goals govern decisions regarding the route and dose of B12 therapy.

Background: The workplace burnout syndrome is often associated with particular aspects of certain job positions, especially those which entail working with people with special needs. The burnout syndrome in healthcare jobs is a serious problem which has grown into an epidemic among healthcare workers and associates. Objectives: The aim of this research is to assess the presence of stress and burnout syndrome at work with healthcare workers, expert workers, professional associates and associates in social service institutions in Belgrade. Material and Methods: This research has been conducted in the form of a cross-sectional study of a representative sample in social institutions in Belgrade. It has been conducted from March to the end of June of 2023. The sample of the study had 491 participants. The questionnaires used were a structured instrument with social-demographic and social-economic characteristics, workplace characteristics, life style characteristics, and the following questionnaires: DASS-21, Copenhagen, Brief Resilience Scale, and Brief Resilient Coping Scale. Results: The end results indicate the following to be significant risk factors for the occurrence of workplace burnout syndrome: overtime (OR=2.62; CI=1.50-4.56), BRS average score (OR=0.28; CI=0.17-0.44), DASS21 D heightened depression (OR=2.09; CI=1.1-4.04), DASS21 A heightened anxiety (OR=2.38; CI=1.34-4.21), DASS21 S heightened stress (OR=2.08; CI=1.11-3.89). The only protective risk factor which stood out was the self-assessment of health levels (OR=0.60; CI=0.42-0.85). Conclusion: Overtime is a significant predictor of workplace burnout. Apart from it, other significant predictors of workplace burnout were heightened depression, anxiety, and stress levels.

Probiotics are microorganisms infused in products for health benefits including acceleration of nutrient digestion, however, it is also important to ensure the safety prior to incorporation. Here, we present evidence of the ability of two probiotic isolates,Lacticaseibacillus paracasei BCRC-16100 and Lacticaseibacillus paracasei ZFM54, in the (1) enhancement of carbohydrate digestion, (2) tolerance to stress, and (3) antibiotic resistance. Approaches include whole genome sequence (WGS) analysis and bioactivity assays. WGS revealed genes suggesting the ability of the two isolates to promote carbohydrate digestion, tolerance to stress and antibiotic resistance. Carbohydrate digestive ability was confirmed through a biochemical assay where the two isolates cause glucose release from starch. The two isolates also showed versatility in a range of temperature and alcohol concentration. For antibiotic resistance particularly on vancomycin, there are three mechanisms namely transporter control, transcriptional regulation, and efflux pump. Furthermore, promoter and transposable element analysis showed that some of the active antibiotic resistant (AbR) genes can be laterally transferred. Altogether, we show the potential of two probiotic isolates to be incorporated in products for improved carbohydrate digestion and the need to address the removal of active and mobile antibiotic resistance genes that may compromise safety.

Information taken from David A. Scott’s book “Copper and Bronze in Art” was crucial for research on copper corrosion products in Stuttgart. Examples discussed are the nature and variability of ‘Black Spots’ (aka ‘Brown Fuzzies’); cupric hydroxide by cleaning, patination, and pigment synthesis; the wondrous phenomenon of curly malachite; chalconatronite formed by contact to soda glass; the formation of copper formates by glass-induced metal corrosion; and synthesis and X-ray diffraction of basic copper acetates (‘verdigris’).

Hybrid metal-organic compounds as relatively new and prosperous magnetoelectric multiferroics provide opportunities to improve the polarization, magnetization and magneto-electric coupling at the same time, which usually have some limitations in the common type-I and type-II multiferroics. In this work we investigate the crystal of guanidinium copper(II) formate [C(NH2)3]Cu(HCOO)3 and give novel insights concerning the structure, magnetic, electric and magneto-electric behaviour of this interesting material. Detailed analysis of crystal structure at 100 K is given. Magnetization points to the copper(II)-formate spin-chain phase that becomes ordered below 4.6 K into the canted antiferromagnetic (AFM) state, as a result of super-exchange interaction over different formate bridges. The performed ab-initio colinear density functional theory (DFT) calculation confirm the AFM-like ground state as a first approximation and explain the coupling of spin-chains into the AFM ordered lattice. In versatile measurements of magnetization of a crystal, including transverse component besides the longitudinal one, very large anisotropy is found that might originate from canting of the coordination octahedra around copper(II) in cooperation with the canted AFM order. With cooling down in zero fields the generation of spontaneous polarization is observed step-wise below 270 K and 210 K and the effect of magnetic field on its value is observed also in the paramagnetic phase. Measured polarization is somewhat smaller than the DFT value in the c-direction, possibly due to twin domains present in the crystal. The considerable magneto-electric coupling below the magnetic transition temperature is measured with different orientations of the crystal in magnetic field, giving altogether the new light onto the magneto-electric effect in this material.

Understanding potential uptake and biodistribution of engineered nanoparticles in soil-grown plants is imperative for toxicity and risk assessment considering the oral exposure of edibles by humans. Herein, we assessed potential influence of particle size (25, 50, and 250 nm) and concentration (0, 50, 100, 200, and 500 mg/kg-soil) of Copper oxide nanoparticles (CuONPs) on: (1) the root system architecture, and the physicochemical attributes of soil at the soil-root interface, (2) leading to Cu transport and accumulation in root, stem, leaf and seed in soybean (Glycine max cv Kowsar) grown for entire lifecycle of 120 days, and compared with soluble Cu²⁺ ions and water-only controls, and (3) performed a comparative assessment of total seed Cu levels in soybean with other valuable food sources for Cu intake and discussed its human health implications. Our findings showed particle size- and concentration-dependent influence of CuONPs on Cu uptake and tissue distribution in root, stem, leaf and seed in soybean. Alterations in root architecture (root dry weight, root length, root volume, and root area) were dependent on the Cu compound type, Cu concentrations, and their interactions (p<0.05), except for root density. Concentration-response relationships for all three sized CuONPs, and Cu²⁺ ions, were linear. CuONPs and Cu²⁺ ions had inhibitory effects on root growth and development. Overall, soybean responses to smallest size CuONPs-25 nm were higher for all parameters investigated compared to two larger sized CuONPs (50 nm, 250 nm) or Cu²⁺ ions. Cu uptake/bioaccumulation differed among soybean tissues in the order: root > leaf > stem > seed. Despite reduced root architecture and seed yield, our smallest size CuONPs-25 nm led to increased total seed Cu uptake compared to the larger sized CuONPs and Cu²⁺ ions tested. Our findings also suggest that soil amendment by CuONPs, more so by the smallest size CuONPs-25 nm, could significantly improve nutritional Cu value in soybean seed as reflected by % Daily Values (DV), and are rated “Good” to “Very Good” according to the “World’s Healthiest Foods” rating. However, until the potential toxicity and risk from consumption of soybean seed is characterized in humans, caution should be exercised when the Cu fortified seeds are used for daily human consumption when addressing Cu deficiency and associated illnesses, globally.

This general review assesses the impact of physical exercise on oxidative and nitrosative stress and the counteractive role of antioxidants, drawing from a systematic literature search up to March 2024 in databases like PubMed and Web of Science. The review highlights studies on the effect of exercise on the production of reactive oxygen species (ROS) and reactive nitrogen species (RNS) and antioxidant responses in both human and animal models based on rigorous inclusion and exclusion criteria. Due to the variety of exercise types and participants' characteristics, a narrative synthesis approach was adopted. The findings indicate that moderate exercise boosts antioxidant defenses, known as hormesis, whereas excessive physical activity may increase oxidative and nitrosative damage. The review also explores the complex effects of antioxidant supplementation, revealing that while natural dietary antioxidants support health, high-dose supplements could potentially hinder positive adaptations to exercise. Recommendations for athletes and the general active population highlight the importance of balancing exercise and dietary intake to optimize health benefits. The review concludes with a call for more detailed research on tailored exercise and nutrition plans to dissect these intricate relationships further.

Extensive green roofs provide for many ecosystem services in urban environments. The efficacy of these services is influenced by the substrate characteristics and vegetational composition. Despite their key role in plant performance and productivity, or their contribution to nitrogen fixation or carbon sequestration, green roof microbial communities have received little attention so far. Here, we investigated whether microbial communities in extensive green roof substrates contain a core community, as well as whether they are affected by green roof plant diversity. Eleven green roofs, planted either with a mixture of grasses, wildflowers and succulents (Sedum spp.), or solely species of Sedum, were seasonally sampled to investigate prokaryotic and fungal communities via metabarcoding. Although Sedum-herbs-grasses roofs contained more plant species, we observed no discriminant microbial communities between both roof types, likely due to sharing the same substrate textures and the vegetational layers that became more similar throughout time. Examining key microbial taxa revealed that most taxa are also dominant phylotypes in soils across different biomes. Many bacterial core taxa are capable of nitrogen fixation and most fungal key taxa are stress-tolerant saprotrophs, endophytes, or both. Microbial community composition further revealed high similarities with aerial samples taken in urban environments. Considering the extreme edaphic conditions that periodically arise in green roof substrates, further investigation is warranted to determine the extent to which the dynamic and intriguing microbial communities are influenced by the aeromicrobiome.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Plant-microbe interactions play a crucial role in shaping plant health and survival. In recent years, the role of extracellular vesicles (EVs) in mediating intercellular communication between plants and microbes has emerged as an intriguing area of research. EVs, serve as important carriers of bioactive molecules and genetic information, facilitating communication between cells and even between different organisms. Pathogenic bacteria leverage extracellular vesicles (EVs) to amplify their virulence, exploiting their cargo rich in toxins and virulence factors. Conversely, beneficial microbes initiate EV secretion to stimulate plant immune responses and nurture symbiotic relationships. The transfer of EV-packed small RNAs (sRNAs) has been demonstrated to facilitate the modulation of immune responses. Furthermore, harnessing the potential of EVs holds promise for the development of innovative diagnostic tools and sustainable crop protection strategies. This review highlights the biogenesis and functions of EVs in bacteria, and their importance in plant defense and paves the way for future research in this exciting field.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

Predicting copper price is essential for making decisions that can affect companies and governments dependent on the copper mining industry. Copper prices follow a time series that is non-linear, non-stationary, and which have periods that change as a result of potential growth, cyclical fluctuation and errors. Sometimes the trend and cyclical components together are referred to as a trend-cycle. In order to make predictions, it is necessary to consider the different characteristics of trend-cycle. In this paper, we study a copper price prediction method using Support Vector Regression. This work explores the potential of the Support Vector Regression with external recurrences to make predictions at 5, 10, 15, 20 and 30 days into the future in the copper closing price at the London Metal Exchanges. The best model for each forecast interval is performed using a grid search and balanced cross-validation. In experiments on real data-sets, our results obtained indicate that the parameters (C, ε, γ) of the model Support Vector Regression do not differ between the different prediction intervals. Additionally, the amount of preceding values used to make the estimates does not vary according to the predicted interval. Results show that the support vector regression model has a lower prediction error and is more robust. Our results show that the presented model is able to predict copper price volatilities near reality, being the RMSE equal or less than the 2.2% for prediction periods of 5 and 10 days.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Classical antibacterial drugs were designed to target specific bacterial properties distinct from host human cells to maximize potency and selectivity. These designs were quite effective as they could be easily derivatized to bear next generation drugs. However, the rapid mutation of bacteria and their associated acquired drug resistance have led to the rise of highly pathogenic superbug bacterial strains for which treatment with first line drugs is no match. More than ever, there is a dire need for antibacterial drug design that goes beyond conventional standards. Taking inspiration by the body’s innate immune response to employ its own supply of labile copper ions in a toxic attack against pathogenic bacteria, which have a very low Cu tolerance, this review article examines the feasibility of Cu-centric strategies for antibacterial preventative and therapeutic applications. Promising results are shown for the use of Cu-containing materials in the hospital setting to minimize patient bacterial infections. Studies directed at disrupting bacterial Cu regulatory pathways elucidate new drug targets that can enable toxic increase of Cu levels and perturb bacterial dependence on iron. Likewise, Cu intracellular chelation/prochelation strategies effectively induce bacterial Cu toxicity. Cu-based small molecules and nanoparticles demonstrate the importance of the Cu ions in their mechanism and display potential synergism with classical drugs.

The copper deposition on the platinum and palladium nanoelectrode has been studied using cyclic voltammetry. The use of nanoelectrode platinum and palladium are defined in the study of heavy metals. The noble nanoelectrode of metal has a typical silicone processing structure. In comparison to the nanoelectrodes, the geometry of the electrode series is complex and balanced. Nanoelectrodes of platinum are found effective in detecting heavy metal. There was regular analysis of the use of the sensors. The identification constraints down to the ng /L level was accomplished by refined electrode geometry and the stripping procedures. The process was used for the study of water sample determination. Another heavy metal ion attack voltammetric reaction was studied. The SEM picture clearly observed and characterized the nanoparticle electrode by X-ray diffraction and cyclic voltammetry.

Hypertensive diseases of pregnancy (HDP) represent a global clinical challenge, affecting 5-10% of women and leading to complications for both maternal well-being and fetal development. At the heart of these complications is endothelial dysfunction, with oxidative stress emerging as a pivotal causative factor. The reduction in nitric oxide (NO) bioavailability is a vital indicator of this dysfunction, culminating in blood pressure dysregulation. In the therapeutic context, although antihypertensive medications are commonly used, they come with inherent concerns related to maternal-fetal safety, and a percentage of women do not respond to these therapies. Therefore, alternative strategies that directly address the pathophysiology of HDP are required. This article focuses on the potential of the nitrate-nitrite-NO pathway, abundantly present in dark leafy greens and beetroot, as an alternative approach to treating HDP. The objective of this review is to discuss the prospective antioxidant role of nitrate. We hope our discussion paves the way for using nitrate to improve endothelial dysfunction and control oxidative stress, offering a potential therapy for managing HDP.

A full potential all-electron density functional method within generalized gradient approximation is used to investigate the electronic, elastic and transport properties of cubic copper sulphide and copper selenide. The electronic structure suggests metallic behavior with a zero energy band gap for both materials. Elastic property calculations suggest a stiff material with the bulk to shear modulus ratio of 0.35 and 0.44 for Cu2S and Cu2Se respectively. The transport properties were estimated using the Boltzmann transport approach. Seebeck coefficient, electrical conductivity, thermal conductivity, and power factor all suggest a potential p-type conductivity for Cu2S and n-type conductivity for Cu2Se.

Our investigations show that electrochemical corrosion of copper is faster than electrochemical corrosion of aluminium at temperatures below 100oC. Literature data analysis shows that the Al atoms diffuse faster than the Cu atoms at temperatures higher than 475oC, Al rich intermetallic compounds (IMCs) are formed faster in the Cu-Al system, and the Kirkendall plane shifts toward Al side. Electrochemical corrosion occurs due to electric current and due to diffusion. An electronic devise working time, for example, depends on initial copper cover thickness on aluminium wire, connected to the electronic devise, temperature, and volume and dislocation pipe diffusion coefficients, so copper, iron, and aluminium electrochemical corrosion rates are investigated experimentally at room temperature and at temperature 100oC. Intrinsic diffusivities ratios of copper and aluminium at different temperatures and diffusion activation energies in the Cu-Al system are calculated by proposed here methods using literature experimental data. Dislocation pipe and volume diffusion activation energies of pure iron are calculated separately by earlier proposed method using literature experimental data. Aluminium dissolved into NaCl solution as the Al3+ ions at room temperature and at temperature 100oC, iron dissolved into NaCl solution as the Fe2+ (not Fe3+) ions at room temperature and at temperature 100oC, copper dissolved into NaCl solution as the Cu+ ions at room temperature and as the Cu+ and the Cu2+ ions at temperature 100oC. It is founded experimentally that copper corrosion is higher than aluminium corrosion, and ratio of electrochemical corrosion rates, kCu/kAl>1, decreases with temperature increasing, although iron electrochemical corrosion rate doesn’t depend on temperature below 100oC. It is obvious, because melting point of iron is more higher then melting point of copper or aluminium. It is calculated that copper electrochemical corrosion rate is approximately equal to aluminium electrochemical corrosion at temperature about 300oC, so copper can dissolve into NaCl solution mostly as the Cu2+ ions at temperature about 300oC. Ratio of intrinsic diffusivities, DCu/DAl <1, increases with temperature increasing, and intrinsic diffusivity of aluminium could be approximately equal to intrinsic diffusivity of copper at temperature about 460oC.

Copper-based nanomaterials in the last decade attracted many researchers due to their extensive practical applications, unique, inexpensiveness, and wide availability. In addition to this, copper-based nanomaterials possess good thermal stability, and selectivity and also possess high activity. This review emphasis on the recent advances in the synthesis of copper nanomaterials and their wide applications in the field of environmental catalysis. This review aims to fill a significant knowledge gap in the different areas of environmental pollution management. Also, the paper concentrates on the recent applications of copper-based nanomaterials for environmental remediation, including the removal of heavy metals, and degradation of organic pollutants such as pharmaceuticals, and other environmental contaminants. Also, it will be helpful to young researchers in improving the suitability of implementing the Copper nanomaterials in the right way establishing and achieving sustainable goals for environmental remediation.

Mining is one of the main economic activities of several developing countries as Chile. Due to the progressive fall of the ore grades and the increasingly refractory composition of minerals, concentrating plants have increased that has led to an increase in the generation of tailings. Tailings, especially those obtained in the past, have remaining copper and other valuable species in quantities that can potentially be recovered, such as gold, silver, vanadium and rare earth elements. This transforms this abundant waste into a potential source of precious or strategic metals for secondary mining. One of the techniques of solid-liquid separation that allows the processing of solutions with low concentrations of metals corresponds to the adsorption, and more recently the biosorption, which is based on the use of biological matrices that do not constitute an environmental liability after application. Biosorption occurs as a consequence of the wide variety of active functional groups present in the different types of biomass. Bacterial, fungal, plant and algal biomasses have been described as biosorbents, mainly for the treatment of diluted and simple solutions. This work aims to recover copper from leached tailings using biomass of the red algae Gracilaria chilensis as a biosorbent. The tailing samples were taken from an abandoned deposit in the north of Chile and after an acid leaching copper was biosorbed, for which the kinetics of adsorption and the equilibrium isotherms were studied, applying the Freundlich and Langmuir models. Operational parameters such as adsorbent dose, pH and initial metal concentration were studied.

Copper demand for a country's copper industry has a greater pull effect. China's copper consumption in 2015 has accounted for 50% of the world. The scientific forecast of China's copper demands trend is also an important basis for analyzing its future environmental impact. This paper assumes that China's economy will be developing high, medium and low scenarios, and forecasts economic and social indicators such as total GDP, population and per capita GDP in China from 2016 to 2030. Then, predicted the demand of copper resources in China from 2016 to 2030 by the combination of system dynamics model, vector autoregressive moving average model and inverted U-type empirical model. The results show that: (1) in 2020, 2025 and 2030, China's refined copper demand will be 13 Mt, 15 Mt and 15.5 Mt. (2) China's copper demand growth slowed down significantly from 2016-2030. (3) 2025-2030, China's copper resource demand is stable, into the platform of demand growth, the highest peak value in 2027 will be 15.5 Mt. (4) 2030 years later, China's copper resource demand will enter a slow decline.

The orexin/hypocretin neuropeptide family has emerged as a focal point of neuroscientific research following the discovery that this family plays a crucial role in a variety of physiological and behavioral processes. These neuropeptides serve as powerful neuromodulators, intricately shaping autonomic, endocrine, and behavioral responses across species. Notably, they serve as master regulators of vigilance and stress responses; however, their role in complex processes such as food intake, metabolism, and thermoregulation warrant further investigation. This narrative review provides a journey through the evolution of our understanding of the orexin system, from its initial discovery to the promising progress made in developing orexin derivatives. It goes beyond conventional boundaries, striving to synthesize the multifaceted activities of orexins. Special emphasis is placed on domains such as stress response, fear, anxiety, and learning, in which the authors contributed to the literature with original publications. This article demonstrates the orchestrating role of the orexins in several intricate and integrative physiological processes. It also overviews the advancement of orexin pharmacology, which has already yielded some promising successes, particularly in the treatment of sleep disorders. This interdisciplinary approach to studying neuropeptides unveils their significance as vital connectors between transient functional changes and lasting structural adaptations. Ultimately, it advances our understanding of the intricate physiological and behavioral contributions of the orexin/hypocretin neuropeptide family.

With the growing demand for personal protective equipment (PPE) in the face of the pandemic events caused by SARS-COV-2, the opportunity arises for the development of materials with characteristics such as antimicrobial, antiviral, antifungal activity, etc. The use of polymeric nanocomposites based on polyester/copper offers an alternative of great interest due to the versatility of the raw material and the high efficiency of copper as an antimicrobial additive. In this study, textile fibers prototypes with different Cu nanoparticles (CuNP) content were produced using melt-spinning to obtain bi-component multifilament fibers, and melt-blowing to obtain non-woven fabrics. The prototypes were tested against different pathogenic microorganisms such as S. aureus, E. coli, and C. albicans. It was shown that bi-component fibers offer more excellent protection against pathogens, while non-woven fabric only shows activity against E. coli. It was possible to identify that the CuNP were confined exclusively in the outer cover of the bi-component fibers, using different analytical techniques, which may be associated with the increase in antimicrobial activity, compared to the fibers present in the non-woven fabric, even when they present the same CuNP content.

Bioglasses are highly adoptable bone substitute materials, which can be combined with so-called therapeutic ions. These ions have shown to influence underlying molecular processes of the bone regeneration cascade. Moreover, it is known that bone substitutes induce an immune reaction within their implantation area involving macrophages and their pro- and anti-inflammatory subtypes dependent on their chemical composition. However, only poor knowledge exists regarding the influence of therapeutic ions onto the immune reactions and the associated bone healing. Thus, the aim of this work was to investigate the influence of strontium- and copper-doped bioglasses on the induction of M1- and M2-macrophages as well as the implant bed vascularization. (2) Methods: For this study, two alkali glasses were produced on basis of ICIE-16 bioglass via the melt-quench route with the addition of 5 wt% copper or strontium (ICIE16-Cu and ICIE16-Sr). Pure ICIE16 and 45S5 bioglasses were used as control materials. The bioactivity (ion release), chemical composition and the surface pattern were investigated, as well as an in vivo experiment was performed using the subcutaneous implantation model in rats. (3) Results: SEM imaging showed different formations of hydroxyapatite on the surfaces of the bioglass systems after submersion in simulated body fluid. EDX analysis confirmed the doping process by showing the release kinetics. Copper-doped bioglass exhibited a higher ion release than strontium-doped bioglass. Copper induced both a low immune cell migration and triggered a low number of M1- and M2-macrophages but also of blood vessels. The strontium-containing bioactive glass induced higher numbers of M1-macrophages after 30 days. Both copper- and strontium-doped bioglasses induced comparable numbers of M2-macrophages as found in the control groups. (4) Conclusions: Bioglass doping with copper and strontium did not exhibit significant influence on the foreign body response or the implantation bed vascularization in vivo. However, the prepared bioglass systems seemed to be biocompatible.

Measurements of copper and zinc in transfusion-dependent thalassemia (TDT) show contradictory results.Aim of the study: To examine serum levels of these minerals in TDT in relation to iron overload indices and erythron variables. Methods: This study recruited 60 children with TDT and 30 healthy children aged 3-12 years old.Results: Zinc was significantly higher in TDT children than in control children, whilst copper and the copper to zinc ratio were significantly lowered in TDT. Serum zinc was significantly associated with the number of blood transfusions and iron overload variables (including serum iron and TS%) and negatively with erythron variables (including hemoglobin, mean corpuscular volume, mean corpuscular hemoglobin). Serum copper was significantly and negatively associated with the same iron overload and erythron variables. The copper to zinc ratio was significantly correlated with iron, TS%, ferritin, hemoglobin, mean corpuscular volume, and mean corpuscular hemoglobin. Albumin levels were significantly higher in TDT children than in control children. Conclusion: Our results suggest that the increase in zinc in children with TDT may be explained by iron loading anemia and hemolysis and the consequent shedding of high amounts of intracellular zinc into the plasma. Increased albumin levels and treatment with Desferral may further contribute towards higher zinc levels in TDT. We suggest that the elevations in zinc in TDT are a compensatory mechanism protecting against infection, inflammation, and oxidative stress. Previous proposals for prophylactic use of zinc supplements in TDT may not be warranted.

There is an increasing interest in applying environmentally-friendly materials in wood protection technology. This include the use of less toxic active ingredients, as well as better fixation. This study investigates the formulation based on the combination of copper and Saqez resin on the physical and biological resistance properties of poplar wood. Samples were treated by either copper-ethanolamine (Cu/MEA) and/or Saqez resin at various treatment levels. A vacuum pressure procedure was applied. The retention, weight percent gain, water absorption, volumetric swelling, and decay resistance of the samples were then determined. The highest retention and weight percent gain were obtained at the samples treated with the combination of copper-based system and Saqez resin. Additionally, the combination of the copper and Saqez improved the physical properties and decay-resistance against white-rot fungus Trametes versicolor.

Behavior of supported alloyed and de-alloyed platinum-copper catalysts, which contained 14% - 27% wt. of Pt, was studied in the reactions of methanol electrooxidation (MOR) and oxygen electroreduction (ORR) in 0.1 M HClO4 solutions. Alloyed PtCux/C catalysts were prepared by a multistage sequential deposition of copper and platinum onto a Vulcan XC72 dispersed carbon support. De-alloyed PtCux-y/C catalysts were prepared by PtCux/C materials pretreatment in acid solutions. The effects of the catalysts initial composition and the acid treatment condition on their composition, structure, and catalytic activity in MOR and ORR were studied. Functional characteristics of platinum-copper catalysts were compared with those of commercial Pt/C catalysts when tested, both in an electrochemical cell and in H2/Air membrane-electrode assembly (MEA). It was shown that the acid pretreatment of platinum-copper catalysts practically does not have negative effect on their catalytic activity, but it reduces the amount of copper passing into the solution during the subsequent electrochemical study. The activity of platinum-copper catalysts in the MOR and the current-voltage characteristics of the H2/Air PEMFC MEAs measured in the process of their life tests were much higher than those of the Pt/C catalysts.

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

Fetal Alcohol Spectrum Disorders (FASD) represent a continuum of lifelong impairments resulting from prenatal exposure to alcohol, with significant global impact. The “spectrum” of disorders includes a continuum of physical, cognitive, behavioral, and developmental impairments, which can have profound and lasting effects on individuals throughout their lives impacting their health, social interactions, psychological well-being and every aspect of their lives. This narrative paper explores the intricate relationship between oxidative stress and epigenetics in FASD pathogenesis and its therapeutic implications. Oxidative stress, induced by alcohol metabolism, disrupts cellular components, particularly in the vulnerable fetal brain, leading to aberrant development. Furthermore, oxidative stress is implicated in epigenetic changes, including alterations in DNA methylation, histone modifications, and microRNA expression, which influence gene regulation in FASD patients. Moreover, mitochondrial dysfunction and neuroinflammation contribute to epigenetic changes associated with FASD. Understanding these mechanisms holds promise for targeted therapeutic interventions. This includes antioxidant supplementation and lifestyle modifications to mitigate FASD-related impairments. While preclinical studies show promise, further clinical trials are needed to validate these interventions' efficacy in improving clinical outcomes for individuals affected by FASD. This comprehensive understanding of the role of oxidative stress on epigenetics in FASD underscores the importance of multidisciplinary approaches for diagnosis, management, and prevention strategies. Continued research in this field is crucial for advancing our knowledge and developing effective interventions to address this significant public health concern.

Background: Clinical trails have revealed that patients with depression generally accompanied with learning and memory impairment, which critically impact on individual’s health and development. Danggui-Shaoyao-San (DSS), a famous Chinese complex prescription, significantly overcame depression and relieved cognitive disorder based on previous research and publication. However, its effectsand potential mechanism against chronic restraint stress (CRS) remained unknown. Methods: CRS animal model was established and mice were divided to six groups while they were oral administrated with Danggui-Shaoyao-San at doses of 1.25, 2.5 and 5 g/kg for 14 days. Emotional and cognitive performances were detected by behavior tests, meanwhile neural plasticity and its molecular mechanism were examined by Dil staining, western blot and immunofluorescence. Results: DSS treatment dose-dependently improved locomotion ability in open filed test, overcame depression behavior in forced swimming test and elevated plus maze test, enhanced learning and memory ability in Morris water maze test. CRS decreased number of total spines and mushroom spines, while DSS treatment dose-dependently restored these by Dil staining. Expression of BDNF and GluR1 were significantly down-regulated in CRS group, which were significantly normalized by DSS. Conclusions: DSS treatment dose-dependently reversed CRS-induced cognitive impairments by inducing structural remodeling of neurons.

Stress urinary incontinence (SUI) influences the quality of life of women. The research applied ICIQ LUTS qol (The International Consultation Incontinence Questionnaire Lower Urinary Tract Symptoms quality of life) as a tool to measure the quality of life (QOL) of patients with stage 1 SUI in many areas. 140 perimenopausal women who participated in a urodynamic test at Department of Gynecology, Endocrinology and Gynecologic Oncology, Pomeranian Medical University, Police, Poland in the years 2013-2015 were enrolled in the study. Patients were divided into two groups: A and B. Two questionnaires were applied: the author’s original questionnaire and the standardized ICIQ LUTS qol. Gymnastic plans were recommended 4 times per week for the period of 3 months. The plan for group A included the exercises of pelvic floor muscles (PFM) with the simultaneous tension of the transverse abdominal muscle (TrA) and for group B included the exercises of PMF without TrA. The evaluation of the quality of life of patients with stage 1 SUI with the use of ICIQ LUTS qol among patients from groups A and B after therapy showed a significant improvement in most areas. More impact is observed in the physiotherapy of both PFM with TrA.

Due to its built-up chemoresistance after prolonged usage, the demand for replacing platinum in metal-based drugs (MBD) is rising. The first MBD approved by the FDA for cancer therapy was cisplatin in 1978. Even after nearly four and a half decades of trials, there has been no significant improvement in osteosarcoma (OS) therapy. In fact, many MBD have been developed, but the chemoresistance problem raised by platinum remains unresolved. This motivates us to elucidate the possibilities of the copper and zinc (CuZn) combination to replace platinum in MBD. Thus, the anti-chemoresistance properties of CuZn and their physiological functions for OS therapy are highlighted. Herein, we summarise their chelators, main organic solvents, and ligand functions in their structures that are involved in anti-chemoresistance properties. Through this review, it is rational to discuss their ligands’ roles as biosensors in drug delivery systems. Hereafter, an in-depth understanding of their redox and photoactive function relationships is provided. The disadvantage is that the other functions of biosensors cannot be elaborated on here. As a result, this review is being developed, which is expected to intensify OS drugs with higher cure rates. Nonetheless, this advancement intends to solve the major chemoresistance obstacle towards clinical efficacy.

The trace element copper (Cu) is part of our nutrition and essentially needed for several cuproenzymes that control redox status and support the immune system. In blood, the ferroxidase ceruloplasmin (CP) accounts for the majority of circulating Cu and serves as transport protein. Both Cu and CP behave as positive, whereas serum selenium (Se) and its transporter selenoprotein P (SELENOP) behave as negative acute phase reactants. In view that coronavirus disease (COVID-19) causes systemic inflammation, we hypothesized that biomarkers of Cu and Se status are regulated inversely, in relation to disease severity and mortality risk. Serum samples from COVID-19 patients were analysed for Cu by total reflection X-ray fluorescence and CP was quantified by a validated sandwich ELISA. The two Cu biomarkers correlated positively in serum from patients with COVID-19 (R=0.42, p&lt;0.001). Surviving patients showed higher mean serum Cu and CP concentrations in comparison to non-survivors ([mean+/-SEM], Cu; 1475.9+/-22.7 vs. 1317.9+/-43.9 µg/L; p&lt;0.001, CP; 547.2.5 +/- 19.5 vs. 438.8+/-32.9 mg/L, p=0.086). In contrast to expectations, total serum Cu and Se concentrations displayed a positive linear correlation in the patient samples analysed (R=0.23, p=0.003). Serum CP and SELENOP levels were not interrelated. Applying receiver operating characteristics (ROC) curve analysis, the combination of Cu and SELENOP with age outperformed other combinations of parameters for predicting risk of death, yielding an AUC of 95.0%. We conclude that the alterations in serum biomarkers of Cu and Se status in COVID-19 are not compatible with a simple acute phase response, and that serum Cu and SELENOP levels contribute to a good prediction of survival. Adjuvant supplementation in patients with diagnostically proven deficits in Cu or Se may positively influence disease course, as both increase in survivors and are of crucial importance for the immune response and antioxidative defence systems.

Friction stir alloying (FSA) of commercially pure Cu with Ni, Zn, and Mg is implemented in the current study. The successfully fabricated alloy structure has been scrutinized in terms of mechanical and micro-structural standpoints. Energy-dispersive X-ray spectroscopy revealed a uniform distribution of alloying elements and coalescence at the atomic level. The compositional and grain size heterogeneity is managed in the stir zone, which pave way for microstructural control using FSA. Thus, the present study carries significance for the development of novel materials whose fabrication requires temperature far below the melting point of base metals. Ultra-refinement of grains is found to accompany the alloying process, with ~ 440 nm being the smallest grain size. Maximum and average micro-hardness enhancement of 18.4 % and 6 % is observed for the fabricated alloy. Tensile properties have also been investigated and co-related with the micro-structural morphology. The shift towards grain bimodality has also been reported, which is a highly sought property in the present day, especially to overcome the strength-ductility trade-off.

CuAl8Fe5Ni4Zn4Sn1 (OF 2238) is a new lead-free copper alloy for plain bearing applications that was first officially presented in a scientific journal in 2020. Soon after its invention, the use of the alloy for connecting rod bushings in heavy duty internal combustion engines was promoted and validated with customers. The aim of this article is to describe the material properties of the new alloy in more detail than previously and explain how the advantageous properties of CuAl8Fe5Ni4Zn4Sn1 are generated. At the beginning of the article, the general development trends in the field of copper alloys for sliding applications are presented. This is followed by a presentation of the latest research results about CuAl8Fe5Ni4Zn4Sn, before concluding with a brief summary and future outlook, emphasizing on the fact that recent trends in copper-based sliding applications show great additional potential for further material developments.

Porous metals possess low bulk density, large specific strength, high stiffness and special thermal, electromagnetic and acoustic conductivity, so that porous metals are widely used in filtration and separation, flame retardant explosion-proof, biomedical application, etc. Compared with its corresponding dense metal, the presence of porous structures also leads to different corrosive performances of porous metal. So, some researches have utilized weight loss method, electrochemical impedance to evaluate porous metals’ corrosion behavior; however, the influence of pore structure on metal corrosion is still controversial, and present methods used for analyses of porous metals’ corrosion are statistical averages of the corrosion behavior of the entire porous material, which cannot accurately reflect the corrosion behavior inside the pore structure. Herein, we prepare porous copper samples with 0, 24, 72, 96 pores using mechanical process, and employ scanning kelvin probe combined with electrochemical polarization curve and impedance spectroscopy to test the corrosion performance of the porous copper in static and dynamic NaCl solution. The relevant results indicate that in static solution, the corrosion resistance of samples gradually increases with the rise of the number of pores. By contrast, the sample with 24 pores exhibits more susceptible to corrosion than the sample without pore.

Copper toxicity has been a selective pressure on the sea-ice bacteria due to its widespread occur-rence in Antarctica. Here, with a combined biochemical and metabolomic approach, the Cu2+ ad-aptation mechanisms of Antarctic bacteria were analyzed. Heavy metal resistance pattern of Pb2+ > Cu2+ > Cd2+ > Hg2+ > Zn2+ was observed. Copper treatment did increase the activity of antioxidants and enzymes, maintaining cellular redox state balance and normal cell division and growth. Metabolomics analysis demonstrated that fatty acids, amino acids, and carbohydrates played dominant roles in copper stress adaptation. The results indicated that the adaptation mechanisms of strain O5 to copper stress included protein synthesis and repair, accumulation of organic per-meable substances, up-regulation of energy metabolism, and formation of fatty acids. This study increases the resistance mechanism understanding of Antarctic strains to heavy metals in extreme environments.

Heavy metals contamination in groundwater often occurs in various industrial processes. Stud-ies have confirmed that polysulfide could reduce hexavalent chromium to trivalent chromium, achieving the effect of in-situ stabilization. For other heavy metals contamination in groundwa-ter, whether polysulfide also had a stabilizing ability to achieve in-situ remediation. This re-search focused on heavy metals except for chromium that often contaminated in groundwater, including lead, nickel, zinc, copper, and cadmium to explore the feasibility of using calcium polysulfide (CaSx) as an in-situ stabilization technology for these heavy metals contamination groundwater. Results showed that CaSx had a great removal efficiency for heavy metals lead, nickel, zinc, copper, and cadmium. However, for nickel, zinc, copper and cadmium, when CaSx was added excessively, complexes would be formed, causing the result of re-dissolve and this would also reduce the removal efficiency. Since it is difficult to accurately control the dosage of agents for in-situ groundwater remediation, the concentration of re-dissolved nickel, zinc, cop-per, and cadmium may not be able to meet the groundwater control standards. CaSx had high lead removal efficiency, and it would not cause re-dissolution due to excessive CaSx dosing. CaSx can be used as an in-situ stabilization technique for lead contaminated groundwater.

Researchers from around the world are looking for better and cheaper ozone production. One of the methods increasing the efficiency of ozone production is the use to a rotating electrode presented in this paper. Experiments were carried out which shows that the most important parameters are the materials used on the electrodes and the condition of its surface. The metallographic investigations of the electrodes after continuous monthly work was made, which show how the raids layers are formed. As a result of working in a highly oxidizing environment, the electrode is oxidized in the process of chemical corrosion. It is obvious that the layer of corrosion products created during the work of the plasma reactor isolates the surface of the electrode, which reduces the intensity of the electric field, causing a decrease in the amount of plasma generated, which is a direct cause of lowering the concentration of ozone during this process. The dynamics of plasma generation process and the type of electrode material working in changing process conditions are the decisive factors influencing the concentration of ozone produced. The influence of the medium, which is the electrode material, depends mainly on its resistance to corrosion in the environment of dynamically changing conditions, e.g. electrode rotation, oxygen flow through the rotating electric field and the long monthly working time of the plasma reactor.

Background: Music evokes positive emotions and reduces stress and anxiety. Operating Room (OR) staff face various challenges which can lead to high levels of stress. The aim of the study is to assess whether listening to music during intraoperative phases improves the work environment by reducing anxiety and stress in the entire surgical team. Methods. A prospective observational study was conducted from February to September 2023, involving medical personnel, nursing staff, and nursing students. They were divided into two groups: Group 1 with music during surgical procedures, and Group 2 without music. Participants were administered two validated instruments: the Zung Anxiety Self-Assessment Scale (SAS) to measure anxiety, and the Positive and Negative Affect Schedule to assess emotions generating stress. Additional items were included for demographics, job satisfaction, and the organization method. Results. Music did not impact anxiety but increased positive emotions while reducing negative ones. Music had an ancillary effect, highlighting the need for significant organizational interventions aimed at increasing operator satisfaction, including voluntary rather than mandatory assignments for nursing staff. Conclusions. Music appears to reduce stress in the intraoperative team when supported by a positive work environment in which assigned operators have chosen to work in the OR.

Tourism is the main economic sector in the Balearic Islands (Spain) and hotel housekeepers (HHs) are a large occupational group, in which stress is becoming a major issue. This study aims at exploring in-depth factors perceived as stressors by HHs and key-informants, and their effects on work-life balance (WLB). A qualitative design with phenomenological approach was used, conducting six focus groups with 34 HHs and 10 individual interviews with key-informants. Results were analyzed adopting the job demands-resources model and a gender perspective. High demands –e.g work overload, time pressure, physical burden...-, lack of enough resources and little control –derived from role conflict, unexpected events...- were the most important factors explaining HHs’ stress. Additionally, this imbalance was perceived as leading to health problems –mainly musculoskeletal disorders-. Working schedule was mentioned as a facilitator to WLB, whereas an imbalance between job demands and resources led to work-home conflict –preventing them from enjoying leisure time-. Multiple roles at work and at home increased their stress. HHs experienced their job as invisible and unrecognised. Regarding practical implications, our recommendations for hotel organization include reducing workload and increasing resources, which would improve the job demands-resource balance, diminish negative mental and physical outcomes and improve WLB.

Green synthesis using plant extracts has emerged as an eco-friendly, clean, and viable strategy alternative to chemical and physical approaches. The leaf, stem, and root extracts of Lannea discolor was utilized as a reducing and stabilizing agent in the synthesis of gold (AuNPs) and copper (CuNPs) nanoparticles. The formation of AuNPs and CuNPs confirmed by their color change, was characterised by UV–Vis Spectroscopy (UV- Vis), Scanning electron microscopy analysis and energy dispersive x-ray (SEM-EDX), Transmission Electron Microscopy (TEM), and Fourier Transform Infrared Spectroscopy (FTIR), coupled with minimum concentration inhibitory (MIC) antibacterial assays. AuNFs, NPs and CuNPs peaked at wavelengths in the ranges of 316, 544 and 564 nm respectively. TEM showed unexpected nanoflowers (30 – 97 nm) in the leaf extracts and spherical NPs (10 -33 nm; 9.3 – 37.5) from stem and root extracts, while spherical CuNPs (20 – 104 nm), were observed from all the extracts. EDX was able to confirm the presence of metal salts and FTIR revealed stable capping agents. AuNPs and NFs from L. discolor extracts showed appreciable antibacterial activity against Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, Klebsiella pneumoniae and Bacillus subtilis, when compared to the plant extracts, while none was observed from the CuNPs. These AuNPs and CuNPs are particularly appealing in a variety of applications in the biomedical as well as conductivity manufacturing, due to their shapes and sizes and economical and environmentally friendly production.

Macroautophagy/autophagy plays an important role in cellular copper clearance. The means by which the copper metabolism and autophagy pathways interact mechanistically is vastly unexplored. Dysfunctional ATP7B, a copper-transporting ATPase, is involved in the development of monogenic Wilson disease, a disorder characterized by disturbed copper transport. Using in silico prediction, we found that ATP7B contains a number of potential binding sites for LC3, a central protein in autophagy pathway, so-called LC3 interaction regions (LIRs). The conserved LIR3, located at the C-terminal end of ATP7B, was found to directly interact with LC3B in vitro. Replacing the two conserved hydrophobic residues W1452 and L1455 of LIR3 significantly reduced interaction. Furthermore, autophagy was induced in normal human hepatocellular carcinoma cells (HepG2) leading to enhanced colocalization of ATP7B and LC3B on the autophagosome membranes. By contrast, HepG2 cells deficient of ATP7B (HepG2 ATP7B-/-) showed autophagy deficiency at elevated copper condition. This phenotype was complemented by heterologous ATP7B expression. These findings suggest a cooperative role of ATP7B and LC3B in autophagy-mediated copper clearance.

The airflow carried by artificial aeration provides oxidant O2 for microbial growth and mineral dissolution in heap bioleaching. To investigate the effect of forced aeration rate on bioleaching of low-grade copper sulfide ores, column bioleaching experiments with six columns were conducted in the aeration range of 0~150 L/h at 30~45 ℃. The results showed that when the aeration rate was higher than 95 L/h, the proportions of heap settlement and fine particles mass were much greater than that without aeration. The final total Fe concentration and bacterial cell numbers in pregnant leach solution increased with the increase of aeration rate.The final concentrations of Cu2 + in the mother liquor under aeration conditions of 60-150 L / h were 1.411, 1.432, 1.498, 1.491 and 1.583 g / L, respectively, which were higher than 1.345 g / L under non-aeration conditions. When the aeration rate was 150 L / h, the final Cu leaching rate was 80.1 %, which was 11.4 % higher than that without aeration ( 68.7 % ). Furthermore, in the early stage of leaching, copper leaching rate with 95 L/h aeration rate remained the highest. 结论Artificial aeration accelerates the bioleaching of low-grade copper sulfide ores by improving porosity structure, temperature range of bacterial activity and microbial catalyzed dissolution of targeted minerals.

Copper oxide nanoparticles (CuONPs) were synthesized using an eco-friendly method and their antimicrobial and biocompatibility properties were determined. The supernatant and extract of the fungus Ganoderma sessile yielded small, quasi-spherical NPs with an average size of 4.5 ± 1.9 nm and 5.2 ± 2.1 nm, respectively. CuONPs showed antimicrobial activity against Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa. Minimum inhibitory concentration (MIC) for E. coli and S. aureus was 15.9 µg/mL for nanoparticles (NPs) using the supernatant (CuONPs-S) and 16.5 µg/ml for NPs using the extract (CuONPs-E). Lower concentrations were required for P. aeruginosa inhibition. Ultrastructural analysis revealed the presence of the small CuONPs all through the bacterial cells. Finally, the toxicity of CuONPs was analyzed in three mammalian cell lines: hepatocytes (AML-12), macrophages (RAW 264.7) and kidney (MDCK). Low concentrations (<15 µg/ml) of CuONPs-E were non-toxic to kidney cells and macrophages, and the hepatocytes were the most susceptible to CuONPs-S. The results obtained suggest that the CuONPs synthesized using the extract of the fungus G. sessile, could be further evaluated for the treatment of superficial infectious diseases.

This work aimed to carry out a bioremediation study to evaluate the resistance of Penicillium sp. isolated from kefir grains for the treatment of copper. The fungal culture medium was prepared using a 2% malt-agar medium at pH 7.0 in which Penicillium sp. was inoculated. Penicillium sp. growing in a liquid medium showed a decrease in biomass in presence of Cu(NO3)2 (800 mg.L-1), suggesting that the metal impacts the growth rate of the fungus. Moreover, the combined factors of pH and the presence of the inorganic contaminant impacted the radial growth of the fungus, causing inhibition of 73% at pH 4.0, 75% at pH 7.0, and 77% at pH 9.0 in liquid medium compared to control. However, images obtained with scanning electron microscopy showed the integrity of the fungus cell, even at high doses of copper in the medium. Therefore, it can be concluded that Penicillium sp. isolated from kefir grain can bioremediate the environment and that the harmful effects of heavy metals can be minimized as a result biosorption. Although the growth of Penicillium sp. is inhibited, such retardation requires high doses of copper nitrate, thus ensuring the use of this microorganism for protection against the harmful effects of non-essential copper in the environment.

The color of a thin copper oxide layer formed on a copper plate was transformed from reddish-brown into blue-purple by irradiation with 5 keV Ar+ ions to a fluence as low as 1 1015 Ar+ cm–2. In the unirradiated copper oxide layer, the copper valence state of Cu2+ as well as Cu+ and/or Cu0 was included as indicated by the presence of a shake-up satellite line in a photoemission spectrum. While for the irradiated one, the satellite line decreased in intensity, indicating that irradiation resulted in the reduction from Cu2+ to Cu+ and/or Cu0. Furthermore, nuclear reaction analysis using a 16O(d, p)17O reaction with 0.85 MeV deuterons revealed a significant loss of oxygen (51015 O atoms cm–2) in the irradiated layer. Thus, the chromatic change observed in the present work originated in the irradiation-induced reduction of a copper oxide.

Compelling epidemiologic data support the critical role of dietary fructose in the epidemic of obesity, metabolic syndrome and nonalcoholic fatty liver disease (NAFLD). The metabolic effects of fructose on the development of metabolic syndrome and NAFLD are not completely understood. High fructose intake impairs copper status, and copper-fructose interactions have been well documented in rats. Altered copper-fructose metabolism leads to exacerbated experimental metabolic syndrome and NAFLD. A growing body of evidence has demonstrated that copper levels are low in NAFLD patients. Moreover, hepatic and serum copper levels are inversely correlated with the severity of NAFLD. Thus, high fructose consumption and low copper availability are considered two important risk factors in NAFLD. However, the causal effect of copper-fructose interactions as well as the effects of fructose intake on copper status remain to be evaluated in humans. The aim of this review is to summarize the role of copper-fructose interactions in the pathogenesis of the metabolic syndrome and discuss the potential underlying mechanisms. This review will shed light on the role of copper homeostasis and high fructose intake and point to copper-fructose interactions as novel mechanisms in the fructose induced NAFLD.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

Carbonous nanomaterials are promising additives for composite coatings for heat-dissipation materials because of their excellent thermal conductivity. Here, copper/carbonous nanomaterial composite coatings were prepared using nanodiamond (ND) as the carbonous nanomaterial. The copper/ND composite coatings were electrically deposited onto copper substrates from a continuously stirred copper sulfate coating bath containing NDs. NDs were dispersed by ultrasonic treatment, and the initial bath pH was adjusted by adding sodium hydroxide solution or sulfuric acid solution before electrodeposition. The effects of various coating conditions—the initial ND concentration, initial bath pH, stirring speed, electrical current density, and the amount of electricity—on the ND content of the coatings were investigated. Furthermore, the surface of the NDs was modified by hydrothermal treatment to improve ND incorporation. A higher initial ND concentration and a higher stirring speed increased the ND content of the coatings, whereas a higher initial bath pH and a greater amount of electricity decreased it. The electrical current density showed a minimum ND content at approximately 5 A/dm². Hydrothermal treatment, which introduced carboxyl groups onto the ND surface, improved the ND content of the coatings. A copper/ND composite coating with a maximum of 3.85 mass% ND was obtained.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

The direct methane to methanol (MTM) oxidation is a grand challenge in catalysis, with profound economical implications for the modern chemical industry. Bioinspired metal-organic frameworks (MOFs) with active iron and copper sites have been emerging very recently as innovative catalytic platforms to accomplish the MTM conversion under mild conditions. This review discusses the current state of the art regarding the application of MOFs with iron and copper catalytic centers to perform the MTM reaction, with a focus on the diverse spectroscopic techniques used to unveil the electronic and structural properties of the MOF catalysts at a microscopic level. We explore the synthetic strategies employed to incorporate iron and copper sites into different MOF topologies, the efficiency and selectivity of the iron- and copper-bearing MOF catalysts, and the ensuing MTM reaction mechanisms proposed on the basis of spectroscopic characterization supported by theory. In particular, we evidence how the combination of complementary spectroscopic tools probing different regions of the electromagnetic spectrum is particularly useful to reach a satisfactory understanding of the key reaction pathways and intermediates. Finally, we provide a critical perspective on future directions to advance the use of MOFs to accomplish the MTM reaction.

Mining and processing tailings often contain significant amounts of valuable metals, that can represent valuable sources of secondary raw materials. Especially this is case in early-stage operations, in which the head grades were higher, and the tailings were higher grade. These tailings can also present a substantial risk to the environment. Serbia has copper deposits which have been exploited since ancient times, and these operations have generated large amounts of mineral processing tailings. The main objective of this study is to show how valuables can be recovered from chemically and mineralogically challenging tailings. After detailed chemical and mineralogical characterization, the laboratory scale flotation tests focused on evaluating the effect of particle size, different types of collectors, pH, and pulp potential. Based on the test work, copper and gold can be recovered effectively into pyrite concentrate