In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

This study was to identify clinical cancer biomarkers for recurrent gastric cancer survivors using artificial intel-ligence. From a hospital-based cancer registry database in Taiwan, the datasets of the incidence of recurrence and clinical risk features were included in 2476 gastric cancer survivors. We benchmarked Random forest with MLP, C4.5, AdaBoost, and Bagging algorithms on metrics and leveraged synthetic minority oversampling technique (SMOTE) for imbalanced dataset issues, cost-sensitive learning for risk assessment, and SHapley Additive ex-Planations (SHAP) for feature importance analysis in this study. Our proposed Random forest outperformed the other models with an accuracy of 87.9%, a recall rate of 90.5%, an accuracy rate of 86% and F1 of 88.2% on re-current category by a 10-fold cross-validation in a balanced dataset. We identified clinical features of recurrent gastric cancer, which are the top five features, stage, number of regional lymph node involvement, Helicobacter pylori, BMI(body mass index), and gender, which significantly affect the prediction model's output, are worth paying attention to in the following causal effect analysis. Using an artificial intelligence model, the risk factors for recurrent gastric cancer could be identified and cost-effectively ranked according to their feature importance. In addition, they should be crucial clinical features to provide physicians with the knowledge to screen high-risk patients in gastric cancer survivors as well.

This paper presents a comprehensive and adaptive framework for orchid conservation programs illustrated with data from published and unpublished case studies. There is a specific focus on West Australian terrestrial orchids, but many of the approaches have universal relevance. Aspects of the framework include (1) setting appropriate objectives, (2) establishing effective collaborations between scientists, volunteers and regulators to fill knowledge and funding gaps, (3) use of survey and demographics data to determine extinction risks and management requirements for species, (4) effective habitat management to overcome threats such as grazing, (5) finding potential new habitats by modelling climate and site data, (6) investigating the effectiveness of pollinators and (7) using seed baiting to detect mycorrhizal fungi. The relative cost and effectiveness of different methods used to propagate orchids for translocation are compared. Methods known to be successful, in order of complexity, include placement of seed in situ, vegetative propagation, symbiotic germination in non-sterile organic matter, symbiotic germination in sterile culture, asymbiotic sterile germination and clonal division in tissue culture. These form a continuum of complexity, cost, time required, faculties needed, as well as the capacity to maintain genetic diversity and produce seedlings preadapted to survive in situ. They all start with seed collection and lead to seed storage, living collections used as tuber banks and seed orchards, as well as translocation for conservation. They could also lead to commercial availability and sustainable ecotourism, both of which are needed to reduce pressure on wild plants. Overall, there has been a strong preference to use relatively complex, expensive and time-consuming methods for orchid conservation, despite evidence that simpler approaches have also been successful. These simpler methods, which include in situ seed placement and non-sterile germination on inorganic substrates, should be trialled in combination with more complex orchid propagation methods as part of an adaptive management framework. It is essential that orchid conservation projects harness the unique biological features of orchids, such as abundant seed production and mycorrhizal fungi which are far more widespread than their hosts. This is necessary to increase the efficiency and coverage of recovery actions for the largest and most threatened plant family.

Climate change from anthropogenic activities represents a serious threat to life in earth. Agriculture releases significant emissions of greenhouse gases (GHG), but also offers low-cost opportunities to mitigate GHG emissions. This paper assesses agricultural GHG emissions in Aragon, one important and representative region for agriculture in Spain. The Marginal Abatement Cost Curve (MACC) approach is used to analyze the abatement potential and cost-efficiency of mitigation measures under several scenarios, with and without taking into account the interaction among measures and their transaction costs. The assessment identifies the environmental and economic outcomes of different combinations of measures. Moreover, we develop future mitigation scenarios for agriculture toward the year 2050, in order to assess the impacts on GHG emissions. Results highlight the importance of assessing biophysical processes in mitigation measures, and the significant effects of interactions between measures that reduce the abatement potential and worsen the cost-efficiency. The inclusion of transaction costs provides a better ranking of measures and a more accurate estimation of implementation costs. The scenario analysis shows how the combinations of measures could reduce emissions and promote sustainable agriculture in the future. Keywords: Climate change; mitigation measures; biophysical processes; cost-efficiency; abatement costs; transaction costs; policy scenarios.

Recent technological advancements in conservation genetics and genomics have resulted in diverse tools for aiding conservation of species. The precision and resolution of high throughput sequencing technologies provide valuable insights to aid conservation decisions, but these technologies are often financially unfeasible or unavailable in resource constrained countries. Inter-Simple Sequence Repeat (ISSR) markers, when combined with sensitive automated detection systems, provide a simple, cheap means to investigate genetic diversity and discriminate closely related species. Here we apply this technology to assess genetic diversity and taxonomic delimitation in the Encephalartos eugene-maraisii species complex, a highly threatened, taxonomically dubious group of cycads in South Africa. Silica dried cycad leaflets were extracted using the Oktopure robot employing Sbeadex chemistry and amplified with fluorescently tagged ISSR primers. Band presence was scored with an ABI 3130 genetic sequencer under three different fluorescence cut-off values. Phenetic analyses were performed in NTSYS software while Bayesian analysis was performed in STRUCTURE, and haplotype network analysis, AMOVA and Tajima’s D statistic was computed with PopART. Our analyses support taxonomic singularity of E. dyerianus, E. dolomiticus and E. eugene-maraisii. Relationships between E. nubimontanus and E. cupidus remain uncertain. E. middelburgensis samples showed no clustering but had poor amplification success. This study demonstrated the suitability of automated ISSR fingerprinting as a method for plant conservation studies, especially in resource-constrained countries.

Biodiversity conservation questions human practices towards biodiversity and, therefore, largely conflicts with ordinary societal aspirations. Decisions on the location of protected areas, one of the most convincing conservation tools, reflect such a competitive endeavor. Operations Research (OR) brings a set of analytical models and tools capable of resolving the conflicting interests between ecology and economy. Recent technological advances have boosted the size and variety of data available to planners, thus challenging conventional approaches bounded on optimized solutions. New models and methods are requested to use such a massive amount of data in integrative schemes addressing a large variety of concerns. Here, we provide an overview on the past, present and future challenges that characterize spatial conservation models supported by OR. By enlarging the spatial, temporal, taxonomic and societal horizons of biodiversity conservation planners navigate around multiple bio-socioeconomic equilibria and are able to decide on cost-effective strategies to improve biodiversity persistence.

Electromagnetic actuation can support many fields of technology, such as robotics or biomedical applications. In this context, fully understanding the system behavior and proposing a low-cost package for feedback control is challenging. Modeling the electromagnetic force is particularly tricky because it is a nonlinear function of the actuated object’s position and coil’s current. Measuring in real time the position of the actuated object with the precision required for accurate motion control is also nontrivial. In this study, we propose a novel, cost-effective electromagnetic set-up to achieve position control via visual feedback. We actuate vertically and under different experimental conditions a 10 mm diameter steel ball hanging on a low-stiffness spring, demonstrating good tracking performance (the position error remains within ±0.5 mm with a negligible phase delay in the best scenarios). The experimental results confirm the feasibility of the proposed set-up, which is characterized by minimum complexity and realized with off-the-shelf and cost-effective components. For these reasons, such a contribution helps to understand and apply electromagnetic actuation even further.

Environmental estrogen pollution and estrogen effects on the female reproduction system are well-recognized scientifically. Among the estrogens, 17 β-estradiol is a priority in environmental estrogen pollution, and it is also a major contributor to estrogen which regulates the female reproduction system. 17 β-estradiol is carcinogen and has a tumor promotion effect relating to breast cancer, lung cancer and others. It also affects the psychological well-being such as depression, fatigue and others. Thus, a simple method of detection of 17 β-estradiol will be important for both environmental estrogen pollution and women’s health care. This study demonstrates a simple-use, cost effective 17 β-estradiol biosensor system which can be used for both environment and women’s health care applications. The bio-recognition mechanism is based on the influence of the redox couple, K₃Fe (CN) ₆/K₄Fe (CN) ₆ by the interaction between 17 β-estradiol antigen and its α-receptor (ER- α; α-estrogen antibody). The transduction mechanism is an electrochemical analytical technique, differential pulse voltammetry (DPV). The levels of 17 β-estradiol antigen studied was between 2.25 pg/mL to 2,250 pg/mL, Phosphate buffered saline (PBS), tap water from the Cleveland regional water district, and simulate urine were used as the test media covering the potential application areas for 17 β-estradiol detection. An interference study by testosterone which has a similar chemical structure and molecular weight as those of 17 β-estradiol was carried out, and this 17 β-estradiol biosensor showed excellent specificity without any interference by similar chemicals.

OBJECTIVE: Although 3D-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. METHODS: We have devised a method of 3D modeling using DICOM images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (ie, tumors) in contrasting color. RESULTS: An array of organ solid-tumor models were printed via Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p<.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glangular size/contour and tumor location, readily approximating the surgical specimen. CONCLUSIONS: This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

Ever since Varela and Maturana proposed the concept of autopoiesis as the minimal requirement for life, there has been a focus on cellular systems that erect topological boundaries to separate themselves from their surrounding environment. Here we reconsider whether the existence of such a spatial boundary is strictly necessary for self-producing entities. This work presents a novel computational model of a minimal autopoietic system inspired by dendrites and molecular dynamics simulations in three-dimensional space. A series of simulation experiments where the metabolic pathways of a particular autocatalytic set are successively inhibited until autocatalytic entities that could be considered autopoietic are produced. These entities maintain their distinctness in an environment containing multiple identical instances of the entities without the existence of a topological boundary. This gives rise to the concept of a metabolic boundary which manifests as emergent self-selection criteria for the processes of self-production without any need for unique identifiers. However, the adoption of such a boundary comes at a cost, as these autopoietic entities are less suited to their simulated environment than their autocatalytic counterparts. Finally, this work showcases a generalized metabolism-centered approach to the study of autopoiesis that can be applied to both physical and abstract systems alike.

We have an unprecedented ability to analyze and map the Earth’s surface, as deep learning technologies are applied to an abundance of Earth observation systems collecting images of the planet daily. In order to realize the potential of these data to improve conservation outcomes, simple, free, and effective methods are needed to enable a wide variety of stakeholders to derive actionable insights from these tools. In this paper we demonstrate simple methods and workflows using free, open computing resources to train well-studied convolutional neural networks and use these to delineate objects of interest in publicly available Earth observation images. With limited training datasets (<1000 observations), we used Google Earth Engine and Tensorflow to process Sentinel-2 and National Agricultural Imaging Program data, and use these to train U-Net and DeepLab models that delineate ground mounted solar arrays and parking lots in satellite imagery. The trained models achieved 81.5% intersection over union between predictions and ground-truth observations in validation images. These images were generated at different times and from different places from those upon which they were trained, indicating the ability of models to generalize outside of data on which they were trained. The two case studies we present illustrate how these methods can be used to inform and improve the development of renewable energy in a manner that is consistent with wildlife conservation.

Ecological and environmental damage caused by oil spillage has attracted great attention. Used cigarette filter (CF) has also caused negative environmental consequences. Converting CF to economical materials is a feasible way to address these problems. In this study, we demonstrate a simple method for production of a highly hydrophobic absorbent from CF. CF was modified by using different volume ratios of octadecyltrichlorosilane and methyltrimethoxysilane. When the volume ratio was 3:2, the modified CF had the high water contact angle of 155°. It could selectively and completely absorb silicone oil from an oil-water mixture and showed a good absorption capacity of 38.3 g/g. The absorbed oil was readily and rapidly recovered by simple mechanical squeezing, and it could be reused immediately without any additional treatments. The as-obtained superhydrophobic modified CF retained an absorption capacity of 80% for pump oil and 82% for silicone oil after 10 cycles. The modified CF showed good elasticity in the test of repeated use. The present study provides novel design of a functional material for development of hydrophobic absorbents from used CF via a facile method toward oil spillage cleanup as well as a new recycling method of CF to alleviate the environmental impact.

Temperature increases mediated through climate change threaten the survival of species. It is of foremost importance to engage citizens and future generations in understanding the mechanisms through which temperatures imposes its affect. For educators though this is not straight forward as tools for examined the impact of temperature over the lifetime of an animal are prohibitively expensive. At the same time environmental educators need guidance on the appropriate study systems to use with a balance between the species having an obvious response and ensuring the outcomes are ethical and sustainable. In our study, we created and tested a cost-effective experiment meant to be used for environmental education purposes. More specifically, we tested the sensitivity of the Painted lady butterfly Vanessa cardui to temperature variations using a homemade incubator. We describe the design of this experiment and report findings on survival rate, morphological variations, pupation time, and wingspan of adults across a range of biologically relevant temperatures. The information provided give educators options for testing a variety of hypotheses with regards to the impacts of temperature using an affordable and flexible set-up. Furthermore, the findings can be used by students to develop an understanding of the ramifications of the butterflies responses in an ecological context.

Authentic learning opportunities that simulate full scale design and construction experiences using real materials offer ideal experiential learning environments for construction and civil engineering students by challenging students to apply building concepts in practical settings. However, the excessive cost of real building materials required for this mode of education limits access to the vast majority of students. As a result, educational researchers have explored potential alternatives to provide cost-effective experiential learning through activities using mock-up materials (e.g., plastic straws, popsicle sticks) and simulation of experiences using immersive technologies (e.g., virtual reality or augmented reality). While some of these alternatives approximate the environment and others provide physical interaction with mock-up materials, the lack of authenticity in the building materials used introduces some apparent differences between the “authentic” learning environments and their cost-effective approximations. Therefore, this research aims to identify the learning processes reported by students and faculty who participated in authentic learning experiences to understand the ways in which this mode of education offers unique value to construction education. Their interview responses illustrated characteristics of authentic learning experiences that were believed to be critical to the learning process, some of which included: working in groups; interdisciplinary participants; and use of real construction materials. Although some of these characteristics are intrinsically linked to the use of real materials, others do not explicitly refer to interaction with real materials. This may indicate to aspects of the authentic learning processes that educational researchers can strategically target through more cost-effective learning environments like virtual and augmented reality. The contribution of this paper is in identifying the characteristics of authentic learning experiences that may guide educational investment and research innovations that aim to replicate some of these learning experiences through more accessible learning environments.

Microgrids can be used for securing power supply during network outages. Underground cabling of distribution networks is another effective, but conventional and expensive alternative to enhance reliability of power supply. This paper presents firstly an analysis method for the determination of microgrid power supply adequacy during islanded operation, and secondly, a comparison method for overall cost calculation of microgrids vs. underground cabling. The microgrid power adequacy during a rather long network outage is required in order to indicate high level of reliability of supply. The overall cost calculations consider the economic benefits and costs incurred combined for both the distribution network company and the consumer. Whereas the microgrid setup determines the islanded operation power adequacy and thus the reliability of supply, the economic feasibility results from the normal operations and services. The methods are illustrated by two typical, and even critical, case studies in rural distribution networks: an electric-heated detached house and a dairy farm. These case studies show that even in case of a single consumer, a microgrid option could be more economical than network renovation by underground cabling of a branch in order to increase reliability.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

With the advent of COVID19, the attitude of health authorities around the world, led mainly by the West, demanded a level of proof as evidence for cheap, non-patented remedies while promoting expensive, patented, and untested remedies by using emergency use authorization and special provisions afforded to the status of a pandemic emergency. Western science has neither a tested nor a valid historical basis of a logical system that informs to authenticate scientific practices. Here we use a logical heuristic derived from ancient Buddhist logic, which is consistent with the conduct of modern science. We applied the heuristic to show that enough evidence was available for using cost-effective early therapies such as vitamin D supplementation as a public health measure during the first half of 2020. Strong supporting evidence has since accumulated. Apart from political and financial decisions incompatible with science and other conflicts of interest, a critical barrier to evaluating and approving early therapies appears to be the fallacy that the randomized controlled trial (RCT) is the superior proof method in medical hypotheses, including those for nutrients. Logically, no reason exists why properly designed retrospective, ecological, and naturalistic studies with adequate sample sizes and applied appropriate statistical methods would not be as valid as RCTs, especially when elucidating a causative factor instead of treatment. That assertion is particularly true for nutrient deficiencies, interventions, and other cost-effective therapies. Leading health authorities’ failure or refusal to consider other study types (because of either poor logic or vested interest) probably contributed to the spread of misinformation, symptomatic disease, complications, and deaths from COVID19. Partial immunity derived from vaccines and the later development of more contagious variants—and thus a sense of acceptance that SARS-CoV-2 had progressed from a pandemic to an endemic—shows the hollowness of the initial promotions and mandates of vaccines as a cure. Adequate knowledge was available in 2020 to advise that SARS-CoV-2 will continue to mutate, with variants emerging a few times per year, making the vaccine less effective. Emerging evidence confirms that natural immunity better protects against new variants than vaccination against the spike protein. Had vitamin D been adopted as part of the public health measure through a broader supplementation program in 2020 or even today (through sun exposure or as a prophylactic or adjunct therapy early on), the viral spread and symptomatic disease may have been suppressed, with minimal lockdowns and quarantine, and economic harm. The pandemic could have been halted with a significantly reduced need for hospitalization, complications, and deaths, potentially saving millions of lives.

SmCo5 constitutes one of the strongest class of permanent magnets, which exhibit enormous uniaxial magnetocrystalline anisotropy energy and have a high Curie temperature. However, the performance of SmCo5 permanent magnets is hindered by a limited energy product and relatively high supply risk. Sm is a moderately expensive element among its group, and Co is a material more expensive than Fe, making SmCo5 magnets the most expensive class of permanent magnets. Subsequently, the need for new materials, with less content in critical and thus expensive resources, is obvious. A promising path of producing new compounds that meet these requirements is the chemically modification of established materials used in PM towards the reduction of expensive resources, for example reducing Co content with transition metals (like Fe, Ni) or using as substitutes raw rare earth materials with abundance greater than their demand, like Ce and La. Important instrument to achieve these goals are theoretical calculations, like Ab-initio methods, and especially DFT based calculations in predicting the possible stable RE-TM intermetallic compounds and their magnetic properties. This review aims to present the progress of recent years in the production of improved SmCo5 type magnets.

The first exposure to influenza is thought to impact subsequent immune responses later in life. The consequences of this can be seen during influenza epidemics and pandemics with differences in morbidity and mortality for different birth cohorts. There is a need for better understanding of how vaccine responses are affected by early exposures to influenza viruses. In this analysis of hemagglutination inhibition (HI) antibody responses in two cohorts of military personnel we noticed differences related to age, sex, prior vaccination, deployment and birth year. These data suggest that HI antibody production, in response to influenza vaccination, is affected by these factors. The magnitude of this antibody response is associated with, among other factors, the influenza strain that circulated following birth.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

Providing healthcare workers with cost information about the medications they prescribe can influence their decisions, particularly when that information is provided at the very moment they are faced with a prescribing decision. The current study aimed to analyse the impact of nudges that presented cost information to prescribers through their organisation's electronic prescribing system. The nudges were co-created by the research team (composed of behavioural scientists) and the lead hospital pharmacist. One nudge provided simple cost information (percentage difference between two brands of Mesalazine – Asacol and Octasa). The second nudge provided the potential annual cost-saving that could result if the cheaper medication was selected across the organisation. While the statistical analyses revealed that these nudges were not effective, several administrative barriers were overcome, which may inform future research. For example, presenting aggregated cost information to the prescribers is possible even when the actual cost of medicine is confidential and can not be displaced. In addition, future research could reveal more behavioural factors that facilitate medication optimisation.

To assure the opacity, an optimal problem is to retain the occurring events sequences as many as possible. Contrary to such problem, the other optimal problem is to preserve the minimal occurring events sequences. In the paper, based on the choosing cost, an optimal opacity-enforcing model is presented to minimize the sum of discount choosing cost, which is not only to preserve the opacity, but also to retain the secret to the maximum. To solve the model, two scenarios on opacity are considered. For the two scenarios, some algorithms are presented to achieve the optimal solution for the model by using the method of dynamic programming. And then, the solutions produced by the algorithms are proved correctly by theoretical proof. Finally, some illustrations for the algorithms are given.

Given the imperative of security, sustainability of supply, strategic considerations, and energy independence, there is a widely acknowledged need to persist in utilizing coal as the primary fuel for electricity generation in power plants. However, in order to combat the rising levels of CO2 in the atmosphere, it is crucial to advance the development of carbon capture and storage (CCS) technologies that enable fossil fuel power plants to achieve zero emissions. These technologies play a pivotal role in capturing and effectively storing CO2, thus ensuring that coal-based power generation can continue while significantly reducing its environmental impact. By implementing CCS solutions, fossil fuel power plants can transition towards a more sustainable and environmentally friendly energy future.The utilization of chemical solvents for CO2 absorption, coupled with long-term storage, presents an intriguing and commercially viable technology for CO2 capture. However, the significant energy demands of the solvent regeneration process necessitate optimization, particularly in large-scale power plants. While the current cost of CO2 capture stands at approximately #55,000.00(Naira) per ton of CO2, the objective is to reduce this cost to below #25,000.00(Naira) per ton of CO2. This reduction in cost is essential to ensure the economic feasibility and widespread adoption of CO2 capture technologies in power generation.This research paper explores various approaches to address the energy demands associated with amine scrubbing integration in a commercial power plant. It provides a comprehensive analysis, both technically and economically, of the performance of these different approaches. While some of the proposed schemes may result in minor efficiency reductions, the key objective is to calculate the specific cost per ton of CO2 captured. The primary focus is on identifying the most suitable configuration to implement large-scale, cost-effective schemes that can serve as a foundation for CO2 capture demonstration projects. By determining the optimal configuration, this research aims to pave the way for the successful implementation of efficient and economically viable CO2 capture technologies in the power generation sector.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Preparation of a low-cost cellulose-based bioadsorbent from the cellulosic material extracted from the rose stems (CRS) was carried out; rose stems were considered agricultural wastes. After the required pretreatment of this waste, and its further treatment with an acidic mixture of acetic and nitric acids, the CRS product was yielded. The resulting bioadsorbent was characterized by several techniques, such as X-ray diffraction, which revealed diffraction maxima related to cellulose structure, whose calculated crystallinity index (CrI) was 75 %. In addition, Fourier Transform Infrared spectroscopy (FTIR), 13C Nuclear Magnetic Resonance (NMR), and X-ray Photoelectron Spectroscopy (XPS) showed signs of acetylation of the sample, also, the thermal properties of the solid was evaluated through Thermogravimetric Analysis (TGA). Scanning Electron Microscopy (SEM) showed cellulose fibers before and after the adsorption process, some particles with not regular shapes were also observed. The CRS bioadsorbent was used in the effective adsorption of valuable Tb(III) from aqueous solution. The adsorption data resulted in a better fit to the Freundlich isotherm, and pseudo-second-order kinetic models; however, chemisorption had not been ruled out. Finally, desorption experiments revealed a recovery of terbium ions with an efficiency of 97 % from terbium-loaded bioadsorbent.

The current treatment for cervico-facial cancer involves radio and/or chemotherapy. Unfortunately, cancer therapies can lead to local and systemic complications such as mucositis, which is the most common dose-dependent complication in the oral cavity and gastrointestinal tract. Mucositis can cause a considerably reduced quality of life in cancer patients already suffering from physical and psychological exhaustion. However, melatonin, whose role in the treatment of mucositis has recently been investigated, offers an effective alternative therapy in the prevention and/or management of radio and/or chemotherapy-induced mucositis. This review focuses on the pathobiology and management of mucositis in order to improve the quality of cancer patients’ lives.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

Tungiasis is a neglected tropical disease caused by skin-penetrating female Tunga penetrans fleas. Although tungiasis causes severe health problems, its ecology is poorly understood and morphological descriptions of larvae are unavailable. To identify T. penetrans immature stages and sites where they develop, diagnostic PCRs are required. However, flea larvae feed on soil organic matter rich in PCR inhibitors. Here, three DNA preparation methods, a soil DNA kit removing inhibitors, a simple ammonium acetate precipitation approach (AmAcet) and a crude lysate of larvae (CL), were combined with amplification by the highly processive FIREPol® Taq or the inhibitor-resistant Phusion® polymerase. Independent of the polymerase used, frequency of successful amplification, Cq values and PCR efficacies for the low-cost CL and AmAcet methods were superior to the commercial kit for amplification of a 278 bp partial internal transcribed spacer-2 (ITS-2) and a 730 bp pan-Siphonaptera cytochrome oxidase I PCR. For the CL method combined with Phusion® polymerase, costs were approximately 20-fold lower than for methods based on the soil DNA kit, which is a considerable advantage in resource-poor settings. The ITS-2 PCR did not amplify Ctenocephalides felis genomic or Tunga trimammilata ITS-2 plasmid DNA allowing it to be used to specifically identify T. penetrans.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

The search for sustainable resources remains a subject of global interest and the conversion of the abundantly available bivalve shell wastes to advanced materials is an intriguing method. By grinding, each shell of bivalves (cockle, mussel, and oyster) was transformed to the same crystal type of calcite phase of CaCO3, revealed by FTIR and XRD results. Each individual shell powder was reacted with H3PO4 and H2O to prepare Ca(H2PO4)2•H2O giving an anorthic crystal structure. The mixture of each shell powder and its produced Ca(H2PO4)2•H2O was heated at 900 °C for 3 h, giving rhombohedral crystal -Ca3(PO4)2 powder. FTIR and XRD results of the CaCO3, Ca(H2PO4)2•H2O, and Ca3(PO4)2 prepared from each shell powder are quite similar showing no impurities. Thermal behaviors of CaCO3 and Ca(H2PO4)2•H2O produced from each shell are slightly different. Particle sizes and morphologies of all products are significantly different, affected by the kind of shells used. Overall, the bivalve shell wastes were successfully converted to CaCO3, Ca(H2PO4)2•H2O, and Ca3(PO4)2 by a simple, rapid, environmentally benign, and cost-effective approach, which can be a huge potential in many industries providing both economic and ecological benefits according to the Bio-Circular-Green Economy (BCG) model.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

Background: Liquid biopsy is widely recognised as an efficient diagnostic method in oncology for disease detection and monitoring. Though examination of circulating tumor cell (CTC) is mostly implemented for assessment of genomic aberrations, need of complex methodologies for their detection has impeded its acceptance in low resource settings. We evaluated the cell free DNA (cfDNA) as a liquid biopsy tool and investigated its utility in breast cancer patients. Methods: Total cell free DNA was extracted from plasma of breast cancer patients (n=167) with median follow up of more than 5 years, at various stages of the disease. Quantitative PCR was performed to estimate the copy numbers of two fractions of ALU repetitive elements (ALU 115 and ALU 247) and DNA Integrity (DI) was calculated as the ratio of ALU 247/115. Mutations in TP53 and PIK3CA in the cfDNA was estimated by next-gen sequencing (NGS) in a subset of samples. Association of the levels of both the ALU fragments with various clinico-pathological factors and disease-free survival at various stages were examined. Nomogram models were constructed with clinical variables and ALU 247 levels to predict disease-free survival and best performing model was evaluated by decision curve analysis. Results: DI and ALU 247 levels were significantly lower (p<0.0001) in the post-operative plasma when compared to their pre-surgery levels. DI and ALU 247 were found to be significantly higher in patients with metastasis (p<0.05). Patients with higher levels of ALU 247 in their post-operative plasma had significantly poor disease-free survival (p=0.005). Higher level of ALU 247 in circulation also correlated with low tumor-infiltrating lymphocytes (TIL) within their primary tumors in the ER-negative breast cancer subtype (p=0.01). Cox proportional hazard analysis confirmed ALU 247 as an independent variable of disease-free survival both in univariate and multivariate analysis [HR 1.3 (95% CI 1.047 to 1.613, p= 0.017)]. Nomogram model showed addition of ALU 247 with other variables significantly improved (C-index-0.823) the predictive ability of the model. Conclusion: Our results confirm the utility of cfDNA as an evolving liquid biopsy tool for molecular analysis. Evaluation of larger fragment of cfDNA estimated through ALU 247 can provide vital information concurrent with the pathological process of disease evolution in breast cancer and warrants expansion to other cancer types.

This study demonstrated that antibiotic residue in milk can be reduced when dairy farmers use Ethno-veterinary Practices (EVP) based on herbal alternatives to prevent and cure common clinical conditions in cattle instead of antibiotics. Of the 220 farmers selected for the study, 140 were trained and motivated to use validated herbal formulations, 80 were kept as control. Milk samples from the selected farmers (except Thirukanurpatti milk society) tested positive for antibiotic residue in the baseline survey. One year after interventions, the milk from 123 (87.86%) farmers out of 140, were without any detectable antibiotic residue, while samples from 11 farmers (7.85%) were low positive for either Beta-lactams or sulphonamides and 6 (4.29%) were positive for Beta lactams and/or sulphonamides. These 17 (11 + 6) farmers had used antibiotics along with herbal formulations. The milk samples from the control groups were positive for beta lactam and sulphonamide. There was suggestive significance of change in knowledge, attitude and practice of EVP among the farmers from Kerala and Tamil Nadu. A progressive reduction in the incidence of mastitis, enteritis, repeat breeding and cowpox were observed from 2016 to 2019 among the cows treated with EVP. Use of herbal alternative also resulted in a significant reduction in health care expenditure of cattle.

The Imbalance Cost Pass-Through (ICPT) is a flexible component of the Incentive Regulation (IBR) that empowers power producers to adjust tariffs in response to variable fuel prices, thereby enhancing the economic resilience of electricity generation. However, the cost of electricity generation is significantly influenced by the volatility of commodity prices, including coal, gas and LNG. In Malaysia, the Energy Commission has conducted biannual reviews of fuel and other generation costs. Any cost savings or increases identified during these reviews will be passed on to customers in the form of rebates or surcharges. Due to that reason, this study proposes ICPT price forecasting for the electricity market in Peninsular Malaysia. The study aims to construct an ICPT-related baseline model for the peninsular generation data by employing three forecasting methods. The forecasting performance is analysed by a Mean Absolute Percentage Error (MAPE). In findings, the ARIMA method is one of the most accurate forecasting methods for fuel prices compared to the Moving Average (MA) and LSSVM methods. The observed price differences between the ARIMA and LSSVM models for ICPT are minimal. The ICPT price for July-December 2022 and January-June 2023 is MYR 0.21/ kWh for ARIMA and MYR 0.18/kWh for LSSVM, which are close to the actual TNB’s ICPT tariff. As for the forecasting, the ICPT price is expected to drop for the next announcement. The findings of this study may contribute to a positive impact on the sustainability of the energy sector in Malaysia.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

The proof-of-principle demonstration of a simple, yet effective method of autocorrelation artifact removal for optical coherence tomography (OCT) is presented using a custom-designed parallel spectral-domain OCT (SD-OCT) instrument. Our real-time method is based on time-averaged sampling of a sinusoidal phase modulation in the reference arm. Unlike other existing methods, our technique can completely eliminate arbitrarily located, arbitrarily strong autocorrelation artifacts.

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

Emulsion stabilisation of base layers surfaced with chip seals often proves problematic with chips punching into the base and early distress. This can be aggravated by the use of modified binders that restricts the evaporation of moisture from pavement layers. The introduction of New-age (Nano) Modified Emulsion (NME) stabilisation has the advantage that water is chemically repelled from the stabilised layer resulting in an accelerated development of strength. A need was identified to evaluate the early life performance of selected chip seals, together with identified binders. Three different chip seal surfacings with unconventional modified binders were constructed and evaluated using Accelerated Pavement Testing (APT) with the MMLS3. The objectives of the experimental design and testing were to evaluate binder performance, early loss of chips before chip orientation at low temperatures, punching of the chips into the NME stabilised base, deformation characteristics of a Cape seal and the effect of the use of a standard normal modified binder. This paper contains details of the NME base layer, the binder and seal selection and the test results. It is shown that a cost-effective thin chip seal in combination with a suitable binder can be used on a NME stabilised base with confidence.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P&lt;0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Evidence suggests that COVID-19 infection can cause lasting health consequences. Multidiscipli-nary rehabilitation services have been recommended to reduce the sequalae. However, the effec-tiveness of physical exercise interventions remains insufficiently documented. The aim of this study was to develop and implement a specific and well tolerated protocol-based, intervention to reduce muscle weakness in older adults impacted by COVID-19. Forty six older adults random-ized into Intervention and Control Groups. Isometric and isokinetic strength assessments were conducted for selected muscle groups using JBA Staniak® torquemeter and Biodex System 3 dy-namometer. Functional abilities were evaluated with the Time Up and Go test and Chair Stand Tests. Men in intervention group demonstrated a significant improvement in static conditions for knee flexors (KF), trunk extensors (TE) and trunk flexors (TF) and in dynamic conditions for knee extensors (KE). Women in intervention group showed significant improvement in static condition for EF, KF, TE and TF and in dynamic for a KE and for a KF. The interaction GROUP x TESTING SESSION was significant for Chair test (s) and Chair test (n). Our results demonstrate the effec-tiveness of a well-tolerated, protocol-based approach that can be used to diminish long lasting functional deficits in post-covid survivors.

Unmanned aerial vehicles (UAVs), commonly known as drones, present a cost-effective solution for the swift collection of data from vast and remote areas that are otherwise difficult to access. The Mediterranean Basin, known for being a hot spot for plant biodiversity, hosts several habitats and taxa of significant naturalistic value. However, many of these areas are often inaccessible to botanists, making exploration and research challenging. The aim of this paper is to involve the utilization of drone surveys and open-source software for botanical research. Our primary goal is to show the effectiveness of these tools in the field and demonstrate their practical application in Natura 2000 sites. The protected area chosen for this research is Rocca di Novara, situated in northeastern Sicily. Thanks to our drone investigations, we were able to capture images of the mountain’s side that is inaccessible to humans. This allowed us to observe the habitat of some species in detail. One of the most fascinating discoveries was the reappearance of Saxifraga callosa subsp. australis, which had not been confirmed in this area for over 140 years. Using drones for botanical research can boost field research, making monitoring easier and more cost-effective over time, especially in Natura 2000 sites.

One of the main constraints of agriculture in sub-Saharan Africa is the steady decline in the level of soil fertility resulting in a continuous decline in crop yields. This study assessed the impact of grass mulch on: the productivity, the income, the soil carbon, and the phytodiversity within three pineapple-based systems of the ecovillage of Donomade in Togo. They are: a model farm with mulch, adopters’ farms, and non-adopters. Production-related data (e.g., number of plants, the number of productive individuals, the mass of products harvested) was obtained by a sampling an area of 100 m². These measurements were coupled with a semi-structured individual’s interviews of producers on the history of the plots and production costs in order to assess their profitability. The fruit production was three times higher within the adopters’ plots (21240 ± 11890 kg/ha) than the non-adopters (7840 ± 7890 kg/ha) and the two thirds of the model farm (33838 ± 9460 kg/ha). Consequently, the net income was 8 to 11 times higher than the conventional pineapple cropping system. According to the cropping systems, the total soil carbon was higher within mulching plots including the model farm and the adopters’ plots and lower within the non-adopters’ plots.

The accumulation of high levels of lead or lead ions in a human body is harmful, particularly to children. Its neurotoxic effect is profound, damaging the central and peripheral nervous systems, resulting in stunted growth, behavioral problems and learning disabilities. The major source of lead or lead ions comes from the drinking water and tap water. The assessment of the water quality, including lead or lead ion content, is usually completed by a regional water department professional. This assessment is time-consuming and requires expensive instruments and skilled operators. Therefore, there is a need to produce a simple-use and relatively inexpensive method to detect lead or lead ions in water samples. This research has developed a simple-use, cost effective sensor system for the detection of lead ions in tap water. An under-potential deposited bismuth sub-layer on a thin gold film based electrochemical sensor was designed, manufactured and evaluated. Differential pulse voltammetry (DPV) measurement technique was employed in this detection. Tap water from the Cleveland, Ohio, USA regional water district was the test medium. Concentrations of lead ion in the range of 8 X 10^-8 M to 8 x 10^-4 M were evaluated. This DPV detection system required 3 -6 minutes to complete the detection measurement. A longer measurement time of 6 minutes was used for the lower lead ion concentration. The selectivity of this lead ion sensor was very good, and Fe III, Cu II, Ni II and Mg II at a concentration level of 5×10^-4 M did not interfere with the lead ion measurement.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

The detection and quantification of protein–protein interactions (PPIs) is a crucial technique that often involves the use of recombinant proteins with fusion-protein tags, such as maltose-binding protein (MBP) and glutathione-S-transferase (GST). In this study, we improved the cohesive and sticky properties of gelatinized starch by supplementing it with agarose, resulting in a harder gel that could coat the bottom of a microtiter plate. The resulting gelatinized starch/agarose mixture allowed for the efficient immobilization of MBP-tagged proteins on the coated plates, enabling the use of indirect ELISA-like PPI assays. By using the enzymatic activity of GST as an indicator, we succeeded in determining the dissociation constants between MBP-tagged and GST-tagged proteins on 96-well microtiter plates and a microplate reader without any expensive specialized equipment.

SARS-CoV 2 also known as COVID-19 is a fast spreading coronavirus related disease that emerged from China in December 2019 and is currently attained the status of a pandemic. There are currently no drugs/ vaccines against the same and moreover limited diagnostic tests to identify the infection. Additionally, these tests are expensive and hence are exclusive for very highly suspected cases of the disease especially in developing countries. This is causing an under-diagnosis which is an alarming state of affairs, as even a single missed SARS-CoV 2 case would spread the disease exponentially and keep it in the community. Through this entirely in silico study, we have developed a cheaper and faster diagnostic method based on simple PCR and restriction enzyme digestion, commonly used in restriction fragment length polymorphism (RFLP) tests. Through comparative genomics, we found the closest neighbours of SARS-CoV 2 then found the highly conserved regions of the genome which were absent in SARS-CoV 1, its closest neighbour. Then we found restriction sites for various enzymes followed by designing of PCR primers flanking those sites. We have found the primer pair to produce a 401 bp amplicon and when digested by SwaI enzyme, it produces two fragments of lengths 216 bp and 185 bp. As an internal control, GAPDH primers are pooled with the SARS-CoV 2 primers as the patient sample will also include human RNA mixed with the viral RNA. This primer pair gives an amplicon of 131 bp and hence a negative sample should show a single band of 131 bp while a positive digested sample will give three bands of 401 bp, 216 bp and 131 bp. The primers are specific to SARS-CoV 2 only and can additionally be used for SYBR green based real time quantification of viral load. The developed tests have not yet been tested in vitro due to stressed out working hours in the only pathogenic virus handling laboratory in our institute. Nonetheless, this study works as a head start for other laboratories to rapidly test the suggested protocols in vitro and make available a cheaper alternative test for SARS-CoV 2 which would especially be beneficial for the lower to middle income countries.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

A simple in vitro biosensor for the detection of β-amyloid 42 in phosphate-buffer saline (PBS) and undiluted human serum was fabricated and tested based on our platform sensor technology. The bio-recognition mechanism of this biosensor was based on the effect of the interaction between antibody and antigen of β-amyloid 42 to the redox couple probe of K₄Fe (CN) ₆ and K₃Fe (CN) ₆. Differential pulse voltammetry (DPV) served as the transduction mechanism measuring the current output derived from the redox coupling reaction. The biosensor was a three-electrode electrochemical system, and the working and counter electrodes were 50 nm thin gold film deposited by sputtering technique. The reference electrode was a thick-film printed Ag/AgCl electrode. Laser ablation technique was used to define the size and structure of the biosensor. Cost-effective roll-to-roll manufacturing process was employed in the fabrication of the biosensor making it simple and relatively inexpensive. Self-assembled monolayers (SAM) of 3-Mercaptopropionic acid (MPA) was employed to covalently immobilize the thiol group on the gold working electrode. A carbodiimide conjugation approach using N-(3-dimethylaminopropyl)-N’-ethylcarbodiimide hydrochloride (EDC) and N–hydroxysuccinimide (NHS) was undertaken for cross-linking antibody of β-amyloid 42 to the carboxylic groups on one end of the MPA. The antibody concentration of β-amyloid 42 used was 18.75µg/mL. The concentration range of β-amyloid 42 in this study was from 0.0675µg/mL to 0.5µg/mL for both PBS and undiluted human serum. DPV measurements showed excellent response in this antigen concentration range. Interference study of this biosensor was carried out in the presence of Tau protein antigen. Excellent specificity of this β-amyloid 42 biosensor was demonstrated without interference by other species such as T-tau protein.

SARS-CoV-2 was identified as the pathogenic agent causing the COVID-19 pandemic. Among the proteins codified by this virus, the Spike is one of the most external and exposed. A fragment of the Spike protein, named the Receptor Binding Protein (RBD) interacts with the ACE2 receptors of human cells, allowing the entrance of the viruses. RBD has been proposed as an interesting protein for the development of diagnosis tools, treatment and prevention of the disease. In this work, a method for recombinant RBD production using Pichia pastoris as a cell factory in a Stirred Tank Bioreactor (SRTB) up to 7 L was developed. Using a basal saline medium with glycerol, methanol and compressed air in a four stages procedure, around 500 mg/L of raw yRBD (RBD produced by yeasts) and 206 mg/L of purified (>95%) RBD were obtained. Thereby, the proposed method represents a feasible, simple, scalable and cheap procedure for the obtention of RBD for diagnosis kits and vaccines formulation

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Many mathematical models of strategic play or better choice overlook adjustment costs. Rather often, the modeler's concern is just with improvement of objectives. This optic doesn't quite fit agents somewhat attached to status quo. They reason whether moving to another state be worth their while. For that, the realized gains must outweigh the inconveniences of the move. This note offers some observations on the fact that change usually entails cost.

The effects on Raychaudhuri's equation of an intrinsically discrete or particle nature of spacetime are investigated, through consideration of null congruences emerging from, or converging to, a generic point of spacetime, i.e. in geometric circumstances somehow prototypical of singularity issues. This is done from an effective point of view, meaning through a (continuous) description of spacetime modified to embody the existence of an intrinsic discreteness on the small scale, adding to previous results for non-null congruences. Various expressions for the effective rate of change of expansion are derived. They in particular provide finite values for the limiting effective expansion and its rate of variation when approaching the focal point; this on top of resulting non vanishing the limiting cross-sectional area itself of the congruence.

Nonparametric assessments of police technical and scale efficiency is challenging because of the stochastic nature of criminal behavior and because of the subjective dependence on multiple decision criteria, which can lead to a more or less efficiency prospect depending on the regulation, necessity, or organizational objective. There is a trade-off between efficiency and effectiveness in many police performance assessments, i.e., efficient departments (producing more clear-ups with a given resource) are crime-specialized or cannot reproduce those good results effectively on more severe or complex occurrences. This study proposes a combined methodology for carrying out efficiency and effectiveness analysis of Police departments. A conditional non-parametric approach, which allows to include crime as an external factor in the analysis, is combined with a non-compensatory ranking based on the PROMETHEE II methodology for the approach illustrated on the multidimensional efficiency and effectiveness comparison of 145 Pernambuco (Brazil)'s police departments. The application results offer compelling perspectives for public administrations concerning the strategic prioritization of units for rewards or interventions.

The pollution of the bays in Abidjan is a major concern for the Ivorian policy makers. In fact, the pollution of the bays induce high costs to the society while impacting population health dramatically. As a result, pollution reduction management of production activities has been undertaken in the Cocody Bay area. To our knowledge, no study has yet proposed a model to evaluate the cost-effectiveness of these pollution management strategies. A cost-effectiveness model, based on Monte Carlo simulation, was developed to assess the economic and environmental impacts of various scenarios characterized by a set of production practices, both in the short term and in the long term. The authors discuss the steps and input parameters of the model presented. The proposed model may serve as the basis for identifying an optimal production scenario defined as the scenario with the best incremental cost-effectiveness ratio considering a willingness to pay (WTP) threshold. The WTP, to be estimated based on the gross domestic product of Côte d’Ivoire, represents the opportunity costs associated with selecting the optimal scenario. The current framework can also be applied to other settings facing similar challenge.

This paper present a platform for airborne sensor applications using low-cost, open-source components carried by an easy-to-fly unmanned aircraft vehicle (UAV). The system, available in open-source [1], is designed for researchers, students and makers for a broad range of their exploration and data-collection needs. The main contribution is the extensible architecture for modularized airborne sensor deployment and real-time data visualisation. Our open-source Android application provides data collection, flight path definition and map tools. Total cost of the system is below 800 dollars. The flexibility of the system are illustrated by mapping the location of Bluetooth beacons (iBeacons) on a ground field and by measuring water temperatures in a lake.

By using geodesic equations to obtain a gravitational potential generated from a point-like source, we end up in the concept of a nearly Newtonian gravity to analyse effective potentials of quasi-circular orbits. By means of an approximate solution from an axially static and symmetric Weyl metric, we study an effective gravitational potential to obtain its related rotation curves, orbital planes and orbits. Moreover, using as initial condition a Plummer sphere, some prospects on star cluster disruption are also discussed in this framework.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

Distributed tracing is a cutting-edge technology for monitoring, managing, and troubleshooting native cloud applications. It offers a more comprehensive and continuous observability, surpassing traditional logging methods, and is indispensable for navigating modern complex software architectures. However, the sheer volume of generated traces is staggering in distributed applications, and direct storage and utilization of every trace are impractical due to associated operational costs. This entails a sampling strategy to select which traces warrant storage and analysis. Historically, sampling methods have included a rate-based approach, often relying heavily on a manual configuration. There is a need for a more intelligent approach, and we propose a hierarchical sampling methodology to address multiple requirements concurrently. Initial rate-based sampling mitigates the overwhelming volume of traces, as no further analysis can be performed on this level. In the next stage, more nuanced analysis is facilitated based on the previous foundation, incorporating information regarding trace properties and ensuring the preservation of vital process details even under extreme conditions. This comprehensive approach not only aids in the visualization and conceptualization of applications but also enables more targeted analysis in later stages. As we delve deeper into the sampling hierarchy, the technique becomes tailored to specific purposes, such as simplifying application troubleshooting. In this context, the sampling strategy prioritizes the retention of erroneous traces from dominant processes, thus facilitating the identification and resolution of underlying issues. The focus of this paper is to reveal the impact of the sampling on troubleshooting efficiency. Leveraging intelligent and explainable artificial intelligence solutions enables the detection of malfunctioning microservices and provides transparent insights into root causes. We advocate for using rule-induction systems, which offer explainability and efficacy in decision-making processes. By integrating advanced sampling techniques with machine learning-driven intelligence, we empower organizations to navigate the complexities of large-scale distributed cloud environments effectively.

We report the negative effective mass metamaterials based on the electro-mechanical coupling exploiting plasma oscillations of a free electron gas. The negative mass appears as a result of vibration of a metallic particle with a frequency of ω which is close the frequency of the plasma oscillations of the electron gas m_2 relatively to the ionic lattice m_1. The plasma oscillations are represented with the elastic spring k_2=ω_p^2 m_2, where ω_p is the plasma frequency. Thus, the metallic particle vibrated with the external frequency ω is described by the effective mass m_eff=m_1+(m_2 ω_p^2)/(ω_p^2-ω^2 ) , which is negative when the frequency ω approaches ω_p from above. The idea is exemplified with two conducting metals, namely Au and Li.

We use oblate coordinates to study its resulting orbit equations. Their related solutions of Einstein's vacuum equations can be written as a linear combination of Legendre polynomials of positive de nite integers $l$. Starting from solutions of the zeroth order $l=0$ in a nearly newtonian regime, we obtain a non-trivial formula favoring both retrograde and advanced solutions for the apsidal precession depending on parameters related to the metric coecients, particularly applied to the apsidal precessions of Mercury and asteroids (Icarus and 2 Pallas). As a realization of the equivalence problem in general Relativity, a comparison is made with the resulting perihelion shift produced by Weyl cylindric coordinates and the Schwarzschild solution analyzing how different geometries of space-time influence on solutions in astrophysical phenomena.

The global trend towards increased demand for organic food, greener environments, and the integration of biological control agents into pest management strategies has greatly enhanced the need for biological pesticides (biopesticides). Biopesticides are generally environmentally friendly and are made from micro-organisms or other natural substances. Despite their great potential, relatively few have been registered and commercialised in Nigeria compared to other African countries such as South Africa and Kenya. Biological active agents are so diverse such that ap-plying the same safety standards or environmental conditions to all of them is almost impossible. A review of risk assessment processes and comparative assessments of Nigeria's biopesticide regulations with other developing African countries and developed regions was conducted. Prolonged field testing, lack of bridged risk assessments and technical checklists have been identified as key factors hampering the timely development and commercialisation of biopesti-cides in Nigeria. Recommendations on necessary changes to the existing Nigeria biopesticide regulations have been made. Risk assessment matrices for microbial and biochemical biopesti-cides and a scientific/technical checklist have also been developed. Harmonisation and data ex-change among other countries in the region will also enhance the advancement of scientific and technical knowledge for sustainable regulation and cross-border trade.

Mosquitoes carrying endosymbiotic bacteria called Wolbachia are being released in mosquito and arbovirus control programs around the world. Open field releases of Wolbachia-infected male mosquitoes have achieved over 95% population suppression, while the replacement of populations with Wolbachia-infected females is self-sustaining and can greatly reduce local dengue transmission. Despite many successful interventions, significant questions and challenges lie ahead. Wolbachia, viruses and their mosquito hosts can evolve, leading to uncertainty around the long-term effectiveness of a given Wolbachia strain, while few ecological impacts of Wolbachia releases have been explored. Wolbachia strains are diverse and the choice of strain to release should be made carefully, taking environmental conditions and the release objective into account. Mosquito quality control, thoughtful community awareness programs and long-term monitoring of populations are essential for all types of Wolbachia intervention. Releases of Wolbachia-infected mosquitoes show great promise, but existing control measures remain an important way to reduce the burden of mosquito-borne disease.

We review past and present results on the non-local form-factors of the effective action of semiclassical gravity in two and four dimensions computed by means of a covariant expansion of the heat kernel up to the second order in the curvatures. We discuss the importance of these form-factors in the construction of mass-dependent beta functions for the Newton's constant and the other gravitational couplings.

Thailand has formulated her climate change policy and updated relevant plans and policies to align with the goal of achieving carbon neutrality and net zero GHG emissions. This study investigates the optimal level of GHG mitigation in Thailand, taking into account the marginal abatement cost (MAC) and social cost of carbon (SCC). It evaluates how energy efficiency and renewable energy technologies influence GHG reduction in the power and industrial sector and illustrates policy recommendations that align with the 2020 to 2050 policy and plan period. The findings indicate that there may be instances where GHG mitigation potential is insufficient to reach the national mile-stone. In such cases, it becomes imperative to leverage all technologies within the marginal abatement cost curve (MACC) and also utilization of the social cost of carbon for policy decision making and meeting the desired goals. In certain scenarios, the adoption of additional technologies or measures may be necessary, such as flexible power generation and deploying carbon capture and storage or hydrogen which are high-cost technologies. Furthermore, preparations should be made for multiple levels of climate change policies and plans beyond 2030.

The calculation of effective doses is crucial in many medical and radiation fields, in order to ensure safety and compliance with regulatory limits. Traditionally, Monte Carlo codes using detailed human body computational phantoms have been used for such calculations. Monte Carlo dose calculations can be time-consuming and require expertise in different processes when building the computational phantom and dose calculations. This study employs various machine learning (ML) algorithms to predict the organ doses and effective dose conversion coefficients (DCCs) for different anthropomorphic phantoms. A comprehensive data set comprising neutron energy bins, organ labels, masses, and densities is compiled from Monte Carlo studies, and is used to train and evaluate the supervised ML models. This study includes a broad range of phantoms, including those from the International Commission of Radiation Protection (ICRP-110, ICRP-116 phantom), the Visible-Human Project (VIP-man phantom), and the Medical Internal Radiation Dose Committee (MIRD-Phantom), with row data prepared using numerical data and organ categorical labeled data. Extreme gradient boosting (XGB), gradient boosting (GB), and the random forest-based Extra Trees regressor are employed to assess the performance of the ML models against published ICRP neutron DCC values using the mean square error, mean absolute error, and R² metrics. The results demonstrate that the ML predictions significantly vary in lower energy ranges and vary less in higher neutron energy ranges, while showing good agreement with ICRP values at mid-range energies. Moreover, the categorical data models align closely with the reference doses, suggesting the potential of ML in predicting effective doses for custom phantoms based on regional populations, such as the Saudi voxel-based model. This study paves the way for efficient dose prediction using ML, particularly in scenarios requiring rapid results without extensive computational resources or expertise. The findings also indicate potential improvements in data representation and the inclusion of larger data sets to refine model accuracy and prevent overfitting. Thus, ML methods can serve as valuable techniques for the continued development of personalized dosimetry.

This study investigates effective strategies for second language education in primary schools, analyzing the efficacy of immersive and interactive methods, digital literacy tools, and mixed-method approaches. The findings reveal significant improvements in language proficiency and student engagement through these methodologies, with immersive and interactive strategies showing substantial benefits in oral proficiency and engagement, digital tools enhancing accessibility and engagement, and mixed-method approaches yielding the highest overall effectiveness. The study underscores the importance of a balanced, flexible approach to language education, integrating traditional and modern methods to cater to diverse learner needs. These strategies not only advance linguistic skills but also contribute to the broader cognitive and emotional development of young learners, emphasizing the critical role of effective language education in preparing students for a globalized world.

Fractals and multifractals are well-known trademarks of nonlinear dynamics and classical chaos. The goal of this work is to tentatively uncover the unforeseen path from multifractals and selfsimilarity to the framework of effective field theory (EFT). An intriguing finding is that the partition function of multifractal geometry includes a signature analogous to that of gravitational interaction. Our results also suggest that multifractal geometry may offer insights into the non-renormalizable interactions presumed to develop beyond the Standard Model scale.

Why animals sleep is an outstanding open question. Information about the toxic byproducts of aerobic cellular respiration along with the analysis of patterns in animal size, sleep needs, dietary-type, metabolism, number of heart beats, transportation-network design, and transportation energetics/dynamics suggest that the function of sleep is to maximize the time an animal has to perform its life functions given the finite and constant number of lifetime heart beats it has. Sleep slows down metabolism, and the heart rate, thereby decreasing the load of toxic reactive oxygen species in the cell and extending the cell’s lifetime/proper-functioning. I argue that this is used to maximize the time an animal spends in its ‘effective environment’, which is defined as the period in the light cycle (day or night) where the essential life-functions of that animal (like finding resources, finding sex, hunting) are better achieved. Larger, slow-metabolizing animals need less sleep because their large-bodily-networks and slow metabolisms keep their heart rates relatively low, resulting in a lower rate of oxidative damage, and more relative time in the ‘effective environment’ to get their essential life-functions accomplished.

In this paper we have discussed the importance of human resource management in project management. As a concept human resource management emerged in 1980 [9]. It is very important to utilize resources effectively in any organization. Like triple constrains (cost, quality, scope) human resources are also considered as one of the most important factor for the success of any project. Management of human resources involve hiring experienced workers, giving appropriate training, acknowledgement about the significance of the project and the effective use of techniques and tools in order to get the project done productively with in time and budget. It becomes the responsibility of the project manager to effectively manage human resources as it is more challenging than managing other technical resources. In this paper we have also discussed the challenges that an organization faced during the management of the resources and use of some strategic human practices in order to overcome these challenges.

Intelligent ship technology is currently an international research hotspot, and model predictive control is widely used in the path-tracking control of intelligent vehicles. To construct an intelligent ship anti-disturbance path-tracking control method, firstly, an environmental disturbance model was constructed with the actual meteorological data of the target sea area. Secondly, the Fossen ship equation of motion is linearized and discretized as the ship motion model. Thirdly, the expression of the prediction equation is derived from the ship motion model. Fourthly, the cost function is constructed by using the polar diameter and polar angle values of the ship. Fifth, the power function in the cost function is replaced with an exponential function to obtain an improved cost function. Sixthly, according to the Lyapunov theory and the MPC terminal constraint theory, the stability of the improved cost function is verified. Seventh, different test paths are set up, the environmental disturbance model is taken as the external disturbance, the ship motion model, the prediction equation, and the improved cost function are used to design the anti-disturbance path-tracking control algorithm according to the model prediction control idea for simulation experiments. Finally, different MATLAB simulation results show that the improved cost function can resist disturbance of the external wave, current, and wind, and effectively track the target path. Therefore, this study provides a reference for improving the navigation safety of ship path-tracking.

Purpose: The ongoing COVID-19 crisis has created the need for social distancing between medical staff and patients, therefore, healthcare robotics is increasingly important as regards infectious control. The purpose of this study was to design and fabricate a remote controlled transport robot that could provide an optimum technology base for developing countries, having dual functions of telepresence and delivery operations inside or outside buildings, is easy to assemble and also easily able to be cleaned using standard chemical agents.Methods: This machine was designed and fabricated to incorporate two main functions; delivery and telepresence. The robot consists of a base frame, DC motors for driving and steering systems, actuator motor for driving wheel elevation, Wi-Fi AP/Repeater, network camera, and a necessary a back-up power system.Results: This robot can be used both indoors and outdoors. It can carry loads of more than 80 kg. The machine can cross obstacles greater than 3 cm. It can be cleaned by disinfectant agents. An actuator motor can lift the driving wheels above the surface to prevent gear damage. Conclusion: This article demonstrates the concept of a healthcare telepresence and delivery robot that can provide distancing during the present COVID-19 crisis, using optimum technology for low and middle-income countries. In the future, the researcher should consider development of the delivery controls, combined with the telepresence system using the internet of things, to improve the navigation system, the manipulator system for supporting multi-floor transportation, and also other multi-functional purposes.

The implementation of green logistics can reduce the increasingly serious environmental damage and improve the operating efficiency of logistics enterprises. In this paper, through quantitative calculation of logistics negative external costs, including traffic accidents, atmospheric pollution, noise pollution, and pollution caused by packaging, we build accounting standards to calculate the negative external cost of logistics enterprises that mainly generate pollution from transportation and packaging. Then, assuming the impetus provided by government implementing incentive mechanisms in a free market economy, we establish a ‘Logistics Negative External Cost Internalizing’ model, which quantitatively analyzes the relationships among freight rate, freight volume, investment of enterprise for implementing green logistics, and the subsidy given by government, under the comparison of the two modes ‘enterprise operates first’ and ‘government subsidizes first’. The results show that the introduction of ‘government subsidizes first’ incentive mechanism and increasing freight rate are helpful in promoting the process of logistics market greening.

Adenomyosis, a benign gynecological condition characterized by the infiltration of endometrial tissue into the myometrium, poses significant challenges to women's reproductive health. Recently, the landscape of adenomyosis diagnosis transformed significantly, thanks to advancements in imaging technologies such as transvaginal ultrasound and magnetic resonance imaging. This lead to a noticeable shift in the demographic profile of patients diagnosed with adenomyosis, including younger women of reproductive age who frequently present with a diverse array of symptoms. Approximately 20% of women are affected by adenomyosis. Adenomyosis manifests with various subtypes, distinct epidemiological profiles, symptomatology, and treatment responses, necessitating tailored approaches for optimal management. Despite its clinical significance, adenomyosis remains understudied, resulting in a significant disparity in research and literature compared to other gynecological conditions. The severity of adenomyosis is compounded when coexisting with endometriosis, particularly deep infiltrating endometriosis (DIE), leading to exacerbated fertility issues and severe symptomatology. The wide range of symptoms, including adverse pregnancy outcomes such as pre-eclampsia, highlights its wider impact and emphasizes the need for increased awareness of the condition. Furthermore, Adenomyosis is frequently associated with treatment failure in endometriosis, contributing to dienogest resistance, elevated discontinuation rates, and persistent pain post endometriosis surgery. Additionally, the lack of specific treatments tailored to adenomyosis poses a considerable challenge in clinical management.

Biosecurity is a tool used to alleviate the introduction, emergence and spread of diseases caused by infectious agents. It comprises different health-management activities that need to be followed to reduce the passage and dissemination of infectious agents within and among farms, poultry flocks, and humans, as well as within a country, among countries, or the whole globe. In terms of public health measures, biosecurity applies to practices that will reduce contact between poultry and humans and thereby reduce zoonotic disease transmission. Two of the common biosecurity measures are bioexclusion and biocontainment which themselves are further categorized as segregation/isolation, movement control and hygiene/sanitation/disinfection. Isolation is about putting poultry under an exclusively isolated environment where it lives alone without any interference from any source external to the poultry or at least under reduced and controlled interference. Movement/traffic control and sanitation measures are practices to follow the isolation of poultry or preparatory phase as in the case of sanitation of poultry houses before introduction of poultry. These techniques have been effective in controlling poultry diseases like avian influenza, exotic Newcastle, Marek’s disease, and any other diseases. Depending upon the underlying situation either bioexclusion or biocontainment measure will be used to control these infectious diseases of poultry.

The objective of the present work was to determine the productivity and costs of timber harvesting and skidding during the first commercial thinning of a Scots pine stand. The analyzed harvesting set consisted of a mini-excavator (34 kW) with an stroke harvester head (gripping range: 4–30 cm), and a farm tractor coupled to an logging trailer with a hydraulic crane. Merchantable timber (roundwood with a minimum diameter of 5 cm inside bark) was harvested from a 25-year old planted Scots pine stand growing on a grid of 1.4×1.8 m. The study showed the productivity of the mini-harvester range from 3.09 to 3.47 m3∙PMH15 -1, and that of the forwarding set to be 4.07 m3∙PMH15 -1. The analyzed model of productivity as a function of individual tree volume and thinning intensity was statistically significant, but the intensity parameter was significant only on plots located along wide access trails (3.7 m) and insignificant on plots located along the narrow access trial (2.5m). The intertree distance was not found to be significant. The calculated net machine costs for the forwarding set and mini-harvester were 36.12 Euro∙PMH 1 and 52.47 Euro∙PMH-1, respectively. An increase in the utilization rate of the harvesting set to 80% would reduce the timber harvesting and skidding costs to 22.07 Euro∙m-3.

The SBA-15 loaded with methylene blue was successfully prepared by sample adsorption of methylene blue in SBA-15 and is characterized by an XRD, SEM, FTIR, and BET. The photocatalytic activity for methyl orange (MO) degradation was investigated under visible light irradiation under LEDs. Experimental results demonstrate that the SBA-15-MB exhibited higher photocatalytic activity than SBA-15 under visible light irradiation. The degradation efficiency of MO (50 ppm) by SBA-15-MB could reach 80% within 180 min under 25W LED visible light. The photocatalytic activity of SBA-15 could be attributed to the excitation of methylene blue by visible light, the transfer of electrons from methylene blue to SBA-15, and the production of radicals at the surface of SBA-15.

In this article, we present two topics related to mathematical economics. We offer an intriguing proposal for securing cost and production functions in the face of uncertainty and risk. We discuss the relationship between individual and social preferences. This is important because traditional revealed preference theory does not account for such factors.

Dealing with randomness is a crucial aspect that cost-effectiveness analysis (CEA) tools need to address, but existing stochastic CEA tools have rarely examined risk and return from the perspective of global benefits. This paper proposes a stochastic CEA tool that supports medical decision-making from the perspective of global benefits of risk and return, the risk-adjusted incremental cost-effectiveness ratio (ICER). The tool has a traditional form of ICER but uses the risk-adjusted expected cost. Theoretically, we prove that the tool can provide marginal medical decisions that promote the risk-return level on global benefits within any intervention structure and can also serve as a discriminating condition for the optimal intervention structure. Numerical simulations within a framework of mean-variance support the conclusions in this paper.

This paper describes how to construct a low-cost magnetic levitation system (MagLev). The MagLev has been intensively used in the engineering education, allowing instructors and students to learn through hands-on experiments essential concepts, such as electronics, electromagnetism, and control systems. Built from scratch, the proposed MagLev depends only on simple, low-cost components readily available on the market. In addition to showing how to construct the MagLev, this paper presents a semi-active control strategy which seems novel when applied in the MagLev. Experiments performed in the laboratory have compared the proposed control scheme with the classical PID control. The corresponding real-time experiments illustrate both the effectiveness of the approach and the potential of the MagLev for education.

One of the key areas of the International Renewable Energy Agency’s (IRENA) programme of work is the analysis of renewable technology costs and performance and the dissemination of these results to as wide an audience as possible. In addition to analysis, IRENA seeks to engage a broad range of stakeholders in the context of this work through the Renewable Costing Alliance. The Costing Alliance brings together companies, industry association, governments and researchers to share, confidentially, data for real-world renewable energy project cost and performance, helping to build further on IRENA’s costing work to date. In this context the authors analyse the current cost differentials and cost reduction potentials for solar PV in Japan compared to best practice levels and identify the reasons for higher costs in Japan and how to reduce them. This study analyses the current installed cost differentials for utility-scale, commercial and residential rooftop solar PV systems. In addition to identifying the reasons for the cost differentials, potential policy recommendations to reduce the cost differential are identified.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

The commercial equipment that carries out the measurement of temperature has a high cost. Therefore, this article describes the development of a temperature measurement equipment, which uses a microcontrolled platform, responsible for managing the data of the collected temperature signals and making available the acquired information, so that they can be verified in real time at the measurement site, or remotely. The construction of the temperature measurement equipment was performed using open platform hardware / software, where performance tests were carried out with the objective of developing a temperature measurement equipment that has measurement quality and low cost.

The capability of extracting information and analyze it into a common format is essential for performing predictions, comparing projects through cost benchmarking, and for having a deeper understanding of the project costs. However, the lack of standardization and the manual inclusion of the data makes this process very time-consuming, unreliable, and inefficient. To tackle this problem, a novel approach with a big impact is presented combining the benefits of data mining, statistics, and machine learning to extract and analyze the information related to railway costs infrastructure data. To validate the suggested approach, data from 23 real historical projects from the client network rail was extracted, allowing their costs to be comparable. Finally, some machine learning and data analytics methods were implemented to identify the most relevant factors allowing for costs benchmarking. The presented method proves the benefits of data extraction being able to gather, analyze and benchmark each project in an efficient manner, and deeply understand the relationships and the relevant factors that matter in infrastructure costs.

An algorithm for the treatment of images affected by both blurring and salt&pepper noise is proposed with a cost only proportional to the number of pixels. The methodology uses a discretization scheme for the Laplace operator multiplied by a suitable nonlinear term depending on the gradient. Even if this approach resembles a diffusion type algorithm, only one step of the procedure is applied, leading to significant time savings. The procedure is successfully tested on some standard black&white natural images.

Presently power control and management play a vigorous role in information technology and power management. Instead of non-renewable power manufacturing, renewable power manufacturing is preferred by every organization for controlling resource consumption, price reduction and efficient power management. Smart grid efficiently satisfies these requirements with the integration of machine learning algorithms. Machine learning algorithms are used in a smart grid for power requirement prediction, power distribution, failure identification etc. The proposed Random Forest-based smart grid system classifies the power grid into different zones like high and low power utilization. The power zones are divided into number of sub-zones and map to random forest branches. The sub-zone and branch mapping process used to identify the quantity of power utilized and the non-utilized in a zone. The non-utilized power quantity and location of power availabilities are identified and distributed the required quantity of power to the requester in a minimal response time and price. The priority power scheduling algorithm collect request from consumer and send the request to producer based on priority. The producer analysed the requester existing power utilization quantity and availability of power for scheduling the power distribution to the requester based on priority. The proposed Random Forest based sustainability and price optimization technique in smart grid experimental results are compared to existing machine learning techniques like SVM, KNN and NB. The proposed random forest-based identification technique identifies the exact location of the power availability, which takes minimal processing time and quick responses to the requestor. Additionally, the smart meter based smart grid technique identifies the faults in short time duration than the conventional energy management technique is also proven in the experimental results.

Vulnerability is the big issue of the small inland urban centers exposed to the risk of depopulation. In the climate and in the context of an increasing seismic risk in the center-northern part of Italy, seismic vulnerability can become the determinant cause of the final abandonment of a small town. In some Italian regions, as well as Emilia Romagna, municipalities are implementing seismic vulnerability reduction policies based on the Emergency Limit Condition that has become a basic reference for ordinary land planning. This study proposes a valuation planning approach to the seismic vulnerability reduction carried out within the general planning framework concerning the Faentina Union, a group of five small towns located in the south-western part of the Province of Ravenna, Italy. The approach consists of three main stages: knowledge – the typological, constructive and technological description of the buildings specifically concerning their vulnerability degree; interpretation – the analyses aimed to outline a range of hypotheses about the damages in case of seism; planning – identifying the works intended to definitely reduce the vulnerability of the buildings. This stage includes a cost modelling tools aimed at outlining the trade-off between the extension and the intensity of the vulnerability reduction works, given the budget.

The Internet of Things (IoT) generates a large volume of data whenever devices are interconnected and exchange data across a network. As a result, there is a range of services with varying needs, for example, capacity requirements, data quality, and latency demands. These services operate on fog computing devices, which are limited in power and bandwidth compared to the cloud. The main challenge is deciding where to implement services on the fog, the cloud, or the hybrid. This paper proposes an efficient allocation technique that pushes processing closer to the network's fog side. It investigates which devices and services may best allocate while preserving resource usage in the IoT architecture. It also examines the importance of allocating services to devices and optimizing resource use in fog computing. In IoT settings, there is a wide range of services and devices; thus, it is critical to effectively assign the services to the devices. We propose Priority-based Service allocation (PSA) and Sort-based Service Allocation (SSA) techniques, which are used to enable an optimum order to employ devices to perform the various services. The experimental results indicate that our proposed technique minimize the data communication over the network by 82% by allocating most of the services locally in fog. We have maximized the number of distributed services to fog devices by 90% while minimizing the wastage of fog resources.

Existing one-shot neural architecture search (NAS) methods have to conduct a search over a giant super-net, which leads to the huge computational cost. To reduce such cost, in this paper, we propose a method, called FTSO, to divide the whole architecture search into two sub-steps. Specifically, in the first step, we only search for the topology, and in the second step, we search for the operators. FTSO not only reduces NAS’s search time from days to 0.68 seconds, but also significantly improves the found architecture's accuracy. Our extensive experiments on ImageNet show that within 18 seconds, FTSO can achieve a 76.4% testing accuracy, 1.5% higher than the SOTA, PC-DARTS. In addition, FTSO can reach a 97.77% testing accuracy, 0.27% higher than the SOTA, with nearly 100% (99.8%) search time saved, when searching on CIFAR10.

Research has shown that second language reading is the bridge that leads to developing otherlanguage skills such as speaking, writing, and vocabulary acquisition. Hence, the present studyaimed to explore adult language learners’ perspectives regarding the most effective andbeneficial reading strategies that can be used to develop their reading competency. Using aqualitative research method, the study examined what specific reading strategies languagelearners believe is effective in developing their reading skills. Analysis of the focus groupsrevealed five different reading strategies mentioned by the participants. These strategies were:Reading Aloud, Silent Reading, Shared Reading, Scanning or Skimming, and Timed Reading. Findings suggest that understanding the use of different reading strategies is important, solanguage teachers need to devote more learning time to introduce reading strategies during ESL classes.

VE is a powerful technique for analyzing a design with a focus on functionality, reducing costs, and increasing value. However, in order to proceed with the design of VE, the theoretical basis for the VE target selection process, which must be preceded in the preparation stage, is lacking, and as a result, it is difficult to verify the most effective target selection. Thus, a theoretical basis is needed. In this study, we intend to quantify the WORTH value of the COST TO WORTH technique and present an objective model of the target selection method using the derived Value Index (VI). For this purpose, cost worth (WORTHC) was calculated based on the performance data of 1,008 cases of 15 building types provided by the Domestic Public Procurement Service and the share of 83 detailed processes in 7 fields. Then, a survey was conducted targeting the ordering companies, and the final worth (WORTHF) was calculated by multiplying the derived customer value (WORTHV ) weight for each detailed work type. We calculated the Value Index (VI) by comparing COST and WORTHF for each detailed construction type of the VE project and developed a model to select construction types that exceed the VI standard value derived using the standard error of the population. Both cost experts and non-cost experts can use the developed model to specify the VE target selection criteria in order to easily select the key target, objectively sort the values that serve as the basis for calculating the value index and make it possible to more easily select the VE target selection criteria based on theoretical evidence. Also, the model can be used to obtain effective detailed design VE results.

Intestinal parasitic infections pose a grave threat to human health, particularly in tropical and subtropical regions. The traditional manual microscopy system of intestinal parasites detection remains the golden standard procedure for the diagnosis of parasites cyst or eggs, but this approach is costly time-consuming (30min/sample), highly tedious, and also required specialist. However, computer vision based on deep learning has made great stride in recent time. Despite the significant advances in deep convolutional neural network-based architectures, little research has been conducted to explore the potential of these techniques in the field of parasitology, specifically for intestinal parasites. Therefore, the goal of this research is to evaluate the performance of proposed state-of-the-art transfer learning architecture for detecting and classifying intestinal parasite eggs from images. We would ensure that patients receive prompt treatment while also relieving experts of extra work if we used such an architecture. Here, in stage first, we applied image pre-processing and augmentation to the dataset, and in stage second, we utilized the YOLOv5 algorithms for detection and classification and then compared their performance based on different parameters. Our algorithms achieved a mean average precision of 97% approximatiely and 8.5 ms detection time per sample for 5,393 intestinal parasite images. Thus, this approach may form a solid theoretical basis for real-time detection and classification in routine clinical examinations while accelerating the process to satisfy increasing demand.

In this study, the fuzzy c- means classifier has been studied with nine other similarity and dissimilarity measures: Manhattan distance, chessboard distance, Bray-Curtis distance, Canberra, Cosine distance, correlation distance, mean absolute difference, median absolute difference and normalised squared Euclidean distance. Both single and composite modes were used with a varying weight constant (m) and also at different α-cuts. The two best single norms obtained were combined to study the effect of composite norms on the datasets used. An image to image accuracy check was conducted to assess the accuracy of the classified images. Fuzzy Error Matrix (FERM) was applied to measure the accuracy assessment outcomes for a Landsat-8 dataset with respect to the Formosat-2 dataset. To conclude FCM classifier with Cosine norm performed better than the conventional Euclidean norm. But, due to the incapability of the FCM classifier to handle noise properly, the classification accuracy was around 75%.

Critical sized bone defects and articular cartilage injuries resulting from trauma, osteonecrosis or age-related degeneration are often nonhealing by the physiological repairing mechanisms, thus representing a clinic issue due to the relevant epidemiological incidence. Current treatment approaches consist of autologous or allogenic grafting, which are associated with painfulness, morbidity, risk of infections and rejection. Novel tissue-engineering approaches, aiming at the reconstruction of damaged tissues, have been proposed as alternative solutions to these conven-tional methods. These approaches are based on the combination of three fundamental compo-nents: autologous or allogenic cells, a scaffold and growth-stimulating signals, which are gener-ally referred to as the tissue engineering triad. Three-dimensional polymer networks are fre-quently used as scaffolds to allow cell proliferation and tissue regeneration. In this scenario, cryogels are giving promising results as cell scaffolds over other polymer networks, thanks to their peculiar properties. In particular, cryogels possess an interconnected porous structure and a typical sponge-like behaviour, which facilitate the cellular infiltration and ingrowth. Their properties can be appropriately adjusted to match the requirements of the specific tissue or or-gan that it is intended to regenerate. In this review it is reported the state of the art on the fabri-cation and employment of cryogels in supporting osteo or chondro-genic differentiation for the re-building of more organized tissues. Moreover, it will highlight current progress and future perspectives in the implementation of this technology in the clinical practice.

Incorporating renewables in the power grid presents challenges for stability, reliability, and operational efficiency. Integrating Energy Storage Systems (ESS) offers a solution by managing unpredictable loads, enhancing reliability, and serving the grid. Hybrid storage solutions have gained attention for specific applications, suggesting higher performance in some respects. This paper compares the performance of hybrid energy storage systems (HESS) to single battery, evaluating their energy supply cost and environmental impact through optimization problems. The model generates an optimized dispatch, minimizing cost or environmental impact of supplying energy to a generic load while considering battery degradation. Seven technologies are assessed, with an example applied to an industrial site contrasting vanadium redox flow (VRFB) and lithium batteries considering the demand of a local load (building). The results also indicates that efficiency and degradation curves have the highest impact in the final costs and environmental functions on the various storage technologies assessed. For the simulations of the example case, a single system only outperforms the hybrid system in cases where lithium efficiency is higher than approximately 87% and vanadium is lower approximately 82%.

The purpose of this study is to analyze the causes of cost variation in natural disaster prevention projects (NDPP) in Gyeongsangbuk-do and to develop effective cost and risk management strategies. The study collected data by conducting an online survey of 244 stakeholders. Binary logistic regression was used to analyze the impact of various variables on cost deviation, in-cluding project management risk (PMR), project costing and execution risk (PCER), project exe-cution strategy risk (PESR), construction project risk (CPR), project cost and schedule risk (PCSR), project management challenges (PMC), and construction project subcontractor and safety man-agement (CPSSM). The results showed that PMR (OR=3.744, 95% C.I. [1.657, 8.457]), PCER (OR=5.068, 95% C.I. [2.236, 11.484]), PESR (OR=3.447, 95% C.I. [1. 853, 6.413]), CPR (OR=2.292, 95% C.I. [1.020, 5.151]), PCSR (OR=4.817, 95% C.I. [2.250, 10.317]), PMC (OR=2.954, 95% C.I. [1.452, 6. 013]), and CPSSM (OR=2.419, 95% C.I. [1.297, 4.515]) had statistically significant effects on cost deviation. In particular, PMR, PCER, and PESR were identified as the main causes, and the effects of additional factors such as CPSSM were also important. The developed predictive model plays an important role in helping stakeholders of NDPP to manage risks in advance and take appro-priate preventive measures to ensure the success of the project. This study empirically supports the theoretical hypotheses of previous studies and provides a clear understanding of the causes of cost deviation in NDPP, which provides important insights for strategic decision-making and provides a new perspective on risk management.

For the majority of the contractual arrangements used in construction projects, the owner is not responsible for the cost deviations due to the variability of labor productivity or material price, amongst many other aspects. Consequently, the cost performance of a project may be entirely distinct for the owner and the contractor. Since the majority of the quantitative research on cost estimation and deviation found in the literature adopts the owners’ perspective, this research provides a contribution towards modelling costs and cost deviation from a contractors’ perspective. From an initial sample of 13 residential building and 10 office building projects, it was possible to develop models for cost estimation at the early stage of development including both endogenous and exogenous variables. Although the sample is relatively small, the authors were able to fully analyze all the cost data, using no secondary sources of data (very frequent in cost modelling studies). The statistically significant variables in the cost estimation models were the areas above and below ground and the years following the 2008 financial crisis, including the international bailout (2011-2014) period. For estimating the unit cost, a nonlinear model was obtained with the number of underground and total floor, the floor ratio and the years following the 2008 financial crisis, including the international bailout (2011-2014) period as predictors. For the office buildings, it was also found a statistically significant correlation between the cost deviation and the number of underground floors.

There has been a steady rise in the recognition of menstrual hygiene management (MHM) as a pressing public health issue due to several advocacy campaigns against its high cost. However, not much of such recognition has been given to it outside the non-profit sector in Nigeria. This is paradoxical considering that most menstruators in Nigeria cannot afford MHM whose cost is considered high even in developed countries. We estimated that the average lifetime cost of MHM in Nigeria is US$1,122.3 per menstruator and US$113.58 billion for the entire menstruating population. Although this cost is relatively lower than in other countries, Nigeria’s low-income level explains why there is a high prevalence of period poverty among menstruators in Nigeria. This commentary highlights the intersected impacts of the cost of MHM and period poverty on the average Nigerian menstruator, his/her family, the economy, the environment and the United Nations Sustainable Development Goals. To alleviate the discussed negative effects, we suggested, as a key recommendation, the national shift from the use of disposable MHM products to that of reusable ones.

There is an urgent need to advance safe and affordable COVID-19 vaccines for low- and middle-income countries of Asia, Africa and Latin America. Such vaccines rely on proven technologies such as recombinant protein-based vaccines to facilitate its transfer for emerging market vaccine manufacturers. Our group is developing a two-pronged approach to advance recombinant protein-based vaccines to prevent COVID-19 caused by SARS CoV2 and other coronavirus infections. One vaccine is based on a yeast-derived (Pichia pastoris) recombinant protein comprised of the receptor binding domain (RBD) of the SARS-CoV formulated on alum and referred to as the CoV RBD219-N1 Vaccine. Potentially this vaccine could be used as a heterologous vaccine against COVID-19. A second vaccine specific for COVID-19 is also being advanced using the corresponding RBD of SARS-CoV-2. The first antigen has already undergone cGMP manufacture and is therefore “shovel ready” for advancing into clinical trials, following vialing and required GLP toxicology testing. Evidence for its potential efficacy to cross-protect against SARS-CoV-2 includes cross-neutralization and binding studies using polyclonal and monoclonal antibodies. Evidence in support of its safety profile include our internal assessments in a mouse challenge model using a lethal mouse adapted SARS strain, which show that SARS-CoV RBD 291N1 (when adsorbed to Alhydrogel®) does not elicit eosinophilic lung pathology. Together these findings suggest that recombinant protein-based vaccines based on the RBD warrant further development to prevent SARS, COVID-19 or other coronaviruses of pandemic potential.

In France, the regional airport’s demand for services is facing challenges due to the continuous expansion of the high-speed train, high-speed line, and highway networks. This study focuses on the viability of regional airports in France through technical efficiency using data envelopment, principle component analysis, Malmquist productivity index, and regression analysis using bootstrapping. To face the current competitive environment, the regional airports in France adopted strategies, such as the construction of low-cost carrier (LCC) dedicated terminals (LCCTs) with lower expenses to attract more LCCs, increasing non-aeronautical revenue, and hosting regional hubs of LCCs. This is the first study that analyzes all of the French regional airports. The findings indicate that the existence of LCCTs positively affects technical efficiency on the airport’s performance, and share of LCCs at a regional airport leads to neither the efficiency nor the profit level.