As an emerging building solution, cross-laminated timber (CLT) floors have been increasingly used in mass timber construction. The current vibration design of CLT floors is conservative due to the assumption of simple support conditions in the floor-to-wall connections. It is noted that end fixity occurs as a result of clamping action at the ends, arising from the gravity load applied by the structure above the floor and by the mechanical fasteners. In this paper, the semi-rigid floor-to-wall connections are treated as elastically restrained edges against rotations to account for the effect of partial constraint. A rotational end-fixity factor was first defined to reflect the relative bending stiffness between CLT floors and elastic restraints at the edges. Then, for the design of vibration serviceability of CLT floors as per the Canadian Standard for Engineering Design in Wood (CSA O86), restraint coefficients were defined and their analytical expressions were derived for natural frequencies and the mid-span deflection under a concentrated load, respectively. In particular, a simplified formula of the restraint coefficient for the fundamental frequency was developed to assist engineers in practical design. At last, by comparing with reported experimental data, the proposed design formula showed excellent agreement with test results. In the end, the proposed end fixity factor with their corresponding restraint coefficients is recommended as an effective mechanics-based approach to account for the effect of end support conditions of CLT floors.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

Background: The effect of velamentous cord insertion (VCI) on perinatal outcomes in twin pregnancies is unclear due to conflicting findings. This retrospective study aimed to examine VCI prevalence and related risk factors in twin pregnancies and its association with adverse perinatal outcomes. Methods: Women with twin pregnancies who delivered between January 2012 and December 2021 in a single tertiary hospital were included. The participants were divided into dichorionic (DC) and monochorionic diamniotic (MCDA) groups, and their maternal and fetal characteristics and VCI rates were compared. Logistic regression models were used to identify risk factors for VCI and VCI-related perinatal outcomes. Results: Among the 694 twin pregnancies included in this study, the VCI rate was significantly higher in MCDA than in DC twins. Body mass index and MCDA twins were significant risk factors for VCI, whereas assisted reproductive technology pregnancy was a significant protective factor against VCI. In DC twins, VCI did not affect perinatal outcomes. Conclusion: In MCDA twins, VCI was a significant risk factor for fetal growth restriction, twin-to-twin transfusion syndrome, and preterm birth at

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

Bartonella species, intracellular parasitic zoonotic pathogens, has drawn increasing attention for their diverse host range and associated human diseases. This study investigates Bartonella infection in small mammals in Yunnan Province, China, focusing on tissue tropism. 333 small mammals were sampled from 13 species, 3 orders, 4 families, and 4 genera in Heqing and Gongshan Counties. Conventional PCR and real-time quantitative PCR (qPCR) were utilized for detection and quantification, followed by bioinformatic analysis of obtained DNA sequences. Results show a 31.5% detection rate, varying across species. Notably, Apodemus chevrieri, Eothenomys eleusis, Niviventer fulvescens, Rattus tanezumi, Episoriculus leucops, Anourosorex squamipes, and Ochotona Thibetana exhibited infection rates of 44.4%, 27.7%, 100.0%, 6.3%, 60.0%, 23.5%, and 22.2%, respectively. Genetic analysis identified 30, 10, and 5 strains based on ssrA, rpoB, and gltA genes, with nucleotide identities ranging from 92.1% to 100.0%. Bartonella strains were assigned to B. grahamii, B. rochalimae, B. sendai, B. koshimizu, B. phoceensis, B. taylorii, and a new species identified in the Episoriculus leucops (GS136). Tissue distribution analysis revealed varied copy numbers across different tissues, with the highest load in spleen. These findings underscore Bartonella's diverse species and host range in Yunnan Province, highlighting its broad tissue tropism in small mammals.

Zanthoxylum armatum is an forest tree with apomixis characteristic, and RWP-RKs are plant-specific transcription factors known to regulate nitrogen response and embryonic development. However, the genome-wide analysis of RWP-RK family genes in Z.armatum is unclear. In this study, 36 ZaRWP-RK transcription factors were identified in the genome of Z.armatum, among which 15 genes were belonged to the RKD subfamily and 21 belonged to the NLP subfamily. Duplication events of ZaRWP-RK genes were mainly segmental duplication, and synteny analysis revealed close phylogenetic relationship between Z.armatum and Arabidopsis. The analysis of cis-elements indicated that ZaRWP-RK genes may be involved in the regulation of embryonic development of Z.armatum by responding to plant hormones such as abscisic acid, auxin, and gibberellin. Real-time PCR showed that the expression levels of most ZaRWP-RK genes were significantly increased from flowers to young fruits. Protein-protein interaction network analysis further revealed the potential roles of the ZaRWP-RK proteins in apomixis. Collectively, this study provide a theoretical basis for future investigations into the ZaRWP-RK genes and their regulatory mechanisms in the apomixis process of Z.armatum.

Forest resources are renewable,rational exploitation and utilization of forest resources are not only conducive to sustainable development of population, but also can obtain higher economic benefits. Based on actual timber harvesting problems,a combined harvesting model of timber and non-timber with nonlinear harvesting term was established.Firstly, using the qualitative theory of ordinary differential equations, the dynamic behavior of the model is studied, and the existence and stability of the equilibrium point of the model are proved .Secondly, the optimal control solution is obtained by using the optimal control theory.Finally, the optimal harvesting strategy of timber and non-timber products is given based on the numerical simulation results, which provides a certain theoretical basis for the sustainable development of forestry ecological economy.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

Natural vegetation restoration can take decades to achieve and requires information on species composition and trend to inform management strategies. Here we demonstrate the potential and portability of drone, dove and Sentinel-2 imagery for species level classification and trajectory monitoring using three study sites with different revegetation histories. Drone imagery (4 cm) was classified using random forests. Dove (3 m) and Sentinel-2 (10 m) images were acquired close to the anniversary of the drone flights and converted into fractional cover maps showing the proportion of exotics, natives and other land covers using ordinary least squares (OLS) and geographically weighted regression (GWR). The time series of fractional cover maps were converted into positive and negative slope and second-order curvature and summarised as one RGB composite to illustrate trend and observe exotic expansion. Drone classification accuracies ranged from 73%-76% when applied to the full plant species list and between 93% and 97% when grouped into natives, exotics, and other land covers. GWR outperformed OLS for all fractional cover mapping and GWR with dove imagery was more accurate than with Sentinel imagery. The combination of very high-resolution drone acquired imagery with the versatility of dove acquired imagery arms land managers with highly accurate species composition and their spatio-temporal dynamics to promote timely intervention.

Numerous approaches address over-fitting in neural networks: by imposing a penalty on the parameters of the network (L1, L2, etc); by changing the network stochastically (drop-out, Gaussian noise, etc.); or by transforming the input data (batch normalization, etc.). In contrast, we aim to ensure that a minimum amount of supporting evidence is present when fitting the model parameters to the training data. This, at the single neuron level, is equivalent to ensuring that both sides of the separating hyperplane (for a standard artificial neuron) have a minimum number of data points — noting that these points need not belong to the same class for the inner layers. We firstly benchmark the results of this approach on the standard Fashion-MINST dataset, comparing it to various regularization techniques. Interestingly, we note that by nudging each neuron to divide, at least in part, its input data, the resulting networks make use of each neuron, avoiding a hyperplane completely on one side of its input data (which is equivalent to a constant into the next layers). To illustrate this point, we study the prevalence of saturated nodes throughout training, showing that neurons are activated more frequently and earlier in training when using this regularization approach. A direct consequence of the improved neuron activation is that deep networks are now easier to train. This is crucially important when the network topology is not known a priori and fitting often remains stuck in a suboptimal local minima. We demonstrate this property by training a network of increasing depth (and constant width): most regularization approaches will result in increasingly frequent training failures (over different random seeds) whilst the proposed evidence-based regularization significantly outperforms in its ability to train deep networks.

Background: The practice of self-medication is common worldwide and is an important component of medical self-care. However, the practice can be dangerous and is linked to various risks for the patients and the entire community. This study aimed to estimate the prevalence and factors associated with self-medication among Bangladeshi adults. Methods: A cross-sectional survey was conducted between April and June 2021 among Bangladeshi adults (aged >19 years) using convenient sampling. A total of 1320 data were collected through face-to-face interviews using a standardized questionnaire. Multivariable logistic regression analysis was used to identify factors associated with self-medication practice (SMP). Results: Overall, 41% of adults in our survey reported SMP. The most common illnesses that prompted SMP were common cold/flu (66.4%), gastric problems (65%), and headache (64.4%). The most frequent reasons for SMP were to get better services (30.59%), perceive SMP without side effects (23.28%), and save time with effectiveness (14.56%). Potential risk factors included 10 years (AOR = 1.91; 95% CI: 1.04 - 3.50) and >12 years of schooling (AOR = 5.03; 95% CI: 2.27 - 11.15), being a businessman (AOR = 4.64; 95% CI: 1.74 - 12.37), having ≤6 family members (AOR = 2.13; 95% CI: 1.40 - 3.24), being a member of a social group (AOR = 1.53; 95% CI: 1.10 - 2.12), a health status check after every six months (AOR = 1.52; 95% CI: 1.08 - 2.13), and current ill-health (AOR = 1.41; 95% CI: 1.06 - 1.87). Protective factors identified included ≤30 years of age (AOR = 0.40; 95% CI: 0.17 - 0.93), and practice of modern (AOR = 0.39; 95% CI: 0.22- 0.69) and herbal (AOR = 0.45; 95% CI: 0.21- 0.97) healing types. Conclusion: More than one-third of the study participants reported practicing self-medication. Increasing the community’s awareness of the extreme consequences of SMP and not just the average experience might sway individuals away from SMP, and implementing strict jurisdiction could be a way to minimize the SMP.

Current VAT rules for cross-border e-commerce companies in the EU are not sustainable, because they are extremely complex and often opaque, due to the lack of tax harmonization. The aim of the research is to explore, using a qualitative method, what kind of harmonization would make the current legislation more uniform, simpler, more transparent, and easier to understand, without conflicting with the rules of any Member State. To this end, the aspects of the new platform regulation introduced on 1 July 2021 and its potential for expansion are assessed through information from possible sales models. The research suggests that the rules on platforms do not cover all possible sales models, which in our view imposes an unnecessary extra administrative burden on some businesses and makes their tax activities less transparent. In the light of the results of the research, we propose that the current EU platform regulation should be extended to cover B2B, B2C transactions and services. As a result of this suggested harmonization, a simpler, more transparent, uniform and sustainable tax system would contribute to the whitening of the economy, generating additional tax revenue for Member States.

Forest enterprise has been identified as a means of generating income among people; plays a vital role in enhancing the quality of life of forest-dependent people. Despite the opportunities timber marketing offers the people, the disparities in the income generation of the marketers in the Bodija sawn wood Market and the effect of socio-economic factors on income generation of the marketers is not well understood. This study was conducted to assess the socio-economic determinants of contributions of timber marketing to the income of timber merchants in Bodija sawn-wood Market. One hundred structured questionnaires were administered randomly in five zones of the sawn wood Market to obtain information on the socio-economic background of the sawn wood marketers and the contribution of timber trade to their incomes. The result indicated that 99.0% of the respondents were male while females constituted 1.00%. Seventy-five percent of the marketers had post-primary education and 25% had primary education. Two percent of the marketers had below 10 years of marketing experience, twenty-six percent had between 11 and 20 years, 57.00% had between 21 and 30 years, and 15.00% had more than 30years experience. Fifty-eight percent of the respondents earned between ₦10000-₦60000 (1US$ = 360.00) from timber marketing, thirty-one percent earned between ₦60001 and ₦110000, 7% earned between ₦110001 and ₦160000, while 4% earned above ₦160000 per month. Chi-square analysis of the socio-economic characteristics of the respondents and income generation at α level of 0.05 indicated that ethnicity (0.001) and years of experience (0.009) significantly influenced income while the level of education (0.101), age (0.122), and religion (0.745) had no significant influence on the incomes of marketers. Experience is an important factor in sawn wood marketing and a major determinant of the contribution of timber marketing to the income of timber marketers in Bodija sawn wood Market.

Safe water is a global public health concern amid increasing scarcity and pollution. Bottled water production and consumption contribute to these problems. This study examines tap water consumption in Italy, assessing associated sociodemographic factors and related health outcomes such as obesity and self-perceived health status. Data from the Italian National Statistics Institute's "Aspects of daily life" survey (N=45,597) were analyzed. Covariates included education, age, gender, economic status, region, concerns about waste and climate change, consumption of carbonated drinks excluding water, alcohol consumption, consumption of vegetables, consumption of snacks, body mass index, and self-perceived health status. Bivariate analyses and mixed-effect logistic regression models explored the associations. People who drink tap water were 19,674 with a higher prevalence in people aged 45 to 59 old, people with a graduate/post-graduate degree diploma, with optimal economic resources, and concerned about waste production and climate change, coming from the North-East regions of Italy. Underweight people showed a higher prevalence of TW assumption as well as those who drink less than occasionally carbonated drinks, drink alcohol, consume vegetables more than once a day, and snacks less than once a week with a satisfying level perceived health status. Regressions showed that all age classes are less likely to drink tap water than people younger than 20 years old. The category with “inadequate” economic resources is more likely to consume tap water. Low educational classes show a low likelihood of consuming tap water as well as Islands. A concern about waste production and climate change is associated with an increased likelihood of assuming tap water. Tap water consumption was negatively associate with obesity but not with a satisfactory Self-perceived health status. Insights from this study can inform public health strategies.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

Domain generalization has led to remarkable achievements in Hyperspectral Image (HSI) classification. Inspired by contrastive language-image pre-training (CLIP), the language-aware domain generalization method has been explored to learn cross-domain-invariant representation. However, existing methods face some challenges: 1) The weak capacity to extract long-range contextual information and inter-class correlation. 2) Due to the inadequacies of the large-scale pre-training for HSI data, the spatial-spectral features of HSI and linguistic features can not be straightforwardly alignment. To address the above problems, a novel network has been proposed with a CLIP framework, which consists of an image encoder, based on an encoder-only transformer to obtain the global contextual information and inter-class correlation, a frozen text encoder, and a cross-attention mechanism, named Linguistic-Interact-with-Visual Engager (LIVE), enhances the interaction between two modalities. Extensive experiments demonstrating superior performance over state-of-the-art methods in HSI Domain Generalization with a CLIP framework.

Understanding the dynamics of teamwork and communication among healthcare professionals is crucial in the face of evolving healthcare challenges. This study assessed relational coordination among healthcare professionals in the South Tyrolean healthcare system in Italy, focusing on communication and teamwork dynamics in a cross-sectional survey. Using the validated Relational Coordination Survey (RCS) instrument and 525 completed online responses, the questionnaire aimed to understand the implications of different levels of relational coordination ratings by general practitioners, hospital physicians, nurses, and administrative personnel (response rate 26%). The demographics of the participants revealed a predominance of female professionals (64%), with an average age of 50 and 18 years of service. The resulting RCS scores varied significantly across professional groups, with nurses reporting the highest within-group scores, indicating moderate coordination, and administrators reporting the lowest scores, reflecting areas of weak coordination. Between-group relational coordination was generally perceived as weak across professional groups, with the least weakness observed between general practitioners and nurses. German or Italian language and health district affiliation emerged as significant factors influencing relational coordination ratings, highlighting the need for differentiated understanding and strategies in multilingual and diverse regional settings. Assessments of interdisciplinary feedback and referral practices highlight the variation in teamwork and communication weaknesses and underscore the need for targeted interventions to improve relational coordination. This study provides insights into the complexity of relational dynamics in health care settings. It suggests that improving relational coordination through tailored strategies could significantly improve team effectiveness, quality of patient care, and overall system efficiency.

In the context of sustainable development, integrating the work aspect into health promotion systems is essential, ensuring that employees maintain a healthy balance between their professional and personal lives, which respects and amplifies the potential of every individual. Lately, there has been a noticeable shift of medical professionals from the public to the private sector. This trend paints a bleak picture, highlighting the vulnerabilities of a system teetering on the brink of failure, with significant impacts on patient care. Among the myriad reasons behind this shift, burnout stands out prominently. Medical professionals face increasing pressures due to understaffing, limited organizational support, and insufficient resources, leading to feelings of cynicism, exhaustion, and detachment from their roles. Utilizing the Maslach et al. questionnaire, we assessed the risk of burnout among physicians in public hospitals to identify and underscore preventive measures and improvements, correlating our findings with key aspects of organizational empowerment. Our research indicates that enhancing interpersonal relationships and resources—both within teams and between the organization and its physicians—is crucial for the revival of the healthcare system. This approach aims at improving the delivery of healthcare services and offering appropriate recognition to healthcare professionals, aligning with the principles of sustainable employment.

The advancement of mechanization in forestry has increased productivity in the forestry sector, bringing positive and negative impacts that require a deeper understanding for sustainable forest management. This study aimed to apply a simplified instrument for assessing damage and environmental impacts in forest harvesting of commercial eucalyptus plantations, using a combination of methodologies. The methodology used combined interaction networks and impact assessment matrices, carrying out field surveys, transposing them to interaction networks and weighting them through assessment matrices, resulting in environmental indices (ES) for prioritizing actions. The study was conducted on a commercial eucalyptus plantation in the municipality of São Pedro, São Paulo, Brazil. The mechanized harvesting of the area consists of the structure of a module with a mobile unit consisting of a harvester and forwarder. The results indicated that wood transport presented the highest ES, both positive and negative. The most significant negative impacts (ES) were the depletion of water resources and erosion, while the positive impacts included regional development and job creation. The most notable changes, positive and negative, were observed in the physical and anthropic environment, with a lesser impact on the biotic environment.

Globally, over the past several months millions of persons contracted the coronavirus disease 2019 (COVID-19) resulting in significant mortality. Health care systems are negatively impacted including the care of individuals with cancers and other chronic diseases such as chronic active hepatitis, cirrhosis and hepatocellular carcinoma. There are various probable pathogenic mechanisms that have been presented to account for liver injury in COVID-19 patients such as hepatotoxicity cause by therapeutic drugs, severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection of the bile duct cells and hepatocytes, hypoxia and systemic inflammatory response. Liver biochemistry tests such as AST, ALT, GGT and ALP are deranged in COVID-19 patients with liver injury. Hepatocellular damage results in the elevation of serum AST and ALT levels in early onset disease while a cholestatic pattern that develops as the disease progress causes higher levels of ALP, GGT, direct and total bilirubin. These liver biochemistry tests are prognostic markers of disease severity and should be carefully monitored in COVID-19 patients. We conducted a systematic review of abnormal liver biochemistry tests in COVID-19 and the possible pathogenesis involved. Significant findings regarding the severity, hepatocellular pattern, incidence and related clinical outcomes in COVID-19 patients are highlighted.

In this study, an experiment was conducted on hoop pine (Araucaria cunninghamii), which is a common tree species in Taiwan. Holes with diameters of 4, 5, 7, 10, 12, and 14 cm were drilled in dry hoop pine timber with a diameter of 39 cm and a height of 57 cm, and an 800 MHz Ground Penetrating Radar (GPR) antenna were used to determine the minimum image resolution and the size of the holes in the wood. GPR images of the timber were subjected to a filtering process to obtain characteristic reflection curves of the damage to the timber. Curves with clear waveforms were observed in the GPR profiles of eccentric holes with a diameter of 4 cm. Profiles of the damage were obtained and profile images with the trunk radius at the centre were transformed into polar coordinate images. From these polar coordinate images, the location, size and diameter of the eccentric holes in the wood were identified, and the reflection curves were characterised by waveforms and irregular fluctuations. The risk levels of tree trunks were determined on the basis of their t/R (minimum normal wall thickness of the cross-section of the trunk/radius of the trunk) values and hole area ratios. A comparison between the GPR-based results and the actual diameters of the holes revealed that the filtered GPR profiles could be used for the efficient and accurate assessment of damage to hoop pine timber (average error rate ≤ 4%).

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

In previous work (Z. Angew. Math. Phys. 68(2), 2017), Apalara considered a one dimensional thermoelastic laminated beam under Cattaneo’s law of heat conduction and proved the exponential and polynomial decay results depend on the stability number χ_T . In this paper, we continue to study the same system and show that the solution of the concerned system lacks of exponential decay result in the case χ_T ≠ 0 which solves the open problem proposed by Apalara (Z. Angew. Math. Phys. 68(2), 2017).

Despite the importance of influenza vaccination for healthcare workers (HCWs), their uptake remains challenging. This study aimed to measure influenza vaccine hesitancy among HCWs in Nakhon Phanom province, Thailand. A representative cross-sectional survey was conducted at six hospitals during August – September 2020 using a self-administered questionnaire. HCWs delaying getting influenza vaccines, accepting but unsure, or refusing with doubts were categorized as hesitant. Those accepting without any doubts were classified as non-hesitant. Vaccine hesitancy determinants were identified by multivariable logistic regression analysis. A total of 338 participants (97%) completed the questionnaires; most were female nurses working at district hospitals without pre-existing chronic medical conditions. Nearly 60% of participants (197/338) exhibited influenza vaccine hesitancy, and significant factors included age above 50 years adjusted odds ratio [aOR] 3.2, 95% CI 1.3-8.5), fair knowledge of influenza/vaccination (aOR 0.4, 95% CI 0.2-0.8), and negative influence of other HCW (High level– aOR 2.3, 95% CI 1.1-4.8; Moderate level- aOR 2.1, 95% CI 1.1-4.4). Imparting updated information to the HCW combined with positive guidance from influential peers may help reduce this hesitancy.

Amazon tropical forest is actually subject to strong deforestation, generally originated from illegal logging, resulting in ecological, environmental and economic problems. Aiming stop deforestation and timber commercialization of illegal logging of tropical forest, new laws has been introduced in many countries. Here we investigated the utility of DNA fingerprinting of nuclear and cytoplasmatic SNPs to timber tracking the intensive logged and commercialized of the Amazonian Neotropical tree Jacaranda copaia. Samples of 832 individuals from 43 populations from Bolivia, Brazil, French Guiana, and Peru were used to investigate the power of 113 nuclear SNPs, 11 CpSNPs, and four MtSNP loci to determine the country and population origin. The genetic differentiation among all populations and contries was high (0.233–0.942), specialy for CpMtSNP (generally>0.6) loci, and there is a strong isolation by distance pathern among populations, favoring the group or individual samples tracking to correct site. For self-assignment tests, we were able to 100% correct determine country and population origin of all samples using all SNPs. Our results show that the use of 128 SNP markers is suitable to correct determination of country and population site of J. copaia timber origin and very useful tool for customs and local and international policies.

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

In this paper, we investigate the stabilization of a one-dimensional thermoelastic laminated beam with structural damping, coupled to a heat equation modeling an expectedly dissipative effect through heat conduction governed by Gurtin-Pipkin thermal law. Under some assumptions on the relaxation function g, we establish the well-posedness for the problem. Furthermore, we prove the exponential stability and lack of exponential stability for the problem. To achieve our goals, we make use of the semigroup method, the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem.

In order to understand the hot deformation behavior of novel Cu/Al laminated composites, isothermal hot compression tests were conducted by Gleeble-1500D thermo-mechanical simulator. And the effect of bonding interface, deformation temperature and strain rate on the deformation behavior was analyzed. Results show that under the interface constraint effect, soft Al layer trends to flow synchronously with hard Cu layer. And further microstructure examinations indicate the cooperative deformation capability of Cu/Al composites increases with increasing stain rate and decreasing deformation temperature. Strain hardening exponent, calculated based on the true stress-true strain data, also proves the effect of deformation temperature and strain rate on the cooperative deformation behavior. Meanwhile, unique composites structure allows the Al matrix to exhibit the characteristic of dynamic recrystallization during the hot deformation process. Lastly, strain compensated Arrhenius-type constitutive equation was employed to describe the coupling effect of temperature, strain rate and strain on the flow stress.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

The uptake of buildings employing cross-laminated timber (CLT) assemblies and designed to Passivhaus standard has accelerated internationally over the past two decades due to several factors including design responses to the climate crisis by decarbonising the building stock. Structural CLT technology and the voluntary Passivhaus certification both show measurable benefits in reducing energy consumption, while contributing to durability and indoor comfort. However, there is a general lack of evidence to support a fast uptake of these technologies in Australia. This paper responds to the compelling need of providing quantitative data and adoption strategies, it explores their combined application as a potential pathway for climate-appropriate design of energy-efficient and durable mass timber envelope solutions for subtropical and tropical Australian climates. Hygrothermal risk assessments of interstitial condensation and mould growth of CLT wall assemblies inform best-practice design of mass timber buildings in hot and humid climates. This research found that the durability of mass timber buildings located in hot and humid climates may benefit from implementing the Passivhaus standard to manage interior conditions. The findings also suggested that climate-specific design of the wall assembly is critical for mass timber buildings, in conjunction with excellent stormwater management practices during construction and corrosion protection for metallic fasteners.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

Non-timber forest Products (NTFPs) are a broad category of natural resources harvested from forests that do not involve cutting down trees for their wood or timber. NTFPs play a vital role in the livelihoods and economies of many rural communities, particularly in forest-dependent regions. Despite the benefits obtained from NTFPS, little is known about its potential to alleviate poverty in the local communities. The objective of this review is to comprehensively assess the potential of NTFP's contribution to poverty reduction within forest fringe communities. The study employed the systematic review method to delve into the multifaceted relationship between NTFPs and poverty alleviation. We followed the preferred reporting items for systematic reviews and meta-analyses protocol (PRISM-P). In all, 58 research articles were reviewed. The results indicated that NTFPs hold significant promise as a tool for poverty alleviation. Globally, NTFPs have the potential to alleviate poverty and increase household incomes between 19% and 78% within forest fringe rural communities. In addition, the review indicated that countries in Africa and Asia depend highly on NTFPs and provide substantial amounts of income to the locals. However, the potential for NTFPs to reduce poverty is not uniform. It is highly contingent upon local ecological conditions, market accessibility, community involvement, and supporting policies and interventions. In conclusion, this systematic review demonstrates that NTFPs have a substantial role in poverty alleviation. This study underscores the need for continued research and targeted development initiatives to unlock the vast potential of NTFPs in addressing poverty challenges.

Forests are a large reservoir of biodiversity on which riparian populations frequently rely. Non-timber forest products (NTFPs) are an important source of income for millions of people living in forest-adjacent communities. This study aims at characterizing the types and uses of NTFPs in order to determine whether their exploitation in the eastern Democratic Republic of the Congo is sustainable. Interviews and direct observation were carried out with NTFP stakeholders (harvesters, sellers, and consumers) in Kalonge, near the Kahuzi-Biega National Park. The results showed that 40 NTFPs of plant origin and 10 NTFPs of animal origin are commonly exploited and used in food and traditional medicine. The most common NTFP harvesting techniques are debarking, picking, digging up, felling, and wine extraction, which are all tailored to the plant part. A significant relationship (p-value< 0.001) has been established between the types of NTFPs used and harvesting methods as well as between the types of NTFPs used and organs retrieved. NTFP products are mainly obtained from the natural forest KBNP but also in the woodland, trees grown outside of forest or through domestication. Their abundance, however, is hampered by the extraction of wood for charcoal, energy, and timber, as well as agricultural expansion. The supply of NTFPs is determined by the market demand for the products, the nature of the product, and the ease of disposal. The NTFPs value chain in Kalonge is important to the local economy, however exploitation of NTFP products remains uncontrolled and should be well managed to ensure sustainability.

Wood-borer extermination by a dry heat clean-up is the essential method from the point of view of sustainability of historical wooden structures like trusses and ceilings in heritage-listed buildings. The wooden components are heated by a hot air of temperature about 100°C until the temperature in the centre of the wooden structures reaches 55°C to kill the wood-borers. In this article we review the method and present solution of the heat equation for structural wooden components. We also suggest an approximate formula that enables to estimate the necessary heating time for different cross sections of wooden components and can be used in technical application of the method.

In this study, cotton fabric reinforced phenolic resin (CPF) composites were modified by adding four two-dimensional fillers: graphitic carbon nitride (g-C3N4), graphite (Gr), molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN). The tribological properties of these modified materials were investigated under dry friction and water lubrication conditions. CPF/ Gr composite exhibits significantly better tribological performance than the other three fillers modified CPF composites under dry friction, with a 24% reduction in friction coefficient and a 78% reduction in wear rate compared to unmodified CPF composite. Under water lubrication conditions, all four fillers did not significantly alter the friction coefficient of the CPF composite. However, except for an excessive amount of Gr, the other three fillers can reduce the wear rate. Particularly, in the case of 10% MoS2 content, the wear rate decreased by 56%. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed for the analysis of the morphology and composition of the transfer films. Additionally, molecular dynamics (MD) simulations were conducted to investigate the adsorption effects of Gr, MoS2, and PF on the counterpart surface under both dry friction and water lubrication conditions. The difference in the adsorption capacity of Gr and MoS2 on the counterpart, as well as the resulting formation of transfer films, accounts for the variation in tribological behavior between CPF/Gr and CPF/MoS2 composites. By combining the lubrication properties of MoS2 and Gr under dry friction and water lubrication conditions, using them as co-fillers can achieve a synergistic lubrication effect.

This study aimed to investigate the relationship between sleep duration, dementia severity, age, and ANS regulation. This cross-sectional pilot study included 27 older patients with probable Alzheimer’s disease, hospitalized at a psychiatric center. We measured heart rate variability to assess ANS regulation at night, evaluated dementia severity using the Clinical Dementia Rating scale, and obtained sleep duration data from sleep diaries maintained by psychiatric nurses. The data were analyzed using repeated-measures generalized linear models with age, sex, dementia severity, and medication (antipsychotics) as covariates. A sleep duration of 7–8 h per night was associated with better ANS regulation than other sleep durations, as indicated by sympathovagal balance (p = 0.005). ANS dysregulation was characterized by a 20.7% increase in sympathetic nervous system activity and a 14.8% decrease in parasympathetic nervous system (PSNS) activity. We found a significant correlation between dementia severity and PSNS activity (p = 0.04) and observed an inverted U-shaped association between sleep duration and ANS regulation. This pilot study demonstrated that a sleep duration of 7–8 h per night may be critical in maintaining optimal ANS regulation. Bidirectional associations between sleep duration, inadequate sleep duration, aging, and ANS regulation warrant further investigation.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

Cancer cells require substantial amounts of energy and substrates for their metabolic hyperactivity, enabling the synthesis of new cells at the expense of healthy ones. Preliminary in vitro data suggest that a mix of free essential amino acids (EAA-mix) can promote cancer cell apoptosis by enhancing autophagy. This study aimed to confirm, both in vitro and in vivo, whether EAA intake could influence the development of colon cancer in mice. We investigated changes in cancer proliferation in CT26 cells treated with EAA-mix, and in mice fed with EAA rich modified diets (EAARD) as compared to those on a standard laboratory diet (StD). CT26 cells were injected subcutaneously (s.c.) or intraperitoneally (i.p.). After 21 days, tumors were removed and measured. In vitro data corroborated that EAA-mix impairs cancer growth by inducing autophagy and apoptosis. In vivo data revealed that mice on StD developed significantly larger (s.c.) and more numerous (i.p.) cancers than those on EAARD. EAA administration appears to influence cancer cell survival with notable anti-proliferative properties.

Hybrid woven kenaf-carbon composite were fabricated in this study using epoxy resin as matrix. Effects of different fabric material namely weave designs (plain and satin) and fabric counts (5×5 and 6×6) on the properties of laminated woven kenaf polymer composite were evaluated. This study evaluates the mechanical and morphological properties of hybrid fabric kenaf-carbon from kenaf yarn of 500tex. Kenaf and carbon fabrics were used in this work, where vacuum infusion technique was selected to prepare the composite and epoxy resin was used as a matrix. The fibre weight content is 30% and four specimens were prepared for each samples and tested for their tensile, flexural, and impact strengths. The morphological properties of composites were analysed through the scanning electron microscope (SEM). The results revealed that plain woven fabric is favourable in terms of tensile and impact strengths compared to satin woven fabric. Meanwhile, 5×5 of fabric count gives better flexural modulus than composite fabricated with 6×6 fabric count. The morphologies of the fractured surface investigated by SEM demonstrated better adhesion properties and less fibre pull-out on plain woven fabric.

Composite timber-concrete constructions are innovative structural systems which have become the subject of research and practical usage, primarily due to their attractive mechanical properties. This article deals with the experimental procedure and the analysis of the mechanical behavior of two different serious of timber-concrete composite beams. In the composite beams of the A series, screws were used as a fastening system in the interlayer between the timber and concrete parts, whereas in the B type series, a more complex system, the combination of notches and screws, was used for the same purpose. Both series were exposed to loading up to a fracture point by the means of the standard procedure (four point bending test). The mechanical behavior of the A and B-series beams was analyzed by a comparative analysis referring to: the correlation of the fracture loading and the deflection at the moment of fracture, forms and mechanisms of fracture, the development of dilatations at certain points of specific cross-sections, the displacement in the timber-concrete interlayer in the support zones, the value of shear stresses and the calculated values of the effective bending stiffness of the beams. The B-series beams where a more complex fastening system, as it was expected, showed a better mechanical behavior than the A-series beams.

The issue of environmental sustainability is increasingly topical and one of the most impactful sectors is that of the construction industry. As stated in the reports of the GlobalABC, the building sector is the main responsible for GHG emissions, generating about 37% of global CO2e emissions. Already during the phases of production and construction of buildings about 10% of global emissions are produced, while the remaining part comes from their use, from the energy for air conditioning and lighting. Reducing emissions in the pre-use phase of buildings is therefore a crucial issue for combating climate change. The research investigates the potential of timber construction systems, thanks to the carbon storage property of the material. The proposed calculation methodology is structured according to the LCA-Life Cycle Assessment approach, referring to the C2H phase (from Cradle-To-Handover), and evaluates emissions related to the production and construction of buildings. To identify the timber construction system that minimizes CO2e emissions, within the limits of the investigation (A1-A5 phases), the method was applied to two buildings built with different technologies: one with X-Lam panels and one with a framed structure. The results were analyzed, compared, and discussed to demonstrate that the timber buildings are the most virtuous solution in the Net Zero Carbon perspective by 2050.

Efforts to quantify and reduce greenhouse gas (GHG) emissions of the built environment often neglect embodied emissions, instead focusing on reducing emissions from building operations. Utilizing sustainably sourced mass timber offers low embodied carbon alternatives to traditional concrete and steel structural systems, however the variability in embodied carbon for different mass timber approaches remains understudied. In this study, we used life cycle assessment (LCA) to compare the whole building embodied carbon of nine mass timber design options and two typical concrete and steel reference cases for an eight-story mixed-use building, ensuring structural, acoustic, thermal, programmatic, and fire-rating equivalence between the designs. The study found that the mass timber designs vary significantly, ranging between a 14-52% reduction in whole building embodied carbon from the most impactful reference case, and a 31-73% reduction when considering the structural systems alone. This study demonstrates the value that whole building LCA (WBLCA) provides as a primary driver for low-carbon structural system design and architectural development of mass timber buildings, beyond that of single material comparisons using environmental product declarations (EPDs).

A micromechanical model is implemented to indicate the progressive fatigue problem of a laminated composite with a central circular hole under fatigue loading based on a finite element model. The mechanical properties of the composite lamina are represented based on the characteristics of the fiber and the matrix through a micromechanics model. An appropriate algorithm is then adopted to simulate fatigue damage development in the composite lamina. According to this algorithm, the stress field of the composite subjected to fatigue load is initially obtained using the finite element method. Finally, the predicted results of the stresses in the constituents i.e. fiber and matrix are determined according to the micromechanical bridging model. Finally applying proper damage driving relations leads to damage degree in each element. The proposed model is proven to be successful in the observation of the fatigue behavior with stiffness degradation in each element of the composite in each cycle. Results are reported and validated using those micromechanical models and experimental data available in the literature.

The Fruit Harvest Helper, a mobile application developed by Northwest Nazarene University’s (NNU) Robotics Vision Lab, aims to assist farmers in estimating fruit yield for apple orchards. Currently, farmers manually estimate the fruit yield for an orchard, which is a laborious task. Fruit Harvest Helper seeks to simplify their process. While prior research efforts at NNU concentrated on developing an iOS app for blossom detection, this current research aims to adapt that smart farming application for apple detection across multiple platforms, iOS and Android. The old and new applications were designed with an intuitive user interface that is easy for farmers to use, allowing for quick image selection and processing. Unlike before, the adapted app utilizes a color ratio-based image segmentation algorithm implemented in OpenCV C++ to detect apples in apple tree images selected for processing. The results of testing the algorithm with a dataset of images indicate an 8.52% Mean Absolute Percentage Error (MAPE) and a Pearson correlation coefficient of 0.6 between detected and actual apples on the trees. These findings were obtained by evaluating the images from both the east and west sides of the trees, which was the best method to reduce the error of this algorithm. Although the Fruit Harvest Helper shows promise, there are many opportunities for improvement. These opportunities include exploring alternative machine-learning approaches for apple detection, conducting real-world testing without any human assistance, and expanding the app to detect various types of fruit. The Fruit Harvest Helper mobile application is among the many mobile applications contributing to precision agriculture, nearing readiness for farmers to use in yield monitoring and farm management.

The study aimed to estimate the prevalence of respiratory symptoms and to assess respiratory health risks associated with Particulate Matter (PM) exposure among the residents of Windhoek, Namibia. Objectives: To measure particulate pollution concentration in Windhoek through monitoring of particulate matter concentration and to identify any associations between particulate pollution, individual location and respiratory health among the Windhoek resident’s. Methods: an adapted standardized self-administered questionnaire was used to collect respiratory health related data as well as previous exposure, while PM monitoring was done using ASTM D1739 reference method. Results: A high prevalence was observed for cough (43%), breathlessness (25%), and Asthma (11.2%). PM was found to be a significant risk factor for episode of cough and phlegm, while high PM exposure category had increased odds ratio for episode of phlegm and cough (OR: 2.5, 95% CI: 0.8-8.0). No association was observed between location and respiratory health outcomes. Conclusion: The study found high levels of PM concentration across all Windhoek suburbs which were above the German, American and EPA. Enactment of legislation relating to the control and monitoring of PM related emissions at point of generation is required at country and city level.

Research Highlights: The study determined that selective thinning causes different responses, the initial size of the tree released is an influential factor in the growth of species. The temporality of climate and physiological conditions of each species are influential in the growth. It is evident that the defoliation of certain species is an important factor that limits the growth of the species causing thinning to have a negative response. Background and Objectives: The objective is to analyze the behavior of nine timber species, respective to diametric growth after their liberation. This research aims to answer the following questions: (i) How do the selected tree species react to the liberation? (ii) Can the productivity of the trees (diametric growth) be enhanced by liberation? (iii) Are there other factors that influence the diametric growth of the released trees? Materials and Methods: The study was executed in the “Reserva Biológica San Francisco” were 488 trees were monitored, including nine timber species. Therefore, 197 trees were released (removal of competitors) and 251 trees served as reference. To check whether the initial DBH or other factors, like the selective thinning or climate conditions, determine the diameter growth a linear mixed model GLMM was applied. To adjust the linear mixed model a one-way Anova test was executed. Results: Timber species responded differently to the thinning in comparing to reference trees. Therefore, the species analyzed were separated into three groups (positive, negative, and no response to liberation). Conclusions: Liberation potentiates the growth of certain timber species that do not defoliate and considered semi-tolerant to shade. Precipitation and temperature affect all species, but in the defoliate species, it would not be convenient to release them or at least the evidence of these first three years does not show clear differences with control trees. Increase in trees released are higher in trees of the first two diametric classes in all species, this means that larger trees (i.e., older) release does not affect them in a positive way so release should occur in the youngest trees.

The paper presents the results of high precision control survey carried out in the underground mining of Oyu Tolgoi project using terrestrial laser scanning technology. The purpose of the measurements is to ensure the heading, total length and volume of the penetration and excavation works are being implementing in accordance with the planned and designed dimensions. We established a network of 18 reference points in the tunnel of the selected underground level which were repeatedly measured 4 times by two round readings of the Trimble S7 tacheometry and processed by using the Trimble Business Center software. All points except the one was within the permissible error. Based on these points the excavation length and volumes were determined using the Trimble SX12 laser scanner. The difference between the planned work quantity provided by the Oyu Tolgoi project and the actual values measured by the laser scanning was calculated using the comparative method. The TLS partial control measurements in the excavations made through the ore bodies revealed the length of 20285.72 m and volume of 441128.80 m3 for underground 7 mine levels while their project values were 16158.26 m length and 422837.50 m3 volume, respectively.

Due to satisfactory mechanical properties, low specific weight and other advantages, a substantial utilization of laminated structural composites in many components and equipments of several industry sectors, especially in the past two decades, has been made. This class of materials has a good potential to be an important ally to support scientists and engineers with the main current world challenge: an energy transition process that must occur with sustainability, eco-friendly materials and based on an efficient reduction of greenhouse gas emissions. In this context, a microanalysis (scale length: 10μm to 1mm) of mechanical behavior that considers the multiphase characteristics, at leastwise a matrix and a reinforcement phase, of this kind of composites must be explored, i. e., a heterogeneous material is assumed to predict, for example, the effective tensors of stiffness or compliance by a homogenization process, modeling to damage analyses, studies about progressive delamination and other specific aspects of a composite can be previously investigated using micromechanical approaches. Therefore, the understanding of fundamental micromechanics as well as some advanced models are essential to apply these materials in structural industry components. In this sense, this systematic literature review is designed to investigate the main basic and advanced models of laminated composites micromechanics and using this overall study, have been developed, in the end, an analysis of research trends to the topic, in which, lines to future researches are indicated.

This research ventures into the critical public health challenge of childhood obesity by exploring the dynamic interplay between psychological well-being and Body Mass Index (BMI) throughout various developmental stages of childhood. It delves into how emotional regulation, attachment dynamics, and social relationships correlate with obesity from early childhood to adolescence. Highlighting key findings, such as the negative correlation between psychological resilience and higher BMI in young children, the impact of social relationships on obesity risk during pre-adolescence, and the link between adaptive emotional strategies and higher BMI in adolescents, this study brings to the fore the nuanced relationship between psychological factors and obesity. Utilizing the interdisciplinary process of bioinformatics, this research synergizes psychometric and biomedical data to unearth psychological markers critical for crafting targeted, age-appropriate interventions. This study advocates for a holistic healthcare approach, emphasizing the integration of psychological support within obesity prevention and management strategies, thereby underscoring the indispensable role of psychological factors in the fight against childhood obesity. The application of bioinformatics methods to analyze complex datasets demonstrates how collaboration across medical specialties can enrich our understanding and response to childhood obesity, contributing significantly to the development of comprehensive, bioinformatics-enhanced healthcare solutions.

There are many modern and traditional methods in valuing the performance of the company among them EVA, CVA are modern methods where as EPS, ROI, ROE etc. are some of the traditional methods. modern and traditional methods are not only used to check the performance of a company but it also used in investment decisions by the investors. Stern Stewart, managing partner of M/s Stern Stewart & Co. introduced a modified concept of economic profit in 1990 in the name of Economic Value Added (EVA) as measure of business performance and CVA is only a cash consideration in EVA. In this paper an attempt is made to study which method is used by the investors while taking the investment decisions i.e. traditional methods are modern methods. 100 respondents (Investors) are questioned and collected their views, we are assuming that there is no impact of traditional or modern methods while taking investment decisions by the investors.

Unmanned aerial vehicle (UAV) systems are widely used in many forest-related fields owing to their cost-intensive and precise surveying technology. This study classified erosion susceptibility (ES) in a timber harvesting area using machine learning (ML) and statistical approaches. In dataset generation for the training and testing process, the digital surface model (DSM) of difference (DoD) for July–June was utilized as a dependent variable, and six terrain maps of the DSM for June were used as independent variables. The ES threshold was set at 5 cm for the binary classification of ES pixels while processing using ML (e.g., random forest and extra gradient boost [XGB]) and statistical (e.g., logistic regression) algorithms for model development. The overall accuracy (OA), receiver operating characteristics, and area under the curve (AUC) were calculated for model accuracy and validation. Although the AUC of all models did not appear acceptable (AUC > 0.7), the XGB model showed the best performance regarding time duration, OA, and AUC by 2 h, 64%, and 0.63, respectively. Despite the low AUC and accuracy of the XGB model, the wheel tracks and edges of the operation road were determined to be susceptible areas in the ES map of the XGB.

One of the most crucial elements in deeply understanding humans on a psychological level is manifested through facial expressions. The analysis of a human behavior can be informed by their facial expressions, making it essential to employ indicators such as expression (Expr), valence-arousal (VA), and action units (AU). In this paper, we introduce the method proposed in the Challenge of the 6th Workshop and Competition on Affective Behavior Analysis in-the-wild (ABAW) at CVPR 2024. Our proposed method utilizes the multi-modal Aff-wild2 dataset, which is splitted into spatial and audio modalities. For the spatial data, we extract features using a SimMiM model that was pre-trained on a diverse set of facial expression data. For the audio data, we extract features using a WAV2VEC model. To fusion the extracted spatial and audio features, we employed the cascaded cross-attention mechanism of a transformer.

Hearing loss that arises from various causes at different stages of life has a direct impact on individuals' physical and mental well-being. This paper aimed to evaluate the employment, workplace adaptation, productivity, and professional success of individuals who have hearing loss and whose hearing loss is corrected with a cochlear implant. In this cross-sectional study, the data was collected between November 2022 and March 2023 with the participation of individuals with cochlear implants living in several settlements in all regions of Türkiye. A total of 142 participants with severe hearing loss who were corrected with a cochlear implant were included in this study. The survey method was used to collect data for the study. The questionnaire consisted of 32 questions and was distributed to the participants online. In the first part of the questionnaire (1-10 questions), general characteristics of implant patients were investigated. In the second part (11-32 questions), the positive or negative effects of implantation on the work life of the participants were evaluated. Almost half of the research group (49.3%, n = 70) consisted of women, and the mean age of the participants was determined to be 35.8 ± 14.8. There was no significant difference between gender, educational status, implanted side, working time, working style (physical, desk), and factors affecting work life (p > 0.05). Professional satisfaction and success at work increased significantly more in those with acquired hearing loss (p = 0.010). Post-implantation workplace compliance, success, and productivity were found to be higher in those with acquired hearing loss (p = 0.013). It was observed that hearing loss had a greater negative impact on the work life of married people (p = 0.006). Cochlear implantation greatly enhances workplace satisfaction, increases self-confidence, and has a positive impact on the future of profoundly deaf individuals.

In the last two decades, the application of composite structures in many industrial sectors has been made progressively. For the current major scientific and technological challenge, the energy transition with sustainable and eco-friendly initiatives, the polymer matrix laminated composites have been revealed as an excellent alternative for the renewable energy sector. In this context, the knowledge about mechanical behavior of multiphase materials is required. Then, researches related to macro, mesomechanical and multiscale approaches are very important to improve accuracy of the models to predict effective mechanical properties and to develop a better understanding about complex phenomena such as progressive damage, creep and fatigue. Due to theses needs, this research is a synthesis of fundamentals and advanced topics concerning to global modeling of laminated composite structures, layerwise analyzes and micro-macromechanical models, in which mainly fiber, matrix, interface and damage characteristics are studied and used in the macroscale approach. At the end of this study, some final remarks and a trend analysis are proposed based on literature consulted, in other words, expectations for the future works are made by the authors.

Mass timber products, together with careful forestry management, could help decarbonize the construction industry. These products must be long-lasting, to safely store atmospheric carbon for decades or centuries, and multi-functional, to displace materials and equipment that are emissions-intensive. This paper shows how to optimize mass timber panels as heat-exchangers, suggesting how to eliminate insulation while simplifying HVAC systems. Test panels measured the heat-exchange in steady and transient conditions, when the ventilation was driven by a fan or by thermal buoyancy. The total heatexchange was predicted accurately by theory in all cases. Further investigation is needed to understand the possible heat-recovery effects at the exterior surface.

This study aimed to investigate the knowledge of patients with hypertension about their condition, adherence to antihypertensive medication, and the factors influencing it. A cross-sectional study was conducted in two cardiology outpatient clinics of two tertiary hospitals, in Greece. The study included 188 patients diagnosed with hypertension. The patient’s knowledge about their disease and adherence to medication were assessed by using the HK-LS and A-14 scales, respectively. Patients had sufficient knowledge levels about their disease, but significantly low levels of adherence to medication. Patients with higher knowledge levels were more adherent to medications [r(188) = 0.885, p < 0.001]. By using multivariate analysis, higher age (p = 0.018), residence in a more populous area (p = 0.041), more years with the disease (p = 0.012), and a lower number of medications (p = 0.03) were associated with higher levels of knowledge. Conversely, younger age (p = 0.036), lower educational levels (p = 0.048), fewer years with the disease (p = 0.001), and a higher number of medications (p = 0.003) were associated with lower adherence to medication. The Greek patients' hypertension knowledge was sufficient, however, adherence to medication was significantly low. Healthcare managers could utilize our findings to design targeted interventions for improving adherence to medication for these patients.

Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

The Work Ability Index (WAI) is the most widely used questionnaire for the self-assessment of working ability. Because of its different applications, shorter versions, and widespread use in healthcare activities, it is worthwhile assessing its characteristics. The WAI was distributed online among the workers of a healthcare company; the results were compared with data contained in the workers' personal health records and with absence registers. 340 out of 575 workers (59.1%) participated; 6.5% of them reported poor work ability. Exploratory factor analysis indicated that the one-factor version best described the characteristics of the WAI. The scores of the complete WAI, the shorter form without the list of diseases, and the minimal one-item version (WAS) had equal distribution and were significantly correlated. The WAI score was inversely related to age and significantly lower in women than in men, but it was higher in night workers than in colleagues due to the probable effect of selective factors. The WAI score was also correlated with absenteeism, but no differences were found between males and females in the average number of absences, suggesting that cultural or emotional factors influence the self-rating of the WAI. Workers tended to overreport illnesses in the online survey compared to data collected during occupational health checks. Musculoskeletal disorders were the most frequently reported illnesses (53%). Psychiatric illnesses affected 21% of workers and had the greatest impact on work ability. Multilevel ergonomic and human factor intervention seems to be needed to recover the working capacity of healthcare workers.

Developmental, clinical, and epidemiological research have demonstrated the salience of perceived racial discrimination (PRD) as a contributor to negative mental health outcomes in adolescence. This article summarizes secondary analyses of cross-sectional data from a large-scale youth survey within a predominantly rural state to estimate the prevalence and strength of association between PRD and serious psychological distress, suicidal ideation, and prior suicidal attempts. Data from 93,812 students enrolled in Grades 6, 8, 10, and 12 within 129 school districts across Kentucky were examined to determine prevalence rates for subgroups within the cohort. Logistic regression analyses assessed differences and established comparative strength of association among these variables for racial/ethnic subgroups. PRD was self-reported at high rates across several demographic subgroups and was most evident among Black (24.5%) and Asian (22.1%) students. Multiracial students experienced the highest rates of both SPD and suicidality. Both for the entire cohort and for each racial/ethnic subgroup, PRD was significantly associated with increased likelihood of negative mental health outcomes, although the strength of these associations varied across subgroups and developmental levels. Implications for early intervention and prevention are discussed.

Agroforestry systems with multipurpose tree species, for the double production of timber and fruit, along with the intercropping with herbaceous crops, can be fundamental land use systems for multiple ecosystems services. Research was conducted in Italy, for one growing season, in 18 years old agroforestry experimental plots with common walnut (Juglans regia L.) trees, according to the previous agroforestry management (AFM) since tree planting. The aim is i) estimating trees growth and herbaceous yield in relation to increasing tree size, especially referring to the trees basal area (G); ii) evaluating the role of nut production as additional product to timber and food crops. Observations were run on tree growth and leaf phenology, total light transmittance (TTL) below tree canopy and hay yield with and without walnut intercropping. Nut yield was estimated from available literature and associated to G. At the end of the study year, representing two third of trees rotation, their height varied between 10 and 11 m, with much larger variation for tree diameter between 17 and 22 cm, according to the previous AFM, including tree mulching with plastic film. Hay yield varied between 4.5 and 3 Mg ha year-1 outside and under tree canopy, respectively. Negative regression were determined for G and TTL, and G and hay yield, with an annual reduction of 5% per G unit. Simulations were run on hay and nut yield, using G as main input parameter. The work points out the following key findings: i) the usefulness of plastic mulching, at tree planting, to increase the long-term timber productivity of the trees intercropped with herbaceous crops; ii) the negative linear relationship between hay productivity and walnut trees G; iii) G influences, in positive way, more markedly nut than hay yield. Suggestions are given on the optimum tree planting spacing and AFM for balancing timber, nut and hay yields.

The dispersal potential of crown-of-thorns starfish (CoTS) larvae is important in understanding both the initiation and spread of population outbreaks, and is fundamentally dependent upon how long larvae can persist while still retaining the capacity to settle. This study quantified variation in larval survivorship and settlement rates for CoTS maintained at three different chlorophyll concentrations (0.1, 1.0 or 10.0 µg.L^-1), achieved by varying densities of single-celled flagellate phytoplankton, Proteomonas sulcata. Based on the larval starvation hypothesis we expected that low to moderate algal concentrations would significantly constrain both survival and settlement. CoTS larvae were successfully maintained for up to 50 days post-fertilization, but larval survival differed significantly between treatments. Survival was greatest at intermediate (1.0 µg.L^-1) chlorophyll concentrations, and lowest at highest (10.0 µg.L^-1) chlorophyll concentrations. Rates of settlement were also highest at intermediate (1.0 µg.L^-1) chlorophyll concentrations and peaked at 22 days post-fertilization. Peak settlement was delayed at low chlorophyll concentrations, probably reflective of delayed development, but there was no evidence of accelerated development at high chlorophyll concentrations. CoTS larvae were capable of settling 17-43 days post-fertilization, but under optimum conditions with intermediate chlorophyll concentrations, peak settlement occurred at 22 days post-fertilization. Moderate increases in nutrient concentrations and algal densities may increase the number of CoTS that effectively settle, but are unlikely to influence dispersal dynamics.

Heart myocardia are critical to the facilitation of heart pumping and blood circulating around the body. The biaxial mechanical testing of the Left Ventricle (RV) is utilised to build the computa-tional model of the whole heart with little importance given to the unique mechanical properties of Right Ventricle (RV) and Mid-wall (MDW). Most of those studies focussed on the LV of the heart, and then apply the obtained characteristics with a few modifications to the right side of the heart. However, that view has been contested over time with the realisation that the right side of the heart possesses its own unique mechanical properties that are widely distinct from that of the left side of the heart. This paper is aimed at reporting and evaluating the passive mechanical property dif-ferences in the three main walls of the rat heart based on biaxial tensile test data. Fifteen mature Wistar rats weighing 225 ± 25 g were euthanised by inhalation of 5 % halothane. The hearts were excised after which all the top chambers comprising the two atria, pulmonary and vena cava trunks, aorta and valves are all dissected out. Then 5 x 5 mm sections from the middle of each wall were carefully dissected with a surgical knife to avoid over-prestraining the specimens. The specimens were subjected tensile test. The elastic moduli, peak stresses in the toe region and stresses at 40 % strain, anisotropy indices as well as the stored strain energy in the toe and linear region up to 40 % strain are used for statistical significance tests. The following are the main findings of this study: (1) LV and MDW tissues have relatively shorter toe regions of 10 - 15 % strain as compared to RV tissue whose toe region extends up to twice as much as that (2) LV tissues have higher strain energy storage in the linear region despite being lower in stiffness than the RV (3) the MDW has the highest strain energy storage along both directions which might be directly related to its high level of anisotropy. These findings, though for a specific animal species at similar age and around the same body mass, emphasize the importance of application of wall specific material parameters to obtain accurate ventricular hyperelastic models. The findings further enhance our understanding of the desired mechanical behaviour of the different ventricle walls.

BackgroundAdvanced radiological stage of knee osteoarthritis (OA) and obesity are predictive of poorer and shorter response to viscosupplementation, but very few is known regarding the impact of other factors such as sport practice, comorbidities or anatomical features of OA. ObjectivesTo investigate the patient’s and OA characteristics associated with the duration of effectiveness (DE) of viscosupplementation in patients with knee OA.MethodsCross-sectional single center trial in patients with knee OA treated with intra-articular (IA) hyaluronic acid (HA) injection(s) within the previous 3 years. The investigator collected demographic and radiographic data (Kellgren grade, involved knee compartments), dosing regimen (single or repeat injections), presence and volume of joint effusion, previous or concomitant IA corticosteroid injection, number of previous viscosupplémentations and the comorbidities. The patient completed a questionnaire including the self-assessment of DE (number of weeks during which viscosupplementation was effective on symptoms), the activity level (sedentary, active, athletic), the level of sport activity (light, moderate or intensive). Predictors of DE were studied in univariate and multivariate analyses ResultsOne hundred five patients (149 knees) were analyzed (62% women, mean age 66.1 ± 13.2 years, mean BMI 27.5 ± 7.5 kg/m²). The mean DE was 48.2 + 24.8 weeks. In a bivariate analysis, the predictors of a shorter with DE were BMI >27.5kg/m2, more than 3 previous viscosupplémentations, Kellgren grade 4, sedentary patients, and more than 1 affected compartment. In the multivariate analysis, 4 independent factors remained associated with a shorter DE: BMI >27.5 kg/m2, knee multi-compartment damage, number of viscosupplements >3, sedentary lifestyle. A statistically significant association between a longer DE and treated arterial hypertension was found suggesting a beneficial effect of certain antihypertensive drugs. ConclusionThe study confirms the harmful influence of an increased BMI, It also shows that viscosupplementation is more effective in unicompartmental OA. Other points worth highlighting are the reduction in the duration of efficacy with repeated cycles of injections and the benefit of a regular physical activity.

The most widespread intracellular bacteria in the animal kingdom are maternally-inherited endosymbionts of the genus Wolbachia. Their prevalence in arthropods and nematodes worldwide and a stunning arsenal of parasitic and mutualistic adaptations make these bacteria a biological archetype for basic studies of symbiosis and applied outcomes for curbing human and agricultural diseases. Here, we conduct a summative, centennial analysis of living in the Wolbachia world. We synthesize literature on Wolbachia’s host range, phylogenetic diversity, genomics, cell biology, and applications to filarial, arboviral, and agricultural diseases. We also review the mobilome of Wolbachia including phage WO and its essentiality to hallmark phenotypes in arthropods. Finally, the Wolbachia system is an exemplar for discovery-based science education using biodiversity, biotechnology, and bioinformatics lessons. As we approach a century of Wolbachia research, applications, and education, the interdisciplinary science and knowledge from this symbiosis stand as a model for consolidating and teaching the integrative rules of endosymbiotic life.

Recent studies have emphasized the influence of resettlement factors on the mental health of refugees resettling in developed countries. However, little research has addressed gender differences in the nature and influence of resettlement stressors and sources of resilience. We address this gap in knowledge by investigating how gender moderates and mediates the influence of several sources of distress and resilience among 259 Afghan refugees residing in northern California. Gender moderated the effects of four factors on levels of distress. Intimate and extended family ties have little correlation with men’s distress levels, but are strongly associated with lower distress for women. English ability is positively associated with lower distress for women, but not men. In terms of gender ideology, traditionally oriented women and egalitarian men have lower levels of distress. And experiencing greater dissonant acculturation increases distress for men, but not women. The influence of gender interaction terms is substantial and patterns may reflect difficulty adapting to a different gender order. Future studies of similar populations should investigate gender differences in sources of distress and resilience, and efforts to assist new arrivals might inform them of changes in gender roles they may experience, and facilitate opportunities to renegotiate gender roles.

Globally, non-timber forest products (NTFPs) continue to contribute vastly to addressing the food, poverty reduction, income, and livelihood requirements of people in rural areas. However, as at now, there is no specific existing data highlighting periodic contributions of NTFPs to the economy of the Eastern region and the country. The study analyses the contribution of NTFPs towards economic development in the Eastern region and the achievement of SDGs in Ghana. Through Focus Group Discussions and qualitative analysis, it was concluded that NTFPs contribute immensely towards the economic development of the Eastern region and the country through employment and direct taxes. Ultimately, it is evident from the study that the destruction of the Atiwa forest reserve for the purpose of bauxite mining will widely hinder the country’s achievement of the SDGs. Also, the study found out that residents will continue to exploit forest resources if the core concerns of institutional deficiencies and rural poverty are not addressed. To curb this situation, there should be sustainable, regulated, and authorized harvesting of NTFPs/NWFPs, community/user empowerment, sectoral education and training programmes, etc. Even though these are common solutions, the study found them extremely rare in the study area.

Background: Hashimoto’s thyroiditis (HT) is an autoimmune disease that progressively leads to thyroid gland destruction and hypothyroidism. Patients produce antibodies against two thyroid-specific antigens: thyroglobulin and thyroid peroxidase. As a result of the abnormal amount of thyroid hormone produced and its autoimmune etiology, patients with HT display a higher frequency of either autoimmune or non-autoimmune dermatological disorders. On ultrasound examination, HT can be detected by observing an enlarged thyroid gland with hypoechoic parenchymal regions or by observing a small gland indicating atrophy and diffusely heterogeneous parenchyma. Changes in the parenchymal vascularity can be observed as decreased or increased levels of vascularization. Objective: This study aimed to analyze the role of clinical data and ultrasound evaluation of patients with HT in suggesting an association with dermatological disorders. Patients and methods: Complete dermatological and endocrinological assessments as well as ultrasonography of the thyroid and lymphnodes were performed in HT patients. Results: The data obtained showed that a family history of thyroid disease, increased diameter of the inferior thyroid artery, and the presence of cervical lymphadenopathy were more frequent in the group of patients with dermatological diseases. Taken together, our results suggest the usefulness of ultrasound in determining a possible association between HT and dermatological disorders.

This work deals with finding out whether the heart rate values of operators of forwarding machines during the work shift are influenced by the individual activities that the operator has to perform during timber skidding, or by the operators themselves. Furthermore, the work deals with determining the difficulty of individual activities in terms of physical load. For this purpose, the work shift of operators carrying out timber skidding was divided into individual activities: Driving, Maintenance, Forwarding, Break. During these work activities, the heart rate of each operator was taken for subsequent evaluation. The results show that the highest pulse rates of the operators were achieved during the Maintenance of the entrusted machine, while the highest pulse fluctuations in the operators were recorded during Forwarding. As part of this activity, the highest heart rate of the entire measurement process was recorded (132.0000 bpm), but also the lowest (42.0000 bpm). Furthermore, it was proven that both the operator and the activity he performs affect the pulse rate. The activities themselves did not differ from each other in only one of the six cases of comparison. Specifically, it was Driving and Forwarding.

Building carbon footprint analysis is a key instrument for assessing the impact of different constructions on climate change. Several standards and methodologies are available to calculate the footprint of buildings, including standards and norms, life cycle assessment (LCA), and dedicated software tools. The use of BIM software for these calculations is both scientifically justified and very practical. This scientific publication focusses on the application of a BIM-based research methodology for the analysis of the carbon footprint of a single-family house. The research process included the following steps: (i) design of a single-family house with timber frame construction using Archicad BIM software, (ii) simulation of the building energy performance using the EcoDesigner Star plug-in, (iii) life cycle assessment (LCA) using the plug-in for Archicad, (iv) preparation of a second model with traditional masonry construction for comparison, and (v) comparative analysis of the single-family house models with timber frame and masonry construction. Analysis of the results highlights significant differences in CO2e emissions between masonry and timber buildings and the varying impact of individual elements on the total CO2e emissions of the buildings studied. These findings are relevant for future work on sustainable building design and construction, which aims to minimise negative environmental impacts. The goal of minimising the cumulative carbon footprint of buildings is critical to achieving the Sustainable Development Goals and combating climate change.

Purinergic receptors (P2X) are ATP-gated ion channels with an elusive role in the CNS. While the P2X2 and P2X4 subtypes are widely expressed in most neurons (i.e. at the edge of the postsynaptic densities of excitatory synapses), the direct contribution of P2X to synaptic transmission is uncertain. Several P2X have been shown to participate in receptor cross-talk: an interaction where one receptor (e.g. P2X2) influences the activity of another (e.g. GABA or AMPA receptors.) In this study, we tested for interactions between P2X2 or P2X4 and N-methyl-D-aspartate receptors (NMDARs). Using two-electrode voltage-clamp electrophysiology experiments in X. laevis oocytes, we demonstrate that both P2X2 and P2X4 interact with NMDARs in an inhibitory manner. When investigating the molecular domains responsible for this phenomenon, we found that the P2X2 c-terminus (CT) could interfere with P2X2 and P2X4 interactions with NMDARs. We also report that 11 distal CT residues on the P2X4 facilitate the P2X4-NMDAR interaction, and that a peptide consisting of these P2X4 CT residues (11C) can disrupt the interaction between NMDARs and P2X2 or P2X4. Collectively, these results provide new evidence for the modulatory nature of P2X2 and P2X4, suggesting they might play a more nuanced role in the CNS.

Telehealth is the delivery of many health care services and technologies to individuals at different geographical areas and is categorized as asynchronously or synchronously. The coronavirus disease 2019 (COVID-19) pandemic has caused major disruptions in health care delivery to breast cancer (BCa) patients and there is increasing demand for telehealth services. Globally, telehealth has become an essential means of communication between patient and health care provider. The application of telehealth to the treatment of BCa patients is evolving and increasingly research has demonstrated its feasibility and effectiveness in improving clinical, psychological and social outcomes. Two areas of telehealth that have significantly grown in the past decade and particularly since the beginning of the COVID-19 pandemic are telerehabilitation and teleoncology. There two technological systems provides opportunities at every stage of the cancer care continuum for BCa patients. We conducted a systematic literature review that examined the use of telehealth services via its various modes of delivery among BCa patients particularly in areas of screening, diagnosis, treatment modalities, as well as satisfaction among patients and health care professionals. The advantages of telehealth models of service and delivery challenges in delivery to patients in remote arears are discussed.

Variable and sometimes contrasting effects of using artificial rhizobium inocula to increase grain legume performance have been reported. The objectives of this systematic review and meta-analysis were therefore to (i) estimate the overall effect of rhizobium inocula on grain yield and protein content and (ii) identify potential confounding factors that explain the observed variation. A web of Science database literature search was carried out in 2016. Data from all field experiments, greenhouse and pot experiments that compared grain yields and protein contents in Rhizobium/Bradyrhizobium-inoculated with non-inoculated control crops were extracted and analyzed using previously described unweighted and weighted meta-analysis protocols. GRADE assessments of the strength of evidence of results from the weighted meta-analyses were carried which included an assessment of the risk of publication bias. Results: For unweighted meta-analyses we identified eligible data in 236 and 36 studies for grain yield and protein content respectively. For weighted meta-analyses we identified eligible data in 92 and 8 studies for grain yield and protein content respectively. Rhizobium inoculation was found to (i) significantly increase grain yield in both the unweighted (mean percent difference: 41%, 95%CI 36,46, p<0.0001) and weighted meta-analysis (Standardized mean difference: 1.56, 95%CI 1.26,1.87, p<0.0001) and (ii) significantly increase protein content in the unweighted meta-analysis (mean percent difference: 11%, 95%CI 5,18, p<0.0001), but not the weighed meta-analyses which only detected a trend (0.1>p>0.05) towards higher protein content in inoculated grain legume crops. Multi-level model-based weighted meta-analyses suggest that the (i) type of experiment, (ii) type of fertilizer used in experiments, (iii) grain legume type/species and (iv) the country in which experiments were carried out, were confounding factors. The main limitation of the evidence is that a large number of publications did not report measures of variation and could therefore not be included in the more scientifically sound weighted meta-analyses. However based on the large evidence-base available for grain yield it can be concluded that overall Bradyrhizobium/Rhizobium seed inoculation results can increase grain yield by ~40% compared with non-inoculated grain legume crops.

Non-timber forest products (NTFP) have contributed in various ways to the living, livelihoods, and trading of households and communities who live in rural and urban areas all over the world. This paper analyses the value chain of Jiaogulan (Gynostemma pentaphyllum) in the Cao Bang Geopark, Vietnam. 106 actors were surveyed using a semi-structured questionnaire: experts (agricultural extension officers, farmers' associations), harvesters, traders, primary processors, processors, distributors, and consumers. The results show that a map of Jiaogulan value chain, value added of households in main market channels, and impact of value added and distribution of Jiaogulan products on household income.

The overexploitation of forest resources in the charcoal production basin of the city of Lubum-bashi (DR Congo) is reducing the resilience of miombo woodlands and threatening the survival of the riparian as well as urban human populations that depend on it. We assessed the socio-economic value and availability of plant-based non-timber forest products NTFPs in the rural area of Lubumbashi through ethnobotanical (100 respondents) and socio-economic (90 respondents) interviews, supplemented with floristic inventories, in two village areas selected on the basis of the level of forest degradation. The results show that 60 woody species, including 46 in the degraded forest (Maksem) and 53 in the intact forest (Mwawa), belonging to 22 families are used as sources of NTFPs in both villages. Among these species, 25 are considered priority species. NTFPs are collected for various purposes, including handcrafting, hut building, and traditional medicine. Moreover, the ethnobotanical lists reveal a similarity of almost 75%, indicating that both local communities surveyed use the same species for collecting plant-based NTFPs, despite differences in the level of degradation of the miombo woodlands in the two corresponding study areas. However, the plant-based NTFPs that are collected from miombo woodlands and traded in the urban markets have significant economic value, which ranges from 0.5 to 14.58 USD per kg depending on the species and uses. NTFPs used for handicraft purposes have a higher economic value than those used for other purposes. However, the sustainability of this activity is threatened due to unsustainable harvesting practices that include stem slashing, root digging, and bark peeling of woody species. Consequently, there is a low availability of plant-based NTFPs, particularly in the village area where forest degradation is more advanced. It is imperative that policies for monitoring and regulation of harvesting, and promoting sustainable management of communities’ plant-based NTFPs priority, be undertaken to maintain their resilience.

AbstractBackground: In digitalization era, health care system was conditioned with the health worker’s ability to adapt media of digital technology. Digital technology media was used to strengthening and fasted the health care for patient and community. Aims: This study aimed to explore the accurate information of health professional utilization digital technology during doing the job at the health facilities in Timor-Leste. Methods: This study was used correctional study with 56 respondents was participated in the study. Was collected the data from 1 to 30 February 2023. Was used questioner of google form based for data collection. Data collection was distributed via online with google form to social media as WhatsApp’s, email and face book and twitter to completed by respondents. The inclusive Criteria are: health professional living in Timor-Leste, to able response the questioner. Was used descriptive analysis in this study. Finding: This study was indicated that majority of health professional was participated in the study as 54,2% man then women have 45,8%. About 100% health professional used hand phone to facilitate their daily activities including related with their work activities. Other side indicated in digital technology tools use are able to use Microsoft word is 78,3%, able to use Microsoft Excel is 76,7% and able to use Power Point is 81,7%. E-mail use about 89,2%, WhatsApp’s use 81,7%, About 74,2% was used zoom/webinars/Google meet application, about 72,5% sad that they were used computer in the work place until now. Around 96.4% need to improve or deepen their knowledge and skills in using ICT in the future to facilitate they are activity. Conclusion: Majority of health professional in Timor-Leste was used the computer, internet, hand phone in daily activities. Majority need to gate the training to improve their knowledge, attitude and psychomotor in the future.

Background: The COVID-19 outbreak has accelerated the huge difference between medical care and disease prevention in Chinese medical institutions. This study aimed to investigated the relationship between the symbiotic units, environments, models, and effects of the integration of medical and disease prevention. Methods: This cross-sectional study involved 762 employees of public hospitals in 11 cities in Zhejiang Province by random stratified sampling. We analyzed the influence paths of elements in the mechanism of integration of medical and disease prevention and the mediating effect of symbiotic models among symbiotic units, symbiotic environments, and effects for on this integration. Results: The path coefficient of symbiotic unit on the symbiosis model was 0.46 (p<.001), the path coefficient of symbiotic environment on symbiosis model was 0.52 (p<.001). The path coefficient of the symbiotic unit and environment was 0.91 (p<.001). The symbiotic models exhibited a partial mediation effect between symbiotic units and the effect of this integration. Sobel test = 3.27, β = 0.152, and the mediating effect accounted for 34.6%. Conclusions: It is suggested that Health policy-makers and public hospital managers should provide sufficient symbiotic units, establish collaborative symbiotic models, and improve the effects of integration of medical and disease prevention in public hospitals.

In the clock network design, the trade-off between power consumption and timing closure is an important and difficult issue. To achieve this target, a hybrid clock network architecture that combines both clock tree and clock mesh seems to be a promising solution. In this paper, we propose a novel clock mesh architecture – cross-mesh, with the average dispersion of the overall driving force, our methodology creates small non-zero skew clock trees. In addition, we integrate clock gating and register clustering techniques to further reduce dynamic power consumption. The proposed algorithms have four stages: cross-mesh planning, register clustering, mesh line connecting, and load balancing. Experimental results show that our methodology and algorithms get feasible solution effectively and improve both power consumption and clock skew simultaneously.

Respiratory syncytial virus (RSV) is associated with adverse outcomes among immunocompromised patients. Inhaled ribavirin has been shown to improve mortality rates. The Small-Particle Aerosol Generator delivery system (SPAG-2) is the only FDA-cleared device to deliver inhaled ribavirin. However, it is difficult to set up and maintain. We developed a method for delivery of this medication using the vibrating mesh nebulizer (Aerogen®). We did not observe any adverse events with this method.

The mutation databases have vital importance in detecting genetic mutation and their corresponding phenotypes. The emergence of next generation sequencing genetic technologies has accelerated this process, and the growth of genetic disease identification has created a need for quality control and documentation of mutation-related information. Ethnic-specific mutation databases offer valuable information for researchers, and the article evaluates the homogeneity and effectiveness of these databases. The aim to raise awareness of NEMDBs to healthcare professionals, the general public, and researchers studying genetic disorders. The article also recommendations to improve the effectiveness of these databases.

As digitalization expands across all sectors, the economic toll of software defects on the U.S. economy reaches up to $2.41 trillion annually. High-profile incidents like the Boeing 787-Max 8 crash have shown the devastating potential of these defects, highlighting the critical importance of software testing within quality assurance frameworks. However, due to its complexity and resource intensity, the exhaustive nature of comprehensive testing often surpasses budget constraints. This research utilizes a machine learning (ML) model to enhance software testing decisions by pinpointing areas most susceptible to defects and optimizing scarce resource allocation. Previous studies have shown promising results using cost-sensitive training to refine ML models, improving predictive accuracy by reducing false negatives through addressing class imbalances in defect prediction datasets. This approach facilitates more targeted and effective testing efforts. Nevertheless, the generalizability of these models across different projects (cross-project) and programming languages (cross-language) remained untested. This study validates the model's applicability across diverse development environments by integrating various datasets from distinct projects into a unified, using a more interpretable ML approach. The results demonstrate that ML can support software testing decisions, enabling teams to identify up to seven times more defective modules with the same testing effort as a benchmark.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

OSI model used to be common network model for years. In the case of ad hoc networks with dynamic topology and difficult radio communications conditions, gradual departure is happening from the classical kind of OSI network model with a clear delineation of layers (physical, channel, network, transport, application) to the cross-layer approach. The layers of the network model in ad hoc networks strongly influence each other. Thus, the cross-layer approach can improve the performance of an ad hoc network by jointly developing protocols using interaction and collaborative optimisation of multiple layers. The existing cross-layer methods classification is too complicated, because it’s based on the whole manifold of network model layers combinations, regardless their importance. In this work, we review ad hoc networks cross-layer methods, propose the new useful classification of cross-layer methods, and show future research directions in ad hoc networks cross-layer methods development. The proposed classification can help to simplify the goal-oriented cross-layer protocol development.

We study the generalized χ and η cross helicities for non-ideal non-barotropic magnetohydrodynamics (MHD). χ and η, the additional label translation symmetry group, have been used to generalize the cross helicity in ideal flows. Both new helicities are additional topological invariants of ideal MHD. To study there behaviour in non-ideal MHD, we derive the time derivative of both helicities using the non-ideal MHD equations taking viscosity, finite resistivity and heat conduction into account. Physical variables are divided into ideal and non-ideal quantities separately during the mathematical analysis for simplification. The analytical results indicate that χ and η cross helicities are not strict constant of motion in the non-ideal MHD and show the rate of dissipation which is compared to the dissipation of other topological constants of motion.

Zika virus (ZIKV) co-circulates with several closely related flaviviruses which exhibit similar clinical manifestations thus, clinicians rely on molecular and serological techniques for diagnosis. Cross-reactivity of patient specimens to flaviviruses is a significant impediment to serological diagnosis in areas where multiple flaviviruses co-circulate. Furthermore, patient exposure history to any of these viruses could complicate serological response patterns which could result in over and/or underdiagnosis of ZIKV infection. Three strains of ZIKV, dengue serotypes 1-4, West Nile virus, Japanese Encephalitis virus, and Yellow Fever virus were evaluated for neutralizing properties against 3 monoclonal antibodies, 4 ZIKV-naïve patients with flavivirus exposure history, 5 patients with verified ZIKV exposure and unknown flavivirus exposure history, and 5 flavivirus-naive patients with ZIKV-only exposure. Patients naïve for ZIKV exposure effectively neutralized multiple strains of ZIKV. Overall, the prototype ZIKV isolate MR-766 did not behave like the other ZIKV isolated used in this study. MR-766 was neutralized more completely by polyclonal patient serum than recent ZIKV isolates. MR-766 was neutralized better than dengue virus in ZIKV-naïve patients with prior dengue exposure. MR-766 was neutralized significantly less than recent ZIKV isolates when treated with monoclonal antibodies. The data herein show that without RT-PCR, serological diagnosis may not be possible in areas where multiple flaviviruses are endemic.

The satellite Earth observation (EO) sector is burgeoning with hundreds of commercial satellites being launched each year, delivering a rich source of data that could be exploited for societal benefit. Data streams from the growing constellation of commercial satellites are of variable quality, limiting the potential for their combined use in science applications that need long time-series data from multiple sources. The quality of calibration performed on optical sensors onboard many satellite systems is highly variable due to calibration methods, sensor design, mission objective, budget, or other operational constraints. A small number of currently operating well-characterised satellite systems with onboard calibration, such as Landsat-8/9, Sentinel-2, and planned future missions like the NASA Climate Absolute Radiance and Refractivity Observatory (CLARREO) Pathfinder, the European Space Agency (ESA) Traceable Radiometry Underpinning Terrestrial and Helio Studies (TRUTHS), and LIBRA from China, are considered benchmarks for optical data quality due to their traceability to international measurement standards. This paper describes the concept of a space-based transfer calibration radiometer called the Satellite Cross-Calibration Radiometer (SCR) that would enable the calibration parameters from satellites such as Landsat-8/9, Sentinel-2, or other benchmark systems to be transferred to a range of commercial optical EO satellite systems while in orbit. A description of the key characteristics of the SCR to successfully operate in orbit and transfer calibration from Reference systems to Client systems is presented. A system like the SCR in orbit could complement SI-Traceable satellites (SITSats) to improve data quality and consistency and facilitate the interoperable use of data from multiple optical sensor systems for delivering higher returns on the global investment in EO.

Hardy Cross originally proposed a method for analysis of flow in networks of conduits or conductors in 1936. His method was the first really useful engineering method in the field of pipe network calculation. Only electrical analogs of hydraulic networks were used before the Hardy Cross method. A problem with the flow resistance versus the electrical resistance makes these electrical analog methods obsolete. The method by Hardy Cross is taught extensively at faculties and it still remains an important tool for analysis of looped pipe systems. Engineers today mostly use a modified Hardy Cross method which threats the whole looped network of pipes simultaneously (use of these methods without computers is practically impossible). A method from the Russian practice published during 1930s, which is similar to the Hardy Cross method, is described, too. Some notes from the life of Hardy Cross are also shown. Finally, an improved version of the Hardy Cross method, which significantly reduces number of iterations, is presented and discussed. Also we tested multi-point iterative methods which can be used as substitution for the Newton-Raphson approach used by Hardy Cross, but this approach didn’t reduce number of required iterations to reach the final balanced solution. Although, many new models have been developed since the time of Hardy Cross, main purpose of this paper is to illustrate the very beginning of modeling of gas and water pipe networks or ventilation systems.

Platinum and taxane chemotherapy is associated with the risk of hypersensitivity reactions (HSRs), which may require switching to less effective treatments. Desensitization to platinum and taxane HSRs can be used to complete chemotherapy according to the standard regimen. Therefore, we aimed to investigate the current management of HSRs to platinum and/or taxane chemotherapy in patients with gynecologic cancers. We conducted an online cross-sectional survey among gynecological and medical oncologists consisting of 33 questions. A total of 144 respondents completed the survey and 133 respondents were included in the final analysis. Most participants were gynecologic oncologists (43.6%) and medical oncologists (33.8%), and 77.4% (n=103) were involved in chemotherapy treatment. More than 73% of participants experienced >5 HSRs to platinum and taxane per year. Pre-medication and a new attempt with platinum or taxane chemotherapy were used in 84.8% and 92.5% of Grade 1-2 HSR to platinum and taxane, respectively. In contrast, desensitization was used in 49.4% and 41.8% of Grade 3-4 HSR to platinum and taxane, respectively. Most participants strongly emphasized the need to standardize the management of platinum and taxane HSR in gynecologic cancer. Our study showed that HSR in gynecologic cancer is common, but management is variable and the use of desensitization is low. In addition, the need for guidance on the management of platinum- and taxane-induced HSR in gynecologic cancer was highlighted.

Authorities and governmental bodies strongly emphasize the importance of residents preparing for natural disasters, particularly underscoring the significance of readiness for geophysical hazards like earthquakes. In this study, which represents comparative quantitative research, the levels and predictors of the impact on preparedness for earthquake-induced disasters in South-Eastern Europe countries such as Montenegro, North Macedonia, and Serbia are examined. Using the snowball sampling technique (online questionnaire), a survey of 1245 respondents (Montenegro (n = 400), North Macedonia (n = 345), and Serbia (n = 500) was conducted from February 2023 to February 2024. The paper is based on the central hypothesis that the most significant predictor of earthquake preparedness in Montenegro, North Macedonia, and Serbia is age, followed by gender and education. Multivariate regression analysis was used to determine the extent to which five scores of the subscales (household preparedness, community preparedness, disaster preparation, earthquake risk awareness, reinforced house) were associated with seventh demographic and socio-economic variables. In addition to the mentioned analysis, other statistical analyses such as T-test, one-way ANOVA analysis, and Pearson correlation were also utilized. The results indicate that age emerges as a predictor in various aspects of earthquake-induced disaster preparedness and awareness in most models, followed by education. These findings confirm the significance of respondents' age in determining levels of preparedness and earthquake awareness. Overall, in North Macedonia, respondents recorded the highest ratings (M = 3.52) for household preparedness for earthquakes, compared to Montenegro (M = 2.98) and Serbia (M = 3.26), where the lowest ratings were recorded. Research findings, taking into account cultural characteristics, can serve as a basis for the development of targeted interventions, strategies, policies, and programs aimed at improving the level of societal preparedness for earthquake-induced disasters.