Inorganic polymeric materials react slowly at room temperature and as a result usually require high-temperature curing. This study used the Arrhenius equation to analyze the correlation between curing temperature and curing duration during high-temperature curing. The test results show that optimal values exist for each alkali equivalent of the activator (weight ratio of Na2O/glass powder), curing temperature, and curing duration. Extending the curing duration and increasing the curing temperature have positive effects when the alkali equivalent is lower than the optimal value. However, over-curing results in invisible cracking in the specimens. Furthermore, despite exhibiting high strength initially, the strength of specimens gradually diminishes after standing in air. To ensure the durability of glass-based geopolymer, the curing temperature should not exceed 70℃, and the curing duration should be less than one day.

The paper presents the influence of different curing conditions – wet, dry and protection against water evaporation on selected properties of concretes with different amount of recycled concrete aggregate previously subjected to atmospheric CO2 sequestration. Additionally, the eco-efficiency bi and ci indexes as well as eco-durability S-CO2 index were calculated. It was found that dry conditions deteriorate the properties of concrete, especially made of blast furnace slag cement, while protection against evaporation allows to achieve results comparable to wet conditions. Moreover, for series with the highest amount of coarse recycled aggregate and after longer period of curing, the difference between the effects of wet curing and protection against water evaporation disappears. The eco-efficiency and eco-durability indexes approach confirms the beneficial effect of blast-furnace slag cement used as a binder but on condition of proper way of curing.

Atta capiguara is a grass-cutting ant species frequently found in Cerrado biome. However, little is known about the giant nest architecture of this ant. In this study, we investigated the architecture of three A. capiguara nests from the fragment of cerrado in Botucatu, São Paulo, Brazil. Casts were made of the nests by filling them with cement to permit better visualization of internal structures such as chambers and tunnels. After excavation, the depth and dimensions (length, width, and height) of the chambers were measured. The results showed the typical shape of Atta capiguara nests consisting of mounds of loose soil with unique features resembling a conic section. The fungus chambers were found outside the apparent main part of the nest and were spaced apart and distributed laterally at ground level. The waste chambers were located beneath the largest mound of loose soil. Both the fungus and waste chambers exhibited a sectoral distribution. Our study contributes to a better understanding of the so far unknown nest architecture of the grass-cutting ant A. capiguara.

Background: We prepared reference materials of fentanyl and amphetamines in hair, and established methods for the certification of reference materials of fentanyl and amphetamines in hair samples. Methods: Hair samples containing 15 drugs were prepared by immersion method (water-dimethylsulfoxide). On the basis of single-factor experiment, Box-Behnken design-response surface was used to optimize the pre-treatment conditions of samples. In MRM/SIM mode, 15 drugs were quantitatively analyzed by LC-MS/MS and GC-MS/MS methods. Results: The contents of 15 drugs in the mixed hair samples were: 1.050 ng mg-1~7.771 ng mg-1, RSDs<7%(n=11). The results showed that the two analytical methods developed were highly sensitive (LODs as low as 0.05 pg mg-1), reproducible (intra-day and inter-day precision RSDs were<10%) and accurate. F-test was performed on the prepared hair samples and the results showed that the homogeneity of the prepared hair samples was good. Conclusions: The established methods were used for the detection of fentanyl and amphetamine drugs in human hair, with high sensitivity, accuracy and specificity. It can be used as a certified method for the development of fentanyl and amphetamine matrix certified reference materials. The developed hair reference materials are expected to be applied in forensic drug abuse detection and laboratory quality control.

Since Charles Goodyear discovered the sulfur curing of Natural Rubber in 1839, many studies were carried out to understand the mechanism of sulfur curing. Nowadays, the broadly accepted mechanism includes an activated accelerator complex formed by Zinc oxide, stearic acid, accelerators and sulfur. Furthermore, it is also broadly accepted that the coupling of the sulfur to the polymer takes place in the allylic position to the double bond. Modern passenger car tire treads do not contain any longer Natural Rubber but a blend of SSBR and BR, filled with a silica /silane system. Is it possible to transfer all gained knowledge from the Natural Rubber crosslink reaction to such a modern passenger car tire tread formulation or is it required to “re-think” the sulfur curing?

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Research on high-volume fly ash concrete, which utilizes large quantities of fly ash, has been actively conducted to promote resource recycling and reduce carbon dioxide emissions. However, while cement mixed with fly ash exhibits different temperature sensitivities compared to traditional cement, its hydration and mechanical properties vary depending on curing conditions. Despite this, there is a significant gap in research on this topic. In this study, high-volume fly ash concrete was produced with fly ash replacement rates of 35 % and 55 %. Compression strength tests were performed at various curing ages under three different curing temperature conditions, and the results were analyzed. Additionally, an isothermal calorimeter was used to analyze hydration characteristics under different curing conditions. The results indicated that concrete with high fly ash content was more sensitive to curing temperature compared to ordinary Portland cement.

Direct electric curing (EC) is a new green curing method for cement-based materials that improves the early mechanical properties via the uniform high temperature produced by Joule heating. To understand the effects of EC and steam curing (SC) on the mechanical properties and microstructure of cement-based materials, the mortar was cured at different temperature-controlled curing regimes (40°C, 60°C and 80°C). Meanwhile, mechanical properties, hydrate phase and pore structure of specimens were investigated. The energy consumption of two curing methods was compared and analyzed. The results show that the EC specimens have better and more stable growth of mechanical strength. The pore structure of EC specimen is also better than that of SC specimen at different maintenance ages. However, the hydration degree and products of samples cured by EC are similar to that SC samples. The energy consumption of EC is lower than SC. This study provides an important technical support for the EC in the production of energy-saving and high early-strength concrete precast components.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Bismaleimide (BMI) is a high-performance thermosetting resin widely used in the aerospace, automotive, and mechanical and electronics industries due to its chemical and mechanical stability. It also has the capability of being used as an ink in polyjets used for 3D printing evident from thinner mellamide FTIR bands and faster curing rates as observed from TGA-DSC studies.

The agricultural soil maps (ASMs) showing the agricultural land of Poland were prepared in 1:5000 scale in 1960s’ and 1970s’. These maps show land suitability group, soil type and soil texture (ST) to a depth of about 150cm. Nowadays, these maps are being digitalized and might be a basis for the preparation of modern soil maps at local, regional, national and international level. The agreement between the ST of topsoil derived from ASMs and recently evaluated for eleven fields located in three voivodeships (regions) of Poland was studied. The study of soil considered the examination of soil profiles or augerings and laboratory analysis of the ST. The agreement between soil status in the field and according to maps was field-specific. Complete agreement (purity) within the field was assessed for 5-79% of ST classes and for 23-100% of agronomic categories (ACs) – a groupings of similar ST classes. However, the averaged agreement, which treated adjacent ST classes as having partial agreement, varied from 37 to 88% for ST classes and from 61 to 100% for the ACs among studied fields. These results indicate on the variable quality of the information shown on the ASMs and on the necessity of improvement of these maps.

Thromboembolic conditions, such as stroke and myocardial infarction [MI], are the primary causes of mortality globally. High efficiency was demonstrated by fibrinolytic enzymes isolated from microbial sources in dissolving various blood clots. The study aimed to investigate and produce bacterial fibrinolytic enzymes from various Egyptian soil conditions using recombinant DNA technology. Fifty soil samples were examined to determine the production of fibrinolytic enzymes. The plasmin plate technique assessed the thrombolytic activities of the strong fibrinolytic enzyme-producing bacterial isolates. In addition to determining the molecular mass using a mass spectrometer and the western blot method, the activity and thermostability of the enzymes were characterized. An affinity chromatography approach was used to purify the fibrinolytic enzymes. However, bacterial recombinant DNA technology produced the pure bacterial fibrinolytic enzyme. Several dosage formulations for the formulation of fibrinolytic enzymes were tested. By using affinity chromatography and the SDS-PAGE test, the isolated bacterial fibrinolytic enzyme in this investigation was almost 83% pure. Bacillus cereus ATCC 4342 was identified as the predominant bacterial isolate secreting fibrinolytic enzymes. It was discovered that the fibrinolytic enzyme activity of fifty soil samples ranged from 0.167 U/ml to 1.853 U/ml. The extracellular enzyme extracted from Bacillus cereus culture supernatant demonstrated a relatively stable fibrinolytic activity over 18 hours at a pH range of 7.4–10, as well as stability with maximum productivity at 43℃ for over 60 minutes. In this investigation, the enzyme was referred to as Fibrin-proteinase[ FP]. The fibrin clots were directly thrombolyzed by the FP. The calculated values for the specific activity and molecular mass of the FP were approximately 40.71 units/mg of protein and approximately 30 KDa, respectively. It was observed that the presence of Fe+3 marginally boosted protease activity, but the presence of EDTA decreased it. On the other hand, adding monovalent cations like K+1 and Na+1 significantly increased the fibrinolytic activity of FP. The enzyme exhibited activity throughout the temperature range of 20 to 65℃, peaking at 55℃. The ideal range for the generation of protease was 35–43℃ and 8.0–10. The thermostable fibrinolytic enzyme FP, which was isolated from Bacillus cereus ATCC 4342 in various soil environments in Egypt during the current study, was a promising fibrinolytic enzyme because it demonstrated a more extensive and effective fibrinolytic activity and fewer side effects than the fibrinolytic enzymes that are currently available worldwide. It is advised that further research be done on optimizing the right formulation of bacterial fibrinolytic enzymes in the future to help dissolve different types of blood clots and, as a result, lower the high death rate that exists worldwide.

Understanding user challenges with light dosimeters is crucial for designing more acceptable devices and advancing light exposure research. We systematically evaluated the usability and acceptability of the lido (light dosimeter) by 29 participants who wore the dosimeter near the corneal plane of the eye for 5 days. Common reasons for not wearing the dosimeter included exercise, recharging, wet environments, public settings, and discomfort. Despite these issues, participants adhered to using the dosimeter, with high compliance (89% of recording time). Our findings reveal a significant discrepancy between mean melanopic Equivalent Daylight Illuminance (300 lxmEDI) and median values (51 lxmEDI). This discrepancy indicates that, for most of the time, participants experienced significantly lower light levels. Specifically, participants were exposed to light levels above 250 lxmEDI for only 14% of their wearing time. This highlights the need for increased exposure to recommended light levels. In the evening, participants' light exposure was below the recommended 10 lxmEDI for 58% of the wear time, which is in line with the guidelines for reducing light exposure before sleep. This study highlights the critical need for strategies to enhance daily light exposure, aligning better with circadian health recommendations.

This study introduces a novel predictive model for atomization droplet size, developed through comprehensive data collected under elevated temperature and pressure conditions using a twin swirl airblast nozzle. The model, grounded in flow instability theory, has been meticulously parameterized using the Particle Swarm Optimization (PSO) algorithm. Through rigorous analysis, including analysis of variance (ANOVA), the model has demonstrated robust reliability and precision, with a maximum relative error of 19.3% and an average relative error of 6.8%. Compared to the classical atomization model by Rizkalla and Lefebvre, this model leverages theoretical insights and incorporates a range of interacting variables, enhancing its applicability and accuracy. Spearman correlation analysis reveals that air pressure and the air pressure drop ratio significantly negatively impact droplet size, whereas the fuel-air ratio (FAR) shows a positive correlation. Experimental validation at ambient conditions shows that the model is applicable with a reliability threshold of ≥0.13 and highlight the predominance of the pressure swirl mechanism over aerodynamic atomization at higher fuel flow rates (q > 1.25 kg/h). This research effectively bridges theoretical and practical perspectives, offering critical insights for the optimization of airblast nozzle design.

In this research the efficiency of degradation of different organic contaminant classes, including pesticides (tembotrione, clomazone), pharmaceuticals (ciprofloxacin, 17α-ethinyl estradiol) and mycotoxins (zearalenone, deoxynivalenol, fumonisin B1), by subcritical water treatment, was studied in model systems. All experiments were conducted in a house-made batch type pilot reactor. The research was focused on the optimization of the treatment parameters by using moderate treatment conditions. Optimization of the remediation processes of water contaminated with 17α-ethinyl estradiol, tembotrione, clomazone, ciprofloxacin, was conducted by testing different homogeneous and heterogeneous catalysts, as well as different gas atmospheres (nitrogen and carbon-dioxide) for pressurization of the process system. Mycotoxins in water were degraded without catalysts and all experiments were conducted in nitrogen atmosphere. Optimization was conducted by defining the optimal combination of the treatment temperature and time, oriented towards energy saving and minimization of the technical requirements. The degradation efficiency in all tested samples was determined by HPLC analysis.

Three types of the composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, curing process and physical-mechanical properties. In the first type of composites, manganese-zinc ferrite, nickel-zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile-butadiene rubber. The overall content of the filler, or fillers combinations was kept on 200 phr. Then, carbon black, or carbon fibres, respectively were incorporated into each rubber formulation in constant loading - 25 phr, while the content of magnetic fillers was unchanged - 200 phr. The work was focused on the understanding of correlation among electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding ability of materials was evaluated within the frequency range from 1 MHz to 6 GHz. The study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although, the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites were reached over 6 GHz. The application of carbon based fillers resulted in higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. Though, the composites with filled with ferrites and carbon based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon based fillers caused the improvement in tensile behavior of composites. The study also demonstrated that the higher was the ratio of nickel-zinc ferrite in magnetic fillers combinations, the higher was the absorption shielding performance.

The present study aims at investigating the potential impact of agricultural policies on GHG emissions from agriculture across the European Union. The study begins with a brief analysis of the context of implementation of the 2014-2022 Common Agricultural Policy (CAP), within which many interventions were designed to improve sustainability and increase competitiveness. It follows a description of the structural changes the European agriculture is witnessing, that are both influenced and contribute influencing policies. The method of Qualitative Comparative Analysis (QCA) is used to investigate possible causalities and to cluster observations based on similar combinations of conditions (i.e., drivers) and outcomes (i.e., positive or negative variations in GHG emissions from agriculture between the end and the begin of the CAP programming period). The results reveal that the increase in GHG emissions from agriculture over the study period is mainly attributable to the low share of agricultural land under management contracts targeting climate change mitigation and carbon sequestration through the CAP. CAP payments coupled with the production is found to contribute to further increasing GHG emission from agriculture in some eastern and northern EU countries. Livestock concentration, income support payments and the high price of agricultural land drive the increase in GHG emissions for other central and eastern EU countries. The paper concludes addressing existing shortcomings due to conflicting interventions in the current CAP Strategic Plans.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

This study, conducted with meticulous attention to detail, comprehensively examines the state of plants and their adaptation to Kazakhstan's extra-arid climatic zone of the Mangistau. It uses the collections of woody plants from the Mangyshlak Experimental Botanical Garden in Aktau as a case study and extrapolates the results to the entire region. The study area is arid and unsuitable for many plants, so examining physiological adaptation mechanisms and strategies for preserving plants in unfavourable conditions is crucial. The study employed a range of methods, including the measurement of the intensity of transpiration, leaf hydration, and the content of chlorophyll A, B, and carotenoids. These methods were chosen for their proven effectiveness in similar studies and their ability to provide accurate and reliable data. The samples were also assessed using a point system for resistance to drought, phytophagy, gas tolerance, salt tolerance, winter hardiness, and soil fertility. The results obtained and entered into the IEBG platform “DinTseR” to assess the value of the introduction using a diagnostic scale revealed a high variability (up to 51.7-52.2%) of physiological indicators of growth and development. The highest values of transpiration intensity were observed in deciduous trees and shrubs, rose varieties (205-243 mg/g fresh leaf mass per hour), leaf water content - in climbing plants (68.9%), chlorophyll A and B content - in deciduous plants, and plants - old trees, fruit trees and varietal roses (3.46-3.93 and 1.34-1.84%). Their concentration in coniferous species is almost two times lower (0.63%). A correlation was also made between various significant factors. Twenty regression equations and forecasts have been identified that can be used to diagnose and assess resistance, thereby reducing the cost of determining the introduction value in the conditions of Mangistau. These findings are essential in understanding and preserving the unique flora of the Mangistau region.

This study presents a reproducible and scalable method for synthesizing silica nanoparticles (SNPs) with controlled sizes below 200 nm, achieved by systematically varying three key reaction parameters: ammonium hydroxide concentration, water concentration, and temperature. SNPs with high monodispersity and controlled dimensions were produced by optimizing these factors. The results indicated a direct correlation between ammonium hydroxide concentration and particle size, while higher temperatures resulted in smaller particles with increased polydispersity. Water concentration also influenced particle size, with a quadratic relationship observed. This method provides a robust approach for tailoring SNP sizes, with significant implications for biomedical applications, particularly in drug delivery and diagnostics. Using eco-friendly solvents such as ethanol further enhances the sustainability and cost-effectiveness of the process.

Wide-bandgap tin oxide (SnO₂) thin-films are frequently used as an electron-transporting layers in perovskite solar cells due to superior thermal and environmental stabilities. However, its crystallization by conventional thermal methods requires typical temperatures between 300 and 900 ◦C [1] with up-to 60 min crystallization times. These post-processing conditions severely limit the choice of substrates and reduce the large-scale manufacturing capabilities. This work describes the intense pulsed light-induced crystallization of SnO₂ thin films using only 500 μs of exposure time. Thin-film properties are investigated using both impedance spectroscopy and photoconductivity characteristic measurements. Nyquist plot analysis establishes that the process parameters have a significant impact on the electronic and ionic behaviors of the SnO2 films. Most importantly, we demonstrate that light-induced crystallization yields improved topography and excellent electrical properties through enhanced charge transfer, improved interfacial morphology and better ohmic contacts compared to thermally-annealed SnO₂ films.

The kinetic analysis of octogen coating with a polyurethane base containing hydroxyl-terminated polybutadi-ene (HTPB) was investigated using infrared spectroscopy. The coating process involved a solvent method, where octogen and liquid polyurethane were mixed, the solvent was evaporated, and curing took place at an elevated temperature. The ratio of HTPB to diisocyanate was equimolar. Initially, the curing process occurred in the solvent system, followed by further curing in the bulk system. The kinetic analysis was performed using a modified diffusion-autocatalytic model, which includes non-catalytic, autocatalytic, and diffusion compo-nents. This model was compared with others during the bulk reaction and proved to be effective in correcting errors, particularly in the gel time region. Thermodynamic parameters were evaluated using the Arrhenius and Eyring equations. The reaction rate was initially controlled by chemical reactivity, but after the gel time, diffusion became the controlling factor. In the HTPB-TDI system, both the non-catalytic and autocatalytic parts decreased with increasing temperature, while diffusivity increased. It is worth noting that diffusivity is temperature-dependent. Different diisocyanates, namely toluene diisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HMDI), were studied, revealing that HMDI exhibited higher reactivi-ty than TDI and IPDI. The catalyst effect on reaction rate HTPB-TDI system is investigated. Catalysts adding (0.1%) to HTPB-TDI system is really decrease their activation energy by efectivity DBTL>FeAA>TPB. Catalyst not change their diffusivity.

Continuous casting is the most common method for producing steel into semi-finished shapes like billets or slabs. Throughout this process, steel experiences mechanical and thermal stresses, which influence its mechanical properties. During continuous casting, decreased formability in steel components leads to crack formation and failure. One reason for this phenomenon is the appearance of the soft ferrite phase during cooling. However, it is unclear under which conditions this ferrite is detrimental to the formability. In the present research, we investigated what microstructural changes decrease the formability of microalloyed steels during continuous casting. We studied the hot compression behaviour of microalloyed steel over temperatures ranging from 650 °C to 1100 °C and strain rates of 0.1 s-1 to 0.001 s-1 using a Gleeble 3800® device. We examined microstructural changes at various deformation conditions using microscopy. Furthermore, we implemented a physically-based model to describe the deformation of austenite and ferrite. The model describes the work hardening and dynamic restoration mechanisms, i.e., discontinuous dynamic recrystallisation (dDRX) in austenite and dynamic recovery (DRV) in ferrite and austenite. The model considers the stress, strain, and strain rate distribution between phases by describing the dynamic phase transformation during the deformation in iso-work conditions. Increasing the strain rate below the transformation temperature improves hot ductility by reducing DRV and strain concentration in ferrite. Due to limited grain boundary sliding, the hot ductility improves at lower temperatures (<750 °C). In the single-phase domain, DRX improves the hot ductility provided that fracture occurs at strains in which DRX advances. However, at very low strain rates, the ductility decreases due to prolonged time for grain boundary sliding and crack propagation.

The olive tree (Olea europaea L.) is an evergreen tree that occupies 19% of the woody crop area and is cultivated in 67 countries on five continents. The largest olive production is concentrated in the Mediterranean basin, where the olive tree has had an enormous economic, cultural and environmental impact since the 7th century BC. In the Mediterranean region, salinity stands out as one of the main abiotic stress factors significantly affecting agricultural production. Moreover, climate change is expected to lead to increased salinisation in this region, threatening olive productivity. Salt stress causes combined damage by osmotic stress and ionic toxicity, restricting olive growth and interfering with multiple metabolic processes. A large variability in salinity tolerance among olive cultivars has been described. This paper aims to synthesize information from the published literature on olive adaptations to salt stress and its importance in salinity tolerance. The morphological, physiological, biochemical, and molecular mechanisms of olive tolerance to salt stress are reviewed.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

Vanadium is a well-known essential trace element, which usually exists in oxidation states in form of vanadate cation intracellularly. The pharmacological study of vanadium begins at the discovery of its unexpected inhibitory effect on ATPase. Thereafter, the protective effects on cells and the abilities in glucose metabolism regulation were observed from vanadium compound, leading to the application of vanadium compounds in clinical trials for curing diabetes. Alzheimer’s dis-ease (AD) is the most common dementia disease in elderly people. However, there is still no efficient agents for treating AD safely to date. This is mainly because of the complexity of the pathology, which are characterized by the senile plaques composed by amyloid-beta (Aβ) protein in the parenchyma of brain and the neurofibrillary tangles (NFTs) derived from hyperphosphorylated tau protein in neurocyte, along with mitochondrial damage, and eventually the central nervous system (CNS) atrophy. AD was also illustrated as type-3 diabetes, because of the observations of insulin deficiency and the high level of glucose in cerebrospinal fluid (CSF), as well as the im-paired insulin signaling in brain. In this review, we summarized the advance of applicating vanadium compound on AD treatment in experimental research and pointed out the limitation of the current study on using vanadium compounds in AD treatment. We hope it will help the future study in this field.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

Self-compacting concrete is essential for vertical structures due to high reinforcement and usage of pumps for transporting the concrete at the working site. SCC is mainly influenced by self-curing for arid areas. To explore the SCC (Self-Compacting Concrete) mixture and condition influencing the self-curing condition were determined using the experimental procedure. Determination of various parameters was done using T50 slump flow, V-funnel, L-box-box, J ring test, compressive strength, splitting tensile strength, and flexural strength test. After the experimental investigation, it shows that if the dose if the dosage of superplasticizer (SNF%) increases, it will improve the concrete mixture's different properties, such as flowability and ability to pass. Higher water-to-cement ratios (w/c) generally result in enhanced flowability and stability. Mixture 9 (SNF 0.35, w/c 0.5) demonstrates favourable results across all parameters, indicating excellent flowability and stability. Mixture 9 (SNF 0.35, w/c 0.5) also shows favourable flowability and stability characteristics. Lower concentrations, such as 0.5%, may have a positive effect up to a certain point but might not provide sustained improvement over the curing period. On the other hand, concentrations of 1% and 2% demonstrated consistent and significant enhancement in strength throughout the 28 days. It is found that the higher concentrations of PEG 4000 may be more effective in improving the material strength.

Through the geometric relationships and force analysis of the main components of the panto-graph on high-speed trains, coefficients of aerodynamic forces and lift transmission between the pantograph and main components under crosswind conditions were derived. Based on the aer-odynamic forces acting on the pantograph at different crosswind speeds, wind angles, and oper-ating speeds, the aerodynamic lift of the pantograph and main components was ultimately de-termined. The results indicate that the aerodynamic lift of the pantograph is mainly distributed on the bow structure, with the aerodynamic lift of the upper frame all being negative values, while the absolute value of the aerodynamic lift of the lower arm rod is the smallest. The oper-ating speed of the pantograph and the wind angle of the crosswind have a significant impact on the aerodynamic lift of the main components, while the impact of the crosswind speed is rela-tively small. At the same operating speed of the pantograph, the lower the corresponding crosswind speed, the smaller the aerodynamic lift of the pantograph. The aerodynamic lift of the pantograph tends to decrease gradually with the increase of crosswind speed, and the impact of crosswind speed decreases gradually with the increase of pantograph operating speed. A com-prehensive relationship formula between the aerodynamic lift of the pantograph and the oper-ating speed, crosswind speed, and wind angle is obtained, and the empirical formula for the contact force of the bow net and train operating speed is modified. The research results are of great significance and value for the study and application of lift forces on pantographs under crosswind conditions.

Reactive powder concrete (RPC) is a modern form of cementitious material. Major components include cement with a very low water-to-binder (w/b) ratio, steel fibres, superplasticizers, and very fine additives used in place of coarse aggregate, and very little water. The primary goal of this study is to examine the impact of immersion in sulfuric acid on compressive strength and to evaluate the impact of curing procedures on the preparation of RPC with high characteristics. The experimental work includes 4 mixes, which are prepared using 30 mm hooked-end steel fibers with a ratio of 0.4 by volume, silica fume and metakaolin with a ratio of 25% of cement weight. Compressive and indirect tensile strengths, ultrasonic velocity, and bulk density tests were conducted on the RPC that was prepared to evaluate its qualities. The results showed that heat curing resulted in a greater increase in strength than water curing did, and that mechanical properties improved with increasing SF more than MK additions. Heat-cured RPC demonstrated greater resistance to sulfuric acid immersion tests on compressive strength compared to water-cured RPC.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The optimization of photovoltaic (PV) systems is vital for enhancing efficiency and economic viability, especially under Partial Shading Conditions (PSCs). This study focuses on the development and comparison of traditional and advanced algorithms, including Perturb and Observe (P&O), Incremental Conductance (IC), Fuzzy Logic Control (FLC), Grey Wolf Optimization (GWO), Particle Swarm Optimization (PSO), and Artificial Neural Networks (ANN), for efficient Maximum Power Point Tracking (MPPT). Simulations conducted in MATLAB/SIMULINK evaluated these algorithms’ performance under various shading scenarios. The results indicate that while traditional methods like P&O and IC are effective under uniform conditions, advanced techniques, particularly ANN-based MPPT, exhibit superior efficiency and faster convergence under PSCs. The study concludes that integrating AI and ML into MPPT algorithms significantly enhances the reliability and efficiency of PV systems, paving the way for broader adoption of solar energy technologies in diverse environmental conditions. These findings contribute to advancing renewable energy technology and support the green energy transition.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

The over use of pharmaceutical compounds, essentially antibiotics, led to an increase of their concentrations in aquatic ecosystems. In this study, the white-rot fungus Coriolopsis gallica (high-laccase-producing fungus) was investigated for the biodegradation of ampicillin (AMP) under different cultivation conditions. The biotransformation of the antibiotic was confirmed by means of high-performance liquid chromatography (HPLC), and the antibacterial activity was evaluated via the bacterial growth inhibition agar well diffusion method using Escherichia coli as an ampicillin-sensitive test strain. The results showed that AMP (50 mg L-1) was totally removed by C. gallica after 6 days of incubation in a liquid medium. The antibiotic removal rate was maximal with a fungal culture aged 9 days. Such a culture achieved the removal of a higher concentration of up to 500 mg L-1 of ampicillin in 3 days. This higher antibiotic removal rate was concomitant with the maximal laccase production in culture supernatant. In addition, four consecutive doses of 500 mg L-1 of ampicillin were transformed by the same fungal culture in 24 days. After that, the fungus was unable to remove the antibiotic. The measurement of ligninolytic enzyme activity showed that laccase of C. gallica might participate in the biotransformation of AMP.

We primarily investigate the existence of solutions for fractional neutral integro-differential equations subjected to Neumann-type boundary conditions, which is crucial for understanding natural phenomena. Taking into account factors such as neutral type, fractional-order integrals, and fractional-order derivatives, we employ probability density functions, Laplace transforms, and resolvent operators to formulate a well-defined concept of a mild solution for the specified equation. Following this, by integrating fixed point theorems, we establish the existence of mild solutions under more relaxed conditions.

Mesenchymal stem cells (MSCs) hold immense therapeutic potential due to their regenerative and immunomodulatory properties. However, to utilize this potential, it is crucial to optimize their in vitro cultivation conditions. Three-dimensional (3D) culture methods using cell-laden hydrogels aim to mimic the physiological microenvironment in vitro, thus preserving MSC biological functionalities. Cellulosic hydrogels are particularly promising due to their biocompatibility, sustainability, and tunability in terms of chemical, morphological, and mechanical properties. This study investigated the impact of (1) two physical crosslinking scenarios for hydrogels derived from anionic cellulose nanofibers (CNF) used to encapsulate adipose-derived MSCs (adMSCs) and (2) physiological culture conditions on the in vitro proliferation, differentiation, and extracellular vesicle (EV) production of these adMSCs. Our results revealed that additional Ca2+-mediated crosslinking, intended to complement self-assembly and gelation of aqueous to-CNF in the adMSC cultivation medium, adversely affected both the mechanical properties of the hydrogel spheres and the growth of the encapsulated cells. However, cultivation under dynamic and hypoxic conditions significantly improved the proliferation and differentiation of the encapsulated adMSCs. Furthermore, we demonstrated that adMSCs in CNF hydrogel spheres exhibited potential for scalable EV production with potent immunosuppressive capacities in a bioreactor system. These findings underscore the importance of physiological culture conditions and the suitability of cellulosic materials for enhancing the therapeutic potential of MSCs. Overall, our study provides valuable insights for optimizing the in vitro cultivation of MSCs for various applications, including tissue engineering, drug testing, and EV-based therapies.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

Blockchain technology (BCT) has the potential for sustainable development, enhancing business efficiency, reducing costs, and strengthening data security. Despite its potential, adoption among small and medium-sized enterprises (SMEs) is low due to the need for significant changes in technology infrastructure and the challenge of interoperability. A cross-sectional survey was done with 226 Hong Kong SMEs. The PLS-SEM results highlighted favorable transformation conditions as the most critical factor for SMEs considering the adoption of BCT. These conditions address both internal and external readiness for adopting the disruptive strategy. Other contributing factors to BCT adoption include trust in BCT developers, perceived usefulness and ease of use, government support, and perceived security. The research results contributed to the literature on disruptive technology acceptance, adoption, transformation conditions, technology readiness, and SMEs’ technology adoption. Government-supported policies and initiatives can promote BCT adoption, including educational programs, case studies, and resources for readiness. Financial support and regulatory frameworks can further encourage adoption. BCT developers can demonstrate the value of their systems, effectively communicate potential ROI and cost savings, and provide user-friendly interfaces to increase SMEs’ intention to adopt BCT.

Peroxisome proliferator-activated receptors (PPARs) are important targets for cannabidiol (CBD), which mediate many of its biological actions. The hypothesis of the present research assumed that PPARs affect the gut response to different challenge factors in chickens (C. perfringens vs lipopolysaccharides (LPS) from E. coli), and CBD can mediate the pathways of this response. The study proved that CBD and challenge factors significantly affect the expression level of PPARα (P=0.001) and selected genes determining gut barrier function. A positive correlation was demonstrated between PPARs and genes involved in the formation of tight junctions, immune and oxidative stress responses in chickens. Dietary supplementation with CBD actively mediated the expression rate of PPARs, but the mechanism of interaction between CBD and PPARs was different depending on the stress factor used. The addition of CBD to the birds’ diets did not contribute to reducing intestinal permeability under induced stress conditions and did not cause a stress-inducing effect resulting in the increase of cortisol and endotoxin concentration in the blood. CBD also supported the mechanisms of protecting intestinal cells from cytotoxic effects in a C. perfringens challenge. This study indicates the importance of research towards understanding the mechanisms of PPARs as a target for enhancing intestinal barrier function, provides new results on the biological action of CBD in chickens and shows a constant PPARs association with the jejunum mucosa of birds.

(1) Background: a study was undertaken to determine the prevalence of chronic diseases and health conditions that affect oral health and oral health self-care among independent living older adults in rural areas of Victoria, Australia; (2) Methods: The study analysed data from the Crossroads-II project, with a total of 1407 participants aged 55 years and older. Participants self-completed questionnaires about health conditions, service use, and demographics. 572 attended a 2-hour health screening that included an assessment of prescribed medications; (3) Results: Most participants were female (55.3%), with a mean age of 69.1 (SD=9.2) years. Participants had a high prevalence of medical conditions, the most common were high blood pressure, arthritis, high lipids, hearing loss, and chronic pain. Almost all participants reported taking medications, with an average of 4.3 medications per person. Among those who attended the health screening, 78.1% were taking medications that could cause xerostomia (dry mouth); (4) Conclusions: This study provides initial information on the prevalence of medical conditions, medication usage, with potential impact on oral health of older adults living in rural Victoria. This information would be valuable for healthcare and dental workforce planning, policy development, and improving the overall well-being of this population.

The Circular Bioeconomy (CBE) combines the concepts of bioeconomy and circular economy. As an alternative concept to the current fossil-based, linear economy, it de-scribes an economy based on the efficient valorization of biomass. It is regional in nature and aims to improve sustainability. An analysis of the transition process, by identifying its success criteria and assessing its impacts through the modelling of technology-specific scenarios is necessary to ensure that CBE concepts are sustainable. However, a compre-hensive consideration of regional influences on both is lacking. Based on extensive literature research and an expert survey, we (i) present a compre-hensive catalog of CBE success criteria and discuss their region-specific character and (ii) develop a methodology based on evaluation matrices that enable to match CBE technolo-gies with regions. The matrices support the evaluation of technological and regional characteristics influencing the successful CBE implementation. The results show that the success criteria "biomass resources", "technological", and "social" are perceived as highly important, and that most of the success criteria are both region- and technology-specific, highlighting the relevance of developing matrices to match them. We describe such matrices indicatively for the two broadest and most im-portant success criteria clusters “social acceptance” and “biomass supply chain”. With this, we substantiate the regional nature of CBE and raise the awareness on the importance of considering regional conditions in CBE transition processes. Furthermore, we provide practical guidance on how regional conditions can be reflected in the selection of technologies, e.g. in regional CBE technology scenarios.

Conditions under which compositions of component systems form a well-defined system-of-systems here are formulated at a fundamental level. Statement of what defines a well-defined composition and sufficient conditions guaranteeing such a result offers insight into exemplars that can be found in special cases such as differential equation and discrete event systems. For any given global state of a composition, two requirements can be stated informally as: 1) the system can leave this state, i.e., there is at least one trajectory defined that starts from the state, and 2) the trajectory evolves over time without getting stuck at a point in time. Considered for every global state, these conditions determine whether the resultant is a well-defined system and if so, whether it is non-deterministic or deterministic. We formulate these questions within the framework of iterative specifications for mathematical system models that are shown to be behaviorally equivalent to the Discrete Event System Specification (DEVS) formalism. This formalization supports definitions and proofs of the afore-mentioned conditions. Implications are drawn at the fundamental level of existence where the emergence of a system from an assemblage of components can be characterized. We focus on systems with feedback coupling where existence and uniqueness of solutions is problematic.

In order to effectively utilize red mud and reduce its occupation of land resources as well as its impact on the environment, experiments were conducted to develop stabilized soil materials using nano-SiO2 synergistically modified red mud and to investigate the curing mechanism of stabilized soil. The unconfined compressive strength, microscopic morphology and curing mechanism of the red mud-based stabilized soil materials with different amounts of modified materials were investigated. The test results show that after 7-days curing, the unconfined compressive strength of red mud-based stabilized soil meets the compressive strength requirement of road base material when nano-SiO2, gypsum and cement are synergistically modified. In such case, the soil structure has the lowest fracture rate and the best structural compactness when the amount of nano-SiO2 is 1%; It is found that the needle-like and columnar calcium alumina in the modified red mud-based stabilized soil increases, and the binding energy of hydration product ions in the modified material is improved; The chemical curing mechanism of modified red mud-based stabilized soil includes hydration reaction, volcanic ash reaction, promotion effect of nano-SiO2, and enhancement effect of gypsum. On this base, a model of early start hydration process of red mud-based stabilized soil promoted by nano-SiO2 is established.

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p < 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p < 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

A protocol was designed for plasmid curing using a novel counter-selectable marker, named pylSZK-pylT, in Escherichia coli. The pylSZK-pylT marker consists of the archaeal pyrrolysyl-tRNA synthetase (PylRS) and its cognate tRNA (tRNApyl) with modification, and incorporates an unnatural amino acid (Uaa), Nε-benzyloxycarbonyl-l-lysine (ZK), at a sense codon in ribosomally synthesized proteins, resulting in bacterial growth inhibition or killing. Plasmid curing is performed by exerting toxicity on pylSZK-pylT located on the target plasmid, and selecting only proliferative bacteria. All tested bacteria obtained using this protocol had lost the target plasmid (64/64), suggesting that plasmid curing was successful. Next, we attempted to exchange plasmids with the identical replication origin and an antibiotic resistance gene without plasmid curing using a modified protocol, assuming substitution of plasmids complementing genomic essential genes. All randomly selected bacteria after screening had only the substitute plasmid and no target plasmid (25/25), suggesting that plasmid exchange was also accomplished. Counter-selectable markers based on PylRS-tRNApyl, such as pylSZK-pylT, may be scalable in application due to their independence from the host genotype, applicability to a wide range of species, and high tunability due to the freedom of choice of target codons and Uaa’s to be incorporated.

Autoimmune Glomerulonephritis represents a homogeneous area of renal pathology with clinical relevance for either the numerical impact or difficulties in treatment. SLE and Lupus nephritis are the most frequent occurrences. They are characterized by glomerular deposition of circulating autoantibodies that recognize glomerular antigens Technologies for studying tissue and circulating antibodies have evolved over the years and culminated with the direct analysis of the antigen-antibody complex in renal bioptic fragments. Mass-spectrometry of immunoprecipitates from the renal tissue is, in fact, the most recent evolution that eliminates the need for tissue microdissection. The results obtained with this technique have led to the discovery of several new glomerular antigens in Membranous Nephropathy and in Lupus Nephritis, two conditions whose pathogenesis remained unknown for decades, Peptide and protein arrays (Immunopeptidomics and immunoproteomics, respectively) for the characterization of circulating autoantibodies represent the new frontier for identifying autoantibodies. Immunopeptidomics consists in 7.5 million aligned peptides of 16 amino acids each which cover the whole human proteome; immunoproteomics utilizes a chip containing structured proteins, 26.000 overall. Both are very sensitive techniques that allow the characterization of hundreds of new antibodies in circulation. The contribution of arrays to amplify the panel of potential autoantibodies involved in glomerulonephritis is expected to be relevant for improving our knowledge of the pathogenesis of several autoimmune conditions.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID-19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing the amount of relatively expensive UV resin, and iv) enabling production of handle on more accessible material extrusion 3-D printers. A modular open source UV LED box was designed, fabricated for $45 and tested for batch curing. Swabs can be fabricated for $0.06-$0.12/swab. The results of the mechanical validation tests showed that the swabs could withstand greater forces than would be expected in normal clinical use. The swabs were also able to absorb a significant amounts of synthetic mucus materials and passed abrasion and handling tests. The results show the open source swab are promising candidates for clinical trials.

Sustainability is a characteristic manifested in the ability to maintain the necessary level of performance for construction companies when risk factors arise during the implementation of investment and construction projects. The risk factors that arise during the implementation of in-vestment and construction projects differ in nature, degree of influence, and other characteristics. Ignoring these factors and measures to manage them often leads to critical consequences in the form of disruptions in the timing of work. Risk is a combination of the probability and consequences of the occurrence of adverse events. The article considers the concept of risk as a potential possibility of occurrence of adverse situations and related consequences when exposed to these factors. Risk factors are characterized by surprise, discreteness of changes, the presence of threshold values, upon reaching which a transition to a different mode of operation is required. The article discusses the risk factors arising at the construction stage, their classification. A methodology has been developed that includes conducting a survey in the form of a questionnaire in order to collect information about risk factors that affect the implementation of investment and construction projects. Experts with experience in the construction sector were involved in the survey. The processing of the survey results made it possible to assess the significance of various risk factors in investment and construction projects. Thus, statistical and expert methods were used in the study. The results showed that financial, technical, legal, economic, managerial and natural factors have the greatest impact on investment and construction projects. It is recommended to pay special attention to the listed factors when developing measures aimed at preventing risks and their consequences. The methodology described in the study can be used by construction companies in strategic planning. The analysis of the stability of construction companies, depending on their use of various ways to counteract risk factors, allowed us to develop a number of practical recommendations to reduce the impact of the studied factors on achieving the goals of investment and construction projects.

The nutrient absorption and utilization efficiency in the roots of seedlings are beneficial for increasing crop yield. Creating marker assisted selection for wheat root traits can assist wheat breeders in choosing robust roots to maximize nutrient uptake. Exploring and identifying the effect of different nitrogen applications on RSA is of great significance for breeding nitrogen efficient wheat varieties. In this study, A total of 243 wheat varieties native to the Yellow and Huai Valley regions of China were utilized for genome-wide association studies (GWAS). Furthermore, a recombinant inbred line (RIL) population of 123 lines derived from the cross between Avocet and Chilero was utilized for linkage examination and confirmation of the hereditary loci distinguished by GWAS. Five RSA traits include the relative number of root tips (RNRT); relative total root length (RTRL); relative total root surface area (RTRS); relative total root volume (RTRV) and relative average root diameter (RARD) where evaluated under two N conditions—normal N (NN) supply and low N (LN)—to characterize the NUE of each accession. GWAS and linkage analysis were performed by integrating data from the wheat 660k single nucleotide polymorphism (SNP) chip and diversity arrays technology (DArT) to identify genetic loci associated with RSA. The results showed that based on the ratio of RSA related traits under two N supply conditions, a total of 598 SNP markers, which are significantly associated with RSA related traits, were detected at 160 genetic loci by GWAS. A total of 10 QTL loci related to RSA were dis-covered and identified by linkage mapping. In which, three significant RSA related Quantitative Trait Locus (QTL) were identified, namely qRtrl-3D, qRnrt-3D, and qRtrl-7D. The study has the potential to enhance the effectiveness of selecting root traits in wheat breeding programs, offering valuable insights into the genetic underpinnings of nitro-gen use efficiency (NUE) in wheat. This could lead to the creation of NUE wheat varieties by implementing focused breeding strategies.

In arid and semi-arid regions like Tunisia, irrigation water is typically saline, posing a soil and crop salinization risk and yield reduction. This research aims to study the combined effects of soil matric and osmotic potential stresses on tomato root water uptake. Plants were grown in pot and field experiments in loamy-clay soils and were irrigated with three different irrigation water qualities: 0, 3.5, and 7 dS/m. The Hydrus-1D model was used to simulate the combined dynamics of subsurface soil water and salts. Successful calibration and validation of the model against measured water and salt profiles enabled the examination of the combined effects of osmotic and matric potential stresses on root water uptake. Relative yields, indirectly estimated from actual and potential transpiration, indicated that the multiplicative stress response model effectively simulated measured yields and the impact of saline water irrigation on crop yields. The gradual salinization of the root zone further evidenced this effect. The scenario considering a temperature increase of 2°C had no significant impact on crop yields in the pot and field experiments.

Monitoring the integrity of aeronautical structures is fundamental for safety. Structural Health Monitoring Systems (SHMS) perform real-time monitoring functions, but their performances must be carefully assessed. In this work the damage detection performances of a strain-based SHMS, were evaluated on a composite helicopter rotor blade root. The SHMS monitored the bonding between the central core and the surrounding antitorsional layer. A damage detection algorithm was trained through Finite Element analyses performed on the component. The effects of the loads variability and of damages were decoupled by including a load recognition step in the algorithm. Load recognition was accomplished in different ways: version#1 adopted an Artificial Neural Network (ANN) trained on blades in pristine condition; version#2 was trained also on damaged blades; version#3 adopted a calibration matrix method. Anomaly detection, damage assessment, and localization were performed by using an ANN. Results showed a higher load identification and anomaly detection accuracy for version#1 and version#2 compared to version#3. Gaussian noise reduced anomaly detection and damage assessment performances, and reduced damage localization accuracy for bigger damages. The damage detection performance were obtained for a fibre optic based-SHMS, including the trade-off between probability of detection and false alarm rate for different damage sizes.

During meat processing, lactic acid bacteria (LAB) have to competitively adapt to the hostile en-vironment produced by curing additives (CA). The objective of this study was to investigate the ability of Latilactobacillus curvatus CRL 705, a bioprotective strain of meat origin, to adapt to CA. A physiological and proteomic approach was performed. CRL 705 was grown in a chemically de-fined medium (CDM) containing specific concentrations of CA (NaCl, nitrite, sucrose and ascor-bic acid). The results showed minor differences in growth kinetics in the presence of CA. Glucose consumption, present in CDM, and production of lactic acid and bacteriocins were not signifi-cantly affected. Proteomic analyses indicated that most of the identified proteins (36 out of 39) mainly related to carbohydrate metabolism (18%), posttranslational modifications (15.6%), energy production and conversion (11.1%), translation (11.1%) and nucleotide metabolism (8.9%), were under expressed. In response to the studied CA, CRL 705 slowed down its general metabolism, achieving slight changes in physiological and proteomic parameters. The observed performance is another characteristic that extends the well-known competitive profile of CRL 705 as a meat starter- and -bioprotective culture. This is the first report dealing with the impact of CA on LAB proteomics.

Nowadays, the identification and characterization of grapevine cultivars resilient to climate and water stress while preserving quality traits is crucial for the wine industry. Therefore, the objective of this work was to characterize according to their aromatic potential 9 white and 6 red minority cultivars recently recovered from Castilla-La Mancha region (Spain), subjected at two different water deficit regimes: rainfed, with subsistence irrigation, and irrigated. For this, the varietal aromatic potential index (IPAv) and the detailed aromatic composition were analyzed by HS-SBSE-GC/MS, in extracts of two different ph. For IPAv values, red varieties did not show a clear trend with respect to irrigation. However, in white minority varieties, higher values were obtained under irrigation conditions. Thus, a clear differentiation of the minority varieties in comparison to the references was observed, primarily attributed to the content of esters and acids, in both white and red varieties. A notable contrast was observed at different pH, indicating a greater extractability of certain compounds like linalool, under more acidic conditions. This suggests that some recovered minority cultivars could be promising for cultivation in semi-arid regions with limited water, contributing to the wine sector sustainability in the future.

Abstract: The Tropical Rainfall Measuring Mission (TRMM) and then Global Precipitation Mission (GPM) are the most important and widely used data sources in the forecasting of drought, flood, and water resources management. However, since this sensor’s data is primarily used for tropical regions, it is necessary to evaluate the accuracy for optimal use of the data across varying climatic and physiographic conditions. In this study, the accuracy of the satellite data for a span of 17 years (2000-2017) for three climatic zones has been explored using synoptic ground station data. The climates include a) arid and low rainfall, b) semi-arid and low rainfall, and c) humid and high rainfall. We evaluated satellite data accuracy in drought and wet conditions based on the Standard Precipitation Index (S.P.I.) and different seasons. For available ground control stations, 13 stations were used in the humid, seven stations in a semi-arid climate, and 12 stations in the dry climate. The results show that the monthly precipitation product of GPM (IMERG product) and TRMM (TMPA/3B43 product) overestimate the rainfall. In the arid climate, the precipitation is estimated 43%, in the semi-arid environment 50%, and in the humid weather 11% more than the ground-based data on average. Therefore, to use satellite data in different climates, it is necessary to make corrections to obtain precise results. Based on 32 ground stations, the correction coefficient has a positive relationship with average precipitation and altitude and an inverse relationship with the latitude. Further in-depth investigations showed that the accuracy of satellite data in wet conditions is higher than the accuracy of normal circumstances, and the accuracy of normal conditions is more accurate than drought conditions. Besides, the accuracy of satellite data in wet or dry conditions increases with increasing time scales. The highest accuracy was obtained for a 12-month time scale and the lowest accuracy for the 3-month time scale of drought conditions in the arid climate.

Pseudomonas donghuensis P482 exhibits broad antibacterial and antifungal activity, primarily related to the production of 7-hydroxytropolone (7-HT). However, the restricted nutritional conditions (viz. mineral medium with single carbon source) diminished the antagonistic activity of P482. In this study, we unveil profiles of the secondary metabolites from P482 and its selected mutants, using nutrient-diluted (10% tryptone soy broth, TSB) and nutrient-restricted (M9 with either 0.4% glucose or 0.4% glycerol as a sole carbon source) media to explore differences in the quantity and quality of the secondary metabolites produced. No 7-HT was found to be synthetized by P482 under restricted nutritional conditions. However, both the wild-type and the tested mutants of P482 still did express some antagonistic activity towards the plant pathogenic bacteria tested. Based on these results, we postulate that 7-HT is not the sole antimicrobial compound produced by P. donghuensis P482 and that other antimicrobials may be involved in P482 antagonistic activity under limiting-nutrient conditions.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

Background/objectives: The health benefits of resistant starch are well known, but there have not been many studies available documenting the effect of basmati rice products containg resistant starch upon blood glucose level and lipid profile in vivo efficacy. Methods: Common cooking methods were used to prepare basmati rice products including two boiling methods viz. boiling 1 (boiling by absorption), boiling 2 (boiling in extra amount of water), frying and pressure cooking. The cooked rice were held at various temperatures and times: it was made fresh (T1), kept at room temperature (20–22°C) for 24 h (T2), kept at 4°C for 24 h (T3), and then reheated after being kept at 4°C for 24 h(T4). Next, the products' proximate composition, total dietary fibre (soluble and insoluble), resistant starch (RS), and In vitro starch digestion rate (rapidly and slowly digested starch) were examined. The effect of RS on blood glucose and lipid profile were measured in humans and rats. Histopathological study of liver and pancreas in rats were also observed. Results: The basmati rice prepared by boiling 1 and stored with T3 was found more effective to control blood glucose and lipid profile. Similarly in rats, the blood glucose level, cholesterol, triglycerides and LDL were reduced about 29.7, 37.9, 31.3 and 30.5% respectively, after consumption of basmsti rice prepared by boiling 1 and stored at T3. Conclusion: Rice products stored at 4⁰C have a high amount of resistant starh, insoluble dietary fibre, slowly digestible starch and low glycemic index. Thus helps to inhibit glycogen and lipid synthesis.

Novolac phenol-formaldehyde resins have gained extensive commercial utilization across diverse applications due to their exceptional mechanical, thermal, and chemical resistance properties. In this investigation, we successfully synthesized a traditional novolac, and a biobased novolac phenol-formaldehyde resin by partially substituting phenol with a bio-oil obtained from the organic phase resulting from the fast pyrolysis of pinewood biomass. Despite extensive investigations into the curing behavior of novolac resins crosslinked with hexamethylenetetramine (HMTA) through numerous model-fitting cure kinetic studies, a comprehensive model for predicting the crosslinking of bio-based phenol-formaldehyde resins in the presence of HMTA has not yet been studied. The primary objective of this research was to compare and apply several commonly used kinetic models to predict the degree of curing and cure rate of the synthesized resins, using DSC dynamic measurements. Our results demonstrated that the autocatalytic model exhibited excellent fitting for the traditional novolac resin and HMTA mixture, while the Kamal model showed better fitting with the experimental data obtained for the bio-based phenol-formaldehyde resin and HMTA system. In addition, the results evidenced a significant drop in the curing temperature by partially replacing phenol with bio-oil. Additionally, the results revealed a notable reduction in curing temperature when phenol was partially substituted with bio-oil. This substitution not only offers environmental benefits but also promotes energy efficiency and enhances production safety. The data collected in this study is pivotal for our subsequent research endeavors, which aim to develop environmentally sustainable materials optimized for use in 3D printing manufacturing processes.

With an ever broadening use of composite materials manufacturers are in high demand of efficient curing cycles to reduce costs and speed up production cycles. One method to to archive this goal is active cure monitoring to determine the exact time of curing needed. This article provides a novel method to measure the cure inside of closed tools by using ultrasonic spectroscopy. For this a simple experiment is used to show the change of the ultrasonic spectrum during the cure of an epoxy. The results clearly show a direct correlation of amplitude and state of cure where the amplitude reaches a global minimum at the glass point.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

Behavior analysis is a widely used non-invasive tool in the practical production routine, as the animal acts as a biosensor capable of reflecting its degree of adaptation and discomfort to some environmental challenge. Predominantly, conventional statistics use occurrence data for behavioral evaluation and well-being estimation, disregarding the temporal sequence of events. The Generalized Sequential Pattern (GSP) algorithm is a data mining method that identifies recurrent sequences that exceed a user-specified support threshold, whose potential has not yet been investigated for broiler chickens in enriched environments. Enrichment aims to increase environmental complexity with promising effects on animal welfare, stimulating priority behaviors and potentially reducing the deleterious effects of heat stress. The objective was to validate the application of the GSP algorithm to identify temporal correlations between heat stress and the behavior of broiler chickens in enriched environments through proof of concept. Video image collection was carried out automatically for 48 continuous hours, analyzing a continuous period of seven hours, from 12:00 PM to 6:00 PM, during two consecutive days of tests for chickens housed in enriched and non-enriched environments under comfort and stress temperatures. Chickens at comfort temperature showed high motivation to perform the behaviors of Preening (P), Foraging (F), Lying down (Ld), Eating (E), and Walking (W) whose sequences <{Ld,P}>; <{Ld,F}>; <{P,F,P}>; <{Ld,P,F}> and <{E,W,F}> were the only ones observed in both treatments. All other sequential patterns (comfort and stress) were distinct, suggesting that environmental enrichment alters the behavioral pattern of broiler chickens. Heat stress drastically reduced the sequential patterns found at the 20% threshold level in the tested environments. The behavior of lying laterally "Ll" is a strong indicator of heat stress in broilers and was only frequent in the non-enriched environment, which may suggest that environmental enrichment provides the animal with better opportunities to adapt to stress-inducing challenges, such as heat.

Extracellular vesicles (EVs) carry diverse cargo of DNA, RNA, proteins, and lipids. They are crucial mediators for regulating various functions through interactions with the host. Recent investigations suggest that EVs or their constituent proteins derived from probiotics could improve the effectiveness of probiotic strains in disease management compared to probiotic strains themselves. This enhanced effec-tiveness arises from their innate antimicrobial properties, which can specifically target pathogenic mol-ecules or cells, in addition to their significant ability to regulate immune responses. Significantly, previous studies have highlighted the inhibitory potential of Lactobacillus crispatus PMC201 against Mycobacterium tuberculosis. In this study, we focused on optimizing isolation conditions for studying extracellular vesicles and proteins from anti-TB potent strains. We provide analysis results based on food-grade media (FGM) optimization and isolation methods. Nanoparticle tracking analysis (NTA) was used to determine se-cretion patterns. Proteomic analysis was performed by liquid chromatography and tandem mass spec-trometry (LC-MS/MS). A total of 64 proteins were identified in the L. crispatus PMC201 strain, particularly enriched in s-layer and splX. Questions remain about their relevance to anti-TB. This anti-tuber strain has potential as a therapeutic agent, given its significant role in intercellular killing. Further studies are needed to investigate its mechanisms of action.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

Salinity, one of the most important abiotic stress factors, affects plant growth and limits agricultural productivity. In the study, the effects of iron (FeNP; 0.025 and 0.05 mM), silver (AgNP; 0,2 ve 0,4 mg L-1) and silicon dioxide (SiNP;7,5 ve 15 mg L-1) nanoparticles on morphological and physiological parameters of in vitro blackberry plants grown under salinity stress (NaCl; 15 mM ve 35 mM) were investigated. According to our study results, it was determined that higher values obtained from SiNP application in terms of shoot development parameters, FeNP application found more succesfull for root development, AgNP application was effective in SPAD, leaf relative water content (LRWC) and relative growth rate (RGR), and FeNP application was increased superoxide dismutase (SOD) and catalase (CAT) enzyme activities. Salt stress was significantly affected the root development, SPAD value, LRWC and RGR, SOD and CAT enzyme activities. As a result, under salt stress conditions, SiNP, FeNP and AgNP applications can significantly reduce the negative effects of stress and promote vegetative development of the plant compared to control conditions.

Weather-related risks in aviation are one of the main causes of accidents worldwide. This article aims to analyze aviation risks resulting from adverse weather conditions, using the case study of the Pucallpa accident that occurred on August 23, 2005, in eastern Peru. In this analysis, we have determined the relationship between meteorological information and aviation risks, presented a matrix of risks associated with the most predominant meteorological variables at Pucallpa airport, and drawn up three maps of meteorological risks indicating the month of the year in which their incidence is most relevant. Finally, we conclude that it is essential to emphasize the importance of considering the prevailing weather conditions at Pucallpa airport to help mitigate the potential risks that may occur during different phases of the flight.

Let $S=\left(s_1, \ldots, s_n\right)$ be a finite sequence of integers. Then $S$ is a Gilbreath sequence of length $n$, $S\in\mathbb{G}_n$, iff $s_1$ is even or odd and $s_2, \ldots, s_n$ are respectively odd or even and $\min\mathbb{K}_{\left(s_1, \ldots, s_m\right)}\leq s_{m+1}\leq\max\mathbb{K}_{\left(s_1, \ldots, s_m\right)}\forall m\in\left[\left.1, n\right)\right.$. This, applied to the order sequence of prime number $P$, defines Gilbreath polynomials and two integer sequences A347924 \cite{oeisA347924} and A347925 \cite{oeisA347925} which are used to prove that Gilbreath conjecture $GC$ is implied by $p_n-2^{n-1}\leqslant\mathcal{P}_{n-1}\left(1\right)$ where $\mathcal{P}_{n-1}\left(1\right)$ is the $n-1$-th Gilbreath polynomial at 1.

To enhance the peak-shaving capability of the boiler, a mathematical model of hydrodynamic and wall temperature characteristics for the water-cooled wall of a 1000 MW boiler was established. The attributes pertaining to the mass flow distribution, the temperature of the effluent working fluid, pressure drop, and the thermal distribution across the wall surfaces at 30% of the boiler's maximum continuous rating (BMCR) were meticulously computed and subjected to a thorough analytical review. The findings suggest that, under the operation at 30% BMCR load, there is a substantial equilibrium in the flow distribution across the quartet of walls that constitute the water-cooled wall assembly. The maximum mass flow rate deviations in the helical and vertical sections are 1.95% and 3.47%, respectively, showing small flow deviations and reasonable distribution. The temperature deviation in the helical section is 0.3 °C, reflecting the characteristic low thermal deviation in helical tubes. While the temperature deviation at the outlet of the vertical section is higher, it remains within safe limits. The pressure loss across the water-cooled wall system amounts to 0.4 MPa. The peak wall temperature reaches 337.5°C, remaining within the material's permissible safety limits. In-depth performance analysis ensures the safe operating conditions of the water-cooled wall during low load conditions.

Based on the nonlinear failure criterion and modified tangential technique, the upper bound solutions of supporting pressure on the deep tunnel face were obtained under pore water pressure conditions. The influence of parameters on the supporting pressure and collapse range was investigated according to the unlimited block failure mechanism. It is found that the upper bound solutions of supporting pressure increase with the growth of the nonlinear coefficient and pore water pressure coefficient. The collapse range of the tunnel face scales out with the increase of the nonlinear coefficient and shrinks when increasing the pore water pressure coefficient. Moreover, with the increase of the nonlinear coefficient, the impact strength on supporting pressure and collapse range declines gradually. According to the calculating results, it is manifest that both the pore water pressure and nonlinear criterion factors have negative impacts on the stability of the tunnel face. Thus, more attention should be paid to these parameters to ensure face stability in deep tunnel construction.

Nicotiana benthamiana plants infected with a potato virus Y isolate (PVYO) under ambient conditions of 25 °C and ~405 parts-per-million (ppm) ambient CO2 display symptoms of chlorosis, leaf curling, and stunting. However, under elevated temperature and CO2 levels (30 °C, 970 ppm), systemic viral titers decrease several-fold, and plants appear asymptomatic. Under the latter conditions we have studied how infection, drought, or both combined affect infection, drought-driven loss of leaf turgor, plant water content, stomatal conductance, metabolome, and hormone (ABA, SA, and JA) levels. We found that drought did not affect viral titers. As expected, drought decreased plant water content and stomatal conductance. Under drought conditions, infection did not alter significantly final water content or loss of leaf turgor progression, but it increased the levels of some sugars and other osmo-protectants. Infection and drought altered the levels of many components of the metabolome. Some components altered by infection were not altered by drought, but most of those altered by drought were also altered by infection. Drought increased the levels of ABA, infection increased the levels of ABA, SA, and JA, and altered their relative balance. The effects of drought and of infection on hormone levels were cumulative when combined. Thus, under ambient conditions that turn a severe infection into an asymptomatic one both, plant physiology parameters and the interplay with drought are affected.

This survey is part of a Hungarian Research OTKA project that examines the vegetation of sandy grasslands along the Danube. During this study, two grass species, Festuca wagneri and Festuca tomanii, were identified as potentially suitable for urban planting and turf establishment based on preliminary research. Our aim was to determine the germination success of seeds from aesthetically selected individuals and to identify the soil types on which they germinate most effectively. This information could be crucial for future cultivation efforts. From the collected Festuca individuals, were analyzed 30 specimens of each taxon under garden conditions and selected the indi-viduals for germination. The Festuca tomanii individuals were uniform, so we selected only 5 individuals. The Festuca wagneri individuals were categorized into three groups: upright, spreading, and low types. It was assumed that Festuca species seeds would germinate better in sandy soils. To test this, seeds from ten Festuca wagneri and five Festuca tomanii individuals, selected based on aesthetic criteria, were sown in six different substrates: a sand-peat mixture, sand, coconut fiber, peat, a coconut fiber-sand mixture, and native sandy soil. Contrary to expectations, the growth and germination rates of seeds sown in peat and coconut fiber substrates were higher than those in native sandy soil. These results suggest that Festuca seeds germinate better on substrates resembling dead plant debris with a peat-like structure or on the surface of live mosses, rather than on bare sand. Among the examined individuals, the seeds from the spreading Festuca wagneri group exhibited the highest germination rate, making this group particularly suitable for urban environments. Addi-tionally, one of the upright Festuca wagneri individuals showed the highest growth rate and should also be considered for urban planting. In contrast, despite their uniform appearance, the Festuca tomanii individuals did not demonstrate similar germination trends. In fact, the seeds from two clumps did not germinate at all, indicating that further selection is necessary.

Fragile X syndrome (FXS) is a genetic disorder caused by a mutation in the fragile X messenger ribonucleoprotein 1 (FMR1) gene and known to be a leading cause of inherited intellectual disability globally. It results in a range of intellectual, developmental, and behavioral problems. Fragile X premutation associated conditions (FXPAC), also caused by a smaller CGG expansion (55 to 200 CGG repeats) in the FMR1 gene, is linked to other conditions that increase morbidity and mortality for affected persons. Limited research has been conducted on the burden, characteristics, diagnosis, and management of these conditions in Africa. This comprehensive review provides an overview of the current literature on FXS and FXPAC in Africa, epidemiology, clinical features and challenges faced, such as discrimination against affected persons, limited awareness and research, poor access to resources and genetic services and treatment. It further provides an in-depth analysis of the existing worldwide data for the diagnosis and treatment of these disorders. This review will improve understanding of FXS and FXPAC in Africa by incorporating existing knowledge, identifying research gaps, and potential topics for future research to enhance the well-being of individuals and families affected by FXS and FXPAC in the region.

Rivers across the globe experience and respond to changes within the riparian corridor. Disturbance of the riparian corridor can affect warmwater, intermediate, and coldwater streams, which can negatively influence instream physical structure and biological communities. This study focused on assessing the influence of riparian habitat on instream structure within the Whitewater River, a coldwater stream system within an agricultural watershed in southeastern Minnesota, USA. Twenty variables (riparian, n = 9; instream, n = 11) were measured at 57 sites across three forks of the Whitewater. Canonical correlation detected significant associations between riparian and instream variables across the river forks, and indicated that wider riparian buffers, more bank grass and shrubs, longer overhanging vegetation, limited bare soil and more rocks on banks were significantly associated with increased instream cover, high levels of coarse substrates with reduced embeddedness, increased pool habitats, and reduced fine sediments. In contrast, excessive fine sediments, lack of riffle habitat, reduced coarse substrates, and high width to depth ratios indicative of impaired instream habitat were associated with narrow riparian buffers and high percentages of bare soil on banks. Riparian corridors have the capacity to enhance and protect physical instream habitat and overall ecosystem health when managed properly. Wide, grassy riparian corridors with stable banks, overhanging vegetation, and limited shade from trees should protect and/or enhance instream physical habitat, providing the structural diversity favored by aquatic communities.

Plant transcriptomes are an extremely dynamic entities shaped spatially and temporally by many intracellular and environmental cues. In this review, we first summarize the complexity and diversity of plant genomes and transcriptomes as a start point for the multitude of transcriptomic responses. Numerous alterations within various tissue and organ-specific transcriptomes as well as the most relevant transcriptomic responses associated with plant acclimation to selected abiotic and biotic stress conditions, from the current studies employing high-throughput transcriptomic analysis are widely discussed. Understanding changes within plant transcriptomes, revealed by in silico functional analysis, allows for the characterization of stress-affected genes and stress acclimatory mechanisms, as well as allows to perform plant metabolic engineering. The latter allow cultivars to produce more secondary metabolites in the future, which are often desirable substances in the biomedical industry. Accordingly, in this review special attention was also paid to characterize the potential of transcriptomic analyses of medicinal species, particularly to search for new cultivars. Extensive characterization of transcriptomic responses in stress would also result in the development of new cultivars that display physiological and molecular mechanisms that allow them to cope with adverse environmental conditions more adequately.

: AlF3 has interesting electrophysical properties, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

: AlF3 has interesting electrophysical parameters, due to which the material is promising for applications in supercapacitors, UV coatings with low refractive index, excimer laser mirrors, and photolithography. The formation of AlF3-based nano- and micro-wires can bring new functionalities to AlF3 material. AlF3 nanowires be used, for example, in functionally modified microprobes for scanning probe microscopy. In this work, we investigate the AlF3 samples obtained by the reaction of initial aluminum with aqueous hydrofluoric acid solution of different concentrations. All the samples were obtained under normal conditions. The morphology of the nanowire samples is studied by scanning electron microscopy. Quantitative energy-dispersive x-ray spectroscopy (EDS) spectra are obtained and analyzed with respect to the feedstock and each other.

Fixed-time artificial insemination is an important technique in swine production that can improve reproductive efficiency and meat production quality by making better use of the genetic potential of breeding males and reducing the costs associated with double or multiple inseminations. Our goal was to evaluate the vaginal application of the GnRH agonist triptorelin acetate to synchronize post-weaning sows and facilitate implantation of a single fixed-time insemination. In a first experiment, the efficacy of treatment with the triptorelin in animals with or without signs of estrus was analyzed using a single insemination at a fixed time compared to the control following the standard insemination strategy. Farrowing rate was comparable between triptorelin and control groups (100 vs. 87.50%), but triptorelin without estrus had a lower rate (50%). Litter size did not differ between groups. Estradiol and progesterone levels at 96- and 120-hours post-weaning were similar in the control and triptorelin groups (P>0.05). These results suggest that Triptorelin has the potential to synchronize ovulation in pigs without affecting post-weaning hormonal profiles. In a second experiment, the objective was to evaluate the productive and economic impact of implementing a treatment with triptorelin acetate 96 hours after weaning compared to the standard insemination protocol. Sows were grouped according to treatment (control vs. triptorelin) and estrus onset (≤5 days and >5 days after weaning considered as late estrus). Farrowing rate was lower in the control late estrus group than in the control and triptorelin groups and similar to the triptorelin late estrus group. No differences were found for litter size, live or dead piglets born (P>0.05). We developed an estimation model to assess the cost/benefit of intravaginal triptorelin administration at 96 h post-weaning. The overall result is that the use of triptorelin increases the benefit per inseminated sow in the range of €15-20. This improvement is mainly related to an increase in the reproductive performance of the treated sows compared to the control sows and the reduction in the number of inseminations per sow. These results highlight the potential of triptorelin to optimize reproductive management in pigs, improving efficiency and economic viability.

It is generally accepted that atherosclerosis is a chronic inflammatory disease. The link between atherosclerosis and other inflammatory diseases such as psoriasis, type 2 diabetes mellitus (T2DM), and rheumatoid arthritis (RA) via metabolic, inflammatory, and immunoregulatory pathways is well established. The aim of our review was to summarize the associations between selected microRNAs (miRs) and long non-coding RNAs (lncRNAs) and atherosclerosis, psoriasis, T2DM, and RA. MicroRNAs are short noncoding RNA molecules involved in cell signaling, intracellular communication, and gene expression. We reviewed the role of miR-146a, miR-210, miR-143, miR-223, miR-126, miR-21, miR-155, miR-145, miR-200, miR-133, miR-135, miR-221, miR-424, and let-7 in atherosclerosis, psoriasis, T2DM, and RA. LncRNAs are RNA transcripts longer than 200 nucleotides that are involved in cellular processes such as apoptosis, metabolism, inflammation, cell differentiation, and proliferation. We evaluated the role of lncRNA-H19, lncRNA-MEG3, lncRNA-UCA1, and lncRNA-XIST in atherosclerosis and psoriasis, T2DM, and RA. Extracellular vesicles (EVs) are a method of intracellular signal transduction. Their function depends on surface expression, cargo, and the cell from which they originate.

In the article, were checked influences of microaeration, pH, and VSS (Volatile Suspended Solid) for sour cab-bage anaerobic digestion. Results fermentation of sour cabbage under the condition of small oxygen addition are presented in this research can be classified as dark fermentation or hydrogenotrophic anaerobic digestion. The investigations were carried out for two concentrations 5 g VSS /L and 10 g VSS /L of sour cabbage at pH 6.0. The oxygen flow rates (OFR) for 5 g VSS /L were in the range of 0.53 to 3.3 mL/h for obtaining 2% to 8% of oxygen. In cases of low pH and microaeration, ethylene production was observed at a level below 0.05% in biogas. The highest volume of hydrogen for 5 g VSS/L was obtained for flow rate 0.58 O2 mL/h, giving hydrogen concentration in biogas in the range of 0 to 20%. For VSS 5 g/L and oxygen flow rate 0.58 mL/h; 0.021 L of hydrogen is produced per gram of VSS. In this case, VSS 10 g/L and oxygen flow rate 1.4 mL/h at pH 6.0, 0.03 L of hydrogen is generated per gram. Microaeration from 0.58 mL/h to 0.87 mL/h was propitious for hydrogen production at 5 g VSS/L of sour cabbage and 1.4 mL/h for 10 g/L. Another relevant factor is the volatile suspended solid factor of sour cabbage that caused optimal hydrogen production at VSS 89.32%.

Background: This study investigated the effect of indirect air-cooling on the variation in intrapulpal temperature (ΔT) during different light-curing protocols of bulk-fill resin composites in molars with class V cavities. Methods: A nonretentive class V cavity was prepared in an upper molar. The intrapulpal temperature changes with and without air-cooling were recorded with type K thermocouple. The cavity was restored with bulk-fill resin composites: Tetric PowerFlow and Filtek Bulk-Fill Flow. The tooth was exposed to different light-curing protocols (n=5) using the Valo Grand light-curing unit: (i) high-intensity light-curing of 3200 mW/cm² (3 and 6 s) and (ii) moderate-intensity light-curing of 1000 mW/cm² (10 and 20 s). The ΔT data were subjected to two-way ANOVA, followed by Bonferroni post hoc test. Results: A significant increase in temperature was observed with the use of the high-intensity light-curing resin composite without indirect air-cooling. In addition, the application of air-cooling significantly decreased the temperature in all the groups except for the Tetric PowerFlow bulk-fill resin composite at 3 s of light-curing. Conclusion: Indirect air-cooling resulted in a lower increase in intrapulpal temperature during the light-curing of bulk-fill resin composites, making it an effective alternative for controlling the temperature rise in class V restorations with 1 mm of remaining dentin.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

The goal of our study was to examine the effect of regional characteristics of living environment on individual a priori and a posteriori dietary patterns of the Russian population. For the analysis, we used cross-sectional data from the Epidemiology of Cardiovascular Diseases in the Regions of the Russian Federation study of 2013-2014. The sample included 18,054 men and women 25-64 years of age from 12 regions. Based on the frequency of consumption of basic foods, four a posteriori empirical dietary patterns (EDPs), along with an a priori cardioprotective dietary pattern (CPDP) were identified. To describe the regional living environment, 5 regional indices were used. The adherence to the meat-based EDP was directly associated with deterioration of social living conditions and the more northerly location of the region of residence. The probability of CPDP increased with deterioration of social living conditions, an aggravation of demographic crisis, higher industrial development of the region, as well as with a decline in the economic development of the region, income and economic inequality of the population. We detected some gender-dependent differences in associations. The revealed patterns reflect the national dietary preferences of Russians, and regional indices characterize the effect of living environment.

Pine nuts are non-wood forest products (NWFP) with constantly growing market notwithstanding a series of phytosanitary issues and related trade problems. The aim of paper is to review the literature on the relationship between phytosanitary problems and trade development. Production and trade of pine nuts in Mediterranean Europe have been negatively affected by the spreading of Sphaeropsis sapinea (a fungus) associated to an adventive insect Leptoglossus occidentalis (fungal vector), with impacts on forest management activities, production and profitability and thus in value chain organization. Reduced availability of domestic production in markets with growing demand has stimulated the import of pine nuts. China has become a leading exporter of pine nuts, but its export is affected by a symptom associated to the nuts of some pine species: the ‘pine nut syndrome’ (PNS). Most of the studies embraced during the review are associated to PNS occurrence associated to the nuts of Pinus armandii. In the literature review we highlight the need for a comprehensive and interdisciplinary approach to the analysis of the pine nuts value chain organisation, where research on food properties and clinical toxicology be connected to breeding and forest management, forest pathology and entomology and trade development studies.

In this article, we consider a class of nonsmooth interval-valued multiobjective semi-infinite programming problems with vanishing constraints (in short, NIMSIPVC). We introduce the VC-Abadie constraint qualification (in short, VC-ACQ) for NIMSIPVC and employ it to establish Karush-Kuhn-Tucker (in short, KKT)-type necessary optimality conditions. Related to NIMSIPVC, we formulate interval-valued vector Lagrange type dual and scalarized Lagrange type dual problems. Subsequently, we establish weak, strong, and converse duality results relating NIMSIPVC and corresponding dual problems. In addition, we introduce the notions of saddle points for interval-valued vector Lagrangian and scalarized Lagrangian of NIMSIPVC. Moreover, we establish the saddle point optimality criteria for NIMSIPVC. Various non-trivial examples are provided to demonstrate the validity of established results. To the best of our knowledge, optimality conditions, Lagrange type duality, and saddle point optimality criteria for NIMSIPVC have not been investigated yet via Clarke subdifferentials.

Drone navigation is critical, particularly during the initial and final phases, such as the initial ascension, where pilots may fail due to strong external disturbances that could lead to a crash. In this ongoing work, a drone has been successfully trained to perform an ascent of up to 6 meters with external disturbances simulating wind pushing it up to 24 mph, with the DQN algorithm managing external forces affecting the system. It has been demonstrated that the system can control its height, position, and stability in all three axes (roll, pitch, and yaw) throughout the process. The learning process is carried out in the Gazebo simulator, which emulates interferences, while ROS is used to communicate with the agent.

The influence of small-scale processes at the ocean-atmosphere boundary layer such as spray and foam on the surface waves prediction is studied. Estimates of the effect of including the exact number of specific fragmentation "parachute" type in the spray on the resulting drag coefficient is shown. For the estimates, the numerical simulations within WAVEWATCH III wave model are performed. The parameterizations of wind input were tested within WAVEWATCH III wave model: default ST4 and ST6 parameterizations and the ST1 and ST6 parameterizations used together with the implemented drag coefficient parameterization. The proposed parameterization takes into account the presence of foam and spay. The obtained results are compared with the NDBC buoys data. The importance of small-scale processes for waves at hurricane winds prediction and the prospects for their inclusion in modern numerical wave models is shown.

We consider an alternative hypothesis of crater formation -- through an electric discharge machining (EDM) of the celestial bodies' surfaces. The source of the energy and the current itself may lie in the plasma infalling on a celestial body (from an extremely strong solar outburst or a nearby supernova). This mechanism may have been even more important than impact cratering in the early Solar System, with potential implications to the history of the dynamics of the System itself and solar activity in particular. In this light, the conclusion that shocked and metamorphosed minerals found within crater sites are evidence of hypervelocity impacts might be reconsidered. There are ambiguities that remain among sources of mineralogical formations. This study is ongoing with details of investigations supporting a new approach to crater formation not yet exhausted. Apart from mineralogical analysis and theoretical considerations regarding the large scale crater formation, we present a description of experimental studies of EDM acting at low pressures. Experimental results are made with crude setups and could easily be replicated on a larger scale with valuable research potential, as there is a well understood relation between the crater size and the energy needed for its production.

Agaricus bisporus is one of the most popular mushroom species in the world; however, mushrooms are highly susceptible to browning due to the absence of a protective cuticle layer and high respiration rate. The molecular mechanism underlying the process of mushroom browningneeds to be explored. Here, we analyzed the transcriptomic and metabolomic data from A. bisporusat ambient temperature. Specifically, a total of 263 significantly changed metabolites and 4492 differentially expressed genes were identified. Lipid metabolites associated with cell membrane degradation were predominantly up-regulated during ambient storage. Transcriptomic data further revealed the alterations of the expression of membrane lipid metabolism-related enzymes. Additionally, energy metabolic processes and products such as glycolysis and linoleic acid changed significantly during ambient storage, indicating their potential roles in the quality deterioration of A. bisporus. These findings provide new insights into the underlyingl ipidmetabolic mechanism of A. bisporus during postharvest ambient storage and will provide values for mushroom preservation techniques.

People wore clothes for warmth, survival and necessity in modern life as well but in modern era, eco-friendliness, shorten production time, design, and intelligence also matters. The seamless bonding technology strengthen the bond between fabrics in textiles, while Grey relational analysis (GRA) can be applied to fabrics to measure the relationship between data series and determine the closeness of each data series. In this study, polyurethane prepolymer, 2-Hydroxyethyl acrylate (2-HEA) as an end-capping agent, and n-octyl acrylate (ODA) as a photo-initiator were used to synthesize dual-curing polyurethane hot-melt adhesive. The Taguchi quality engineering and grey relational analysis used to discuss the influence of different mole ratio of NCO:OH, and the effect of the molar ratio of addition of octyl decyl acrylate on the mechanical strength. The Fourier transform infrared spectroscopy (FTIR) results showed the termination of prepolymer's polymerization reaction and the C=O peak intensity at 1730 cm-1 indicating the efficient bonding to main chain. The high molecular weight polymer (20,000-30,000) described by advanced polymer chromatography (APC) confirmed the polyurethane polymer bonded with octyl decyl acrylate to achieve the photo-thermosetting effect. The thermogravimetric analysis (TGA) results showed the thermal decomposition temperature of polyurethane hot melt adhesive also increased and highest pyrolysis temperature (349.89℃) for the polyhydric alcohols. The high value of shear strength (34.94 kg/cm2) as well as peel strength (1.68 kg/cm) were also observed in dual-cure photo-thermosetting polyurethane hot melt adhesive. The signal-to-noise ratio also used to generate the grey relational degree. It was observed that the best parameter ration of NCO: OH was 4:1 with 5 moles of monomer. The Taguchi quality engineering method was used to find the parameters of single quality optimization, and then the grey relation calculation was used to obtain the parameter combination of multi-quality optimization for thermosetting polyurethane hot melt adhesive. The study aims to meet the requirements of seamless bonding in textile factories and optimized experimental parameter design by setting target values can effectively increase production speed, reduce processing time and costs as well.

The soil organic matter (SOM) content and stability in natural gypsum soils and soils from mining/industrial areas were compared, in terms of their physical, chemical and micromorphological properties, to determine whether the old brownfield soils were acting as carbon (C) sinks, counteracting increasing carbon dioxide concentrations in the atmosphere. The mining/industrial soils were 50–400 years old, so had been left sufficiently long for full self-restoration. Despite having very different origins, both natural and brownfield soils stored similar amounts of SOM, and had similar pH values, calcium carbonate contents and textures. They were also fully covered with similar grass plant communities. The mining/industrial soils exhibited similar microstructures to the gypsum soils and were often quite porous. The most striking difference between them and the natural gypsum soils was that the mining/industrial soils were strongly polluted with zinc, lead and cadmium. The 50-year-old brownfield soils differed from the others in terms of having a lower state of SOM transformation, with a much higher C/N ratio, lower aggregate water resistance index, lower dehydrogenase activity and greater areas of undecomposed or slightly decomposed plant residues. These parameters in the older (150–400 years) brownfield soils were similar to those of the natural soils.

Microalgae and their bioproducts hold significant potential across various applications, for instance, in wastewater remediation, CO2 fixation, and the synthesis of nutraceuticals, pharmaceuticals, and biofuels. The production of these organisms heavily relies upon environmental conditions, including factors like temperature, light, and nutrient supply, which can significantly impact growth. Furthermore, the limitations in nutrients or certain extreme environments can result in productivity increases. As such, microalgae growth systems have become a critical consideration for both research and industry. Both open and closed systems, such as raceway ponds and photobioreactors, respectively, have their own advantages and drawbacks in microalgae cultivation. However, for microalgae growth, photobioreactors may address most concerns, as the system has a lower risk of contamination and can deliver specific growth factors in a controlled manner. This review will summarize the growth and incubation factors of microalgae and the uses of bioreactors in both research and industrial capacities.