The cyclic load applied to civil and mining structures can lead to a reduction of the materials’ strength, different from that which would occur with a monotonous load. Numerous cases can be found where the decay of the rock parameters subjected to this type of stress leads to progressive or sudden collapse: among them, tunnel walls, pillars and slabs in mining operations, roads with a heavy vehicle transit, abutments of bridges and dams can be quoted. The topic can therefore be fundamental for a correct structural design, to avoid problems during the life of the structure. However, given the heterogeneity of the rock materials and the difficulty of their characterization under this aspect, an unequivocal analysis is hardly achievable. Then, the discussion initially develops through a general historical review of the concept of fatigue, with a synthetic collection of case histories. The laboratory tests on rock samples are then examined and the most important results obtained are discussed. Finally, a comparison between different types of tests is proposed. The experimental data are expressed through the Wӧhler diagram. The goal is to fill the lack of design codes or standards in the field of cyclic stresses applied to rock materials, the understanding of its effect being of great interest in order to apply suitable parameters in the design phase.

This paper is concerned with bump-less transfer of parametrized disturbance observer based controller (DOBC) with Individual Pitch Control (IPC) strategy for full load operation of wind turbine. Aerodynamic cyclic loads are reduced by tuning multivariable DOBC with the objective to reduce output power fluctuation, tower oscillation and drive-train torsion. Furthermore tower shadow and wind shear effect are also mitigated using parametrized controller. A scheduling mechanism between two DOBC is developed and tested on Fatigue, Aerodynamics, Structures, and Turbulence ( FAST) code model of National Renewable Energy Laboratory (NREL)’s 5 MW wind turbine. The closed-loop system performance is assessed by comparing the simulation results of proposed controller with a fixed gain and Linear Parameter Varying (LPV) DOBC with Collective Pitch Control (CPC) for full load operation. It is tested with step changing wind to see the behavior of the system under step change with wind shear and tower shadow (cyclic load) effects. Also turbulent wind is applied to see the smooth transition of the controllers. It can be concluded from the results that the proposed parametrized control DOBC with IPC shows smooth transition from one controller to another by interpolation. Moreover fatigue of the gear and tower due to wind shear and tower shadow effects are reduced considerably by the proposed controller as compared to collective pitch control.

Abstract: Congenital cytomegalovirus (cCMV) infection poses significant risks to fetal development, particularly affecting the nervous system. This study reports a fetal autopsy case, examining cCMV infection and focusing on CMV DNA measurements in various fetal organs before formalin fixation, a novel approach for comprehensive CMV DNA evaluations in fetal organs affected by cCMV. A 20-week-old male fetus was diagnosed with cCMV following the detection of CMV DNA in ascites obtained via abdominocentesis in utero. After termination of pregnancy, multiple organs of the fetus, including the cerebrum, thyroid gland, heart, lungs, liver, spleen, kidneys, and adrenal glands, were extracted and examined for CMV DNA loads using real-time polymerase chain reaction. Histopathological examination involved hematoxylin-eosin and CMV-specific immunostaining. A correlation was found between CMV DNA loads and pathology, with higher CMV-infected cell numbers observed in organs positively identified with both staining methods, exhibiting CMV DNA levels of ≥1.0 × 104 copies/mL, compared to those detected solely by CMV-specific immunostaining, where CMV DNA levels ranged from 1.0 x 103 to 1.0 x 104 copies/mL. These results highlight a quantifiable relationship between organ infection extent and CMV DNA concentration, providing insights into cCMV pathogenesis and potentially informing future diagnostic and therapeutic strategies for cCMV infection.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Dear Ladies and Gentlemen, I thank you for suggesting to submit the manuscript with the title “Insulin resistance develops due to an imbalance in the synthesis of cyclic AMP and the natural cyclic AMP antagonist prostaglandylinositol cyclic phosphate (cyclic PIP)” to the Editorial Board of the MDPI journal Stresses, and I ask for consideration to publish it in the journal Stresses. It was previously submitted to the MDPI journal Int. J. Mol. Sci. (IJMS-195 6513), but it was found that 1) it would not fit within the scope of this special edition and 2) it would primarily deal with cyclic PIP and would have not enough literature citation on the topic insulin resistance. The present version of the manuscript is improved, but the content is the same. The goal of this review is not to write again a summary on nearly all reports on insulin resistance as this was done by Dr. Petersen and Dr. Shulman, whose review has 961 literature citations. The present manuscript compiles what is known on cyclic PIP in relation to insulin resistance and the reason of writing this manuscript was that the discovered facts on cyclic PIP synthesis allow to suggest how insulin resistance most likely starts. Hitherto, reports on insulin resistance did not come close to this question. I am convinced that the manuscript makes an essential contribution to the question what causes the development of insulin resistance, and I have to say that stress overload is one of the reasons. Unfortunately, I have to mention a topic, about which I do not like to talk. Years ago, research groups postulated with rigor that the mediator of insulin action would be a peptide and then they suggested various, extracellularly synthesized glycans as mediators. They caused confusions and a high degree of disbelief in the matter of mediators of insulin action. In my review on cyclic PIP in IUBMB Life from 2020, I wrote in the introduction that cyclic PIP should not be confused with these mediators. But I cannot write this in the introduction of every report. I am keeping fingers crossed so that the editor in charge will find fair and openminded reviewers. Last not least I confirm that neither the manuscript nor any part of its content is currently under consideration or published in another journal. Kind regards, Henrich Wasner, PhD, BioReg Biopharm, TiLab; University of Illinois at Chicago; 2242 West Harrison St., Ste. 201, Chicago, Il 60612; USA

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

If "quantization is an art" then it can be greatly rened by adopting cyclic time formalism. In past papers we have proven the effectiveness of a formulation of physics based on cyclic relativistic time. Now we can demonstrate in a general way, by using theorems of Geometric Quantization, that the Poisson brackets of intrinsically cyclic time dynamics directly imply the ordinary canonical commutation relations and the other Dirac's rules of canonical Quantum Mechanics. In other words, according to our result, canonical quantization is an implicit way of imposing intrinsically cyclic time dynamics without explicitly saying that time is a cyclic dimension.

This article is devoted to the problem of genetically coding of inherited cyclic structures in biological bodies, whose life activity is based on a great inherited set of mutually coordinated cyclic processes. The author puts forward and arguments the idea that the genetic coding system is capable of encoding inherited cyclic processes because it itself is a system of cyclic codes connected with Boolean algebra of logic. In other words, the physiological processes in question are cyclical because they are genetically encoded by cyclic codes. In support of this idea, the author presents a set of his results on the connection of the genetic coding system with cyclic Gray codes, which are one of many known types of cyclic codes. This opens up the possibility of using for modeling inherited cyclic biostructures those algebraic and logical theories and constructions that are associated with Gray codes and have long been used in engineering technologies: Karnaugh maps, Hilbert curve, Hadamard matrices, Walsh functions, dyadic analysis, etc. Additionally, the connections of these constructions with statistical rules of genomic DNAs and binary-genomic numbers are considered.

The paper presents a review of currently available evaluations of the effects of continuously increasing anthropogenic loads on water resources. The increase in the fluxes of elements and compounds into the environment, such as the emission of greenhouse gases and dispersion of nutrients (nitrogen and phosphorus), acidifying gases, and toxic elements and compounds that adversely affect the water quality are considered. The significance of fresh waters as a life support factor of the human populations is demonstrated. Examples are presented to illustrate how key anthropogenic induced processes develop in land waters under the effect of anthropogenic loads, as exemplified by the Russian Kola regions. Climate warming and the increasing dispersion of elements are demonstrated to result in the eutrophication of surface waters even in areas remote from anthropogenic impacted regions. Although the emissions of acidifying gases diminish, the waters are still acidified in acid-vulnerable areas, and the chemical compositions of the waters have been significantly modified over the past decades, which indicates that the changes in the chemical composition of the waters are of irreversible. A new feature of the waters is distinguished: the toxicity of the habitats for aquatic organisms. Arguments are presented for establishing a theoretical approach for evaluating critical loads.

In this paper, spacetime is defined as the absolutely invariant homogeneous "coordinate spacetime" frame and its modulation by the relatively variable non-homogeneous "metric spacetime" under its constraints. This modulation is caused by matter and motion, and carries the function of transmitting interactions, reflecting the diffeomorphism invariance and Lorentz invariance. This inhomogeneous spacetime concept makes the medium nature of spacetime more obvious and avoids the problem of "path dependence" caused by the concept of curved spacetime. In this paper, it is argued that all energy-momentum has internal spatio-temporal properties, and all interactions must be transmitted through spacetime metrics. On this basis, a converging and dispersing cyclic multiverse model is proposed. This model of the universe is inevitable as long as there are two macroscopic manifestations of the matter of the universe, namely, gravitation induced convergence and "explosive" dispersion caused by different factors. The new cosmic model matches the observed accelerated "expansion" of the universe and no longer requires the dark energy hypothesis.

The International System of Units (SI) was adopted in 1960 as a universal measuring system to be used for all areas of science. Sports Science papers have shown lots of inaccurate and inappropriate terms for quantification of athletes’ performance and the psychobiological responses to exercise (e.g., internal load). In biomechanics, external and internal loads are forces acting externally and internally, inducing stress and strain in the biological tissues. Therefore, the current review present simple proposals to correct the inappropriate terms: 1) do not use the term external load when referring to the assessment of exercise time, distance, displacement, speed, velocity, acceleration, torque, work, power, impulse, etc.; 2) do not use the term internal load when referring to the assessment of psychobiological stress markers (i.e., session rating of perceived exertion, heart rate, blood lactate, oxygen consumption, etc.); 3) do not use the term impulse when expressing other calculus than integrating force with respect to time, and neither strain, when expressing other phenomena than the body deformation. Instead, the term exercise intensity is universal and can be used to describe all forms of exercise. Finally, duration should precisely be described according to physical quantities (e.g., time, distance, displacement, speed, velocity, acceleration, force, torque, work, power, impulse, etc.) and the units accomplish by use of the SI. These simple quantifications can be performed for the exercises, sessions, microcycles, mesocycles and macrocycles of the athletes. Such standardization will provide a consistent and clear communication among sports scientists and all areas of science.

Antimicrobial peptides (AMPs) are promising tools for combating microbial resistance. However, their therapeutic potential is hindered by two intrinsic drawbacks – low target affinity and poor in vivo stability. Macrocyclization, a process that improves the pharmacological properties and bioactivity of peptides, can address these limitations. As a result, macrocyclic peptides represent attractive drug candidates. Moreover, many drugs are macrocycles that originated from natural product scaffolds, suggesting that nature offers solutions to the challenges faced by AMPs. In this review, we explore natural cyclic peptides from the DBAASP database. DBAASP is a comprehensive repository of data on antimicrobial/cytotoxic activities and structures of peptides. We analyze the data on small (≤25 AA) ribosomal and non-ribosomal cyclic peptides from DBAASP according to their amino acid composition, bonds used for cyclization, targets they act on, and mechanisms of action. This analysis will enhance our understanding of the small cyclic peptides that nature has provided to defend living organisms.

This paper presents performed Ansys numerical simulation on WindFloat structures. It contributes to the methodology of calculation based on CFD instruments to study the movements of the waves on semi-submersible stationary structures and highlights the importance of using RAO functions. RAO numerical approach developed can be applied to design semisubmersible WindFloat structures in order to fulfill essential requirements regarding operational safety and design. Numerical methodology was designed in accordance marine loads and the I.T.T.C. recommendations. The numerical RAO results for regular wave movements include many elements for the semi-submergible structure. Close results to open sea operation can be achieved by constant improvement in numerical simulation methodologies. The work opens the way for further hydrodynamic development on irregular waves for realistic hydrodynamic and structural response of the actual semi-submersibles at sea. The results demonstrate the accuracy of RAO function approach for specific WindFloat in Jonswap spectrum.

Renewable Energy Communities (RECs) are emerging as an effective concept and model to empower the active participation of citizens on the energy transition, not only as energy consumers, but also as promoters of environmentally friendly energy generation solutions. This paper aims to contribute to the management and optimization of individual and community Distributed Energy Resources (DER). The solution follows a price and source-based REC management program, in which consumers day-ahead flexible loads (Flex Offers) are shifted according to electricity generation availability, prices and personal preferences, to balance the grid and incentivize user participation. The heuristic approach used in the proposed algorithms allows the optimization of energy resources in a distributed edge and fog approach with a low computational overhead. The simulations performed using real world energy consumption and flexibility data of a REC with 50 dwellings show an average cost reduction of 10.6% and an average increase of 11.4% in individual self-consumption. Additionally, the case-study demonstrates promising results regarding grid load balancing and the introduction of intra-community energy trading.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

Nanostructured dipeptide self-assemblies exhibiting quantum confinement are of great interest due to their potential applications in the field of materials science as optoelectronic materials for energy harvesting devices. Among those, aromatic cyclo-dipeptides containing the amino acid tryptophan are wide-band gap semiconductors displaying high mechanical rigidity, photoluminescence and piezoelectric properties to be used in power generation. In this work, we report the fabrication of hybrid systems based on chiral cyclo-dipeptide L-Tryptophan- L-Tryptophan incorporated into biopolymer electrospun fibers. The micro/nanofibers contain self-assembled nanospheres embedded into the polymer matrix are wide-band gap semiconductors (gap energy 3.8 eV), display blue photoluminescence and relevant piezoelectric and pyroelectric properties with coefficients as high as 57 pCN-1 and 35×10-6 Cm-2k-1, respectively. They are therefore promise systems for thermal sensing and energy harvesting applications.

A novel theoem is presented about a circle with four antipodal points, arbitrarily ordered counterclockwise (or clockwise), in a Euclidean plane.

The regulation of multiple bacterial phenotypes was found to depend on different cyclic di-nucleotides (CDNs) that constitute intracellular signalling second messenger systems. Most notably, c-di-GMP, along with proteins related to its synthesis, sensing and degradation, was identified as playing a central role in the switching from biofilm to planktonic modes of growth. Recently, this world has been under expansion, with the discoveries of other signalling CNDs in bacteria (c-di-AMP and cGAMP) and also in eukaryotes, novel protein and RNA receptors of CDNs, and the numerous functions related to these molecules. In this work, we comprehensively review and analyse the structural biology data about the systems that bacteria use to synthesise and recognise CDNs, detailing their interactions at molecular level with their products/ligands. Additional interesting observations were made, including that different receptor types can bind CDNs in similar conformations and that, based on genomic data, different CDN second messenger systems may coexist in many organisms. The large amount of sequence and structural data available allows a broad view of the importance of CDNs in bacteria, but how cells coordinate these molecules to ensure adaptation to changing environmental conditions is still open for much further exploration.

The tribology behavior, tribofilm formation and structure evolution of polytetrafluoroethylene (PTFE) filled with α-Al2O3 and SiO2 nanoparticles during sliding against steel counterparts under different loads were studied. It is found that both composites exhibit good wear resistance across the pressure of 1 MPa to 10 MPa, with the α-Al2O3/PTFE composite demonstrates better performance stability compared to the SiO2/PTFE composite. The high wear resistance is attributed to the formation of tribofilms at the friction interface. For the α-Al2O3/PTFE, an island-like tribofilm is formed with a thickness ranging from 100 to 200 nm, while the tribofilm of the SiO2/PTFE composite is thinner, measuring approximately 50 to 100 nm, and manifest a striped pattern. The chemical composition, both at the surface and subsurface levels, as well as the morphology of the tribofilms were studied using FTIR spectrometry, X-Ray photoelectron spectroscopy (XPS), and FIB-TEM. It is found that the difference in thickness and microstructure of the tribofilms for the two composites is mainly due to the tribochemistry of the nanoparticles. The α-Al2O3 nanoparticle plays a "cohesion" role during the formation of the tribofilm, which facilitates the formation of a thicker, more uniform, and stronger adhered tribofilm on the metallic counterpart, making it more robust against higher shear stress.

Thermostatically controlled loads have great potential to make a significant contribution to improving energy efficiency in the building sector, which is responsible for 40% of greenhouse gas emissions in the EU. This, in addition to the environmental damage, represents a huge expense in the electricity bill. Therefore, it is very important to train engineers on how to design energy management systems for TCLs. With this goal in mind, it would be very useful to have a simulation-based educational tool (SBET) to understand thermostatically controlled loads, their characteristics and possibilities in energy efficiency. In addition, it would be very useful if this tool could be introduced in engineering curricula to help students to be better trained and enter the labor market with more opportunities. Based on the shortcomings detected, this work develops a SBET specifically designed to teach about TCLs (SBET-TCLs), both about their intrinsic characteristics and their better management. To verify the developed SBET-TCL, it has been tested in a real scenario: A survey was carried out among the students of the subject 'Alternative Energy Sources' of the degrees of Industrial Engineering. The results show that the use of SBET-TCL has very positive effects on the learning process.

Background: Runners have high incidence of repetitive load injuries, and habitual runners often use smartwatches with embedded IMU sensors to track their performance and training. If accelerometer information from such IMUs can provide information about individual tissue loads, then running watches may be used to prevent injuries. Methods: We investigate a combined physics-based simulation and data-based method. 285 running trials from 76 real runners are subjected to physics-based simulation to recover forces in the Achilles tendon and patella ligament, and the collected data are used to train and test a data-based model using elastic net and gradient boosting methods. Results: Correlations up to 0.95 and 0.71 for the patella ligament and Achilles tendon forces, respectively, are obtained, but no single best predictive algorithm can be identified. Conclusions: Prediction of tissues loads based on body-mounted IMUs appears promising but requires further investigation before deployment as a general option for users of running watches to reduce running-related injuries.

Renovation, restoration, remodeling, refurbishment, and retrofitting of build-ings often imply modifying the behavior of the structural system. Modification sometimes includes applying forces (i.e., concentrated loads) to beams that before were subjected to distributed loads only. For a reinforced concrete structure, the new condition causes a beam to bear a concentrated load with the crack pattern that was produced by the distributed loads that acted in the past. If the concentrated load is applied at or near the beam’s midspan, the new shear demand reaches the maximum around the midspan. But around the midspan, the cracks are vertical or quasi-vertical, and no inclined bar is present. So, the actual shear capacity around the midspan not only is low, but also can be substantially lower than the new demand. In order to bring the beam capacity up to the demand, fiber-reinforced-polymer composites can be used. This paper presents a design method to increase the concentrated load-carrying capacity of reinforced concrete beams whose load distribution has to be changed from distributed to concentrated, and an analytical model to pre-dict the concentrated load-carrying capacity of a beam in the strengthened state.

Cyclic neutropenia is a rare hematological condition characterized by periodic fluctuations in neutrophil counts, with a 21-day periodicity. Clinical presentation varies from mild to severe forms of the disease, with the onset of recurrent fever, painful oral ulcers, recurrent bacterial infections, peritonitis and septic shock. The availability of granulocyte colony-stimulating factor (G-CSF) has revolutionized the management and natural history of this disease, regulating the proliferation, differentiation and maturation of the progenitor cells, reducing the duration of neutropenia. Inflammatory bowel disease (IBD), including Crohn’s disease (CD) and ulcerative colitis (UC), is a group of chronic pathologies with involvement of the gastrointestinal tract. Symptoms include diarrhea, abdominal pain, fever, weight loss and extraintestinal manifestations (EIMs). In recent years, the focus of IBD therapy, including conventional therapies and biological therapies, has moved from treatment of symptoms to "deep remission" of the disease. The association between cyclic neutropenia and CD is rarely reported in the literature. Here, we describe two case reports of patients who underwent surgery because of diagnosis of complicated CD. After surgery, because of persistent neutropenia, the hematologist consultant confirmed suspicions of cyclic neutropenia and therapy with G-CSF was started with benefits, underlining the crucial importance of proper differential diagnosis.

In the increasingly complex environment of downhole working conditions such as frequent opening and closing of oil and gas wells, acidification/multi-stage fracturing, steam huff and puff, and strong injection and production, the traditional casing string design method standards based on strength design have gradually highlighted their limitations. It is necessary to formulate string design method standards that consider the full life cycle of wells such as drilling and completion, fracturing, and production operations. Starting from the analysis of the advantages and disadvantages of traditional casing string design methods, this paper presents the characteristics of the strain design methods and seal design methods that have been formulated for the life cycle of the string. The strain design method breaks through the traditional design concept and allows the design concept of controllable deformation of the pipe string. The sealing design method is currently the only standard method for the design of tubing strings. At the same time, it further proposes to consider the trend of pipe strength deterioration and establish a time dimension-based life cycle pipe string design method standard, which effectively solves the safety problem of pipe string design in production and operation.

Cellular response to mechanical stimuli is a crucial factor for maintaining cell homeostasis. The interaction between extracellular matrix and mechanical stress plays a significant role in organ-izing the cytoskeleton and aligning cells. Tools that apply mechanical forces to cells and tissues, as well as those capable of measuring the mechanical properties of biological cells, have greatly contributed to our understanding of fundamental mechanobiology. These tools have been exten-sively employed to unveil the substantial influence of mechanical cues on the development and progression of various diseases. In this report, we present an economical and high-performance uniaxial cell stretching device. This paper reports the detailed operation concept of the device, ex-perimental design, and characterization. The device was tested with MDA-MB-231 breast cancer cells. Experimental results agree well with previously documented morphological changes re-sulting from stretching forces on cancer cells. Remarkably, our new device demonstrates compa-rable cellular changes within a 30-minute compared to the previous 2-hour stretching duration. Moreover, the device design incorporates an open-source software interface, facilitating conven-ient parameter adjustments such as strain, stretching speed, frequency, and duration. Its versatil-ity enables seamless integration with various optical microscopes, thereby yielding novel insights into the realm of mechanobiology.

As a consequence of a three-stage synthesis from terephthalic aldehyde, a series of 3,3 '- (1,4-phenylene) perchlorates including methyl, hydrogen, acetyl, bromio, methoxy and nitro groups (R = Br, H, Me). The matching formazans were reacted with formalin in dioxane in the presence of perchloric acid to produce tetrazin ium salts. Formazans were synthesized by reacting terephthalic aldehyde phenylhydrazone with ar ene diazonium tosylates in a DMF/pyridine combination. The use of ar ene diazonium tosylates greatly simplified the separation and purification of formazans. The p henylhydrazone was produced in aqueous dioxane using the usual approach from terephthalic aldehyde and phenylhydrazine/hydrochloric acid. Individual f ormazans and tetrazinium perchlorates were isolated and characterized by elemental analysis, IR, NMR, UV spectroscopy. The electrochemical reduction of tetrazinium perchlorates was investigated using cyclic voltammetry (CV). Thus, all salts in the cathode region have two one-electron reduction peaks, which are connected to the sequential production of a radical cation and a biradical. It was discovered that donor substituents (R: OMe, Me) in the aromatic ring at position 1 accelerate tetrazinium cation reduction, whereas acceptor substituents (R: NO₂, COMe,) inhibit this process. On this premise, it was proposed that in the presence of donor substituents in the aromatic ring at position 1, the matching bis-verdazyl radicals should be easily generated. As a result, 3,3'- (1,4-phenylene) perchlorates are possible antecedents of symmetric biradical systems based on verdazyl radicals.

One of the most important problems of geotechnical engineering is the design of pile foundations. Piles are generally designed for vertical and horizontal static loads. However, it is important to design piles against dynamic loads in regions with high seismicity. This study verified a centrifuge experiment obtained from the literature with a finite element program. With the kinematic interaction analyses made for this purpose, the effect of parameters such as layered soil, groundwater, pile stiffness, and earthquake acceleration were investigated numerically. According to the results obtained, it was understood that the earthquake magnitude is the most important parameter in kinematic interaction analyses. In addition, in layered soil conditions, the fact that 75% of the pile length is in the weak soil creates the most unfavorable situation. It has been observed that pile stiffness and groundwater level also have certain effects on the kinematic interaction.

Background: The question of whether children are less likely to pass on SARS-CoV-2 is important for planning society’s response to the pandemic. A document available on the Charité hospital website has not been formally published but is frequently referred to as supporting the notion that viral loads are similar in children and adults. Methods: The summary data from this document was extracted and used to produce summary statistics for three age groups: younger children (ages up to 11), older children (ages 12 to 19) and adults (ages 20 and above). Viral loads between the two children’s groups and the adult group were compared using Welch’s t test, which only requires group means and standard deviations and which is robust against moderate departures from normality. Findings: Viral loads were significantly lower than in adults for both younger children (p=0.04) and older children (p=0.04). Overall, viral loads were lower in children than adults (p=0.005). Interpretation: For both younger and older children, on average those with detectable SARS-CoV-2 have significantly lower viral loads than adults. Funding: No funding was received for this analysis.

A cyclic antipodal points of a circle is a pair of points that are the intersection of the circle with a diameter of the circle. A recent proof of Ptolemy’s Theorem, simultaneously in both (i) Euclidean geometry; and (ii) the relativistic model of hyperbolic geometry (which is identified with the Klein model of hyperbolic geometry), motivates in this article the study of four cyclic antipodal points of a circle, ordered arbitrarily counterclockwise. The translation of results from Euclidean geometry into hyperbolic geometry is obtained by means of hyperbolic trigonometry, called gyrotrigonometry, to which Einstein addition gives rise. Formulas that extend the Pythagorean formula in both Euclidean and hyperbolic geometry are obtained as byproducts

The paper presents the results of experimental studies and mathematical modeling of the effect of stress accumulation in thermosetting epoxy polymer "hot" curing on anhydride hardener. Stress accumulation occurs under cyclic thermomechanical action in a locked rod, similar effects are observed, for example, in thermoplastic elements subjected to the combined effect of mechanical loads and variable temperatures. Experimental results have shown that under cyclic thermomechanical loading during exploitation it is possible to accumulate residual stresses in the thermosetting polymer. A multi-element structural mathematical model with memory for thermomechanical load, which allows to consider the accumulation of residual thermal stresses, has been proposed. The results of modeling and experiment are compared. Based on the results, corrections are made in the approach to the application of this model to thermosetting polymers such as the epoxy resin under study. Considering the corrections, a good agreement (the difference is from 1 to 6%) with the results of experimental determination of stresses under complex cyclic thermomechanical load was obtained.

Diffusion-controlled cyclic voltammograms at fast scan rates show peak shifts as well as decreases in the peak currents from the predicted diffusion-controlled currents especially when currents are large in low concentration of supporting electrolyte. This has been conventionally recognized as an IR-drop effect by solution resistance on the peaks as well as heterogeneous kinetics. It is also brought about by negatively capacitive currents associated with charge transfer reactions. The reaction product generates dipoles with counterions to yield a capacitance, of which current flows oppositely to that of the double layer capacitance. The three effects are specified here in the oxidation of a ferrocenyl derivative by fast scan voltammetry. The expression for voltammograms complicated with IR-drop is derived analytically, and yields deformed voltammograms. The peak shift is approximately linear with the IR-term, but exhibits a convex variation. Dependence of some parameters on the peaks by the IR-drop is compared with those by the negative capacitance. The latter is more conspicuous than the former under conventional conditions. The two effects cannot be distinguished specifically except for variations of conductance of the solution.

We present a Quantum Space Model (QSM) of the evolution of the universe based on the theory that space consists of energy quanta from which it began. We used the Friedmann equations to trace its history and show that Dark Energy is the energy of space which caused its accelerating expansion.The universe started from a quanta of space which was triggered by quantum fluctuations that caused the Big Bang. It then expanded and cooled undergoing phase transitions to radiation, fundamental particles, and matter. Matter grew into galaxies, and was consolidated by gravity into Black Holes, ending in a Big Crunch and Deep Freeze inside a Black hole at 1.380 trillion years. Fluctuations caused a new Bang to start another cycle in its life. If the Law of Conservation of Energy is universal, then the cosmos is eternal. Our results support the theoretical predictions of a cyclic universe by Steinhardt and associates, as well as Penrose. Space and energy are equivalent as embodied in the Planck energy equation. They are the two most fundamental quantities that govern cosmic evolution. The two principal long range forces are the gravitational force and the space force,which maybe the fifth force in the universe. They provide the clockwork mechanism operating our cyclic universe.

Performance of the overhead squat may affect golf swing mechanics associated with golf-related low back pain. This study investigates the difference in lumbar kinematics and joint loads during the golf downswing between golfers with different overhead squat abilities. Based on the per-formance of the overhead squat test, 21 golfers aged 18 to 30 years were divided into the highest-scoring group (HS, N=10, 1.61 ± 0.05 cm, and 68.06 ± 13.67 kg) and lowest-scoring group (LS, N=11, 1.68 ± 0.10 cm, and 75.00 ± 14.37 kg). Data collection used a motion analysis system, two force plates, and TrackMan. OpenSim software was used to simulate the joint loads for each lum-bar joint. An independent t-test was used for statistical analysis. Compared to golfers demonstrat-ing limitations in the overhead squat test, golfers with better performance in the overhead squat test demonstrated significantly greater angular extension displacement on the sagittal plane, smaller lumbar extension angular velocity, and smaller L4-S1 joint shear force. Consequently, the overhead squat test is found to be a useful index to reflect lumbar kinematics and joint loading patterns during the downswing, and provides a good training guide reference for reducing the risk of a golf-related low back injury

Cyclic vomiting syndrome (CVS) is a frequently disabling condition defined by severe, discrete, stereotypical episodes of nausea and vomiting. In our previous report [1], a candidate gene list was evaluated in a group of 80 unrelated participants with CVS with extensive genetic sequencing (whole exome/genome). Twenty-two good candidate genes for CVS association were identified, from which a cellular model of aberrant cation transport and energy metabolism was proposed. Herein, we present additional clinical information on those 80 participants, including eight case reports to highlight general principles and clinical practices. Our participants demonstrate substantial phenotypic and genotypic heterogeneity in CVS, including a propensity for specific co-morbidities in the participants and relatives, evolution towards episodes in which vomiting is less apparent, labeling with “non-organic” diagnoses, multiple genes, polygenic inheritance, and association with variants not designated as Pathogenic. Our case reports illustrate how genetic information can guide clinical management and argue to the high clinical utility of appropriate genetic testing and analysis in CVS. Expression profiling of our 22 candidate genes suggests an anatomical model in a unit defined by vagal afferents and adjacent cells. Our models are consistent with multiple current hypotheses of CVS and the efficacy of commonly-recommended treatments.

We characterize the form of the order divisor graph of cyclic groups based on the group order. Furthermore, we describe some topological indices of the order divisor graph of cyclic groups, including the Wiener index, Harary index, first Zagreb index, and second Zagreb index.

The formation of high-melting-point Cu₆Sn₅ interconnections is crucial to overcome the collapse of Sn-based micro-bumps and produce reliable intermetallic interconnections in three-dimensional (3D) package. However, because of the multiple reflows in 3D package manufacturing, Cu₆Sn₅ interconnections will experience the cyclic polymorphic transitions in the solid state. The repeated and abrupt change in the Cu₆Sn₅ lattice due to the cyclic polymorphic transitions can cause extreme strain oscillations, producing damages at the surface and in the interior of the Cu₆Sn₅ matrix. Moreover, because of the polymorphic-transition-induced grain splitting and superstructure phase formation, the reliability of Cu₆Sn₅ interconnections will thus face great challenges in 3D package. In addition, the Cu₆Sn₅ polymorphic transition is structure-dependent, and the η′↔η polymorphic transition will occur at the surface while the η′↔ηs↔η polymorphic transition will occur in the deep matrix. Our results can provide in-depth understandings of structural evolution and damage mechanism of Cu₆Sn₅ interconnections in real 3D package manufacturing.

Natural products from plants such as, chemopreventive agents attract huge attention because of their low toxicity and high specificity. The rational drug design in combination with structure based modeling and rapid screening methods offer significant potential for identifying and developing lead anticancer molecules. Thus, the molecular docking method plays an important role in screening a large set of molecules based on their free binding energies and proposes structural hypotheses of how the molecules can inhibit the target. Several peptide based therapeutics have been developed to combat several health disorders including cancers, metabolic disorders, heart-related, and infectious diseases. Despite the discovery of hundreds of such therapeutic peptides however, only few peptide-based drugs have made it to the market. Moreover, until date the activities of cyclic peptides towards molecular targets such as protein kinases, proteases, and apoptosis related proteins have never been explored. In this study we explore the in silico kinase and protease inhibitor potentials of cyclosaplin as well as study the interactions of cyclosaplin with other cancer-related proteins. Previously, the structure of cyclosaplin was elucidated by molecular modeling associated with dynamics that was used in the current study. Docking studies showed strong affinity of cyclosaplin towards cancer-related proteins. The binding affinity closer to 10 indicated efficient binding. Cyclosaplin showed strong binding affinities towards protein kinases such as EGFR, VEGFR2, PKB and p38 indicating its potential role in protein kinase inhibition. Moreover, it displayed strong binding affinity to apoptosis related proteins and revealed the possible role of cyclosaplin in apoptotic cell death. The protein-ligand interactions using LigPlot displayed some similar interactions between cyclosaplin and peptide-based ligands especially in case of protein kinases and a few apoptosis related proteins. Thus, the in silico analyses gave an insight of cyclosaplin as a potential apoptosis inducer and protein kinase inhibitor.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

The unexploited unification of general relativity and quantum physics is a painstaking issue that prevents physicists to properly understanding the whole of Nature. Here we propose a pure mathematical approach that introduces the problem in terms of group theory. Indeed, we build a cyclic groupoid (a nonempty set with a binary operation defined on it) that encompasses both the theories as subsets, making it possible to join together two of their most dissimilar experimental results, i.e., the commutativity detectable in our macroscopic relativistic world and the noncommutativity detectable in the quantum, microscopic world. This approach, combined with the Connes fusion operator, leads to a mathematical framework useful in the investigation of relativity/quantum mechanics relationships.

Peptide-based opioid ligands are important candidates for the development of novel, safer, and more effective analgesics to treat pain. To develop peptide-based safer analgesics, we synthesized a mixture-based cyclic pentapeptide library containing a total of 24,624 pentapeptides and screened the mixture-based library samples using a 55 °C warm-water tail-withdrawal assay. Using this phenotypic screening approach, we deconvoluted the mixture-based samples to identify a novel cyclic peptide Tyr-[D-Lys-Dap(Ant)-Thr-Gly] (CycloAnt), which produced dose- and time-dependent antinociception with an ED50 (and 95% confidence interval) of 0.70 (0.52-0.97) mg/kg i.p. mediated by the mu-opioid receptor (MOR). Additionally, higher doses (≥ 3 mg/kg, i.p.) of CycloAnt antagonized delta-opioid receptors (DOR) at least 3 hours. Pharmacological characterization of CycloAnt showed the cyclic peptide did not reduce breathing rate in mice at doses up to 15 times the analgesic ED50 value, and dramatically less hyperlocomotion than the MOR agonist, morphine. While chronic administration of CycloAnt resulted in antinociceptive tolerance, it was without opioid-induced hyperalgesia and significantly reduced signs of naloxone-precipitated withdrawal suggestive of reduced physical dependence as compared to morphine. Collectively, the results suggest this dual MOR/DOR multifunctional ligand is an excellent lead for the development of peptide-based safer analgesics.

Fungal infections pose a significant threat to human health, particularly in immunocompromised individuals. Due to several factors, such as the inappropriate use of antimicrobial drugs, the emergence of resistance in microorganisms, and increasing demand for less cytotoxic antifungal agents for immunocompromised patients, antifungal research has gained significant attention in recent years. Antifungal peptides, and among them, cyclic peptides, are a class of antifungal agents that have been under development since the 1960s. Using cyclic peptides as a promising approach for combating antifungal resistance in pathogenic fungi has gained significant attention in recent years. The identification of antifungal cyclic peptides from various sources has been possible due to the widespread interest in peptide research in recent decades. It is increasingly important to evaluate the narrow to broad-spectrum antifungal activity and the mode of action of synthetic and natural cyclic peptides for both synthesized and extracted peptides. This short review aims to highlight some of the antifungal cyclic peptides isolated from bacteria, fungi, and plants, taking into consideration the progress made in peptide research. Additionally, it provides a summary of synthetic cyclic peptides with antifungal activity and discusses the potential future of utilizing combinations of antifungal peptides from different sources. The review underscores the need for further exploration of the novel therapeutic applications of these abundant and diverse cyclic peptides.

To improve the accuracy of short-term multi-energy load prediction models for integrated energy systems, the historical development law of the multi-energy loads must be considered. Moreover, understanding the complex coupling correlation of the different loads in the multi-energy systems and accounting for other load-influencing factors, such as weather, may further improve the forecasting performance of such models. In this study, a two-stage fuzzy optimization method is proposed for the feature selection and identification of the multi-energy loads. To enrich the information content of the prediction input feature, we introduced a copula correlation feature analysis in the proposed framework, which extracts the complex dynamic coupling correlation of multi-energy loads and applies Akaike information criterion (AIC) to evaluate the adaptability of the different copula models presented. Furthermore, we combined a NARX neural network with Bayesian optimization and an extreme learning machine model optimized using a genetic algorithm to effectively improve the feature fusion performances of the proposed multi-energy load prediction model. The effectiveness of the proposed short-term prediction model was confirmed by the experimental results obtained using the multi-energy load time-series data of an actual integrated energy system.

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

Although the similarity laws were widely used in impact fields, the scaling relations of anisotropic elastic structures often were broken when the geometric distortion (not equal scaling in different spatial directions) and the material distortion (different materials used for scaled model and full-size prototype) were considered. To overcome the difficulty of geometric and material distortion, a directional framework of similarity laws, termed as oriented-density-length-velocity (ODLV) system, is proposed for the anisotropic elastic structure under impact loads. Different from previous similarity law systems using scalar dimensional analysis, the directional similarity law framework mainly considers spatial anisotropy for structural geometry and material parameters. Based on the oriented dimensional analysis and the orthotropic Hooke's law, directional dimensionless numbers and directional scaling relations with geometric power properties for the elastic modulus and the Poisson's ratio are presented systematically. By selecting the dominant material parameters controlling similarity, three important scaling techniques with correction of geometric width and thickness are proposed to compensate for the difficulty of distortion. A clamped square plate with different anisotropic and isotropic elastic materials subjected to dynamic pressure pulse is verified numerically and discussed in detail. The results show that the thin square plate prototype must be scaled to be the thinner/thicker rectangular plate, and the components of displacement, stress and strain between scaled model and full-scale prototype behave good consistency in both spatial and temporal fields.

This paper has experimentally measured volcanic tufa electrical conductance. The calculations are carried out in accordance with the potential of cyclic voltammetry in a constant state. The cyclic voltammograms nanoelectrode platinum prepared electrochemically were examined in the range -0.2 to 1.2 V vs. AgCl [Cl^-]:1.0 M in the presence and absence of volcanic tuff in the aqueous solution of 1.0 M HCl. The cyclic voltammetry studies show that the Nano platinum film suffers degradation when the potential exceeds +0.85 V, and below this potential, it is quite stable. The redox reaction of the electrode is reversible. The nanoparticle platinum synthesized at low temperature and high acid concentration exhibits higher electronic conductivities. It has been observed that, relative to area under the peak aggregate tests, the use of volcanic concrete was showing a large increase in electrical conductivity. It was shown that with cyclic voltammetry, three well-defined anode peak could be achieved at a power of 0.0, 0.4 and 0.6 V versus Ag/AgCl.

Weaving is an ancient and effective structural forming technique characterized by the ability to convert two-dimensional ribbons to three-dimensional structures. However, most 3D structures woven from straight ribbons have topological defects. Baek et al. proposed a method to weave smoother continuous 3D surface structures using naturally curved (in-plane) ribbons, obtained a new surface structure with relatively continuous variation of Gaussian curvature, and analyzed its geometric properties. We believe that this new 3D surface structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated a 3D surface structure using naturally curved (in-plane) ribbon weaving, and the results of calculations and experiments show that such structures have better buckling stability than those woven with straight ribbons. It is observed that the number of ribbons influences the buckling behavior of different types of woven structures.

Based on the two-node Euler-Bernoulli beam, the tower system is discretized by finite element method, and the cubic Hermite polynomial is taken as the shape function of the beam element, and the structural characteristic matrix of the tower system is calculated, and the wind turbine-nacelle-tower multi-degree of freedom is established Finite element numerical model. The aerodynamic load calculation formula for any nacelle attitude angle is deduced. The influence of the vibration feedback of the flexible tower on the aerodynamic load of the wind turbine is studied. The results show that when the rigidity of the tower is large, the impact of tower vibration feedback on the aeroelastic load of the wind turbine is small. For a tower system with greater flexibility, the time-varying feedback of wind-induced vibration will cause greater aeroelastic load changes, especially the overturning moment of the tower top, which will cause a greater impact on the dynamic behavior of the tower in the downwind and crosswind directions. As the flexibility of the tower system increases, the interaction between tower vibration and aerodynamic load is gradually increasing. Taking the impact of the flexible tower on the aeroelastic load of the wind turbine into account, on the one hand, helps to predict the wind more accurately. The aerodynamic load of the wind turbine improves the efficiency of wind energy utilization. On the other hand, it can more accurately analyze the dynamic behavior of the flexible structure of the wind turbine, which is extremely beneficial to the structural optimization design of the wind turbine.

Demand response flexible loads can provide fast regulation and ancillary services as reserve capacity in power systems. This paper proposes a joint optimization dispatch control strategy for source-load system with stochastic renewable power injection and flexible thermostatically controlled loads (TCLs) and plug-in electric vehicles (PEVs). Specifically, the optimization model is characterized by a chance constraint look-ahead programming to maximal the social welfare of both units and load agents. By solving the chance constraint optimization with sample average approximation (SAA) method, the optimal power scheduling for units and TCL/PEV agents can be obtained. Secondly, two demand response control algorithms for TCLs and PEVs are proposed respectively based on the aggregate control models of the load agents. The TCLs are controlled by its temperature setpoints and PEVs are controlled by its charging power such that the DR control objective can be fulfilled. The effectiveness of the proposed dispatch and control algorithm has been demonstrated by the simulation studies on a modified IEEE 39 bus system with a wind farm, a photovoltaic power station, two TCL agents and two PEV agents.

In our previous work, we demonstrated the potential of the amphiphilic cyclic peptide [W4R4] as a promising antimicrobial agent. The extensive data accumulated on the antimicrobial activity of this peptide and its homologs presented an opportunity to unravel the molecular mechanisms governing their action and establish crucial structure-activity relationships (SAR). To achieve this, we employed a comprehensive approach involving peptide synthesis, in vitro biological testing, and molecular modeling to systematically analyze the SAR of a series of cyclic peptides derived from the [W4R4] scaffold. Minimal modifications were introduced to the original peptide by incorporating either one aromatic hydrophobic residue (W) or one polar positively charged residue (R) while maintaining the sequential W/R arrangement. Additionally, we introduced an "intermediate" substitution by incorporating 2,5-diketopiperazine (DKP), possessing both aromatic and polar properties, into the macrocycle [W4R4] between the W and R residues. Notably, this study marked the first synthesis and evaluation of the [W4R4(DKP)] peptide. Structural, dynamic, hydrophobic, and membrane-binding properties of four cyclic peptides ([W4R4], [W5R4], [W4R5], [W4R4(DKP)]) were explored using molecular dynamics simulations within a DOPC/DOPG lipid bilayer that mimics the bacterial membrane. The results obtained revealed distinct SAR profiles for all peptides, enabling the establishment of correlations between their antimicrobial activity and structural/dynamic parameters. These parameters included the degree of conformational plasticity, the depth of immersion into the bi-layer, and the population of the membrane binding mode characterized by the embedding of the hydrophobic peptide pattern into the acyl chain region of lipids. In particular, the peptide [W4R5] exhibited an optimal "activity/binding to the bacterial membrane" pattern. This work highlights the significance of our multidisciplinary approach in efficiently deciphering finely regulated SAR profiles for a series of homologous peptides with diverse activities. Furthermore, this research provides a solid foundation for the rational design of novel antimicrobial peptides.

Ramsey theory influences the dynamics of mechanical systems, which may be described as abstract complete graphs. We address a mechanical system which is completely interconnected with the two kinds of ideal Hookean springs. The suggested system mechanically corresponds to the cyclic molecules, in which functional groups are interconnected with two kinds of chemical bonds, represented mechanically with two springs k1 and k2. In this paper, we consider a Cyclic system (molecule) built of six equal masses m and two kinds of springs. We pose the following question: what is the minimal number of masses in the such a system in which three masses are constrained to be connected with spring k1 or three masses to be connected with spring k2? The answer to this question is supplied by the Ramsey theory, and it is formally stated as follows: what is the minimal number R3,3? The result emerging from the Ramsey theory is R3,3=6. Thus, in the aforementioned interconnected mechanical system will be necessarily present the triangles (at least one triangle), built of masses and springs. This prediction constitutes the vibrational spectrum of the system. Thus, the Ramsey Theory supplies the selection rules for the vibrational spectra of the cyclic molecules. Symmetrical system built of six vibrating entities is addressed. The Ramsey approach works for 2D and 3D molecules, which may be described as abstract complete graphs. The extension of the proposed Ramsey approach to the systems, partially connected by ideal springs, viscoelastic systems and systems, in which elasticity is of an entropy nature is discussed. “Multi-color systems” built of three kinds of ideal springs are addressed. The notion of the inverse Ramsey network is introduced and analyzed.

The effect of the strain rate on damage in carbon black filled EPDM stretched during single and multiple uniaxial loading is investigated. This has been performed by analysing the stress-strain response, the evolution of damage by Digital Image Correlation (DIC), the associated dissipative heat source by InfraRed thermography (IR), and the chains network damage by swelling. The strain rates were selected to cover the transition from quasi-static to medium strain rate conditions. In single loading conditions, the increase of the strain rate yields in a preferential damage of the filler network while rubber network is preserved. Such damage is accompanied by a stress softening and an adiabatic heat source rise. Conversely, increasing the strain rate in cyclic loading conditions yields in a filler network accommodation and a high self-heating whose combined effect is proposed as a possible cause of the ability of filled EPDM to limit damage, by reducing cavities opening during loading and favoring cavities closing upon unloading.

The application of instrumented indentation to assess material properties like Young’s modulus and micro-hardness has become a standard method. In recent developments, indentation experiments and simulations have been combined to inverse methods, from which further material parameters as yield strength, work hardening rate, and tensile strength can be determined. In this work, an inverse method is introduced by which material parameters for cyclic plasticity, i.e. kinematic hardening parameters, can be determined. To accomplish this, cyclic Vickers indentation experiments are combined with finite element simulations of the indentation with unknown material properties, which are then determined by inverse analysis. To validate the proposed method, these parameters are subsequently applied to predict the uniaxial stress-strain response of a material with success. The method has been validated successfully for a quenched and tempered martensitic steel and for technically pure copper, where an excellent agreement between measured and predicted cyclic stress-strain-curves has been achieved. Hence, the proposed inverse method based on cyclic nanoindentation, as a quasi-non-destructive method, could complement or even substitute the resource-intensive conventional fatigue testing in the future for some applications.

Lake Rawa Besar is an urban lake surrounded by dense settlements and market area. Currently Lake Rawa Besar is experiencing physical and ecology strain. This research’s objectives are to determine the levels of sediment and nutrient, the distribution, also the relation to land use and human activities producing pollutant. Field surveys with 30 sample points and observations was needed scattered within the lake. Measuring the value of each parameter is carried out in national standardized laboratory. The result shows that sediment load of TDS is still below the standard limit for clean water, while TSS levels in the middle of lake exceed the standard limit. Nutrient loads, spesifically nitrate and phospate levels is below the standard limit. While turbidity and BOD levels have a uniform distribution pattern in the lake, exceed the standard limit for clean water, and have a positive correlation. High levels of turbidity and BOD are caused by household waste and human activities producing organic waste such as tofu factory, fowl manure, and garbage dump. Small sewage goes into the lake mediates pollutants inflow. Attention is needed by nearby people, also for the government, to sustain the ecological condition of the lake.

The impact of cyclic heat stress (CHS) and lighting events on pig feeding behavior (FB) was investigated. The FB of 90 gilts was recorded in real time under two ambient temperatures (AT): thermoneutrality (TN, 22 °C) or CHS (22°/35 °C). The day was divided into four periods: PI (06-08 h); PII (08-18 h); PIII (18-20 h); and PIV (20-06 h). Automatic and Intelligent Precision Feeders recorded each feed event for each pig. An estimated meal criterion (49 minutes) was used to calculate the FB variables. Feed behavior in both ATs followed a circadian pattern. The CHS reduced the feed intake by 6.9%. Pigs prioritized feed intake during the coolest hours of the day; however, nocturnal cooling did not allow the pigs to compensate for the reduced meal size due to CHS. The highest meal size and most of the meals were observed during the lighting-on period. Pigs reduced their interval between meals during periods II and III. The lighting program increased the meal size when the lights were switched on and reduced the meal size when the lights were switched off. Thus, the dynamics of the FB were largely influenced by AT, while the meal size was affected by the lighting program.

Microbial growth has been of prime importance to the researchers in health and biotechnology industries. It has been known to be closely associated to the secretion of extracellular polymeric substances that help in the formation of colonies. Inter-microbial communication happens within such colonies by means of extracellular electron transfer mediated by the aforementioned polymeric substances. Conventionally, different phases of microbial growth are monitored with the aid of a traditional UV-Visible spectrophotometer by measuring the optical density of the liquid medium at 280 nm. In this paper, we have developed an alternative novel way to sense different growth phases employing electrochemical means i.e. two-terminal cyclic voltammetry. This cyclic voltammetry relies on the extracellular electron transfer mechanism taking place via the polymeric substances secreted by the microorganisms, measured by the temporal area changes in the current-voltage hysteresis curves in the inoculated nutrient broth. This work paves a new way to detect the biological activity in the medium, which can be directly correlated to the population of microorganisms. It would be of immense interest to scientists and researchers working in the field of microbiology as well as in development of biosensors, electrochemical sensors etc. which would be helpful in absence of traditional spectrophotometers.

The purpose of the present study was to develop an experimental model for studying of the intra-articular knee movements depending on the work of the knee joint and applied muscle groups in isometric stretching conditions with different tens. The experimental procedure includes ultrasound examination of a knee joint after isometric stretching of healthy men (n=32). The changes in millimeters of the distances between the femur and tibia were measured with ultrasound sonographer at three stages. The first stage was performed on ten (n=10) healthy men at five different sitting and upright positions. In the second and third experimental model stages the lower limbs loading was on 22 participants. Our hypothesis which was confirmed, was that as a result of increasing extraloads on the participants back (2, 5, 10, 15, 17, 20 kg), a intra-articular decrease in the femur-tibia cartilage surface distance wiil be observed. The accuracy of the created experimental model was improved over its three stages from 30% to 9%. Quantitative model data can help to create a mathematical model for the mechanical effects during deformation of the knee joint bone cartilage, as well as to outlines the some future tasks: increasing loading weights; enlarge participant groups; comparison men and women; healthy and pathology comparison.

The article concerns problems related to the assessment of reactive power in power networks with non-linear, fast-varying loads, such as electric arc furnaces, rolling mill drives, etc. The operation of this type of loads is characterized by the introduction of interharmonic currents (including higher harmonics) into the power supply network and a relatively low power factor. Rapid changes in the RMS value of the current also cause voltage fluctuations and the related phenomenon - flicker. Therefore, there is a need to evaluate the selection of power of compensating devices taking into account the random nature of load changes and the distortion of current and voltage waveforms, in particular interharmonic components, the impact of which has not been fully investigated so far. To analyze the random nature of load changes, autocorrelation functions were used, which allowed for the estimation of the expected values of the arc furnace current distortion coefficient (based on the recorded waveforms). In order to determine the parameters of reactive power compensating devices, and in particular capacitor banks, an autocorrelation function in the exponential-cosine-sine form was used, which meets the conditions of differentiation. The article contains comparative results of calculations of the reactive power of capacitor banks determined using different methods.

This paper presents results from numerical simulations validated by experimental results related to the effects of DSSI on the dynamic response of bridges. An in-service overpass was shaken using the T-Rex, a large-amplitude mobile shaker from the National Hazards Engineering Research Infrastructure (NHERI) facilities. Studies implementing Finite Element Modeling to develop time histories, response spectra, and eigenmodes were conducted in a forward-modeling problem setup. Two models were created to assess the DSSI effects on the dynamic response of the bridge. One model included elements that incorporate DSSI effects, while the other had fixed-base boundary conditions. The response from the DSSI FEM model matched the field results better than the fixed-base model, in terms of the peak response amplitudes and identified natural frequencies and modes. The influence of a series of factors, such as the soil shear wave velocity, bridge height, bridge foundation embedment depth and the corresponding rigidity, slenderness, and embedment ratios, on the bridge response is presented.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

To implement renewable energy resources, microgrid systems have been adopted and developed into the technology of choice to assure mass electrification in the next decade. Microgrid systems have a number of advantages over the conventional utility grid systems, however, it faces severe instability issues due to continually increasing constant power loads. To improve the stability of the entire system, load side compensation technique is chosen because of its robustness and cost effectiveness. In this particular occasion, a sliding mode controller is developed for microgrid system in the presence of CPL to assure certain control objective of keeping the output voltage constant at 480V. After that, the robustness analysis of the sliding mode controller against parametric uncertainties is presented. The sliding mode controller robustness against parametric uncertainties, frequency variations, and additive white Gaussian noise (AWGN) are illustrated in this paper. Later, the performance of the PID and sliding Mode controller is compared in case of nonlinearity, parameter uncertainties, and noise rejection to justify the selection of Sliding Mode controller over PID controller. All the necessary calculations are reckoned mathematically and results are verified in the virtual platform such as MATLAB/Simulink with the appreciable outcome.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

This study investigates the cyclic load application impact on fly ash-based geopolymer composites that are reinforced with a low amount of fibre reinforcement. For reinforcement purposes, PVA and steel fibres are used. For testing purposes, four geopolymer composite mixes were made, 3 of which had fibre reinforcement. Simultaneously specimens were tested for shrinkage, static load-induced creep, and cyclic load-induced creep. For static and cyclic creep testing, specimens were loaded with 20% of their strength. For cyclic creep testing, load application and release cycles were seven days long. When each cycle was introduced, the load was added in steps. In 5 minutes, by 25% steps of the necessary load, the specimens were loaded or unloaded. Only plain specimens show that static creep strains are within cyclic creep strains. For all the other specimens, the static load is higher than the cyclic load-induced creep amplitude. Also, 1% PVA fibre-reinforced specimens show the most elastic characteristics under cyclic load, and 1% steel fibre-reinforced specimens appear to be the most resistant to the cyclic load introduction.

The dynamic evolution and variation of electrical loads is now a priority for optimum management and, above all, forecasting. Indeed, these dynamic load variations require computer tools able to implement optimal load forecasting models. Scientific research into automated models for forecasting electrical loads therefore represents a challenge for scientific researchers. Several research studies have therefore been carried out. These include machine learning approaches such as: LSTM (Long Short-Term Memory), Support Vector Machine (SVM) and others. This article proposes a comparison study between a hybrid model based on the wavelet transform coupled with the adaboost method, and LSTM, for forecasting electricity consumption loads. Python 3.10 was used for the studies. The first results obtained consisted in the study of electricity load forecasts over four (04) data sets of the year (January, April, August and December). These results are very satisfactory, showing a good correlation between the real results of the electrical load consumption data, and the results of the implemented model. The electrical load consumption data are collected from a renewable energy production source: photovoltaic solar energy. The model test results (R2) obtained range from 0.919 to 0.958. These results are representative of real data and reflect the model's performance. The second set of results concerns a comparative study between the methods used by Y. Xie et al (CNN, MLP, LSTM-AM and LSTM-AM-MLP), and our approach. The prediction results obtained between the approaches show a prediction gap ranging from 0.15 to 0.78 for RMSE and 0.83 for MAPE. These results show significant differences between the methods. The minimization of errors by our model, therefore, reflects the model's performance in terms of accuracy, which is necessary for the optimal management of consumer electricity load forecasts in order to ensure balance between supply and demand.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

There are many welded structures in the world such as bridges and viaducts that are subject to fatigue. These structures, generally made of non-alloy or low-alloy steels, have been put into operation some of them with many years ago and have accumulated a large number of variable load cycles over the time. For this reason the occurrence of fatigue phenomenon is inevitable and consists in the occurrence of failures at stresses applied to the structure, below the yield limit of the material. These stresses under the static loads would not cause the failures to appear..This paper will investigate whether two reconditioning techniques “weld toe grinding” and “WIG remelting weld toe”, influences favorably the behavior of welded structures made from HSLA steel, in static and variable loads and therefore if the application of these techniques is justified in both cases. In the paper will be presented the chemical composition and mechanical properties of the base and filler materials, micro and macrostructures, graphics with the variation of microhardness, static and fatigue tensile tests will be performed, and it will be rised durability curve in case of fatigue tests.

Background: Cytokines and chemokines are critical regulators of innate and adaptive immunities during viral infection. We examined innate and adaptive immune responses to hepatitis C virus (HCV) and hepatitis B virus (HBV) at baseline and against controls. Methods: Twenty-seven cytokines were evaluated before treatment in 27 patients with chronic hepatitis C(CHC) [genotype1 (n=20), genotype2 (n=7), HCVRNA 5.72IU/ml] and 12 chronic hepatitis B(CHB) [e-antigen (Ag) (+) (n=5), e-Ag (-) (n=7), HBVDNA 6.191.31Logcopies/ml] and against controls(n=5). Results: Th1 and Th2 cytokines were significantly higher (p<0.05) in CHB than in CHC. The levels of IL-IL10 in CHC and CHB, and IL15 in CHC(genotype2) and CHB were significantly lower (p<0.05) than in controls. The levels of CXCL8 in CHC and CHB, IL12 in CHC and CHB [e-Ag (-)] and CXCL10 in CHC and CHB were significantly higher (p<0.05) than in controls. IFN-γwas higher in CHB than in controls. Conclusion: Cytokines levels differed between CHB and CHC before treatment. Innate immune responses were impaired in CHB with HBeAg(-) and CHC, but not in CHB with HBeAg(+) with high viral loads. Adaptive immune responses were impaired in CHB and CHC and appear to reflect the distinct state of virus-host immune interactions between CHB and CHC.

Traditional gene set enrichment analysis falters when applied to large genomic domains, where neighboring genes often share functions. This spatial dependency creates misleading enrichments, mistaking mere physical proximity for genuine biological connections. Here we present Spatial Adjusted Gene Ontology (SAGO), a novel cyclic permutation-based approach, to tackle this challenge. SAGO separates enrichments due to spatial proximity from genuine biological links by incorporating the genes' spatial arrangement into the analysis. We applied SAGO to various datasets in which the identified genomic intervals are large, including replication timing domains, H3K9me3 and H3K27me3 large domains, HiC compartments and lamina associated domains (LADs). Intriguingly, applying SAGO to prostate cancer samples with large copy number alteration (CNAs) domains eliminated most of the enriched GO terms, thus helping to accurately identify biologically relevant gene sets linked to oncogenic processes, free from spatial bias.

Cyclic olefin copolymer (COC) is a novel type of thermoplastic polymer gaining the attention of the scientific community in electronic, optoelectronic, biomedicine and packaging applications. Despite the benefits in the use of COC like undoubted optical transparency, chemical stability, good water-vapor barrier and biocompatibility, its original hydrophobicity restricts its wider applicability and optimization of its performances. Presently, we report on the optical, and morphological properties of the films of COC covered with Ti in selected areas. The layer of Ti on COC was deposited by pulsed lased deposition processing. The Ti/COC film was characterized by UV-Vis spectroscopy indicating that its transmittance in the visible region decreased by about 20% with respect to the pristine polymer. The quality of the deposited Ti was assessed with the morphology by scanning electron (SEM) and atomic force microscopies (AFM). The modification of the wettability was observed by the sessile drop method indicating a reduction of the native hydrophilicity.

Ferrocene and its derivatives have ecologically effective antidetane properties. In this regard, ferrocene reacts with cyclic ketones and ferrosenylcarbinols are synthesized. It should be noted that ferrocene enters into electrophilic reactions and the process takes place in an acidic environment. In addition, the yield of the new product was small compared to the reactions of ferrocene with non-cyclic ketones. This is due to the spatial structures of molecules. The elemental analysis of obtained compounds was carried out; the structures were researched by cyclic voltammograms and Chronoamperometric.

In this investigation, polymethyl methacrylate (PMMA) was mixed with cyclic olefin copolymer (COC) because of its hardness, strength, and transparency properties. The results of thermal analysis through TGA and DTG showed that the thermal properties of the alloy are improved using 40% cyclic olefin copolymer. Kinetics of thermal degradation (pyrolysis) of polymers have been studied and analyzed and thermal pyrolysis of polymethyl methacrylate and cyclic olefin copolymer thermoplastic polymer was conducted. The computation of kinetic analysis is measured along with the different methods used to study the kinetics. The activation energy (E) of degradation of studied materials was estimated using Ozawa Flynn and Wall (OFW), Starink and Kissinger’s methods, and evaluation of three kinetic parameters taken appropriate kinetic model in terms of percent change for both types of polymers have been proposed, and finally, simulated curves were compared with the experimental curves. Both mechanisms of degradation for COC and PMMA under nitrogen atmosphere will reflect intramolecular transfer and random scission of the main chain.

Exogenous RNA comprises the genetic material associated with several diseases which require immediate treatment, and thus mechanisms to hinder intracellular translation and reproduction of RNA viral agents are of great importance. Applying recent developments from this lab in methods relating to the interaction of DNA with steroid hormones, cyclic compounds are presented for intermolecular binding to nucleic acids. The requirements to achieve binding with RNA nucleotide pairs are described, which involve at a minimum functional elements positioned to interact with the lateral phosphate groups for each of the RNA strands through coupling with a positively charged ion, such as Mg2+, Ca2+, or Zn2+ ions; and an intermolecular hydrogen bond with the oxygen element of uracil at the carbon two location. Additional features of the binding molecules are examined for enhancements and differentiation in binding capability and include aromatic groups that have both a structural role of steric hindrance and a functional role to stabilize the binding mechanisms. Several categories of cyclic compounds are associated to have specific binding capabilities, and the interaction of these structures with potential receptor molecules are evaluated for assessment in delivery and binding of the compound to nucleic acids.

Nonlinear loads, a crucial component of power systems grids, pose a challenge due to harmonics injection. Our research tackles this issue with a novel approach - a modified green plug / switched filter compensation scheme using fuzzy logic controllers. This innovative scheme, presented in the paper, utilizes dual action pulse width modulation to ensure switching functions from harmonic reduction and capacitive compensation for inrush nonlinear type AC loads.  The scheme's multi-loop regulations and online switching effectively handle dynamic type slow acting inrush, motorized and other rectifier type-nonlinear loads, enhancing power factor, power quality at source and load buses, and reducing total harmonic distortion at key source and sensitive nonlinear load buses. A simulation model in the MATLAB/SIMULINK software environment demonstrates the efficiency of the proposed FACTS technique. The results show that voltage, current, active power, reactive power, power factor regulation, and effective energy utilization are achievable with the designed FACTS-MFCC-SFC. The switched modulated AC green plug filter significantly improves power quality and enhances power factor in the case of inrush and nonlinear loads.

The influence of applied loads on free vibrations analysis of plates and shells panels made of functionally graded materials is analyzed in the present work. Formulations for the static analysis considering geometrically nonlinear behavior, as well as linear buckling and free vibrations analyses are considered. The calculation of the through-thickness stress distribution is also performed. A finite element model based on a higher order shear deformation theory and using a non-conforming triangular flat plate/shell element with 3 nodes, and 8 degrees of freedom per node is used in the numerical implementation. The results obtained with this numerical model are presented, discussed, and compared with alternative solutions published by other authors in some benchmark applications.

Expanded polystyrene (EPS)- block geofoam is an extremely lightweight fill material utilized in many geotechnical applications such as roadway and railway embankments. This study provides a methodology for analyzing the load-bearing capacity and horizontal sliding failure mechanisms for seismic internal stability analysis of EPSblock geofoam embankments. The seismic analysis procedure is demonstrated by analysis of one of the EPS-block geofoam embankments that Tennessee Department of Transportation is proposing a partial replacement of an existing bridge in Memphis, Tennessee in the USA. The objective of the seismic analysis procedure is to determine stresses from anticipated earthquakes to select the proper type of EPS considering both the 1% and 2% strain criteria that can support the anticipated increase in stress and potential horizontal displacements due to dynamic and static stresses. The study revealed that the 2% criterion provides an economical advantage compared to the 1% criterion.

Frosty pod rot, caused by Moniliophthora roreri, is the most damaging disease of cacao in Latin America. However, to better comprehend its epidemiology, we must understand its dissemination and proliferation. Still, we ignore how loads of M. roreri spores fluctuate across growing seasons since we lack a reliable technique to quantify M. roreri spores in the fields. Therefore, we developed a method that uses a spore trap to capture M. roreri spores and qPCR to quantify them. This study demonstrated that this technique could quantify 3.9 x104 M. roreri spores with a 95 % confidence level. However, it could not differentiate between M. roreri and its close relative, M. perniciosa. Despite this limitation, we could detect and quantify Moniliophthora spores from environmental samples taken from a cacao field. This technique can help the phytopathologist address studies more accurately in disseminating cacao pathogens.

The aim of the study is to assess the loads that are transferred from the main rotor and the tail rotor to the helicopter fuselage. These loads change in the various phases of the transient flight as a result of the variable control of the maneuver and as a result of the variable flow around the blades. The knowledge of the loads allows for the proper selection of the level of excitations that should load the fuselage structure during fatigue and strength tests. The simulation model describing the helicopter flight is discussed. This model takes into account the motion of each blade relative to its hinges. Results are shown for two maneuvers - pullup/pushover and diving. The values of extreme loads transferred to the fuselage were obtained.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

The earth pressure acting on soilbag reinforced retaining structures subjected to surcharge loads under non-limited states, is crucial for designing these structures. In this study, the earth pressures are investigated through model tests of the soilbag reinforced retaining wall. Findings from these tests reveal a non-linear distribution of lateral earth pressure on the wall when subjected to surcharge loads in non-limited states, with an observed escalation in pressure corresponding to increased surcharge loads. Compression tests on soilbags were conducted to analyze their lateral stress-strain behavior. Insights from these tests facilitated the development of a predictive method for estimating lateral pressure on soilbag reinforced retaining walls under similar conditions. This method, rooted in the principle of force equilibrium in differential elements, has its accuracy and reliability substantiated by the alignment of its predictions with the model test outcomes.

A three-phase multilevel inverter (MLI) synthesized with 31-levels in the output voltage is used to provide ac supply to a three-phase, squirrel-cage induction motor. The gating angles required for thirty power switches in MLI are optimized by both Genetic Algorithm (GA) and Gray Wolf Op-timization (GWO). In the optimization technique, the optimal angles are determined by solving the trigonometric equations from the Fourier analysis for targeting minimum total harmonic distortion (THD) at the MLI output. Simulation model and experimental prototype are developed for performance analysis and validation. The results obtained demonstrate that the MLI is effec-tively able to produce 31-levels of three-phase ac output voltages with THD not exceeding 5% when loaded with a resistive load and a three-phase induction motor. The voltages and currents are measured and recorded for different loads and operating conditions, including the amount of energy consumed by the loads, as well as frequency analysis, which shows the absence of most of the triple harmonics that have a negative impact on the efficiency of the inverter.

Powder metallurgy is a preferred manufacturing method in various industries because it offers design flexibility, material efficiency and a cost-effective production. In this work, we study the effects of different compaction directions on the strength of parts produced by powder metallurgy. Al–4wt.%Cu alloys are used due to their recyclability, and three distinctive compaction pressures are applied, resulting in two sample groups. One group is air-cooled after sintering, while the other is water-quenched and naturally aged (T4 temper). Both the compressive and tensile strengths are measured and analyzed. The study reveals that both heat treatments and compaction directions significantly influence anisotropic strengths. The novelty of this research lies in the use of powders that can be reused from machining, turning, or foundry rejection. By omitting or reducing the melting stage and employing simple powder metallurgy, the cost-effective and environmentally friendly processes are achieved. The planning of compaction load, compaction direction, and heat treatments is found to play a crucial role in determining the final mechanical performance. Notably, this approach aligns with the environmental, social and governance (ESG) practices that have been increasingly adopted by industry.

In the context of the Korean building structure standard KDS2022, wind loads can be readily calculated in terms of the along-wind, across-wind, and torsional components, based on a single wind direction. However, this approach falls short in accurately and safely evaluating the impact of winds from various directions. Therefore, in this study, we developed a Wind Load Calculation Program (WCP) capable of predicting wind loads with relative precision during the preliminary design phase. First, wind tunnel tests were conducted to identify the essential factors necessary for calculating wind loads and the variables influencing these factors. The building shape considered was a square, and the wind force coefficients and power spectral density were measured by combining 4 ground roughness values, 11 side ratios (), 4 aspect ratios (), and wind directions ranging from 0° to 90°. Subsequently, a generalized formulation was devised to facilitate wind load calculations across diverse conditions and a method for calculating load combination coefficients, considering response correlation and load simultaneity, was presented. Finally, the wind loads obtained from the wind tunnel tests were compared with those predicted by the WCP using an actual project model.

Due to the non-contact measurement characteristics of trackside acoustic technology, it is now utilized for train bearing fault diagnosis. However, the relative motion between the train and the trackside acoustic detection device introduces Doppler aberration in the collected acoustic signal, which affects bearing fault diagnosis. Moreover, when a fault occurs in the train bearing, its acoustic signal exhibits cyclic smoothness characteristics that can be effectively analyzed using the cyclic smoothness method for more accurate judgment. In order to minimize diagnostic errors and enhance accuracy in bearing fault diagnosis, this study integrates bearing fault characteristics with Doppler aberration correction methods and cyclic smoothness techniques for current-stage bearings diagnostics. The overall time-domain graph becomes more compact with an approximately 50% increase in amplitude after correction compared to pre-correction values; other parameters experience enhancements ranging from 20-60%. These results validate the feasibility of our proposed approach and establish a framework for conducting bearing fault diagnosis based on cyclically smoothed Doppler aberration correction.

Bismuth oxides are well-known electro-catalysts in fuel cells systems; they are usually used as anodic materials for the oxidation of low molecular weight alcohols. The utilization of BiO₂ and MnO₂ as catalysts in the pharmaceutical analysis is analytical method for the determination of heavy metal antibacterial agents in Pharmaceutical Dosage form is developed. The method is based on the voltammetric determination of heavy metal using Bidified platinum electrode by Bismuth oxide. The two components are oxidized at the Bidified electrode surface with the development of current that is linearly proportional to their concentrations in the range of 7.04*10^-7- 1*10^-3 M heavy metal. The oxidation reaction of the two components is pH-dependent, in which the buffer used is Britton-Robinson at pH = 7.00 where maximum peak current and maximum peak separation is obtained. The regression factors obtained from the calibration curves are 0.9812. The method of analysis was validated, where the limit of detection (LOD) and the limit of quantitation (LOQ) were calculated to be 1.44*10^-4 M, 4.36*10^-4 M and 1.27*10^-4 M, 3.84*10^-4 M respectively, the percentage recovery of both components was also calculated to 77 % for heavy metal.

Epigenetic reprogramming using cyclic expression of Yamanaka factors has been demonstrated to rejuvenate on a systemic level in animal models with no obvious deleterious effects. Here we discuss a strategy for cyclic and systemic expression of Yamanaka factors in wild-type animals amenable for adaptation as a human therapy. This is based on the use of the little- known Amsacta moorei Entomopoxvirus vector in combination with microbubble mediated focused ultrasound-driven blood vessel permeabilization to facilitate the system-wide distribution of the virus.

This research investigates the effects of torsional moments on the mechanical behavior of thin-walled open-ended vertical pile foundations subjected to lateral wind loads. The warping and torsion effect generated over the piles due to the resultant lateral load impact outside the shear center is analyzed in-field tests. Complementarily, a two-dimensional finite element model based on the simple bending stress-strain state as well as a three-dimensional finite element model considering torsional effects were implemented and their results analyzed. Finally, a comparative analysis between the in-field lateral loading tests and the finite element model approaches was established and correlations between the errors and the parameters of influence were highlighted. From the results, it has been ascertained that the slender thin-walled open-ended pile foundations are particularly sensitive to small load deviations from their center of gravity, this leads to the fact that the slenderer and the more eccentricity of the load, the more it affects the torsion and warping of the pile. Calculation methodologies usually consider a simple in-plane bending behavior which conducts to errors between 44 and 58% of the experimental results.

In this study, robust composite solid electrolytes were developed and employed them to enhance the performance of Li-metal batteries significantly. The robust composite solid electrolytes are composed of a soft polymer, poly(ethylene oxide), a Li salt, bis(trifluoromethanesulfonyl)imide (LiTFSI), and super ionic conductive ceramic fillers such as Li1.5Al0.5Ti1.5(PO4)3 (LATP), and Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The main goal of this study is to enhance the electrochemical stability and ionic conductivity. The ionic conductivities of the composite solid electrolytes were found to be 2.08 × 10-4 and 1.64 × 10-4 S cm-1 with the introduction of LATP and LLZTO fillers, respectively. The results prove that the fabricated solid electrolyte was electrochemical stable at voltage exceeding 4.25 V vs. Li/Li+. The internal resistance of the solid electrolyte significantly reduced as compare to gel electrolyte. This reduction can be attributed owing to the alleviation of bulk electrolyte, charge-transfer, and interfacial electrolyte/electrode impedance. When LiFePO4 cathode sheets are coated with a composite solid electrolyte containing LATP powders, the resulting Li-metal battery displays high capacity at 5 C (with a capacity retention of 65.2% compared to the original capacity at 0.2 C) as well as superior cyclic stability and excellent Coulombic efficiency (&gt; 99.5%, over 200 cycles). These results confirm that the composite solid electrolyte acts as a protective layer which have ability to prevent the growth of Li dendrites. Consequently, the fabricated electrolyte configuration can be engineered to enable high energy/power density and electrochemical stable cyclability in Li-metal batteries.

The synergistic effect of silicon and cerium addition on the oxidation resistance of pack cementation aluminide coating applied on Ni-based superalloy substrate was investigated. The effect of cerium and silicon on the scale morphology, oxidation behavior, and scale spallation tendency are discussed based on the experimental results, using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analyses (EDX). In addition, the oxidation resistance was evaluated by measuring the weight of samples after each 16-hour cycle at 1100˚C for 50 cycles. The experiments indicated that silicon addition to aluminide coating improves the oxidation resistance through the formation of β-NiAl1-nSin and δ-Ni2Al3-nSin and δ-Ni2Si phases. Furthermore, the addition of 1% cerium to modified aluminide enhances the formation of the fine-grained microstructure of the β-NiAl and δ-Ni2Al3 and reduces the outward/inward diffusion of elements (so-called blocking effect) which significantly modifies the hot oxidation resistance. The addition of 2% cerium, owing to the distortion of the β-NiAl and δ-Ni2Al3 phases, strictly decreases the hot oxidation resistance and the coating is exfoliated after 450 h at 1100 °C. The cyclic oxidation tests showed that the samples containing 1% cerium and 6% silicon possess the highest hot oxidation resistance in which 2 mg/cm2 weight loss of Ce-Si-aluminide was reported after 800 h. This is attributed to the simultaneous effect of cerium and silicon during the deposition process which reduces the oxygen diffusion and reduces the growth rate of α-Al2O3 during oxidation tests. The α-Al2O3 oxidation layer morphology showed that finer grains are formed in samples containing optimum ratios of cerium and silicon which indicates that these elements improve the coating adhesion and oxidation resistance simultaneously.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

The pharmaceutical market consists mainly of chemical and biological drugs. These drugs act on different types of targets and have distinct pharmacological properties. Generally, chemical drugs bind to the active site of target enzymes and easily penetrate the cell membrane owing to their small size; however, biological drugs can bind to the protein–protein interaction site but are less stable due to their protein properties. Cyclic peptides possess the pharmacological merits of both chemical and biological drugs, such as the ability to bind to the protein–protein interaction site and penetrate cell membranes. In this study, we developed a simple two-step system to generate a cyclic peptide library using the split intein of Npu DnaE and Gateway cloning. The first step is the PCR of Ready-to-use(R) template DNA having the coding sequences of random cyclic peptides between two split intein elements NpuC and NpuN and the recombination recognition site of Gateway cloning. The second step is the transformation of the PCR products via Gateway cloning to produce colonies with expression vectors to produce cyclic peptides comprising random amino acid sequences. The expression vectors in randomly chosen transformed colonies were confirmed to have random cyclic peptide sequences and all the clones, except ones having a stop codon in the cyclic peptide coding region, showed the expected protein splicing result. This simple two-step system for bacterial expression systems may be modified to suit various expression systems for cell-based assays.

As an important follow-up report on the latest study of the first author (H.S.) on an off-shell quantum field causing a dressed photon and dark energy, we further discuss a couple of intriguing subjects based on our new theory. One is the dressed photon constant. If we use it, in addition to h¯ and c, as the third component of natural units, then it is defined as the geometric mean of the smallest and the largest lengths: Planck length and that relating to the cosmological constant. Interestingly, this length (≈ 50 nanometers) seems to give a rough measure of the Heisenberg cut for electromagnetic phenomena. The other is a new perspective on cosmology that combines two original notions, i.e., twin universes and conformal cyclic cosmology, proposed respectively by Petit and Penrose, into one novel picture where universes expand self-similarly. We show the possibility that twin universes having a dual structure of [matter with (dark energy &amp; matter)] vs. corresponding anti-entities, separated by an event horizon embedded in the geometric structure of de Sitter space, undergo endless cyclic processes of birth and death, as in the case of the pair creation and annihilation of elementary particles through the intervention of a conformal light field.

The excited-state lifetimes of the anticoagulant drug warfarin (W) in water and in the absence and presence of methyl-β-cyclodextrins (Me-β-CD) were recorded using time-resolved fluorescence measurements. Selective excitation of the open and cyclic protonated isomers of W were acquired with laser emitting diodes (LED) producing 320 and 280 nm excitation pulses, respectively. Formation of the inclusion complex was checked by UV–visible absorption spectroscopy, and the values of binding constants (2.9 × 10³ M^–1 and 4.2 × 10² M^–1 for protonated and deprotonated forms, respectively) were extracted from the spectrophotometric data. Both absorption and time-resolved fluorescence results established that the interior of the macromolecular host binds preferentially the open protonated form, red shifts the maximum of its absorption of light at ~305 nm, extends its excited-state lifetime, and decreases its emission quantum yield (ФF). Collectively, sequestration of the open guest molecules decreases markedly their radiative rate constants (kr), likely due to formation of hydrogen-bonded complexes in both the ground and excited states. Due to lack of interactions, no change was observed in the excited-state lifetime of the cyclic form in the presence of Me-β-CD. The host also increases the excited-state lifetime and ФF of the drug deprotonated form (W¯). These later findings could be attributed to the increased rigidity inside the cavity of Me-β-CD. The pKa values extracted from the variations of the UV–visible absorption spectra of W versus the pH of aqueous solution showed that the open isomer is more acidic in both ground and excited states. The positive shifts in pKa values induced by three derivatives of cyclodextrins: HE-β-CD, Ac-β-CD, and Me-β-CD supported the preferential binding of these hosts to open isomers over cyclic.

The article describes the use of microwave irradiation in the synthesis of bis(cyclo carbonate) compounds (BCC) in bulk (without solvent) from carbon dioxide capture using an epoxidized compound - a commercial epoxy resin, and compares this process to the conventional method. CO2 cycloaddition to epoxides is an ecological and efficient method for the formation of bis(cyclic carbonates). Moreover, the introduction of gas into the reaction mixture was carried out at atmospheric pressure with a controlled flow rate, which is advantageous from an economic point of view. Progressive structural changes and the presence of characteristic chemical groups were monitored using attenuated total reflectance infrared spectroscopy with Fourier transform. The obtained crude products were purified to obtain three fractions, which were subjected to detailed structural analysis using FT-IR and 13CNMR. The formation of the main product with two cyclic carbonates was confirmed. The presence of monomers, dimers and trimers in individual fractions as well as their thermal stability were determined, and the molecular masses in individual fractions were determined using gel permeation chromatography (GPC).

To satisfy the interests of multiple agents and those of comprehensive indicators such as peak-to-valley differences and load fluctuations occurring on the network side, this paper presents a flexible load demand-side response optimization method that considers the benefits of peak-to-valley smoothing. First, load aggregation modelling of air conditioning and electric vehicles was conducted, and the complementarity of the power consumption behaviour of different types of flexible loads was used to improve the responsiveness of the load aggregator. Second, considering demand-side responses and taking into account the interests of both supply and demand, the load fluctuation and peak-to-valley difference on the network side are reduced, and a flexible load double-layer optimization model incorporating the peak-to-valley smoothing benefit is established. Finally, the effectiveness of the proposed optimization model is verified by using the KKT condition and the big M method to evaluate this two-layer optimization problem as a single-layer optimization problem. Comparative examples demonstrate that the proposed two-layer optimization method can improve the revenue of the distribution network operators and the load aggregators by using the complementary nature of the load response characteristics of electric vehicles and air conditioners. Moreover, the proposed method can effectively reduce the load peak-to-valley difference and load fluctuation of the distribution network by introducing the peak-to-valley smoothing benefit model.

With simple but rigorous arguments we prove that the ordinary second quantization of bosonic and fermionc fields is formally equivalent to constraining the elementary degrees of freedom of the classical fields to have intrinsically periodic dynamics in time. This result confirms and extends the formal equivalence obtained in previous papers for general Hamiltonian systems in terms of canonical quantization, for elementary relativistic particles also in terms of the Feynman Path Integrals, as well as other remarkable correspondences of both phenomenological and theoretical fundamental interest.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

This paper presents a detailed description of three methodologies to electrify the rural households of small loads with reliable and economical method using solar energy as input source of power. It is observed that high DC voltage is better and economical solution rather than AC based solar systems and low voltage DC systems. In this paper, three methodologies were analysed to select the right combination of portable converters with low prices, which may further enhance the energy access and affordability to common people. The proposed three methodologies were tested through action research in collaboration with a team of scientists and technical experts of National Institute of Solar Energy. The comparative analysis is carried out on three different converters, various kind of house loads and types of power supply i.e. AC/DC. The performance, quality and economic evaluation has been carried out with the help of MATLAB SIMULINK and other measuring instruments specific for solar photovoltaic systems. The derived results were analysed and inferences made for use in village household loads and their income groups. Further, a three-step analytical framework on village-level power energy efficient power at affordable power preposition was presented. This study will help in the designing as well as in the performance and economic evaluation of converters based on solar photovoltaic systems of different technologies.

Polymer-based composites represent a separate class of materials in demand by the industry. In comparison with other polymers, UHMWPE is characterized by exceptionally high wear and impact resistance. In this work, compacts were produced from UHMWPE GUR 4120 powder with the addition of Nanoscale Detonation Carbon (NDC) and Single-Walled Carbon Nanotubes (SWCNTs) on a hydro-pneumatic impact device by the Cyclic Impact Compaction (CIC) technique. The obtained samples were subjected to wear resistance test, their hardness and tensile strength were measured. Studies have shown that the addition of NDС and SWCNTs in UHMWPE leads to an increase in hardness by 6.4 and 19.6%, to a decrease in wear by 11.5 and 38.5% and a decrease in the coefficient of friction by 10 and 20%, respectively. However, the tensile strength of UHMWPE decreases by 11.7 and 40.4% and elongation decreases by 11.9 and 30.1% with the addition of NDС and SWCNTs, respectively.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.