Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Historically, the military and non-religious, sub-continent’s intellectual elite Muslim men crafted state ideologies before partition, by actively contributing to sociocultural constructs prevalent to this day, in service of colonial patriarchal concepts. The purpose of this ideological collaboration has been to mould a Pakistani cis-gendered female child primarily into the ideal “Pakistan-Muslim” bride for marriage, carried out through her family and society. This has shaped the lives of cis-gendered female children in Pakistan through coerced, gendered control, implemented as prescriptive societal norms. These norms are rooted in colonial, patriarchal ideologies and are functions of capital and coercion intentionally perpetuated to erase her pluralistic identity, reducing her to a central resource within a family unit. To the military concept of nationalism, her mind and her body symbolize the unification and centralization of a statist ideology. Thus, the military state plays an essential role in shaping her purpose around the concept of nationalism. The intellectual elite, via the state, uphold colonial, patriarchal ideologies, where the primary identity of a cis-gendered female child is actualized through her marriage. The cis-gendered female child’s life is a vehicle to unify the state’s two-fold “Pakistani-Muslim” agenda, by implementing a ‘singular statist narrative’. A narrative that attempts to resolve two major tensions: First, it seeks to wipe out the possibility of a nation connecting with and exploring its own immense, internal ethnocultural diversity. It does this by imposing an imagined “homogenous Muslim” identity — which doesn’t exist — and is instead imported from multiple countries to reinforce a ‘singular statist narrative’, Second, it aims to control the mixing of local, sociocultural narratives by bridging any disjuncture between them by labelling colonial institutional patriarchy concepts as inherently “Pakistani”; in service of its preferred ‘singular statist narrative’.

Distributed Energy Resources might have a severe influence on Power Line Communications, as they can generate interfering signals and high frequency emissions or supraharmonics that may cause loss of metering and control data. In this paper, the influence of various energy resources on Narrowband Power Line Communications is described and analyzed through several test measurements performed in a real microgrid. Accordingly, the paper describes the effects on smart metering communications through MAC layer analysis. Results show that the commutation frequency of inverters and the presence of battery chargers are remarkable sources of disturbance in low voltage distribution networks. In this sense, the results presented can contribute to efforts towards standardization and normative of emissions at higher frequencies higher, such as CENELEC EN 50160 and IEC/TS 62749.

For the purpose of improve the sustainability of products sold in the EU, Digital Product Passports is a mandatory solution. These passports would systematically gather information about products, such as detailing the materials involved to aid recycling and remanufacturing efforts, or recording the emissions produced throughout the manufacturing process. The overall goal is the establishment of a circular economy in the EU. Current research on Digital Product Passports is focused on collating content for sector-specific applications. However, achieving sustainability goals through Digital Product Passports will require new methods and technical solutions for digital collaboration between supply chain participants, especially in the manufacturing sector. Collaborative work on Digital Product Passports requires trust and traceability in data and access management to ensure privacy over the data contained. One way to enable this securely and confidentially is through the use of blockchain technology, in which stored data cannot be concealed, which is key to the traceability of digital product data documentation. This paper therefore presents a concept for the implementation of generically applicable cross-industry blockchain-based digital product passports. To this end, generic supply chain processes have been abstracted and condensed into the architecture of smart contracts. Great attention is paid to the establishment of traceability as well as privacy through the selection of the blockchain technology Secret Network in combination with Gaia-X functionalities. An illustrative use case for digital product passports in manufacturing is used to demonstrate the applicability of the presented concept. In this use case information about the digital nameplate and carbon footprint is exchanged securely and confidentially in a multi-tenant supply chain network based on the Industry 4.0 infomation model of the Asset Administration Shell.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

Keeping the bus voltage within acceptable limits depends on dispatching reactive power. Power quality improves as a result of creating an effective power flow system, which also helps to reduce power loss. Therefore, Optimal Reactive Power Dispatch (ORPD) studies aim at designing appropriate system configurations to enable a reliable operation of power systems. Establishment of such a configuration is handled through control variables in power systems. On the other hand, installing Distributed Generation Unit (DGU) into a power system can have an important effect on power quality and power loss minimization. In this paper, Grey Wolf Optimization (GWO method is applied to ORPD problem for the first time, to find optimal placement of newly installed DGUs at the power system. Active power loss and voltage minimization have been minimized by optimizing the control variables while keeping them within their upper and lower bounds, and by finding the optimal placement of a newly installed DGU in power system. On the basis of IEEE 30 bus and IEEE 118 bus systems, performance of the suggested approach is investigated. A comparison is also performed among the proposed method and some other methods. Test results demonstrate that the resulting configuration contributes to growing the rate of renewable integration to a power system. The results also indicate that the suggested optimization approach applied to ORPD problem has improved power system performance in terms of both on power loss and voltage deviation. The promising results highlight the potential of the GWO algorithm to facilitate the integration of renewable power sources, and its role in promoting sustainable energy solutions.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

Appropriate animal models of human diseases are a cornerstone in the advancement of science and medicine. To create animal models of neuropsychiatric and neurobehavioral diseases such as ASD necessitates the development of sufficient neurobehavioral measuring tools to translate human behavior to expected measurable behavioral features in animals. Indeed, at least in rodents, adequate neurobehavioral and neurological tests have been developed. Since ASD is characterized by a number of specific behavioral trends with significant severity, animal models of autistic-like behavior have to demonstrate the specific characteristic features, namely impaired social interactions, and communication, restricted, repetitive behavioral patterns with association to several additional impairments such as somatosensory, motor and memory impairments. Thus, an appropriate model must show behavioral impairment of a minimal number of neurobehavioral characteristics using an adequate number of behavioral tests. The proper animal models enable the study of ASD like-behavior from the etiologic, pathogenetic and therapeutic aspects. From the etiologic aspects, models have been developed by the use of immunogenic substances like polyinosinic-polycytidylic acid (PolyIC), Lipopolysaccharide (LPS) and propionic acid or other well-documented immunogens or pathogens, like mycobacterium tuberculosis. Another approach is the use of chemicals like valproic acid, Polychlorinated biphenyls (PCBs), organophosphate pesticides - chlorpyrifos (CPF) and others. These substances were administered either prenatally, generally after the period of major organogenesis, or, especially in rodents, during the early postnatal life. In addition, using modern genetic manipulation methods, genetic models have been created of almost all human genetic diseases that are manifested by autistic like behavior (i.e. fragile X, Rett syndrome, SHANK gene mutation Neuroligin genes and others). Ideally, we should not only evaluate the different behavioral modes affected by the ASD-like behavior but also assess the severity of the behavioral deviations by an appropriate scoring system, as applied to humans.

Atta capiguara is a grass-cutting ant species frequently found in Cerrado biome. However, little is known about the giant nest architecture of this ant. In this study, we investigated the architecture of three A. capiguara nests from the fragment of cerrado in Botucatu, São Paulo, Brazil. Casts were made of the nests by filling them with cement to permit better visualization of internal structures such as chambers and tunnels. After excavation, the depth and dimensions (length, width, and height) of the chambers were measured. The results showed the typical shape of Atta capiguara nests consisting of mounds of loose soil with unique features resembling a conic section. The fungus chambers were found outside the apparent main part of the nest and were spaced apart and distributed laterally at ground level. The waste chambers were located beneath the largest mound of loose soil. Both the fungus and waste chambers exhibited a sectoral distribution. Our study contributes to a better understanding of the so far unknown nest architecture of the grass-cutting ant A. capiguara.

Background/Objectives: The aim of this study was to investigate feasibility and safety of neuromuscular electrical stimulation (NMES) in patients on extracorporeal membrane oxygenation (ECMO) and assess thoroughly any potential adverse events. Methods: We conducted a safety and feasibility study including 16 ICU patients on ECMO support who were admitted to the cardiac surgery ICU from January 2022 to December 2023. Patients underwent a 45-minute NMES session, still on ECMO support, that included a warm up phase of 5 minutes, a main phase of 35 minutes and a recovery phase of 5 minutes. NMES was implemented on vastus lateralis, vastus medialis, gastrocnemius and peroneus longus muscle of both lower extremities. Two stimulators delivered biphasic, symmetric impulses of 75 Hz, with 400 μsec pulse duration, 5 sec on (1,6 sec ramp up and 0,8 sec ramp down) and 21 sec off. The intensity levels aimed to cause visible contractions and be well tolerated. Primary outcomes of the study were feasibility and safety, evaluated by whether the NMES sessions were successfully achieved, and by any adverse events and complications. Secondary outcomes included indices of rhabdomyolysis from biochemical blood test, 24 hours after the application of NMES. Results: All patients successfully completed their 45-minute NMES session, without presenting hemodynamic deterioration, adverse events or signs of rhabdomyolysis. The majority of patients achieved type 4 and 5 quality of muscle contraction. Conclusions: NMES is a safe and feasible exercise methodology in patients supported with ECMO.

Strong yet ductile alloys have long been desired for industrial applications to enhance structural reliability. This work produced two (CoCrNi)93.5Al3Ti3C0.5 medium-entropy alloys with exceptional strength-ductility combinations, via short/medium (3 min/30 min)-time annealing after hot-rolling. Three types of intergranular precipitates including MC, M23C6 carbides, and L12 phase were detected in both the samples. Noticeably, the high density of intragranular L12 precipitates were only founded in the medium-time annealed sample but not in another one. Upon inspection of deformed substructure, it was revealed that the plane slip is the dominant deformation mechanism of both the alloys. This is related to the lower stacking fault energy, higher lattice friction induced by C solute, and slip plane softening caused by intragranular dense L12 precipitates. Additionally, we noted that the stacking fault and twinning act as the mediated mechanisms in deformation of the short-time annealed alloy, while only the former in the medium-time annealed one. It is attributed to the higher energy stacking faults and the increased critical twinning stress caused by intragranular dense L12 precipitates that inhibited the twinning tendency. Our present findings provide not only a guidance for optimizing the mechanical properties of high/medium-entropy alloys, but also a fundamental understanding of deformation mechanisms.

Facing global warming consequences is a major issue of present times. For what concerns climate, projections say that heavy rainfalls are going to increase with high probability together with temperature rise, thus also the hazard related to rainfall induced shallow landslides will likely increase in density over susceptible territories. Different modeling approaches exist and any of them is forced to make simplifications in order to reproduce landslide occurrences over space and time. Process based models can help in quantifying the consequences of heavy rainfall on the different involved processes. In this paper, a narrative review about physically-based deterministic distributed models (PBDDMs) is presented. Models were selected based on: the adoption of the infinite slope scheme (ISS), the use of a deterministic approach (i.e., input and output are treated as absolute values), the inclusion of new approaches in modeling slope stability through the ISS. Models are presented in chronological order with the aim of drawing a timeline of the evolution of PBDDMs and to give researchers and practitioners a basic knowledge on how much has been already done. Results indicate that including vegetation effects on slope stability has raised in importance over time but that there is still the need of finding an efficient way to include them, and that in the last years the literature production seems to be more focused on probabilistic approaches.

With the development of the energy sector based on renewable primary sources, structural changes are emerging for the entire national energy system. Initially, it was estimated that energy generation based on fossil fuels would decrease until its disappearance. However, the evolution of CO2 capture capacity leads to a possible coexistence for a certain period with the renewable energy sector. The paper develops this concept of coexistence of the two systems, with the positioning of green hydrogen not only within the renewable energy sector but also as a transformation vector for carbon dioxide captured in the form of synthetic fuels such as CH4 and CH3OH. The paper also analyzes the economic aspects related to price differences for energy produced in the two sectors, as well as their interconnection. The technical aspect, as well as the economic one, for storage through various other solutions besides hydrogen, has been highlighted. The development of the renewable energy sector and its demarcation from the fossil fuel energy sector, even with the transcendent vector represented by green hydrogen, leads to the deepening of dispersion aspects between the electricity sector and the thermal energy sector, a less mentioned aspect in current works but of great importance.

In the DC distribution networks, DC bus voltage is maintained by the grid-connected converter, the controllability and reliability of the grid-connected converter significantly affects the bus voltage characteristic. To address the problem of limited stability and frequent oscillations, this paper proposes a state feedback control method for the AC/DC converter. Conventional AC/DC converter adopts the voltage-current double-closed-loop control structure with the proportional integral (PI) controllers, which is the equivalent of the typical type II control system, but the typical type II control system cannot fully settle the stability and immunity problems. In contrast, the state feedback control strategy not only achieves the control objectives of the traditional double-closed-loop control, but also reduce the AC/DC converter system model to a typical I-type system, which improves the stability, thus enhances the oscillation suppression capability of the bus voltage. By selecting multiple state variables and designing the converter pole configuration range, the proposed single-loop state feedback control method manages to optimize both the dynamic and steady-state performances of the grid-connected AC/DC converter. Finally, the effectiveness of the proposed single-loop state feedback control strategy has been verified by both the simulation and experiment results.

One of the most crucial and economically beneficial tasks for energy customer is peak load curtailment. On account of the fast response of renewable energy resources (RERs) such as photovoltaic (PV) units and battery energy storage system (BESS), this task is closer to be efficiently implemented. Depends on the customer peak load demand and energy characteristics, the feasibility of this strategy may warry. When adaptive neuro-fuzzy inference system (ANFIS) is exploited for forecasting, it can provide many benefits to address the above-mentioned issues and facilitate its easy implementation, with short calculating time and re-trainability. This paper introduces a data driven forecasting method based on fuzzy logic for optimized peak load reduction. First, the amount of energy generated by PV is forecasted using ANFIS which conducts output trend, and then, the BESS capacity is calculated according to the forecasted results. The trend of the load power is then decomposed in Cartesian plane into two parts, left and right from load peak, searching for BESS capacity equal. Network switching sequence over consumption is provided by a fuzzy logic controller (FLC) with respect to BESS capacity and PV energy output. Finally, to prove the effectiveness of the proposed ANFIS-based peak shaving method, offline digital time-domain simulations have been performed on a real-life practical test micro grid system in MATLAB/Simulink environment and the results have been experimentally verified by testing on a practical micro grid system with real-life data obtained from smart meter and also, compared with several previously-reported methods.

The energy supply for isolated systems remains a current challenge in Brazil and worldwide, particularly when known solutions are compared regarding cost, the ability to supply energy on demand, and sustainability. In this context, green hydrogen, which has been considered one of the main paths for the decarbonization of the energy chain, is also seen as a potential solution for energy supply in isolated systems. Based on a literature review of articles addressing the topics of green hydrogen and isolated systems, an analysis is conducted on the application of green hydrogen as an energy supply solution for isolated systems. The review identified and collected data on important parameters for comparing solutions, such as CAPEX, OPEX, energy cost, and the price per kilogram of hydrogen. Using these data, analyses were performed to provide an overview of the application of green hydrogen in isolated systems. One of the objectives of this work is to present a comprehensive analysis of the green hydrogen chain and its application in the context of electricity generation, particularly for isolated systems in Brazil.

It is meaningful to monitor and identify the concrete cracks as they will seriously reduce the fatigue life of pavement. In this paper a new method based on distributed long-gauge optic fiber sensing is proposed to implement the crack identification. Firstly, the damage indicator, namely strain curve envelope area ratio (SCEAR), is proposed and calculated with the measured strain in time series when the plane goes across the pavement where the sensors are installed. Then the indicators with different sensors are normalization by the value of the indicator from one referenced sensor where damage normally will not happen. If the crack happens within the sensing gauge of the sensor, the value of damage indicator SCEAR from the sensor will increase. Therefore, the crack will be identified with the change of the damage indicator. The effect of the proposed method is first verified by some simulations of prefabricated pavement as the cracks can be accurately identified by the proposed method. Moreover, the influence from the aircraft, such as taxiing position, aircraft load and aircraft type, is not obvious enough to mislead the identification results. Lastly the static loading tests were implemented with one small-scale model of prefabricated concrete pavement in the lab. From the experimental results the prefabricated cracks inside the pavement slab can be identified accurately with the proposes method as the parameter SCEAR is increased by about 100% at the crack position, while it is only changed by about 3% at the undamaged position.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Civic participation is of great significance to urban management decision-making. In order to facilitate citizens to participate in city management decision-making, this paper proposes a large-scale group decision-making (LSGDM) method based on multi-granular probabilistic linguistic preference relations (MG-PLPRs). First, each decision maker selects a language terms set from the multi-granularity language terms set to represent individual preference relations and the MG-PLPRs are obtained by statistical calculation to represent sub-group’s preferences information. Then, an optimization model based on the expected consistency of PLPR and consensus measure of groups is established to achieving consensus reaching processes, which can ensure satisfactory individual consistency and group consensus. Finally, the validity and applicability of the proposed method is verified by a case of a city "shared garden" site selection with the participation of citizens.

Field of Research This research study investigates the role of distributed leadership and culture within small enterprises in Malta, an area in which there has been very limited research. It focuses on the interaction between these two elements and their impact on organizational behaviour and effectiveness. Several studies (Jardon et al 2019; Cope et al., 2011; de Oliveira et al., 2015; Mohanty et al., 2012;) suggest that effective leadership and culture are vital elements in the successful endeavours of small organizations. Schein (2006) further asserts that they are two different faces on the same coin and the dyadic interaction characterizes “how leaders create culture and how culture defines and creates leaders”. Distributed Leadership is a systematic practice of interactions and synergies between leaders, followers, and the situation (Spillane 2013). It is different from traditional leadership, which involves top-down management because it tends to be more democratic and participatory, whereby influence and decision-making are shared among multiple individuals rather than being controlled by a single leader. (Xhemajli et al. 2022) Methodology Adopting a naturalistic approach and guided by an interpretivist, constructivist epistemological stance, this research delves into the intricate interplay between leadership and culture within small businesses. The chosen research methodology employs Grounded Theory, recognized for its robust and systematic process facilitating the observation of patterns through intensive iterative and highly analytical procedures (Charmaz, 2015).In the initial stages of field research, characterized by 'responsive interviewing' (Rubin and Rubin, 2012), data sampling commenced with convenience sampling. This initial phase gradually evolved into a refined strategy incorporating selective sampling and theoretical sampling (Corbin and Strauss, 2015). The shift in sampling approaches reflects a deliberate focus on collecting data based on its specific contribution to the development and comprehension of the dimensions, properties, and characteristics of key concepts.The induction of theory is a product of successive comparative analyses, involving the systematic comparison of data points to identify both similarities and variations. Abductive reasoning is integral throughout the analytical process, with particular emphasis during constant comparative analysis of categories, leading to theoretical integration (Charmaz, 2006). This meticulous approach aligns with the assertion of Strauss and Corbin (2015) that grounding theory in data enhances the likelihood of deriving theories that authentically reflect reality.The key advantage of using this approach is that the analysis carried out goes beyond deep exploration and rich description and actually develops a framework that explains the phenomena observed (Parker and Roffey, 1997, p.218). This is very important if the findings are to contribute to the knowledge enhancement of any field of practiceThe culmination of this research effort is the presentation of a set of interconnected concepts, intricately woven together into an emergent parsimonious model (Corbin and Strauss, 2015). This model serves to explain the dynamic interplay between leadership and culture, elucidating its tangible impact on the effectiveness of small enterprises. Research Contribution:Implications for Practice This research contributes to the literature on leadership and organizational culture in small enterprises, particularly in the context of Malta where such studies are scarce. By providing an initial exploration of these phenomena and their impact on organizational behavior, this paper lays the groundwork for further inquiry into this important area. Furthermore, the study offers practical insights for leaders of small enterprises by elucidating leadership behaviors observed in established organizations. Through applied cases, it demonstrates how the abstract concept of culture can be translated into a practical instrument that supports leadership and organizational development. This not only enriches the understanding of leadership dynamics but also provides tangible strategies for implementation. Moreover, the research contributes empirical evidence on the development of leadership functions within small enterprises, emphasizing the potential of shared and distributed leadership models. By grounding its findings in data, the study equips leaders with a deeper understanding of how these leadership approaches can shape organizational development, fostering more effective management practices in small businesses. Methodologically, the adoption of Grounded Theory methodology showcases its efficacy in exploring complex management phenomena. By employing this approach, the researchers were able to gather rich descriptions and develop an explanatory framework, highlighting its applicability in studying nuanced organizational dynamics. Implications for Policy and Theory This research also holds significant implications for policymakers, academic researchers and institutions involved in supporting small businesses. By providing insights into distributed leadership and cultural influences on organizational effectiveness, it offers a basis for informed policy formulation and support mechanisms. The conceptual model emerging from this study serves as a foundation for designing more targeted policies that cater to the unique needs of small enterprises. By understanding the intricacies of leadership dynamics and cultural contexts, policymakers can develop interventions that foster a conducive environment for small business growth and sustainability. Additionally, academic researchers can use these findings to further refine theoretical frameworks and empirical studies in the field, contributing to ongoing scholarly dialogue and knowledge advancement.

This review study explores and analyzes distributed database management systems (DDBMS), focusing on the important role of transparency methods in improving the functioning and interaction between users and systems. Transparency in DDBMS refers to several important factors, such as data, replication, performance, scaling, and network transparency. Each one of these components plays a role in concealing the intricate operations that underlie distributed systems from the end user. This not only speeds interactions but also enhances the reliability of the system. The article highlights the criticality of data independence as well as replication transparency in particular. Data independence enables adaptable modifications to the system's architecture and alterations to be made without causing any disruption to user activities. On the other hand, replication transparency ensures that the data remains consistently accurate across distributed nodes, even in the absence of user awareness. Moreover, the article investigates the progression of DDBMS through the incorporation of cutting-edge technologies such as quantum computation and artificial intelligence, which are anticipated to significantly augment the capabilities of data processing. The text proposes potential avenues for further investigation, emphasizing how these advancements may enhance the fundamental resilience of database management systems (DBMS) and expand their applicability in intricate, data-rich settings.

This paper addresses the evolving landscape of electricity markets in Europe, with a focus on the integration of Renewable Energy Communities as introduced by the Renewable Energy Directive 2018/2001. Residents within a postal code area are highly incentivized to join a community, which enables them to exchange energy among themselves at lower procurement costs. Thereby, energy management systems optimize the operation of respective energy systems, with electrical load forecasting playing a key role. Given that prosumers may switch between communities on a daily basis, electricity demands within these groups will vary, leading to data that is non-stationary, discontinuous as well as non-identical and independently distributed. To encounter this issue, we propose a sophisticated forecasting model that applies federated learning, using informations from various distributed communities to learn domain-invariant features. To achieve this, we initially utilize synthetic electrical load time series at district level and aggregate them to profiles of Renewable Energy Communities with dynamic portfolios. Subsequently, we develop a forecasting model that accounts for the composition of residents of a Renewable Energy Community, adapt data pre-processing in accordance with the time series process, and detail a federated learning algorithm that incorporates weight averaging and data sharing. Following the training of various experimental setups, we ultimately evaluate their effectiveness. The findings suggest that our proposed framework is capable of effectively forecast non-stationary and discontinuous time series and that it can be applied to new, unseen data through the integration of knowledge from multiple sources.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

In the context of energy conversion from renewable sources to distribution grids (insulated or not), a converter is often required to transfer energy from a low voltage source, towards three-phase grids. This paper presents the HW design, the simulation results and the conversion performance of a CSI converter intended to interface low voltages renevable sources to three-phase grids. The main focus of this paper is to obtain the best performance in terms of voltage increase towards the output stage while maximizing the conversion efficiency. In comparison with the currently used energy conversion systems for small photovoltaic systems, hereafter some solutions were adopted to level and maximize the energy flow from the source to the DC-link and improve the quality of current supplied in terms of harmonic distortion. The proposed system is composed of two conversion stages: the first, voltage-to-current, the second current-to-current via a three-phase CSI bridge modulated with SVM technique. The stages are not completely decoupled from an electrical point of view, therefore, in order to mitigate the effects of these interactions, synchronization strategies have been adopted.

The monitoring of coastal waters using satellite data, from sensors including Sentinel-3 OLCI, has become a vital tool in the management of these water environments; especially when it comes to improving our understanding of the effects of climate change on these regions. In this study, Level-2 water products derived from different OLCI Sentinel-3 processors were validated against a comprehensive in situ dataset from the NW Baltic Sea proper region. The products validated were those of the regionally adapted Case-2 Regional Coast Colour (C2RCC) OLCI processor (v1.0 and v2.1), as well as the latest standard Level-2 OLCI case 2 (Neural Network) products from Sentinel-3’s processing baseline: Baseline Collection 003 (BC003), including “CHL_NN”, “TSM_NN”, and “ADG443_NN”. Furthermore, the effect of the current EUMETSAT system vicarious calibration (SVC) on the Level-2 water products was also validated. Results showed that the system vicarious calibration (SVC) reduces the reliability of the Level-2 OLCI products. For example, the application of these SVC gains to the OLCI data for the regionally adapted v2.1 C2RCC products resulted in RMSD increases of 36% for “conc_tsm”; 118% for “conc_chl”; 33% for “iop_agelb”; 50% for “iop_adg”; and 10% for “kd_z90max” using a ±3h validation window. The findings indicate that the current EUMETSAT SVC gains should be applied and interpreted with caution in the region of study at present. A key outcome of the paper recommends the development of a regionally specific SVC against AERONET-OC data for the region.

Despite soccer popularity, comparatively little scientific information is available concerning the assessment of youth players’ physiological characteristics. The use of medical software integrating wearable sensors to provide accurate and objective data is necessary. In the present study, the objective assessment of physical performance of 128 adolescent soccer players at two timepoints (pre-season and end-season) has been performed. Participants completed a comprehensive test battery including stability, countermovement jumps (CMJ), plyometric jumps (PJ), agility, and quick feet tests. A single Inertial Measurement Unit (IMU) sensor provided quantitative data on various performance metrics. Principal Component Analysis (PCA) reduced the dataset to four principal components (PCs) explaining over 80% of the variance: power (PC1), balance (PC2), speed/agility (PC3), and stiffness (PC4). Paired samples t-test between the two timepoints showed no significant differences in the PCs between the two timepoints, indicating that the training program did not significantly alter the assessed physical attributes. However, subtle individual changes may still inform personalized training adjustments. The study highlights the importance of continuous monitoring and individualized training strategies to optimize athlete performance and reduce injury risk.

Virus taxonomy uses a Linnaean-like subsumption hierarchy to classify viruses into taxonomic units at species and higher rank levels. Virus species are considered monophyletic groups of mobile genetic elements (MGEs) often delimited by phylogenetic analysis of aligned genomic or metagenomic sequences. Taxonomic units are assumed independent organizational, functional and evolutionary units that follow a ‘natural’ historical rationale. Here, I use phylogenomic and other arguments to show that viruses are not self-standing genetically-driven biological systems. Instead, they are crucial components of holobionts, units of biological organization that dynamically integrate the genetics, epigenetic, physiological and functional properties of their co-evolving members. Remarkably, phylogenomic analyses show viruses share protein domain and loop structures with cells throughout history via massive processes of reticulate evolution, helping spread evolutionary innovations across a wider taxonomic spectrum. Thus, viruses are not merely MGEs or microbes. Instead, their genomes and proteomes conduct cellularly integrated processes akin to those cataloged by the GO Consortium. This prompts the generation of compositional hierarchies that replace the ‘is-a-kind-of’ by a ‘is-a-part-of’ logic to better describe the mereology of integrated cellular and viral makeup. My analysis demands a new paradigm that integrates virus taxonomy into a modern evolutionarily centered taxonomy of organisms.

The purpose of this paper is to explore the implementation of Retrieval-Augmented Gen- 14 eration (RAG) technology with open-source Large Language Models (LLMs). For this purpose, a 15 web-based application named PaSSER that integrates RAG with three models - Mistral:7b, 16 Llama2:7b: Orca2:7b, is developed. In its development various technologies are used, including 17 Blockchain for managing and storing assessment results of built-in testing modules. PaSSER em- 18 ploys a set of evaluation metrics for LLMs’ performance - METEOR, ROUGE, BLEU, Perplexity, 19 Cosine similarity, Pearson correlation, and F1 score. The specialized knowledge base is in the smart 20 agriculture domain. As an illustration, the paper presents results and analysis of two tests. First one 21 is assessing the performance of LLMs across different hardware configurations, the other is deter- 22 mining the model that delivers most accurate and contextually relevant responses within the RAG. 23 The paper also discusses the integration of blockchain technology with LLMs to manage and store 24 assessment results within a blockchain environment. The tests revealed that Mistral:7b demon- 25 strates the best results across most of the evaluated metrics. The discussion section comments on 26 technical and hardware considerations that affect the performance of LLMs. Future development 27 will focus in leveraging new larger pre-trained open-source LLMs, exploring different finetuning 28 approaches, and further integration with Blockchain and IPFS.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

High resolution information on nucleotide arrangement in the genome of any or-ganism is critical to understand its genetic makeup, function, and evolutionary his-tory. For years, DNA sequencing has provided crucial breakthroughs in the field of genomics and molecular biology. With the advent of technology, Next Generation Sequencing has now transformed the whole genome sequencing prospects, thus unveiling the novel and interesting features of an organism genome that can behold. Next generation sequencing platforms offer realistic approach to identify and anal-yses whole genome with high throughput, accuracy, scalability in a very short time span. Information obtained can be further used in improving our existing healthcare systems, designing novel and personalized therapeutic modules, making the envi-ronment sustainable and proactively preparing ourselves for future pandemics and outbreaks. This article discusses the various NGS technologies and approaches, their advantages, drawbacks, and futuristic usage in different fields. Though still in nascent stages and marred with flaws, with ongoing advancement, NGS will indeed have promising impacts in the future.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

Distributed Denial of Service (DDoS) is among the commonly used type of network attacks, particularly aimed at the IoT devices in the emerging future wireless services specially for strictly latency-limited applications. DDoS attacks pose serious threats for many entrepreneurial businesses as they can prevent legitimate customers from accessing network resources of corporate websites, demanding intelligent analytics prior to entertaining a service request. DDoS involves exploiting the vulnerability of IoT devices by launching distributed multi-point attacks to generate high traffic by flooding the network of victims. The consequences of DDoS attacks could be worst in any Software-Defined Networking (SDN) than in traditional networks because SDN is configured as centralised architecture, failing to address the weaknesses current paradigm. However, SDN can play a crucial role in mitigating the effects of DDoS attacks as it bears the features of easy programmability, manageability, flexibility, and scalability. In this manuscript preliminary framework to detect DDoS attacks by mitigating their threats in an SDN architecture is presented. The authors propose a defense mechanism that uses OpenFlow and sFlow to mitigate the effects of DDoS attacks. The initial results show that the proposed model can minimize efficiently the consequences of DDoS attacks in an SDN type of architectural paradigm.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

The concept of Research Integrity and research ethics are linked to the scientific research process and its communication. Presenting the results objectively is essential. It turns out that few scientists use manipulation of results and consequently other types of misconduct such as data Fabrication, Falsification, and Plagiarism (FFP). In this article, we show the definitions of these and different aspects of behavior that should be avoided, which affect principles of research reliability. We present, through a brief literature review, the concept of Research Integrity, FFP, and its relations with Publish or Perish. Editorial disputes are linked to the power that scientists have to remain in the field of research, governed by clear rules to increase their intellectual capital. We discussed that scientists tend to want their papers published in journals with better impact and well-evaluated, seeking prominence in the publishing sector. We have seen that both scientists and journals can have sequelae and problems in the face of the Publish or Perish movement, which can call into question the quality of the editorial process, peer review, and the journal itself.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

Nasal high-frequency oscillatory ventilation (nHFOV) has emerged as an effective initial and rescue noninvasive respiratory support mode for preterm infants with respiratory distress syndrome (RDS). Multiple noninvasive respiratory support modes are currently available in Romania, but little is known about nHFOV use in Romanian neonatal intensive care units (NICUs). We aimed to identify the usage extent and clinical application of nHFOV in Romania. A structured web-based questionnaire was designed to find the rate of nHFOV use and knowledge of this new method of noninvasive respiratory support in Romanian level III NICUs. The questionnaire was addressed to the leaders of all level III Romanian NICUs. Using multiple-choice, open-ended, and yes/no questions, we collected information on the NICU’s size, noninvasive respiratory support modes used, nHFOV use, indications, settings, nasal interfaces, secondary effects, and equipment used. Descriptive statistics and comparisons were performed using IBM SPSS Statistics 26.0. A total of 21/23 (91.3%) leaders from level III NICUs (median [IQR] number of beds of 10 [10-17.5]) responded to the survey. The most frequently used noninvasive ventilation modes were CPAP mode on mechanical ventilators (76.2%), followed by NIPPV (76.2%), heated, humidified high flow nasal cannula (HHHFNC) (61.9%), and nHFOV (11/21 units; 52.4%); 5/11 units reported frequent nHFOV use (in 2 or more newborns/month) in both term and preterm infants. The main indications reported for nHFOV use were CPAP failure (90.9%), hypercapnia (81.8%), and bronchopulmonary dysplasia (72.7%). 10/11 units reported setting a mean airway pressure (MAP) equal to the CPAP level plus 1-2 cmH₂O on rescue nHFOV after CPAP failure. Both dedicated equipment (45.5%) and hybrid ventilators (63.6%) were used for nHFOV delivery, with face/nasal masks and short binasal prongs being the most commonly used nasal interfaces (90.9% and 72.7%, respectively). Air leaks at the interface level (90.9%), thick secretions (81.8%), and airway obstruction (63.6%) were the most frequently mentioned adverse effects of nHFOV; none of the units mentioned pneumothorax as an adverse effect. Only 3 of the NICUs had a written protocol for nHFOV use. Initial, minimum, and maximum amplitude and initial and minimum MAP settings used were significantly higher with hybrid ventilators as compared to dedicated equipment (p<0.05). Most units not yet using nHFOV cited lack of equipment, experience, training, or insufficient information and evidence for the clinical use and outcome of nHFOV use in neonates as the main reasons for not implementing this noninvasive respiratory mode. Our survey showed that nHFOV is already used in more than half of the Romanian level III NICUs to support term and preterm infants with respiratory distress despite a lack of consensus regarding indications and settings during nHFOV. A need for training for nHFOV use was identified, and efforts are needed at the national level to develop courses and training sessions, including using simulation workshops, to offer more information on optimal nHFOV use in clinical practice.

Recommender Systems (RecSys) are crucial in managing information overload and enhancing user satisfaction across various digital platforms, including e-commerce and entertainment. Evolving from traditional models to Deep Neural Networks (DNNs) and, more recently, Large Language Models (LLMs), these systems leverage sophisticated algorithms to analyze user behaviors and preferences. LLMs, such as GPT-4, are trained on extensive datasets to comprehend and generate natural language, significantly advancing their ability to deliver personalized recommendations. This tutorial explores the transformative impact of LLMs on RecSys, discussing their development, application in handling complex datasets, and the integration of contextual insights. Real-world examples illustrate how LLMs enhance recommendation accuracy and user experience, highlighting challenges and future directions in the field.

It is shown that if there exists in nature a pair of heavy elementary particles each with a charge equal to that of the proton and with mass energy , then their direct interaction gives rise to a spontaneous fractionation of the two charges into three pairs of elementary particles according to two equiprobable channels, one hadronic and one leptonic. The leptons and quarks produced are in agreement with the first generation of the Standard Model of matter. Fractionation suggests the relative abundances of the elementary particles, introducing some questions about the possibility of the real existence of a currently unknown particle and its role in the formation of an apparent matter-antimatter asymmetry in the universe.

The architectural configuration of the space plays a crucial role in the acoustics of Neonatal Intensive Care Units (NICUs). The design of the environment, the materials used in construction, and the organisation of noise sources within the room significantly influence the noise levels present in these critical areas. For this research, noise levels found in two hospitals, with different architectural configurations and sizes but similar construction materials, have been analyzed. Data were recorded at 1-second intervals over a period of more than 24 hours. The data collected in these hospitals confirm the magnitude of the noise problem in NICUs, highlighting the urgent need to address it effectively to ensure an appropriate and safe environment for the recovery of neonates. Good architectural planning can help mitigate noise, while poor configuration can exacerbate acoustic problems, negatively affecting both patients and healthcare staff. It is crucial to involve architects, acoustic engineers, and healthcare staff in the design and renovation of NICUs to create spaces that not only meet medical needs but also consider the auditory well-being of neonates.

Reviewed are recent efforts leading to chemo-enzymatic syntheses of strongly fluorescent ribosides of nucleobase analogs, potentially applicable in analytical biochemistry and cell biology. Described are syntheses and properties of fluorescent purine, 8-azapurine and etheno-purine ribosides, obtained using various types of the purine nucleoside phosphorylase (PNP) as catalysts of ribosylation, and -ribose-1-phosphate (r1P) as a second substrate. In several instances, the ribosylation sites were different than the canonical purine N9. Some of the obtained ribosides show fluorescence yields close to 100%. Their main applications are assays of PNP, nucleoside hydrolases, and other enzyme activities both in vitro and, possibly, within the living cells, using fluorescence microscopy.

This study investigates job satisfaction, burnout, and well-being among first-generation migrant physicians in anesthesia and intensive care medicine in Germany, comparing them to their native German counterparts. Utilizing a cross-sectional survey design, the study collected data from 513 physicians, 110 of whom identified as having a migration background. Job satisfaction was measured using the German version of the Warr-Cook-Wall (WCW) Job Satisfaction Scale, burnout was assessed with the Copenhagen Burnout Inventory (CBI), and well-being was evaluated using the WHO-5 Well-Being Index. The job satisfaction ratings revealed no significant differences between migrant and German physicians in most dimensions, including physical workload, freedom to choose work methods, satisfaction with colleagues, responsibility, income, skill utilization, and variety in work tasks. However, migrant physicians reported significantly higher satisfaction with recognition received for their work and lower dissatisfaction with working hours. Burnout assessments showed that migrant physicians experienced higher psychological strain, perceiving every work hour as more exhausting and having significantly less energy for family and friends. Notably, migrant physicians reported higher difficulty and frustration in working with patients. Well-being ratings indicated that migrant physicians felt less energetic and active but found their daily life more filled with interesting activities. The findings underscore the unique challenges faced by migrant physicians, particularly in terms of recognition and patient-related burnout. These results highlight the need for targeted interventions to support migrant physicians, including cultural competence training and flexible working hours to enhance their job satisfaction and overall well-being. Addressing these issues is crucial for maintaining the quality of patient care and the occupational health of migrant physicians in Germany.

Despite significant advancements in Artificial Intelligence (AI) and Large Language Models (LLMs), detecting and mitigating bias remains a critical challenge, particularly within social media platforms like X (formerly Twitter) and in addressing cyberbullying present on them. This research investigates the effectiveness of leading LLMs in generating synthetic biased and cyberbullying data and evaluates the proficiency of Transformer AI models in detecting bias and cyberbullying within both authentic and synthetic contexts. The study involves semantic analysis and feature engineering on a dataset of over 48,000 sentences related to cyberbullying collected from Twitter (before it became X). Leveraging state-of-the-art LLMs such as ChatGPT-4o, Pi AI, Claude 3 Opus, and Gemini-1.5, synthetic biased, cyberbullying, and neutral data were generated to deepen the understanding of bias in human-generated data. AI models including DeBERTa, Longformer, BigBird, HateBERT, MobileBERT, DistilBERT, BERT, RoBERTa, ELECTRA, and XLNet were initially trained to classify Twitter cyberbullying data and subsequently fine-tuned, optimized, and quantized for multilabel classification (detecting both biases and cyberbullying). The study's outcomes include a prototype of a hybrid application that combines a Bias Data Detector and a Bias Data Generator, validated through extensive testing.

Storage, transmission and processing of data become a significant problem when large digital data files or databases are involved, as in the case of decentralized online global databases such as blockchain. Here we propose a novel method that allows the scalability of digital assets, including blockchain databases in the download, validation and confidentiality process, by developing a lightweight blockchain technology called Entropic Blockchain. This is a computer-implemented mathematical method to generate an information-entropic numerical representation of a digital asset, which can be utilized on its own, or as an optically machine-readable entropic barcode, for data secure transmission, processing, labelling, identification, one-way encryption and compression, validation, and digital tamper-proof check.

This study considers an application of the first-order Grey Markov Model to foresee the values of Italian power generation in relation to the available energy sources. The model is used to fit data from the Italian energy system from 2000 to 2022. The integration of Markovian error introduces a random element to the model, which is able now to capture inherent uncertainties and misalignments between the Grey model predictions and the real data. This application provides valuable insights for strategic planning in the energy sector and future developments. The results show good accuracy of the predictions, which provides powerful information for the effective implementation of energy policies concerning the evolution of energy demand in the country. Despite advancements, Italy’s 2032 energy mix will still significantly rely on fossil fuels, emphasizing the need for sustained efforts beyond 2032 to enhance sustainability.

Deadlock is a real problem that can cause expensive, time-dependent hang-ups or failures in distributed computing systems. Some studies have been conducted with deadlock detection and resolution in generalized request computing models, most of these studies are based on the diffusing computation scheme, where forward and backward propagated probe and reply messages respectively are diffused between dependent processes. The replies carry the dependency information between processes for the initiator. Using this dependency information initiator can detect and resolve the deadlock cycle. It has been proven in the literature that a deadlock cycle length distribution is skewed with a large majority of cycles (90%) having length two. Based on this fact an improved algorithm is proposed for handling deadlock detection in distributed computing systems under the distributed request model where each process has several requests at a time. The improved algorithm depends mainly on message propagation and timeout policy. Probe and reply messages are propagated between the initiator and its successors only to detect deadlock cycles between them. Global timeout policy is used to detect potential deadlock cycles with large length distribution. The proposed algorithm can handle concurrent executions. Simulation experiments are performed to see the effectiveness of the improved algorithm. It is found that the improved algorithm compares favorably with other existing algorithms and it shows better results for several performance metrics especially in reducing deadlock latency and execution time.

The wastewater problem is becoming an increasingly significant environmental issue affecting various aspects of human activities. The generation of reactive oxygen species (ROS) in water through certain physicochemical processes, which can oxidize or degrade various organic and chemical compounds, offers an effective purification method. The main advantage of these methods is the elimination of chemical reagents. Aim of this work is to investigate the possibility of regulating the ROS content in water by altering the characteristics of the plasma discharge that occurs under hydrodynamic cavitation in the water flow. ROS concentration was determined using the permanganate oxidation titration technique. It was found that the content of various reactive oxygen species in water after treatment can be controlled by varying the power of the electrical pulses applied. Additionally, the study obtained the dependence of ROS concentration in treated water samples on storage time, indicating a prolonged effect of sonoplasma treatment on the antibacterial properties of water. Analysis of water samples using a biological test culture of Salmonella typhimurium revealed bacteriostatic properties of the water for at least 48 hours after sonoplasma discharge treatment.

Synergistic control of emissions of air pollutants and CO2 is critical to the dual challenges of air quality improvement and climate change in China. Based on the emission inventories of thermal power units in Beijing, Tianjin, and Hebei, this study analyzes the CO2 and NOX emission characteristics of these units, identifies and quantifies the synergistic drivers affecting these emission trends. Inventory data show that between 2010 and 2020, NOX emissions were reduced by 86.1%, while CO2 emissions were reduced by only 29.8%. Although significant progress has been made in reducing NOX emissions through measures such as end-of-pipe treatment, controlling CO2 emissions remains a difficult task. The index decomposition analysis reveals that economic growth is the main driver of CO2 and NOx emission growth, energy intensity reduction is the main driver of CO2 emission reduction, and end-of-pipe treatment is the main driver of NOX emission reduction. Currently, coal occupies about 87% of the energy consumption of thermal power units in the Beijing-Tianjin-Hebei, and remains the main type of energy for synergistic emissions, and the potential for emission reduction in the energy structure remains huge. For NOX emissions, it is expected that 90% of the reduction potential can be achieved through energy restructuring and end-of-pipe treatment. In conclusion, the high-precision unit-by-unit emission study confirms the effectiveness of the control policy for thermal power units in the region and provides some scientific reference for future policy formulation.

This paper designed a new type of generator, transgenerator, that integrates the wind turbine and flywheel into one system, aiming to make the flywheel distributed energy storage (FDES) more modular and scalable than the conventional FDES. The transgenerator is a three-member dual-mechanical-port (DMP) machine with two rotating members (inner and outer rotors) and one stationary member (stator). The transgenerator-flywheel system is introduced with the system configuration, transgenerator overview, flywheel operation principle and power management strategies, and control system. Simulations are performed in MATLAB/ Simulink to verify the system viability, including control system verification and the flywheel storage performance evaluation. Results show that the inner and outer rotors can be controlled independently with accurate and fast control response, and the grid-side control works properly. The flywheel performs well with considerable charging power and storage capacity.

While Retrieval-Augmented Generation (RAG) enhances Large Language Models (LLMs), it also presents challenges that can affect model accuracy and performance. Practical applications show that RAG can mask the intrinsic capabilities of LLMs. Firstly, LLMs may become overly dependent on external retrieval, underutilizing their own knowledge and inference abilities, which can reduce responsiveness. Secondly, RAG techniques might introduce irrelevant or low-quality information, adding noise to the LLM. This can disrupt the normal generation process, leading to inefficient and low-quality content, especially when dealing with complex problems. This paper proposes a RAG framework that uses reflective tags to control retrieval. This framework evaluates retrieved documents in parallel and incorporates the Chain of Thought (CoT) technique for step-by-step content generation. The model selects the highest quality and most accurate content for final generation. The main contributions include: 1) Reducing the hallucination problem by selectively utilizing high-scoring document, 2) Enhancing real-time performance through timely external database retrieval, and 3) Minimizing negative impacts by filtering out irrelevant or unreliable information through parallel content generation and reflective tagging. These advancements aim to optimize the integration of retrieval mechanisms with LLMs, ensuring high-quality and reliable outputs.

The rapid and accurate detection of viruses and the discovery of single nucleotide polymorphisms (SNPs) are crucial for disease management and understanding viral evolution. In this study, a pipeline for virus detection, validation, and SNP discovery from next-generation sequencing (NGS) data is presented. By integrating state-of-the-art bioinformatics tools with artificial intelligence, the pipeline processes raw sequencing data to identify viral sequences with high accuracy and sensitivity. Before aligning the reads to the reference genomes, quality control measures and adapter trimming are performed to ensure the integrity of the data. Unmapped reads are subjected to de novo assembly to reveal novel viral sequences and genetic elements. The effectiveness of the pipeline is demonstrated by the identification of virus sequences, illustrating its potential for the detection of known and emerging pathogens. SNP discovery is performed using a custom Python script that compares the entire population of sequenced viral reads to a reference genome. This approach provides a comprehensive overview of viral genetic diversity and identifies dominant variants and a spectrum of genetic variations. The robustness of the pipeline is confirmed by the recovery of complete viral sequences, which improves our understanding of viral genomics. This study highlights the synergy between traditional bioinformatics techniques and modern approaches, providing a robust tool for analyzing viral genomes and contributing to the broader field of viral genomics.

Background: The antisense oligonucleotide against APOC3 mRNA volanesorsen was recently introduced to treat Familial Chylomicronemia Syndrome (FCS). Cases of decreased platelet count are reported among patients treated with volanesorsen. The aim of the study is to evaluate platelet function and thrombin generation (TG) assessment in FCS patients receiving volanesorsen. We performed a cross-sectional study on FCS patients treated with volanesorsen. Methods: changes in PLC were assessed from baseline to Tw12 and Tw36. To assess TG, samples were processed by CAT (with PPP-reagent LOW). The results were expressed by the trombogram graphic (thrombin variation over time); lagTime; Endogenous Thormbin Potential(ETP); peak; time to reach peak(ttpeak), startTail e velocity Index. Platelet aggregation was assessed by testing different agonists using turbidimetry method. Results: Four FCS patients and 4 matched healthy controls were included in the present study. Changes in PLC at Tw12 was 30% and 34% at T36w. Thrombin generation results show values in normal range (for patients and controls respectively lagTime:10,42±4,40 and 9,25±0,99; ttPeak:14,33± 4,01 and 13,10±0,67; startTail:32,13±3,54 and 29,46±1,69; velocityIndex:20,21±3,63 and 33,05±13,21; ETP 599,80±73,47 and 900,2±210,99; peak value 76,84±1,07 and 123,30±39,45) and no significant difference between cases and controls. Platelet aggregation test showed values in range with no significant difference with healthy controls Conclusions: Our study showed for the first time that no significant changes in the general haemostasis assessed by TG and in platelet function have been observed in FCS patients receiving volanesorsen.

This paper introduces an innovative energy circuit that challenges conventional understandings of energy conservation, marking a significant departure from traditional frameworks. Seeking to enhance energy generation within existing paradigms, this innovation holds promise for addressing pressing global issues such as the energy crisis and environmental sustainability, while also stimulating scientific inquiry. In contrast to prevalent misconceptions rooted in philosophical and scientific constraints, this study refutes the notion of generating energy from nothing and questions the viability of perpetual motion machines as conceptual models. Instead, it proposes a novel circuit design derived from an unconventional electrical short circuit, which is shown to disrupt the established principles of energy conservation. This circuit offers a transformative approach with diverse applications, including self-recharging capabilities for electric vehicles, bolstering microgrid infrastructure, and facilitating the integration of renewable energy sources. Transcending conventional scientific boundaries, this paper prompts philosophical reflections on the evolving nature of scientific exploration. Ultimately, the energy circuit represents a pivotal step towards mitigating the global energy crisis by reducing reliance on finite resources and fostering sustainability. The paper concludes by illustrating the circuit's potential to revolutionize energy systems and contribute to a more resilient and sustainable future.

Remote distributed generation control and demand response is nowadays a basic need, especially for the Distributed Network Operators (DNOs). The integration of Renewable Energy Sources (RES) with stochastic production characteristics into the grid in conjunction with the newly appeared stochastic demand consumers (i.e., electric vehicles) hardens the ef-forts of the DNOs to keep the grid’s operation within safe limits and prevent cascading black-outs while staying in compliance with the SAIDI and SAIFI indices during maintenance and re-pair operations. Taking also under consideration the aging of the existing grid infrastructure, making it year by year more prone to failure, it is yet of great significance for the DNOs to have access to real-time feedback from grid’s infrastructure, fast, with low-cost upgrade interventions, easily deployed on the field and with fast response potential, in order to be able to perform real-time grid management (RTGM). In this article, we describe the architecture, development and deployment of a hybrid real-time control system of distributed generation (DG) units, which has the potential to be applied easily to DNO’s substations, RES plants and consumers (i.e. electric vehicles’ charging stations), that combines a low-cost minimum intervention into the electricity grid and its components and eliminates all communication interoperability problems between the different vendors’ installed electrical equipment.

The sustainable development of an area is highly dependable on reliable electrical energy supply. Microgrids are important in integrating distributed energy resources (DERs) using power electronic converters. However, microgrid control becomes challenging with the increasing number of distributed generators and loads. With the conventional droop control method, power contributions from DER converters cannot be accurately shared due to a mismatch of line impedances. In this paper, an augmented hierarchical control mechanism is proposed to solve the issues mentioned above. This hierarchical control mechanism consists of primary and secondary controllers. The primary stage utilized the droop controller to improve optimal power flow, mainly for the resistive network. The secondary stage is based on an improved methodology to compensate for the voltage and frequency variations during small and large signal disturbances. Moreover, the modelling and analysis for PMSG-based wind energy conversion systems are also presented. The response of the primary controller for the active and reactive power sharing is investigated. The analysis emphasizes the demonstration of optimal power-sharing under normal and abnormal conditions for the considered load. Finally, the suggested robust controller's performance is evaluated in MATLAB environment and simulation results show the proposed scheme's superiority under different operating conditions.

The automotive market is very competitive and presents a demand for the consistent improvement of the used technologies and reduction of the product cost and dimensions with each product model iteration. Hence, it is important to have access to well-defined reference designs of high quality products, in order to evaluate the new ideas and technologies. This paper provides the readers with a numerical model of such a high quality product, i.e., the IPMSM type traction motor from the 4th generation of the Toyota Prius hybrid transaxle. In the introductory section, the brief history of the Prius model is given together with the references to the reverse engineering reports. Afterwards, the machine dimensions, material properties and winding configuration are described. Then, the model is validated with the torque measurements at constant speed. In the next chapters the simulation results are presented and the numerical source data are supplied to the reader. Finally, the design philosophy of the Toyota drive is briefly discussed in comparison with the BMWi3 drive and the results are concluded in the last section.

This study examined how practice distribution schedules influenced accuracy and efficacy in the tennis serve. 24 recreational players were randomized into two experimental groups. Both groups carried out 4 series of 10 services per session during 12 sessions. Massed practice group did not rested between services and rested 10 seconds between series. Distributed practice group rested 10 seconds between services and 30 seconds between series. The accuracy and efficacy were registered and computed based on the 2D digitalization. The learning and retention were tested in a post-test and retention test. The learning program increased the efficacy in the post-test in both groups (p =.001 massed group; p =.015 distributed group). On the retest, the group of massed practice decreased efficacy (p =.021). In accuracy, the group of massed practice reduced its performance in the post-test (p =.015). The effects of the program on the accuracy in the retention test were not observed. It is concluded that this type of sports learning programs, applied at a recreational level, can provide a rigorous approach that contributes with guarantees to the learning of tennis.

In this paper, a modular wire-actuated robotic arm was designed to improve the safety and adaptability of service robots during human-robot interaction. To raise the stiffness adjustment range of the robotic arm, a symmetric variable-stiffness unit was designed based on flexure, which had compact and simple structure, and lowly nonlinear stiffness-force relationship. In this paper, we focused on the research of the symmetric 1-DOF joint module. Based on the kinematics and stiffness analysis, the pose of the joint module could be adjusted by controlling the length of the wires, and the stiffness of the joint module could be adjusted by controlling the tension of the wires. Because of the actuation redundancy, the pose and stiffness of the joint module could be controlled synchronously. Furthermore, a directly method was proposed for the stiffness-oriented wire tension distribution problem of the 1-DOF joint module. A simulation was carried out to verify the proposed method.

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

Genetic similarity determines the extent to which two genotypes share common genetic material. It can be measured in various ways, such as comparing DNA sequences, proteins, or other genetic markers. The significance of genetic similarity is multifaceted and encompasses various fields, including evolutionary biology, medicine, forensic science, animal and plant breeding, and anthropology. Genetic similarity is an important concept with wide application across different scientific disciplines. In the presented study, six measures for calculating genetic similarity were compared: Euclidean, Jaccard, Kulczyński, Sokal and Michener, Nei, and Rogers. The research material included 21 rapeseed genotypes (ten interspecific Brassicaceae hybrids of F2 generation, and 11 of their parental forms) and 146 alleles, obtained using 21 ISSR molecular markers. The results indicate that the research material was divided into two identical groups using any of the proposed methods, despite differences in the values of genetic similarity coefficients. Two of the presented measures of genetic similarity (Sokal and Michener, and Euclidean) were the same.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Long non-coding RNAs (lncRNAs) are involved in numerous biological processes and serve crucial regulatory functions in both animals and plants. Nevertheless, there is limited understanding of lncRNAs and their patterns of expression and roles in sharks. In the current study, we systematically identified and characterized lncRNAs in the blue shark Prionace glauca from four tissues (liver, spleen, muscle, and kidney) using high-throughput sequencing and bioinformatics tools. A total of 21,932 high confidence lncRNAs were identified with 8,984 and 3,067 stably and tissue-specific expressed lncRNAs, respectively. In addition, a total of 45,007 differentially expressed (DE) lncRNAs were obtained among tissues, with kidney versus muscle having the largest numbers across tissues. DE lncRNAs trans target protein-coding genes were predicted, and functional gene ontology enrichment of these genes showed GO terms such as muscle system processes, cellular/metabolic processes, and stress and immune responses, all of which correspond with the specific biological functions of each tissue analyzed. These results advance our knowledge of lncRNAs in sharks and present novel data on tissue-specific lncRNAs, providing key information to support future functional shark investigations.

: Schizophrenia and schizoaffective disorder are generally treated with second-generation antipsychotic drugs. These drugs are mostly D2 and 5-HT2A antagonists. They improve positive schizophrenia symptoms sufficiently well; however, they ameliorate negative schizophrenia symptoms and cognitive functions to a small extent. We review novel antipsychotic drugs exerting a partial agonism at dopaminergic and serotonergic receptors such as cariprazine, brexipiprazole and lumateperone. Besides, the mechanisms of actions of non-anti-dopaminergic antipsychotic drugs are pointed out. Updated neural networks are used to explain the mechanism of action of M4 and M1 receptor agonists, for example xanomeline combined with trospium or emraclidine, and trace-amine-associated receptor 1 agonists (TAAR1), for example ulataront. Phase 3 clinical trials of new third generation antipsychotic drugs are presented. Novel antipsychotic drugs with a partial agonism at D2 and D3 receptors improve positive and negative schizophrenia symptoms as well as cognitive symptoms better than second generation antipsychotic drugs. Besides, they are well tolerated. M4 and M1 receptor agonists, i.e. xanomeline combined with trospium or emraclidine, and TAAR1 agonists, i.e. ulataront, have promising results in clinical trials; they well improve negative schizophrenia symptoms and cognitive functions. Phase 3 clinical trials offer promising results for anti-dopaminergic and non-anti-dopaminergic novel antipsychotic drugs. These new non-anti-dopaminergic antipsychotic drugs better emend negative schizophrenia symptoms, and they better improve cognitive functions than second-generation antipsychotic drugs. Promising new antipsychotic drugs are cariprazine, brexipiprazole, lumateperone, ulataront, and xanomeline combined with trospium. Although phase 3 clinical studies are not yet completed, they showed a therapeutic effect superior to those achieved by second-generation antipsychotic drugs. They are tolerated very well, and they better treat negative schizophrenia symptoms and improve cognitive functions.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

This article titled "AI and IoT in Automation and Security: A Vision for Next Generation Applications," explored the implications of marrying IoT with AI in the realms of automation and security; this piece goes further into what that entails. In this paper, we present innovative application descriptions arising from this technology convergence and its future-generation applications. We found that AI brings strong cyber security, predictive maintenance, and decision-making capabilities to the table due to its advanced algorithms and machine learning models. IoT has the potential to allow businesses to extract and generate big data, automate processes, and monitor in real-time thousands and even millions of businesses at once. For now, we believe some of the possible main conclusions will be that the smart city, stand-alone systems, and user experience will be quite consumer-friendly. Importantly, the study also assessed facets such as data protection, system interoperability, and a few others. Our vision underscores the essential of a strong structure to connect the full latent of AI and IoT, finally aiming to create more capable, protected, and approachable environments. Significant results include achieving 95.8% accuracy in anomaly detection and 93.4% accuracy in predictive maintenance. The showcasing results efficacy of AI models to enhance system reliability as well as operational efficiency. Vigorous encryption protocols performance ensures data security hence addressing issues of privacy. These culminations underscore the transformative potential of AI-IoT integration in next-generation automation and security applications.

It’s very well known that the world's attention is currently focused on the energy transition. The energy security, in addition to the drive to reduce greenhouse gas emissions in order to limit global warming, and the generalization of the access to energy, have contributed to adoption of the Moroccan Energy Strategy with a strong focus on Renewable Energies (RE). Morocco is notoriously poor in conventional fossil primary energy resources with an energy dependence on the order of 90%. The energy crisis and that resulted from Covid-19 pandemic and the geopolitical conflicts, combined compounded with steady increase in demand have heavily affected the security and the stability of the country's energy situation. The transition to RE, by strongly engaging in the implementation of several solar, wind and hydro energy projects benefiting from the country's excellent solar and wind energy potential, has made the country the leader in RE in Africa. By 2030, the share of RE in the installed capacity is expected to reach 52%. In this work, an overview of the current situation of RE (particularly solar energy) in Morocco is provided, including, the potentials, obstacles and challenges, and future perspectives. Thanks to its high solar potential location, it’s predictable that Morocco effort will be focused on this field: the Erasmus Plus Innomed Project is a virtuous example of international cooperation, aiming at create a Solar Energy Network, in synergy with EU Partners.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

Objective: Interstitial fibrosis / tubular atrophy (IFTA) is a common, irreversible, and progressive form of chronic kidney allograft injury, and it is considered a critical predictor of kidney allograft outcomes. The extent of IFTA is estimated through a graft biopsy, while a non-invasive test is lacking. The aim of this study was to evaluate the feasibility and accuracy of an MRI radiomic-based machine learning (ML) algorithm in estimating the degree of IFTA in a cohort of transplanted patients. Approach: Patients who underwent MRI and renal biopsy within a 6-month interval from 1/1/2012 to 1/3/2021 were included. Stable MRI sequences were selected, and renal parenchyma, renal cortex and medulla were segmented. After image filtering and pre-processing, we computed radiomic features which were subsequently selected through a LASSO algorithm for their highest correlation with the outcome and lowest intercorrelation. Selected features and relevant patients’ clinical data were used to produce ML-algorithms using 70% of the study cases for feature selection, model training and validation with a 10-fold cross-validation, and 30% for model testing. Performances were evaluated using AUC with 95% confidence interval. Main results: 70 coupled tests (63 patients, 35.4% females, mean age 52.2 years) have been included and subdivided into a wider cohort of 50 for training and a smaller cohort of 20 for testing. For IFTA ≥ 25%, AUCs in test cohort were 0.60, 0.59, and 0.54 for radiomic features only, clinical variables only, and combined radiomic-clinical model, respectively. For IFTA ≥ 50%, AUCs in training cohort were 0.89, 0.84, 0.96, and in test cohort were 0.82, 0.83, and 0.86, for radiomic features only, clinical variables only, and combined radiomic-clinical model, respectively. Significance: An ML-based MRI radiomic algorithm showed promising discrimination capacity for IFTA>50%, especially when combined with clinical variables. These results need to be confirmed in larger cohorts.

The two combined technologies WPT and AI still have huge prospects for several industries such as consumer electronics and industry. This paper looks at the recent developments in WPT, particularly concerning AI-improved efficiency, range, and reliability. AI-driven also works to control power, manage device alignment, and test when maintenance is necessary, this makes powering smarter and more efficient. Accuracy is given by deploying machine learning and computer vision, and on the other hand, the maintenance procedure is done through predictions. Furthermore, the ability of the management system to include the use of AI in power regulation enables the control of consumption based on the load. In this study, the positive future effect of AI is discussed concerning improvements in WPT technologies, which is paramount in subsequent applications. Based on the results, it is essential to continue the investigation of the topic within this interdisciplinary science to advance existing problems and discover novel possibilities for evolution. Data based on experiments shows a significant improvement in the efficiency of information transfer where AI is used with rates up to 25% higher than those using the traditional ways. Additionally, advanced maintenance forecasting algorithms improve system availability by cutting down on 30% of the downtimes when applied in real-life applications of AI technology. The study also looks at the possibilities of the outlook to the future including emergence of the distributed artificial intelligence for autonomous WPT network, and additional potential of quantum computing for the use to improve the algorithm. This indicates that there is a new era for the convergence of WPT and AI to enhance the progress of power transfer system in conditions of elegant, efficient, and robust.

Background: The implementation of tyrosine kinase inhibitors (TKIs) in the treatment of chronic myeloid leukemia (CML) has brought a significant improvement in the prognosis for CML patients and a decrease in the number of patients requiring allogeneic hematopoietic stem cell transplantation (allo-HCT). Nevertheless, the impact of TKIs on allo-HCT outcomes have not been thoroughly explored. Objectives: The main endpoint of our research was to assess the impact of prior TKI treatment on acute graft-versus-host disease (aGvHD) and chronic graft-versus-host disease (cGvHD). Methods: In our retrospective analysis we included 240 patients treated between 1993 and 2013, and divided them into 3 groups according to the therapy administered prior to matched related or matched unrelated donor allo-HCT (imatinib group n=41, dasatinib/nilotinib group n=28, TKI naïve group n=171). Results: Both the cumulative incidence of aGvHD (p=0.044) and cGvHD (p&lt;0.001) in individuals receiving second generation TKIs (2G-TKIs) prior to allo-HCT compared to patients receiving no TKIs or imatinib (IMA) (40.7% vs 61.4% vs 70.7%, p=0.044; 25.0% vs 76.4% vs 51.2%, p&lt;0.001, respectively). In case of the 2G-TKI cohort, the number of low-grade aGvHD and cGvHD was significantly lower compared to the IMA and TKI-naïve groups (p=0.018, p=0.004; p&lt;0.001 versus TKI-naïve, respectively). In terms of 3-year overall survival (OS) there were no important variations between TKI-naïve, IMA and 2G-TKI (55% vs 49.9% vs 69.6%, p=0.740). Conclusions: The results of our study suggest that TKI treatment prior to allo-HCT may have protective impact on immune-mediated outcomes.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

This research explores a novel approach to integrating offshore wind farms into smart microgrids through the development of an advanced model predictive control (MPC) strategy for offshore wind turbines. The MPC strategy comprehensively incorporates complex wind dynamics, such as wind speed, direction, and turbulence, ensuring an accurate representation of turbine behavior. Additionally, the research includes models addressing wind farm layout, wake effects, and electrical infrastructure, enhancing the modeling framework's fidelity and applicability to real-world offshore wind energy systems within a smart microgrid environment. The inherent variability of wind power, transmission technology limitations, and the need for seamless transitions between grid-connected and islanded operation modes in smart microgrids necessitate robust control mechanisms. These mechanisms ensure efficient power capture, grid stability, and optimal energy utilization. To tackle these challenges, the research proposes a smart microgrid design incorporating both AC-DC and DC-DC conversion technologies. This design leverages renewable energy sources like solar and wind with AC-DC conversion for efficient power capture, integrates DC energy storage systems to store excess energy during low demand periods, and utilizes power control mechanisms to manage energy flow effectively within the smart microgrid. The study emphasizes the importance of modeling and control strategies for both AC-DC and DC-DC converters within the smart microgrid framework. To enhance the microgrid's cost-effectiveness, priority is given to the utilization of solar PV energy sources. It also highlights the integration of protection systems for DC faults and coordinated control of AC/DC breakers and converters. This comprehensive approach aligns with the core principles of adaptability, reliability, and sustainability in smart grids, aiming to advance smart microgrid technologies and pave the way for a more resilient, efficient, and secure energy future.

In this paper, a recent meta-heuristic optimization algorithm called the discrete-continuous hyper-spherical search algorithm is used to solve the mixed-integer nonlinear problem of soft open points (SOPs) and renewable distributed generators allocation along with new network reconfiguration methodology under different loading conditions to minimize the total power loss in balanced distribution systems. Multi-scenario studies, which aim to improve the investigation of the overall performance of the strategies, are conducted on IEEE 33-node and 83-node balanced distribution systems. The contributions of SOP losses to the total active losses, as well as the effect of increasing the number of SOPs connected to the system, are investigated to determine the real benefits gained from their allocation. The results obtained validate, with proper justifications, the effectiveness of allocating both SOPs and renewable distributed generators with the proposed network reconfiguration methodology to provide the best operation of distribution networks with minimum losses and enhanced power quality performance. It was also shown that SOPs successfully assist the growing integration plans of the renewable distributed generators units and can address issues related to voltage violations and network losses efficiently.

We present a review of the current state of the field for a rapidly evolving group of technologies related to solar energy harvesting in built environments. In particular, we focus on recent achievements in enabling the widespread distributed generation of electric energy assisted by energy capture in semi-transparent or even optically clear glazing systems and building wall areas. Whilst concentrating on the cutting-edge recent results achieved in the integration of traditional photovoltaic device types into novel concentrator-type windows and glazings, we compare the main performance characteristics reported with these achievable using more conventional (opaque or semi-transparent) solar cell technologies. A critical overview of the current status and future application potential of multiple existing and emergent energy harvesting technologies for building integration is provided.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

Segregating one space from another is a rudimentary act of architecture and the basic principle of this act is creating differentiation between outside and inside. Thresholds, in their expanded or summed form, also produce spaces. They establish the staging for threshold areas in conjunction with space-defining elements. Threshold spaces are typically complicated spatial formations that serve as transition points. They pose a challenge to the interacting human senses in terms of perception. In this research threshold areas have been studied under a specific typology of architecture i.e the traditional housing in historic cities of India. The traditional dwelling settlements have evolved and grown over multiple layers of history, influenced by the culture, society, economy, climate and topography. The purpose of this research is to examine the characteristics of these transition spaces of the traditional dwelling units in relation to the symbolic reference and social meanings assigned to them that influence the architectural and urban spaces attached to them. It seeks to describe transition space in terms of its nature, character, morphology, and social significance. Transparency and material articulation, as well as hierarchy and enclosure, will be investigated. The importance and quality of the nature of "transition" will be examined from the inside to the outside. The research reveals that the space has great functional and socio-cultural importance. It allows multiple activities, provides protection from sun and rain, defines boundaries, connects people within the neighborhood, enhances security and gives an identity to the owner. The contributions made by this research have the potential to improve design considerations for transition areas between the dwelling units and the street.

Puerto Rico's geographic and climatic conditions render it highly susceptible to natural disasters, particularly hurricanes. The devastation caused by Hurricane Maria in 2017 highlighted the fragility of the island's centralized energy infrastructure, which led to prolonged power outages and severe disruptions in essential services. This review explores the potential of biomass energy to enhance resilience in post-disaster scenarios, focusing on Puerto Rico as a case study. Biomass energy, derived from organic materials like agricultural residues, woody biomass, and municipal solid waste, offers a renewable and locally sourced power solution that can be rapidly deployed. Key biomass conversion technologies, including direct combustion, gasification, anaerobic digestion, and pyrolysis, are examined for their applicability and benefits in emergency energy provision. The implementation of biomass-powered microgrids in Puerto Rico, such as those by Casa Pueblo and Arensis, demonstrates the feasibility and effectiveness of decentralized energy systems in disaster recovery. These microgrids provide reliable power to critical infrastructure, reduce dependence on fossil fuels, and support waste management efforts. The review also discusses ongoing research and development in advanced biomass technologies, such as second-generation biofuels, algae-based biomass, and biomass-to-hydrogen conversion, which can further enhance energy efficiency and sustainability. Additionally, the economic, environmental, and social impacts of biomass energy are evaluated, highlighting its role in job creation, waste reduction, emission control, and community resilience. Policy recommendations include streamlining permitting processes, enhancing financial incentives, developing feedstock supply chains, and incorporating biomass into disaster recovery plans. The findings suggest that integrating biomass energy into Puerto Rico’s energy strategy can significantly improve its capacity to respond to and recover from natural disasters, promoting long-term sustainability and resilience.

Four-wire low voltage microgrids supply one-phase consumers with continuously changing electricity demand. For addressing climate change concerns, governments implemented incentive schemes for residential consumers, encouraging the installation of home PV panels for covering self-consumption needs. In the absence of sufficient storage capacities, the surplus is sold back by these entities, called prosumers, to the grid operator or in local markets, to other consumers. While these initiatives encourage the proliferation of green energy resources, and ample research is dedicated to local market designs for prosumer-consumer trading, the main concern of distribution network operators is the influence of power flows generated by prosumer surplus injection on the operating states of microgrids. The change in power flow amount and direction can greatly influence the economic and technical operating conditions of radial grids. This paper proposes a metaheuristic algorithm for prosumer surplus management that optimizes the power surplus injections using the automated control of three-phase inverters, with the aim of improving the active power losses and balancing the phase voltage profiles. A case study is performed on two real distribution networks with distinct layouts and load profiles and the algorithm shows its efficiency in both scenarios.

- Power grids of the future will likely incorporate more renewable energy distributed generation (REDG), also known as alternative energy systems. REDG units are increasingly being used in electrical transmission networks because to the overall positive effects they have on power networks. REDG systems are the backbone of smart electric networks and are essential to the operation of the smart grid. These REDG systems can additionally improve system reliability by providing some customers with a backup generator in the event of power interruptions. The report offers a thorough evaluation of the existing body of information on the topic of electric vehicles' (EVs') future interactions with the smart grid. The combination of the EVs' potential deployment and the smart grid's conceptual goal presents challenges in electric grid infra-structure, communication, and control. The proposal for connecting EVs to the grid is based on research into cutting-edge smart metering and communication systems. In the context of the vehicle-to-grid (V2G) phenomenon, the possibilities, benefits, and limitations of various EV smart charging systems are also fully examined. There is a fast growing percentage of distributed energy that is wind and solar photovoltaic. Their variable power output, however, introduces fresh challenges for those responsible for organizing, operating, and controlling the power grid. While fluctuations in the electric grid are problematic, they may be mitigated by the entry of EVs into the energy market. As such, we do a comprehensive literature search to learn more about the exciting research gap that needs to be filled and the most recent possible answer that involves EVs. Additionally, we take a close look at the practicality of the sophisticated V2G technology. The smart grid is a developing concept for the world's energy infrastructure, and this study analyzes in depth how EVs interact with it.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

The application of non-uniform spiral gratings to control structure, topological parameters and propagation of orbital angular momentum (OAM) beams was studied experimentally with coherent near-infrared light. Adapted digital spiral grating structures were programmed into the phase map of a high-resolution liquid-crystal-on-silicon spatial light modulator (LCoS-SLM). It is shown that characteristic spatio-spectral anomalies related to Gouy phase shift can be used as pointers to quantify rotational beam properties. Depending on sign and gradient of spatially variable periods of chirped spiral gratings (CSG), variations of rotation angle and angular velocity as a function of propagation distance were measured. Propagation-dependent self-torque is introduced in analogy to known local self-torque phenomena of OAM beams as obtained by the superposition of temporally chirped or phase modulated wavepackets.

The increasing expansion of the use of renewable distributed generation (RDG) technologies in electrical networks such as solar plants or wind farms and others has changed the nature of the distributed system and transformed it from the traditional system into an efficient system. This system has led to various technical effects in the host networks, with regard to voltage, electrical energy losses, fault levels, stability and electrical energy quality. These effects are not generic to any network; It can be positive, negative or neutral depending on the structure of the studied network, its operational condition and the various technology of the distributed generators. This research aims to quantitatively correct the effects of (RDG) in terms of voltage and electrical energy losses in the host networks. , since efficient distribution systems contain generators of a special nature and often contain bidirectional flux energy, it was necessary to construct a mathematical model of the distribution system hosting RDG units, which is fundamentally different from the traditional model of defining the reference electrical distribution bus bar. In order to achieve the systematic analysis, evaluation criteria and indicators were determined and mathematical formulas for them were completed. Based on the accomplished mathematical basis, an algorithm designed in such a way that it can be applied to any multi-voltage distribution system and to different distributed regenerative generation techniques is proposed. To demonstrate the algorithm's capabilities, it was tested on typical distribution networks using Factory Power DigSilent software, which is somewhat similar to MATLAB but more suitable for large capacity systems.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

The integration of the Internet of Things (IoT) and Distributed Computer Systems (DCS) is transforming business models across industries. IoT devices enable real-time monitoring of equipment and processes, reducing downtime and enhancing efficiency. In the case, manufacturing companies use IoT sensors to monitor machinery, predict failures, and schedule maintenance. Also, automation via IoT, reduces manual intervention, resulting in boosted productivity in smart factories and automated supply chains. IoT devices generate thus vast amounts of data, which businesses analyze to gain insights into customer behavior, operational inefficiencies, and market trends. In turn, distributed computer systems process this data, providing actionable insights and enabling advanced analytics and machine learning for future trend predictions. While, IoT facilitates personalized products and services by collecting data on customer preferences and usage patterns, enhancing satisfaction and loyalty, IoT devices support new customer interactions, like wearable health devices, and enable subscription-based and pay-per-use models in transportation and utilities. Conversely, real-time monitoring enhances security, as distributed systems quickly respond to threats, ensuring operational safety. It also aids regulatory compliance by providing accurate operational data. In this way, this study, through a Bibliometric Literature Review (LRSB) of 91 screened pieces of literature, aims at ascertaining to what extent the aforementioned capacities enhance business models. The study concludes that those systems leverage businesses, promoting competitive edge, continuous innovation, and adaptability to market dynamics. A review of 91 academic documents from the Scopus database highlights these impacts.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&amp;O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&amp;O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

Orodispersible film (ODF) is one of the novel formulations that have been currently made available that disintegrates rapidly in the mouth without the requisite for water and offer several benefits over conventional oral solid dosage formulations. This delivery system serves as a discreet and convenient mode of administration, especially in patients who have dysphagia, fluid restriction, being beneficial to pediatric, geriatric, and bedridden patients. A novel sildenafil ODF containing sildenafil citrate is formulated to be used in patients with erectile dysfunction (ED). This review discusses the advantages of ODF in improving compliance and satisfaction in these patients and describes the bioequivalence and stability studies of sildenafil ODF. This formulation offers unique benefit to patients with ED by improving their acceptance, compliance, and respecting their privacy. Moreover, the comparison of pharmacokinetic parameters between the sildenafil ODF administered with and without water and the conventional film-coated tablet were similar. It also demonstrated reliable performance that yielded a consistent product, meeting all specifications at release and after three weeks of storage under stressed conditions (60oC). Sildenafil ODF warrants improved ease of intake, taste, portability, storage, and compliance among ED patients, making it the potential most preferred formulation and drug of choice.

The use of Retrieval-augmented generation (RAG) using large language models (LLMs) has shown potential for addressing issues such as hallucinations and inadequately contextualized responses. A pivotal stage in the RAG process involves a retriever for retrieving chunks based on semantic similarity with the query. In this study, we advocate for and provide experimental evidence supporting integrating and maintaining questions and answers (QA) formatted databases to improve retrieved-context representations and response quality. Our experiments evaluate our approach on benchmark RAG datasets using standard evaluation metrics and provide comparative analyses against state-of-the-art retrieval methods, showing the potential of our approach.

Background/Objectives: Community-acquired pneumonia (CAP) is a common emergency presentation in Australia, with the choice of admitting specialty unit often influenced by pneumonia severity and comorbidities. However, it remains unclear whether there are between-specialty differences in patient characteristics and outcomes. We sought to address this issue by investigating the characteristics and outcomes of CAP patients admitted to General Medicine (GM) versus Respiratory units.Methods: This retrospective observational study utilised data from the two largest metropolitan hospitals in South Australia, encompassing all non-COVID-19-related CAP admissions throughout 2021 to 2023. Hospital length of stay (LOS), in-patient and 30-day mortality, and 30-day readmission rates were assessed by propensity-score-matching (PSM) with using 14 variables.Results: Of the 3,004 cases of non-COVID-19 CAP admitted across the two hospitals during the study period, 2,673 (71.8%) were admitted under GM units and 331 (9.1%) under Respiratory units. GM patients were, on average, a decade older, presented with a significantly higher burden of comorbidities, exhibited a greater prevalence of frailty and had higher pneumonia severity compared to those admitted under a Respiratory unit, (P

In the scientific community, it is difficult to find a consensus on defining BIM. Just as the acronym BIM is developed in different ways, it is also understood in different ways. Depending on its understanding, different definitions emerge. It is defined differently by organizations and standards, still differently by academics. Many years of academic discourse on the subject have failed to produce a solution. Despite the fact that the acronym BIM has already done its work for the construction industry, it still stirs up excitement. There is still no clear definition, as the view of BIM varies from one perspective to another. This article attempts to sort out the definitions cited so far by important organizations and key academics. The review was based on deep literature study has attempted to be inclusive and consistent. The question still remains open: do we need a single, correct definition of BIM? The aim of the article is to try to answer this question, open up a renewed discussion and come to a satisfactory consensus. BIM can be identified with an activity, product or system. The article breaks down the definitions of BIM, identifies six key attributes of BIM, presents the evolution of the understanding of BIM and proposes new definitions in a narrow and broad approach.

There is an increasing need for quantitative rockfall hazard and risk assessment that requires a precise definition of the terms and concepts used for this particular type of landslide. This paper suggests to use terms that appear to be the more logic and explicit as possible, and describes methods to derive some of the main hazard and risk descriptors. The terms and concepts presented concern the rockfall process (failure, propagation, fragmentation, modelling) and the hazard and risk descriptors, distinguishing the cases of localized hazards and diffused hazards. For a localized hazard, the failure probability of the considered rock compartment in a given period of time has to be assessed and the probability for a given element at risk to be impacted with a given energy must be derived combining the failure probability, the propagation probability and the exposure of the element. For a diffuse hazard that is characterized by a failure frequency, the number of rockfalls reaching the element at risk per unit of time and with a given energy (reach frequency) can be derived. However, when the element at risk is not replaced or repaired, the probability that it is impacted by at least one rockfall must be considered.

This study explores the potential to reach a circular economy for post-consumer recycled polyethylene terephthalate (rPET) packaging and bottles by using it as a distributed recycling for additive manufacturing (DRAM) feedstock. Specifically, rPET is processed using only an open source toolchain with fused particle fabrication (FPF) or fused granular fabrication (FGF) processing. In this study, first the impact of granulation, sifting and heating (and their combination) is quantified on the shape and size distribution of the rPET flakes. Then feeding studies were performed to see if they could be printed through an external feeder or needed to be direct printed with a hopper using two Gigabot X machines, one with extended part cooling and one without. Print settings were optimized based on thermal characterization and for the latter which was shown to print rPET directly from shredded water bottles mechanical testing is performed. The results showed that geometry was important for extended feeding tubes and direct printed using a hopper. Further there is a wide disparity in the physical properties of rPET from water bottles depending on source and the history of the material. Future work is needed to enable water bottles to be used as a widespread DRAM feedstock.

Following an updated outlook of global energy production and utilization, we show through selected examples from both developing and developed countries how distributed generation from renewable energy sources, and from solar energy in particular, is the key solution to ending energy poverty across the world. Guidelines aimed at policy makers suggest a systems view of energy that will be instrumental in guiding the transition from fossil fuels to combustion-free renewable energy for all energy end uses.

In recent years, distributed generation technology has developed rapidly. Renewable energy, represented by wind energy and solar energy, has been widely studied and utilized. In order to give full play to the advantages of Distributed Generation (DG) and meet the challenges after power grid access, Active Distribution Network (ADN) is considered as the future development direction of traditional distribution network because of its ability of active management. Nowadays, multi-scenario analysis is widely used in the research of optimal allocation of distributed power supply in active distribution network. Aiming at the problems that may arise when using multi-scenario analysis to plan DG with uncertainties in large-scale scenarios, a scenario reduction method based on improved clustering algorithm is proposed. The validity of the scene reduction method is tested, and the feasibility of the method is verified. At present, there are few studies on the optimal allocation of DG in ADN under fault state. In this paper, comprehensive safety indicators are introduced. Considering the timing characteristics of DG and the influence of active management mode, a bi-level programming model is established, which aims at minimizing the investment of annual life cycle and the removal of active power. The bi-level model is a complex mixed integer non-linear programming model. A hybrid algorithm combining cuckoo search algorithm and primal dual interior point method is used to solve the model. Finally, through the simulation of the IEEE-33 node system, the superiority of the scenario reduction method and the comprehensive security index used in this paper to optimize the configuration of DG in ADN is verified.

This proposal advocates using energy states as fundamental units for quantum computer programming. Each programming unit is conceptualized as an energy state, manifested as an essence-unit. The essence-unit, defined as the minimal form encapsulating complete uniqueness or specificity, serves as the cornerstone of this paradigm. This approach allows recording various forms of matter on quantum computers in essence-units representing their energy states. Recording energy states is achieved through the creation of four distinct coherent potentials facilitated by quantum dots or crystals. It is crucial to note that these energy states, embodied in essence-units, cannot be subdivided. The study examines the intricate relationship between similarity, fractals, and uniqueness in quantum dot operations, elucidating their profound implications for information transfer efficiency. Normalized entropy quantifies the charge localization in quantum dot impurities in systems exhibiting distortions. Utilizing N-level recording and entropy-fractal dimension equivalence enables this paper to elucidate the potential of quantum dots in reducing transmission time and modeling complex systems. The proposed methodology represents a significant departure from the current state of quantum computing, offering unprecedented potential for overcoming previously intractable challenges.