This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Successful geophysical exploration works in Gucheng-Yaxi area located in Gaochun District, Jiangsu province, China, have been limited partly due to complex geological condition of the area and high artificial noise in data acquired using electrical and electromagnetic methods. In this work, we deployed the new anti-interference spread spectrum induced polarization method (SSIP) and audio magnetotellurics (AMT) method to detect a copper-polymetallic deposit in the area. Two-dimensional (2D) inversion results at Gucheng-Yaxi Area revealed a high chargeability anomalous zone on SSIP profile that coincided with a zone of moderate resistivity located between two resistor bodies on AMT profile. A follow up 1200 meters drill hole was established at this high chargeability-moderate resistivity zone which encountered polymetallic (copper, lead, zinc, gold and silver) mineralization at the depth ≥ 400 m. Drill hole data analysis showed that mineralization occurs interspaced in marble rock mass at varies depth. Furthermore, several low resistivity-weak chargeability sections were revealed and inferred attributed to Cretaceous sediments and faults. These faults are thought to have played critical role in the polymetallic mineralization genesis. In summary, this work demonstrated the successful of application of SSIP and AMT at detecting a metallic deposit in an area with high artificial noise. Hence the geophysical prospection potential of Gucheng-Yaxi area is great.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

Models of subsurface structures are important for successful deposit exploration but are challenged by the need to integrate data from different geophysical methods. In the present study, we evaluated a method of joint inversion in which audio-magnetotelluric (AMT) and dual frequency induced polarization (DFIP) data sets are inverted simultaneously to produce a consistent 2D resistivity model to show a clear image of subsurface structures. To achieve the objectives, we conducted AMT and DFIP surveys first on the same survey line within the Dongjun lead-zinc deposit in inner Mongolia by developing 31 AMT survey sites with an interstation separation of 40 m on a 1440 m survey track and operated in fifty-three frequencies in the range 1–10,400 Hz to record the resistivity distribution of subsurface to depths exceeding 800 m. The same survey setup up was applied to the DFIP method by utilizing the SQ-3C model with a pole-dipole array configuration and conducted measurements at frequencies of 4 Hz and 4/13 Hz. We first separately inverted AMT and DFIP measurements. The two-dimensional (2D) model obtained from AMT data revealed distinct low resistivity anomalies in the middle of the 2D inversion model. In contrast, the DFIP inversion model showed a high resistive body in the same region. In response to the discrepancies observed in the separate 2D inversion models, we implemented a joint inversion for both the AMT and DFIP datasets. The joint inversion resistivity model shows surficial conducting bodies and a high conductive body along the profile with relatively high Percent Frequency Effect (PEF) indicating high chargeability. The final joint inversion resistivity model clearly images the large silica alteration zone and the Pb-Zn mineralization. This study demonstrates the feasibility of a joint inversion methodology and highlights the value of integrating geophysical methods through joint inversion for enhanced characterization and exploration of lead-zinc ores.

The Shimensi super-large tungsten polymetallic deposit is located in Late Jurassic- Early Cretaceous Porphyry-Skarn tungsten ore belt in the south Yangtze metallogenic belt. There are 3 types of mineralization: veinlet-disseminated type, thick quartze vein type and hydrothermal crypto-explosive breccia type. Based on geological studies, this paper presents new petrographic, microthermometric, laser Raman spectroscopic and hydrogen and oxygen isotope research of the fluid inclusions from the deposit. The results show that there are five different types of fluid inclusions: liquid-rich inclusions, vapor-rich inclusions, pure liquid inclusions, pure vapor inclusions, and fluid inclusions containing a solid crystal. The homogenization temperatures of the fluid inclusion range from 140℃-270℃, the salinities are 3%-5% NaCleq and the densities of ore-forming fluid range from 0.64 g/cm3 to 0.99 g/cm3. For the analyses of Laser Raman spectroscopic, the ore-forming fluids can be approximated by a Ca2+-Na+-SO42--Cl- fluid system with small amount of CO2, CH4 and N2. Otherwise, the datas of the pressure, pH and Eh show a fluid metallogenic environment of low pressure, weak acid and weak reduction. The values of the homogenization temperature in 3 types of orebodies suggest that the mineralization is characterized by the decrease of the temperature under the condition of the fluid immiscibility. The H-O isotope values are interpreted to indicate that the ore-forming fluids are mainly composed of magmatic water, and also the meteoric water was added with the process of the magma rising.

An increased demand for natural products nowadays most specifically probiotics (PRO) is evident since it comes in conjunction with beneficial health effects for the consumers. In this regard, it is well known that encapsulation could affect positively the PRO's viability throughout food manufacturing and long-term storage. This paper aims to analyze and review various multilayer strategies for encapsulation of PRO. Double-layer encapsulation of PRO by electro-hydrodynamic atomization or electrospray technology has been reported along with layer-by-layer assembly and water-in-oil-in-water (W1/O/W2) double emulsions to produce multilayer PRO-loaded carriers. Finally, their applications in food products are presented. The resistance (cover material) and viability of (PRO) to mechanical damage, during gastrointestinal transit and shelf life of these trapping systems are also described. The PRO encapsulation in double and multiple-layer coatings combined with other technologies can be examined to increase the opportunities for new functional products with amended functionalities opening a novel horizon in food technology.

Spin Assisted Layer-by-Layer (SA-LbL) assembly is one of the Layer-by-Layer (LbL) assembly variants. It is considered as the fastest LbL assembly, however, the deficiency of layering quality on bigger polymeric support size poses a significant challenge to the application of SA-LbL assembly at a larger or industrial scale. To address the challenge, combined spin-spray assisted Layer-by-Layer (SSA-LbL) is employed to prepare membrane. In this study, nanofiltration (NF) thin film composite membranes were prepared by alternate deposition of branched-polyethyleneimine (PEI) and poly(sodium 4-styrenesulfonate) (PSS) on polyethersulfone (PES) ultrafiltration (UF) membrane support. The resulting membrane was then tested to separate NaCl from water. One of the membranes produced in this work, i.e., (PEI/PSS)10 achieved rejection rate of 76.2 %; permeability of 2.79 l/h·m2·bar tested at pressure of 10 bar, temperature of 24.58 ± 0.51 °C , and NaCl-Feed concentration of 2076.75 ± 40.51 ppm. The membrane fouling resistance was also examined in 5 days-test. The membrane showed stable performance and lost only about 30% flux from the initial flux due to fouling which was comparable to that of commercial NF membrane such as NF90. Hence, this work shows that SSA-LbL can be considered as a promising and innovative membrane fabrication technique as it offers flexibility and applicability for preparing membrane from various materials as well as pertinence to industrial scale.

Spatial crowdsourcing emerges as a new computing paradigm that enables mobile users to accomplish spatio- temporal tasks in order to solve human-intrinsic problems. Existing crowdsourcing systems critically use centralized servers for interacting with workers and making task assignment decisions. These systems are hence susceptible to issues such as the single point of failure and the lack of operational transparency. Prior work, therefore, turns to blockchain-based decentralized crowdsourcing systems, yet still suffers from problems of lacking efficient task assignment scheme, requiring a deposit to an untrusted system, low block generation speed, and high transaction fees. To address these issues, we design a blockchain-based decentralized framework for spatial crowdsourcing, which we call SC-EOS. Our system does not rely on any trusted servers, while providing efficient and user-customizable task assignment, low monetary cost, and fast block generation. More importantly, it frees users from making a deposit into an untrusted system. Our framework can also be extended and applied to generic crowdsourcing systems. We implemented the proposed system on the EOS blockchain. Trace-driven evaluations involving real users show that our system attains the comparable task assignment performance against a clairvoyant scheme. It also achieves 10× cost savings than an Ethereum-based implementation.

We have studied quality characteristics, chemical, mineral and isotope composition of nephrite, diopsidite and rodingite of the Nyrdvomenshor deposit in the Polar Urals. We applied the visual petrographic and mineralogical studies, X-ray spectral fluorescence, ICP-MS analysis, scanning electron microscope with the dispersive microanalysis system, oxygen isotope composition was measured. According to its quality characteristics, the nephrite is substandard. Here, uvarovite, which forms idiomorphic grains, sometimes sheath-like, less often xenomorphic elongated, and substituting chromite are commonly encountered. The nephrite was formed due to both metamorphic and metasomatic processes. Serpentinite was replaced by diopsidite, which was then replaced by nephrite. Metamorphism intensified metasomatism of the serpentinite melange and provided a cryptocrystalline tangled-fibrous structure of the nephrite. Then metamorphism and metasomatism led to the formation of omphacite and cracking of the nephrite, which reduced its quality. As these processes progressed, contribution of crustal fluid increased.

Recent advances in signal processing and AI-based inference enable the exploitation of communication signals to collect information on devices, people, actions and the environment in general, i.e., to perform Integrated Sensing And Communication (ISAC). This possibility opens new and exciting opportunities for IoT systems, but at the same time poses unprecedented threats to security and privacy of data, devices, and systems. In fact, ISAC operates at the PHY and Medium Access Control (MAC) layers, where it is impossible to protect the information with standard encryption techniques, or with any other purely digital methodologies. The work we present analyzes, within the framework of IoT and distributed, pervasive communication systems, the threats to security and privacy posed by ISAC and how they do intertwine at the PHY layer. Next, possible countermeasures are presented and discussed, with proper architectural choices and tradeoffs to implement them, as well as solutions and protocols to preserve the potential benefits of ISAC while ensuring data protection and users’ privacy.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

Modification of electrode surface with a selective layer gives the possibility to detect target ana-lytes of forensic interest. 3-(4-trifluoromethyl)-phenyl)-thiophene (ThPhCF3) was deposited on a graphite (G) electrode by electrochemical oxidation and characterized as a receptor for the recognition of synthetic stimulants (2-aminoindane, buphedrone, naphyrone). First, the structural characterization of the polymeric layer were obtained from Raman spectroscopy. Second, the electrochemical profiles of selected synthetic stimulants and their affinity to ThPhCF3/G-modified electrodes were studied using square wave voltammetry and electrochemical impedance spec-troscopy. The values of the adsorption constant show the importance of – PhCF3 groups in the interaction with synthetic stimulants, namely recognition by the formation of hydrogen bonds (Kads (buphedrone) < Kads (2-AI)) and interaction with aromatic H atoms (Kads (buphedrone) < Kads (naphyrone)). It was demonstrated that the polymeric layer derived from thiophene with – PhCF3 group is capable to increase the intensity of the electrochemical signal.

Banks are normally offered two kinds of deposit accounts. It consists of deposits like current/saving account and term deposits like fixed or recurring deposits. For enhancing the maximized profit from bank as well as customer perspective, term deposit can accelerate uplifting of finance fields. This paper focuses on likelihood of term deposit subscription taken by the customers. Bank campaign efforts and customer detail analysis can influence term deposit subscription chances. An automated system is approached in this paper that works towards prediction of term deposit investment possibilities in advance. This paper proposes deep learning based hybrid model that stacks Convolutional layers and Recurrent Neural Network (RNN) layers as predictive model. For RNN, Gated Recurrent Unit (GRU) is employed. The proposed predictive model is later compared with other benchmark classifiers such as k-Nearest Neighbor (k-NN), Decision tree classifier (DT), and Multi-layer perceptron classifier (MLP). Experimental study concludes that proposed model attains an accuracy of 89.59% and MSE of 0.1041 which outperform well other baseline models.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

In recent years, intelligent identification and prediction of ore deposits based on deep learning algorithm and image processing technology has gradually become one of the research frontiers in the field of geological and metallogenic prediction. However, this method also has many problems that need to be solved. For example, (1) very few trainable image samples containing mineral point labels; (2) The geological image features are small and irregular, and the image similarity is high; (3) It is difficult to calculate the influence of different geological prospecting factors on ore mineralization. Based on this, this paper constructs a deep learning network model Multiscale Feature Attention Framework (MFAF) based on geo-image data. The results show that MFCA-Net module in MFAF model can solve the problem of scarce mine label images to a certain extent. In addition, the channel attention mechanism SE-Net module can quantify the difference of influence of different source factors on mineralization. The prediction map is obtained by applying the MFAF model in the study of deposit identification and prediction in the research area of the southern section of Qin-hang metallogenic Belt. In the forecast map, many regions have high metallogenic potential. Through observation, it is found that the above predicted area covers 100% of the known ore deposits at present, which has a good prediction effect. Later, we can find out the specific reasons through field verification. The multi-scale feature fusion and attention mechanism MFA Framework in this paper can provide a new way of thinking for geologists in mineral exploration. The research of this paper also provides resource guarantee and technical support for the sustainable exploitation of mineral resources and the sustainable growth of society and economy.

Marine clay deposits are commonly found worldwide. Considering the cost of dumping and the related environmental concerns, an alternative solution involving the reuse of soils that have poor conditions is crucial. In this research, the authors examined the durability of marine deposited clays and compiled a corresponding database. The use of slag alone as a binder, at any percentage, increased the accumulated mass loss (ALM) up to 2%. However, the use of lime as the third binder seemed to accelerate the chemical reactions associated with the hydration of clay and cementitious material and to enhance the chemical stability, i.e., samples that included both lime and slag experienced the same ALM as samples treated with cement only. Scanning electron microscopy analysis confirmed the durability improvements of these clays. The proposed unconfined compressive strength and accumulated mass loss relationship yielded practical approximation for the fine- and coarse-grained soils blended with up to three binders until 60 days of curing.

Delaying the onset of laminar-turbulent transition is an attractive method in reducing skin friction drag, especially on streamlined bodies where Tollmien-Schlichting instabilities are the dominating mechanism for transition. Miniature vortex generators (MVGs) offer an effective approach to attenuate these instabilities by generating counter-rotating vortex pairs. They are placed in pairs within an array and resemble small winglet-type elements. The conventional methodology involves adjusting MVG parameters and conducting computationally expensive DNS and/or downstream stability analyses to assess their effectiveness. However, analyzing the vortex parameters of MVG-generated vortices can potentially guide a more targeted approach in modifying MVG parameters and identifying critical factors for transition delay. Therefore, this study investigates changes in three primary MVG parameters, namely inner distance, periodicity and height, and utilizes computational fluid dynamics (CFD) analysis to create a dataset that examines the characteristics of the generated counter-rotating vortex pairs and their potential in drag reduction. The objective is to establish correlations among these parameters and their influence on delaying transition.

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

The Huaniushan lead-zinc-silver deposit is a hydrothermal sedimentary exhalative deposit (SEDEX). The mining area has complex geological conditions. The main tectonic structure in the area is the Huaheitan-Shuangfengshan Fault (F3), which controls the distribution of strata and magmatic rocks. Since the discovery of the Huaniushan Lead-zinc-silver polymetallic deposit, there are diverse understandings of the deposit's genesis and mineralization law, making it challenging to meet the geological interpretation requirements of the Huaniushan Lead-zinc-silver polymetallic deposit. Moreover, a single geophysical exploration method utilizes limited rock physical parameters, making it difficult to effectively characterize underground structures. The integrated exploration of multiple geophysical methods can effectively integrate the geophysical characteristics of different rock physical parameters, reducing the multiplicity and uncertainty of geophysical data inverse interpretation. The comprehensive interpretation of three-dimensional inversion based on various geophysical data, the construction of geological-geophysical models based on geological grounds, the establishment of hidden ore exploration and positioning, and the rapid evaluation of geophysical technology systems are the current development trends in mineral exploration. In light of this, this paper conducts research on the three-dimensional inversion interpretation of the heavy magnetoelectric exploration data of the Huaniushan sedimentary exhalative deposit lead-zinc-silver polymetallic deposit in the mining area and constructs a three-dimensional geological-geophysical model of the study area based on the obtained three-dimensional physical structure of the underground three-dimensional density, magnetization intensity, resistivity, and polarizability structure of the study area, in combination with the information of related geology and drilling holes. It comprehensively interprets the favorable mineralization parts in the study area.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

The Ballynoe barite deposit is a conformable, mineralized horizon of Lower Carboniferous age overlying a diastem and mass faunal extinction demarking the transition from a quiet water environment to one of dynamic sedimentation. The geometry of the barite orebody correlates with the palaeo-topography of the footwall, which acted as an important control over the lateral extent, thickness and nature of the mineralization. Sedimentary features within the barite horizon suggest that it was precipitated in the form of a cryptocrystalline mud which underwent major diagenetic modification resulting in extensive stylolitisation, recrystallisation and remobilization. There is abundant and compelling geological and isotopic evidence for early local exhalation from the presence of a hydrothermal vent fauna consisting of a delicately pyritized worm tubes hosted and haematized filaments of apparent microbial origin. The worm tubes are remarkably similar to examples from modern and ancient volcanic-hosted massive sulphide deposits, and the filamentous microfossils have similarities to modern Fe-oxidizing bacteria. Strontium in the barite has a 87Sr/86Sr ratio indistinguishable from sea-water between 350 and 344Ma whilst oxygen isotopes from barite and chert suggest a diagenetic origin in equilibrium such sea-water around 60-70°C. Fluid inclusion studies have shown that, in general, low temperature inclusions are very saline (20-25%) whilst at higher homogenization temperatures they are more dilute (9-12%).

Allanite minerals are the principal host of REEs in the Sin Quyen, Iron Oxide Copper Gold (IOCG) type deposit. The studied allanites have concentrations of: REE (14-27 wt%), Ca (9-16 wt%), Al (8-19 wt%), Si (26-34 wt%) and Fe (12-21 wt%). Two populations of allanite are documented, the first is texturally older probably related to the Ca-K alteration (second stage of crystallization). This population has higher REE concentrations ranging from 20 to 27 wt%, and the second population texturally younger has lower total REE concentration ranging from 14 to 19.9 wt%, which occur as a rim surrounding the older and likely arose during the K alteration with Cu-Au mineralization (third crystallization). Differences between the two allanite populations are documented by both optical properties and analysis of their chemical composition. The last parameter indicate that the studied allanites belong to the Ce-La-ferriallanite family, with low HREE with an average of 0.21 wt.%. Temperature 355ºC which was calculated using value of δ34S isotopes is interpreted as a temperature of the second crystallization stage of allanite. The pressure of crystallization solution was calculated and is ranging from 0.98 to 5.88 MPa.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

A nanostructured electrochemical bi-sensor system for analysis of milks has been developed using the Layer by Layer technique. The non-enzymatic sensor [CHI+IL/CuPcS]2, is a layered material containing a negative film of the anionic sulfonated copper phthalocyanine (CuPcS) acting as electrocatalytic material, and a cationic layer containing a mixture of an ionic liquid (IL) (1-butyl-3-methylimidazolium tetrafluoroborate) that enhances the conductivity and chitosan (CHI) that facilitates the enzyme immobilization. The biosensor ([CHI+IL/CuPcS]2-GAO) results from the immobilization of galactose oxidase on the top of the LbL layers. FTIR, UV-vis and AFM have confirmed the proposed structure and cyclic voltammetry has demonstrated the amplification caused by the combination of materials in the film. Sensors have been combined to form an electronic tongue for milk analysis. Principal Component Analysis has revealed the ability of the sensor system to discriminate between milk samples with different lactose content. Using PLS-1 calibration models, correlations have been found between the voltammetric signals and chemical parameters measured by classical methods. PLS-1 models provide excellent correlations with lactose content. Additional information about other components such as fats, proteins and acidity can also be obtained. The method developed is simple and the short response time permits its use in assaying milk samples on-line.

The Sanhetun tellurium-gold (Te-Au) deposit, located in the Duobaoshan polymetallic metallogenic belt (DPMB) within the eastern section of the Central Asian Orogenic Belt (CAOB), is a newly discovered small scale gold deposit. The mineralization, with resource of ≥ 4t Au, is mainly hosted in 3 NNE-trending alteration zones between granitic mylonite and volcanogenic-sedimentary formations. It’s the genesis and timing of formation of this deposit are poorly constrained. Here, we report the results of petrographic studies, TESCAN Integrated Mineral Analyzer (TIMA), major and trace element concentrations, and in situ S isotope of pyrite and U-Pb ages of calcite. The results show that there are five species of telluride, including native tellurium, tetradymite, tsumoite, hessite and petzite and four types of pyrite, including coarse-grained euhedral Py1, fine-grained quartz-Py2 vein crosscutting Py1 and anhedral aggregated Py3 and Py4. The pre-ore Py1, containing negligible Au, Te and other trace elements, have a relatively narrow range of δ34S values ranging from -1.20 to -0.57‰. The Py2 have slightly high concentrations of Au and Te and distinctly high concentrations of Mo, Sb, Zn and Mn with markedly positive δ34S values of 4.67 to 14.43‰. The main ore stage Py3 contains high Au and Te concentrations and shows narrow δ34S values ranging from -5.69 to 0.19‰. The post-ore stage Py4 contains low Au concentrations with the δ34S values ranging from 2.66 to 3.86‰. Calcite from ore stage yield a U-Pb age of 135 ± 22 Ma, interpreted as the age of Te-Au mineralization. Our geochemical and geochronological data indicate that the Te was derived from partial melting of mantle metasomatized by the Te-rich fluids that originated from oceanic sediments. We correlate the tectonic setting with the subduction of Paleo Pacific plate in Early Cretaceous.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

This paper intends to discuss SSLs, how they work, their advantages and drawbacks. It will end with the author’s thoughts on the efficacy of the system and whether it is a viable solution for the majority of network security problems or if those drawbacks prevent that.

The deposition of dust particles on solar panel modules constitutes a significant challenge, leading to a potential reduction in solar cell performance. This work tackles this issue by investigating the surface modification of a layer of transparent indium tin oxide (ITO), with a detailed analysis of the influence of its characteristics via different annealing conditions/processing. The ITO layer has been studied to enhance its characteristics for dust removal applications. Of particular note is that the developed ITO layer can be applied to dust removal using electrostatic or magnetic-based approaches. Thus, the correlation between annealing gas (using Argon, Oxygen, and Nitrogen), annealing temperature, and annealing ramping rate is explored with the obtained surface topography, as well as electrical and optical properties. The developed ITO layers annealed in the Argon medium at 600°C with an annealing ramping rate of 50°C/s showed smooth surface roughness, the highest electrical conductivity, and a relatively low refractive index. Such findings can play a crucial role in the future implementation of using the enhanced ITO layer for dust mitigation in solar panels, thus improving their long-term performance.

Debris-flows are recurrent events on mountain- and hill- slopes, and they have been the object of numerous field investigations and sampling, however most of this work reposes on imagery and outcrop analysis, in such a way that there are still only a handful of studies investigating the internal architecture of these events’ deposits. In the present contribution, we aims at underneath the internal structure of a portion of a debris-flow deposit that was accessible in the aftermath of the 2018 heavy-rainfall debris-flows in Hiroshima Japan. Using a Ramac Pro-Ex GPR with 500 MHz and 800 MHz antenna, a set of longitudinal and transversal transects was used to characterize the deposit. The results demonstrated that a set of subhorizontal layers have filled the valley, and interacting with local terrace edges, these layers have piled up and overcome the obstacle. Across the valleys, a set of trough suggest the presence of channels that were also filled during the event. Finally, in the channel post-event, a set of radargram “cross-bedded units” shows that the final deposition in the channel was of a more dilute flow, typical of a Newtonian flow. This set of units was not to be found at the surface of the post-event pseudo-surface, suggesting that the flow ended as a debris-flow on this surface, and that it is only when the flow dug the final channel that the nature of the flow returned from debris-flow to Newtonian flow.

The Ni-laterite deposit at the San Felipe plateau, located 30 km northwest of Camagüey, in cen-tral Cuba, is the best example of a clay-type deposit in the Caribbean region. San Felipe resulted from weathering of mantle peridotites of the Cretaceous Camagüey ophiolites. In this study, a geochemical and mineralogical characterization of two profiles (83 and 84) from the San Felipe deposit has been performed by XRF, ICP-MS, quantitative XRPD, oriented aggregate mount XRD, SEM, FE-SEM and EMPA. Core 83 with a length of 23 m, and drilled in the central part of the plateau, presents a notable concentration of cryptocrystalline quartz fragments and a rather poor content in NiO, averaging 0.87% wt. Core 84, which is 12 m long, and drilled at the border of the plateau, lacks silica fragments and presents a higher NiO content, averaging 1.79 %wt. The smectite structural formulae reveal that they evolve from trioctahedral to dioctahedral towards the top of the laterite profiles. Quantitative XRD analyses indicate that smectite is a dominant Ni bearing phase, accompanied by serpentine and minor chlorite. Serpentine, as smectite, is en-riched in the less soluble elements Fe3+, Al and Ni towards the top of the profiles. Core 83 seems to have been affected by collapses, replenishments, whereas core 84 may have remained undis-turbed.

This proposal describes the design and development of an interoperable application that supports green open access with long-term sustainability and improved user experience of article deposit. Introduction: The lack of library resources and unfriendly repository user interface are two significant barriers that hinder green open access. Tasked to implement the open access mandate, librarians at an American research university developed a comprehensive system called Easy Deposit 2 to automate the support workflow of green open access. Implementation: Easy Deposit 2 is a web application that is able to harvest newly publications, outreach for manuscript on behalf of the library, and facilitate self-archiving to IR. It is developed and maintained by the library and integrated with the IR. Results and Discussion: The article deposit rate is about 25% with Easy Deposit 2, which increases significantly comparing to the previous period. It also serves as a local database for faculty publications with open access status. The lesson learned is that library cannot rely on a single commercial provider for publication data due to mismatched priorities. Conclusion: Recent IT developments provides new opportunities of innovation like Easy Deposit 2 in supporting open access. Academic librarians are vital in promoting "openness" in scholarly communication such as transparency and diversity in the sharing of publication data.

The present Feature Paper highlights the application of bacterial surface (S-) layer proteins as versatile components for the fabrication of biosensors. One technologically relevant feature of S‑layer proteins is their ability to self-assemble on many surfaces and interfaces to form a crystalline 2D protein lattice. The S-layer lattice on the surface of a biosensor becomes part of the interface architecture, linking the bioreceptor to the transducer interface, which may cause signal amplification. The S-layer lattice as ultrathin, highly porous structure with functional groups in a well-defined special distribution and orientation and an overall anti-fouling characteristics can significantly raise the limit in terms of variety and ease of bioreceptor immobilization, compactness of bioreceptor molecule arrangement, sensitivity, specificity, and detection limit for many types of biosensors. The present paper discusses and summarizes examples for the successful implementation of S-layer lattices on biosensor surfaces in order to give a comprehensive overview on the application potential of these bioinspired S-layer protein-based biosensors.

Danyore Valley area is a new prospect of copper-gold mineralization in the Gilgit-Baltistan province, Kohistan terrane, northern Pakistan. The mineralization is Cu-Au vein-type, localized within quartz veins and controlled by a fracture system mainly trending NW and NE. The host units belong to the Ladakh-Kohistan arc terrane, which covers northern Pakistan and north-western India and mainly comprises Precambrian basement units, Paleozoic to Cenozoic magmatic rocks, and sedimentary strata. The mineralized wall rocks consist of Mesozoic gabbro and diorite, which have undergone an intensive hydrothermal alteration. The study area, Danyore Valley, has yet to be explored. The geological background and mineralization type in literature are scarce. Moreover, the tectonic setting, petrogenesis, age, and magmatic evolution of the gabbro-diorite hosting unit still need to be better understood. Furthermore, the sources of metals and mineralized fluids and the types of mineralization and alteration are also unexplored. This research's contribution presents the field investigation, microscopic observations, whole rock geochemistry (major, trace, and REE), mineral analysis (EPMA), in situ LA–ICP–MS zircon U–Pb age dating, and zircon trace elements data for Danyore Valley Cu-Au prospect of Kohistan Batholith. The current research work's objectives are to (a) constrain the emplacement ages of the Danyore Valley host rocks, (b) determine the petrogenesis and tectonic environment of the gabbro-diorite wall rocks, and (c) identify the mineralization style and alteration patterns of Cu-Au occurrences. The U-Pb isotopic data of studied zircons from Danyore Valley diorite specimens yielded concordia ages from 111.60 ± 0.90 Ma to 112.18 ± 0.74 Ma. Correspondingly, the gabbro rock sample displayed a concordia age of 110.21 ± 0.99 Ma, indicating the crystallization time of the host bodies is mainly the early cretaceous period (∼110 Ma). The findings of this study reveal that the calc-alkaline affinity and arc-like geochemical characteristics of the gabbro and diorite rocks have been characterized by a significant enrichment in large-ion lithophile elements and an apparent depletion in high-field strength elements. The parent magma probably originated from a partial melting process of mantle depletion, and geochemical traits are characteristic of magmas associated with subduction zones. The Danyore Valley area of Kohistan terrane is defined by the existence of several mineralized quartz veins, which are mainly sulfide assemblages. The sulfide ore is mainly comprised of chalcopyrite, pyrite, and bornite, with a smaller amount of covellite and sphalerite and significant traces of gold, which are distributed mainly in sulfides. Copper and gold mineralization of Danyore Valley is associated with phyllic, propylitic, and carbonatization alteration assemblages. Metal-rich quartz veins exhibit a spatial correlation with diorite and gabbro rocks. The discovery of several surface Cu-Au vein-type mineralized areas accompanying outcrops of copper supergene enrichment at the Danyore Valley prospect is significant evidence (predictor patterns) of porphyry-style deposits in the Gilgit district, Kohistan terrane, northern Pakistan. This work also advocates the importance of the Danyore Valley prospect and Kohistan Batholith region for further detailed geological studies.

Here, we investigate the actuation dynamics of a micro device with different intervening liquids between the actuating components under the influence of Casimir and dissipative hydrodynamic forces. This is enabled via phase space portraits, which demonstrate that by increasing the dielectric response of the intervening layer the device may not come into stiction due to the decreasing in magnitude Casmir force. Moreover, it is feasible to expand area of motion using intervening liquids with lower dynamic viscosity or increasing the slip length of the intervening fluid. Finally, under the influence of an external driven force, which is the realistic case for possible applications, the system can reach stable oscillation at larger separations with an amplitude higher for the liquid that lead to lower Casimir and hydrodynamic forces.

For enhancing the maximized profit from bank as well as customer perspective, term deposit can accelerate finance fields. This paper focuses on likelihood of term deposit subscription taken by the customers. Bank campaign efforts and customer details are influential while considering possibilities of taking term deposit subscription. An automated system is provided in this paper that approaches towards prediction of term deposit investment possibilities in advance. Neural network(NN) along with stratified 10-fold cross-validation methodology is proposed as predictive model which is later compared with other benchmark classifiers such as k-Nearest Neighbor (k-NN), Decision tree classifier (DT), and Multi-layer perceptron classifier (MLP). Experimental study concluded that proposed model provides significant prediction results over other baseline models with an accuracy of 88.32% and Mean Squared Error (MSE) of 0.1168.

Gold, present as electrum, in the Battle Gap, Ridge North-West, HW, and Price deposits at the Myra Falls mine, occurs in late veinlets cutting the earlier VMS lithologies. The ore mineral assemblage containing the electrum comprises dominantly galena, tennantite, bornite, sphalerite, chalcopyrite, pyrite and rare stromeyerite is defined as an Au-Zn-Pb-As-Sb association. The gangue is comprised of barite, quartz, and minor feldspathic volcanogenic sedimentary rocks and clay. Deposition of gold as electrum in the baritic upper portions of the sulphide lenses occurs at relatively shallow water depths beneath the sea floor. Primary, pseudosecondary, and secondary fluid inclusions, petrographically related to gold, show boiling fluid inclusion assemblages in the range of 123 to 173 °C, with compositions and eutectic melt temperatures consistent with seawater at approximately 3.2 wt% NaCl equivalent. The fluid inclusion homogenization temperatures are consistent with boiling seawater corresponding to water depths ranging from 15 to 125 metres. Slightly more dilute brines corresponding to salinities of approximately 1 wt% NaCl indicate that there is input from very low-salinity brines, which could represent a transition from subaqueous VMS to epithermal-like conditions for precious metal enrichment, mixing with re‑condensed vapour, or very low-salinity igneous fluids.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

This paper reports results of analysis of field ion emission mechanism from tungsten-epoxy composite emitters that are compared to tungsten nano-field emitters. In this context, the mechanism of emission from this type of emitters is described based on a theory of induced conductive channels. The tungsten emitters were prepared using the electrochemical polishing technique and coated with a layer of the epoxy resin. Field ion microscope (FIM) analyses are reported including the study of the emission-ion density distributions from both the uncoated and coated emitters. Two forms of emission patterns have been observed in the ion emission microscopy technique describing the differences in the emission mechanism of both types of emitters. The observed results show: (a) the expected crystalline surface atomic distribution images of the field ion microscopy in the case of uncoated tungsten tips, and (b) randomly distributed emission spots that describe the locations of the induced conductive channels inside the resin coating layer.

Pyrochlore group minerals are the main raw phases in granitic rocks of the Katugin complex-ore deposit that stores Nb, Ta, Y, REE, U, Th, Zr, and cryolite. They are of three main generations: primary magmatic (I), early postmagmatic (II), and supergene (III) pyrochlores. The primary magmatic phase (generation I) is fluornatropyrochlore with high concentrations of Na2O (to 10.5 wt.%), F (to 5.4 wt.%) and REE2O3 (to 17.1 wt.%) but low CaO (0.6-4.3 wt.%), UO2 (to 2.6 wt.%), ThO2 (to 1.8 wt.%), and PbO (to 1.4 wt.%). Pyrochlore of this type is very rare in nature and limited to a few occurrences, such as rare-metal deposits of Nechalacho in syenite and nepheline syenite (Canada) and Mariupol in nepheline syenite (Ukraine). It may have crystallized synchronously with or slightly later than melanocratic minerals (aegirine, biotite, and arfvedsonite) at the late magmatic stage when Fe from the melt became bound making impossible the formation of columbite. Second generation pyrochlore formed at the early postmagmatic stage of the Katugin deposit. It differs from that of first generation in lower Na2O concentrations (2.8 wt.%), relatively low F (4 wt.%), and les occupancy of the A and Y sites at similar contents of other components. Generation III pyrochlore is a product of supergene alteration processes. It is compositionally heterogeneous and contains K, Ba, Pb, Fe, and significant Si concentrations but low Na and F. Its compositions mostly fall within the filed of hydro- and kenopyrochlore.

The nephrite belt in Altun Mountain-Western Kunlun Mountain region spanning approximately 1300 km in Xinjiang, NW China, constituting the world's largest preeminent nephrite deposit. The Qiemo region in the Altun Mountain is a crucial nephrite-producing area in China with demonstrating substantial prospects for future explorationl. While extant research has extensively study on secondary deposits in the Karakash River and native black nephrite deposits in Guangxi Dahua, a lacuna exists in the comprehensive investigation of black nephrite from original deposits in Xinjiang. Margou nephrite represents a recent discovery of black-toned nephrite deposits in Qiemo County, Xinjiang, warranting a comprehensive investigation into this primary source of black nephrite within the region. This scholarly inquiry deploys a suite of sophisticated analytical techniques, encompassing Polarizing microscope, electric microprobe, Backscattered Electron Image, X-ray Fluorescence, Inductively Coupled Plasma Mass Spectrometry. The rigorous experimental test is dedicated to elucidating the chemical and mineralogical composition, and further clarify the type of its genetic types of black-black cyan nephrite from Margou deposit in Qiemo, Xinjiang. Results delineate the mainly composed of tremolite-actinolite, characterized by Mg/(Mg + Fe2+) ratios ranging from 0.86 to 1.0. Minor minerals include diopside, epidote, pargasite, apatite, zircon, pyrite and iron hydroxide. Bulk-rock rare earth element patterns exhibit distinctive features such as negative Eu anomalies (δEu=0.00~0.17), decreasing light rare earth elements, a relatively flat distribution of heavy rare earth elements, and low with total REE concentrations (1.64~38.9 μg/g), concurrently, the Cr (6~21 μg/g) and Ni (2.5~4.5 μg/g) contents are conspicuously low. The magmatic influence of granite emerges as pivotal factor in the genesis of magnesia skarn hosting the Margou nephrite. The distinctive black-black cyan colour is attributed to heightened iron content, mainly associated with FeO (0.08~6.29%). The discerned chemical composition characteristics posit the Margou nephrite as an exemplar of the magnesia skarn-type nephrite deposit.

OSI model used to be common network model for years. In the case of ad hoc networks with dynamic topology and difficult radio communications conditions, gradual departure is happening from the classical kind of OSI network model with a clear delineation of layers (physical, channel, network, transport, application) to the cross-layer approach. The layers of the network model in ad hoc networks strongly influence each other. Thus, the cross-layer approach can improve the performance of an ad hoc network by jointly developing protocols using interaction and collaborative optimisation of multiple layers. The existing cross-layer methods classification is too complicated, because it’s based on the whole manifold of network model layers combinations, regardless their importance. In this work, we review ad hoc networks cross-layer methods, propose the new useful classification of cross-layer methods, and show future research directions in ad hoc networks cross-layer methods development. The proposed classification can help to simplify the goal-oriented cross-layer protocol development.

A 9,10-phenanthrenequinone (PQ) was electrochemically polymerized on a graphite rod electrode using potential cycling. The electrode modified by poly-9,10-phenanthrenequinone (poly-PQ) was studied by means of cyclic voltammetry, electrochemical impedance spectroscopy, atomic force microscopy and scanning electron microscopy. The poly-PQ shows variations in growth pattern depending on the number of potential cycles for the initiation of polymerization. Formed poly-PQ layer demonstrates good electric conductivity, great electrochemical capacitance and unique oxidation/reduction properties, which are suitable for broad technological applications, including applicability in biosensors, supercapacitors, and in some other electrochemical systems.

This paper provides a comprehensive evaluation of the environmental impact of implementing the beverage container DRS on marine and coastal litter along the Latvian coastline. It incorporates data and insights from the assessment of deposit fractions litter in coastal areas during the post-season autumn period in three monitoring sessions from 2021 (before the introduction of the DRS in Latvia) to 2023 (post-introduction). In 2022, a 43% overall decrease in selected public coastal areas was observed, with significant reductions at 11 out of 17 sites. This positive trend continued in 2023, showcasing a further 22% decrease compared to 2022 and a substantial 56% decrease compared to 2021. The study delves into the specific impact on different material types of beverage containers, reporting significant decreases in plastic and aluminum litter fractions. While glass beverage container litter showed a smaller decrease, overall positive trends continued in 2023. However, the situation with aluminum cans remained challenging, especially in border areas with Lithuania and Estonia. The study emphasizes that beverage containers with identifiable deposit system labels constitute a minority of the total litter pressure, underscoring the need for ongoing efforts to address containers without deposit labels, particularly in specific border areas. The findings provide valuable insights into the effectiveness of the deposit system in mitigating coastal litter, contributing to sustainable waste management practices in Latvia.

Selenium-rich Au-Ag mineralization has been discovered in the Kremnica ore district, central Slovakia. The mineralization is hosted by a single quartz-dolomite vein hosted by Neogene propyllitized andesites of the Kremnica stratovolcano. Ore mineralogy and crystal chemistry of individual ore minerals have been studied here. The early base-metal ore mineralization composed of pyrite, sphalerite and chalcopyrite lacks selenium, whereas the superimposed Au-Ag paragenesis is Se-enriched. The Au-Ag alloys, uytenbogaardtite, minerals of the galena-clausthalite series, acanthite-naumannite series, diaphorite, miargyrite, pyrargyrite-proustite, polybasite group, minerals of the tetrahedrite group and andorite branch (andorite IV, andorite VI, Ag-excess fizélyite), freislebenite, and rare Pb-Sb sulphosalts (scaiinite, robinsonite, plagionite) have been identified here. Besides selenides, the most Se-enriched phases are miargyrite, proustite-pyrargyrite, and polybasite-pearceite, whose Se contents are among the highest reported worldwide. In addition, one new phase has been found, corresponding to a Se-analogue of pearceite containing 2.08 - 3.54 apfu Se. The style of mineralization, paragenetic situation, and chemical trends observed in individual minerals are comparable to those of Au-Ag low-sulphidation epithermal Au-Ag mineralizations of the Kremnica and neighboring Štiavnica and Hodruša-Hámre Ore Districts, however, the pronounced enrichment in selenium is a specific feature of the studied vein only.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Carburizing of stainless steels at low temperatures (below 500°C) develops a high content carbon layer, known for its high hardness. X-ray Diffraction investigation indicates that carburization treatment does not impact the structure of substrate; however, introduced carbon causes expansion in the carburized layer through the increase in d-spacing. Characterization of carbon concentration and hardness profiles indicate that carbon content gradually decreases while moving further into the substrate; and the origin of the increased hardness of the expanded layer arises from the super-saturated carbon content, following the solid solution strengthening theory. An area that is not well understood is in regard to the carburized layer’s relation to the substrate and the significance in their differences. Using two grades of stainless steel, AISI 316L and PH 17-4, it was observed that the carburized layer is not a separate layer, but a higher carbon content version of the substrate,

This study identifies the facies and degrees of hydrothermal alteration related to the low sulphida-tion epithermal Kestanelik Au deposit in the Biga Peninsula metallogenic province through petro-graphic studies and analysis of geochemical characteristics, such as mass changes, molar element ratios, and alteration indices. The gold mineralization is located in silicified zones containing veins and stockwork veinlets of quartz. These zones are found within the Permian-Upper Cretaceous aged Çamlıca basement metamorphics and Eocene aged Kestanelik granodiorite of the Karabiga Massif on the Biga Peninsula. The mineralization is influenced by tectonic structures such as quartz veins and faults. In the Kestanelik Au deposit, common hydrothermal alteration occurs mainly in the metamorphics and granodiorite, and less often in volcanic rocks. Based on miner-alogical and geochemical studies conducted on altered samples, four different alteration facies were defined as silicic, sericitic, argillic and propylitic, which show remarkable differences in the behaviour of REE, Si, K, Al, Na and Ca elements. The characterization of rocks subjected to hy-drothermal alteration that are most influenced by diverse K metasomatism with the largest K gains and losses of Na-Ca, is illustrated by molar element ratio plots. Depending on the severity of K-metasomatism, gold mineralization rises with increasing K trends towards gold ore veins. In the Kestanelik Au field, the alteration types of argillic, sericitic, propylitic and adularia from the alter-ation zones enclosing the Au ore veins, were revealed by the alteration index and chlo-rite-carbonate-pyrite index. Mass changes in the altered rocks indicate that there are gains in Si, K, Al, and losses in Na and Ca with the increasing intensity of alteration towards the Kestanelik ore veins. The results confirm the presence of silicic and K-metasomatic (sericite and argillic) propylit-ic (Fe-rich chloride) alteration zoning extending from the inner regions to the outer regions, which characterize the epithermal ore systems. It has been revealed from the data obtained in this study that the intensity of potassium metasomatism that occurs in acidic rocks is greater than that found in intermediate and mafic rocks. The hydrothermal fluids that cause alteration in Kestanelik Au mineralization and host rocks had low contents of REE due to REE mobilization, and the kaolini-zation of feldspars and micas, and the chloritization of biotite and feldspars, may cause negative Eu anomalies.

Based on the analysis of the spatial distribution of uranium grade in 348 boreholes of a uranium deposit in Xinjiang, the enrichment and spatial variation of uranium ore in two stopes of the deposit are discussed by using multifractal theory. The distribution characteristics of uranium ore of the two stopes are studied by multifractal parameters: the scaling exponent of mass , the scaling exponent of each sub-set and its corresponding fractal dimension , the fractal dimension D0 and information dimension D1. The differences of uranium distribution in two stopes can be well quantified by multifractal spectrum and multifractal parameters( , , ).10m×10m is defined as a fence unit, and the window sizes are respectively set, the singularity exponent of the two stopes are calculated by this element concentration-area(C-A) method. The results show that the multifractal theory and model can organically combine spatial structure information, scale change information and anisotropy information to obtain low-grade and weak mineral resources information, and can effectively distinguish complex and superimposed anomalies. This will provide a basis for local concentration and spatial variation rules of uranium distribution and the design of the parameters of leaching uranium mining well site.

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

Introduction: Migraine is one of the most prominent headache disorders with a global burden of over one billion patients and presented as a disabling and painful disorder. Pathophysiological mechanism of migraine is not fully understood, but the most accepted theory suggests that migraine is caused primarily by neural dysfunction leading to secondary changes in cerebral perfusion. Methods: Authors conducted a case-control study in 175 patients; 88 of them were migraineurs and 87 health controls. Optical coherence tomography (OCT) was performed in all patients using spectral-domain OCT device in the same environmental conditions. All participants met both inclusion and exclusion criteria in order to achieve more homogeneous groups. OCT was performed to scan all retinal layers with an emphasis on the inner plexiform layer (IPL). Results: Among 175 examined subjects, 84% of them were women and in the group of migraineurs we found 56% without aura and 44 % with aura. After collecting tomography data authors did not find subjects in which changes of IPL were found. Nevertheless, only moderate differences in the IPL thickness in all quadrants except the central area were found in the group of migraineurs with aura using Pearson’s test. Conclusion: According to presented results, no significant changes of the IPL thickness in migraine patients were found. Authors have to emphasize the need for further investigation of the relationship between average migraine headache days per month and the thickness of the IPL.

To achieve an acceptable level of security on the web, the Completely Automatic Public Turing test to tell Computer and Human Apart (CAPTCHA) was introduced as a tool to prevent bots from doing destructive actions such as downloading or signing up. Mobile devices have small screens, and therefore, using the common CAPTCHA methods (e.g. text CAPTCHAs) in these devices raises usability issues. To introduce a reliable, secure, and usable CAPTCHA that is suitable for mobile devices, this paper introduces a hand gesture recognition CAPTCHA based on applying Genetic Algorithm (GA) principles on Multi-Layer Perceptron (MLP). The proposed method improves the performance of MLP-based hand gesture recognition. It has been trained and evaluated on 2201 videos of the IPN Hand dataset, and MSE and RMSE benchmarks report the index values of 0.0018 and 0.0424, respectively. Comparison with the related works shows a minimum of 1.79% fewer errors, and experiments produced a sensitivity of 93.42% and accuracy of 92.27% – 10.25% and 6.65% improvement compared to the MLP implementation.

Flexible polymer-based dye-sensitized solar cells (DSSCs) offer promising potential for lightweight, cost-effective and versatile photovoltaic applications. However, the critical challenge in their widespread applications is the weak thermal stability of the majority of polymeric substrates, which can only withstand a maximum temperature processing of 150°C. In this study, we propose a facile and low-cost strategy to develop at low temperature DSSC flexible photoanode based on a polymeric matrix. Highly porous nanocomposites fibrous mats composed of polyethylene terephthalate (PET) and titanium dioxide (TiO2) nanobars were prepared through electrospinning process using different configurations (uniaxial electrospinning, coaxial electrospinning, and electrospray-assisted electrospinning). These techniques enabled precise control of the microstructure and the positioning of TiO2 within the composite nanofibers. Therefore, the as-produced photoanodes were loaded with N719 dye and tested in DSSC prototype using iodide-triiodide electrolyte and platinum (Pt) coated counter electrode. The results show that incorporating TiO2 on the fiber surface through the electrospray-assisted electrospinning enhanced the performance of the nanofiber composite, leading to improved dye loading capacity, electron transfer efficiency and photovoltaic performance.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

The Huayangchuan uranium deposit, located in the west of the Xiaoqinling belt on the southern margin of the North China Craton, is a polymetallic deposit dominated by U, Nb, Pb, and rare earth elements. The Huayangchuan uranium deposit, discovered in the 1950s, has long been known as a carbonatite-type uranium deposit. Recently, new geological work has found uranium mineralisation in many granitic pegmatite veins in the Huayangchuan deposit and adjacent areas. Here, we report a systematic investigation of the petrography, whole-rock geochemistry, zircon U-Pb ages, and in situ Lu-Hf isotopic characteristics of newly discovered U-rich granitic pegmatite veins in the west of Huayangchuan deposit. The petrological results showed that the lithology of the samples is equivalent to that of granite. The U-Pb ages of zircon were 1826.3 ± 7.9 and 1829 ± 11 Ma. Microscopically, the symbiotic characteristics of zircon, betafite, and uraninite exist in the intergranular fissures of K-feldspar and quartz, reflecting metallogenic phenomena in the rock formation process. Almost all whole-rock samples were rich in SiO2 (64.37–70.69 wt.%), total alkalis (K2O+Na2O = 8.50–10.30 wt.%), and Al2O3 (12.20–14.41 wt.%), but poor in Ti2O (0.23–0.73 wt.%), MgO (0.38–0.90 wt.%), P2O5 (0.14–0.83 wt.%), MnO (0.04–0.57 wt.%). Additionally, they showed enrichment of LILEs (such as Rb, Ba, Th, U, and K), depletion of HFSEs (such as Ta, Nb, P, Ti, and Hf), no alkaline dark minerals, and the characteristics are typical of intraplate A1-type granite. The A1-type granite displayed low zircon εHf(t) values (-19.42– -15.02) with zircon two-stage Hf model aged 3.10–2.76 Ga, indicating that the U-rich granitic pegmatite was derived predominantly from partial melting of the ancient continental crust (such as the early Taihua group formed in Archean-Neoarchean). Combined with the above results and regional geological data, the U-rich granitic pegmatite discovered in the Huayangchuan deposit was related to granite magma activity that formed in a post-collisional regime after the Luliang movement in the late Palaeoproterozoic. This study suggests that future uranium prospecting work in this area should focus on late Palaeoproterozoic U-rich granitic pegmatites.

Tsygankoite, ideally Mn8Tl8Hg2(Sb21Pb2Tl)Σ24S48, is a new sulfosalt discovered at the Vorontsovskoe gold deposit, Northern Urals, Russia. It occurs as lath-like elongated crystals up to 0.2 mm embedded in calcite-dolomite-clinochlore matrix. The associating minerals also include aktashite, alabandite, arsenopyrite, barite, cinnabar, fluorapatite, orpiment, pyrite, realgar, routhierite, sphalerite, tilasite, titanite, etc. The new mineral is non-fluorescent, black, opaque with a metallic lustre and black streak. It is brittle with an uneven fracture and no obvious parting and cleavage. Its Vickers hardness (VHN10) is 144 kg/mm2 (range 131–167) and its calculated density is 5.450 g cm-3. In reflected light tsygankoite is white; between crossed polars it is dark-grey to black. It is strongly anisotropic: rotation tints vary from light-grey to dark-grey to black. Pleochroism and internal reflections are not observed. The chemical composition of tsygankoite (wt.%, electron-microprobe data) is: Mn 6.29, Fe 0.02, Cu 0.02, Ag 0.01, Hg 5.42, Tl 26.05, Pb 5.84, As 3.39, Sb 30.89, S 21.87, Se 0.01, total 99.81. The empirical formula, calculated on the basis of 90 atoms pfu, is: Mn8.06Tl8.00(Hg1.90Fe0.03Cu0.02Ag0.01)Σ1.96(Sb17.85As3.18Pb1.98Tl0.97)Σ23.98(S48.00Se0.01)Σ48.01. Tsygankoite is monoclinic, space group C2/m, a = 21.362(4) Å, b = 3.8579(10) Å, c = 27.135(4) Å, β= 106.944(14)°, V = 2139.19(17) Å3 and Z = 1. The five strongest diffraction peaks from X-ray powder pattern [listed as (d,Å(I)(hkl)] are: 3.587(100)(112), 3.353(70)(-114), 3.204(88)(405), 2.841(72)(-513) and 2.786(99)(-514). The crystal structure of tsygankoite was refined from single-crystal X-ray diffraction data to R = 0.0607 and consists of an alternation of two thick layer-like arrays, one based on PbS-archetype and second – on SnS-archetype. Tsygankoite has been approved by the IMA-CNMNC under the number 2017-088. It is named for Mikhail V. Tsyganko, mineral collector from Northern Urals, who collected the samples where the new mineral was discovered.

This work shows the preliminary description of the origin of a sedimentary - exhalative outcrop of Jurassic Lower Pliensbachian. The location of this deposit was achieved by applying an examination based in the identification of sedimentary transgressions of heterochronies ages and the identification of a Rift – type mega –structure. According with the methodology, it was carried out a study of the discordant relationships between two types of sediments: continental and marine. According the characterization, it was noted the existence of light rare earths, in values that show positive anomalies in comparison with the distribution of elements in upper continental crust according to the Clarke [1], reflecting so a felsic affinity of the mineral deposit. Also, positive anomalies of platinum and Pd, were determined with marginal contents of Au and Ag; and finally the base metals Zn, Pb and Cu were detected in low contents, which could be due to the presence of altered shale. According to the sedimentary lithology found, which was of siliciclastic type; to the exhalative roots observed during the fieldwork; the presence of quartz minerals such as biotite and muscovite; the presence of minerals of hydrothermal remobilization like chalcopyrite with some base metals, altered shale, as well as sulfur deficiency; this mineral reservoir could be defined as a SEDEX – type.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

This study considers the features of the chemical composition, internal structure, and oscillatory zoning of sulfides, sulfosalts and sulfates in the epithermal high-intermediate sulfidation type Au-Ag-Te Emmy deposit (Khabarovsk Territory), Russia. In this deposit the most widespread sulfide is pyrite occurring in two generations: pre-ore pure pyrite (I) with cubic crystal habit and dimensions from 20 μm to 0.5 mm from the early barren pre-ore hydrothermal stage, and pyrite (II) of the ore stage, which is represented by (a) colloform aggregates (IIa) formed as a result of rapid precipitation from the solution, and (b) crystalline pyrite (IIb), which is precipitated due to continuous decrease in temperature. Both pyrite (II) morphological varieties contain copper (0.06-6.03 wt.%). The crystalline variety of pyrite is associated with goldfieldite, hemusite and kawazulite which were deposited during the early mineralizing event in the deposit.

Fires are a significant threat to people, property, and environment. One of the requirements for the buildings during fires is ensuring the safe evacuation of persons. The evacuation assessment has usually been based on a comparison of the Required Safe Egress Time (RSET) and the Available Safe Egress Time (ASET). One of the important factors influencing the safe evacuation of persons is smoke, which is an important accompanying phenomenon in the burning of polymers. The smoke layer interface is one basic barrier for effective evacuation. The current calculation technique for assessing the smoke layer interface in the Czech Republic is unsatisfactory. For this reason, a calculation technique CSN has been derived, which has been compared with the selected simple calculation techniques, the zone fire model Consolidated Model of Fire and Smoke Transport (CFAST) and the field type model Fire Dynamics Simulator (FDS). The CSN technique was also compared with a real large-scale experiment. The data were also subjected to statistical evaluation using the root mean square error method (RMSE). The deviations between the NFPA, ISO and CSN calculation techniques, the CFAST and FDS fire models and the implemented experiment ranged from 0.05 to 2.41. The established deviations indicate that the calculation technique CSN will be practically usable.

In recent years, antibacterial coatings have become a significant approach in the global fight against bacterial pathogens. Developments in materials science, chemistry and biochemistry have led to a plethora of materials and chemical compounds that have potential for creating antibacterial coatings. Nonetheless, there has been insufficient consideration given to the analysis of the techniques and technologies used to apply these coatings. Among the various inorganic coating techniques, Atomic Layer Deposition (ALD) is noteworthy. It enables the successful synthesis of high-purity inorganic nanocoatings on surfaces of complex shape and topography, while also providing precise control over their thickness and composition. ALD has various industrial applications, but its practical application in medicine is still limited. In recent years, a substantial number of papers have been published on the suggested implementation of thin films and coatings produced through ALD in medicine, notably those with antibacterial properties. The aim of this paper is to carefully evaluate and analyse the relevant literature on this subject. Simple oxide coatings, including TiO2, ZnO, Fe2O3, MgO, and ZrO2, were examined, as well as coatings containing metal nanoparticles such as Ag, Cu, Pt, and Au, and mixed systems such as TiO2-ZnO, TiO2-ZrO2, ZnO-Al2O3, TiO2-Ag, and ZnO-Ag. Through comparative analysis, we have been able to draw conclusions on the effectiveness of various antibacterial coatings of different compositions, including key characteristics such as thickness, morphology, and crystal structure. ALD has been analysed in its use for developing antibacterial coatings for various applications. Furthermore, assumptions regarding the most promising development areas have been presented.

A solution for the Prandtl-Blasius equation is essential to all kinds of boundary layer problems. This paper revisits this classic problem and presents a general Maple code as its numerical solution. The solutions were obtained from the Maple code, using the Runge-Kutta method. The study also considers convergence radius expanding and an approximate analytic solution is proposed by curve fitting. Similarly, the study resolves some boundary layer related problems and provide relevant Maple codes for these.

Recently Li et al (2019 Nature 572 624) discovered a new type of oxide superconductor Nd_0.8Sr_0.2NiO₂ with T_c = 14 K. To classify superconductivity in this infinite-layer nickelate experimental upper critical field, B_c2(T), and the self-field critical current densities, J_c(sf,T), reported by Li et al (2019 Nature 572 624), are analysed in assumption of s-, d-, and p-wave pairing symmetries and single- and multiple-band superconductivity. Based on deduced the ground-state superconducting energy gap, Δ(0), the London penetration depth, λ(0), the relative jump in electronic specific heat at T_c, ΔC/C, and the ratio of 2Δ(0)/k_BT_c, we conclude that Nd_0.8Sr_0.2NiO₂ is type-II high-κ weak-coupled single-band s-wave superconductor.

In a thin-volume photobioreactor where a concentrated suspension of microalgae is circulated throughout the established spatial irradiance gradient, microalgal cells experience a time-variable irradiance. Deploying this feature is the most convenient way of obtaining the so-called “flashing light” effect, improving biomass production in high irradiance. This work investigates the light flashing features of sloping wavy photobioreactors, a recently proposed type, by introducing and validating a Computational Fluid Dynamics model. Two characteristic flow zones (straight top-bottom stream and local recirculation stream), both effective toward light flashing, have been found and characterised: a recirculation-induced frequency of 3.7 Hz and straight flow-induced frequency of 5.6 Hz were estimated. If the channel slope is increased, the recirculation area becomes less stable while the recirculation frequency is nearly constant with flow rate. The validated CFD model is a mighty tool that could be reliably used to further increase the flashing frequency by optimising the design, the dimensions, the installation and the operational parameters of the sloping wavy photobioreactor.

Mixing layer height (MLH) is a crucial parameter for air quality modelling that is still not routinely measured. Common methods for MLH determination use atmospheric profiles recorded by radiosonde but they suffer from course temporal resolution since balloon launching is only twice a day. Recently cheap ceilometers are gaining popularity in the retrieval of MLH diurnal evolution based on aerosol profiles. This study presents a comparison of a proprietary (Jenoptik) and a free available (STRAT) algorithms to retrieve MLH diurnal cycle. The comparison is accomplished in summer season over urban area and radiosonde data is used to estimate MLHs according to parcel, lapse rate, and Richardson methods (the last algorithm is used as a reference in the study) in addition. It was found that STRAT and Jenoptik give lower MLH than radiosonde with an underestimation of about 150m and 650m respectively. Additionally, STRAT showed reasonable performance in tracking of MLH diurnal evolution. Daily MLH maximum of about 2000m was found in the late afternoon (18-19 LT). In contrast, Jenoptik algorithm showed more weaknesses, mainly attributed to its real-time operation and independent processing of a single profile. At night and during morning transition period, both lidar-based methods showed difficulties as MLH was often in the ceilometer’s incomplete overlapping zone so residual or advected aerosol layers aloft were misleadingly reported as mixing layer (ML).

An integrated two-stage metallurgical technology has been developed for processing concentrates from the Olimpiadinskoe deposit with high antimony and arsenic content. The parameters of the alkaline sulphide leaching process of the initial concentrate of the Olimpiadinskoe deposit, providing maximum extraction of antimony in solution at 99% level have been recommended. The L:S ratio = 4,5:1; the concentration of sodium sulphide - 61 g/L; the concentration of sodium-hydroxide – 6,5 g/L; the duration – 3 hours; the temperature – 50 °C. A synergistic effect of alkaline sulphide leach cakes co-processing by sulphuric and nitric acids has been determined. Pre-treatment allows to reduce the composition of nitric acid by converting the carbonates into gypsum and increases the extraction of arsenic by 15 % at the following nitric leaching. Laboratory research of nitric acid leaching of decarbonized cake allowed to set the basic parameters for maximum iron and arsenic extraction in solution (92 and 98 %): the L:S ratio =9:1; the concentration of nitric acid – 6 mol/L; the time – 90 min. The full polynomial equations for iron and arsenic extraction from decarbonised cake have been derived. The model is relevant since the value the determination coefficients for iron and arsenic R2 were 96,7 and 93,2 %. The high value of gold recovery from the cake of two-stage alkaline sulphide and nitric acid leach cake at 95 % has been established. The maximum value of arsenic deposition from the nitrate leach solution in the form of the insoluble deposition As2S3 99,9 %. A basic technological flowsheet diagram for flotation gold-antimony processing for the Olimpiadinskoe deposit has been developed; it includes two redistributions: production of metallic antimony and gold extraction from the nitric leach cake.

Porphyry copper-molybdenum deposits (PCDs) are the world’s most important source of copper, molybdenum and rhenium. Previous studies have reported that some PCDs can have sub-economic to economic grades of critical metals, i.e., those elements that are both essential for modern societies and subject to the risk of supply restriction (e.g., platinum group elements (PGE), rare earth elements (REE), In, Co, Te, Ge, Ga, among others). Even though some studies have reported measured concentrations of Pd and Pt in PCDs, their occurrence and mineralogical form remain poorly constrained. Furthermore, these reconnaissance studies have focused predominantly on porphyry Cu-Au deposits, but very limited information is available for porphyry Cu-Mo systems. In this contribution, we report the occurrence of critical metal (Pd, Pt, Au, Ag, and Te) inclusions in copper sulfides from the world’s largest PCD, the supergiant Río Blanco-Los Bronces deposit in central Chile. Field emission scanning electron microscope (FESEM) observations of chalcopyrite and bornite from the potassic alteration zone reveal the presence of micro- to nano-sized particles (<1-10 μm) of noble metals, most notably Pd, Au, and Ag. The high-resolution data show that these inclusions are mostly tellurides, such as merenskyite [PdTe2], Pd-rich hessite [Ag2Te], sylvanite [(Ag, Au)Te2] and petzite [Ag3AuTe2]. The data point to Pd (and probably Pt) partitioning in copper sulfides during the high-temperature potassic alteration stage, opening new avenues of research aimed at investigating not only the mobility of PGE during mineralization and partitioning into sulfides, but also at evaluating the potential of porphyry Cu-Mo deposits as a source for noble metals.

Carbonaceous material (CM) is common in meta-sediments and is generally interpreted to be intimately associated with gold mineralization. For the Bumo deposit in Hainan Province, South China, CM is mainly hosted by greenschist facies- to amphibolite-facies metamophic rocks of the Paleo- to Mesoproterozoic Baoban Group and by auriferous veins and is used as an important gold prospecting indicator. However, the genesis of CM and the relationship with gold mineralization are still not clear. Field work and thin section observation indicates that two types of CM occur, i.e., layered and veinlet. Layered CM, up to meters thick, prevails in the deposit. More importantly, Au-bearing sulfides are commonly distributed along the boundary between the quartz veins and layered CM. In contrast, veinlet CM, co-precipitated with gold and sulfides, has the thickness of micro- to centi- meters, and these thin veins occur in quartz veins and hydrothermally altered rocks. Scanning Electron Microscope (SEM) analysis indicates that layered CM has a stringy shape and laminate structure, while veinlet CM occurs as isometric particles. Raman carbonaceous material geothermometer indicates that layered CM with high maturity is formed at elevated temperatures of 400 – 550°C, consistent with X-ray diffraction (XRD) analysis. In contrast, veinlet CM with low maturity is formed at 200 – 350°C, generally consistent with gold mineralization. In addition, layered CM has δ13C values ranging from -30 to -20%, demonstrating a biogenic origin. Consequently, it is interpreted that layered CM is formed by a pre-ore metamorphic event during Caledonian, and its reducing nature promotes gold precipitation via destabilization of aqueous Au bisulfide complexes or facilitating sulfidation. Veinlet CM is hydrothermal origin, and its precipitation modified the chemical conditions of ore fluids, leading to the destabilization of Au complexes and thus favorable for mineralization.

While there are extensive studies on the mineralogy and geochemistry of laterites worldwide, the temporal and spatial mineralogical development of a typical nickel laterite profile is still poorly constrained. In this study, we present a detailed mineralogical and geochemical characterization of samples systematically collected from a nickel laterite profile at the Sta. Cruz nickel laterite deposit, Zambales, Philippines, to describe the temporal and spatial development of the laterite profile. Wavelength-dispersive X-ray fluorescence spectroscopy (WDSXRF), mass balance-element mobility calculations, transmitted and reflected light microscopy, and previously reported results from coupled X-ray diffraction (XRD) and Rietveld refinement analyses, reveal that the laterite profile investigated is composed of two main horizons: the limonite and saprolite zones, separated by a thin transitional zone. The main zones are further subdivided into subzones based primarily on the mineral assemblage and major element chemistry: upper limonite, lower limonite, transitional zone, upper saprolite, and lower saprolite. Late-stage Ni-rich serpentine veins were observed cutting the upper and lower saprolite subzones. Investigation of the structure of goethite within the limonite zone via Rietveld refinement show that the crystallinity of goethite decreases with increasing Ni content and increasing crystallite size. This suggests that upwards through the limonite zone, as goethite ages, its crystallinity increases which possibly results in the removal of Ni from its crystal structure and eventual remobilization to the lower laterite zones. We propose a genetic model of the formation of the Sta. Cruz laterite consisting of four stages: (1) early-stage alteration, (2) continued serpentinization and volume expansion, (3) late stage serpentinization, dissolution, and incipient oxide formation, and (4) goethite ageing and Ni-rich serpentine vein formation. Overall, our results suggest that serpentinization is an important aspect of Ni laterite formation, both before and after the emplacement of the peridotite protolith.

: In today’s rapidly expanding era of the Internet of Things (IoT) and the Industrial Internet of Things (IIoT), the emphasis on robust data security and insightful data interpreta- tion is more pronounced than ever. This research introduces a comprehensive approach to both data protection and predictive analytics, leveraging the diverse dataset TON IoT.csv, sourced from a myriad of IoT and IIoT environments. For data security, a dual-encryption technique incorporating both AES and RSA algorithms is established. Its efficacy is evidenced by a perfect match between the original and decrypted datasets, underscoring the integrity of our encryption process. Concurrently, the study ventures into predictive modeling using a modified Snake Optimization Algorithm (SOA) to streamline hyperparameter selection. This subsequently aids in the development and fine-tuning of an LSTM network, which exhibits remarkable predictive accuracy. Additionally, the paper provides an in-depth examination of various encryption methodologies like elliptic curve cryptography (ECC), Lightweight Cryptography for Cloud computing, and homomorphic encryption, while also emphasizing the nuances of encryption in cloud setups, particularly contrasting server-side with client-side encryption and efficient key management. The insights presented serve as a cornerstone for ensuing research, promising a bright future for advancements in IoT and IIoT data protection and analysis

The studies of laminar unsteady boundary layer flows is crucial for understanding laminar-turbulence transition and origins of turbulence. However, the task of finding its solutions poses a significant challenge. In this paper, we propose a novel approach by introducing a similar transformation to convert the 2D unsteady laminar boundary layer equations into a single partial differential equation. By applying this transformation, we are able to obtain the "exact" similarity solutions for the 2D unsteady laminar boundary layer equations, specifically for the case of flat plate boundary flow. Notably, this is the first time that such an exact solution has been obtained. Application of this exact solution is being used to solve Stokes' first problem in 2D boundary layer. Perspectives on the transition fron Rayleigh solution to Blasius solution is provided.

This study introduces an alternative to the existing methods for measuring ocean currents based on a recently developed technology. The SailBuoy is an unmanned surface vehicle powered by wind and solar panels that can navigate autonomously to predefined way-points and record velocity profiles using an integrated downward-looking Acoustic Doppler Profiler (ADCP). Data, collected on two validation campaigns, shows a satisfactory correlation between the SailBuoy current records and traditional observation techniques such as bottom mounted and moored current profilers and moored single-point current meter. While the highest correlations were found in tidal signals, strong current, and calm weather conditions, low current speeds and varying high wave and wind conditions reduced correlation considerably. Filtering out some events with high sea surface roughness associated with high wind and wave conditions may increase the SailBuoy ADCP listening quality and lead to better correlations. Not yet resolved is a systematic offset between the measurements obtained by the SailBuoy and the reference instruments of ± 0.03 m/s. Possible reasons are discussed to be the differences between instruments (various products) as well as changes in background noise levels due to environmental conditions.

Cross-laminated timber (CLT) possesses both good shape stability and the possible two-way force transfer ability due to its crosswise lamination. However, the transverse layers in CLT are prone to rolling shear failure under an out-of-plane load. An innovative multi-layer composite laminated panel (CLP) was developed by combining structural composite lumber (SCL) and dimension lumber to overcome the rolling shear failure while maintaining high mechanical performance and aesthetic appearance of natural wood. The mechanical properties of 5-layer CLP consisted of laminated strand lumber (LSL) and dimension lumber with different layups were evaluated by both static and modal tests. The results showed that the shear resistance, bending stiffness and moment resistance of CLP were up to 143%, 43% and 87% higher than their counterparts of regular CLT, respectively. The failure modes observed in both shear and bending tests indicated that the use of LSL in transverse layers could eliminate the potential rolling shear failure in CLT. With the lamination properties from components tests as inputs, the validity of shear analogy method was assessed by test results. The mechanical properties can be well predicted by shear analogy method except for the bending moment resistance of CLP and CLT with either rolling failure in the cross layer or tension failure in the bottom layer.

In this paper, we introduce a comprehensive solution aimed at enhancing the understanding of three-dimensional atmospheric pollutant dispersion. This innovative solution develops a generalized model that extends previous research and is applicable to all parameterization schemes of the equation, including wind speed profiles and turbulent diffusion coefficients, while incorporating the dry deposition criterion. Our methodology involves subdividing the atmospheric boundary layer into distinct sublayers, which facilitates a detailed examination of pollutant dispersion dynamics. Extensive validation with data from the Hanford experiment has demonstrated the accuracy of this solution in simulating pollutant concentrations. The results exhibit a strong correlation between projected and observed concentrations, underscoring the statistical reliability of our approach. This validation situates the statistical indices of our solution within an acceptable range, confirming its accuracy in predicting atmospheric pollutant dispersion. These findings thus establish our solution as a valid and effective method for studying complex environmental phenomena.

In recent decades, considerable attention has been focused on the design and development of surfaces with defined or tunable properties for a wide range of applications and fields. To this end, self-assembled monolayers (SAMs) of organic compounds offer a unique and straightforward route of modifying and engineering the surface properties of any substrate. Thus, alkane-based self-assembled monolayers constitute one of the most extensively studied organic thin-film nanomaterials, which have found wide application in antifouling surfaces, control of wettability or cell adhesion, sensors, optical devices, corrosion protection, organic electronics, among many other applications. Some of which have led technological transfer to industry. Nevertheless, recently, aromatic-based SAMs have gained in importance as functional components, particularly in molecular electronics, bioelectronics, sensors, etc., due to their intrinsic electrical conductivity and optical properties, opening up new perspectives in these fields. However, some key issues affecting device performances still need to be lifted off to ensure their full use and access to novel functionalities such as memories, sensors, or active layers in optoelectronic devices. In this context, we will present herein recent advances of p-conjugated systems-based self-assembled monolayers (e.g., push-pull chromophores) as active layer and their applications.

The wheat aleurone layer is, according to millers, the main bran fraction. It is a source of nutritionally valuable compounds, such as dietary fibres, proteins, minerals and vitamins, that may exhibit health benefits. Despite these advantages, the aleurone layer is scarce on the market, probably due to issues related to its extraction. Many processes exist with some patents, but a choice must be made between the quality and quantity of the resulting product. Nonetheless, its potential has been studied mainly in bread and pasta. While the nutritional benefits of aleurone-rich flour addition to bread agree, opposite results have been obtained concerning its effects on end-product characteristics (namely loaf volume and sensory characteristics), thus ensuing different acceptability responses from consumers. However, the observed negative effects of aleurone-rich flour on bread dough could be reduced by subjecting it to pre- or post-extracting treatments meant to either reduce the particle size of the aleurone’s fibres or to change the conformation of its components.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient in reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures formed immediately downstream of injection location led to formation of hairpin-type vortices causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs as well. However, the increased control effectiveness for harmonic VGJs flow control strategy is attributed to the fact that shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified leading to development of large-scale coherent structures, which are very effective in increasing the momentum exchange, thus, limiting the separated region.

The Mahuagou gold deposit is among the most important gold deposits in the core of Huangling Anticline. However, the geochemical exploration on the surface of the mining area presents challenges due to the thin overburde.This paper focuses on the overburden soil of Fengxiangshugou (FXS) – Mahuanggou (MHG) section as the research object, utilizes chemical form analysis of gold, soil halogen survey, and heat-released mercury survey to determine the key deep-penetrating geochemical methods for mining area. The results indicated that Si and Al components of samples exhibit minimal variation, suggesting that drift loads did not influence the overburden soil. Based on the systematic clustering, As, Sb, Mo, Bi, W and Hg emerge as ore-body or ore-belt front elements of hydrothermal gold deposits. In the study area, the predominant chemical form of gold in soil is the strong organic bond. Compared to the total amount, strong organic bound gold and heat-released mercury show higher anomaly contrasts, making them crucial indicators of faults, intrusions and hidden ore bodies. Consequently, chemical form analysis of gold and heat-released mercury surveys can enhance the anomaly contrast, proving beneficial for geochemical prospecting for weak anomalies in this area.

The hydrodynamic results obtained from the permeability of porous materials not only affect the assessment of the stream of the gas flow through those materials but they also refer to the loss of pressure energy in that flow. The direct measure of that loss is flow resistances.The results of experimental research upon the assessment of the flow resistances of porous materials with respect to gas flow. The research conducted applied to natural materials with an anisotropic gap-porous structure. The tests were carried out on a gas permeability measuring system, adapted to different shapes of porous material samples. The process issue of the total pressure drop on a porous deposit was considered in the Reynolds number category. The coefficient of flow resistance for anisotropic materials was defined and the value of this coefficient was compared to the gas stream and the total pressure drop on the porous bed was experimentally evaluated.

The Koka gold deposit is located in the Elababu shear zone between the Nakfa terrane and the Adobha Abiy terrane, NW Eritrea. Based on the paragenetic study two main stages of gold mineralization were identified in the Koka gold deposit: 1) an early stage of pyrite-chalcopyrite-sphalerite-galena-gold-quartz vein; and 2) a second stage of pyrite-quartz veins. NaCl-aqueous inclusions, CO2-rich inclusions, and three-phase CO₂-H₂O inclusions occur in the quartz veins at Koka. The ore-bearing quartz veins formed at 268℃, from NaCl-CO₂-H₂O(-CH₄) fluids averaging 5 wt% NaCl eq. The ore-forming mechanisms include fluid immiscibility during stage I, and mixing with meteoric water during stage II. Oxygen, hydrogen and carbon isotopes suggest that the ore-forming fluids originated as mixtures of metamorphic water, meteoric water and magmatic water, whereas sulfur isotope suggest an igneous origin. Features of geology and ore-forming fluid at Koka deposit are similar to those of orogenic gold deposits, suggesting the Koka deposit might be an orogenic gold deposit related to granite.

The research field of two dimensional (2D) materials strongly relies on optical microscopy characterization tools to identify atomically thin materials and to determine their number of layers. Moreover, optical microscopy-based techniques also opened the door to study the optical properties of these nanomaterials. We present a comprehensive study of the differential reflectance spectra of 2D semiconducting transition metal dichalcogenides (TMDCs), MoS₂, MoSe₂, WS₂ and WSe₂, with thickness ranging from one layer up to six layers. We analyze the thickness-dependent energy of the different excitonic features, indicating the change in the band structure of the different TMDC materials with the number of layers. Our work provides a route to employ differential reflectance spectroscopy for determining the number of layers of MoS₂, MoSe₂, WS₂ and WSe₂.

The new mineral species oyonite, ideally Ag3Mn2Pb4Sb7As4S24, has been discovered in the Uchucchacua polymetallic deposit, Oyon district, Catajambo, Lima Department, Peru, as very rare black metallic subhedral to anhedral crystals, up to 100 μm in length, associated with orpiment, tennantite/tetrahedrite, menchettiite, and other unnamed minerals of the system Pb-Ag-Sb-Mn-As-S, in calcite matrix. Its Vickers hardness (VHN100) is 137 kg/mm2 (range 132–147). In reflected light, oyonite is weakly to moderately bireflectant and weakly pleochroic from dark grey to a dark green. Internal reflections are absent. Reflectance values for the four COM wavelengths (Rmin, Rmax (%) (λ in nm)) are: 33.9, 40.2 (471.1); 32.5, 38.9 (548.3), 31.6, 38.0 (586.6); and 29.8, 36.5 (652.3). Electron microprobe analysis gave (in wt %, average of 5 spot analyses): Cu 0.76 (2), Ag 8.39 (10), Mn 3.02 (7), Pb 24.70 (25), As 9.54 (12), Sb 28.87 (21), S 24.30 (18), total 99.58 (23). On the basis of 20 cations per formula unit, the chemical formula of oyonite is Cu0.38Ag2.48Mn1.75Pb3.79Sb7.55As4.05S24.12. The main diffraction lines are (d in Å, hkl and relative intensity): 3.34 (-312; 40), 3.29 (-520; 100), 2.920 (-132; 40), 2.821 (-232; 70), 2.045 (004; 50). The crystal structure study revealed oyonite to be monoclinic, space group P21/n, with unit-cell parameters a = 19.1806 (18), b = 12.7755 (14), c = 8.1789 (10) Å, β = 90.471 (11)°, V = 2004.1 (4) Å3, Z = 2. The crystal structure was refined to a final R1 = 0.032 for 6272 independent reflections. Oyonite belongs to the Sb-rich members of the andorite homeotypic sub-series within the lillianite homologous series. The name oyonite is after the Oyon district, Lima Department, Peru, the district where the type locality (Uchucchacua mine) is located.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

The paper proves the existence of a family of axisymmetric equilibrium figures as solutions of a stationary problem with unknown boundaries for the Navier–Stokes equations corresponding to the slow rotation of a viscous compressible two-layer liquid mass about some axis. It is assumed that the liquids are barotropic, capillary and have different viscosities, the internal fluid being bounded by a closed surface. This interface does not intersect with the external boundary of the cloud. The proof is based on implicit function theorem and carried out in the Hölder spaces.

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

The design of water Vessel fender system can minimize impact energy, which could result in severe vessel or offshore structure damage during collision. In order to protect Offshore structures and vessels from damage after impact, a Fender design approach is proposed which uses Soft materials like rubber, sand, inflated rubber tube, etc. to reduce damage on impacted vessels as well as offshore structures like wind turbines, bridges, oil drilling platforms in water etc. The fender is designed in such a way that it can handle vessels made of different material, sizes, and weights.The proposed solution is a fender consisting of a number of layers of soft sandwich materials, each layer getting softer as it moves away from the structure i.e. Hard-Soft fender design which can absorb impact energy upon collision. To handle lighter vessels made of soft or brittle materials, the outer layer is made of inflatable or Very soft foam rubber; however, the inner layer covering the offshore structure is made of hard material to handle heavy vessels made of hard material such as steel. Furthermore, the use of sand as a natural fender along waterways such as narrow channels is also proposed to reduce the cost of fender installation and catastrophic vessel impact damage on rocky ground since it produces less deformation just like rubber fender as demonstrated in the simulation. Finite Element Analysis using ANSYS software, Explicit Dynamic Autodyn, was performed. The results showed a considerable decrease in the total deformation and internal energy of the vessel and fended structure when collision occurs. Furthermore, the result showed that Hard-Soft fender layer performs much better than Soft-Hard-Soft followed by Soft-Hard Fender layer design.

Strained layer superlattice (SLS) material system is being considered for large format, small-pitch and low-cost focal plane arrays for different applications. To address difficulties associated to focal plane arrays fabrication arising from mesa-isolation etching or complex surface treatment/ passivation process, planar structures have been considered. In this work, the recent progress on planar SLS photodetector using ion-implantation for device isolation is presented. The devices are presented here are nBn and pBn heterostructure InAs/InAsSb SLS photodetector, where Zn and Si were chosen as the ion implants, respectively. The electrical and optical performance of the devices were compared along with comparison with mesa-etched device, to give deeper view of the device performance.

We investigate the flow structure and dynamics of moderate-Rayleigh-number ($Ra$) thermal convection in a two-dimensional inclined porous layer. Direct numerical simulations (DNS) confirm the emergence of $\mathit{O}(1)$ aspect-ratio large-scale convective rolls, with one `natural' roll rotating in the counterclockwise direction and one `antinatural' roll rotating in the clockwise direction. As the inclination angle $\phi$ is increased, the background mean shear flow intensifies the natural-roll motion, while suppressing the antinatural-roll motion. Moreover, our DNS reveal---for the first time in single-species porous medium convection---the existence of \emph{spatially-localized} convective states at large $\phi$, which we suggest are enabled by subcritical instability of the base state at sufficiently large inclination angles. To better understand the physics of inclined porous medium convection at different $\phi$, we numerically compute steady convective solutions using Newton iteration and then perform secondary stability analysis of these nonlinear states using Floquet theory. Our analysis indicates that the inclination of the porous layer stabilizes the boundary layers of the natural roll, but intensifies the boundary-layer instability of the antinatural roll. These results facilitate physical understanding of the large-scale cellular flows observed in the DNS at different values of $\phi$.

Dayaoshan, as an important metal ore producing area in China, is faced with the dilemma of resource depletion due to long-term exploitation. In this paper, remote sensing method is used to circle the favorable metallogenic areas and find new ore points for Gulong. Firstly, vegetation interference bas been removed by using mixed pixel decomposition method with hyperplane and genetic algorithm (GA) optimization; then, altered mineral distribution information has been extracted based on principal component analysis (PCA) and support vector machine (SVM) method; Thirdly, the favorable areas of gold mining in Gulong has been delineated by using ant colony algorithm (ACA) optimization SVM model to remove false altered minerals; Lastly, field survey verified that the extracted alteration mineralization information is correct and effective. The results show that the mineral alteration extraction method proposed in this paper has certain guiding significance for metallogenic prediction by remote sensing.

This paper describe the influence of the Rift Molango during the mineralization of elements of the platinum group and some light rare earths elements in a sedimentary exhalative ore deposit.

Passive balancing is a traditional choice for lithium-ion battery packs although it is regarded as highly inefficient. One opportunity to improve traditional balancing in sub-medium size battery packs is to combine two balancing methods: passive and active. Statistical analysis have been performed to rationalize battery pack division in smaller packs and use of higher level selective charging method to decrease losses of passive balancing. An experimental balancing prototype have been designed and tested for efficiency. Results indicate energy performance degradation if cells of the pack are with low capacity variation. Proposed balancing approach could improve performance under high cell mismatch conditions.

The newly developed friction-interlocking armor unit, called ‘Double cube’ (DC), has been designed to improve the performance of the concrete armor unit used in river/marine structures against currents/waves actions. DC unit, is an octagonal-shaped block, made up of two parts: an upper cube set on a lower base that is either square or octagonal in shape. The innovative design aims to provide a good performance in terms of stability, high tolerance placement with various contact points and ease of placement. DC’s shape and placement enhance the stability by bringing the center of gravity closer to the underlayer and providing a large contact surfaces with surrounding blocks that reduce the chance of extraction and limit movements (rocking, lifting) via "keystone" effect. The characteristics of this new unit provides a relatively high hydraulic stability number for the armor layer (NS=2.9), a favorable hydraulic performance due to energy dissipation from turbulence and aeration, as well as a high roughness coefficient (γf≈0.46) helping to reduce the overtopping.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

The aim of this paper is to present a comprehensive overview of the main aims and scopes in screening of botanicals, a task which thin-layer chromatography (TLC) is on an everyday basis confronted with and engaged in. Stunning omnipresence of this modest analytical technique (both in its standard format (TLC) and the high-performance one (HPTLC), either hyphenated or not) for many analysts might at a first glance appear chaotic and random, with an auxiliary rather than leading role in research, and not capable of issuing meaningful final statements. Based on these reflections, our purpose is not to present a general review paper on TLC in screening of botanicals, but a blueprint rather (illustrated with a selection of practical examples), which highlights a sovereign and important role of TLC in accomplishing the following analytical tasks: (i) solving puzzles related to chemotaxonomy of plants, (ii) screening a wide spectrum of biological properties of plants, (iii) providing quality control of herbal medicines and alimentary and cosmetic products of biological origin, and (iv) tracing psychoactive plants under forensic surveillance.

In this paper, we propose a lightweight physical layer aided authentication and key agreement (PL-AKA) protocol in the internet of things (IoT). Conventional evolved packet system AKA (EPS-AKA) used in long-term evolution (LTE) systems may suffer from congestions in core networks by the large signaling overhead as the number of IoT devices increases. Thus, in order to alleviate the overhead, we consider a cross-layer authentication by integrating physical layer approaches to cryptography-based schemes. To demonstrate the feasibility of the PL-AKA, universal software radio peripheral (USRP) based tests are conducted as well as numerical simulations. The proposed scheme shows a significant reduction in signaling overhead compared to the conventional EPS-AKA in both simulation and experiment. Therefore, the proposed lightweight PL-AKA has the potential for practical and efficient implementation of large-scale IoT networks.

Few-layer graphene oxide (GO) has shown none or very weak cytotoxicity and anti-proliferative effects in a wide range of cell lines such as glyoma cells and human skin HaCaT cells, in concentrations up to 100 µg/mL However, multi-layer GO has been hardly explored in the biomedical field. Thus, multi-layer GO was examined here in human keratinocyte HaCaT cells treated with different concentrations ranging from 0.01 to 150 µg/mL during different periods of times (3, 12 and 24 hours). The results of this study showed a time-concentration dependence with two non-cytotoxic concentrations (0.01 and 0.05 µg/mL) and a median effective concentration value of 4.087 µg/mL at 24 hours of GO exposure. Contrary to what has been reported for few-layer GO, cell proliferation of the HaCaT cells in contact with the multi-layer GO at 0.01 μg/mL showed identical proliferative activity compared to an epidermal growth factor (1.6-fold greater than the control group) after 96 hours. The effects of the multi-layer GO on the expression of 13 genes (SOD1, CAT, MMP1, TGFB1, GPX1, FN1, HAS2, LAMB1, LUM, CDH1, COL4A1, FBN and VCAN) at the non-cytotoxic concentrations of GO in the HaCaT cells were analyzed after 24 hours. Thus, the lowest non-cytotoxic GO concentration was able to up-regulate the CAT, TGFB1, FN1 and CDH1 genes, which confirms the great potential of multi-layer GO in the biomedical field.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.