Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

We compare two methods for creating a microfluidic device from an initial positive master with the same surface relief as the final device. The first method uses urethane or epoxy resin to create an intermediate master for PDMS casting. This method has a very low failure rate but a longer processing time. The second method utilizes PDMS double casting where the intermediate master is passivated PDMS. This method has a higher failure rate but a significantly shorter processing time. Detailed methodology for both methods is included along with a comparison of the strengths and weaknesses of each method. The resin intermediate is a simpler method while PDMS double casting is faster and more scalable. Ultimately it is found that PDMS double casting is preferable in most situations.

This research was presented the special designed microfluidic device generated for sperm separation based on assumption of different surface electrical charged of sperms X and Y. However, to avoid ethical problem, the microfluidic chip has been tested with the mimic electrical charged particles, TiO₂-coated Polystyrene beads, (TiO₂-coated Ps-beads), instead of spermatozoa. The work has been separated into three main parts. Firstly, the simply but efficient fabrication of negatively charged TiO₂-coated Ps-beads has been presented. In addition, various characterization techniques such as X-ray diffraction (XRD), Tungsten Scanning Electron Microscopy (W-SEM) with energy-dispersive X-ray spectroscopy (EDS) mode, and X-ray Absorption Spectroscopy (XAS), have been reported in this work to elucidate the reasons behind the persistence of negatively charged on the surface of TiO₂-coated Ps-beads. Results show that the fabricated TiO₂-coated Ps-beads was partly coated in the mixed forms of amorphous Ti⁴⁺ and had caused a negatively charge to appear on the surface after fabrication and had sustained its electrical charged for long. Secondly, process of simulation and fabrication of microfluidic device was presented. Finally the negatively charged TiO₂-coated Ps-beads were tested in this microfluidic devices. For design of microfluidic devices integrated with a couple of microelectrodes, the simulated structures were fabricated by photolithographic technique and tested with the Ps-beads. Percentage of validation for Ps-beads separation indicated that the 100 mm-distance-between-electrodes microfluidic device exhibits to be the highest performance prototype at 86.96%. For further confirmation, another model so called the single path prototype has been established. It is confirmed by 92.59% of validation for the utilization of the device. The successfully designed microfluidic devices can be examined with actual spermatozoa later. Furthermore, process to fabricate the negatively charged TiO₂-coated Ps-beads can be established as testified samples for development of other microfluidic devices.

The role of circulating plasma cells (CPCs) and circulating leukemic cells (CLCs) as biomarkers for several blood cancers, such as multiple myeloma and leukemia, respectively, have recently been reported. These markers can be attractive due to the minimally invasive nature of their acquisition through a blood draw (i.e., liquid biopsy) negating the need for painful bone marrow biopsies. CPCs or CLCs can be used for cellular/molecular analyses, such as immunophenotyping or fluorescence in situ hybridization (FISH). FISH, which is typically carried out on slides involving complex workflows, becomes problematic when operating on CLCs or CPCs due to their relatively modest numbers. Here, we present a microfluidic device for characterizing CPCs and CLCs enriched from peripheral blood using immunofluorescence or FISH. The microfluidic possessed an array of cross-channels (2-4 µm in depth and width) that interconnected a series of input and output fluidic channels. Placing a cover plate over the device formed microtraps, the size of which was defined by the width and depth of the cross-channels. This microfluidic chip allowed for automating immunofluorescence and FISH requiring the use of small volumes of reagents, such as antibodies and probes, as compared to slide-based immunophenotyping and FISH. In addition, the device could secure FISH results in <4 h compared to 2-3 d for conventional FISH.

Polymerase chain reaction (PCR) technique is one of the molecular methods in amplifying DNA for the detection of malaria. However, the limitations of PCR especially when used for routine clinical practice can hamper its sensitivity and specificity. With that, this study focuses on designing a microfluidic device that will mimic the function of a conventional genus-specific PCR based on 18S rRNA gene to detect malaria parasites (Plasmodium falciparum) at low grade parasitemia. The design was drawn and simulated using ANSYS 14.5 Computational Fluid Dynamics (CFD). The simulation shows that adding loops to the design increases its relative deviation but to a minimal extent as compared to having only a straight path design, which indicates that looping is acceptable in designing a microfluidic device to minimize chip length. Also, increasing the cross-sectional area of the fluid path decreases the efficiency of the design, thus, the design with a relatively smaller cross-sectional area is favored. And lastly, among the three materials utilized, the chip made of polypropylene is the most efficient with a relative deviation of 0.94 as compared to polycarbonate and polydimethylsiloxane which have relative deviations of 2.78 and 1.92, respectively.

Nanoprecipitation by liquid anti-solvent precipitation is one of the most versatile methods to produce pure drug nanoparticles (PDNPs) owing to the ability to optimize the properties of the product. Nevertheless, nanoprecipitation shows broad particle size distribution and low physical stability, leading to high batch-to-batch variability and challenging the bench-to-bedside translation. Microfluidics has emerged as a powerful tool to produce PDNPs in a simple, reproducible, and cost-effective manner with excellent control over NP size. In this work, we designed and fabricated T- and Y-shaped Si-made microfluidics device and used it to produce pure NPs of three kinase inhibitors of different lipophilicity and water-solubility, namely imatinib, dasatinib and tofacitinib, without the use of colloidal stabilizers. PDNPs display sizes in the 90-350 nm range (dynamic light scattering) and a rounded shape (high-resolution scanning electron microscopy). Analysis by X-rays diffraction and differential scanning calorimetry confirmed that this method results in highly amorphous NPs. In addition, we show that the flow rate of solvent, the anti-solvent, and the channel geometry of the device play a key role in the size of the generated NPs.

Studies on the possible association between bacteria and oral squamous cell carcinoma (OSCC) remain inconclusive, largely due to methodological variations/limitations. The objective of this study was to characterize the species composition as well as functional attributes of the bacteriome associated with OSCC. DNA obtained from 20 fresh OSCC biopsies (cases) and 20 deep-epithelium swabs (matched control subjects) were sequenced for the V1-V3 region using Illumina’s 2x300 bp chemistry. High quality, non-chimeric merged reads were classified to species level using a prioritized BLASTN-algorithm. Downstream analyses were performed using QIIME, PICRUSt, and LEfSe. Fusobacterium nucleatum subsp. polymorphum was the most significantly overrepresented species in the tumors followed by Pseudomonas aeruginosa and Campylobacter sp. Oral taxon 44, while Streptococcus mitis, Rothia mucilaginosa and Haemophilus parainfluenzae were the most significantly abundant in the controls. Functionally, genes involved in bacterial mobility, flagellar assembly, bacterial chemotaxis and LPS synthesis were enriched in the tumors while those responsible for DNA repair and combination, purine metabolism, phenylalanine, tyrosine and tryptophan biosynthesis, ribosome biogenesis and glycolysis/gluconeogenesis were significantly associated with the controls. This is the first epidemiological evidence for association of F. nucleatum and P. aeruginosa with OSCC. Functionally, an “inflammatory bacteriome” is enriched in OSSC.

This study aimed to demonstrate the potential role of Dual Energy CT in assessing Bone Mineral Density (BMD) in postmenopausal women. A retrospective study was conducted on 51 postmenopausal female patients who underwent DXA and DECT examinations for other clinical reasons. DECT images were acquired with spectral imaging using a 256-slice system. These images were processed and visualized using an HAP(fat) map. Statistical analysis was performed using the Bland-Altman method to assess agreement between DXA and DECT HAP(fat) measurements. Mean BMD, vertebral and femoral T-scores were obtained. For vertebral analysis, the Bland-Altman plot showed an inverse correlation (R2: -0.042; RMSE: 0.690) between T-scores and DECT HAP(fat) values for measurements from L1 to L4, while a good linear correlation (R2: 0.341; RMSE: 0.589) it was found for measurements at the femoral neck. In conclusion, we demonstrated the enhanced accuracy of BMD calculation through DECT, finding a statistically significant correlation only at the femoral neck where BMD results do not seem to be influenced by the overlap of the measurements on cortical and trabecular bone. This outcome could be beneficial in the future by reducing radiation exposure for patients already undergoing follow-up for chronic conditions.

Extracellular vesicles (EVs) hold enormous potential in the diagnosis and treatment of diseases, benefit from their roles in intercellular signaling, as well as their plentiful presence and stability in body fluids. However, conventional EV isolation methods are labor-intensive, and harvest EVs with low purity and compromised recovery. In addition, the drawbacks, such as limited sensitivity and specificity of traditional EV analysis methods hinder the application of EVs in clinical use. Therefore, it is urgent to develop effective and standardized methods for isolating and detecting EVs. Microfluidics technology is a powerful and rapidly developing technology that has been introduced as a potential solution for the above bottlenecks. It holds the advantages of high integration, short analysis time, low consumption of samples and reagents. In this review, we summarize the traditional techniques alongside microfluidic-based methodologies for the isolation and detection of EVs. We emphasize the separation advantages of microfluidic technology in enhancing EV capture efficiency and precise targeting, while summarizing its analytical role in targeted detection and discussing the significance of EV detection in the tumor microenvironment, providing a direction for achieving automated and high-throughput EV detection in clinical samples.

The device and method in accordance with the constant pressure regulation of micro droplet PCR in microfluidic chips are developed to explore the optimization way for the micro droplet movement, fragmentation, and bubble generation in microfluidic chips in existing digital PCR technology. In the developed device, an air source device is adopted to regulate the pressure in the chip, such that micro droplet generation and PCR amplification without bubbles can be achieved. In 3 min, the sample in 20ul will be distributed into nearly 50,000 water-in-oil droplets exhibiting a diameter of about 87μm, and the micro droplet will be subjected to a close arrangement in the chip without air bubbles. The device and chip are adopted to quantitatively detect the human gene . As indicated by the experimental results, a good linear relationship exists between detection signal and DNA concentration ranging from 101~ 105 copies /μL (R2=0.999). The micro droplet PCR devices based on constant pressure regulation chips exhibit a wide variety of advantages (e.g., achieving high pollution resistance, micro droplet fragmentation and integration avoidance, reducing human interference, and standardizing results). Thus, micro droplet PCR devices based on constant pressure regulation chips have promising applications in nucleic acid quantification.

Paper-based microfluidic analysis devices (μPADs) have attracted attention as a cost-effective platform for point-of-care testing (POCT), food safety, and environmental monitoring. Recently, three-dimensional (3D)-μPADs have been developed to improve the performance of μPADs. For accurate diagnosis of diseases, however, 3D-μPADs need to be developed to simultaneously detect multiple biomarkers. Here, we report a 3D-μPADs platform for the detection of multiple biomarkers that can be analyzed and diagnosed with a smartphone. The 3D-μPADs were fabricated using a 3D digital light processing printer and consisted of a sample reservoir (300 µL) connected to 24 detection zones (of 4 mm in diameter) through 8 microchannels (of 2 mm in width). With the smartphone application, eight different biomarkers related to various diseases were detectable in concentrations ranging from normal to abnormal conditions: glucose (0–20 mmol/L), cholesterol (0–10 mmol/L), albumin (0–7 g/dL), alkaline phosphatase (0–800 U/L), creatinine (0–500 µmol/L), aspartate aminotransferase (0–800 U/L), alanine aminotransferase (0–1000 U/L), and urea nitrogen (0–7.2 mmol/L). These results suggest that 3D-µPADs can be used as a POCT platform for simultaneous detection of multiple biomarkers.

The main contribution of this paper is to develop a graphical tool to evaluate the suitability of a candidate parametric model to fit a data set. The practical motivation is to check the adequacy of the so called SAINT model proposed in Jarner and Kryger (2011). This model has been implemented in practice by an important European pension fund concerned with setting annuity reserves for all current or former employees of Denmark. So, one particular relevant question is whether this mortality model is actually fitting old-age. Our graphical test can be described as follows. First we transform the data by means of the parametric model which is being evaluated. Should the model be correct, the transformed data will be in accordance with an Exponential distribution with rate 1. Then we construct a family of local linear hazard estimates based on the data on the transformed scale. Finally we use the statistical tool SiZer to assess the goodness-of-fit of the Exponential distribution to the data on the transformed scale. If the model is correct the SiZer map should not reveal any significant feature in the family of kernel estimates. Our method allow us to establish a diagnostic regarding the validity of the SAINT model when describing mortality patterns in four different countries.

Three-dimensional (3D) cell culture is considered more clinically relevant in mimicking the structural and physiological conditions of tumors in vivo compared to two-dimensional cell cultures. In recent years, high-throughput screening (HTS) in 3D cell arrays has been extensively used for drug discovery because of its usability and applicability. Herein, we developed a microfluidic spheroid culture device (μFSCD) with a concentration gradient generator (CGG) that enabled cells to form spheroids and grow in the presence of cancer drug gradients. The device is composed of concave microwells with several serpentine micro-channels which generate a concentration gradient. Once the colon cancer cells (HCT116) formed a single spheroid (approximately 120 μm in diameter) in each microwell, spheroids were perfused in the presence of the cancer drug gradient irinotecan for 3 days. The number of spheroids, roundness, and cell viability, were inversely proportional to the drug concentration. These results suggest that the μFSCD with a CGG has the potential to become an HTS platform for screening the efficacy of cancer drugs.

Microfluidics is facing critical challenges in the quest of miniaturizing, integrating, and automating in vitro diagnostics, including the increasing complexity of assays, the gap between the macroscale world and the microscale devices, and the diverse throughput demands in various clinical settings. Here a “3D extensible” microfluidic design paradigm that consists of a set of basic structures and unit operations was developed for constructing any application-specific assay. Four basic structures- check valve (in), check valve (out), double-check valve (in and out), and on-off valve, were designed to mimic basic acts in biochemical assays. By combining these structures linearly, a series of unit operations can be readily formed. We then proposed a “3D extensible” architecture to fulfill the needs of the function integration, the adaptive “world-to-chip” interface, and the adjustable throughput in the X, Y, and Z directions, respectively. To verify this design paradigm, we developed a fully integrated loop-mediated isothermal amplification microsystem that can directly accept swab samples and detect Chlamydia trachomatis automatically with a sensitivity one order higher than that of the conventional kit. This demonstration validated the feasibility of using this paradigm to develop integrated and automated microsystems in a less risky and more consistent manner.

Selenium is essential for the synthesis and function of various selenoenzymes, such as glutathione peroxidases, selenoprotein P, and thioredoxin reductase, which play an important role in both antioxidant defense and limiting oxidative damage. Associations between serum selenium concentration and obstetric complications as well as pregnancy outcomes has been reported in many studies. The aim of this study was to determine whether the dietary intake of selenium, its concentration in serum and the activity of glutathione peroxidase in subsequent trimesters of pregnancy affect the birth condition of newborns assessed on the basis of the Apgar score in the 1st and 5th minute of life, birth weight, body length and head and chest circumference in physiological and complicated pregnancy course. Twenty-seven pregnant women at a mean age 29.6 ± 4.8 years from the Lower Silesia region of Poland were recruited to the study, 55% of studied group had pregnancy complications. The mean reported Se intake and serum selenium content for Polish pregnant women was in the first trimester – 56.53 μg/day and 43.75 μg/l, the second trimester – 61.79 μg/day and 41.77 μg/l and the third trimester – 58.37 μg/day and 42.13 μg/l, respectively. In the subgroup of pregnant women with a physiological pregnancy course, a weak, although statistically significant, positive correlation was found in the first trimester between Se intake and the length (R=0.48, p=0.019) and birth weight of newborns (R=0.472, p=0.022), and in the second trimester with the APGAR score at 1 (R=0.680, p=0.005) and 5 minutes (R=0.55, p=0.033), as well as in the third trimester with th APGAR score at 1 minut (R=0.658, p=0.019). The GPX value had a strong positive correlation with the APGAR score at 1 min. (R=0.650, p=0.008) in the second trimester and with the birth weight of the newborns (R=0.598, p=0.039) in the third trimester. There was no correlation between newborns' birth measurements and serum selenium concentration. In the subgroup of pregnant women with pregnancy complications, a strong, statistically significant, negative correlation was found between Se intake in the second trimester and gestational age (R=-0.618, p=0.032), and in the third trimester, a positive correlation between Se concentration in serum and head circumference (R=0.587, p=0.021). The obtained results indicate that there is a relationship between the maternal selenium status during pregnancy, both in terms of the intake of this element, its serum concentration as well as the glutathione peroxidase activity, and the anthropometric parameters of the newborn, such as birth weight, length and APGAR score, especially in the group with physiological course of pregnancy, but when pregnancy complications occur, these relationships lose their importance.

Background: A new access technique was developed to reduce postoperative adverse events after the extraction of impacted maxillary wisdom teeth. Hence, this study aimed to assess the occurrence of adverse events after extraction of maxillary impacted wisdom teeth using traditional or modified access. Methods: Two different surgical incision designs were used for bilateral wisdom tooth extractions in 30 patients. The traditional incision was performed distal to the second molar in the center of the tuberosity, followed by a buccal releasing incision. After tooth extraction the wound was secured by sutures. The new technique consists of an oblique incision from the distal palatal aspect of the tuberosity towards the buccal aspect of the second molar. After tooth extraction, cyanoacrylate glue was used on the wound. Results: Lower pain was reported by patients at the site treated with the new technique (p&lt;0.01). Edema, postsurgical bleeding, and hematoma were similar in both groups. The surgical time was shorter for the new technique (p&lt;0.01). Conclusions: The new technique applied for the extraction of impacted maxillary wisdom teeth reduced postsurgical pain and the duration of surgery.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

The intracellular calcium dynamics in vascular endothelial cells (VECs) in response to wall shear stress (WSS) and/or adenosine triphosphate (ATP) have been commonly regarded as an important factor in regulating VEC function and behavior including proliferation, migration and apoptosis. However, the effects of time-varying ATP signals have been usually neglected in the past investigations in the field of VEC mechanobiology. In order to investigate the combined effects of WSS and dynamic ATP signals on the intracellular calcium dynamic in VECs, a Y-shaped microfluidic device, which can provide the cultured cells on the bottom of its mixing micro-channel with stimuli of WSS signal alone and different combinations of WSS and ATP signals in one single micro-channel, is proposed. Both numerical simulation and experimental studies verify the feasibility of its application. Cellular experimental results also suggest that a combination of WSS and ATP signals rather than a WSS signal alone might play a more significant role in VEC Ca²⁺ signal transduction induced by blood flow.

Background: The gold standard for the diagnosis of sleep bruxism (SB) and obstructive sleep apnea (OSA) is Polysmnography (PSG). At the end of the apnea episodes there is frequently a final hy-permotor muscle activity that could act as a confusion factor in the diagnosis of SB with the elec-tromyography portable devices. The aim of this study was to compare the concordance on the number of episodes of SB in a population with OSA, between the diagnosis obtained by PSG, an-alyzed manually by a neurophysiologist and that obtained manually and automatically by a portable electromyography (EMG) and electrocardiography (EKG) device. Methods: Twenty-three subjects underwent one night of polysomnographic study with simulta-neous recording with the EMG-EKG device. The variables referring to the number of episodes and the SB index measured with both tools and analyzed in the manual and automatic modes were compared. Masticatory muscle activity was scored according to published criteria. The sample was segmented by severity of OSA according to AASM criteria. ANOVA, correlations, and the Bland–Altman plot were used to quantify the agreement between both methods. The concordance was calculated through the ICC. Results: The total events of SB per night in the PSG study were on average (8.17), lower than the one obtained with EMG-EKG manual analysis (14.13) and automatic (29.26). Both the SB PSG and Manual EMG-EKG episodes decrease from non-OSA (PSG = 16 ± 13,55, EMG-EKG = 16,83 ±11,58) to severe OSA (PSG = 3,14 ± 4,26, EMG-EKG = 9,86 ± 8,09). However, in the case of automatic EMG-EKG mode: the number of SB episodes in severe OSA doubled (41,23 ± 12,50) with respect to non OSA (24,50 ± 12,19). On average: the EMG-EKG device Automatic analysis measures 21.08 units more than PSG. The results with the manual EMG-EKG analysis improved. Conclusion: There is no concordance between the results obtained in the PSG neurophysiologic analysis and those obtained by means of the EMG-EKG device automatic and manual analysis for the diagnosis of SB in a population mostly with OSA. The OSA could act as a confusion factor in the diagnosis of SB with the electromyography portable devices, but further study is needed.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Background: Peritoneal sclerosis (PS) and its most severe form, encapsulating PS (EPS), are rare entities that can occur in various procedures (liver transplantation, intraperitoneal chemotherapy), secondary to medications ( beta-blockers); however, PS or EPS typically occur in patients undergoing peritoneal dialysis as a form of renal function substitution. Medical or surgical treatments can be applied, but morbidity and mortality have high rates . This condition typically presents clinically as an intestinal obstruction caused by the inclusion of the intestinal loops in the peritoneal fibrous membrane. Methods: Herein we present data from a single tertiary surgery center that has dedicated teams for patients receiving dialysis. In 12 years we analyzed a group of 63 patients admitted for catheter replacement/removal or for acute surgical pathology. In 5 cases (7,9%) we diagnosed EPS . Two patients with EPS presented with atypical abdominal pathologies requiring emergency surgery: one case of hemoperitoneum caused by a ruptured ovarian cyst and one case of uterine fibroids and metrorrhagia. Results: The definitive diagnoses were established intraoperatively and by analyzing the morpho-pathological changes of the peritoneum. The possible intraoperative challenges included laborious dissection, difficulties in restoring the correct anatomical landmarks, increased duration of the surgical intervention and a high rate of incidents and accidents Conclusions: The aim of the present study was to emphasize the possibility of other surgical pathologies overlapping with EPS, increasing the complexity of the surgical intervention. Also, we sought to determine whether there is a correlation between the morpho-pathological results of these patients who underwent emergency surgery and the common EPS morpho-pathological changes.

Osteoporosis (OP), a prevalent skeletal disorder characterized by compromised bone strength and increased susceptibility to fractures, poses a significant public health concern. This review aims to provide a comprehensive analysis of the current state of research in the field, focusing on the application of proteomic techniques to elucidate diagnostic markers and therapeutic targets for OP. The integration of cutting-edge proteomic technologies has enabled the identification and quantification of proteins associated with bone metabolism, leading to a deeper understanding of the molecular mechanisms underlying OP. In this review, we systematically examine recent advancements in proteomic studies related to OP, emphasizing the identification of potential biomarkers for OP diagnosis and the discovery of novel therapeutic targets. Additionally, we discuss the challenges and future directions in the field, highlighting the potential impact of proteomic research in transforming the landscape of OP diagnosis and treatment.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Nowadays, microfluidics has become an anarchist interdisciplinary topic with considerable attention in a wide range of biotechnology applications. In this research work, numerical investigation of microfluidic micro-mixer is carried out using hybrid actuation approach with different micropillar shapes and gaps. For this purpose, COMSOL Multiphysics is used with three different physics such as thermoviscous acoustic to solve acoustic governing equations, laminar physics is used to solve fluid flow governing equations and diluted transport species is used to solve mixing governing equations. The simulations were carried out with flow velocity of 200 µm/s at both inlets with an oscillation frequency of 15kHz. The outcomes were in the form of acoustic characteristics such as acoustic pressure, acoustic velocity, acoustic streaming and mixing index. The results revealed that the inclusion of micropillars enhanced the mixing performance and strength of acoustic field resulting in improvement of mixing performance compared to the case without micropillars. In addition, it was also investigated that blade shape micropillars with 0.150 mm gaps deliver best results compared to the other cases with maximum and minimum values of the mixing index 0.95 and 0.72 respectively. The obtained results can be extremely helpful for design and modifications of hybrid microfluidics micro-mixer.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P&lt;0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Microscale surgery on single cells and small organisms have enabled major advances in fundamental biology and in engineering biological systems. Examples of applications range from wound healing and regeneration studies to the generation of hybridoma to produce monoclonal antibodies. Even today, these surgical operations are often performed manually, but they are labor-intensive and lack reproducibility. Microfluidics has emerged as a powerful technology to control and manipulate cells and multicellular systems at the micro- and nanoscale with high precision. Here, we review the physical and chemical mechanisms of microscale surgery, and the corresponding design principles, applications, and implementations in microfluidic systems. We consider four types of surgical operations: 1) Sectioning, which splits a biological entity into multiple parts, 2) ablation, which destroys part of an entity, 3) biopsy, which extracts materials from within a living cell, and 4) fusion, which joins multiple entities into one. For each type of surgery, we summarize the motivating applications and the microfluidic devices developed. Throughout the review, we highlight existing challenges and opportunities. We hope that this review will inspire scientists and engineers to continue to explore and improve microfluidic surgical methods.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

Postprandial glucose levels between 4 and 7.9 hours (PPG4–7.9h) correlate with mortality from various diseases including hypertension, diabetes, cardiovascular disease, and cancer. This study aimed to assess if predicted PPG4–7.9h could diagnose diabetes. Two groups of participants were involved: Group 1 (4420 participants) had actual PPG4–7.9h, while Group 2 (8422 participants) lacked this measure but had all the diabetes diagnostic measures. Group 1 underwent multiple linear regression to predict PPG4–7.9h using 30 predictors, achieving accuracy within 11.1 mg/dL in 80% of the participants. Group 2 had PPG4–7.9h predicted using this model. Receiver operating characteristic curve analysis showed that predicted PPG4–7.9h could diagnose diabetes with an accuracy of 87.3% in Group 2, with a sensitivity of 75.1% and specificity of 84.1% at the optimal cutoff of 102.5 mg/dL. Simulation on 10,000 random samples from Group 2 revealed that 175 participants may be needed to investigate PPG4–7.9h as a diabetes diagnostic marker with a power of at least 80%. In conclusion, predicted PPG4–7.9h appears to be a promising diagnostic indicator for diabetes. Future studies seeking to ascertain its definitive diagnostic value might require a minimum sample size of 175 participants.

In Brazil, Brazilian borreliosis (BB), characterized molecularly, exhibits symptoms akin to Lyme disease (LD) but presents unique epidemiological, clinical, and morphological features. This study explores the incidence, diagnostic challenges, and awareness initiatives regarding this disease in Brazil. Employing a narrative review methodology, data were sourced from Pubmed, Ebsco, Google Scholar, and Web of Science without temporal constraints. Results reveal diagnostic complexities in Brazil due to the low sensitivity of conventional tests and the use of North American B. burgdorferi antigens. Despite challenges, epidemiological studies indicate an upswing in cases in humans and animals. Therefore, there is an urgent need to define new biomarkers, molecular strategies, or new antigenic targets to advance the development of vaccines and diagnostics. Early and accurate pathogen identification is crucial for active surveillance to comprehend and manage this zoonosis.

While laminar flow heat transfer and mixing in microfluidic geometries has been investigated experimentally, as has the effect of geometry-induced turbulence in microfluidic flow (it is well documented that turbulence increases convective heat transfer in macrofluidic flow), little literature exists investigating the effect of electrokinetically-induced turbulence on heat transfer at the micro scale. Using recently observed experimental data, this work employed computational fluid dynamics coupled with electromagnetic simulations to determine if electrokinetically-forced, low-Reynolds number turbulence could be observed in a rectangular microchannel with using Newtonian fluids. Analysis of the results was done via comparison to the experimental criteria defined for turbulent flow. This work shows that, even with a simplified simulation setup, computational fluid dynamics (CFD) software can produce results comparable to experimental observations of low-Reynolds turbulence in microchannels using Newtonian fluids. In addition to comparing simulated velocities and turbulent energies to experimental data this work also presents initial data on the effects of electrokinetic forcing on microfluidic flow based on entropy generation rates.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

In chronic myeloid leukemia (CML), a clonal proliferative disorder of granulocytic lineage, the 90%‐95% of cases are characterized by t(9;22) (q34.1;q11.2) translocation, leading to the Philadelphia chromosome (1). Rarely, CML patients directly present a blast crisis, mostly of myeloid origin (2, 3). Herein, we describe one rare CML case, showing an unusual early T lymphoid blastic crisis.

Despite available global efforts and funding, Tuberculosis (TB) continues to affect a considerable number of patients worldwide. Policy makers and stakeholders set clear goals to reduce TB incidence and mortality, but the emergence of multidrug-resistant TB (MDR-TB) and extensively drug-resistant TB (XDR-TB) complicate the reach of these goals. Drug-resistance TB needs to be diagnosed rapidly and accurately to effectively treat patients, prevent the transmission of MDR-TB, minimise mortality, reduce treatment costs and avoid unnecessary hospitalisations. In this narrative review, we provide a comprehensive overview of laboratory methods for detecting drug resistance in MTB, focusing on phenotypic, molecular and other drug susceptibility testing (DST) techniques. We found a large variety of methods used, with the BACTEC MGIT 960 being the most common phenotypic DST and the Xpert MTB/RIF being the most common molecular DST. We emphasise the importance of integrating phenotypic and molecular DST to address issues like resistance to new drugs, heteroresistance, mixed infections and low-level resistance mutations. Notably, most of the analysed studies adhered to the outdated definition of XDR-TB and did not consider the pre-XDR definition, thus posing challenges in aligning diagnostic methods with the current landscape of TB resistance.

Dipeptidyl peptidase 9 (DPP9) is a multifunctional intracellular protease with roles in tumour growth, inflammation and mitochondrial function. We developed a hepatocyte-specific DPP9 knockout mouse (DPP9-KO) to explore DPP9 in a mouse model of hepatocellular carcinoma (HCC). DPP9-KO mice were generated by crossing Albumin-Cre mice (Wt/Wt Cre+/+) with DPP9 floxed mice (Fl/Fl Cre-/-). Mice were treated with Diethylnitrosamine and Thioacetamide then an atherogenic High Fat Diet until 28 weeks of age. DPP9-KO mice had reduced liver and subcuta-neous adipose tissue mass and lower fasting plasma glucose, fewer small macroscopic liver nod-ules compared to DPP9-WT mice. However, there were no differences in the total number of mac-roscopic liver nodules, tumour burden, inflammation score and steatosis score. Consistent with the known ability of DPP9 to suppress NLRP1 activation, activated caspase-1 protein was ele-vated in DPP9-KO mouse liver. Additionally, Nfkbib, Cxcl10 and Ccl5 mRNA and protein levels of autophagy marker beclin1 and tumour suppressor p53 were increased. In conclusion, DPP9 de-pletion in hepatocytes may reduce liver cancer initiation, via mechanisms that may include in-creased autophagy and innate tumour suppression in this experimental model. Finally, the data supports DPP9 having a role in glucose regulation by the liver.

Hyperplastic nodules (HNs) are benign polypoid lesions of the colorectal mucosa reportedly caused by hyperplasia of the crypt epithelial cells. They differ from hyperplastic polyps because the crypts do not have histologically serrated changes. HNs often occur in the rectal mucosa and tend to be multifocal. We have proposed a new colitis nucleomigrans (CN) concept as the third type of microscopic colitis. Our histopathological criteria of CN include: i) chained nuclear migration to the middle part of the surface-lining columnar epithelium, ii) apoptotic nuclear debris scattered in the eosinophilic cytoplasm underneath the nuclei, and iii) mild to moderate chronic inflammation in the lamina propria. Immunostaining for cleaved-caspase 3 revealed apoptotic bodies. In this study, we report that most HN lesions share the histological features with CN, representing polypoid CN. We evaluated 108 lesions of HN in total, and 94 (87%) were reclassified as polypoid CN. In the polypoid CN, the lamina propria mucosae were uniformly edematous, suggesting that accelerated apoptosis of the mucosal surface epithelium may cause osmotic dysregulation to form localized mucosal elevations.

The up-and-coming microfluidic technology is the most promising platform for designing anti-cancer drugs and new point-of-care diagnostics. Compared to conventional drug screening methods based on Petri dishes and animal studies, drug delivery in microfluidic systems has many advantages. For instance, these platforms offer high throughput drug screening, require a small amount of samples, provide an in vivo-like microenvironment for cells, and eliminate ethical issues associated with animal studies. Multiple cell cultures in microfluidic chips could better mimic the 3D tumor environment using low reagents consumption. The clinical experiments have shown that combinatorial drug treatments have a better therapeutic effect than monodrug therapy. So many attempts were performed in this field in the last decade. This review highlights the applications of microfluidic chips in anti-cancer drug screening and systematically categorizes these systems as a function of sample size and combination of drug screening. Finally, it provides a perspective on the future of the clinical applications of microfluidic systems for anti-cancer drug development.

This article provides a systematic review of the crosslinking strategies used to produce microgel particles in microfluidic chips. Various ionic crosslinking methods for gelation of charged pol-ymers are discussed, including external gelation via crosslinkers dissolved or dispersed in the oil phase, internal gelation methods using crosslinkers added to the dispersed phase in their non-active forms, such as chelating agents, photo-acid generators, sparingly soluble or slowly hydrolyzing compounds, and methods involving competitive ligand exchange, rapid mixing of polymer and crosslinking streams, and merging polymer and crosslinker droplets. Covalent crosslinking methods using enzymatic oxidation of modified biopolymers, photo-polymerization of crosslinkable monomers or polymers, and thiol-ene “click” reactions are also discussed, as well as the methods based on sol-gel transitions of stimuli responsive polymers triggered by pH or temperature change. In addition to homogeneous microgel particles, the production of structurally heterogeneous particles such as composite hydrogel particles entrapping droplet interface bi-layers, core-shell particles, organoids, and Janus particles are also discussed. Microfluidics offers the ability to precisely tune chemical composition, size, shape, surface morphology, and internal structure of microgels by bringing in contact multiple fluid streams in a highly controlled fashion using versatile channel geometries and flow configurations and allowing controlled crosslinking.

Micro-technology has played a substantial role in bioscience, biomedical and biotechnological research due to its core advantages in modern science and engineering. It has created unique development in various sectors of bio-research and upsurges the efficacy of research at the molecular level in recent years. Microfluidic technology makes it possible to manipulate sample volumes at the micro- and nano-level (called nanofluidics) with terrific control outside in vivo cellular microenvironment, enabling the reduction of discrepancies between in vivo and in vitro environments as well as reducing reaction time and cost. In this review, we discuss various effective integrations of microfluidic technologies into biotechnology and its paradigmatic significance in bio-research, supporting mechanical and chemical in vitro cellular micro-environment. Specific innovations relating to the application of microfluidics to advance microbial life, solitary and co-cultures along with a multiple-type cell culturing, cellular communications, cellular interactions and population dynamics are discussed.

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

Inflammation plays a key role in the induction of choroidal neovascularization (CNV). Inflammatory choroidal neovascularization (iCNV) is a severe but uncommon complication of both infectious and non-infectious uveitides. It is hypothesized that its pathogenesis is similar to that of wet age-related macular degeneration (AMD), and involves hypoxia as well as the release of vascular endothelial growth factor, stromal cell-derived factor 1-alpha, and other mediators. Inflammatory CNV develops when inflammation or infection directly involves the retinal pigment epithelium (RPE)–Bruch’s membrane complex. Inflammation itself can compromise perfusion, generating a gradient of retinal-choroidal hypoxia that additionally promotes the formation of choroidal neovascularization in the course of uveitis. The development of choroidal neovascularization is extremely common in conditions such as punctate inner choroidopathy, multifocal choroiditis, serpiginous choroiditis, and presumed ocular histoplasmosis syndrome. Although the majority of iCNV cases are well defined and appear as the “classic” type on fluorescein angiography, the diagnosis of iCNV is challenging due to difficulties in differentiating between inflammatory choroiditis lesions and choroidal neovascularization. Modern multimodal imaging, particularly the recently introduced technology of optical coherence tomography (OCT) and OCT angiography (noninvasive and rapid imaging modalities) can reveal additional features that aid the diagnosis of iCNV. However, more studies are needed to establish their role in the diagnosis and evaluation of iCNV activity. Keywords: uveitis; inflammatory choroidal neovascularization; multimodal imaging; fluorescein angiography; indocyanine green angiography; optical coherence tomography; optical coherence tomography angiography; near-infrared autofluorescence

Introduction Blunt carotid injuries (BCI) in pediatric trauma are quite rare. Due to the low number of cases, only a few reports and studies have been conducted on this topic. This review will discuss how frequent BCI/ BCVI on pediatric patients after blunt trauma is, what routine diagnostics look like, if a CT/ CTA scan on pediatric patients after blunt trauma is always necessary and if there are any negative health effects? Methods This literature review includes reviews, systematic reviews, case reports and original studies in english language between 1999 and 2020 that have dealt with pediatric blunt trauma and the diagnostics of BCI and BCVI. Furthermore, publications on the risk of radiation exposure on children were included in the study. For literature research, Medline (PubMed) and the Cochrane library were used. Results Pediatric BCI/ BCVI, shows an overall incidence between 0.03 – 0.5% of confirmed BCI/ BCVI cases due to pediatric blunt trauma. 1.1 – 3.5% of pediatric blunt trauma patients underwent CTA to detect BCI. Only 0.17 – 1.2% of all CTA scans shows a positive diagnosis for BCI. In children, the median volume CT dose index on a non-contrast head CT is 33 milligray, a computed tomography angiography needs at least 138 mGy. A cumulative doses of about 50 mGy almost triples the risk of leukemia, and doses of about 60 mGy triples the risk of brain cancer. Discussion Knowing that a BCI could have extensive neurologic consequences for children, it is necessary to evaluate routine pediatric diagnostics after blunt trauma. Computed tomography scans (CT) and computed tomography angiography (CTA) are mostly used in routine BCI diagnostics. However, since radiation exposure in children should be as low as reasonably achievable, it should be asked if other diagnostic methods could be used to identify risk groups. Trauma guidelines and clinical scores like the McGovern score are reflect established BCI screening options, as well as using duplex ultrasound.

Although mammography has been the gold standard for early detection of breast cancer, if a woman has dense breast tissue, a false negative diagnosis may occur. Breast ultrasound, whether hand-held or automated, is a useful adjunct to mammography but adds extra time and cost. The primary aim was to demonstrate that our second-generation Aceso system, which combines full-field digital mammography (FFDM) and automated breast ultrasound (ABUS) in a single platform, is able to produce improved quality images that provide clinically meaningful results. Aceso was first tested using two industry standards: a CDMAM phantom to assess the FFDM images; and the CIRS 054GS phantom to evaluate the ABUS images. In addition, 25 women participated in a clinical trial: 14 were healthy volunteers while 11 were patients referred by the breast clinic at Groote Schuur Hospital. The CDMAM phantom results showed the FFDM results were better than EUREF’s standard of “acceptable” and were approaching “achievable”. The ABUS results showed lateral and axial spatial resolution of 0.5 mm and adequate depth penetration of 80 mm. Our second-generation Aceso system, with its improved quality of clinical FFDM and ABUS images, has demonstrated its potential for early detection of breast cancer in a busy clinic.

In the last decade, three-dimensional (3D) printing has allowed the field of complex microfluidic channels to expand rapidly towards channels with variable cross-sections (i.e., beyond simple rounded media with a constant diameter) and channels. Whose trajectory can be outside a single plane and has gained numerous macro- and nanoscale manufacturing advances. Three-dimensional printing is being explored for various biomedical applications and the fabrication of nanomedicines using additive manufacturing techniques. Employing 3D-printed templates for macro-to-micro interfacing, a passively operated microfluidic device was designed. The research seeks to fabricate a biodevice that enables insulin microdosing, creating a subsystem like a microvalve and a microchannel matrix using additive manufacturing techniques. Our systems feature designs that enhance fluid dynamics without affecting the stability of the insulin. We propose using Humalog insulin in tropical climates (up to 30°C) without refrigeration for 28 days. The microvalve has a spiral trajectory with four outlet channels distributed along it. These channels align with the microchannels organized in a 10 mm x 15 mm matrix with 25 microchannels, each with a 770 µm internal diameter. The system delivers a dose of 2,3 mL in 6 minutes. We designed these systems for insulin micro-dosing, but they can also serve similar devices for other drugs.

In recent years, the field of drug delivery has seen a significant shift towards the exploration and utilisation of nanoparticles (NPs) as versatile carriers for therapeutic agents. With its ability to provide exact control over NPs' characteristics, microfluidics has emerged as a potent platform for the efficient and controlled synthesis of NPs. Microfluidic devices designed for precise fluid ma-nipulation at the micro-scale offer a unique platform for tailoring NP properties, enabling en-hanced control over NP properties such as size, morphology and size distribution while ensuring high batch-to-batch reproducibility. Microfluidics can be used to produce liposomes, solid lipid nanoparticles, polymer-based NPs and lipid-polymer hybrid NPs, as well as a variety of inorganic NPs such as silica, metal, metal oxide, quantum dots and carbon-based NPs, offering precise control over composition and surface properties. Its unique precision in tailoring NP properties holds great promise for advancing NP-based drug delivery systems in both clinical and industrial set-tings. Although challenges with large-scale production still remain, microfluidics offers a trans-formative approach to NP synthesis. In this review, starting from the historical development of microfluidic systems, the materials used to create the systems, microfabrication methods and system components will be discussed in order to provide the reader with an overview of micro-fluidic systems. In the following, studies on the fabrication of nanoparticles such as lipid NPs, polymeric NPs and inorganic NPs in microfluidic devices are included.

It is increasingly common for experiments in biology and medicine to involve large numbers of hypothesis tests. A natural graphical method for visualizing these tests is to construct a histogram from the p-values of these tests. In this article, we examine the shapes, both normal and abnormal, that these histograms can take on, as well as present simple inferential procedures that help to interpret the shapes in terms of diagnosing potential problems with the experiment. We examine potential causes of these problems in detail, and discuss potential remedies. Throughout, examples of abnormal-looking p-value histograms are provided and based on case studies involving real biological experiments.

Tuberculosis (TB) remains a global health threat, necessitating innovative strategies for control and prevention. This comprehensive review explores the Mycobacterium tuberculosis Lysine Exporter (LysE) gene, unveiling its multifaceted roles and potential uses in controlling and preventing tuberculosis (TB). As a pivotal player in eliminating excess L-lysine and L-arginine, LysE contributes to the survival and virulence of M. tuberculosis. This review synthesizes findings from different electronic databases and includes 13 studies focused on the LysE of M. tuberculosis. The research unveils that LysE can be a potential drug target, a diagnostic marker for TB, and a promising candidate for vaccine development. The absence of LysE in the widely used BCG vaccine underscores its uniqueness and positions it as a novel area for TB prevention. In conclusion, this review underscores the significance of LysE in TB pathogenesis and its potential as a drug target, diagnostic marker, and vaccine candidate. The multifaceted nature of LysE positions it at the forefront of innovative approaches to combat TB, calling for sustained research efforts to harness its full potential in the global fight against this infectious disease.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Introduction: The repertoire of microRNAs (miRNAs) in thyroid carcinomas starts to be elucidated. Among differentiated thyroid carcinomas (DTC), papillary thyroid carcinoma (PTC) is the most common. The assessment of miRNAs expression may contribute to refine the pre-surgical diagnosis, in order to obtain a personalized and more effective treatment of patients. Aims: This study aims to evaluated 1) miRNAs expression in a series of DTC, and the association with the presence of selected genetic mutations, in order to improve diagnosis and predict biologic behavior of DTC/PTC. 2) the reliability of molecular tests in Ultrasound-guided Fine Needle Aspiration Cytology (US-FNAC) for a more precise preoperative diagnosis. Material and methods: This series includes 176 samples (98 cytology samples and 78 formalin-fixed paraffin embedded (FFPE) tissues) obtained from 106 patients submitted to surgery, being 13 benign lesions (controls) and 93 DTCs (cases). The microRNA expression was assessed for miR-146b, miR-221, miR-222, and miR-15a by quantitative reverse transcriptase-polymerase chain reaction (qRT-PCR) and the results were analyzed using the 2- ΔΔCT method, using miR16 as an endogenous control. The discriminative ability of miRNAs expression regarding PTC diagnosis was evaluated using the area under the Receiver Operating Characteristic Curve (AUC). The association of miRNAs expression, clinicopatological features and genetic alterations (BRAF, RAS and TERTp) was evaluated in PTCs. Results/Discussion: All the analyzed miRNAs showed a tendency to be over expressed in DTCs/PTCs when compared with benign lesions, both in cytology and histology samples. In cytology, miRNAs expression levels were higher in malignant than in benign tumors. In histology, corresponding discriminative abilities regarding PTC diagnosis were: miR-146b (AUC0.94, 95%CI 0.87-1), miR-221 (AUC0.79, 95%CI 0.68-0.9), miR-222 (AUC0.76, 95%CI 0.63-0.89) and miR-15a (AUC0.85, 95%CI 0.74-0.97). miR-146b showed 89% sensitivity (se) and 87% specificity (sp); mi-R221 se=68.4, sp=90; miR222 se=73, sp=70, and mi-R15a se=72, sp=80. MicroRNAs were associated with aggressive clinicopathological features and tumor progression in PTCs (p &lt; 0.05), particularly for miR-222. Our data reveals a significant association between higher expression levels of miR-146b, miR-221 and miR-222, with the presence of BRAF mutation (p&lt;0.001), and miR-146b (p=0.016) and miR-221 (p=0.010) with the presence of RAS mutation, suggesting an interplay of these mutations with miRNAs expression. Although this study has a relatively small sample size, over expression of miRNAs in cytology may contribute to a more precise preoperative diagnosis. The miRNAs showed a good discriminative ability in PTC diagnosis. The association between the miRNAs expression profile and genetic alterations results could be useful for an accurate diagnosis of DTCs/PTCs in FNAC.

Cutaneous wound healing is a complex multi-stage process involving direct and indirect cell communication events with the aim of efficiently restoring the barrier function of the skin. One key aspect in cutaneous wound healing is associated with cell movement and migration into the physically, chemically and biologically injured area resulting in wound closure. Understanding the conditions under which cell migration is impaired and elucidating the cellular and molecular mechanisms that improve healing dynamics is therefore crucial in devising novel therapeutic strategies to elevate patient suffering, reduce scaring and eliminate chronic wounds. Following the global trend towards automation, miniaturization and integration of cell-based assays into microphysiological systems, conventional wound healing assays such as the scratch assay or cell exclusion assay have recently been translated and improved using microfluidics and lab-on-a-chip technologies. These miniaturized cell analysis systems allow precise spatial and temporal control over a range of dynamic microenvironmental factors including shear stress, biochemical and oxygen gradients to create more reliable in vitro models that resemble the in vivo microenvironment of a wound more closely on a molecular, cellular, and tissue level. The current review provides (a) an overview on the main molecular and cellular processes that take place during wound healing, (b) a brief introduction into conventional in vitro wound healing assays, and (c) a perspective on future cutaneous and vascular wound healing research using microfluidic technology.

Conventional diagnostic techniques are based on utilization of analyte sampling, sensing and signalling on separate platforms for detection purposes, that must be evaded and integrated to a single step procedure in point of care (POC) testing devices. Therefore, the trend has been shifted towards utilization of microfluidic platforms for detection of analytes in biochemical, clinical and food technology due to its being expeditious. Microfluidic systems moulded with polymer substances or glass offer specific and sensitive detection of infectious and non-infectious diseases by providing innumerable benefits including less cost, good biological affinity, strong capillary action and simple process of fabrication. In the case of nucleic acid-based nanosensors, there are some challenges that need to be addressed such as cellular lysis, isolation and amplification of nucleic acid required to be accomplished prior to its detection. To avoid utilization of laborious steps for executing these steps, advances have been deployed in this perspective for on-chip sample preparation, amplification and detection which not only improves sensitivity and selectivity but also saves time and resources. This review emphasizes the significance of microfluidic technology for nucleic acid detection of infectious and non-infectious diseases. The implementation of isothermal amplification in concomitance with lateral flow assay greatly increases the binding efficiency of nanoparticles and biomolecules, improves limit of detection and sensitivity. Most importantly deployment of paper-based material made of cellulose reduces the overall cost. Microfluidic technology in nucleic acid testing has been discussed by explicating its applications in different fields. This review concludes with the prospects and proposes future directions in microfluidic based methods in disease diagnosis.

89Zr-radiolabelled proteins functionalised with desferrioxamine B are a cornerstone of diagnostic positron emission tomography. In the clinical setting, 89Zr-labelled proteins are produced manually. Here, we explore the potential of using a microfluidic photochemical flow reactor to prepare 89Zr-radiolabelled proteins. The light-induced functionalisation and 89Zr-radiolabelling of human serum albumin ([89Zr]ZrDFO-PEG3-Et-azepin-HSA) was achieved by flow photochemistry with a decay-corrected radiochemical yield (RCY) of 31.2±1.3% (n = 3) and radiochemical purity &gt;90%. In comparison, a manual batch photoreactor synthesis produced the same radiotracer in a decay-corrected RCY of 59.6±3.6% (n = 3) with an equivalent RCP &gt;90%. The results indicate that photoradiolabelling in flow is a feasible platform for the automated production of protein-based 89Zr-radiotracers, but further refinement of the apparatus, and optimisation of the method is required before the flow process is competitive with manual reactions.

The inherent trace quantity of primary fatty acid amides found in biological systems presents challenges for analytical analysis and quantitation, requiring a highly sensitive detection system. The use of microfluidics provides a green sample preparation and analysis technique through small-volume fluidic flow through micron-sized channels embedded in a PDMS device. Microfluidics provides the potential of having a micro total analysis system where chromatographic separation, fluorescent tagging reactions, and detection are accomplished with no added sample handling. This study describes the development and optimization of a microfluidic-laser indued fluorescence (LIF) analysis and detection system that can be used for the detection of ultra-trace levels of fluorescently tagged primary fatty acid amines. A PDMS microfluidic device was designed and fabricated to incorporate droplet-based flow. Droplet microfluidics have enabled on-chip fluorescent tagging reactions to be performed quickly and efficiently, with no additional sample handling. An optimized LIF optical detection system provided fluorescently tagged primary fatty acid amine detection sub-fmol (436 amol) LODs. The use of this LIF detection provides unparalleled sensitivity, with detection limits several orders of magnitude lower than currently employed LC-MS techniques and might be easily adapted for use as a complementary quantification platform for parallel MS-based -omics studies.

Cardiac amyloidosis is caused by amyloid fibrils that deposit in the myocardial interstitium, causing restrictive cardiomyopathy and eventually death. The electromechanical, inflammatory, and autonomic changes due to amyloid deposition result in arrhythmias. Atrial fibrillation is by far the most common arrhythmia. Rate control strategy is generally poorly tolerated due to restrictive filling physiology and heart rate dependance, favoring adoption of rhythm control strategy. Anticoagulation for stroke prophylaxis is warranted irrespective of CHA2DS2Vasc score in patients with favorable bleeding profile; data on left appendage closure devices is still insufficient. Ventricular arrhythmias are also not uncommon and the role of implantable cardioverter-defibrillator in cardiac amyloidosis is controversial. There is no evidence of improvement in outcomes when used for primary prevention in these patients. Bradyarrhythmia is most commonly associated with sudden cardiac death in cardiac amyloidosis. Pacemaker implantation can help provide symptomatic relief but does not confer mortality benefit.

This paper presents a novel framework for Collaborative Learning Networks (CLNs) in classrooms, aiming to optimize resource utilization and enhance educational services. The study addresses the inefficiencies of traditional education models, particularly the underutilization of computational resources and limited access to specialized software. The proposed framework employs a mix of task-based and random allocation strategies to distribute computational tasks within the CLN, considering each device’s capabilities and task requirements. The findings show significant improvement in resource utilization, facilitated by device-to-device collaboration and task sharing, thus enriching students’ learning experiences. This work contributes to optimizing resource utilization in education, advancing the field of CLNs.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.

Over the last two decades, microfluidics has received significant attention from both academia and industry, and researchers report thousands of new prototype devices each year for use in a broad range of environmental, pharmaceutical, and biomedical engineering applications. While lab-on-a-chip fabrication costs have continued to decrease, the hardware required for monitoring fluid flows within microfluidic devices themselves remains expensive and often cost prohibitive for researchers interested in starting a microfluidics project. As microfluidic devices become capable of handling complex fluidic systems, low-cost, precise and real time pressure and flow rate measurement capabilities has become increasingly important. While many labs use commercial platforms and sensor, these solutions can often cost thousands of dollars and can be too bulky for on-chip use. Here we present a new inexpensive and easy -to-use piezoresistive pressure and flow sensor that can be easily integrated into existing on-chip microfluidic channels. The sensor consists of PDMS-Carbon black conductive membranes and uses an impedance analyzer to measure impedance change due fluid pressure. The sensor costs several orders of magnitude less than existing commercial platforms and can monitor local fluid pressures and calculate flow rates based on pressure gradient.

Analyzing the cells in various body fluids can greatly deepen the understanding of the mechanisms governing the cellular physiology. Because of the variability of physiological and metabolic states, it is important to be able to perform such studies on individual cells. Therefore, we developed an optofluidic system in which we precisely manipulated and monitored individual cells of Escherichia coli. We used laser tweezers Raman spectroscopy (LTRS) in a microchamber chip to manipulate and analyze individual E. coli cells. We subjected the cells to antibiotic cefotaxime, and we observed the changes by the time-lapse microscopy and Raman spectroscopy. We found observable changes in the cellular morphology (cell elongation) and in Raman spectra, which were consistent with other recently published observations. We tested the capabilities of the optofluidic system and found it to be a reliable and versatile solution for this class of microbiological experiments.

Layered halide perovskites have emerged as a promising contender in solid-state lighting thanks to their tunable bandgap, high luminescence quantum yield, and high color purity. However, the fabrication of perovskite light-emitting devices in laboratories usually experiences low de-vice-to-device reproducibility since perovskite crystallization is highly sensitive to ambient condi-tions, such as humidity and temperature. Although device processing inside gloveboxes is primarily used to reduce the influence of oxygen and moisture, several extraneous variables, including gas-eous pollution traces and thermal fluctuations in the inert atmosphere or contaminations from re-sidual solvents confined in the enclosed environment, can destabilize the crystallization process and alter the properties of the emissive layers. Here, we examine different experimental set-ups for spin-coating deposition of layered perovskites in inert atmospheres and their influences on the formation of polycrystalline thin films. Our results demonstrate that fluctuations in the glovebox properties (concentrations of residual O2 and H2O or solvent traces), even in very short timescales, can negatively impact the consistency of the perovskite film formation, while thermal variation plays a relatively minor role in this phenomenon. Furthermore, careful storage of chemical species inside the workstation is critical for reproducing high-quality perovskite layers. Consequently, when applying our most controlled environment for perovskite deposition, the photoluminescence life-time of perovskite thin films shows a standard deviation of only 3%, whereas the reference set-up yields a 15% standard deviation. Regarding complete perovskite light-emitting diodes, the uncer-tainties in statistical luminance and EQE data are significantly reduced from 230% and 140% to 38% and 42%, respectively.

Non-genuine medical products, including diagnostic devices, have become a lucrative business for fraudsters, causing significant damage to revenues and reputation of companies, as well as posing a significant risk to the health of people and societies. Along a “digital twin” representing centrifugal microfluidic flow control on exemplary “Lab-on-a-Disc” (LoaD) systems, a novel, two-pronged strategy to safeguard miniaturized point-of-care devices by means of secret features and manufacturing challenges is outlined; such “hardware encryption” is flexibly programmed for each chip during production, and deciphered from a secure, local or online database at the time of use. This way, unlicensed copying may be efficiently deterred by an unfavourable economy-of-scale, even in absence of legal prosecution.

Smokeless tobacco (ST) products vary significantly in their oral carcinogenicity. Much is known about the differences in chemical, but not bacterial, constituents of these products. In this study, we explore the composition and function of the bacteriome in ST products from 4 countries using q-PCR and 16S rRNA-based next generation sequencing. The bacterial load (16S rRNA copies/gram) was lowest in Swedish snus (3.4E+6) and highest in Yemeni shammah (6.6E+11). A total of 491 species-level taxa, many of which are potentially novel, belonging to 178 genera and 11 phyla were identified. Species richness and diversity were highest for Swedish snus and lowest for Yemeni shammah. Bacillus, Paenibacillus, and Oceanobacillus spp. were the most abundant in American snuff; species of Pseudomonas, Massilia, Propionibacterium, Puniceispirillum and Gloeothece predominated in Swedish snus. In Sudanese toombak, Facklamia, Desemzia, Atopostipes and Lysinibacillus spp. accounted for the majority of the bacteriome. Yemeni shammah exclusively contained Bacillus spp. PICRUSt functional prediction showed that genes encoding cadmium/zinc and nickel transport systems were enriched in the presumptively “high carcinogenicity” products. The bacteriome of ST products thus differed qualitatively, quantitatively and functionally. The relevance of these differences, particularly with respect to nickel and cadmium, to oral carcinogenesis warrants further investigation.

Currently Single Board Computers (SBCs) are sufficiently powerful to run Real-Time Operating Systems (RTOSs) and applications with real-time attributes and requirements. SBCs serve as a foundation in Industrial Internet of Things (IIoT). The NXP Semiconductors produces a series of SBCs based on ARM-processors for a variety of industrial applications. The continuous increase in real-time data generated by IoT devices adds further research issues about the efficiency of such systems and applications. The purpose of this research was to investigate the timing performance of an NXP TWR-K70F120M device with μClinux OS on running concurrently tasks with real-time features and constraints. A custom-built multithreaded application with specific compute-intensive sorting and matrix operations was developed and applied to obtain measurements in specific timing metrics, including task’s execution time, threads waiting time, and response time, under different threads variations. The performance of this device was additionally benchmarked and validated against favorite platforms, a Raspberry Pi4 and BeagleBone AI SBCs. The experimental results showed that this device stands well both in terms of timing and efficiency metrics. Execution times were quite lower than the others, by approximately 56% in the case of two threads, and by 29% in the case of thirty-two threads configurations.

We presented unusual case of double left ventricular false aneurysm complicating late presentation AMI successfully treated with the combination of urgent surgical drainage of tamponade, staged PCI of non-culprit lesion, preventive implantation of ICD-DR, guideline directed heart failure medical therapy and delayed but effective reconstructive operation.

Melasma is a challenging skin condition which involves both structural and functional skin alterations. Despite the availability of various treatment options, the management remains complex. This is the first study to investigate topical application of Rosa Damascena stem cell exosomes when used concomitantly with microneedling in women and men with facial melasma. We recruited 20 subjects with Fitzpatrick skin types I-III, exhibiting melasma of varying severity. The modified Melasma Area and Severity Index (mMASI) and Global Aesthetic Improvement Scale (GAIS) were utilized to evaluate treatment response. The treatment protocol involved microneedling followed by exosome application over four or five sessions, at 4-week intervals. Ninety percent of subjects demonstrated a significant improvement in mMASI scores, while only 10% showed no change. GAIS assessment further supports overall improvement, with just 10% categorized as "not changed". Tolerability was favorable, with mild, transient side effects. Our findings suggest promising outcomes with this combined therapy, underscoring its potential as a safe and effective approach for treating melasma, particularly in severe and moderate cases. However, further research with larger sample sizes and control arms is warranted to validate these findings and explore long-term efficacy.

Wheat, a component of the staple diet globally, is a common food allergen in children. The symptoms of wheat allergy (WA) range from skin rash to shortness of breath, significantly impairing quality of life. Following initial clinical suspicion, individuals may undergo wheat allergen-specific skin prick test (SPT), blood test for serum immunoglobulin E (sIgE) levels or oral food challenge. Conventional management of WA lies in wheat avoidance, yet accidental consumption may be inevitable owing to the ubiquity of wheat in various food products. This article aims to provide an overview of the immunologic pathway of WA, followed by its novel diagnostic methods, namely alcohol-soluble SPT extracts, component-resolved diagnosis and basophil activation test (BAT). The mechanisms underlying wheat allergen-specific oral immunotherapy (OIT) as well as a summary of the efficacy, tolerability and safety of related clinical trials will then be discussed.

Scrub typhus (ST) is one of the most neglected tropical diseases, a leading cause of acute undifferentiated febrile illness in areas of the ‘tsutsugamushi triangle’, diagnosed frequently in South Asian countries. The bacteria Orientia tsutsugamushi is the causative agent of the disease, which enters to human body through the bite of trombiculid mite (Chigger) of the genus Leptotrombidium deliense.The diagnosis of the disease becomes challenging as its early symptoms mimic other febrile illnesses like dengue, influenza, and corona viruses. Lack of rapid, reliable, and cost-effective diagnostic methods further complicates the identification process. Northeast India, a mountainous region with a predominantly rural tribal population, has witnessed a resurgence of scrub typhus cases in recent years. Various ecological factors, including rodent population, habitat characteristics, and climatic conditions, influence its prevalence. Entomological investigations have confirmed the abundance of vector mites, highlighting the importance of understanding their distribution and the probability of transmission of scrub typhus in the region. Proper diagnosis, awareness campaigns, and behavioral interventions are essential for controlling scrub typhus outbreaks and reducing its impact on public health in Northeast India. Further research and community-based studies are necessary to accurately assess the disease burden and implement effective prevention strategies.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In this study, the resource blocks (RB) are allocated to user equipment (UE) according to the evolutional algorithms for long term evolution (LTE) systems. Particle Swarm Optimization (PSO) algorithm is one of the evolutionary algorithms, based on the imitation of a flock of birds foraging behavior through learning and grouping the best experience. In previous work, the Simple Particle Swarm Optimization (SPSO) algorithm was proposed for RB allocation to enhance the throughput of Device-to-Device (D2D) communications and improve the system capacity performance. In simulation results, with less population size of M = 10, the SPSO can perform quickly convergence to sub-optimal solution in the 100^th generation and obtained sub-optimum performance with more 2 UEs than the Rand method. Genetic algorithm (GA) is one of the evolutionary algorithms, based on Darwinian models of natural selection and evolution. Therefore, we further proposed a Refined PSO (RPSO) and a novel GA to enhance the throughput of UEs and to improve the system capacity performance. Simulation results show that the proposed GA with 100 populations, in 200 generations can converge to suboptimal solutions. Therefore, with comparing with the SPSO algorithm the proposed GA and RPSO can improve system capacity performance with 1.8 and 0.4 UEs, respectively.

Exploring the dynamic behavior of cellular metabolism requires a standard laboratory method that guarantees rapid sampling and extraction of the cellular content. We propose a versatile sampling technique applicable to cells with different cell wall and cell membrane properties. The technique is based on irreversible electroporation with simultaneous quenching and extraction by using a microfluidic device. By application of electric pulses in the millisecond range, permanent lethal pores are formed in the cell membrane of Escherichia coli and Saccharomyces cerevisiae, facilitating the release of the cellular contents; here demonstrated by the measurement of glucose-6-phosphate and the activity of the enzyme glucose-6-phosphate dehydrogenase. The successful application of this device was demonstrated by pulsed electric field treatment in a flow-through configuration of the microfluidic chip in combination with sampling, inactivation, and extraction of the intracellular content in a few seconds. Minimum electric field strengths of 10 kV/cm for E. coli and 7.5 kV/cm for yeast S. cerevisiae were required for successful cell lysis. The results are discussed in the context of applications in industrial biotechnology, where metabolomics analyses are important.

Saliva, as a diagnostic medium, offers a promising alternative to blood by virtue of its non-invasive collection, which enhances patient compliance, especially in paediatric and geriatric populations. In this study, we assessed the utility of saliva as a non-invasive medium for measuring V. cholerae-specific serum antibodies in naturally infected individuals. We tested paired serum and saliva samples obtained from a total of 63 cholera patients enrolled in a cohort study. Vibriocidal antibodies assay (IgM/IgG) as markers for accurate determination was used to determine cholera specific antibody levels. Using receiver operating characteristics (ROC) curve, we found that the best cut-off that maximizes (sensitivity + specificity) is 10 titers. At this saliva titer, the sensitivity is 76.9% (95%CI: 60.9%, 87.7%) and specificity is 80.0% (95%CI: 56.6%, 92.5%). Using Spearman’s correlation coefficient, we also found evidence of a positive correlation between Vibrio Cholerae saliva and serum antibodies (rho=0.66, p&lt;0.001). In conclusion, saliva-based diagnostic cholera tests has high diagnostic accuracy, and would be advantageous, cheaper, and quicker for early diagnosis of severe cholera outcomes.

Endometriosis is a disease that affects women of reproductive age and has a significant impact on their well-being. The main symptoms are dysmenorrhea, chronic pelvic pain and infertility. The diagnostic process in many cases is very long and can take up to 8-12 years. Laparoscopy, which is an invasive method, is still necessary to confirm final identification. Therefore, the development of diagnostic markers seems to be crucial for the diagnosis and proper treatment of women affected by endometriosis as soon as possible. Still the most frequently studied and used marker is Cancer Antigen 125 (CA-125). Other glycoproteins, growth factors and immune markers seem to play an important role. However, the search for the ideal endometriosis marker is still ongoing. Developing researches on endometriosis pathogenesis help to identify potential biomarkers or sets of biomarkers in order to improve and speed up the diagnostic process in a non-invasive way.

There is rapidly emerging evidence from pre-clinical studies, patient samples and patient subpopulations that certain chemotherapeutics inadvertently produce prometastatic effects. Prior to this, we showed that doxorubicin and daunorubicin, stiffen cells before causing cell death, predisposing the cells to clogging and extravasation, the latter being a step in metastasis. Here, we investigate which other anti-cancer drugs might have similar prometastatic effects by altering the biophysical properties of cells. We treat myelogenous (K562) leukemic cancer cells with the drugs nocodazole and hydroxyurea, and then measure their mechanical properties using the microfluidic microcirculation mimetic (MMM) device, which mimics aspects of blood circulation and enables the measurement of cell mechanical properties via transit times through the device. We also quantify the morphological properties of cells to explore biophysical mechanisms underlying the MMM results. Results from MMM measurements show that nocodazole- and hydroxyurea-treated K562 cells exhibit significantly altered transit times. Nocodazole caused significant (p &lt; 0.01) increase in transit times, implying a stiffening of cells. This work shows the feasibility of using the MMM to explore possible biophysical mechanisms that might contribute to chemotherapy-induced metastasis. Our work also suggests cell mechanics as a therapeutic target for much needed antimetastatic strategies in general.

Gas embolism is a medical condition leading to the blockage of blood flow in the microvasculature by gas bubbles. While reported as rare, gas embolism often has devastating, fatal physiological consequences. Despite this acute importance, the genesis and evolution of air bubbles in blood vessels under different physiological conditions, such as blood viscosity and blood flow rate, is still understudied, largely because of difficult experimentation and in situ visualization. The objective of this work was to study the gas embolism phenomenon in vitro, using a microfluidic system that mimicked the architecture of microvasculature. The microfluidic systems comprised linear channels with two different air inlet types, namely, T- and Y-junctions with three different widths (20 µm, 40 µm, and 60 µm), and a 30 µm width honeycombed network with three bifurcation angles (30°, 60°, and 90°). Three synthetic liquids equivalent to 0%, 20%, and 46% hematocrit that mimicked the physiological blood viscosity and hematocrit concentrations were used. Our results show that: (i) 20 µm and 40 µm width channels had an elevated risk of gas embolism due to wide fluctuations in the total slug sizes; (ii) the resistance to the flow of air bubbles increased with the increase in the equivalent concentration of hematocrit; (iii) gas bubbles causing blockages and dampening of the flow velocity were frequently observed in 20 µm channels, and lastly (iv) increased risk of gas embolism was observed in the honeycomb architecture with 60° and 30° bifurcations. This work suggests that in vitro experimentation using microfluidic devices with microvascular tissue-like structures opens the possibility of studying this medical condition with high reproducibility and impacts the fact-based medical guidelines for preventing or mitigating iatrogenic occurrences.

Morphological dissimilarity and its evolution over time are one of the most unexpected variations found when comparing cell cultures in 2D and 3D. Monolayer cells appear to flatten in the lower part of the plate, adhering to and spreading in the horizontal plane while not extending vertically. Consequently, cells developed in two dimensions have a forced apex-basal polarity. Co-cultivation and crosstalking between multiple cell types, which control development and formation in the in vivo counterpart, are possible in 3D cultures. With or without a scaffold matrix, 3D model culture may exhibit more in vivo-like morphology and physiology. 3D cultures mimic relevant physiological cellular processes, transforming them into one-of-a-kind drug screening platforms. The structures and dynamics of regulatory networks, which are increasingly studied with live-imaging microscopy, must be considered to help and guarantee the functional maintenance of a 3D structure. However, commercially available technologies that can be used for current laboratory needs are minimal, despite the need to make it easier to acquire cellular kinetics with high spatial and temporal resolution, in order to improve visual efficiency and, as a result, experimentation performance. The CELLviewer is a newly developed multi-technology instrument that integrates and synchronizes the work of various scientific disciplines. The aim of this study is to test the device using two different models: a single Jurkat cell and an MCF-7 spheroid. The two models are loaded into the microfluidic cartridge for each experiment after they have been grown and captured in time-lapse for a total of 4 hours. The samples used are tracked under the operation of the optics after adaptive autofocus, while slipping inside the cartridge chamber, and the 3D rotation was successfully obtained experimentally. The MitoGreen dye, a fluorescence marker selectively permeable to live cells, was then used to determine cell viability. To measure the model diameter, construct fluorescence intensity graphs along a straight line passing through the cell, and visualize the spatial fluorescence intensity distribution in 3D, ImageJ software was used.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

Optofluidics, a research discipline combining optics with microfluidics, currently aspires to revolutionize the analysis of biological and chemical samples e.g. for medicine, pharmacology, or molecular biology. In order to detect low concentrations of analytes in water, we developed an optofluidic device containing a nanostructured substrate for surface enhanced Raman spectroscopy (SERS). The geometry of the gold surface allows localized plasmon oscillations to give rise to the SERS effect, in which the Raman spectral lines are intensified by the interaction of the plasmonic field with the electrons in the molecular bonds. The SERS substrate was enclosed in a microfluidic system, which allowed transport and precise mixing of the analyzed fluids, while preventing contamination or abrasion of the highly sensitive substrate. To illustrate its practical use, we employed the device for quantitative detection of persistent environmental pollutant 1,2,3-trichloropropane in water in submillimolar concentrations. The developed sensor allows fast and simple quantification of halogenated compounds and it will contribute towards the environmental monitoring and enzymology experiments with engineered haloalkane dehalogenase enzymes.

As cardiovascular diseases continue to be a leading cause of mortality, recent-ly, wearable devices for monitoring cardiac activity have gained much interest among medical community. This paper introduces an innovative ECG monitoring system based on a single – lead ECG machine enhanced with machine learning methods. The system only processes and analyses the ECG data, but also predict potential heart disease at an early stage. The wearable device was built on the ADS1298 and a microcontroller STM32L151xD. A server module based on REST API architecture style was designed to fa-cilitate interaction with web-based segment of the system. The module is responsible for receiving data in real time from microcontroller and their deliver to web – based segment. Algorithms for analyzing ECG signals have been developed, including band filter artifact removal, K-means clustering for signal segmentation, and PQRST analysis. Machine leaning methods as Isolation Forest have been employed for ECG anomaly detection. Moreover, a comparative analysis with various machine learning methods, including lo-gistic regression, random forest, SVM, XGBoost, decision forest and, CNNs was conducted to predict cardiovascular diseases. Convoluted Neural Networks (CNN) showed an accu-racy of 0.926, proving high effectiveness in ECG data process.

DKA represents an acute, severe complication of relative insulin deficiency and a common presentation of Type 1 Diabetes Mellitus (T1DM) primarily and, occasionally, T2DM in children and adolescents. It is characterized by the biochemical triad of hyperglycaemia, ketonaemia and/or ketonuria, and acidaemia. Clinical symptoms include dehydration, tachypnoea, gastrointestinal symptoms, and reduced level of consciousness, precipitated by a variably long period of polyuria, polydipsia and weight loss. The present review aims to summarize potential pitfalls in the diagnosis and management of DKA. A literature review was conducted using the Pubmed/Medline databases including articles published from 2000 onwards. Diagnostic challenges include differentiating between T1DM and T2DM, DKA and hyperosmolar hyperglycaemic state (HHS), or between DKA and alternative diagnoses presenting with overlapping symptoms, such as pneumonia, asthma exacerbation, urinary tract infection, gastroenteritis, acute abdomen and central nervous system infection. The mainstays of DKA management include careful fluid resuscitation, timely intravenous insulin administration and restoration of shifting electrolyte disorders and underlying precipitating factors. However, evidence suggests that optimal treatment remains a therapeutic challenge. Accurate and rapid diagnosis, prompt intervention and meticulous monitoring are of major importance to break the vicious cycle of life-threatening events and prevent severe complications during this potentially fatal medical emergency.

Genetic engineering and directed evolution are effective methods to address the low yield and poor industrialization level of microbial target products. The current research focus is on how to efficiently and rapidly screen beneficial mutants from constructed large-scale mutation libraries. Traditional screening methods such as plate screening and well plate screening are severely limited in their development and application due to their low efficiency and high costs. In the past decade, microfluidic technology has become an important high-throughput screening technology due to its fast speed, low cost, high automation, and high screening throughput, and it has developed rapidly. Droplet-based microfluidic high-throughput screening has been widely used in various fields such as strain/enzyme activity screening, pathogen detection, single-cell analysis, drug discovery, and chemical synthesis, and has been widely applied in industries such as materials, food, chemicals, textiles, and biomedicine. In particular, in the field of enzyme research, droplet-based microfluidic high-throughput screening has shown excellent performance in discovering enzymes with new functions, improved catalytic efficiency or stability, acid-base tolerance, etc. Currently, droplet-based microfluidic high-throughput screening technology has achieved high-throughput screening of enzymes such as glycosidase, lipase, peroxidase, protease, amylase, oxidase, and transaminase, as well as high-throughput detection of products such as riboflavin, coumarin, 3-dehydroquinate, lactic acid, and ethanol. This article reviews the application of droplet-based microfluidics in high-throughput screening, with a focus on high-throughput screening strategies based on UV, visible, and fluorescence spectroscopy, including labeled optical signal detection screening, as well as label-free electrochemical detection, mass spectrometry, Raman spectroscopy, nuclear magnetic resonance, etc. Furthermore, the research progress and development trends of droplet-based microfluidic technology in enzyme modification and strain screening are also introduced.

Plant cells are omnipotent and breeding of new varieties can be achieved by protoplast fusion. Such fusions can be achieved by treatment with poly(ethylene glycol) or by applying an electric field. Microfluidic devices allow for controlled conditions and targeted manipulation of small batches of cells down to single cell analysis. To provide controlled conditions for protoplast fusions and achieve high reproducibility, we developed and characterized a microfluidic device to reliably trap few of Arabidopsis thaliana protoplasts and induced a cell fusion by controlled addition of poly(ethylene glycol) (PEG, with a molecular weight of 6000). Experiments were conducted to determine the survival rate of isolated protoplasts in our microfluidic system. Afterwards, PEG induced fusion was studied. Our results indicate that the following fusion parameters had significant impact on the fusion efficiency and duration: PEG concentration, osmolarity of solution, and flow velocity. PEG concentration below 10% led to only partial fusion. Osmolarity of the PEG fusion solution was found to strongly impact the fusion process; complete fusion of two source cells sufficiently took part in slightly hyper osmotic solutions, whereas iso-osmotic solutions led to only partial fusion at 20% PEG concentration. We observed accelerated fusion for higher fluid velocities. Up to this study, it was common sense that fusion is one directional, i.e. once two cells were fused into one cell they stay fused. Here, we present for the first time reversible fusion of protoplasts. Our microfluidic device paves the way to a deeper understanding on the kinetics and processes of cell fusion.

Separation and interpretation of rebellious Circulating Tumor Cells (CTCs) originating from the primary tumor or cancer tissue plays a significant role in diagnostics, cancer progression analyses, suitable medicine exploration, and treatment proficiency examination. Cancer metastasis occurs when CTCs spread throughout the body and invade healthy tissues, leading to new tumors in that area. Although a dramatic rate of deaths begins from spreading CTCs around the body, valuable measures have been made to control their development. However, the first step is separating these harmful cells from the bloodstream and investigating their features. Having examined the characteristics of CTCs as cancer’s main strength, researchers can introduce complementary treatments that can affect cancerous cells without damaging the healthy cells. Therefore, according to their unique characteristics, numerous techniques have been established for continuous and fast separation and sorting of CTCs. Nevertheless, few separators enjoy the efficient performance and appropriate accuracy and can be produced in mass numbers due to the available fabrication equipment. Microfabrication advancements enable separators to combine the advantages of active and passive methods in a small-scale platform for probing individual cells and separation purposes. Reduction in reagents, sample volume, analysis time, and less harmfulness to patients are some of the motivations that encourage researchers to employ microfluidic instruments for CTCs separation from other blood cells over the last two decades. However, microfabrication limitations mean effective separators, and the diagnostic option they provide, are not readily available. Addressing these limitations requires optimizing the design and fabrication of separators such that they are reduced in their size and fabrication cost, while also maintaining high-throughput separating capability. The emergence of the Lab-On-a-Chip (LOC) and then Lab-On-a-CD (LOCD) technologies, having more inherent benefits than conventional microfluidic devices, has created new opportunities and become increasingly widespread in recent years. Evidence suggests that employing single methodologies or integrating approaches without sufficient understanding of potential outcomes is unlikely to result in successful diagnostic results. This paper contributes an extensive review of several separation systems, including fundamental theories and experimental details, and describes detailed operating principles and device performance.

Advances in gastric cancer screening and endoscopic technology have made it possible to detect and treat gastric cancer at an early stage. As a result, about 40% of all gastric cancers have now been resected by endoscopic treatment in Japan. In endoscopic diagnosis, magnifying endoscopic observation using band-limited light such as narrow band imaging (NBI) has significantly improved the accuracy of gastric cancer diagnosis. At the same time, in endoscopic treatment, endoscopic submucosal dissection (ESD) has contributed to increase explosively the number of gastric cancers which could be resected endoscopically. In recent years, the construction of algorism for endoscopic diagnosis and treatment with a view to personalized medicine has been explored, and endoscopic use for gastric cancer managements is expected to develop further in the future. Keywords (5 words):

Renal clear cell carcinoma (ccRCC) comprises over 75% of all renal tumors and arises in the epithelial cells of the proximal convoluted tubule. Molecularly ccRCC is characterized by copy number alterations (CNAs) such as the loss of chromosome 3p and VHL inactivation. Additional driver mutations (SETD2, PBRM1, BAP1, and others) promote genomic instability and tumor cell metastasis through the dysregulation of various metabolic and immune-response pathways. Many researchers identified mutation, gene expression, and proteomic signatures for early diagnosis and prognostics for ccRCC. Despite a tremendous influx of data regarding DNA alterations, gene expression, and protein expression, the incorporation of these analyses for diagnosis and prognosis of RCC into the clinical application has not been implemented yet. In this review, we focused on the molecular changes associated with ccRCC development, along with gene expression and protein signatures, to emphasize the utilization of these molecular profiles in clinical practice. These findings, in the context of machine learning and precision medicine, may help to overcome some of the barriers encountered for implementing molecular profiles of tumors into the diagnosis and treatment of ccRCC.

The article analyzes existing materials and structures with quadratic-nonlinear optical properties that can be used to generate a difference frequency in the terahertz and sub-terahertz frequency ranges. The principle of constructing a nonlinear optical-radio converter, based on an optical focon (a focusing cone), is proposed. Based on the assumption that this focon can be implemented from the metal-organic framework (MOF), we propose a technique for modeling its parameters. The mathematical model of the process of propagation and nonlinear interaction of waves inside the focon is based on a simplification of the nonlinear wave equation. Within the framework of the developed model, the following parameters are approximately determined: the 3D gradient of the linear refractive index and the function determining the geometric profile of the focon, which provide a few-mode-based generation of the difference frequency.

This study aimed to evaluate the diagnostic roles of various immunohistochemical markers in urothelial carcinoma in situ (uCIS) through a meta-analysis and review of diagnostic test accuracy. Immunohistochemical markers CK20, CD44, AMACR, and p53 were evaluated in the present study. We analyzed the expression rates of immunohistochemical markers and compared their diagnostic accuracies. The estimated expression rates were 0.803 (95% confidence interval [CI]: 0.726–0.862), 0.142 (95% CI: 0.033–0.449), 0.824 (95% CI: 0.720–0.895), and 0.600 (95% CI: 0.510–0.683) for CK20, CD44, AMACR, and p53, respectively. In the comparison between uCIS and reactive/normal urothelium, the expression of CK20, AMACR, and p53 in uCIS was significantly higher than in reactive/normal urothelium. CD44 showed significantly lower expression in uCIS than in the reactive/normal urothelium. Among the markers, AMACR had the highest sensitivity, specificity, and diagnostic odds ratio. The AUC on SROC was the highest for CK20. In conclusion, immunohistochemical markers, such as CK20, CD44, AMACR, and p53, can be useful in differentiating uCIS from reactive/normal urothelium.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

Digital Microfluidic Biochips (DMFBs), used in various kinds of fields like DNA analysis, clinical diagnosis, and PCR testing, have made biochemical experiments more compact, efficient, and user-friendly than previous ways. However, their reliability is often compromised by their inability to adapt to all kinds of errors. All errors in biochips can be categorized into two types: known errors and unknown errors. Known errors are detectable before the start of the routing process through sensors or cameras. Unknown errors, in contrast, become apparent only during the routing process and remain undetected by sensors or cameras, which is the biggest issue to unexpectedly stop the routing process and diminishes the reliability of biochips. This paper introduces a deep reinforcement learning-based routing algorithm designed to manage not only known errors but also unknown errors. Our experiments demonstrate that our algorithm outperforms previous ones in terms of the success rate of the routing in the scenario including both known errors and unknown errors. Additionally, our algorithm contributes to detecting unknown errors during the routing process and identifying the most efficient routing path with high probability.

Leukodystrophies, also known as demyelinating diseases, mainly affect the CNS. Clinical presentation of different types of leukodystrophies can be nonspecific and thus, imaging techniques like MRI can be used for a more definitive diagnosis. These diseases are characterized as cerebral lesions with characteristic demyelinating patterns, which can be used as differentiating tools. In this review, we talk about these MRI imaging findings for each leukodystrophy, associated genetics, blood work that can help differentiate, emerging diagnostics, and follow up imaging strategy. The leukodystrophies discussed in this paper include X-linked adrenoleukodystrophy, Metachromatic leukodystrophy, Krabbe’s disease, Pelizaeus-Merzbacher disease, Alexander’s disease, Canavan disease, and Aicardi-Goutières Syndrome.

The proliferation of radio frequency devices in today's society, especially in smart homes, Internet of Things devices, and smartphones, underscores the urgent need for robust identification methods to strengthen cybersecurity. This paper delves into the field of radio frequency fingerprinting to propose a Bluetooth device identification method based on the application of the Jensen-Shannon divergence to the statistical distribution of noise in Bluetooth signals. A detailed case study is performed to investigate the Bluetooth radio frequency noise recorded at 5 Gsps from different devices is investigated to define a statistical radio frequency fingerprint for each Bluetooth device. A noise model is used to extract a unique, universal, persistent, recoverable, and robust statistical radio frequency fingerprint that identifies each Bluetooth device. Then, using the Jensen-Shannon divergence, different noise signals provided by each Bluetooth device are compared with the statistical radio frequency fingerprint of all devices and a membership resolution is declared. The study shows that the proposed method can discriminate between devices of the same brand and model, achieving an identification effectiveness of 99.5 \%. By leveraging the statistical radio frequency fingerprint of Bluetooth devices, this research not only contributes to the advancement of the field of implicit device authentication systems based on wireless communication but also provides valuable insights into the practical implementation of radio frequency identification techniques that could be useful in forensic processes.

The application of electrode-based microfluidic devices in biological entity often imposes a problem due to joule heating. The strong applied potentials or micro channels having narrow cross sections generate undesirable temperature inside the microfluidic channels leading to strong thermal distribution inside the micro channel. When intrinsic distribution of temperature, if not fix with threshold value, causes device damage or cell loss. In this work, we investigate the effects of temperature generated due to joules heating effects and we attempt to address the design constraints for minimizing the joule heating effects in the microfluidic device for developing effective microfluidic device. The device reliability was analyzed under different parametric constraints for various types of substrate materials (PDMS, PMMA, Polyimide and glass). We also attempt to investigate the effects of cell reliability due to strong temperature gradients generated through different applied potentials on different cell types. Furthermore, the response of the device performance due to different electrode configuration and different conductivity of the medium was also studied. Our investigation will eventually provide guidelines for microfluidic researchers to fabricate efficient electrode based microfluidic device which will ultimately help to choose a critical channel dimensions, threshold potentials, and conductivity of solutions in order to avoid device damage and cell loss.

Heavy metal contaminants have serious consequences for the environment and human health. Consequently, effective methods for detecting their presence, particularly in water and food, are urgently required. Accordingly, the present study proposes a sensor for the detection of mercury Hg(II) and lead Pb(II) ions using graphene oxide (GO) as a quenching agent and aptamer solu-tion as a reagent. In the proposed device, the aptamer sequences are labeled by FAM and HEX fluorescent dyes, respectively, and are mixed with 500 ppm GO solution in a microfluidic device. The presence of Hg(II) and Pb(II) ions is then detected by measuring the change in the fluores-cence intensity of the GO/aptamer suspension as the aptamer molecules undergo fluorescence resonance energy transfer (FRET). The experimental results show that the aptamer sensors have a linear range of 10~250 nM (i.e., 2.0~50 ppb) for Hg(II) ions and 10~100 nM (i.e., 2.1~20.7 ppb) for Pb(II) ions. Furthermore, the limit of detection is around 2 ppb for both metals, which is signifi-cantly lower than the maximum limits of 6 ppb and 10 ppb prescribed by the World Health Or-ganization (WHO) for Hg(II) and Pb(II) in drinking water, respectively.

Abstract: Recent years demonstrate the increased attention to radon from two scientific directions. After neglecting radon as earthquake precursors in 1990-th it becomes again the subject of earthquake-forecast papers discussions due to growing networks of the radon monitoring in different countries, especially, the technologies of real-time radon measurements where the gamma-spectrometers become the leader of interest as the sources of 222Rn identification. The second fast developing direction is including the radon in the Lithosphere-Atmosphere-Ionosphere Coupling (LAIC) models as a source of the boundary layer ionization. And here we encounter with second direction which is not connected with the earthquake forecast problems. It is the role of air ionization by radon as a source of the Global Electric Circuit (GEC) modification. In this publication we try to unite all these problems to present more complex view on radon as important element of our environment.

Neutropenia refers to a decrease in the absolute neutrophil count according to age and race norms and poses a common concern in pediatric practice. Neutrophils serve as host defenders and act crucially in acute inflammation procedures. In this narrative review we systematically present causes of neutropenia in childhood mainly adopting the pathophysiological classification of Frater, thereby studying: (1) neutropenia with reduced bone marrow reserve, (2) secondary neutropenia with reduced bone marrow reserve, and (3) neutropenia with normal bone marrow reserve. Different conditions in each category are thoroughly discussed and practically approached from the clinician point of view. Secondary mild to moderate neutropenia is usually benign due to childhood viral infections and is expected to resolve in 2- 4 weeks. Bacterial and fungal agents are also associated with transient neutropenia although fever with severe neutropenia constitutes a medical emergency. Drug-induced and immune neutropenias should be suspected following a careful history and a detailed clinical examination. Cytotoxic chemotherapies treating malignancies are responsible for severe neutropenia and neutropenic shock. Rare genetic neutropenias usually manifest with major infections early in life. Our review taxonomies clinical findings and associates them to specific neutropenia disorders. We consequently propose a practical diagnostic algorithm for managing neutropenic children.

This study aimed to evaluate the diagnostic and prognostic roles of GATA3 immunohistochemistry in urothelial carcinoma (UC) through a meta-analysis. We investigated GATA3 immunohistochemical expression rates and performed a subgroup analysis based on tumor site, study location, and histological subtypes. The overall survival rates of patients with GATA3-positive and negative UC were compared. The estimated GATA3 expression rate was 0.748 (95% confidence interval [CI]: 0.704–0.787). GATA3 expression rates in the urinary bladder and urinary tract were 0.775 (95% CI: 0.727–0.818) and 0.614 (95% CI: 0.426–0.774), respectively. The GATA expression rates of noninvasive and invasive UCs were 0.965 (95% CI: 0.938–0.980) and 0.644 (95% CI: 0.581–0.702), respectively. In invasive UCs, there was a significant difference in GATA3 expression between non-muscular invasion and muscular invasion subgroups (0.937, 95% CI: 0.883–0.967 vs. 0.753, 95% CI: 0.645–0.836). GATA3 expression was the highest in the microcytic subtype among the histologic subtypes (0.952, 95% CI: 0.724–0.993). There was a significant correlation between GATA3 expression and better prognosis (hazard ratio: 0.402, 95% CI: 0.311–0.521). Taken together, GATA3 expression significantly correlated with low-stage and better prognosis in UC. GATA3 expression is highly variable across histological subtypes and it is careful interpreting GATA3 expression.

Feline infectious peritonitis (FIP), caused by the feline coronavirus (FCoV), is a devastating dis-ease in cats. Based on its antigenicity, FCoV can be divided into two serotypes: FCoV-I and FCoV-II. Furthermore, according to its pathogenicity, FCoV can be divided into feline enteric coronavirus (FECV) and feline infectious peritonitis virus (FIPV). There are numerous factors that affect the pathogenesis of FIP, among which host immunity and viral genetics can play an es-sential role in the development of FIP. Owing to the lack of specific symptoms, existing individual diagnostic methods can only support the suspicion of FIP, and multiple diagnostic methods and test data need to be combined to make a diagnosis. Although there are still no effective FIPV vaccines or commercial drugs available in the market, various studies have shown that some compounds can be used for treatment. Therefore, FIP is no longer incurable in cats

Smartwatches provide technology-based assessments in Parkinson’s disease (PD). We present results for sensor validation and disease classification via Machine Learning (ML). A comparison setup was designed with two different series of Apple smartwatches, one Nanometrics seismometer and a high-precision shaker to measure tremor-like amplitudes and frequencies. Clinical smartwatch measurements were acquired from a prospective study including 450 participants with PD, differential diagnoses (DD) and healthy participants. All participants wore two smartwatches and within a 15-min examination. Symptoms and medical history were captured on the paired smartphone. A broad range of different ML classifiers were cross-validated. Amplitude and frequency differences between smartwatches and the seismometer were under the level of clinical significance. The most advanced task of distinguishing PD vs DD was evaluated with 74,1% balanced accuracy, 86,5% precision and 90,5% recall by Multilayer Perceptrons. Deep Learning architectures significantly underperformed in all classification tasks. Smartwatches are capable of capturing subtle-tremor signs with low noise. This study provided the largest PD sample size of two-hand smartwatch measurements and our preliminary ML-evaluation shows that such a system provides powerful means for diagnosis classification and new digital biomarkers but it remains challenging for distinguishing similar disorders.

Non-targeted effects (NTE) such as bystander effects or genomic instability have been known for many years but their significance for radiotherapy or medical diagnostic radiology are far from clear. Central to the issue are reported differences in response of normal and tumour tissues to signals from directly irradiated cells. This review will discuss possible mechanisms and implications of these different responses and will then discuss possible new therapeutic avenues suggested by the analysis. Finally, the importance of NTE for diagnostic radiology and nuclear medicine which stems from the dominance of NTE in the low dose region of the dose response curve will be presented. Areas such as second cancer induction and microenvironment plasticity will be discussed.