Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

This paper presents a study of the 2D roughness profiles on a flat surface generated on a steel work piece, by ball nose end milling, with linear equidistant tool paths (pick-intervals). The milled surface exploration with a surface roughness tester (on pick and feed directions) produces usually 2D roughness profiles having periodical evolutions. These evolutions can be seen as time-dependent signals, describable as a sum of sinusoidal components (the wavelength of each component being regarded as a period). In order to detect a well approximated description of these components, two appropriate signal processing techniques are used in this work: first technique provides a direct mathematical (analytical) description and is based on computer aided curve (signal) fitting (more accurate), the second technique (providing an indirect and incomplete description) is based on the spectrum generated by fast Fourier transform (less accurate). This study can be seen as a way for a better understanding the interaction between the tool and the work piece or to achieve a mathematical description of the machined surface microgeometry in terms of roughness (e. g. its description being a collection of closely spaced 2D roughness profiles).

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

With the advancement of the economy and society, policymakers acknowledge the significance of improving rural households' well-being as a crucial factor in promoting sustainable economic and social development. Based on the matching data of China Household Finance Survey and Digital Rural County Index, this study empirically examines the effect and mechanisms of digital village construction on subjective well-being of rural households. The results revealed that digital village construction has a significant improvement in their subjective well-being. The impact of digital village construction is particularly significant in rural areas located in the western regions of China, as well as among households possessing higher levels of human capital. The process through which digital village construction enhances the subjective well-being of rural households involves the augmentation of household income, the promotion of non-farm employment opportunities, and the enhancement of rural governance. This study provides robust micro-empirical evidence highlighting the positive welfare effects of digital rural construction. This study provides insights into the digital village construction within the happiness economy framework, offering a new perspective. The imperative to strengthen rural digital infrastructure and improve farmers' proficiency in modern information skills is a strategic policy aimed at enhancing well-being of rural households.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

The construction industry is a resource and energy intensive industry and thus, has been criti-cized due to rising environmental concerns. As a result of that it has gained heightened interest in the concept of Circular Economy (CE) over the last decade to its ability to promote the slowing, reducing, and closing production and consumption cycles of materials and products used in the construction practices. Digital technologies hold potential to enhance the construction industry's ability to integrate the concept of CE in its practices. However, a clear understanding of digital technology (DT) related barriers that hinder practical implementation of CE, appears to be lacking within the sector. In light of this, this study aims to identify the barriers to adopting DTs to im-plement CE practices in the construction industry. To achieve this aim, a systematic literature review was conducted by reviewing twenty-three (23) relevant papers published until January 2024 in Scopus database. The VOS viewer software was used to perform a co-occurrence analysis of keywords to identify new and popular study areas in the field and content analysis was used to analyse the major barriers to adapt DTs to implement CE in the construction industry. The study identified thirty-four (34) barriers to use DTs to implement CE and these were categorized into nine areas such as: infrastructure, organizational, regulatory, standardization, investment, nature of the construction industry, technological, stakeholder and data related barriers. These findings will be beneficial for construction practitioners and policy makers to adopt DTs to integrate CE practices in the construction industry.

The collapsible loess will rapidly soften and lose its bearing capacity when soaked in water. Under a mild condition (20°C), the biomimetic inorganic agent, Diammonium phosphate (DAP), reacts with calcite in the collapsible loess, producing a stronger bonding material, hydroxyapatite (HAP), to modify and stabilize the soil. Uniaxial compression, permeability tests and morphological analysis using XRD and SEM/EDX microscopy were carried out to assess the effectiveness of DAP stabilization on the collapsible loess. The results indicated that HAP improved the inter-particle bonding within loess, filled the pores within particles, reduced the permeability, and consequently mitigated collapsibility of loess. The compressive strength of DAP-treated loess increased as DAP concentration increased. Following 28-days curing, the compressive strength of the loess treated with a 3.0 mol/L DAP solution was six times greater than that of the untreated group. DAP's reinforcement effect on loess was superior to that of cement. The compressive strength of DAP-treated loess was about double that of cement-treated loess and the permeability coefficient was reduced by more than 50% at equivalent solid content. Furthermore, DAP generated 68% fewer carbon emissions compared to Portland cement. Considering eco-friendly and sustainable development, DAP offers a more competitive alternative for modification and stabilization of loess.

This paper will discuss Data, Information, Knowledge, and Wisdom, which is commonly referred to as DIKW. The DIKW Pyramid Model that is often referenced in both academics and practitioner circles will be discussed and shown to be faulty on several levels, including. a lack of definitional agreement. A new DIKW framework will be proposed that focuses on what the DIKW elements do in the way humans think, not what they are by definition. Information as a replacement for wasted physical resources in goal-oriented tasks will be a central organizing point. The paper will move the DIKW discussion to the computer-based concept of Digital Twins (DTs) and its augmentation of how we can use DIKW to be more effective and efficient. This will especially be the case as we move to Intelligent Digital Twins (IDT) with Artificial Intelligence (AI).

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

The domain of construction engineering and management is evolving rapidly. Optimizing resource positioning is crucial for meeting the challenges of efficiency and productivity. This research presents a novel methodology that incorporates Agent-Based Modeling (ABM), Building Information Modeling (BIM), and Bluetooth Low Energy (BLE) technologies, augmented with a Client Early Warning System (CEWS) and a Decision Support System (DSS). What makes this study unique is that it provides a real-time methodology for resource allocation and project management, tailored to address the complexities of modern construction projects. The application of this integrated technological framework marks a significant leap in construction management, empowering data-driven decision-making and significantly improving project efficiency. Empirically validated through a case study at Helwan University's College of Engineering and substantiated by expert surveys, this research showcases a transformative model for resource management. The findings not only underscore the practical applicability of this approach but also open new horizons for its adoption in global construction practices, offering insights for future research endeavors focused on expanding these methodologies to a wider range of resources.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

The mineralogical indices, e.g., Quartz Index (QI), Carbonate Index (CI), Mafic Index (MI) for ASTER multispectral thermal infrared (TIR) data have been applied to various geological materials. The indices are proved to be robust in extracting geological information at the local scale. Considering the relatively narrow spatial coverage of each ASTER scene compared to LANDSAT, many scenes are needed when mosaicking the images to be mapped at regional scales. We develop a system to search ASTER data for a target area given the vast and expanding ASTER data archive. The data is then conditioned, prioritized, and the indices are calculated before finally mosaicking the imagery. The maps of the indices covering the very wide region of the central Tibetan Plateau are produced with this system. The characteristic features of the indices relating to their geology in the study area are analyzed and discussed. Many interesting lithological and structural information that are not currently well understood in the central Tibetan Plateau, the highest and most extensive plateau in the world, with an average elevation of over 4,500 meters above sea level, for example, distributions of the mafic-ultramafic rocks along the suture zones, the quarzitic and marine sedimentology accreted to the Eurasian continent and sulfate layers related to the Tethys and neo-Tethys geological setting can be retrieved from the processed ASTER images.

Construction 4.0 is witnessing exponential growth in Digital Twin (DT) technology developments and applications, revolutionizing the adoption of Building Information Modelling (BIM) and other emerging technologies used throughout the lifecycle of the built environment. BIM provides technologies, procedures, and data schemas representing building components and systems. At the same time, DT enhances this with real-time data for cyber-physical integration, enabling live asset monitoring and better decision-making. Despite being in the early stages of development, DT applications have rapidly progressed in the AEC sector, resulting in a diverse literature landscape due to the various technologies and parameters involved in fully developing the DT technology. The intricate complexities inherent in digital twin advancements have confused professionals and researchers. This confusion arises from the nuanced distinctions between the two technologies, i.e., BIM and DT, causing a convergence that hinders realizing their potential. To address this confusion and lead to a swift development of DT technology, this study presents a holistic review of the existing research focusing on the critical components responsible for developing DT applications in the construction industry. The study identifies five crucial elements: technologies, maturity levels, data layers, enablers, and functionalities. Additionally, it identifies research gaps and proposes future avenues for streamlined DT developments and applications in the AEC sector. Future researchers and practitioners can target data integrity, integration and transmission, bi-directional interoperability, nontechnical factors, and data security to achieve mature digital twin applications for AEC practices. This study highlights the growing significance of DTs in construction and provides a foundation for further advancements in this field to harness its potential to transform built environment practices.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

The described data set contains features from the machine control of a five-axis milling machine. The features were recorded during thirteen series productions. Each series production includes a changeover process in which the machine was set up for the production of a different product. In addition to the timestamps and the twenty recorded features derived from Numerical Control (NC) control variables, the data set also contains labels for the different production phases. For this purpose, up to 23 phases were assigned, which are based on a generalized milling process. The data set consists of thirteen .csv files, each representing a series production. The data set was recorded in a production company in the contract manufacturing sector for components with real series orders in ongoing industrial production.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

Productivity has been modest in construction due to many reasons, especially project-specific operations and fragmentation. The main aim of this research is to map the challenges towards industrialization in construction through a comparative study of the manufacturing industry. An inductive approach and a qualitative method are followed by applying semi-structured inter-views, and node-based thematic analysis. The key elements of industrialization in mature man-ufacturing companies are benchmarked. The findings indicate a specific order of steps for indus-trialization in construction. Data and information management with achieved systematization have been sources of productivity in manufacturing companies. However, the systematization starts from the offering, construction companies need to define their offering, that is the products, and define their respective data. Only accurate and good quality data on products enables the systematization of order delivery processes, which are the engine for a company’s success or failure. Continuous efficiency improvement is only possible with systematized processes and respective data related to the processes. The originality involves clarifying the industrialization of construction companies via products, respective data, and processes considering industrialized manufacturing companies.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

Facility Management (FM) has increasingly focused on using Building Information Modeling (BIM) in large-scale development projects. To successfully integrate BIM in the FM sector, cooperation among different participants involved in various project stages must be improved. The objective of this digital revolution in FM is to enhance the efficacy of planning, constructing, and managing assets, benefiting all parties involved. However, the utilization of BIM in FM is limited due to factors such as incomplete owner understanding, insufficient data accessibility, and stakeholders' unfamiliarity with BIM procedures and standardization. Although the FM industry acknowledges BIM's significance, achieving successful implementation remains challenging. Facility managers lack a clear understanding of BIM's benefits in expediting operations and cost efficiency and the necessary skills for efficient utilization. To address this constraint, it is essential to develop an Employee’s Information Requirement (EIR) at the outset of a project, serving as a strategic plan and providing a comprehensive vision for all parties involved, particularly large-scale projects. Two essential technologies that facilitate the transition towards building operations are BIM and the Internet of Things (IoT). Incorporating these technologies is crucial to reducing time, expenses, and operational challenges throughout any project. The aim of this research is to create a Digital-Trio workflow, as a new expression, by providing a methodology for using facility management with BIM through the integration of EIR and IoT, maximizes the benefit of stakeholders strategically and operationally. It also explores how the preparation of the EIR by communicating with all parties will definitely improve the design process, sustainability, efficiency, cost, and time for any project, especially megaprojects.

Organisational performance is a major concern for any company wishing to remain competitive in today's market. This is why many companies have begun to integrate digital technologies into their management systems. The aim of this article is to determine the contribution of digitisation to organisational performance management, through observations and analysis of a single case study of a company that has adopted a digital transformation project. It emerged that digital transformation makes a significant contribution to organisational performance management. However, this transformation requires significant support and adaptation of skills and organisational structures.

With the continuous development of digital transformation and upgrading of Chinese construction enterprises, it is becoming increasingly important to measure their digital level, find the problems in the enterprise transformation process, and identify the key factors of enterprise digital capacity enhancement. This paper constructs a construction enterprise digital transformation maturity evaluation model from six first-level indicators and 20 second-level indicators, including digital strategy, digital business application, digital technology capability, data capability, digital organization capability, and change management. Digital maturity is divided into five levels: business management, process operation, intelligent construction, intelligent scene application, and industrial ecological collaboration. A detailed process of digital maturity evaluation based on the method of Analytic Hierarchy Process (AHP)-Decision Testing and Evaluation Laboratory (DEMATEL) is then developed. A questionnaire survey of 25 experts is used to weight the various parameters in the model, which is then demonstrated with an example construction enterprise. The model comprehensively reflects digital levels under the background of the digital economy. Its application will help understand the advantages and disadvantages enterprises face in their digital transformation to enable targeted measures to improve their digital transformation capabilities and efficiency, enhance their core competitiveness of enterprises, and promote the development of digital transformation in the construction industry.

This paper presents the systematic development and performance characterization of a non-proprietary 3D-printable ultra-high-performance fiber-reinforced concrete (UHPFRC) for digital construction. Several fresh and hardened properties of the developed 3D-printable UHPFRC matrix (without fiber) and composite (with 2% volume fraction of steel fibers) were evaluated and compared to that of conventionally mold-cast UHPFRC. Additionally, the effects of testing direction on the compressive and flexural strengths of the printed UHPFRC were investigated. The fresh properties of the UHPFRC developed in this study satisfied the criteria for extrudability, buildability, and shape-retention-ability, which are relevant for ensuring printability. The printed UHPFRC exhibited superior flexural performance to the mold-cast UHPFRC due to alignment of the short fibers in the printing direction. The high compressive and flexural strengths, along with the deflection-hardening behavior, of the developed UHPFRC can enable the production of thin 3D-printed components with significant reduction or complete elimination of conventional steel bars.

Design for Manufacture and Assembly (DfMA) in architectural, engineering, and construction (AEC) industry is attracting the attention of designers, practitioners, and construction project stakeholders. Digital fabrication (Dfab) and design for additive manufacturing (DfAM) practices are found in current needs for further research and development. The DfMA's conceptual function is to maximize the process efficiency of Dfab and AM building projects. This work reviewed 171 relevant research articles over the past few decades. The concept of DfMA and the fundamentals of DfMA in building and construction were explored. In addition, DfMA procedures associated with Dfab and DfAM, as well as its AM assembly process, were discussed. Lastly, the current machine learning research on DfMA in construction was also highlighted. Large research gaps in the DfMA for Dfab and DfAM can be filled to increase operational efficiency and sustainable practices.

Digital infrastructure is the basic guarantee for digital transformation, it is of practical significance to discuss how to effectively use digital infrastructure construction to promote the digital transformation of tourism enterprises. This paper examines the impact of digital infrastructure construction on tourism enterprises based on the "Broadband China" policy as a quasi-natural experiment. A-share tourism listed enterprises from 2010 to 2021 are studied using the double difference method. Findings indicate that digital infrastructure construction positively and significantly influences the digital transformation of tourism enterprises, driven by digital leadership and innovation capabilities. State-owned, small-scale, and high-growth tourism enterprises benefit more from this transformation. The results suggested that the state should develop differentiated digital infrastructure plans based on the specific conditions of different tourism enterprises. Additionally, tourism enterprises should enhance digital leadership and innovation capabilities through strategic changes and digital applications to amplify the impact of digital infrastructure on their transformation.

Digital federated platforms and data cooperatives for secure, trusted and sovereign data exchange will play a central role in the construction industry of the future. With the help of platforms, cooperatives and their novel value creation, the digital transformation and the degree of organization of the construction value chain can be taken to a new level of collaboration. The goal of this research project was to develop an experimental prototype for a federated innovation data platform along with a suitable exemplary use case. The prototype is to serve the construction industry as a demonstrator for further developments and form the basis for an innovation platform. It exemplifies how an overall concept is concretely implemented along one or more use cases that address high-priority industry pain points. This concept will create a blueprint and a framework for further developments, which will then be further established in the market. The research project illuminates the perspective of various governance innovations to increase industry collaboration, productivity and capital project performance and transparency as well as the overall potential of possible platform business models. However, a comprehensive expert survey revealed that there are considerable obstacles to trust-based data exchange between the key stakeholders in the industry value network. The obstacles to cooperation are predominantly not of a technical nature, but of a competitive, predominantly trust-related nature. To overcome these obstacles and create a pre-competitive space of trust, the authors therefore propose the governance structure of a data cooperative model, which is discussed in detail in this paper.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P < 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

This paper explores Ghana's two-decade journey in developing a digital land information system (LIS), exemplified by Ghana Enterprise Land Information System (GELIS) and Enterprise Land Information System (ELIS). Despite advancements by Ghana’s Lands Commission, manual processes persist and coexist with digital ones. Our study uses a qualitative approach to assess the effectiveness of the LIS implemented in Accra. The study found that Accra’s LIS is highly aligned with clear institutional mandates, roles, and responsibilities as well as the availability of laws and policies to support analogue to digital conversion. Furthermore, a robust approach for protecting data, operating system and software underpins the system. Subsequently, the integration of a digital LIS has enhanced service delivery and accountability. Nonetheless, Accra’s LIS is still at the beginning of a comprehensive learning and development curve. To sustain the LIS requires furtherance in the implementation plan, funding, law implementation, ICT strategy, divisional integration, work processes, data quality, and communication strategy. These findings will inform the next steps of improvement for Accra's LIS and guide its nationwide scaling, contributing to discussions on technology acceptance dynamics in predominantly analogue environments.

The purpose of this study is to establish whether digital literacy and insurtech adoption influence insurance inclusion in Uganda. Principally, we sought to determine whether insurtech adoption mediates the nexus between digital literacy and insurance inclusion. This study adopted a cross-sectional and quantitative correlational approach. The study’s sample was 391 individuals who had used digital platforms such as mobile phones and computers to access insurance products and services in Uganda. Data were collected using structured survey questionnaires. Partial Least Squares Structural Equation Modelling (PLSEM) was employed to test the hypothesised relationships. The results demonstrate that both digital literacy and insurtech adoption significantly and positively influence insurance inclusion. We also found digital literacy to be a significant and positive determinant of insurtech adoption. Markedly, it was found that insurtech adoption mediates the association between digital literacy and insurance inclusion in Uganda. However, this study was conducted in a developing country with an underdeveloped insurance market and with low technological advancement. This may affect generalisation of the study findings. This study’s novelty lies in establishing how digital literacy and insurtech adoption interplay to influence insurance inclusion in Uganda. This is the first study to examine the effect of digital literacy and insurtech adoption on insurance inclusion.

Buildability, i.e. the ability of a deposited material bulk to retain its dimmensions under increasing load, is an inherent prerequisite for formwork-free digital construction (DC). Since DC processes are relatively new, no standard methods of characterization are available yet. The paper at hand presents practice-oriented buildabilty criteria by taking various process parameters and construction costs into consideration. In doing so, direct links between laboratory buildability tests and target applications are established. A systematic basis for calculating the time interval (TI) to be followed during laboratory testing is proposed for the full-width printing (FWP) and filament printing (FP) processes. The proposed approach is validated by applying it to a high-strength, printable, fine-grained concrete. Comparative analyses of FWP and FP revealed that to test the buildability of a material for FP processes, higher velocities of the printhead should be established for laboratory tests in comparison to those needed for FWP process, providing for equal construction rates.

The conventional well placement was done manually by using a numerical reservoir simulator, and it required a lengthy trial-and-error process. It required great experience and expertise to manipulate the variables and uncertainties that lie on the reservoir to determine the best placement of the well. In addition, the traditional gradient-based methods such as Line-search and Trust-region were not viable in terms of maximum results obtained. Gradient-based methods were too dependent on the surface gradient of the solution and may only converge to local optima instead of global optima. Complex reservoirs have rough surfaces with high uncertainties, which hinders the traditional gradient-based method from converging to global optima. Thus, genetic algorithms were utilized to automate the manual trial-and-error process and to overcome the limitations of the traditional gradient-based method. The objectives of this study were to analyse the effect of different initial well placement distributions, the number of random solution sizes, and the crossover rate on cumulative oil production. A synthetic reservoir model built using CMG Builder was used as the testing platform for the optimization problems. Well-placement parameterization and optimization set-up were carried out using the CMG CMOST optimization tool. The integration of CMG IMEX and CMOST optimized cumulative oil production based on the objectives of the study. The results obtained showed that the higher number of random solutions used resulted in higher cumulative oil production, with more generations needed to reach the optimum solution. It can be concluded that the larger number of random solutions used increased the probability of reaching the optimum solution, but will take more generations.

(1) Background: The aim of this study was to investigate the circadian rhythms of tongue features according to the effects of physiological phases over a 24-hour period. (2) Methods: Fifteen healthy participants aged 20 to 69 years were recruited. The participants did not have current chronic diseases or past diseases and had to meet the inclusion and exclusion criteria. The participants stayed at the Gil Hospital for a duration of 2 nights and 3 days. On the first day, at 18:00, they consumed their allocated portions of food and water and then completed a questionnaire. At approximately 21:00, their tongue images were acquired using a computerized tongue image acquisition system, following which they slept for 8 hours, commencing at 23:00. Measurements were taken from 07:00 through 21:00 on the second day, and the final acquisition was taken at 07:00 on the following morning, resulting in a total of eight images. The circadian rhythm was authenticated and quantified utilizing the single cosinor analysis, a technique for periodic regression analysis for fitting a 24-hour cosine curve. (3) Results: Cosinor analysis revealed that all tongue features were significantly related to circadian rhythm. (4) Conclusions: The results of this study may be important for considering the time of day at which the tongue is observed and tongue status is evaluated.

In this comprehensive review, we delve into the realm of intention recognition within the context of digital forensics and cybercrime. The rise of cybercrime has become a major concern for individuals, organizations, and governments worldwide. Digital forensics is a field that deals with the investigation and analysis of digital evidence in order to identify, preserve, and analyze information that can be used as evidence in a court of law. Whereas, Intention recognition is a subfield of artificial intelligence that deals with the identification of agents’ intentions based on their actions and change of states. In the context of cybercrime, intention recognition can be used to identify the intentions of cybercriminals and even to predict their future actions. Employing a meticulous six-step systematic review approach, we curated research articles from reputable journals and categorized them into three distinct modeling approaches: logic-based, classical machine learning-based, and deep learning-based. Notably, intention recognition has transcended its historical confinement to network security, now addressing critical challenges across various subdomains, including social engineering attacks, AI black box vulnerabilities, and physical security. While deep learning emerges as the dominant paradigm, its inherent lack of transparency poses unique challenges in the digital forensics landscape. We advocate for hybrid solutions that blend deep learning’s power with interpretability. Furthermore, we propose the creation of a comprehensive taxonomy to precisely define intention recognition, paving the way for future advancements in this pivotal field.

In the context of inclusive education, digitalization in higher education is designed to promote the ideals of cultural diversity, social inclusivity, and sustainable development through technological means. This study explores the strategies and practices of digitalization in achieving inclusive education goals in higher education, aiming to provide theoretical and empirical foundations for education policymakers, teachers, and technology developers. This study adopts a mixed-methods research design, combining quantitative and qualitative data analysis to assess the current state of digitalization in higher education from various perspectives, particularly its effectiveness in advancing educational inclusivity. Through surveys, in-depth interviews, and case studies, data were collected from teachers, students, and administrative personnel to reveal opportunities and challenges in digital education resources and practices. The results show that while digitalization has improved the accessibility of educational resources, facilitated information sharing and cultural exchange, there are still numerous challenges, such as unequal technology access, insufficient cultural sensitivity in content, and issues related to the depth and quality of online interactions. Furthermore, the study identifies key factors supporting inclusive education, including cross-cultural curriculum design, teacher professional development, and students' critical use of digital tools. Finally, the paper presents a series of strategic recommendations, including the development of multicultural education platforms, strengthening teacher training, and building an inclusive digital environment. These recommendations aim to promote a more coordinated and inclusive higher education digital ecosystem that emphasizes not only technological innovation but also humanistic care and social responsibility. Through these measures, digitalization in higher education can better serve individual growth and comprehensive societal development.

Diabetic foot ulcers (DFUs) significantly affect the lives of patients and increase the risk of hospital stay and amputation. We suggest a remote-monitoring platform for better DFU care. This system uses digital health metrics (scaled from 0 to 10, where higher scores indicate a greater risk of slow healing) to provide a comprehensive overview through a visual interface. The platform features smart offloading devices that capture behavioral metrics such as offloading adherence, daily steps, and cadence. Coupled with remotely measurable frailty and phenotypic metrics, it offers an in-depth patient profile. Additional demographic data, wound characteristics, and clinical parameters, such as cognitive function, were integrated, contributing to a comprehensive risk factor profile. We evaluated the feasibility of this platform with 124 DFU patients over 12 weeks; 39% experienced unfavorable outcomes such as dropout, adverse events, or non-healing. Digital biomarkers were benchmarked (0-10), categorized into low, medium, and high risk for unfavorable outcomes, and visually represented using color-coded radar plots. The initial results of case reports illustrate the value of this holistic visualization to pinpoint the underlying risk factors for unfavorable outcomes, including a high number of steps, poor adherence, and cognitive impairment. Although future studies are needed to validate the effectiveness of this visualization in personalizing care and improving wound outcomes, early results in identifying risk factors for unfavorable outcomes are promising.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

This paper describes the load capacity of short fiber-reinforced polymer lugs with Ti-6Al-4V selective laser-melted bushings with the original embedded element surface roughness and after sandblasting and vibratory finishing. Lugs are an important part of pin-joints. Adhesion between PA6 and SLM produced titanium is not fully studied. The cohesive zone material Mode II model parameters were calibrated experimentally by extruding a cylindrical bushing along the lug axis. The values of the maximum equivalent tangential contact stress were fitted for cases with investigated embed element roughness. The critical fracture energy for tangential slip was also estimated. Validation of the constructed CZM Mode II models with the results of strength experiments was performed. In both the experiment and the calculation, greater bushing roughness provides greater lug load-bearing capacity. The presented models can be used for the preliminary evaluation of SFRP PA6 parts with titanium embedded elements bearing capacity.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

Context: Despite the effort put into developing standards for structuring construction cost, and the strong interest into the field. Most construction companies still perform the process of data gathering and processing manually. That provokes inconsistencies, different criteria when classifying, misclassifications, and the process becomes very time-consuming, particularly on big projects. Additionally, the lack of standardization makes very difficult the cost estimation and comparison tasks. Objective: To create a method to extract and organize construction cost and quantity data into a consistent format and structure, to enable rapid and reliable digital comparison of the content. Method: The approach consists of a two-step method: Firstly, the system implements data mining to review the input document and determine how it is structured based on the position, format, sequence, and content of descriptive and quantitative data. Secondly, the extracted data is processed and classified with a combination of data science and experts’ knowledge to fit a common format. Results: A big variety of information coming from real historical projects has been successfully extracted and processed into a common format with 97.5% of accuracy, using a subset of 5770 assets located on 18 different files, building a solid base for analysis and comparison. Conclusion: A robust and accurate method was developed for extracting hierarchical project cost data to a common machine-readable format to enable rapid and reliable comparison and benchmarking.

Distributed/semi-distributed models are considered to be sensitive to the spatial resolution of the data input. In this paper, we take a small catchment in high urbanized Yangtze River Delta, Qinhuai catchment as study area, to analyze the impact of spatial resolution of precipitation and the potential evapotranspiration (PET) on the long-term runoff and flood runoff process. The data source includes the TRMM precipitation data, FEWS download PET data, and the interpolated metrological station data. GIS/RS technique was used to collect and pre-process the geographical, precipitation and PET series, which were then served as the input of CREST (Coupled Routing and Excess Storage) model to simulate the runoff process. The results clearly showed that, the CREST model is applicable to the Qinhuai catchment; the spatial resolution of precipitation had strong influence on the modelled runoff results and the metrological precipitation data cannot be substituted by the TRMM data in small catchment; the CREST model was not sensitive to the spatial resolution of the PET data, while the estimation fourmula of the PET data was correlated with the model quality. This paper focused on the small urbanized catchment, suggesting the influential explanatory variables for the model performance, and providing reliable reference for the study in similar area.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

The last-mile logistics in cities have become an indispensable part of the urban logistics system. This study aims to explore the effective selection of last-mile logistics nodes to enhance the efficiency of logistics distribution, strengthen the corporate distribution image, and further reduce corporate operating costs and alleviate urban traffic congestion. This paper proposes a clustering-based approach to identify urban logistics nodes from the perspective of geographic information fusion. This method comprehensively considers several key indicators, including the coverage, balance, and urban traffic conditions of logistics distribution. Additionally, we employed a greedy algorithm to identify secondary nodes around primary nodes, thus constructing an effective nodal network. To verify the practicality of this model, we conducted an empirical simulation study using the logistics demand and traffic conditions in the Xianlin District of Nanjing. This research not only identified the locations of primary and secondary logistics nodes but also provided a new perspective for constructing the urban last-mile logistics system, enriching the academic research related to logistics node construction. The results of this study are of significant theoretical and practical importance for optimizing urban logistics networks, enhancing logistics efficiency, and promoting the improvement of urban traffic conditions.

Radio Occultation (RO) is pivotal for profiling the neutral and ionized atmosphere, with the PlanetiQ mission, via its GNOMES satellites, striving to establish an advanced atmospheric observing system. However, an assessment of the spatiotemporal distributions of PlanetiQ observations and comparisons with reliable datasets are lacking. This study addresses this gap by examining the temporal and spatial distribution of RO observations from PlanetiQ during its initial 198 operational days in 2023, alongside comparisons with COSMIC and Numerical Weather Prediction (NWP) models. Data from GN02, GN03, and GN04 satellites, yielding 1099, 1313, and 1843 RO events per day respectively, were analyzed. The satellite constellation's observations demonstrate a generally well-distributed pattern, albeit minor deficiencies in equatorial and polar regions. Single-profile comparisons with COSMIC data reveal strong correlations for pressure, temperature, Water Vapor Pressure (WVP), and refractivity profiles, with temperature exhibiting larger variations (RMSE = 1.24°C). Statistical analyses confirm statistically insignificant differences between PlanetiQ and COSMIC profiles at the same spatio-temporal coordinates. Comparisons with NWP models show slight differences with GFS, with overall RMSE values of 0.23 mb (WVP), 0.6 mb (pressure), 1.3 (refractivity), and 1.5°C (temperature). However, assessments against GFS/ECMWF models indicate overall compatibility, with insignificant differences between PlanetiQ profiles and models observations.

DNA Topoisomerase IIa (Top2A) is a nuclear enzyme that is a cancer drug target, and there is interest in identifying novel sites on the enzyme to inhibit cancer cells more selectively and to reduce off-target toxicity. The C-terminal domain (CTD) is one potential target, but it is an intrinsically disordered domain, which prevents structural analysis. Therefore, we set out to analyze the sequence of Top2A from 105 species using bioinformatic analysis including the PSICalc algorithm, entropy analysis, and other approaches. Our results demonstrate that large (10th-order) interdependent clusters are found including non-proximal positions across the major domains of Top2A. Further, CTD-specific clusters of 3rd, 4th, and 5th-order were identified that included positions that had been previously analyzed via mutation and biochemical assays. Some of these clusters coincided with positions that when mutated either increased or decreased relaxation activity. Finally, sites of low entropy (i.e., high information content) were identified and mapped as key positions in the CTD. Included in the low entropy sites are phosphorylation sites and charged positions. Together, these results help to build a clearer picture of the critical positions in the CTD and provide potential sites/regions for further analysis.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

The use of haptic devices in rehabilitation of impaired limbs has become rather popular, given the proven effectiveness in promoting recovery. In a standard framework, such devices are used in rehabilitation centers, where patients interact with virtual tasks, presented on a screen. To track their sessions, kinematic/dynamic parameters or performance scores are recorded. However, as Internet access is now available at almost every home, and in order to reduce the hospitalization time of the patient, the idea of doing rehabilitation at home is gaining wide consent. Medical care programs can be synchronized with the home rehabilitation device; patient data can be sent to the central server that could redirect to the therapist laptop (tele-healthcare). The controversial issue is that the recorded data do not actually represent the clinical conditions of the patients according to the medical assessment scales, forcing them to frequently undergo clinical tests at the hospital. To respond to this demand, we propose the use of a bilateral master/slave haptic system that could allow the clinician, who interacts with the master, to assess remotely and in real time the clinical conditions of the patient that uses the home rehabilitation device as the slave. In this paper, we describe a proof of concept to highlight the main issues of such an application, limited to one degree of freedom, and to the measure of the stiffness and range of motion of the hand.

Digital twins are an emerging technology that could be harnessed for the digitalization of the industry. Steel industry systems contain a large number of electro-hydraulic components, as proportional valves. An input-output model for a novel water proportional cartridge valve is derived from physical modelling based on fluid mechanics, dynamics, and electrical principles. The valve is a two-stage valve with two 2/2-way water proportional valves as the pilot stage and a marginally stable poppet-type cartridge valve as the main valve. The orifice equation, which is based on Bernoulli principles, is approximated by a polynomial which makes parameter estimation easier and makes modelling possible without measuring pressure of the varying control volume situated in the pilot stage part of the valve. Data were collected when the valve was operating as a component in a closed-loop system as part of a press-mill machine in a steel manufacturing plant. Parameter estimation was made by convex optimization with physical constraints to overcome problems caused by poor system excitation. For comparison, a simple linear model was derived and the least squares method used for parameter estimation. A thorough estimation of the parameters relative errors is presented. The model contains 5 parameters related to the design parameters of the valve. The modelled position output is in good agreement with experimental data for training and test data. The model can be used for real time monitoring of the valve’s status by the model parameters. One of the model parameters varies linearly with production cycles. Thus, aging of the valve can be monitored.

The changing of banking customer preferences after Covid-19 pandemic encourages banking transformation. Neobanks emerges as innovation in banking that enter the market to compete with the incumbent banks by offering new digital experience for customer. This paper analyzes the neobanks which transformed from traditional bank, specifically its efficiency after they implement digital transformation. Efficiency is measured by using Stochastic Frontier Analysis (SFA). This study also uses Pooled Mean Group (PMG) of Panel ARDL (Autoregressive Distributed Lagged) to investigate digital transformation as one of determinants neobank’s efficiency, as well as to examine the existence of short-term and long-term relationship between digital transformation and efficiency. The SFA results show that the efficiency of the neobanks increase after they carry out digital transformation. Furthermore, from PMG Panel ARDL, it can be concluded that digital transformation is one of determinant of efficiency and there is longevity relationship between digital transformation and efficiency. In the short run, digital transformation has a significant and negative correlation with efficiency and in the long run, it has a significant positive relationship because initially digital transformation cost for operational and risk management innovation decreases the profit efficiency, but afterwards it increases the profit efficiency.

Bridges enable communications and transportation of goods nationally and internationally, underpinning economic and social activities, thus they are pylons of our prosperity and mobility. Bridges worldwide are constantly subjected to physical wear, ageing, deterioration, hazards, environmental influences, and increased loading. Loss of performance and functionality of bridge structures would have a crucial impact on overall infrastructural resilience and would cause significant negative economic and social consequences. Monitoring their behaviour for different loading conditions relies on accurate estimations of the stress-strain state of various critical components and remaining capacities. These activities are of high importance for better planning lifespan prolongation, that is the extension of their service life and prevention of unforeseen collapses, in line with sustainability principles of well-informed maintenance. In many cases, access to the structure is limited or even impossible, which causes the need for the deployment of remote and contactless methods. One such innovative technique, which has recently attracted attention in scientific and practical applications is the digital image correlation (DIC). DIC is a contactless approach applicable for long-term measurements, which enables obtaining the full field of strains and deformations. Although the DIC approach has been widely used in world engineering practice for monitoring bridges and has proved to be a reliable and accurate method, there is a lack of systematic integral review on previous practical applications, revealing limitations and perspectives. This is the main motivation and novelty of this study, which will describe selected case studies, in which DIC was used on real full-scale bridge structures and propose improvements for the method.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

Sustainability is a characteristic manifested in the ability to maintain the necessary level of performance for construction companies when risk factors arise during the implementation of investment and construction projects. The risk factors that arise during the implementation of in-vestment and construction projects differ in nature, degree of influence, and other characteristics. Ignoring these factors and measures to manage them often leads to critical consequences in the form of disruptions in the timing of work. Risk is a combination of the probability and consequences of the occurrence of adverse events. The article considers the concept of risk as a potential possibility of occurrence of adverse situations and related consequences when exposed to these factors. Risk factors are characterized by surprise, discreteness of changes, the presence of threshold values, upon reaching which a transition to a different mode of operation is required. The article discusses the risk factors arising at the construction stage, their classification. A methodology has been developed that includes conducting a survey in the form of a questionnaire in order to collect information about risk factors that affect the implementation of investment and construction projects. Experts with experience in the construction sector were involved in the survey. The processing of the survey results made it possible to assess the significance of various risk factors in investment and construction projects. Thus, statistical and expert methods were used in the study. The results showed that financial, technical, legal, economic, managerial and natural factors have the greatest impact on investment and construction projects. It is recommended to pay special attention to the listed factors when developing measures aimed at preventing risks and their consequences. The methodology described in the study can be used by construction companies in strategic planning. The analysis of the stability of construction companies, depending on their use of various ways to counteract risk factors, allowed us to develop a number of practical recommendations to reduce the impact of the studied factors on achieving the goals of investment and construction projects.

Abstract: Rural digital governance is an inevitable requirement to improve the efficiency of rural governance, and is also an important means to realize the modernization of rural governance. In the context of the digital rural development strategy, the index measurement system of rural digital governance level is built around five key governance areas of "digital economy, digital ecology, digital culture, digital people's livelihood, and digital government affairs". The entropy weight Topsis model is used to measure and evaluate the level of rural digital governance in 31 provinces in China in 2021. The results show that there is a large gap in the level of digital governance in China's counties and villages, and the level of each region presents a decreasing spatial distribution from "east - middle - west". In terms of digital economy, the eastern region has a high score and good development, while the central and western regions have poor development. In terms of digital ecology, only the eastern region is higher than the national average; In terms of digital culture, only the central region is higher than the national average; In terms of digital livelihood and digital government, the central and eastern regions are slightly higher than the national average; The top three provinces in overall scores are Zhejiang, Guangdong and Jiangsu.

The objective of this research is to establish a better understanding of the current landscape of digital learning research and sustainable development by using CiteSpace. First, we retrieved published publications from the Web of Science (2004–2022). Following that, we examined the primary research strengths and important subjects of digital learning from two perspectives: collaboration networks (including collaborative networks across countries, institutions, and authors) and co-citation networks. We examined the co-citation network from three perspectives: cluster analysis, the most active citers, top references. Furthermore, referenced journals, popular themes, and rising trends were examined. These findings indicate the primary study subjects in the field of digital learning, the most intriguing research literature, and each period's emerging research hotspots. Finally, we proposed further study ideas for future paths.

With the growing trend of urbanization and the growing number of people migrating to cities, the demand for the development and construction of new buildings as well as the infrastructure has risen, meaning that the construction industry must adapt to the trends. The growing demands with shorter deadlines for an industry already known for high costs and not delivering on time means that productivity must be increased without increasing the cost. The solution for this might lie in the application of the Lean philosophy to the construction industry. This paper analyses the application of the Lean philosophy in order to increase the productivity in the airport construction site. The paper highlights the potential for enhancing productivity in construction workplaces by concurrently fostering continuous improvement and sustainability through the implementation of the A3 methodology and Lean principles, resulting in waste reduction and increased value.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

Proposed study aims to investigate the digital transformation of Greek small and medium enterprises (SMEs), with a particular focus on their digital maturity and the strategic and organizational factors contributing to digital transformation. The research issue of digital transformation is attracting considerable interest among academics and business practicians since COVID-19 accelerated the procedure of implementing Industry’s 4.0 principles all over global economies. Quantitative research on 147 Greek SMEs revealed most important issues on how these businesses implement digital transformation, factors accelerating or decelerating the process, barriers and expected outcomes. Research enlights how SMEs face the transition to digital business and reveals the factors that can facilitate the whole process. Results can be valuable for stakeholders enabled to digital transformation process from both business and academic point of view, while there exist aspects that can contribute to policy makers / motivation developers in state’s level as well.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

Background: Learning arrangements in health care profession education are increasingly taking place in digital environments. VR in nursing education, as one of the digital elements, is the subject of controversial debate. On the one hand it supports the authenticity of case studies by adding realistic perspectives and information. On the other hand, the costs of developing and maintaining software and hardware hinder long-term implementation. Methods: In this paper, we describe our findings and insights from two different research projects focused on the incorporation of digital tools, particularly virtual reality (VR), into nursing education. Based on the German context, our aim is to promote the adoption of innovative digital methods in nursing education and to offer invaluable experiences from the field. Results: Starting with a brief recapitulation of the projects, we then elucidate the pedagogical strategies for embedding VR-driven scenarios in nursing education. Based on our experiences during the projects we identify various positive aspects, such as change of perspective and simulating acute situations. Key findings: Although potential drawbacks remain, we advocate long-term implementation and specific use of VR at the interface between theory and practice. Nevertheless it is crucial to establish regular evaluation observing the value of digitalisation, especially VR; for nursing education.

The global coronavirus (COVID-19) pandemic has created a whole new set of risks in construction industries generating unprecedented delays, disruptions, and uncertainty on construction projects, and has forced the industries in adopting more sophisticated technologies while combating the reduced workforce on job sites. Further, the post-pandemic era of construction is expected to be a lot different as the industries will embrace the technology as the augmentation and collaboration strategy. Thus, it will be extremely hard to sustain for construction industries in the absence of effective risk management. The existing risk plans need to be inspected for their capability of handling new risks arising from COVID-19 and the project managers will need to make the necessary revisions as needed. This paper discusses on past (NORM), present (NEW NORM), and future (Post COVID-19 NORM) of the construction industry and highlights key strategies for managing projects and construction risks during and post COVID-19 pandemic.

This article delves into the intersection of generative AI and digital twins within drug discovery, exploring their synergistic potential to revolutionize pharmaceutical research and development. Through various instances and examples, we illuminate how generative AI algorithms, capable of simulating vast chemical spaces and predicting molecular properties, are increasingly integrated with digital twins of biological systems to expedite drug discovery. By harnessing the power of computational models and machine learning, researchers can design novel compounds tailored to specific targets, optimize drug candidates, and simulate their behavior within virtual biological environments. This paradigm shift offers unprecedented opportunities for accelerating drug development, reducing costs, and, ultimately, improving patient outcomes. As we navigate this rapidly evolving landscape, collaboration between interdisciplinary teams and continued innovation will be paramount in realizing the promise of generative AI and digital twins in advancing drug discovery.

With the increase in technological advancements, architects and engineers over the past couple of decades have been trying to achieve high efficiency within construction projects. Their goals also include reducing global warming effects from construction and building new construction faster for the growing population in urban cities. This requires using a construction method that is less harmful to the environment and faster than other traditional methods. Modular construction, also known as modular construction, is the method that has the potential to make this happen. This review paper discusses what modular construction is and how it is different from the traditional on-site construction. Environmental impacts of using modular construction and what leads to it being more efficient and faster than on-site construction. The study doesn’t suggest that modular construction is the solution to all the problems being faced in the construction industry today, but it is a potential solution that if used in the right situation and correct manner, can have a huge positive impact on the construction industry.

Efficient fixed crane position analysis is critical in precast buildings construction to maximize lifting efficiency for precast elements. The primary objective is to minimize the travel distances of fixed cranes, thereby enhancing operational efficiency and cost control. This involves strategically reducing the distances between the transport truck parking, where elements are stored, the fixed crane, and the construction installation point. Despite its significance, existing studies often overlook the dynamic movement efficiency of transport trucks, particularly when dealing with multiple transport trucks and various models of fixed cranes, rendering the opti-mization of this scenario a challenging NP-hard problem susceptible to combinatorial explosion. This study presents a novel mathematical model leveraging the Genetic Algorithm (GA). The model aims to solve optimal model and position of fixed cranes, along with identifying ideal positions for transport truck parking. The study's methodology is validated and demonstrated through a project case study. Comparative analyses between the proposed model and the original planning underscore a noteworthy 6% reduction in both duration and costs when lifting elements directly from transport trucks, as opposed to establishing an on-site stock yard. Furthermore, the developed GA exhibits a substantial improvement in final solutions, achieving a remarkable 30% reduction in both operational duration and costs. This research contributes valuable insights into fixed crane position analysis of precast building construction, providing foundation for enhanced operational efficiency and cost-effectiveness in the industry.

Floods, recognized for their erratic behavior and devastating effects, are a significant threat as a natural disaster. In Brunei Darussalam, the impact of climate change is becoming increasingly evident through higher temperatures and an expected increase in annual rainfall (5.0mm per year from 2021 to 2050), highlighting the critical need for updated flood risk management techniques. In line with the climate resilience and adaptation objectives of WAWASAN 2035, this paper introduces an innovative approach—a cutting-edge flood risk management framework that utilizes the capabilities of big data analytics, sophisticated machine learning algorithms, and smart Internet of Things (IoT) sensors. Traditional methods, which rely on numerical and physical data modeling, often do not provide precise short-term flood forecasts. Our suggested framework uses machine learning to analyze real-time flood forecasting, sensor data and enhance warning systems, addressing the shortcomings of traditional approaches. The key advantage of this approach is its potential to drastically decrease flood-related damages, protect lives, and boost infrastructure resilience. This proposal is not only in aligns with Brunei's vision for a safe and climate-adaptable future but also marks a significant step forward in adopting innovative and sustainable flood risk management solutions amidst an evolving climate.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

In this paper, the authors seek to discuss some of the complexities involved in cross-cultural working in relation to the communication and management of pain in older people. Specifically, the paper addresses the culture construction of ageing and how pain is often constructed as a natural part of ageing. The authors also suggests that with the rise of the ideology of active-ageing many older people who are disabled or living in chronic pain, may feel a moral imperative to hide pain and ill-health. The discussion extends into looking at the impact of culture and the communication of pain, including specific idioms of distress, somaticize and the lay-management of pain through stoicism.

The massive amount of human biological, imaging and clinical data produced by multiple and diverse sources, necessitates integrative modeling approaches able to summarize all this information into answers to specific clinical questions. In this paper, we present a hypermodeling scheme able to combine models of diverse cancer aspects regardless of their underlying method or scale. Describing tissue-scale cancer cell proliferation, biomechanical tumor growth, nutrient transport, genomic-scale aberrant cancer cell metabolism, and cell signaling pathways that regulate the cellular response to therapy, the hypermodel integrates mutation, miRNA expression, imaging, and clinical data. The constituting hypomodels as well as their orchestration and links are described. Two specific cancer types, Wilms tumor (nephroblastoma) and non-small cell lung cancer, are addressed as proof of concept study cases. Personalized simulations over the actual anatomy of a patient have been carried out. The hypermodel has also applied to predict tumor control after radiotherapy and the relationship between tumor proliferative activity and response to neoadjuvant chemotherapy. Our innovative hypermodel holds promise as a digital twin based clinical decision support system and the core of future in silico trial platforms, although additional retrospective adaptation and validation is necessary.

In recent years, the digital economy has played an increasingly important role in enhancing productivity, fostering growth, and facilitating the emergence of digital banking. With the widespread adoption of digital financial services for financial inclusion, the banking sector is experiencing a demand for digital transformation. It is important to note that despite the many advantages of this change, it also disrupts the familiar banking experience that customers have grown to expect, as well as introducing potential risks to maintaining customer protection at previous levels. Many critics have raised concerns regarding customer protection and potential exposure to various risks that may arise from digital financial services, which may result in both financial and non-financial losses. These risks can impact customer retention as dissatisfied customers may switch to alternative service providers. Additionally, reputation can be affected since merely offering digital financial services may not sufficiently safeguard customers. To remain competitive, financial institutions must deliver a secure experience that aligns with customer expectations while considering economic factors and societal needs. This is why it is essential to comprehend the severity of the risk factors that influence the protection of customers in the realm of digitalized banking services and products. In this study, five factors have been identified that influence customer protection when using digital financial services in Pakistan. Based on the analysis conducted using SmartPLS, it appears that all the factors proposed in this study have a significant and positive impact on the protection of customers. In particular, the information provided remains of paramount importance when it comes to determining the level of protection that a customer is entitled to within digital financial services, followed by responsiveness, privacy, authentication, and encryption mechanisms. Due to these findings, the implementation of enhanced information security management principles becomes imperative for the development and progress of the Pakistani digital banking industry.

This paper provides an overview of the current state-of-the-art digital twin and digital thread technology in industrial operations. Both are transformational technologies that have the advantage of improving the efficiency of current design and manufacturing. Digital twin is an important element of the Industry 4.0 digitalization process; however, the huge amount of data that are generated and collected by digital twin offer challenges in handling, processing and storage. The paper aims to report on the development of a new framework that combines the digital twin and digital thread for better data management in order to drive innovation, improve the production process and performance, and to ensure continuity and traceability of information. The digital twin/thread framework incorporated behavior simulation and physical control components, in which these two components rely on the connectivity between the twin and thread for information flow and exchange to drive innovation. The twin/thread framework encompasses specifications that include organizational architecture layout, security, user access, cloud computing set-up, and hardware and software requirements. It is envisaged that the framework will be applicable to enhancing optimization of operational processes and traceability of information in the physical world, especially in Industry Shipyard 4.0.

Based on screening in computational biology and biological in vitro assays, five natural products isolated from extracts of the herbal medicine toad skin, such as cinobufagin (CBFi), bufalin (BFi), arenobufagin (ABFi), telocinobufagin (TBFi), bufotalin (BFTi), were subjected to molecular docking calculations with the use of SARS-CoV-2 main protease (PDB 6LU7 and 7BTF) and top-scoring ligand-receptor complexes were obtained. The results showed that the binding energy of ABFi to the 3CL protein was -17.044kcal/mol, which was higher than CBFi and TBFi. However, the binding energy of ABFi to the RdRp protease was -23.250 kcal/mol, which was much lower than that of CBFi and TBFi, EVEN lower than that of ABFi to the 3CL protein. ABFi also has polar interactions with amino acids such as Glu811, Ser814, Ser681 and Thr680 of RdRp enzyme. The results revealed that ABFi had a moderate inhibitory effect on the cell proliferation of SARS-CoV-2 in vitro, with an inhibition rate of 61.12%, even weaker than Remdesivir. This new discovery provides us with new ideas for in-depth studies on the development of natural products with this class of structural generalizations as inhibitors of SARS-CoV-2, and provides an experimental basis for the next step of mechanistic studies.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

This paper discusses the design and implementation of a portable IoT station. Communication and data synchronization issues in several installations are addressed here, making possible a detailed analysis of the entire system during its operation. The system proposed is interpreted as an additional tool which can be utilized in several applications, where the system operator requires a synchronized data stream, combining multiple communication protocols into one single time stamp. The hardware selected for the portable IoT station complies with the International Electrotechnical Commission (IEC) industrial standards. A short discussion regarding interface customization shows how easily the hardware can be modified so that it is integrated with almost any system. A Programmable Logic Controller enables the Node-Red to be utilized. This open-source programming tool employs flows to define operations for each global variable nominated in the Modbus register. Two applications are presented and discussed in this paper, each application has a distinct methodology utilized to publish and visualize the acquired data. The portable IoT Station is highly customizable, consisting of a modular structure and providing the best platform for future research and development of dedicated algorithms.

With the growing of university chemistry experiment projects, scientific research personnel, specialized equipment, laboratory accident is increasing yearly. And accident data lacks a safety platform to store related information and cannot be guaranteed for efficient conditional sharing. To solve these problems, we designed a laboratory accident system to store, share related data and predict risk level. In this paper, we manually collected chemistry laboratory accidents by python software and class assignments, then analyses risk factor variables using Spsspro, finally established a prediction model using Stata. We intended to register laboratory related data into proposed chemistry accident system based on data ownership safety architecture. The chemistry accident system can break data barriers using confirmation and authorization key technology to trace non-tampered data source in real time when emergency accident happens. Meanwhile, our proposed system can use our designed accident risk model to predict risk level of any experiment project. It can also recommend appropriate safety education models.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

There is no doubt that the COVID-19 pandemic has greatly affected the higher education sector in South Africa. However, academics and students’ preparedness and competencies have been considered a major conundrum concerning the integration of online learning in the classroom. The purpose of this paper is to examine the academics’ perspectives on a blend of a metaverse in the higher education sector in the post-COVID-19 era at one of the South African rural-based universities. A survey was administered in 2022 to ten (10) academics and the reports were consulted from four (4) E-learning practitioners to solicit their perceptions regarding the use of online learning and contact classes in the post-pandemic era. A qualitative research approach was employed to comprehend the challenges encountered in a historically disadvantaged rural-based university in Limpopo Province. The findings of this study show that there are major issues and challenges impeding the establishment of effective e-learning education. Consequently, technological continuity as a new normal in the post-COVID-19 era appears to be unattainable due to the challenges encountered by the students and lecturers. The use of Learning Management Systems among academics seems to have deteriorated due to the adjustments in COVID-19 rules and regulations. Furthermore, the findings revealed that most academics believed that contact learning remains irreplaceable throughout generations and ages as some are technophilic. This paper recommends that the incompetence and technological resistance and reluctance in adopting transformative pedagogies may not be used as a stumbling block to consider e-learning as a viable option to discontinue online education.

Sepsis is a serious disease that can lead to mortality. The etiology of the disease is connected to how the body as a host reacts toward microbes such as bacteria, viruses, and fungi invasion. Current research shows that during sepsis, the reaction toward microbe attacks takes two main phases. The first is known as a cytokine storm, while the second is a vicious cycle of pro-inflammatory responses followed by a strict anti-inflammatory response led by CD4+ Tregs. Various immunomodulatory therapies have been proposed to break the cycle of pro- and anti-inflammatory reactions to sepsis. However, clinical trials did not show promising results, indicating further research into the mechanism that Treg uses to inhibit proinflammatory reactions. We used next-generation sequencing (NGS) analysis of bulk RNA-seq and single-cell RNA-seq data to examine the exact molecular pathways used by Treg to inhibit the immune response in sepsis. Our approach identified ACOD1 (Aconitate Decarboxylase 1) as a primary mediator of Treg suppression of immune cells. We identified and validated CD36 as a downstream target of ACOD1. CD36 is a known metabolite regulator in Tregs. Taken together, our results indicate that targeting ACOD1 could prove valuable in regulating Treg function during sepsis.

After proving, in a purely categorial way, that the inclusion functor InAlg(Σ) from Alg(Σ), the category of many-sorted Σ-algebras, to PAlg(Σ), the category of many-sorted partial Σ-algebras, has a left adjoint FΣ, the (absolutely) free completion functor, we recall, in connection with the functor FΣ, the generalized recursion theorem of Schmidt, which we will also call the Schmidt construction. Next we define a category Cmpl(Σ), of Σ-completions, and prove that FΣ, labeled with its domain category and the unit of the adjunction of which it is a part, is a weakly initial object in it. Following this we associate to an ordered pair (α,f), where α=(K,γ,α) is a morphism of Σ-completions from F=(C,F,η) to G=(D,G,ρ) and f a homomorphism in D from the partial Σ-algebra A to the partial Σ-algebra B, a homomorphism ΥαG,0(f):Schα(f)B. We then prove that there exists an endofunctor, ΥαG,0, of Mortw(D), the twisted morphism category of D, thus showing the naturalness of the previous construction. Afterwards we prove that, for every Σ-completion G=(D,G,ρ), there exists a functor ΥG from the comma category (Cmpl(Σ)↓G) to End(Mortw(D)), the category of endofunctors of Mortw(D), such that ΥG,0, the object mapping of ΥG, sends a morphism of Σ-completion in Cmpl(Σ) with codomain G, to the endofunctor ΥαG,0.

This study aimed to identify the influencing factors that drive the adoption of smart construction technologies by highway construction companies. Using expert interviews and expert scoring, interview data were collected from 25 experts in the field, and the TOSE framework was proposed based on the TOE framework, identifying four dimensions and fourteen influencing factors. The results were analyzed using the Fuzzy-DEMATEL-ISM method, and the findings were then summarized according to the evaluation criteria to determine the validity of the fourteen hypotheses and the extent to which they drive the adoption of intelligent construction technologies by motorway construction companies. The findings of this paper will be of great value to decision-makers and participants in highway construction companies, as well as to other companies in the construction industry, in their decision to adopt smart construction technologies.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

As technology and multimedia production have advanced, there has been a significant rise in attacks on digital media, resulting in duplicated, fraudulent, and altered data and the infringement of copyright laws. This paper presents a robust and secure digital image watermarking technique that has been implemented in the spatial domain and exploits the erratic and chaotic behaviour of the powerful elementary cellular automata rule-30. The crucial characteristics of the watermarking system, i.e., imperceptibility, capacity, and robustness, have been perfectly balanced by the suggested blind watermarking technique. In this approach, prior to embedding, the grayscale watermark image is downsized to its two Most Significant Bits (MSBs). Then, the 2-MSBs watermark is encrypted using an ECA rule-30 so as to level up the security attribute of the system. Then, the host image is scrambled using ECA rule-30 to distribute the watermark pixels throughout the host image and thus achieve the highest robustness against geometrical attacks. Finally, the encrypted watermark data is embedded into the scrambled host image using the ECA rule-30-based embedding key. The proposed method performs better in terms of imperceptibility, capacity, and robustness when compared to several systems with similar competencies. The simulation's findings demonstrate strong imperceptibility as evaluated by the Peak Signal-to-Noise Ratio (PSNR), which has an average value of 58.3735 dB and a high payload. The experimental outcomes, observed across a diverse range of standardized attack scenarios, unequivocally establish the ascendancy of the proposed algorithm over competing methodologies in the realm of image watermarking.

Based on the data of A-share listed companies in Shanghai and Shenzhen of China from 2011 to 2018 and the digital inclusive finance index of Peking University (2011-2018), this paper empirically tests the impact of digital finance development on corporate social responsibility in various provinces of China and its impact mechanism. The results show that: (1) the development of digital finance helps to promote the fulfillment of corporate social responsibility; (2) the influence mechanism of the development of digital finance to promote the fulfillment of corporate social responsibility lies in that it reduces the cost of debt financing and leads to the improvement of corporate social responsibility.(3) Further research shows that the positive relationship between digital finance and corporate social responsibility is more significant in private enterprises. At the same time, the impact is more significant in areas with poor market environment. The above research shows that the development of digital finance has a significant positive effect, which will improve the level of corporate social responsibility.

There are clear signs that the COVID-19 pandemic has had a straining impact on the higher education sector in South Africa and the far reaches of the world. This chapter examines (Science, Technology, Engineering, Mathematics) STEM lecturers’ experiences with digital assessments and perspectives on the continuity of digital transformation in the higher education sector in the post-COVID-19 era at one of South Africa’s rural universities. In 2022, a survey of ten (10) lecturers was conducted and the reports were also consulted by four (4) e-learning practitioners to obtain their views on the use of online learning and contact courses in the post-pandemic period. A qualitative research approach was used to understand the puzzling issues faced by STEM lecturers at a previously disadvantaged institution in Limpopo Province. The results of this study show that there is a puzzling conundrum that hinders the integration of effective online learning. Furthermore, online education as the new normal in the post-COVID-19 era seems unattainable due to extremely complex and difficult-to-understand mathematical symbols. Software and tools proved to be limitations in terms of establishing an interactive learning environment for students and lecturers on online learning platforms. Lecturers’ use of learning and teaching platforms deteriorated due to numerous unknown challenges, but also the tightening of COVID-19 restrictions. Furthermore, the results showed that science and mathematics lecturers believe that contact learning remains irreplaceable across generations and eras as some are not technology enthusiasts. This paper recommends that the lack of technological systems as well as technological resistance and reluctance to adopt transformative pedagogy and innovative practices, should not be viewed as a thorny issue to end the dominance of online education in STEM courses. Keywords: connectivism, Learning Management Systems, affordances, technological resistance, Moodle, transformative pedagogy

In an era driven by technology and connectivity, where the sphere of learning goes beyond conventional classrooms, e-Service-Learning (e-SL) merges the possibilities of technology with the principles of experiential education in a powerful blend [1]. Service-learning (SL) is an educational proposal that has been cited by UNESCO [2] as an innovative educational tool through which to address the complex challenges of our society. The Sustainable Development Goals [3] provide a framework around which to structure the SL projects and thus develop the skills needed to act on the full range of goals. Embedding digital means open a debate on the intricate relationship between technology, education, and societal impact [4]. By analyzing two focus groups involving faculty, students and community partners, this contribution aims to explore the potential of combining SL and digital empowerment (DE). The focus group participants discussed the opportunities for innovation, the expected impact on them and the society at large, their needs and the pre-conditions needed to make SL and DE successful, and limitations. The results are presented according to the six principles of sustainability education in the university environment, highlighting the transformative potential of combining these principles within SL and DE.

The most popular schemes of digital potentiometers (DP) and digital-to-analog converters (DAC) are considered. DP and DAC use how elements of parameter adjustment of active RC-filters. The circuits of the DAC on the Kelvin-Varley divider, the Kelvin divider based on the R-2R matrix, and the architecture of the DAC with a segmented circuit are shown. The internal structure of DP an Analog Devices and Intersil company is shown, and also the DP switching circuits in a tunable low-pass filter and a band-pass filter, a programmable inverting amplifier and a voltage regulator are presented.

(1) Background: The purpose of this study is to evaluate the full arch scan accuracy (precision and trueness) of nine digital intra-oral scanners and four lab scanners. Previous studies have compared the accuracy of some intra-oral scanners, but as this is a field of quickly developing technologies, a more up-to-date study was needed to assess the capabilities of currently available models.; (2) Methods: The present in vitro study compared nine different intraoral scanners (Omnicam 4.6; Omnicam 5.1; Primescan; CS 3600; Trios 3; Trios 4; Runyes; i500 and DL206) as well as four lab light scanners (Einscan SE; 300e; E2 and Ineos X5) to investigate the accuracy of each scanner by examining the overall trueness and precision. Ten aligned and cut scans from each of the intra-oral and lab scanners in the in vitro study were brought into CloudCompare. A comparison was made with the master STL using the CloudCompare 3D analysis best-fit algorithm. The results were recorded along with individual standard deviation and a colorimetric map of the deviation across the surface of the STL mesh; a comparison was made to the master STL, quantified at specific points. ; (3) Results: In the present study, the Primescan had the best overall trueness (17.3 ± 4.9). Followed by (in order of increasing deviation) the Trios 4 (20.8 ± 6.2), i500 (25.2 ± 7.3), CS3600 (26.9 ± 15.9), Trios 3 (27.7 ± 6.8), Runyes (47.2 ± 5.4), Omnicam 5.1 (55.1 ± 9.5), Omnicam 4.6 (57.5 ± 3.2) and Launca DL206 (58.5 ± 22.0). Regarding the lab light scanners, the Ineos X5 had the best overall trueness with (0.0 ± 1.9). Followed by (in order of increasing deviation) the 3Shape E2 (3.6 ± 2.2), Up3D 300E (12.8 ± 2.7), and Einscan SE (14.9 ± 9.5); (4) Conclusions: This study confirms that all current generations of intra-oral digital scanners can capture a reliable, reproducible full arch scan in dentate patients. Out of the intra-oral scanners tested, no scanner produced results significantly similar in trueness to the Ineos X5. However, the Primescan was the only one to be statistically of a similar level of trueness to the 3Shape E2 lab scanner. All scanners in the study had mean trueness of under 60-micron deviation. While this study can compare the scanning accuracy of this sample in a dentate arch, the scanning of a fully edentulous arch is more challenging. The accuracy of these scanners in edentulous cases should be examined in further studies.

Published data or available literature on sustainable building plan-design, construction, performance, and renovation criteria have covered some stages or some parts of each stage. These data usually have been published partially in many different papers―there have not been any papers that published these data together. Hence, this paper aims to collectively review these data and publish them together. The collection and review of these data were carried out by our twenty-five team members who specialized in sustainable urban, architectural, and civil engineering and construction management. The gathered and reviewed outputs were combined and validated based on a general group consensus. This consensus decision-making proceeded through two major group meetings with several follow-up meetings. The first major meeting was to combine and improve the gathered reviewed sustainable building criteria for Cambodia. The second major meeting was to validate the improved reviewed sustainable building criteria for Cambodia. The several follow-up meetings were to discuss the relevance and importance of the validated data “criteria and their classifications and descriptions” in all stages and more focused on their importance and applicability to Cambodia. The collective reviewed data in this paper would be useful to researchers in the fields. They could also be useful collective knowledge and information for policymakers from governmental agencies and development partners, particularly for sustainable building and construction companies.

The focus of research has mainly been on the life cycle approach to project development, while limited attention has been given to the ageing construction companies that make all these activities/processes happen. This paper examines the organisational factors determining the sustainability and growth of building and civil engineering contractors in South Africa. The paper explores whether there are specific organisational factors that aid the sustainable development and growth of contractors in the South African construction industry. The paper analyses data gathered from face-to-face interviews conducted with four established and twelve upgraded and successful building and civil engineering contractors listed on the Construction Industry Development Board’s (cidb) Register of Contractors. The aim of the study is to identify the organisational factors critical for sustainable contractor development and growth in South Africa. The study found that organizational factors responsible for the sustainable development and growth of construction contractors include the size of the founding team members, management capabilities, strategic decisions made by founders/leaders and the ability of the company to constantly evolve, adapt and respond effectively to threats/challenges whenever they surface, amongst other findings. Capacity to generalise the results of the study to the large cidb registered contractor group is limited by the smallness of the sample size. Future research should make use of a larger sample size to obtain more general findings. The results of the study imply that the founding team size, experience, entrepreneurial and managerial capabilities, capacities and organisational structures that enable the efficient response of companies to external and internal challenges are key components of the definable arrangements that will support the sustainability and growth of construction organisations. The paper is of value to government departments and agencies such as the cidb and contracting firms in the construction industry.

Abstract-Digital Phase Plane is presented in this paper. For constant input second order digital systems with arbitrary initial conditions for arbitrary quantizaters, this digital phase plane shows, in plot form, the state trajectory and the asymptotic stability, including the existence and the position of arbitrary period limit cycles.

Failure to meet the deadlines for the implementation of investment and construction projects is a problem in all countries of the world, and leads to unstable activity of construction companies. The article studies the most important destabilizing factors affecting the main indicator of sustainable activity of construction companies-the duration of the implementation of an investment and construction projects. To determine and assess the impact of destabilizing factors on the duration of implementation of selected investment and construction projects, a survey was conducted, in which a number of customers, consultants and contractors involved in construction projects took part. Questionnaires developed on the basis of a cluster sample were sent to respondents, 48 responses were received in response to the assessment of destabilizing factors. To analyze the received and grouped information, structural equation modeling using the Smart-PLS program was used. As a result of modeling, a number of results were obtained, the most important of which are the identification of the main reasons that lead to an average (20% - 50%) increase in the duration of projects in the construction sector. The most significant were: the lack of an appropriate procurement program for materials; inefficient scheduling by contractors and instability of construction production; poor-quality processing of incoming information and untimely deci-sion-making due to changes in projects during their implementation. Destabilizing factors con-tribute to an increase in the duration of construction sector projects, which leads to time overruns, cost overruns, and an increase in the negative impact on the overall use of resources. As a result of the study, a set of recommendations was formed, the most important of which is the use of possible compensatory measures that can allow construction companies to eliminate the risks of disrupting construction deadlines for sustainable activities. These compensatory measures include: - recommendations to customers of the construction project; - recommendations to contractors; - recommendations to the consultant. Moreover, the control of destabilizing factors that can cause delays, the improvement of contracts and the precise and clearer definition of all elements of the project can help to reduce the duration of construction, and will allow companies to maintain sustainable activities in the construction industry.