We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

A new low-pass filter (LPF) circuit with independent adjustment of various, incl. digitally controlled, pole frequency resistors, pole quality factor and transmission coefficient. The proposed low-pass filter is based on the use of the properties of a multi-differential operational amplifier that performs the functions of a signal adder. The peculiarity of the filter is that it has three inputs, with respect to which different transmission coefficients are implemented, incl. inverting (-1) and non-inverting (+1). To check these properties of a low-pass filter in the Micro-Cap environment, computer simulation of a specific circuit was performed on a multi-differential operational amplifier AD 8130. Mathematical expressions are given for the main parameters of the proposed low-pass filter, which allow parametric synthesis of elements of a specific circuit under given restrictions on the used element base.

A new circuit of a low-pass filter (LPF) is considered, which is switched on at the input of analog-to-digital converters to limit the spectrum of input signals. The peculiarity of the proposed low-pass filter is the independent adjustment of the pole frequency, the quality factor of the pole and the transmission coefficient by different resistors. Computer simulation performed in the Micro-Cap environment confirms these properties of the LPF. The basic mathematical expressions are obtained, which make it possible to carry out the parametric synthesis of the LPF circuit. It is shown that the sensitivity of the LPF transmission coefficient to changes in the parameters of the frequency-setting elements of the circuit is close to zero and depends only on the ratio of the resistances of the two resistors in the feedback circuit.

In this paper, we continue the research cycle on the properties of convolutional neural network-based image recognition systems and ways to improve noise immunity and robustness [1]. Currently, a popular research area related to artificial neural networks is adversarial attacks. The effect of adversarial attacks on the image is not highly perceptible to the human eye, also it drastically reduces the neural network accuracy. Image perception by a machine is highly dependent on the propagation of high frequency distortions throughout the network. At the same time, a human efficiently ignores high-frequency distortions, perceiving the shape of objects as a whole. The approach proposed in this paper can improve the image recognition accuracy in the presence of high-frequency distortions, in particular, caused by adversarial attacks. The proposed technique makes it possible to measure up the logic of artificial neural network to that of a human, for whom high-frequency distortions are not decisive in object recognition.

Surface water distribution extracted from remote sensing data has been used in water resource assessment, coastal management, and environmental change studies. Traditional manual methods for extracting water bodies cannot satisfy the requirements for mass processing of remote sensing data; therefore, accurate automated extraction of such water bodies has remained a challenge. The histogram bimodal method (HBM) is a frequently used objective tool for threshold selection in image segmentation. The threshold is determined by seeking twin peaks, and the valley values between them; however, automatically calculating the threshold is difficult because complex surfaces and image noise which lead to not perfect twin peaks (single or multiple peaks). We developed an operational automated water extraction method, the modified histogram bimodal method (MHBM). The MHBM defines the threshold range of water extraction through mass static data; therefore, it does not require the identification of twin histogram peaks. It then seeks the minimum values in the threshold range to achieve automated threshold. We calibrated the MHBM for many lakes in China using Landsat 8 Operational Land Imager (OLI) images, for which the relative error (RE) and squared correlation coefficient (R2) for threshold accuracy were found to be 2.1% and 0.96, respectively. The RE and root-mean-square error (RMSE) for the area accuracy of MHBM were 0.59% and 7.4 km2. The results show that the MHBM could easily be applied to mass time-series remote sensing data to calculate water thresholds within water index images and successfully extract the spatial distribution of large water bodies automatically.

The most popular schemes of digital potentiometers (DP) and digital-to-analog converters (DAC) are considered. DP and DAC use how elements of parameter adjustment of active RC-filters. The circuits of the DAC on the Kelvin-Varley divider, the Kelvin divider based on the R-2R matrix, and the architecture of the DAC with a segmented circuit are shown. The internal structure of DP an Analog Devices and Intersil company is shown, and also the DP switching circuits in a tunable low-pass filter and a band-pass filter, a programmable inverting amplifier and a voltage regulator are presented.

Low-complexity ultrasound systems are increasingly desired for wearable point-of-care ultra-sound and massive-channel ultrasound for 3-D matrix imaging. However, the system complexity is closely associated with the imaging capabilities, remaining as a challenge. To resolve this limitation, this study revisits the general structures of analog and digital beamformers and in-troduces a hybrid approach to implement efficient ultrasound systems. The suggested hybrid beamforming takes two stages, where the first analog stage partially beamforms M-channel RF signals to N sum-out data (M-to-N beamforming), and the second digital stage beamforms N partial sums to single final beamformed data (N-to-1 beamforming). Our approach was systematically designed and implemented, which was demonstrated with a customized 64-channel 1-D phased array using a tissue mimicking phantom. The demonstrated results indicate that the analog-digital hybrid beamforming can be applied to any kind of arrays for sophisticated 3-D imaging and tiny wearable ultrasound applications.

In order to solve the problems of waveform distortion and signal delay by many physical and electrical systems with linear low-pass transfer characteristics with multiple complex poles, a general digital-signal-processing (DSP)-based method of real-time recovery of the original source waveform from the distorted output waveform is proposed. From the convolution kernel representation of a multiple-pole low-pass transfer function with an arbitrary denominator polynomial with real valued coefficients, it is shown that the source waveform can be accurately recovered in real time using a particular moving average algorithm with real-valued DSP computations only, even though some or all of the poles are complex. The proposed digital signal recovery method is DC-accurate and unaffected by initial conditions, transient signals, and resonant amplitude enhancement. This method can be applied to most sensors and amplifiers operating close to their frequency response limits or around their resonance frequencies to accurately deconvolute the multiple-pole characteristics and to improve the overall performances of data acquisition systems and digital feedback control systems.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

Self-compacting concrete (SCC) is a high-quality construction solution combining high fluidity, passing and filling ability with improved mechanical properties and durability. In the present study, the effect of incorporating alternative waste materials, such as two by-products of the ce-ment industry, namely cement kiln dust (CKD) and by-pass dust (BPD), into SCC as partial re-placement for traditional filler material was investigated. The produced compositions were compared with reference mixtures containing only marble powder (MP) as a filler. A series of tests including specific test methods for wet SCC, compressive, flexural and tensile splitting strength tests as well as drying shrinkage determination were conducted to evaluate the quality of the produced SCC in terms of fresh and hardened SCC properties. The use of alternative fine filler materials resulted in a high-performance sustainable SCC of low cement content. Specifi-cally, incorporating CKD into the SCC enhanced its rheological behavior and improved slightly its mechanical properties, while the use of BPD led to SCC mixtures of adequate rheological characteristics but with highly upgraded mechanical and physical properties

Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

High-performance motor drives that operate in harsh conditions require an accurate and robust angular position measurement to correctly estimate the speed and reduce the torque ripple produced by angular estimation error. For that reason, a resolver is used in motor drives as a position sensor due to its robustness. A resolver-to-digital converter (RDC) is an observer used to get the angular position from the resolver signals. Most RDCs are based on angle tracking observers (ATOs). On the other hand, generalized predictive control (GPC) has become a powerful tool in developing controllers and observers for industrial applications. However, no GPC-based RDC with zero steady-state error during constant speed operation was proposed. This paper proposes an RDC based on a second-order difference GPC (SOD-GPC). In SOD-GPC, the second-order difference operator is applied to design a GPC model with two embedded integrators. Thus, the SOD-GPC is used to design a type-II ATO whose steady-state angle estimation error tends to zero during constant speed operation. Simulation and experimental results prove that the proposed RDC system has better performance than other literature approaches.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

The traditional manual recording of vaccination records in Germany faced challenges during the COVID-19 pandemic, prompting the introduction of a Covid smartphone app with QR codes. However, this solution brought new challenges, emphasizing the need for a centrally managed European digital vaccination record for efficiency and validity. Thus, this study assesses the feasibility of using the HL7 FHIR standard in the healthcare industry for implementing a digital vaccination pass management and monitoring system. The system aims to offer convenience and improved efficiency for both patients and healthcare providers while promoting interoperability with other healthcare systems. We developed a prototype using modern technologies, such as React, Quarkus, and Keycloak, evaluating the applicability of FHIR in promoting interoperability within the healthcare industry. Results indicate potential benefits for patients and healthcare providers, offering secure access to immunization records, personalized recommendations, and streamlined management. However, challenges in integrating nuanced vaccination processes into the standardized FHIR system, necessitating custom extensions, and issues with manual data entry and identity provider integration, pose obstacles. Despite these challenges, the study suggests that implementing HL7 FHIR can enhance efficiency, data accessibility, and accuracy in the vaccination process, supporting broader digitization efforts in the German healthcare system and beyond.

This paper presents a compact wideband circularly polarized cross dipole antenna with low-pass filter response. It consists of two pairs of folded crossed dipole arms printed separately on both sides of the top substrate, and the two dipole arms on the same surface are connected by an annular phase-shifting delay line to generate circular polarization. A bent metal square ring and four small metal square rings around the cross dipoles are employed to introduce new resonant frequencies, effectively extending the impedance and axial ratio bandwidth. Four square patches printed on the middle substrate are connected to the ground plane by the vertical metal plates, in order to reduce the antenna height. Thus, a compact wideband circularly polarized antenna is realized. In addition, a transmission zero can be introduced at the upper frequency stopband by the bent metal square rings, without using extra filter circuits. For verification, the proposed model is implemented and tested. The overall size of the model is 90mm×90mm×33mm(0.37λ0×0.37λ0×0.14λ0, λ0 denotes the center operating frequency). The measured impedance bandwidth and 3 dB axial ratio bandwidth are 53.3% and 41%, respectively. More than 15 dB upper-band radiation suppression level is realized, indicating a good low-pass filter response.

The VLSI industry is facing parasitic effects that trouble development in the nanoscale domain. However, instead of replacing the traditional MOSFET design, it would be more advantageous to apply different doping profiles and discerning which deal with specific parasitic effects the best. With a review of Gaussian doping, Uniform doping, and Delta doping profiles and analysis of the FET technology characteristics that use these doping profiles, a comparison can be made among them for integrated circuit design engineers. These doping profiles are compared based on how well they perform against non-ideal and ideal environments. Also, both digital and analog performance are measured to ensure the uniqueness of each doping profile that is present. After getting a list of benefits from each doping profile, it is derived to determine which doping profile works best against a host of parasitic effects and what type of application do these doping profiles have

This paper presents a study of the 2D roughness profiles on a flat surface generated on a steel work piece, by ball nose end milling, with linear equidistant tool paths (pick-intervals). The milled surface exploration with a surface roughness tester (on pick and feed directions) produces usually 2D roughness profiles having periodical evolutions. These evolutions can be seen as time-dependent signals, describable as a sum of sinusoidal components (the wavelength of each component being regarded as a period). In order to detect a well approximated description of these components, two appropriate signal processing techniques are used in this work: first technique provides a direct mathematical (analytical) description and is based on computer aided curve (signal) fitting (more accurate), the second technique (providing an indirect and incomplete description) is based on the spectrum generated by fast Fourier transform (less accurate). This study can be seen as a way for a better understanding the interaction between the tool and the work piece or to achieve a mathematical description of the machined surface microgeometry in terms of roughness (e. g. its description being a collection of closely spaced 2D roughness profiles).

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

This article presents a decentralized phase-shedding technique for multiphase converters. The usual central digital controller is replaced by identical local controllers forming a daisy-chain structure. Phase-shedding decisions are taken locally based on a local inductor current monitoring and threshold crossing management. This control strategy allows to implement as many phases as desired in a modular manner. In order to handle specific events such as load current inrush or a start-up sequence and to guarantee optimal transient responses, additional functions are included into each local controllers. The inter-cell communication protocol is described, along with necessary design considerations of threshold and timing values. Finally, functional simulations are carried out on a 5-leg 12V/1.2V 60W multiphase converter, which validate the proposed decentralized phase-shedding strategy for a microcontroller power supply implementation.

This paper proposes an approach to estimate the parameters of an AC-DC boost power factor corrector converter which includes an EMI filter. To this end, once the topology is known, measurements at the input and output terminals of the converter are done to identify the values of the passive elements. The proposed methodology is based on the trust-region nonlinear least squares algorithm to identify the parameters of the converter. The steady-state and the transient signals of the converter at the input/output terminals are acquired non-intrusively without any internal modification of the circuitry. The accuracy of the parameter identification carried out is determined by comparing the estimated values with the actual values provided by the manufacturer, and by contrasting the measured signals with the ones obtained with a simulation model with the estimated values of the parameters. The results presented in this paper prove the accuracy of the proposed approach, which can be extended to other power converters and filters.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

This paper investigates the efficacy of YOLOv8 variants for vehicle detection and license plate detection within smart parking applications, emphasizing performance under varying ambient lighting conditions. The proposed system is to seize full video frames, extracts regions of interest containing vehicles, and feeds them into separate, pre-trained YOLOv8 models – one dedicated to vehicle detection and another for license plate detection. Four YOLOv8 variants, nano, small, medium, and large, are evaluated. As a pre-processing step, the images are processed with the help of OpenCV and Pillow libraries to adjust the luminosity and increase the images’ DPI so that they would be easy to perceive by the Tesseract OCR engine. Sixteen potential combinations arise from pairing the four YOLOv8 models for vehicle and license plate detection tasks. To identify the most suitable combinations, we employ the Multi-Criteria Decision-Making method, specifically Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) analysis. This analysis considers 4 critical metrics: Precision, mean average precision at 95% Intersection of Union threshold, Recall and Total Inference Time. The objective is to achieve an optimal balance between high accuracy and real-time processing. Following the selection of optimal YOLOv8 combinations through TOPSIS analysis, we assess their performance under varying ambient light intensity (measured in lux). This evaluation aims to identify the most robust model combinations that ensure accurate vehicle and license plate recognition across the diverse lighting conditions encountered in real-world environment.

To reduce the redundant counting of TDC in high-speed applications and thus reduce power consumption, a TDC architecture is proposed to quantify the difference between two adjacent rows of pixel signals. This structure can remove the identical part between two rows of pixel signals by adjusting the start and stop signal of the TDC, which will reduce the number of flipping of D flip-flops in the TDC. In the 110nm CMOS process, simulation results show that this design achieves an effective number of bits (ENOB) of 4.72 bits and a Figure of Merit (FoM) of 104.7 fJ/step - 162.3 fJ/step with a power consumption ranging from 60 µW to 93 µW. Compared with traditional counting methods, the proposed TDC can reduce counting power consumption by 30%.

Multipactor is a common discharge phenomenon occurred in space microwave systems. The surface microstructure has been verified to be effective to mitigate multipactor. In this work, we design a square coaxial low-pass filter (SCLPF) with dielectric sheets loaded to check the multipactor dependence on the structure parameters of the loaded dielectric sheets, and further model groove structures on the sensitive area surface to lower the risk of multipactor. Simulation results indicate that the SCLPF loaded with alumina and PTFE exhibits good operational characteristics, and the multipactor threshold is significantly improved after introducing the surface grooves. Then we investigate the effects of three typical groove parameters, groove depth, groove number, and aspect ratio, on the multipactor threshold of the SCLPF device. The results show that the multipactor threshold raise at first as the groove number and groove depth increase, and then the threshold reaches a saturation status. For a deeper analysis of multipactor, we discuss how the grooves shelter the secondary electrons, and further mitigate the electron avalanche. Furthermore, the mechanisms of threshold saturation under the effect of groove parameters are analyzed in detail, and a contour map for the multipactor threshold of PTFE-loaded SCLPFs is given, which makes significant sense for predicting the multipactor threshold of the devices with its sensitive surface being grooved. The regularity of modulating the multipactor threshold by the groove structures obtained in this study is of engineering significance for suppressing multipactor in microwave devices in practical applications.

The paper investigates the performance of a full analog self-jammer canceller able to operate in UHF RFID devices. The scheme has been realized using only SMT devices avoiding custom designed components. The paper analyzes the theoretical performance and experimental validation using a modular microwave technology approach.

The Imbalance Cost Pass-Through (ICPT) is a flexible component of the Incentive Regulation (IBR) that empowers power producers to adjust tariffs in response to variable fuel prices, thereby enhancing the economic resilience of electricity generation. However, the cost of electricity generation is significantly influenced by the volatility of commodity prices, including coal, gas and LNG. In Malaysia, the Energy Commission has conducted biannual reviews of fuel and other generation costs. Any cost savings or increases identified during these reviews will be passed on to customers in the form of rebates or surcharges. Due to that reason, this study proposes ICPT price forecasting for the electricity market in Peninsular Malaysia. The study aims to construct an ICPT-related baseline model for the peninsular generation data by employing three forecasting methods. The forecasting performance is analysed by a Mean Absolute Percentage Error (MAPE). In findings, the ARIMA method is one of the most accurate forecasting methods for fuel prices compared to the Moving Average (MA) and LSSVM methods. The observed price differences between the ARIMA and LSSVM models for ICPT are minimal. The ICPT price for July-December 2022 and January-June 2023 is MYR 0.21/ kWh for ARIMA and MYR 0.18/kWh for LSSVM, which are close to the actual TNB’s ICPT tariff. As for the forecasting, the ICPT price is expected to drop for the next announcement. The findings of this study may contribute to a positive impact on the sustainability of the energy sector in Malaysia.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Dried blood spot (DBS) testing on confetti is one of the most common methods used to collect and extract DNA from field samples for molecular epidemiology of malaria studies. Here, we investigated whether ethanol or other solutions used to clean scissors are a source of sample contamination. DBS were prepared from 3 drops of blood from two Plasmodium falciparum cultures spotted on confetti, and 3 solutions (water, ethanol and DNase) were used to clean scissors between spots during DNA extraction. For each cleaning solution, two blank confetti were used as negative controls. Samples were analyzed by PCR-based genotyping of merozoite surface proteins 1 & 2 (msp-1 and msp-2), and P. falciparum chloroquine resistance transporter (Pfcrt). A total of 15 samples were analyzed. Based on msp-1 and msp-2 amplification, P. falciparum was detected on blank confetti when scissors were washed with ethanol. Based on Pfcrt amplification, DNA of P. falciparum was detected on blank confetti when scissors were cleaned with ethanol or water. No P. falciparum genes were detected on blank confetti when scissors were cleaned with DNase. Scissors cleaned with DNase prevented cross-contamination between samples during processing of dried blood spots, whereas ethanol (which is commonly used) fails to avert cross-contamination.

The search of DNA polymorphisms useful for the genetic improvement of dairy farm animals lasts more than 40 years with relevant findings in cattle for milk traits, where the best combination of alleles for dairy processing have been found in casein genes and in the DGAT1. Nowadays, similar results are not reached yet in river buffaloes despite advanced genomic technologies and accurate phenotype records are available. The aim of the present study was to investigate and validate in a larger buffalo population the effect on six milk traits of four single nucleotide polymorphisms (SNP) in the CSN1S1, CSN3, SCD and LPL genes, previously reported to be associated with or affect dairy traits in smaller populations often belonging to one farm. A total of 800 buffaloes were genotyped. Daily milk yield (dMY, kg), protein yield (dPY, kg) and fat yields (dFY, kg), fat and protein contents (dFP, % and dPP, %), somatic cell count (SCC, 103cell/ml) and urea (mg/dl) were individually recorded in each month for the whole lactation from 2010 to 2021. A total of 15,742 individual milk test day records (2,496 lactations) were available on 680 buffalo cows with 3.6±1.7 parity (from 1 to 13) and 6.1±1.2 test day records per lactation on average. Three out four SNP in CSN1S1, CSN3 and LPL were associated with at least one of analyzed traits. In particular, the CSN1S1 (AJ005430:c.578C>T) gave favorable associations with all yield traits (dMY, p=0.022; dPY, p=0.014 ; dFY, p=0.029) and SCS (p=0.032), whereas the CSN3 (HQ677596: c.536C>T) positively associated with SCS (p=0.005) and milk urea (p=0.04). Favorable effect on dMY (p=0.028), dFP (p=0.027) and dPP (p=0.050) were observed for the LPL. Conversely, SCD did not show any association with milk traits. This is the first example of confirmation study carried out in the Mediterranean river buffalo for genes of economic interest in dairy field and it represents a very important indication for the preselection of young bulls destined to breeding programs in the view of a more sustainable dairy production.

This paper will discuss Data, Information, Knowledge, and Wisdom, which is commonly referred to as DIKW. The DIKW Pyramid Model that is often referenced in both academics and practitioner circles will be discussed and shown to be faulty on several levels, including. a lack of definitional agreement. A new DIKW framework will be proposed that focuses on what the DIKW elements do in the way humans think, not what they are by definition. Information as a replacement for wasted physical resources in goal-oriented tasks will be a central organizing point. The paper will move the DIKW discussion to the computer-based concept of Digital Twins (DTs) and its augmentation of how we can use DIKW to be more effective and efficient. This will especially be the case as we move to Intelligent Digital Twins (IDT) with Artificial Intelligence (AI).

The realization of a perfect absorber A = 1 with transmittance and reflectance T=R=0 by a thin metasurface is one of the hot topics in recent nanophotonics prompted by energy harvesting and sensor applications (A + R + T =1 is the energy conservation). Here we tested optical properties of over 400 structures of metal-insulator-metal (MIM) metasurfaces for a range of variation in thickness of insulator, the diameter of a disc and intra-disc distance experimentally and numerically. Conditions of a near-perfect absorption A > 95% with simultaneously occurring anti-reflection property (R < 5%) were experimentally determined. Differences between the bulk vs. nano-thin film properties at mid-IR of the used materials can be of interest for plasmonic multi-metal alloys and high entropy metals.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

Healthcare crises occur occasionally are very disruptive and resource consuming. The Covid-19 pandemic provided an example of inefficient wasteful resource management that would be unsustainable in the long term. This paper presents a framework for sustainable crisis management that will be applicable for future crises. The methodology is also applicable to other pandemics, wars, multi-casualty natural disasters, industrial disasters, etc. Attention focuses on rapid crisis resolution such as lockdowns. Despite unprecedented investments in healthcare, lack of capacity and timeliness are still problems affecting every country, even the wealthier ones. During the Covid19 pandemic, some healthcare systems around the world have collapsed. For example, Brazil, Spain, Italy, and more. This is due to the lack of a clear methodology for handling such crises. This paper presents a resource-based methodology to cope with healthcare crises considering three scenarios: “Peace”, “War” and “Tsunami”. The paper outlines a methodology for identifying the system bottlenecks for coping with the crisis in each scenario by using established simple tools. These tools assure significant resource frugality that will enhance sustainability. The paper also analyses where the system constraint should be and prescribes how to prepare for such scenarios. A large medical center case study demonstrates our approach. During “peace” times, evolutionary strategies should be used exclusively. During “war” times, a hybrid – evolutionary/disruptive (revolutionary) strategy. During the “Tsunami” scenario, one should rely only on the disruptive (revolutionary) strategy. This methodology can be extended to other scenarios and other lines of research.

In this paper the one-to-one correspondences and equivalences between ideals, primals, filters and grills are introduced. It is shown the local functions and the topological spaces induced by them are the same. From this point of view, the topological properties with respect to one topology can be derived from topological properties valid in the corresponding topology.

Face detection is an important problem in computer vision because it enables a wide range of applications, such as facial recognition and analysis of human behavior. The problem is challenging because of the large variations in facial appearance across different individuals and different lighting and pose conditions. One way to detect faces is to utilize a highly advanced face detection method, such as RetinaFace, which uses deep learning techniques to achieve high accuracy in various datasets. However, even the best face detectors can produce false positives, which can lead to incorrect or unreliable results. In this paper, we propose a method for reducing false positives in face detection by using information from a depth map. A depth map is a two-dimensional representation of the distance of objects in an image from the camera. By using the depth information, the proposed method is able to better differentiate between true faces and false positives. The authors evaluate their method on a combined dataset of 549 images, containing a total of 614 upright frontal faces. The results show that the proposed method is able to significantly reduce the number of false positives without sacrificing the overall detection rate. This indicates that the use of depth information can be a useful tool for improving face detection performance.

The mineralogical indices, e.g., Quartz Index (QI), Carbonate Index (CI), Mafic Index (MI) for ASTER multispectral thermal infrared (TIR) data have been applied to various geological materials. The indices are proved to be robust in extracting geological information at the local scale. Considering the relatively narrow spatial coverage of each ASTER scene compared to LANDSAT, many scenes are needed when mosaicking the images to be mapped at regional scales. We develop a system to search ASTER data for a target area given the vast and expanding ASTER data archive. The data is then conditioned, prioritized, and the indices are calculated before finally mosaicking the imagery. The maps of the indices covering the very wide region of the central Tibetan Plateau are produced with this system. The characteristic features of the indices relating to their geology in the study area are analyzed and discussed. Many interesting lithological and structural information that are not currently well understood in the central Tibetan Plateau, the highest and most extensive plateau in the world, with an average elevation of over 4,500 meters above sea level, for example, distributions of the mafic-ultramafic rocks along the suture zones, the quarzitic and marine sedimentology accreted to the Eurasian continent and sulfate layers related to the Tethys and neo-Tethys geological setting can be retrieved from the processed ASTER images.

The stepwise hydrogenation of the C=C bond and C=O group of acrolein on Au₃ and Au₅ model systems is investigated using the density functional theory(DFT) PW91 functional. Our results show that the C=C hydrogenation is more favorable than that of C=O bond on Au₃ with the barriers of the rate-determining step being 0.35 and 0.62 eV respectively. On the other hand, the C=O reduction is preferred over the hydrogenation of the C=C bond on Au₅. The corresponding barriers of the rate-determining steps are 0.45 and 0.54 eV, respectively. This demonstrated that the second hydrogenation step controls the reaction on both Au₃ and Au₅ for C=O and C=C hydrogenation and the C=O hydrogenation on Au₅ is preferred over the hydrogenation of the C=C bond, which is helpful to address the reactivity of small size-selected supported gold clusters.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Antibacterial bone cements (ABCs), such as antibiotic-loaded bone cements (ALBCs), have been widely utilized in clinical treatments. Currently, bone cements loaded with vancomycin, gentamicin, tobramycin, or clindamycin are approved by the US Food and Drug Administration. However, traditional ALBCs exhibit drawbacks like burst release and bacterial resistance. Therefore, there is a demand for the development of antibacterial bone cements containing novel agents. In this review, we summarize the latest advancements in ABCs. More importantly, we provide an overview and outlook on novel antibacterial agent-loaded bone cements, including metallic antibacterial agents, pH-switchable antibacterial agents, cationic polymers, N-halamines, non-leaching acrylic monomers, antimicrobial peptides, etc. Offering novel perspectives for designing ABCs and treating bone infections.

An eigenvalue equation representing symmetric (dual) quantum equation is introduced. The particle is described by two scalar wavefunctions, and two vector wavefunctions. The eigenfunction is found to satisfy the quantum Telegraph equation keeping the form of the particle fixed but decaying its amplitude. An analogy with Maxwellian equations is presented. Massive electromagnetic field will satisfy a quantum Telegraph equation instead of a pure wave equation. This equation resembles the motion of the electromagnetic field in a conducting medium. With a particular setting of the scalar and vector wavefunctions, the dual quantum equations are found to yield the quantized Maxwell's equations. The total energy of the particle is related to the phase velocity ($v_p$) of the wave representing it by $E=p\,|v_p|$, where $p$ is the matter wave momentum. A particular solution which describes the process under which the particle undergoes a creation and annihilation is derived. The force acting on the moving particle is expressed in a dual Lorentz-like form. If the particle moves like a fluid, a dissipative (drag) quantum force will arise.

The described data set contains features from the machine control of a five-axis milling machine. The features were recorded during thirteen series productions. Each series production includes a changeover process in which the machine was set up for the production of a different product. In addition to the timestamps and the twenty recorded features derived from Numerical Control (NC) control variables, the data set also contains labels for the different production phases. For this purpose, up to 23 phases were assigned, which are based on a generalized milling process. The data set consists of thirteen .csv files, each representing a series production. The data set was recorded in a production company in the contract manufacturing sector for components with real series orders in ongoing industrial production.

Several recent studies have indicated that miR-30a plays critical roles in various biological processes and diseases. However, the mechanism of miR-30a participation in the regulation of idiopathic pulmonary fibrosis (IPF) is ambiguous. Our previous study demonstrated that miR-30a may function as a novel therapeutic target for lung fibrosis by blocking mitochondrial fission, which is dependent on dynamin-related protein-1 (Drp-1). However, the regulatory mechanism between miR-30a and Drp-1 has yet to be investigated. In addition, whether miR-30a can act as a potential therapeutic has not been verified in vivo. In this study, the miR-30a expression in IPF patients was evaluated. Computational analysis and a dual luciferase reporter system assay were used to identify the target gene of miR-30a, and cell transfection was used to confirm this relationship. Ten-eleven translocation 1 (TET1) was validated as a direct target of miR-30a, and the transfection of miR-30a mimic/inhibitor significantly reduced/increased the expression of TET1 protein. Further experiment verified that the interference on TET1(siRNA) could inhibit the hydroxymethlation of the Drp-1 promoter. Finally, miR-30a agomir was designed and applied to identify and validate the therapeutic effect of miR-30a in vivo. Our study demonstrated that miR-30a could inhibit the TET1 expression by base pairing with complementary sites in the 3′ untranslated region to regulate the hydroxymethlation of the Drp-1 promoter. Furthermore, miR-30a could act as a potential therapeutic target for IPF.

High-precision ground point cloud data has a wide range of applications in various fields, and the separation of ground points from non-ground points is a crucial preprocessing step. Therefore, designing an efficient, accurate, and stable ground extraction algorithm is of great significance for improving the processing efficiency and analysis accuracy of point cloud data. The study area in this article was a Park in Guilin, Guangxi, China. The point cloud was obtained by utilizing the UAV platform. In order to improve the stability and accuracy of the Filter algorithm, this article proposed a triangular grid filter based on Slope Filter, found violation points by the spatial position relationship within each point in the triangulation network, improved KD-Tree-Based Euclidean Clustering, and applied it to the non-ground points extraction, this method has good accuracy, stability and achieves good results in separating ground points from non-ground points. At first, using Slope Filter to remove some non-ground points, to reduce the error of taking ground points as non-ground points; Secondly, established a triangular grid based on the triangular relationship between each point, the violation-triangle can determin through the grid, and then the corresponding violation points were found in the violation-triangle; Thirdly, according to the three-point collinear method to extract the regular points, used these points to extract the regular landmarks by KD-Tree-Based Euclidean Clustering and Convex Hull Algorithm; Finally, removed disperse points and irregular landmarks by Clustering Algorithm. In order to confirm the superiority of this algorithm, this article compared the filter effects of various algorithms on the study area and filtered the 15 sample data provided by ISPRS, and obtained an average error of 3. 46%. The results showed that the algorithm in this article have a high processing efficiency and accuracy, which can greatly improve the processing efficiency of point cloud data in practical applications.

Loose Tangle is a concept in graph theory that has a dual relationship with branch-width which is well-known graph width parameter. Ultrafilter, a fundamental notion in mathematics, is similarly known to have a dual relationship with branch-width when extended to a connectivity system (X, f). In this compact paper, we revisit and contemplate the interplay between Loose Tangle and Filter through the lens of a submodular partition function.

The paper presents the design stages of a single-phase Silicon Carbide bidirectional DC-AC converter. This includes the LCL filter design responsible to meet grid connection requirements. A 3kW laboratory prototype of the power converter is built employing a low-cost phase locked loop and its results are presented. The design of the low-cost phase locked loop and its implementation are depicted in some detail.

Aiming to improve medical diagnosis and treatment, artificial intelligence (AI) has emerged as a transformational force in the healthcare industry. In this article, we examine how AI is increasingly being used to improve healthcare, with an emphasis on how it is changing medical diagnosis and treatment. We explore the opportunities, threats, and ethical concerns of incorporating AI into healthcare practice. In addition, we feature important AI applications in radiology, pathology, cardiology, and cancer. AI has great potential to improve patient outcomes, diagnostic accuracy, and the ability to provide individualized treatment plans in the future if it is used and refined with care.

Abstract: Efforts for carbon emission reduction have been identified as a major climate change mitigation target in the Paris Agreement. The 26th Conference of Parties to the United Nations Framework Convention on Climate Change highlighted the worldwide effort for cleaner and greener mining, urging the mineral industry to embrace greener operational emissions reduction technologies and strategies. Ghana pledged at the Paris Conference to reduce CO2 emissions by 15% and increase renewable energy share to 10% of the national energy mix. Here the fundamental question is how Ghana’s mining industry can contribute to CO2 emission reduction efforts. This paper investigates barriers to low-carbon emission policy implementation among mining companies in Ghana. The questionnaire survey was conducted among Ghana’s four large-scale gold mining companies. As the sample number of available companies is limited, we used a descriptive analysis to assess the responses. The results show that the companies expressed widely different ways to respond to the issues of cost, a government policy/regulations for carbon emission reduction, and the adoption/acquisition of low-carbon technologies. Those companies that are relatively less prepared for this endeavor emphasized the uncertainties of securing sufficient energy in case of using low-carbon technologies. They also expressed a need for more trained workers to handle low-carbon technologies. All companies agreed with a expected high cost of adopting low-carbon options. There was a communication gap with the relevant government ministry about low-carbon mining options where the government should be able to facilitate the involvement of othe low technology providers, such as solar PV installation.

Biochar is a carbonaceous material derived from the thermochemical conversion of biomass under oxygen-lean conditions. Its properties render it many applications in agriculture, environmental remediation, and catalysis. Commonly produced by pyrolysis under a nitrogen atmosphere, the biochar composition is influenced mainly by residence time, heating rate, and process temperature. The existing literature primarily assesses biochar properties, such as ultimate, proximate, calorific, porosity, and combustibility, generated under various thermo-conversion conditions. However, there is a notable lack of sufficient investigation and attention given to the practical application of biochar. This article seeks to bridge that gap by enhancing the comprehension of the necessary experimental assessment for specific biochar applications and proposing process optimization methods using Multi-Criteria Decision Analysis (MCDA). By delving into these aspects, the study offers a concise overview of biochar production and presents a comprehensive panorama based on articles and patents. Additionally, the research explores the physicochemical characterization techniques associated with biochar and its various applications in conjunction with MCDA. This comprehensive approach aims to uncover valuable insights that could further advance the practical and sustainable utilization of biochar in a wide range of fields.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

Obesity is associated with serious comorbidities and economic implications. Bariatric surgery, most commonly Roux-en-Y gastric bypass and sleeve gastrectomy, are effective options for weight loss and improvement of obesity-related comorbidities. With the growing obesity epidemic, there has been a concomitant rise in bariatric surgeries, particularly in sleeve gastrectomy, which has been the most widely performed bariatric surgery since 2013. Gastroesophageal reflux disease (GERD) is highly prevalent in obese individuals, can significantly impact quality of life and may lead to serious complications. Obesity and GERD both improve with weight loss. However, as the incidence of sleeve gastrectomy rises, recent data has revealed a risk of exacerbation of pre-existing GERD or the development of de novo GERD following sleeve gastrectomy. We performed a detailed review of GERD post-sleeve gastrectomy, including its overall incidence, pathophysiology and current treatment paradigms.

The construction industry is a resource and energy intensive industry and thus, has been criti-cized due to rising environmental concerns. As a result of that it has gained heightened interest in the concept of Circular Economy (CE) over the last decade to its ability to promote the slowing, reducing, and closing production and consumption cycles of materials and products used in the construction practices. Digital technologies hold potential to enhance the construction industry's ability to integrate the concept of CE in its practices. However, a clear understanding of digital technology (DT) related barriers that hinder practical implementation of CE, appears to be lacking within the sector. In light of this, this study aims to identify the barriers to adopting DTs to im-plement CE practices in the construction industry. To achieve this aim, a systematic literature review was conducted by reviewing twenty-three (23) relevant papers published until January 2024 in Scopus database. The VOS viewer software was used to perform a co-occurrence analysis of keywords to identify new and popular study areas in the field and content analysis was used to analyse the major barriers to adapt DTs to implement CE in the construction industry. The study identified thirty-four (34) barriers to use DTs to implement CE and these were categorized into nine areas such as: infrastructure, organizational, regulatory, standardization, investment, nature of the construction industry, technological, stakeholder and data related barriers. These findings will be beneficial for construction practitioners and policy makers to adopt DTs to integrate CE practices in the construction industry.

This paper explores Ghana's two-decade journey in developing a digital land information system (LIS), exemplified by Ghana Enterprise Land Information System (GELIS) and Enterprise Land Information System (ELIS). Despite advancements by Ghana’s Lands Commission, manual processes persist and coexist with digital ones. Our study uses a qualitative approach to assess the effectiveness of the LIS implemented in Accra. The study found that Accra’s LIS is highly aligned with clear institutional mandates, roles, and responsibilities as well as the availability of laws and policies to support analogue to digital conversion. Furthermore, a robust approach for protecting data, operating system and software underpins the system. Subsequently, the integration of a digital LIS has enhanced service delivery and accountability. Nonetheless, Accra’s LIS is still at the beginning of a comprehensive learning and development curve. To sustain the LIS requires furtherance in the implementation plan, funding, law implementation, ICT strategy, divisional integration, work processes, data quality, and communication strategy. These findings will inform the next steps of improvement for Accra's LIS and guide its nationwide scaling, contributing to discussions on technology acceptance dynamics in predominantly analogue environments.

The purpose of this study is to establish whether digital literacy and insurtech adoption influence insurance inclusion in Uganda. Principally, we sought to determine whether insurtech adoption mediates the nexus between digital literacy and insurance inclusion. This study adopted a cross-sectional and quantitative correlational approach. The study’s sample was 391 individuals who had used digital platforms such as mobile phones and computers to access insurance products and services in Uganda. Data were collected using structured survey questionnaires. Partial Least Squares Structural Equation Modelling (PLSEM) was employed to test the hypothesised relationships. The results demonstrate that both digital literacy and insurtech adoption significantly and positively influence insurance inclusion. We also found digital literacy to be a significant and positive determinant of insurtech adoption. Markedly, it was found that insurtech adoption mediates the association between digital literacy and insurance inclusion in Uganda. However, this study was conducted in a developing country with an underdeveloped insurance market and with low technological advancement. This may affect generalisation of the study findings. This study’s novelty lies in establishing how digital literacy and insurtech adoption interplay to influence insurance inclusion in Uganda. This is the first study to examine the effect of digital literacy and insurtech adoption on insurance inclusion.

Preschoolers with disabilities and their caregivers have been neglected in health and social service provision in most low-income countries and arguably too in low resourced areas of more affluent nations. Yet as this rapid review of published literature identifies, there are low-cost, evidence-based strategies to address their needs that can be implemented in communities by local people. Five key features of the necessary supports are examined. First the leadership functions required to create and implement the support services. Second, the family-centred, home-based support provided to caregivers and the personnel undertaking this form of support. Third, providing opportunities for peer support to flourish and encouraging the formation of advocacy groups across families. Fourth, mobilizing the support of significant groups within the community; notably traditional healers and leaders; health services and poverty alleviation initiatives. Fifth, devising ways in which preschool educational opportunities can be offered to children as a prelude to their inclusion in primary schools. The review serves a further purpose. It provides an example of how public health researchers and academics could achieve more rapid implementation of evidence-based knowledge into existing and new support services through dissemination to community practitioners.

The conventional well placement was done manually by using a numerical reservoir simulator, and it required a lengthy trial-and-error process. It required great experience and expertise to manipulate the variables and uncertainties that lie on the reservoir to determine the best placement of the well. In addition, the traditional gradient-based methods such as Line-search and Trust-region were not viable in terms of maximum results obtained. Gradient-based methods were too dependent on the surface gradient of the solution and may only converge to local optima instead of global optima. Complex reservoirs have rough surfaces with high uncertainties, which hinders the traditional gradient-based method from converging to global optima. Thus, genetic algorithms were utilized to automate the manual trial-and-error process and to overcome the limitations of the traditional gradient-based method. The objectives of this study were to analyse the effect of different initial well placement distributions, the number of random solution sizes, and the crossover rate on cumulative oil production. A synthetic reservoir model built using CMG Builder was used as the testing platform for the optimization problems. Well-placement parameterization and optimization set-up were carried out using the CMG CMOST optimization tool. The integration of CMG IMEX and CMOST optimized cumulative oil production based on the objectives of the study. The results obtained showed that the higher number of random solutions used resulted in higher cumulative oil production, with more generations needed to reach the optimum solution. It can be concluded that the larger number of random solutions used increased the probability of reaching the optimum solution, but will take more generations.

Rheumatoid arthritis (RA) is an autoimmune disease in which joints are gradually de-stroyed, and early diagnosis and treatment before joint deformation or destruction is im-portant. The detection of novel RA biomarkers in saliva may facilitate the early detection of RA before the onset of disease. In this study, we conducted a comprehensive proteomic analysis of salivary proteins from RA model mice. Proteins were identified by Western blotting and enzyme-linked immunosorbent assay in serum, saliva, and ankle joints from DBA/1JJmsSlc mice, a model of rheumatoid arthritis. Ankle joints and submandibular glands were hematoxylin and eosin stained and immunostained, and the results were compared with those of control mice. Citrullinated α1 antitrypsin (A1AT, 46 kDa) was commonly detected in saliva, serum, and ankle joints of severe RA model mice, and was confirmed by proteome analysis. Western blotting detected a band corresponding to 46 kDa in serum, saliva and ankle joints, and immunostaining of ankle joints with A1AT an-tibody showed a strong positive signal in the synovium. In DBA/1JJmsSlc mice, not only cyclic citrullinated peptide antibodies but also A1AT may be involved in protein citrulli-nation and contribute to the development and severity of RA.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Background: Patients with allergic rhinitis (AR) have bothersome symptoms that may assess using the visual analog scale (VAS). Asthma frequently is associated with AR. The present study investigated the role of VAS in children with newly-diagnosed AR. Methods: Parameters were VAS for nasal and asthma symptoms, and doctor’s perception of these diseases, medication use, and asthma comorbidity. Results: 67% of AR children had asthma. Severity of perceived nasal symptoms was associated with more intense asthma symptoms and doctor’s perception of disease severity (p<0.001 and p=0.02, re-spectively. Conclusions: Allergic rhinitis frequently is associated with asthma in child-hood. Symptom perception assessment using VAS is a simple tool for assessing their intensity. Moreover, the severity of nasal symptoms is associated with asthma symptom severity. Therefore, asthma should be carefully considered in AR children and require appropriate symptom perception assessment.

In this comprehensive review, we delve into the realm of intention recognition within the context of digital forensics and cybercrime. The rise of cybercrime has become a major concern for individuals, organizations, and governments worldwide. Digital forensics is a field that deals with the investigation and analysis of digital evidence in order to identify, preserve, and analyze information that can be used as evidence in a court of law. Whereas, Intention recognition is a subfield of artificial intelligence that deals with the identification of agents’ intentions based on their actions and change of states. In the context of cybercrime, intention recognition can be used to identify the intentions of cybercriminals and even to predict their future actions. Employing a meticulous six-step systematic review approach, we curated research articles from reputable journals and categorized them into three distinct modeling approaches: logic-based, classical machine learning-based, and deep learning-based. Notably, intention recognition has transcended its historical confinement to network security, now addressing critical challenges across various subdomains, including social engineering attacks, AI black box vulnerabilities, and physical security. While deep learning emerges as the dominant paradigm, its inherent lack of transparency poses unique challenges in the digital forensics landscape. We advocate for hybrid solutions that blend deep learning’s power with interpretability. Furthermore, we propose the creation of a comprehensive taxonomy to precisely define intention recognition, paving the way for future advancements in this pivotal field.

(1) Background: The aim of this study was to investigate the circadian rhythms of tongue features according to the effects of physiological phases over a 24-hour period. (2) Methods: Fifteen healthy participants aged 20 to 69 years were recruited. The participants did not have current chronic diseases or past diseases and had to meet the inclusion and exclusion criteria. The participants stayed at the Gil Hospital for a duration of 2 nights and 3 days. On the first day, at 18:00, they consumed their allocated portions of food and water and then completed a questionnaire. At approximately 21:00, their tongue images were acquired using a computerized tongue image acquisition system, following which they slept for 8 hours, commencing at 23:00. Measurements were taken from 07:00 through 21:00 on the second day, and the final acquisition was taken at 07:00 on the following morning, resulting in a total of eight images. The circadian rhythm was authenticated and quantified utilizing the single cosinor analysis, a technique for periodic regression analysis for fitting a 24-hour cosine curve. (3) Results: Cosinor analysis revealed that all tongue features were significantly related to circadian rhythm. (4) Conclusions: The results of this study may be important for considering the time of day at which the tongue is observed and tongue status is evaluated.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

Diabetic foot ulcers (DFUs) significantly affect the lives of patients and increase the risk of hospital stay and amputation. We suggest a remote-monitoring platform for better DFU care. This system uses digital health metrics (scaled from 0 to 10, where higher scores indicate a greater risk of slow healing) to provide a comprehensive overview through a visual interface. The platform features smart offloading devices that capture behavioral metrics such as offloading adherence, daily steps, and cadence. Coupled with remotely measurable frailty and phenotypic metrics, it offers an in-depth patient profile. Additional demographic data, wound characteristics, and clinical parameters, such as cognitive function, were integrated, contributing to a comprehensive risk factor profile. We evaluated the feasibility of this platform with 124 DFU patients over 12 weeks; 39% experienced unfavorable outcomes such as dropout, adverse events, or non-healing. Digital biomarkers were benchmarked (0-10), categorized into low, medium, and high risk for unfavorable outcomes, and visually represented using color-coded radar plots. The initial results of case reports illustrate the value of this holistic visualization to pinpoint the underlying risk factors for unfavorable outcomes, including a high number of steps, poor adherence, and cognitive impairment. Although future studies are needed to validate the effectiveness of this visualization in personalizing care and improving wound outcomes, early results in identifying risk factors for unfavorable outcomes are promising.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

This paper examines the asymmetrical relationship between exchange rate and consumer prices in 40 Sub-Saharan African (SSA) countries from 1990q1 to 2017q4. The exchange rate pass-through (ERPT) to consumer prices is estimated for each country by using the nonlinear autoregressive distributed lags (NARDL) framework and dynamic panel estimators robust to cross-sectionally correlated errors. Firstly, our findings suggest an asymmetrical ERPT in the SSA region during the short-term, whereas there are mixed results across sub-regions in the long-term. Next, we find incomplete and significant ERPT to consumer prices in the entire SSA region which is higher during the depreciation of the local currency than after appreciations. Third, we find nonlinear ERPT with respect to the size of the exchange rate. The pass-through is higher during large exchange rate changes than after small changes. Finally, we find that the pass-through is greater in the countries with fixed exchange rate regime (CFA franc zone) having low inflationary environment than in the other SSA countries with flexible exchange rate regime and high inflation levels. As a result, policymakers should take into account these asymmetries and non-linearities to improve the credibility of monetary policy, strengthen trade liberalization and establish competitive market structures in the Sub-Saharan region.

This paper introduces a structured design for an effective power-sharing technique among converter-interfaced distributed generation (DG) units within a microgrid that operates without a synchronous generator. The proposed power-sharing technique leverages the battery energy storage system (BESS) to promptly respond to network changes. The real power output of each commercial distributed energy resources (CDER) unit is governed by a frequency-droop characteristic and a complementary frequency restoration strategy. Deloading techniques are employed by solar and wind power generators to enhance response during power supply or demand disturbances. To ensure microgrid stability, small-signal analysis is conducted for controller design, including the determination of stability margins. Initial tuning of the power-sharing technique parameters is achieved using the Ziegler-Nichols Method, followed by further optimization through a meta-heuristical algorithm to enhance the response time of energy sources. The proposed power-sharing technique's performance is evaluated on a benchmark medium voltage network using industry-standard commercial software. The test results demonstrate the precise and rapid power-sharing capabilities among DGs facilitated by the proposed technique, highlighting its effectiveness in dynamic microgrid environments.

In the context of cognitive radio, smart city and Internet-of-Things, the need of advanced radio spectrum monitoring becomes crucial. However, surveillance of a wide frequency band without using extremely expensive high sampling rates devices is a challenging task. The recent development of compressed sampling approaches offers a promising solution to these problems. In this context, the Modulated Wideband Converter (MWC), a blind sub-Nyquist sampling system, is probably the most realistic approach and was successfully validated in real-world conditions. The MWC can be realized with existing analog components and there exist calibration methods which are able to integrate the imperfections of the mixers, filters and ADCs, hence allowing its use in real-world. The MWC underlying model is based on signal processing concepts such as filtering, modulation, Fourier series decomposition, oversampling and undersampling, spectrum aliasing, and so on, as well as in-flow data processing. In this paper we develop an MWC model which is entirely based on linear algebra, matrix theory and block processing. We show that this approach has many interests: straightforward translation of mathematical equations into simple and efficient software programming, suppression of some constraints of the initial model, and providing a basis for the development of an extremely fast system calibration method. With a typical MWC acquisition device we obtained a speed up of a factor greater than 20 of the calibration computation time, compared with a previous implementation.

Respiratory syncytial virus (RSV) infection is a major cause of severe respiratory disease in infants and young children worldwide. Two vaccines targeting the elderly and pregnant women have been recently approved employing the prefusion form of the RSV-fusion protein (F). However, there are currently no vaccines for infants. Studies have shown a fusion-inactive prefusogenic F form is significantly more immunogenic and produces higher antibody titers to both the prefusion and postfusion structures of the F protein. Here we have developed RSV virus-like particles (RSV-VLPs) consisting of prefusogenic F, RSV glycoprotein and matrix proteins, produced them using the baculovirus expression system, and studied their protective efficacy in Balb/c mice. Morphology and successful assembly of VLPs were confirmed by transmission electron microscopy and western blot. Mice immunized with VLPs developed high levels of serum IgG and neutralizing antibodies as compared with mice immunized with inactivated virus. The VLP vaccine also induced higher levels of IFNγ and IL4, elicited limited proliferation of CD4+ and CD8+ T cells but higher cytotoxic-T-lymphocyte responses. VLP immunization abolished lung pathology in the mice after RSV challenge. Overall, our results indicate that RSV-VLPs consisting of prefusogenic F, glycoprotein and matrix proteins are a potential vaccine candidate against RSV.

This study examines the activities conducted at the archaeological site of Aptera in Crete, Greece. The research was part of the DIACHRONIC LANDSCAPES International Design Workshop, organized by the CAM (Center for Mediterranean Architecture), TUC (Technological University of Crete School of Architecture), and UNIFE (University of Ferrara Department of Architecture). This article outlines the methods used for data acquisition and processing on a territorial scale, which generated digital outputs necessary for the analysis and design phases of the workshop, as well as for further examination of the results. The collected data, obtained through low-cost aerial photogrammetric surveying and GNSS terrestrial coordinate detection, were integrated in a Structure from Motion workflow that led to the creation and exportation of various digital outputs, such as point clouds, DTM, DSM, orthophotos, and contour lines. An accuracy analysis was performed to evaluate the effectiveness and efficiency of the digital models compared to the implemented surveying strategies, including the Ground Control Point and Quality Check Point marker positioning strategy. The resulting digital models proved to be valuable assets for analysis and design within the workshop and provided insightful prospects for future research and territorial-scale projects.

We investigate the value distribution of dierence polynomials of entire and meromorphic functions, which can be viewed as the Hayman's conjecture. And we also study the uniqueness of dierence polynomials sharing a common value.

There is a growing interest in the endocannabinoid system and the gut microbiota. Both areas have been suggested to play a role in endometriosis, however this is yet to be studied comprehensively. The purpose of this narrative review is to identify the gaps in endometriosis research in the context of these two areas. It underscores the limited knowledge regarding the involvement of the endocannabinoid system and gut microbiota in endometriosis. Further research in these areas is essential to unlock the therapeutic potential of cannabis and enhance the understanding of endometriosis pathogenesis.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

This study introduces a gate design that uses pass transistor switches and enables the implementation of all nec- necessary logic gates with a single structure. This gate design can be used for efficient circuit resizing and creating secure obfuscated circuits. This work also presents simulation results that demonstrate the effectiveness of the gate in performing various logic gate operations.

Malassezia is a lipid-dependent genus of yeasts known for being an important part of the skin mycobiota. These yeasts have been associated in the development of skin disorders and cataloged as a causal agent of systemic infections under specific conditions, making them opportunistic pathogens. Little is known about the host-microbe interaction of Malassezia spp., and unraveling this implies the implementation of infection models. In this mini review we present different models that have been implemented in the fungal infections study with greater attention in Malassezia spp. infections. These models range from in vitro (cell cultures and ex vivo tissue), to in vivo (murine models, rabbits, guinea pigs, insects, nematodes, and amoebas). We additionally highlight the alternative models that reduce the use of mammals as model organisms, which have been gaining importance in the study of fungal host-microbe interactions. This is due to the fact that these systems have shown to have reliable results, which correlate with those obtained from mammalian models. Example of alternative models are Caenorhabditis elegans, Drosophila melanogaster, Tenebrio molitor, and Galleria mellonella. These are invertebrates that have been implemented in the study of Malassezia spp. infections in order to identify differences in virulence between Malassezia species.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Now day; the interest for the synthesis of heterocyclic compounds containing hydroquinoline fragments has increased tremendously due to their wide variety of pharmaceutical and industrial applications. This work details the synthesis of linear and fused heterocyclic systems containing hydroquinoline fragments and the pharmacological activity spectra of the synthesized compounds was predicted by in silico method using Prediction of Activity Spectra of Substances (PASS) program. 1,2,2,4-tetramethyl-1,2-dihydroquinoline-6-carbaldehyde 5a was reacted for three hours with a system of hydroxylammonium chloride/pyridinium chloride/toluene to produce 1,2,2,4-tetramethyl-1,2-dihydroquinoline-6-nitrile 7. N-benzyl-2,2,4-trimethyl-1,2,3,4-tetrahydroquinoline-6-carbaldehyde 6b and iodine reacted at room temperature in aqueous ammonia water, followed by aq. treatment with Na2S2O3 and produced N-benzyl-2,2,4-trimethyl-1,2,3,4-tetrahydroquinoline-6-nitrile 8. 30-60% 2-phenyl-1,3-oxazol-5(4H)-ones 9a,b; 10a,b were synthesized via the condensation reaction of N-alkylhydroquinoline-6-carbaldehydes 5a,b; 6a,b with hippuric acid in acetic acid. When activated 7-methylazolopyrimidines 11a,b were reacted with N-alkyl-2,2,4-trimethyl-1,2,3,4-tetrahydroquinoline-6-carbaldehydes 6a,b, the reaction produced 60–70% yield of 7-[(E)-2,2,4-trimethylhydroquinolin-6-ylidenemethyl]azolo[1,5-a]pyrimidin-6-yl carboxylic acids 12a,b. The condensation reaction of 7-hydroxy-1,2,2,4-tetramethyl-1,2-dihydroquinoline 3h with dimethylacetylenedicarboxylate (DMAD) and ethylacetoacetate afforded methyl (Z)-2-(5,7,7,8-tetramethyl-2-oxo-7,8-dihydrofuro[3,2-g]quinolin-3(2H)-ylidene)acetate 16 and 4,6,8,8,9-pentamethyl-8,9-dihydro-2H-pyrano[3,2-g]quinolin-2-one 17, respectively. The condensation reaction of 6-formyl-7-hydroxy-1,2,2,4-tetramethyl-1,2-dihydroquinoline 5e with methylene active compounds ethylcyanoacetate/dimethyl-3-oxopentanedioate/ ethylacetoacetate/diethylmalonate/Meldrum’s acid afforded 3-substituted dihydroquinoline containg coumarins 19 & 21. A pentacyclic coumarin 22 was obtained via the random condensation reaction of malononitrile with 5e in the presence of catalytic amount of piperidine in ethanol. The potential biological activities of the synthesized compounds were evaluated using PASS computer program. According to the prognosis, (E)-4-(N-alkylhydroquinolin-6-yl)-3-buten-2-ones, 13a, b & 14 showed high probability of being active (Pa) as the Gluconate 2-dehydrogenase inhibitor, Anti-allergic, Anti-asthmatic, and Anti-arthritic with the Pa value of 0.849-0.870. It was also found out that hydroquinolinecarbonitrile compounds 7 & 8 have a propensity to act as a good progesterone antagonists, anti-allergic, anti-asthmatic, and anti-arthritic (Pa = 0.276-0.827). Among the coumarin moieties containing hydroquinolines, compounds 17, 19a, and 19c were predicted to be good progesterone antagonists with the Pa values of 0.710, 0.630 and 0.615; respectively.

This research presents the design and characteristics of new wideband polarizer based on the square waveguide with irises. Matching and polarization characteristics of the polarizer have been simulated and optimized. Frequency dependences of the characteristics are presented. Developed polarizer can be applied in satellite information systems.

Nowadays, the transactions carried out with digital currencies are increasing. Citizens are asked to respond to growing challenges related to the sustainable management of digital currencies in their daily lives. However, due to the lack of digital skills of users, the sustainable management of digital currencies hides risks. The methodology of this study was based on the Digital Competence Framework for Citizens (DigComp) and is applied through a questionnaire completed by 443 respondents. The main objective was to evaluate their digital skills from the perspective of digital currency use. The analysis of the responses was carried out by using Structural Equation Modeling (SEM). The most important result from this research reveals that users of digital currencies are significantly capable of developing sustainable communication to solve everyday problems. At the same time, users of digital currencies mostly detect digital threats and effectively manage fake news without being affected by them. However, users of digital currencies consider that security issues are important, but only for transactions and not for their supporting functions. The study concludes with suggestions for improving the experience of digital currency users through individual actions, thus having a positive impact on the state and banking institutions.

The advancement of technology and the availability of specialized digital signal processing chips have made digital filter design and implementation more feasible in a variety of fields, including biomedical engineering. This paper makes two key contributions. First, it uses a genetic algorithm to optimize the coefficients of Finite Impulse Response (FIR) filters. Second, it conducts a case study on using genetic algorithms to optimize FIR filters for electrocardiogram (ECG) biomedical signal noise removal. The goal of the proposed filter design approach is to achieve the desired signal bandwidth while minimizing the side lobe level and eliminating unwanted signals using a genetic algorithm. The results of the comprehensive analysis of the impact of different genetic operators show that the genetic algorithm-based filter outperforms conventional filter designs.

It is important to realize the transformation behavior of wüstite because it greatly affects the final structure of the oxide layer and the surface quality of the steel products. In the present study, the transformation behaviors of the wüstite layer are examined under nearly-oxygen-free conditions, to simulate the cooling processes after the hot rolled strip is coiled. As the single phase wüstite was prepared at 950˚C, the 460˚C transformed oxide layer was composed of a mixture of iron and magnetite formed through eutectoid reactions. For the 750˚C-fabricated wüstite, only magnetite was observed after transformation, without iron precipitates and residual wüstite. It is speculated that the unusual transformation behavior of the low-temperature-made wüstite results from the pseudo-structural intermediate phase transformation between wüstite and magnetite. This pseudo-structure is a pre-transformed wüstite and of various concentration of ferrous ion, which is determined by the fabrication conditions. During the hot strip mill process, the so-called wet scale, wüstite, is produced continuously from finish mill to laminar flow sections and ended at 570˚C. Consequently, the final eutectoid transformation below 570˚C is dominantly controlled by the surface temperature ranged from 750˚C to 950˚C for low carbon steel.

A Challenging task in routine practice is finding distinction between benign and malignant paragangliomas and pheochromocytomas. The aim of this study is a comparative analysis of angiogenesis by assessing intratumoral microvascular density (MVD) with immunohistochemical (IHC) markers (CD31, CD34, CD105, ERG), and S100 immunoreactivity, Ki67 proliferative index, SDHB expressiveness, tumor size with one the most utilized score Pheochromocytoma of Adrenal Gland Scales Score (PASS), using tissue microarray (TMA) with 115 tumor samples, 61 benign (PASS&lt;4) and 54 potentially malignant (PASS ≥4). We found no notable difference between intratumoral MVD and potentially malignant behavior. Group of potentially malignant tumors are significantly larger in size, have lower intratumoral MVD, and decreased number of S100 labeled sustentacular cells. Both groups have low proliferative activity (mean Ki67 is 1,02 and 1,22 respectively). Most tumors maintains SDHB expression, only 6 cases (5,2%) showed a loss of expression (4 of them in PASS&lt;4 group and 2 in PASS≥4). PASS score is easy available for assessment, and complemented with markers of biological behavior completes risk stratification algorithm. Size is directly related with PASS score and malignancy. Intratumoral MVD is extensively developed but it is not crucial in evaluating the malignant potential.

The design of a mixed-mode proportional-integral-derivative (PID) controller circuit using current-feedback operational amplifiers (CFOAs) as active components is proposed. With the same circuit topology, the proposed configuration of three CFOAs, four resistors, and two capacitors is capable of performing the PID controller in all four operation modes: namely voltage mode, trans-admittance mode, current mode, and trans-impedance mode. Numerous mathematical analyses are conducted to determine the controller performance under ideal and non-ideal conditions. Additionally, the mixed-mode second-order lowpass filter is suggested, and also used to examine the workability of the proposed mixed-mode PID controller in a feedback control structure. The proposed PID controller is implemented with the commercially available IC-type CFOA AD844, and the simulation results are presented to illustrate the functionality of the controller and its closed-loop control system.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

Keywords: SAR; interferometry; bistatic

ChatGPT is gaining widespread acceptance for its ability to generate natural language sentences in response to various inputs and is expected to become a supplementary tool for diagnosing and determining treatment policies in clinical settings. ChatGPT was used to evaluate its ability to perform clinical inference and accuracy in answering questions on the 117th Japanese National Medical Licensing Examination held in February 2023. The exam questions were manually inputted into ChatGPT's window, and the accuracy of ChatGPT's responses was determined based on answers provided by a preparatory school. ChatGPT provided answers for 389 out of 400 questions, and its overall correct answer rate was 55.0%. The correct answer rate for 5-choice-1, 5-choice-2, and 5-choice-3 were 57.8%, 42.9%, and 41.2%, respectively. The highest correct answer rate was for the compulsory exam (67.0%), followed by the specific knowledge exam (54.1%) and the cross category exam (47.9%). The correct answer rate for non-image questions was 56.2% and for image questions, it was 51.5%. The study suggests that ChatGPT has potential to support healthcare professionals in clinical decision-making in Japanese clinical settings, but caution should be exercised in interpreting and using the answers generated by ChatGPT due to room for improvement in performance.

Aluminium alloys have evolved as suitable materials for automotive and aircraft industries due to their reduced weight, excellent fatigue properties, high-strength to weight ratio, high workability/formability, and corrosion resistance. Recently, the joining of similar and dissimilar metals have achieved huge success in various sectors. The processing of soft metals like aluminium, copper, iron and nickel have been fabricated using friction stir processing. Friction stir processing (FSP) is a microstructural modifying technique that uses the same principles as the friction stir welding technique. In the majority of studies on FSP, the effect of process parameters on the microstructure was characterized after a single pass. However, multiple passes of FSP is another method to further modify the microstructure in aluminium castings. This study is aimed at reviewing the impact of multi-pass friction stir processed joints of aluminium alloys and to identify a knowledge gap. From the literature that is available on multi-pass FSP, it has been observed that the majority of the literature focused on the processing of plates than the joints. There is limited literature reporting on multi-pass friction stir processed joints. This then creates a need to study further on multi-pass friction stir processing on dissimilar aluminium alloys.

Music cultural heritage, as an important component of cultural heritage, possesses significant cultural value and inheritance significance. With the development of society and the passage of time, these precious traditional music cultural heritages inevitably face the dilemma of gradual depletion or even disappearance. In the digital age, effectively protecting and inheriting these music cultural heritages has become an urgent problem to be addressed. Therefore, this paper proposes an application method based on digital twin technology, exploring how to protect and inherit music cultural heritages through digital twin technology. By leveraging digital twin technology, a virtual museum dedicated to showcasing the richness and historical connotations of music cultures is created, preserving and simulating the soundscapes of historical music eras. Through the integration of audio archives, 3D modeling, and interactive displays, users can immerse themselves in the experience of historical music in the digital space. This paper evaluates the feasibility and cultural preservation value of this digital music history museum through the creation of music digital twin technology instances and user survey feedback, and discusses the prospects of digital twins in the field of music cultural heritage.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

This paper presents a hydrodynamic numerical model for a pitching wave energy converter (WEC). The model uses potential wave theory and is based on Cummins' equation, with nonlinear hydrostatic restoring stiffness and excitation forces based on instantaneous body position and water surface elevation. The numerical model can include non-linear forces, like quadratic drag, power-take-off and other forces that may account for unknown viscous effects observed in experiments. The paper discusses the applicability and limitations of the code and presents the cases where assumptions and simplifications can be made. The goal is to conclude on the simplest, yet accurate, version of the model by evaluating its accuracy using experimental data. The case study for validation is Floating Power Plant's (FPP's) WEC [1]. In the full-scale commercial project, FPP's device consists of a semisubmersible platform hosting a wind turbine (5-8MW) and 4 WECs, each one connected to the platform by a rotation shaft. Due to the configuration of the platform, strong interactions occur between the WECs and the structure, as they are very closely spaced. In order to validate a numerical model able to simulate these hydrodynamic interactions, wave basin experiments with a similar but simplified setup were performed.

The aims of the study are: a) Describe the reactogenicity of WHO-approved two mRNA (Pfizer-BioNTech, Moderna) and two non-RNA vaccines (Oxford-AstraZeneca, Sinovac) among lactating mother and baby pairs; and b) compare and contrast the reactogenicity between mRNA and non-mRNA vaccines. A cross-sectional, self-reported survey was conducted amongst 1784 lactating women who received COVID-19 vaccinations. The most common maternal adverse reaction was a local reaction at the injection site; the largest minority of respondents, 43.7% (780/1784), reported experiencing worse symptoms when receiving the second dose compared to the first dose. There were no major reported adverse effects or behavioural changes in the breastfed infants. Among the respondents who received non-mRNA COVID-19 vaccinations, a majority reported no change in lactation but those who did more commonly reported an increase in milk supply, decrease in milk supply and pain in the breast. The more commonly reported lactation changes (fluctuations in breastmilk supply and pain in the breast) for the non-mRNA vaccines were similar to that of respondents who received mRNA vaccines. Our study, with a large cohort and wide geographical and racial mix, further augments earlier reported findings that COVID-19 vaccines are safe for breastfeeding mothers and her children.

We examine a linear q-difference differential equation which is singular in complex time t at the origin. Its coefficients are polynomial in time and bounded holomorphic on horizontal strips in one complex space variable. The equation under study represents a q-analog of a singular partial differential equation, recently investigated by the author, which comprises Fuchsian operators and entails a forcing term that combines polynomial and logarithmic type functions in time. A sectorial holomorphic solution to the equation is constructed as a double complete Laplace transform in both time t and its complex logarithm log t and Fourier inverse integral in space. For a particular choice of the forcing term, this solution turns out to solve some specific nonlinear q-difference differential equation with polynomial coefficients in some positive rational power of t. Asymptotic expansions of the solution relatively to time t are investigated. A Gevrey type expansion is exhibited in a logarithmic scale. Furthermore, a formal asymptotic expansion in power scale is displayed, revealing a new fine structure involving remainders with both Gevrey and q-Gevrey type growth.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

In this paper, the authors employ Mountain Pass Lemma, the method of weak solution regularization and Lyapunov function method to derive the unique existence of globally exponential stable positive stationary solution of a single-species model with diffusion and delayed feedback. The obtained stability criterion illuminates that under some suitable conditions, a certain internal competition is conducive to the overall stability of the population, and a certain amount of family planning is conducive to the overall stability of the population. A numerical example and three tables show the effectiveness of the proposed methods.

To enhance system reliability and mitigate vulnerabilities of the Global Navigation Satellite Systems (GNSS), it is common to fuse the Inertial Measurement Unit (IMU) and visual sensors with the GNSS receiver in the navigation system design, effectively enabling compensations with absolute position and reducing data gaps. To address shortcomings of traditional Kalman Filter (KF) such as sensor error, imperfect nonlinear system model, and KF estimation error, a GRU-aided ESKF architecture is proposed to enhance positioning performance. This study conducts Failure Mode and Effect Analysis (FMEA) to priories and identify the potential faults in the urban environment facilitating the design of improved fault-tolerant system architecture. The identified primary fault events are data association error and navigation environment error during fault conditions of feature mismatch, especially in the presence of multiple failure modes. A hybrid federated navigation system architecture is employed using a Gated Recurrent Unit (GRU) to predict state increments for updating the state vector in the Error Estate Kalman Filter (ESKF) measurement step. The proposed algorithm’s performance is evaluated in a simulation environment in MATLAB under multiple visually degraded conditions. Comparative results provide evidence that the GRU-aided ESKF outperforms standard ESKF and state-of-the-art solutions like VINS-Mono, End-to-End VIO, and Self-Supervised VIO, exhibiting higher efficiency in complex environments.