The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In this outlet, I’ve devised the concept of relation amid two points where these points are coming up to make situation which in that the set of objects are greed to represent the story of how to be in whatever situations when these two points have the styles of being everywhere in the highlights of the concept which are coming from the merits of these points where are eligible to make capable situation to overcome every situation when they’re participant in the hugely diverse situations which mean too styles of graphs with have the name or the general results for the general situation as possible as are.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

The fractal dimension of is identified in this paper. More importantly, the undertaken research has shown how affects the Koch snowflake . The study has demonstrated the existence of negative values of (Koch snowflake), which connects to a considerable number of extremely intriguing mathematical and physical research areas. The information-theoretic impact on the Sierpiniski Gasket dimension , which corresponds to , was treated in a more fundamental way. Notably, the credibility of this current study adds to the existing kThe fractal dimension of is identified in this paper. More importantly, the undertaken research has shown how affects the Koch snowflake . The study has demonstrated the existence of negative values of (Koch snowflake), which connects to a considerable number of extremely intriguing mathematical and physical research areas. The information-theoretic impact on the Sierpiniski Gasket dimension , which corresponds to , was treated in a more fundamental way. Notably, the credibility of this current study adds to the existing knowledge for the information- theoretic fractal dimensions. On another applicative note, this paper offers some potential applications of fractal dimension to smart cities. The investigation of the threshold theorems for and in terms of the triad is part of the next study phase. Additionally, investigating the newly obtained 's corresponding arbitrary Sierpinski Gasket for the first time.applicative note, this paper offers some potential applications of fractal dimension to smart cities. The investigation of the threshold theorems for and in terms of the triad is part of the next study phase. Additionally, investigating the newly obtained 's corresponding arbitrary Sierpinski Gasket for the first time.

New setting is introduced to study resolving number and chromatic number alongside dominating number. Different types of procedures including set, optimal set, and optimal number alongside study on the family of neutrosophic hypergraphs are proposed in this way, some results are obtained. General classes of neutrosophic hypergraphs are used to obtains these numbers and the representatives of the colors, dominating sets and resolving sets. Using colors to assign to the vertices of neutrosophic hypergraphs and characterizing resolving sets and dominating sets are applied. Some questions and problems are posed concerning ways to do further studies on this topic. Using different ways of study on neutrosophic hypergraphs to get new results about numbers and sets in the way that some numbers get understandable perspective. Family of neutrosophic hypergraphs are studied to investigate about the notions, dimension and coloring alongside domination in neutrosophic hypergraphs. In this way, sets of representatives of colors, resolving sets and dominating sets have key role. Optimal sets and optimal numbers have key points to get new results but in some cases, there are usages of sets and numbers instead of optimal ones. Simultaneously, three notions are applied into neutrosophic hypergraphs to get sensible results about their structures. Basic familiarities with neutrosophic hypergraphs theory and hypergraph theory are proposed for this article.

New notion of dimension as set, as two optimal numbers including metric number, dimension number and as optimal set are introduced in individual framework and in formation of family. Behaviors of twin and antipodal are explored in fuzzy(neutrosophic) graphs. Fuzzy(neutrosophic) graphs, under conditions, fixed-edges, fixed-vertex and strong fixed-vertex are studied. Some classes as path, cycle, complete, strong, t-partite, bipartite, star and wheel in the formation of individual case and in the case, they form a family are studied in the term of dimension. Fuzzification(neutrosofication) of twin vertices but using crisp concept of antipodal vertices are another approaches of this study. Thus defining two notions concerning vertices which one of them is fuzzy(neutrosophic) titled twin and another is crisp titled antipodal to study the behaviors of cycles which are partitioned into even and odd, are concluded. Classes of cycles according to antipodal vertices are divided into two classes as even and odd. Parity of the number of edges in cycle causes to have two subsections under the section is entitled to antipodal vertices. In this study, the term dimension is introduced on fuzzy(neutrosophic) graphs. The locations of objects by a set of some junctions which have distinct distance from any couple of objects out of the set, are determined. Thus it’s possible to have the locations of objects outside of this set by assigning partial number to any objects. The classes of these specific graphs are chosen to obtain some results based on dimension. The types of crisp notions and fuzzy(neutrosophic) notions are used to make sense about the material of this study and the outline of this study uses some new notions which are crisp and fuzzy(neutrosophic). Some questions and problems are posed concerning ways to do further studies on this topic. Basic familiarities with fuzzy(neutrosophic) graph theory and graph theory are proposed for this article.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Acoustic Radiation Forced Impulse (ARFI) is an ultrasound integrated method, measuring stiff-ness by point shear wave elastography. To evaluate the diagnostic performance of ARFI of the liver and of the spleen, combined with spleen dimension and platelet count, in predicting clinical events in cirrhosis, a prospective and cross-sectional study was conducted between February 2017 and February 2021. The following ratio scores with ARFI measurements were performed: ALSDP (ARFI Liver-Spleen Diameter-to-Platelets ratio score), ASSDP (ARFI Spleen-Spleen Diam-eter-to-Platelets ratio score), ASSAP (ARFI Spleen-Spleen Area-to-Platelets ratio score), ALSAP (ARFI Liver-Spleen Area-to-Platelets ratio score). In 100 enrolled subjects, spleen ARFI, ASSDP, ASSAP, were significantly associated with high-risk oesophageal varices (HRVs) in the prospec-tive short- and long-term follow-up and in the cross-sectional study (p 0.7). ARFI-ratio scores can predict, in cirrhotic patients, the risk of developing HVRs in short and long-term period.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

This comprehensive review paper provides a detailed analysis of the extraction methods employed in the dimension stone industry. Natural rock materials used in construction, have been historically extracted using primitive techniques such as thermal shock, hammer and chisel, and plug and feather. However, significant technological advancements have revolutionized the industry, leading to the widespread adoption of mechanized methods. One highly efficient technique is diamond wire cutting, which involves the utilization of diamond-engraved bits affixed to a tensioned steel wire. This method has demonstrated remarkable capabilities in minimizing waste generation and ensuring exceptional machining quality. Nonetheless, challenges such as high operating costs and wire breakage persist and require further investigation. In addition to diamond wire cutting, this review explores the utilization of circular diamond saws and frame sawing as alternative extraction methods. The geotechnical characteristics of the stone play a critical role in the selection of appropriate machinery, and researchers worldwide have conducted numerous studies to investigate the impact of each parameter on the extraction efficiency of these mechanized techniques. Moreover, controlled blasting with explosives emerges as a promising alternative for dimension stone extraction, warranting further exploration and optimization.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

The dominant view of cleaning compulsion as a dimension of OCD is that it is motivated by contamination anxiety. However, in daily life, much cleaning is undertaken as part of tidying one’s home. Such cleaning as well as the other tidying chores may equally assume obsessive-compulsive proportions. However, empirical interest in this phenomenon has remained sparse so far. This article aims to increase awareness of this ill-acknowledged symptom cluster among OCD researchers and to invite them to investigate it. After the introduction, clinical evidence for this OCD dimension is dealt with. Next, empirical studies with OCD inventories, which contain items referring to compulsive tidying, are discussed. Two of these made use of an OCD-inventory, devised by the present author. These also provide the data for the main investigation to be discussed in this paper. In that latter study, six OCD-item clusters, among which tidying compulsion, are predicted. These predictions are tested by evaluating and comparing the item-cluster correlations of all six clusters. These also offer a basis to optimize the clusters toward more homogeneous and distinct ones. By comparing predicted with final clusters, the items can be qualified as either hits, false positives, or false negatives. This output provides the details for revising the predictions, but also allows for calculating the values of two global “goodness-of-fit” measures for each predicted cluster. Though the results do not completely endorse the predicted composition of part of the clusters in the second sample, tidying compulsion is doing rather well. To determine the incidence of tidying compulsion based on the cluster scores, decisions had to be made about what constitute a cluster score, how its gravity can be estimated, and what should be the cut-off per cluster to divide the sample into clinical and subclinical cases on each cluster. If these ‒ unavoidably arbitrary ‒ decisions are accepted, both samples show an incidence of tidying compulsion of around 25%. After a brief critical evaluation of all discussed studies, it is concluded that the evidence presented, though modest, is solid enough to warrant further research into tidying compulsion.

Nietzsche is almost always regarded as one of the thinkers who advocate extreme individualism, totally indifferent to or exclusively polemical towards the public human dimension. While this is very difficult to contradict, if we read his texts carefully we can see how his constant celebration of the individual runs parallel to an acute awareness of living in a new era, which he defined as ‘the century of the multitude and the masses’. The herd, conformism, mediocrity, public opinion: a civilisation in which community attempts suffocate all individual inspiration, and which therefore seems to row in the opposite direction. Although Nietzsche often uses collective life merely as a negative pole for more effectively emphasising the individual, his provocative words—pushed to the limits of the inexorable victory of the herd and of the paradoxical impossibility of all that is ‘public’—offer us a direct testimony of the tragic way of life of the man of his time. This provides us with an extremely clear and interesting phenomenological cross-section of the social sphere, as well as a very finely tuned and valuable seismograph for the continual monitoring of our everyday coexistence with and perception of the constantly incumbent dangers of its degeneration.

In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

So called Higuchi’s method of fractal dimension estimation is widely used and the term Higuchi’s fractal dimension even occurs in many publications. This paper deals with this method from mathematical point of view. Terms distance and dimension and its basic properties are explained and Higuchi’s dimension according the original source is defined. Definition of Higuchi’s dimension was comparated with mathematical definition of the distance and dimension. It is showed, that the definition of the Higuchi’s dimension does not satisfy axioms of distance and dimension. So called Higuchi’s method and Higuchi’s dimension are mathematically incorrect. Therefore, all results achieved by this method are scientifically unreliable.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

This work is an addition to the previously developed two-dimensional model of the shock-plasma interaction extending it into the third dimension. The model allows tracing the evolution of the state of the hypersonic flow and the shock front refracted at a thermal discontinuity. The advantages of using the spherical coordinate system for this type of the problems include more transparency in interpreting the solution and a shortened calculation procedure, because all the changes to the front become reduced to one distortion component only. Although the vorticity generation triggered at the interface is the consequence of the refraction and tied to the steep changes of the front, it is shown here that it is not because of an instant parameter jump at the interface due to refraction itself.

Energy is needed by cancer cells to stay alive and communicate with their surroundings. The primary organelles for cellular metabolism and energy synthesis are mitochondria. Researchers recently proved that cancer cells can steal immune cells' mitochondria using nanoscale tubes. This finding demonstrates the dependence of cancer cells on normal cells for their living and function. It also denotes the importance of mitochondria in cancer cells’ biology. Emerging evidence has demonstrated how mitochondria are essential for cancer cells to survive in the harsh tumor microenvironment, evade the immune system, obtain more aggressive features, and resist treatments. For instance, functional mitochondria can improve cancer resistance against radiotherapy by scavenging the released reactive oxygen species. Therefore, targeting mitochondria can potentially enhance oncological outcomes, according to this notion. The patients' reactions to radiation are varied, ranging from a complete response to even cancer progression during treatment. This concept illustrates how different levels of mitochondrial metabolism might contribute to this heterogeneity. Considering this notion can help to improve personalized oncological treatments. This article outlines the importance of mitochondrial metabolism in cancer biology and personalized treatments.

During few last years, climate change including global warming which is attributed to human activities and also its long-term adverse effects on the planet’s functions have been identified as the most challenging discussion topics which have arisen many concerns and efforts to find the possible solutions. Since the warmth arising from Earth’s landscapes affects the world’s weather and climate patterns, we decided to study the changes in the Land Surface Temperature (LST) patterns in different seasons through non-linear methods. Here, we particularly want to estimate the non-integer dimension and fractal structure of the land surface temperature. For this study, the (LST) data has been obtained during the daytime by the Moderate Resolution Imaging Spectroradiometer (MODIS) on NASA’s Terra satellite. Depending on what time of the year data has been collected, temperatures change in different ranges. Since equatorial regions remain warm, and Antarctica and Greenland remain cold, and also because altitude affects temperature, we selected Riley County in the U.S. state of Kansas, which does not belong to any of this type locations and we are interested to observe the seasonal changes in temperature in this county. The results of the present study show that the Land Surface Temperature (LST) belongs to the class of fractal process with non-integer dimension.

Consider a robot that is navigating in a space modeled by a graph, and that wants to know its current location. It can send a signal to determine how far it is from each landmark among a set of fixed landmarks. We study the problem of computing the minimum required number of landmarks, and where they should be placed so that the robot can always determine its location. Since the problem is an NP-complete problem, the robot's responses to the actions are slow. To accelerate this response, we can use the parallel version of this problem. In this work, we introduce a new parallel implementation for determining the metric dimension of a given graph. We run the proposed algorithm on a symmetric multi-processing (SMP) cluster using C programming language and the Message Passing Interface (MPI) library. Finally, we run our implementation on four categories of graphs (the tracks in which the robot moves): a cycle graph Cn, a path graph Pn, a triangular snake graph and a ladder graph Ln. Preliminary computational results indicate that the metric dimension problem is an NP-complete problem and prove the ability of the proposed algorithm to achieve a speedup of 6 for 8 processors.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

While the majority of previous studies assessing pain-related variables in psychopaths used electric shocks, little is known about the effectiveness of alternative pain-inducing methods to increase emotional responses such as fear and anxiety. A small sample of healthy undergraduate men (N = 15) was recruited to assess the effectiveness of a heat stimulus to induce pain in an immediate versus delayed punishment paradigm. Although pain catastrophizing, anxiety, and threat of pain did not increase throughout the experiment, participants experienced a significant increase of fear of pain and pain intensity, indicating that the heat stimulus was effective in inducing pain. Furthermore, subjects were slower in initiating the pain stimulus during the first five trials, but no time difference was found during the 15 remaining trials. No correlation was found between psychopathic traits and pain-related variables, with the exception of inconsistent results within the Fearless Dominance factor. Findings are discussed in terms of improvement for a larger scale study involving psychopathic individuals.

The study aimed to determine the effect of heat stress (HS) on reproductive parameters [calving to first service (CTFS) and first service conception rate (FSCR)] and general physiological responses [rectal temperature (RT) and respiratory rate (RR)] in tropical Holstein Friesian dairy cows raised in Ratchaburi province, Thailand. Cows were divided into a moderate HS (n = 22) and a mild HS (n = 22) group. Cycling cows were detected and injected with PGF2α at the beginning of the experimental period. Reproductive and physiological parameters were recorded. The average temperature humidity indices experienced by the cows were 80.67 ± 0.79 and 77.81 ± 1.09 for the moderate and mild HS groups, respectively. Cows showed significantly lower RT and RR in the mild (38.47 ± 0.21°C and 41.04 ± 4.55 bpm, respectively) than in the moderate HS group (38.87 ± 0.15°C and 51.17 ± 10.52 bpm). Under mild HS, cows showed a better response to injection of PGF2α than those under moderate HS. The percentage of cows that ovulated after being induced by PGF2α and showed estrus signs was higher in the mild than the moderate HS groups (54.55% versus 18.18%). Furthermore, the FSCR of cows under mild HS tended to be higher than in the moderate HS group (54.55 % and 42.11%, respectively), while the average CTFS interval was significantly shorter under mild than moderate HS (69.47 ± 18.18 and 84.60 ± 27.68, respectively). These results indicate that HS impairs reproductive performance in cross-bred Holstein cows, especially in moderate HS conditions.

Considering the increasing number of women entering the accounting profession; it is timely to explore inequalities that still exist; and consider what policy processes continue to forge inequalities between men and women. Through a SLR of accounting and management journals during the period 1994-2017 we assess the different dynamics that have shaped inequalities between men and women, presenting both employee and employer perspectives of professional enhancement. The study is framed around conceptualizations of gendered organizations and highlights how cultural and social practices impact men and women differently. Our study finds there are still arrays of organization practices that have profound gendered effects. Our study shows that there are commonalities in research which include HR practices of recruitment, selection, and advancement; perceptions of women's visibility and invisibility at work; motherhood and childcare responsibilities; and discourses of the glass ceiling that constitute barriers to women's progression. Most importantly we reveal that constraints nowadays are similar to those identified in the 90s. We explored these gendered constructions and suggest relevant HR strategies that can aid women's advancement.

The increasing spatial and spectral resolution of hyperspectral imagers yields detailed spectroscopy measurements from both space-based and airborne platforms. Machine learning algorithms have achieved state-of-the-art material classification performance on benchmark hyperspectral data sets; however, these techniques often do not consider varying atmospheric conditions experienced in a real-world detection scenario. To reduce the impact of atmospheric effects in the at-sensor signal, atmospheric compensation must be performed. Radiative Transfer (RT) modeling can generate high-fidelity atmospheric estimates at detailed spectral resolutions, but is often too time-consuming for real-time detection scenarios. This research utilizes machine learning methods to perform dimension reduction on the transmittance, upwelling radiance, and downwelling radiance (TUD) data to create high accuracy atmospheric estimates with lower computational cost than RT modeling. The utility of this approach is investigated using the instrument line shape for the Mako long-wave infrared hyperspectral sensor. This study employs physics-based metrics and loss functions to identify promising dimension reduction techniques. As a result, TUD vectors can be produced in real-time allowing for atmospheric compensation across diverse remote sensing scenarios.

The majority of the population in developing countries resides in the rural area. Development itself cannot address the challenges of the rural area since its economic, political and environmental landscape is different from an urban area. The paper attempts to assess the rural dimension aspect of Nepali Agriculture Policy since rural development and agricultural development is closely resembled due to an agrarian-based economy of the country and a large rural population. Therefore, a critical review of National Agriculture Policy, 2004 (NAP-2004) was carried out under “Commercialization of Agriculture”, “Food Security”, “Rural Infrastructure”, “Gender”, “Climate Change” and “Social Inclusion” thematic area. The results showed that NAP-2004 satisfactorily address rural development albeit ample space for improvement. The findings of the paper could be beneficial to policymakers and development workers in the field of rural development and agriculture along with academicians having interest in it.

Since their discovery in 1993, numerous microRNAs (miRNAs) have been identified in humans and other eukaryotic organisms, and their role as key regulators of gene expression is still being elucidated. It is now known that miRNAs not only play a central role in the processes that ensure normal development and physiology, but they are often dysregulated in various diseases. In this review, we present an overview of the role of miRNAs in normal renal development and physiology, in maladaptive renal repair after injury, and in the pathogenesis of renal parenchymal diseases. In addition, we describe methods used for their detection and their potential as therapeutic targets. Continued research on renal miRNAs will undoubtedly improve our understanding of diseases affecting the kidneys and may also lead to new therapeutic agents.

In the current work, the stable queueuing system's Generalised Z-Entropy (GZE) of Rényian formalism is examined in its fractal dimension. Notably, fractal dimension’s resulting behaviour that corresponds to the GZE parameters is examined through numerical tests. This research makes a substantial generalization in the literature by fusing fractal geometry and information theory to shed light on how entropy and complexity interact. More fundamentally, the significant role of fractal dimension to advance Big Data Analytics(BDAs) is highlighted. Closing remarks combined with open problems and the next phase of research are provided.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

Entropy as a mathematical concept is the first of its own kind, and second to none. Barely one or two papers in literature have investigated fractal dimensions of very basic entropies, such as Shannon, Tsallis, and Rényi entropic expressions. This was a thoughtful inspiration to delve into a step forward towards a unified information- theoretic fractal theory. The storytelling of this current paper starts by introducing my third entropy formula, namely Ismail’s entropy, , as a novel generalization to Shannonian entropy with a visionary link to both long- and short-range interactions, (LRIs), (SRIs) respectively. Clearly, this would generate a fourfold unification with statistical mechanics as well as contemporary physics. Hence, this adds more credibility and weight for this study. The fractal dimension of , is identified in this paper. As an essential part of this work, it was influential to spotlight the importance of fractal geometry to space industry as well as education, which is crucial to develop our societies. Thus, some potential fractal applications to CubeSat Technologies and Education are highlighted. So, will the deep search for more ground-breaking research has come to an end. Certainly, not. This was another inspiration to propose new open problems to widen research gates to the scientific community for more research pathways. Consequently, the paper ends with closing remarks combined with some challenging open problems and the next phase of research.

(1) Background: Breast cancer is the second leading cause of cancer death among women. The accurate prediction of survival intervals will help physicians make informed decisions on treatment strategies or the use of palliative care for patients; (2) Methods: The gene expression is predictive and correlates to patient prognosis. To establish a reliable prediction tool, we collected the RNA-seq data of breast cancer patients, a total of 1187 RNA-seq data (median age 58 years), in FPKM format from the TCGA database. Among them, 144 RNA-seq data with date of death information was selected to establish the SaBrcada-AD dataset. We first normalized the SaBrcada-AD dataset to transcripts per million (TPM) to build survival prediction model SaBrcada. After normalization and dimension raising, the differential gene expression data were used for testing eight different deep learning architectures. Among them, GoogLeNet performed the best. Considering the effect of age on prognosis, we examined all ages between the lower and upper quartiles of patient age for a stratified random sampling test; (3) Results: Stratifying by age based on a cut-off of 61 years of age improved the accuracy of SaBrcada compared to previous findings, resulting in an accuracy of 0.798. We also built a free website tool to provide 5 kinds of predicted survival period information for clinician reference; (4) Conclusions: We established a breast cancer survival analysis prediction model, SaBrcada, and a website tool with the same name. Through this highly reliable survival analysis model and website tool, information on survival intervals will be provided for clinicians as part of precision medicine.

The present paper proposes a fractal analysis of the Covid-19 dynamics in 45 European countries. We introduce a new idea of using the box-counting dimension of the epidemiologic curves as a means of classifying the Covid-19 pandemic in the countries taken into consideration. The classification can be a useful tool in deciding upon the quality and accuracy of the data available. We also investigated the reproduction rate, which proves to have significant fractal features, thus enabling another perspective on this epidemic characteristic. Moreover, we studied the correlation between two meteorological parameters: global radiation and daily mean temperature and two Covid-19 indicators: daily new cases and reproduction rate. The fractal dimension differences between the analysed time series graphs could represent a preliminary analysis criterion, increasing research efficiency. Daily global radiation was found to be stronger linked with Covid-19 new cases than air temperature (with a greater correlation coefficient -0.386, as compared with -0.318), and consequently it is recommended as the first-choice meteorological variable for prediction models.

Suitable soil structure and nutrient security are important for plant growth and development, characteristics of soil fractal dimension and distribution of physical and chemical properties and their interactions play an important role in studying the stability of soil structure and water and fertilizer cycles. As a sustainable management model, intercropping has positive benefits for erosion control, spatial optimization of resources, as well as improving system productivity. The effects of four intercropping methods on soil fractal dimension and physicochemical properties were investigated by intercropping Salvia miltiorrhiza with forage and S. miltiorrhiza with forest under typical karst rock desertification habitats in Guizhou. The results showed that soil nutrient content of intercropping was significantly higher than that of monoculture, the organic carbon content of soil grown under forest is higher than other treatments, and there was a non-significant change in soil water content of intercropping compared with monoculture. The soil fine-grained matter of intercropping was significantly higher than that of monoculture, while the soil fractal dimension showed a tendency to become larger with the increase of fine-grained matter. The intercropping planting, due to its component types and spatial and temporal configurations, leads to differences in soil water and fertilizer interactions, which can be combined with other ecological restoration measures to optimize the composite model and jointly promote the restoration and development of ecologically fragile areas.

With the development of energy internet, integrated energy system can effectively reduce carbon emissions and improve the utilization of renewable energy. In this paper, a low-carbon optimal scheduling model of integrated energy system considering heat loss of heat network pipeline is proposed. Based on the study of concentrating solar power (CSP) plant and heat storage tank (HS), an optimal scheduling model is established, which takes system operation cost, environmental pollution and penalty cost of abandoning wind and solar energy as objectives. Through the analysis of example results, it is proved that the model proposed in this paper can achieve the goal of reliable, low-carbon and economic operation of the system. At the same time, it shows that CSP unit can reduce the operation cost of system and increase energy coupling and utilization.

We present a new theory to explain the expansion of the universe that augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension. The theory is tested by accurately modelling against stellar luminosity data that is available for redshifts, z

Matrix asphalt material has poor road performance, which is improved by adding polymer modified agents. The original asphalt material experiment research has a certain limitation in that it cannot truly expose the mechanism and influence of modifiers on asphalt materials. To explore the gain effect of the modified agent on the asphalt material's road performance, the molecular dynamic simulation technology is used to explain its mechanism in the micro dimension. The three parameters of the free volume score, radial distribution function and average directional shift diffusion coefficient are analysed to improve the performance of the modifier on asphalt material, an exploration of the microdimension shows that the amount of SBS modifiers is 6% and the amount of rubber modified asphalt material is 22%. The improvement of materials is better than that of rubber modifiers.

This article introduces a new fractional approach to the concept of information dimension of complex networks, based on a (q,q′)-entropy proposed in the literature. The q parameter measures how far is the number of subsystems (for a given size ε) from the mean number of overall sizes. The q′ (interaction index) measures when the interactions between subsystems are greater (q′&gt;1), lesser (q′&lt;1) or equal to the interactions into these subsystems. The computations of the proposed information dimension are carried out on several real-world and synthetic complex networks. The results from the proposed information dimension are compared with those from the information dimension based on the Shannon entropy.

Cell-penetrating peptides (CPPs), a group of small peptides capable of promoting the transport of molecular cargo across the plasma membrane, have become important tools in promoting the cellular uptake of exogenously delivered macromolecules. GV1001, a peptide derived from a reverse-transcriptase subunit of telomerase (hTERT) and developed as a vaccine against various cancers, reportedly has unexpected CPP properties. Unlike typical CPPs, such as the HIV-1 TAT peptide, GV1001 enabled the cytosolic delivery of macromolecules such as proteins, DNA and siRNA via extracellular heat shock protein 90 (eHSP90) and 70 (eHSP70) complexes. The eHSP-GV1001 interaction may have biological effects in addition to its cytosolic delivery function. GV1001 was originally designed as a MHC class II-binding cancer epitope, but its CPP properties may contribute to its strong anti-cancer immune response relative to other telomerase peptide-based vaccines. Cell signaling via eHSP-GV1001 binding may lead to unexpected biological effects, such as direct anticancer or antiviral effects. In this review, we focus on the CPP effects of GV1001 bound to eHSP90 and ehsp70.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

We propose a notion of a ternary skew-symmetric covariant tensor of 3rd order, consider it as a 3-dimensional matrix and study a ten-dimensional complex space of these tensors. We split this space into a direct sum of two five-dimensional subspaces and in each subspace there is an irreducible representation of the rotation group SO(3)↪SO(5). We find two independent SO(3)-invariants of ternary skew-symmetric tensors, where one of them is the Hermitian metric and the other is the quadratic form. We find the stabilizer of this quadratic form and its invariant properties. Making use of these invariant properties we define a SO(3)-irreducible geometric structure on a five-dimensional complex Hermitian manifold. We study a connection on a five-dimensional complex Hermitian manifold with a SO(3)-irreducible geometric structure, find its curvature and torsion. The structures proposed in this paper and their study are motivated by a ternary generalization of the Pauli’s principle proposed by R. Kerner.

Restoration experience is a positive response against the ever-increasing problem of stress. It is recovery of attentional capacity, clearing random thoughts and feelings of relaxation and calmness. Although there is a body of research on investigating the impact of open green space characteristics on psycho- logical restoration through attention restoration theory and supportive environment theory, there is little knowledge on how the interaction among these characteristics could promote restorative outcomes. To address this problem, using Perceived Sensory Dimension (PSD) for open green space qualities and Perceived Restorativeness (PR) as the property of restorative environment, this study assessed the extent to which the PSD and PR impact on restoration experience. Using 444 screened surveys, a Partial Least Square Structural Equation Model (PLS-SEM) was developed and the validity and reliability of it, was demonstrated. Extensive analysis of the results showed how environmental qualities can promote restoration experience using a sample of university students. These results provide information for landscape architecture and planning researchers to promote the development of open spaces as a resource of psychological restoration and stress relief.

The plate fin heat exchanger is the compact heat exchanger applied in many industries because of its high thermal performance. To enhance the heat transfer of plate fin heat exchanger in further, three new kinds of wavy plate fins, namely perforated wavy fin, staggered wavy fin and discontinuous wavy fin are proposed and investigated by CFD simulations. The effects of key design parameters, including that of waviness aspect ratios, perforation diameters, stagger ratios and breaking distance are investigated, respectively, with the Reynolds number changes from 500 to 4500. It is found that due to the swirl flow and efficient mixing of fluid, the perforation, serration and breaking techniques are beneficial for the enhancement of heat transfer compared to the traditional wavy fin. At the same time, serration is beneficial to reduce the friction factor, and the breaking technique can reduce heat transfer area as well as enhance heat transfer performance. Through the performance evaluation criteria, the staggered wavy fin has an advantage over the small waviness aspect ratio compared to the perforated wavy fin. The maximum performance evaluation criteria (PEC), as high as 1.24, can be obtained for the perforated wavy fin at the largest waviness aspect ratio.

If "quantization is an art" then it can be greatly rened by adopting cyclic time formalism. In past papers we have proven the effectiveness of a formulation of physics based on cyclic relativistic time. Now we can demonstrate in a general way, by using theorems of Geometric Quantization, that the Poisson brackets of intrinsically cyclic time dynamics directly imply the ordinary canonical commutation relations and the other Dirac's rules of canonical Quantum Mechanics. In other words, according to our result, canonical quantization is an implicit way of imposing intrinsically cyclic time dynamics without explicitly saying that time is a cyclic dimension.

In this paper we use the additive thermodynamic formalism to obtain new bounds of the Hausdorff and box-counting dimension of certain non conformal hyperbolic repellers defined by piecewise smooth expanding maps on a $d$-dimensional smooth manifold $M$.

In this research, an attempt was made to reduce the dimension of wavelet-ANFIS/ANN (artificial neural network/adaptive neuro-fuzzy inference system) models toward reliable forecasts as well as to decrease computational cost. In this regard, the principal component analysis was performed on the input time series decomposed by a discrete wavelet transform to feed the ANN/ANFIS models. The models were applied for dissolved oxygen (DO) forecasting in rivers which is an important variable affecting aquatic life and water quality. The current values of DO, water surface temperature, salinity, and turbidity have been considered as the input variable to forecast DO in a three-time step further. The results of the study revealed that PCA can be employed as a powerful for dimension reduction of input variables and also to detect inter-correlation of input variables. Results of the PCA-Wavelet-ANN models are compared with those obtained from Wavelet-ANN models while the earlier one has the advantage of less computational time than the later models. Dealing with ANFIS models, PCA is more beneficial to avoid Wavelet-ANFIS models creating too many rules which deteriorate the efficiency of the ANFIS models. Moreover, manipulating the Wavelet-ANFIS models utilizing PCA leads to a significant decreasing in computational time. Finally, it was found that the PCA-Wavelet-ANN/ANFIS models can provide reliable forecasts of dissolved oxygen as an important water quality indicators in rivers.

The interlaminar strength of mechanically interlocked polymer-metal-interfaces is strongly dependent on the surface structure of the metal component. Therefore, this contribution assesses the suitability of the fractal dimension for quantification of the surface structure as well as interlaminar strength prediction of aluminum/polyamide 6 polymer-metal-hybrids. Seven different surface structures, manufactured by blasting, combined blasting and etching, thermal spraying and laser ablation, are investigated. The experiments are carried out on a novel butt-bonded hollow cylinder testing method that allows shear and tensile strength determination with one specific specimen geometry. The fractal dimension of the metal surfaces is derived from cross-sectional images. For comparison, the surface roughness slope is determined and related to the interlaminar strength. Finally, a fracture analysis is conducted. For the investigated material combination, the experimental results indicate that the fractal dimension is an appropriate measure for predicting the interlaminar strength

Sparse recovery of fluid flows using data-driven proper orthogonal decomposition (POD) basis is systematically explored in this work. Fluid flows are manifestations of nonlinear multiscale PDE dynamical systems with inherent scale separation that impact the system dimensionality. Given that sparse reconstruction is inherently an ill-posed problem, the most successful approaches require the knowledge of the underlying basis space spanning the manifold in which the system resides. In this study, we employ an approach that learns basis from singular value decomposition (SVD) of training data to reconstruct sparsely sensed information. This results in a set of four control parameters for sparse recovery, namely, the choice of basis, system dimension required for sufficiently accurate reconstruction, sensor budget and their placement. The choice of control parameters implicitly determines the choice of algorithm as either $l_2$ minimization reconstruction or sparsity promoting $l_1$ norm minimization reconstruction. In this work, we systematically explore the implications of these control parameters on reconstruction accuracy so that practical recommendations can be identified. We observe that greedy-smart sensor placement provides the best balance of computational complexity and robust reconstruction for marginally oversampled cases which happens to be the most challenging regime in the explored parameter design space.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

Three Dimensional Variational data assimilation or analysis (3DVAR) is one of most classical methods for providing the initial values for numerical models. In this method, the dimensions of the background error covariance and the observational error covariance matrices are large. Therefore, it is difficult to get the inverse of the covariance matrices and to reduce the orders of these matrices without information loss. With the use of the Sylvester Equation, on the basis of a new linear regression, a new cost function for 3DVAR was given. For the first-guess m×n field, there is an approximate 1−(m²+n²)/(mn×mn) reduction with m>1 & n>1 by using the cost function. The results of the numerical experiments show that the effect of this algorithm is no worse than that of the old cost function for 3DVAR.

Master Valentim’s fountain became an important historical patrimony for Brazil, being portrayed by famous artists among them Jean-Baptiste Debret. In 1938, it was registered as cultural heritage by the Brazilian National Historical and Artistic Heritage Institute (IPHAN), and in 1990 it was subjected to excavation and restoration works. The fountain was built in Gneiss and Lioz limestone, with metallic plates and mortar connecting the Gneiss blocks. Currently, deteriorations in the fountain stones can be observed such as light stains and some aesthetic modifications caused by inadequate restorations. Petrography, XRF, XRD, Physical Properties, Colorimetry, Electrical Conductivity, ICP-OES, SEM-EDX, and TGA were performed in order to characterize the Gneiss blocks, the metallic plates, the stones used in previous restorations, as well as light stains observed on the Gneiss blocks. The petrography and XRD analyses inferred that light stains may have been caused by the formation of an insoluble salt as a result of the association of the lead from the plates with other elements. The XRD analysis on the light staining area indicated presence of cerussite (PbCO₃), and anglesite (PbSO₄), which are the probable cause of the light stains. The SEM-EDX results suggested that sulfur is the main element associated to lead.

Material efficiency is a key element of new thinking to address the challenges of reducing impacts on the environment and of resource scarcity, whilst at the same time meeting service and functionality demands on materials. Directly related to material efficiency is the concept of the Circular Economy, which is based on the principle of optimising the utility embodied in materials and products through the life cycle. Whilst steel, as a result of high recycling rates, is one of the most ‘circular’ of all manufactured materials, significant opportunities for greater material efficiency exist, which are yet to be widely implemented. In the field of Life Cycle Management, Life Cycle Assessment (LCA) is commonly used to assess the environmental benefits of recovering and recycling materials through the manufacturing supply chain and at end-of-life. As well as containing information to calculate environmental impacts, LCA models also provide the flows of materials through the product life cycle and can also be used to quantify material efficiency and the circularity of a product system. Using an example taken from renewable energy generation, this paper explores the correlation between product circularity and the environmental case for strategies designed to improve material efficiency. An LCA-based methodology for accounting for the recovery and re-use of materials from the supply chain, and at end-of-life, is used as the basis for calculating the carbon footprint benefits of five material efficiency scenarios. Resulting carbon footprints were then compared with a number of proposed material circularity indicators. Two conclusions from this exercise were that i) LCA methodologies based around end-of-life approaches are well placed for quantifying the environmental benefits of material efficiency and circular economy strategies and ii) when applying indicators relating to the circularity of materials these should also be supported by LCA studies.

Many microbes live in habitats below their optimum temperature. Retention of metabolic heat by aggregation or insulation would boost growth. Generation of excess metabolic heat may also provide benefit. A cell that makes excess metabolic heat pays the cost of production, whereas the benefit may be shared by neighbors within a zone of local heat capture. Metabolic heat as a shareable public good raises interesting questions about conflict and cooperation of heat production and capture. Metabolic heat may also be deployed as a weapon. Species with greater thermotolerance gain by raising local temperature to outcompete less thermotolerant taxa. Metabolic heat may provide defense against bacteriophage attack, by analogy with fever in vertebrates. This article outlines the theory of metabolic heat in microbial conflict and cooperation, presenting several predictions for future study.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

This article is a study on the (k,s)-Riemann-Liouville fractional integral, a generalization of the Riemann-Liouville fractional integral. Firstly, we introduce several properties of the extended integral of continuous functions. Furthermore, we make the estimation of the Box dimension of the graph of continuous functions after the extended integral. It presents that the upper Box dimension of the (k,s)-Riemann-Liouville fractional integral for any continuous functions is no more than the upper Box dimension of the functions on the unit interval I=[0,1], which indicates that the upper Box dimension of the integrand f(x) will not be increased by the σ-order (k,s)-Riemann-Liouville fractional integral ksD−σf(x) where σ&gt;0 on I. Additionally, we prove that the fractal dimension of ksD−σf(x) of one-dimensional continuous functions f(x) is still one.

The fractal dimension of geomagnetic variations at the Baigazan magnetic station at Russian Altay for 2011-2013 was calculated using the Higuchi method. The daily variation of Higuchi Fractal Dimension (HFD) for the D,H,Z-components of the geomagnetic field has been investigated, its contribution to the variability of HFD is from 30 to 40 percent of the total variance. A correlation analysis of the fractal dimension of the variations of the D,H,Z-components with Auroral Electrojet (AE) index and solar wind characteristics was carried out. A negative correlations with logarithms of AE-index, interplanetary magnetic field (IMF) strength and solar wind velocity were found. About 25 percent of the fractal dimension variance is controlled by the variability of these characteristics. Pair and partial correlation coefficients for these parameters were calculated for every month of 2011-2013.

Motivated by the well-known contradiction of special relativity and the heat equation, a wave equation for temperature scalar field is presented that also resolves the old controversy of (Lorentz) transformation of temperature and entropy. After showing that the current dogma of temperature and entropy being emergent concepts is based on but a logical fallacy, it is proposed that single particles posses entropy. This principle of fundamentality of entropy is then shown to be compatible with the equipartition theorem by yielding corrections in the quantum gravity regime.

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

The combined heat and power system is based on the principle of "cascade utilization of thermal energy" for system integration and optimization. The rational utilization of energy, as well as the rational arrangement of energy flow and the process optimization combination of the overall system are taken into account in order to achieve multifunctional goals in the field of thermal engineering. The present paper presents a detailed assessment of combined heat and power systems from above standpoints. This article is divided into two parts “CHP based on thermo-dynamic cycles” and “CHP based on non-thermodynamic cycles”. Each part is then classified based on power subsystem energy consumption efficiency (high or low), including Rankine cycle, ORC, Stirling cycle, gas turbine, reciprocating engine, PVT and fuel cell. The present paper also helps identify the research gaps in this area and provides direction on future studies on combined heat and power systems.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

Purpose: To simplify the application of optical coherence tomography (OCT) for examination of subsurface morphology in the oral cavity and reduce barriers towards adoption of OCT as a biopsy guidance device. The aim of this work was to develop automated software tools for simplified analysis of the large volume of data collected during OCT. Methods: Imaging and corresponding histopathology were acquired in-clinic using a wide-field endoscopic OCT system. An annotated dataset (n = 294 images) from 60 patients (34 male, 26 female) was assembled to train four unique neural networks. A deep learning pipeline was built using convolutional and modified u-net models to detect the imaging field of view (network 1), detect artifacts (network 2), identify the tissue surface (network 3), and identify the presence and location of the basement membrane (network 4). Results: The area under the curve of the image and artifact detection networks was 1.00 and 0.94 respectively. The Dice similarity score for the surface and basement membrane segmentation networks was 0.98 and 0.83 respectively. Conclusion: Deep Learning (DL) techniques can identify the location and variations in the epithelial surface and basement membrane in OCT images of the oral mucosa. Segmentation results can be synthesized into accessible en face maps to allow easier visualization of changes.

My innovative entropy measure, Ismail entropy, namely, (IE) is an ultimate generalization to numerous generalized entropies within the literature. The fractal dimension of IE is identified in this paper. On another applicative note, this paper offers some potential applications of fractal dimension to smart cities. The paper ends with closing remarks combined with some challenging open problems and the next phase of research.

UNESCO highlights socio-emotional, cognitive, and behavioral learning as critical for advancing sustainability. As major events, sports generate significant social, economic, and environmental impacts. This study analyzed how academic background, gender, age, sport type, and modality influenced elite Colombian Olympic and Paralympic athletes' socio-emotional competencies. Methods: Colombian elite athletes who were members of the “Support to the Excellence Coldeportes Athlete” participated in the study. The total population studied included 334 Colombian elite athletes: mean age 27.10 ± 6.57 years old with 13.66 ± 6.37 years practicing his/her sports modality. The socio-emotional competencies of the participants were assessed using the Socio-emotional Competencies Scale (SECS). Results: Men scored higher in interpersonal regulation, self-awareness, conflict resolution, and emotional regulation. Younger athletes (≤25 years) had higher self-consciousness. Individual versus team sports did not differ. Paralympians showed higher motivation, self-awareness, teamwork, and emotional regulation. University educated athletes scored higher in motivation, self-awareness, teamwork, and empathy. All competencies positively correlated. Conclusion: Individualized interventions targeting improved socio-emotional performance are vital for sustainability and should account for differences across gender, age, education, and disability status.

Metformin (MeT) is an FDA-approved drug with a myriad of health benefits. Besides being used as an anti-diabetic drug, MeT is also effective against various cancers, liver-, cardiovascular-, and renal diseases. It has also been proven to demonstrate anti-ageing and neuroprotective effects. This study was undertaken to examine its unique potential as an anti-virulence drug against an opportunistic bacterial pathogen, Pseudomonas aeruginosa. Due to the menace of multidrug resistance in pathogenic microorganisms, many novel or repurposed drugs with anti-virulence prospects are emerging as next-generation therapies with the aim to overshadow the application of existing antimicrobial regimens. The quorum sensing (QS) mechanisms of P. aeruginosa are an attractive drug target for attenuating bacterial virulence. In this context, the anti-QS potential of MeT was scrutinized using biosensor assays. MeT was comprehensively evaluated for its effects on different motility phenotypes, virulence factor production (phenotypic and genotypic expression) along with biofilm development in P. aeruginosa in vitro. At sub-lethal concentrations, MeT displayed prolific quorum quenching (QQ) ability and remarkably inhibited AHL biosynthesis in P. aeruginosa. Moreover, MeT (1/8 MIC) effectively downregulated the expression levels of various QS- and virulence genes in P. aeruginosa, which coincided with a notable reduction in the levels of alginate, hemolysin, pyocyanin, pyochelin, elastase, and protease production. In silico analysis through molecular docking also predicted strong associations between the QS receptors of P. aeruginosa and MeT. MeT also compromised the motility phenotypes and successfully abrogated biofilm formation by inhibiting EPS production in P. aeruginosa. Hence, the QQ, anti-virulence, and anti-fouling potential of MeT was elucidated for the first time against P. aeruginosa.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

In this article, we are interested in a new generic class of nonlocal fractional impulsive differential inclusions with linear sectorial operator and Lipschitz multivalued function in the setting of finite dimensional Banach spaces. By modifying the definition of PC-mild solutions initiated by Shu, we succeeded to determine new conditions that sufficiently guarantee the existence of the solutions. The results are obtained by combining techniques of fractional calculus and fixed point theorem for contraction maps. We also characterize the topological structure of the set of solutions. Finally, we provide a demonstration to address the applicability of the theoretical results.

The objective of the study was to examine the effects of perceived stress on depression and subsequently to examine the effects of depression on alcohol use disorders. The data were obtained by an electronic questionnaire survey during the coronavirus disease 2019 (COVID-19) pandemic (n=1523 Slovak college students). Descriptive, regression and correlation analysis were used in the analytical processing, while the analyses included students' scores in three diagnostic tools (Perceived Stress Scale (PSS), Patient Health Questionnaire for depression (PHQ 9) and Alcohol Use Disorders Identification Test (AUDIT)), as well as gender and income characteristics. The PSS identified an increased level of perceived stress in female students, in contrast, the AUDIT showed an increased level of alcohol use disorders in male students. Differences in mental and behavioural disorders between the gender and income categories were significant in most of the analysed cases. In terms of gender-income characteristics, it was possible to confirm a significant positive effect of the PSS score on the PHQ 9 score, as well as a significant positive effect of the PHQ 9 score on the AUDIT score. As a result, efforts to reduce stress will be reflected in a reduction of depressive disorders as well as a reduction of excessive alcohol consumption among students.

Geothermal energy is likely to be a significant contributor in achieving sustainable energy goals and net-zero emissions targets. Within geothermal power plants, heat exchangers play a critical role in harnessing this renewable energy source. However, these heat exchangers encounter significant challenges when exposed to geothermal fluids, including erosion, corrosion, and scaling, which adversely affects their performance and longevity. The current review focuses on surface engineering techniques, particularly coatings, as a highly effective and economically viable solution to address these challenges in geothermal heat exchangers. The review begins by providing an overview of geothermal energy, its significance in the context of sustainability and the important role played by heat exchangers in geothermal power generation, followed by the challenges and their impact on heat exchangers. The subsequent section focuses on surface engineering by coatings and its types employed to enhance the performance of heat exchangers. In the final part, the reader is presented with an overview of the challenges associated with the application of coatings in geothermal heat exchangers and potential future directions in this field. This review offers a detailed understanding of the critical role coatings play in improving the efficiency and service life of heat exchangers in geothermal power plants.

Water stress (WS) and heat stress (HS) have a negative effect on soybean plant growth and crop productivity. During WS, soybean plants opt for survival through ion homeostasis and the conformations of proteins are disconcerted as plant cells lose water while HS leads to difficulties in flowering and fruiting. Some of these changes include oxidative stress leading to the destruction of photosynthetic apparatus, macromolecules within cells and the onset of complex signaling cascades. Changes in the physiological characteristics, proteome, and certain metabolites investigated on molecular and cellular functions were studied in two soybean cultivars exposed to different heat and water stress conditions independently and in combination. Leaf protein composition was studied using 2-DE and complemented with MALDI TOF mass spectrometry. While two cultivars displayed genetic variation in response to water and heat stress, thirty-nine proteins were significantly altered in their relative abundance in response to WS, HS and combined WS+HS in both cultivars; a majority of them involved in metabolism, response to heat and photosynthesis showing significant cross-tolerance mechanisms. Functional analysis revealing a majority of heat responsive-proteins were more abundant during HS and combined stress (WS+HS) whereas these proteins were low to WS in cultivar PI 471938 and heat shock proteins were in low abundance to water, heat and combined stresses in cultivar R95-1705. Most protein abundances were not correlated with their expression at mRNA levels in PI cultivar, however, in cultivar R 95, the expression levels of transcript follow their relative abundance in proteins. Our systems bioinformatics analyses revealed that MED37C, a probable mediator of RNA polymerase transcription II protein showed potential interacting partners in Arabidopsis and our studies signifies the marked impact of this protein in PI cultivar. Elevated activities in antioxidant enzymes indicate that the PI-371938 cultivar has the ability to restore the oxidation levels and sustain the plant during the stress. Our study hypothesizes the plant’s development of cross-stress tolerance which will help foster the ongoing ventures in genetic modifications in stress tolerance.

Starting from the fact that one of the global control strategies of the Permanent Magnet Synchronous Motor (PMSM), namely the Direct Torque Control (DTC) type control strategy, is characterised by the fact that the inner flux and torque control loop usually uses hysteresis ON-OFF type controllers and the oscillations introduced by them have to be cancelled out by the outer speed loop controller (which is usually a PI speed controller and whose performance is good around the global operating points and for relatively small variations of the external parameters and disturbances caused in particular by the load torque variation), while retaining the advantages of the DTC strategy, this paper presents the improvement of the performance of the PMSM sensorless control system using Proportional Integrator (PI), PI Equilibrium Optimizer Algorithm (EOA), Fractional Order (FO) PI, Tilt Integral Derivative (TID) and FO Lead-Lag for constant flux, and Sliding Mode Control (SMC) and FOSMC for variable flux. The performance indicators of the control system are the usual ones: response time, settling time, overshoot, steady-state error and speed ripple, plus another one given by the fractal dimension (FD) of the PMSM rotor speed signal, and the hypothesis that the FD of the controlled signal is higher when the control system provides better performance is verified. The paper also presents the basic equations of the PMSM, based on which the synthesis of integer and fractional controllers, the synthesis of an observer for estimating the PMSM rotor speed, electromagnetic torque and stator flux are presented. The comparison of the performance of the proposed control systems and the demonstration of the parametric robustness are performed by numerical simulations in Matlab/Simulink using Simscape Electrical and Fractional Order Modelling and Control (FOMCON). Real-time control based on an embedded system using a TMS320F28379D controller demonstrates the good performance of the PMSM sensorless control system based on the DTC strategy in a complete hardware-in-the-loop (HIL) implementation.

Hay and straw are commonly used materials in agriculture. They are organic materials and therefore flammable. This article examines the behaviour of hay and straw when exposed to radiant heat. The objective of this study is to experimentally determine the ignition temperature of hay and straw under the influence of radiant heat. The research investigates the effects of sample type (hay and straw) and sample quantity on the thermal degradation process, temperature increase within the samples, and ignition temperature of the samples as a function of time. The ignition temperature of hay was determined to be higher (407°C) compared to straw (380°C). The results did not demonstrate a significant correlation between sample type and the thermal degradation process or the ignition temperature of hay and straw.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

There is a lack of knowledge concerning the effects of ambient heat exposure on morbidity in Northern Europe. Therefore, this study aimed to evaluate the relationships of daily summer-time temperature and heatwaves with cardiorespiratory hospital admissions in the Helsinki metropolitan area, Finland. Methods: Time-series models adjusted for potential confounders such as air pollution were used to investigate the associations of daily temperature and heatwaves with cause-specific cardiorespiratory hospital admissions, during summer months of 2001-2017. Daily number of hospitalizations was obtained from the national hospital discharge register, weather information from the Finnish Meteorological Institute. Results: Increased daily temperature was associated with decreased risk of total respiratory hospital admissions and asthma. Heatwave days were associated with 20.5% (95% CI: 6.9, 35.9) increased risk of pneumonia admissions and during long or intense heatwaves also with total respiratory admissions in the oldest age group (≥ 75 years). There were also suggestive positive associations between heatwave days and admissions due to myocardial infarction and cerebrovascular diseases. In contrast, risk of arrhythmia admissions was decreased 20.8% (95% CI: 8.0, 31.8) during heatwaves. Conclusions: Heatwaves, rather than single hot days, are a health threat affecting the morbidity even in a Northern climate.

As a new kind of highly compact and efficient micro-channel heat exchanger, printed circuit heat exchanger (PCHE) is a promising candidate satisfying the heat exchange requirements of liquefied natural gas (LNG) vaporization at low and high pressure. The effects of airfoil fin arrangement on heat transfer an flow resistance were numerically investigated using supercritical liquefied natural gas (LNG) as a working fluid. The thermal properties of supercritical LNG were tested by utilizing a REFPROF software database. Numerical simulation was performed using FLUENT. The inlet temperature of supercritical LNG was 121 K,and its pressure was 10.5MPa. The reference mass flow rate of LNG was set 1.22 g/s for the vertical pitch L_v = 1.67 mm and the staggered pitch L_s = 0 mm, with the Reynolds number of about 3750. The SST k-ω model with enhanced wall treatment was selected by comparing with the experimental data. The airfoil fin PCHE had better thermal-hydraulic performance than that of the straight channel PCHE. Moreover, the airfoil fins with staggered arrangement displayed better thermal performance than that of the fins with parallel arrangement. The thermal-hydraulic performance of airfoil fin PCHE was improved with increasing L_s and L_v. Moreover, L_v affected on the Nusselt number and pressure drop of airfoil fin PCHE more obviously. In conclusion, a sparser staggered arrangement of fins showed a better thermal-hydraulic performance in airfoil fin PCHE.

To verify the reliability of the proposed stitching linear scan method for roundness measurement of small cylindrical workpieces, measurement uncertainties of the workpieces with various dimension are conducted. The cross-sectional circle of a cylindrical workpiece is divided into several equal arcs to be measured. Thus, the arc profile can be characterized according to the measured arcs. The roundness profile of the cylindrical part can be obtained by stitching these arc profiles together. Firstly, the measurement uncertainty of the workpiece with a diameter 1.5 mm and length 5.8 mm is evaluated to be 0.095 μm which can meet the uncertainty target of 0.1 μm. Considering the uncertainty of θx and θz which are the alignment around X-axis and Z-axis respectively changing with workpiece dimension changing, relevant uncertainties are carried out. As a result, there is no limitation with respect to workpiece diameter theoretically If the alignment can reach θz = θx = ±0.1° without considering the measurable range of the machine.

With simple but rigorous arguments we prove that the ordinary second quantization of bosonic and fermionc fields is formally equivalent to constraining the elementary degrees of freedom of the classical fields to have intrinsically periodic dynamics in time. This result confirms and extends the formal equivalence obtained in previous papers for general Hamiltonian systems in terms of canonical quantization, for elementary relativistic particles also in terms of the Feynman Path Integrals, as well as other remarkable correspondences of both phenomenological and theoretical fundamental interest.

The Japanese Association for Acute Medicine Committee recently proposed a novel classification system for the severity of heat-related illnesses. The illnesses are simply classified into three stages based on symptoms and management or treatment. Stages I, II, and III broadly correspond to heat cramp and syncope, heat exhaustion, and heat stroke, respectively. Our objective was to examine whether this novel severity classification is useful in the diagnosis by healthcare professionals of patients with severe heat-related illness and organ failure. A nationwide surveillance study of heat-related illnesses was conducted between June 1 and September 30, 2012, at emergency departments in Japan. Among the 2130 patients who attended 102 emergency departments, the severity of their heat-related illness was recorded for 1799 patients, who were included in this study. In the patients with heat cramp and syncope or heat exhaustion (but not heat stroke), the blood test data (alanine aminotransferase, creatinine, blood urea nitrogen, and platelet counts) for those classified as stage III were significantly higher than those of patients classified as stage I or II. There were no deaths among the patients classified as stage I. This novel classification may avoid underestimating the severity of heat-related illness.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

We study the work fluctuations in ergotropic heat engines, namely two-strokes quantum Otto engines where the work stroke is designed to extract the ergotropy (the maximum amount of work by a cyclic unitary evolution) from a couple of quantum systems at canonical equilibrium at two different temperatures, whereas the heat stroke thermalizes back the systems to their respective reservoirs. We provide an exaustive study for the case of two qutrits whose energy levels are equally spaced at two different frequencies by deriving the complete work statistics. By varying the values of temperatures and frequencies, only three kinds of optimal unitary strokes are found: the swap operator U1, an idle swap U2 (where one of the qutrits is regarded as an effective qubit), and a non trivial permutation of energy eigenstates U3, which indeed corresponds to the composition of the two previous unitaries, namely U3 = U2U1. While U1 and U2 are Hermitian (and hence involutions), U3 is not. This point has an impact on the thermodynamic uncertainty relations (TURs) which bound the signal-to-noise ratio of the extracted work in terms of the entropy production. In fact, we show that all TURs derived from a strong detailed fluctuation theorem are violated by the transformation U3.

In this paper, we design a quantum heat exchanger which converts heat into light on relatively short quantum optical time scales. Our scheme takes advantage of collective cavity-mediated laser cooling of an atomic gas inside a cavitating bubble. Laser cooling routinely transfers individually trapped ions to nano-Kelvin temperatures for applications in quantum technology. The quantum heat exchanger which we propose here is expected to provide cooling rates of the order of Kelvin temperatures per millisecond and is expected to find applications in micro and nanotechnology.

Drying food involves complex physical atmospheric mechanisms with non-linear relations from the air-food interactions and those relations are strongly dependent on the moisture contents and the type of food. Such dependence makes it complex to design suitable dryers dedicated to a single drying process. To streamline the design of a novel compact food-drying machine, a heat pump dryer component design optimization algorithm was developed as a subprogram of a Computer Aided Engineering tool. The algorithm requires inputting food and air properties, the volume of the drying container and the technical specifications of the heat-pump off-the shelf components. The heat required to dehumidify the food supplied by the heat exchange process from condenser to evaporator, and the compressor’s requirements (refrigerant mass flow rate and operating pressures) are then calculated. Compressors can then be selected based in the volume and type of food to be dried. The algorithm is shown via a flow chart to guide the user through 3 different stages: Changes in drying air properties, Heat flow within dryer and Product moisture content. Example results of how different compressors are selected for different type of produces and quantities (Agaricus Blazei mushroom with 3 different moisture contents or fish from Thunnini tribe) conclude this article.

Ocean surface heat fluxes play a significant role in the genesis and evolution of various marine-based atmospheric phenomena, from the synoptic scale down to the microscale. While in-situ measurements from buoys and flux towers will continue to be the standard in regards to surface heat flux estimates, they commonly have significant gaps in temporal and spatial coverage. Previous and current satellite missions have filled these gaps; though they may not observe the fluxes directly, they can measure the variables needed (wind speed, temperature, and humidity) to estimate latent and sensible heat fluxes. However, current remote sensing instruments have their own limitations, such as infrequent coverage, signals attenuated by precipitation, or both. The Cyclone Global Navigation Satellite System (CYGNSS) mission overcomes these limitations over the tropical and subtropical oceans by providing improved coverage in nearly all weather conditions. While CYGNSS (Level 2) primarily estimates surface winds, when coupled with observations or estimates of temperature and humidity from reanalysis data, it can provide estimates of latent and sensible heat fluxes along its orbit. This paper describes the development of the Surface Heat Flux Product for the CYGNSS mission, its current results, and expected improvements and changes in future releases.

Space and water heating for residential and commercial buildings amount to a third of the European Union’s total final energy consumption. Approximately 75% of the primary energy is still produced by burning fossil fuels, leading to high greenhouse gas emissions in the heating sector. Therefore, policymakers increasingly strive to trigger investments in sustainable and low-emission heating systems. This study forms part of the “Roll-out of Deep Geothermal Energy in North-West-Europe”-project and aims at quantifying the spatial heat demand distribution in the Interreg North-West-Europe region. An open-source geographic information system and selected Python packages for advanced geospatial processing, analysis, and visualization are utilized to constrain the maps. These were combined, streamlined, and optimized within the open-source Python package PyHeatDemand. Based on national and regional heat demand input data, three maps are developed to better constrain heat demand at a high spatial resolution of 100*100m2 for the residential and commercial sectors, and for both together (in total). The developed methodology cannot only be applied to transnational heat demand mapping but also on various scales ranging from city district level to states and countries. In addition, the workflow is highly flexible working with raster data, vector data, and tabular data. Results reveal a total heat demand of the Interreg North-West-Europe region of about 1,700TWh. The spatial distribution of the heat demand follows specific patterns, where heat demand peaks are usually in metropolitan regions like for the city of Paris (1,400MWh/ha), the city of Brussels (1,300MWh/ha), the London metropolitan area (520 MWh/ha), and the Rhine-Ruhr region (500 MWh/ha). The developed maps are compared with two international projects, Hotmaps and Heat Roadmap Europe’s Pan European Thermal Atlas. The average total heat demand difference from values obtained in this study to Hotmaps and Heat Roadmap Europe is 24 MWh/ha and 84 MWh/ha, respectively. It is assumed that the implementation of real consumption data is an improvement in spatial predictability. The heat demand maps are therefore predestined to provide a conceptual first overview for decision-makers and market investors. The developed methods will further allow for anticipated mandatory municipal heat demand analyses.