We present a new post-processing method for Quantum Key Distribution (QKD) that raise cubically the secret key rate in the number of double matching detection events. In Shannon’s communication model information is prepared at Alice’s side then it is intended to pass it over a noisy channel. In our approach, secret bits do not rely in Alice’s transmitted quantum bits but in Bob’s basis measurement choices. Therefore measured bits are publicly revealed while bases selections remain secret. Our method implements sifting, reconciliation and amplification in a unique process, it just require a round iteration, no redundancy bits are sent and there is no limit in the correctable error percentage. Moreover, this method can be implemented as a post processing software into QKD technologies already in use.

True contact between solids with randomly rough surfaces tends to occur at a large number of microscopic contact patches. So far, two scaling regimes have been identified for the number density n(A) of contact-patch sizes A in elastic, non-adhesive, self-affine contacts. At small A, n(A) is approximately constant, while n(A) decreases as a power law at large A. Using Green’s function molecular dynamics, we identify a characteristic (maximum) contact area Ac above which a superexponential decay of n(A) becomes apparent if the contact pressure is below the pressure p_cp at which contact percolates. We also find that A_c increases with load relatively slowly far away from contact percolation. Results for A_c can be estimated from the stress autocorrelation function G_σσ (r) with the following argument: the radius of characteristic contact patches, r_c, cannot be so large that G_σσ (r_c) is much less than p_c². Our findings provide a possible mechanism for the breakdown of the proportionality between friction and wear with load at large contact pressures and/or for surfaces with a large roll-off wavelength.

Plant leaf area index (LAI) is a key characteristic affecting field canopy microclimate. In addition to traditional professional measuring instruments, smartphone camera sensors have been used to measure plant LAI. However, when smartphone methods were used to measure conifer forest LAI, very different performances were obtained depending on whether the smartphone was held at the zenith angle or at a 57.5° angle. To validate further the potential of smartphone sensors for measuring conifer LAI and to find the limits of this method, this paper reports the results of a comparison of two smartphone methods with an LAI-2000 instrument. It is shown that both methods can be used to reveal the conifer leaf-growing trajectory. However, the method with the phone oriented vertically upwards always produced better consistency in magnitude with LAI-2000. The bias of the LAI between the smartphone method and the LAI-2000 instrument was explained with regard to four aspects that can affect LAI: gap fraction, leaf projection ratio, sensor field of view (FOV), and viewing zenith angle (VZA). It was concluded that large FOV and large VZA cause the 57.5° method to overestimate the gap fraction and hence underestimate conifer LAI, especially when tree height is greater than 2.0 m. For the vertically upward method, the bias caused by the overestimated gap fraction is compensated for by an underestimated leaf projection ratio.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

The interest in virtual fencing, as opposed to traditional physical barriers, has increased since it makes it easier to move the boundaries of animal enclosures for agricultural and rewilding purposes. Despite this, the implementation of virtual fence systems, such as the Nofence© system, requires large financial investments. The necessity of individual collars also makes it more difficult to implement this system on a larger scale. If a herd of cattle tend to maintain cohesive social groups around dominant individuals, it might be possible to use fewer collars thereby making the system more cost efficient. This study investigates the pattern in spatial distribution in a herd of 17 Angus cows on Fanø in Denmark with GPS locations, using a Nofence© system. The aim of this paper is to determine how individuals position themselves in a herd, spatially, and identify a pattern in ranks. The method used in this study examines the distances between an individual to the rest of the herd mates using nearest neighbour and distribution plots. Contrary to the expectations, this study did not show a distinct pattern in herd distribution. While some tendencies in spatial distribution patterns were observed, only a low concordance could be found (W=0.15,p=3.02e−16). Therefore, interactions among individuals should be considered in future studies, rather than only investigating the herd as one unit. A cumulative curves of the ranks estimated over the entire periods allowed however a rough estimation of the hierarchy and allowed the identification of the highest ranked cows. Therefore it might be possible to use fewer collars if the high ranked cows are discovered, but the estimation of the hierarchy will require a period of observation overall several days as the hierarchical positions are fluctuating too much from days to days. Therefore the cumulative rank curves seems to be a valid solution.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

This paper shows that by applying the Nyquist-Shannon sampling theorem, the spatial and temporal resolution of a simulation can be no more than half the resolution of the simulating reality. This has significant implications for not only the values of the observables in the simulation but also its physical laws. This progressive halving of nested simulations coupled with the minimum resolution compatible with the production of a simulation also sets a limit to the nestedness of a lineage of simulations (it is by no means infinite). The limit of nestedness is then used to calculate the probability that we are living in a simulation assuming a single base reality. This will be shown to be significantly lower than popular expectation. A Kardashev-like scale, with three variants, is also developed to gauge the technological advancement of a civilization in relation to the extent to which it can extract information from space and time.

This article theoretically derives the magnetic field and vector potential produced by a steady current I flowing in an arbitrary plane loop at an arbitrary point r. Numerical examples are presented to demonstrate the behavior of the magnetic field produced by loops of various shapes such as polygons, circles, ellipses, and p-norm balls. Taking the limit as the loop shrinks to a point and the current I grows to infinity so that the magnetic dipole moment m of the loop (defined as the current I times the vector area of the loop) is kept constant, the magnetic field and vector potential are theoretically shown to converge to those of an ideal point magnetic dipole m.

Motivated by empirical observations, we propose a possible extension of Gibrat's law. By applying it into the random growth theory of income distribution (Gabaix, 2009), we find that the income distribution is described by a generalized Pareto-type distribution (GPD) with three parameters. We observe that there is a parameter /elta in the GPD that plays a key role in determining the shape of income distribution. By using the Kolmogorov-Smirnov test, we empirically show that, for typical market-economy countries, /elta is close to 0 significantly, such that the income distribution is characterized by a two-class pattern in which the bottom 90% of the population is approximated by an exponential distribution and the richest 1%~3% is approximated by an asymptotic power law. However, we empirically find that, for China both in planned economy period and in early stages of market reformation (from 1978 to 1990), /elta is significantly deviated from 0, such that the bottom of the population no longer conforms to an exponential distribution.

Recent developments, begun by the ascending spiral of the anticipated endless prospects of ChatGPT, promote artificial intelligence (AI) as an indispensable tool and commodity whose time has come. Yet the sinister specter of a technology that has hidden and unmanageable attributes that might be harmful to society looms in the background. As well as the likelihood that it will never deliver on the purported promise of artificial general intelligence (AGI). Currently the prospects for the development of AI and AGI are more a matter of opinion than based on a consistent methodological approach. Thus the need to take a step back to develop a general framework from which to evaluate current AI efforts, which also permits the determination of the limits to its future prospects as AGI. To gain insight into the development of a general framework, a key question that needs resolution is, what is the connection between human intelligence and machine intelligence? This is the question that needs a response because humans are at the center of AI creation and realize that without an understanding of how we become what we become, we have no chance of finding a solution. This work proposes infoautopoiesis, the self-referential, recursive and interactive process of self-production of information, as the needed general framework. Infoautopoiesis shows how the key ingredient of information is fundamental to an insightful resolution to this crucial question and allows predictions as to the present and future of AGI.

Under optimal conditions, just 3–6 ms of visual stimulation suffices for humans to see motion. Motion perception on this time scale implies that the visual system under these conditions reliably encodes, transmits, and processes neural signals with near-millisecond precision. Motivated by in vitro evidence for high temporal precision of motion signals in the primate retina, we investigated how neuronal and perceptual limits of motion encoding relate. Specifically, we examined the correspondence between the time scale at which cat retinal ganglion cells in vivo represent motion information and temporal thresholds for human motion discrimination. The time scale for motion encoding by ganglion cells ranged from 4.6–91 ms, depended nonlinearly on temporal frequency but not on contrast. Human psychophysics revealed that minimal stimulus durations required for perceiving motion direction were similarly brief, 5.6–65 ms, similarly depended on temporal frequency but, above ~10%, not on contrast. Notably, physiological and psychophysical measurements corresponded closely throughout (r = 0.99), despite more than a 20-fold variation in both human thresholds and optimal time scales for motion encoding in the retina. These results demonstrate that neural circuits for motion vision in cortex can maintain and make use of the high temporal fidelity of the retinal output signals.

1) We shall discuss what modern interpretations say about the Heisenberg's uncertainties. These interpretations explain that a quantity begins to 'lose' meaning when a conjugate property begins to 'acquire' definite meaning. We know that a quantity losing meaning means that it has no fixed value and has an uncertainty . In this paper we look deeper into this interpretation and the outcome reveals more evidence of the quantity losing meaning. Newer insights appear. 2) We consider two extreme cases of hypothetical processes nature undergoes, without interference by a measurement: One, a system collapses to an energy eigenstate under the influence of a Hamiltonian instantaneously at a time $t$. This is thus what would happen if we would measure the system's energy. Next, when a particle becomes localised to a point at a time $t_0$ under the influence of a Hamiltonian. This is thus what would happen if we would measure the system's position. We shall prove that both these situations cannot arise under ordinary circumstances and thus measurement processes cannot be modelled by physical Hamiltonians.

An increasing amount of electric energy is consumed by computers as they progress in function and capabilities. All of it is dissipated in heat during the computing and communicating operations and we reached the point that further developments are hindered by the unbearable amount of heat produced. In this paper we briefly review the fundamental limits in energy dissipation, as imposed by the laws of physics, with specific reference to computing and memory storage activities.

Background: Non-alcoholic fatty liver disease (NAFLD) is manifested by hepatic steatosis, insulin resistance, hepatocyte death, and systemic inflammation. Obesity induces steatosis and chronic inflammation in the liver. However, the precise mechanism underlying hepatic steatosis in the setting of obesity remains unclear. Here we report studies that address this question. Methods: 14 weeks on high-fat diet (HFD) with high sucrose, C57BL/6 mice revealed a phenotype of liver steatosis. Transcriptional profiling analysis of the liver tissues was performed using RNA sequencing (RNA-seq). Results: Our RNA-seq data revealed 692 differentially expressed genes involved in processes of lipid metabolism, oxidative stress, immune responses, and cell proliferation. Notably, the gene encoding neutral sphingomyelinase SMPD3, was predominantly upregulated in the liver tissues of the mice displaying a phenotype of steatosis. Moreover, nSMase2 activity was elevated in these tissues of the liver. Pharmacological and genetic inhibition of nSMase2 prevented intracellular lipid accumulation and TNFα-induced inflammation in in-vitro HepG2-steatosis cellular model. Furthermore, nSMase2 inhibition ameliorates oxidative damage by rescuing PPARα and prevent cell death associated with high glucose/oleic acid-induced fat accumulation in HepG2 cells. Conclusions: Collectively, our findings highlight the prominent role of nSMase2 in hepatic steatosis which could serve as a potential therapeutic target for NAFLD and other hepatic steatosis-linked disorders.

In order to investigate the size distributions and seasonal variations of carbonaceous aerosols (OC and EC), the carbonaceous species were collected and then analyzed by using a 9-stage Anderson-type aerosol sampler and DRI Model 2001A Thermal/Optical Carbon Analyzer on the typical industrial city Nanjing in Yangtze River Delta, China in the summer, autumn and winter of 2013 and spring of 2014. OC, EC, SOC and POC exhibited obvious seasonal variations, with the highest level in winter (39.1±14.0, 5.7±2.1, 23.6±11.7 and 14.1±5.7 μg•m^-3) and the lowest level in summer (20.6±6.7, 3.3±2.0, 12.2±3.8 and 8.4±4.1 μg•m^-3), and were mainly centralized in PM_1.1 in four seasons. The concentrations of OC in PM_1.1 varied in the order of winter > autumn > spring > summer, while EC ranked in the order of autumn > winter > summer > spring. In the PM_1.1-2.1 and PM_2.1-10, the concentrations of OC and EC decreased in the sequence of winter > spring > autumn > summer. The size spectra of OC, EC and SOC had bimodal distributions in four seasons, except for EC with four peaks in summer. The size spectra of POC varied greatly with seasons, exhibiting bimodal distribution in winter, trimodal distribution in spring and summer, and four peaks in autumn. The OC/EC ratios were 7.0, 6.3, 7.6 and 6.9 in spring, summer, autumn and winter, respectively, which demonstrated the abundance of secondary organic aerosols in Nanjing. The sources of carbonaceous aerosol varied significantly with seasons, and were dominated by vehicle exhaust, coal and biomass burning in PM_2.1, and dominant by dust, coal and biomass burning in PM_2.1-10.

Abstract: Global ecological concern regarding the transfer of fouling organisms to ship hulls is increasing. This study investigated the species composition, dominant species, distribution patterns, community structure, and life-cycle differences of hull-fouling macroinvertebrates on five research vessels (R/Vs: Isabu, Onnuri, Eardo, Jangmok 1, and Jangmok 2) operated by the Korea Institute of Ocean Science and Technology (KIOST). Hull-fouling macroinvertebrates were collected three to five times on quadrats from the upper and middle sectors of the hull sides, bottom, and niche areas (the propellers and shafts and the thrusters). A total of 47 macroinvertebrate species were identified, represented by 8,519 individuals(ind.)/m2 and a biomass of 1,967 gWWt/m2 on the five vessels. The number of species, density, and biomass were greater on the coastal vessels the Eardo, Jangmok 1, and Jangmok 2 than on the ocean-going vessels the Isabu and Onnuri. Among the coastal vessels, barnacles were the most abundant and had the greatest density, while mollusks had the highest biomass. Differences between hull sectors showed that the highest species abundance and density appeared on all hulls in ports and bays where the Jangmok 1 operated, while the highest species abundance, density, and biomass were identified in the niche areas of the Eardo, which operated farther from the coast. The hull-fouling macroinvertebrates that exceeded 1% of all organisms were the barnacles Amphibalanus amphitrite, Balanus trigonus, and Amphibalanus improvisus; the polychaete Hydroides ezoensis; the bivalves Magallana gigas and Mytilus galloprovincialis; and the amphipod Jassa slatteryi. The dominant species were cosmopolitan and globally distributed, and many of them were cryptogenic. Six native species were identified: M. gigas, H. ezoensis, the amphipod Melita koreana, the isopod Cirolana ko-reana, and the barnacle B. trigonus and F. kondakovi. Eight non-indigenous species (NIS) were de-tected: barnacles A. amphitrite and A. improvisus, the bivalve M. galloprovincialis, the polychaete Perinereis nuntia, amphipods J. slatteryi and Caprella californica, and bryozoans Bugulina californica and Bugula neritina. Of the fouling macroinvertebrates found on the vessel hulls, 13% were native and 17% were NIS. The nMDS ordination analysis of the five vessels showed four clusters of fouling macroinvertebrate communities: two ocean clusters (the Isabu and Onnuri), one coastal cluster (the Eardo and Jangmok 2), and one local cluster (the Jangmok 1). More diverse communities developed on the hulls of vessels that operated locally rather than globally or in deep oceans. Spearman rank correlation showed that biological indices such as number of species, density, and biomass correlated highly and positively with the numbers of days on coastal operations and negatively with the number days on ocean operations. The species diversity index correlated positively with the total number of anchoring days and coastal operation days and negatively with the total number of operation days and ocean operation days. The macroinvertebrates differed by the area of operation, the port of anchorage, the number of days in operation and at anchor, and the hull sectors. There is no previous research data on hull-fouling macroinvertebrates in the Republic of Korea, and this study provides a basis for future studies to identify introduced species and their differences based on operation area.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Taxonomic studies of dreams that continue to influence the dreamer’s thoughts and feelings after awakening have distinguished three types of impactful dreams: nightmares, existential dreams, and transcendent dreams. Of these, existential dreams and transcendent dreams are characterized by recurrent metacognitive appraisal of the epistemic tension between complementary (a) metaphoric (A “is” B) assertions and (b) literal (A “is not” B) assertions. Metacognitive appraisal of such complementary metaphoric and literal assertions is detectible as the felt sense of inexpressible realizations. The poesy of such inexpressible realizations depends upon the juxtaposition of a metaphoric topic and vehicle that are both “semantically dense” but at an abstract level “distant” from each other. The result is the “emergence” of attributes of the metaphoric vehicle that are sufficiently abstract to be attributes also of the metaphoric topic. The cumulative effect of successive metaphoric/literal categorical transformations produces a higher-level form of metacognition that is consistent with a neo-Kantian account of sublime feeling. Sublime feeling occurs as either sublime disquietude (existential dreams) or as sublime enthrallment (transcendent dreams). The aftereffects of these two dream types are thematically iterative “living metaphors” that have existential (but not totalizing) abstract ontological import.

Soft set theory is a mathematical tool for dealing with uncertainty. This paper investigates limits of interval type of soft sets (for short, it-soft sets). The concept of it-soft sets is first introduced. Then, limits of it-soft sets are proposed and their properties are obtained. Next, point-wise continuity of it-soft sets and continuous it-soft sets are discussed. Finally, an application for rough sets is given.

: The radar multi target tracking (MTT) technique requires prior knowledge of a number of parameters about the sensor, the target and backgrounds. The Integrated Track Splitting (ITS) is a fully automatic track-while-scan (TWS) target tracking algorithm capable of extracting and tracking a target in a dense clutter environment using quality false track discrimination (FTD) methodology. The computational complexity in ITS algorithm is limited, compared to other algorithms they use statistical methods to discriminate between false and true tracks, such as multiple hypothesis tracking (MHT), mainly due to the FTD performed. The paper provides an analysis of tracking parameters that allows determining the limit of the possibility of successful target tracking. Extensive experiments have confirmed that the recursive determination of the probability of the existence of a track during tracking can confirm a true track and reject a false track. The clutter density, number of random occurred targets, targets load during the maneuver and the target detection probability were varied. The results of experiments, carried out via Monte Carlo simulations, shown over representative confirmed true tracks (CTT) diagrams, root mean square error position and normalized tracking efficiency parametric diagrams allow the user to select optimal multi-target tracking parameters for different scenarios and clutter densities.

Legacy risks from infrastructures and industrial installations often reveal themselves when a potential for failure has been discovered much later than at the stage of the design and construction of a structure. In which case, there might already be a problem with the legacy installation, or even a crisis, without having had an accident. When the hazard cannot be taken away, the question arises as to how much effort, if any, should be spent on improving the situation. The usefulness of the three archetypical approaches to this problem: setting a standard, the As Low As Reasonably Practicable approach and a case-by-case discourse approach are discussed for their applicability for these legacy risks. Although it would be desirable to retrofit legacy risks to previously set legal requirements as is the case when acceptability limits are set in law or demonstration of ALARP is demanded, it may be impossible to reduce the residual risk to an otherwise acceptable level without taking away or replacing the infrastructure, which is not acceptable either. Therefor in conclusion the only available solution to persistent legacy risk problems seems to be to have a thorough discussion with all relevant stakeholders until an agreement is in some way found.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

Contemporary financial systems, despite their inherent complexity and resilience, face significant challenges related to transparency, efficiency, and security. Notable deficiencies in transparency and emerging security vulnerabilities underscore the pressing need for innovative solutions in current financial practices. Hence, this paper introduces a financial distribution system based on a consortium blockchain. Given organizations’ preference for keeping sensitive data private, the partially decentralized nature of consortium blockchains plays a pivotal role in the proposed system’s architecture. Moreover, within this system, the proposed smart contract serves a dual role. It functions not only as a transactional tool but also as a specialized solution designed to improve transactional procedures. Its multifaceted capabilities include ensuring data accuracy, facilitating swift execution, and ensuring adherence to regulatory requirements within the dynamic financial distribution landscape. Through rigorous testing and empirical analysis utilizing the Hyperledger Besu platform, it has been observed that the performance of the proposed system surpasses traditional blockchain frameworks. The results unequivocally demonstrate the proposed system’s proficiency in handling high-frequency financial transactions with minimal computational burden.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Aim: The aim of this study is to evaluate the possibility of discriminating between the two sexes through the simultaneous use of cheiloscopy and palatine rugoscopy. Materials and methods: 80 palate and lip impressions (40 male and 40 female) were analyzed. The palate impressions were acquired using both analogue and digital methods. The lip impres-sions were first acquired analogically and then scanned. The morphology of the palatine rugae in the palate impressions was analyzed, with the exclusion of segmental rugae. The lip prints were analyzed in sextants and the morphology of the lip wrinkles was evaluated. Results: Palatine rugoscopy shows that women have more curvy rugae than men and that men have more rugae on the left side than on the right. Cheiloscopy gave no statistically significant re-sults. Discussion: Palatine rugoscopy showed some differences between the sexes, however, these re-sults were not solid enough for reliable sex discrimination. Differences between the results of dif-ferent studies can be attributed to ethnic and methodological variations. Cheiloscopy, on the other hand, did not provide statistically significant results for sex discrimination. Conclusions: Given the scant results obtained from palatine rugoscopy and the lack of statisti-cally relevant results in cheiloscopy, together with a lack of concordance among the data found in literature, it is believed that it is not possible to discriminate between the two sexes by using the two methods contemporarily. Further research is needed.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

Background: the study aimed at comparing the prognostic importance of Heart Rate (HR) and of QT corrected (QTc) according to Fridericia, Framingham and Bazett methods, in a large non-selected population. Methods: the analysis of digital Electrocardiograms archived from 2008 to 2022 in the metropolitan area of Modena, Italy, was made. The population under study was divided into three age-groups and survival analysis was performed. Results: 131.627 patients were enrolled and during the follow-up (mean 1641.4 days), all-cause mortality was 8.9%. Both HR and QTc were associated with mortality. All-cause mortality significantly increased from HR values greater than 81 BPM and from QTc values greater than 440 msec in young subjects and 455 msec in old subjects (values of the 75th percentiles/optimal operating point). Cox analysis confirmed the better prognostic value of Bazett’s QTc and of HR in the whole population and in the three age-groups. Conclusion: Bazett’s method performed better than other methods but unexpectedly HR had the same or a better correlation with all-cause mortality. Since HR is simple and readily available, its evaluation should be improved. However, reference values for QTc and for HR are difficult to define causing many confounding factors and further population-study are required.

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

In forensic acoustics, a possible area of analysis is represented by unwanted sound that 1 is perceived as a source of intrusion or disturbance within a certain auditory context. This context 2 is defined as the "auditory scene" and refers to the set of sounds present in a specific environment. 3 The presence of unwanted sounds in the auditory scene can cause a wide range of negative effects, 4 including disturbance, discomfort, moral or immoral harm, and other types of negative impact on the 5 health and well-being of individuals exposed to noise. In 2022, the technical specification UNI/TS 6 11844:2022 dedicated to the measurement and analysis of intrusive noise was published. The standard 7 introduces the concept of intrusive noise and defines its calculation methods based on environmental 8 measurements. The purposes of this technical specification is to provide an objective support to 9 methods already in used in acoustic disputes, where the assessment of the annoyance of a noise is 10 often a subjective evaluation of the technician. This work delves into the application to some real 11 cases, identifying the potentiality and the limits of the standardized method.

Small Island States (SIDS) are among the nations most exposed to climate change (CC) and are characterised by a high degree of vulnerability. Their special nature means there is a need for more studies focused on the limits to CC adaptation on such fragile nations, particularly in respect of their problems and constraints. This paper addressed a perceived need for research into the limitations of adaptation on SIDS, focusing on the many restrictions which are unique to them. The main research question raised by this study was that how and to what extent the challenges by human activities (e.g., agriculture and tourism) posed to coastlines of SIDS could be addressed. This paper identified and described the adaptation limits they have, by using a review of the literature and an analysis of case studies from a sample of five SIDS in the Caribbean and Pacific regions (Barbados, Trinidad and Tobago, Cook Islands, Fiji, Solomon Islands, and Tonga). The findings of this research showed that an adaptable SIDS is characterised by awareness of various values, appreciation and understanding of a diversity of impacts and vulnerabilities, and acceptance of certain losses through change. The implications of this paper are two-fold. It explains why island nations continue to suffer from the impacts of CC, and suggest some of the means via which adequate policies may support SIDS in their efforts to cope with the threats associated with a changing climate. This study concluded that, despite the technological and ecological limits (hard limits) affecting natural systems, adaptation to CC is not only limited by such complex forces, but also by societal factors (soft limits) that could potentially be overcome by more adequate adaptation strategies.

Background: The antimalarial drug chloroquine and antimicrobial drug azithromycin have received significant attention during the current COVID-19 pandemic. Both drugs can alter cardiac electrophysiology and have been associated with drug-induced arrhythmias. Meanwhile, sympathetic activation is commonly observed during systemic inflammation and oxidative stress (e.g., in SARS-CoV-2 infection), and may influence the electrophysiological effects of chloroquine and azithromycin. Here, we investigated the effect of beta-adrenergic stimulation on proarrhythmic properties of chloroquine and azithromycin using a detailed in silico model of ventricular electrophysiology. Methods: Concentration-dependent chloroquine and azithromycin-induced alterations in ion-channel function were incorporated into the Heijman canine ventricular cardiomyocyte model. Single and combined drug effects on action-potential (AP) properties were analyzed using a population of 592 models accommodating inter-individual variability. Sympathetic stimulation was simulated by an increase in pacing rate and experimentally validated isoproterenol-induced changes in ion-channel function. Results: At 1 Hz pacing, therapeutic doses of chloroquine and azithromycin (5 and 20 µM, respectively) individually prolonged AP duration (APD) by 33% and 13%. Their combination produced synergistic APD prolongation (+161%) with incidence of proarrhythmic early afterdepolarizations in 53.5% of models. Increasing the pacing frequency to 2 Hz shortened APD and together with 1 µM isoproterenol corrected the drug-induced APD prolongation. No afterdepolarizations occurred following increased rate and simulated application of 0.1-1 µM isoproterenol. Conclusion: Sympathetic stimulation limits chloroquine- and azithromycin-induced proarrhythmia by reducing their APD-prolonging effect, suggesting the importance of heart rate and autonomic status monitoring in particular conditions (e.g., COVID-19).

Forest ecosystems make a greater contribution to carbon (C) stocks than any other terrestrial ecosystem. To understand the role of regional forest ecosystems in global climate change and carbon exchange, forest C stock and its spatial distribution within the small (2,300 km2) Liuxihe River basin were analyzed to determine the different contributors to the C stock. Forest C stocks were quantified by measuring the biomass of trees, understory vegetation, litter and roots, as well as soil organic C, using data from field samples and laboratory experiments. The results showed that forests stored 38.04 Tg C in the entire basin, with secondary and planted forests accounting for 89.82% and 10.18%, respectively, of the stored C. Five types of forests, a subtropical evergreen broad-leaved forest, a subtropical coniferous and broad-leaved mixed forest, a subtropical coniferous forest, a timber forest, and a non-wood forest, stored 257.55 ± 15.01, 218.92 ± 9.59, 195.24 ± 18.29, 177.42 ± 17.55, and 117.86 ± 6.04 Mg C ha−1, respectively. In the forest ecosystem C stocks of the basin, soils averagely contribute about 73.78%, not including root underground biomass. It provides a comprehensive method for forest ecosystem carbon investigation and forest management in small basin scale.

During the last forty years, the use of strontium isotopes in archaeology and biogeochemical research has spread widely. These isotopes, alone or in combination with others, can contribute to trace past and present environmental conditions. However, the interpretation of the isotopic values of strontium is not always simple and requires good knowledge of geochemistry and geology. This short paper on the use of strontium isotopes is aimed at those who use this tool (archaeologists, but not only) but who do not have a thorough knowledge of mineralogy, geology, and geochemistry necessary for a good understanding of natural processes involving these isotopes. We report basic knowledge and suggestions for a correct use of these isotopes. The isotopic characteristics of bio-assimilable strontium depend not so much on the isotopic characteristics of the bulk rock as, rather, on that of its more soluble minerals. Before studying human, animal and plant remains, the state of conservation and any conditions of isotopic pollution should be carefully checked. Samples should be collected according to random sampling rules. The data should be treated by a statistical approach. To make comparisons between different areas, it should be borne in mind that the study of current soils can be misleading since the mineralogical modification of the soil over time can be very rapid.

This paper describes a research project carried out in an Italian public school to assess whether parents were willing to take part in food procurement decisions, as well as their ability to accurately predict what foods children would pick at school lunch and their propensity to support sustainable food choices made by the school. The methodology included a questionnaire to 500 parents and an in-depth study of 138 child/parent pairs. The study comprised: (i) presentation of an innovative recipe in the weekly menu of the school canteen; (ii) meal observations of children’s intake at school lunch during the week of the menu modification; (iii) collection of both parents’ and children’s reports on their choices of recipes from the modified weekly menu. The results are commented in light of two important changes that have recently affected Italian public school food procurement: the opening of school canteens to lunches brought from home and the measures adopted since 2020 to contain the Covid-19 pandemic. Both events go in the direction of delegating to parents the multifaceted role of the school in the food arena. The article concludes that the results of the study should discourage this approach.

Packaged water consumption has grown rapidly in urban areas of many low and middle income countries, but particularly in Ghana. However, the sources of water used by this growing packaged water industry and its implications for water resource management and transport-related environmental impacts have not been described. This study aimed to assess the spatial distribution of regulated packaged water production in Ghana, both in relation to demand and for natural mineral water, to hydrogeological characteristics. 764 addresses for premises licenced to produce packaged water from 2009-2015 were mapped and compared to regional sachet water consumption and beverage import/export data examined. We find evidence to suggest packaged water is transported shorter distances in Ghana than in developed countries. For natural mineral waters, producers should be able to address the most widespread water quality hazards (including high salinity, iron and nitrates) in aquifers used for production through reverse osmosis treatment. The study suggests there is scope to integrate beverage product and groundwater regulatory databases to support groundwater management.

A quark nugget is a hypothetical dark-matter candidate composed of approximately equal numbers of up, down, and strange quarks. Most models of quark nuggets do not include effects of their intrinsic magnetic field. However, Tatsumi used a mathematically tractable approximation of the Standard Model of Particle Physics and found that the cores of magnetar pulsars may be quark-nuggets in a ferromagnetic-liquid state with surface magnetic field Bo = $10^(12±1) T. We have applied that result to quark-nugget dark matter. Previous work addressed the formation and aggregation of magnetized quark nuggets (MQNs) into a broad and magnetically stabilized mass distribution before they could decay and addressed their interaction with normal matter through their magnetopause, losing translational velocity while gaining rotational velocity and radiating electromagnetic energy. The two orders of magnitude uncertainty in Tatsumi’s estimate for Bo precludes the practical design of systematic experiments to detect MQNs through their predicted interaction with matter. In this paper, we examine episodic events consistent with a unique signature of MQNs. If they are indeed caused by MQNs, they constrain the most likely values of Bo = 1.65 × 10^12 T +/- 21% and support the design of definitive tests of the MQN dark-matter hypothesis.

This paper aims to raise awareness on certain interoperability issues as we intend to shape industry 5.0 in order to enable a human-centric resilient society. We advocate that the need of sharing small and specific data will become more intensive as AI-based solutions will become more pervasive. Consequently, dataspaces should be carefully designed to address this need. We advance the conversation by presenting a case study from HR demonstrating how to predict the possibility of an employee experiencing attrition. Our experimental results show that we need more than 500 samples for developing a machine learning model to be sufficiently capable to generalize the problem. Consequently, our experimental results show the feasibility of the idea. However, in small and medium sized companies this approach cannot be implemented due to the limited number of samples. At the same time, we advocate that this obstacle may be overcome if multiple companies will join a shared dataspace, thus raising interoperability issues

There is growing awareness that “Nature-based Solutions” (NbS) can help to protect us from climate change impacts whilst slowing further warming, supporting biodiversity and securing ecosystem services. However, the potential of NbS to provide the intended benefits has not been rigorously assessed. There are concerns over their reliability and cost-effectiveness compared to engineered alternatives, and their resilience to climate change. Trade-offs can arise if climate mitigation policy encourages NbS with low biodiversity value, such as afforestation with non-native monocultures. This can result in maladaptation, especially in a rapidly changing world where biodiversity-based resilience and multifunctional landscapes are key. Here we highlight the rise of NbS in climate policy—focussing on their potential for climate change adaptation as well as mitigation—and discuss barriers to their evidence-based implementation. We outline the major financial and governance challenges to implementing NbS at scale, highlighting avenues for further research. As climate policy turns increasingly towards greenhouse gas removal approaches such as afforestation, we stress the urgent need for natural and social scientists to engage with policymakers. They must ensure that NbS can achieve their potential to tackle both the climate and biodiversity crisis while also contributing to sustainable development. This will require systemic change in the way we conduct research and run our institutions.

The study carried out by simulation, concerns the thermal behavior of an office building’s solar fresh air cooling system, based on a LiBr-H₂O absorption chiller in different climatic conditions. The coefficient of performance (COP) and the solar fraction were considered performance parameters and were analyzed with respect to the operating limits: risk of crystallization and maintaining at least a minimum degassing zone. A new correlation between the required solar hot temperature and the cooling water temperature was established and then embedded in another new correlation between the COP and the cooling water temperature that was used in simulations during the whole cooling season corresponding to each location. It was found that: the solar hot water should be maintained in the range of (80-100) °C depending on the cooling water temperature, the COP of the solar LiBr-H₂O absorption chiller with or without cold storage tank can reach (76.5-82.4) % depending on the location, and the solar fraction can reach (29.5-62.0) % without cold storage tank and can exceed 100 % with cold storage tank, the excess cooling power being available to cover other types of cooling loads: through the building envelope, from lighting, from occupants, etc.

We extend Ziv and Lempel's model of finite-state encoders to the realm of lossy compression of individual sequences. In particular, the model of the encoder includes a finite-state reconstruction codebook followed by an information lossless finite-state encoder that compresses the reconstruction codeword with no additional distortion. We first derive two different lower bounds to the compression ratio that depend on the number of states of the lossless encoder. Both bounds are asymptotically achievable by conceptually simple coding schemes. We then show that when the number of states of the lossless encoder is large enough in terms of the reconstruction block-length, the performance can be improved, sometimes significantly so. In particular, the improved performance is achievable using a random-coding ensemble that is universal, not only in terms of the source sequence, but also in terms of the distortion measure.

During most of the lifespan of the Venetian republic, doges or presidents were elected for life. However, a long tenure was a rare event, which effectively resulted in term limits, as has already been deported by several authors. In this paper we examine these tenures and its evolution during the existence of the Venetian republic, trying to prove Smith et al. thesis, but also the event or events that effectively caused that limitation by design. Finally, we will discuss for the causes of this limitation and its effective consequences.

Recent analyses of cosmic microwave background (CMB) maps have been interpreted as demonstrating that the Universe was born without an initial rotation. However, these analyses are based on unrealistic models and do not contain essential ingredients such as quantum effects, the strong, weak and gravitational interactions between the components, their intrinsic spins and magnetic moments, as well as primordial black holes. If the Universe was born spinning these effects would distribute the initial spin angular momentum among its components long before the CMB forms at recombination. A primordial spin would now appear as a nonzero total angular momentum of its components along the direction of the original spin, and a primordial large-scale rotation would no longer be apparent. The existence of a special axis or direction would break a fundamental symmetry assumed in general relativity, cosmic isotropy, and a net angular momentum implies a cosmic parity violation.

This study explores the Edaravone solubility space encompassing both neat and binary dissolution media. The efforts were made toward revealing the concentration limits inherently associated with common pure and mixed solvents. For this purpose, the published solubility data of the title drug were scrupulously inspected and cured. This enabled to make the dataset consistent and coherent. However, the lack of some important types of solvents in the collection called for an extension of the available pool of Edaravone solubility data. Hence, new measurements were performed for collecting Edaravone solubility in polar non-protic and polar di-protic media. Such an extended set of data was used for tuning the parameters of regressors models and formulating the ensemble for predicting new data. In both phases, namely the model training and ensemble formulation, close attention was paid not only to minimizing the deviation of computed values from the experimental ones but also to ensuring the high predictive power and computing solubility for new systems. Furthermore, the environmental friendliness characteristics determined based on the common green solvent selection criteria was included in the analysis. Our applied protocol led to the conclusion that the solubility space defined by ordinary solvents is limited, and it is unlikely to find solvents that are more suited for Edaravone dissolution than those depicted in this manuscript. The theoretical framework presented in this study provides a precise guide for conducting experiments, saving time and resources in the pursuit of new findings.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

A quantum Otto engine with a single ion harmonic oscillator as its working substance is studied for an adiabatic operation at high and low temperature limits. Using the universal optimization method, the heat engine is effectively optimized and found to yield better working conditions in some ranges of temperature ratios. Accordingly, the figure of merit, ψ, is found to be greater than unity in the range: 0<β2β1≤0.12; showing that the heat engine performs better in the optimized condition than in the maximum power working condition. ψ is determined to be less than one in the range 0.12≤β2β1≤0.35 under the same temperature limit ; depicting that the maximum power working condition is preferred to the optimized working condition. On the other hand, in the low temperature limit, the figure of merit, ψ, is found to be greater than unity in the range 3.7<ω1ω2≤18; revealing that optimized working condition is better than the maximum power working condition for the heat engine. In the same temperature limit, ψ is found to be less than one in the range 0≤ω1ω2≤3.7; showing that maximum power working condition is preferred to the optimized one. For the model of heat engine studied, in some ranges of temperature ratio, it is found to work better in the optimized condition, whereas in the other ranges it performs better under the maximum power working condition. So, it is possible to switch the engine between the two conditions depending on one’s need.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

Cyanobacteria are ubiquitous phototrophic bacteria that inhabit diverse environments across the planet. They dominate many eutrophic lakes impacted by excess nitrogen (N) and phosphorus (P) forming dense accumulations of biomass known as cyanobacterial harmful algal blooms or cyanoHABs. Their dominance in eutrophic lakes is attributed to a variety of unique adaptations including N and P concentrating mechanisms, N fixation, colony formation that inhibits predation, vertical movement via gas vesicles, and the production of toxic or otherwise bioactive molecules. While some of these molecules have been explored for their medicinal benefits, others are potent toxins harmful to humans, animals, and other wildlife known as cyanotoxins. In humans these cyanotoxins affect various tissues, including the liver, central and peripheral nervous system, kidneys, and reproductive organs among others. They induce acute effects at low doses in the parts-per-billion range and some are tumor promoters linked to chronic diseases such as liver and colorectal cancer. The occurrence of cyanoHABs and cyanotoxins in lakes presents challenges for maintaining safe recreational aquatic environments and the production of potable drinking water. CyanoHABs are a growing problem in the North American (Laurentian) Great Lakes basin. This review summarizes information on the occurrence of cyanoHABs in the Great Lakes, toxicological effects of cyanotoxins, and appropriate numerical limits on cyanotoxins in finished drinking water.

This paper describe a procedure to measure experimentally the power coefficient, Cp, of winged seeds, and apply this technique to seeds from the Norway maple (Acer platanoides). We measure Cp=56.9±2% at a tip speed ratio of 3.21±0.06. Our results are in agreement with previously published CFD simulations that indicate that these seeds – operating in low-Reynolds number conditions – approach the Betz limit (Cp=59.3%) the maximum possible efficiency for a wind turbine. In addition, this result is not consistent with the recent theoretical work of Okulov & Sørensen, which suggests that a single-bladed turbine with a tip-speed ratio of 3.2 can achieve a power efficiency of no more than 30%.

Clinical agreement between two quantitative measurements on a group of subjects is generally assessed with the help of the Bland-Altman (B-A) limits. The interpretation regarding agreement is based on whether B-A limits are within the pre-specified clinical tolerance. Thus, clinical tolerance limits are necessary for this method. We argue in this communication that such limits of clinical tolerance can be directly used for assessing agreement and plead that this nonparametric approach is simple and robust to the distribution pattern and outliers. Such direct use of clinical tolerance limits has more flexibility, and it is more effective in assessing the extent of agreement.

Rising temperature is among the most remarkably stressful phenomena induced by global climate changes with negative impacts on crop productivity and quality. It has been previously shown that volatiles belonging to the isoprenoid family can confer protection against abiotic stresses. In this work, two Vitis vinifera cv. ‘Chardonnay’ clones (SMA130 and INRA809) differing for a mutation of the DXS gene encoding for 1-deoxy-D-xylulose-5-phosphate (the first dedicated enzyme of the 2C-methyl-D-erythritol-4-phosphate (MEP) pathway) and involved in the regulation of isoprenoids biosynthesis were investigated in field trials and laboratory experiments. Leaf monoterpene emission, chlorophyll fluorescence and gas-exchange measurements were assessed over three seasons at different phenological stages and either carried out in vivo or controlled conditions under contrasting temperatures. A significant (p<0.001) increase in leaf monoterpene emission was observed in INRA809 when plants were experiencing high temperatures and over two experiments while no differences were recorded for SMA130. Significant variation was observed for the rate of leaf CO2 assimilation under heat stress, with INRA809 maintaining higher photosynthetic rates and stomatal conductance values than SMA130 (p=0.003) when leaf temperature increased above 30°C. At the same time, maximum photochemical quantum yield of PSII (Fv/Fm) was affected by heat stress in the non-emitting clone (SMA130), while the INRA809 showed a significant resilience of PSII under elevated temperature conditions. Consistent data were recorded between field seasons and temperature treatments in controlled environment conditions suggesting a strong influence of monoterpene emission on heat tolerance under elevated temperatures. This work provides further insights on the photoprotective role of isoprenoids under high temperatures in Vitis vinifera and additional studies should focus at unravelling the mechanisms underlying heat tolerance on the monoterpene-emitter grapevine clone.

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.

The activity of innovative practice relates to seizing opportunities now for patients in desperate situations and the ethical dilemmas around it. Sadly, the term innovation has multiple meanings, adding confusion and misunderstanding to an already difficult debate. This paper aims to enhance the definition of innovative practice in two ways. Fist, we propose to curb ambiguity by replacing the term "innovative practice" with the more precise of "new non-validated practice" and by distinguishing the specific meaning of innovation at stake. To identify this meaning, we analyse the traditional research ethics’ distinction between research, validated practice, and innovation. Second, we propose the following unified definition of "new non-validated practice", that is, the first or recent use of diagnostic, therapeutic or preventive interventions that introduce a significant change (new); with an insufficient level of evidence of safety or efficacy for regular healthcare (non-validated); and with the main aim to benefit patients (practice). To avoid objections to our definition, we analyse its three core elements (significant novelty, insufficient validation for, and patients' best interests) and we present a 2D classification of medical practice that follows from our definition. If sound, our enhanced definition of "new non-validated practice" allows comparing exceptional activities in different fields of medicine that previously have been considered unconnected (e.g. compassionate use of investigational drugs, humanitarian uses of devices, novel off-label uses, etc.). In turn, it also provides a promising conceptual tool to inform empirical research, discuss responsible access to innovative care and evaluate the regulation of innovative practice (e.g. right-to-try laws).

The main purpose of this paper is to introduce and investigate degenerate Poisson distrib- ution which is a new extension of the Poisson distribution including the degenerate expo- nential function. We then provide several properties of the degenerate Poisson distribution such as the first and the second raw moments and di¤erence operator property. Moreover, we acquired the skewness and the kurtosis for the degenerate Poisson distribution. We also derive its moment generating function by which we define the degenerate Bell polynomials and give a connection for these polynomials related to the unsigned Stirling numbers of the …rst kind.

Atmospheric turbulence characteristics are essential in determining the quality of astronomical images and implementing adaptive optics systems. In this study, the vertical distributions of optical turbulence at the Peak Terskol observatory (43.27472 ° N 42.50083 ° E, 3127 m a.s.l.) using the Era-5 re-analysis and scintillation measurements are investigated. For the closest reanalysis grid node to the observatory, vertical profiles of the structural constant of the air refractive index turbulent fluctuations Cn2 were obtained. The calculated Cn2(z) vertical profiles are compared with the vertical distribution of turbulence intensity obtained from tomographic measurements with Shack-Hartmann sensor. The atmospheric coherence length at the location of Terskol Peak was estimated. Using combination of atmospheric models and scheme paramaterization of turbulence, Cn2(z) profiles at Mt. Kurapdag were obtained. The values of atmospheric coherence length at the Peak Terskol are compared with estimated values of this length at the ten astronomical sites including Ali, Lenghu and Daocheng.

The analysis of the current safety standards for electric toys showed that the normative intensity limits for visible light emitted by LEDs integrated in toys are overestimated. These limits were originally set in a scientific article published in 2012 that was adapted into the international safety standard published in 2017, and into the subsequent European and national standards, all published in 2020. The overestimation of the intensity limits results from several errors made in the original article. Accordingly, the current normative intensity limits for visible light used in toys do not protect the children’s eyes against adverse effects of exposure to high intensity LEDs which may compromise their visual health. Updating the safety standards for electric toys using a method based on robust scientific data is recommended to protect children's visual health and ensure their long-term well-being.

The theoretical limits of water sorbate based chemical sorption heat storage are investigated in this study. First, a classification of \textit{thermochemical heat storage} is proposed based on bonding typology. Then, thermodynamics of chemical solid/gas sorption is introduced. The analysis of the reaction enthalpy from the literature indicates that this value is only slightly varying for one mole of water. Using this observation, and with the help of thermodynamical considerations, it is possible to derive conclusions on energy efficiency of closed and open heat storage systems. Whatever the salt, the main results are 1) the energy required for evaporation of water is, at least, 65% of the available energy of reaction and 2) the maximum theoretical energy efficiency of the system is about 1.8.

Currently, there is no widely accepted consensus regarding a consistent thermodynamic framework within the special relativity paradigm. However, by postulating that the inverse temperature 4-vector, denoted as β, is future-directed and timelike, intriguing insights emerge. Specifically, it is demonstrated that the q-dependent Tsallis distribution can be conceptualized as a de-Sitterian deformation of the relativistic Maxwell-Jüttner distribution. In this context, the curvature of the de Sitter space-time is characterized by Λ/3, where Λ represents the cosmological constant within the ΛCDM standard model for Cosmology. For a simple gas composed of particles with proper mass m, and within the framework of quantum statistical de Sitterian considerations, the Tsallis parameter q exhibits a dependence on the cosmological constant given by q=1+ℓcΛ/n where ℓc=ℏ/mc is the Compton length of the particle and n is a positive numerical factor. This formulation establishes a novel connection between the Tsallis distribution, quantum statistics, and the cosmological constant, shedding light on the intricate interplay between relativistic thermodynamics and fundamental cosmological parameters.

As the search for exoplanets continues, more are being discovered orbiting Red Giant stars. We use current data from the NASA Exoplanet Archive to investigate planet distribution around Red Giant stars and their presence in the host’s habitable zone. As well, we explore the distribution of planet mass and orbital semi major axis for evolved stars with increasing stellar radii. We found 9 Red Giant-hosted exoplanets, and 21 Subgiant-hosted exoplanets to be in the optimistically calculated habitable zone, 5 and 17 of which are in a more conservatively calculated habitable zone. All the planets detected within their habitable zone orbit stars that are in early stages of evolution. We believe that with more powerful instrumentation, more habitable planets may be found around stars that are in later stages of evolution.

the intermittency and variability of these permeated Distributed Generators (DGs) could critically cause many security and economy risks to distribution systems. This paper applied a certain mathematical distribution to imitate the output variability and uncertainty of DGs. And then, four risk indices EENS, PLC, EFLC and SI were established to reflect the system risk level of distribution system. For the certain mathematical distribution of the DGs' output power, a developed PEM (point estimate method)-based method was proposed to calculate these four system risk indices. In this developed PEM-based method, enumeration method was used to list the states of distribution systems, an improved PEM was presented to deal with the uncertainties of DGs and the value of load curtailment in distribution systems was calculated by an optimal power flow algorithm. Finally, the effectiveness and advantages of this proposed PEM-based method for distribution system assessment were verified by the tests of a modified IEEE 30-bus system. Simulation results have shown that this proposed PEM-based method has a high computational accuracy and highly reduced computational costs compared with other risk assessment methods and is very effective for risk assessments.

L\'evy walks represent important modeling tools for variety of real life processes. Their natural scaling limits are known to be described by the so-called material fractional derivatives. So far these scaling limits were derived for spatially homogeneous walks, where Fourier and Laplace transforms represent natural tools of analysis. Here we derive the corresponding limiting equations in the case of position depending times and velocities of walks, where Fourier transforms cannot be effectively applied. In fact, we derive three different limits (specified by the way the process is stopped at an attempt to cross the boundary), leading to three different multi-dimensional versions of Caputo-Dzherbashian derivatives, which correspond to different boundary conditions for the generators of the related Feller semigroups and processes. Some other extensions and generalisations are analysed.

This work shows the potential of a new way of co-treatment of domestic wastewater (DWW) and a liquid stream coming from the thermal hydrolysis of the organic fraction of municipal solid waste (OFMSW) mediated by a mixed culture of purple phototrophic bacteria (PPB) capable of assimilating carbon and nutrients from the medium. The biological system is an open single-step process operated under microaerophilic conditions at an oxidative reduction potential (ORP) &lt; 0 mV with a photoperiod of 12/24 h and fed during the light Stage only, so the results can be extrapolated to outdoors open ponds operation by monitoring the ORP. The effluent mostly complies with the discharge values of the Spanish legislation in COD and P values (&lt;125mg/L &lt;2 mg/L), respectively, and punctually on values in N (&lt;15mg/L). Applying an HRT of 3 d and a ratio of 100:7 (COD:N), the presence of PPB in the mixed culture surpassed 50% of 16S rRNA gene copies, removing 78% of COD, 53% of N and 66% of P. Furthermore, increasing the HRT to 5 d, removal efficiencies of 83% of COD, 65% of N and 91% of P were achieved. In addition, the reactors were further operated in a membrane bioreactor, thus separating the HRT from the SRT to increase the specific loading rate. Very satisfactory removal efficiencies were achieved by applying HRT and SRT of 2.3 and 3 d, respectively: 84% of COD, 49% of N and 93% of P despite low presence of PPB due to more oxidative conditions, which anyway step-by-step re-colonized the mixed culture until reaching &gt;20% of 16S rRNA gene copies after 49 d of operation. These results open the door to scale up the process in open photobioreactors capable of treating urban wastewater and municipal solid waste in a single stage and under microaerophilic conditions by controlling the ORP of the system. This novel urban biorefinery allows reducing treatment costs of two urban wastes and embed them in the circular bioeconomy through water recycling and valorizing PPB biomass as a source of carbon, nitrogen and phosphorus.

In geotechnical engineering applications, it is very important to obtain the undrained shear strength of remolded soils accurately and reliably. This study aims to obtain a trustworthy solution to determine the undrained shear strength of remolded clay mixtures using Atterberg limit test results in various states of consistency. An experimental study was carried out involving a wide range of clay mixtures of varying plasticity and geological origin. In the analyses, the variation of the remolded undrained shear strength depending on the cone penetration depth, water content, flow index, liquidity index and log liquidity index were investigated. In the study, the highest undrained shear strength of 100% Na-montmorillonite (NaM) was obtained at 171.89 kPa at 56.60% water content, while the lowest undrained shear strength was obtained for 100% Sepiolite (S), 9.28 kPa at 31.65% water content. The results of this study revealed that the shear strength is significantly affected by soil conditions, rather than dominant clay mineral. Besides, it was observed that the undrained shear strength at the plastic limit was approximately 30-35 times greater than that at liquid limit. The equations of liquid limit-flow index and plasticity index- flow index were proposed. It was concluded that the interdependence between undrained shear strength, liquidity index, log liquidity index, and flow index is not unique due to the different physical and chemical properties of clays.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

This article introduces an innovative design method for public lighting systems that surpasses the limitations of conventional approaches, which rely on predefined lamp characteristics and spatial arrangement. By employing a multi-criteria decision algorithm, our study proposes an optimal design methodology considering several key aspects, including the distance between lamps, their type, power, and light distribution. The goal is to achieve optimal illumination that enhances visibility on public roads for drivers and pedestrians while simultaneously minimizing glare, installation costs and maximizing energy efficiency. The proposed methodology is implemented through an algorithm developed in Matlab, with results validated through simulations in Dialux. This information is used to construct a decision matrix, assessed using the CRITIC method across 180 different scenarios within a specific case study. The findings demonstrate the effectiveness of multi-criteria decision-making as a tool for significantly improving the planning and design of lighting in public illumination systems, allowing for selecting the optimal combination of parameters that ensure the best lighting conditions.

One of the most important problems in the presence of epidemics and pandemics is an accurate prediction and preparedness. Scholars and experts argue that future pandemics and/or epidemics are almost inevitable events and is not whether next pandemics will happen, but when a new heath emergency will emerge. Epidemiologic models for prediction of Coronavirus Disease 2019 (COVID-19) have shown many limitations because of unpredictable dynamics of the new viral agent SARS-CoV-2 in environment and society. The main goals of this study are twofold: first, the analysis of anthropogenic activities and factors that may trigger pandemic threats; second, the planning of new directions for strategies to reduce risks that a pandemic threat emerges and/or in the initial phase to reduce vast diffusion and negative impact of new viral agents that can generate hazards and problems in public health, environment and socioeconomic systems. In particular, the investigation and understanding of sources and driving factors concerning the emergence and diffusion of new pandemics have critical aspects for strategic actions of forecast, prevention and preparation of effective policy responses to cope with next pandemic crises and health emergencies. Insights here endeavor, whenever possible, to clarify these problems to increase the knowledge of the sources and factor determining the emergence of new viral agents in order to design optimal response policies to face next pandemic diseases similar to COVID-19. .

The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

Developments of new probability models for data analysis are keen interest of importance for all fields. The log-Dagum distribution has a prominent role in the theory and practice of statistics. In this article, a new family of continuous distributions generated from a log Dagum random variable called the log-Dagum Weibull distribution is proposed. The key properties of the proposed distribution are derived. Its density function can be symmetrical, left-skewed, right-skewed and reversed-J shaped and can have increasing, decreasing, bathtub hazard rates shaped. The model parameters are estimated by the method of maximum likelihood and illustrate its importance by means of applications to real data sets.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

Safety limits application has always been a traditional approach to ensure the safe operation of electro-mechanical systems within many industries including automated vehicles, robotics, aerospace, traditional automotive, railways, manufacturing, etc. In all of these applications, control and safety limits are usually hard-coded into the production firmware and are fixed throughout the entire product life cycle. Currently, due to the evolving needs of automated systems like automated vehicles and robots, this traditional approach does not address all the use cases and scenarios to ensure safe operation. Especially for data-driven machine learning applications that constantly evolve and learn over time, it is important to be able to adjust the safety limits application strategy to be more flexible and adaptable based on different Operational Design Domains (ODDs) and scenarios. Our ITSC conference paper ~\cite{4} introduced the concept of a new safety limits application strategy called the Dynamic Control Limits Application (DCLA) strategy that supports the flexible application of diverse limits profiles based on the parameters involved within the dynamic scenario at different layers of the Autonomy software stack.This paper extends the DCLA strategy to derive the complete methodology for safety limits application based on ODD elements, scenario identification and scenario classification using Decision Making Engines. It leverages the layered architecture introduced in the ITSC conference paper to implement the Decision Making (DM) algorithms. Another important extension is the use of cloud infrastructure that is based on the Vehicle-to-Infrastructure (V2I) technology to store the scenarios and the limits mapping to serve as a ground truth and/or a backup mechanism in case of errors or failures associated with the main Decision Making (DM) Engine. There is also a focus on providing a more comprehensive list of scenarios and a custom built experimental dataset to cover the maximum ODD elements, and multiple tables of safety limits to be chosen from, which eventually helps in creating different safety limits application profiles. These distinct safety limits application profiles are based on the scenario parameters that are perceived by the system upon which the Decision Making algorithms are applied or trained. This systematic approach can be used within the industry for any of the future automated vehicles and systems until Level 5 Autonomy.

The Pannonian basin major heat system in Central Europe. Their peripheral basins like the East Slovakian basin is a example of a geothermal structure with a linear directed heat flow ranging from 90 to 100 mW /m2 from west to east. However, the use of the geothermal source is limited by several critical tectono-geologic factors: (a) tectonics, and the associated disintegration of the aquifer block by multiple deformations during the pre-Paleogene mainly Miocene period. The main discontinuities of NW-SE and N-S direction negatively affect the permeability of the environment. On the contrary, for utilization are important the secondary minor NE-SW dilatation open fractures which have developed by sinistral transtension on N–S faults and accelerated normal movements to the southeast in the present. (b) hydrogeological conditions, the geothermal structure accommodated three water types, namely Na-HCO3 with 10.9 g.l-1 mineralization (in the north), the Ca-Mg-HCO3 with 0.5 – 4.5 g.l-1 mineralization (in the west), and Na-Cl water type containing 26.8-33.4 g.l-1 (in the southwest) mineralization. The chemical composition is influenced by the Middle Triassic dolomites aquifer as well as by infiltration of saline solutions and meteoric waters along open fractures/faults. (c) geothermally anomalous heat 123 – 129 °C close to volcanic chain with 170 l/s total flow seems to be the perspective for heat production.

The construction of optimized biological fuel cells requires a cathode which combines the longevity of a microbial catalyst with the power density of an enzymatic catalyst. Laccase secreting fungi were grown directly on the cathode of a biological fuel cell to facilitate the exchange of inactive enzymes with active enzymes with the goal of extending the lifetime of laccase cathodes. Additionally, a functionally graded coating was developed to increase enzyme loading at the cathode. Directly incorporating the laccase producing fungus at the cathode extends the operational lifetime of laccase cathodes while eliminating the need for frequent replenishment of the electrolyte. Additionally, the hybrid microbial-enzymatic cathode addresses the issue of enzyme inactivation by using the natural ability of fungi to exchange inactive laccases at the cathode with active laccases. Finally, enzyme adsorption was increased through the use of a functionally graded coating containing an optimized ratio of titanium dioxide nanoparticles and single walled carbon nanotubes. The hybrid microbial-enzymatic fuel cell combines the higher power density of enzymatic fuel cells with the longevity of microbial fuel cells and demonstrates the feasibility of a self-regenerating fuel cell in which inactive laccases are continuously exchanged with active laccases.

Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydro-bulging tests are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

The Sentinel-2 satellite mission offers high resolution multispectral time series image data, enabling the production of detailed land cover maps globally. At this scale, the trade-off between processing time and result quality is a central design decision. Currently, this machine learning task is usually performed using pixelwise classification methods. The radical shift of the computer vision field away from hand engineered image features and towards more automation by representation learning comes with many promises, including higher quality results and less engineering effort. In this paper we assess fully convolutional neural networks architectures as replacements for a Random Forest classifier in an operational context for the production of high resolution land cover maps with Sentinel-2 time series at the country scale. Our contributions include a framework for working with Sentinel-2 L2A time series image data, an adaptation of the U-Net model for dealing with sparse annotation data while maintaining high resolution output, and an analysis of those results in the context of operational production of land cover maps.

Foodborne illnesses can be infectious and dangerous and most of them are caused by bacteria. Some types of common food-related bacteria exist widely in nature and pose a serious threat to both humans and animals, and can cause poisoning, diseases, disabilities and even death. Rapid, reliable and cost-effective methods for bacteria detection are of paramount importance in food-safety and environmental monitoring. Polymerase chain reaction (PCR), lateral flow immunochromatographic assay (LFIA) and electrochemical method have been widely used in food-safety and environmental monitoring. In this paper, the recent developments (2013-2023) covering PCR, LFIA and electrochemical method for various bacteria detection (Salmonella, Listeria, Campylobacter, Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli)) considering different foods types, analytical performances and the reported limit of detection (LOD) are discussed. It is found that the bacteria type and food sample type contribute significantly to the analytical performance and LOD. Detection by LFIA has higher average LOD (24 CFU/ml) than detection by electrochemical method (12 CFU/ml) and PCR (6 CFU/ml). Salmonella and E. coli in the Pseudomonadota domain usually have low LODs. LODs are usually lower for detection in fish and eggs. LFIA with gold and iron nanoparticles are prominent in the majority of articles of 26 CFU/ml and 12 CFU/ml respectively. Electrochemical method reveals that the average LOD is highest for cyclic voltammetry (CV) of 18 CFU/ml), followed by electrochemical impedance spectroscopy (EIS) of 12 CFU/ml and differential pulse voltammetry (DPV) of 8 CFU/ml. LOD usually decreases when replicate number increases until it remain unchanged. Exponential relations with (R²>0.95) between LOD of Listeria in milk by LFIA and electrochemical method with replicate number have been obtained. Finally, the review discusses the challenges and future perspectives (including the role of nanomaterials/advanced materials) to improve the analytical performance for bacterial detection.

The current manuscript presents a review on existing kiln burner technologies for the cement production process, in the context of the current climate of energy transition and environmental remediation. Environmental legislation has become ever stricter in response to global climate change, and cement plants need to adapt to this new reality in order to remain competitive in the market and ensure their longevity. The cement production process is a well-established technology with more than a century of existence. There are several plants in operation whose process is outdated by modern standards, particularly considering the current industry decarbonization needs. The cement process requires tremendous amounts of energy, mainly recovered from the combustion of solid, liquid or gaseous fuels, which yields massive emissions of greenhouse gases. Thus, an important onus is placed upon the minimization of pollutant emission in the combustion system, as well as a substitution of fossil fuels with more sustainable alternatives. One of the sus-tainable alternative fuels comes in the form of refuse derived fuels (RDF). These high caloric frac-tions of municipal solid waste present a double advantage by reducing the amount of fossil fuels used and reducing the landfilling fraction of waste. However, their use in rotary kiln burners comes with important limitations for burner operation, namely that a high degree of control over primary air supply is needed to ensure complete combustion with minimal pollutant emission.

According to Landauer’s principle, the energy of a particle may be used to record or erase N number of information bits within the thermal bath. The maximum number of information N recorded by the particle in the heat bath is found to be inversely proportional to its temperature T. If at least one bit of information is transferred from the particle to the medium, then the particle might exchange information with the medium. Therefore for at least one bit of information, the limiting mass that can carry or transform information assuming a temperature T= 2.73 K is equal to m = 4.71810-40 kg which is many orders of magnitude smaller that the masse of most of today’s elementary particles. Next, using the corresponding temperature of a graviton relic and assuming at least one bit of information the corresponding graviton mass is calculated and from that, a relation for the number of information N carried by a graviton as a function of the graviton mass mgr is derived. Furthermore, the range of information number contained in a graviton is also calculated for the given range of graviton mass as given by Nieto and Goldhaber, from which we find that the range of the graviton is inversely proportional to the information number N. Finally, treating the gravitons as harmonic oscillators in an enclosure of size R we derive the range of a graviton as a function of the cosmological parameters in the present era

Background Natural Saccharomyces cerevisiae yeast strains exhibit very large genotypic and phe-notypic diversity. Breeding programs taking advantage of this characteristic, are widely used for yeast selection in the wine industry, especially in the recent years when winemakers need to adapt their production to climate change. The aim of this work was to evaluate a Marker Assisted Se-lection (MAS) program to improve malic acid consumption capacity of Saccharomyces cerevisiae in grape juice. Methods Optimal individuals of two unrelated F1-hybrids were crossed to get a new genetic background carrying many “malic consumer” loci. Then, eleven QTLs already identified were used for implementing the MAS breeding program. Results By this way, extreme individuals able to consume more than 70% of malic acid in grape juice were selected. These individuals were tested in different enological matrixes and compared to their original parental strains. They greatly reduced the malic acid content at the end of alcoholic fermentations, they appeared to be robust to the environment and accelerate the ongoing of malo-lactic fermentations by Oenococcus oeni. Conclusions This study illustrates how MAS can be efficiently used for selecting industrial Saccharomyces cerevisiae strains with outlier properties for winemaking.

GANs are well known for success in the realistic image gen-eration. However, they can be applied in tabular data generation as well.We will review and examine some recent papers about tabular GANs inaction. We will generate data to make train distribution bring closer tothe test. Then compare model performance trained on the initial traindataset, with trained on the train with GAN generated data, also wetrain the model by sampling train by adversarial training. We show thatusing GAN might be an option in case of uneven data distribution be-tween train and test data

DiFX is a software VLBI correlator currently adopted by several main correlation sites around the globe. After the launch of the RadioAstron Space-VLBI mission in 2011, an extension was necessary to handle processing of an orbiting antenna, to be correlated with supporting ground arrays. We present here a branch of the main DiFX distribution (2.4), recently uploaded on the publicly available repository, that MPIfR developed to process data of the three AGN-imaging RadioAstron key science projects. It can account for general relativistic correction of an orbiting antenna with variable position/velocity, providing a routine to covert the native RDF format to the more common M5B one. Also, a fringe-finding algorithm able to manage arbitrary large fringe-search window is included, allowing one to increase the search space normally adopted by common software packages like HOPS.

The research on the distribution of rural buildings is one of the fundamental works of urban-rural development in Vietnam. Adopting Mask R-CNN deep learning framework and collecting sub-meter remote sensing images, this research used a remote sensing interpretation model of rural buildings trained based on East Asian characteristics of rural buildings and successfully recognized about 2.87 million rural buildings in 34 Vietnamese provincial administrative districts with a total area of rural buildings of 2,492 million square meters. The reliability of the identification results was verified by manual detection and quantitative statistics, and a multi-scale database of rural buildings in Vietnam based on individual rural buildings was created. Based on the database, this paper analyzes the distribution characteristics of rural buildings and summarizes characteristics of rural buildings distribution at the country, regional, and provincial scales. The identification results lay the foundation for the next study of urban-rural relations in Southeast Asia and the construction of a basic database on villages.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

The novel respiratory disease COVID-19 has reached the status of worldwide pandemic and large efforts are currently being undertaken in molecularly characterizing the virus causing it, SARS-CoV-2. The genomic variability of SARS-CoV-2 specimens scattered across the globe can underly geographically specific etiological effects. In the present study, we gather the 48,635 SARS-CoV-2 complete genomes currently available thanks to the collection endeavor of the GISAID consortium and thousands of contributing laboratories. We analyze and annotate all SARS-CoV-2 mutations compared with the reference Wuhan genome NC_045512.2, observing an average of 7.23 mutations per sample. Our analysis shows the prevalence of single nucleotide transitions as the major mutational type across the world. There exist at least three clades characterized by geographic and genomic specificity. In particular, the clade G, prevalent in Europe, carries a D614G mutation in the Spike protein, which is responsible for the initial interaction of the virus with the host human cell. Our analysis may drive local modulation of antiviral strategies based on the molecular specificities of this novel virus.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densi- ties and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on dierent set of true values. Some real data sets were employed to show the usefulness and exibility of the model which serves as generalization to many sub-models in the elds of engineering, medical, survival and reliability analysis.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densities and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on different set of true values. Some real data sets were employed to show the usefulness and flexibility of the model which serves as generalization to many sub-models in the field of engineering, medical, survival and reliability analysis.

For the polymer electrolyte fuel cell (PEFC), the separator thickness plays an important role to determine the weight, the volume and the costs of the PEFC. In addition, thermal management, i.e. temperature distribution is also important for the PEFC system to obtain higher performance. However, there were few reports investigating the relationship between the temperature distribution and the power generation performance such as current density distribution of PEFC operated at higher temperature (HT-PEFC). The aim of this study is to clarify the impact of separator thickness on the relationship between the temperature distribution and the current density distribution of HT-PEFC. This study has also investigated the impact of separator thickness on the relationship between the temperature distribution and the gases such as H2, O2 and the current density distribution of HT-PEFC numerically using CFD software COMSOL Multiphysics. The separator thicknesses of 2.0 mm, 1.5 mm and 1.0 mm were studied. In the study, the operation temperature and the relative humidity (RH) of supply gas were also changed. As a result, it was revealed that the optimum separator thickness was 2.0 mm to obtain higher power generation of HT-PEFC. Since the heat capacity in the case of the separator thickness of 2.0 mm was the largest among the separators investigated in this study, the dehydration of PEM and catalyst layer was smaller compared with the thinner separator thicknesses. It was also revealed that the impacts of separator thickness on distribution of gases, e.g. O2, H2O, and current density distribution became larger under higher temperature and lower RH conditions. This study also concluded that the tendency of temperature distribution matched those of O2, H2O and current density distributions.

Species have shown their habital variations in responding to climate change, especially during the spring and summer spawning seasons. The species distribution model (SDM) is considered the most favorable tool to study the potential effects of climate change on species distribution. Therefore, we developed the ensemble SDM to predict the changes in species distribution of Portunus trituberculatus among different seasons in 2050 and 2100 under the climate scenarios RCP4.5 and RCP8.5. The results of SDM indicate that the distribution of this species will move northward and have obviouse seasonal variations. Meanwhile, the suitable habitat for the species will be significantly reduced in summer, with loses rates ranging from 45.23% (RCP4.5) to 88.26% (RCP.8.5) by 2100s. Habitat reduction will mainly occur in the East China Sea and southern part of the Yellow Sea, while there will be a small increase in the northern Bohai Sea. These findings will be important to manage the ecosystem and fishery, provide an information forecast of this species in the future, and maintain species diversity if the seawater temperature rises.

This paper aims to show that sustainable behavior by firms may be impaired by regulatory restrictions. We challenge the assumption that regulation aimed at curbing greenhouse gas emissions (GHG) on the form of a target to meet the Country’s GHG emissions commitments will promote sustainable corporations. We argue that, in fact, such regulation may impair sustainability practices because it creates unintended consequences. This paper tackles the efficiency of the institutional framework chosen through the lenses of the analytical themes of fit, scale and interplay, then we use a systems dynamic approach to represent how regulation in the arenas of energy efficiency and GHG emissions reduction may withhold competitive business outcomes and corporate sustainability schemes. We exemplify and simulate a single regulation scheme and found that as a result of the institutional scheme chosen, the system is dominated by negative feedback processes resulting in lesser outcomes that would be better tackled by firms not being subject to the restrictions imposed by the regulation.

This study aims to reveal the revolutionary Gamma Distribution Manifold (GDM) info-geometric analysis combined with potential Gamma distribution (GD) applications to advance Satellite Earth Observations (SEOs). An exposition of the GDM Fisher Information Matrix (FIM) was undertaken, together with the analytic investigation of the existence of FIM’s inverse. The derivation of GDM’s Geodesic Equations (GEs) is undertaken. The solution of the obtained Geodesic Equations is optimally complicated, and it provides more extensions to numerous open problems. Notably, the current paper provides a first-time unification between three multi-interdisciplinary fields, namely, information geometry theory, probability theory, and Satellite earth observations. Looking at the other side of the coin, the provided revolutionary approach in this current work reports the significant impact of info-geometric analysis on the probabilistic dynamics as well as the influential role of information geometry on satellite and space industry. This poses numerous open issues that initiates a new form of contemporary unification between these inter-disciplinaries to discover another visionary thinking out of traditional statistical frames. In other words, refraining ourselves from using classical statistical frames of thinking and delving into a new info-geometric vision of statistical distributions as well as examining real life applications of information geometry to advance satellite earth observations. The curtain is drawn on this paper by providing several challenging open problems in combination with a concluding remark and the next phase of research.

This paper examines whether classical extensional mereology is adequate for formalizing the whole-parts relation in quantum chemical systems. Although other philosophers have argued that classical extensional and summative mereology does not adequately formalize whole-parts relation within organic wholes and social wholes, such critiques often assume that summative mereology is appropriate for formalizing the whole-parts relation in inorganic wholes such as atoms and molecules. However, my discussion of atoms and molecules as they are conceptualized in quantum chemistry will establish that standard mereology cannot adequately fulfill this task, since the properties and behavior of such wholes are context-dependent and cannot simply be reduced to the summative properties of their parts. To the extent that philosophers of chemistry have called for the development of an alternative mereology for quantum chemical systems, this paper ends by proposing behavioral mereology as a promising step in that direction. According to behavioral mereology, considerations of what constitutes a part of a whole is dependent upon the observable behavior displayed by these entities. Thus, relationality and context-dependence are stipulated from the outset and this makes behavioral mereology particularly well-suited as a mereology of quantum chemical wholes. The question of which mereology is appropriate for formalizing the whole-parts relation in quantum chemical systems is relevant to contemporary philosophy of chemistry, since this issue is related to the more general question of the reducibility of chemical wholes to their parts and of the reducibility of chemistry to physics, which have been of central importance within the philosophy of chemistry for several decades. More generally, this paper puts contemporary discussions of mereology within the philosophy of chemistry into a broader historical and philosophical context. In doing so, this paper also bridges the gap between formal mereology, conceived as a branch of formal ontology, and ‘applied’ mereology, conceived as a branch of philosophy of science.

Practically important properties of real liquids, including seawater, are their nonlinear properties, which include a nonlinear acoustic parameter, as well as cavitation strength – a rupture of the continuity of a liquid at high intensities in an acoustic wave. The manifestation of nonlinear effects is greatly facilitated by the presence of various nuclei in the liquid – gas bubbles, foreign particles, and other inclusions of various origins. For practical applications, it is important to study the properties of real liquids with inclusions in them. Due to the difficulties of measuring cavitation strength by acoustic methods, other methods are being sought. It is proposed to use an optoacoustic method associated with the use of laser radiation that causes optical breakdown - optical cavitation, that accompanied by a strong sound generation effect. The connection between optical breakdown thresholds and acoustic cavitation thresholds has been established, which can later be used to identify cavitation thresholds at high static pressures (at great depths in the sea), where the use of acoustic emitters is extremely difficult. The paper studies the bubble size distribution function in seawater, combined with studies of the acoustic nonlinearity parameter and cavitation strength at various depths. The interrelation of these characteristics for seawater is shown.

In this article we introduce an extension of the Akash distribution. We use the slash 1 methodology to make the kurtosis of the Akash distribution more flexible. We study the general 2 density of this new distribution, some properties, moments, coefficients of asymmetry and kurtosis. 3 Statistical inference is performed using the methods of moments and maximum likelihood via the 4 EM algorithm. A simulation study is carried out to observe the behavior of the maximum likelihood 5 estimator. An application to a real data set with high kurtosis is considered, where it is shown that 6 the new distribution fits better than other extensions of the Akash distribution.

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

Hepatitis C virus (HCV) causes both acute and chronic disease of the liver that can lead to liver cirrhosis, cancer and liver failure. HCV is characterized by high genetic diversity and substantial variations in prevalence of specific HCV genotypes in different countries of the world. Many effective regimens of direct-acting antivirals (DAAs), including pan-genotypic, can successfully treat HCV infection. However, genotype-specific treatments for HCV are being actively employed in the national plans for elimination of HCV infection around the world. Evaluation of HCV genotype prevalence in a country is mandatory for successful implementation of the national plans for elimination of HCV infection and allocation of financial resources to DAAs most effecting for specific HCV genotypes prevalent in a country. Here, we analyzed HCV genotypes, subgenotypes and recombinants in 10,107 serum samples from patients with chronic HCV infection from all Federal districts of Russia collected in 2015-2017. This is the first, largest evaluation of HCV genotypes performed on samples from all territories of Russia, from its Central Federal district to the Far East. Moreover, we have updated retrospective epidemiological analysis of chronic and acute HCV infection in Russia in 2001-2021. We demonstrate that the incidence of acute HCV infection in Russia reduced from 16.7 cases per 100,000 population in 2001 to 0.6 cases per 100,000 population in 2021. The number of cases of chronic HCV infection decreased from 29.5 to 16.4 per 100,000 population during this period. HCV genotype analysis indicated that HCV genotype 1 dominates in Russia (53.6%). Genotypes 3 and 2 were detected in 35.4% and 7.8% of patients respectively. These proportions are virtually identical in all regions of Russia except for Far East, where HCV genotype 2 amounts only to 1%. HCV genotypes 1 and 2 are more widespread in women, while HCV genotype 3 in men. The highest frequency of identification of genotype 3 was found in the age group of 31-40 years old (44.9%, respectively), and genotype 1 was more prevalent in a group of over 70 years old (72.2%). The proportion of HCV genotype 2 is predominant among HCV-infected persons older than 40 years. Discriminating HCV genotype 2 and recombinant RF1_2k/1b, which are frequently misclassified, is important for successful antiviral treatment of such patients. For the first time, we demonstrate the countrywide prevalence of HCV RF1_2k/1b in different regions of Russia. HCV RF1_2k/1b amounts to 3.2% in the structure of HCV genotypes, reaching 30% among samples classified as genotype 2 by some commercial genotyping tests. The highest proportion of HCV RF1_2k/1b was detected in the north-west (60%), southern (41.6%) and central (31.6%) federal district. Its frequency in Far Eastern and North Caucasus Districts was ~ 14.3%. HCV RF1_2k/1b was not detected in the Volga, Ural and Siberian districts. To conclude, this is the first and most complete evaluation of HCV epidemiology and genotype/subgenotype distribution in Russia.

Ticks drive a wide diversity of pathogens to a great variety of hosts, including humans. We conducted a tick surveillance study in northwestern Spain between 2014 and 2019. Ticks were removed from people and were identified. Tick numbers, species, development stages, evolution over time, seasonal and geographical distribution, and epidemiological characteristics of people bitten by ticks were studied. We collected ticks from 8143 people. Nymphs of Ixodes ricinus were the most frequently collected. Rhipicephalus bursa, Rhipicephalus sanguineus sensu lato (s.l), Hyalomma marginatum, Hyalomma lusitanicum, Dermacentor marginatus, Dermacentor reticulatus and Haemaphysalis punctata were also found, with adults as the main stage. Hyalomma spp. and R. bursa have been progressively increasing over time. Although bites occurred throughout the year, the highest number of incidents were reported from April to July. The distribution patterns of the tick species were different between the north and the south of the region, which was related to cases detected in humans of the pathogens they carried. Adult men were more likely to be bitten by ticks than women. Ticks were most frequently removed from adults from the lower limbs, while for children they were mainly attached to the head. Epidemiological surveillance is essential given the increase in tick populations in recent years, mainly of species potentially carrying pathogens causing emerging diseases in Spain, such as the Crimean Congo Hemorraghic Fever (CCFH).

The power function distribution is a flexible waiting time model that may provide better fit for some failure data. This paper presents the comparison of the maximum likelihood estimates and the Bayes estimates of two-parameter power function distribution. The Bayes estimates are obtained, using conjugate priors, under five loss functions consist of square error, precautionary, weighted, LINEX and DeGroot loss function. The Gibbs sampling algorithm is proposed to generate samples from posterior distributions and in result the Bayes estimates are computed. The comparison of the maximum likelihood estimates and the Bayes estimates are done through the root mean squared errors. One real-life data set is analyzed to illustrate the evaluation of proposed methods of estimation. Finally, results from the simulation are discussed to assess the performance behavior of the maximum likelihood estimates and the Bayes estimates.

A new discrete distribution for count data called extended biparametric Waring (EBW) distribution is developed. Its name is related to the fact that, in a specific configuration of its parameters, it can be seen as a biparametric version of the univariate generalized Waring (UGW) distribution, a well-known model for the variance decomposition into three components: randomness, liability and proneness. Unlike the UGW distribution, the EBW can model both overdispersed and underdispersed data sets. In fact, the EBW distribution is a particular case of a UWG distribution when its first parameter is positive; otherwise, it is a particular case of a Complex Triparametric Pearson (CTP) distribution. Hence, this new model inherits most of their properties and, moreover, it helps to solve the identification problem in the variance components of the UGW model. We compare the EBW with the UGW by a simulation study, but also with other over and underdispersed distributions through the Kullback-Leibler divergence. Additionally, we have carried out a simulation study in order to analyse the properties of the maximum likelihood parameter estimates. Finally, some application examples are included which show that the proposed model provides similar or even better results than other models, but with fewer parameters.