In current transportation hubs, it is a common phenomenon that passengers travel with necessary wheeled-luggage or suitcases. Due to the fact that most luggage occupies certain space within dense passenger crowds with giant mass inertia, its abnormal motions, such as drifting, frequently trig unavoidable local disturbances and turbulence in surrounding pedestrian flows, further increasing security risk. While, current researches primarily concentrate on examining the impact of luggage on crowd evacuation efficiency through scenario-based experiments and analyzing the spatial characteristics of crowd distribution in surveillance videos. There still lacks of the dynamic disturbance mechanisms and crowd stability associated with the combined motion of passengers and luggage. Therefore, this study considers the luggage-laden passenger as a deformable particle, the resulting disturbance on surrounding non-luggage passengers is analyzed and quantified into a nonlinear pressure term. Subsequently, the disturbance propagation model of passenger-luggage is developed by adapting the classical Aw-Rascle traffic flow model with incorporation of the pressure term. Simulation experiments of disturbances caused by luggage drifting and retrograding validate that the proposed propagation model aligns with real-world situations in transportation hubs. Quantitively, when luggage-laden passenger drifted left, the disturbing force of left side crowd can reach a peak of 238N in the passenger density of 3.0 p/m2, and the maximum difference between the left and right sides disturbing force can reach 153N. Furthermore, it is recommended that the proposed model can be applied to crowd flow analysis and risk assessment.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Infrared thermography has already been proven to be a significant method in non-destructive evaluation since it gives information with immediacy, rapidity and low cost. However, the thorniest issue for wider application of IRT is the quantification. In this work, we proposed a specific depth quantifying technique by employing the Gated Recurrent Units (GRU) in composite material samples via pulsed thermography (PT). Carbon Fiber Reinforced Polymer(CFRP) embedded with flat bottom holes were designed via Finite Element Method (FEM) modeling in order to precisely control the depth and geometrics of the defects. The GRU model automatically quantified the depth of defects presented in the CFRP material. The proposed method evaluated the accuracy and performance of synthetic CFRP data from FEM for defect depth predictions.

Recovery of forest after logging can be tested in many ways: the presence of particular species of fauna or flora, the similarity of the biodiversity of the recovering forest to that on neighbouring areas of undisturbed forest; or the characteristics of soils and streams whose conditions may have drastically changed during logging. Three cases of rainforest recovery after logging and clearance from Australia and Borneo exhibit different starting and different goals for recovery. Faunal indicators of recovery vary with size and with species dependence of the rainforest. Endemic forest species may have difficulty in recovering. Tree species richness and abundance may recover in two decades, but canopy closure takes longer. Compacted soils may retain low infiltration capacities for many decades. This diversity in recovery rates is confirmed when compared with those used elsewhere. Because the starting points for recovery vary, from damage by tropical cyclones and landslides, to clearance for shifting cultivation, pasture or agriculture, to post-logging conditions, universal indicators may be inappropriate. The desired endpoints of recovery also range from a “wilderness” state to a National Park for human enjoyment, biodiversity preservation, safeguarding rights of traditional forest-dwelling peoples, or a second round of selective logging.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Noise reduction is the major issue in the loudspeaker for the application of the musical instruments and related areas. In this paper, a noise disturbance control of a loudspeaker with optimal and robust controllers has been done successfully. The noise of the loudspeaker has been analyzed by simply track a reference cone displacement with the actual cone displacement. Static output feedback and H infinity optimal loop shaping controllers have been used to compare the actual and reference cone displacements by using a sine wave and random cone displacement signals and a promising results have been analyzed.

Intelligent ship technology is currently an international research hotspot, and model predictive control is widely used in the path-tracking control of intelligent vehicles. To construct an intelligent ship anti-disturbance path-tracking control method, firstly, an environmental disturbance model was constructed with the actual meteorological data of the target sea area. Secondly, the Fossen ship equation of motion is linearized and discretized as the ship motion model. Thirdly, the expression of the prediction equation is derived from the ship motion model. Fourthly, the cost function is constructed by using the polar diameter and polar angle values of the ship. Fifth, the power function in the cost function is replaced with an exponential function to obtain an improved cost function. Sixthly, according to the Lyapunov theory and the MPC terminal constraint theory, the stability of the improved cost function is verified. Seventh, different test paths are set up, the environmental disturbance model is taken as the external disturbance, the ship motion model, the prediction equation, and the improved cost function are used to design the anti-disturbance path-tracking control algorithm according to the model prediction control idea for simulation experiments. Finally, different MATLAB simulation results show that the improved cost function can resist disturbance of the external wave, current, and wind, and effectively track the target path. Therefore, this study provides a reference for improving the navigation safety of ship path-tracking.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

The main objective of this work is the assessment of the annual number of hospital admissions for respiratory disease (HARD) due to the exposure to in-healable particulate matter (PM10), within the greater Athens area (GAA), Greece. Towards this aim, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) recorded in six monitoring stations located in the GAA, for a 13-year period 2001-2013, is used. Initially, a descriptive statistical treatment of PM10 concentrations took place. Furthermore, the AirQ2.2.3 software developed by the WHO was used to evaluate adverse health effects by PM10 in the GAA during the examined period. The results show that, during the examined period PM10 concentrations present a significant decreasing trend. Also, the mean annual HARD cases per 100,000 inhabitants ranged between 20 (suburban location) and 40 (city centre location). Approximately 70% of the annual HARD cases are due to city centre residents. In all examined locations, a declining trend in the annual number of HARD cases is appeared. Moreover, a strong relation between the annual number of HARD cases and the annual number of days exceeding the European Union daily PM10 threshold value was found.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

Brucellosis is a multi-system infectious disease that exhibits with various manifestations and complications. Neurobrucellosis is a rare but serious presentation of brucellosis that can be discovered in every stages of the disease. Laboratory tests and physical examination and patient history are generally the basis for diagnosing the disease. It has both insidious and prolonged clinical course of the disease and long-term therapies. Also the most common pattern of exhibition is subacute or chronic. We reported a case of young female who had history of painless weakness in the right lower limb (proximal and distal) that started gradually and had progressed over the time, and after a month she felt weakness in the left lower limb with the same pattern. Lumbosacral Magnetic resonance imaging (MRI) with and without contrast was shown evidence of enhancement thickening of caudal equina ventral roots. Brucella antigen titer was positive, the result was 1/160. And other clinical tests were normal. Patient treated with Intravenous injection (IV) Rifampicin and Intravenous Cotrimoxazole. patient was discharged with good health and continuinng all two medications for 5 months. The descision was taken to report this case as a result of entire respond in patient’s illness after a enduring disease. Neurobrucellosis is a treatable disease in which it would be better to consider a high indication of suspicion. Due to if ignored, it may cause significant morbidity and mortality.

Remote sensing datasets are increasingly being used to provide spatially explicit large scale evapotranspiration (ET) estimates. The focus of this study was to estimate and thematically map on a pixel-by-pixel basis, the actual evapotranspiration (ET_a) of the Wonji Shoa Sugarcane Estate using the Surface Energy Balance Algorithm for Land (SEBAL), Simplified Surface Energy Balance (SSEB) and Operational Simplified Surface Energy Balance (SSEBop) algorithms. The results obtained revealed that the ranges of the daily ETa estimated on January 25, February 26, September 06 and October 08, 2002 using SEBAL were 0.0 - 6.85, 0.0 – 9.36, 0.0 – 3.61, 0.0 – 6.83 mm/day; using SSEB 0.0 - 6.78, 0.0 – 7.81, 0.0 – 3.65, 0.0 – 6.46 mm/day, and SSEBop were 0.05 - 8.25, 0.0 – 8.82, 0.2 – 4.0, 0.0 – 7.40 mm/day, respectively. The Root Mean Square Error (RMSE) values between SSEB and SEBAL, SSEBop and SEBAL, and SSEB and SSEBop were 0.548, 0.548, and 0.99 for January 25, 2002; 0.739, 0.753, and 0.994 for February 26, 2002;0.847, 0.846, and 0.999 for September 06, 2002; 0.573, 0.573, and 1.00 for October 08, 2002, respectively. The standard deviation of ET_a over the sugarcane estate showed high spatio-temporal variability perhaps due to soil moisture variability and surface cover. The three algorithm results showed that well watered sugarcane fields in the mid-season growing stage of the crop had higher ET_a values compared with the other dry agricultural fields confirming that they consumptively use more water. Generally during the dry season, ET_a is limited to water surplus areas only and in wet season, ET_a was high throughout the entire sugarcane estate. The evaporation fraction (ETrF) results also followed the same pattern as the daily ET_a over the sugarcane estate. The total crop and irrigation water requirement and effective rainfall estimated using the Cropwat model were 2468.8, 2061.6 and 423.8 mm/yr for January 2001 planted and 2281.9, 1851.0 and 437.8 mm/yr for March 2001 planted sugarcanes, respectively. The mean annual ET_a estimated for the whole estate were 107 Mm³, 140 Mm³, and 178 Mm³ using SEBAL, SSEB, and SSEBop, respectively. Even though the algorithms should be validated through field observation, they have potential to be used for effective estimation of ET in the sugarcane estate.

Introduction: Hypertension is a serious public health problem in Morocco. The objective of this pilot study was to estimate the salt intake of Moroccan adults by measuring 24-hour urinary sodium excretion. Methods: 132 participants were recruited from the central region of Morocco. Sodium, potassium and creatinine levels were measured using the 24-hour urine samples. Additional data included anthropometric measurements and socio-demographic questionnaire. Results: The daily sodium, potassium and creatinine excretions were 2779.1±1334.9 mg, 1350.0±642.8 mg and 820.3 ± 381.2 mg, respectively. Data analysis revealed that 71.2% of the participants had a daily sodium intake more than 2000 mg (5g of salt) recommended by the WHO. The mean of potassium excretion was 1350.0±642.8 mg /day, this average was lower than 3.51g per day recommended by the WHO. Conclusion: Public health measures to reduce sodium and increase potassium consumption in order to decrease the population’s risk of high blood pressure and heart disease are recommended.

Tropical forest and savanna biomes are pivotal in the functioning of the Earth system. Tropical forests are one of the largest terrestrial biosphere carbon pools, whereas savannas exchange carbon between the biosphere and atmosphere via frequent and extensive landscape fires. Both are biodiverse and under increasing threat due to land clearing and anthropogenic climate change. Reliable mapping of tropical forest and savanna is essential to provide understanding of how anthropogenic impacts are affecting the extent of these biomes. Using Google Maps satellite imagery, we manually classified 24,239 random points as forest, savanna, or anthropogenic landscapes within the tropics. Because fire and climate are correlated, we developed separate geospatial models to rank the importance of climate, topography, and human influence on vegetation present. This modelling confirmed that those areas with more fires had lower probabilities of tropical forest, that forest was most likely in areas with high mean annual rainfall with little seasonal variation in precipitation, and that anthropogenic factors disrupt this environmental predictability. We found there were environments where tropical forest and savanna were equally probable are geographically restricted. These relationships suggest that future drier climates projected under anthropogenic climate change, combined with clearing and burning that have reduced tropical forest extent to a subset of its theoretical distribution, will lead to irreversible loss of tropical forests. Our modelling provides global mapping that can be used track further changes to distribution of rainforests.

The study of vegetation community and structural change has been central to ecology for over a century, yet how disturbances reshape the physical structure of forest canopies remains relatively unknown. Moderate severity disturbance including fire, ice storms, insect and pathogen outbreaks, affects different canopy strata and plant species, which may give rise to variable structural outcomes and ecological consequences. Terrestrial lidar (light detection and ranging) offers an unprecedented view of the interior arrangement and distribution of canopy elements, permitting the derivation of multidimensional measures of canopy structure that describe several canopy structural traits with known linkages to ecosystem functioning. We used lidar-derived canopy structural measured within a machine learning framework to detect and differentiate among various disturbance agents, including moderate severity fire, ice storm damage, age-related senescence, hemlock woolly adelgid, beech bark disease, and chronic acidification. We found that disturbance agents such as fire and ice storms primarily affected the amount and position of vegetation within canopies, while acidification, pathogen and insect infestation, and senescence altered canopy arrangement and complexity. Only two of the six disturbance agents significantly reduced leaf area, indicating that this commonly quantified canopy feature is insufficient to characterize many moderate severity disturbances. Rather, measures of canopy structure, including those that describe multidimensional change, are needed to characterize disturbance at moderate severities because structural changes from these events are spatially and quantitatively variable. Our findings suggest that standard disturbance detection methods, such as optical based remote sensing platforms, may currently be limited in their ability to detect, differentiate, and characterize disturbance. Further, we conclude that a more broadly inclusive definition of ecological disturbance that incorporates multiple aspects of canopy structure change will improve the modeling, detection, and prediction of functional implications of moderate severity disturbance.

Wildfires are important sources of landscape change in Mediterranean environments, creating large patches of natural habitats (i.e., scrublands) inside protected areas, whereas woodland patches remained at the border in the vicinity of human settlements. Landscape patterns resulting from these gradients influence habitat suitability for mesocarnivores regarding food and shelter. In winter and summer 2019, we sampled 16 independent line-transects of four camera traps each (for a total of 64 cameras), covering the main habitats of the study area (woodlands, scrublands, and crops). Cameras were baited to compensate for low detectability of target species, and mesocarnivore contacts were analyzed by means of GLMMs and occupancy models. We hypothesized that Mediterranean mesocarnivores were constrained by two opposing forces, pushing them living in semi-natural but highly fragmented and heterogeneous landscapes created by humans, or living in natural but less suitable and continuous habitats created by fire regimes. In the former case, mesocarnivores will find protection against predators and resting sites in forests, as well as improved food opportunities in crops and urban areas, despite the possible interference with humans and their pets. Potential cascading effects linked to ecological roles of Mediterranean mesocarnivores on the succession of Mediterranean landscapes would imply longer-term effects of human disturbance on landscape trends.

With the progression of AI, embedding advanced AI technologies into small robotics and mobile devices has become essential, driving research towards lightweighting AI models. Our study enhances the EPINET depth estimation model for light field images, aiming for compactness and faster inference while preserving accuracy. We conducted two-step experiments aimed at enhancing inference efficiency: Initially, by adjusting input streams and convolution layers, we simplified the CNN model, achieving faster inference times at the cost of reduced accuracy. To address this reduction in accuracy, we then applied knowledge distillation, allowing the simplified model to learn from the original model’s more complex patterns. In our quantitative experiments using two error metrics, MSE (Mean Squared Error) and BadPix, we identified optimal knowledge positions and evaluated the required complexity for the student model. As a result, our method improved MSE by 21% and BadPix by 14% compared to training without it. Furthermore, the student model achieved an inference speed 13% faster than the teacher model and surpassed its accuracy by 10% in MSE. Additionally, we demonstrated that repeatedly applying our approach could further enhance both model compactness and accuracy.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

This paper presents an approach to improve the robustness of tip-tilt controllers for fast-steering mirror (FSM)-based laser beam steering (LBS) systems in the presence of dynamic disturbances such as external shocks. To this end, we propose the addition of a disturbance observer (DOB)-based anti-shock controller in parallel to the original linear servo control loop to improve its control performance in the presence of external shocks. To increase the tip-tilt control performance against external shocks, the DOB-based control method, which is an improved control method for eliminating nonperiodic disturbances, is implemented in the original tip-tilt control system. Results indicate that the control error of the DOB-based anti-shock controller decreased, resulting in an efficient improvement in its disturbance-rejection performance.

Stratified Taylor Couette Flow (STCF) undergoes transient growth. Recent studies have shown that there exists transient amplification in the linear regime of counter-rotating STCF. It is reported that as Gr increases, the maximum amplification factor ($G_0$) initially decays before it eventually starts growing after reaching a certain critical value Gr$_{c}$. Assuming other parameters of the model are kept constant, the value Gr$_{c}$ changes with respect to different speed ratios of the cylinders. The observed decay/growth pattern of $G_0$ is attributed to the interplay between the induced shear and buoyancy. In this study, the mechanism that triggers this observed pattern is investigated. The kinetic budget of the optimal transient perturbation is analysed numerically to simulate the interaction of the shear production (SP), buoyancy production (BP) and other energy components that contributes to the total optimal transient kinetic energy. These contributions affect the total energy by influencing the perturbation to extract kinetic energy (KE) from the mean flow. The decay of $G_0$ resulted from the positive amplification of both BP and SP, while the growth is attributed to the negative and positive amplification of BP and SP, respectively. The optimal SP is positively amplified, implying that there is the possibility of constant linear growth. These findings agree with the linear growth rate for increasing values of Gr.

We designed a novel growth controller regulated by feeding of an unnatural amino acid, Nε-benzyloxycarbonyl-L-lysine (ZK), using a specific incorporation system at a sense codon. This system is constructed by a pair of modified pyrrolisyl-tRNA synthetase (PylRS) and its cognate tRNA (tRNApyl). Although ZK is non-toxic for normal organisms, the growth of Escherichia coli carrying the ZK incorporation system was inhibited in a ZK concentration-dependent manner without causing rapid bacterial death, presumably due to generation of non-functional or toxic proteins. The extent of growth inhibition strongly depended on the anticodon sequence of the tRNApyl gene. Taking advantage of the low selectivity of PylRS for tRNApyl anticodons, we experimentally determined the most effective anticodon sequence among all 64 nucleotide sequences in the anticodon region of tRNApyl gene. The results suggest that the ZK-regulated growth controller is a simple, target-specific, environmental noise-resistant and titratable system. This technique may be applicable to a wide variety of organisms because the growth inhibitory effects are caused by “informational disturbance”, in which the highly conserved system for transmission of information from DNA to proteins is perturbed.

Forest managers are often required to restore forest stands following natural disturbances, a situation that may become more common and more challenging under global change. In parts of Central Europe, particularly in mountain regions dominated by mixed temperate forests, the use of relatively low intensity, uneven-aged silviculture is a common management approach. Because this type of management is based on mimicking less intense disturbances, the restoration of more severe disturbance patches within forested landscapes has received little attention within the context of uneven-aged silviculture in the region. The goal of this paper is to synthesize research on the restoration of forests damaged by disturbances in temperate forests of Slovenia and neighbouring regions of Central Europe, where uneven-aged silviculture is practiced. We place particular emphasis on the most important biotic and abiotic drivers of post-disturbance regeneration, and use this information to inform silvicultural decisions about applying natural or artificial regeneration in disturbed areas. We conclude with guidelines for restoration silviculture in uneven-aged forest landscapes.

Forest ecosystems make a greater contribution to carbon (C) stocks than any other terrestrial ecosystem. To understand the role of regional forest ecosystems in global climate change and carbon exchange, forest C stock and its spatial distribution within the small (2,300 km2) Liuxihe River basin were analyzed to determine the different contributors to the C stock. Forest C stocks were quantified by measuring the biomass of trees, understory vegetation, litter and roots, as well as soil organic C, using data from field samples and laboratory experiments. The results showed that forests stored 38.04 Tg C in the entire basin, with secondary and planted forests accounting for 89.82% and 10.18%, respectively, of the stored C. Five types of forests, a subtropical evergreen broad-leaved forest, a subtropical coniferous and broad-leaved mixed forest, a subtropical coniferous forest, a timber forest, and a non-wood forest, stored 257.55 ± 15.01, 218.92 ± 9.59, 195.24 ± 18.29, 177.42 ± 17.55, and 117.86 ± 6.04 Mg C ha−1, respectively. In the forest ecosystem C stocks of the basin, soils averagely contribute about 73.78%, not including root underground biomass. It provides a comprehensive method for forest ecosystem carbon investigation and forest management in small basin scale.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

The robust control of high precision electromechanical systems, such as micropositioners, is challenging in terms of the inherent high nonlinearity, the sensitivity to external interference, and the complexity of accurate identification of the model parameters. To cope with these problems, this work investigates a disturbance observer-based deep reinforcement learning control strategy to realize high robustness and precise tracking performance. Reinforcement learning has shown great potential as optimal control scheme, however, its application in micropositioning systems is still rare. Therefore, embedded with the integral differential compensator (ID), deep deterministic policy gradient (DDPG) is utilized in this work with the ability to not only decrease the state error but also improves the transient response speed. In addition, an adaptive sliding mode disturbance observer (ASMDO) is proposed to further eliminate the collective effect caused by the lumped disturbances. The sterling performance is revealed with intensive tracking simulation experiments and demonstrates the improvement in the accuracy and response time of the controller.

The Fruit Harvest Helper, a mobile application developed by Northwest Nazarene University’s (NNU) Robotics Vision Lab, aims to assist farmers in estimating fruit yield for apple orchards. Currently, farmers manually estimate the fruit yield for an orchard, which is a laborious task. Fruit Harvest Helper seeks to simplify their process. While prior research efforts at NNU concentrated on developing an iOS app for blossom detection, this current research aims to adapt that smart farming application for apple detection across multiple platforms, iOS and Android. The old and new applications were designed with an intuitive user interface that is easy for farmers to use, allowing for quick image selection and processing. Unlike before, the adapted app utilizes a color ratio-based image segmentation algorithm implemented in OpenCV C++ to detect apples in apple tree images selected for processing. The results of testing the algorithm with a dataset of images indicate an 8.52% Mean Absolute Percentage Error (MAPE) and a Pearson correlation coefficient of 0.6 between detected and actual apples on the trees. These findings were obtained by evaluating the images from both the east and west sides of the trees, which was the best method to reduce the error of this algorithm. Although the Fruit Harvest Helper shows promise, there are many opportunities for improvement. These opportunities include exploring alternative machine-learning approaches for apple detection, conducting real-world testing without any human assistance, and expanding the app to detect various types of fruit. The Fruit Harvest Helper mobile application is among the many mobile applications contributing to precision agriculture, nearing readiness for farmers to use in yield monitoring and farm management.

In recent decades, large-scale forest disturbances such as windthrow and bark beetle infestations have significantly impacted the carbon balance of Earth and forest ecosystems, mainly by altering soil respiration (SR) in addition to decreased gross primary productivity. SR is considered the second highest flux on Earth, emitting 78-98 Gt C yr-1 to the atmosphere, thus contributing to global warming. Post-disturbance development is marked by changes in the size of SR. To investigate the impact of bark beetle (Ips typographus) infestations in mountain spruce forests on SR, we measured SR at infested sites by bark beetles and adjacent undisturbed stands in the High Tatra Mountains (Slovakia). The measurements were conducted during the vegetation period (May-September) in 2016 and 2017, five to six years after the initial attack by bark beetles, at an altitudinal gradient (1100-1400 m a.s.l.). SR varied throughout different months and altitudes, and we observed that SR at infested sites reached higher values (in most cases) than at uninfested stands. Average monthly and altitude SR rates during both vegetation periods showed higher values at infested sites, but not all of them were statistically significant. We observed an insignificant change in SR rate between 2016 and 2017 at both infested and uninfested sites. The highest rates of SR were observed in 2016 from July to August at both infested and undisturbed sites. On the other hand, in 2017 the highest SR rates were observed in June and July at undisturbed sites and from June to August at infested sites. However, yearly SR from May-September at infested sites showed significantly higher rates than uninfested ones in both years. SR showed a decreasing pattern with elevation gain in 2016 at infested sites. However, this pattern was not observed in 2017. Based on our observation and results we postulate that SR rates at infested sites are boosted by needle fall and debris from dead and dying trees, which increases heterotrophic SR and compensates the decrease of autotrophic SR from tree roots. This study provides important insights into the impact of bark beetle infestations on SR and highlights the need for further research on the long-term effects of forest disturbances on carbon cycling.

This work focuses on addressing the dynamic positioning and trajectory tracking problem for a 4 degree-of-freedom (DOF) unmanned underwater vehicle (UUV) in the presence of nonlinear dynamics, parametric uncertainties, system constraints, and time-varying external disturbances. To tackle this problem, a disturbance observer-based control (DOBC) scheme is proposed. The scheme is structured around the model predictive control (MPC) method integrated with an extended active observer (EAOB). Compared to the conventional disturbance observer, the EAOB has the unique ability to handle both external disturbances and system/measurement noises simultaneously. The EAOB leverages a combination of sensor measurements and a system dynamic model to estimate disturbances in real-time, which allows continuous estimation and compensation of time-varying disturbances back to the controller. The proposed disturbance observer-based MPC (DOBMPC) is implemented by feeding the estimated disturbances back into the MPC’s prediction model, which forms a robust adaptive controller with a parameter-varying model. The proposed control strategy is validated through simulations in a Gazebo and Robot Operating System (ROS) environment. The results show that it can effectively reject unpredictable disturbances and improve the UUV’s control performance.

This paper has the objective of implementing the radial rotor position control of a three-phase bearingless induction machine with split winding and optimized drive structure, using the ADRC technique. Because it is a multivariable, nonlinear, time-varying system with coupled variables, it is necessary to use advanced control strategies in order for the system to operate efficiently and with good dynamic performance. The ADRC controller considers the total disturbance composed of unmodeled dynamics, nonlinearities, uncertainties, and load variations, as a new system state, to be estimated in real-time through an extended state observer. In this mode, disturbances are compensated in real-time, eliminating regime errors and with good response to disturbances in general.

This data descriptor summarizes the process applied to identify, screen, select and gather data from the content of 142 peer-reviewed papers/sources that report on the sources and impacts of recreational disturbance on coastal avifauna. While populations of resident and migratory coastal avifauna are under threat and diminishing rapidly across the planet, and particularly in association with Asian flyways, many governments are leveraging booming global demand for coastal recreation and tourism in order to deliver economic development to regional communities. The summary data shared via this data description was extracted from papers collected in a systematic literature review that was designed to explore the global literature on the recreational disturbance of coastal avifauna in order to elucidate the state of the global knowledge regarding this issue and to identify management strategies that could be applied at tropical Asian destinations to minimize the impacts of recreational disturbance and thus enhance the ecological sustainability of coastal recreation and tourism across the region. The data shared via the Excel worksheet associated with this data descriptor was extracted from peer-reviewed articles published in English between 1 January 2000 and the 31 December 2018 with the full text of the article available online. These articles were found by searching several online indexing several databases including Scopus, Web of Science, ProQuest and Google Scholar.

With the increasing demand for precise condition monitoring and diagnosis of gas-insulated switchgears (GIS), it has become a challenge to improve the detection sensitivity of partial discharge (PD) induced in the GIS spacer. This paper deals with the elimination of the capacitive component from the phase resolved partial discharge (PRPD) signal generated in GIS spacer based on the discrete wavelet transform. Three types of typical insulation defects were simulated using PD cells. The single PD pulses were detected and were further used to determine the optimal mother wavelet. As a result, the bior6.8 was selected to decompose the PD signal into 8 levels and the signal energy at each level was calculated. The decomposed components related with capacitive disturbance were discarded whereas those associated with PD were de-noised by a threshold and a thresholding function. Finally, the PRPD signals were reconstructed using the de-noised components.

Forest vegetation dynamics (succession and dominance) is an ecological phenomenon that is still difficult to characterize and integrate into management practices. In this study, the understanding of forest dynamics is explored based on Grime’s theoretical triangular model of plant adaptive strategies using the example of Lithuania’s forest ecosystems. The idea behind this is the hypothesis that forest dynamics is linked to natural selection as an evolutionary process that exhibits differential species responses to competition, stress, and disturbance. The aim of this study is to explore the adaptive relationships in hemi-boreal forests. Grime’s and Pierce’s secondary CSR strategies, which describe various equilibria between competitiveness (C), stress tolerance (S), and ruderalism (R), were considered to reflect four establishment and development adaptive specialization characteristics of forest tree species. As a result of the study, four types of tree functional groups were identified: stress-resistant ruderals, competitive stress-sensitive ruderals, ruderal stress-sensitive competitors, and stress-resistant competitors. Based on this, we propose that reforestation move away from single species regeneration by implementing the maintenance of these four types of functional groups. In conclusion, forest management must consider the existence of the established equilibria between plant competitiveness, stress tolerance, and ruderalism. The formal concepts presented in this article can serve as a guide for future relevant research and development of appropriate methods for studying real forests. This study is unique in that no previous work has linked forest dynamics and natural selection in the context of Lithuania’s forest ecosystems.

The Internet use has become an integral part of daily life, adolescents are especially at a higher risk to develop problematic Internet use (PIU). Although one of the most well-known comorbid conditions of PIU is sleep disturbance, little is known about the sex disparity in this association. This school-based survey in students of grades 7-9 was conducted to estimate the prevalence of PIU and sleep disturbance among Chinese adolescents, to test the association between PIU and sleep disturbance, and to investigate the role of the child’s sex in this association. A two-stage stratified cluster sampling method was used to recruit participants, and a two-level logistic regression models were fitted. The mean Internet addiction test scores was 37.2 (SD: 13.2), and 15.5% (736) met the criteria for PIU. After adjusting for control variables, problematic Internet users were at a higher risk of sleep disturbance (adjusted odds ratio=2.41, 95% CI=2.07-3.19). Sex-stratified analyses also demonstrated that association was greater in girls than boys. In this respect, paying more attention to the sleep patterns of adolescents who report excessive Internet use is recommended, and this early identification may be of practical importance for schools, parents, and adolescents themselves.

Eutrophication, a global concern, impacts water quality, ecosystems, and human health. It’s crucial to monitor algal blooms in freshwater reservoirs, as they indicate the trophic condition of a waterbody through Chlorophyll-a (Chla) concentration. Traditional monitoring methods, however, are expen-sive and time-consuming. Addressing this hindrance, we developed models using remotely sensed data from the Sentinel-2 satellite for large-scale coverage, including its bands and spectral indexes, to estimate the Chla concentration on 149 freshwater reservoirs in Ceará, Brazil. Several machine learning models were trained and tested, including k-nearest neighbours, random forests, extreme gradient boosting, the least absolute shrinkage, group method of data handling (GMDH), and sup-port vector machine models. A stepwise approach determined the best subset of input parameters. Using a 70/30 split for the training and testing datasets, the best-performing model was the GMDH, achieving an R2 of 0.91, MAPE of 102.34%, and RMSE of 20.38 g/L, which are values consistent with the ones found in the literature. Nevertheless, the predicted Chla concentration values were most sensitive to the red, green, and near infra-red bands.

In this paper, to make the missile intercept the maneuvering target, the parallel approaching guidance law is developed. In order to estimate the target maneuver more accurately and reduce that’s influence on guidance accuracy, the distance-scalar disturbance observer is employed. Specifically, the estimation accuracy of the observer designed is regardless of the relative distance. The finite-time prescribed performance is employed to ensure that the line-of-sight angular rate is capable of converging to a predesigned small region in the specified finite time. All signals of interception system can guarantee ultimately uniformly boundedness proved by the Lyapunov stability theory. Finally, the availability of the parallel approaching guidance law is demonstrated by the numerical simulation.

The motion of Unmanned Surface Vehicles (USVs) is frequently disturbed by the ocean wind, wave and current. A poorly designed controller will lead to failures and even safety problems during actual navigation. In order to obtain satisfied control performance of the motion for the USVs, a Model Predictive Control (MPC) based on improved Nonlinear Disturbance Observer (NDO) is proposed. Firstly, the USV model is approximately linearized and MPC is designed for the multivariable system with constraints. In order to compensate the influence of disturbances, an improved NDO is designed, with which the calculation time for the MPC saved a lot. Finally, comparison experiments are conducted between the MPC with NDO and the MPC with improved NDO, and the results show that they have similar performance to the USVs. However, the proposed method has less parameter to be tuned and it is much more time-saving compared to the MPC with traditional NDO.

In many previous studies, the conclusions for the effects of disturbance and environmental gradients on the diversity was remain controversial due to exclusions of trait-based diversity in their methodology. This study hypothesized trait-based indices are more likely to show monotonic and predictable relations than traditional based species diversity to guide effective restoration of tree species diversity against environmental change and anthropogenic factors. This study therefore, was initiated to access trait based functional diversity of Yayu Coffee Forest Biosphere Reserve (YCFBR), Southwest Ethiopia. Data was collected from 90 proportionally distributed plots along disturbance levels from core, buffer and transitional zones. For functional trait diversity estimation, traits relevant to plant-life strategy, competition and response to disturbances and climate change were selected. Multiple regression model was used to test the response of species diversity and functional diversity to disturbance and environmental gradients. The result revealed that, anthropogenic disturbance and elevational gradients are the most important factors influencing functional diversity in the YCFBR. Overall this study demonstrates that, trait based functional diversity is useful to predict adaptation potentials of species in heterogeneous environments. Species with low specific leaf area & selective seed mass is recommended for the restoration of disturbed ecosystem.

Time estimation was investigated in 24 healthy adults, 12 women and 12 men, before and after an exhaustive exercise. We compared the capability of estimating time intervals in the range from 1 to 5 s using tasks requiring mental count and tasks that did not allow the mental count. Time estimation and blood lactate levels were evaluated before and at the end of the exercise. We found that the perception of time intervals between 1 and 5 s was affected at the end of the exercise. The observed effects, associated with a significant increase in blood lactate levels, were different in the two types of time estimation used in the present study. In experimental conditions in which participants had to evaluate duration of the time interval by mental counting, at the end of exercise a significant reduction in the overestimation of time made at rest was observed. On the other hand, when participants had to assess the difference in duration between two events without the possibility to mentally count, at the end of the exercise a significant deterioration in performance was observed. In both cases, no gender differences were seen.

Retinal vein cannulation involves puncturing an occluded vessel on the micron scale. Even single millinewton force can cause permanent damage. An ophthalmic robot with a piezo-driven injector is precious enough to perform this delicate procedure, but the uncertain viscoelastic characteristics of the vessel makes it difficult to achieve the desired contact force without harming the retina. The paper utilizes a viscoelastic contact model to explain the mechanical characteristics of retinal blood vessels in order to tackle this issue. The uncertainty in the viscoelastic properties is considered an internal disturbance of the contact model, and an active disturbance rejection controller is then proposed to precisely control the contact force. The experimental results show that this method can precisely adjust the contact force at the millinewton level even when the viscoelastic parameters vary significantly (up to 403.8%). The root mean square (RMS) and maximum value of steady-state error are 0.32 mN and 0.41 mN. The response time below 2.51 s with no obvious overshoot.

Vibrations of blades and tower have important impact for wind turbine. This paper presents a active controller design to suppress blade edgewise vibrations under aerodynamic load and gravitational load.Treating the sum of aerodynamic load input in edgewise direction and gravitational load as unknown disturbance input,a stochastic disturbance accommodating control(SDAC) approach is proposed to design a controller which it utilizes a minimum-variance unbiased estimator(MVUE) to estimate both state and unknown input. The stability analysis proved that the proposed SDAC is bounded in mean square.In order to verify the performance of the minimum-variance unbiased estimator and the proposed SDAC, numerical simulations using Matlab/Simulink have been carried out for the National Renewable Energy Laboratory 5-MW wind turbine.Under the different circumstance which exists the random process and measure noise and noise free. It is shown that the estimation value by MVUE can tracking the real state and unknown input. The results are also compared to the traditional linear quadratic regulator(LQR) and show that the proposed stochastic disturbance accommodating control scheme can further reduce displacement in edgewise vibrations direction and the control strategy is more effective than the LQR.

1) Landsat operational land imager (OLI) data and consequent laboratory measurements were used to predict Chlorophyll-a (Chl-a) concentration and the trophic states for an inland lake within the East Kolkata Wetland, India; 2) The most suitable band ratio was identified by performing Pearson correlation analysis between Chl-a concentrations and possible OLI band and band ratios from the study points; 3) The results showed highest correlation coefficient from the band ratio OLI5/OLI4 with an R value of 0.85. The prediction model was then developed by applying regression analysis between the band ratio OLI5/OLI4 and Chl-a concentration of the study points. The reflectance ratios of the validation points were given as input on the prediction model and the model output was considered as predicted Chl-a values of the validation points to check the efficiency of the prediction model. The regression model between laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points revealed a high correlation with an R² value of 0.78. Trophic State Index (TSI) of the lake was also calculated from laboratory-derived Chl-a value and model-fitted Chl-a value of the validation points. The study presented a high correlation of TSI determined from predicted data with TSI from laboratory reference data (R = 0.88). The TSI values of the lake ranged from 65 to 75 which indicate that the lake is appeared to be eutrophic to hypereutrophic conditions. 4) This empirical study showed that Landsat 8 OLI imagery can be effectively applied to estimate Chl-a levels and trophic states for inland lakes.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

Wireless communication has proliferated due to the colossal augmentation of smart phones, mobile phones, tablets and laptops etc. Multimedia applications such as live videos, audios, still images, animated graphics and live communications all requires accompaniments of quality of service (QoS) as well as reliable end-to-end transfer of data. Information about the availability of resources in channel is must in order to improve the QoS. QoS can be determined in terms of capacity of channel, available bandwidth (ABW), and bulk transfer capacity (BTC). Bandwidth availability is a key check for improving the QoS in a network. The performance of a multimedia application is directly affected by the bandwidth availability. One of the most important QoS characteristic is ABW at a wireless route and it can be demarcated as least unused capacity of links instituting a network route. Since now there have been many bandwidth estimation techniques are available in the literature to increase the network performance. Bandwidth estimation techniques have been arranged into three leading classifications: i) Active probing bandwidth estimation techniques, ii) Passive bandwidth estimation technique and iii) Model based bandwidth estimation techniques. Each of these techniques are briefly discussed in this paper.

The stock beta coefficient literature extensively discusses the proper methods for the estimation of beta as well as its use in asset valuation. However, there are relatively few references with respect to the appropriate time horizon that investors should utilize when evaluating the risk-return relationship of a stock. We examine the appropriate time horizon for beta estimation differentiating our results by sector according to the Industry Classification Benchmark. We employ data from the NYSE and we estimate varying lengths of beta employing data from 30 to 250 trading days. The constructed beta series is then examined for the presence of breaks using the endogenous structural break literature. Results show evidence against the use of betas that employ more than 90 trading days of data provisional to the sector under study.

This work addresses the problem of automatic head pose estimation and its application in 3D gaze estimation using low quality RGB--D sensors without any subject cooperation or manual intervention. The previous works on 3D head pose estimation using RGB--D sensors require either an offline step for supervised learning or 3D head model construction which may require manual intervention or subject cooperation for complete head model reconstruction. In this paper, we propose a 3D pose estimator based on low quality depth data, which is not limited by any of the aforementioned steps. Instead, the proposed technique relies on modeling the subject's face in 3--D rather than the complete head, which in turn, relaxes all of the constraints with the previous works. The proposed method is robust, highly accurate and fully automatic. Moreover, it does not need any offline step. Unlike some of the previous works, the method only uses depth data for pose estimation. The experimental results on the Biwi head pose database confirm the efficiency of our algorithm in handling large pose variations and partial occlusion. We also evaluate the performance of our algorithm on IDIAP database for 3D head pose and eye gaze estimation.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

a sensorless control scheme based on novel power converging law sliding mode observer is suggested to realize the sensorless control for the permanent magnet synchronous motor (PMSM). Firstly, by introducing a new power converging law, the problem of slow converging speed/large chattering value dilemma in the conventional converging law is solved; Secondly, in view of the shortcomings of the conventional position and speed estimation algorithm, the high-frequency buffeting in the sliding mode observer will be expanded, a phase-locked loop (PLL) velocity and position estimation strategy is adopted to replace it. Finally, through Matlab/Simulink modeling and motor speed regulation platform experimental results, the sensorless position and speed estimation technology proposed in this paper can respond to the starting speed command of 1000 r/min within 0.05 s, and the starting process has no overshoot. When disturbed by 10Nm loading, the speed fluctuation value can be controlled within 1%.

Based on the satellite attitude control method, this paper proposes an attitude control method based on neural network disturbance compensation. The paper firstly analyzes the neural network algorithm and proposes an orthogonal least squares algorithm to implement network learning. In this paper, a set of high-precision directional neural network compensation controllers is designed for the attitude control of acupuncture small satellites. The feasibility of the improved orthogonal least-squared algorithm combined with the neural network supplementary control method in satellite attitude control is verified by experiments.

This paper is concerned with bump-less transfer of parametrized disturbance observer based controller (DOBC) with Individual Pitch Control (IPC) strategy for full load operation of wind turbine. Aerodynamic cyclic loads are reduced by tuning multivariable DOBC with the objective to reduce output power fluctuation, tower oscillation and drive-train torsion. Furthermore tower shadow and wind shear effect are also mitigated using parametrized controller. A scheduling mechanism between two DOBC is developed and tested on Fatigue, Aerodynamics, Structures, and Turbulence ( FAST) code model of National Renewable Energy Laboratory (NREL)’s 5 MW wind turbine. The closed-loop system performance is assessed by comparing the simulation results of proposed controller with a fixed gain and Linear Parameter Varying (LPV) DOBC with Collective Pitch Control (CPC) for full load operation. It is tested with step changing wind to see the behavior of the system under step change with wind shear and tower shadow (cyclic load) effects. Also turbulent wind is applied to see the smooth transition of the controllers. It can be concluded from the results that the proposed parametrized control DOBC with IPC shows smooth transition from one controller to another by interpolation. Moreover fatigue of the gear and tower due to wind shear and tower shadow effects are reduced considerably by the proposed controller as compared to collective pitch control.

Antibiotic prescription is the first line of treating bacterial diseases. But it affects the composition and function of non-targeted intestinal microbiota. Antimicrobial resistance will be the cause for the death of millions of people worldwide. By considering collateral damage of antibiotics, searching an alternative antimicrobial agent will be a solution to minimize the problems. Probiotics, prebiotics and synbiotics are an alternative to antibiotics. Thanks to GIT microbes as they are responsible for metabolism, energy production, protection from pathogens and immunomodulation. So, it is appreciable if the gut microbiota modulated through consumption of probiotics, prebiotics and synbiotics. Probiotic effects are genus and species specific. To get good health benefit of probiotics, safety of probiotics should be assessed before using them. This is mandatory for prebiotics and synbiotic selection. So this review paper gives information about side effects of antibiotics on gut microbiota, description of probiotics, prebiotics and synbiotics as alternative to antibiotics in modulating GIT microbiota, techniques of assessing safety of probiotics and health benefits of probiotics, prebiotics and synbiotics with scientific evidence in clinical trial and some disagreement and challenges of using probiotics, prebiotics and synbiotics.

This study presents an effective control algorithm to improve the robustness of fast steering mirror (FSM)-based laser beam steering systems against dynamic disturbances such as repetitive disturbances resulting from operating conditions. A stable control system must be able to maintain the required high-precision control even when dynamic disturbances affect the FSM system. In this study, an improved control method is proposed using an internal model principle (IMP)-based nonlinear controller with a disturbance observer (DOB) for the FSM system. This IMP-based controller with DOB can attenuate the residual control error signal under dynamic disturbance conditions.

Human disturbance, such as trampling, is an integral component of global change, yet we lack a comprehensive understanding of its effects on alpine ecosystems. Many alpine systems are seeing a rapid increase in recreation, and in understudied regions, such as the Coast Mountains of British Columbia, disturbance impacts on alpine plants remain unclear. We surveyed disturbed (trail-side) and undisturbed (off-trail) transects along elevational gradients of popular hiking trails in the T’aḵ’t’aḵ’múy̓in tl’a In̓inyáx̱a7n region (Garibaldi Provincial Park), Canada, focusing on dominant shrubs (Phyllodoce empetriformis, Cassiope mertensiana, Vaccinium ovalifolium) and graminoids (Carex spp). We used a hierarchical Bayesian framework to test for disturbance by elevation effects on total plant percent cover, maximum plant height and diameter (growth proxies), and buds, flowers, and fruits (reproduction proxies). We found that trampling reduces plant cover and impacts all species, but that effects vary by species and trait, and disturbance effects only vary with elevation for one species’ trait. Growth traits are more sensitive to trampling than reproductive traits, which may lead to differential impacts on population persistence and species level fitness outcomes. Our study highlights that disturbance responses are species-specific, and this knowledge can help land managers minimize disturbance impacts on sensitive vegetation types.

The novel Ionized Gas Thermoelectric Generator (IG-TEG) system that has been studied theoretically showing capabilities to continually extracting energy from the thermal energy of the ambient air, at low temperatures within the standard room temperature and below. This system does not need a temperature gradient in order to work, unlike the other TEGs that use Seebeck effect, and therefore this new system can be utilized for cooling purposes, by extracting energy instead of wasting energy in compressing the gas for cooling. This novel system was designed based on Static Ratchet Potential (SRP), which is known as a spatially asymmetric electric potential produced by an array of positive and negative electrodes. The ratchet potential produces electrical current from random Brownian Motion of charged particles that are driven by thermal energy. Ratchet potential was studied and investigated by several researches in the fields of sensing and energy harvesting. The main ratchet potential system parameter is the particles transportation, this parameter was studied under the condition of flashing ratchet potentials, and was analyzed based on several methods. In this study, a different approach is pursued to estimate particles transportation, by evaluating the charged particles distribution, and applying the other conditions of the SRP.

A class of models for non-Gaussian spatial random fields is explored for spatial field reconstruction in environmental and sensor network monitoring. The family of models explored utilises a class of transformation functions known as the Tukey g-and-h transformations to create a family of warped spatial Gaussian process models which can support various desirable features such as flexible marginal distributions, which can be skewed, leptokurtic and/or heavy-tailed. The resulting model is widely applicable in a range of spatial field reconstruction applications. To utilise the model in applications in practice, it is important to carefully characterise the statistical properties of the Tukey g-and-h random fields. In this work, we both study the properties of the resulting warped Gaussian processes as well as using the characterising statistical properties of the warped processes to obtain flexible spatial field reconstructions. In this regard, we derive five different estimators for various important quantities often considered in spatial field reconstruction problems. These include the multi-point Minimum Mean Squared Error (MMSE) estimators; the multiple point Maximum A-Posteriori (MAP) estimators; an efficient class of multiple-point linear estimators based on the Spatial-Best Linear Unbiased (S-BLUE) estimators; and two multi-point threshold exceedance based estimators, namely the Spatial Regional and Level Exceedance estimators. Simulation results and real data examples show the benefits of using the Tukey g-and-h transformation as opposed to standard Gaussian spatial random fields in a real data application for environmental monitoring.

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.

Estimation and planning play a vital role in the construction of an autonomous navigation framework. However, these problems are often considered separately, while planning gives robot a free-collision path towards the desired goal, estimation algorithm presents the executed trajectory in the sense that it has to be closed to the ground truth path as much as possible. Recently, a unified probabilistic framework, which supports solving these problems simultaneously, dubbed STEAP has been proposed. Nevertheless, its current version is only designated for an omni wheels robot, which allows robot to move and turn in vertical direction. Differential drive robot, on the other hand, though limited to move along only one direction, has been used in various situations due to its flexibility and lower cost in hardware designing. Thus, in this extension, our aim is to control a differential drive robot via STEAP. Moreover, in a more complicated environment such as labyrinth or maze, the original STEAP sometimes fails to find a path. Indeed, this problem is mainly caused by the poor initialization and the non-linearity in optimizer constraints. In our implementation, instead of dealing with these constraints, we employ a global planner algorithm such as Dijkstra or RRT to treat STEAP as an effective local planner module that focus on following the global path. Consequently, the experimental results show that the extended STEAP not only able to navigate a differential drive robot but also in a more complicated and unstructured environment.

This study presents an innovative approach named Optimal Adaptive Continuous Barrier Function Terminal Sliding Mode Control (OACBF-TSMC) approach with a novel switching manifold, to control mathematical model of nonlinear systems under model uncertainties and external disturbances. The proposed OACBF-TSMC approach combines the advantages of adaptive control, continuous barrier functions, and terminal sliding mode control to achieve robust stability of the mathematical model of nonlinear systems, and by using a genetic algorithm that tries to optimize the controller parameters as much as possible so that the proposed controller is the most to have efficiency and performance. The proposed method is designed to address the challenges of systems and provide superior performance in terms of stabilization accuracy, disturbance rejection, and robustness against uncertainties. However, the critical challenge facing the proposed controller is the complete elimination of the chattering phenomenon, which is the most important problem of ordinary sliding mode controllers. The simulation results show that the system trajectories in the proposed approach have converged to the origin with minimal overshoot and under-shoot in a finite time; In addition, the chattering problem in the control inputs has been well eliminated, which makes the proposed method suitable for various systems, including chaotic systems, energy sources, and distributed production systems. Furthermore, the OACBF-TSMC approach has the potential to enhance the stability and reliability of control systems, contributing to the integration of the system states.

Modelling diameter distribution is an integral part of forest management. It requires the use of a suitable probability density function or cumulative distribution function with the appropriate fitting method. In this study, we compared the suitability of eight probability density functions fitted by derivative and optimization methods used for diameter distribution estimation of forest stands. The derivation and optimization were used on A Charlier, beta, generalized beta, gamma, Gumbel, Johnson’s SB, and Weibull (2 and 3-parameter). We used data from 167 permanent sample plots from Atlantic forest (Quercus robur) and 59 temporary sample plots from tropical forests (Tectona grandis). The quality of the fits was evaluated with different indices such as Kolmogorov–Smirnov, Cramer-von Mises, mean absolute error, bias and mean squared error. The results showed Johnson’s SB function was more suitable for describing the diameter distribution of the stands. Johnson’s SB, 3-parameter Weibull and generalized beta had consistent performance regardless of the fitting methods. The quality of fits produced by gamma, Gumbel and 2-parameter Weibull was poor.

This interdisciplinary investigation of the human remains of Balduin Helm, one of the most important abbots of Fürstenfeld monastery, provides novel information on that historic individual. This is particularly interesting since Balduin, during early 18th century, was involved in the renovation of this large Bavarian monastery. Metastatic prostate cancer was found as evidenced by multiple mixed osteolytic-osteoblastic bone lesions in all available vertebral bodies, fragments of both hemipelvises and isolated metastases in skull bones. Distribution, radio- and histomorphology, and especially the immunohistochemical detection of prostate-specific antigen in those metastases, definitively confirm this diagnosis. Further investigation, especially by stable isotope analysis, showed a balanced high-level diet with considerable contribution from animal protein and significant freshwater fish. These additional findings suggest a significant radiocarbon reservoir effect as an explanation for a “too old” radiocarbon dating. Finally, the obviously high-level protein diet may have contributed to the tumorigenesis which caused the death of the abbot at an advanced age.

The development of hybrid unmanned aerial underwater vehicles (HAUVs) compatible with the advantages of the aerial vehicles and the underwater vehicles is of great significance. This paper presents the first study on a new HAUV layout using four rotors to realize the medium crossing motion of a transverse slender body similar to the fuselage of a missile or a submarine, that is the hybrid aerial underwater quadrotor (HAUQ). Then a robust control strategy is proposed for the take-off HAUQ on the water in the presence of unknown disturbances and complex model dynamic uncertainties. As a semi-submersible HAUQ rises straightly from the water, the inside of the slender fuselage placed horizontally is filled with water. The center of the mass, the moment of inertia, and the arm of force of the HAUQ will change rapidly in the takeoff phase from the water since the rapid non-uniform change of mass caused by the passive fast drainage. It is difficult to establish a accurate mathematical model of the complex dynamic changes caused by the multi-media dynamics, the fast changing buoyancy, and the added mass crossing air–water surface. Therefore, an uncertain kinematic and dynamic model is established through the passive fast nonuniform change and the complex dynamics are considered as the unknown terms, and the external disturbances of gust and other factors are assumed as the bounded disturbance input. A robust design approach is introduced to deal with the fast time-varying mass disturbance based on the input-to-state stability (ISS) theorem. The complex dynamics are estimated using the basis function and the unknown weight parameters, and the adaptive laws are adopted for the on-line estimation of the unknown weight parameters. Consider the residual disturbance of the uncertain nonlinear system as a total disturbance term, a disturbance observer is introduced for disturbance observation. The numerical simulation shows the feasibility and robustness of the proposed algorithm.

Seagrass ecosystems are lost due to habitat disturbance, coastal development and human pressure. We assessed the impact of boat anchors from traditional fishing and recreational activities on the seagrass Halophila ovalis from the Andaman and Nicobar Isalnds of India. The plant density, biomass, morphometrics, canopy height and percentage cover were estimated from two sites of Govind Nagar beach of Andaman and Nicobar Islands. The shoot density of H. ovalis was reduced by physical damage caused by boat anchors. The morphometrics of H. ovalis, such as number of leaves per ramet, leaf length, width and horizontal rhizome length were significantly reduced when impacted by boat anchors. Seagrass canopy height and percentage cover were reduced by 41% and 47% respectively. Though the impact of boat anchors reported here is on small-scale, it may impact feeding grounds of locally endangered dugongs. Therefore, proper management and preventive measures should be implemented to prevent the loss of dugong grass habitats from tourism, recreational and fishing activities.

Alpine forest gaps can distribute snowfall, solar radiation and rainfall, thus inducing a heterogeneous hydrothermal microenvironment between the inside and outside areas of forest gaps. Additionally, the characteristics of the heterogeneous microenvironment could vary greatly across the gap location properties during winter and the growing season. To determine the response of total phenol loss (TPL) from the litter to alpine forest gap disturbance during decomposition, we conducted a field litterbag experiment within a representative fir (Abies faxoniana Rehd.) forest based on the gap location properties. The TPL and abundances of fungi and bacteria from two typical shrub species (willow, Salix paraplesia Schneid., and bamboo, Fargesia nitida (Mitford) Keng f.) were measured during the following periods over two years: snow formation (SF), snow cover (SC) snow melting (ST), the early growing season (EG) and the later growing season (LG). At the end of the study, we found that the snow cover depth, frequencies of the freeze-thaw cycle and the fungal copy g-1 to bacterial copy g-1 ratio had significant effects on the litter TPL. The abundances of fungi and bacteria decreased from the gap center to the closed canopy during the two SF, SC, ST and LG periods and reversed during the two EG periods. The TPL closely followed the same trend as the microbial abundance during the first year of incubation. In addition, both species had larger TPLs in the gap center during the first winter, first year and entire two years. These findings suggest that alpine forest gap formation accelerates litter TPL and plays a dual role during specific critical periods by distributing abiotic and biotic factors directly and indirectly. In conclusion, reduced snow cover depth and duration during winter warming under current climate change scenarios or as gaps vanish may slow litter TPL in alpine biomes.

The population’s mobility in urban areas is a necessary variable in the modeling of risk scenarios caused by atmospheric contamination. The inclusion of this concept makes static models more dynamic while considering people within a city to be an entity with complex mobility processes. We propose a conceptual and methodological tool to make the representation of the social, economic and territorial components, as well as the patterns in the population´s mobility to delimitate risk areas for human health by exposure of contaminants. In the volatile organic compounds (VOC), benzene, ethylbenzene, toluene and xylene (BTEX) are amongst the most dominant substances in fugitive vapor emissions in gas stations (GS). In urban areas, the exposure to BTEX by residential proximity and proximity to other facilities, which cause intra-urban agglomeration, can impact and affect human health. This model seeks to facilitate the focalization, identification and prioritization of risk areas by BTEX environmental contamination. This article goes beyond de conceptual framework. It suggests methodological and instrumental aspects to be applied in other cities. The government agencies must consider these results when establishing rules, permissions and procedures to reduce environmental pollution for managing the risk in a complex urban environment.

Software project estimating (SPE) is a powerful but necessary step in the production of projects for software. Software project estimating includes several components, estimating software time, software resources, software costs, and software effort estimation (SEE). SEE seeks to estimate the number of "hours-person" and "months-person" of work required for developing or managing a software program. During the initial phase of the development of software, future efforts are impossible to predict. To estimate effort, many deep learning (DL) and machine learning (ML) models were previously created. For estimate, single-model techniques and ensemble methods were investigated in this research. Ensemble methods involve a combination of multiple separate models. Bagging, boosting, and voting were the ensemble methods looked into for estimation. Datasets considered for estimation were COCOMO81, COCOMONasa I, COCOMONasa II, Albrecht, Maxwell, China, Desharnais, Desharnais_1_1, Kitchenham, Boehm, and Belady. The evaluation criteria used MAE, RAE, RMSE, RRSE, and CC. The result from previous studies is that the total size of the set of data utilized is small in predicting the effort, as the largest size of the set of data used is the China dataset containing only 499 projects. So, in this study, the dataset has been merged to increase the total size of the set of data and increase the accuracy of prediction. The results indicated that the suggested merged dataset increased effort estimation accuracy.

Crowd density estimation is an important task for crowd monitoring. Many efforts have been done to automate the process of estimating crowd density from images and videos. Despite series of efforts, it remains a challenging task. In this paper, we proposes a new texture feature-based approach for the estimation of crowd density based on Completed Local Binary Pattern (CLBP). We first divide the image into blocks and then re-divide the blocks into cells. For each cell, we compute CLBP and then concatenate them to describe the texture of the corresponding block. We then train a multi-class Support Vector Machine (SVM) classifier, which classifies each block of image into one of four categories, i.e. Very Low, Low, Medium, and High. We evaluate our technique on the PETS 2009 dataset, and from the experiments, we show to achieve 95% accuracy for the proposed descriptor. We also compare other state-of-the-art texture descriptors and from the experimental results, we show that our proposed method outperforms other state-of-the-art methods.

Cycle times at workstations in offsite construction factories fluctuate widely due to various influencing factors. Consequently, relying on average rates, such as length per unit of time, for estimating cycle times proves to be inaccurate, often leading to significant deviations between production schedules and actual operations. To address this issue, this study proposes an estimation system that leverages machine-learning-based prediction, statistical methods, 3D simulation, and computer vision to predict cycle times at the workstation level. Testing of the system on a semi-automated wood-wall framing workstation in a panelized construction factory shows that it reduces the mean absolute error and sum of errors by approximately 36% and 68%, respectively, compared to the fixed rate method. The results also highlight the efficacy of using computer vision data for training machine-learning models for cycle time estimation, the importance of identifying and understanding the factors influencing cycle times, and the impact of random delays on the accuracy of cycle time estimation systems.

In many research fields, statistical probability models are often used to analyze real-world data. However, data from many fields, such as the environment, economics, and health care, do not necessarily fit traditional models. New empirical models need to be developed to improve their fit. In this paper, we explore a further extension of the quasi-Lindley model. Maximum likelihood, least square error, Anderson-Darling algorithm, and expectation-maximization algorithm are four techniques for estimating the parameters under study. All techniques provide accurate and reliable estimates of the parameters. However, the mean square error of the expectation maximization approach was lower. The usefulness of the proposed model was demonstrated by analyzing a dynamical systems data set, and the analysis shows that it outperforms the other models in all statistical models considered.

The power function distribution is a flexible waiting time model that may provide better fit for some failure data. This paper presents the comparison of the maximum likelihood estimates and the Bayes estimates of two-parameter power function distribution. The Bayes estimates are obtained, using conjugate priors, under five loss functions consist of square error, precautionary, weighted, LINEX and DeGroot loss function. The Gibbs sampling algorithm is proposed to generate samples from posterior distributions and in result the Bayes estimates are computed. The comparison of the maximum likelihood estimates and the Bayes estimates are done through the root mean squared errors. One real-life data set is analyzed to illustrate the evaluation of proposed methods of estimation. Finally, results from the simulation are discussed to assess the performance behavior of the maximum likelihood estimates and the Bayes estimates.

Structural displacement is an important metric for assessing structural conditions because it has a direct relationship with the structural stiffness. Many bridge displacement measurement techniques have been developed, but most methods require fixed reference points in the vicinity of the target structure which limits field implementations. A promising alternative is to use reference-free measurement techniques that indirectly estimate the displacement by using measurements such as acceleration, and strain. This paper proposes novel reference-free bridge displacement estimation by the fusion of single acceleration with pseudo-static displacement derived from co-located strain measurements. First, we propose a conversion of the strain at the center of a beam into displacement based on the geometric relationship between strain and deflection curves with reference-free calibration. Second, an adaptive Kalman filter is proposed to fuse the displacement generated by strain with acceleration by recursively estimate the noise covariance of displacement from strain measurements which is vulnerable to measurement condition. Both numerical and experimental validations are presented to demonstrate the efficiency and robustness of the proposed approach.

Visual inertial odometry (VIO) has recently received much attention for efficient and accurate ego-motion estimation of unmanned aerial vehicle systems (UAVs). Recent studies have shown that optimization-based algorithms achieve typically high accuracy when given enough amount of information, but occasionally suffer from divergence when solving highly non-linear problems. Further, their performance significantly depends on the accuracy of the initialization of inertial measurement unit (IMU) parameters. In this paper, we propose a novel VIO algorithm of estimating the motional state of UAVs with high accuracy. The main technical contributions are the fusion of visual information and pre-integrated inertial measurements in a joint optimization framework, and the stable initialization of scale and gravity using relative pose constraints. To count for ambiguity and uncertainty of VIO initialization, a local scale parameter is adopted in the online optimization. Quantitative comparisons with the state-of-the-art algorithms on the EuRoC dataset verify the efficacy and accuracy of the proposed method.

Inflammation is a cause of number of disorders. Many anti-inflammatory drugs are available to cure and prevent inflammation and its related disorders. Some of the drugs are from plant and animal origin. Among animals snake venom is also utilized as treatment option of certain disorders. In the current study the venom of N. oxiana from Northern areas of Pakistan is assayed to determine its anti-inflammatory activity. The Naja oxiana is also called central Asian cobra is endemic to Central Asia. Naja oxiana belong to family Elapidae and it is highly venomous snake. The venom has many enzymatic proteins as well as nonenzymatic proteins that is neurotoxins. The venom is lethal having very high mortality rate and the death may occur due to respiratory failure in 45 minutes to 24 hrs depending upon the nature and amount of venom. As the venom is highly toxic so initially after venom milking its protein estimation was done and toxicity profile and LD50 was determined to find out its therapeutic dose at which anti-inflammatory activity was observed. The toxicity and anti-inflammatory activity was determined on mice model. Inflammation was induced by carrageenan induced peritonitis method. The inflammatory markers ROS, TNF-α and IL-β were determined by ELIZA in peritoneal fluid. The LD50 of crude venom, fraction 1 and fraction 2 was found as 34 µg/kg, 7.4 µg/kg and 416 µg/kg respectively. Anti-inflammatory activity crude venom, fraction 1 and fraction 2 was found at dose 19 µg/kg, 1.8 µg/kg and 267 µg/kg respectively. The levels of inflammatory markers reduced after therapeutic dose administration of venom and its fractions that indicates that it can be utilized as anti-inflammatory agent and so can be effective in various disorders.

Introduction: The transcranial direct current stimulation (tDCS) is a promising technique for brain modulation after cerebrovascular accident (CVA). This treatment modality has been previously studied in the recovery of patients. The aim of this review is to analyze the evidence in the ap-plication of tDCS in the recovery of gait disturbance in stroke patients. Methods: This review was conducted according to the recommendations of the PRISMA statement. Three different elec-tronic databases were searched for relevant results: PubMed, Scopus, and Cochrane. We included reviews and meta-analyses that only considered randomized controlled trials (RCTs) that inves-tigated the effects of transcranial direct electrical stimulation, in combination or not with other physiotherapy treatment, on gait recovery. Results: Thirteen studies with a total of 195 RCTs were included. Data on population, outcome measures, protocols and outcomes were extracted. The Amstar-2 scale and the GRADE system of certainty of evidence were used. Only one study re-ceived high certainty of evidence, 5 received low certainty of evidence and 7 received critically low certainty of evidence. Conclusions: Although the tDCS produces positive changes in gait recovery in spatio-temporal parameters, mobility, endurance, strength and motor function, there is insuf-ficient evidence to recommend this treatment.

In this paper, a two-link manipulator system stability performance is designed and analyzed using Optimal control technique. The manipulator system is highly nonlinear and unstable. The system is modelled using Lagrangian equation and linearized in upward unstable position. The closed loop system is designed using optimal sliding mode controller. The system is compared with a known PID controller with an impulse applied and disturbance torques and a promising results has been obtained.

The main result of this work is the estimation of the entropy mode accompanying a wave disturbance, observed at the atmosphere heights range of 90-120km. The study is the direct continuation and development of recent results on diagnosis of the acoustic wave with the separation on direction of propagation. The estimation of the entropy mode contribution relies upon the measurements of the three dynamic variables (the temperature, density and vertical velocity perturbations) of the neutral atmosphere measured by the method of the resonant scattering of radio waves on the artificial periodic irregularities of the ionospheric plasma. The measurement of the atmosphere dynamic parameters has been carried out on the SURA heating facility. The mathematical foundation of the mode separation algorithm is based on the dynamic projecting operator technique. The operators are constructed via the eigenvectors of the coordinate evolution operator of the transformed system of balance equations of the hydro-thermodynamics.

Nitrogen is one of the most important macronutrients for crops, and in conjunction with artificial intelligence algorithms, it is possible to estimate it with the aid of vegetation indices through remote sensing. Various indices were calculated and those with a correlation ≥ 0.7 were selected for subsequent use in Random Forest, Gradient Boosting, and Artificial Neural Networks to determine their relationship with nitrogen levels measured in the laboratory. Random Forest showed no relationship, yielding an R2 of zero, whereas Artificial Neural Networks yielded the best results with an R2 of 0.93. Thus, it is reliable to estimate nitrogen levels using this algorithm by feeding it with data from TCARI, MCARI, TCARI/OSAVI, and MCARI/OSAVI, assisted by technological tools.

A number of accidents at sea are primarily caused by low visibility due to sea fog therefore, it is important to estimate sea fog intensity and visibility in real-time in the ocean environment. However, the existing estimation systems have significant costs so that it is not viable to install them at various locations, such as small vessels, minor ports, and a number of buoys. Therefore, this paper proposes an algorithm called RDCP (Reduced Dark Channel Prior) which provides the estimation at a low complexity and a low cost. For the estimation, the RDCP algorithm firstly acquires dark channels from an ocean image, then applies an optimized threshold value to the dark channels, and crops out the sky region in the ocean image. For the estimation performance evaluation, 320 raw images captured from cameras at four different ports in South Korea are used rather than artificially composed images. Considering facilities in oceans which are usually operated in the power limited environment, the processing time performance of PDCP are also examined. The experiments demonstrate that the RDCP algorithm provides reliable estimation performance in real-time.

Rice canopy height and density are directly usable crop phenotypic traits for the direct estimation of crop biomass. Therefore, it is crucial to rapidly and accurately estimate rice canopy phenotypic parameters. To achieve non-destructive detection and estimation of essential phenotypic parameters in rice, a platform based on LiDAR point cloud data for rice phenotypic parameter detection was established. Data collection of rice canopy layers was performed across multiple plots. The LiDAR-detected canopy top point clouds were selected using a method based on the highest percentile, and the rice canopy surface model was calculated. Canopy height estimation was the difference between ground elevation and percentile value. To determine the optimal percentile defining the rice canopy top, testing was conducted incrementally from 0.8 to 1 with an increment of 0.005. The optimal percentile value was found to be 0.975. The root mean square error (RMSE) between LiDAR-detected canopy height and manually measured canopy height was calculated. The prediction model based on canopy height (R2=0.941, RMSE=0.019) exhibited a strong correlation with actual canopy height. Linear regression analysis was conducted between gap fraction of different plots and manually detected average Leaf Area Index (LAI) of rice canopy. Prediction models for canopy LAI based on ground return counts (R2=0.24, RMSE=0.1) and ground return intensity (R2=0.28, RMSE=0.09) showed strong correlations but had lower correlation with rice canopy LAI. Regression analysis was performed between LiDAR-detected canopy height and manually measured rice canopy LAI. The results indicated that the prediction model based on canopy height (R2=0.77, RMSE=0.03) was more accurate.

Foundational and state-of-the-art anomaly detection methods through power system state estimation are reviewed. The traditional components for bad data detection such as chi-square testing, residual-based methods, and hypothesis testing are discussed to explain the motivations for recent anomaly detection methods given the increasing complexity of power grids, energy management systems, and cyber-threats. In particular, state estimation anomaly detection based on data-driven quickest change detection and artificial intelligence are discussed and directions for research are suggested with particular emphasis on considerations of the future smart grid.

United Nations Framework Convention on Climate Change (UNFCCC) has recently established the Reducing Emissions from Deforestation and forest Degradation (REDD+) program that requires countries to report their carbon emissions and sink estimates through national greenhouse gas inventories (NGHGI). Thus, developing automatic systems capable of estimating the carbon absorbed by forests without in-situ observation becomes essential. To support this important need, in this work we introduce ReUse, a simple but effective deep-learning approach to estimate the carbon absorbed by forest areas based on remote sensing. The novelty of the proposed method is in the use of the public above-ground biomass (AGB) data from the European Space Agency's Climate Change Initiative Biomass project as ground truth to estimate the carbon sequestration capacity of any portion of land on Earth using Sentinel-2 images and a pixel-wise Regressive UNet. The approach has been compared to two literature proposals, using a private dataset and human-engineered features. The results show a greater generalization ability of the proposed approach, with a decrease in Mean Absolute Error and Root Mean Squared Error, respectively, of 16.9 and 14.3 in the area of Vietnam and 4.7 and 5.1 in the area of Myanmar over the runner-up. Finally, as a case study, we reported an analysis made for the Astroni area, a nature reserve located near the metropolitan area of Naples in southern Italy, struck by a large fire, producing predictions consistent with values found by experts in the field. These results further support the use of such an approach for the early detection of AGB variations, both in urban and rural areas.

Background & Motivation: Stroke outcomes following revascularization therapy (intravenous thrombolysis, IVT, and/or mechanical thrombectomy, MT) depend critically on time from stroke onset to treatment. Different service configurations may prioritise time to IVT or time to MT. In order to evaluate alternative acute stroke care configurations, it is necessary to estimate clinical outcomes given differing times to IVT and MT. Method: Model using an algorithm coded in Python. This is available at https://github.com/MichaelAllen1966/stroke_outcome_algorithm. Results: We demonstrate how the code may be used to estimate clinical outcomes given varying times to IVT and MT. Conclusion: Python code has been developed and shared to enable estimation of clinical outcome given times to IVT and MT. Here we share pseudocode and links to full Python code.

In the context of precision agriculture (PA), geomatic surveys exploiting UAV platforms allow the trees’ dimensional characterization and crown identification. This paper focuses on the use of low-cost UAV photogrammetry to estimate the trees’ height, as part of a project for the phytoremediation of contaminated soils. Two study areas (Area 1; Area 2) have been chosen, having different characteristics in terms of mean trees’ height (5 m; 0.7 m), to test the procedure even in a challenging context. Three campaigns have been performed in Area 1 at different altitudes (30 m, 40 m, 50 m), and one UAV flight is available in Area 2 (42 m of altitude). The implemented workflow involves the elaboration of the UAV point clouds and DSMs using the standard SfM approach, the vegetation filtering, the generation of the DTM and a GIS-based analysis to obtain the CHMs for the extraction of the trees’ heights based on a local maxima approach. UAV-derived heights have been compared with in-field measurements obtaining promising results in Area 1, confirming the applicability of the procedure for trees’ height extraction, while the application in the context of low trees was more problematic.

Nonparametric density estimation for nonnegative data is considered in a situation where a random sample is not directly available but the data are instead observed from the length-biased sampling. Due to the boundary bias problem of the location-scale kernel, the approach in this paper is an application of asymmetric kernel. Two nonparametric density estimators are proposed. The mean integrated squared error, strong consistency, and asymptotic normality of the estimators are investigated. Some simulations illustrate the finite sample performance of the estimators.

Layout estimation is a challenge of segmenting a cluttered room image into floor, walls and ceiling. We applied Double refinement network proved to be efficient in the depth estimation to generate heat maps for room key points and edges. Our method is the first not using encoder-decoder architecture for the room layout estimation. ResNet50 was utilized as a backbone for the network instead of VGG16 commonly used for the task, allowing the network to be more compact and faster. We designed a special layout score function and layout ranking algorithm for key points and edges output. Our method achieved the lowest pixel and corner errors on the LSUN data set. The input image resolution is 224*224.

We propose an electrocardiogram (ECG) signal-based algorithm to estimate the respiratory rate is a significant informative indicator of physiological state of a patient. The consecutive ECG signals reflect the information about the respiration because inhalation and exhalation make transthoracic impedance vary. The proposed algorithm extracts the respiration-related signal by finding out the commonality between the frequency and amplitude features in the ECG pulse train. The respiration rate can be calculated from the principle components after the procedure of the singular spectrum analysis. We achieved 1.7569 breaths per min of root-mean-squared error and 1.7517 of standard deviation with a 32-seconds signal window of the Capnobase dataset, which gives notable improvement compared with the conventional Autoregressive model based estimation methods.

We present a new method of estimating fitness of countries and complexity of products by exploiting a non-linear non-homogeneous map applied to the publicly available information on the goods exported by a country. The non homogeneous terms guarantee both convergence and stability. After a suitable rescaling of the relevant quantities, the non homogeneous terms are eventually set to zero so that this new method is parameter free. This new map reproduces the findings of the method proposed by Tacchella et al. [1], and allows for an approximate analytic solution in case of actual binarized matrices based on the Revealed Comparative Advantage (RCA) indicator. This solution is connected with a new quantity describing the neighborhood of nodes in bipartite graphs, representing in this work the relations between countries and exported products. Moreover, we define the new indicator of country net-efficiency quantifying how a country efficiently invests in capabilities able to generate innovative complex high quality products. Eventually, we demonstrate analytically the local convergence of the algorithm.

According to the IPCC guidelines, CO₂ emissions from biomass should be excluded from the entire amount of CO₂ emissions when calculating CO₂ emissions and should be separately reported due to the “carbon neutrality.” Sewage sludge is one of the representative biomass fuels. And it is mixed with fossil fuels in terms of greenhouse gas reduction or is used as fuel to replace fossil fuels by itself. According to the results of this study, biomass contents of both the sewage sludge and the sewage sludge incineration exhaust gases did not amount to 100%. At present, in many countries(South Korea, Japan, and Germany), when calculating greenhouse gas emissions from sewage sludge incinerator, all CO₂ emissions from sewage sludge are judged to be biomass and only those greenhouse gas emissions that correspond to Non-CO₂ gases are calculated as greenhouse gas emissions. However, since, according our results, the content of sewage sludge is not 100% biomass, if CO₂ emissions are excluded according to the existing greenhouse gas emission calculation method, the amount of emissions may be underestimated. Therefore, to accurately calculate greenhouse gas emissions from sewage sludge incinerator, CO₂ emissions should be calculated in consideration of the fossil carbon contents of sewage sludge.

In this paper, the stability control of the inverted pendulum on a cart with a disturbance forces has been done using observer based and full state feedback H2 controllers. The Lagrangian equation has been used to model the system equation of motions and linearized the system to the unstable upward position. Comparison of the system stability has been simulated by comparing the proposed controllers using Matlab/Scripts and a promising results has been analyzed successfully.

VE is a powerful technique for analyzing a design with a focus on functionality, reducing costs, and increasing value. However, in order to proceed with the design of VE, the theoretical basis for the VE target selection process, which must be preceded in the preparation stage, is lacking, and as a result, it is difficult to verify the most effective target selection. Thus, a theoretical basis is needed. In this study, we intend to quantify the WORTH value of the COST TO WORTH technique and present an objective model of the target selection method using the derived Value Index (VI). For this purpose, cost worth (WORTHC) was calculated based on the performance data of 1,008 cases of 15 building types provided by the Domestic Public Procurement Service and the share of 83 detailed processes in 7 fields. Then, a survey was conducted targeting the ordering companies, and the final worth (WORTHF) was calculated by multiplying the derived customer value (WORTHV ) weight for each detailed work type. We calculated the Value Index (VI) by comparing COST and WORTHF for each detailed construction type of the VE project and developed a model to select construction types that exceed the VI standard value derived using the standard error of the population. Both cost experts and non-cost experts can use the developed model to specify the VE target selection criteria in order to easily select the key target, objectively sort the values that serve as the basis for calculating the value index and make it possible to more easily select the VE target selection criteria based on theoretical evidence. Also, the model can be used to obtain effective detailed design VE results.

Cadmium (Cd) is a pervasive, toxic environmental pollutant that preferentially accumulates in tubular epithelium of the kidney. Current evidence suggests that the cumulative burden of Cd here leads to progress loss of the glomerular filtration rate (GFR). In this study, we have quantified changes in estimated GFR (eGFR) and albumin excretion (Ealb) in according to levels of blood Cd ([Cd]b) and excretion of Cd (ECd) after adjustment for confounders. ECd and Ealb were normalized to creatinine clearance (Ccr) as ECd/Ccr and Ealb/Ccr. Among 482 residents of Cd-polluted and non-polluted regions of Thailand, 8.1% had low eGFR and 16.9% had albuminuria, (Ealb/Ccr)×100 ≥ 20 mg/L filtrate. In the low Cd burden group, (ECd/Ccr) ×100 < 1.44 µg/L filtrate, eGFR did not correlate with ECd/Ccr (β = 0.007), while an inverse association with ECd/Ccr was found in the medium (β =−0.230) and high-burden groups (β =−0.349). Prevalence odds ratios (POR) for low eGFR were increased in the medium (POR 8.26) and high Cd burden groups (POR 3.64). Also, eGFR explained a significant proportion of Ealb/Ccr variation among those with middle (η2 0.093) and high [Cd]b tertiles (η2 0.132), but did not with low tertile (η2 0.001). With adjustment of eGFR, age and BMI, POR values for albuminuria were increased in the middle (POR 2.36) and high [Cd]b tertiles (POR 2.74) and those with diabetes (POR 6.02) and hypertension (2.05). These data argue that ECd/Ccr of 1.44 µg/L filtrate (0.01−0.02 µg/g creatinine) could determine a Cd threshold level from which protective exposure guidelines should be formulated.

This paper addresses the problem of low accuracy of conventional channel estimation and signal detection in complex fields like mines; and the problem of replacing the deep receiver at the receiver side with a deep neural network requires a large amount of data for training and slow training time. Combining the receiver side with traditional communication knowledge, a channel estimation and signal detection method based on the joint ReEsNet and SDRNet under the mine is proposed. The detailed step is to use ReEsNet network for interpolation of conventional channel estimation. Then, on the basis of ReEsNet, the output data is channel equalized and pilots removed, and the previously processed data is input to SDRNet to perform signal recovery. In the complex mine environment, the MSE values are 2e-2 for LS, 6e-3 for MMSE, and 8.44e-5 for ReEsNet at the 1500th sample data for interpolation compared to the conventional channel estimation. the MSE of ReEsNet is the smallest and is closer to the real channel estimation. Compared with the proposed joint channel estimation and signal detection methods, fewer trainable parameters reduce 97% of the parameters compared to CCRNet and 84% of the parameters compared to CNNNet; their detection results, however, are not very different.

In recent decades, there have been numerous endeavors to develop a novel category of survival distributions possessing enhanced flexibility through the extension of existing distributions. This article constructs and validates the statistical properties of a novel survival distribution in order to obtain an alternative distribution that is suitable for analyzing survival data by presenting the novel mixture of the Fréchet distribution along with statistical properties such as the probability density function (PDF), cumulative distribution function (CDF), rth ordinary moment, skewness, kurtosis, moment-generating function, mean, variance, mode, survival function, hazard function, and asymptotic behavior, as well as constructing the estimators of the unknown parameter by employing the expectation-maximization (EM) algorithm, and simulated annealing. Additionally, the performance of the proposed estimators was compared with bias, mean squared errors (MSE), and simulated variances, and given an illustrative example of the proposed distribution to the survival data set in order to show that the proposed distribution is appropriate for the right-skewed data. This will be extremely advantageous in survival analysis.

When there is uncertainty in the value of parameters of the input random components of a stochastic simulation model, two-level nested simulation algorithms are used to estimate the expectation of performance variables of interest. In the outer level of the algorithm (n) observations are generated for the parameters, and in the inner level (m) observations of the simulation model are generated with the value of parameters fixed at the value generated in the outer level. In this article, we consider the case in which the observations at both levels of the algorithm are independent, showing how the variance of the observations can be decomposed into the sum of a parametric variance and a stochastic variance. Next, we derive central limit theorems that allow us to compute asymptotic confidence intervals to assess the accuracy of the simulation-based estimators for the point forecast and the variance components. Under this framework, we derive analytical expressions for the point forecast and the variance components of a Bayesian model to forecast sporadic demand; and we use these expressions to illustrate the validity of our theoretical results by performing simulation experiments using this forecast model.

Automatic and real-time pose estimation is important in monitoring animal behavior, health and welfare. In this paper, we utilized pose estimation for monitoring farrowing process to prevent piglet mortality and preserve the health and welfare of sow. State-of-the-art Deep Learning (DL) methods have lately been used for animal pose estimation. The aim of this paper was to probe the generalization ability of five common DL networks (ResNet50, ResNet101, MobileNet, EfficientNet and DLCRNet) for sow and piglet pose estimation. These architectures predict body parts of several piglets and the sow directly from input video sequences. Real farrowing data from a commercial farm was used for training and validation of the proposed networks. The experimental results demonstrated that MobileNet was able to detect seven body parts of the sow with median test error of 0.61 pixels.

Precise binding affinity predictions are essential for structure-based drug discovery (SBDD). Focal adhesion kinase (FAK) is a member of the tyrosine kinase protein family and is overexpressed in a variety of human malignancies. Inhibition of FAK using small molecules is a promising therapeutic option for several types of cancer. Here, we conducted computational modeling of FAK targeting inhibitors using 3-dimensional structure-activity relationship (3D-QSAR), molecular dynamics (MD), and hybrid topology-based free energy perturbation (FEP) methods. The structure-activity relationship (SAR) studies between the physicochemical descriptors and inhibitory activities of the chemical compounds were performed with reasonable statistical accuracy using CoMFA and CoMSIA. These are two well-known 3D-QSAR methods based on the principle of supervised machine learning (ML). Essential information regarding residue-specific binding interactions was determined using the MD and MM-PB/GBSA methods. Finally, physics-based relative binding free energy (〖∆∆G〗_RBFE^(A→B)) values of analogous ligands were estimated using the alchemical FEP simulation. An acceptable agreement was observed between the experimental and computed relative binding free energies. The overall results using ML and physics-based hybrid approaches could be useful for the rational optimization of accessible lead compounds with similar scaffolds targeting the FAK receptor.