The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

We study the electron spin resonance (ESR) line width for localized moments within the framework of the Kondo lattice model. An ESR signal for an impurity can only be observed if the Kondo temperature is sufficiently small. On the other hand, for the Kondo lattice, short-range ferromagnetic correlations (FM) between the localized spins are necessary to obtain an observable signal. The spin relaxation rate (line width) is inversely proportional to the static magnetic susceptibility. The FM enhance the susceptibility and hence reduce the line width. For most of the heavy fermion systems displaying an ESR signal the FM arise in the ab-plane from the strong lattice anisotropy. An ESR signal was observed in the cubic heavy fermion compound CeB₆ which has a Γ₈ ground-quartet. The orbital content of the Γ₈-quartet gives rise to an antiferro-quadrupolar ordered (AFQ) phase below 4 K. Single ions with a Γ₈ ground-multiplet are expected to display four transitions, however, only one has been observed. We address the effects of the interplay of AFQ and FM on the phase diagram and the ESR line width. While for anisotropic Ce and Yb compounds with ESR-signal it is difficult to distinguish if the resonance is due to localized spins or conducting heavy electron spins, an itinerant picture within the AFQ phase is necessary to explain the electron spin resonances for CeB₆. The longitudinal magnetic susceptibility has a quasi-elastic central peak of line width 1/T₁ and inelastic peaks for the absorption/emission of excitation. The latter are measured via inelastic neutron scattering (INS) and provide insights into the magnetic order. We briefly summarize some of the INS results for CeB₆ in the context of the picture that emerged from the ESR experiments.

The rationalization and modeling of an electric discharge in a fluid require the knowledge of electron swarm parameters. In this work, transport coefficients of alcohols, including methanol, ethanol, propanol, and butanol are reported. The electron energy distribution function, mean energy, reduced mobility, and diffusion coefficient, are calculated using the two-term expansion of the electron Boltzmann equation in the frame of BOLSIG+ and the Monte Carlo collision code METHES. For such, experimental and theoretical values of the electron-alcohol collision cross-section, covering a range of electron impact energy from 1 eV to 1000 eV, are employed. A temperature of 300K, reduced fields E/N between $1-10^4$ Td (1Td = $10^{-21}~\rm Vm^2$), and Plasma density of $10^{19}~\rm m^{-3}$ were used in simulations. The calculated coefficients are compared with data available from previous studies.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Biohydrogen is a versatile energy carrier for the generation of electric energy from renewable sources. Hydrogenases can be used in enzymatic fuel cells to oxidize dihydrogen. The rate of electron transfer (ET) at the anodic side between the [NiFe]-hydrogenase enzyme distal iron-sulfur cluster and the electrode surface can be described by the Marcus equation. All parameters for the Marcus equation are accessible from DFT calculations. The distal cubane FeS-cluster has a three cysteine and one histidine coordination [Fe₄S₄](His)(Cys)₃ first ligation sphere. The reorganization energy (inner- and outer-sphere) is almost unchanged upon a histidine-to-cysteine substitution. Differences in rates of electron transfer between the wild-type enzyme and the all-cysteine mutant can be rationalized by a diminished electronic coupling between the donor and acceptor molecules in the [Fe₄S₄](Cys)₄ case. The fast and efficient electron transfer from the distal iron-sulfur cluster is realized by a fine-tuned protein environment which facilitates the flow of electrons. This study enables the design and control of electron transfer rates and pathways by protein engineering.

Motivated by assumptions that Quantum Mechanics (QM) is not the basement of reality and that additional dimensionality (XD) is required to complete and extend the Standard Models (SM) of Particle Physics and Cosmology, experimental protocols utilizing putative properties of Kaluza-Klein-like (KK) cyclicality embedded within Dirac’s electron hypertube model in conjunction with a Dirac covariant polarized vacuum is developed to produce a new type of low-energy tabletop cross section based on topological phase transitions rather than high energy collision sprays as in the LHC. The model is presented in a highly theoretical axiomatic manner utilizing off-the-shelf parameters generally marginalized by the mainstream physics community. When successful the protocol leads to obsolescence of the highly efficacious 100-year supercollider run producing a paradigm shift with an inherent new set of Unified Field (UF) transformations beyond the Galilean Lorentz-Poincaré transformations of the SM to 3rd regime natural science: Classical – Quantum - UF.

For many disciplines of science, all conceivable collisional cross sections and reactions must be precisely known. Although the recent decades were a trial of large-scale research to give these data, many essential atomic and molecular cross section data still missing, and the reliability of the existing cross sections has to be validated. In this paper, we present electron stripping, electron capture, and system breakdown cross sections in carbon (C5+) ions and lithium (Li2+) ions collisions with atomic hydrogen based on the Monte Carlo models of classical and quasi-classical trajectories. According to our expectation, the QCTMC results show higher results in comparison to standard CTMC data, emphasizing the role of Heisenberg correction constraint, especially in the low energy regime. On the Other hand, at high energy, the Heisenberg correction term has less influence as a projectile momentum increase. We present the total cross sections of electron stripping, electron capture, and system breakdown in C5+ ions and Li2+ ions collisions with atomic hydrogen in the impact energy range from 10 keV to 160 keV, which is of interest in astrophysical plasmas, atmospheric sciences, plasma laboratories, and fusion research.

We investigate the shear quasinormal modes (QNMs) in the context of electron stars, focusing on the Lifshitz geometry and exploring the behavior in the small star limit. The study begins by analyzing the shear sector modes in the infrared (IR) Lifshitz limit, where the geometry approaches that of a pure Lifshitz space. We derive and solve the differential equations governing the shear modes, revealing the asymptotic behavior in terms of the Lifshitz exponent. In the special case of integer values of the exponent, we obtain analytic corrections to the solutions to extract hydrodynamical QNMs. We then explore the cases with a Lifshitz exponent equal to or greater than three, providing analytical corrections to the Lifshitz IR solutions. A special case with an exponent of two is also considered, leading to modified solutions. The study extends to finding hydrodynamical QNMs, emphasizing the role of the Lifshitz geometry. Further investigations involve the flux with real and complex frequencies, considering the off-shell Lagrangian and deriving conserved flux expressions. Our analysis focuses on the exterior of the star, modeled by the Reissner-Nordström-AdS geometry. The small star limit is examined, revealing interesting features in the behavior of fermionic excitations. In summary, we provide a detailed exploration of shear quasinormal modes in electron stars, shedding light on their behavior in Lifshitz geometry, small star limits, and the interplay between real and complex frequencies. Our findings contribute to our understanding of the dynamics of electron stars and their gravitational properties.

The energies of spin singlet and triplet bound electron pairs are reckoned for electrons interacting through the Coulomb interaction, while sitting on neigbouring lattice sites. It is concluded that triplet pairs are unlikely to be observed due to screening. The interplay of inter-electron couplings of different spatial range is investigated. High-pressure induced superconductivity is analysed and qualitative agreement is achieved with observed results by working out the dependence of the critical temperature on the microscopic parameters, characterising the electron motion. This approach can be applied to other kinds of inter-electron interactions.

In this paper, we propose an assumption of which the relation between electron and phonon is discussed and investigated based on the experiment of γ photon and electric interconverting with each other. We calculated the charge of a particular standing wave topology with Maxwell’s equation rotated in accordance space with the SO3 transformation. The derived charge value is 1.6035 × 10E−19C around 0.0826% different from the experimental data, indicating the proposal is a promising theory to explain the origin of charge and spin of electron particle. Electron spin angular momentum comes from the orbital angular momentum of photon rotation (electromagnetic field rotation), and electron charge comes from photon, that is, the space-time rotation effect of electromagnetic wave.

Our knowledge of electricity is based on two parallel lines of research: one focusing on ‘charge’, the other on ‘electron’. The distinction is blurred. The difficulty is that the fundamental nature of elementary charge is unknown. Here I present evidence that charge is a resting electron and electron is a moving charge – one physical entity two behavioural identities. That is, charge is nonrelativistic electron and electron is relativistic charge. Charges obey the laws of static electricity (electrostatics); electrons obey the laws of moving electricity (electrodynamics). Whether positive or negative, a charge is ejected from the atom at tremendous speed, losing the characteristics of ‘a charge’ and gaining those of ‘an electron’. I conclude that an atom, hence nature in general, contains an equal number of positive and negative electrons, recognised at rest as opposite charges. This solves the mystery of the electron-positron numerical asymmetry. It means that static positions and negatrons (charges) play equivalent roles as subatomic building blocks of matter, revealing a new atomic structure.

Accumulation of proteins in filter membranes limits the efficiently of filtering technologies for cleaning wastewater. Efforts are ongoing to coat commercial filters with different materials (such as titanium-dioxide, TiO2) in order to reduce the fouling of the membrane. Beyond monitoring the desired effect of retention of biomolecules, it is demanding to understand what are the biophysical changes in water-soluble proteins caused by interacting with the new coated filter membranes, an aspect that has received little attention so far. Using spin label electron paramagnetic resonance (EPR), aided with native fluorescent spectroscopy and dynamic light scattering (DLS), here we report the changes in the structure and dynamics of bovine serum albumin (BSA) exposed to TiO2 (P25) nanoparticles or passing through commercial polyvinylidene fluoride (PVDF) membranes coated with the same nanoparticles. We have found that the filtering process and prolongued exposure to TiO2 nanoparticles had significant effects on different regions of BSA, and denaturation of the protein was not observed, neither with TiO2 nanoparticles nor by pressing through TiO2-coated filter membranes.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

The redefined vacuum approach, which is frequently employed in the many-body perturbation theory, proved to be a powerful tool for formula derivation. Here, we elaborate this approach within the bound-state QED perturbation theory. In addition to general formulation, we consider the particular example of a single particle (electron or vacancy) excitation with respect to the redefined vacuum. Starting with simple one-electron QED diagrams, we deduce first- and second-order many-electron contributions: screened self-energy, screened vacuum polarization, one-photon exchange, and two-photon exchange. The redefined vacuum approach provides a straightforward and streamlined derivation and facilitates its application to any electronic configuration. Moreover, based on the gauge invariance of the one-electron diagrams, we can identify various gauge-invariant subsets within derived many-electron QED contributions.

With forty years of developments, bio-macromolecule cryo-electron microscopy has met its revolution of resolution and is playing a very important role in structural biology study. According to different specimen states, cryo-electron microscopy (cryo-EM) involves three specific techniques, single particle analysis (SPA), electron tomography and sub-tomogram averaging, and electron diffraction. All these three techniques have not realized their full potentials of solving structures of bio-macromolecules and therefore need to be developed in the future. In this review, the current existing bottlenecks of cryo-EM SPA are discussed with theoretical analysis, which includes air-water interface during specimen cryo-vitrification, bio-macromolecular conformational heterogeneity, focus gradient within thick specimen, and electron radiation damage. Besides, potential solutions of these bottlenecks are proposed and discussed, which are worthy of further investigations in the future.

Collisions of low energy electrons with molecules are important for understanding many aspects of the environment and technologies. Understanding the processes that occur in these types of collisions can give insights into plasma etching processes, edge effects in fusion plasmas, radiation damage to biological tissues and more. A radical update of the previous expert system for computing observables relevant to these processes, Quantemol-N, is presented. The new Quantemol Electron Collision (QEC) expert system simplifyies the user experience, improving reliability and implements new features. The QEC GUI interfaces the Molpro quantum chemistry package for molecular target setups and to the sophisticated UKRmol+ codes to generate accurate and reliable cross-sections. These include elastic cross-sections, super elastic cross-sections between excited states, electron impact dissociation, scattering reaction rates, dissociative electron attachment, differential cross-sections, momentum transfer cross-sections, ionization cross sections and high energy electron scattering cross-sections. With this new interface we will be implementing dissociative recombination estimations, vibrational excitations for neutrals and ions, and effective core potentials in the near future.

We have repeated the experiment performed recently by Krasznahorkay et al., (Phys. Rev. Lett. 116, 042501 (2016)), which may indicate a new particle called X17 in the literature. In order to get a reliable, and independent result, we used a different type of electron-positron pair spectrometer which have a more simple acceptance/efficiency as a function of the correlation angle, but the other conditions of the experiment were very similar to the published ones. We could confirm the presence of the anomaly measured at the Ex=18.15 MeV resonance, and also confirm their absence at the Ex=17.6 MeV resonance, and at Ep= 800 keV off resonance energies.

The mechanisms of formation of induced intrinsic and impurity radiative states, which consist of intrinsic and impurity electron-hole trapping centers in irradiated Ca2P2O7-Mn and Ca2P2O7 phosphates, were investigated using thermoactivation and vacuum-ultraviolet spectroscopy methods. These centers are excited at photon energies of 4.0 eV and 4.5 eV, which are within the matrix's transparency region. New radiative induced states at 3.06 eV and 2.92 eV are demonstrated to be generated upon the excitation of anions by photons with energies of 5.0 and 5.64 eV. This process is due to charge transfer from the ion to the impurities, specifically Mn^2+ O^2- Mn^2+ and the neighboring ion O^2- (P2O7)^4-. Furthermore, upon the excitation of matrix anions with photon energies exceeding the band gap (8.0 - 8.25 eV), electron trapping by impurities such as Mn^2+ and (P2O7)^4- ions results.

We explores the hydrodynamical limit of a homogeneous electron gas, considering the interplay between the infrared limit and phenomenological hydrodynamics. Our study involves interactions generated by non-linear coordinate transformations. The focus begins with an analysis of non-linear coordinate transformations and their impact on normal modes in a harmonic system. The Lagrangian for a harmonic oscillator is used as an illustrative example, highlighting the role of position-dependent effective mass in preventing certain coordinate values. Moving beyond single degrees of freedom, we extend the discussion to a system with several harmonic degrees of freedom, introducing a collective variable. The effective dynamics of this collective variable are defined through a Lagrange multiplier term, emphasizing linearity in the description. Our study extends to the Current Two-Point function (CTP) formalism, introducing matrices and their inverses, such as $\hD$ and $\hD^{-1}$. Further, we delve into the dynamics of current in a homogeneous electron gas at finite density and zero temperature. Green's functions are generated using a functional integral approach, and the effective action is constructed via functional Legendre transformation. The quadratic part of the generator functional is expanded to derive the effective action, leading to the Maxwell equation and the subsequent elimination of the photon field. The resulting effective action for current dynamics is expressed in terms of the Current Two-Point function, paving the way for further exploration of the hydrodynamical aspects of the electron gas. Our study combines theoretical developments and mathematical formalism to provide insights into the hydrodynamical behavior of homogeneous electron gases.

Electron can tunnel between cofactor molecules positioned along biological electron transport chains up to the distance of ≃20 Å on the millisecond time scale of enzymatic turnover. This tunneling range mostly determines the design of biological energy chains facilitating cross-membrane transport of electrons. Tunneling distance and cofactors’ redox potentials become main physical parameters of this design. The protein identity, flexibility, or dynamics are missing from this picture assigning universal charge-transport properties to all proteins. This paradigm is challenged by dynamical models of electron transfer showing that the hopping rate is constant within the crossover distance R*≃12 Å, followed with an exponential tunneling falloff at longer distances. In this view, energy chains for electron transport are best designed by placing redox cofactors near the crossover distance R*. Protein flexibility and dynamics affect the magnitude of the maximum hopping rate within the crossover radius. Protein charge transport is not driven by universal parameters anymore and protein identity matters.

In this review, photoinduced electron transfer processes in specifically designed assembled ar-chitectures have been investigated on the basis of recent results reported from our laboratories. A convenient and useful way to study these kinds of systems has been described in order to under-stand the rules that drive to a light induced charge separation and its subsequent decay to the ground state, also with the aim of offering a tutorial for young researchers. Assembled systems of covalent or supramolecular nature have been presented and some functional multicomponent systems for the conversion of light energy into chemical energy have been discussed.

Classical k-ratio models, e.g. ZAF and phi(rho z), used in electron probe microanalysis (EPMA) assume a homogeneous or multi-layered material structure, which essentially limits the spatial resolution of EPMA to the size of the interaction volume where characteristic x-rays are produced. We present a new model for characteristic x-ray emission that avoids assumptions on the material structure to not restrict the resolution of EPMA a-priori. Our model bases on the spherical harmonic (PN) approximation of the Boltzmann equation for electron transport in continuous slowing down approximation. PN models have a simple structure, are hierarchical in accuracy and well-suited for efficient adjoint-based gradient computation, which makes our model a promising alternative to classical models in terms of improving the resolution of EPMA in the future. We present results of various test cases including a comparison of the PN model to a minimum entropy moment model as well as Monte-Carlo (MC) trajectory sampling, a comparison of PN-based k-ratios to k-ratios obtained with MC, a comparison with experimental data of electron backscattering yields as well as a comparison of PN and Monte-Carlo based on characteristic X-ray generation in a three-dimensional material probe with fine structures.

Electrons moving at slow speeds much lower that the speed of light are described by a wave function which is a solution of Pauli’s equation. This is a low velocity limit of the relativistic Dirac equation. Here we compare two approaches, one which is the more conservative Copenhagen’s interpretation denying a trajectory of the electron but allowing a trajectory to the electron expectation value through Ehrenfest theorem. The said expectation value is of course calculated using a solution of Pauli’s equation. A less orthodox approach is championed by Bohm, and attributes a velocity field to the electron also derived from the Pauli wave function. It is thus interesting to compare the trajectory followed by the electron according to Bohm and its expectation value according to Ehrenfest. Both similarities and differences will be considered.

We report the electronic, magnetic and transport properties of a prototypical antiferromagnetic (AFM) spintronic device. We chose Cr as the active layer because it is the only room-temperature AFM elemental metal. We sandwiched Cr between two non-magnetic metals (Pt or Au) with large spin-orbit coupling. We also inserted a buffer layer of insulating MgO to mimic the structure and finite resistivity of a real device. We found that, while spin-orbit has a negligible effect on the current flowing through the device, the MgO layer plays a crucial role. Its effect is to decouple the Cr magnetic moment from Pt (or Au) and to develop an overall spin magnetization. We have also calculated the spin-polarized ballistic conductance of the device within the Büttiker-Landauer framework, and we have found that for small applied bias our Pt/Cr/MgO/Pt device presents a spin polarization of the current amounting to ~25%.

In order to study the effects of irradiation on the physicochemical properties and digestion behavior of chickpea protein, chickpea protein concentrate (CPC) was treated with electron beam irradiation (EBI) at doses of 5, 10, 15 and 20 kGy, respectively. After irradiation, protein solubility first increased at 10 kGy and 15 kGy, and then decreased at higher dose of 20 kGy. This was supported by SDS-PAGE where the intensity of major protein bands first increased and then decreased. Increased does of EBI generally led to greater oxidative modification of proteins in CPC, indicated by reduced sulfhydryls and increased carbonyls. In addition, protein structure was modified by EBI shown by Fourier transform infrared spectroscopy analysis where α-helix generally decreased and β-sheet increased. Although the protein digestibility was not significantly affected by EBI, the peptidomic analysis of the digests revealed significant difference among CPC irradiated with varying doses. A total of 337 peptides were identified from CPC irradiated with 0 kGy, 10 kGy and 20 kGy, respectively, with 18 overlapping peptides and 60, 29 and 40 peptides specific to the groups of 0, 10 and 20 kGy respectively. Theoretical calculation showed that the distribution of peptide length, hydrophobicity, net charge, and C-terminal residues were affected by irradiation. The 2, 2'-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging activity showed a marginal decrease with increasing dose of irradiation. In conclusion, EBI led to oxidative modification and structural changes of the chickpea protein, which subsequently affected the physicochemical properties of peptides obtained from in-vitro digestion of CPC despite of similar digestibility.

The critical role of global electron density transfer (GEDT) in increasing the reaction rate of polar organic reactions has been studied within the framework of Molecular Electron Density Theory (MEDT). To this end, the series of the polar Diels-Alder (P-DA) reactions of cyclopentadiene with cyanoethylene derivatives, for which experimental kinetic data are available, have been chosen. A complete linear correlation between the computed activation Gibbs free energies and the GEDT taking place at the polar transition state structures (TSs) is found; the higher the GEDT at the TS, the lower the activation Gibbs free energy. An interacting quantum atoms (IQA) energy partitioning analysis allows establishing a complete linear correlation between the electronic stabilization of the electrophilic ethylene frameworks and the GEDT taking place at the polar TSs. This finding supports Parr’s proposal for the definition of the electrophilicity  index (J. Am. Chem. Soc., 1999, 121, 1922). The present MEDT study allows establishing the critical role of the GEDT in the acceleration of polar reactions, since the electronic stabilization of the electrophilic framework with the electron density gain is greater than the destabilization of the nucleophilic one, making a net favorable electronic contribution to the decrease of the activation energy.

This research focuses on exploring generalized electron emissions in one-dimensional conducting materials, specifically examining field emission and thermionic emission. Additionally, the study investigates one-dimensional thermal radiation. The current density is derived for both one-dimensional thermionic emission and one-dimensional field emission. A generalized current density in one dimension is devised, taking into account arbitrary accelerating fields and temperature conditions. The formula for the one-dimensional current density is depicted with accelerating field and temperature across various work function materials. The current is also represented as a function of both temperature and electric field for various temperatures.

Over the past two decades, covalent organic frameworks (COFs) have become the most widely studied porous crystalline materials. Its specific physical and chemical properties are determined by the arrangement of atoms (crystal structure). Therefore, the determination of its structure is arguably the most important characterization step for COFs. Although single crystal X-ray diffraction (SCXRD) is the most widely used method for structure determination, the size of COF crystals is too small, or their crystal quality is so poor that confirmation of their structure is limited to lattice fringes by transmission electron microscopy (TEM). At present, many 2D-COFs have clear PXRD patterns, but not all 2D-COFs can obtain specific lattice fringes. This severely hinders the development of the COF field. Here, we discover the lattice shrinkage behavior of COFs under electron beam irradiation by comparing the lattice fringes of 2D-COFs under different conditions. By comparing the lattice fringes of TAPT-TFPT COF at room temperature and under liquid nitrogen freezing conditions, we found that the lattice fringes are in good agreement with the Powder X-ray diffraction (PXRD) and theoretical values of COF (2.213 nm) under freezing conditions, however, the lattice fringe spacing is only 1.656 nm at room temperature. The discovery not only provides new insights into the TEM characterization of COFs, but also further expands the range of crystalline COF materials.

Electroactive microorganisms have received a lot of interest in the field of environmental engineering and biotechnology because of their extracellular electron transfer (EET) capability of energy recovery and environmental remediation. However, the low efficiency of EET remains a barrier to its practical implementation. This review presents an introduction to EET, followed by addressing strategies for enhancing EET through different approaches including enhancing EET by mediator materials, external electricity, photo, and magnetism as well as integrated strategies, that is, the combination of multiple means to promote extracellular electron transport and improve the performance of microbial electrochemical systems. Finally, the challenges, perspectives, and new directions for EET enhancement will be discussed.

The generalized dual-kinetic-balance approach for axially symmetric systems is employed to solve the two-center Dirac problem. The spectra of one-electron homonuclear quasimolecules are calculated and compared with the previous calculations. The analysis of the monopole approximation with two different choices of the origin is performed. Special attention is paid to the lead and xenon dimers, Pb82+–Pb82+–e− and Xe54+–Xe54+–e−, where the energies of the ground and several excited σ-states are presented in the wide range of internuclear distances. The developed method provides the quasicomplete finite basis set and allows for construction of the perturbation theory, including within the bound-state QED.

In the Standard Model of elementary particles, the rest mass, magnetic moment and electric charge of the electron are considered to be natural constants. In this article it is proposed that these properties can be calculated in a simple way from the corresponding Planck units using the well-known period doubling phenomenon in nonlinear dynamical systems. Periods corresponding to the values of the electron and positron properties belong to a subset of stable periods. The periodic structures of the rest energy and magnetic moment consist of three internal degrees of freedom, whereas the Coulomb energy of the electric charge consists of four. The number of period doublings for the elementary charge determines the value of the fine structure constant alpha.

An analysis is presented of the possible existence of a second anomalous dipole moment of Dirac’s particle next to the angular one. It includes a discussion why, in spite of his own derivation, Dirac has doubted about its relevancy. It is shown why since then it has been overlooked and why it has vanished from leading textbooks. A critical survey is given on the reasons of its reject, including the failure of attempts to measure and the perceived violations of time reversal symmetry and chargeparity symmetry. It is emphasized that the anomalous electric dipole moment of the pointlike electron (AEDM) is fundamentally different from the quantum field type electric dipole moment of an electron (eEDM) as defined in the standard model of particle physics and that its measurement requires different instrumentation. A proposal has been described how to prove or disprove its existence by experiment. Moreover, by reference from literature, the possible impact is discussed in the nuclear domain and in the gravitational domain.

A rigorous model for the electron is presented by generalizing the Coulomb's Law or Gauss's Law of electrostatics, using a unified theory of electricity and gravity. The permittivity of the free-space is allowed to be variable, dependent on the energy density associated with the electric field at a given location, employing generalized concepts of gravity and mass/energy density. The electric field becomes a non-linear function of the source charge, where concept of the energy density needs to be properly defined. Stable solutions are derived for a spherically symmetric, surface-charge distribution of an elementary charge. This is implemented by assuming that the gravitational field and its equivalent permittivity function is proportional to the energy density, as a simple first-order approximation, with the constant of proportionality referred to as the Unifield Electro-Gravity (UEG) constant. The stable solution with the lowest mass/energy is assumed to represent a ``static'' electron without any spin. Further, assuming that the mass/energy of a static electron is half of the total mass/energy of an electron including its spin contribution, the required UEG constant is estimated. More fundamentally, the lowest stable mass of a static elementary charged particle, its associated classical radius, and the UEG constant are related to each other by a dimensionless constant, independent of any specific value of the charge or mass of the particle. This dimensionless constant is numerologically found to be closely related to the the fine structure constant. This possible origin of the fine structure constant is further strengthened by applying the proposed theory to successfully model the Casimir effect, from which approximately the same above relationship between the UEG constant, electron's mass and classical radius, and the fine structure constant, emerges.

Real-time evolution of the electron densities under excitations in La₂CuO₄ was calculated by the time-dependent density functional theory (TDDFT). The author found, for the first time, under excitations, the electron cloud of Cu²⁺ changes obviously and the characteristic frequencies are 83 meV and 36 meV, respectively, for two different modes. The results are unexpected and close to that of lattice vibrations. The results show that the electron cloud of Cu²⁺ (just like the lattice) can be the electron-pairing medium in high temperature copper oxide superconductors.

This work communicates results from optical emission spectroscopy following laser-induced optical breakdown at or near nanomaterial. Selected atomic lines of silver are evaluated for consistent determination of electron density. Comparisons are presented with Balmer series hydrogen results. Of particular interest are measurements free of self-absorption effects. For several silver lines, asymmetries are observed in the recorded line profiles. Electron densities of interest range from 0.5 to 3 × 10¹⁷ cm^-3, for 5 nanosecond Q-switched Nd:YAG radiation at wavelengths of 1064, 532, and 355 nm, and for selected silver emission lines including 328.0, 338.2, 768.7, and 827.3 nm, and the hydrogen alpha Balmer series line at 656.3 nm. Line asymmetries are presented for the 328.0 nm Ag I line that is measured following generation of the plasma due to multiple photon absorption. This work explores electron density variations for different irradiance levels, and reports spectral line asymmetry of resonance lines for different laser fluence levels.

Nanoparticles -- regularly patterned or randomly dispersed -- are a key ingredient for emerging technologies in photonics. Of particular interest are scattering and field enhancement effects of metal nanoparticles for energy harvesting and converting systems. An often neglected aspect in the modeling of nanoparticles are light interaction effects beyond classical electrodynamics stemming from electron dynamics in confined and accelerated systems. We give a detailed account on free electron phenomena in metal nanoparticles and discuss analytic expressions, stemming from microscopic and semi-classical theories. These can improve standard computational schemes to produce more reliable results on the optical properties of metal nanoparticles. We combine these solutions into a single framework and study their joint impact on isolated Au, Ag, and Al nanoparticles as well as dimer structures.

The superconductivity of CaC6 as a function of pressure and of abundant Ca isotopes is revisited using DFT calculations on a 2c – double hexagonal superlattice. The introduction of superlattices is motivated by previous synchrotron absorption and Raman spectroscopy results on other superconductors that show evidence of superlattice vibrations at low (THz) frequencies. A 2c superlattice for CaC6 is illustrative of atomic orbital symmetry and periodicity, including bonding and antibonding s-orbital character implied by cosine modulated electronic bands. Inspection of the cosine band reveals that the cosine function has a small (meV) energy difference between bonding and antibonding regions relative to a midpoint non-bonding energy. Fermi surface nesting is apparent in an appropriately folded Fermi surface using a superlattice construct. Nesting relationships identify phonon vectors for conservation of energy and for phase coherency between coupled electrons at opposite sides of the Fermi surface. Detailed analysis of this Fermi surface nesting provides accurate estimates of the superconducting gaps for CaC6 with change in applied pressure. Recognition of superlattices within a rhombohedral or hexagonal representation provides consistent mechanistic insight on superconductivity and electron−phonon coupling in CaC6.

We propose a description of the electromagnetic field in the form of a four-component complex spinor, from which a vector of electromagnetic potential with two degrees of freedom, calibrated by two conditions - zero length and zero component along the y-axis - is obtained by using Pauli matrices. A similar approach is applied to the field of a fermion, in particular, the electron. It is known that the quantum field of the electron and the electron itself is a four-component complex spinor, so, existing in the Minkowski vector space, we cannot observe it directly. But with the help of Pauli matrices a vector is formed from the electron spinor, which is known to us as an electric current vector, and this current vector describes exactly a single particle. As a vector, it is available to us for observation in our vector space. Similarly, the electromagnetic field and its photon particle is also a four-component spinor, from which the universal formula using Pauli matrices produces a vector, it is known to us as the electromagnetic potential vector, and it too describes even a single photon. All the differences in the properties of the current vector and the electromagnetic potential vector, and hence the electron and the electromagnetic field, are due only to a slight difference in the structures of their four-component spinors and inextricable linked to them momentum spinors and coordinate spinors. Expressions for the electric and magnetic fields of a photon during its interaction with an electron.Thus, a unified way to describe bosons and fermions in spinor space is proposed. Each spinor using the same formula corresponds to a vector, in the case of a fermion it is a current vector, in the case of a boson it is a vector, for example, of the electromagnetic potential. Each spinor of a field is matched with a spinor of coordinates and a spinor of momentum, which are transformed by the same Lorentz transformations and which have the same structure as their corresponding field spinor, that is, the momentum and coordinates of boson have a bosonic spinor structure, while momentum and coordinates of fermion are a spinor with a fermionic structure. Field, coordinates and momentum vectors of boson automatically have a zero length, while in the case of fermion they all have a nonzero length, so the fermion, in contrast to the boson, has a nonzero mass, nonzero charge and moves with a sub light speed.While quantum mechanics treats probability as a real number, quantum field theory deals with probability as a four-dimensional real vector. The place of the probability amplitude, which in quantum mechanics is a complex number, in quantum field theory is taken by a complex spinor.In the same way as in quantum mechanics the processes of propagation and interaction are described at the level of complex probability amplitudes, and the final result is translated into a real probability value, so in quantum field theory all processes should be described in terms of complex spinor space, and the result is translated into the form of a real vector in Minkowski space.The presented approach, at its proper development, makes it possible to carry out calculations of the interaction of particles in two-dimensional spinor space, and to interpret in terms of the Minkowski vector space only the final results.

A topological quantum interplay between the magnetic flux and the mass has been investigated, for the case of an electron, by evaluating a gauge-invariant phase factor (a Wilson loop) linked to the electromagnetic gauge field of the particle. In particular, from this phase factor and the quantization of the magnetic flux variations, a relationship between the mass at rest of the electron and its self-energy , arising from radiative corrections, has been obtained also within a QED approach. Besides, a formulation of an energy scale comparable to the energy at rest of an electron-positron pair is proposed. Remarkably, a reckoning of the Bohr energy of a W⁺ W^- pair is compatible with constants and parameters usually employed within the electroweak theory and comparable to the energy at rest of an electron-positron pair.

Friction and wear take place on two solid surfaces in sliding contact as a result of the mechanical, thermal and chemical interactions with the participation of environmental species. Electron microscopy and the associated spectroscopic analyses are powerful in probing these mechanisms in spatial resolutions from micro to atomic scale. This article provides a review of the author’s work in the wear and friction mechanisms of PVD hard coatings in which various SEM- and TEM-based microscopic and spectroscopic techniques were employed. Understanding on the failure mechanisms and the origin of self-adaptive friction has been improved to nano-scale. Other related issues are also discussed, such as sample preparation techniques for cross-sectional electron microscopy, energy dispersive X-ray spectroscopy and electron energy loss spectroscopy.

This article develops a multi-perspective view on motivations and methods for tobamovirus purification through the ages, and presents a novel efficient, easy-to-use approach that can be well-adapted to different species of native and functionalized virions. We survey the various driving forces prompting researchers to enrich tobamoviruses: from the search for the causative agents of mosaic diseases in plants to their increasing recognition as versatile nanocarriers in biomedical and engineering applications. Best practice and also rarely applied options for the serial processing steps required for successful isolation of tobamoviruses are then reviewed. Adaptations for distinct particle species, pitfalls and 'forgotten' or underrepresented technologies are considered as well. The article is topped off with our own development of a method for virion preparation, rooted in historical protocols. It combines selective re-solubilization of polyethylene glycol (PEG) virion raw precipitates with density step gradient centrifugation in biocompatible iodixanol formulations, yielding ready-to-use particle suspensions. This newly established protocol and some considerations for perhaps worthwile further developments could serve as putative stepping stones towards preparation procedures appropriate for routine practical uses of the multivalent soft-matter nanorods.

Superscaling in electron scattering from nuclei is re-examined paying special attention to the definition of the averaged single-nucleon responses. The validity of the extrapolation of nucleon responses in the Fermi gas has been examined, which previously lacked a theoretical foundation. To address this issue, we introduce new averaged responses with a momentum distribution smeared around the Fermi surface, allowing for momenta above the Fermi momentum. This approach solves the problem of negativity in the extrapolation away from the scaling region and, at the same time, validates its use in the scaling analysis. This work has important implications for the interpretation of scaling data and contributes to the development of a more complete understanding of the scaling approach.

Although good field emission from graphene has been demonstrated from a wide variety of different microfabricated structures, very few of them can be used to improve the design of cold field emitters for electron microscopy applications. Most of them consist of densely packed nano-emitters, which produce a large array of defocused overlapping electron beams, and therefore cannot be subsequently focused down to a single nanometer electron probe. This paper reviews the kind of single-tip cathode structures suitable in cold field emission guns for instruments such as scanning electron microscopy, transmission electron microscope or scanning transmission electron microscopy, and reviews progress in fabricating them from graphene-based materials.

We discuss the implementation of a suite of virtual diagnostics at the FACET-II facility currently under commissioning at SLAC National Accelerator Laboratory. The diagnostics will be used for prediction of the longitudinal phase space along the linac, spectral reconstruction of the bunch profile and non-destructive inference of transverse beam quality (emittance) using edge radiation at the injector dogleg and bunch compressor locations. These measurements will be folded in to adaptive feedbacks and ML-based reinforcement learning controls to improve the stability and optimize the performance of the machine for different experimental configurations. In this paper we describe each of these diagnostics with expected measurement results based on simulation data and discuss progress towards implementation in regular operations.

Some contaminants of emerging concern (CECs) are known to survive conventional wastewater treatment plants, which introduce them back to the environment and can potentially cycle up in drinking water supplies. This is especially concerning because of the inherent ability of some CECs to induce physiological effects in humans at very low doses. Advanced oxidation processes (AOPs) such as TiO2 based photocatalysis are of prominent interest for addressing CECs in aqueous environments. Natural water resources often contain dissolved metal cations concentrations in excess of targeted CEC concentrations. These cations may significantly, adversely impact degradation of CECs by scavenging TiO2 surface generated electrons. Consequently, simple pseudo first order or Langmuir-Hinshelwood kinetics are not sufficient for reactor design and process analysis in some scenarios. Rhodamine B dye and dissolved copper cations were studied as reaction surrogates to demonstrate that TiO₂ catalyzed degradation for very dilute solutions is very nearly completely due to homogeneous reaction with hydroxyl radicals and that in this scenario the hole trapping pathway has negligible impact. Chemical reaction kinetic studies were then carried out to develop a robust model for RB/metal reactions that is exact in the electron pathways for hydroxyl radical production and metal scavenging.

In particle physics, spin is an intrinsic form of angular momentum carried by the elementary particles. It is believed that spin is a solely quantum-mechanical phenomenon, which does not have a counterpart in classical mechanics. We have derived the simplest equations of spin and magnetic moment of a charged elementary particle. These formulas enable us to understand the physical nature of the spin and the structure of elementary particles. It is shown that the electron and muon are in the shape of a thin ring with a circular cross section (torus), and the proton is in the form of a ring with a non-circular cross section (toroid). The connection between the photon’s spin of and the propagation of electromagnetic waves is considered.

Point-contact spectroscopy has been performed on bulk samples of electron-doped high temperature superconductor Nd2-xCexCuO4-. The samples were characterized by X-ray diffraction and scanning electron microscopy equipped with a wavelength dispersive spectrometer and an electron backscatter diffraction detector. The samples with a Ce content x = 0.15, show the absence of spurious phases and randomly oriented grains, most of which have dimensions of approximately 220 µm2. The low-bias spectra in the tunnelling regime, i.e., high transparency interface, exhibit a gap feature at about ±5 meV and no zero-bias conductance, consistent with the most literature data on oriented samples. The high-bias conductance has also been measured in order to obtain information on the properties of the barrier. A V-shape has been in some cases observed, instead of the parabolic behavior expected for tunnel junctions.

To obtain a given structure in 3D building-up modes, it is necessary to use optimal surfacing modes that determine the amount of heat input in local areas. For this purpose, aluminum bronze was surfacing onto a deformed base and the structure and its characteristics in the surfacing and heat-affected zones were studied by the EBSD method. The heterogeneity of the formation of the structure in each selected zone is established, which indicates the heterogeneity of heat input in local areas of the material in one mode of surfacing. For typical cases of crystallization, a molecular dynamics simulation of crystallization processes with different heat input to the base with characteristics specified based on experimental data was carried out. It has been established that the amount of heat input determines the degree of melting and the inherited defectiveness of growing crystals. The formation of misorientation boundaries and crystallization centers of new grains is determined by the conditions of joint growth of grains with given crystallographic parameters of the computational model. Numerical calculations agree with the experimentally observed results.

Metal-organic frameworks (MOFs), composed of metal nodes and inorganic linkers are promising for a wide range of applications due to their unique periodic frameworks that can be flexibly tuned. Understanding of the structure-activity relationships can facilitate the development and application of MOFs nanomaterials. Transmission electron microscopy (TEM) is a one-of-a-kind technique capable of characterizing MOFs microstructures at the atomic scale. Besides, in-situ TEM set-ups make it possible to direct visualize the microstructural evolution of MOFs in real time, which enables monitoring transitions of MOFs during growth as well as under working conditions. However, MOFs are so sensitive to the high-energy electron beam which makes TEM-based characterizing methods challenging. In this review, we first introduce the main damage mechanisms for MOFs under electron beam irradiation and two strategies to minimize the damages: low-dose TEM and cryo-TEM. Then, we discuss the techniques combined with the two strategies to analyze the MOFs’ microstructure, including three-dimensional electron diffraction, direct detection electron counting camera, and iDPC-STEM. Groundbreaking milestones and research advances with respect to static characterization of MOFs structures are highlighted. In-situ TEM studies are exemplary reviewed to provide insights into MOFs dynamics induced by various stimuli. Additionally, perspectives on promising techniques that may further facilitate the MOFs study using TEM are analyzed.

The entropy of a system gives a powerful insight into its microscopic degrees of freedom, however standard experimental ways of measuring entropy through heat capacity are hard to apply to nanoscale systems, as they require the measurement of increasingly small amounts of heat. Two alternative entropy measurement methods have been recently proposed for nanodevices: through charge balance measurements and transport properties. We describe a self-consistent thermodynamic framework for treating few-electron nanodevices which incorporates both existing entropy measurement methods, whilst highlighting several ongoing misconceptions. We show that both methods can be described as special cases of a more general relation and prove its applicability in systems with complex microscopic dynamics – those with many excited states of various degeneracies.

Direct electron transfer (DET)-type bioelectrocatalysis, which couples electrode reactions and catalytic functions of redox enzymes without any redox mediator, is one of the most intriguing subjects studied over the past decades in the field of bioelectrochemistry. In order to realize the DET-type bioelectrocatalysis and to improve the performance, nanostructures of the electrode surface have to be carefully tuned for each enzyme. In addition, enzymes can also be tuned by protein engineering approach for the DET-type reaction. This review summarizes the resent progresses in this field of the research, while taking into consideration of the importance of nanostructure of electrodes as well as redox enzymes. Described are basic concepts and theoretical aspects of DET-type bioelectrocatalysis, significance of nanostructures as scaffolds for DET-type reactions, protein engineering approached for DET-type reactions, and concepts and facts of bidirectional DET-type reactions, from a cross-disciplinary viewpoint.

In the succinic acid-producing bacterium Pseudoclostridium thermosuccinogenes the fumarate reductase (FRD) genes reside in an operon together with those encoding an electron bifurcating complex (FlxABCD-HdrABC) that shuttles electrons from NADH to ferredoxin and a disulfide bond. Based on phylogeny and genomic co-occurrence we propose two hypothetical mechanisms via which the FRD is involved in electron bifurcation: (I) A disulfide bond from a hitherto unknown cofactor is reduced by the electron-bifurcating FlxABCD-HdrABC complex, using NADH to generate two thiol groups, while facilitating the unfavourable reduction of ferredoxin by NADH. The disulfide bond is subsequently regenerated via the reduction of fumarate by the FRD using the previously formed thiol groups. (II) The FRD forms an integral part of the FlxABCD-HdrABC complex, and NADH is used to reduce ferredoxin and fumarate directly, without an intermediate disulfide-forming cofactor. Either way enables the conservation of additional energy by a soluble FRD, analogous to fumarate respiration.

Microbial-mediated biogeochemical cycling of iron is widespread in anaerobic environments such as sediments and deep Earth aquifers, and is one of the major pathways for metabolising iron in nature. Organic matter containing quinone groups can act as electron shuttles to transfer electrons between microorganisms and Fe(III) oxides, facilitating the biotransformation of iron; this process also influences the transport transformation of pollutants. In this paper, the reduction of Fe(III) oxides by aniline in the heterogeneous iron-reducing bacterium Shewanella oneidensis MR-1 mediated by the electron shuttle AQS was investigated. The results showed that aniline significantly promoted the reduction of Fe(III) by MR-1 in the AQS-mediated reaction, and the best Fe(III) reduction was achieved in the reaction group of "GT+MR-1+0.5mM AQS+3μM aniline", in which the Fe(II) production was significantly higher than that in the reaction groups of only microorganisms and no aniline reaction. The amount of Fe(II) produced was significantly higher than that of the microorganism-only and aniline-free reaction groups, and the addition of aniline also significantly increased the consumption of sodium lactate by MR-1 in the reaction system. The solid mineral Fe(II)-O content increased to 41.32% after the reaction. However, the structure of needle ferrite is relatively stable, and the surface morphology did not change significantly by SEM, and the generation of other secondary minerals was not observed in the XRD results. The results of this experimental study can help to understand the biogeochemical cycle of iron in multicomponent reactions and are of great significance for environmental management.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

A quantitative analysis of X-ray emission from an electron cyclotron resonance (ECR) plasma was performed to probe the spatial properties of electrons having energy for effective ionisation. A series of measurements were taken by INFN-LNS and ATOMKI, capturing spatially and spectrally resolved X-ray maps as well as volumetric emissions from argon plasma. Comparing the former with model generated maps (involving space-resolved phenomenological electron energy distribution function and geometrical efficiency calculated using ray-tracing MC routine) furnished information on structural aspects of the plasma. Similarly, fitting a model composed of bremsstrahlung and fluorescence to the volumetric X-ray spectrum provided valuable insight into the density and temperature of confined and lost electrons. The latter can be fed back to existing electron kinetics models for simulating more relevant energies, consequently improving theoretical X-ray maps and establishing the method as an excellent indirect diagnostic tool for warm electrons, required for both fundamental and applied research in ECR plasmas.

A new approach to fabricate TiNi surfaces combining the advantages of both monolithic and porous materials for implants is used in this work. New materials were obtained by depositing a porous TiNi powder onto monolithic TiNi plates followed by sintering at 1200°C. Then, further modification of the material surface with a high-current-pulsed electron beam (HCPEB) was carried out. Three materials obtained (one after sintering and two after subsequent beam treatment by 20 and 30 pulses, respectively) were studied by XRD, SEM, EDX, EIS methods, profilometry and OCP measurements. Structural and compositional changes caused by HCPEB treatment were investigated. Surface properties of the samples during their storage in saline for 10 days were studied and a model experiment with cell growth (MCF-7) was carried out for the sample unmodified with electron beam to detect cell appearance on different surface locations.

The emission of [O I] lines in the coma of Comet 67P/Churyumov-Gerasimenko during the Rosetta mission have been explained by electron impact dissociation of water rather than the process of photodissociation. This is the direct evidence for the role of electron induced processing has been seen on such a body. Analysis of other emission features is handicapped by a lack of detailed knowledge of electron impact cross sections which highlights the need for a broad range of electron scattering data from the molecular systems detected on the comet. In this paper we present an overview of the needs for electron scattering data relevant for the understanding of observations in coma, the tenuous atmosphere and on the surface of 67P/Churyumov-Gerasimenko during the Rosetta mission. The relevant observations for elucidating the role of electrons come from optical spectra, particle analysis using the ion and electron sensors and mass spectrometry measurements. To model these processes electron impact data should be collated and reviewed in an electron scattering database and an example is given in the BEAMD, which is a part of a larger consortium of Virtual Atomic and Molecular Data Centre – VAMDC.

Laser irradiation of metals is widely used in research and applications. In this work, we study how the material geometry affects electron-phonon coupling in nano-sized gold samples: an ultrathin layer, nano-rod, and two types of gold nanoparticles: cubic and octahedral. We use the combined tight-binding molecular dynamics Boltzmann collision integral method implemented within XTANT-3 code to evaluate the coupling parameter in irradiation targets at high electronic temperatures (up to Te~20,000 K). Our results show that the electron-phonon coupling in all objects with the same fcc atomic structure (bulk, layer, rod, cubic and octahedral nanoparticles) is nearly identical at electronic temperatures above Te~7000 K, independently of geometry and dimensionality. At low electronic temperatures, reducing dimensionality reduces the coupling parameter. Additionally, nano-objects under ultrafast energy deposition experience nonthermal damage due to expansion caused by electronic pressure, in contrast to bulk metal. Nano-object ultrafast expansion leads to ablation/emission of atoms, and disorder inside of the remaining parts. These nonthermal atomic expansion and melting are significantly faster than electron-phonon coupling, forming a dominant effect in nano-sized gold.

The elimination of superoxide radical anions (O2•−) by 5-amino-2-hydroxybenzoic acid (mesalazine, 5-ASA), 4-amino-2-hydroxybenzoic acid (4-ASA), and related compounds used for ulcerative colitis treatment was investigated using cyclic voltammetry and electron spin resonance (ESR) analyses aided by density functional theory (DFT) calculations. Quasi-reversible O2/O2•− redox was found to be modified by the compounds, suggesting that an acid-base reaction in which a hydroperoxyl radical (HO2•) is formed from O2•− occurs. However, the deprotonated 5-ASA anion can eliminate O2•− through proton-coupled electron transfer (PCET), forming a radical product. This electron transfer (ET) was confirmed by ESR analysis. The 4-aminophenol moiety in 5-ASA plays an important role in the PCET involving two proton transfers and one ET based on -conjugation. The electrochemical and DFT results indicated that O2•− elimination by 5-ASA proceeds efficiently viathrough the PCET mechanism after deprotonation of the 1-carboxyl group. Thus, 5-ASA may act as an anti-inflammatory agent in the alkali intestine through PCET-based O2•− elimination.

The solute carrier family 25 (SLC25) participates in the transport of metabolites and cofactors across the membranes of mitochondria, plastids, peroxisomes, and endoplasmic reticulum. By calling for genomic blocks involved in adjacent metabolic reactions, this report introduces gene clusters of the Slc25 subfamily 44, stilbene and chalcone synthases, and subunits of the mitochondrial electron transfer complexes. The Slc25A44 gene was found ubiquitously expressed and transcriptionally co-regulated with energy metabolism genes in human, mouse, and Arabidopsis thaliana. The Slc25A44s also had no homozygous missense mutation and were highly conserved at intra-species level with the majority of polymorphism present in the non-coding regions. When expressed in oocytes, AdSlc25A44 from Arachis duranensis showed transport activity for the common precursors of flavonoids, stilbenoids, and ubiquinone. Accordingly, AdSLC25A44 and its human orthologue HsSLC25A44 elevated the production of para-coumaric, 4-aminobenzoic, and 4-hydroxybenzoic acids in Saccharomyces cerevisiae strains designed to produce para-coumaric acid via different pathways. Moreover, the engineered SLC25 subfamily specific signature, i.e., AdSLC25A44^LWW206IQF, had a stronger effect on para-coumaric acid secretion than the native variant. Importantly, the aerobic growth-rate of S. cerevisiae was significantly higher when expressing the AdSLC25A44, HsSLC25A44, or AdSLC25A44^LWW206IQF. These results suggest that SLC25A44 is an essential mitochondrion-ER-nucleus zone transporter associated with metabolism of secondary metabolites and energy.

We put forward a co-axial pump(optical)-probe(X-rays) experimental concept and show performance of the optical component. A Bessel beam generator with a central 100 micrometers-diameter hole (on the optical axis) was fabricated using femtosecond (fs) laser structuring inside a silica plate. This flat-axicon optical element produces a needle-like axial intensity distribution which can be used for the optical pump pulse. The fs-X-ray free electron laser (X-FEL) beam of sub-1 micrometer diameter can be introduced through the central hole along the optical axis onto a target as a probe. Different realisations of optical pump are discussed. Such optical elements facilitate alignment of ultra-short fs-pulses in space and time and can be used in light-matter interaction experiments at extreme energy densities on the surface and in the volume of targets. Full advantage of ultra-short 10 fs X-FEL probe pulses with fs-pump(optical) opens an unexplored temporal dimension of phase transitions and the fastest laser-induced rates of material heating and quenching. A wider field of applications of fs-laser-enabled structuring of materials and design of specific optical elements for astrophotonics is presented.

The radiosensitivity of biological systems is strongly affected by the system oxygenation. On the nanoscopic scale and molecular level, this effect is considered to be strongly related to the indirect damage of radiation. Even though particle track radiolysis has been the object of several studies, still little is known about the nanoscopic impact of target oxygenation on the radical yields. We present here an extension of the chemical module of the Monte Carlo particle track structure code TRAX, taking into account the presence of dissolved molecular oxygen in the target material. The impact of the target oxygenation level on the chemical track evolution and the yields of all the relevant chemical species is studied in water under different irradiation conditions: different linear energy transfer (LET) values, different oxygenation levels, and different particle types. Especially for low LET radiation, a large production of two highly toxic species (HO₂^• and O₂^•− ), which are not produced in anoxic conditions, is predicted and quantified in oxygenated solutions. The remarkable correlation between the HO₂^• and O₂^•− production yield and the oxygen enhancement ratio observed in biological systems suggests a direct or indirect involvement of HO₂^• and O₂^•− in the oxygen sensitization effect. The results are in agreement with available experimental data and previous computational approaches. An analysis of the oxygen depletion rate in different radiation conditions is also reported.

We study the performance of a classical and quantum magnetic Otto cycle with a quantum dot as a working substance using the Fock-Darwin model with the inclusion of the Zeeman interaction. Modulating an external/perpendicular magnetic field, we found in the classical approach an oscillating behavior in the total work that is not perceptible under the quantum formulation. Also, we compare the work and efficiency of this system for different regions of the Entropy, $S(T,B)$, diagram where we found that the quantum version of this engine always shows a reduced performance in comparison to his classical counterpart.

We have investigated the effect of electron-beam irradiation by a forevacuum-pressure plasma-cathode electron source on the surface roughness and hardness of Al2O3- and AlN-based ceramics. The roughness increases with increasing temperature of the processed surface, while the hardness slightly decreases. For aluminum nitride ceramic, we find that the thermal conductivity increases by a factor of 1.5 to 2 depending on the electron-beam irradiation regime.

We present a model that incorporates the effect of two-body currents in quasielastic electron-nucleus scattering within the framework of a consistent superscaling formalism. This is achieved by defining an averaged single-nucleon hadronic tensor based on the 1p1h matrix element of the one-body current plus meson-exchange currents (MEC). The consistent treatment of one- and two-body currents in our model enables the calculation of exchange current effects in the kinematical region where the Fermi gas response is zero, but not the scaling function. The effect of MEC is consistently taken into account when extracting the phenomenological scaling function from electron scattering data. With this model, we investigate the effect of MEC on the response functions taking into account the effective mass of the nucleon, and examine the consequences it has on the inclusive (e,e′) cross section. We find that 1p1h MEC deplete the quasielastic transverse response, while they not alter significantly the scaling behavior of (e,e′) data.

Powerful emitters of the ultraviolet C (UVC) light in the wavelength range of 230-280nm are necessary for the development of effective and safe optical disinfection technologies, high-sensitive optical spectroscopy and non-line-of-sight optical communication. This review considers such UVC-emitters with electron-beam pumping of heterostructures with quantum wells in the (Al,Ga)N material system. The important advantages of these emitters include the absence of the critical problem of p-type doping and the possibility of achieving record (up to several tens of watts for peak values) output optical power values in the UVC range. The review consistently considers about a decade of world experience in the implementation of various UV emitters with various types of thermionic, field-emission, and plasma-cathode electron guns (sources) used to excite various designs of active (light-emitting) regions in heterostructures with quantum wells AlxGa1-xN/AlyGa1-yN (x = 0 − 0.5, y = 0.6 − 1) fabricated either by metal-organic chemical vapor deposition or by plasma-activated molecular beam epitaxy. Special attention is paid to the production of heterostructures with multiple quantum wells/two-dimensional(2D) quantum disks GaN/AlN with a monolayer (1ML ~ 0.25nm) thickness, which ensures a high internal quantum efficiency of radiative recombination in the UVC range, low elastic stresses in heterostructures, and a high output UVC-optical powers.

Single particle analysis with cryogenic electron microscopy (cryo-EM) can determine high resolution structures of macromolecular assemblies. To reconstruct final three-dimension(3D) density map, a reliable initial model is essential and ab-initio reconstruction usually can avoid model bias. The grand challenge for ab-initio reconstruction is to alignment two-dimension(2D) low signal-to-noise ratio(SNR) of particle images with random and unknown parameters. Here we formulate a fast ab initio reconstruction method(named AlignFM) based on Fourier Mellin transform and particle-swarm intelligence optimization(PSO) algorithm. It enables simultaneous 2D alignment and 3D refinement, which can fast generate a reliable 3D map. After experiments on several real datasets. AlignFM shows high performance on fast ab initio reconstruction with a small amount of data.

In this paper, we have constructed a WKB approximation for graphene having a Y-shaped Kekul\'e lattice distortion and a special folding of the $\mbox{\boldmath$K$}$ and $\mbox{\boldmath$K$}^\prime$ valleys, which leads to very specific linear energy dispersions with two non-equivalent pairs of subbands. These obtained semi-classical results, which include the action, electron momentum and wave functions, are utilized to analyze the dynamics of electron tunneling through non-square potential barriers. In particular, we explore resonant scattering of an electron by a potential barrier built on Kekul\'e-distorted graphene. Mathematically, a group of consecutive equations for a semi-classical action have been solved by following a perturbation approach under the condition of small strain-induced coupling parameter $\Delta_0 \ll 1$ (a good fit to its actual value $\Delta_0 \backsim 0.1$). Specifically, we consider a generalized model for Kek-Y graphene with two arbitrary Fermi velocities. The dependence of the electron transmission amplitude on the potential profile $V(x)$ and band parameters of Kekul\'e-patterned graphene has been explored and analyzed in details.

The ionic Diels-Alder (I-DA) reactions of a series of six iminium cations with cyclopentadiene have been studied within the Molecular Electron Density Theory (MEDT). The superelectrophilic character of iminium cations,  > 8.20 eV, accounts for the high reactivity of these species participating in I-DA reactions. The activation energies are found between 13 and 20 kcal·mol-1 lower in energy than those associated to the corresponding Diels-Alder (DA) reactions of neutral imines. These reactions are low endo selective as a consequence of the cationic character of the TSs, but highly regioselective. Solvents have poor effects on the relative energies, and an unappreciable effect in the geometries. In dichloromethane the activation energies increase slightly as a consequence of the better solvation of the iminium cations than the cationic TSs. ELF topological analysis of the bonding changes along the I-DA reactions shows that they are very similar to those in polar DA reactions. The present MEDT study makes it possible establishing that the global electron density transfer (GEDT) taking place at the TSs of I-DA reactions, and not steric (Pauli) repulsions such as have been recently proposed, are responsible for the features of these type of DA reactions.

Much has been learned about the interaction between myosin and actin through biochemistry, in vitro motility assays and cryo-electron microscopy of F-actin decorated with myosin heads. Comparatively less is known about actin-myosin interactions within the filament lattice of muscle, where myosin heads function as independent force generators and thus most measurements report an average signal from multiple biochemical and mechanical states. All of the 3-D imaging by electron microscopy that has revealed the interplay of the regular array of actin subunits and myosin heads within the filament lattice has been accomplished using the flight muscle of the large waterbug Lethocerus sp. Lethocerus flight muscle possesses a particularly favorable filament arrangement that enables all the myosin cross-bridges contacting the actin filament to be visualized in a thin section. This review covers the history of this effort and the progress toward visualizing the complex set of conformational changes that myosin heads make when binding to actin in several static states as well as fast frozen actively contracting muscle. The efforts have revealed a consistent pattern of changes to the myosin head structures determined by X-ray crystallography needed to explain the structure of the different acto-myosin interactions observed in situ.

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

The influence of various energetic particles and electron injection on transport of minority carriers and non-equilibrium carrier recombination in Ga₂O₃ is summarized in this review. In Ga₂O₃ semiconductor, if robust p-type material and bipolar structures become available, diffusion length of minority carriers will be of critical significance. Diffusion length of minority carriers dictates functionality of such electronic devices as diodes, transistors, and detectors. One of the problems in ultra-wide band gap materials technology, is the short carrier diffusion length, due to scattering on extended defects. Electron injection in n- and p-type Gallium Oxide results in a significant increase of the diffusion length, even after its deterioration due to exposure to alpha- and proton-irradiation. Furthermore, post electron injection diffusion length in irradiated material exceeds that in Ga₂O₃ prior to irradiation and injection. The root cause of the electron injection-induced effect is attributed to the increase of minority carrier lifetime in the material due to trapping of non-equilibrium electrons on native point defects. It is, therefore, concluded that the electron injection is capable of “healing” the adverse impact of radiation in Ga₂O₃ and can be used for control of minority carrier transport and, therefore, device performance.

MnO₂ nanoparticles are considered nanozymes with intrinsic peroxidase-like activity and there are several reports on their application in the field of nanozyme-based sensing and detection, however, up to now, there is no report on the investigation of their biochemical and kinetics properties toward enzyme-mediated oxidations. Hence, in this work, the MnO₂ nanozymes were synthesized and characterized with different characterization methods. Thereafter, their biochemical properties including pH stability, thermal stability, and salt stability as well as their kinetics perfromances were evaluated toward n-electron irreversible oxidation of 3,3’-diaminobezedine. The results showed that the as-prepared nanozymes reveal their maximal enzyme-like activity over a wide pH range of 3.0-6.0 at a temperature of 23-25 ℃ toward oxidation of 3,3’-diaminobezedine. Besides, the salt stability studies exhibited that the as-mentioned nanozymes can save their maximal activity over a wide range of high salt concentrations over 3-7 M of NaCl. Moreover, the kinetics studies revealed a K_m as low as 1.6 mM and a V_max as high as 47 nM sec^-1 for the MnO₂ nanozymes toward irreversible oxidation of DAB to produce the brown-colored polyDAB.

In recent years, in addition to the commonly known wire-based processes of Directed Energy Deposition using lasers, a process variant using the electron beam has also developed to industrial market maturity. The process offers particular potential for processing highly conductive, reflective or oxidation-prone materials. However, for industrial usage there is a lack of comprehensive data on performance, process limits and possible applications. The present study deals with this problem using the example of the high-strength aluminum bronze CuAl8Ni6. Multi-stage test welds are used to determine the physically possible process limits and draw conclusions about the suitability of the parameters for additive manufacturing. For this purpose, optimal ranges for energy input, possible welding speeds and the scalability of the process were investigated. Finally, additive test specimens in the form of cylinders and walls are produced and the hardness profile, microstructure and mechanical properties are investigated. It is found that the material CuAl8Ni6 can be well processed by wire electron beam additive manufacturing. The microstructure is similar to a cast structure, the hardness profile over the height of the specimens is constant and the tensile strength and elongation at fracture values achieved correspond to the specification of the raw material.

Electron beam treatment of ZnS:Cu,Br (Cu activator content 0…0.6%wt.) radioluminescent phosphors as well as charge mixture with the electron energy 900 keV and absorbed dose of 600 kGy resulted in a enhancement of brightness up to 80%. The increased brightness is due to increase of content of wurtzite phase relative to sphalerite one with formation of wurtzite/sphalerite nanocomposite structure. Transformation of crystal structure is accompanied with corresponding change in content of active surface centers characteristic for sphalerite and wurtzite phases. A model describing surface centers of ZnS:Cu,Br radioluminescent phosphor is suggested.

Highly-correlated electrons – electrons that engage in strong electron-electron interactions – have been observed in transition metal oxides and quantum dots and can create unusual material behavior that is difficult to model, such as switching between a low resistance metal state and a high resistance Mott insulator state. Tests of devices using a layer-by-layer deposition process for forming multilayer arrays of ferritin (a transition metal (iron) oxide storage protein) have been previously reported that indicate that highly-correlated electron transport is occurring, consistent with models of electron transport in quantum dots. This paper reports the results of the effect of various degrees of structural homogeneity on the electrical characteristics of these ferritin arrays, as well as demonstrating that these structures can provide a switching function associated with the circuit that they are contained within, consistent with the observed behavior of highly-correlated electrons.

Polymethyl methacrylate (PMMA) is a transparent thermoplastic with excellent optical properties, transparent surface, low moisture absorption, tensile and electrical resistance. In this study, the alloy was prepared through PMMA and cycloolefin copolymer (COC) due to some similar properties. The mechanical test showed that properties such as impact resistance, elongation, tensile, and flexural strength decreased by adding COC by up to 20% due to less incompatibility and miscibility, but mentioned properties improved by adding COC 40% due to sub-phase generation. The DSC and DMTA tests showed improvement in the thermal properties of alloys by adding 40% COC. SEM micrographs exhibited a softer surface and more phase elongation of the alloy. Finally, the sample was selected as the optimal sample in terms of mechanical properties irradiated by electron beam, and amplification results showed that a dose of 50 KGY increased the mechanical and thermal properties relatively.

We consider the Dirac electron as a nonperturbative particle-like solution consistent with its own Kerr-Newman (KN) gravitational and electromagnetic field. We develop the earlier models of the KN electron regularized by Israel and López, and consider the non-perturbative electron model as a bag model formed by Higgs mechanism of symmetry breaking. The López regularization determines the unique shape of the electron in the form of a thin disk with a Compton radius reduced by 4π. In our model this disk is coupled with a closed circular string which is placed on the border of the disk and creates the caused by gravitation frame-dragging string tension produced by the vector potential of the Wilson loop. Using remarkable features of the Kerr-Schild coordinate system, which linearizes the Dirac equation, we obtain solutions of the Dirac equation consistent with the KN gravitational and electromagnetic field, and show that this solution takes the form of a massless relativistic string. Parallelism of this model with quantum representations in Heisenberg and Schrodinger pictures explains remarkable properties of the stringy electron model in the relativistic scattering processes.

Focused electron beam induced deposition is a versatile tool for the direct fabrication of complex-shaped nanostructures with unprecedented shape fidelity and resolution. While the technique is well-established for various materials, the direct electron beam writing of silver is still in its infancy. Here, five different silver carboxylates, three fluorinated: [Ag2(µ-O2CCF3)2], [Ag2(µ-O2CC2F5)2], [Ag2(µ-O2CC3F7)2] and two containing hydrogen: [Ag2(µ-O2CCMe2Et)2] and [Ag2(µ-O2CtBu)2] were examined and compared as potential precursors for focused electron beam induced deposition. All of the compounds show high sensitivity to electron dissociation and efficient dissociation of Ag-O bonds. The as-deposited materials showed high silver content from 42 at.% to above 70at.% and silver nano-crystal formation with impurities of carbon and fluorine incorporated between metal grains. A correlation of the number of carbon atoms in the precursor ligands and silver content of the deposited structures was found. The highest silver contents were achieved for compounds with the shortest CF chains. The deposited silver content depends on the balance of electron induced ligand co-deposition and thermal ligand desorption. Low electron flux is advantageous for high silver content. Our findings demonstrate that silver carboxylates constitute a promising group of precursors for focused electron beam nanoprinting of high silver content materials.

We present a laser-plasma electron accelerator module designed to be driven by high repetition rate lasers for industrial applications of laser-driven electron beams. It consists of a single vacuum chamber containing all the necessary components for producing, optimizing, and monitoring electron beams generated via laser wakefield acceleration in a gas jet. The core methods involve comprehensive metrological assessments, including rigorous temporal laser pulse characterization and contrast measurements, supplemented by detailed spatio-temporal distribution analyses of the laser system. Results demonstrate the good stability and reproducibility of the laser system, confirming its suitability for advanced scientific and industrial applications. We demonstrate the full functionality of the laser-plasma accelerator module and perform target density and laser-plasma characterizations. Our work is a first step towards the wide dissemination of fully integrated laser-plasma accelerator technology.

It has been recently demonstrated that inelastic helium-atom scattering from conducting surfaces can provide a direct measurement of the surface electron-phonon coupling constant (mass-enhancement factor ) via the temperature- or the incident-energy-dependence of the Debye-Waller exponent. The analysis of previous published as well as unpublished helium atom scattering diffraction data from the vicinal surfaces of copper (Cu(11),  = 3,5,7) and aluminium (Al(221) and Al(332)) permits to extract  for this class of surfaces, suggesting an enhancement with respect to the corresponding data for the low-index surfaces (111) and (001) above a possible roughening transition temperature. The specific role of steps as compared to that of terraces is briefly discussed.

Single-particle cryo-electron microscopy (cryo-EM SPA) has recently emerged as an exceptionally well-suited technique for determining the structure of membrane proteins (MPs). Indeed, in the last years, it was observed a huge increase in the number of MPs solved by cryo-EM SPA at a resolution better than 3.0 Å in the Protein Data Bank (PDB). However, sample preparation remains a significant challenge in the field. Here, we evaluated in the MPs solved by cryo-EM SPA deposited in the PDB in the last two years at a resolution below 3.0 Å the most critical parameters for sample preparation: i) the surfactant used for protein extraction from the membrane, ii) the surfactant, amphiphiles, nanodiscs or other molecules present in the vitrification step, iii) the vitrification method employed, and iv) the type of grids used. The aim is not to provide a definitive answer on the optimal sample conditions for cryo-EM SPA of MPs, but rather assess the current trends in the MP structural biology community towards obtaining high-resolution cryo-EM structures.

The relaxation processes induced by an exposure of the Ar matrices doped with CH4 (0.1 – 10%) to an electron beam were studied with a focus on the dynamics of radiolysis products – H atoms, H2 molecules, CH radicals, and energy transfer processes. Three channels of energy transfer to dopant and radiolysis products were discussed: by free charge carriers, free excitons and photons from the “intrinsic source” provided by emission of the self-trapped excitons. Radiolysis products along with the total yield of desorbing particles were monitored in a correlated manner. Analysis of methane transformation reactions induced by free excitons showed that the CH radical can be considered as a marker of the CH3 species. The competition between exciton self-trapping and energy transfer to the dopant and radiolysis products has been demonstrated. A nonlinear concentration behavior of the H atoms in doped Ar matrices has been established. Real-time correlated monitoring of optical emissions (H atom and CH3 radicals), particle ejection, and temperature revealed a nonmonotonic behavior of optical yields with a strong luminescence flash after almost an hour of exposure, which correlated with explosive pulse of particle ejection and temperature. The connection of this phenomenon with the processes of energy transfer and radical-radical recombination is discussed.

Under inflammatory conditions including lymphatic disorders, bone marrow-derived myeloid cells often express lymphatic endothelial cell (LEC) markers called LEC progenitor cells, which extend lymphatic vessels by fusing with existing lymphatic vessels. However, studies on the mechanism of lymphatic regeneration using three-dimensional images of lymphatic structures are limited. In this study, scanning electron microscopy (SEM) was used to observe the three-dimensional structure of lymphangiogenesis in a mouse model of secondary lymphedema. The model was established in C57BL/6J mice via circumferential incision in the inguinal region of the left hind limb. Skin samples were obtained from the lymphedema region on days 2, 5, and 8 after surgery. To determine lymphatic vessel positions using SEM analysis, we detected anti-lymphatic vessel endothelial hyaluronan receptor 1 (LYVE-1) immunoreactivity in serial sections and overlaid them during SEM observation. On days 2 and 5, spherical cells, probably myeloid cells, were attached and fused to the LYVE-1-positive lymphatic vessel walls. On day 8, spherical cells were converted to string-shaped cells, forming a new lymphatic vessel wall resembling an intraluminal pillar. Our results show the three-dimensional lymphatic structures formed during lymphatic regeneration.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

: The paper presents the results of uniaxial tensile tests of samples of hypoeutectic aluminum-silicon alloy A319. According to the results of which the influence of surface treatment by a pulsed electron beam on the mechanical properties of the material was determined. The peculiarities of localization of deformation in the material, caused by grinding of the surface layer material structure due to rapid crystallization during electron beam treatment were revealed. The surface treatment up to 100 µm depth leads to the formation of a fine dendritic columnar structure of silumin and to an increase in the plasticity of the samples. The influence of surface treatment affects the increase of deformation localization in the region of stable concentrator before failure. The largest increase in ductility and localization of deformation occurs during processing with energy density of 15 J/cm2. In the process of specimen deformation, unstable, metastable, and stable areas of plastic deformation localization are formed and replaced, and the formation of stable areas of localized plastic deformation, in which the specimen fails at the end of the test, can be detected at the initial stages of testing. In specimens, during testing in the zone of localized plastic deformation, bands are formed that pass through the entire surface of the specimen at an angle from 35 to 55 degrees to the axis of tension, their evolution leads to the formation of stable zones of localized plastic deformation and to the failure of the specimen.

Despite several decades of research, the physics underlying translation – protein synthesis at the ribosome – remains poorly studied. For instance, the mechanism coordinating various events occurring in distant parts of the ribosome is unknown. Very recently, we have suggested that this allosteric mechanism could be based on the transport of electric charges (electron holes) along RNA molecules and localization of these charges in the functionally important areas; this assumption was justified using tRNA as an example. In this study, we turn to the ribosome and show computationally that holes can also efficiently migrate within the whole ribosomal small subunit (SSU). The potential sites of charge localization in SSU are revealed, and it is shown that most of them are located in the functionally important areas of the ribosome – intersubunit bridges, Fe4S4 cluster and the pivot linking the SSU head to the body. As a result, we suppose that hole localization within the SSU can affect intersubunit rotation (ratcheting) and SSU head swiveling, in agreement with the scenario of electronic coordination of ribosome operation. We anticipate that our findings will improve the understanding of the translation process and advance the molecular biology and medicine.

The intramolecular ionic Diel-Alder (IIDA) reactions of two dieniminiums have been studied within the Molecular Electron Density Theory (MEDT) at the B97XD/6-311G(d,p) computational level. ELF topological analysis of dieniminiums shows that its electronic structure can been seen as the sum of those of butadiene and ethaniminium. The superelectrophilic character of dieniminiums accounts for the high intramolecular global electron density transfer taking place between the diene and iminium frameworks at the transition state structures (TSs) of these IIDA reactions. The activation enthalpy associated to the IIDA reaction of the experimental dieniminium, 8.7 kcal·mol-1, is closer to that of the ionic Diels-Alder (I-DA) reaction between butadiene and ethaniminium, 9.3 kcal·mol-1. However, the activation Gibbs free energy of the IIDA reaction is 12.7 kcal·mol-1 lower than that of the intermolecular I-DA reaction. The strong exergonic character of the IIDA reaction, higher than 17 kcal·mol-1, makes the reaction irreversible. These IIDA reactions present a total re/exo and si/endo diastereoselectivity, which is controlled by the most favourable chair conformation of the tetramethylene chain. Electron localization function (ELF) topological analysis of the single bond formation indicates that these IIDA reactions take place through a non-concerted two-stage one-step mechanism. Finally, ELF and atoms-in-molecules (AIM) topological analyses of the TS associated to inter and intramolecular processes show the great similitude among them.

A micro Sagnac interferometer integration is proposed for electron cloud distributed sensors. The Sagnac interferometer consists of four microring probes integrated into a Sagnac loop. Each of the microring probes is embedded with the silver bars to form the plasmonic wave oscillation. At the center microrings, electrons are trapped and oscillated by the whispering gallery modes (WGMs), where the plasmonic antennas are established and applied for wireless fidelity (WiFi) and light fidelity (LiFi) transmissions for distributed sensors. The antenna gains are 2.59dB, 0.93dB, 1.75dB, and 1.16dB respectively for the four antennas formed at the center microrings. The polarized light of 1.50µm wavelength is fed into the interferometer input, which is polarized randomly into upstream and downstream directions. The polarization components can be obtained by the space-time modulation control. By controlling the electron cloud spin orientation, the space-time projection can be applied, and the ultra-high measurement resolution can be obtained in terms of fast switching time (change in phase). In manipulation, the applied stimuli are substituted by the change in input source power. The light input power variation causes a change in electron cloud density. Similarly, when the electron cloud is excited by the microscopic medium, which can be employed as the microscopic sensors. The WGM sensors have sensitivities of 1.35µm-2, 0.90µm-2, 0.97µm-2 and, 0.81µm-2, respectively. The WGMs behave as a four-point probe for the electron cloud distributed sensors, where the electron cloud sensitivities of 2.31 prads-1mm3 (electrons)-1, 2.27prads-1mm3 (electrons)-1, 2.22 prads-1mm3(electrons)-1, 2.38prads-1mm3(electrons)-1 are respectively obtained.

This paper studies ionospheric vertical total electron content (VTEC) variations before the 2014 Mw8.2 Chile earthquake. VTEC derived from 14 GPS (Global Positioning System) stations and GIM (Global Ionospheric Map) were used to analyze ionospheric variations before the earthquake using the sliding interquartile range method, and results showed that significant positive VTEC anomalies occurred on 28 March. To explore possible causes of these anomalies, effects of solar and geomagnetic activities were examined, and VTEC variations during 17 March to 31 March in 2009-2013 were cross-compared. Also, VTEC for a full year before the earthquake was investigated. Results indicated that these anomalies were weakly associated with high solar activities and geomagnetic storms and that these anomalies were not normal seasonal and diurnal variations. An analysis of the spatial distribution of the observed anomalies was also presented, and it demonstrated that anomalies specifically appeared around the epicenter on 28 March. It suggests that observed anomalies may be associated with the subsequent Chile earthquake. Equatorial anomaly variations were analyzed to discuss the possible physical mechanism, and results showed that the equatorial anomaly unusually increased on 28 March, which indicates that anomalous electric fields generated in the earthquake preparation area and the meridional wind are possible causes of the observed ionospheric anomalies.

Scanning electron microscopy (SEM) is a powerful tool in the domain of material science, mining, and geology, owing to its enormous potential to provide unique insights into the micro and nanoscale worlds. This comprehensive review discusses the background development of SEM, basic SEM operation including the specimen preparation and imaging process, and fundamental theoretical calculations underlying the SEM operation. It provides foundational understanding to the engineers and scientists, who never got a chance to dig in-depth into the SEM, to understand the working and development of this robust analytical technique. The present review covers how SEM has been serving as a crucial tool in mineral characterization, with specific discussions on the working and research fronts of SEM-EDX, SEM-AM, SEM-MLA, and QEMSCAN. With automation gaining pace in the development of all spheres of technology, the understanding of uncertainties in SEM measurements is very important. The constraints in mineral phase identification by EDS spectra and sample preparation are conferred. In the end, future research directions for SEM are analyzed with the possible incorporation of machine learning, deep learning, and artificial intelligence tools, for automating the process of mineral identification, quantification, and efficient communication with the researchers, so that the analytical process robustness and objectivity can be improved, and the analysis time and the involved costs can be brought down. This review also discusses the idea of integrating robotics with SEM, to make the equipment portable, so that further mineral characterization insights can be gained not only on earth but also on other terrestrial grounds.

Two gallium porphyrins, a tetraphenyl GaCl porphyrin, termed as (TPP)GaCl, and an octaethylporphyrin GaCl porphyrin, termed as (OEP)GaCl were synthesized to use as electron cascade in ternary organic bulk heterojunction films. A perfect matching of both gallium porphyrins energy levels with that of poly(3-hexylthiophene-2,5-diyl) (P3HT) or poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) polymer donor and the 6,6-phenyl C71 butyric acid methyl ester (PCBM) fullerene acceptor forming an efficient cascade system that could facilitate electron transfer between donor and acceptor was demonstrated. Therefore, ternary organic solar cells (OSCs) using the two porphyrins in various concentration were fabricated, where a performance enhancement was obtained. In particular, (TPP)GaCl-based ternary OSCs of low concentration (1:0.05 vv%) exhibited a ~17 % increase of the power conversion efficiency (PCE) compared with the binary device due to improved exciton dissociation, electron transport and reduced recombination. On the other hand, ternary OSCs with the (TPP)GaCl of high concentration (1:0.1 vv%) and (OEP)GaCl (1:0.05 and 1:0.1 vv%) showed poorest efficiencies due to very rough nanomorphology and suppressed crystallinity of ternary films when the GaCl porphyrin introduced in the blend, as revealed from X-ray diffraction (XRD) and atomic force microscopy (AFM). The best performed devices exhibited also improved photostability, when exposed to sunlight illumination for a period of 8 h than the binary OSCs, attributed to the suppressed photodegradation of the ternary (TPP)GaCl 1:0.05-based photoactive film.

Photocatalytic degradation plays a crucial role in wastewater treatment, and the key to achieving high efficiency is to develop photocatalytic systems that possess excellent light absorption, carrier separation efficiency, and surface-active sites. Among various photocatalytic systems, S-type heterojunctions have shown remarkable potential for efficient degradation. This work delves into construction of S-type heterojunctions of ternary indium metal sulfide and bismuth ferrite nanofibers with introduction of sulfur vacancy defects and morphology modifications to enhance the photocatalytic degradation performance. Through the impregnation method, BiFeO₃/Zn₂S₄ heterojunction materials were synthesized and optimized30% BiFeO₃/Zn₂S₄ heterojunction exhibited superior photocatalytic performance with higher sulfur vacancy concentration than Zn₂S₄. The in-situ XPS results demonstrate that the electrons between Zn₂S₄ and BFO are transferred via S-Scheme, and after modification, Zn₂S₄ has a more favorable surface morphology for electron transport, and its flower-like structure interacts with the nanofibers of BFO, which has a further enhancement of the reaction efficiency for degrading pollutants. This exceptional material demonstrated a remarkable 99% degradation of Evans blue within 45 min and a significant 68% degradation of ciprofloxacin within 90 min. This work provides a feasible idea for developing photocatalysts to deal with the problem of polluted water resources under practical conditions.

Abstract: The morphological characteristics of the tongue of the Rahmani sheep (Ovis aries) were described using gross inspection, morphometry analysis, and scanning electron microscopy. Nine mature male sheep heads were slaughtered, and samples were taken right away. The tongue was dissected, and various samples were obtained for SEM. The tongue had two different types of lingual papillae: mechanical (filiform, conical, and lenticular papillae) and gustatory (fungiform and vallate papillae). The main papillae and several secondary and tertiary papillae combine to produce each filiform papilla. On the dorsal surface of the tongue, there were five different types of conical papillae dispersed throughout, as well as three huge conical papillae and various-sized flattening papillae in front of the frenulum linguae. Furthermore, on the torus linguae, two different types of lenticular papillae were found. The majority of fungiform papillae possessed prominent taste buds' pores and were button-shaped with a central depression region, particularly in the rostral section of the tongue. On either side of the torus linguae, there are two rows of round, elliptical, pyramidal, and oval circumvallate papillae. Each papilla is surrounded by flat, broad, undulating annular rods and papillary grooves. The lingual surface also included numerous lin-gual gland openings in a variety of forms, which increased in number at the root. Finally, variations in the form, size, and number of lingual papillae, as well as the distribution of lingual gland openings along the lingual surface, may provide efficiency to the Rahmani sheep's tongue when feeding hard forages and high fiber foods.

Spectroscopic methods are used to study the processes of accumulation of electron and hole trapping centers and energy transfer of electronic excitations to impurities in CaSO4-Mn and BaSO4-Mn. It is shown that the transfer of energy from the host to impurities occurs at the moment of charge transfer from the excited anionic complex SO_4^(2-) to the hybrid radiative electronic states at 2.95–3.1 eV formed from the electronic states of the Mn^(+)-SO_4^(-) and SO_4^(3-)-SO_4^(-) trapping centers. It was found that, in sulfates, under irradiation, as a result of charge transfer from excited anionic complexes of the host to the excited states of impurities Tl^(+),Cu^(+),Mn^(2+), hybrid radiative states emerge at 2.95–3.15 eV, occupying the same energy levels as the intrinsic electronic trapping center SO_4^(3-) of the host at 2.95–3.1 eV.

Field electron emission, or electron tunneling through a potential barrier under the influence of a strong electrostatic field, is of broad interest to the accelerator physics community. For example, it is the source of undesirable dark currents in resonant cavities, providing a limit to high-field operation. The classical approach to field electron emission is the Fowler-Nordheim (FN) framework, which incorporates a simplified surface potential and various assumptions. Here we build a more realistic model using the potential and charge densities derived from a density-functional theory (DFT) calculation. We examine the correction factors associated with each model assumption. Compared to the FN framework, our results can be extended up to 80 GV/m, a limit that has been reached in laser-induced strong field emission scenarios.

The response of the Cold-Electron Bolometers (CEBs), integrated into a 2-D array of dipole antennas, has been measured by irradiation from YBa$_2$Cu$_3$O$_{7-\delta}$ (YBCO) 50 $\mu$m long Josephson junction into the THz region at frequencies from 0.1 to 0.8 THz. The possibility of controlling the amplitude-frequency characteristic is demonstrated by the external magnetic field in the traveling wave regime of a long Josephson junction. YBCO junction has been formed on the bicrystal Zr$_{1-x}$Y$_x$O$_2$ (YSZ) substrate by magnetron sputtering and etching of the film. CEBs have been fabricated using an Al multilayer structure by a self-aligned shadow evaporation technique on Si substrate. Both receiver and oscillator have been located inside the same cryostat at 0.3K and 2.7K plates, respectively.